ID5101 QIG 2011-0721_zw

Installing Procedures 1. Screw the Back Plate on the wall.

Please pull out the AC wires and Ethernet cable pass through the back plate. Then, connect them with the Video Indoor Station after securing the Back Plate on the wall.

If necessary, please connect the Earth wire to the screw as diagram below.

For more GPIO application, please refer to Safety/Security Application in next page

2. Connect the AC (Universal 100~240VAC) wires and Ethernet cable.

Package Contents

Plug the AC cable connector of ID5101 to Power-Connecting connector, and connect Ethernet cable to ID5101 as diagram below.

These items are included in your Video Indoor Station package. Check this list before installation to ensure that you have received all items.

Be careful when you are connecting the AC wires, please check the AC condition and turn off the general power switch before you start to connect the wires.

1. Video Indoor Station 2. Back Plate 3. Wall mounted screw pack 4. Screw Pack (2 pieces of M4 x 10 mm) 5. Screw for Earth Wire 6. Wrench 7. H type Terminal Connector for Power Wire (2 pieces) 8. Adapter 9. I/O Cable (3 pieces) 10. Relay Board (2 pieces) (Accessories are put in the paper tube of box) Please contact your dealer immediately if any item(s) is missing.

Package Contents

Rear Panel & GPIO Connectors 3. Screw the Video Indoor Station with Back Plate.

After connecting the wires and cables properly, then screw the 2 screws that come with the package into the front panel. Please double check all the installation procedures again, then you may power on the general power switch to start the configuration procedures.

Rear Panel and Connectors

Before connecting to Safety and Security Devices

NOTE: To avoid electrical shock, we strongly suggest that connecting AC power to ID5101 after ID5101 has installed on the wall.

GPIO connectors and I/O Pin Assignment and Wire Color There are three GPIO connectors on the rear panel of your Video Indoor Station.

Installing Video Indoor Station These GPIO connectors are used to connect with Safety and Security devices.

Before you begin to connect other devices to the ID5101, the I/O wires and their colors for GPIO connectors are illustrated as pictures below.

Due to the view angle of the camera is limited, therefore the installation position for Video Indoor Station is crucial. In order to get a better view, the view angle of this door phone should be around 105. Also the height of the lens position is suggested between 155 cm to 165 cm according to building conditions.

Please reserve the space for junction wiring in the wall, you may refer to the embedded box dimension as diagram below.

GPIO connectors and I/O Pin Assignment and Wire Color Installation Example

800-0000007-00-00

1

IO Circuit and Application

Wire connection for Alarm

The ID5101, Video Indoor Station, provides 8 Input ports and 4 Output port for your house to set up Home Safety and Security; you may refer the following examples for each application.

Please connect the adapter which comes with the package to the AC line as below and then connect your end devices according to your requirement.

Magnetic Switches Both diagram and photo of Magnetic Switch installation show you how to use the second GPIO connector to connect with Magnetic Switches, and you can connect up to four magnetic switches accordingly based on the diagram or photo.

Connect to AC line and Adapter

LIGHTING The illustration (diagram) shows you how to use the first GPIO connector and wire to connect Adapter and two Relay Boards for Lighting Control.

Wire connection for MS (Magnetic Switches)

NOTE: The second GPIO connector is used to connect up to four Magnetic Switches.

Wire connection for Lighting

CO Detector, Emergency Button and Gas Detector The status of the following safety devices will be shown on the main screen. The following diagrams show you how to use 3rd GPIO connector to connect CO Sensor, Emergency Button, and Gas Detector.

ALARM The illustration (diagram) shows you how to use the first GPIO connector and wire to connect AC power, Adapter and Relay Board for ALARM device.

Wire connection for Alarm

NOTE: Please use wire tape to seal unused wire to isolate the wire.

800-0000007-00-00

2

A. DHCP Client: The system will automatically assign you an IP address.

B. Static IP: you have to input IP address, Subnet Mask, Default Gateway, Primary DNS and Secondary DNS data.

C. PPPoE: This allows you to set Internet connection with User Name and Password.

Save

Click this button to save your setting.

