Working Drawings Sample by celine lui

HANDICAP ACCESSIBILITY DIAGRAMS - DOORS X

6" MAX.

CLEAR FLOOR SPACE AT LAVATORIES

66" MIN.

40" MAX.

34" MAX.

29" MIN.

Clear Floor Space

Protected Piping

48" MIN.

LAVATORY CLEARANCES

18" (24" pref'd)

60" min

30" MIN.

27" MIN.

Clear Floor Space

48" MIN.

17" MIN.

4. Accessible routes to be provided between facilities, providing a minimum of 36 inches in width along the accessible route, and a minimum of 32 inches in width at doorways.

Note: Y=48" minimum if door has both a closer and a latch.

Note: X=12" if door has both a closer and a latch.

Lav.

19" MAX.

Lav.

3. Controls and operating mechanisms shall be operable with one hand and shall not require tight grasping, pinching or twisting of the wrist.

CLEAR FLOOR SPACE AT WATER CLOSETS

24" min Push Side

PLUMBING NOTES 1. 2. 3. 4.

PLUMBING FIXTURE SCHEDULE

All plumbing and gas piping work shall be installed in strict accordance with the requirements of Article 16 and Reference Standard RS 16 of the 2014 NYC Building Code.

Plumbing fixtures shall be of type and manufacture approved for use in New York City, and shall bear BSA approval.

All gas-fired equipment to be A.G.A. or M.E.A. approved. Plumbing Contractor to examine proposed layout with regard to existing field conditions, and shall notify Architect of any discrepancies between assumed field conditions and those encountered during construction. Plumbing contractor shall inform Architect of any revisions to plan which shall be necessary, based on conditions uncovered in the field, in order to install all fixtures, equipment and piping in strict accordance with the requirements of the NYC Building and Plumbing codes.

Plumbing Contractor shall arrange and obtain inspections and required sign-offs.

Remove or relocate all plumbing as required. Removed pipes shall be cut to a point of concealment behind or below finish surfaces, and shall be properly capped or plugged.

All soil & vent piping shall be "no hub" cast iron.

All branch piping of 4" Ø or greater shall be pitched 1/8" per foot or less than 1/4" per foot. All vent piping shall be pitched to drain.

All hot and cold water piping shall be copper tubing type "L" with 95-5 soldered joints.

Above Finished Floor Access Panel Adjacent Air Conditioner Air Handling Unit Aluminum Architectural Block Bottom of Building Cabinet Ceiling Ceiling Height Centerline Ceramic Tile Closet Column Concrete Concrete Masonry Unit Continuous Control Joint Diameter Drinking Fountain Down Elevation Equal Existing Expansion Joint Exterior Fire Extinguisher Fire Extinguisher Cabinet

Reference A-500 for Plumbing Fixture tags. P.1

KOHLER WIDESPREAD BATHROOM SINK FAUCET (K-14406-4)

P.2

KOHLER WALL-MOUNTS BATHROOM SINK (K-2053)

P.3

KOHLER ONE-PIECE TOILET (K-3828)

P.4

FIAT MOP SINK (TSB-100)

P.5

AMERICAN STANDARD UTILITY FAUCET (8344.212)

PLUMBING RISER DIAGRAMS

Pull Side

24" min Pull Side

TO GO

101

WC (ADA)

103

BAR

1 - 1/2" 2"

1 - 1/2" W.C.

2" 3"

1 - 1/2" W.C.

LAV.

UNDERMOUNT SINK

C01

104

1 - 1/2"

LAV.

UNDERMOUNT SINK

CLEANOUT

WC (ADA)

1 - 1/2"

FIRST FLOOR

102

2" 3"

CLOSET

C03

1 - 1/2" NOTE: PLUMBING FIXTURES AT PREP AREA TO BE CONFIRMED BY KITCHEN CONSULTANT

1 - 1/2" W.C.

LAV.

MOP SINK

CELLAR TO SEWER AT SMITH STREET

CLEANOUT 2"

CLEANOUT

Scope of Work:

A new stair, new walls, new doors, new plumbing fixtures and fitting, new electrical work (including new lighting fixtures), a new finishes.

Location:

191 Smith Street, Brooklyn, NY 11231

Tax Block and Lot:

Block: 397, Lot: 07

Landmark:

Zoning District: Overlay(s):

R6B Residential C2-4

Zoning Map:

16c 30132806F

Note: X=36" minimum if Y=60" X=42" minimum if Y=54"

Note: Y=54" minimum if door has a closer.

HINGE SIDE APPROACHES - SWING DOORS

LATCH SIDE APPROACHES - SWING DOORS

Certificate of Occupancy:

Plastic Laminate Plywood Quantity Radius Required Reinforcing Right Hand Roof Drain Rough Opening Schedule Section Similar Square Foot Stainless Steel Steel Structural / Structure Suspended Telephone Top of Top of Catch Basin Top of Curb Typical Verify In Field Vertical Vinyl Composite Tile Utility Water Closet With Without Wood

INTERIORS

CELINE CAROL LUI DESIGN 36 BOND ST, BROOKLYN, NY 11230 CCL@GMAIL.COM 408 578 9091

DRAWING INDEX A.F.F. A.P. ADJ. A.C. A.H.U. ALUM. ARCH. BLK. B.O. BLDG. CAB. CLG. CLG. HT. C.L. C.T. CL. COL. CONC. C.M.U. CONT. C.J. DIA. D.F. DN ELEV. EQ. EX'G. E.J. EXT. F.E. F.E.C.

Finish Finish Floor Floor Floor Drain Fluorescent Foot / Feet Galvanized Gypsum Wall Board Hardware Height Hollow Metal Horizontal Insulation Laminated Lavatory Left Hand Masonry Opening Maximum Mechanical Metal Minimum Mounted Necessary Nominal Not in Contract Not to Scale On Center Opposite Painted Pair Perforated

FIN. FIN. FL. FL. F.D. FLUOR. FT. GALV. G.W.B. HDWR. HT. H.M. HORIZ. INSUL. LAM. LAV. L.H. M.O. MAX. MECH. MTL. MIN. MTD. NEC. NOM. N.I.C. N.T.S. O.C. OPP. PTD. PR. PERF.

P.LAM. PLYWD. QTY. RAD. REQ'D. REINF. R.H. R.D. R.O. SCHED. SECT. SIM. S.F. ST. STL. STL. STRUCT. SUSP. TEL. T.O. T.C.B. T.O.C. TYP. V.I.F. VERT. V.C.T. UTIL. W.C. W/ W/O WD.

PROJECT NOTES 1.

RENOVATION OF A CAFE/BAR IN AN EXISTING ONE-STORY BUILDING PROJECT DATA

ABBREVIATIONS

Plumbing Fixture models are provided to establish a quality of fixture and an operational standard. Equivalent manufacturers are acceptable upon review and approval of Interior Designer.

