Albany Technical Data Sheets by Brewers

Contents

ALBANY ACRYLIC EGGSHELL

ALBANY ACRYLIC GLOSS

13 ALBANY ACRYLIC PRIMER UNDERCOAT

15 ALBANY ALL PURPOSE PRIMER

19 ALBANY ALUMINIUM WOOD PRIMER

21 ALBANY DURABLE MATT EMULSION

23 ALBANY FUNGICIDAL WASH

25 ALBANY GLOSS

29 ALBANY HIGH OPACITY SUPERCOVER

31 ALBANY METAL PRIMER

33 ALBANY NON DRIP GLOSS

37 ALBANY POLYURETHANE EGGSHELL VARNISH

39 ALBANY POLYURETHANE GLOSS VARNISH

Contents

41 ALBANY POLYURETHANE MATT VARNISH

43 ALBANY PRIMER SEALER

45 ALBANY RED OXIDE PRIMER

47 ALBANY SMOOTH DURABLE EGGSHELL

49 ALBANY SMOOTH MASONRY PAINT

51 ALBANY SOFT SHEEN EMULSION

53 ALBANY STABILISING SOLUTION

55 ALBANY UNDERCOAT

59 ALBANY VINYL MATT EMULSION

61 ALBANY VINYL SILK EMULSION

63 ALBANY WOOD PRIMER

65 ALBANY YACHT VARNISH

Technical Data Sheet

ALBANY ACRYLIC EGGSHELL An attractive mid sheen waterborne formulation for interior use. Durable and washable.

AVAILABILITY Colour Range

See Albany Literature.

Packaging

1, 2.5 and 5 litre.

PROPERTIES Drying Time

Under normal drying conditions touch dry 1-2 hours and recoatable after 6 hours. Allow for adequate ventilation during the drying period.

Finish

Mid sheen.

Composition

Pigment: Titanium Dioxide, coloured pigments and extenders Binder: Acrylic polymer Solvent: Water

Spreading Rate

Up to 15m² per litre on smooth surfaces.

Wet Film Thickness

66 micrometres at 15m² per litre.

Dry Film Thickness

24.42 micrometres at 15m² per litre.

Volume Solids

36% White. Other colours will vary.

Flash Point

Not applicable.

VOC Content

EU limit value for this product (cat.A/b): 150 g/l (2007) / 130 g/l (2010) This product contains max. 46 g/l VOC.

Limitations

For interior use only. Do not apply when air or substrate temperatures are likely to fall below 8ºC or when the relative humidity is above 80% during application or the drying period.

PREPARATION New Surfaces Walls

All surfaces must be sound, clean, suitably dry and free from anything that will interfere with the adhesion of the materials to be applied. Powdery, polished plaster or dense surfaces should be primed with Albany Primer Sealer. Porous surfaces should be ‘mist’ coated with Albany Acrylic Primer Undercoat thinned with up to 10% clean water.

Timber

All surfaces must be suitably dry, and free from anything that will interfere with the adhesion of the materials to be applied. Rub down with a suitable grade of abrasive paper. Remove all dust. Treat knots with two thin coats of fresh knotting. Fill any fixing holes, open joints and shallow surface defects with a suitable proprietary filler. Rub down with a suitable grade of abrasive paper. Remove all dust. Prime with one coat of Albany Acrylic Primer Undercoat.

Technical Data Sheet

All Metals Including Galvanised

Additional Surface Preparation - All Metals Non-ferrous Metals

Lightly abrade to a bright (not polished) surface - excluding galvanised surfaces. Rinse thoroughly with clean water to remove all resides. Allow to dry. Prime with one coat of Albany All Purpose Primer.

Ferrous Metals

Remove all millscale and rust back to clean metal. Remove all residues. Prime within the working day with one coat of Albany All Purpose Primer.

Previously Decorated Surfaces Walls

Timber

All surfaces must be suitably dry, and free from anything that will interfere with the adhesion of the materials to be applied. Remove all loose, and failing or suspect paint. Remove grey and denatured surfaces by rubbing down with abrasive paper. Feather edges of sound paint. Remove all dust. Organic growth must be removed and the areas treated with Albany Fungicidal Wash. Treat knots with two thin coats of fresh knotting. Fill any fixing holes, open joints and shallow surface defects with a suitable proprietary filler. Rub down with a suitable grade of abrasive paper. Remove all dust. Spot prime bare and filled areas with one coat of Albany Acrylic Primer Undercoat.

Metals

Walls, Timber and Metals

Wash remaining sound paint with hot water and liquid detergent solution to remove any contaminants, frequently changing the water. Any glossy or eggshell surfaces must be wet abraded to provide a key. Rinse with clean water to remove all residues. Allow to dry. Bring forward patch primed and or spot primed areas with Albany Acrylic Eggshell.

Technical Data Sheet

COATING SYSTEM

Apply one or two coats as required.

APPLICATION

Stir well before use. For walls apply using a good quality fine filament synthetic brush or medium pile woven roller. For airless spray (dilution may be required). For further information contact the Akzo Nobel Customer Advice Centre. For joinery apply using a good quality fine filament synthetic brush.

CLEANING

Wash with clean water immediately after use

HEALTH AND SAFETY

Please refer to the Safety, Health and Environmental Information on the container. Take special precautions during the surface preparation of pre 1960â&#x20AC;&#x2122;s painted surfaces as they may contain harmful lead. For further information contact Brewers. When preparing all surfaces avoid the inhalation of dust and/or metal particles. Wear a suitable facemask. Material Safety Data Sheets for this and all other Albany products are freely available from the place of purchase or the address below. Store in secure dry conditions inaccessible to children or animals. Containers should be kept closed during storage. Do not empty into drains, watercourses or access routes to septic tanks.

GENERAL INFORMATION

Apply all products in accordance with BS 6150: 2006 Code of practice for painting of buildings and BS 8000: Part 12: 1989 Code of practice for decorative wallcoverings and painting. Under normal and frost free conditions this product will remain usable for up to two years if stored correctly and unopened. Every care is taken to ensure that all information provided on this Technical Data Sheet is accurate. Brewers are unable to guarantee results as it has no control over the conditions under which its products are applied.

Before using this product please ensure you have the latest information. For help or more information contact: Brewers Tel 01323 411080 E-mail enquiries@brewers.co.uk Website www.brewers.co.uk This information is correct at date of issue November 2009.

Albany House Ashford Road Eastbourne BN21 3TR Tel 01323 411080 Fax 01323 721435 E-mail: enquiries@brewers.co.uk Website: www.brewers.co.uk 7

Technical Data Sheet

ALBANY ACRYLIC GLOSS An attractive mid sheen waterborne formulation for interior and extrerior use. Durable and washable.

AVAILABILITY Colour Range

See Albany Literature.

Packaging

1 & 2.5 litres.

PROPERTIES Drying Time

Under normal drying conditions touch dry 1-2 hours and recoatable after 6 hours. Allow for adequate ventilation during the drying period.

Finish

Satin Gloss.

Composition

Pigment: Titanium Dioxide, coloured pigments and extenders Binder: Acrylic polymer Solvent: Water

Spreading Rate

up to 13m² per litre on smooth surfaces.

Wet Film Thickness

77 micrometres at 13m² per litre.

Dry Film Thickness

30.05 micrometres at 13m² per litre.

Volume Solids

39% White. Other colours will vary.

Flash Point

Not applicable.

VOC Content

EU limit value for this product (cat.A/d): 150 g/l (2007) / 130 g/l (2010) This product contains max. 49 g/l VOC.

Limitations

Do not apply when air or substrate temperatures are likely to fall below 8ºC or when the relative humidity is above 80% during application or the drying period. Do not use over paints containing aluminium or zinc pigments.

PREPARATION New Surfaces Walls

Timber

Technical Data Sheet

All Metals Including Galvanised

Additional Surface Preparation - All Metals Non-ferrous Metals

Ferrous Metals

Remove all millscale and rust back to clean metal. Remove all residues. Prime within the working day with one coat of Albany All Purpose Primer.

Previously Decorated Surfaces Walls

Timber

All surfaces must be suitably dry, and free from anything that will interfere with the adhesion of the materials to be applied. Remove all loose, and failing or suspect paint. Remove grey and denatured surfaces by rubbing down with abrasive paper. Feather edges of sound paint. Remove all dust. Organic growth must be removed and the areas treated with Albany Fungicidal Wash. Treat knots with two thin coats of fresh knotting. Fill any fixing holes, open joints and shallow surface defects with a suitable proprietary filler. Rub down with a suitable grade of abrasive paper. Remove all dust. Spot prime bare and filled areas with one coat of Albany Acrylic Primer Undercoat.

Metals

Walls, Timber and Metals Wash remaining sound paint with hot water and liquid detergent solution to remove any contaminants, frequently changing the water. Any glossy or eggshell surfaces must be wet abraded to provide a key. Rinse with clean water to remove all residues. Allow to dry. Bring forward patch primed and or spot primed areas with Albany Acrylic Gloss.

Technical Data Sheet

COATING SYSTEM

Apply one or two coats as required.

APPLICATION

Stir well before use. For walls apply using a good quality fine filament synthetic brush or medium pile woven roller. For airless spray application dilution may be required. For joinery apply using a good quality fine filament synthetic brush.

CLEANING

Wash with clean water immediately after use.

HEALTH AND SAFETY

GENERAL INFORMATION

Apply all products in accordance with BS 6150: 2006 Code of practice for painting of buildings and BS 8000: Part 12: 1989 Code of practice for decorative wallcoverings and painting. Under normal and frost free conditions this product will remain usable for up to two years if stored correctly and unopened. Every care is taken to ensure that all in formation provided on this Technical Data Sheet is accurate. Brewers are unable to guarantee results as it has no control over the conditions under which its products are applied.

