Merrica LED Mirror

Merrica LED Mirror

Specifications Electrical Rating 240V~ 50Hz 0.21A IP44 Features Defogger function Infrared On/ Off

5mm glass with PVC Backing LED Strip Lighting

3x Magnifier mirror back-lit Approx weight 8kg

Suitable for Portrait or Landscape installation The appliance is not intended to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure they do not to play with the appliance.

tile.com.au

Installation Warning

If hard wiring this mirror, it must be installed by a qualified electrician in accordance with AS/ NZS 3000 wiring rules. Switch off the power supply at the mains before installation and maintenance. A means of disconnection must be incorporated in the fixed wiring in accordance with the wiring rules. If the supply cord is damaged it must be replaced by the manufacturer, its service agent or similarly qualified person in order to avoid a hazard.

Installation Instructions

Suitable for installation in areas other than Zone 1 from below.

Rated IP44 for indoor use only.

ATTENTION: The mirror must be installed 15cm from nearest object to the bottom right corner where the Infrared On/ Off sensor is located. Otherwise the sensor may not operate properly.

1. Identify a position which does not fall into “Zone 1” as shown.

60

60

60

ZONE

2

225

ZONE

1

ZONE

2

ZONE

OUTSIDE ZONE

ZONE

ZONE

2

75

2

75

75

ZONE

2

ZONE

2

ZONE

1

2

Refers to the area above the bath or the shower, up to a height of 2.25 metres.

The minimum rating required here is IPX5.

Covers an area of 0.6 metres wide immediately next to, and all around “Zone 1”. Washbasins should also be treated as “Zone 2”.

The minimum rating required here is IPX4.

ZONE

ZONE

1

2

225

75

60

OUTSIDE ZONE

Has no special requirements, unless water jets are likely to be used for cleaning purposes.

pag. 1 1

Mirror Installation Instructions 2 a b E LAT

R

c

E PAP

2. In order to facilitate installation we have included

P TEM

a paper template to drill the holes in the wall.

d

3

3. Unfold the paper template and apply on the mirror

a

b

c

d

back to ensure that the holes match up.

4 4. Tape the paper template to the wall taking into

consideration the position of the mounting holes and the mirror edge. With a level, position the template so that it is perfectly level.

pag. 2

2

Mirror Installation Instructions 5. Ensure that there are no water pipes or electrical wiring behind the fixing points.

6

5

2/3mm

a b

c

a-b-c-d

6. Drill and insert the screw anchors suited to the type

d

of wall to which the cabinet mirror will be fixed (only screws in the case of wood studs) and install the fixing bar with its screws as shown.

Ă˜6mm

7A

pag. 3

3

Mirror Installation Instructions 7B.1

7B.1 In order to hardwire the mirror the back frame (A) must be separated from the mirror (B).

1. Remove all power to the mirror stainlesssteel steelside sidescrew screw 2. Remove the stinless 3. Unplug the connectors

7B.2

7B.2 Open Openthe theconnector connectorbox box and and replace replace the

the original electrical cordeletrical (red electrical cord original eletrical cord (red cord pictured) pictured) withwire the hard wirecord electrical with the hard eletrical (greencord eletrical (green electrical cord pictured). cord pictured).

pag. 4

4

Mirror Installation Instructions WIRING DIAGRAM

7B.3

1. Connect the hard wire eletrical cord to the connector box 2. Re-attach the connectors of the mirror back panel to the mirror 3. Fasten the stainless steel side screw securing the mirror back into the frame

9 8. Hang the mirror.

8

1 2

9. In the case that the mirror has stainless steel side screws ensure that they are tight.

Operation

Infrared On/ Off Sensor - bottom Moving your hand in proximity of the sensor turns the mirror light on and off.

Defogger On/ Off Switch - top The defogger is switched on and off via switch mounted on the side of the mirror. It will illuminate RED when switched on.

pag. 5 5

Maintenance and Care Clean with a soft cloth. Microfibre cloths are ideal. Do not use abrasives or solvents as these will damage the mirror and void the warranty conditions.

Warranty 2 years replacement parts only from date of purchase at Beaumont Tiles.

If a model is faulty in assembly or material and deemed unrepairable during the 2 year warranty period, a replacement model will be available for pick up from a nominated Beaumont Tiles outlet.

The warranty does not cover any associated labour costs without prior agreement with Beaumont Tiles.

The warranty is applicable when: The item has been correctly installed, maintained and used in accordance with instructions provided The failure is due to manufacturing fault Proof of purchase from Beaumont Tiles is provided The warranty does not cover faults caused by: Improper use Incorrect installation Installation in hard wiring situation by any other than a Licensed Electrician Normal wear and tear Poor care and maintenance Harsh cleansing materials For all warranty claims, please contact the Beaumont Tiles branch from where your original purchase was.

pag. 6

6