10. Minimum supply to each fixture shall be 1/2" Ø. All fixtures shall have a shut-off valve at all fixture groups at the risers; provide stops at each fixture.

KITCHEN

Push Side

Note: Y=48" minimum if door has a closer.

Pull Side

FRONT APPROACHES - SWING DOORS

Y 42" min

Push Side

18"

Mirror Lever Valve

Y 42" min

36" MIN. 18"

a. Fixtures to be provided with the required clear floor space.

2. Proposed bathrooms to comply with the applicable requirements of ICC A117.1-2009 for handicapped access, including:

191 SMITH STREET BROOKLYN, NY 11201

54" min

48" min

1. Proposed work to comply with applicable requirements of ICC A117.1-2009.

Y 48" min

HANDICAP ACCESSIBILITY DIAGRAMS AND NOTES - BATHROOMS

All work shall conform with the Contract and with the Project Manual included as part of these Construction Documents. Before commencing work, the Contractor shall file all required Certificates of Insurance with the Department of Buildings, obtain all required permits, and pay all fees required by governing New York City agencies. No work is to begin without proper permits. Examination of the site and portions thereof which will affect this work shall be made immediately by the Contractor, who shall compare existing conditions with the Drawings and satisfy him/herself as to the conditions under which work is to be performed. Contractor shall notify the Designer of any conditions requiring modification before proceeding with the work. Contractor shall at such time ascertain and check locations of existing structure. Contractor's bid shall be based upon this examination.

INTERIORS CONTINUED

T-100

PROJECT INFO & GENERAL NOTES

A-900 PARTITION SCHEDULE

A-050

REMOVALS FLOOR PLANS

A-910

A-100

CELLAR & FIRST FLOOR PLANS

DOOR SCHEDULE, DOOR TYPES, AND TYPICAL DETAILS

A-110

CELLAR & FIRST FLOOR POWER & SIGNAL PLANS

A-920

FINISH SCHEDULE

A-300 A-301

BUILDING SECTIONS BUILDING SECTIONS

A-500 A-501

INTERIOR BATHROOM PLANS INTERIOR ELEVATIONS

A-700 A-701

ENLARGED STAIR PLANS & SECTION ENLARGED STAIR SECTION

A-800 A-801

MILLWORK - SEATING MILLWORK - SEATING

PROJECT:

LEA

SYMBOL LEGEND 12. Contractor shall protect area and new or existing materials and finishes from damage which may occur from construction, demolition, dust, water, etc., and shall provide and maintain temporary barricades, closure walls, etc., as required to protect the public during the period of construction. Damage to new and existing materials, finishes, structures, and equipment shall be repaired or replaced to the satisfaction of the Client at no additional expense to the Client. 13. All work listed, shown, or implied on any Construction Document shall be supplied and installed by the Contractor, except where noted otherwise.

14. Contractor shall notify Designer immediately of all utilities determined in the course of construction as being necessary to be removed which have not otherwise been noted for removal in the Construction Documents. Contractor shall remove such utilities only after consultation with the Designer and Client. Whether predetermined in the Construction Documents 4. Contractor shall verify all dimensions, elevations and or determined in the field, disconnect, cut back to conditions at the site, confirm that the work is buildable as source, and cap all utility services removed. Seal all shown, and notify Designer in writing of any penetrations created by the removal of utilities to match discrepancies prior to proceeding with the work in adjacent construction and finishes. question. 15. All manufactured articles, materials, and equipment 5. All dimensions are to finish face of masonry, centerline of shall be installed, connected, erected, cleaned, and steel, face of finish or casework unless otherwise noted. conditioned per the manufacturer's instructions. In case Dimensions noted as "CLR" are not adjustable without of differences between manufacturer's instructions and Designer's review. Dimensions are not adjustable without the Contract Documents, the Contractor shall notify the Designer's approval unless noted as "+/-". Field Designer before proceeding with the work in question. determine dimensions marked "V.I.F." prior to commencement of construction, and notify any variances 16. All work noted "By Others" or "N.I.C." shall be provided to Designer for resolution. by the Client or under separate contract. Submit to the Designer and Client schedule requirements for this 6. "Align" shall mean to accurately locate finish faces in the "other" work in the construction progress schedule and same plane. coordinate as required to assure orderly sequence of installation. 7. The Contract Documents are complementary. What is shown or referred to on any shall be provided as though 17. The Contractor shall remove all rubbish and waste shown on all. materials of all Subcontractors and trades on a daily basis and shall exercise strict control over job cleaning 8. Do not scale drawings. Dimensions and notes shall to prevent any dirt, debris, or dust from affecting any govern. Drawings at a large scale shall take precedence finished areas in or outside the job site. Burning of over drawings of a small scale. Details shall govern over debris on site shall not be permitted. plans and elevations. 18. Upon completing the job, the Contractor shall leave the 9. Repetitive features not shown on Drawings shall be premises and all affected areas clean and in an orderly completely provided as if drawn in full. manner ready for move-in. This is to include cleaning of all glass (including inside of exterior glass) and frames, 10. Contractor to verify layout of partitions, doors, electrical both new and existing. outlets, data and telephone outlets, light fixtures, and switches with Designer prior to proceeding with 19. Plumbing and electrical work shall be performed by construction. Contractor to verify that no conflicts exist in persons licensed in their trades, who shall arrange for locations of any mechanical, telephone, data, electrical, and obtain inspections and required sign-offs. lighting and plumbing equipment (including all piping, ductwork and conduit) and that all required clearances for 20. The Contractor shall be responsible for the protection installation and maintenance are provided. of all conditions and materials within the proposed construction area. The Contractor shall design and 11. Visits to the site by the Designer are only intended to install adequate shoring and bracing for all structural or ensure compliance with the design intent and should not removal tasks. The Contractor shall have sole be construed as being related to site safety. responsibility for any damage or injuries caused by or during the execution of the work.