Albany House Ashford Road Eastbourne BN21 3TR Tel 01323 411080 Fax 01323 721435 E-mail: enquiries@brewers.co.uk Website: www.brewers.co.uk 11

Technical Data Sheet

ALBANY ACRYLIC PRIMER UNDERCOAT Versatile formulation for priming / undercoating timber and dry plaster.

AVAILABILITY Colour Range

White.

Packaging

1, 2.5 and 5 litres.

PROPERTIES Drying Time

Under normal drying conditions touch dry in 30 minutes and recoatable after 4 hours. Allow for adequate ventilation during the drying period.

Finish

Matt.

Composition

Pigment: Titanium Dioxide and extenders Binder: Acrylic polymer Solvent: Water

Spreading Rate

Up to 16m² per litre on smooth surfaces.

Wet Film Thickness

62 micrometres at 16m² per litre.

Dry Film Thickness

22 micrometres at 16m² per litre.

Volume Solids

35%.

Flash Point

Not applicable.

VOC Content

EU limit value for this product (cat.A/d): 150 g/l (2007) / 130 g/l (2010) This product contains max. 6 g/l VOC.

Limitations

For interior and exterior use. Do not apply when there is a risk of rain, air or substrate temperatures are likely to fall below 8ºC or when the relative humidity is above 80% during application or the drying period.

PREPARATION New Surfaces

Previously Decorated Surfaces

All surfaces must be suitably dry, and free from anything that will interfere with the adhesion of the materials to be applied. Rub down with a suitable grade of abrasive paper. Remove all dust. Timber with oils/extractives must be swabbed with clean dearo matised white spirit, frequently changing the face of the cloths. Treat knots with two thin coats of fresh knotting. Fill any fixing holes, open joints and shallow surface defects with a suitable proprietary filler. Rub down with a suitable grade of abrasive paper. Remove all dust.

Technical Data Sheet

COATING SYSTEM

Apply one or two coats as required.

APPLICATION

Stir well before use. Apply using a good quality fine filament synthetic brush to an even thickness. Lay off in the direction of the grain. Can also be applied by roller, airless or conventional spray.

CLEANING

Return surplus material to container. Wash with clean water immediately after use.

MAINTENANCE INFORMATION FOR CDM FILE

HEALTH AND SAFETY

GENERAL INFORMATION

Between maintenance redecoration surfaces may be washed with a warm water and liquid detergent solution to remove surface dirt.

Albany House Ashford Road Eastbourne BN21 3TR Tel 01323 411080 Fax 01323 721435 E-mail: enquiries@brewers.co.uk Website: www.brewers.co.uk 14

Technical Data Sheet

ALBANY ALL PURPOSE PRIMER A versatile primer for many surfaces.

AVAILABILITY Colour Range

Beige.

Packaging

500ml, 1, 2.5 and 5 litres.

PROPERTIES Drying Time

Under normal drying conditions surface dry 6-8 hours and recoatable after 16 hours. Allow for adequate ventilation during the drying period.

Finish

Not applicable.

Composition

Pigment: Titanium Dioxide, anti-corrosive pigments and extenders Binder: Long Oil Alkyd Solvent: Dearomatised White Spirit

Spreading Rate

Up to10m² per litre on smooth surfaces.

Wet Film Thickness

100 micrometres at 10m² per litre.

Dry Film Thickness

56 micrometres at 10m² per litre.

Volume Solids

56%.

Flash Point

40ºC. (closed cup).

VOC Content

EU limit value for this product (cat.A/d): 450 g/l (2007) / 350 g/l (2010) This product contains max. 349 g/l VOC.

Limitations

Do not apply when air or substrate temperatures are likely to fall below 5ºC or when the relative humidity is above 80% during application or the drying period.

PREPARATION New Surfaces Timber

All Metals Including Galvanised

Additional Surface Preparation All metals Non-ferrous Metals

Lightly abrade to a bright (not polished) surface - excluding galvanised surfaces. Rinse thoroughly with clean water to remove all resides. Allow to dry.

Ferrous Metals

Remove all millscale and rust back to clean metal. Remove all residues. Prime within the working day.

Technical Data Sheet

Previously Decorated Surfaces

Timber

All surfaces must be suitably dry, and free from anything that will interfere with the adhesion of the materials to be applied. Remove all loose, and failing or suspect paint. Remove grey and denatured surfaces by rubbing down with abrasive paper or by mechanical means and round sharp edges 1-3mm. Feather edges of sound paint. Remove all dust. Organic growth must be removed and the areas treated with Albany Fungicidal Wash. Remove any defective putty glazing, clean and prime rebates, replacement putties must be allowed to form a hard skin. Treat knots with two thin coats of fresh knotting. Fill any fixing holes, open joints and shallow surface defects with a suitable proprietary filler or a two pack proprietary wood filler. Rub down witha suitable grade of abrasive paper. Remove all dust. Spot prime bare and filled areas with one coat of Albany Primer.

Metals

Timbers And Metals

Wash remaining sound paint with hot water and liquid detergent solution to remove any contaminants, frequently changing the water. Wet abraded to provide a key. Rinse with clean water to remove all residues. Allow to dry. Bring forward spot primed areas as required with paint system to be used.

Technical Data Sheet

COATING SYSTEM

Apply one coat.

APPLICATION

Stir well before use. Apply by brush or roller. On timber lay off in the direction of the grain. Prior to application, the moisture content of timber substrates should not exceed 18%.

CLEANING

Return surplus material to container. Clean with a proprietary cleaner immediately after use.

MAINTENANCE INFORMATION FOR CDM FILE

HEALTH AND SAFETY

GENERAL INFORMATION

Between maintenance redecoration surfaces may be washed with a warm water and liquid detergent solution to remove surface dirt.

Apply all products in accordance with BS 6150: 2006 Code of practice for painting of buildings and BS 8000: Part 12: 1989 Code of practice for decorative wallcoverings and painting. Under normal and frost free conditions this product will remain usable for up to two years if stored correctly and unopened. Every care is taken to ensure that all information provided on this Technical Data Sheet is accurate. Brewers is unable to guarantee results as it has no control over the conditions under which its products are applied.

Albany House Ashford Road Eastbourne BN21 3TR Tel 01323 411080 Fax 01323 721435 E-mail: enquiries@brewers.co.uk Website: www.brewers.co.uk 17

Technical Data Sheet

ALBANY ALUMINIUM WOOD PRIMER For hardwood and resinous softwood.

AVAILABILITY Colour

Metallic Grey.

Packaging

500ml & 2.5 litres.

PROPERTIES Drying Time

Under normal drying conditions surface dry 4 hours and recoatable after 16 hours. Allow for adequate ventilation during the drying period.

Finish

N/A.

Composition

Pigment: Aluminium paste and extenders Resin: Long Oil Alkyd Solvent: Dearomatised White Spirit

Spreading Rate

Up to 13m² per litre depending on surface texture.

Wet Film Thickness

62 micrometres at 13m² per litre.

Dry Film Thickness

32 micrometres at 13m² per litre.

Volume Solids

52%.

Flash Point

40ºC. (closed cup).

VOC Content

EU limit value for this product (cat.A/g): 450 g/l (2007) / 350 g/l (2010). This product contains max. 349 g/l VOC.

Limitations

Do not apply when air or substrate temperatures are likely to fall below 5ºC or when the relative humidity is above 80% during application or the drying period.

PREPARATION New Surfaces

All surfaces must be suitably dry, and free from anything that will interfere with the adhesion of the materials to be applied. Rub down with a suitable grade of abrasive paper and round sharp edges 1-3mm. Remove all dust. Timber with oils/extractives must be swabbed with clean white spirit, frequently changing the face of the cloths. Treat knots with two thin coats of fresh knotting. Fill any fixing holes, open joints and shallow surface defects with a suitable proprietary filler. Rub down with a suitable grade of abrasive paper. Remove all dust.

Previously Decorated Surfaces

All surfaces must be suitably dry, and free from anything that will interfere with the adhesion of the materials to be applied. Remove all loose, and failing or suspect paint. Remove grey and denatured surfaces by rubbing down with abrasive paper or by mechanical means and round sharp edges 1-3mm. Feather edges of sound paint. Remove all dust. Organic growth must be removed and the areas treated with Albany Fungicidal Wash. Remove any defective putty glazing, clean and prime rebates, replacement putties must be allowed to form a hard skin. Treat knots with two thin coats of fresh knotting. Fill any fixing holes, open joints and shallow surface defects with a suitable proprietary filler. or a two pack proprietary wood filler. Rub down with a suitable grade of abrasive paper. Remove all dust. Wash remaining sound paint with hot water and liquid detergent solution to remove any contaminants, frequently changing the water. Wet abraded to provide a key. Rinse with clean water to remove all residues. Allow to dry. Spot prime bare and filled areas with one coat of Albany Aluminium Wood Primer.

Technical Data Sheet

COATING SYSTEM

Apply one coat.

APPLICATION

Stir well before use. Apply by brush or roller in the direction of the grain. Prior to application, the moisture content of the substrate should not exceed 18%.

CLEANING

Return surplus material to container. Clean with a proprietary cleaner immediately after use.

MAINTENANCE INFORMATION FOR CDM FILE HEALTH AND SAFETY

GENERAL INFORMATION

Albany House Ashford Road Eastbourne BN21 3TR Tel 01323 411080 Fax 01323 721435 E-mail: enquiries@brewers.co.uk Website: www.brewers.co.uk 20

Technical Data Sheet

ALBANY DURABLE MATT EMULSION Albany Durable Matt is formulated for use on new or previously painted interior wall surfaces. 500% stronger than standard vinyl matt, it provides a tough, long lasting matt finish that withstands repetitive cleaning.

AVAILABILITY Colour Range

See Albany Literature.

Packaging

2.5 and 5 litres.

