Wheels & Equipment Book No. 3 A range of wheels and equipment carefully chosen for the discerning potter, ceramicist or sculptor
April 2013
where quality comes as standard
Choosing a piece of equipment Buying any large piece of equipment is difficult and fraught with problems. These notes are offered as a guide to overcome problems experienced when choosing equipment such as lack of experience or knowledge of what is available. It is important in our eyes to match each individual’s desire with their budget to effectively get the best value for money. Budget is almost always the driving force behind the decision you will make. Sometimes it may be prudent to wait until you can afford the best rather than compromise on the immediate need. Generally we would argue that purchasing a piece of equipment, such as a potter’s wheel should be for life. If you think you will buy cheap and then trade up, it is probable that you will be disappointed or be conscious during use that the equipment has shortcomings. However, we would never try to argue that the cheapest model is the worst and the dearest is the best. Whatever the price, it is important to match the equipment to the user and the intended use. Each section has a description of the equipment detailed within that category. If applicable reasoning notes are also added to aid making your choice.
EQUIPMENT DELIVERY The logistics of delivering equipment is often overlooked. You must be aware how your equipment will arrive and what you may be responsible for. We would like to make all customers aware of what is included in the services we offer.
PALLET DELIVERY This service can be applied to the delivery of wheels, pugmills or any piece of equipment with external dimensions no greater than a metre square. The equipment is strapped to a pallet and delivered by means of a lorry with a tail lift. These vehicles normally have a pallet truck that can be used to manoeuvre the pallet on flat ground, but it must be appreciated that the price given is to deliver to site and off-load. It is the customer’s responsibility to remove the kiln or equipment from the pallet and move into position. Nabertherm Kilns are delivered by DHL pallet delivery service. The drivers will only off-load to the nearest convenient point. (Note: If a delivery driver offers to help further they are not covered by insurance and you are accepting responsibility for any damage that may occur to property or the equipment.)
DELIVER, OFF-LOAD INTO POSITION This is more of a tailored service and covers all sizes and shapes of equipment. Again, it is delivered by vehicle with a tail-lift. The vehicles will always have a pallet truck and the driver will off-load and move the equipment into position. A survey is requested to give the carrier information on the surfaces and site to be encountered. This service includes negotiation of no more than one step measuring 4”. Delivery of heavy equipment cannot be guaranteed on uneven or soft terrain. For large or relatively unstable equipment, assistance is requested from the customer. This service is not available to all UK locations.
2
Call us on: 01243 265845
Wheels What wheel to buy? Buying a potter’s wheel should be an exciting process, but it can also be intimiating. There are a number of variables you need to consider before making your decision. Potter’s wheels can come in many forms. The following details the different types of wheels available.
Kick or Power? Kick: Benefits
Drawbacks
Little maintenance required (just the greasing of bearings).
Not easy to use, especially for a beginner.
Choice of stand up or seated.
Not portable. Not much cheaper than the cheapest power wheel. There are two types of kick wheel; geared or momentum (the momentum is normally by having a very heavy wheelhead).
As demand for has fallen away we now longer offer any form of kick wheel in our range.
Power: Benefits Choice of 3 drive systems: Cone, Electronic (Belt drive) and Electronic (Direct drive).
Drawbacks Portabililty depends on the seating arrangement - wheels without seats will tend to be lighter and more portable that wheels with seats.
Choice of stand up, seated or a seat as an optional extra.
Types of Power Wheel: Cone or Electronic? The best known and probably biggest manufacturer of cone driven wheels was Shimpo. However, Shimpo have now ceased to manufacture cone wheels and have replaced all cone models with the “Whisper” range. As the cost of electronic wheels have fallen to a similar price for the best cone wheels we too have discontinued the supply of this format and now we only supply electronic wheels. In our view, torque (the measured ability of a rotating element) is better on electronic wheels and the transition of speed on electronic will always be smoother, especially at slower speeds (cone wheels can loose torque at very slow speeds and become jerky).
Drive Systems Electronic wheels work by varying the voltage to motor to vary the speed and all the electronic wheels we supply now use the safe AC motor in conjunction with inverter control systems
Belt Drive All Brtish built power wheels are run on belt drive systems: That is to say all the low-format and standard-format power wheel we supply - Bailey, Knightsbridge, Lincoln Electronic, Craftsman, Fitzwilliam and Wealden Throwing Wheel.
Direct Drive All American and Australian built power wheels are run on direct drive systems. That is to say all the extra-low format power wheels we supply - Shimpo Whisper range, Artists Table Top Wheel and Venco Direct Drive wheels. Direct drive eliminates the use of drive belts and bearings and therefore reduces the build cost. When replacement of worn parts is required, repair costs are greater than belt driven electronic wheels as the direct drive motor has to be dismantled. This should always be carried out by competent qualified engineers.
The drive system of cone wheels is by friction. This is a metal cone against a rubber drive ring.
Email us on: info@claymansupplies.co.uk
3
Original electronic wheels using DC motors and speed controls could be slightly jerky at 0-5 r.p.m., but this problem should not be found on any of the electronic wheels we now offer. It is strongly advised that if any wheel is attached to old wiring (i.e. without circuit breakers) a plug in RDC type circuit breaker is used between the plug and the socket. Especially with DC motors.
Format Format refers to the size and ergonomics of design: Extra Low Format: Bench mounted or with the addition of short legs. Low Format: A height of just below waist height when standing by the wheel. Standard Format: Provides a seating position where the thrower’s feet cannot touch the ground.
Casing Casings can be made from wood or have an angle iron frame with a plastic casing and pressed sheet metal. The sheet metal casing acts as a sound box. Wooden cases tend to deaden sound made by the wheels.
Additions Some wheels will accept acessories to aid a specific process. Batt holding wheelheads or studded wheelheads can be fitted to some wheels.