DOOR NUMBER

100

ROOM NAME

ROOM INFO

CONF. RM. 100

ROOM NUMBER

WINDOW NUMBER

WALL TYPE BUILDING ELEVATION

BUILDING SECTION

ELEVATION NUMBER

A-200

SHEET NUMBER

SECTION NUMBER

1 A-300

SHEET NOTE TAG ALIGN FINISHES

A-500

ELEVATION NUMBER SHEET NUMBER

RATED PARTITION

NEW GYP. BD. WALLS DRAWING:

SHEET NUMBER

INTERIOR ELEVATION D

REVISION

191 SMITH STREET BROOKLYN, NEW YORK 11201

EXISTING WALLS TO REMAIN

LEVEL CHANGE

NOT IN PROJECT SCOPE

PROJECT INFORMATION AND GENERAL NOTES

ALIGN

EXISTING SWING DOOR TO REMAIN ISSUE DATE :

DETAIL TAG

DETAIL NUMBER

A-800

SHEET NUMBER

COLUMN LINE

+ 8'-0"

CENTERLINE

DRAWN BY :

CELINE LUI

NORTH ARROW PROJECT NUMBER :

COLUMN NUMBER

NEW SWING DOOR

INTERMEDIATE LANDING

ELEVATION HEIGHT

03.12.2020

NEW SLIDING DOOR

DRAWING :

2000 SEAL :

VICINITY MAP

NO SCALE

DOB JOB NUMBER :

DOCUMENT :

SITE DRAWING NUMBER:

T-100.00 S SCAN STICKER:

GENERAL NOTES

NO ATTEMPT IS MADE TO MENTION EVERY ITEM OF REMOVAL OR ALTERNATION WORK REQUIRED. THE GENERAL CONTRACTOR SHALL PERFORM ALL WORK NECESSARY TO COMPLETE THE PROJECT IN FULL COMPLIANCE WITH THE INTENDED RESULTS AND DESIGN INTENT DESCRIBED BY THE DRAWINGS.

90'-541" 55'-441"

ALL SURFACES DESIGNATED TO REMAIN SHALL BE PROTECTED TO ASSURE THAT THEY ARE NOT DAMAGED IN REMOVALS PROCESS. ANY ITEMS THAT ARE DAMAGED SHALL BE REPAIRED AT NO ADDITIONAL COST TO THE CLIENT. AVOID UNNECESSARY CUTTING AND PATCHING.

DIMENSION INFORMATION IS SHOWN TO FACILITATE THE RENOVATION OF THESE SPACES. ALL REMOVALS WORK MUST BE COORDINATED WITH THE ARCHITECTURAL DRAWINGS. COORDINATE AND VERIFY SCOPE OF ELECTRICAL REMOVALS WITH THE DESIGNER AND ENGINEER PRIOR TO COMMENCEMENT WITH WORK

IF THE GENERAL CONTRACTOR DISCOVERS DISCREPANCIES, OMISSIONS, OR HIDDEN CONDITIONS DIFFERING FROM REMOVALS INFORMATION, GENERAL CONTRACTOR NOTIFY THE INTERIOR DESIGNER BEFORE PROCEEDING WITH WORK.

PRIOR TO COMMENCEMENT OF REMOVALS, GENERAL CONTRACTOR TO SCHEDULE ON-SITE MEETING WITH THE INTERIOR DESIGNER AND BUILDING MANAGEMENT TO REVIEW EXTENT OF REMOVALS WORK.

PROVIDE TEMPORARY DUST CONTROL BARRIERS BETWEEN AREAS OF WORK AND OCCUPIED AREAS. CAP VENTS AND TAKE MEASUREMENTS FOR DUST CONTROL.

ALL WORK TO BE DONE IN ACCORDANCE WITH OSHA STANDARDS

35'-1"

9'-334"

10'-434"

3'-4"

3 12

12'-103 8"

7'-034"

5 25'-0"

3" 20'-28

TYP.

CELINE CAROL LUI DESIGN 36 BOND ST, BROOKLYN, NY 11230 CCL@GMAIL.COM 408 578 9091

8'-721"

7 4

TYP.

1 4

10 SHEET NOTES

1 A-050

FIRST FLOOR REMOVALS PLAN

3/16" = 1'-0"

REMOVE EXISTING STAIR AND HANDRILS

REMOVE PORTION OF EXISTING FLOOR AND FLOOR FRAMING. SHORE AS REQUIRED.

REMOVE EXISTING EXTERIOR WALL; SHORE AS REQUIRED

REMOVE EXISTING INTERIOR NON-LOADBEARING PARTITION

REMOVE EXISTING DOOR AND FRAME

REMOVE EXISTING PLUMBING FIXTURES AND FINISHES

REMOVE EXISTING FINISH FLOORING AND SUB-FLOORING BELOW

REMOVE PORTION OF EXISTING COLUMNS

FACE OF EXISTING CELLAR WALL BELOW

EXCAVATE FOR FUTURE WATERPROOFING AND TRENCH DRAIN ALONG EXISTING FOUNDATION WALL

REMOVE EXISTING PAVERS AND SETTING MATERIAL

EXISTING DOOR TO REMAIN; SCOPES OF WORK TO BE DETERMINED

PROJECT:

LEA 191 SMITH STREET BROOKLYN, NEW YORK 11201 BLOCK: 397

90'-541" 55'-441"

BIN:3336059

CELLAR AND FIRST FLOOR REMOVALS FLOOR PLANS

35'-1"

ISSUE DATE :

03.12.2020

9'-334"

LOT: 07

DRAWING:

PROJECT NUMBER :

DRAWN BY :

CELINE LUI DRAWING :

2000

SEAL :

25'-0"

7'-034"

8 4

CRAWLSPACE (N.I.C.)

CONSTRUCTION LEGEND NOT IN PROJECT SCOPE

8'-721"

EXISTING PARTITION TO REMAIN

EXISTING SWING DOOR TO REMAIN

1 4

DOB JOB NUMBER :

NEW GYPSUM BOARD PARTITION

DRAWING NUMBER:

A-050.00

NEW SLIDING DOOR

NEW SWING DOOR S SCAN STICKER:

2 A-050

CELLAR REMOVALS PLAN

DOCUMENT :

RATED SEPARATION

FIRE ALARM PULL STATION FIRE ALARM HORN/STROBE

3/16" = 1'-0"

EXIT SIGN

F.A.

OCCUPANCY NOTES

1 A-300

CELLAR AREA: DOMINANT OCCUPANCY: OCCUPANT LOAD FACTOR: SECONDARY OCCUPANCY: OCCUPANT LOAD FACTOR: TOTAL OCCUPANTS:

D 1 A-800

100'-0"

24'-341"

31'-1"

SEATING 1

9'-634"

35'-1"

BAR

105

102

FIRST FLOOR AREA: DOMINANT OCCUPANCY: OCCUPANT LOAD FACTOR: TOTAL OCCUPANTS:

1,215G.S.F ASSEMBLY(A-2 KITCHEN) 100 NET ASSEMBLY(A-2 CAFE) 15 NET (UNCONCENTRATED) 30 1,215G.S.F ASSEMBLY(A-2 CAFE) 15 NET (UNCONCENTRATED) 30

SEATING 2 106

1 GENERAL NOTES 1 A-700

9'-134"

11 16

1. ALL GYPSUM BOARD PARTITIONS SHALL BE COVERED BY LATEX PRIMER AND THREE COATS OF ACRYLIC LATEX PAINT(SEMI-GLOSS); TYPICAL UNLESS OTHERWISE NOTED