PROPERTIES Drying Time

Under normal drying conditions touch dry in 2 hours, recoatable after 4 hours. Allow for adequate ventilation during the drying period.

Finish

Matt.

Composition

Pigment: Titanium Dioxide, coloured pigments and extenders Binder: Acrylic polymer Solvent: Water

Spreading Rate

14m² per litre on smooth surfaces.

Wet Film Thickness

70 micrometres at 14m² per litre.

Dry Film Thickness

25 micrometres at 14m² per litre.

Volume Solids

34.6% Brilliant White. Other colours will vary.

Flash Point

Not applicable.

VOC Content

EU limit value for this product (cat. A/a): 75g/l (2007) / 30g/l (2010) This product contains max 30 g/l VOC

Limitations

For interior use only. Do not apply when air or substrate temperatures are likely to fall below 8ºC or when the relative humidity is above 80% during application or the drying period.

PREPARATION New Surfaces

Previously Decorated Surfaces

All surfaces must be sound, clean, suitably dry and free from anything that will interfere with the adhesion of the materials to be applied. Powdery surfaces should be primed with Albany Primer Sealer. Porous surfaces should be ‘mist’ coated with Albany Durable Matt Emulsion, thinned with up to 40% clean water. All surfaces must be sound, clean, suitably dry and free from anything that will interfere with the adhesion of the materials to be applied e.g. dirt, grease etc. Remove all loose, failing or suspect paint. Feather edges of sound paint. Remove all dust. Organic growth must be removed and the areas treated with Albany Fungicidal Wash. Fill any fixing holes, cracks and shallow surface defects with an appropriate Filler. Patch prime bare and filled areas of masonry with Albany Primer Sealer. Wash remaining sound paint with hot water and liquid detergent solution to remove any contaminants, frequently changing the water. Any glossy or eggshell surfaces should be wet abraded to provide a key. Rinse with clean water to remove all residues. Allow to dry. Bring forward patch primed areas with one coat of Albany Durable Matt Emulsion.

Technical Data Sheet

COATING SYSTEM

Apply two coats as required.

APPLICATION

Stir well before use. Apply by brush or medium pile roller. For airless spray (dilution may be required). For further information contact Brewers.

CLEANING

Return surplus material to container. Wash with clean water immediately after use.

HEALTH AND SAFETY

GENERAL INFORMATION

Apply all products in accordance with BS 6150: 2006 Code of practice for painting of buildings and BS 8000: Part 12: 1989 Code of practice for decorative wallcoverings and painting. Under normal and frost free conditions this product will remain usable for up to two years if stored correctly and unopened. Every care is taken to ensure that all information provided on this Technical Data Sheet is accurate. Brewers is unable to guarantee results as it has no control over the conditions under which its products are applied.

Albany House Ashford Road Eastbourne BN21 3TR Tel 01323 411080 Fax 01323 721435 E-mail: enquiries@brewers.co.uk Website: www.brewers.co.uk 22

Technical Data Sheet

ALBANY FUNGICIDAL WASH For treating surfaces infected with organic growth contamination.

AVAILABILITY Colour

Colourless.

Packaging

1 and 5 litres.

PROPERTIES Drying Time

Under normal conditions touch dry in 2 hours. Leave for 24 hours then rinse with clean water and allow to dry.

Spreading Rate

Up to 20mÂ˛ per litre when diluted depending on surface suction. On textured surfaces the spreading rate will be reduced.

Wet Film Thickness

Not applicable. Ensure that affected areas are well saturated during application.

Dry Film Thickness

Not applicable.

Volume Solids

Not applicable.

Flash Point

Not applicable.

VOC Content

Not applicable.

Limitations

Do not apply if there is a risk of rain or frost, use as a paint additive, mix with other chemicals, or apply by power spray machines. Albany Fungicidal Wash is a surface treatment and does not provide preservation properties to any substrate.

PREPARATION Undecorated Surfaces

All surfaces must be sound, suitably dry and free from anything that will interfere with the adhesion of the materials to be applied. Remove all organic growth by scraping or brushing with a stiff bristle brush (not wire). Heavy long established growth is best removed by pressure washing between 1500-2000 psi (102-136 bar), wet or dry grit blasting. Care must be taken not to damage the underlying surface. The spores must then be killed with an application of Albany Fungicidal Wash diluted one volume of Fungicidal Wash with up to four volumes clean water. Leave for 24 hours and rinse with clean water. Allow to dry.

Previously Decorated Surfaces

All surfaces must be sound, suitably dry and free from anything that will interfere with the adhesion of the material to be applied. Remove all loose, and failing or suspect material by scraping or brushing with a stiff bristle brush (not wire) to a sound edge. Remove all organic growth by scraping or brushing with a stiff bristle brush (not wire). Heavy long established growth is best removed by pressure washing between 1500-2000 psi (102-136 bar), wet or dry grit blasting. Care must be taken not to damage the underlying surface. The spores must the be killed with a application of Albany Fungicidal Wash diluted one volume of Fungicidal Wash with up to four volumes clean water. Leave for 24 hours and rinse with clean water. Allow to dry.

Technical Data Sheet

COATING SYSTEM

One application. When growth has been severe a second application may be necessary.

APPLICATION

Apply liberally using a synthetic bristle brush and scrub well into the surface.

CLEANING

Wash with clean water immediately after use.

MAINTENANCE INFORMATION FOR CDM FILE HEALTH AND SAFETY

GENERAL INFORMATION

Albany House Ashford Road Eastbourne BN21 3TR Tel 01323 411080 Fax 01323 721435 E-mail: enquiries@brewers.co.uk Website: www.brewers.co.uk 24

Technical Data Sheet

ALBANY GLOSS A tough durable high gloss finish for interior and exterior use.

AVAILABILITY Colour

Refer to current Albany Literature.

Packaging

1, 2.5 and 5 litres.

PROPERTIES Drying Time

Under normal drying conditions touch dry in 4 hours, recoatable after 16 hours. Allow for adequate ventilation during the drying period.

Finish

Gloss.

Composition

Pigment: Titanium Dioxide and coloured pigments Resin: Alkyd Solvent: Dearomatised White Spirit

Spreading Rate

Up to16m² per litre depending on surface texture.

Wet Film Thickness

67 micrometres at 16m² per litre.

Dry Film Thickness

31 micrometres at 16m² per litre.

Volume Solids

46% Brilliant White. Other colours will vary.

Flash Point

40ºC. (closed cup).

VOC Content

EU limit value for this product (cat.A/d): 400 g/l (2007) / 300 g/l (2010) This product contains max. 299 g/l VOC.

Limitations

Do not apply when air or substrate temperatures are likely to fall below 5ºC or when the relative humidity is above 80% during application or the drying period.

PREPARATION New Surfaces Timber

All metals including galvanised

Technical Data Sheet

Additional surface preparation all metals Non-ferrous metals

Ferrous metals

Remove all millscale and rust back to clean metal. Remove all residues. Prime within the working day with one coat of Albany Metal Primer.

Previously decorated surfaces

Timber

All surfaces must be suitably dry, and free from anything that will interfere with the adhesion of the materials to be applied. Remove all loose, and failing or suspect paint. Prior to painting the moisture should not exceed 18%. Remove grey and denatured surfaces by rubbing down with abrasive paper or by mechanical means and round sharp edges 1-3mm. Feather edges of sound paint. Remove all dust. Organic growth must be removed and the areas treated with Albany Fungicidal Wash. Remove any defective putty glazing, clean and prime rebates, replacement putties must be allowed to form a hard skin. Treat knots with two thin coats of fresh knotting. Fill any fixing holes, open joints and shallow surface defects with a suitable proprietary wood filler. Rub down with a suitable grade of abrasive paper. Remove all dust.

Metals

Timber and metals

Technical Data Sheet

COATING SYSTEM

Apply one or two coats as required. Maintain a wet edge.

APPLICATION

Stir well before use. Apply by brush to an even thickness (a fine, soft long filament bristle brush gives best results). Maintain a wet edge. On timber lay off in the direction of the grain.

CLEANING

Return surplus material to container. Clean with a proprietary cleaner immediately after use.

MAINTENANCE INFORMATION FOR CDM FILE HEALTH AND SAFETY

GENERAL INFORMATION

Albany House Ashford Road Eastbourne BN21 3TR Tel 01323 411080 Fax 01323 721435 E-mail: enquiries@brewers.co.uk Website: www.brewers.co.uk 27

Technical Data Sheet

ALBANY HIGH OPACITY SUPERCOVER A high opacity matt finish suitable for new plaster.

AVAILABILITY Colour Range

Refer to current Albany Literature.

Packaging

5 litres, (10 litres White & Magnolia).

PROPERTIES Drying Time

Under normal drying conditions touch dry 2 hours, recoatable after 4 hours. Allow for adequate ventilation during the drying period.

Finish

Matt.

Composition

Pigment: Titanium Dioxide, coloured pigments and extenders Binder: Vinyl acetate copolymer Solvent: Water

Spreading Rate

Up to 16m² per litre on smooth surfaces.

Wet Film Thickness

62 micrometres at 16m² per litre.

Dry Film Thickness

16 micrometres at 16m² per litre.

Volume Solids

25% White other colours will vary.

Flash Point

Not applicable.

VOC Content

EU limit value for this product (cat.A/a): 75 g/l (2007) / 30 g/l (2010) This product contains max. 19 g/l VOC.

Limitations

For interior use only. Do not apply when air or substrate temperatures are likely to fall below 8ºC or when the relative humidity is above 80% during application or the drying period.

PREPARATION New Surfaces

Previously Decorated Surfaces

All surfaces must be sound, clean, suitably dry and free from anything that will interfere with the adhesion of the materials to be applied. Powdery, polished plaster or dense surfaces should be primed with Albany Primer Sealer. Porous surfaces should be ‘mist’ coated with Albany High Opacity Supercover thinned with up to 10% clean water.

