PRODUCT CATALOG - POLYKAR

PRODUCT CATALOG

CLICK TO OPEN

INTRODUCTION

BKP GROUP, a.s. was established in 1991 as a producer of polyester

putties. Since 1995 we have been producing in new operating premises, which are fully equipped with modern technological devices.

In Czech Republic we were the first to start with production of twocomponent polyester putties, which replace before used materials such as oil, acrylic and epoxy putties.

Over the years, we have broadened our production assortment with spraying putties, fillers, clear coats, protective spray coats, sprays, thinners, abrasives etc. Nowadays we are the biggest Czech producer of such products exporting into neighbouring countries.

Our products are supplied via distributors and wholesales into industry, auto paint shops and trade networks including foreign hobby shops We are holders of ISO 9001, ISO 14001 and OHSAS 18001 certificates.

BKP GROUP, a.s.

1.května 333 687 34 Uherský Brod 3 CZECH REPUBLIC www.bkp.cz obchod@bkp.cz Tel.: +420 572 61 00 61 Fax: +420 572 61 00 70

CLICK TO VIEW CONTENT Page 2

CONTENT

BASIC PUTTIES

page 4

SPECIAL PUTTIES

page 6

LAMINATING KITS

page 9

SPRAY PUTTIES

page 11

FILLERS

page 11

THINNERS

page 13

OTHER RANGE

page 14

________ VOLUMES OF PACKAGING

page 15

TECHNICAL DATA SHEETS

page 16

CLOSE

SELECT A CATEGORY

Page 3

BASIC PUTTIES

DESCRIPTION

SOFT PLUS

Middle dense, very well workable, soft, both upper and finishing fast putty used for filling of small and middle-sized disparities.

USAGE

Intended for common surface including castiron, aluminum, zinc and glass fibre

HARDENING

Red paste in tube in weight ratio 100:2

POT LIFE

5 minutes

SANDING

25 – 30 minutes

COLOUR

Bright orange

DESCRIPTION

UNIVERSAL

Middle rough, very well sandable, suitable as universal filling putty.

________ USAGE

Intended for common surface including castiron, aluminum, zinc and glass fibre

HARDENING

Red paste in tube in weight ratio 100:2

POT LIFE

5 minutes

SANDING

25 – 30 minutes

COLOUR

Ochry

NEXT PAGE

Page 4

BASIC PUTTIES

DESCRIPTION

FINEX

Very fine putty intended for filling of small disparities, striae and pits on car bodies, various metal products, iron castings or machine exteriors.

USAGE

It is easy to applicable and has very good sandability. It is suitable as finishing putty.

HARDENING

Red paste in tube in weight ratio 100:2

POT LIFE

7 minutes

SANDING

25 - 30 minutes

COLOUR

White

DESCRIPTION

MASTER

Middle dense, rougher putty intended for common surface including cast-iron, aluminum, zinc and glass fibre. It is suitable as universal filling putty.

________ USAGE

Recommended especially for container producers.

HARDENING

Red paste in tube in weight ratio 100:2

POT LIFE

5 minutes

SANDING

20 – 30 minutes

COLOUR

Ochry

BACK TO CONTENT

Page 5

SPECIAL PUTTIES

DESCRIPTION

GLAS

It contains high volume of fibreglass, which is necessary for formation of very strong, with fibreglass fixed layer of putty.

USAGE

Suitable especially for vaulting of missing parts in material, possible to put on in thick layer

HARDENING

Red paste in tube in weight ratio 100:2

POT LIFE

5 minutes

SANDING

20 - 30 minutes

COLOUR

Dark green

DESCRIPTION

METALIK

It has a high content of aluminium powder, what is necessary for better adhesion on filled surface. It has soft structure. It is well applicable.

________ USAGE

Intended for filling of light metals, galvanized sheets of car bodies, steel and glass fibre

HARDENING

Red paste in tube in weight ratio 100:2

POT LIFE

6 minutes

SANDING

25 – 35 minutes

COLOUR

Metallic

NEXT PAGE

Page 6

SPECIAL PUTTIES

DESCRIPTION

USAGE HARDENING POT LIFE SANDING COLOUR

DESCRIPTION

PLASTER

It is a special two component fine polyester putty with very high elasticity and increased adhesion to plastics. It is non-porous, easy to apply.

Excels with workability and easy sandable.

Red paste in tube in weight ratio 100:2 4 - 6 minutes 20 - 25 minutes Black

DĹ˜EVO (WOOD)

It has high content of wooden powder, which is necessary for chromatosis of the putty with common wood stains both before application and after hardening of putty.

________ HARDENING

Suitable for filling of wooden massive chipboard, blockboard and all products made from wood White paste in tube in weight ratio 100:2

POT LIFE

6 minutes

SANDING

30 minutes

COLOUR

Light brown (transparent)

USAGE

NEXT PAGE

Page 7

SPECIAL PUTTIES

DESCRIPTION

LIGHT

Light-weight putty, middle dense and very well workable. There is a minimal increase of weight of construction, so it is suitable for aircraft industry and ship-building sector.

USAGE

Intended for filling small and bigger disparities on common surfaces

HARDENING

Red paste in tube in weight ratio 100:3

POT LIFE

5 minutes

SANDING

20 - 30 minutes

COLOUR

Light blue

DESCRIPTION

RAPID CD

Middle rough, elastic two-component polyester putty intended for filling of large surfaces during railway carriages repairs.

________ USAGE

Excels in toughness, endures big load in bend and stroke during changing of temperatures and vibrations

HARDENING

Red paste in tube in weight ratio 100:2

POT LIFE

30 minutes

SANDING

6 – 8 hours

COLOUR

Light gray

NEXT PAGE

Page 8

SPECIAL PUTTIES

DESCRIPTION

LONG

Two-component putty intended for filling of dimensional workpieces, machine parts and large surfaces during the repairs of machine exteriors.

USAGE

Possible to use successfully also for filling of various metal products or iron castings

HARDENING

Red paste in tube in weight ratio 100:2

POT LIFE

30 minutes

SANDING

4 – 5 hours

COLOUR

Gray

BACK TO CONTENT

LAMINATING KITS DESCRIPTION

LAMINO REPAIR BOX

Two-component polyester repair set for small repairs.

The repair set is used for repairing of holes or splits in metal or laminate materials as for example rusted up places on car bodies, boats or camping caravans

________ USAGE

HARDENING

Red paste in tube in weight ratio 100:2

POT LIFE

8 - 10 minutes

SANDING

40 minutes

COLOUR

Light yellow transparent liquid

NEXT PAGE

Page 9

LAMINATING KITS LAMINO RESIN DESCRIPTION

Two-component polyester resin for repairing of laminate and lamination.

USAGE

Used for repairing of holes or splits in metal or laminate materials as for example rusted up places on car bodies, boats or camping caravans

HARDENING

Red paste in tube in weight ratio 100:2

POT LIFE

8 - 10 minutes

SANDING

40 minutes

COLOUR

Light yellow transparent liquid

DESCRIPTION

GLASS MAT

Non-woven glass mat Density 300g/m2 Size 1,5 m2

________ BACK TO CONTENT

Page 10

SPRAY PUTTIES

DESCRIPTION

USAGE

ST

Two-component spray putty intended for unification of surface between filled and no filled places, or for straightening of surface on car bodies.