2. ROUTING OF ALL EXPOSED CONDUIT, JUNCTION BOXES, ETC., IS TO BE COORDINATED TO ENSURE CLEAN INSTALLATION. THIS INCLUDES METHODS OF ATTACHMENT

2 1 A-301

6'-534"

25'-0"

100

ENTRY

100

TO GO

101

3 109

9'-421"

15 11

F F

103

104

15 11

SEATING 5 109

E D

4 SEATING 3 107

SEATING 4 108

STAIR

WC (ADA)

S1 1 A-500

1 A-100

DESIGN

SHEET NOTES

CELINE CAROL LUI

FIRST FLOOR PLAN

WC (ADA)

103

NEW STAIR WITH CONTINUOUS STEEL HANDRIL AND GUARDRAIL

NEW BUILT-IN MILLWORK AT GARDEN

NEW COUNTERTOP

EQUIPMENT AND FIXTURES AT PREP AREA TO BE CONFIRMED BY KITCHEN CONSULTANT

NEW GREEN WALL PARTITION

NEW BUILT-IN MILLWORK

NEW BUILT-IN BANQUETTE

NEW BUILT-IN TABLE

NEW FINISH FLOOR OVER NEW SUB-FLOOR SHEATHING

104

3/16" = 1'-0"

36 BOND ST, BROOKLYN, NY 11230

CCL@GMAIL.COM 408 578 9091

NEW BUILT-IN BAR COUNTERTOP

NEW TILE FLOORING

EXISTING DOOR; SCOPE OF WORK TO BE DETERMINED

REPLACE DOOR WITH NEW WINDOW

NEW BUILT-IN STONE AT RECEPTION

NEW PLUMBING FIXTURES

PROJECT:

LEA

1 A-300

2 A-700

2 A-500

191 SMITH STREET BROOKLYN, NEW YORK 11201

DRAWING:

90'-541" 24'-341"

31'-1"

SEATING 2 C02

CELLAR AND FIRST FLOOR CONSTRUCTION PLANS

35'-1"

CLOSET

SEATING 3 C03

C03 ISSUE DATE :

03.12.2020 C

9'-134"

E F

C01

PROJECT NUMBER :

6'-534"

25'-0"

C02

1 A-700

SEAL :

CRAWLSPACE (N.I.C.)

EXISTING PARTITION TO REMAIN

UP B

CONSTRUCTION LEGEND NOT IN PROJECT SCOPE

C04

DRAWING :

2000

2 C

CELINE LUI

C03

1 A-301

DRAWN BY :

9'-421"

6 C

EXISTING SWING DOOR TO REMAIN

F F

DOB JOB NUMBER :

NEW GYPSUM BOARD PARTITION

KITCHEN

C01

SEATING 4 C04

DRAWING NUMBER:

A-100.00

NEW SLIDING DOOR

C04

NEW SWING DOOR S SCAN STICKER:

2 A-100

CELLAR FLOOR PLAN

DOCUMENT :

RATED SEPARATION

FIRE ALARM PULL STATION FIRE ALARM HORN/STROBE

3/16" = 1'-0"

EXIT SIGN

F.A.

GENERAL NOTES

ROUTING OF ALL EXPOSED CONDUIT, JUNCTION BOXES,ETC. IS TO BE COORDINATED TO ENSURE CLEAN INSTALLATION, THIS INCLUDES METHODS OF ATTACHMENT.

90'-541" 24'-341"

31'-1"

SEATING 1

35'-1"

105

BAR

102

SEATING 2 106

9'-134"

CELINE CAROL LUI

DESIGN

6'-534"

25'-0"

SHEET NOTES ENTRY

100

TO GO

101

36 BOND ST, BROOKLYN, NY 11230

POWER AND SIGNAL REQUIREMENTS FOR PREP AREA TO BE CONFIRMED BY KITCHEN CONSULTANT.

CCL@GMAIL.COM 408 578 9091

9'-421"

4 SEATING 3 107

1 A-110

SEATING 4 108

STAIR

FIRST FLOOR POWER AND SIGNAL PLAN

WC (ADA)

103

WC (ADA)

104

3/16" = 1'-0"

PROJECT:

LEA

191 SMITH STREET BROOKLYN, NEW YORK 11201

DRAWING:

90'-541" 24'-341"

31'-1"

SEATING 2 C02

CELLAR AND FIRST FLOOR POWER AND SIGNAL PLANS

35'-1"

SEATING 3 C03

CLOSET

C05 ISSUE DATE :

9'-134"

03.12.2020 UP

PROJECT NUMBER :

CELINE LUI DRAWING :

2000 UP

6'-534"

25'-0"

DRAWN BY :

SEAL :

CRAWLSPACE (N.I.C.)

ELECTRICAL SYMBOL LEGEND WAP

WIRELESS ACCESS POINT (WAP) COMPUTER DATA OUTLET

TELEPHONE JACK

COMPUTER DATA OUTLET AT THE FINISH FLOOR TELEPHONE JACK AT THE FINISH FLOOR

9'-421"

SATELLITE TELEVISION OUTLET DIGITAL CABLE OUTLET

DOB JOB NUMBER :

DOCUMENT :

WALL MOUNTED DUPLEX RECEPTACLE OUTLET THERMOSTAT

WALL MOUNTED QUADRUPLEX RECEPTACLE OUTLET

DRAWING NUMBER:

RECESSED DUPLEX OUTLET AT THE FINISH FLOOR

KITCHEN

C01

SEATING 4 C04

C06

RECESSED DOUBLE DUPLEX OUTLET AT THE FINISH FLOOR RECESSED DUPLEX OUTLET AT THE CEILING

GFI K.P.

2 A-110

CELLAR POWER AND SIGNAL PLAN

3/16" = 1'-0"

A-110.00

GROUND FAULT INTERRUPTION SECURITY ALARM KEYPAD

S SCAN STICKER:

GENERAL NOTES

ALL GYPSUM BD. PARTITIONS SHALL BE COVERED BY LATEX PRIMER AND THREE (3) COATS OF ACRYLIC LATEX PAINT (SEMI-GLOSS); TYPICAL UNLESS OTHERWISE NOTED

ROUTING OF ALL EXPOSED CONDUIT, JUNCTION BOXES, ETC., IS TO BE COORDINATED TO ENSURE CLEAN INSTALLATION. THIS INCLUDES MEATHODS OF ATTACHMENT

1 A-701

2 A-800

ENTRY

100

TO GO

101

BAR

102

SEATING 1 105

SHEET NOTES

ROOF

+ 15'-3 1/4"

NEW STAIR WITH CONTINUOUS STEEL HANDRIL AND GUARDRAIL

NEW GREEN GARDEN MILLWORK

NEW SLIDING ALUMINUM AND GLASS DOORS AND INSECT SCREENS

EQUIPMENTS AND FIXTURES AT PREP AREA TO BE CONFIRMED BY KITCHEN CONSULTANT

NEW GREEN WALL PARTITION

CELINE CAROL LUI

NEW BUILT-IN MILLWORK

DESIGN

NEW BUILT-IN BANQUETTE

NEW BUILT-IN TABLE

NEW FINISH FLOOR OVER NEW SUB-FLOOR SHEATHING

15'-341"

Beer

leoville

HENKE

干红葡

萄酒

3 13

36 BOND ST, BROOKLYN, NY 11230 CCL@GMAIL.COM 408 578 9091

1ST FLR. FIN. FLR.