All surfaces must be sound, clean, suitably dry and free from anything that will interfere with the adhesion of the materials to be applied e.g. dirt, grease etc. Remove all loose, failing or suspect paint. Feather edges of sound paint. Remove all dust. Organic growth must be removed and the areas treated with Albany Fungicidal Wash. Fill any fixing holes, cracks and shallow surface defects with a suitable proprietary filler. Patch prime bare and filled areas with Albany Primer Sealer. Wash remaining sound paint with hot water and liquid detergent solution to remove any contaminants, frequently changing the water. Any glossy or eggshell surfaces should be wet abraded to provide a key. Rinse with clean water to remove all residues. Allow to dry. If after cleaning any areas still contaminated with substances likely to cause staining and/or bleeding, patch prime with one coat of Albany Prime Sealer. Bring forward patch primed areas with one coat of Albany High Opacity Supercover.

Technical Data Sheet

COATING SYSTEM

Apply two coats as required.

APPLICATION

Stir well before use. Apply by brush, roller or spray. For spray application dilution may be required.

CLEANING

Return surplus material to container. Wash with clean water immediately after use.

MAINTENANCE INFORMATION FOR CDM FILE HEALTH AND SAFETY

GENERAL INFORMATION

Albany House Ashford Road Eastbourne BN21 3TR Tel 01323 411080 Fax 01323 721435 E-mail: enquiries@brewers.co.uk Website: www.brewers.co.uk 30

Technical Data Sheet

ALBANY METAL PRIMER A high performance metal primer: anti corrosive and rust inhibiting.

AVAILABILITY Colour

Green.

Packaging

2.5 litres.

PROPERTIES Drying Time

Under normal drying conditions surface dry 6 hours and recoatable after 16 hours. Allow for adequate ventilation during the drying period.

Finish

Matt.

Composition

Pigment: Titainium dioxide Zinc phosphate, Zinc Oxide and extenders Resin: Long Oil Alkyd Solvent: Dearomatised White Spirit

Spreading Rate

Up to 13m² per litre on smooth surfaces.

Wet Film Thickness

77 micrometres at 13m² per litre.

Dry Film Thickness

33 micrometres at 13m² per litre.

Volume Solids

43%.

Flash Point

40ºC (closed cup).

VOC Content

EU limit value for this product (cat.A/i): 600 g/l (2007) / 500 g/l (2010) This product contains max. 445 g/l VOC.

Limitations

Do not apply when air or substrate temperatures are likely to fall below 5ºC or when the relative humidity is above 80% during application or the drying period.

PREPARATION New Surfaces

Previously Decorated Surfaces

Surfaces must be clean and free from anything that will interfere with the materials to be applied. Wash with hot water and liquid detergent solution to remove oil, grease or any other contaminants, frequently changing the water. Rinse thoroughly with clean water. Allow to dry. Remove all millscale and rust back to clean metal. Remove all residues. All surfaces must be suitably dry, and free from anything that will interfere with the adhesion of the materials to be applied. Remove all loose, and failing or suspect paint. Feather edges of sound paint. Remove all dust. Remove all rust. Spot prime bare areas with one coat of Albany Metal Primer. Wash remaining sound paint with hot water and liquid detergent solution to remove any contaminants, frequently changing the water. Wet abraded to provide a key. Rinse with clean water to remove all residues. Allow to dry. Bring forward spot primed areas as required by paint system to be used.

Technical Data Sheet

COATING SYSTEM

Apply one coat.

APPLICATION

Stir well before use. Apply by brush or roller.

CLEANING

Return surplus material to container. Clean with a proprietary cleaner immediately after use.

MAINTENANCE INFORMATION FOR CDM FILE HEALTH AND SAFETY

GENERAL INFORMATION

Between maintenance redecoration surfaces may be washed with a warm water and liquid detergent solution to remove surface dirt. Please refer to the Safety, Health and Environmental Information on the container. Take special precautions during the surface preparation of pre 1960â&#x20AC;&#x2122;s painted surfaces as they may contain harmful lead. For further information contact Brewer. When preparing all surfaces avoid the inhalation of dust and/or metal particles. Wear a suitable facemask. Material Safety Data Sheets for this and all other Albany products are freely available from the place of purchase or the address below. Store in secure dry conditions inaccessible to children or animals. Containers should be kept closed during storage. Do not empty into drains, watercourses or access routes to septic tanks. Apply all products in accordance with BS 6150: 2006 Code of practice for painting of buildings and BS 8000: Part 12: 1989 Code of practice for decorative wallcoverings and painting. Under normal and frost free conditions this product will remain usable for up to two years if stored correctly and unopened. Every care is taken to ensure that all information provided on this Technical Data Sheet is accurate. Brewers are unable to guarantee results as it has no control over the conditions under which its products are applied.

Albany House Ashford Road Eastbourne BN21 3TR Tel 01323 411080 Fax 01323 721435 E-mail: enquiries@brewers.co.uk Website: www.brewers.co.uk 32

Technical Data Sheet

ALBANY NON DRIP GLOSS High gloss for wood or metal.

AVAILABILITY Colour Range

Refer to current Albany literature.

Packaging

750ml & 2.5 litre.

PROPERTIES Drying Time

Under normal drying conditions surface dry 3 hours and recoatable after 16 hours. Allow for adequate ventilation during the drying period.

Finish

Gloss.

Composition

Pigment: Titanium Dioxide and coloured pigments. Resin: Thixotropic Alkyd Solvent: Dearomatised White Spirit.

Spreading Rate

Up to 12m² per litre depending on surface texture.

Wet Film Thickness

83 micrometres at 12m² per litre.

Dry Film Thickness

45 micrometres at 12m² per litre.

Volume Solids

54% Brilliant White other colours will vary.

Flash Point

40ºC (closed cup).

VOC Content

EU limit value for this product (cat.A/d): 400 g/l (2007) / 300 g/l (2010) This product contains max. 289 g/l VOC.

Limitations

Do not apply when air or substrate temperatures are likely to fall below 5ºC or when the relative humidity is above 80% during application or the drying period.

PREPARATION New Surfaces Timber

All Metals including Galvanised

Additional Surface Preparation - All Metals Non-Ferrous Metals

Ferrous Metals

All surfaces must be suitably dry, and free from anything that will interfere with the adhesion of the materials to be applied. Rub down with a suitable grade of abrasive paper and round sharp edges 1-3mm. Remove all dust. Treat knots with two thin coats of fresh knotting. Fill any fixing holes, open joints and shallow surface defects with a suitable proprietary filler. Rub down with a suitable grade of abrasive paper. Remove all dust. Prior to priming the moisture content of the substrate should not exceed 18%. Prime with one coat of Albany Wood Primer. Surfaces must be clean and free from anything that will interfere with the materials to be applied. Wash with hot water and liquid detergent solution to remove oil, grease or any other contaminants, frequently changing the water. Rinse thoroughly with clean water. Allow to dry. galvanised surfaces should be pre-treated with a suitable mordant solution. Overall blackening of the surface will confirm satisfactory surface preparation.

Lightly abrade to a bright (not polished) surface-excluding galvanised surfaces. Rinse thoroughly with clean water to remove all resides. Allow to dry. Prime, including galvanised surfaces, with one coat of Albany All Purpose Primer. Remove all millscale and rust back to clean metal. Remove all residues. Prime within the working day with one coat of Albany Metal Primer.

Technical Data Sheet

Previously Decorated Surfaces - Timber

Metals

Timber and Metals

Wash remaining sound paint with hot water and liquid detergent solution to remove any contaminants, frequently changing the water. Wet abraded to provide a key. Rinse with clean water to remove all residues. Allow to dry. Bring forward all spot primed areas with an additional coat of primer and allow to dry.

COATING SYSTEM

Apply one or two coats as required. Maintain a wet edge.

APPLICATION

Apply by brush to an even thickness (a fine, soft long filament bristle brush gives best results). Maintain a wet edge. On timber lay off in the direction of the grain.

CLEANING

Return surplus material to container. Clean with a proprietary cleaner immediately after use.

MAINTENANCE INFORMATION FOR CDM FILE HEALTH AND SAFETY

All surfaces must be suitably dry, and free from anything that will interfere with the adhesion of the materials to be applied. Remove all loose, and failing or suspect paint. Prior to painting the moisture should not exceed 18%. Remove grey and denatured surfaces by rubbing down with abrasive paper or by mechanical means and round sharp edges 1-3mm. Feather edges of sound paint. Remove all dust. Organic growth must be removed and the areas treated with Albany Fungicidal Wash. Remove any defective putty glazing, clean and prime rebates, replacement putties must be allowed to form a hard skin. Treat knots with two thin coats of fresh knotting. Fill any fixing holes, open joints and shallow surface defects with a suitable proprietary filler or a two pack proprietary wood filler. Rub down with a suitable grade of abrasive paper. Remove all dust.

Technical Data Sheet

GENERAL INFORMATION

Albany House Ashford Road Eastbourne BN21 3TR Tel 01323 411080 Fax 01323 721435 E-mail: enquiries@brewers.co.uk Website: www.brewers.co.uk 35

Technical Data Sheet

ALBANY POLYURETHANE EGGSHELL VARNISH Albany Polyurethane Varnish produces a clear, highly durable finish on interior woodwork. It is easy to apply, washable and resists knocks, scratches and hot drinks.

AVAILABILITY Colour

Clear.

Packaging

1 and 2.5 litres.

PROPERTIES Drying Time

Under normal drying conditions touch dry in 4-6 hours, recoatable after 16-24 hours. Allow for adequate ventilation during the drying period.

Finish

Eggshell.

Composition

Resin: Urethane and Alkyd Resins Solvent: Dearomatised White Spirit

Spreading Rate

Up to13m² per litre depending on surface texture.