It is used for formation of equable layer of putty on whole car body, which is necessary before application of filler and subsequently upper paint

HARDENING

Initiator 40 (liquid) in weight ratio 100:5

POT LIFE

40 minutes

SANDING

2 hours

COLOUR

white / gray

BACK TO CONTENT

FILLERS DESCRIPTION

FILLER 4:1 PREMIUM

Two-compound high-quality acrylic primer for majority of common surfaces.

________ USAGE

It has excellent filling properties. It is an ideal base which ensures high-quality appearance of coated things

HARDENING

4 parts of filler : 1 part of hardener in volume ratio

POT LIFE

45 minutes

SANDING

3 hours

COLOUR

gray / black

NEXT PAGE

Page 11

FILLERS

DESCRIPTION

FILLER 4:1 NORMAL

Two-compound high-quality acrylic primer for majority of common surfaces.

USAGE

It has excellent spill, perfect covering.

It dries fast also in thicker layers, is very well sandable.

HARDENING

4 parts of filler : 1 part of hardener in volume ratio

POT LIFE

60 minutes

SANDING

3 hours

COLOUR

white / gray / black

DESCRIPTION

FILLER 1K

One-component acrylic filler with excellent filling properties.

It can be applied on majority of common materials. It dries on air, is resistant against atmospheric and chemical influences. It is well sandable, easy to use.

________ USAGE

SANDING

45 – 60 minutes

COLOUR

Beige

BACK TO CONTENT

Page 12

THINNERS

DESCRIPTION

THINNER ACRYL

High quality acrylic thinner, which is used for modification of consistence of acrylic fillers and clearcoats. It is suitable into all acrylic coating compositions.

COLOUR

Transparent

DESCRIPTION

THINNER POLYESTER

Thinner, which is used for thinning of two-component polyester spray putties.

It is suitable also for cleaning of working tools polluted by all types of polyester putties.

Spray putties can be thinned max. 10% of their weight.

________ COLOUR

Transparent

NEXT PAGE

Page 13

THINNERS

DESCRIPTION

THINNER POLYURETAN

It is a thinner used for adjusting the consistency of fillers VARIOL FIL 4:1 PREMIUM and VARIOL FIL 2K PUR. It is suitable also for thinning acrylic paints and cleaning of working tools polluted by all types of polyurethane coatings.

Transparent

COLOUR

OTHER RANGE DESCRIPTION

TOPEKOR

It contains effective preparation for dispersion of anorganic and organic sediments, and inhibitor which protect against corrosion in closed systems of central heating. TOPEKOR can be used also in circulating systems where is the possibility of formation of scale or corrosion.

________ DOSAGE

Content of the container (500 ml) guarantee perfect protection of system with capacity up to 400 litres of water during minimally two years.

COMPATIBILITY It does not work aggresively on common materials WITH as iron, steel, cast iron, zinc coating, copper, MATERIALS polyethylene, polypropylene, rubber, sealing rubbers, teflon. It gets on glycols in water antifreezing systems.

BACK TO CONTENT

Page 14

VOLUMES OF PACKAGING Polyester putties are normally packed in cans in volumes 0.2, 0.5, 1, 2 or 5 kg.

It is also possible packing in a special 3 kg can for the batcher.

Each package includes the initiator.

Group packaging (cardboard, stretch-foil) can be adapted to customer requirements.

Overview of packaging product

putties

Fillers are packed in cans in volumes 1 or 4 liters. Hardeners are included in the appropriate packages 0.25 or 1 liters.

Thinners are commonly supplied in packages of 1 liter can, or 5 liters canister.

Transportation of so packaged products is thus excluded from the provisions of ADR, due to the limited quantity per unit.

fillers hardeners thinners

content

quantity [pcs] group

layer

pallet

0.2 kg

10

150

1500

0.5 kg

10

70

1050

1.0 kg

6

90

540

2.0 kg

3

30

300

3.0 kg

4

60

240

5.0 kg

-

35

105

1.0 l

6

84

504

4.0 l

-

20

100

0.25 l

10

70

1050

1.0 l

6

84

504

1.0 l

6

84

504

5.0 l

-

42

126

________ BACK TO CONTENT

Page 15

TECHNICAL DATA SHEETS SOFT PLUS

page 17

UNIVERSAL

page 18

FINEX

page 19

MASTER

page 20

GLAS

page 21

METALIK

page 22

PLASTER

page 23

WOOD

page 24

LIGHT

page 25

RAPID CD

page 26

LONG

page 27

LAMINO RESIN / REPAIR BOX

page 28

ST

page 29

FILLER 4:1 PREMIUM

page 30

FILLER 4:1 NORMAL

page 31

________ FILLER 1K

page 32

THINNER ACRYL

page 33

THINNER POLYESTER

page 34

THINNER POLYURETAN

page 35

TOPEKOR

page 36

BACK TO CONTENT

SELECT TDS

Page 16

TECHNICAL DATA SHEET

POLYKAR SOFT PLUS technical description: 10. 10. 2012 DESCRIPTION AND USAGE

SOFT PLUS is a two component polyester medium dense, well-workable putty for filling small to medium sized disparities. It is intended for common surface including iron, aluminum, zinc and fiberglass. It is very well sandable, pore-free, it is also applicable to even out inequalities on wood (harder types), concrete, etc. The putty is due to its structure very well applicable.

ENVIRONMENT

The putty must not be used for filling places which are in direct contact with food and drinking water.

VOC VOLUME

VOC = 51 g / l This product complies with EU Directive (2004/42/EC), which gives for the preparation of this category (B / b) the limit value of volatile matter content of 250 g / l in finished product.

APPLICATION

Get rid of rust and abrade the bonded surface by sandpaper P80. Surface must be clean, dry and free of dust and grease. For maximum corrosion protection use epoxy or polyurethane basecoat. Do not apply the putty on reactive, single or nitrocellulose basecoats. Apply with a trowel.

HARDENING

The putty is hardened with hardener (PE-initiator, dibenzoyl peroxide, red paste in tube) in weight ratio: - 100 parts of putty : 2 parts of hardener – recommended ratio for temperature 23°C

POT LIFE

The putty is necessary to be used within 5 minutes after mixing with hardener at temperature 23°C and hardening ratio 100:2. Adjusting of the hardening ratio can partly eliminate the influence of temperature on the potlife. At lower temperatures (at least 17°C), the potlife increases, at higher temperatures is reduced. Do not exceed the recommended hardening ratio.

SANDING

The putty is sandable after 25-30 minutes at temperature 23°C and hardening ratio 100:2. Rough sanding begins with sanding paper P80-120 and finishes with sanding paper P180-240. For sanding is recommended to use rotating or vibrating sander.

UPPER COATINGS

It is possible to use all common paint systems on the putty. The putty withstands temperatures of 80-110 °C.

TOOLS CLEANING

Dirty parts of tools for filling can be cleaned with THINNER POLYESTER or nitrothinner C-6000. Only non-hardened putty can be cleaned.

STORAGE

It is necessary to ensure the temperature from +5°C to + 25°C and avoid direct solar radiation during storage and transport. Dash of the resin on the surface of putty is acceptable. We guarantee shelf life and quality of the product for 12 months.