10'-821"

+ 0'-0"

CELLAR

-10'-8 1/2"

1 A-300

BUILDING SECTION (LOOKING NORTH)

3/16" = 1'-0"

PROJECT:

LEA

191 SMITH STREET BROOKLYN, NEW YORK 11201

DRAWING:

2 A-701

BUILDING SECTIONS

ISSUE DATE :

DRAWN BY :

CELINE LUI

ROOF

+ 15'-3 1/4" PROJECT NUMBER :

15'-341"

DRAWING :

SEAL :

Beer

leoville

HENKE

6 102

BAR

WC (ADA)

103

1ST FLR. FIN. FLR.

10'-821"

+ 0'-0"

DOB JOB NUMBER :

1 C03

CLOSET

DOCUMENT :

C04 DRAWING NUMBER:

A-300.00

CELLAR

-10'-8 1/2"

S SCAN STICKER:

2 A-300

BUILDING SECTION (LOOKING EAST)

3/16" = 1'-0"

5'-734"

8'-0"

CELINE CAROL LUI

8'-0"

DESIGN

3" 18

2'-11"

36 BOND ST, BROOKLYN, NY 11230

CCL@GMAIL.COM

1'-6"

408 578 9091 H.3

P.3

H.1

5'-0" DIA. CLR

J.2

8'-0"

CLR

8'-0" CLR

H.2

1 A-501

1'-6"

WC (ADA)

30" X 48" CLR

P.1 P.2

A E

2 A-501

P.1 P.2

103

WC (ADA)

104

PROJECT:

LEA 1 A-500

ENLARGED FLOOR PLAN - GENDER NEUTRAL ACCESSIBLE BATHROOMS

1/2" = 1'-0"

191 SMITH STREET BROOKLYN, NEW YORK 11201

DRAWING:

ENLARGED FLOOR PLANS BATHROOMS AND JAN. CLOSET P.4 P.5 ISSUE DATE :

A D

3 A-501

03.12.2020

DRAWN BY :

CELINE LUI

B PROJECT NUMBER :

DRAWING :

2000 SEAL :

CLOSET

2 A-500

C03

ENLARGED FLOOR PLAN - JANITORS CLOSET

DOB JOB NUMBER :

DOCUMENT :

1/2" = 1'-0"

01 DRAWING NUMBER:

A-500.00 S SCAN STICKER:

GYP. BD. WALL. PTD. (TYP.)

CELINE CAROL LUI

WALL MTD. HAND DRYER

DESIGN

WALL MTD. TOILET SEAT COVER DISPENSER

H1 H2

36 BOND ST, BROOKLYN, NY 11230 CCL@GMAIL.COM

408 578 9091

WALL MTD. LAVATORY CERAMIC TILE WALL BASE

A NORTH

1 A-501

B EAST

C SOUTH

GENDER NUETRAL ACCESSIBLE BATHROOMS 103 - INTERIOR ELEVATIONS CL

D WEST

1/2" = 1'-0"

3'-0" GRAB BAR

PROJECT:

LEA

3'-434"

INTERIOR ELEVATIONS

2'-5"

2'-915 16"

DRAWING:

1'-45 8"

1'-10"

3" 3'-716

3'-3"

5'-4"

6'-1115 16"

15" 6'-1116

191 SMITH STREET BROOKLYN, NEW YORK 11201

A NORTH

B EAST

C SOUTH

D WEST

ISSUE DATE :

03.12.2020

2 A-501

GENDER NUETRAL ACCESSIBLE BATHROOM 104 - INTERIOR ELEVATIONS

PROJECT NUMBER :

1/2" = 1'-0"

DRAWN BY :

CELINE LUI DRAWING :

2000 SEAL :

WOOD DOOR AND STL. FRAME. PTD.

GYP. BD. WALL. PTD. (TYP.)

WALL MOUNTED FAUCET

DOB JOB NUMBER :

4'-013 16"

DRAWING NUMBER:

3'-0"

CERAMIC TILE WALL BASE

A-501.00

FLR. MTD. MOP SINK

A NORTH

B EAST

C SOUTH

D WEST S SCAN STICKER:

3 A-501

JANITOR'S CLOSET- INTERIOR ELEVATIONS

DOCUMENT :

1/2" = 1'-0"

2 A-701

9'-078"

DIM. (LOWER STAIR RUN)

3'-0"

1'-11"

7 EQ. TREADS

LANDING

2'-915 16"

3'-8"

1'-0"

121"

CELINE CAROL LUI STAIR

DESIGN

S1 4'-3"

36 BOND ST, BROOKLYN, NY 11230

1 A-701

CCL@GMAIL.COM 408 578 9091

TO GO

3'-8"

3 101

DIM. (UPPER STAIR RUN)

3'-11" LANDING

1 A-700

8 EQ. TREADS

ENLARGED STAIR PLAN - FIRST FLOOR

1/2" = 1'-0"

2 A-701

9'-078"

PROJECT:

LEA

DIM. (LOWER STAIR RUN)

3'-0"

1'-11"

191 SMITH STREET BROOKLYN, NEW YORK 11201

7 EQ. TREADS

LANDING 1'-0"

S1 2'-915 16"

DRAWING:

3'-8"

STAIR

ENLARGED STAIR PLANS

2 ISSUE DATE :

DRAWN BY :

CELINE LUI DRAWING :

4'-3"

PROJECT NUMBER :

1 A-701

SEAL :

3'-8"

DOB JOB NUMBER :

SEATING 3 C03

DOCUMENT :

DRAWING NUMBER:

A-700.00 2 A-700

ENLARGED STAIR PLAN - CELLAR

S SCAN STICKER:

1/2" = 1'-0"

2 A-300

1 A-300

CELINE CAROL LUI DESIGN 36 BOND ST, BROOKLYN, NY 11230 CCL@GMAIL.COM 408 578 9091

SECOND FLOOR

14'-241"

+ 14'-2"

14'-241"

+ 14'-2"

