Quick Start Guide - Clic - English

Quick start guide CLIC Series Cรณdigo: DYD-M003

Versiรณn: 0

Fecha: 27.09.17

Thank you for purchasing a Comfort Flex unit. Your new equipment was designed and manufactured with high quality components under strict manufacturing processes that guarantee the quality of the product at all times. We hope your Comfort Flex equipment will give you many years of comfort and energy savings without interruption.

We take this opportunity to remind you that your Comfort Flex unit warranty applies only for 12 months after the start of the equipment or 18 months after the invoice is issued. Wichever comes first.

Your comments and suggestions are important to us as they help us provide the best service in the industry. Please take a moment to register your equipment and fill out the Customer Satisfaction form.

If you have any questions or problems please contact our customer service department: USA Toll Free 1 800 201 48 16 LADA Sin Costo - México 01 800 890 59 17 www.comfort-flex.com

IMPORTANT Download Your full User Manual!

This document is a brief Quick Start Guide. Please download the complete user manual in PDF format from www.clima-flex.com/manuales/CLIC-ACCENG.pdf or scan the QR code.

Código: DYD-M003

Versión: 0

Fecha: 27.09.17

QUICK START GUIDE

CONTENTS DIMENSIONAL DATA............................................................................. 2 PRINCIPAL COMPONENTS.................................................................... 4 INSTALLATION REQUIREMENTS............................................................. 5 ABOUT LOCATION................................................................................. 5 ABOUT LIFTING...................................................................................... 6 ABOUT WATER CONNECTION.............................................................. 6 ABOUT ELECTRIC CONNECTION.......................................................... 7 GENERAL WARNINGS........................................................................... 7 ABOUT PIPING....................................................................................... 8 ABOUT MAIN SCREEN........................................................................... 9 ABOUT USER INTERFACE....................................................................... 9 ABOUT THE MENU.................................................................................. 10 ABOUT THE STARTUP.............................................................................. 11 ABOUT THE PHYSICAL INSPECTION...................................................... 12 ABOUT THE HYDRAULIC CIRCUIT.......................................................... 12 ABOUT THE ELECTRICAL INSPECTION.................................................. 13 ABOUT THE CONTROL PANEL................................................................ 14 STARTUP.................................................................................................. 14 COMPRESSORS...................................................................................... 14 ABOUT THE MAINTENANCE PROGRAM............................................... 15 ABOUT TROUBLESHOOTING.................................................................. 18 ALARMS - POSSIBLE CAUSES................................................................ 20 ABOUT THE WARRANTY......................................................................... 24 REFERENCE DATA.................................................................................. 25

Cรณdigo: DYD-M003

Versiรณn: 0

Fecha: 27.09.17

1

QUICK START GUIDE

DIMENSIONAL DATA

W

L2

L1

TOP VIEW

FRONT VIEW

D

H

4" VITAULIC OUTLET

SIDE VIEW

ISOMETRIC VIEW

4" VITAULIC INLET

W

83 1/4"

32 1/4"

86 3/4"

10 1/2"

72 3/4"

H

L1

D

L2

Fecha: 27.09.17

Versiรณn: 0

Cรณdigo: DYD-M003

2

Cรณdigo: DYD-M003

Versiรณn: 0

L1

L2

W

D

FRONT VIEW

TOP VIEW

Fecha: 27.09.17 4" VITAULIC OUTLET

H

SIDE VIEW

4" VITAULIC INLET

83 1/4" 72 3/4" 10 1/2"

H L2

D L1

86 3/4" 64 1/2"

W

ISOMETRIC VIEW

QUICK START GUIDE

DIMENSIONAL DATA

3

QUICK START GUIDE

PRINCIPAL COMPONENTS

4

Cรณdigo: DYD-M003

Versiรณn: 0

Fecha: 27.09.17

QUICK START GUIDE

INSTALLATION REQUIREMENTS ABOUT LOCATION

The unit must be installed on a solid, perfectly level base. For earthing purposes, a solid cement base, that is wider than the unit, must be made. This base must be able to support the weight of the unit. Anti-vibration supports must be installed between the frame of the unit and the cement base of the steel beams; for such installation follow the dimensional drawing supplied with the unit. The frame of the unit must be perfectly levelled during installation, if necessary using shims to be inserted under the the anti-vibration supports.