PACKAGING

- 0,2 kg, 0,5 kg, 1 kg, 1,8 kg, 5 kg, 15 kg – a can - 3 kg – a can for batching plant

COLOUR

Bright orange

BACK TO LIST Page 17

TECHNICAL DATA SHEET

POLYKAR UNIVERSAL technical description: 10. 10. 2012 DESCRIPTION AND USAGE

UNIVERSAL is a two polyester medium rough and very well applicable putty. Due to its higher viscosity is perfectly sandable. It is an universal pore-free putty intended for the common surface including iron, aluminum and fiberglass.

ENVIRONMENT

The putty must not be used for filling places which are in direct contact with food and drinking water.

VOC VOLUME

VOC = 119 g / l This product complies with EU Directive (2004/42/EC), which gives for the preparation of this category (B / b) the limit value of volatile matter content of 250 g / l in finished product.

APPLICATION

Get rid of rust and abrade the bonded surface by sandpaper P80. Surface must be clean, dry and free of dust and grease. For maximum corrosion protection use epoxy or polyurethane basecoat. Do not apply the putty on reactive, single or nitrocellulose basecoats. Apply with a trowel.

HARDENING

The putty is hardened with hardener (PE-initiator, dibenzoyl peroxide, red paste in tube) in weight ratio: - 100 parts of putty : 2 parts of hardener – recommended ratio for temperature 23°C

POT LIFE

The putty is necessary to be used within 5 minutes after mixing with hardener at temperature 23°C and hardening ratio 100:2. Adjusting of the hardening ratio can partly eliminate the influence of temperature on the potlife. At lower temperatures (at least 17°C), the potlife increases, at higher temperatures is reduced. Do not exceed the recommended hardening ratio.

SANDING

The putty is sandable after 25-30 minutes at temperature 23°C and hardening ratio 100:2. Rough sanding begins with sanding paper P80-120 and finishes with sanding paper P180-240. For sanding is recommended to use rotating or vibrating sander.

UPPER COATINGS

It is possible to use all common paint systems on the putty. The putty withstands temperatures of 80-110 °C.

TOOLS CLEANING

Dirty parts of tools for filling can be cleaned with THINNER POLYESTER or nitrothinner C-6000. Only non-hardened putty can be cleaned.

STORAGE

It is necessary to ensure the temperature from +5°C to + 25°C and avoid direct solar radiation during storage and transport. Dash of the resin on the surface of putty is acceptable. We guarantee shelf life and quality of the product for 12 months.

PACKAGING

- 0,2 kg, 0,5 kg, 1 kg, 1,8 kg, 5 kg, 15 kg – a can - 3 kg – a can for batching plant

COLOUR

Beige green

BACK TO LIST Page 18

TECHNICAL DATA SHEET

POLYKAR FINEX technical description: 10. 10. 2012 DESCRIPTION AND USAGE

FINEX is a two-component soft putty intended for filling of small disparities, striae and pits on car bodies. It is possible to fill various metal products, iron castings or machine exteriors successfully with this product. It is applicable also for straightening of disparities on wood (harder kinds), glass fibre, concrete etc. Thanks to its very fine structure the putty is easy to applicable and has very good sandability. It is suitable as finishing putty.

ENVIRONMENT

The putty must not be used for filling places which are in direct contact with food and drinking water.

VOC VOLUME

VOC = 99 g / l This product complies with EU Directive (2004/42/EC), which gives for the preparation of this category (B / b) the limit value of volatile matter content of 250 g / l in finished product.

APPLICATION

Get rid of rust and abrade the bonded surface by sandpaper P80. Surface must be clean, dry and free of dust and grease. For maximum corrosion protection use epoxy or polyurethane basecoat. Do not apply the putty on reactive, single or nitrocellulose basecoats. Apply with a trowel.

HARDENING

The putty is hardened with hardener (PE-initiator, dibenzoyl peroxide, red paste in tube) in weight ratio: - 100 parts of putty : 2 parts of hardener – recommended ratio for temperature 23°C

POT LIFE

The putty is necessary to be used within 7 minutes after mixing with hardener at temperature 23°C and hardening ratio 100:2. Adjusting of the hardening ratio can partly eliminate the influence of temperature on the potlife. At lower temperatures (at least 17°C), the potlife increases, at higher temperatures is reduced. Do not exceed the recommended hardening ratio.

SANDING

The putty is sandable after 25-30 minutes at temperature 23°C and hardening ratio 100:2. Rough sanding begins with sanding paper P120-180 and finishes with sanding paper P240-320. For sanding is recommended to use rotating or vibrating sander.

UPPER COATINGS

It is possible to use all common paint systems on the putty. The putty withstands temperatures of 80-110 °C.

TOOLS CLEANING

Dirty parts of tools for filling can be cleaned with THINNER POLYESTER or nitrothinner C-6000. Only non-hardened putty can be cleaned.

STORAGE

It is necessary to ensure the temperature from +5°C to + 25°C and avoid direct solar radiation during storage and transport. Dash of the resin on the surface of putty is acceptable. We guarantee shelf life and quality of the product for 12 months.

PACKAGING

- 0,2 kg, 0,5 kg, 1 kg, 2 kg, 5 kg, 15 kg – a can - 3 kg – a can for batching plant

COLOUR

White

BACK TO LIST Page 19

TECHNICAL DATA SHEET

POLYKAR MASTER technical description: 10. 10. 2012 DESCRIPTION AND USAGE

MASTER is middle dense, rougher putty intended for common surface including castiron, aluminum, zinc and glass fibre. It is very well sandable, without pits, suitable as universal filling putty. It is recommended especially or container producers.

ENVIRONMENT

The putty must not be used for filling places which are in direct contact with food and drinking water.

VOC VOLUME

VOC = 53 g / l This product complies with EU Directive (2004/42/EC), which gives for the preparation of this category (B / b) the limit value of volatile matter content of 250 g / l in finished product.

APPLICATION

Get rid of rust and abrade the bonded surface by sandpaper P80. Surface must be clean, dry and free of dust and grease. For maximum corrosion protection use epoxy or polyurethane basecoat. Do not apply the putty on reactive, single or nitrocellulose basecoats. Apply with a trowel.

HARDENING

The putty is hardened with hardener (PE-initiator, dibenzoyl peroxide, red paste in tube) in weight ratio: - 100 parts of putty : 2 parts of hardener – recommended ratio for temperature 23°C

POT LIFE

The putty is necessary to be used within 5 minutes after mixing with hardener at temperature 23°C and hardening ratio 100:2. Adjusting of the hardening ratio can partly eliminate the influence of temperature on the potlife. At lower temperatures (at least 17°C), the potlife increases, at higher temperatures is reduced. Do not exceed the recommended hardening ratio.

SANDING

The putty is sandable after 20-30 minutes at temperature 23°C and hardening ratio 100:2. Rough sanding begins with sanding paper P80-120 and finishes with sanding paper P180-240. For sanding is recommended to use rotating or vibrating sander.

UPPER COATINGS

It is possible to use all common paint systems on the putty. The putty withstands temperatures of 80-110 °C.

TOOLS CLEANING

Dirty parts of tools for filling can be cleaned with THINNER POLYESTER or nitrothinner C-6000. Only non-hardened putty can be cleaned.

STORAGE

It is necessary to ensure the temperature from +5°C to + 25°C and avoid direct solar radiation during storage and transport. Dash of the resin on the surface of putty is acceptable. We guarantee shelf life and quality of the product for 12 months.