PROJECT:

191 SMITH STREET BROOKLYN, NEW YORK 11201

3'-6"

7" 3'-216

7'-0"

LEA

DRAWING:

FIRST FLOOR

+ 0'-0"

ENLARGED STAIR SECTIONS

+ 0'-0"

03.12.2020

5'-1015 16"

ISSUE DATE :

CELINE LUI DRAWING :

2000

7 3'-216 "

3'-615 16"

1" 3'-116

9" 3'-416

PROJECT NUMBER :

DRAWN BY :

SEAL :

FIRST LANDING

3'-0"

9" 4'-916

- 5'-11"

9" 4'-916

- 5'-11"

DOB JOB NUMBER :

CELLAR

DOCUMENT :

CELLAR

- 10'-8"

- 10'-8" DRAWING NUMBER:

A-701.00 1 A-701

ENLARGED STAIR SECTION

2 1/2" = 1'-0"

A-702

ENLARGED STAIR SECTION

S SCAN STICKER:

1/2"

1 A-801

C 7" 18'-1116 7" 4'-716

FIXED SHELF

OAK SHELVING

STONE COUNTERTOP

9" 1'-616

2'-041"

1" 1'-516

ELEVATED STONE SERVICE DESK

CELINE CAROL LUI DESIGN 36 BOND ST, BROOKLYN, NY 11230 CCL@GMAIL.COM

OAK BAR SHELVING

408 578 9091

1'-415 16"

8'-881"

4 A-800

1'-421"

3 A-800

Beer

HENKE

1'-421"

WOODEN BAR COUNTER

leoville

11'

STONE COUNTERTOP

9" 1'-716

5" 78

1 A-800

ENLARGED BAR PLAN

3/4" = 1'-0" 881"

A-800

3'-881"

WOODEN BAR COUNTER

3 A-800

BAR ELEVATION (LOOKING WEST)

3/4" = 1'-0"

PROJECT:

LEA 191 SMITH STREET BROOKLYN, NEW YORK 11201

DRAWING:

MILLWORK- BAR

ISSUE DATE :

1'-415 16"

03.12.2020 PROJECT NUMBER :

Beer

leoville

DRAWN BY :

CELINE LUI DRAWING :

Beer

leoville

HENKE

2000

1'-421"

FIXED SHELF

1'-421"

SEAL :

葡萄

STONE COUNTERTOP

干红

葡萄

酒

9" 1'-716

11'

干红

5" 78

3 A-801

DOB JOB NUMBER :

3'-881"

RANGE

DOCUMENT :

881"

DRAWING NUMBER:

A-800.00 S SCAN STICKER:

2 A-800

BAR ELEVATION (LOOKING NORTH)

4 3/4" = 1'-0"

A-800

BAR ELEVATION (LOOKING NORTH)

3/4" = 1'-0"

LED STRIP LIGHT RECESSED INTO 15 DEGREE ANGLED GROOVE ALONG REAR OF SHELF TO FULL LENGTH OAK SHELF WITH STAINED FINISH CELINE CAROL LUI DESIGN 36 BOND ST, BROOKLYN, NY 11230 CCL@GMAIL.COM 408 578 9091

2 A-801

INVISIBLE BRACKET AND CONCEALED FASTENERS

RECESSED DOWNLIGHT (TYP.)

FIXED SHELF (TYP.) 2 A-801

SHELF DETAIL

ELEVATED SERVICE DESK BEYOND

3"=1'-0"

STONE COUNTERTOP PROJECT:

LEA 191 SMITH STREET BROOKLYN, NEW YORK 11201

STONE COUNTERTOP WOODBLOCKING

DRAWING:

STEEL PLATE

PLYWOOD

BRACKET

HOOK

ISSUE DATE :

03.12.2020 1 2"

THREADED ROD AND NUTS SECURED ON BOTH ENDS

3" 1'-916 8"

STONE FACING

MILLWORK BAR DETAILS

PROJECT NUMBER :

DRAWN BY :

CELINE LUI DRAWING :

2000 SEAL :

ADJUSTABLE SHELVING UNITS STONE COUNTERTOP

FOOT REST

DOB JOB NUMBER :

BOTTOM RACK

DOCUMENT :

01 DRAWING NUMBER:

1 A-801

BAR SECTION

1/2" = 1'-0"

3 A-801

COUNTER DETAIL

A-801.00 3"=1'-0"

S SCAN STICKER:

PARTITION TYPES

PARTITION NOTES

UNDERSIDE OF STRUCTURE

FIRE-RATED SEALANT

SLOTTED TOP TRACK (TYP.)

FINISHED CEILING-REFER TO REFLECTED CEILING PLANS

FINISHES CEILING REFER TO R.C.P.

CLG.

UNDERSIDE OF STRUCTURE

FINISHES CEILING REFER TO R.C.P.

TAPE AND COMPOUND EXPOSED JOINTS AT GYPSUM BOARD CEILING OR SOFFIT (TYP.)

FINISHES CEILING REFER TO R.C.P.

TAPE AND COMPOUND EXPOSED JOINTS AT GYPSUM BOARD CEILING OR SOFFIT (TYP.)

CLG.

GENERAL PARTITION NOTES: 1. Partition assemblies and associated fire resistance ratings are taken from RS-5-1B of the Gypsum Associations' "Fire Resistance Design Manual, 15th Edition." They were adopted under NYC Building Code Revision 262-86, dated 04/22/86.

CLG.

TAPE AND COMPOUND EXPOSED JOINTS AT GYPSUM BOARD CEILING OR SOFFIT (TYP.)

2. Drywall and masonry construction shall include continuous firestopping at all duct, fire-rated partitions.

pipe and conduit penetrations through

3. Seal the entire perimeter of fire-rated partitions airtight with fire rated sealant. 4. All fire-resistive partitions shall be constructed in compliance with testing requirements and manufacturer's recommendations for conditions as required. Construction of all systems will be equal to that tested assembly. 5. All non-load bearing material stud partitions are to extend to underside of structure, typical unless otherwise noted. 6. Provide moisture-resistant gypsum board of damp areas. 7. Provide Durock Cement Board at wet areas. 8. Tap and bed any corners and joints ready for finish.

INSULATION AS SCHEDULED

METAL STUD @ 16 O.C. MAX. (20 GAUGE MIN.)