Wet Film Thickness

76 micrometres at 13m² per litre.

Dry Film Thickness

38 micrometres at 13m² per litre.

Volume Solids

50% Brilliant White. Other colours will vary.

Flash Point

60ºC. (closed cup).

VOC Content

EU limit value for this product (cat.A/e): 500 g/l (2007) / 400 g/l (2010) This product contains max. 399 g/l VOC.

Limitations

Do not apply when air or substrate temperatures are likely to fall below 5ºC or when the relative humidity is above 80% during application or the drying period.

PREPARATION New Surfaces Timber

All surfaces must be suitably dry, and free from anything that will interfere with the adhesion of the materials to be applied. Rub down with a suitable grade of abrasive paper and round sharp edges 1-3mm. Remove all dust. Timber with oils/extractives must be swabbed with clean methylated spirits, frequently changing the face of the cloths. Fill any fixing holes, open joints and shallow surface defects with a suitable proprietary wood filler to match the colour of the bare timber. Rub down with a suitable grade of abrasive paper. Remove all dust.

Previously vanished surfaces

All surfaces must be suitably dry, and free from anything that will interfere with the adhesion of the materials to be applied. Remove all loose, and failing or suspect varnish and any grey denatured timber. Prior to coating, the moisture should not exceed 18%. Feather edges of sound varnish. Remove all dust. Organic growth must be removed and the areas treated with Albany Fungicidal Wash. Fill any fixing holes, open joints and shallow surface defects with a suitable proprietary wood filler to match the colour of the bare timber. Rub down with a suitable grade of abrasive paper. Remove all dust. Spot varnish bare and filled areas with Albany Eggshell Varnish. Wash remaining sound varnish with hot water and liquid detergent solution to remove any contaminants, frequently changing the water. Wet abraded to provide a key. Rinse with clean water to remove all residues. Allow to dry. Bring forward spot primed areas with one coat of the Albany Eggshell Varnish.

Technical Data Sheet

COATING SYSTEM

Apply two or three full coats as required. Maintain a wet edge.

APPLICATION

Stir well before use. Apply by brush to an even thickness (a fine, soft long filament bristle brush gives best results). Maintain a wet edge. On timber lay off in the direction of the grain.

CLEANING

Return surplus material to container. Clean with a proprietary cleaner immediately after use.

MAINTENANCE INFORMATION FOR CDM FILE HEALTH AND SAFETY

GENERAL INFORMATION

Albany House Ashford Road Eastbourne BN21 3TR Tel 01323 411080 Fax 01323 721435 E-mail: enquiries@brewers.co.uk Website: www.brewers.co.uk 38

Technical Data Sheet

ALBANY POLYURETHANE GLOSS VARNISH Albany Polyurethane Varnish produces a clear, highly durable finish on interior woodwork. It easy to apply, washable and resists knocks, scratches and hot drinks.

AVAILABILITY Colour

Clear.

Packaging

1 and 2.5 litres.

PROPERTIES Drying Time

Under normal drying conditions touch dry in 4-6 hours, recoatable after 16-24 hours. Allow for adequate ventilation during the drying period.

Finish

Gloss.

Composition

Resin: Urethane and Alkyd Resins Solvent: Dearomatised White Spirit

Spreading Rate

Up to13m² per litre depending on surface texture.

Wet Film Thickness

76 micrometres at 13m² per litre.

Dry Film Thickness

38 micrometres at 13m² per litre.

Volume Solids

50% Brilliant White. Other colours will vary.

Flash Point

60ºC. (closed cup).

VOC Content

EU limit value for this product (cat.A/e): 500 g/l (2007) / 400 g/l (2010) This product contains max. 399 g/l VOC.

Limitations

Do not apply when air or substrate temperatures are likely to fall below 5ºC or when the relative humidity is above 80% during application or the drying period.

PREPARATION New Surfaces Timber

All surfaces must be suitably dry, and free from anything that will interfere with the adhesion of the materials to be applied. Rub down with a suitable grade of abrasive paper and round sharp edges 1-3mm. Remove all dust. Timber with oils/extractives must be swabbed with clean methylated spirits, frequently changing the face of the cloths. Fill any fixing holes, open joints and shallow surface defects with a suitable proprietary wood filler to match the colour of the bare timber. Rub down with a suitable grade of abrasive paper. Remove all dust.

Previously varnished surfaces

All surfaces must be suitably dry, and free from anything that will interfere with the adhesion of the materials to be applied. Remove all loose, and failing or suspect vanish and any grey denatured timber. Prior to coating, the moisture should not exceed 18%. Feather edges of sound varnish. Remove all dust. Organic growth must be removed and the areas treated with Albany Fungicidal Wash. Fill any fixing holes, open joints and shallow surface defects with a suitable proprietary wood filler to match the colour of the bare timber. Rub down with a suitable grade of abrasive paper. Remove all dust. Spot varnish bare and filled areas with Albany Gloss Varnish. Wash remaining sound varnish with hot water and liquid detergent solution to remove any contaminants, frequently changing the water. Wet abraded to provide a key. Rinse with clean water to remove all residues. Allow to dry. Bring forward spot primed areas with one coat of the Albany Gloss Varnish.

Technical Data Sheet

COATING SYSTEM

Apply two or three coats as required. Maintain a wet edge.

APPLICATION

Stir well before use. Apply by brush to an even thickness (a fine, soft long filament bristle brush gives best results). Maintain a wet edge. On timber lay off in the direction of the grain.

CLEANING

Return surplus material to container. Clean with a proprietary cleaner immediately after use.

MAINTENANCE INFORMATION FOR CDM FILE HEALTH AND SAFETY

GENERAL INFORMATION

Albany House Ashford Road Eastbourne BN21 3TR Tel 01323 411080 Fax 01323 721435 E-mail: enquiries@brewers.co.uk Website: www.brewers.co.uk 40

Technical Data Sheet

ALBANY POLYURETHANE MATT VARNISH Albany Polyurethane Varnish produces a clear, highly durable finish on interior woodwork. It easy to apply, washable and resists knocks, scratches and hot drinks.

AVAILABILITY Colour

Clear.

Packaging

1 and 2.5 litres.

PROPERTIES Drying Time

Under normal drying conditions touch dry in 4-6 hours, recoatable after 16-24 hours. Allow for adequate ventilation during the drying period.

Finish

Matt.

Composition

Resin: Urethane and Alkyd Resins Solvent: Dearomatised White Spirit

Spreading Rate

Up to13m² per litre depending on surface texture.

Wet Film Thickness

76 micrometres at 13m² per litre.

Dry Film Thickness

38 micrometres at 13m² per litre.

Volume Solids

50% Brilliant White. Other colours will vary.

Flash Point

60ºC. (closed cup).

VOC Content

EU limit value for this product (cat.A/e): 500 g/l (2007) / 400 g/l (2010) This product contains max. 399 g/l VOC.

Limitations

Do not apply when air or substrate temperatures are likely to fall below 5ºC or when the relative humidity is above 80% during application or the drying period.

PREPARATION New Surfaces Timber

All surfaces must be suitably dry, and free from anything that will interfere with the adhesion of the materials to be applied. Rub down with a suitable grade of abrasive paper and round sharp edges 1-3mm. Remove all dust. Timber with oils/extractives must be swabbed with clean methylated spirits, frequently changing the face of the cloths. Fill any fixing holes, open joints and shallow surface defects with a suitable proprietary wood filler to match the colour of the bare timber. Rub down with a suitable grade of abrasive paper. Remove all dust.

Previously varnished surfaces

All surfaces must be suitably dry, and free from anything that will interfere with the adhesion of the materials to be applied. Remove all loose, and failing or suspect varnish and any grey denatured timber. Prior to coating, the moisture should not exceed 18%. Feather edges of sound varnish. Remove all dust. Organic growth must be removed and the areas treated with Albany Fungicidal Wash. Fill any fixing holes, open joints and shallow surface defects with a suitable proprietary wood filler to match the colour of the bare timber. Rub down with a suitable grade of abrasive paper. Remove all dust. Spot varnish bare and filled areas with Albany Matt Varnish. Wash remaining sound varnish with hot water and liquid detergent solution to remove any contaminants, frequently changing the water. Wet abraded to provide a key. Rinse with clean water to remove all residues. Allow to dry. Bring forward spot primed areas with one coat of the Albany Matt Varnish.

Technical Data Sheet

COATING SYSTEM

Apply two or three full coats as required. Maintain a wet edge.

APPLICATION

Stir well before use. Apply by brush to an even thickness (a fine, soft long filament bristle brush gives best results). Maintain a wet edge. On timber lay off in the direction of the grain.

CLEANING

Return surplus material to container. Clean with a proprietary cleaner immediately after use.

MAINTENANCE INFORMATION FOR CDM FILE HEALTH AND SAFETY

GENERAL INFORMATION

Albany House Ashford Road Eastbourne BN21 3TR Tel 01323 411080 Fax 01323 721435 E-mail: enquiries@brewers.co.uk Website: www.brewers.co.uk 42

Technical Data Sheet

ALBANY PRIMER SEALER A dual purpose, alkali resisting primer, ideal for dry, aged plaster.

AVAILABILITY Colour Range

Pale Cream.

Packaging

1, 2.5 & 5 litres.

PROPERTIES Drying Time

Under normal drying conditions surface dry 4 hours recoatable after 16 hours. Allow for adequate ventilation during the drying period.

Finish

Pale Cream.

Composition

Pigment: Titanium Dioxide and extenders Resin: Epoxy ester Solvent: Dearomatised White Spirit

Spreading Rate

Up to 15m² per litre smooth surfaces.

Wet Film Thickness

66 micrometres at 15m² per litre.

Dry Film Thickness

25 micrometres at 15m² per litre.

Volume Solids

38%.

Flash Point

40ºC (closed cup).

