Eutectic-9000-Series-Powders

Specifically Developed Powders for OEM and Repair Applications on Glass Mold Parts ®

Eutectic 9001, 9002, 9003

• Reduced overspray is chieved through careful control of the chemical composition and particle size distribution • Special “wetting agents” result in the good fluidity • Reduced Boron content improves machinability • Extremely versatile, suitable for the use on a wide range of glass mold base metals

DESCRIPTION:

FINISHING:

The 9000 Series of powders have been specifically developed for OEM and repair applications on Glass Mold parts. They are suitable for use with the UltraJet, Eutalloy B System or Colmonoy Fusewelder Torches.

CPM 9001: - Use conventional single point tooling - Less tool wear

Coatings of the CPM 9001 are generally used for OEM applications on cast iron and or aluminum bronze molds.

Coatings of the CPM 9002 & 9003 are used for both OEM abd repair applicaions on cast iron and or aluminum bronze molds. In the case of aluminum bronze molds, the use of Albro 850 Flux is reccommended.

CPM 9002: - use single point tooling or hand files - Good machinability CPM 9003: - Use single point tooling or hand files - Good machinability

HEALTH & SAFETY: TECHNICAL DATA: Powder Properties Composition: Alloys of Nickel, Silicon and Boron plus a special wetting/fluxing agent.

Particle Size: Nominal -140 Mesh + 37 Microns Hall Flow: 13-14 seconds Apparent Density: 4.6 - 4.8 g/cc Coating Properties Typical Macro Hardness: CPM 9001 - HRC 25 (+/- 2) CPM 9002 - HRC 15 (+/- 2) CPM 9003 - HRC 18 (+/- 2)

Observe normal spraying practices, respiratory protection and proper air flow pattern advised. For general spray practices, see AWS Publications AWS C2. 1-73, “Recommended Safe Practices for Thermal Spraying and AWS TSS-85, “Thermal Spraying, Practice, Theory and Application.” Thermal spraying is a completely safe process when performed in accordance with proper safety measures. Become familiar with local safety regulations before starting spray operations. DO NOT operate your spraying equipment or use the spray material supplied, before you have thoroughly read the equipment instruction manual. Refer to the Eutectic web site for Material Safety Data Sheet (MSDS) information.

DISREGARDING THESE INSTRUCTIONS MAY BE HAZARDOUS TO YOUR HEALTH

APPLICATIONS: CPM 9001: Preform Blanks (corners, seams, necks& matches), Finish Molds (corners, seams, bottom plates and neck matches), Finish Guide Rings. Bottom Plates, Baffle and Blow Heads.

CPM 9002: Finish Neck Rings, Preform Blanks (coners and seams), Finish Molds (corners and seams) CPM 9003: Blow Heads, Finish Molds (corners and seams)

YOUR RESOURCE FOR PROTECTION, REPAIR AND JOINING SOLUTIONS Eutectic Corporation N94 W14355 Garwin Mace Drive Menomonee Falls, WI 53051 USA P 800-558-8524 • F 262-255-5542 www.eutecticusa.com

Eutectic Canada 428, rue Aime Vincent Vaudreuil-Dorion, Quebec J7V 5V5 Phone: (800) 361-9439 Fax: (514) 695-8793 www.eutectic-na.com

Eutectic Mexico KM 36.5 Autopista Mexico-Quertaro 54730 Cautitlan-Izcalli Estado de Mexico, Mexico Phone: 011 (52) 55-5872-1111 e-mail: eutectic.mexico@eutectic.com.mx

Statement of Liability: Due to variations inherent in specific applications, the technical information contained herein, including any information as to suggested product applications or results, is presented without representation or warranty, expressed or implied. Without limitation, there are no warranties of merchantability or of fitness for a particular purpose. Each process and application must be fully evaluated by the user in all respects, including suitability, compliance with applicable law and non-infringement of the rights of others, and Eutectic Corporation and its affiliates shall have no liability in respect thereof.

CPM 11-16-09 © 2007, Eutectic Corporation, ® Reg. T.M., Printed in the U.S.A.