TWO(2) LAYERS 58" TYPE X GYP. BD. BOTH SIDES

5 8"

CELINE CAROL LUI DESIGN 36 BOND ST, BROOKLYN, NY 11230 CCL@GMAIL.COM 408 578 9091

PLAN

TYPE X GYP. BD. BOTH SIDES

PLAN

MAXIMUM STUD SPACING = 16" ON CENTER ALLOWABLE DEFLECTION = L / 240

BASE AS SCHEDULED

CONTINUOUS METAL RUNNER

FIRE-RATED SEALANT

ACOUSTICAL SEALANT

TOP OF STRUCTURE

FASTENER

BASE

TYPE X GYP. BD. BOTH SIDES

FASTENER

BASE

2-HR RATED PARTITION

3" = 1'-0"

BASE

NON-LOADBEARING PARTITION 3" = 1'-0" 1-HR WHERE INDICATED

NON-LOAD-BEARING PARTITION

3" = 1'-0" PROJECT:

LEA

UNDERSIDE OF STRUCTURE

ACOUSTIC SEALANT

FINISHED CEILING-REFER TO REFLECTED CEILING PLANS

SLOTTED TOP TRACK (TYP.)

FINISHES CEILING REFER TO R.C.P.

FINISHES CEILING REFER TO R.C.P. 1"

TAPE AND COMPOUND EXPOSED JOINTS AT GYPSUM BOARD CEILING OR SOFFIT (TYP.)

FINISHED CEILING-REFER TO REFLECTED CEILING PLANS

TAPE AND COMPOUND EXPOSED JOINTS AT GYPSUM BOARD CEILING OR SOFFIT (TYP.)

CLG.

INSULATION AS SCHEDULED

STONE AS SCHEDULED

5 8"

TYPE X GYP. BD. BOTH SIDES

DRAWING:

PARTITION SCHEDULE

FINISHES CEILING REFER TO R.C.P.

PROVIDE MIN 1" OVERLAP AT TRANSITION TO 58" MOISTURE RESISTANT GYP. BD.

PLASTER SPOTS AS REQUIRED

CLG.

ACOUSTICAL SEALANT

SLOTTED TOP TRACK (TYP.) FINISHED CEILING-REFER TO REFLECTED CEILING PLANS

SLOTTED TOP TRACK (TYP.)

191 SMITH STREET BROOKLYN, NEW YORK 11201

TAPE AND COMPOUND EXPOSED JOINTS AT GYPSUM BOARD CEILING OR SOFFIT (TYP.)

ISSUE DATE :

03.12.2020 PROJECT NUMBER :

INSULATION AS SCHEDULED

TYPE X GYP. BD. BOTH SIDES

5 8"

DRAWN BY :

CELINE LUI DRAWING :

2000

TYPE X GYPSUM BOARD SEAL :

PLASTER SPOTS AS REQUIRED

PLAN

METAL STUD @ 16 O.C. MAX. (20 GAUGE MIN.)

WALL FINISH AS SCHEDULED

PLAN

ROOM SIDE

METAL STUD @ 16 O.C. MAX. (20 GAUGE MIN.)

ADDITIONAL LAYERS OF GYP. BD AS SCHEDULED

PLAN

ROOM SIDE

FACE OF EXISTING WALL OR STRUCTURE BASE AS SCHEDULED DOB JOB NUMBER :

CONTINUOUS METAL RUNNER

PLASTER SPOTS AS REQUIRED

PLASTER SPOTS AS REQUIRED TOP OF STRUCTURE

FASTENER

TOP OF STRUCTURE

FASTENER

BASE

A-900.00

FASTENER

BASE

01 DRAWING NUMBER:

ACOUSTICAL SEALANT TOP OF STRUCTURE

BASE S SCAN STICKER:

WET WALL PARTITION (STONE)

3" = 1'-0"

WET WALL PARTITION (TILE)

3" = 1'-0"

DOCUMENT :

CONTINUOUS METAL RUNNER

FURRED PARTITION

3" = 1'-0"

DOOR TYPES

DOOR SCHEDULE

FLOOR

DOOR NO.

CELLAR

DOOR LEAF & WINDOW

FRAME ROOM NAME

TYPE

C01

KITCHEN/ C01

V.I.F.

C02

KITCHEN/ C01

C03

CLOSET/ C03

C04

WC/ C04

MATERIAL

HARDWARE REMARKS

THICK. SIZE (W X H)

OPERATION

RATING

MATERIAL TYPE

SET

V.I.F.

SWING

V.I.F.

EXISTING DOOR

STL / TGL

1-3/4"

3'-0" x 7'-0"

SWING

STL

1-3/4"

3'-0" x 7'-0"

SWING

STL

1-3/4"

3'-0" x 7'-0"

SWING

STL

WINDOW

CELINE CAROL LUI DESIGN

36 BOND ST, BROOKLYN, NY 11230 CCL@GMAIL.COM

LEVER

408 578 9091

3'-2" TYP.

5'-0" TYP.

DOOR LEVER (TYP.)

TYPE A

TYPE B

FIRST FLOOR

100

ENTRY/ 100

V.I.F.

SWING

V.I.F.

EXISTING ENTRY DOOR (PAIR)

103

WC (ADA)/ 103

STL

1-3/4"

3'-0" x 7'-0"

SWING

STL

104

WC (ADA)/ 104

STL

1-3/4"

3'-0" x 7'-0"

SWING

STL

109

SEATING 5/109

ALUM/ TGL

1-3/8"

(2)3'-0" x 7'-0"

SWING

ALUM

EXTERIOR GLASS DOOR (PAIR)

V.I.F.

PROJECT:

LEA

LEVER

191 SMITH STREET BROOKLYN, NEW YORK 11201

3'-2"

DRAWING:

DOOR SCHEDULE, DOOR TYPES, AND TYPICAL DETAILS

ISSUE DATE :

TYPE C

03.12.2020 PROJECT NUMBER :

DRAWN BY :

CELINE LUI DRAWING :

2000 SEAL :

HOLLOW METAL DOOR; REFERENCE DOOR SCHEDULE FOR TYPE AND RATING 1 TYP. 516"

PROVIDE CONTINUOUS PLASTER GROUT AT HOLLOW METAL DOOR FRAME (TYP.).

JAMB ANCHOR AS REQ.

GENERAL DOOR NOTES

NUMBER OF HINGES PER DOOR

1. Reference A-100 series Floor Plans for door tags.

Provide 3 hinges for all doors up to 7'-6" in height.

63 TYP. 8"

63 8" TYP.

1'-8 5 16" TYP.

CONTINUOUS CHANNEL HEADER AS REQUIRED

REFERENCE PARTITION SCHED.

1'-8 5 TYP. 16"

PROVIDE CONTINUOUS PLASTER GROUT AT HOLLOW METAL DOOR FRAME (TYP.). CONTINUOUS DOUBLE STUDS AT JAMB (TYP.)

1 TYP. 516"

F.O. WALL BASE BELOW WHERE SCHEDULED

PROVIDE UNDERCUT AT DOOR SILL AS SCHEDULED (TYP.)