Maintenance Area

Vertical Air Discharge

Vertical Air Discharge

D

Vertical Air Discharge

Vertical Air Discharge

Surrounding Wall

Air Flow

B

Maintenance Area

Air Flow

C

F

E Maintenance Area

Maintenance Area

A

B

A

Recommended unit clearences

DIMENSIONS A

B

C in

D

in

cm

in

cm

cm

in

32¼

82

40

102 86¾ 221 15¾

E

F

cm

in

cm

40

19¾

50

in

cm

78¾ 200

If the unit is installed in places that are easily accessible to people and animals, we recommend that protection grates be fitted all round to prevent access. To ensure optimal performance in installation site, the following precautions and instructions must be respected:

Código: DYD-M003

Versión: 0

• Make sure that there is a strong,

solid foundation to reduce noise and vibrations.

• Avoid installing the unit in areas that could be dangerous during maintenance operations, such as platforms without handrails, guide rails or in areas that fail to comply with requirements as regards free space around the unit.

• The installer is responsible for calculating the best position for the unit.

It is vital that all minimum distances for all units are complied with to ensure there is adequate ventilation for the condenser racks.

When deciding where to position the unit and to ensure proper airflow, the following factors must be taken into consideration: • Avoid the recirculation of hot air • Avoid insufficient air supply for the air cooling condenser. Both these conditions can cause an increase in condenser pressure which can lead to poor energy efficiency and refrigerating capacity.

The noise generated by the unit is mainly due to the rotation of compressors.

The noise level for each model size is listed in the documentation.

If the unit is correctly installed, operated and maintained, noise emission levels do not require any special protective devices to operate continuously close to the unit without any risk.

In case of installation with special noise requirements it may be necessary to install additional noise softening devices.

Fecha: 27.09.17

5

QUICK START GUIDE

200 cm

200 cm

78¾

78¾

WARNING

ABOUT LIFTING When transporting the unit, it is recommendable to use a forklift to lift it. All units have lifting points.

Only these points may be used for lifting the unit, as shown in the following figure.

ABOUT WATER CONNECTION The units have a water input and output for the connection of the chiller to water circuit of the system.

When lifting the unit, please keep the unit stable and without tilting.

This circuit must be connected to the unit by an authorized technician and must comply with all the current national and local regulations on the subject.

The components listed below are not included with the unit, but are supplied upon request, also if their installation is compulsory.

If dirt penetrates the water circuit, there could be problems. Therefore always remember the following when connecting the water circuit: 1. Only use pipes that are clean inside.

2. Keep the end of the pipe facing downward when removing any burrs.

3. Cover the end of the pipe when inserting it through a wall to avoid dust and dirt getting in 4. Clean the pipes of the system located between the filter and the unit, with running water, before connecting it to the system.

Equipment

Capacity

# Modules

GPM

φ Vitaulic

CDP ft w.g. (Mother)

M

25

1

60

4

16.01

Val. Reg. Val. Sec CPD Tub+Acc CPD Total 6.93

0.47

0.05

M+S

50

2

120

4

16.01

6.93

0.47

0.36

24.96

M+(S*2)

75

3

180

4

16.01

6.93

0.47

1.16

25.80

M+(S*3)

100

4

240

4

16.01

6.93

0.47

2.64

27.36

M+(S*4)

125

5

300

4

16.01

6.93

0.47

5.04

29.88

M+(S*5)

150

6

360

4

16.01

6.93

0.47

8.56

33.58

M+(S*6)

175

7

420

6

16.01

6.93

0.47

2.39

27.09

M+(S*7)

200

8

480

6

16.01

6.93

0.47

3.50

28.26

M+(S*8)

225

9

540

6

16.01

6.93

0.47

4.93

29.76

M+(S*9)

250

10

600

6

16.01

6.93

0.47

6.69

31.61

Revision of pipe diameter according to equipment gallonage.