VOC Content

EU limit value for this product (cat.A/g): 750 g/l (2007) / 750 g/l (2010) This product contains max. 499 g/l VOC.

Limitations

Do not apply when air or substrate temperatures are likely to fall below 5ºC or when the relative humidity is above 80% during application or the drying period.

PREPARATION New Surfaces

Previously Decorated Surfaces

All surfaces must be sound, clean, suitably dry and free from anything that will interfere with the adhesion of the materials to be applied. Prime surfaces as required including powdery, polished plaster or dense surfaces with Albany Primer Sealer.

Technical Data Sheet

COATING SYSTEM

Apply one coat.

APPLICATION

Stir well before use. Apply by brush or roller.

MAINTENANCE INFORMATION FOR CDM FILE HEALTH AND SAFETY

GENERAL INFORMATION

Albany House Ashford Road Eastbourne BN21 3TR Tel 01323 411080 Fax 01323 721435 E-mail: enquiries@brewers.co.uk Website: www.brewers.co.uk 44

Technical Data Sheet

ALBANY RED OXIDE PRIMER Provides initial protection for iron and steel surfaces.

AVAILABILITY Colour Range

Red Oxide.

Packaging

2.5 & 5 litres.

PROPERTIES Drying Time

Under normal drying conditions surface dry 4 hours and recoatable after 16 hours. Allow for adequate ventilation during the drying period.

Finish

Not applicable.

Composition

Pigment: Iron oxide and extenders Resin: Long Oil Alkyd Solvent: Dearomatised White Spirit

Spreading Rate

15m² per litre on smooth surfaces.

Wet Film Thickness

66 micrometres at 15m² per litre.

Dry Film Thickness

33 micrometres at 15m² per litre.

Volume Solids

50%.

Flash Point

40ºC.

VOC Content

EU limit value for this product (cat.A/i): 600 g/l (2007) / 500 g/l (2010) This product contains max. 499 g/l VOC.

Limitations

Do not apply when air or substrate temperatures are likely to fall below 5ºC or when the relative humidity is above 80% during application or the drying period.

PREPARATION New Surfaces

Previously Decorated Surfaces

All surfaces must be suitably dry, and free from anything that will interfere with the adhesion of the materials to be applied. Remove all loose, and failing or suspect paint. Feather edges of sound paint. Remove all dust. Remove all rust. Spot prime bare areas with one coat of Albany Red Oxide Primer. Wash remaining sound paint with hot water and liquid detergent solution to remove any contaminants, frequently changing the water. Wet abraded to provide a key. Rinse with clean water to remove all residues. Allow to dry. Bring forward spot primed areas with one coat of Albany Red Oxide Primer.

Technical Data Sheet

COATING SYSTEM

Apply one or two coats as required.

APPLICATION

Stir well before use. Apply by brush or roller.

MAINTENANCE INFORMATION FOR CDM FILE HEALTH AND SAFETY

GENERAL INFORMATION

Albany House Ashford Road Eastbourne BN21 3TR Tel 01323 411080 Fax 01323 721435 E-mail: enquiries@brewers.co.uk Website: www.brewers.co.uk 46

Technical Data Sheet

ALBANY SMOOTH DURABLE EGGSHELL A durable sheen finish with a smooth even film.

AVAILABILITY Colour

Refer to current Albany Literature.

Packaging

1, 2.5 and 5 litres.

PROPERTIES Drying Time

Under normal drying conditions touch dry in 4 hours, recoatable after 16 hours. Allow for adequate ventilation during the drying period.

Finish

Eggshell.

Composition

Pigment: Titanium Dioxide, coloured pigments and extenders Resin: Long Oil Alkyd Solvent: Dearomatised White Spirit

Spreading Rate

Up to 18m² per litre depending on surface texture.

Wet Film Thickness

56 micrometres at 17m² per litre.

Dry Film Thickness

25 micrometres at 17m² per litre.

Volume Solids

44% Brilliant White. Other colours will vary.

Flash Point

40ºC. (closed cup).

VOC Content

EU limit value for this product (cat.A/d): 400 g/l (2007) / 300 g/l (2010). This product contains max. 299 g/l VOC.

Limitations

For interior use only. Do not apply when air or substrate temperatures are likely to fall below 5ºC or when the relative humidity is above 80% during application or the drying period.

PREPARATION New Surfaces

All surfaces must be sound, clean, suitably dry and free from anything that will interfere with the adhesion of the materials to be applied. Prime all surfaces including powdery, polished plaster or dense surfaces with Albany Primer Sealer.

Previously Decorated Surfaces

All surfaces must be sound, clean, suitably dry and free from anything that will interfere with the adhesion of the materials to be applied e.g. dirt, grease etc. Remove all loose, failing or suspect paint. Feather edges of sound paint. Remove all dust. Organic growth must be removed and the areas treated with Albany Fungicidal Wash. Fill any fixing holes, cracks and shallow surface defects with a suitable proprietary filler. Patch prime bare and filled areas with Albany Primer Sealer. Wash remaining sound paint with hot water and liquid detergent solution to remove any contaminants, frequently changing the water. Any glossy or eggshell surfaces should be wet abraded to provide a key. Rinse with clean water to remove all residues. Allow to dry. If after cleaning any areas still contaminated with substances likely to cause staining and/or bleeding, patch prime with one coat of Albany Primer Sealer. Bring forward patch primed areas with one coat of Albany Smooth Durable Eggshell.

Technical Data Sheet

COATING SYSTEM

Apply two coats as required.

APPLICATION

Stir well before use. Apply by brush or roller.

CLEANING

Return surplus material to container. Clean with a proprietary cleaner immediately after use.

MAINTENANCE INFORMATION FOR CDM FILE HEALTH AND SAFETY

GENERAL INFORMATION

Albany House Ashford Road Eastbourne BN21 3TR Tel 01323 411080 Fax 01323 721435 E-mail: enquiries@brewers.co.uk Website: www.brewers.co.uk 48

Technical Data Sheet

ALBANY SMOOTH MASONRY PAINT A durable, flexible smooth matt finish for exterior masonry.

AVAILABILITY Colour Range

Refer to current Albany literature.

Packaging

2.5, 5 & 10 litres.

PROPERTIES Drying Time

Under normal drying conditions touch dry 2 hours, recoatable after 6 hours.

Finish

Matt.

Composition

Pigment: Titanium Dioxide, light fast coloured pigments and extenders Binder: Vinyl acetate copolymer Solvent: Water

Spreading Rate

Up to 10m² per litre. On textured / porous surface the spreading rate will be reduced.

Wet Film Thickness

100 micrometres at 10m² per litre.

Dry Film Thickness

32.6 micrometres at 13m² per litre.

Volume Solids

32.6% Brilliant White. Other colours will vary.

Flash Point

Not applicable.

VOC Content

EU limit value for this product (cat.A/c): 75 g/l (2007) / 40 g/l (2010) This product contains max. 1g/l VOC.

Limitations

Do not apply when there is a risk of rain, air or substrate temperatures are likely to fall below 8ºC or when the relative humidity is above 80% during application or the drying period. Do not use on bitumen coatings. The decoration of Fletton brickwork either facings or commons is not recommended.

PREPARATION New Surfaces

All surfaces must be sound, suitably dry and free from anything that will interfere with the adhesion of the materials to be applied. Surfaces with suction (porous surfaces) should be treated with an application of Albany Stabilising Solution.

Previously Decorated Surfaces

All surfaces must be sound, suitably dry and free from anything that will interfere with the adhesion of the material to be applied. Remove all loose, and failing or suspect material by scraping or brushing with a stiff bristle brush (not wire) to a sound edge. Organic growth must be removed and the areas treated with Albany Fungicidal Wash. For surfaces in poor condition mechanical means may be necessary e.g. pressure washing between 1500-2000 psi (102-136 bar), proprietary paint removal system, wet or dry grit blasting. Care must be taken not to damage the underlying surface. Fill cracks and small defects in masonry surfaces with a suitable proprietary filler and finish to match existing. Stabilise all bare, filled and previously decorated chalking areas with an application of Albany Stabilising Solution. Wash any soundly adhering gloss painted surfaces with hot water and liquid detergent solution to remove any contaminants frequently changing the water. Wet abrade to provide a key. Rinse thoroughly with clean water to remove all residues.

Technical Data Sheet

COATING SYSTEM

Apply two coats as required.

APPLICATION

Stir well before use. Apply by brush, medium or long pile roller depending on surface texture, or by airless spray. For airless spray use a minimum fluid pressure of 2000psi (136 bar) and a minimum tip size of 0.018 thou. Mask as necessary with a wet strength grade masking paper.

CLEANING

Return surplus material to container. Wash with clean water immediately after use.

MAINTENANCE INFORMATION FOR CDM FILE HEALTH AND SAFETY

GENERAL INFORMATION

Albany House Ashford Road Eastbourne BN21 3TR Tel 01323 411080 Fax 01323 721435 E-mail: enquiries@brewers.co.uk Website: www.brewers.co.uk 50

Technical Data Sheet

ALBANY SOFT SHEEN EMULSION A subtle soft sheen for interior walls and ceilings.

AVAILABILITY Colour Range

Refer to current Albany Literature.

Packaging

2.5 & 5 litres.

PROPERTIES Drying Time

Under normal drying conditions touch dry 2 hours, recoatable after 4 hours. Allow for adequate ventilation during the drying period.

Finish

Mid Sheen.

Composition

Pigment: Titanium Dioxide, coloured pigments and extenders Binder: Vinyl acetate copolymer Solvent: Water

Spreading Rate

Up to 14m² per litre on smooth surfaces.

Wet Film Thickness

71 micrometres at 14m² per litre.

Dry Film Thickness

24 micrometres at 14m² per litre.

Volume Solids

33.6% Brilliant White other colours will vary.