GYPSUM BOARD PARTITION: REFERENCE A-100 SERIES PLANS FOR TYPES AND A-400 FOR PARTITION SCHEDULE FOR ASSEMBLIES

UNDERCUT (TYP.). AS SCHEDULED

F.O. FLOOR FINISH

2 A-910

HEAD & SILL DETAILS H.M. DOOR (TYP.)

1 3" = 1'-0"

A-910

JAMB DETAIL H.M. DOOR (TYP.)

3" = 1'-0"

Provide 4 hinges for doors greater than 7'-6" in height.

DOB JOB NUMBER :

DOCUMENT :

Provide 5 hinges for doors greater than 10'-0" in height. DRAWING NUMBER:

ABBREVIATIONS

AL DR HM SCW SR STL S.STL TGL TYP. U.O.N.

Aluminum Double Rabbet Hollow Metal Solid Core Wood Single Rabbet Steel Stainless Steel Tempered Glazing Typical Unless Otherwise Noted

A-901.00 S SCAN STICKER:

FINISH SCHEDULE

REMARKS

EXISTING TO REMAIN

STONE

B.O. EX'G STRUCTURE

SUSP. ACOUSTIC PLANKS

SUSP. GYPSUM BOARD

EXISTING TO REMAIN

ALUMINUM & GLASS DOORS ENGINEERED WOOD PLANKS

ACOUSTIC PLANKS

STONE

CERAMIC TILE

GYPSUM BOARD

EXISTING TO REMAIN

WEST

ALUMINUM & GLASS DOORS ENGINEERED WOOD PLANKS

ACOUSTIC PLANKS

STONE

CERAMIC TILE

GYPSUM BOARD

EXISTING TO REMAIN

ALUMINUM & GLASS DOORS ENGINEERED WOOD PLANKS

CERAMIC TILE

GYPSUM BOARD

EXISTING TO REMAIN

ACOUSTIC PLANKS

ALUMINUM & GLASS DOORS ENGINEERED WOOD PLANKS

STONE

CERAMIC TILE

GYPSUM BOARD

NO WALL BASE

EXISTING TO REMAIN

ACOUSTIC PLANK

CERAMIC TILE, COVERED

VINYL, STRAIGHT

VINYL, COVERED

EXISTING TO REMAIN

PRECAST CONC. PAVERS

STEEL & ALUMINUM COUNTERTOP

STONE COUNTERTOP

CONCRETE FLOORING

ENGINEERED WOOD PLANKS

SOUTH

C01

KITCHEN

PATCH, SKIM COAT, AND PAINT EXISTING GYPSUM BOARD SHEATHING AT CEILING OF KITCHEN AREA

SEATING 2

C03

SEATING 3

C04

SEATING 4

C05

CLOSET

C06

PATCH, SKIM COAT, AND PAINT GYPSUM BOARD SHEATHING OF WC AREA

WALLS

CEILING

CELINE CAROL LUI DESIGN 36 BOND ST, BROOKLYN, NY 11230 CCL@GMAIL.COM 408 578 9091

REMARKS

EXISTING TO REMAIN

B.O. EX'G STRUCTURE

STONE

SUSP. ACOUSTIC PLANKS

SUSP. GYPSUM BOARD

EXISTING TO REMAIN

ALUMINUM & GLASS DOORS ENGINEERED WOOD PLANKS

ACOUSTIC PLANKS

CERAMIC TILE

GYPSUM BOARD

EXISTING TO REMAIN

WEST

ALUMINUM & GLASS DOORS ENGINEERED WOOD PLANKS

ACOUSTIC PLANKS

STONE

CERAMIC TILE

GYPSUM BOARD

EXISTING TO REMAIN

SOUTH

ALUMINUM & GLASS DOORS ENGINEERED WOOD PLANKS

CERAMIC TILE

GYPSUM BOARD

EXISTING TO REMAIN

EAST

ALUMINUM & GLASS DOORS ENGINEERED WOOD PLANKS

ACOUSTIC PLANKS

CERAMIC TILE

GYPSUM BOARD

NO WALL BASE

EXISTING TO REMAIN

ACOUSTIC PLANK

CERAMIC TILE, COVERED

VINYL, STRAIGHT

VINYL, COVERED

EXISTING TO REMAIN

PRECAST CONC. PAVERS

STEEL & ALUMINUM COUNTERTOP

CERAMIC MOSAIC DIAMOND TILES

STONE

NORTH

STONE

BASE

ACOUSTIC PLANKS

FLOOR ROOM NAME

STONE

ROOM NO.

FIRST FLOOR

CEILING

EAST

C02

STONE COUNTERTOP

FLOOR

WALLS NORTH

CONCRETE FLOORING

CELLAR

BASE

ACOUSTIC PLANKS

FLOOR ROOM NAME

CERAMIC MOSAIC DIAMOND TILES

NO.

STONE

ROOM

ENGINEERED WOOD PLANKS

FLOOR

PROJECT:

100

ENTRY

101

TO GO

102

BAR

REFERENCE MILLWORK DRAWINGS FOR ADDITION INFORMATION AND DETAILS

103

WC (ADA)

104

WC (ADA)

105

SEATING 1

106

SEATING 2

107

SEATING 3

108

SEATING 4

109

SEATING 5

LEA 191 SMITH STREET BROOKLYN, NEW YORK 11201

DRAWING:

FINISH SCHEDULE

ISSUE DATE :

03.12.2020 PROJECT NUMBER :

DRAWN BY :

CELINE LUI DRAWING :

2000 SEAL :

GENERAL FINISH NOTES

FINISH ABBREVIATIONS

1. Reference the Interior Elevations for additional finish information.

FLOOR

2. Clear Sealer to be applied at all concrete slabs exposed to view.

LCT CARP CT CRK EX'G RF WD

3. All gypsum board partitions and ceilings shall be covered by latex primer and three(3) coats of acrylic latex paint (semi-gloss); typical unless otherwise noted.

BASE Lightweight Concrete Topping Carpet Ceramic Tile, Thinset Cork Flooring Existing to Remain Resilient Flooring Wood Flooring

CT SRWB S.STL VBC VBS WB

WALLS Ceramic Tile, Coved Semi-Recessed Wood Base Stainless Steel Base Vinyl Base, Cove Vinyl Base, Straight Surface Applied Wood Base

BPG CT EX'G GL GWB HOM P-LAM

CEILINGS Back Painted Glass Ceramic Tile Existing to Remain Glass Gypsum Wall Board Homasote, Sanded Plastic Laminate

BOS SAC SAP GWB

Bottom of Structure Suspended Acoustic Ceiling Suspended Acoustic Plank Ceiling Suspended Gypsum Board Ceiling

DOB JOB NUMBER :

DOCUMENT :

01 DRAWING NUMBER:

A-920.00 S SCAN STICKER: