PPP

Page 1

ENCRIPTACION CON PPP

ROUTER MEX

ROUTER EUA

--- System Configuration Dialog ---

--- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: N

Continue with configuration dialog? [yes/no]: n

Press RETURN to get started!

Press RETURN to get started! Router>ENA Router#conf t Enter configuration commands, one per line. End with CNTL/Z. Router(config)#hostname MEX

Router>ena Router#conf t Enter configuration commands, one per line. End with CNTL/Z. Router(config)#int s 0/0/0

MEX(config)#int s 0/1/0 MEX(config-if)#ip address 208.79.4.1 255.255.255.0 MEX(config-if)#no sh %LINK-5-CHANGED: Interface Serial0/1/0, changed state to down MEX(config-if)#clock rate 128000 MEX(config-if)#no sh MEX(config-if)# %LINK-5-CHANGED: Interface Serial0/1/0, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1/0, changed state to up MEX(config-if)#exit MEX(config)#exit %SYS-5-CONFIG_I: Configured from console by console MEX#sh controllers s 0/1/0 Interface Serial0/1/0 Hardware is PowerQUICC MPC860 DCE V.35, clock rate 128000 idb at 0x81081AC4, driver data structure at 0x81084AC0 SCC Registers: General [GSMR]=0x2:0x00000000, Protocol-specific [PSMR]=0x8 Events [SCCE]=0x0000, Mask [SCCM]=0x0000, Status [SCCS]=0x00 Transmit on Demand [TODR]=0x0, Data Sync [DSR]=0x7E7E Interrupt Registers: Config [CICR]=0x00367F80, Pending [CIPR]=0x0000C000 Mask [CIMR]=0x00200000, In-srv [CISR]=0x00000000 Command register [CR]=0x580 Port A [PADIR]=0x1030, [PAPAR]=0xFFFF [PAODR]=0x0010, [PADAT]=0xCBFF Port B [PBDIR]=0x09C0F, [PBPAR]=0x0800E

Router(config-if)#ip address 208.79.4.2 255.255.255.0 Router(config-if)#no sh %LINK-5-CHANGED: Interface Serial0/0/0, changed state to up Router(config-if)# %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to up Router(config-if)#exit Router(config)#hostname EUA EUA(config)#exit} ^ % Invalid input detected at '^' marker. EUA(config)#exit %SYS-5-CONFIG_I: Configured from console by console EUA#ping 208.79.4.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.79.4.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 31/31/32 ms EUA#

EUA(config)#int s 0/0/0 EUA(config-if)#encapsulation ? frame-relay Frame Relay networks hdlc Serial HDLC synchronous ppp Point-to-Point protocol EUA(config-if)#encapsulation ? frame-relay Frame Relay networks hdlc Serial HDLC synchronous ppp Point-to-Point protocol EUA(config-if)#encapsulation ppp EUA(config-if)# %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to up

[PBODR]=0x00000, [PBDAT]=0x3FFFD Port C [PCDIR]=0x00C, [PCPAR]=0x200 [PCSO]=0xC20, [PCDAT]=0xDF2, [PCINT]=0x00F Receive Ring rmd(68012830): status 9000 length 60C address 3B6DAC4 rmd(68012838): status B000 length 60C address 3B6D444 Transmit Ring tmd(680128B0): status 0 length 0 address 0 tmd(680128B8): status 0 length 0 address 0 tmd(680128C0): status 0 length 0 address 0 tmd(680128C8): status 0 length 0 address 0 tmd(680128D0): status 0 length 0 address 0 tmd(680128D8): status 0 length 0 address 0 tmd(680128E0): status 0 length 0 address 0 tmd(680128E8): status 0 length 0 address 0 tmd(680128F0): status 0 length 0 address 0 tmd(680128F8): status 0 length 0 address 0 tmd(68012900): status 0 length 0 address 0 tmd(68012908): status 0 length 0 address 0 tmd(68012910): status 0 length 0 address 0 tmd(68012918): status 0 length 0 address 0 tmd(68012920): status 0 length 0 address 0 tmd(68012928): status 2000 length 0 address 0 tx_limited=1(2)

EUA(config)#username MEX password redes EUA(config)# %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to up (se levanta automaticamente la coneccion pork estopy usando la utentificacion para los 2 disositivos)

SCC GENERAL PARAMETER RAM (at 0x68013C00) Rx BD Base [RBASE]=0x2830, Fn Code [RFCR]=0x18 Tx BD Base [TBASE]=0x28B0, Fn Code [TFCR]=0x18 Max Rx Buff Len [MRBLR]=1548 Rx State [RSTATE]=0x0, BD Ptr [RBPTR]=0x2830 Tx State [TSTATE]=0x4000, BD Ptr [TBPTR]=0x28B0 SCC HDLC PARAMETER RAM (at 0x68013C38) CRC Preset [C_PRES]=0xFFFF, Mask [C_MASK]=0xF0B8 Errors: CRC [CRCEC]=0, Aborts [ABTSC]=0, Discards [DISFC]=0 Nonmatch Addr Cntr [NMARC]=0 Retry Count [RETRC]=0 Max Frame Length [MFLR]=1608 Rx Int Threshold [RFTHR]=0, Frame Cnt [RFCNT]=0 User-defined Address 0000/0000/0000/0000 User-defined Address Mask 0x0000

buffer size 1524 PowerQUICC SCC specific errors: 0 input aborts on receiving flag sequence 0 throttles, 0 enables 0 overruns 0 transmitter underruns 0 transmitter CTS losts 0 aborted short frames MEX#sh in s 0/1/0 Serial0/1/0 is up, line protocol is up (connected) Hardware is HD64570 Internet address is 208.79.4.1/24 MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255,

rxload 1/255 Encapsulation HDLC, loopback not set, keepalive set (10 sec) Last input never, output never, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0 (size/max/drops); Total output drops: 0 Queueing strategy: weighted fair Output queue: 0/1000/64/0 (size/max total/threshold/drops) Conversations 0/0/256 (active/max active/max total) Reserved Conversations 0/0 (allocated/max allocated) Available Bandwidth 96 kilobits/sec 5 minute input rate 8 bits/sec, 0 packets/sec 5 minute output rate 8 bits/sec, 0 packets/sec 5 packets input, 640 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 5 packets output, 640 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 output buffer failures, 0 output buffers swapped out 0 carrier transitions DCD=up DSR=up DTR=up RTS=up CTS=up MEX# PING 208.79.4.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 208.79.4.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 31/31/32 ms MEX# MEX#conf t

Enter configuration commands, one per line. End with CNTL/Z. MEX(config)#int s 0/1/0 MEX(config-if)#encapsulatio? encapsulation MEX(config-if)#encapsulation? encapsulation MEX(config-if)#encapsulation? encapsulation MEX(config-if)#encapsulation ? frame-relay Frame Relay networks hdlc Serial HDLC synchronous ppp Point-to-Point protocol MEX(config-if)#encapsulation ppp %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1/0, changed state to down (NO FUNCIONA PORQ SE DEVE EMPLEAR EL MISMO PROTOCOLO EN LOS 2 EQUIPOS EN Q SE AHRA EL ENLACE DEVE SER EL MISMO PROTOCOLO DE CAPA 2) MEX(config-if)# CUANDO ACTIVAMOS EL PROTOCOLO EN EL OTROP DISPOSITIVO AUTOMATICAMENTE SE LEVANTA ACTIVA) MEX#CONF T Enter configuration commands, one per line. End with CNTL/Z. MEX(config)#username EUA password redes MEX(config)#int s 0/1/0 MEX(config-if)#ppp autthenticacion chap ^ % Invalid input detected at '^' marker. MEX(config-if)#ppp authenticacion chap ^ % Invalid input detected at '^' marker. MEX(config-if)#ppp authentication chap %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1/0,

changed state to down (se vuele a caer la conexion pork se necesita la autentificacion en lso dos dispositivos)

Turn static files into dynamic content formats.

Create a flipbook
Issuu converts static files into: digital portfolios, online yearbooks, online catalogs, digital photo albums and more. Sign up and create your flipbook.