Standard Angle Fitting Bundle – VR205
Fixed End Fitting x 1 VR308
BY
Angle Threaded Crimp Fitting x 1 Angle Tension Receiver x 1 Angle Insert Sleeve x 2 VR306 VR305 VR335
Angle Washer x 2 VR345
*Component quantities per Bundle
Fixed End Fitting
Angle Insert Sleeve
Angle Washer
Angle Threaded Crimp Fitting
Post
CRIMP FIRST
Angle Tension Receiver Angle Washer
Post
CRIMP LAST
INSTALLATION INSTRUCTIONS *Fittings require 1/2 inch holes. 1. Slide the cable into the Fixed End Fitting until the cable is flush with the end of the Fixed End Fitting. Double crimp the Fixed End Fitting onto the cable. (See Diagram 1)
4. Slide the cable into the Threaded Crimp Fitting until the cable is flush with the threads. Double crimp the Angle Threaded Crimp Fitting onto the cable (See Diagram 1).
1 2 3 Each crimped fitting should be crimped twice (as shown). Check crimper dies occasionally to ensure that it is creating a secure, hexagonal crimp. CUT HERE
CABLE
DIAGRAM 1
5. Slide the Angle Washer onto the Angle Tension Receiver, then insert the Angle Tension Receiver into the post and tighten it onto the Angle Threaded Crimp Fitting by hand.
POST
6. Repeat steps 1-5 for all cables.
3 3
7. Use the supplied tightening tool to hold Angle Threaded Crimp Fittings from rotating. Turn the Angle Tension Receiver with the supplied Allen Wrench. Tighten the center cable first, then alternate (one higher, one lower) until all cables have been tightened.
CABLE
8. Tap Angle Insert Sleeves into the posts to finish installation. 9. Thoroughly clean the cables and all fittings. Trace amounts of iron may be on your stainless steel from tools and handling. The trace iron can rust or discolor your Viewrail installation. [continued on reverse side]
2 2
3. Hold the cable up to the side of the end post, pull the cable taut, mark and cut the cable 1 1/2" from the outside edge of the post. Be sure that the Fixed End Fitting is seated into the Angle Washer properly. (See Diagram 2).
POST
1 1
2. Thread the cable through posts, making sure to put Angle Insert Sleeves on the cable as you go. Double check that the Angle Insert Sleeves and Angle Washers are facing the correct direction. The point of the Angle Washer should be pointing at the post [see diagram above].
CUT HERE DIAGRAM 2
STAI
Standard Angle Fitting Bundle – VR205 [continued]
BY
Angle Tension Receiver
Angle Washer Angle Insert Sleeve
Angle Insert Sleeve
Angle Washer
Fixed End Fitting
STAI
Dual Tension Level Fitting Bundle – VR212
Threaded Crimp Fitting x 2 VR302
Tension Receiver x 2 VR301
BY
Insert Sleeve x 2 VR330
*Component quantities per Bundle
Threaded Crimp Fitting
Threaded Crimp Fitting
Tension Receiver
Insert Sleeve
Tension Receiver
Insert Sleeve
Post
Post
CRIMP HERE
CRIMP HERE
INSTALLATION INSTRUCTIONS *Fittings require 1/2 inch holes. 1. Slide an Insert Sleeve onto the cable, then slide the cable into the Threaded Crimped Fitting until the cable is flush with the end of the Threaded Crimped Fitting. Double crimp the Threaded Crimped Fitting onto the cable. (See Diagram 1) 2. Insert the Tension Receiver into the post and tighten it onto the Threaded Crimp Fitting by hand. Thread the cable through posts. 3. Hold the cable up to the side of the end post, pull the cable taut, mark and cut the cable 1 1/2� from the outside edge of the post. Be sure that the other Tension Receiver is seated into the post hole properly. (See Diagram 2). 4. Slide an Insert Sleeve onto the cable, then slide the cable into the Threaded Crimp Fitting until the cable is flush with the threads. Double crimp the Threaded Crimp Fitting onto the cable (See Diagram 1).