6

Código: DYD-M003

Versión: 0

Fecha: 27.09.17

24.63

QUICK START GUIDE

ABOUT ELECTRIC CONNECTION • All field wiring must be installed

in accordance with the national wiring regulation.

• All the terminals and connections must be tightened. Improper connection and fastenings could cause electric shock, short circuit and fire.

• Ensure that the rated voltage of the unit corresponds to that of the name plate before commencing wiring work according to the wiring diagram.

• The unit must be GROUNDED to prevent possible hazards due to insulation failure.

• All electrical wiring must not touch the refrigerant piping, compressor, pump, fan motor or any moving parts of the fan motors.

GENERAL WARNINGS • Do not operate the chiller with

wet hands. It could result in electric shock.

• Do not use fuse of different amperage than stated. Using wire etc. to replace a fuse could cause equipment damage or fire.

• Do not allow water to remain in the water pipes if the unit is not operating for a long period.

• Water must be drained out if the unit is not running during winter.

Failing to do so would cause the pipe to freeze and crack.

• Do not drink the chilled water of the unit.

Example of Single point connection

Example of Multiple point connection Código: DYD-M003

Versión: 0

Fecha: 27.09.17

7

QUICK START GUIDE

ABOUT PIPING

1. Flex connections 2. Temperature gauge 3. Pressure gauge 4. Y strainer 5. Isolation valve 6. Air separator and vent

NOTE

TYPICAL PIPING

This diagrams are not intended to be a design and is given only as an idea of a typical installation of a chiller . The manufacturer assumes no responsibility for any omission in this drawing.

Fecha: 27.09.17

Versiรณn: 0

Cรณdigo: DYD-M003

8

QUICK START GUIDE

ABOUT MAIN SCREEN The configured devices will show this screen by default as the initial screen of the system. It shows the following information: 1

6

2

ABOUT USER INTERFACE • Navigation Bar The navigation bar is found on every screen of the system. The bar hides and unhides automatic by pressing the tab at the bottom as shown in Fig. 9. When the tab is pressed the navigation menu is displayed.

3

4

Fig. 9 - Navigation bar displays the tab.

Example of navigation bar in the main screen.

5

• Icons

1. System Work mode icon, either in

“Tandem Mode” or standalone mode.

2. Head unit injection and return temperature if the system is in “Tandem Mode” or injection and return temperature of the mother unit if the system is in standalone mode.

3. Injection and return temperatures of the individual units. This section only appears if at least one “Son” unit is enabled. In the case of standalone machines this section is not shown.

4. Control State, It can be on, off by digital input or off by the terminal (pGDTouch).

5. Temperature metric selection (farenheit or celcius) .

6. Date In the navigation menu of the initial screen, the icons displayed in order from left to right lead to the following sections:

Alarms

Always visible, sends the user to the Alarms Page.

Home

Always visible, sends the user to the Home Page

Return

Sends the user to the last screen accessed

Main Menu

Sends the user to the Main Menu

Alarm Log

Sends the user to the Alarm Logs screen

Inputs / Outputs

Sends the user to the Inputs & Outputs screen

Graphics

Sends the user to the Temperature Graphs screen

Graphics Config

Allows the user to configure the Graphics Display

Summary

Sends the user to the Summary screen

• Temperature Graphics • Alarms • System Overview • Navigation Menu Código: DYD-M003

Versión: 0

Fecha: 27.09.17

9

QUICK START GUIDE

ABOUT THE MENU On the home screen is the access button to the navigation menu.

This menu contains the navigation pages that contain all system parameters. It is divided into four sections: open access, access Level 1, Level 2 and Level 3.

Open / Access Navigation

Navigation Menu - Level 1

Navigation Menu - Level 2

Navigation Menu - Level 3 Note: If you need more info about this MENU, please download the FULL User Manual 10

Cรณdigo: DYD-M003

Versiรณn: 0

Fecha: 27.09.17

QUICK START GUIDE

ABOUT THE STARTUP The following items must be checked before the unit’s startup Date: Jobsite: Location: Installer Contractor: Technician / Company: Starting the unit:

Unit model: Unit serial number:

WARNING

The following procedures are to be considered by the installer; their personnel must be qualified, and certified to perform installation in order to comply all specifications and good practices to assure the correct unit´s operation.

Código: DYD-M003

Versión: 0

Fecha: 27.09.17

11

QUICK START GUIDE

ABOUT THE PHYSICAL INSPECTION

WARNING

The following procedures are to be considered by the installer; their personnel must be qualified, and certified to perform installation in order to comply all specifications and good practices to assure the correct unit´s operation.

• Checking unit for possible transportation or handling damage.

• Visually check for refrigerant leaks.

• Only open unit to install system piping. Do not remove connection’s protection. Until hydraulic circuit is to be closed.

• Check for foreign objects in fan discharge • Check that air intake is not obstructed and has the require space suggested on page 5.

ABOUT THE HYDRAULIC CIRCUIT The installation of a water filter is necessary on all hydraulic circuits in order to avoid solid particles in it, which must be installed on the return side of the circuit, and cleaned once the system´s initial charge is finished.

• Check water filter to be clean.

• Verify that all service valves are open.

• Check for adequate makeup of the water supply.

• Verify that all piping is water full and air has been vented out.

• Check thermometers.

• Check manometers

12

Código: DYD-M003

Versión: 0

Fecha: 27.09.17

QUICK START GUIDE

ABOUT THE ELECTRICAL INSPECTION The unit require 3 phase grounded electrical power.

• Verify that the thermo-magnetic switch is of correct capacity for the unit.

• Check that all the electrical connections are tight.

• Check for false contacts on ground, and all wiring.

• Check internal connections for control and power.

• Measure voltages on all lines, and ground, neutral and trifasic line.

• Check for overload protection on motors to be in position to design requirements and on automatic mode.

• Check voltage monitor control (*MotorSaver) , to be adjusted to supply the correct power voltage for the unit

*The unbalance percentage of electrical supply should be calculated with the following formula and adjusted on the UNBALANCE TRIP knob.

Unbalance porcentage = [(Maximum average deviation)/(average)] X 100

DIAGNOSIS INDICATING LIGHTS (LED STATUS) NORMAL OPERATION CONSTANT GREEN START DELAY INTEMITENT GREEN INVERTED PHASE INTERMITENT RED PHASE UNBALANCED RED ON LAPSES HIGH/ LOW VOLTAGE CONSTANT RED

NOTE

Units are previously factory adjusted according to plates however the electrical supply may vary on each installation, and due to this unbalance must be adjusted before startup in order to protect all the unit´s motors and electrical components.

Código: DYD-M003

Versión: 0

Fecha: 27.09.17

13

QUICK START GUIDE

ABOUT THE CONTROL PANEL

NOTE

Units are previously factory adjusted according to models however the electrical supply may vary on each installation, and due to this unbalance must be adjusted before startup in order to protect all the unit´s motors and electrical components.

• Check the control panel to ensure that it is free of foreign objects.

• Energize the unit with 3 phase electrical power.

• Phase unbalance must less than 2% of average.

• Cycle each fan to assure rotation is correct.

• Cycle water pump (if applicable) to ensure that it is correctly energized.

After finishing the inspection of the previous installation points and making sure all the unit’s items are correct the unit may be started.

STARTUP It is recommended to energize 24 hrs. Before start-up for preheating of compressor housing NOTE

After energizing the controller, wait five minutes for the unit to be on line and ready.

Operation sequence will initiate by checking all security pre-programed points on the unit. If all required conditions are OK the unit will be ready to initiate operation.

Unit Control

To start operation set the ON/OFF switch to the ON position.

After six seconds the controller will command the start of the water pump.

If water flow is detected on the pipes, the internal sequence of the unit will begin.

On / Off

COMPRESSORS 24V

Set the APG1 switch, 24V to the ON position afterwards set the APG2 switch also to the ON position, this will enable the compressors start cycle.

14

Código: DYD-M003

Versión: 0

COMPRESOR

RESET

Fecha: 27.09.17

QUICK START GUIDE

ABOUT THE MAINTENANCE PROGRAM Before intervening this unit make sure you have your complete personal safety equipment, and that the unit is without power and totally at rest. It is recommended to energize your unit 24 hours before the first start up to begin heating the compressor crankcase.

1.1 HYDRAULIC MAINTENANCE Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec

Plan

x

x

x

x

x

x

x

x

x

x

x

x

x

x

x

x

x

x

x

x

x

x

x

x

x

x

x

x

x

x

x

x

x

x

x

x

Filter cleaning hydronic circuit, if exist.

Real

Visual inspection of all water pipes for leak detection.

Water repacement in the hydronic circuit.

Plan

Real

Plan

Real

It is recommended to do a daily visual inspection of your equipment, to perform preventive and non-corrective procedures during the monthly maintenance check.

NOTE

Cรณdigo: DYD-M003

Versiรณn: 0

Fecha: 27.09.17

15

QUICK START GUIDE

ABOUT THE MAINTENANCE PROGRAM 1.2 ELECTRICAL MAINTENANCE Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec Retightening of connectors and terminals in the electrical panel, control part, power and junction boxes.

(Quarterly) Physical inspection of all contactors and relays on the electrical panel. (Monthly) Check amperage of all electric motors and compare according to equipment nameplate for detect abnormalities.

(Quarterly) Physically verify false contacts.

(Monthly) Check the adjusting and state of the electrical protections and fuses, these must be under the manufacturer's specifications.

(Monthly) Electrical panel cleaning (Monthly) 16

Plan

x

x

x

x

Real

Plan

x

x

x

x

x

x

x

x

x

x

x

x

Real

Plan

x

x

x

x

Real

Plan

x

x

x

x

x

x

x

x

x

x

x

x

x

x

x

x

x

x

x

x

x

x

x

x

x

x

x

x

x

x

x

x

x

x

x

x

Real Plan

Real

Plan Real

Cรณdigo: DYD-M003

Versiรณn: 0

Fecha: 27.09.17

QUICK START GUIDE

ABOUT THE MAINTENANCE PROGRAM 1.3 PHYSICAL INSPECTION Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec Condenser cleaning with pressurized water (Bimonthly) Check refrigerant pressures (Quarterly) Fan blades inspection, blades must be clean (Quarterly) Check power consumption of compressors to determine refrigerant losses (Quarterly) Compressor oil inspection (Monthly) Equipment's internal inspection and cleaning (Bimensual) Condensate drain line inspection, must be unobstructed (Bimensual) Reviewing alarm logs (Monthly)

Plan

x

x

x

x

x

x

Real Plan

x

x

x

x

x

x

x

x

x

x

x

x

Real Plan Real

Plan

Real Plan

x

x

x

x

x

x

x

x

x

x

x

x

Real Plan

x

x

x

x

x

x

x

x

x

x

x

x

Real

Plan

Real Plan

x

x

x

x

x

x

x

x

x

x

x

x

Real

Cรณdigo: DYD-M003

Versiรณn: 0

Fecha: 27.09.17

17

QUICK START GUIDE

ABOUT TROUBLESHOOTING PROBLEM

Compressor will not run

Compressor will not stage up.

18

Cรณdigo: DYD-M003

POSSIBLE CAUSES

POSSIBLE CORRECTIVE STEPS

Main or compressor disconnect switch open.

Close switch.

Fuse blown. Circuit breakers open.

Check electrical circuits and motor windings for shorts or grounds. Investigate for possible overloading.

Check for loose or corroded connections. Replace fuse o reset breakers after fault cause is corrected.

Thermal overloads tripped.

Overloads are auto-reset.

Check voltages, cycle times and mechanical operations.

Allow time for auto-reset.

Defective contactor or coil.

Replace.

System shutdowm by equipment protection devices.

Determine type and cause of shutdown and correct it before restarting equipment.

No cooling required.

None. Wait until unit calls for cooling.

Liquid line solenoid will not open.

Repair or replace solenoid.

Check wiring.

Motor electrical trouble.

Check motor for opens, shorts or burnout.

Humidity in the compressor.

Replace compressor.

Loose wiring.

Check all wire junctions.

Tighten all terminal screws.

Defective capacity control.

Replace.

Faulty sensor or wiring.

Replace.

Stages not set for application.

Adjust controller setting for application.

Versiรณn: 0

Fecha: 27.09.17

QUICK START GUIDE

ABOUT TROUBLESHOOTING PROBLEM

Compressor noisy or vibrating

High discharge pressure

Cรณdigo: DYD-M003

POSSIBLE CAUSES

POSSIBLE CORRECTIVE STEPS

Low lift, inverted start.

Control issues.

Compressor running in reverse.

Check unit and compressor for correct phasing.

Improper pipingor or support on sucction or discharge.

Relocate, add, or remove hangers.

Worn compressor isolator bushing.

Replace.

Compressor mechanical failure.

Replace.

Noncondensables in system.

Extract noncondensables with approved procedures or replace charge.

Circuit overcharged with refrigerant.

Remove excess,check liquid subcooling.

Optional discharge shutoff valve not open.

Open valve.

Condenser fan control wiring not correct.

Correct wiring.

Fan not running.

Check electrical circuit and fan motor.

Dirty condenser coil.

Clean coil.

Air recirculation.

Correct.

Versiรณn: 0

Fecha: 27.09.17

19

QUICK START GUIDE

ALARMS - POSSIBLE CAUSES The alarms that may occur, depending on the initial configuration are: • Sensor Failures Alarms: If a sensor is detected as disconnected or broken, the algorithm which is used will be disabled. If the sensor is the head injection sensor, the units will work in standalone mode automatically • Phase Failure Alarm: activated by a digital input. The MotorSaver alarm is a high priority situation and stops all machine functions. It is manually reset.

• No Flow Alarm: The No Flow Alarm is a high priority alarm and must be manually reset. This alarm stops all machine functions.

• Freezing Alarm: If the freezing temperature sensor is below a programmed threshold, the freeze alarm is triggered. This condition stops all functions of the equipment in question. This alarm is automatically restored when the temperature exceeds a value of restitution and keeping the unit in reset mode (no power to operate) for the scheduled time.

• Freezing Water Alarm: Same case as the freezing alarm, but in this alarm the reading from the injection sensor is considered.

• High Pressure Alarm: It is activated through a digital input. This alarm is a high priority event and stops compressor operation; but it does not stop the pump. It is a manually reset alarm. If the unit is cooled by air a command is sent to start the fan of the condenser unit. To restore keep the unit in high return, the compressor will not start until the scheduled time has elapsed.

• Low Pressure Alarm: It is activated through a digital input. This alarm stops the compressor of the unit in question. It is automatically restored but keeps the unit in a low return mode.

• Disconnection Alarm: If the system was setup with any “Son” units and any of these units disconnects this alarm will be trigged.

• Condenser High Temperature Alarm: This alarm is enabled only when the unit is air-cooled. The alarm is activated when the reading from the condenser temperature sensor exceeds its limit. No control action is taken.

• Condensate Flow Alarm: the condensate flow alarm functions like the main flow alarm; the alarm routine is activated only when the system is cooled by water.

• Lack of Refrigerant Alarm: this alarm is activated when a start command is sent because of cooling demand, and after a while no temperature change is detected in the injection temperature sensor. This alarm takes no action control and can be disabled by the user.

20

Código: DYD-M003

Versión: 0

Fecha: 27.09.17

QUICK START GUIDE

ABOUT TROUBLESHOOTING PROBLEM

Low suction pressure

Compressor thermal protection switch open

Cรณdigo: DYD-M003

POSSIBLE CAUSES

POSSIBLE CORRECTIVE STEPS

Rapid load swings.

Stabilize load.

Lack of refrigerant.

Check for leaks, repair, add charge. Check liquid sight glass.

Fouled liquid line filter drier.

Check pressure drop across filter drier. Replace.

Expansion valve malfunctioning.

Repair or replace and adjust for proper superheat.

Condensing temperature too low.

Check means for regulating condenser temperature.

Compressors not staging properly.

See corrective stepsCompressor staging intervals too low.

Insufficient water flow.

Correct flow.

Excess or wrong oil used.

Recover or change oil.

Evaporator dirty.

Back flush or clean chemically.

Operating beyond design conditions.

Correct so conditions are within allowable limits.

Discharge valve not open.

Open valve.

Short cycling.

Stabilize load or correct control settings for application.

Voltage range or imbalance.

Check and correct.

High superheat.

Adjust to correct superheat.

Compressor mechanical failure.

Replace compressor.

Versiรณn: 0

Fecha: 27.09.17

21

QUICK START GUIDE

ABOUT TROUBLESHOOTING PROBLEM

Compressor oil level too high or too low

Motor Overload Relays or Circuit Breakers Open

22

Cรณdigo: DYD-M003

POSSIBLE CAUSES

POSSIBLE CORRECTIVE STEPS

Oil hang-up in remote piping.

Review refrigerant piping and correct.

Low oil level.

Verify superheat, add oil.

Loose fitting on oil line.

Repair.

Level too high with compressor operating.

Confirm correct superheat, remove oil.

Insufficient water flowLevel too high.

Correct flow, verify superheat.

Excessive liquid in crankcase- Level too high.

Check crankcase heater.

Check liquid line solenoid valve operation.

Short cycling.

Stabilize load or correct control settings for application.

Expansion valve operation or selction.

Confirm superheat at minimum and maximum load conditions.

Compressor mechanical issues.

Replace compressor.

Wrong oil for application.

Verify.

Voltage imbalance or out of range.

Correct power supply.

Defective or grounded wiring in motor.

Replace compressor.

Loose power wiring or burnt contactors.

Check all connections and tighten, replace contactors.

High condenser temperature.

See corrective steps for High Discharge Pressure.

Versiรณn: 0

Fecha: 27.09.17

QUICK START GUIDE

ABOUT TROUBLESHOOTING PROBLEM

Equipment does not start.

Equipment starts but it is not cooling enough.

Fans do not operate.

Fan motor is protected.

Water pump does not start.

Cรณdigo: DYD-M003

POSSIBLE CAUSES

POSSIBLE CORRECTIVE STEPS

Improper voltage.

Check the voltage and correct it.

No water flow in the system.

Drain the system.

Water flow is reversed.

Check flow direction.

Incorrect setting of temperature value.

Set temperature.

Dirty condenser.

Clean the condenser.

Air suction and discharge clogged.

Remove all possible obstacles.

Insufficient refrigerant in the system.

Contact the manufacturer.

Check the system for leaks.

Insufficient water flow in the system.

Check the pumping system.

The water in the system is dirty or contaminated.

Drain dirty or contaminated water and replace it with clean water.

No power.

Check the electrical connection. (False contact)

Defective motor.

Contact the manufacturer.

Wrong electrical circuit.

Check the circuit and repair as necessary.

Overheated starter relay.

Contact the manufacturer.

No power.

Check the electrical connection.

Pump with possible defect.

Check the water pump or replace if necessary.

Versiรณn: 0

Fecha: 27.09.17

23

QUICK START GUIDE

ABOUT THE WARRANTY This warranty applies only for products marketed by the manufacturer and its national dealers. The manufacturer guarantees the operation of this equipment, besides the labor employed in the manufacture thereof, for the period according to the attached table, against any manufacturing defect from the date of delivery of the product, under the following: TERMS AND CONDITIONS

• Warranty service can only be carried out by an Authorized Service

Center, as long as the manufacturer products have been traded by the manufacturer and it’s authorized Mexico distributors. The address of the nearest Authorized Service Center can be consulted calling the following telephone number: 01 800 890 59 17 • To enforce this guarantee the fault or device status must be notified at 01 800 890 59 17, keep the number of the reporting service that will be provided when reporting the fault, besides the service report to validate that the equipment stopped operating due to a defect of the equipment components.

• During the term of this warranty, the manufacturer, through its Authorized Service Centers is committed to repair the equipment when the fault is attributable to a manufacturing error. In which case the manufacturer will be responsible for the delivery of the spare(s) and cover the cost of labor required.

• Spare parts and parts used to repair the appliance will have no cost to the customer, as long as the warranty period specified in this policy has not been completed.

• In the previous section manual labor is not included.

• This warranty does not cover damage or repairs required as a result of failures in the equipment installation or a wrong operation.

• This warranty applies only for 12 months after the start of the equipment or 18 months after the invoice is issued. Wichever comes first.

THIS WARRANTY NOT BE VALID IN THE FOLLOWING CASES

1. When the product had been used under conditions other than normal.

2. When the product has not been operated in accordance with the instructions for use included with the computer.

3. When the equipment has been altered, repaired or installed by unauthorized personal by the manufacturer.

In case of loss of this policy, the consumer can request a replacement to the place of purchase or to the manufacturer, with prior presentation of proof of purchase (invoice).

24

Código: DYD-M003

Versión: 0

Fecha: 27.09.17

QUICK START GUIDE

REFERENCE DATA Measure of Length 12

inches

=

1

foot

3

feet

=

1

yard

yards

=

1

rood

6

feet

=

1

fathom

40

roods

=

1

furlong

8

furlongs

=

1

mile

yards

=

1

mile degree

sea miles

=

1

degree

miles

=

1

sea mile

5½

1760 60 0.8684

Pressure Table PSI

Temperature Conversion Bares

Fahrenheit

60

4.1370

40°F

4.44°C

70

4.8265

41°F

5.00°C

80

5.5160

42°F

5.56°C

90

6.2055

43°F

6.11°C

100

6.8950

44°F

6.67°C

150

10.3425

45°F

7.22°C

200

13.7900

46°F

7.78°C

250

17.2375

47°F

8.33°C

300

20.6850

48°F

8.89°C

350

24.1325

49°F

9.44°C

400

27.5800

50°F

10.00°C

450

31.0275

51°F

10.56°C

500

34.4750

52°F

11.11°C

550

37.9225

53°F

11.67°C

600

41.3700

54°F

12.22°C

55°F

12.78°C

Linear Measure 1 inch

Celsius

= 2.54

56°F

13.33°C

cm

57°F

13.89°C

1 yard

= 0.914401

m

58°F

14.44°C

1 mile

= 1.609347

km

59°F

15.00°C

60°F

15.56°C

Código: DYD-M003

Versión: 0

Fecha: 27.09.17

25

/ComfortFlexMexico

/ComfortFlexMx

/Comfort-Flex

/ClimaFlex

Av. Central No. 285, Parque Logistico, Deleg. La Pila, San Luis Potosi, C.P. 78422 More Info (444) 161.50.43 info@clima-flex.com service@clima-flex.com US Toll Free 01 800 201 48 16 Lada sin costo 01 800 890 59 17 Cรณdigo: DYD-M003

Versiรณn: 0

Fecha: 27.09.17