SIP Setting Wire connection for CO, Gas detector, and Emergency Button NOTE: The 3rd GPIO connector is used to connect CO Sensor, Emergency Button, and Gas Detector.

There are two ways to configure ID5101. One is “Configure via Web UI”, the other is “Configure on ID5101”.

Configure via Web UI This section describes how to configure your ID5101 with Web User Interface. This UI also provide remote management capability to service provider.

SIP Setting page

Input IP address of your ID5101

Item

Description Authentication

NOTE 1: To obtain IP address of your ID5101.

Select Setting soft-function key Network Setting on your ID5101 (with password: default:1234) IP Address And you will find IP address of the ID5101 on the network.

Display Name

This name will show on the IP phone of called parties. You can fill in the preferred name here.

For example, 807

User Number

You may fill in the phone number here, normally it is provided by service provider. To work with IP PBX, you may fill in extension number. For example, 807

Account ID

You may fill in your account name of SIP service in this field.

For example, 807

Account Password

You may fill in the password of your SIP service account.

For example, 807 SIP Proxy Server

Service

NOTE 2: The default ID and password for system login are “admin” and “admin”.

You may select “Enable” or “Disable” the SIP Proxy Server in the dropdown menu.

NOTE: For Peer-to-Peer mode, user needs to select Disable in the dropdown menu.

IP Address

You may fill in the IP address of SIP Proxy Server in this field.

SIP Registrar Server

Login ID5101 Web UI

IP Address

You may fill in the IP address of SIP Registrar Server here.

Registration Expire Time

The default is 3600 seconds.

Protocol

You may select network communication protocol of the SIP service here. There are 2 options: UDP and TCP. Default setting is UDP protocol.

Hold Version

This setting is configured differently depending on which SIP proxy server is being connected. The SIP proxy server may support generally two type of call hold, RFC2543 and RFC3264.

Session Timer

You can set the session timer here. The range is from 0 to 1800 seconds.

Default is 0 second.

Media Timer

This setting allows your phone to force release automatically a conversational call when your phone doesn't receive any media packets from the remote side during a period of time. If you want to disable this feature, please fill in "0" sec.

SIP TOS

You may enable Tag-of-Service of SIP protocol here.

RTP TOS

You may enable Tag-of-Service of RTP protocol here.

Save

Click this button to save your setting.

Network Setting NOTE: After Log in Web UI, Language on the first page allows you to select language “English” or “Traditional Chinese” and let the language be displayed on your ID5101 GUI.

Safety & Security – Device setting Item

Description

MAC Address

This is a quasi-unique identifier attached to most network adapters.

This webpage is used to configure Safety and Security devices.

There are 8 Input ports (DI1~DI8) and 4 Output ports (DO1~DO4) available on ID5101 GPIO module.

Moreover, DI1-DI4 are for MS (Magnetic Sensors), DI5-DI8 are for CO sensor, Emergency Button, and Gas detector (DI8 is reserved).

DO1-DO3 are for Lighting, Lighting, Alarm. (DO4 is reserved).

IP Type The default value is DHCP Client.

There are three options: DHCP Client, Static IP and PPPoE. 800-0000007-00-00

3

operators. You will see last 2 items for PPPoE are grayed out.

PPPoE - This selection is for connecting ADSL modem directly. Your phone will trigger ADSL model to connect to Internet automatically when you are dialing phone number.

IP Address

You may fill in IP address here if Static IP is selected.

Subnet Mask

You may fill in Subnet Mask address here if Static IP is selected.

Default Gateway

You may fill in default gateway address here if Static IP is selected.

Primary DNS

You may fill in primary DNS server address here if Static IP is selected.

Secondary DNS

You may fill in secondary DNS server address here if Static IP is selected.

PPPoE Account

You may fill in PPPoE account ID or name here if PPPoE is selected in IP type selection.

PPPoE Password

You may fill in PPPoE account password here if PPPoE is selected in IP type selection.