PACKAGING

- 0,2 kg, 0,5 kg, 1 kg, 2 kg, 5 kg, 15 kg – a can - 3 kg – a can for batching plant

COLOUR

Ochry

BACK TO LIST Page 20

TECHNICAL DATA SHEET

POLYKAR GLAS technical description: 10. 10. 2012 DESCRIPTION AND USAGE

GLAS is a special two component polyester putty intended for the common surface including iron, aluminum, zinc and fiberglass. It is especially suited for bridging the missing parts of the material, it can be applied in a thick layer. It has a high content of glass fiber, which allows you to create very strong layer of putty tied by fiberglass, that can be sanded as needed.

ENVIRONMENT

The putty must not be used for filling places which are in direct contact with food and drinking water.

VOC VOLUME

VOC = 67 g / l This product complies with EU Directive (2004/42/EC), which gives for the preparation of this category (B / b) the limit value of volatile matter content of 250 g / l in finished product.

APPLICATION

Get rid of rust and abrade the bonded surface by sandpaper P80. Surface must be clean, dry and free of dust and grease. For maximum corrosion protection use epoxy or polyurethane basecoat. Do not apply the putty on reactive, single or nitrocellulose basecoats. Apply with a trowel.

HARDENING

The putty is hardened with hardener (PE-initiator, dibenzoyl peroxide, red paste in tube) in weight ratio: - 100 parts of putty : 2 parts of hardener – recommended ratio for temperature 23°C

POT LIFE

The putty is necessary to be used within 5 minutes after mixing with hardener at temperature 23°C and hardening ratio 100:2. Adjusting of the hardening ratio can partly eliminate the influence of temperature on the potlife. At lower temperatures (at least 17°C), the potlife increases, at higher temperatures is reduced. Do not exceed the recommended hardening ratio.

SANDING

The putty is sandable after 20-30 minutes at temperature 23°C and hardening ratio 100:2. Rough sanding begins with sanding paper P60-80 and finishes with sanding paper P120. For sanding is recommended to use rotating or vibrating sander.

UPPER COATINGS

It is possible to use all common paint systems on the putty. The putty withstands temperatures of 80-110 °C.

TOOLS CLEANING

Dirty parts of tools for filling can be cleaned with THINNER POLYESTER or nitrothinner C-6000. Only non-hardened putty can be cleaned.

STORAGE

It is necessary to ensure the temperature from +5°C to + 25°C and avoid direct solar radiation during storage and transport. Dash of the resin on the surface of putty is acceptable. We guarantee shelf life and quality of the product for 12 months.

PACKAGING

- 0,15 kg, 0,5 kg, 1 kg, 1,8 kg, 5 kg, 15 kg – a can - 3 kg – a can for batching plant

COLOUR

Green

BACK TO LIST Page 21

TECHNICAL DATA SHEET

POLYKAR METALIK technical description: 10. 10. 2012 DESCRIPTION AND USAGE

METALIK is a special two component polyester putty designed for filling light metal, galvanized sheets of car bodies, steel and fiberglass. It has a high content of aluminium powder, which brings a soft structure and good applicability, easy sanding and increased adhesion to filled surface.

ENVIRONMENT

The putty must not be used for filling places which are in direct contact with food and drinking water.

VOC VOLUME

VOC = 65 g / l This product complies with EU Directive (2004/42/EC), which gives for the preparation of this category (B / b) the limit value of volatile matter content of 250 g / l in finished product.

APPLICATION

Get rid of rust and abrade the bonded surface by sandpaper P80. Surface must be clean, dry and free of dust and grease. For maximum corrosion protection use epoxy or polyurethane basecoat. Do not apply the putty on reactive, single or nitrocellulose basecoats. Apply with a trowel.

HARDENING

The putty is hardened with hardener (PE-initiator, dibenzoyl peroxide, red paste in tube) in weight ratio: - 100 parts of putty : 2 parts of hardener – recommended ratio for temperature 23°C

POT LIFE

The putty is necessary to be used within 6 minutes after mixing with hardener at temperature 23°C and hardening ratio 100:2. Adjusting of the hardening ratio can partly eliminate the influence of temperature on the potlife. At lower temperatures (at least 17°C), the potlife increases, at higher temperatures is reduced. Do not exceed the recommended hardening ratio.

SANDING

The putty is sandable after 25-35 minutes at temperature 23°C and hardening ratio 100:2. Rough sanding begins with sanding paper P80-120 and finishes with sanding paper P180-240. For sanding is recommended to use rotating or vibrating sander.

UPPER COATINGS

It is possible to use all common paint systems on the putty. The putty withstands temperatures of 80-110 °C.

TOOLS CLEANING

Dirty parts of tools for filling can be cleaned with THINNER POLYESTER or nitrothinner C-6000. Only non-hardened putty can be cleaned.

STORAGE

It is necessary to ensure the temperature from +5°C to + 25°C and avoid direct solar radiation during storage and transport. Dash of the resin on the surface of putty is acceptable. We guarantee shelf life and quality of the product for 12 months.

PACKAGING

- 0,2 kg, 0,5 kg, 1 kg, 1,8 kg, 5 kg, 15 kg – a can - 3 kg – a can for batching plant

COLOUR

Green

BACK TO LIST Page 22

TECHNICAL DATA SHEET

POLYKAR PLASTER technical description: 10. 10. 2012 DESCRIPTION AND USAGE

PLASTER is a special two component fine polyester putty with very high elasticity and increased adhesion to plastics. It is non-porous, easy to apply and very well sandable.

ENVIRONMENT

The putty must not be used for filling places which are in direct contact with food and drinking water.

VOC VOLUME

VOC = 35 g / l This product complies with EU Directive (2004/42/EC), which gives for the preparation of this category (B / b) the limit value of volatile matter content of 250 g / l in finished product.

APPLICATION

Get rid of rust and abrade the bonded surface by sandpaper P150. Surface must be clean, dry and free of dust and grease. Apply with a trowel.

HARDENING

The putty is hardened with hardener (PE-initiator, dibenzoyl peroxide, red paste in tube) in weight ratio: - 100 parts of putty : 2 parts of hardener – recommended ratio for temperature 23°C

POT LIFE

The putty is necessary to be used within 4-6 minutes after mixing with hardener at temperature 23°C and hardening ratio 100:2. Adjusting of the hardening ratio can partly eliminate the influence of temperature on the potlife. At lower temperatures (at least 17°C), the potlife increases, at higher temperatures is reduced. Do not exceed the recommended hardening ratio.

SANDING

The putty is sandable after 20-25 minutes at temperature 23°C and hardening ratio 100:2. Rough sanding begins with sanding paper P150 and finishes with sanding paper P240. For sanding is recommended to use rotating or vibrating sander.

UPPER COATINGS

It is possible to use all common paint systems on the putty. The putty withstands temperatures of 80-110 °C.

TOOLS CLEANING

Dirty parts of tools for filling can be cleaned with THINNER POLYESTER or nitrothinner C-6000. Only non-hardened putty can be cleaned.

STORAGE

It is necessary to ensure the temperature from +5°C to + 25°C and avoid direct solar radiation during storage and transport. Dash of the resin on the surface of putty is acceptable. We guarantee shelf life and quality of the product for 12 months.

