KUIU Pack Manual

Page 1

PACK MANUAL



TABLE OF CONTENTS PACK ANATOMY......4-5 FITTING..........6-17 LOAD SLING......18-31 PACK CHANGE.....32­-37 ACCESSORIES.....38-39

ACCESS INSTRUCTIONAL VIDEOS AT WWW.KUIU.COM


Upper Frame Stay Pocket Load Sling Bridge Strap Frame Handle Shoulder Harness Shoulder Harness Webbing Lumbar Pad Hip Belt Hip Belt Buckle

4


PACK ANATOMY

Load Lifter Strap Hydration Tube Holder Side Compression Straps Sternum Strap

Load Stabilizer Strap Detachable Hip Belt Webbing

Hip Belt Profile Strap

Bottom Compression Straps

5


FITTING


FITTING 17”

Our packs are shipped with the shoulder harness adjusted to fit a 17” torso (19” on X-tall frames). Use this as a general guide and adjust the harness up or down for best fit.

7


Use the highlighted straps shown here to adjust the pack fit in the next seven steps. Before you get started, loosen all straps.

8


FITTING Step one, load the pack with 2030lbs in the main compartment. Note that in the PRO packs the weight can be secured with the installed webbing pictured above.

9


Step two, loosen all highlighted straps. Then lift the loaded pack by the frame handle and get into the suspension.

10


FITTING Top of hip bone

ensionlock Atiis eatiorum eumquae consequost et minto quis et odicab ipit a ditia doluptum int. Ipsa sant vit odiatia ped que sum re volo qui sus rem acest, iusdam quo Stepamthree, tighten the hip belt so eos ut pratus. that theeliberae top rests rightmilitatqui above the Bo. Itat magnis iliac crestquiatio (top ofnserspi hip bone). Idealtempostiam ducium ly 60+% of the pack weight should be supported by the hip belt.

11


12

Step four, attach the sternum strap and adjust it up or down until it is comfortable. This will align the harness properly on your body while you adjust the shoulder straps.


FITTING Step five, pull the shoulder harness webbing towards the lumbar pad to tighten the shoulder harness, taking weight off your hips.

13


350 to 450

14

Step six, tighten the load lifter straps evenly. Do not over-tighten. The ideal load lifter angle to relieve pressure on the top of your shoulders is 350 to 450.


FITTING Step seven, tighten your load stabilizer straps evenly to pull the pack bag securely to the hip belt.

15


Load Lifter base should be here

The load lifters should meet the shoulder harness at a point between your collar bone and the top of your shoulder.

16


FITTING

No gaps from here to here

T-Locks are located on the back of the harness here

To eliminate gaps and properly position the load lifter attachment point, adjust the shoulder harness up or down as pictured on page 7. Make sure the T-locks are engaged and evenly positioned on the frame.

17


LOAD SLING


LOAD SLING

Load Lifter Buckle

Step one, unclip the load lifter straps from the pack bag.

19


Step two, unclip and loosen all four side compression straps.

20


Bottom Compression Straps

LOAD SLING

Metal Hook

Step three, disengage the metal hip belt hook connecting the hip belt and bag, then loosen the bottom compression straps.

21


Lower Bag Attachment Strap

Load Stabilizer Strap

Step four, loosen the lower bag attachment straps. Then loosen the load stabilizer straps.

22


LOAD SLING Step five, slide the frame down and out of the upper stay pockets.

23


Bridge strap

Step six, unclip the bridge straps located at the top of frame stays.

24


LOAD SLING Step seven, lay the pack and frame face down. Place contents into the sling between the frame and bag. We recommend using a game bag or dry bag to carry gear or meat in the load sling.

25


Step eight, attach the male bridge strap buckles to the pack bag female buckles.

26


LOAD SLING Step nine, tighten the bridge straps so the pack bag is pulled upward and close to the upper frame stays.

27


Bottom Compression Straps Lower Bag Attachment Straps

28

Step ten, evenly tighten the lower bag attachment straps to compress the bottom of the bag towards the hip belt. Then tighten the bottom compression straps.


LOAD SLING Step eleven, attach and securely tighten the four side compression straps.

29


Bridge Strap Load Lifter

Step twelve, stand the bag upright and attach the load lifter male buckle to the bridge strap female buckle.

30


LOAD SLING Step thirteen, tighten the load stabilizer straps after getting the bag on your back and tightening the hip belt. A slight V shape should be formed between the bag and frame to keep meat or gear from sliding down.

31


PACK CHANGE


PACK CHANGE

Step one, unclip the load lifter straps from the pack bag.

33


Step two, unclip all four side compression straps and load stabilizer straps.

34


PACK CHANGE

Step three, unclip the metal hook and bottom compression straps, then loosen and unclip the lower bag attachment straps.

35


Step four, slide the frame down and out of the upper stay pockets.

36


To attach the new bag, reverse steps from page 33 to page 37.

PACK CHANGE

The bag should now freely disengage from the frame.

37


ACCESSORIES Pro Hip Belt Pouch

Slide mesh sleeve over the entire hip belt

38

Install the PRO hip belt pouches by sliding the entire hip belt through the mesh sleeve on the back of the pouch. The pouch should rest over the belt as shown above.


ACCESSORIES

Barrel Strap

Stock Cradle KUIU pack bags have upper and lower webbing loops for installation of gun and bow holders. These can be installed on either the back or side of the pack bag. Side installation is pictured here.

39


KUIU.COM

1920 N. LINCOLN ST. SUITE 101 DIXON, CA 95620 855.367.5848


Turn static files into dynamic content formats.

Create a flipbook
Issuu converts static files into: digital portfolios, online yearbooks, online catalogs, digital photo albums and more. Sign up and create your flipbook.