61
S E R I E S
Catalog 2006
1
C Y L I N D E R S
Cylinders Series 61 Single, double–acting, magnetic (DIN/ISO 6431) Bore: ø 32, 40, 50, 63, 80, 100, 125 cushioned [1 1/4”, 1 9/16”, 2”, 2 1/2”, 3 1/8”, 4”, 5” inch approximations] The Series 61 cylinders with diameters 32, 40, 50, 63, 80, 100 and 125 have been designed to comply with the dimensions laid down in the DIN/ISO 6431 standards. The extruded aluminum tube with improved aesthetics, has two grooves (on three sides) where the proximity switch Mod. CST can be directly mounted. This enables the same cylinder dimensions to be retained. Four tie–rods located inside of the tube make the mounting of the end–blocks extremely secure. This cylinder series is equipped with adjustable end–stroke cushioning. Moreover, these cylinders are also equipped with a mechanical cushioning in order to reduce the impact of the piston as it reaches the end of the stroke (only until ø100). The cylinder series can also accommodate stroke lengths up to 1000 mm for bore sizes shown in the table.
DIN/ISO 6431/VDMA 24562 High durability Clean design GENERAL DATA
Type of construction Operation Materials Type of mounting Stroke Bore Ports Assembly position Operating temperature Special designs
1.45
Dimensions are in millimeters, inch notations are approximate for bore sizes.
with tie–rods double–acting, single–acting, other parts see coding aluminum end–blocks, other parts see coding with tie–rods, front flange, rear flange, feet front and rear trunnion, swivel combination 10 – 2500mm ø 32, 40, 50, 63, 80, 100, 125 32 = 1/8, 40/50 = 1/4, 63/80 = 3/8, 100/125 = 1/2 any position 0 – 80°C (with dry air –20°C), 32°F – 175°F (dry air – 4°F) for applications in damp, dusty or aggressive environments
The company reserves the right to vary models and dimensions without notice. These products are designed for industrial applications and are not suitable for sale to the general public.
S E R I E S
Catalog 2006
61
1 PNEUMATIC SPECIFICATIONS 1 – 10 bar [Min.1 bar (14.5psi); Max. 10 bar (145 psi)] 10 – 1000 mm/sec (No load) [Min. 10 mm/sec(No load); Max ≤ 1000mm/sec (No load)] clean air, lubrication*
*if lubricated air is used, it is recommended to use oil ISOVG32. Once applied the lubrication should never be interrupted. CYLINDER CODING
61M2P050A0200
SERIES 61 = ø f r o m 32 – 125 DIN/ISO 6431
VERSIONS M = standard, magnetic
BORE 032 mm 040 mm 050 mm 063 mm
OPERATION 1 = single–acting (front spring) 2 = double–acting (front and rear cushions) 3 = double–acting (no cushion) 4 = double–acting (rear cushions) 5 = double–acting (font cushion) 6 = double–acting (double–rod with front and rear cushions) 7 = single acting (double–rod)
S V N R W
STROKE (see table)
080 mm 100 mm 125 mm
= = = = =
special to be indicated viton rod seal tandem Buna–N rod seal all seals in viton
TYPE OF BRACKET A = standard lock nut for rod RL = cylinder with rod lock
C Y L I N D E R S
Operating pressure Speed Fluid
MATERIALS P = rolled stainless steel rod anodized profile aluminum tube Buna–N seals – rod seals polyurethane nuts and tie–rods zinc–plated steel R = rolled stainless steel rod anodized profile aluminum tube Buna–N seals – rod seals polyurethane nuts and tie–rods stainless steel steel
61M2P = standard version in stock. NOTE: Accessories are not mounted on the cylinders.
CHARACTERISTICS OF SINGLE–ACTING CYLINDERS SERIES 60–61 Force in N x 0.2245 = lbf ømm 32 40 50 63 80 100
min–max stroke 10 10 10 10 10 10
– – – – – –
75 75 75 75 75 75
Extend N at 6 bar 425 664 1037 1650 2660 4154
Force of spring at rest N (stroke 75 mm) 31 35 60 60 84 84
Force of compressed spring N 57 57 115 115 133 133
NOTE : the Series 60 – 61 single–acting cylinders’ dimensions for L1 and L2 are to be increased by 25 mm.
The company reserves the right to vary models and dimensions without notice. These products are designed for industrial applications and are not suitable for sale to the general public.
Dimensions are in millimeters, inch notations are approximate for bore sizes.
1.46
S E R I E S
61
Catalog 2006
1
C Y L I N D E R S
TABLE SHOWING AIR CONSUMPTION OF SERIES 61
ø Cyl. in mm (inch)
ø Rod in mm
32 (1 1/4”)
12
40 (1 9/16”)
16
50 (2”)
20
63 (2 1/2”)
20
80 (3 1/8”)
25
100 (4”)
25
125 (5”)
32
Working area in cm 2. Extend side Retract side Extend side Retract side Extend side Retract side Extend side Retract side Extend side Retract side Extend side Retract side Extend side Retract side
8.03 6.9 12.56 10.56 19.6 16.48 31.15 28 50.25 45.35 78.5 73.6 122.65 115.6
1
2
0.016 0.014 0.025 0.021 0.039 0.033 0.062 0.056 0.101 0.091 0.157 0.147 0.245 0.229
0.024 0.021 0.038 0.032 0.059 0.050 0.094 0.084 0.151 0.136 0.235 0.221 0.368 0.344
THE VALUES SHOWN IN THE TABLE WERE OBTAINED USING THE FOLLOWING FORMULA: Qs = consumption on extend side D = diameter on extend side in cm.
Qt = consumption on retract side d = diameter of rod in cm
Qs =
Operating pressure in bar 1 bar = 14.5 psi 3 4 5 6 7 8 Air consumption in NL for each 10 mm of stroke 0.032 0.040 0.048 0.056 0.064 0.072 0.028 0.035 0.042 0.048 0.055 0.062 0.050 0.063 0.075 0.088 0.100 0.113 0.042 0.053 0.063 0.074 0.085 0.095 0.079 0.098 0.118 0.137 0.157 0.177 0.066 0.083 0.099 0.115 0.132 0.148 0.125 0.156 0.187 0.218 0.249 0.280 0.112 0.140 0.168 0.196 0.224 0.252 0.201 0.251 0.302 0.352 0.402 0.452 0.181 0.227 0.272 0.317 0.363 0.408 0.314 0.392 0.471 0.550 0.628 0.707 0.295 0.368 0.441 0.515 0.589 0.663 0.491 0.614 0.736 0.859 0.982 1.104 0.459 0.573 0.688 0.803 0.917 1.032
D 2 . π . (P + 1) 4 . 1000
Qn = consumption of cylinder H = cylinder stroke in cm
.H
Qn = (Qs+Qt) · n
Qt =
9
10
0.080 0.069 0.126 0.106 0.196 0.165 0.312 0.280 0.503 0.454 0.785 0.736 1.227 1.147
0.088 0.076 0.138 0.116 0.216 0.182 0.343 0.308 0.553 0.499 0.864 0.810 1.350 1.261
(D 2 – d 2) . π . (P + 1) 4 . 1000
.H
n = number of cycles per minute P = operating pressure in bar
TABLE SHOWING THE OUTPUT FORCE OF SERIES 61
ø Cyl. in mm (inch)
ø Rod in mm
32 (1 1/4”)
12
40 (1 9/16”)
16
50 (2”)
20
63 (2 1/2”)
20
80 (3 1/8”)
25
100 (4”)
25
125 (5”)
32
Working area in cm 2. Extend side Retract side Extend side Retract side Extend side Retract side Extend side Retract side Extend side Retract side Extend side Retract side Extend side Retract side
8.03 6.9 12.56 10.56 19.6 16.48 31.15 28 50.25 45.35 78.5 73.6 122.65 115.6
1
2
70 60 110 93 173 145 275 247 443 400 692 650 1090 1019
140 120 220 186 346 290 550 494 886 800 1385 1300 2180 2037
THE VALUES SHOWN IN THE TABLE WERE OBTAINED USING THE FOLLOWING FORMULA: Ss = output force on extend side St = output force on retract side
1.47
P = operating pressure in bar D = diameter on extend side in cm
Dimensions are in millimeters, inch notations are approximate for bore sizes.