Web UI

This item allows you enable or disable the Web-User-Interface HTTP service. Web UI will be not available if disabled.

ICMS IP

The IP address of ICMS (Intelligent Community Management Server).

NOTE: Your ID5101 needs to be connected to AmRoad ICMS system.

ICMS Port

The IP port number of ICMS (Intelligent Community Management Server).

NOTE: Your ID5101 needs to be connected to AmRoad ICMS system.

Device Setting page

ITEM

Description

Device Name

In the drop-down menu, select the device name that your ID5101’s GPIO port is connected to.

Triggered by

For 8 Input ports only, user may select “Positive” or “Negative”.

NOTE: This means user can define the light status (Green or Red) on your ID5101 Safety Sub-menu.

En/Disable

Select “Enable” or “Disable” User may select “Disable” when the ID5101’s GPIO port is not connected to any device.

NOTE: If user doesn’t install some safety device, we suggest SI select “Disable” so that the safety device will be displayed as gray light on ID5101.

SIP Setting Configure on ID5101

This setting allows you to se up necessary parameters of SIP services and it is password protected. Default password is “1234”. You may change password by using Chg Password soft-function key.

This section describes how to set up your Video Indoor Station. You may press Setting soft-function key to enter this Setting page. There are 8 major items for configuration: You may use [ ] and [ ] keys to select preferred item, and then press Enter key [ ] or press Enter soft-function key to take further actions.

ITEM

Description

Phone Number

The phone number of your ID5101. Normally it is provided by service provider. You can also set an extension number here if connecting to an IP PBX.

Display Name

Initial of Display Name. This name will show on the IP phone of called parties. You may fill in the preferred name here.

Account

You may fill in your account name of SIP service here.

Password

You may fill in the password of your SIP service account here.

Mode

This item allows you to select the working model of SIP service. Select “Server Mode” mode if this phone is connected to a SIP server or IP PBX. Default setting is “Peer-to-Peer Mode”.

Protocol

You may select the correct low level communication protocol here. There are 2 options: UDP and TCP. You have to confirm which one the service is using from your service provider. Default setting is UDP.

SIP Proxy

You may fill in IP address or domain name of the SIP Proxy Server here.

SIP Registrar

You may fill in IP address or domain name of SIP Registrar Server here.

SIP Expire

Initial of Registration Time. This item is a parameter of SIP service. You may fill in the effective registration period of SIP service here. You have to contact your service provider to get correct setting. Default setting is 3600 seconds.

SIP Sess Timer

Initial of Session Timer. This is a parameter of SIP service.

You may fill in the Session Timer period of SIP service. You have to contact your service provider to get correct setting.

Default setting is 0 seconds.

Press Setting soft-function key to enter Setting page NOTE: 1. Network Setting, SIP Setting, Stream Setting, and Service Setting are protected by password. (Default password: 1234) 2. This setting password is different from Security password.

Network Setting This Network Setting allows you to set up the important parameters of network connection, and it is protected by password.

NOTE: You need to enter password to enter “Network Setting”. Default password is “1234”. You may change password by using Chg Password soft-function key.

The screen after entering Network Setting page NOTE: For more detailed information, the setting of Video Indoor Station and the Web UI ITEM

Description

Net Type

This item allows you to select type of IP address of this device. There are 3 options DHCP, Static IP and PPPoE, the default is DCHP.

DHCP - If you wish to connect this device to an exist network and get dynamic IP address from the DHCP server, please select this one. You will see all other items in this mode are grayed out. In most of cases, DHCP Client is used for connecting LAN (Local-Area-Network).

Static IP - If you wish to use Static IP address to connect to network, you may select this one. You may get Static IP when you applying SIP service from carriers or

800-0000007-00-00

Extra NOTE NOTE 1: To open the door by pressing the “ # ” keypad on ID5101 Video Indoor Station, the door must have been installed “Electrical-door Lock”.

NOTE 2: ID5101 RFID Internal Module, ISO 14443A Compliant/ 13.56 MHz RFID Mifare.

4