Flash Point

Not applicable.

VOC Content

EU limit value for this product (cat.A/a): 75 g/l (2007) / 30 g/l (2010) This product contains max. 1g/l VOC.

Limitations

For interior use only. Do not apply when air or substrate temperatures are likely to fall below 8ºC or when the relative humidity is above 80% during application or the drying period.

PREPARATION New Surfaces

Previously Decorated Surfaces

All surfaces must be sound, clean, suitably dry and free from anything that will interfere with the adhesion of the materials to be applied. Powdery, polished plaster or dense surfaces should be primed with Albany Primer Sealer. Porous surfaces should be ‘mist’ coated with Albany Soft Sheen Emulsion thinned with up to 10% clean water.

All surfaces must be sound, clean, suitably dry and free from anything that will interfere with the adhesion of the materials to be applied e.g. dirt, grease etc. Remove all loose, failing or suspect paint. Feather edges of sound paint. Remove all dust. Organic growth must be removed and the areas treated with Albany Fungicidal Wash. Fill any fixing holes, cracks and shallow surface defects with a suitable proprietary filler. Patch prime bare and filled areas with Albany Primer Sealer. Wash remaining sound paint with hot water and liquid detergent solution to remove any contaminants, frequently changing the water. Any glossy or eggshell surfaces should be wet abraded to provide a key. Rinse with clean water to remove all residues. Allow to dry. If after cleaning any areas still contaminated with substances likely to cause staining and/or bleeding, patch prime with one coat of Albany Primer Sealer. Bring forward patch primed areas with one coat of Albany Soft Sheen Emulsion.

Technical Data Sheet

COATING SYSTEM

Apply two coats as required.

APPLICATION

Stir well before use. Apply by brush, roller or spray. For spray application dilution may be required.

CLEANING

Return surplus material to container. Wash with clean water immediately after use.

MAINTENANCE INFORMATION FOR CDM FILE HEALTH AND SAFETY

GENERAL INFORMATION

Albany House Ashford Road Eastbourne BN21 3TR Tel 01323 411080 Fax 01323 721435 E-mail: enquiries@brewers.co.uk Website: www.brewers.co.uk 52

Technical Data Sheet

ALBANY STABILISING SOLUTION A penetrating sealer for masonry surfaces.

AVAILABILITY Colour

Clear.

Packaging

2.5 & 5 litres.

PROPERTIES Drying Time

Under normal drying conditions touch dry after 2 hours, recoatable after 16 hours.

Finish

Not applicable.

Composition

Resin: Epoxy Ester Solvent: Dearomatised White Spirit

Spreading Rate

Up to 6m² per litre. On textured and surfaces with suction the spreading rate will be reduced.

Wet Film Thickness

166 micrometres at 6m² per litre.

Dry Film Thickness

41 micrometres at 6m² per litre.

Volume Solids

24%.

Flash Point

40ºC (closed cup).

VOC Content

EU limit value for this product (cat.A/h): 750 g/l (2007) / 750 g/l (2010) This product contains max. 565 g/l VOC.

Limitations

Do not apply when there is a risk of rain, air or substrate temperatures are likely to fall below 5ºC or when the relative humidity is above 80% during application or the drying period. Do not apply to bitumen coatings. The decoration of Fletton brickwork either facings or commons is not recommended.

PREPARATION New Surfaces

All surfaces must be sound, suitably dry and free from anything that will interfere with the adhesion of the material to be applied. Surfaces with suction (porous surfaces) should be treated with an application of Albany Stabilising Solution.

Undecorated Surfaces

All surfaces must be sound, suitably dry and free from anything that will interfere with the adhesion of the materials to be applied. Remove all organic growth by scraping or brushing with a stiff bristle brush (not wire). Heavy long established growth is best removed by pressure washing between 1500-2000 psi (102-136 bar), wet or dry grit blasting. Care must be taken not to damage the underlying surface. The spores must be killed with an application of Albany Fungicidal Wash diluted one volume of Fungicidal Solution with up to four volumes clean water. Leave for 24 hours and rinse with clean water. Allow to dry. Fill cracks and small defects in masonry surfaces with a suitable proprietary filler and finish to match existing. Stabilise all bare, filled and decorated chalking areas with an application of Albany Stabilising Solution.

Technical Data Sheet

Previously Decorated Surfaces

All surfaces must be sound, suitably dry and free from anything that will interfere with the adhesion of the material to be applied. Remove all loose, and failing or suspect material by scraping or brushing with a stiff bristle brush (not wire) to a sound edge. Organic growth must be removed and the areas treated with Albany Fungicidal Wash. For surfaces in poor condition mechanical means may be necessary e.g. pressure washing between 1500-2000 psi (102-136 bar), proprietary paint removal system, wet or dry grit blasting. Care must be taken not to damage the underlying surface. Fill cracks and surface defects in masonry surfaces with a suitable proprietary filler and finish to match existing. Stabilise all bare, filled and previously decorated chalking areas with an application of Albany Stabilising Solution.

COATING SYSTEM

Apply in one liberal coat until suction, porous, friable or chalking surfaces are stabilised. Do not over stabilise.

APPLICATION

Apply by brush.

CLEANING

Return surplus material to container. Clean with a proprietary cleaner immediately after use.

MAINTENANCE INFORMATION FOR CDM FILE HEALTH AND SAFETY

tanks.

GENERAL INFORMATION

E-mail enquiries@brewers.co.uk

Website www.brewers.co.uk

This information is correct at date of issue November 2009.

Albany House Ashford Road Eastbourne BN21 3TR Tel 01323 411080 Fax 01323 721435 E-mail: enquiries@brewers.co.uk Website: www.brewers.co.uk 54

Technical Data Sheet

ALBANY UNDERCOAT An excellent foundation for Albany Gloss. For new work and redecoration.

AVAILABILITY Colour Range

Refer to current Albany literature.

Packaging

1, 2.5 and 5 litres.

PROPERTIES Drying Time

Under normal drying conditions surface dry 4 hours and recoatable after 16 hours. Allow for adequate ventilation during the drying period.

Finish

Matt.

Composition

Pigment: Titanium Dioxide, coloured pigments and extenders Resin: Long Oil Alkyd Solvent: Dearomatised White Spirit

Spreading Rate

Up to 16m² per litre depending on surface texture.

Wet Film Thickness

63 micrometres at 15m² per litre.

Dry Film Thickness

39 micrometres at 15m² per litre.

Volume Solids

62.47% White . Other colours will vary.

Flash Point

40ºC (closed cup).

VOC Content

EU limit value for this product (cat.A/d): 400 g/l (2007) / 300 g/l (2010) This product contains max. 399 g/l VOC.

Limitations

Do not apply when air or substrate temperatures are likely to fall below 5ºC or when the relative humidity is above 80% during application or the drying period.

PREPARATION New Surfaces Timber

All Metals including Galvanised

Additional Surface Preparation - All Metals Non-Ferrous Metals Lightly abrade to a bright (not polished) surface - excluding galvanised surfaces. Rinse thoroughly with clean water to remove all resides. Allow to dry. Prime, including gal vanised surfaces, with one coat of Albany All Purpose Primer.

Technical Data Sheet

Ferrous Metals Previously Decorated Surfaces - Timber

All surfaces must be suitably dry, and free from anything that will interfere with the adhesion of the materials to be applied. Remove all loose, and failing or suspect paint. Prior to painting the moisture should not exceed 18%. Remove grey and denatured sur faces by rubbing down with abrasive paper or by mechanical means and round sharp edges 1-3mm. Feather edges of sound paint. Remove all dust. Organic growth must be removed and the areas treated with Crown Trade Fungicidal Solution. Remove any defective putty glazing, clean and prime rebates, replacement putties must be allowed to form a hard skin. Treat knots with two thin coats of fresh knotting. Fill any fixing holes, open joints and shallow surface defects with a suitable proprietary filler or a two pack proprietary wood filler. Rub down with a suitable grade of abrasive paper. Remove all dust.

Metals

Timber and Metals

COATING SYSTEM

Apply two coats as required.

APPLICATION

Stir well before use. Apply by brush to an even thickness (a fine, soft long filament bristle brush gives best results). Maintain a wet edge. On timber lay off in the direction of the grain.

MAINTENANCE INFORMATION FOR CDM FILE HEALTH AND SAFETY

Remove all millscale and rust back to clean metal. Remove all residues. Prime within the working day with one coat of Albany Metal Primer.

Technical Data Sheet

GENERAL INFORMATION

Albany House Ashford Road Eastbourne BN21 3TR Tel 01323 411080 Fax 01323 721435 E-mail: enquiries@brewers.co.uk Website: www.brewers.co.uk 57

Technical Data Sheet

ALBANY VINYL MATT EMULSION A durable full bodied matt finish with good obliteration.

AVAILABILITY Colour Range

Refer to current Albany literature.

Packaging

1, 2.5, 5 litres, (10 litres Brilliant White & Magnolia).

PROPERTIES Drying Time

Under normal drying conditions touch dry 2 hours, recoatable after 4 hours. Allow for adequate ventilation during the drying period.

Finish

Matt.

Composition

Pigment: Titanium Dioxide, coloured pigments and extenders Binder: Vinyl acetate copolymer Solvent: Water

Spreading Rate

Up to 16m² per litre on smooth surfaces.

Wet Film Thickness

62 micrometres at 16m² per litre.

Dry Film Thickness

19 micrometres at 16m² per litre.

Volume Solids

30% Brilliant White other colours will vary.

Flash Point

Not applicable.

VOC Content

EU limit value for this product (cat.A/a): 75 g/l (2007) / 30 g/l (2010) This product contains max. 1 g/l VOC.

Limitations

For interior use only. Do not apply when air or substrate temperatures are likely to fall below 8ºC or when the relative humidity is above 80% during application or the drying period.