POST
1 2 3 Each crimped fitting should be crimped twice (as shown). Check crimper dies occasionally to ensure that it is creating a secure, hexagonal crimp. CUT HERE
CABLE
DIAGRAM 1
5. Insert the Tension Receiver into the post and tighten it onto the Threaded Crimp Fitting by hand. POST
2 2
3 3
7. Use the supplied tightening tool to hold Threaded Crimp Fittings from rotating. Turn the Tension Receiver with the supplied Allen Wrench. Tighten the center cable first, then alternate (one higher, one lower) until all cables have been tightened.
1 1
6. Repeat steps 1-5 for all cables.
CABLE
8. Tap Insert Sleeves into the posts to finish installation. 9. Thoroughly clean the cables and all fittings. Trace amounts of iron may be on your stainless steel from tools and handling. The trace iron can rust or discolor your Viewrail installation.
CUT HERE DIAGRAM 2
STAI
Steel Inside Post Level Fitting Bundle – VR222
Cable Stop x 1 VR312
Threaded Crimp Fitting x 1 VR302
Tension Receiver x 1 VR301
BY
Steel Inside Post Washer x 1 VR315
*Component quantities per Bundle
Insert Sleeve x 1 VR330
Short Insert Sleeve x 1 VR332
Steel Inside Post Washer Cable Stop
Insert Sleeve Short Insert Sleeve
Threaded Crimp Fitting
Post
CRIMP FIRST
Tension Receiver
Post
CRIMP LAST
INSTALLATION INSTRUCTIONS *Fittings require 1/2 inch holes. 1. Slide the Short Insert Sleeve, Steel Inside Post Washer, and Cable Stop onto the cable. Slide the Cable Stop until the cable is flush with the end of it. Double crimp the Cable Stop onto the cable. (See Diagram 1)
4. Hold the cable up to the side of the end post, pull the cable taut, mark and cut the cable 1 1/2" from the outside edge of the post. Be sure that the Cable Stop and Steel Inside Post Washer are seated into the post hole properly. (See Diagram 2). 5. Slide the cable into the Threaded Crimp Fitting until the cable is flush with the threads. Double crimp the Threaded Crimp Fitting onto the cable (See Diagram 1).
DIAGRAM 1
6. Insert the Tension Receiver into the post and tighten it onto the Threaded Crimp Fitting by hand.
POST
7. Repeat steps 1–6 for all cables.
3 3
8. Use the supplied tightening tool to hold Threaded Crimp Fittings from rotating. Turn the Tension Receiver with the supplied Allen Wrench. Tighten the center cable first, then alternate (one higher, one lower) until all cables are tightened.
2 2
3. Thread the cable through posts, making sure to put Insert Sleeves on the cable as you go. (Double check that the Insert Sleeves are facing the correct direction).
1 2 3 Each crimped fitting should be crimped twice (as shown). Check crimper dies occasionally to ensure that it is creating a secure, hexagonal crimp. CUT HERE
CABLE
1 1
2. Insert the Cable Stop into the post and tap the Steel Inside Post Washer through the hole. Once the Steel Inside Post Washer is inside the post, push the cable into the post then pull it tight until the washer lies flat against the inside of the post.
POST
CABLE
9. Tap Insert Sleeves into the posts to finish installation. 10. Thoroughly clean the cables and all fittings. Trace amounts of iron may be on your stainless steel from tools and handling. The trace iron can rust or discolor your Viewrail installation.
CUT HERE DIAGRAM 2
STAI
Steel Inside Post Angle Fitting Bundle – VR225
Cable Stop x 1 VR312
Angle Threaded Crimp Fitting x 1 VR306
Angle Tension Receiver x 1 VR305
*Component quantities per Bundle
Steel Inside Post Washer x 1 VR315
Angle Insert Sleeve x 1 VR335
Steel Inside Post Angle Insert Sleeve x 1 VR333
Steel Inside Post Washer Cable Stop
BY
Steel Inside Post Angle Insert Sleeve
Angle Insert Sleeve Angle Threaded Crimp Fitting
Post
CRIMP FIRST
Angle Washer x 1 VR345
Angle Tension Receiver Angle Washer
Post
CRIMP LAST
INSTALLATION INSTRUCTIONS *Fittings require 1/2 inch holes. 1. Slide the Steel Inside Post Angle Insert Sleeve, Steel Inside Post Washer, and Cable Stop onto the cable. Slide the Cable Stop until the cable is flush with the end of it. Double crimp the Cable Stop onto the cable. (See Diagram 1) 2. Insert the Cable Stop into the post and tap the Steel Inside Post Washer through the hole. Once the Steel Inside Post Washer is inside the post, push the cable into the post then pull it tight until the washer lies flat against the inside of the post. Insert the Sleeve with tongue on top if angle is up, bottom is angle is down. 3. Thread the cable through posts, making sure to put Insert Sleeves on the cable as you go. (Double check that the Insert Sleeves are facing the correct direction). 4. Hold the cable up to the side of the end post, pull the cable taut, mark and cut the cable 1 1/2" from the outside edge of the post. Be sure the Cable Stop and the Steel Inside Post Washer are seated into the post hole properly. (See Diagram 2).
POST
1 2 3 Each crimped fitting should be crimped twice (as shown). Check crimper dies occasionally to ensure that it is creating a secure, hexagonal crimp. CUT HERE
CABLE
DIAGRAM 1
5. Slide the cable into the Angle Threaded Crimp Fitting until the cable is flush with the threads. Double crimp the Angle Threaded Crimp Fitting onto the cable (See Diagram 1). POST
3 3
8. Use the supplied tightening tool to hold Threaded Crimp Fittings from rotating. Turn the Tension Receiver with the supplied Allen Wrench. Tighten the center cable first, then alternate (one higher, one lower) until all cables are tightened.
CABLE
9. Tap Insert Sleeves into the posts to finish installation. 10. Thoroughly clean the cables and all fittings. Trace amounts of iron may be on your stainless steel from tools and handling. The trace iron can rust or discolor your Viewrail installation. [continued on reverse side]
2 2
7. Repeat steps 1–6 for all cables.
1 1
6. Slide Angle Washer onto the Angle Tension Receiver, then insert the Angle Tension Receiver into the post and tighten onto the Angle Threaded Crimp Fitting by hand.
CUT HERE DIAGRAM 2
STAI
Steel Inside Post Angle Fitting Bundle – VR225
BY
[continued]
Angle Tension Receiver
Angle Washer Angle Insert Sleeve
Steel Inside Post Angle Insert Sleeve
Cable Stop
Steel Inside Post Washer
STAI
Standard Level Fitting Bundle – VR202
Fixed End Fitting x 1 VR308
Threaded Crimp Fitting x 1 VR302
BY
Tension Receiver x 1 VR301
Insert Sleeve x 2 VR330
*Component quantities per Bundle
Fixed End Fitting
Insert Sleeve
Insert Sleeve
Threaded Crimp Fitting
Post
CRIMP FIRST
Tension Receiver
Post
CRIMP LAST
INSTALLATION INSTRUCTIONS *Fittings require 1/2 inch holes. 1. Slide the cable into the Fixed End Fitting until the cable is flush with the end of the Fixed End Fitting. Double crimp the Fixed End Fitting onto the cable. (See Diagram 1) 2. Thread the cable through posts, making sure to put Insert Sleeves on the cable as you go. (Double check that the Insert Sleeves are facing the correct direction). 3. Hold the cable up to the side of the end post, pull the cable taut, mark and cut the cable 1 1/2" from the outside edge of the post. Be sure that the Fixed End Fitting is seated into the post hole properly. (See Diagram 2). 4. Slide the cable into the Threaded Crimp Fitting until the cable is flush with the threads. Double crimp the Threaded Crimp Fitting onto the cable (See Diagram 1).
POST
1 2 3 Each crimped fitting should be crimped twice (as shown). Check crimper dies occasionally to ensure that it is creating a secure, hexagonal crimp. CUT HERE
CABLE
DIAGRAM 1
5. Insert the Tension Receiver into the post and tighten it onto the Threaded Crimp Fitting by hand. POST
2 2
3 3
7. Use the supplied tightening tool to hold Threaded Crimp Fittings from rotating. Turn the Tension Receiver with the supplied Allen Wrench. Tighten the center cable first, then alternate (one higher, one lower) until all cables have been tightened.
1 1
6. Repeat steps 1-5 for all cables.
CABLE
8. Tap Insert Sleeves into the posts to finish installation. 9. Thoroughly clean the cables and all fittings. Trace amounts of iron may be on your stainless steel from tools and handling. The trace iron can rust or discolor your Viewrail installation.
CUT HERE DIAGRAM 2
STAI