S E R I E S
Catalog 2006
60
1 Cylinders Series 60
C Y L I N D E R S
Single and double–acting (magnetic) (DIN/ISO 6431) Bore: ø 32, 40, 50, 63, 80, 100,125 cushioned [1 1/4”, 1 9/16”, 2”, 2 1/2”, 3 1/8”, 4”, 5” inch approximations] The Series 60 cylinders with diameters 32, 40, 50, 63, 80, 100 and 125 have been designed to comply with the dimensions laid down in the DIN/ISO 6431 standards. A removeable magnet is mounted on the piston in these cylinders. This cylinders series is normally equipped with adjustable end–stroke cushioning. Moreover these cylinders are equipped with a mechanical cushioning in order to reduce the impact of the piston as it reaches the end of the stroke. These cylinders can also accommodate stroke lengths up to 1000 mm for bore sizes shown in the table.
DIN/ISO 6431 VDMA 24562 Rolled stainless steel rod GENERAL DATA
Type of construction Operation Materials Type of mounting Max. strokes Bore Ports Assembly position Operating temperature Special design
with tie–rods double–acting, single–acting, tandem aluminum end–blocks, Buna–N seals, others parts see coding with tie–rods, front flange, rear flange, feet, center trunnion, front and rear trunnion, swivel combination 10 – 2500mm ø 32, 40, 50, 63, 80, 100, 125 32 = 1/8; 40–50 = 1/4; 63/80 = 3/8; 100/125 = 1/2 any position 0 – 80°C (with dry air – 20°C), 32°F – 175°F (dry air – 4°F) for use in damp, dusty and aggressive environments
The company reserves the right to vary models and dimensions without notice. These products are designed for industrial applications and are not suitable for sale to the general public.
Dimensions are in millimeters, inch notations are approximate for bore sizes.
1.32
60
S E R I E S
Catalog 2006
1
C Y L I N D E R S
PNEUMATIC DATA
Operating pressure Speed Fluid
1 – 10 bar [Min.1 bar (14.5psi); Max. 10 bar (145 psi)] 10 – 1000 mm/sec (No load) [Min. 10 mm/sec(No load); Max ≤ 1000mm/sec (No load)] clean air, without lubrication*
*If lubricated air is used, it is recommended to use oil ISOVG32. Once applied the lubrication should never be interrupted.
CYLINDER CODING
60M2L 050A0200 SERIES 60 = from ø 32 – 125 DIN/ISO 6431
VERSIONS M = magnetic N = non magnetic
OPERATION 1 = single–acting (front spring) 2 = double–acting (front and rear cushions) 3 = double–acting (no cushion) 4 = double–acting (rear cushion) 5 = double–acting (front cushion) 6 = double–acting (double–rod with front and rear cushions) 7 = single–acting (double–rod)
STROKE (see table)
BORE 32 mm 40 mm 50 mm 63 mm
S V N R W
= = = = =
special to be indicated viton rod seal tandem Buna–N rod seal all seals in viton
TYPE OF BRACKET A = standard with lock nut for rod F = centre trunnion RL = cylinder with rod lock 80 mm 100 mm 125 mm
MATERIALS L = rolled stainless steel rod – anodized aluminum round tube Buna–N seals – nuts and tie rods zinc–plated steel – rod seals polyurethane * T = rolled stainless steel rod – anodized aluminum round tube – Buna–N seals – rod seals polyurethane – nuts and tie–rods stainless steel * on request 60M2L = standard version in stock (32 –125) Note: The accessories are not mounted on the cylinders
1.33
Dimensions are in millimeters, inch notations are approximate for bore sizes.
The company reserves the right to vary models and dimensions without notice. These products are designed for industrial applications and are not suitable for sale to the general public.
S E R I E S
Catalog 2006
60
1 CHARACTERISTICS OF SINGLE–ACTING CYLINDERS SERIES 60–61 Force in N x D.245 = 1bf
ø
10 10 10 10 10 10
– – – – – –
75 75 75 75 75 75
Extend N at 6 bar 425 664 1037 1650 2660 4154
Force of spring at rest N (stroke 75 mm) 31 35 60 60 84 84
Force of compressed spring N 57 57 115 115 133 133
NOTE : the Series 60 – 61 single–acting cylinders’ dimensions for L1 and L2 are to be increased by 25 mm.
The company reserves the right to vary models and dimensions without notice. These products are designed for industrial applications and are not suitable for sale to the general public.
Dimensions are in millimeters, inch notations are approximate for bore sizes.
C Y L I N D E R S
32 40 50 63 80 100
min–max stroke
1.34
S E R I E S
60
Catalog 2006
1
C Y L I N D E R S
TABLE SHOWING AIR CONSUMPTION OF SERIES 60
ø Cyl in mm.
ø Rod in mm.
32
12
40
16
50
20
63
20
80
25
100
25
125
32
Working area in cm 2. Extend side Retract side Extend side Retract side Extend side Retract side Extend side Retract side Extend side Retract side Extend side Retract side Extend side Retract side
8.03 6.9 12.56 10.56 19.6 16.48 31.15 28 50.25 45.35 78.5 73.6 122.65 115.6
1
2
3
0.016 0.014 0.025 0.021 0.039 0.033 0.062 0.056 0.101 0.091 0.157 0.147 0.245 0.229
0.024 0.021 0.038 0.032 0.059 0.050 0.094 0.084 0.151 0.136 0.235 0.221 0.368 0.344
0.032 0.028 0.050 0.042 0.079 0.066 0.125 0.112 0.201 0.181 0.314 0.295 0.491 0.459
THE VALUES SHOWN IN THE TABLE WERE OBTAINED USING THE FOLLOWING FORMULA: Qs = consumption on extend side D = diameter on extend side in cm.
Qt = consumption on retract side d = rod diameter in cm.
Qs =
Operating pressure in bar 4 5 6 7 8 Air consumption in NL for each 10 mm. of stroke 0.040 0.048 0.056 0.064 0.072 0.035 0.042 0.048 0.055 0.062 0.063 0.075 0.088 0.100 0.113 0.053 0.063 0.074 0.085 0.095 0.098 0.118 0.137 0.157 0.177 0.083 0.099 0.115 0.132 0.148 0.156 0.187 0.218 0.249 0.280 0.140 0.168 0.196 0.224 0.252 0.251 0.302 0.352 0.402 0.452 0.227 0.272 0.317 0.363 0.408 0.392 0.471 0.550 0.628 0.707 0.368 0.441 0.515 0.589 0.663 0.614 0.736 0.859 0.982 1.104 0.573 0.688 0.803 0.917 1.032
D 2 . π . (P + 1) 4 . 1000
.H
Qn = (Qs+Qt) · n
Qn = consumption of cylinder H = cylinder stroke in cm.
Qt =
9
10
0.080 0.069 0.126 0.106 0.196 0.165 0.312 0.280 0.503 0.454 0.785 0.736 1.227 1.147
0.088 0.076 0.138 0.116 0.216 0.182 0.343 0.308 0.553 0.499 0.864 0.810 1.350 1.261
(D 2 – d 2) . π . (P + 1) 4 . 1000
.H
n = number of cycles per minute P = operating pressure in bar
TABLE SHOWING THE OUTPUT FORCE OF SERIES 60
ø Cyl. in mm.
ø Rod in mm.
32
12
40
16
50
20
63
20
80
25
100
25
125
32
Working area in cm 2. Extend side Retract side Extend side Retract side Extend side Retract side Extend side Retract side Extend side Retract side Extend side Retract side Extend side Retract side
8.03 6.9 12.56 10.56 19.6 16.48 31.15 28 50.25 45.35 78.5 73.6 122.65 115.6
1
2
70 60 110 93 173 145 275 247 443 400 692 650 1090 1019
140 120 220 186 346 290 550 494 886 800 1385 1300 2180 2037
THE VALUES SHOWN IN THE TABLE WERE OBTAINED USING THE FOLLOWING FORMULA: Ss = output force on extend side St = forza sviluppata lato trazione
P = operating pressure in bar D = diameter on extend side in cm.
Ss =
3
4 5 Output force in N (efficiency 210 283 354 180 243 305 330 443 554 280 375 465 518 692 865 436 582 727 824 1098 1373 740 988 1235 1330 1772 2216 1200 1600 2000 2077 2770 3460 1948 2608 3245 3270 4360 5450 3056 4075 5093 D2 . π
.P.η
4
Operating pressure in bar 6 7 8 9 factor 0,9) 425 494 595 635 365 426 487 548 664 775 886 998 559 652 745 838 1037 1210 1382 1556 872 1017 1163 1308 1650 1923 2198 2472 1480 1729 1976 2222 2660 3100 3545 3990 2400 2800 3200 3600 4154 4847 5540 6320 3895 4544 5193 5842 6540 7631 8721 9811 6112 7130 8149 9168
St =
(D 2 – d 2) . π 4
10 706 608 1108 931 1729 1454 2747 2470 4432 4000 6923 6492 10901 10186
.P.η
d = rod diameter in cm η = efficiency factor
TORQUE FORCE BRACKETS SERIES 60
Cylinder bore Max. torque force brackets
1.35
32 6Nm
40 6Nm
50 13Nm
Dimensions are in millimeters, inch notations are approximate for bore sizes.
63 13Nm
80 19Nm
100 22Nm
125 26Nm
The company reserves the right to vary models and dimensions without notice. These products are designed for industrial applications and are not suitable for sale to the general public.
S E R I E S
Catalog 2006
60
1 Cylinders Series 60
DIMENSIONS Bd
KK
11
ø
MM
32 40 50 63 80 100 125
12 M10x1,25 30 14 16 M12x1,25 35 15 20 M16x1,5 40 15 20 M16x1,5 45 21 25 M20x1,5 45 21 25 M20x1,5 55 23 32 M27x2 60 23,5
PL
L1
AM VA
18 21 25 26 30 35 42
22 24 32 32 40 40 54
4 4 4 4 4 4 6
EE
WH
L2
ZJ
VD
G1/8 G1/4 G1/4 G3/8 G3/8 G1/2 G1/2
26 30 37 37 46 51 65
94 105 106 121 128 138 160
120 135 143 158 174 189 225
5 5 6 6 7 7 8
N
BG
RT
26 16 M6 29 16 M6 29,5 16 M8 36,5 16 M8 36 19 M10 38,5 19,5 M10 43 23 M12
G
TG
R
E
SW1 SW2 SW3 SW4 Cushion stroke 5 32,5 13 46 10 6 2 17 19 5 38 13,5 55 13 6 2 19 22 8 46,5 16 64,5 17 8 3 24 22 8 56,5 28 75 17 8 3 24 22 8 72 30 93 22 10 5 30 25 8 89 40 110 22 10 5 30 25 10,5 110 50 135 27 12 4 41 43
C Y L I N D E R S
+ add the stroke
N.B. : the single-acting cylinders’ sizes L1 and L2 are increased by 25 mm.
Cylinders Series 60 Double-rod
+ add the stroke ++ add the stroke two times
DIMENSIONS KK
Bd
11
ø
MM
32 40 50 63 80 100 125
12 M10x1,25 30 14 16 M12x1,25 35 15 20 M16x1,5 40 15 20 M16x1,5 45 21 25 M20x1,5 45 21 25 M20x1,5 55 23 32 M27x2 60 23,5
PL
L1
AM
EE
18 21 25 26 30 35 42
22 G1/8 24 G1/4 32 G1/4 32 G3/8 40 G3/8 40 G1/2 54 G1/2
WH
L2
ZM
VD
26 30 37 37 46 51 65
94 105 106 121 128 138 160
146 165 180 195 220 240 290
5 5 6 6 7 7 8
N
RT
BG
G
TG
R
E
26 M6 16 5 32,5 13 46 29 M6 16 5 38 13,5 55 29,5 M8 16 8 46,5 16 64,5 36,5 M8 16 8 56,5 28 75 36 M10 19 8 72 30 93 38,5 M10 19,5 8 89 40 110 43 M12 23 10,5 110 50 135
SW1 SW2 SW3 10 13 17 17 22 22 27
6 6 8 8 10 10 12
2 2 3 3 5 5 4
SW4 Cushion stroke 17 19 19 22 24 22 24 22 30 25 30 25 41 43
N.B. : the single-acting cylinders’ sizes L1 and L2 are increased by 25 mm.
The company reserves the right to vary models and dimensions without notice. These products are designed for industrial applications and are not suitable for sale to the general public.
Dimensions are in millimeters, inch notations are approximate for bore sizes.
1.36
S E R I E S
60
Catalog 2006
1 Cylinders Series 60 tandem + add the stroke ++ add the stroke two times
C Y L I N D E R S
DIMENSIONS ø 32 40 50 63 80 100 125
EE G1/8 G1/4 G1/4 G3/8 G3/8 G1/2 G1/2
L2 171,5 191,5 188 204 225,5 231 264
L3 197,5 221,5 225 230 271,5 282 329
Cylinders Series 60 with rod lock
+ add the stroke
DIMENSIONS ø
L1
L2
L3
L4
L5
L6
L7
L8
L9
L10
øD
øD1 d11 øD2
øD3 f8
A ±0.15
G
H
H1
M
Z
32 40 50 63 80 100 125
58 65 82 82 110 115 167
48 55 70 70 90 100 122
10 10 12 12 20 15 45
8 8 15 15 18 18 22
13 13 16 16 20 20 30
20,5 22,5 29,5 29,5 35 39 51
34 38 48 49,5 61 69 86,5
45 50 60 70 90 105 140
94 105 106 121 128 138 160
160 178 200 215 254 269 350
12 16 20 20 25 25 32
30,5 35 35 40 40 50 45 60 45 80 55 100 60 130
25 28 35 38 48 58 65
32,5 38 46,5 56,5 72 89 110
M5 G1/8 G1/8 G1/8 G1/8 G1/8 G1/8
25,5 30 36 40 50 58 80
46,5 53 64 75 95 110,5 150
M6 M6 M8 M8 M10 M10 M12
M6 x 20 M6 x 20 M8 x 30 M8 x 30 M10 x 35 M10 x 35 M12 x 40
Cylinders Series 60 with centre trunnion 60M2L... F...
+ add the stroke
DIMENSIONS ø 32 40 50 63 80 100 125
1.37
XV1 ± 2 63,5 72,5 79,5 88 97 102 121
XV2 ± 2 73 82,5 90 97,5 110 120 145
XV3 ± 2 82,5 92,5 100,5 107 123 138 169
f 32,5 38 46,5 56,5 72 89 110
TM h14 50 63 75 90 110 132 160
Dimensions are in millimeters, inch notations are approximate for bore sizes.
h 20 25 25 30 30 30 30
TD e9 12 16 16 20 20 25 25
TL h14 12 16 16 20 20 25 25
UW 65 74 85 100 120 135 160
R 0,1 0,15 0,15 0,15 0,15 0,2 0,2
The company reserves the right to vary models and dimensions without notice. These products are designed for industrial applications and are not suitable for sale to the general public.
S E R I E S
Catalog 2006
60
1 Foot mount Mod. B..
+ add the stroke
DIMENSIONS Mod. B-41-32 B-41-40 B-41-50 B-41-63 B-41-80 B-41-100 B-41-125
ø 32 40 50 63 80 100 125
AT 4 4 4 5 6 6 7
SA ± 1.25 142 161 170 185 210 220 250
XA ± 1.25 144 163 175 190 216 230 270
TR JS14 E AB AH JS16 32 45 7 32 36 53,5 10 36 45 62,5 10 45 50 73 10 50 63 92 12 63 75 108,5 14,5 71 90 132 16,5 90
AO 11 15 15 15 20 25 25
AU 24 28 32 32 41 41 45
Torque force (max) 6 Nm 6 Nm 13 Nm 13 Nm 19 Nm 22 Nm 26 Nm
C Y L I N D E R S
Material: zinc-plated steel. The following is supplied: N° 2 feet N° 4 screws
Front and rear flange Mod. D-E... Material: aluminium. The following is supplied: N° 1 flange N° 4 screws
+ add the stroke
DIMENSIONS Mod. D-E-41-32 D-E-41-40 D-E-41-50 D-E-41-63 D-E-41-80 D-E-41-100 D-E-41-125
ø 32 40 50 63 80 100 125
W ±2 16 20 25 25 30 35 45
MF 10 10 12 12 16 16 20
ZB JS14 120 135 143 158 174 189 225
TF JS14 64 72 90 100 126 150 180
R JS14 32 36 45 50 63 75 90
UF 86 88 110 116 148 176 224
The company reserves the right to vary models and dimensions without notice. These products are designed for industrial applications and are not suitable for sale to the general public.
E 45 52 63 73 95 115 135
FB H13 7 9 9 9 12 14 16
ZF ±1.25 130 145 155 170 190 205 245
Torque force (max) 6 Nm 6 Nm 13 Nm 13 Nm 19 Nm 22 Nm 26 Nm
Dimensions are in millimeters, inch notations are approximate for bore sizes.
1.38
S E R I E S
60
Catalog 2006
1
C Y L I N D E R S
Rear trunnion, female Mod. C...... and CH... Material: aluminium. The following is supplied: N° 1 female trunnion N° 4 screws
+ add the stroke
DIMENSIONS Mod. C-41-32 C-41-40 C-41-50 C-H-41-63 C-H-41-80 C-H-41-100 C-H-41-125
ø 32 40 50 63 80 100 125
CD H 9 10 12 12 16 16 20 25
FL 12 15 15 20 24 29 30
C 22 25 27 32 36 41 50
XD ±1.6 142 160 170 190 210 230 275
MR 10 13 13 15 15 18 25
E 45 52 63 73 95 115 135
CB H 14 26 28 32 40 50 60 70
UB h 14 45 52 60 70 90 110 130
G 45 52 63 73 95 115 135
CB H14 26 28 32 40 50 60 70
UB h14 45 52 60 70 90 110 130
Torque force (max) 6 Nm 6 Nm 13 Nm 13 Nm 19 Nm 22 Nm 26 Nm
Front trunnion female Mod. H... and C-H... Material: aluminium. The following is supplied: N° 2 female trunnions N° 4 screws
+ add the stroke
DIMENSIONS Mod. H-41-32 H-41-40 H-41-50 H-60-63 C-H-41-80 C-H-41-100 C-H-41-125
1.39
ø 32 40 50 63 80 100 125
CD H 9 10 12 12 16 16 20 25
E 16 20 25 25 34 39 45
H 4 5 10 5 10 10 15
D 120 135 143 158 174 189 225
MR 10 13 13 15 15 18 25
F 32,5 38 46,5 56,5 72 89 110
Dimensions are in millimeters, inch notations are approximate for bore sizes.
The company reserves the right to vary models and dimensions without notice. These products are designed for industrial applications and are not suitable for sale to the general public.
S E R I E S
Catalog 2006
60
1 Rear trunnion, male Mod. L...
C Y L I N D E R S
Material: aluminium. The following is supplied: N° 2 male trunnion N° 4 screws
+ add the stroke
DIMENSIONS ø CD H 9 32 10 40 12 50 12 63 16 80 16 100 20 125 25
Mod. L-41-32 L-41-40 L-41-50 L-41-63 L-41-80 L-41-100 L-41-125
L 12 15 15 20 24 29 30
FL 22 25 27 32 36 41 50
XD ± 1.6 142 160 170 190 210 230 275
MR 9 13 13 15 15 18 25
E 45 52 63 73 95 115 135
-0.2 EW -0.6 26 28 32 40 50 60 70
Torque force (max) 6 Nm 6 Nm 13 Nm 13 Nm 19 Nm 22 Nm 26 Nm
Centre trunnion Mod. F... Material: zinc-plated steel. The following is supplied: N° 1 intermediate trunnion N° 4 clamping elements N° 4 locking screws
+ add the stroke
DIMENSIONS Mod. F-32 F-40 F-50 F-63 F-80 F-100 F-125
ø 32 40 50 63 80 100 125
XV ± 2 63,5 72,5 79,5 88 97 102 121
XV1± 2 73 82,5 90 97,5 110 120 145
XV2 ± 2 82,5 92,5 100,5 107 123 138 169
TM h14 50 63 75 90 110 132 160
TK 20 25 25 30 30 30 30
TD e9 12 16 16 20 20 25 25
The company reserves the right to vary models and dimensions without notice. These products are designed for industrial applications and are not suitable for sale to the general public.
TL h14 12 16 16 20 20 25 25
UW 65 74 85 100 120 135 160
R 0,1 0,15 0,15 0,15 0,15 0,2 0,2
Dimensions are in millimeters, inch notations are approximate for bore sizes.
1.40
S E R I E S
60
Catalog 2006
1 Accessory combination Mod.C+L+S
C Y L I N D E R S
Material: aluminium.
+ add the stroke
DIMENSIONS ø CD H 9 32 10 40 12 50 12 63 16 80 16 100 20 125 25
L 12 15 15 20 24 29 30
FL 22 25 27 32 36 41 50
XD ±1.6 142 160 170 190 210 230 275
TG 32,5 38 46,5 56,5 72 89 110
E 45 52 63 73 95 115 135
l 10 10 12 12 12 12 20
M 22 25 27 32 36 41 50
N 6,5 6,5 9 9 11 11 13
Torque force (max) 6 Nm 6 Nm 13 Nm 13 Nm 19 Nm 22 Nm 26 Nm
90° male trunnion according to CETOP RP 107P Mod. ZC... Material: aluminium. The following is supplied: N° 1 male trunnion
+ add the stroke
DIMENSIONS Mod. ZC-32 ZC-40 ZC-50 ZC-63 ZC-80 ZC-100 ZC-125
1.41
ø EB H13 32 11 40 11 50 15 63 15 80 18 100 18 125 20
CK H9 HB H13 XD 10 6,6 154 12 6,6 173 12 9 188 16 9 209,5 16 11 237 20 11 260 25 14 315
TE JS14 UL MAX EA MAX GL JS14 38 51 10 21 41 54 15 24 50 65 16 33 52 67 16 37 66 86 20 47 76 96 20 55 94 124 30 70
Dimensions are in millimeters, inch notations are approximate for bore sizes.
L5 MAX RA JS14 1,6 18 1,6 22 1,6 30 1,6 35 2,5 40 2,5 50 3,2 60
EM 26 28 32 40 50 60 70
- 0,2 - 0,6
-0,5 -1,5
UR SJ14 PH JS15 31 32 35 36 45 45 50 50 60 63 70 71 90 90
BT 8 10 12 12 14 15 20
BR MAX 10 11 13 15 15 19 22,5
P P P P P P P
The company reserves the right to vary models and dimensions without notice. These products are designed for industrial applications and are not suitable for sale to the general public.
S E R I E S
Catalog 2006
60
1 Rear Trunnion ball - joint Mod. R*...
C Y L I N D E R S
Material: aluminium *not according to standard. The following is supplied: N° 1 trunnion ball joint N° 4 screws
+ add the stroke
DIMENSIONS Mod. R-41-32 R-41-40 R-41-50 R-41-63 R-41-80 R-41-100
ø 32 40 50 63 80 100
CX H 9 10 12 12 16 16 20
L 12 15 15 20 24 29
DL 22 25 27 32 36 41
XN ±1.6 142 160 170 190 210 230
MS 16 20 20 24 24 30
E 45 52 63 73 95 115
EX - 0.1 14 16 16 21 21 25
Z° 4 4 4 4 4 4
Torque force (max) 6 Nm 6 Nm 13 Nm 13 Nm 19 Nm 22 Nm
Counter bracket for centre trunnion Mod. BF... Material: aluminium. The following is supplied: N° 2 supports
DIMENSIONS Mod. BF-32 BF-40-50 BF-63-80 BF-100-125
ø 32 40-50 63-80 100-125
CR 12 16 20 25
NH 15 18 20 25
C 7,5 9 10 12,5
b3 3 3 3 3,5
TH 32 36 42 50
The company reserves the right to vary models and dimensions without notice. These products are designed for industrial applications and are not suitable for sale to the general public.
UL 46 55 65 75
FK 15 18 20 25
FN 30 36 40 50
B1 6,8 9 11 13
B2 11 15 18 20
HB 6,6 9 11 14
Dimensions are in millimeters, inch notations are approximate for bore sizes.
1.42
S E R I E S
60
Catalog 2006
1
C Y L I N D E R S
Example of assembly The mounting subbase Mod. PCV, enables the valve or solenoid valve to be mounted directly on the cylinder, thus forming a compact pneumatic operating unit which is easy to install. The subbase is fixed onto the cylinder using the screws Mod. 1635 or the unidirectional flow controllers, Mod. SCU.... The other end of the plate has a threaded port which allows the tube to be connected, by means of a fitting,to the other end-cap. Note: the minimum possible stroke is 100mm.
DIMENSIONS Mod. PCV-32 PCV-40-50 PCV-40-50 PCV-63-80 PCV-63-80
ø 32 40 50 63 80
A B C R G1/8 185 131,5 G1/8 G1/8 188,5 140,5 G1/4 G1/8 188,5 150 G1/4 G1/4 215 167 G1/4 G1/4 215 185 G1/4
S 16 16 16 16 16
d* G1/8 G1/4 G1/4 G3/8 G3/8
Valve Mod.** 458-015-22-S19 458-015-22-S19 458-015-22-S19 454-015-22S07 454-015-22S07
d* = mounting on the cylinder using Mod.1635 or Mod. SCU.
Valve Mod. ** = standard valves with end cap turned 180°
Rod Fork End G... ISO 8140. Material: zinc-plated steel. DIMENSIONS Mod. G-25-32 G-40 G-50-63 G-80-100 G-41-125
ø 32 40 50-63 80-100 125
øCK 10 12 16 20 30
LE 20 24 32 40 55
CM 10 12 16 20 30
CL 20 24 32 40 55
ER 12 14 19 25 38
CE 40 48 64 80 110
KK M10 x1,25 M12 x1,25 M16 x1,5 M20 x1,5 M27 x 2
B 26 32 40 48 74
øB1 18 20 26 34 48
Swivel Ball Joint Mod. GA... ISO 8139. Material: zinc-plated steel.
DIMENSIONS Mod GA-32 GA-40 GA-50-63 GA-80-100 GA-41-125
1.43
ø 32 40 50-63 80-100 125
ø CN H7 U EN 10 10,5 14 12 12 16 16 15 21 20 18 25 30 25 37
ER 14 16 21 25 35
AX CE KK 20 43 M10 x1,25 22 50 M12 x1,25 28 64 M16 x1,5 33 77 M20 x1,5 51 110 M27 x 2
Dimensions are in millimeters, inch notations are approximate for bore sizes.
øT 15 17,5 22 27,5 40
Z 6,5 6,5 7,5 7 7,5
SW 17 19 22 30 41
The company reserves the right to vary models and dimensions without notice. These products are designed for industrial applications and are not suitable for sale to the general public.
Catalog 2006
1 Piston Rod Socket Joint Mod. GY... Material: zama and zinc-plated steel.
C Y L I N D E R S
DIMENSIONS Mod. GY-25-32 GY-40 GY-50-63 GY-80-100
ø 32 40 50 - 63 80 - 100
KK M10 x 1,25 M12 x 1,25 M16 x 1,5 M20 x 1,5
L 74 84 112 133
CE 35 40 50 63
L2 6,5 6,5 8 10
AX 18 20 27 38
SW SW1 L1 17 11 19,5 19 17 22 22 19 27,5 30 24 31,5
L3 15 17 23 25
øT 15 17,5 22 27,5
øD 19 22 27 34
E 10 12 16 20
øB 14 19 22 29
øC 28 32 40 45
Z 15 15 11 7,5
Clevis Pin Mod. S...
Piston Rod Lock Nut Mod. U...
The following is supplied: N° 1 clevis pin (stainless steel 303) N° 2 Seeger (steel)
UNI EN ISO 4035. Material: zinc-plated steel. Included on Series 60 cylinders.
DIMENSIONS Mod. S-32 S-40 S-50 S-63 S-80 S-100 S-125
ø 32 40 50 63 80 100 125
d 10 12 12 16 16 20 25
L 52 59 67 77 97 121 140,5
L1 46 53 61 71 91 111 132
L2 H13 L3 1,1 3 1,1 3 1,1 3 1,1 3 1,1 3 1,3 5 1,3 4,25
The company reserves the right to vary models and dimensions without notice. These products are designed for industrial applications and are not suitable for sale to the general public.
DIMENSIONS Mod. U-25-32 U-40 U-50-63 U-80-100 U-41-125
ø 32 40 50-63 80-100 125
D M10x1,25 M12x1,25 M16x1,5 M20x1,5 M27x2
m 6 7 8 9 12
SW 17 19 24 30 41
Dimensions are in millimeters, inch notations are approximate for bore sizes.
1.44