PREPARATION New Surfaces

Previously Decorated Surfaces

All surfaces must be sound, clean, suitably dry and free from anything that will interfere with the adhesion of the materials to be applied. Powdery, polished plaster or dense surfaces should be primed with Albany Primer Sealer. Porous surfaces should be ‘mist’ coated with Albany Vinyl Matt Emulsion thinned with up to 20% clean water.

Technical Data Sheet

COATING SYSTEM

Apply two coats as required.

APPLICATION

Stir well before use. Apply by brush, roller or spray. For spray application dilution may be required.

CLEANING

Return surplus material to container. Wash with clean water immediately after use.

MAINTENANCE INFORMATION FOR CDM FILE HEALTH AND SAFETY

GENERAL INFORMATION

Apply all products in accordance with BS 6150: 2006 Code of practice for painting of buildings and BS 8000: Part 12: 1989 Code of practice for decorative wallcoverings and painting. Under normal and frost free conditions this product will remain usable for up to two years if stored correctly and unopened. Every care is taken to ensure that all information provided on this Technical Data Sheet is accurate. Brewers Ltd are unable to guarantee results as it has no control over the conditions under which its products are applied.

Albany House Ashford Road Eastbourne BN21 3TR Tel 01323 411080 Fax 01323 721435 E-mail: enquiries@brewers.co.uk Website: www.brewers.co.uk 60

Technical Data Sheet

ALBANY VINYL SILK EMULSION An attractive even sheen with excellent colour retention.

AVAILABILITY Colour Range

Refer to current Albany literature.

Packaging

2.5, 5 litres, (10 litres Brilliant White & Magnolia)

PROPERTIES Drying Time

Under normal drying conditions touch dry 2 hours, recoatable after 4 hours. Allow for adequate ventilation during the drying period.

Finish

Silk.

Composition

Pigment: Titanium Dioxide, coloured pigments and extenders Binder: Vinyl acetate copolymer Solvent: Water

Spreading Rate

Up to 15m² per litre on smooth surfaces.

Wet Film Thickness

67 micrometres at 15m² per litre.

Dry Film Thickness

17 micrometres at 15m² per litre.

Volume Solids

25.01% Brilliant White other colours will vary.

Flash Point

Not applicable.

VOC Content

EU limit value for this product (cat.A/b): 150 g/l (2007) / 100 g/l (2010) This product contains max. 2 g/l VOC.

Limitations

For interior use only. Do not apply when air or substrate temperatures are likely to fall below 8ºC or when the relative humidity is above 80% during application or the drying period.

PREPARATION New Surfaces

Previously Decorated Surfaces

All surfaces must be sound, clean, suitably dry and free from anything that will interfere with the adhesion of the materials to be applied. Powdery, polished plaster or dense surfaces should be primed with Albany Primer Sealer. Porous surfaces should be ‘mist’ coated with Albany Vinyl Silk Emulsion thinned with up to 10% clean water.

Technical Data Sheet

COATING SYSTEM

Apply two coats as required.

APPLICATION

Stir well before use. Apply by brush, roller or spray. For spray application dilution may be required.

CLEANING

Return surplus material to container. Wash with clean water immediately after use.

MAINTENANCE INFORMATION FOR CDM FILE HEALTH AND SAFETY

GENERAL INFORMATION

Albany House Ashford Road Eastbourne BN21 3TR Tel 01323 411080 Fax 01323 721435 E-mail: enquiries@brewers.co.uk Website: www.brewers.co.uk 62

Technical Data Sheet

ALBANY WOOD PRIMER For non resinous softwood joinery.

AVAILABILITY Colour Range

White and Pink.

Packaging

500ml, 1, 2.5 and 5 litre.

PROPERTIES Drying Time

Under normal drying conditions surface dry 4 hours and recoatable after 16 hours. Allow for adequate ventilation during the drying period.

Finish

Eggshell.

Composition

Pigment: Titanium Dioxide and extenders Resin: Long Oil Alkyd Solvent: Dearomatised White Spirit

Spreading Rate

Up to 15m² per litre depending on surface texture.

Wet Film Thickness

66 micrometres at 15m² per litre.

Dry Film Thickness

38 micrometres at 15m² per litre.

Volume Solids

57%.

Flash Point

40ºC (closed cup).

VOC Content

EU limit value for this product (cat.A/d): 450 g/l (2007) / 350 g/l (2010) This product contains max. 333 g/l VOC.

Limitations

Do not apply when air or substrate temperatures are likely to fall below 5ºC or when the relative humidity is above 80% during application or the drying period.

PREPARATION New Surfaces

must

Previously Decorated Surfaces

All surfaces must be suitably dry, and free from anything that will interfere with the adhesion of the materials to be applied. Rub down with a suitable grade of abrasive paper and round sharp edges 1-3mm. Remove all dust. Timber with oils/extractives be swabbed with clean dearomatised white spirit, frequently changing the face of the cloths. Treat knots with two thin coats of fresh knotting. Fill any fixing holes, open joints and shallow surface defects with a suitable proprietary filler. Rub down with a suitable grade of abrasive paper.

All surfaces must be suitably dry, and free from anything that will interfere with the adhesion of the materials to be applied. Remove all loose, and failing or suspect paint. Remove grey and denatured surfaces by rubbing down with abrasive paper or by mechanical means and round sharp edges 1-3mm. Feather edges of sound paint. Remove all dust. Organic growth must be removed and the areas treated with Albany Fungicidal Wash. Remove any defective putty glazing, clean and prime rebates, replacement putties must be allowed to form a hard skin. Treat knots with two thin coats of fresh knotting. Fill any fixing holes, open joints and shallow surface defects with a suitable proprietary filler. or a two pack proprietary wood filler. Rub down with a suitable grade of abrasive paper. Remove all dust. Wash remaining sound paint with hot water and liquid detergent solution to remove any contaminants, frequently changing the water. Wet abraded to provide a key. Rinse with clean water to remove all residues. Allow to dry. Spot prime all bare and filled areas.

Technical Data Sheet

COATING SYSTEM

Apply one coat.

APPLICATION

Stir well before use. Apply by brush or roller in the direction of the grain. Prior to priming, the moisture content of the substrate should not exceed 18%.

CLEANING

Return surplus material to container. Clean with a proprietary cleaner immediately after use.

MAINTENANCE INFORMATION FOR CDM FILE HEALTH AND SAFETY

GENERAL INFORMATION

Albany House Ashford Road Eastbourne BN21 3TR Tel 01323 411080 Fax 01323 721435 E-mail: enquiries@brewers.co.uk Website: www.brewers.co.uk 64

Technical Data Sheet

ALBANY YACHT VARNISH Albany Yacht Varnish is specially formulated for use on interior and exterior woodwork to provide a clear high build gloss finish. It is suitable for timber which is exposed to marine environments but not for timber continuously immersed in salt or fresh water.

AVAILABILITY Colour

Clear.

Packaging

1 and 2.5 litres.

PROPERTIES Drying Time

Under normal drying conditions touch dry in 4-6 hours, recoatable after 16-24 hours. Allow for adequate ventilation during the drying period.

Finish

Gloss.

Composition

Resin: Urethane and Alkyd Resins Solvent: Dearomatised White Spirit

Spreading Rate

Up to13m² per litre depending on surface texture.

Wet Film Thickness

76 micrometres at 13m² per litre.

Dry Film Thickness

38 micrometres at 13m² per litre.

Volume Solids

50% Brilliant White. Other colours will vary.

Flash Point

60ºC. (closed cup).

VOC Content

EU limit value for this product (cat.A/e): 500 g/l (2007) / 400 g/l (2010) This product contains max. 399 g/l VOC.

Limitations

Do not apply when air or substrate temperatures are likely to fall below 5ºC or when the relative humidity is above 80% during application or the drying period.

PREPARATION New Surfaces Timber

All surfaces must be suitably dry, and free from anything that will interfere with the adhesion of the materials to be applied. Rub down with a suitable grade of abrasive paper and round sharp edges 1-3mm. Remove all dust. Timber with oils/extractives must be swabbed with clean methylated spirits, frequently changing the face of the cloths. Fill any fixing holes, open joints and shallow surface defects with a suitable proprietary wood filler to match the colour of the bare timber. Rub down with a suitable grade of abrasive paper. Remove all dust.

Previously varnished surfaces

All surfaces must be suitably dry, and free from anything that will interfere with the adhesion of the materials to be applied. Remove all loose, and failing or suspect varnish and any grey denatured timber. Prior to coating, the moisture should not exceed 18%. Feather edges of sound varnish. Remove all dust. Organic growth must be removed and the areas treated with Albany Fungicidal Wash. Fill any fixing holes, open joints and shallow surface defects with a suitable proprietary wood filler to match the colour of the bare timber. Rub down with a suitable grade of abrasive paper. Remove all dust. Spot varnish bare and filled areas with Albany Yacht Varnish. Wash remaining sound varnish with hot water and liquid detergent solution to remove any contaminants, frequently changing the water. Wet abraded to provide a key. Rinse with clean water to remove all residues. Allow to dry. Bring forward spot primed areas with one coat of the Albany Yacht Varnish.

Technical Data Sheet

COATING SYSTEM

Apply two or three full coats as required. Maintain a wet edge.

APPLICATION

Stir well before use. Apply by brush to an even thickness (a fine, soft long filament bristle brush gives best results). Maintain a wet edge. On timber lay off in the direction of the grain.

CLEANING

Return surplus material to container. Clean with a proprietary cleaner immediately after use.

MAINTENANCE INFORMATION FOR CDM FILE HEALTH AND SAFETY

GENERAL INFORMATION

Albany House Ashford Road Eastbourne BN21 3TR Tel 01323 411080 Fax 01323 721435 E-mail: enquiries@brewers.co.uk Website: www.brewers.co.uk 66