4
4
4
4
4
4
Standard Format
7121 - Lincoln Electronic
4
7120 - Stafforshire
4
7129 - Fitzwilliam
7112 - Shimpo RK55
4
7128 - Craftsman
7144 - Shimpo RK5T
4
7125 - Knightsbridge
7122 - Shimpo RK3E
4
Low Format
7135 - Bailey
7137 - Shimpo RK3D
Extra Low Format
7143 - Shimpo Whisper T
AT-A-GLANCE GUIDE TO THROWING WHEEL FEATURES
4 4
Seat - available as optional extra No seat
4
4
4
4
4
Integral Seat Bench mountable or table top
4
4
Additional legs (to increase height) - availabe as optional extra
4
4
Splash Tray (without drain hole)
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
Splash Tray (with drain hole) Removable Splash Tray Split Splash Tray
4
4
4
4
4
Rotation: Counter clockwise/clockwise
4
4
4
4
4
Roatationl: Counter clockwise
4
4 4
Fixed foot pedal Floating Pedal
4
4
4
4
4
4
4
4
4
4
Cordless Pedal Hand control lever Removable Wheelhead Fixed Wheelhead
4
4 4
4
4
4
4
4
4
4
4
Call us on: 01243 265845
Extra-Low Format Wheels 7143 - SHIMPO WHISPER T A new economy version of the Shimpo Whisper range. Offering a range of fantastic features at the price of other budget wheels. Made to Shimpo’s normal high standard, the Whisper T offers the beginner the opportunity to acquire a wheel that has the specification demanded by professionals. Technical Data: Motor: 300w, AC230v, 50Hz Drive System: Direct drive DC Brushless Motor with electric speed control Speed Range : 0-250 rpm Speed Control: Remote foot pedal Wheelhead Direction: Clockwise/Counter clockwise Wheelhead: Light alloy casting, 300mm diameter Dimensions: 750mm x 572mm x 580mm Weight: 53kg
7137 - SHIMPO WHISPER RK3D The RK Whisper represents the next generation of potter’s wheels. Responsive, high torque at all speeds, powerful and quiet. The exterior of the RK Whisper resembles the discontinued RK10, but that is where the similarities end! This new wheel features a brushless DC motor and direct drive (no belt) system. The motor is electronically controlled and operated by a fixed foot pedal and hand lever. It is reversible and the steel body is durable under all conditions. A 12” wheelhead and two-piece splash pan are included as standard features. Technical Data: Motor: 0.5hp, 400w, AC230v, 60Hz Drive System: Direct drive DC Brushless Motor Speed Control: Fixed foot pedal w/hand lever Wheelhead speed: 0-250rpm Wheelhead direction: Clockwise/Counter-clockwise Wheelhead: 12in. diameter alloy Dimensions: 500mm long x 525mm wide x 500mm high approx Weight: 60kg
7122 - SHIMPO WHISPER RK3E Shimpo have combined the advanced technology of the RK Whisper and the popular features of the Velocity V75 potter’s wheel to create the VL Whisper. Responsive, high torque at all speeds, powerful and extremely quiet. This wheel can also be used as a bench mounted wheel by detaching the legs. Technical Data: Motor: 0.5hp, 400w, AC230v, 60Hz Drive System: Direct Drive DC Brushless Motor Speed Control: Remote Foot Pedal Speed range: 0-250 rpm Wheelhead direction: Clockwise/Counter clockwise Wheelhead: 14” alloy Dimensions: 578mm long x 687mm wide x 569mm high approx Weight: 60kg
Email us on: info@claymansupplies.co.uk
5
7112 - SHIMPO RK55 WHEEL Shimpo’s RK-55 is a bew “budget” wheel. Technical Data: - Up to 12kg centring capacity - Three-leg design increases stability. - Built-in worktable for tools and pots. - Two-Piece Splashpan - Remote foot pedal - Modular design for compact storage. - 1.8m power supply cord - Two Year Warranty for Peace of mind. Motor: 1/8 HP 100W Drive System: DC Motor with Brush Wheelhead Speed: 0-250RPM Wheelhead Direction: Clockwise/counter Wheelhead: 300mm/12” light alloy casting Dimension: W560 x D720 x H540mm Weight 23kg
6
Call us on: 01243 265845
Low Format Wheels 7135 - BAILEY The Bailey Electronic Wheel offers the studio and professional potter a wheel of unparalleled performance and versatility in a compact and user friendly design. The wheel is powered by a super smooth 0.5hp motor that is controlled by a computer enhanced VF drive that, due to its unique design, can generate up to the peak equivalent of 1hp under heavy loads. This enables the wheel to give constant smooth power throughout the speed range and is extremely quiet in operation. The wheel is completed by its remote foot pedal which is fitted as standard. Technical Data: Motor: 0.37Kw (1/2hp) AC industrial constant rated motor. Splash tray: Moulded plastic Wheelhead: 12in. dia aluminium Construction: Precesion laser steel chasis with powder coated finish. Speed range: 0-280 rpm Speed control: Remote foot pedal Dimensions: 630mm long x 470mm wide x 680mm high approx Weight: 30kg
7125 - KNIGHTSBRIDGE The Knightsbridge Wheel has been designed and developed using extensive experience and research into control systems. It uses a 0.37kW (1/2hp) motor which is controlled by the same control unit used in our more expensive wheels. This provides unrivalled power and torque in a wheel of this size and offers an extremely quiet and smooth operation. The wheel is completed by its remote foot pedal which is fitted as standard and the wheels ability to reverse rotation at the flick of a switch. Truely an excellent wheel at a fantastic price. Technical Data: Motor: 0.37Kw (1/2hp) rubber mounted motor single phase Splash tray: Moulded polypropelene Wheelhead: 12in. dia Construction: Steel cabinet Speed range: 0-300 rpm Speed control: Remote foot pedal Dimensions: 630mm long x 470mm wide x 680mm high approx (excluding seat) Weight: 40kg
7121 - LINCOLN ELECTRONIC The Lincoln Electronic Wheel has been developed to provide a throwing wheel with unrivalled power. It is a low format design, constructed using a steel chassis with fibreglass outercase. The splash tray is made from moulded polypropulene. A strong .5hp motor powers the latest designed electronic speed control, enabling a smooth transistion of speed and unbeatable torque across the speed range of 0-280rpm. A unique feature is the ability to reverse the direction of rotation at speed by the flick of a switch. A 12in. wheelhead is fitted as standard together with a fully adjustable padded seat. There is also facility to adjust the tension of the foot pedal for comfort and maintenance of pre-set speeds. Technical Data: Motor: 0.37kW (.5hp) Bearings: Axial ball bearing sealed for life Splash tray: Moulded polyproylene Wheelhead: 12in. diameter aluminium Construction: Electrical welded steel chassis with mould fibreglass body Speed range: 0-280 rpm Dimensions: 530mm wide x 1060mm long x 685mm high approx.
Email us on: info@claymansupplies.co.uk
7
7128 - CRAFTSMAN • LOW FORMAT DESIGN • INTEGRAL SEAT • ELECTRONIC SPEED CONTROL • MULTI-ROTATIONAL • EXCELLENT SPEED RANGE 0-280r.p.m. approx. • SUPERB TORQUE • EASY REMOVABLE SPLASH TRAY The Craftsman Wheel is a design favoured by many leading craft potters in the U.K. It is constructed using a polished wooden cabinet complete with a moulded fibreglass splash tray. The drive mechanism is extremely smooth, offering low noise and vibration, whilst still produing excellent torque. Large amounts of clay can be thrown with ease and the wheel head is multi-rotational at the flick of a switch.
7129 - FITZWILLIAM • LOW FORMAT DESIGN • INTEGRAL SEAT • ELECTRONIC SPEED CONTROL • MULTI-ROTATIONAL • EXCELLENT SPEED RANGE 0-280r.p.m. approx. • SUPERB TORQUE • EASY REMOVABLE SPLASH TRAY The Fitzwilliam Throwing Wheel is a another design favoured by many leading craft potters in the U.K. It is constructed using a polished wooden cabinet complete with a moulded fibreglass splash tray. The drive mechanism is extremely smooth, offering low noise and vibration, whilst still producing excellent torque. Large amounts of clay can be thrown with ease and the wheel head is multi-rotational at the flick of a switch.
8
Call us on: 01243 265845
Standard Format Wheels 7120 - WEALDEN THROWING WHEEL The Wealden Throwing Wheel is designed and constructed to give long trouble free service for the professional or amateur potter. This wheel is constructed using a polished wooden cabinet complete with a shelf and a two position adjustable upholstered seat, the wheel incorporates a large moulded plastic bowl. The drive mechanism is extremely smooth and offers low noise and vibration characteristics whilst giving excellent torque response so enabling large amounts of clay to be thrown. Fully reversible wheelhead. Optional extras include Easy-lift Wheelhead and batts. Technical Data: Motor: 0.5hp Voltage: 220v/240v 5OHz single phase Speed: 0-280 rpm Wheelhead: 12” Double sealed top bearing for extended life Splash Tray: Moulded plastic Size: 680mm wide, 820mm high, 1000mm long Weight: 70kg (unpacked)
Wheel Accessories PLYWOOD WHEELBATTS
7168 - EASY-LIFT WHEELHEAD
Circular batts made from high quality selected exterior ply for exceptional warp resistance. Can be attached to the wheelhead using a pad of clay, locating pins(batts would need holes drilling). Sizes available:
A specialised wheelhead that can be fitted to the Bailey, Knightbridge, Lincoln, Craftsman and Fitwilliam wheels. Plywood batts are inserted to enable flatware to be made easily and removed on the batt without movement.
7149 - 8” 7153 - 9” 7150 - 10” 7154 - 11” 7151 - 12” 7156 - 13” 7152 - 15”
ALLOY WHEELHEAD Spare wheelheads that can be fitted to Bailey, Knightbridge, Lincoln, Craftsman and Fitwilliam wheels. Type of shaft needs to be specified when ordering. 7140 - 10” 7141 - 12”
STUDDED WHEELHEAD Spare wheelheads that can be fitted to Bailey, Knightbridge, Lincoln, Craftsman and Fitwilliam wheels. Type of shaft needs to be specified when ordering. 7140 - 10” 7141 - 12”
Email us on: info@claymansupplies.co.uk
9
Extruders 7500 - CLAYPRESS The Claypress extruder is built as a robust compact piece of equipment for the most demanding of artist or craftsman. It is designed to give trouble free use with a minimum amount of maintenance. The Claypress will extrude simple forms such as coils, handles etc., but can also extrude hollow sections. Coil and hollow dies are available as optional extras. The wall-mounting bracket is made from aluminium, which is cast in a series of hooks on which the handle is placed to operate the plunger. The barrel is made of 3� diameter steel tubing to which the die holder is attached by means of quick release clips for ease of die changing. Dimensions: Height: 530mm approx. Width: 140mm approx. Length: 155mm - 720mm (with handle extended) approx. Weight: 6kg approx. Construction: Aluminium body, steel barrel, steel handle, aluminium plunger
7501-Optional Hollow Die Set
7503-Optional Coil Die Set
7510 - NORTH STAR EXTRUDER PACKAGE
Here are the simplest, safest extruders available for small to medium extrusions - the kind most of us do most of the time. They have proved their utility and durability year after year. North Star extruders do not look like or work like any others. They are designed to be simple, safe and inexpensive. Both models feature a 4 inch square steel barrel tapered at the top for easy loading. Each comes with a long extension handle to give extra leverage for small extrusions or stiff clay.
10
Call us on: 01243 265845
Pugmills What is a Pugmill? Traditionally, clay was prepared by wedging and kneading. Wedging was the art of mixing dfferent consistencies of clay to form a uniform mass. Kneading was the final preparation of the clay to remove air pockets and develop the plasticity of the clay body. This is still done in many countries but a pug mill can make the task easier and quicker than the traditional manual method. Approximately one hour of pugmill use will produce enough pugged clay for an average professional potters’ days work. A pugmill is used to blend clay to restore it to a more uniform ‘workable’ consistency. This applies to new clay or clay scraps from previous work. Clay is loaded into the feed hopper and an internal auger chops and mixes the clay, pushing it along the barrel before recompressing the clay and forcing it out the nozzle. The de-airing models incorporate a vacuum pump which removes air trapped within the clay whilst pugging is performed. This produces the highest quality clay for immediate use on a potter’s wheel. Tradtionalists can still argue that kneading will still produce a better clay and also a “feel or knowledge” of the clay body to the user. The hopper mouths and nozzle should always be covered with plastic when not is use to avoid the clay in the barrel from drying out. Ideally the barrel of any pug should be cleaned out once a year.
7600 - 2” MINI WITH HOPPER The economy range of pugmills has been specifically designed for the studio and classroom environment. They are compact and lightweight making them easily transportable. This model is fitted with a hopper safety grid and thermal overload safety switch as standard. Technical Data: 4” (100mm) Aluminium Body 2” (50mm) Extrusion Body and nose cone for easy cleaning Individual nylatron blades mounted on a hexagonal steel shaft Geared motor reduction drive Single or three phase Safety switch and overload starter Output 190-200kg per hour approx.
Overall Dimensions Height: 470mm approx Width: 280mm approx Length: 800mm approx Weight: 36.5 Kg approx
7600/MS - 2” MINI WITH MICRO-SWITCH This model has the same specification as 7600, but it is fitted with a interlocked hopper safety switch. This switch, together with its high torque motor, makes the pugmill extremely easy to load as there is no safety grid in the hopper to impede the flow of clay. When the loading handle is raised the machine switches off and then on again when the loading handle is lowered. Thermal overload safety switch is fitted as standard.
7601 - 3” MINI WITH HOPPER The same compact design as the 2” Mini, but has a larger 150mm barrel with a 75mm (2in.) outlet. This version has a greater output and, due to its larger hopper, is easier to use than the smaller 2” model. A thermal overload switch is fitted as standard. Technical Data 6” (150mm) aluminium body 3” (75mm) extrusion body and nose cone for easy cleaning Individual aluminium blades mounted on a hexagonal steel shaft Geared motor reduction drive Single or three phase Safety switch and overload starter Output 300kg per hour approx
Overall Dimensions Height: 500mm approx Width: 280mm approx Length: 800mm approx Weight: 78kg approx.
7601/MS - 3” MINI WITH MICRO-SWITCH The same specification as the 7601 version , but is fitted with a interlocked hopper safety switch negating the need for a hopper grid.
Email us on: info@claymansupplies.co.uk
11
7620 - 3” VERTICAL
This vertical pugmill has a 150mm split aluminium barrel with a 75mm outlet and individual alloy blades mounted on a hexagonal shaft. It offers superior performance over conventional horizontal pugmills, but has the advantage of only taking up a 60cm x 60cm foot print. The pugmill is sturdily mounted on its own stand, which only requires securing to a suitable floor. Technical Data Drive: 0.75kW (1hp) with helical reduction gearbox Construction: All aluminium body 150mm in diameter with a 75mm out let, fitted with Alloy blades mounted on a hexagonal shaft with taper roller bearings, split body for easy cleaning. Thermal over load starter with safety interlocked switch Output: 360kg per hour Overall Dimensions Depth: 711mm approx. Width: 609mm approx. Height: 1980 mm approx. Weight: 123kg approx.
7625 - 4” VERTICAL DE-AIRING
The 100mm (4” ) vertical pugmill is extremely powerful and robust with the ability to handle all types of clays. The main body is manufactured from aluminium, with an auger, also made up of individual alloy blades. The auger is mounted through two taper thrust bearings and is driven via a flexible coupling by a 1.1kW (1.5hp) helical geared motor, with a final drive output of 18rpm. It is fitted with a safety interlock switch which eliminates the need for a grid in the loading hopper and is supplied with a separate nose cone that is pre-drilled to enable the use of die plates for coil extruding. Technical Data Voltage 220—240 V, 50 Hz Single phase, 380— 415 V, 50 Hz Three phase. Output: 700kg per hour approx. Overall Dimensions: Length: 760mm approx. Width: 760mm approx. Height: 2300mm approx. Weight: 300kg approx.
12
Call us on: 01243 265845
7627 - TILE EXTRUDER The tile extruder is a very versatile machine, besides extruding tiles, mouldings and coils etc can be extruded with the use of optional die plates. Using the standard 100mm dia. nose cone supplied with the machine enables other shapes, such as hollow forms to be extruded, again with the use of optional die plates. The tile extruder is a purpose designed machine for the extrusion of tiles. It has been designed around the standard de-airing pugmill, but using a larger higher torque motor gearbox unit. The machine is also fitted with a completely new nose cone outlet designed to enable tiles of approximately 280mm width by up to 25mm thick to be extruded. Smaller and /or thinner tiles can also be extruded by the use of accessory die plates fitted to the front of the nose cone. Technical Data: Construction: All aluminium alloy construction with split body to aid easy cleaning. Individual aluminium alloy blades mounted on a hexagonal shaft. Supplied with all switch gear and an interlocked hopper safety switch. Motor gearbox unit: 2.2kW (3hp) single or three phase Vacuum pump: High pressure rotary vane oil immersed –28” (-1 Bar) Bearings: 2 adjustable taper roller bearings, oil seal and retaining plate. Output: 60 -80 sq ft/ hour approximately. Output depends on clay body condition (softness), tile dimension, number of operators etc. With standard nose cone fitted out put is rated at 500kg per hour.
Overall Dimensions: Length: 905mm approx. Width:609mm approx. Height: 1040mm approx. Weight: 270kg approx. Standard accessories:- 1- 150mm x 5mm die plate
Optional extras: Extruding table, Ware boards, Tile Cutting System, Die plates, Stainless steel auger
7627/1 - TILE CUTTING TABLE This cutting table has been designed to compliment the tile extruder pugmill. The cutting system comprises a table with formica top. A central rotary shaft secured by sealed roller bearings, which are adjustable to allow for different thicknesses. On the shaft are mounted sixteen cutting discs. As the wareboard of extruded clay is pulled by the operating lever, the cuttings discs are pulled through the clay.
7627/2 - EXTRUDING TABLE Another addition to compliment the tile extruding pugmill. The table consists of a rigid base supporting a fully adjustable top. The adjustment allows for varying thicknesses of extrusion. On the suraface of the table is a paper roll, which allows extrusion to run without buckling. Overall Dimensions: Length: 1830mm approx. Width: 510mm approx. Height: 600mm variable
7333 - BIN DOLLEY
4901 - PLASTER SINK
The easiest way to move bins of clay or glaze around the workshop. Adjustable to suit most size of bin.
Email us on: info@claymansupplies.co.uk
Every potter’s workshop will have reclaim clay. The problem the potter faces is how to deal with the process of recycling this product. With the plaster sink the reclaim can be spread within the sink to dry. The walls retain the clay whatever its condition (liquid or otherwise) from spilling. Our plaster sink is the simple and tidy way to control your reclaim before pugging.
13
Slab Rollers 7210 - SLAB ROLLER 3’ & 7211 SLAB ROLLER 4’ The Clayman Slab Roller has been designed to provide extremely efficient and reliable methods of producing slabs of clay for hand building or tiles. It has been designed using vast experience in slab roller production and incorporates a rack and pinion drive system, eliminating the need of maintenance from troublesome wire driven systems, the design allows for infinitely variable thickness of clay to be rolled by means of adjustment of the main roller using a simple threaded adjuster that allows for fine adjustment whilst keeping the equal distance above the table across its length. The large single roller is made of a rust proof material to avoid corrosion or contamination of the clay. The slab roller has fully collapsible legs so it can be easily transported and comes complete with a set of high quality rolling cloths 7210 - Technical Data: Overall Dimensions: Size: 1090mm high x 820mm wide x 920mm long Slab Size: 720mm long x 470mm wide Weight: 60kg 7211 - Technical Data: Overall Dimensions: Size: 1090mm high x 820mm wide x 1220mm long Slab Size: 1020mm long X 470mm wide Weight: 70kg approx Please note slab size can only be given as a approximation due to the different natures of clay used.
7214 - MOTORIZED SLAB ROLLER
The Motorised slab roller is fully automatic , the operator simply places the clay on the slab roller adjusts to the required thickness closes the interlocked safety cage and then presses the cycle button . The slab roller will then make two passes over the clay and then come to a complete stop. It is labour saving i.e. whilst the clay is being rolled it leaves you free to proceed with other duties around the class room or studio, extremely safe in operation , out standing results are produced from the combination of constant pressure at a set speed , ideal for the handicapped or physically impaired. The slab roller uses the same excellent standard of engineering as our other slab rollers. The main roller is manufactured from corrosion resistant alloy and has infinite adjustment between approximately 2mm and 30mm via a centrally mounted threaded adjusting handle, thus eliminating the need for packing boards. Technical Data: Drive: 0.37 Kw (0.5 Hp) worm reduction 1 phase or 3 phase Speed control: Variable speed with full logic control Safety: Fully enclosed and electrically interlocked safety cage Power supply: 220/240 v50Hz/60Hz 380v 415 v Slab size: 1020 mm x 470 mm wide Dimensions : 1200 mm high x 915 mm wide x 1220 mm long Weight: 90 Kilos
14
Call us on: 01243 265845
Spray Booths Our spray booths are suitable for glaze and slip spraying. 7801 is designed to be ducted to the atmosphere, the other models are self contained units.
7801 - DRYBACK SPRAY BOOTH This Spray Booth has been designed for use in the classroom or small pottery workshop. The booth is fitted with a 12” electric extractor fan which produces an air velocity of 250 cfm at the face. A stand and washable heavy duty filter are fitted as standard. Technical data: Spray Booth Width: 24” (610mm) approx. Height: 24” (610mrn) approx, Depth: 35.5” (890mm) approx. Stand Width: 24”(610rnrn) approx. Depth: 18” (450rnm) approx. Height: 30” (900mm) approx. Power supply: 220/240v l phase Weight: 21Kg approx. NOTE: Only suitable for water based material
7800 - WATERFALL SPRAY BOOTH This Waterfall Spray Booth has been designed to meet the ever increasing need to protect our environment. The water wash spray booth works on the principle of a curtain of continuous recycling water running down the rear face of the spray booth, a glaze spray is aimed towards this curtain, the spray being guided by a powerful extraction fan, the glaze is trapped by the water curtain, whilst the air stream is pulled through the booth and into a washable stainless steel pre filter and finally into a washable filter bag. The excess glaze is washed into the tank and can at a later date be reclaimed depending on the type and colour of the glaze. There is a ball valve to allow the water to be drained and the contents of the tank removed. Any glaze materials can also be removed and disposed of safely. The booth is mounted on four castor wheels. The 7800 is primarily designed to be used by the studio potter and educational faculties for low volume production, therefore the booth does not need ducting to atmosphere making it portable around the studio environment. This spray booth uses a sophisticated baffle system to prevent water take through into the filter bag, they are designed to be used with water based material only, but can be adapted if required for solvents. If the spray booth is to be used in a production environment it may be necessary to duct to the atmosphere, please contact our technical department is you require further advice. Technical data: Height: 1580mm approx. Width: 820mm approx. Depth: 1290mm approx. Fan: 2000CFM Air extraction: 250 Cu Ft/min Steel construction Internal parts: stainless steel Water tank: Polypropylene Switchgear: Thermal overload protection Weight: 118 kg approx. Power: 220/240v 5OHz Hood internal dimensions: 638mm x 625mm x 420mm deep. Working depth: 350mm
Email us on: info@claymansupplies.co.uk
15
7805 - WATERFALL SPRAY BOOTH This Waterfall Spray Booth has been designed to meet the ever increasing need to protect our environment. The water wash spray booth works on the principle of a curtain of continuous recycling water running down the rear face of the spray booth, a glaze spray is aimed towards this curtain, the spray being guided by a powerful extraction fan, the glaze is trapped by the water curtain, whilst the air stream is pulled through the booth and into a washable stainless steel pre filter and finally into a washable filter bag. The excess glaze is washed into the tank and can at a later date be reclaimed depending on the type and colour of the glaze. There is a ball valve to allow the water to be drained and the contents of the tank removed. Any glaze materials can also be removed and disposed of safely. The booth is mounted on four castor wheels. The 7800 is primarily designed to be used by the studio potter and educational faculties for low volume production, therefore the booth does not need ducting to atmosphere making it portable around the studio environment. This spray booth uses a sophisticated baffle system to prevent water take through into the filter bag, they are designed to be used with water based material only, but can be adapted if required for solvents. If the spray booth is to be used in a production environment it may be necessary to duct to the atmosphere, please contact our technical department is you require further advice. Technical data: Height: 1580mm approx. Width: 820mm approx. Depth: 1290mm approx. Fan: 2000CFM Air extraction: 250 Cu Ft/min Steel construction Internal parts: stainless steel Water tank: Polypropylene Switchgear: Thermal overload protection Weight: 118 kg approx. Power: 220/240v 5OHz Hood internal dimensions: 638mm x 625mm x 420mm deep. Working depth: 350mm
6998 - GLECO TRAP
6999 - CLAY TRAP
The Gleco Trap is an innovative, inexpensive solution in preventing clay and glaze materials blocking waste pipes. The system easily fits most standard sink cabinet areas and is easily maintained. Recommended for light to medium use. The Gleco Trap is easily installed. The trap is connected below the sink and collects solids in a bottle, which has a fill line. when the solids reach the fill line, the trap is drained through a valve, the bottle is exchanged with a replacement bottle, the valve shut and the trap is back in service. Bottle exchange is rapid and done without the need of tools (less than 2 minutes).
16
The Clay Trap measures 552 x 400 x 270mm deep. The cut-away lid in our illustration reveals the two weirs, the inlet on the left and the outlet, which has a 76mm water seal on the right. Both inlet and outlet have coupling nuts for joining to 38mm ‘Vulcathene Mechanical’ pipe. Recommended for medium to heavy use.
Call us on: 01243 265845
Spray Equipment 6800 - BASIC SPRAY GUN Simple but effective spray for modelling, stencilling, texturing and ceramics, for spraying medium to heavy viscosity fluids, and simple enough for children ages 8 and up. Sprays 18mm - 50mm by adjusting the tip. Supplied in a blister pack. The pack includes 22ml jar, vinyl hose and regulator. It can be used from a propellant can in conjunction with the regulator, or from a compressor (.25” adaptor required – optional extra) or a deflating car tyre (valve adaptor required – optional extra).
6606 - IWATA POWERJET COMPRESSOR Iwata Studio Compressors are powerful, compact and quiet. With oil-less pistion motors, they are low maintenance and affordably priced. The Power Jet Plus Handle Tank compressor, like its name suggests, has the feature of a 480cc air tankinside the handle. It is powerful enough to run up to four airbrushes (a multiple-oulet manifold is required) or a small spray gun.
6602 - DEFYNIK COMPRESSOR & SPRAY GUN
6801 - MINI SPRAY GUN Simple but effective spray for modelling, stencilling, texturing and ceramics for spraying medium to heavy viscosity fluids, and simple enough for children ages 8 and up. Sprays 18mm - 50mm by adjusting the tip. The pack includes 120ml jar, vinyl hose and regulator. It can be used from a propellant can in conjunction with the regulator, or from a compressor (.25” adaptor required – optional extra) or a deflating car tyre (valve adaptor required – optional extra).
An economy combination of 6601 Junior Spray Gun with 6600 777 Compressor. A continuous diaphragm type compressor with a suction spray gun, including a 1 litre capacity jar. Spray Gun includes a round spray and fan spray nozzle.
6601 - JUNIOR SPRAY GUN • Pressure gun (low pressure). • With continuous air outlet. • Maximum pressure: 3,5 bar. • Pressurized tank and internal mixture aircaps. -• Air consumption: 85 l/min.-3,5 bar. • Weight: 650 g
This item is the same as 6800 with the exception of the jar size.
A well proven suction type spray gun, offering a round spray and fan spray nozzle. Ideal for spraying large areas of glaze.
6803 - TYRE ADAPTER An adaptor to enable the connection of an air brush regulator to a car tyre valve. The tyre must be on the rim and requires inflating. The spray operates by deflating the tyre.
6609 - SAGOLA JUNIOR G SPRAY GUN
6804 - 0.25” ADAPTOR
An adaptor that enables a .25” air hose, used with airbrushes and the Basic and Mini Spray Guns to be connected to a compressor.
• Gravity Spray Gun • With Air Valve • Single shaft design, less parts • Low air consumption • Maximum robustness and reliability • Designed for working at pressures under 3.5 bar (50psi) Light and economical gravity spray gun, high transfer and very low air consumption. Robust, light and with new ergonomic design.
6808 - AIR PROPELLANT 750g 750ml can of propellant for use with airbrushes or the Basic and Mini Spray Guns.
Email us on: info@claymansupplies.co.uk
17
6608 - PAINTEC SPRAY GUN Introducing the new Paintec hand operated spray gun. The simple but cost effective way to spray glaze and colours. The Paintec Sprayer has been developed especially for potters, with the finest quality plastic and bronze components to assure chemical resistance. What makes this item stand out? •ECONOMICAL •ADJUSTABLE •SPRAYS CONTINUOUSLY •NO COMPRESSOR REQUIRED •NO POWER SUPPLY REQUIRED •LIGHT & COMFORTABLE TO USE The Sprayer is supplied with a 0.6mm nozzle as standard, which enables glaze to be sprayed that has passed through an 80’s mesh sieve and colour that has passed through a 120’s mesh. Larger nozzles are available as optional extra. How to use the Paintec Sprayer? Simply pump four or five times to start to spray, then pump from time to time to maintain a continuous pressure thanks to an exclusive stainless steel retention valve. The pressure pump is designed to obtain maximum pressure with minimal effort. NO POWER SUPPLY REQUIRED No electricity or batteries are required. It can be used anywhere, at any time and is very quiet in use. Although it is not necessary to use the Paintec with a compressor it is possible to connect to a compressor if required (optional extra).
6608/3 - PAINTEC NOZZLE SET
6608 - PAINTEC SPRAY GUN
Nozzle Set contains 0.8mm, 1.0mm and 1.2mm nozzles.
The perfect way to convert the Paintec Spray Gun for use with a compressor
6608/11 - PAINTEC SMALL CONTAINERS
6608/7 - PAINTEC SPARE BOTTLE & CAP
Additional small containers supplied in packs of three. These are used with the Paintec Spray Gun to enable small amounts of colour to be sprayed.
A spare 1 litre jar for the Paintec Spray Gun. Supplied with screw on cap to enable jar to be used for storage of glaze or colour.
18
Call us on: 01243 265845
Whirlers Whirlers can also be known as Banding Wheels. they are metal turntables that are used on a work top to aid the decoration and making of ceramics. Alloy whirlers are lighter and easy to transport, therefore especially good for modelling. Steel whirlers are heavy and ideal for banding lines onto plates or bowls as they will spin for longer. All whirlers have concentric circles etched into the working surface to aid “re-centring” of work in progress. Also very useful in a Spray Booth for turning pireces that are being sprayed.
6700 - 6706 - WHIRLERS
6711 - 6712 - WHIRLERS
6700 - 8 x 4” STEEL WHIRLER
6711 - 20 x 7cm CAST IRON WHIRLER
6701 - 8 x 6” ALLOY WHIRLER
6712 - 25 x 7.5cm CAST IRON WHIRLER
6704 - 8 x 3” ALLOY WHIRLER
6709 - ADJUSTABLE MODELLING STAND A inexpensive simple modelling stand. The height is easily adjusted and the “head” turns freely. Also included is a useful tool rest.
6705 - 10 x 4” ALLOY WHIRLER
6706 - 12 x 6” ALLOY WHIRLER
Email us on: info@claymansupplies.co.uk
19
Miscellaneous Equipment DAMP CABINETS The construction of these damp cabinets is zinc coated sheet steel, which is powder coated externally. The doors are fItted with neoprene seals and lockable handles. Each cabinet includes four removable shelves. To obtain a moist atmosphere the base can be lined with damp plaster blocks (not included). 7700 - Technical Data: Size: 1220mm wide x 1220mm high x 610mm deep Weight: N/A 7701 - Technical Data: Size: 910mm wide x 1220mm high x 610mm deep Weight: N/A 7702 - Technical Data: Size: 1220mm wide x 1830mm high x 610mm deep Weight: N/A 7703 - Technical Data: Size: 910mm wide x 1830mm high x 610mm deep Weight: N/A
DRYING CABINETS These Drying Cabinets are designed to aid the drying of moulds and clay ware. Each cabinet is constructed of zinc coated steel with two vertical hinged front opening door.. All Drying Cabinets have a on/off temperature control switch and can be operated from a 13amp supply. Technical Data: Supply: 3kW -220v/240v - 5OHz single phase Size: 1830mm wide x 1220mm high x 575mm deep Weight: N/A
SLABBING & WEDGING BENCHES Our benches are specifically designed for classroom and studio use. They are made from sustainable environmentally friendly materials and are a robust design to withstand years of use. The benches are finished to a high standard with attention to detail being paramount to ensure long life and ease of use. 7164 - SLABBING BENCH Technical Data: Construction - Soft wood frame sanded and polished to a high finish. Bench top - 20mm Formica top Dimensions - 1200mm long x 860mm x 760mm high Note: “H” design stiles available on request A professional wedging bench, which incorporates the same quality wooden frameas our work benches, but incorporates a compressed concrete top. Ideal for wedging and kneading clay 7166 - WEDGING BENCH Technical Data: Construction - Soft wood frame sanded and polished to a high finish. Bench top - 50mm compressed concrete Dimensions - 1200mm long x 660mm x 760mm high Note: “H” design stiles available on request
20
Call us on: 01243 265845
Mixers 7001 - RAPID MIXER
A simple item of workshop equipment designed for the speedy mixing of glazes or slips. In use water is placed in the container, followed by the mixer. The dry materials are added while the mixer is turning. The mixer has a 1/6hp motor driving a stainless steel shaft and vaned alloy impeller. A handle is fitted for ease of lifting. The rapid mixer is supplied with 25litre plastic container. N.B – If using to mix any material of high viscosity (i.e. casting slip) the mixer should be running before inserting into the material. Technical Data: Size: Diameter :55mm Height: 610mm Weight: 25kg:
7007 - VIBRATORY SCREEN
An electrically operated screen for slip or glaze. Fitted with 8� (204mm) diameter mesh. Three sizes of mesh are available 60, 80 or 120 mesh. Technical Data: Overall size: Width: 365mm approx. Depth: 458mm approx. Height: 508mm approx. Weight: 9kg approx. Electrical Supply: 220/240v Single Phase
Email us on: info@claymansupplies.co.uk
21
Plaster Working Equipment 7714 - REVERSIBLE TURNING LATHE This lathe is an invaluable addition to the mould makers workshop. A .5hp motor transfers drive to the shaft via a V belt and pulley. The speed is controlled by a AC electronic speed control, which has a reversible facility. The machine is totally enclosed for safety and is supplied complete with an adjustable tool rest. Technical Data: Motor: .5hp AC Speed control: Variable electronic Speed range: 0-380rpm Bearings: Sealed for life, self-aligning Size: 410mm high x 470mm wide x 1220mm long Weight: 90kg (approx.) Optional extras: Foot operated control Tapered steel spindles: 150mm, 230mm, 300mm and 380mm Aluminium face plates: 150mm, 200mm, 250mm diameter
7720 - VACUUM PLASTER MACHINE Technical Data: Capacity: 3-5 gallons Drive unit: 0.37kW geared drive, output speed 500rpm Shaft: Stainless steel shaft and bronze blades Size: 1.9m high x 720mm deep x 650mm wide Weight: 140kg (approxx.) Optional extras: Blending jugs, visual indicators for time duration
7721 - PLASTER BLENDER The Plaster Blender mixes plaster quicker and more efficiently than by hand and produces a more consistent plaster mix. The blender is free standing and has a mixing head driven by a 0.37kW inline motor and gear unit. The mixer is raised or lowered by means of a counter balance guide platform. Each blender is supplied with a switchgear and a timer unit allowing for automatic cut off after a pre-determined mixing period. Technical Data: Capacity: 3-5 gallons Drive unit: 0.37kW geared drive, output speed 500rpm Shaft: Stainless steel shaft and bronze blades Size: 1.9m high x 720mm deep x 650mm wide Weight: 140kg (approxx.) Optional extras: Blending jugs, visual indicators for time duration
7722 - MODELLING BENCH This Modelling Bench is constructed of a sturdy rectangular steel frame and is driven via a variable speed electric motor. A speed range of 0-250rpm with high torque is available. A 12� plaster prong or 12� wheelhead is supplied with each bench. Technical Data: Overal Dimensions: 600mm (wide) x 750mm (deep) x 800mm (high) to Bench bed or 900mm (high) to top of wheelhead Overall to top of Shaving Guard when fitted(Optional Extra): 1170mm Motor: 0.37kW AC Speed Control: AC Inverter Voltage: 230 Speed: 0.250rpm Weight: 90kg approx.
22
Optional Extras: Shaving Guard Tool Rest
Call us on: 01243 265845
Slip Equipment 7300 -15 gallon BLUNGER - 7304 - 25 gallon BLUNGER
Blunging is the process of producing casting slip from plastic or powdered clay. This model uses two paddles which rotate at 150rpm approximately on a stainless steel shaft. Drive is via a 0.75kW motor through a reduction gearbox. The drum is fibreglass fitted with a extended loading shute for safety. A stand is available as a optional extra. Technical Data: 7304 - 25gallon BLUNGER - Technical Data: Overall Dimensions: 800mm wide x 1000mm deep x 1100mm high approx. Weight: 50kg Capacity: 25gallons
7310 -SLIP CASTING CENTRE
This design is the 7311 Slip Pump fitted into a self-contained fibreglass tank. Removable wooden casting rails are fitted for ease of mould draining. The whole unit is mounted on castors. A drain plug at the bottom of the tank is for emptying and cleaning. Technical Data: Overall Dimensions: 530mm wide x 1040mm deep x 1140mm high Weight: 22kg
7311 -SLIP PUMP The Slip Pump is a highly versatile method of slip dispensing for both studio and hobby ceramics. The pump uses a rotary vaned design capable of giving a good, even flow. The pump also has an agitating effect to maintain usable conditions. A syphoning action can also be used to aid the draining of moulds. Technical Data: Overall Dimensions: 300mm wide x 300mm deep x 800mm high Container Capacity: 10gallons Motor & Switch: 0.5hp single phase Weight: 14.5kg
Email us on: info@claymansupplies.co.uk
23
Notes
24
Call us on: 01243 265845
Notes
Email us on: info@claymansupplies.co.uk
25
Conditions of Sale 1. Payment
6. Non-Delivery/ Partial Loss
Credit is allowed to Education Authorities and similar bodies and will be allowed to other customers on receipt of acceptable trade and bank references. Payment of accounts is to be made within 30 days nett of invoice date. NON-PAYMENT WITHIN THE THIRTY DAYS WILL BE SUBJECT TO AN INTERST CHARGE. Unless otherwise agreed, where no credit account exists, all orders must be accompanied by remittance to the value of the order including carriage and VAT. Payment may be made by cash, cheque, credit or debit card.
In the event customers must give notice in writing to the carrier and ourselves within three days of receipt of goods.
2. Prices All goods are invoiced at prices ruling at date of despatch and are accepted only on this basis. All prices are subject to change without notice. All prices printed in price lists, advertising matter and elsewhere, submitted in writing or stated verbally are, unless otherwise stated, nett ex-works, carriage and VAT extra.
3. Quotations Quotations for the delivery of goods, equipment and kilns will be submitted on receipt of all relevant information.
4. Carriage Off-loading and moving into position is the responsibility of the customer unless special arrangements have been made.
5. Delivered Goods Although we make every effort to adhere to stated delivery times, such times do not bind us and we shall be under no liability for any loss or damage of whatever nature caused by delay.
7. Damage If possible, goods should be examined in the presence of the deliveryman and if any package appears damaged, the consigment/ delivery note should be endorsed accordingly. Customers must advise the carrier in writing of any damage within three days of delivery and present a detailed claim to the carrier within seven days of delivery, with copies to ourselves.
8. Description & Specification All descriptions, specification, drawing or illustrations shown in literature as advertising matter, given verbally or in writing are given for general guidance only and no warranty or guarantee of any kind is to be implied nor is such information to form part of any contract. In accordance with out policy of constantly improving products we reserve the right to change specification or delete any items from our catalogue, without prior notice. THE BUYER IS STRONGLY RECOMMENDED TO TEST ALL GOODS BEFORE USING THEM AND WHERE A BULK MATERIAL IS TO BE USED IT IS RECOMMENDED THAT A SAMPLE BE TESTED FIRST.
9. Liability We accept no liability for death, injury or damage if any kind whether to person or property arising out or in connection with any material, goods or services by us.
10. Ownership The ownership of goods bought shall not pass to the Purchaser until the Purchaser has paid to the Company the total purchase price, including VAT, in respect of said goods.
Contact details Postal Address:
Clayman Supplies Limited Morells Barn Park Lane Lower Bognor Road Lagness Chichester West Sussex PO20 1LR Telephone & Fax Numbers:
Telephone: Fax:
01243 265845 (24 hour ansaphone) 01243 267582
Internet:
Email: General Information: info@claymansupplies.co.uk Sales: sales@claymansupplies.co.uk Account queries: accounts@claymansupplies.co.uk Website: www.claymansupplies.co.uk
26
Call us on: 01243 265845