Operating pressure in bar 1 bar = 14.5 psi 3 4 5 6 7 8 Output force in N (efficiency factor 0,9) Force in N x 0.2245 lbf 210 283 354 425 494 595 180 243 305 365 426 487 330 443 554 664 775 886 280 375 465 559 652 745 518 692 865 1037 1210 1382 436 582 727 872 1017 1163 824 1098 1373 1650 1923 2198 740 988 1235 1480 1729 1976 1330 1772 2216 2660 3100 3545 1200 1600 2000 2400 2800 3200 2077 2770 3460 4154 4847 5540 1948 2608 3245 3895 4544 5193 3270 4360 5450 6540 7631 8721 3056 4075 5093 6112 7130 8149
Ss =
D2 . π 4
.P.η
St =
(D 2 – d 2) . π 4
9
10
635 548 998 838 1556 1308 2472 2222 3990 3600 6320 5842 9811 9168
706 608 1108 931 1729 1454 2747 2470 4432 4000 6923 6492 10901 10186
.P.η
d = diameter of rod in cm η = efficiency factor
The company reserves the right to vary models and dimensions without notice. These products are designed for industrial applications and are not suitable for sale to the general public.
S E R I E S
Catalog 2006
61
1 Cylinders Series 61
DIMENSIONS ø
MM
KK
Bd
32 40 50 63 80 100 125
12 16 20 20 25 25 32
M10x1,25 M12x1,25 M16x1,5 M16x1,5 M20x1,5 M20x1,5 M27x2
30 35 40 45 45 55 60
11
PL
L1
AM
VA
EE
WH
L2
ZJ
VD
14 15 15 21 21 23 23,5
18 21 25 26 30 35 42
22 24 32 32 40 40 54
4 4 4 4 4 4 6
G1/8 G1/4 G1/4 G3/8 G3/8 G1/2 G1/2
26 30 37 37 46 51 65
94 105 106 121 128 138 160
120 135 143 158 174 189 225
5 5 6 6 7 7 8
N
BG
RT
G
26 16 M6 5 29 16 M6 5 29,5 16 M8 8 36,5 16 M8 8 36 19 M10 8 38,5 19,5 M10 8 43 23 M12 10,5
SW1
SW2
32,5 13 46 10 38 13,5 55 13 46,5 16 64,5 17 56,5 28 75 17 72 30 93 22 89 40 110 22 110 50 135 27
6 6 8 8 10 10 12
TG
R
E
SW3 Cushion stroke 2 19 2 22 3 22 3 22 5 25 5 25 4 43
0 0 0 0 0 0 0
C Y L I N D E R S
+ add the stroke
N.B. : the single-acting cylinders’ sizes L1 nd L2 are increased by 25 mm.
Cylinders Series 61 Double-rod
+ add the stroke ++ add the stroke two times
DIMENSIONS ø
MM
KK
32 40 50 63 80 100 125
12 M10x1,25 16 M12x1,25 20 M16x1,5 20 M16x1,5 25 M20x1,5 25 M20x1,5 32 M27x2
Bd
11
30 35 40 45 45 55 60
PL
L1
AM
EE
WH
L2
ZM
VD
N
14 15 15 21 21 23 23,5
18 21 25 26 30 35 42
22 24 32 32 40 40 54
G1/8 G1/4 G1/4 G3/8 G3/8 G1/2 G1/2
26 30 37 37 46 51 65
94 105 106 121 128 138 160
146 165 180 195 220 240 290
5 5 6 6 7 7 8
26 29 29,5 36,5 36 38,5 43
RT
BG
G
M6 16 5 M6 16 5 M8 16 8 M8 16 8 M10 19 8 M10 19,5 8 M12 23 10,5
TG
R
E
32,5 13 46 38 13,5 55 46,5 16 64,5 56,5 28 75 72 30 93 89 40 110 110 50 135
SW1 SW2 SW3 Cushion stroke 10 6 2 19 13 6 2 22 17 8 3 22 17 8 3 22 22 10 5 25 22 10 5 25 27 12 4 43
N.B. : the single-acting cylinders’ sizes L1 nd L2 are increased by 25 mm. The company reserves the right to vary models and dimensions without notice. These products are designed for industrial applications and are not suitable for sale to the general public.
Dimensions are in millimeters, inch notations are approximate for bore sizes.
1.48
S E R I E S
61
Catalog 2006
1
C Y L I N D E R S
Cylinders Series 61 tandem
DIMENSIONS ø 32 40 50 63 80 100 125
EE
L2
L3
G1/8 G1/4 G1/4 G3/8 G3/8 G1/2 G1/2
171,5 191,5 188 204 225,5 231 264
197,5 221,5 225 230 271,5 282 329
Cylinders Series 61 with rod lock
DIMENSIONS
1.49
ø
L1
L2
L3
L4
L5
L6
L7
L8
L9
L10
ØD
øD1 d11 øD2
32 40 50 63 80 100 125
58 65 82 82 110 115 167
48 55 70 70 90 100 122
10 10 12 12 20 15 45
8 8 15 15 18 1 22
13 13 16 16 20 20 30
20,5 22,5 29,5 29,5 35 39 51
34 38 48 49,5 61 69 86,5
45 50 60 70 90 105 140
94 105 106 121 128 138 160
160 178 200 215 254 269 350
12 16 20 20 25 25 32
30,5 35 40 45 45 55 60
Dimensions are in millimeters, inch notations are approximate for bore sizes.
35 40 50 60 80 100 130
øD3 f8 A ±0.15 25 28 35 38 48 58 65
32,5 38 46,5 56,5 72 89 110
G
H
H1
M
Z
M5 G1/8 G1/8 G1/8 G1/8 G1/8 G1/8
25,5 30 36 40 50 58 80
46,5 53 64 75 95 110,5 150
M6 M6 M8 M8 M10 M10 M12
M6x20 M6x20 M6x20 M8x30 M10x35 M10x35 M12x40
The company reserves the right to vary models and dimensions without notice. These products are designed for industrial applications and are not suitable for sale to the general public.
S E R I E S
Catalog 2006
61
1 Foot mount Mod. B...
C Y L I N D E R S
Material: zinc-plated steel. The following is supplied: N° 2 feet N° 4 screws
+ add the stroke
DIMENSIONS Mod. B-41-32 B-41-40 B-41-50 B-41-63 B-41-80 B-41-100 B-41-125
ø
AT
SA ±1.25
XA ±1.25
TR JS 14
E
AB
AH JS 16
AO
AU
32 40 50 63 80 100 125
4 4 4 5 6 6 7
142 161 170 185 210 220 250
144 163 175 190 216 230 270
32 36 45 50 63 75 90
45 53,5 62,5 73 92 108,5 132
7 10 10 10 12 14,5 16,5
32 36 45 50 63 71 90
11 15 15 15 20 25 25
24 28 32 32 41 41 45
Torque force (max.) 6 Nm 6 Nm 13 Nm 13 Nm 19 Nm 22 Nm 26 Nm
Front and rear flange Mod. D-E... Material: aluminium. The following is supplied: N° 1 flange N° 4 screws
+ add the stroke
DIMENSIONS Mod. D-E-41-32 D-E-41-40 D-E-41-50 D-E-41-63 D-E-41-80 D-E-41-100 D-E-41-125
ø
W ±2
MF
ZB JS 14
TF JS 14
R JS 14
UF
E
FB H 13
ZF ±1.25
32 40 50 63 80 100 125
16 20 25 25 30 35 45
10 10 12 12 16 16 20
120 135 143 158 174 189 225
64 72 90 100 126 150 180
32 36 45 50 63 75 90
86 88 110 116 148 176 224
45 52 63 73 95 115 135
7 9 9 9 12 14 16
130 145 155 170 190 205 245
The company reserves the right to vary models and dimensions without notice. These products are designed for industrial applications and are not suitable for sale to the general public.
Torque force (max.) 6 Nm 6 Nm 13 Nm 13 Nm 19 Nm 22 Nm 26 Nm
Dimensions are in millimeters, inch notations are approximate for bore sizes.
1.50
S E R I E S
61
Catalog 2006
1
C Y L I N D E R S
Rear trunnion, female Mod. C... and CH... Material: aluminium. The following is supplied: N° 1 female trunnion N° 4 screws
+ add the stroke
DIMENSIONS Mod. C-41-32 C-41-40 C-41-50 C-41-63 C-H-41-80 C-H-41-100 C-H-41-125
ø
CD H 9
L
FL
XD ±1,6
MR
E
CB H 14
UB h 14
Torque force (max.)
32 40 50 63 80 100 125
10 12 12 16 16 20 25
12 15 15 20 24 29 30
22 25 27 32 36 41 50
142 160 170 190 210 230 275
10 13 13 15 15 18 25
45 52 63 73 95 115 135
26 28 32 40 50 60 70
45 52 60 70 90 110 130
6Nm 6Nm 13Nm 13Nm 19Nm 26Nm 26Nm
G 45 52 63 73 95 115 135
CB H14 26 28 32 40 50 60 70
UB h14 45 52 60 70 90 110 130
Front trunnion, female Mod. H... and C-H... Material: aluminium. The following is supplied: N° 1 female trunnion N° 4 screws
DIMENSIONS Mod. H-41-32 H-41-40 H-41-50 H-60-63 C-H-41-80 C-H-41-100 C-H-41-125
1.51
ø 32 40 50 63 80 100 125
CD H 9 10 12 12 16 16 20 25
E 16 20 25 25 34 39 45
H 4 5 10 5 10 10 15
D 120 135 143 158 174 189 225
MR 10 13 13 15 15 18 25
F 32,5 38 46,5 56,5 72 89 110
Dimensions are in millimeters, inch notations are approximate for bore sizes.
The company reserves the right to vary models and dimensions without notice. These products are designed for industrial applications and are not suitable for sale to the general public.
S E R I E S
Catalog 2006
61
1 Rear trunnion, male Mod. L...
C Y L I N D E R S
Material: aluminium. The following is supplied: N° 1 male trunnion N° 4 screws
+ add the stroke
DIMENSIONS ø
CD H 9
L
FL
XD ±1,6
MR
E
32 40 50 63 80 100 125
10 12 12 16 16 20 25
12 15 15 20 24 29 30
22 25 27 32 36 41 50
142 160 170 190 210 230 275
9 13 13 15 15 18 25
45 52 63 73 95 115 135
Mod. L-41-32 L-41-40 L-41-50 L-41-63 L-41-80 L-41-100 L-41-125
EW -0.2 -0.6 Torque force (max.) 26 6Nm 28 6Nm 32 13Nm 40 13Nm 50 19Nm 60 26Nm 70 26Nm
Centre trunnion Mod. F... Material: zinc-plated brass. The following is supplied: N° 1 centre trunnion N° 4 screws N° 4 fixing elements
+ add the stroke
DIMENSIONS Mod. F-61-32 F-61-40 F-61-50 F-61-63 F-61-80 F-61-100 F-61-125
ø
XV ±2
XV1±2
XV2±2
TM h14
TK
TD e9
TL h14
UW
R
32 40 50 63 80 100 125
62 69 76,5 86 94,5 104,5 123
73 82,5 90 97,5 110 120 145
84 96 103,5 109 125,5 135,5 167
50 63 75 90 110 132 160
20 20 20 25 25 30 30
12 16 16 20 20 25 25
12 16 16 20 20 25 25
70 78 91 94 130 145 155
0,1 0,15 0,15 0,15 0,15 0,2 0,2
The company reserves the right to vary models and dimensions without notice. These products are designed for industrial applications and are not suitable for sale to the general public.
Dimensions are in millimeters, inch notations are approximate for bore sizes.
1.52
S E R I E S
61
Catalog 2006
1 Accessory combination Mod. C+L+S
C Y L I N D E R S
Material: aluminium.
+ add the stroke
DIMENSIONS ø
CD H 9
L
FL
XD ±1,6
TG
E
I
M
32 40 50 63 80 100 125
10 12 12 16 16 20 25
12 15 15 20 24 29 30
22 25 27 32 36 41 50
142 160 170 190 210 230 275
32,5 38 46,5 56,5 72 89 110
45 52 63 73 95 115 135
10 10 12 12 12 12 20
22 25 27 32 36 41 50
TE J S 1 4 38 41 50 52 66 76 94
UL M A X 51 54 65 67 86 96 124
N Torque force (max.) 6,5 6Nm 6,5 6Nm 9 13Nm 9 13Nm 11 19Nm 11 22Nm 13 26Nm
90° male trunnion Mod. ZC... Material: aluminium. The following is supplied : N° 1 support
+ add the stroke
DIMENSIONS Mod. ZC-32 ZC-40 ZC-50 ZC-63 ZC-80 ZC-100 ZC-125
1.53
ø EB H 13 32 11 40 11 50 15 63 15 80 18 100 18 125 20
CK H 9 HB H 13 XD 10 6,6 154 12 6,6 173 12 9 188 16 9 209,5 16 11 237 20 11 260 25 14 315
Dimensions are in millimeters, inch notations are approximate for bore sizes.
EA M A X 10 15 16 16 20 20 30
GL J S 1 4 21 24 33 37 47 55 70
L5 M A X 1,6 1,6 1,6 1,6 2,5 2,5 3,2
RA J S 1 4 18 22 30 35 40 50 60
EM 26 28 32 40 50 60 70
- 0,2 - 0,6
-0,5 -1,5
UR J S 1 4 PH J S 1 5 31 32 35 36 45 45 50 50 60 63 70 71 90 90
BT BR M A X 8 10 10 11 12 13 12 15 14 15 15 19 20 22,5
P P P P P P P
The company reserves the right to vary models and dimensions without notice. These products are designed for industrial applications and are not suitable for sale to the general public.
S E R I E S
Catalog 2006
61
1 Trunnion ball - joint Mod. R*...
C Y L I N D E R S
Material: aluminium. *not according to standard. The following is supplied: N° 1 trunnion ball joint N° 4 screws
+ add the stroke
DIMENSIONS Mod. R-41-32 R-41-40 R-41-50 R-41-63 R-41-80 R-41-100
ø
CX
L
DL
XN ±1,6
MS
E
EX -0.1
Z°
32 40 50 63 80 100
10 12 12 16 16 20
12 15 15 20 24 29
22 25 27 32 36 41
142 160 170 190 210 230
16 20 20 24 24 30
45 52 63 73 95 115
14 16 16 21 21 25
4 4 4 4 4 4
Torque force (max.) 6Nm 6Nm 13Nm 13Nm 19Nm 22Nm
Counter bracket for centre trunnion Mod. BF... Material: aluminium. The following is supplied: N° 2 supports
DIMENSIONS Mod. BF-32 BF-40-50 BF-63-80 BF-100-125
ø 32 40-50 63-80 100-125
CR 12 16 20 25
NH C b3 15 7,5 3 18 9 3 20 10 3 25 12,5 3,5
TH 32 36 42 50
UL 46 55 65 75
The company reserves the right to vary models and dimensions without notice. These products are designed for industrial applications and are not suitable for sale to the general public.
FK 15 18 20 25
FN 30 36 40 50
B1 6,8 9 11 13
B2 11 15 18 20
HB 6,6 9 11 14
Dimensions are in millimeters, inch notations are approximate for bore sizes.
1.54
S E R I E S
61
Catalog 2006
1
C Y L I N D E R S
Assembly The horizontal mounting foot allows the connection between the valve or the solenoid valve and the cylinder, forming a compact pneumatic working unit, which is easy to apply.
Mod. PCV-61-K3 PCV-61-K4 PCV-61-KE PCV-61-K8
to to to to
connect connect connect connect
valves-solenoid valves-solenoid valves-solenoid valves-solenoid
valves valves valves valves
Series Series Series Series
3 4 port G1/4 E 4 port G1/8
Rod Fork End Mod. G... ISO 8140. Material: zinc-plated steel.
DIMENSIONS Mod. G-25-32 G-40 G-50-63 G-80-100 G-41-125
ø 32 40 50-63 80-100 125
øCK 10 12 16 20 30
LE 20 24 32 40 55
CM 10 12 16 20 30
CL 20 24 32 40 55
ER 12 14 19 25 28
CE KK 40 M10 x1,25 48 M12 x1,25 64 M16 x1,5 80 M20 x1,5 110 M27 x 2
ø CN H7 U 10 10,5 12 12 16 15 20 18 30 25
EN 14 16 21 25 37
ER 14 16 21 25 35
AX 20 22 28 33 51
B 26 32 40 48 74
øB1 18 20 26 34 48
Swivel Ball Joint Mod. GA... ISO 8139. Material: zinc-plated steel.
DIMENSIONS Mod GA-32 GA-40 GA-50-63 GA-80-100 GA-41-125
1.55
ø 32 40 50-63 80-100 125
Dimensions are in millimeters, inch notations are approximate for bore sizes.
CE KK øT 43 M10 x1,25 15 50 M12 x1,25 17,5 64 M16 x1,5 22 77 M20 x1,5 27,5 110 M27 x 2 40
Z 6,5 6,5 7,5 7 7,5
SW 17 19 22 30 41 The company reserves the right to vary models and dimensions without notice. These products are designed for industrial applications and are not suitable for sale to the general public.
S E R I E S
Catalog 2006
61
1 Piston Rod Socket Joint Mod. GY... Material: zama and zinc-plated steel.
C Y L I N D E R S
DIMENSIONS Mod. GY-25-32 GY-40 GY-50-63 GY-80-100
ø KK 32 M10 x 1,25 40 M12 x 1,25 50 - 63 M16 x 1,5 80 - 100 M20 x 1,5
L 74 84 112 133
CE 35 40 50 63
L2 6,5 6,5 8 10
AX 18 20 27 38
SW SW1 L1 17 11 19,5 19 17 22 22 19 27,5 30 24 31,5
L3 15 17 23 25
øT 15 17,5 22 27,5
øD 19 22 27 34
E 10 12 16 20
øB 14 19 22 29
øC 28 32 40 45
Z 15 15 11 7,5
Clevis Pin Mod. S...
Piston Rod Lock Nut Mod. U...
The following is supplied: N° 1 clevis pin (stainless steel 303) N° 2 Seeger (steel)
UNI EN ISO 4035. Material: zinc-plated steel. Included on all Series 61 cylinders.
DIMENSIONS Mod. S-32 S-40 S-50 S-63 S-80 S-100 S-125
ø 32 40 50 63 80 100 125
d 10 12 12 16 16 20 25
L 52 59 67 77 97 121 140,5
L1 46 53 6 71 91 111 132
L2 H13 1,1 1,1 1,1 1,1 1,1 1,3 1,3
L3 3 3 3 3 3 5 4,25
The company reserves the right to vary models and dimensions without notice. These products are designed for industrial applications and are not suitable for sale to the general public.
DIMENSIONS Mod. U-25-32 U-40 U-50-63 U-80-100 U-41-125
ø 32 40 50-63 80-100 125
D M10x1,25 M12x1,25 M16x1,5 M20x1,5 M27x2
m 6 7 8 9 12
SW 17 19 24 30 41
Dimensions are in millimeters, inch notations are approximate for bore sizes.
1.56