PACKAGING

- 0,2 kg, 0,5 kg, 1 kg, 2 kg, 5 kg, 15 kg – a can - 3 kg – a can for batching plant

COLOUR

Black

BACK TO LIST Page 23

TECHNICAL DATA SHEET

POLYKAR WOOD technical description: 10. 10. 2012 DESCRIPTION AND USAGE

WOOD is a special two-component polyester putty intended for filling of all kinds of wood. It is suitable for filling of massif, chipboard, blockboard and all products made from wood. HOLS has high content of wooden powder, which is necessary for chromatosis of the putty with common wood stains both before application and after hardening of putty. WOOD is both well sandable and elastic, what is necessary according to volume non-stability of wooden materials.

ENVIRONMENT

The putty must not be used for filling places which are in direct contact with food and drinking water.

VOC VOLUME

VOC = 50 g / l This product complies with EU Directive (2004/42/EC), which gives for the preparation of this category (B / b) the limit value of volatile matter content of 250 g / l in finished product.

APPLICATION

Bonded wood surface is necessary to get rid of moisture, dust, old paint and sand by sandpaper. Apply with a trowel. If you need to create a larger layer of putty, we recommend filling in multiple layers of about 5 mm. Between the layers wait at least 30 minutes.

HARDENING

The putty is hardened with hardener (PE-initiator, dibenzoyl peroxide, white paste in tube) in weight ratio: - 100 parts of putty : 2 parts of hardener – recommended ratio for temperature 23°C

POT LIFE

The putty is necessary to be used within 6 minutes after mixing with hardener at temperature 23°C and hardening ratio 100:2. Adjusting of the hardening ratio can partly eliminate the influence of temperature on the potlife. At lower temperatures (at least 17°C), the potlife increases, at higher temperatures is reduced. Do not exceed the recommended hardening ratio.

SANDING

The putty is sandable after 30 minutes at temperature 23°C and hardening ratio 100:2. Rough sanding begins with sanding paper P80-120 and finishes with finer sandpaper as needed. For sanding is recommended to use rotating or vibrating sander.

UPPER COATINGS

The putty can be covered with commercially available stains (based on water or alcohol). It can be used for any conventional coating systems.

TOOLS CLEANING

Dirty parts of tools for filling can be cleaned with THINNER POLYESTER or nitrothinner C-6000. Only non-hardened putty can be cleaned.

STORAGE

It is necessary to ensure the temperature from +5°C to + 25°C and avoid direct solar radiation during storage and transport. Dash of the resin on the surface of putty is acceptable. We guarantee shelf life and quality of the product for 12 months.

PACKAGING

- 0,15 kg, 0,5 kg, 0,75 kg, 1,5 kg, 4 kg, 12 kg – a can - 2,5 kg – a can for batching plant

COLOUR

Light brown transparent

BACK TO LIST Page 24

TECHNICAL DATA SHEET

POLYKAR LIGHT technical description: 10. 10. 2012 DESCRIPTION AND USAGE

LIGHT is a considerably light-weight putty, middle dense and very well workable. This upper putty is intended for filling small and bigger disparities. It is intended for common surface. It has lower adhesion on aluminum and zinc materials. Thanks to low density it is very well sandable with severalfold lower abrasive consumption. It has high resistance of stress on material. There is a minimal increase of weight of construction, so it is suitable for aircraft industry, ship-building sector and auto-tuning.

ENVIRONMENT

The putty must not be used for filling places which are in direct contact with food and drinking water.

VOC VOLUME

VOC = 12 g / l This product complies with EU Directive (2004/42/EC), which gives for the preparation of this category (B / b) the limit value of volatile matter content of 250 g / l in finished product.

APPLICATION

Get rid of rust and abrade the bonded surface by sandpaper P80. Surface must be clean, dry and free of dust and grease. For maximum corrosion protection use epoxy or polyurethane basecoat. Do not apply the putty on reactive, single or nitrocellulose basecoats. Apply with a trowel.

HARDENING

The putty is hardened with hardener (PE-initiator, dibenzoyl peroxide, red paste in tube) in weight ratio: - 100 parts of putty : 3 parts of hardener – recommended ratio for temperature 23°C

POT LIFE

The putty is necessary to be used within 5 minutes after mixing with hardener at temperature 23°C and hardening ratio 100:3. Adjusting of the hardening ratio can partly eliminate the influence of temperature on the potlife. At lower temperatures (at least 17°C), the potlife increases, at higher temperatures is reduced. Do not exceed the recommended hardening ratio.

SANDING

The putty is sandable after 20-30 minutes at temperature 23°C and hardening ratio 100:3. Rough sanding begins with sanding paper P80-120 and finishes with sanding paper P240. For sanding is recommended to use rotating or vibrating sander.

UPPER COATINGS

It is possible to use all common paint systems on the putty. The putty withstands temperatures of 80-110 °C.

TOOLS CLEANING

Dirty parts of tools for filling can be cleaned with THINNER POLYESTER or nitrothinner C-6000. Only non-hardened putty can be cleaned.

STORAGE

It is necessary to ensure the temperature from +5°C to + 25°C and avoid direct solar radiation during storage and transport. Dash of the resin on the surface of putty is acceptable. We guarantee shelf life and quality of the product for 12 months.

PACKAGING

- 0,6 l, 1,0 l – a can

COLOUR

Light blue

BACK TO LIST Page 25

TECHNICAL DATA SHEET

POLYKAR RAPID CD technical description: 10. 10. 2012 DESCRIPTION AND USAGE

RAPID CD is middle rough, elastic two-component polyester putty intended for filling of large surfaces during railway carriages repairs. RAPID CD is possible to use successfully for filling of various metal products, iron castings or machine exteriors. It is applicable on straightening of disparities on wood (harder kinds), glass fibre, concrete, stone etc. The putty has good filling ability and is well workable and sandable. It excels in toughness, endures big load in bend and stroke during changing of temperatures and vibrations. This putty has the certificate from State Testing Laboratory ČD (Czech railway) for repairs of railway carriages surfaces.

ENVIRONMENT

The putty must not be used for filling places which are in direct contact with food and drinking water.

VOC VOLUME

VOC = 91 g / l This product complies with EU Directive (2004/42/EC), which gives for the preparation of this category (B / b) the limit value of volatile matter content of 250 g / l in finished product.

APPLICATION

Get rid of rust and abrade the bonded surface by sandpaper P80. Surface must be clean, dry and free of dust and grease. For maximum corrosion protection use epoxy or polyurethane basecoat. Do not apply the putty on reactive, single or nitrocellulose basecoats. Apply with a trowel.

HARDENING

The putty is hardened with hardener (PE-initiator, dibenzoyl peroxide, red paste in tube) in weight ratio: - 100 parts of putty : 2 parts of hardener – recommended ratio for temperature 23°C

POT LIFE

The putty is necessary to be used within 30 minutes after mixing with hardener at temperature 23°C and hardening ratio 100:2. Adjusting of the hardening ratio can partly eliminate the influence of temperature on the potlife. At lower temperatures (at least 17°C), the potlife increases, at higher temperatures is reduced. Do not exceed the recommended hardening ratio.

SANDING

The putty is sandable after 6-8 hours at temperature 23°C and hardening ratio 100:2.

Rough sanding begins with sanding paper P80-120 and finishes with sanding paper P180-240. For sanding is recommended to use rotating or vibrating sander.

UPPER COATINGS

It is possible to use all common paint systems on the putty. The putty withstands temperatures of 80-110 °C.

TOOLS CLEANING

Dirty parts of tools for filling can be cleaned with THINNER POLYESTER or nitrothinner C-6000. Only non-hardened putty can be cleaned.

STORAGE

It is necessary to ensure the temperature from +5°C to + 25°C and avoid direct solar radiation during storage and transport. Dash of the resin on the surface of putty is acceptable. We guarantee shelf life and quality of the product for 12 months.

PACKAGING

- 2 kg, 5 kg, 15 kg – a can - 3 kg – a can for batching plant

COLOUR

Light gray

BACK TO LIST Page 26

TECHNICAL DATA SHEET

POLYKAR LONG technical description: 10. 10. 2012 DESCRIPTION AND USAGE

LONG is soft surface two-component putty intended for filling of dimensional workpieces, machine parts and large surfaces during the repairs of machine exteriors.

LONG is possible to use successfully also for filling of various metal products or iron castings. The putty has thinner consistence and it is very well workable. It is applicable also for straightening of disparities on wood (harder kinds), glass fibre, concrete, stone etc. The putty has excellent adhesion on various surfaces, good elasticity, is easy applicable and excellent sandable.

ENVIRONMENT

The putty must not be used for filling places which are in direct contact with food and drinking water.

VOC VOLUME

VOC = 53 g / l This product complies with EU Directive (2004/42/EC), which gives for the preparation of this category (B / b) the limit value of volatile matter content of 250 g / l in finished product.

APPLICATION

Get rid of rust and abrade the bonded surface by sandpaper P80. Surface must be clean, dry and free of dust and grease. For maximum corrosion protection use epoxy or polyurethane basecoat. Do not apply the putty on reactive, single or nitrocellulose basecoats. Apply with a trowel.

HARDENING

The putty is hardened with hardener (PE-initiator, dibenzoyl peroxide, red paste in tube) in weight ratio: - 100 parts of putty : 2 parts of hardener – recommended ratio for temperature 23°C

POT LIFE

The putty is necessary to be used within 30 minutes after mixing with hardener at temperature 23°C and hardening ratio 100:2. Adjusting of the hardening ratio can partly eliminate the influence of temperature on the potlife. At lower temperatures (at least 17°C), the potlife increases, at higher temperatures is reduced. Do not exceed the recommended hardening ratio.

SANDING

The putty is sandable after 4-5 hours at temperature 23°C and hardening ratio 100:2.

Rough sanding begins with sanding paper P80-120 and finishes with sanding paper P180-240. For sanding is recommended to use rotating or vibrating sander.

UPPER COATINGS

It is possible to use all common paint systems on the putty. The putty withstands temperatures of 80-110 °C.

TOOLS CLEANING

Dirty parts of tools for filling can be cleaned with THINNER POLYESTER or nitrothinner C-6000. Only non-hardened putty can be cleaned.

STORAGE

It is necessary to ensure the temperature from +5°C to + 25°C and avoid direct solar radiation during storage and transport. Dash of the resin on the surface of putty is acceptable. We guarantee shelf life and quality of the product for 12 months.

PACKAGING

- 2 kg, 5 kg, 15 kg – a can - 3 kg – a can for batching plant

COLOUR

Light gray

BACK TO LIST Page 27

TECHNICAL DATA SHEET

POLYKAR LAMINO

resin / repair

box

DESCRIPTION AND USAGE

technical description: 10. 10. 2012 LAMINO is a two-component polyester resin / repair set for small repairs. The repair set is used for repairing of holes or splits in metal or laminate materials as for example rusted up places on car bodies, boats or camping caravans. Glass texture soaked with polyester resin forms steady base for application of next layers of putties during the repair.

ENVIRONMENT

This product must not be used for filling places which are in direct contact with food and drinking water.

VOC VOLUME

VOC = 62 g / l This product complies with EU Directive (2004/42/EC), which gives for the preparation of this category (B / b) the limit value of volatile matter content of 250 g / l in finished product.

APPLICATION

Repaired surface must be without rust and old coatings. It is necessary to degrease the surface carefully, eventually to roughen with sanding paper: - glass fibre – sanding paper P40 - steel, galvanized steel – sanding paper P60 Before starting the repair it is necessary to cut out suitable piece of glass texture.

Prepared mixture of resin and hardener is applicated on repaired place by brush, then the glass texture is laid. After that also the glass texture shall be soaked. It is possible to lay more layers of glas texture, if it is necessary.

HARDENING

The putty is hardened with hardener (PE-initiator, dibenzoyl peroxide, red paste in tube) in weight ratio: - 100 parts of putty : 2 parts of hardener – recommended ratio for temperature 23°C

POT LIFE

The putty is necessary to be used within 8-10 minutes after mixing with hardener at temperature 23°C and hardening ratio 100:2. Adjusting of the hardening ratio can partly eliminate the influence of temperature on the potlife. At lower temperatures (at least 17°C), the potlife increases, at higher temperatures is reduced. Do not exceed the recommended hardening ratio.

SANDING

Repaired place is sandable after 40 minutes at temperature 23°C and hardening ratio 100:2. For dry sanding it is used the sanding paper P80 – P180.

UPPER COATINGS

The repair should be finished with putties POLYKAR GLAS or POLYKAR SOFT PLUS, eventually with extra soft putty POLYKAR FINEX, which alignes the margins finely. We recommend also to use spray putty or filler. After that it is possible to use all common paint systems. Hardened resin resists common baking temperatures 80 – 110°C.

TOOLS CLEANING

Dirty parts of tools for filling can be cleaned with THINNER POLYESTER or nitrothinner C-6000. Only non-hardened putty can be cleaned.

STORAGE

It is necessary to ensure the temperature from +5°C to + 25°C and avoid direct solar radiation during storage and transport. Dash of the resin on the surface of putty is acceptable. We guarantee shelf life and quality of the product for 12 months.

PACKAGING

Resin: 1 l, 5 l – a can Repair box: 0,25 kg of resin – a can + 0,2 m2 of glass texture under the plastic cap

COLOUR

Light yellow transparent liquid

BACK TO LIST Page 28

TECHNICAL DATA SHEET

POLYKAR ST technical description: 10. 10. 2012 DESCRIPTION AND USAGE

ST is a two-component spray putty intended for unification of surface between filled and no filled places, or for straightening of surface on car bodies. It is used for formation of equable layer of putty on whole car body, which is necessary before application of filler and subsequently upper paint. After hardening ST provides equable layer, which is easily sand able and also stays hard, tough, resistant to bend, stroke and vibrations. Also suitable for surfaces of hardwood and MDF-boards.

ENVIRONMENT

The putty must not be used for filling places which are in direct contact with food and drinking water.

VOC VOLUME

VOC = 220 g / l This product complies with EU Directive (2004/42/EC), which gives for the preparation of this category (B / b) the limit value of volatile matter content of 250 g / l in finished product.

APPLICATION

Get rid of rust and abrade the bonded surface by sandpaper P80. Surface must be clean, dry and free of dust and grease. For maximum corrosion protection use epoxy or polyurethane basecoat. Do not apply the putty on reactive, single or nitrocellulose basecoats.

For application we recommend to use the nozzle 1,8-3,0 mm and the air pressure 0,40,6 MPa. Spray putty can forms dry layer in thickness up to 1000 µm. We recommend to use the thinner THINNER POLYESTER for modification of consistence before usage.

Stir the content of the can well before usage!

HARDENING

The putty is hardened with hardener (INICIÁTOR 40, transparent liquid) in weight ratio: - 100 parts of putty : 5 parts of hardener – recommended ratio for temperature 23°C The mixture must be homogenized perfectly and filtered.

POT LIFE

The putty is necessary to be used within 40 minutes after mixing with hardener at temperature 23°C and hardening ratio 100:5. Adjusting of the hardening ratio can partly eliminate the influence of temperature on the potlife. At lower temperatures (at least 17°C), the potlife increases, at higher temperatures is reduced. Do not exceed the recommended hardening ratio.

SANDING

The putty is dry against dust after 60 minutes and sand able after 120 minutes at temperature 23°C and hardening ratio 100:5. This time can be shortened by baking at temperature around 60°C. Dry sanding starts with sanding paper P80 and finishes with sanding paper P120-180. Wet sanding starts with sanding paper P120 and finishes with sanding paper P180-220. We recommend use the rotary or vibratory grinding machine.

UPPER COATINGS

It is possible to use all common paint systems on the putty. The putty withstands temperatures of 80-110 °C.

TOOLS CLEANING

Dirty parts of tools for filling can be cleaned with THINNER POLYESTER or nitrothinner C-6000. Only non-hardened putty can be cleaned.

STORAGE

It is necessary to ensure the temperature from +5°C to + 25°C and avoid direct solar radiation during storage and transport. Dash of the resin on the surface of putty is acceptable. We guarantee shelf life and quality of the product for 12 months.

PACKAGING

- 1 kg, 4 kg, 15 kg – a can

COLOUR

White / gray

BACK TO LIST Page 29

TECHNICAL DATA SHEET POLYKAR FILLER 4:1 PREMIUM technical description: 10. 10. 2012 DESCRIPTION AND USAGE

FILLER 4:1 PREMIUM is a high quality two-component acryl-urethane filler for car repair and industry. It has a high solid content, excellent flow properties, good stability when applied to vertical surfaces and high filling power. Cures rapidly in larger layers, perfectly sandable. It is an ideal base to ensure a high quality look of painted objects.

FILLER 4:1 PREMIUM finds wide usage in coating systems for coating fleet Railways, urban transportation and various engineering products.

SURFACE

ADHESION

steel

excellent

aluminum (pretreatment required)

excellent

hardwood, concrete

good

plastics (pretreatment required)

good

BKP putties

excellent

laminate

excellent

old coatings

excellent

ENVIRONMENT

The must not be used for filling places which are in direct contact with food and drinking water.

VOC VOLUME

VOC = 527 g / l This product complies with EU Directive (2004/42/EC), which gives for the preparation of this category (B /c) the limit value of volatile matter content of 540 g / l in finished product even after dilution in the recommended ratio.

APPLICATION

Surface after filling sand with sandpaper P220-240 and perfectly degrease. It is applicated separately in 2-3 layers (40-60 µm). Each layer must be leaved to draught about 5-10 minutes.

Filling system – thin by THINNER POLYURETAN (max. 10%) Working viscosity: 4/20°C. circa 19 s Nozzle of spray gun:  1.5 - 1.8 mm Air pressure: 0,3 - 0,4 MPa 1 liter of filler covers about 3,2 m2 in thickness of layer 100 µm.

COVERAGE HARDENING

The filler is hardened with hardener TVRDIDLO 1:4 PREMIUM in volume ratio 4:1 - 4 parts of filler : 1 part of hardener.

The mixture must be homogenized perfectly and filtered.

POT LIFE

The filler is necessary to be used within 45 minutes after mixing with hardener at temperature 20°C and hardening ratio 4:1.

SANDING

The filler is sandable after 3 hours at temperature 23°C and thickness of dry layer 150 µm, after 30-40 minutes at temperature 60°C. Dry sanding is done with sanding paper P400-800. Wet sanding is done with sanding paper P600-1000.

UPPER COATINGS

It is possible to use all common paint systems on the filler. The filler withstands temperatures of 80-110 °C.

TOOLS CLEANING

Dirty parts of tools for filling can be cleaned with THINNER POLYURETAN or nitrothinner C-6000. Only non-hardened filler can be cleaned.

STORAGE

It is necessary to ensure the temperature from +5°C to + 25°C and avoid direct solar radiation during storage and transport. Store in a cool and dry place. We guarantee shelf life and quality of the product for 12 months.

PACKAGING

- filler 1 l + 0,25 l hardener – a can - filler 4 l + 1 l hardener – a can

COLOUR

Gray / black

BACK TO LIST Page 30

TECHNICAL DATA SHEET POLYKAR FILLER 4:1 NORMAL technical description: 10. 10. 2012 DESCRIPTION AND USAGE

FILLER 4:1 NORMAL is a quality two-component acrylic filler for car repair and industry. It has good filling properties and excellent flow properties. Cures rapidly also in larger layers and is perfectly sandable. It is an ideal base to ensure a high quality look of painted objects.

SURFACE

ADHESION

steel

excellent

aluminum (pretreatment required)

excellent

hardwood, concrete

good

plastics (pretreatment required)

good

BKP putties

excellent

laminate

excellent

old coatings

excellent

ENVIRONMENT

The filler must not be used for filling places which are in direct contact with food and drinking water.

VOC VOLUME

VOC = 465 g / l This product complies with EU Directive (2004/42/EC), which gives for the preparation of this category (B /c) the limit value of volatile matter content of 540 g / l in finished product even after dilution in the recommended ratio.

APPLICATION

Surface after filling sand with sandpaper P220-240 and perfectly degrease. It is applicated separately in 2-3 layers (40-60 µm). Each layer must be leaved to draught about 5-10 minutes.

Filling system – thin by THINNER ACRYL (max. 10%) Working viscosity: 4/20°C. circa 22 s Nozzle of spray gun:  1.5 - 1.8 mm Air pressure: 0,3 - 0,4 MPa

COVERAGE

1 liter of filler covers about 5,6 m2 in thickness of layer 100 µm.

HARDENING

The filler is hardened with hardener TVRDIDLO 1:4 NORMAL/PLUS in volume ratio 4:1 - 4 parts of filler : 1 part of hardener.

The mixture must be homogenized perfectly and filtered.

POT LIFE

The filler is necessary to be used within 60 minutes after mixing with hardener at temperature 20°C and hardening ratio 4:1.

SANDING

The filler is sandable after 3 hours at temperature 23°C, after 30-40 minutes at temperature 60°C. Dry sanding is done with sanding paper P400-800. Wet sanding is done with sanding paper P600-1000.

UPPER COATINGS

It is possible to use all common paint systems on the filler. The filler withstands temperatures of 80-110 °C.

TOOLS CLEANING

Dirty parts of tools for filling can be cleaned with THINNER ACRYL or nitrothinner C6000. Only non-hardened filler can be cleaned.

STORAGE

It is necessary to ensure the temperature from +5°C to + 25°C and avoid direct solar radiation during storage and transport. Store in a cool and dry place. We guarantee shelf life and quality of the product for 12 months.

PACKAGING

- filler 1 l + 0,25 l hardener – a can - filler 4 l + 1 l hardener – a can

COLOUR

White / gray / black

BACK TO LIST Page 31

TECHNICAL DATA SHEET

POLYKAR FILLER 1K technical description: 10. 10. 2012 DESCRIPTION AND USAGE

FILLER 1K is a quality one-component acrylic filler for car repair and industry. It has very good filling properties and excellent adhesion. Cures in air, is resistant to weathering and chemical action. Well sandable, is simple to use. It is an ideal base to ensure a high quality look of painted objects.

SURFACE

ADHESION

steel

excellent

aluminum (pretreatment required)

excellent

hardwood, concrete plastics (pretreatment required)

good good

BKP putties

excellent

laminate

excellent

old coatings

excellent

ENVIRONMENT

The filler must not be used for filling places which are in direct contact with food and drinking water.

VOC VOLUME

VOC = 533 g / l This product complies with EU Directive (2004/42/EC), which gives for the preparation of this category (B /c) the limit value of volatile matter content of 540 g / l in finished product even after dilution in the recommended ratio.

APPLICATION

Surface after filling sand with sandpaper P220-240 and perfectly degrease. It is applicated separately in 2-3 layers (40-60 µm). Each layer must be leaved to draught about 5-10 minutes.

Filling system – thin by FILLER ACRYL (max. 10%) Working viscosity: 4/20°C. circa 25 s Nozzle of spray gun:  1.4 - 1.6 mm Air pressure: 0,3 - 0,4 MPa

COVERAGE

1 liter of filler covers about 10 m2 in thickness of layer 40 µm.

HARDENING

As one component does not require a hardener.

SANDING

The filler is sandable after 45-60 minutes at temperature 23°C, after 15 minutes at temperature 60°C. Dry sanding is done with sanding paper P400-800. Wet sanding is done with sanding paper P600-1000.

UPPER COATINGS

It is possible to use all common paint systems on the filler.

TOOLS CLEANING

Dirty parts of tools for filling can be cleaned with THINNER ACRYL or nitrothinner C6000. Only non-hardened filler can be cleaned.

STORAGE

It is necessary to ensure the temperature from +5°C to + 25°C and avoid direct solar radiation during storage and transport. Store in a cool and dry place. We guarantee shelf life and quality of the product for 12 months.

PACKAGING

- 0,8, 5 l – a can

COLOUR

Beige

BACK TO LIST Page 32

TECHNICAL DATA SHEET

POLYKAR THINNER ACRYL technical description: 10. 10. 2012

DESCRIPTION AND USAGE

THINNER ACRYL is a high quality acrylic thinner, which is used for modification of consistence of acrylic fillers and clearcoats. It is suitable into all acrylic coating compositions.

ENVIRONMENT

THINNER ACRYL must not be used for filling places which are in direct contact with food and drinking water.

STORAGE

It is necessary to ensure the temperature +5°C - +20°C and avoid direct solar radiation during storage and transport. Store in dry and cold place.

We guarantee shelf life and quality of the product for 12 months.

PACKAGING

- 1,0 l – can - 5,0 l - canister

COLOUR

Transparent

BACK TO LIST Page 33

TECHNICAL DATA SHEET POLYKAR THINNER POLYESTER technical description: 10. 10. 2012

DESCRIPTION AND USAGE

THINNER POLYESTER is thinner, which is used for thinning of two-component polyester spray putties. It is suitable also for cleaning of working tools polluted by all types of polyester putties.

ENVIRONMENT

THINNER POLYESTER must not be used for filling places which are in direct contact with food and drinking water.

STORAGE

It is necessary to ensure the temperature +5°C - +20°C and avoid direct solar radiation during storage and transport. Store in dry and cold place.

We guarantee shelf life and quality of the product for 12 months.

PACKAGING

- 1,0 l – can - 5,0 l - canister

COLOUR

Transparent

BACK TO LIST Page 34

TECHNICAL DATA SHEET POLYKAR THINNER POLYURETAN technical description: 10. 10. 2012

DESCRIPTION AND USAGE

THINNER POLYURETAN is a thinner, which is used for adjusting the consistency of fillers POLYKAR FILLER 4:1 PREMIUM and POLYKAR FILLER 2K PUR. It is suitable also for thinning acrylic paints and cleaning of working tools polluted by all types of polyurethane coatings.

ENVIRONMENT

THINNER POLYURETAN must not be used for filling places which are in direct contact with food and drinking water.

STORAGE

It is necessary to ensure the temperature +5°C - +20°C and avoid direct solar radiation during storage and transport. Store in dry and cold place.

We guarantee shelf life and quality of the product for 12 months.

PACKAGING

- 1,0 l – can - 5,0 l - canister

COLOUR

Transparent

BACK TO LIST Page 35

TECHNICAL DATA SHEET

TOPEKOR technical description: 10. 10. 2012

DESCRIPTION AND USAGE

TOPEKOR contains effective preparation for dispersion of anorganic and organic sediments, and inhibitor which protect against corrosion in closed systems of central heating. TOPEKOR can be used also in circulating systems where is the possibility of formation of scale or corrosion.

MECHANISM AND TIME OF EFFICIENCY

Anticorrosive effects of TOPEKOR are based on formation of molecular layer, which avoid access of oxygen (which is dissolved in heating medium) to the surface of heating tube. Prevent sedimentation effect is based on slow chemical dissolving of sediments in slightly acid environment. The time of TOPEKOR treatment is not exactly limited, because dissolving of harder sediments (mainly in older systems) goes slowly and in the long term. Function of TOPEKOR in central heating system shows itself in better control over regulation valves and advanced efficiency of furnace.

DOSAGE

Content of the container (500 ml) guarantee perfect protection of system with capacity up to 400 litres of water during minimally two years. TOPEKOR fundamentally improves heating efficiency of system thanks to removing of scale and enlarges its shelf life with limitation of corrosion. TOPEKOR should be dosed into circulating system in the beginning of heating season to obtain perfect shuffle by the water circulation. Content of the container must be shaked before usage and then filled into the heating system. Changing of the water is not necessary. Dosage should be done in rubber gloves.

In case of protection of old systems highly polluted with scale, where the protection hasn´t been done before, we recommend to drain the system off and fill again with new dose of TOPEKOR after further 2 months, when the bigger sediments are dissolved.

ELECTROCHEMICAL STABILITY

The preparation TOPEKOR doesn´t advanced the conductivity of heating medium and also does not implement ions inside, which should influence electrochemical balance of the system. This is fundamental difference against common anticorrosive preparatives.

COMPATABILITY WITH MATERIALS

TOPEKOR does not work aggresively on common materials as: iron, steel, cast iron, zinc coating, copper, polyethylene, polypropylene, rubber, sealing rubbers, teflon. It gets on glycols in water antifreezing systems.

ENVIRONMENT

TOPEKOR is ecological, biodegradable preparation. Draining of the central heating system into canalization has no harmful influence on environment.

STORAGE AND PACKAGING

Protect against freezing temperatures. We guarantee shelf life and quality of the product for 24 months.

Packaging: - 500ml – plastic container (different container according to agreement)

BACK TO LIST Page 36

We look forward to our cooperation! www.bkp.cz

CLICK TO CLOSE