Data Powertools / Carbitool Routing Catalogue by Data Powertools Ltd

c Car di f fBr anc h

Br i dgendBr anc h

CONTENTS SAFETY TIPS & HELPFUL HINTS Conversion Table 1. Always keep collet clean. Replace when worn. inches mm 80% of all tool breakage is directly traced to worn ‘ovalized’ collets. Resolve breakage by changing to a new collet. 2. Insert shank 19mm (3/4”) into collet. Holding only the upper edge of the shank by the lower portion of the collet will inevitably lead to Router Bit breakage, spindle nose wear, and collet bell-mouthing. 3. Tighten the collet securely. 4. Store your bits in a Plastic Pouch. Do not let them lay loose in your tool box. 5. Clean Ball Bearings with solvent, then submerge them in thin oil lubricant. 6. Have your tools serviced by a professional service shop. A properly sharpened tool is vital to the success, quality and profitability of your operation. Remove the tool for servicing whenever poor job finish or increased feed pressure indicates a dull cutting edge. Also remove the tool for servicing at the slightest sign of a chip or nick in the cutting edge. 7. We recommend the use of 12.7mm (1/2”) diameter shanks where possible for more stability and less chatter. 8. Router Bits over 38mm (1-1/2”) in diameter should be used in bench mounted or overhead router machines. 9. When using bits larger than 50mm (2”) diameter, care should be taken to ensure that speeds, feed rate and number of passes are appropriate for the diameter of bit used. Consult your routing machine supplier for further advice. CUTTING SPEED IN R.P.M

UP TO 25mm 26mm-50mm 51mm-63mm 64mm-75mm 76mm-87mm

WOOD 24 18 16 14 12

000 000 000 000 000

Premium Quality Router Bits Page

4 - 39

Page

Aluminium

Edge Band Trim Bits

Cutting Bits 34 Arbors 33 Batten Mould Bits 23 Beading/Ovol Bits 14,15,17,18 Bearings 20, 33 Bevel Trim Bits 8,9,10 Bull Nose Bits 21

Edge and Draw Face Bits

Face Moulding Bits (architrave, sills, etc) 25,26

Fibreglass Bits Finger Joint Bits Flush Trim Bits

34 27 6,8,9

Groove Forming Bits 11,12 21 21 Chamfering Bits 20 Handrail Bits Hinge Mortice Bits 6 Classical Bits 14,16,18,19 Hook Slot Bits 11 Combination 28 Trim Bits 8,9,10 Jointing Bits Combination Kits 5 Multi-Form Bits 16 Laminate Trim Bits Compression Bits 34 6,8,9,10 Core Box Bits 13 Mitre lock Bits 28 Cove Bits 18 Mortise Bits 6 Corian(solid surface) 23,24 Multi Form 16 Dish Cut Bits 15 Ogee Bits 13,14,18,22 Double Edge Radius Bits 23 Ovolo/Bearings Dovetail Bits 11 14,15,17,18 Draw Pull Bits 11 Palace Pattern Bits 16 Draw Joint Bits 28 Panel Door Bits 29,30 Drawing Line Bits 21 Pilot Panel Bits 6 Canoe Slat Bits

Page

10 Plastic Cutting Bits

Provincial Bits Raised Panel Bits Rebating Bits Regency Bits Reed Bits Replaceable Tip Bits Roman Ogee Bits Rounding Over Bits Slot Mortise Bits Slotting Cutters Solid Surface Bits Straight Bits

Tongue and Groove Bits Toy Wheel Cutters T-Slot Bits

28 35 12

Vee Groove Bits Veining Bits

000 000 000 000 000

and Rail Bits 30 Wood Boring Drills 34,35

Wood Boring Drills

33-35

Aluminium/Plastic Cutters

34 36 - 39

14 000 12 000 10 000 9 000 8 000

RESHARPENING Tools can be returned to Data Powertools or sent to your local service shop. WHEN USING A ROUTING MACHINE, PROTECTION AGAINST INJURY SHOULD ALWAYS BE USED. •

EAR PROTECTION

• •

SAFETY GLASSES DUST MASK AND/OR EXTRACTION SYSTEM

IMPORTANT Router bits turn clockwise in the free hand position and anticlockwise when inverted in a router table. Always feed your workpiece against the rotation. Work holding jigs should be used in these instances. Failure to do so may harm router bits or cause injury.

12 13

Window Sash

PLASTICS ALUMINIUM & NONFERROUS METALS 18 14 12 11 10

34 15,19 30,31 20 27 16 36 -39 22 15,17 6 32,33 23,24 4,5,6

Table Edge Bits

Replaceable Insert Router Bits

ROUTER SPEED GUIDE ROUTER BIT DIAMETER

PA G E

more than powertools

Premium Quality

ROUTER BITS

STRAIGHT BITS - STRAIGHT FLUTE SINGLE FLUTE

TWO FLUTE

For all general purpose routing and grooving. Has the added advantage of chip clearance.

For all general purpose routing, grooving, rebating. For longer life in routing abrasive type materials.

B SOLID CARBIDE

PART No. T T T T T T T T T T T T

202 202 203 203 204 205 204 206 205 207 206 208

in. 1/16 5/64 3/32 1/8 5/32 5/32 3/16 7/32 15/64 1/4

S MS S MS S S MS S MS S MS S

B mm 1.6 2 2.4 3 3.2 4 4 4.8 5 5.5 6 6.35

SOLID CARBIDE

6.35 mm (1/4”) SHANK in. 3/16 3/16 3/16 1/4 5/16 3/8 7/16 1/2 1/2 1/2 5/8 5/8

C mm 4.8 4.8 4.8 6.35 7.9 9.5 11.1 12.7 12.7 12.7 15.9 15.9

in. 1-1/2 1-1/2 1-1/2 1-1/2 1-1/2 1-1/2 1-1/2 1-1/2 1-1/2 1-1/2 1-1/2 1-1/2

6.35 mm (1/4”) SHANK mm 38.1 38.1 38.1 38.1 38.1 38.1 38.1 38.1 38.1 38.1 38.1 38.1

PART No. T 206 M TX 206 M T 208 TX 208 TXX 208

A in. 15/64 15/64 1/4 1/4 1/4

B mm 6 6 6.35 6.35 6.35

in. 5/8 1-1/8 5/8 1-1/8 1-1/8

C mm 16 28.6 15.9 28.6 28.6

in. 1-1/2 2-1/4 1-1/2 2-1/4 2-1/2

mm 38.1 57.1 38.1 57.1 63.5

B CARBIDE TIPPED

PART No.

SOLID CARBIDE

6.35 mm (1/4”) SHANK PART No. T T T T T T

1804 1804 1806 1805 1806 1808

S MS S MS MS S

A in. 1/8 5/32 3/16 15/64 1/4

B mm 3.2 4 4.8 5 6 6.35

in. 1/2 5/8 3/4 3/4 1 1

C mm 12.7 15.9 19 19 25.4 25.4

in. 2-1/4 2-1/4 2-1/4 2-1/4 2-1/4 2-1/4

mm 57.1 57.1 57.1 57.1 57.1 57.1

LONG SERIES SINGLE FLUTE

CARBIDE TIPPED

12.7 mm (1/2”) SHANK PART No. T 1410 MS T 1413 MS T 1416 MS

A in. 25/64 33/64 5/8

6.35 mm (1/4”) SHANK

LONG SERIES SINGLE FLUTE

B mm 10 13 16

in. 1 1-1/2 1-1/2

C mm 25.4 38.1 38.1

Tel 0845 2300299

in. 2-5/8 3-5/32 3-5/32

mm 67 80.2 80.2

T 207 M T 209 T 210 T 208 M TX 208 M T 209 M T 212 TX 212 T 210 M TX 210 M T 211 M T 214 T 212 M T 216 TX 216 T 213 M TX 213 M T 214 M T 218 T 215 M T 220 TX 220 T 216 M TX 216 M T 216.5 M T 217 M T 222 T 218 M TX 218 M T 218.5 M T 219 M T 224 T 219.5 M T 220 M T 226 T 221 M T 222 M T 228 T 225 M T 232

Fax 0870 0117309

A in. 9/32 5/16 5/16 5/16 23/64 3/8 3/8 25/64 25/64 7/16 7/16 15/32 1/2 1/2 33/64 33/64 35/64 9/16 19/32 5/8 5/8 5/8 5/8 21/32 43/64 11/16 45/64 45/64 3/4 3/4 49/64 13/16 53/64 7/8 63/64 1

B mm 7 7.1 7.9 8 8 9 9.5 9.5 10 10 11 11.1 12 12.7 12.7 13 13 14 14.3 15 15.9 15.9 16 16 16.5 17 17.5 18 18 18.5 19 19 19.5 20 20.6 21 22 22.2 25 25.4

in. 3/4 3/4 3/4 3/4 1 3/4 3/4 1 3/4 1 3/4 3/4 3/4 3/4 1 3/4 1 3/4 3/4 3/4 3/4 1 3/4 1 3/4 3/4 3/4 3/4 1 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4

C mm 19 19 19 19 25.4 19 19 25.4 19 25.4 19 19 19 19 25.4 19 25.4 19 19 19 19 25.4 19 25.4 19 19 19 19 25.4 19 19 19 19 19 19 19 19 19 19 19

in. 1-3/4 1-3/4 1-3/4 1-3/4 2 1-3/4 1-3/4 2 1-3/4 2 1-3/4 1-3/4 1-3/4 1-3/4 2 1-3/4 2 1-3/4 1-3/4 1-3/4 1-3/4 2 1-3/4 2 1-3/4 1-3/4 1-3/4 1-3/4 2 1-3/4 1-3/4 1-3/4 1-3/4 1-3/4 1-3/4 1-3/4 1-3/4 1-3/4 1-3/4 1-3/4

E-mail sales@datapowertools.co.uk

mm 44.4 44.4 44.4 44.4 50.8 44.4 44.4 50.8 44.4 50.8 44.4 44.4 44.4 44.4 50.8 44.4 50.8 44.4 44.4 44.4 44.4 50.8 44.4 50.8 44.4 44.4 44.4 44.4 50.8 44.4 44.4 44.4 44.4 44.4 44.4 44.4 44.4 44.4 44.4 44.4

Premium Quality

STRAIGHT BITS END VIEW

END CUTTING

TWO FLUTE

For plunge cutting deep or repetitive holes in addition to normal groove, trim and rebate routing.

12.7 mm (1/2”) SHANK C

ROUTER BITS

SOLID CARBIDE INSERT

B B CARBIDE TIPPED - TWO FLUTE

12.7 mm (1/2”) SHANK A PART No. T T T T

1406 M 1408 1410 1408 M

A in. 15/64 1/4 5/16 5/16

B mm 6 6.35 7.9 8

PART No.

in. 5/8 5/8 3/4 3/4

mm 15.9 15.9 19 19

in. 2-3/4 2-3/4 2-7/8 2-7/8

mm 70 70 73 73

C in. 1 1 1 1 1 1 1-1/4 1-1/4 2 1-1/4 2 1-1/4 1-1/4 1-1/2 1-1/2 2 1-1/2 2 1-1/2 1-1/2 1-1/2 1-1/2 2 1-1/2 1-1/2 2 1-1/2 2 1-1/2 1-1/2 1-1/2 1-1/2 1-1/2 1-1/2 1-1/4 1-1/4 1-1/4 1-1/4 1-1/4 1-1/4 1-1/4 1-1/4

mm 25.4 25.4 25.4 25.4 25.4 25.4 31.8 31.8 50.8 31.8 50.8 31.8 31.8 38.1 38.1 50.8 38.1 50.8 38.1 38.1 38.1 38.1 50.8 38.1 38.1 50.8 38.1 50.8 38.1 38.1 38.1 38.1 38.1 38.1 31.8 31.8 31.8 31.8 31.8 31.8 31.8 31.8

in. 2-3/4 2-3/4 2-3/4 2-3/4 2-3/4 2-3/4 3 3 3-3/4 3 3-3/4 3 3 3-1/4 3-1/4 3-3/4 3-1/4 3-3/4 3-1/4 3-1/4 3-1/4 3-1/4 3-3/4 3-1/4 3-1/4 3-3/4 3-1/4 3-3/4 3-1/4 3-1/4 3-1/4 3-1/4 3-1/4 3-1/4 3 3 3 3 3 3 3 3

mm 70 70 70 70 70 70 76 76 95 76 95 76 76 82 82 95 82 95 82 82 82 82 95 82 82 95 82 95 82 82 82 82 82 82 76 76 76 76 76 76 76 76

T T T T T T T

CARBIDE TIPPED

12.7 mm (1/2”) SHANK PART No. T 1409 M T 1412 T 1410 M T 1411 M T 1414 T 1412 M TX 1412 M T 1416 TX 1416 T 1413 M TX 1413 M T 1414 M T 1418 T 1415 M T 1420 TX 1420 T 1416 M TX 1416 M T 1416.5 M T 1417 M T 1422 T 1418 M TX 1418 M T 1418.5 M T 1419 M TX 1419 M T 1424 TX 1424 T 1419.5 M T 1420 M T 1426 T 1428 T 1425 M T 1432 T 1436 T 1432 M T 1435 M T 1448 T 1452 T 1456 T 1460 T 1464

A in. 23/64 3/8 25/64 7/16 7/16 15/32 15/32 1/2 1/2 33/64 33/64 35/64 9/16 19/32 5/8 5/8 5/8 5/8 21/32 43/64 11/16 45/64 45/64 3/4 3/4 3/4 3/4 49/64 13/16 7/8 63/64 1 1-1/8 1-3/8 1-1/2 1-5/8 1-3/4 1-7/8 2

B mm 9 9.5 10 11 11.1 12 12 12.7 12.7 13 13 14 14.3 15 15.9 15.9 16 16 16.5 17 17.5 18 18 18.5 19 19 19 19 19.5 20 20.6 22.2 25 25.4 28.6 32 35 38.1 41.3 44.4 47.6 50.8

1410M 1413M 1416M 1418M 1419M 1425M 1432M

E/C E/C E/C E/C E/C E/C E/C

A in. 25/64 33/64 5/8 45/64 3/4 63/64 -

B mm 10 13 16 18 19 25 32

in. 1 1-1/4 1-1/2 1-1/2 1-1/2 1-1/2 1-1/4

C mm 25.4 31.8 38.1 38.1 38.1 38.1 31.8

in. 2-3/4 3 3-1/4 3-1/4 3-1/4 3-1/4 3

mm 70 76 82 82 82 82 76

ECONOMY ROUTER BIT SETS

GREENLINE KIT • 12 Pieces • Anti Kickback Design Wooden Presentation Box Contains: 3 - Straight Bits (1/4”,1/2”,3/4”) 1 - 1/2” Core Box Bit 1 - 1/2” V Groove Bit 1 - Dovetail Bit 1 - 1/2” Flush Trim Bit with bearing 1 - 1/2” Cove Bit with bearing 1 - 3/8” Rebating Bit with bearing 1 - 1/2” Rounding Over Bit with bearing 1 - 1/4” Roman Ogee Bit with bearing 1 - 45o Chamfer Bit with bearing • 1/2'' Shank - Part No. TKIT-12-1/2

BUDGET KIT • 12 Pieces • Anti Kickback Design Wooden Presentation Box Contains: 3 - Straight Bits ( 6, 12, 16mm) 1 - 1/2” Core Box Bit 1 - 1/2” V Groove Bit 1 - Dovetail Bit 1 - 1/2” Flush Trim Bit with bearing 1 - 1/4 Cove Bit with bearing 1 - 1/4 Rounding Over Bit with bearing 1 - 3/8 Rounding Over Bit with bearing 1 - 4mm Roman Ogee Bit with bearing 1 - 45o Chamfer Bit with bearing

STRAIGHT BIT WITH DOWN SHEAR

• 1/4'' Shank - Part No. TBUD-12 C

Reduces top edge breakout. Ideal for veneered and laminated boards.

12.7 mm (1/2”) SHANK PART No. TSH 1424 TSHX 1424

A in. 3/4 3/4

B mm 19.0 19.0

in. 1-1/2 1-61/64

www.datapowertools.co.uk

C mm 38.1 50.0

in. 2-1/4 3-23/37

mm 57.2 94.5

more than powertools

Premium Quality

STRAIGHT BITS

L A M I N AT E T R I M B I T S

RIP & SLOTTER BIT

FLUSH TRIMMING BITS

ROUTER BITS

A slotting and fast cutting roughing bit. C

For edge trimming of laminated sink tops.

SOLID CARBIDE - SINGLE FLUTE

6.35 mm (1/4”) SHANK A

PART No.

in. 1/4

T 803 - 509

mm 6.35

in. 3/8

CARBIDE TIPPED - WITH PILOT

C mm 9.5

in. 1 1/2

6.35 mm (1/4”) SHANK

mm 38.1

PART No

SLOT MORTISE BITS

A in.

B mm

in.

C mm

in.

2-3/8

SINGLE FLUTE CARBIDE TIPPED

A long series bit for slot mortise joints. Note: Due to the extreme length of these bits they should be used in a table mounted routing machine only. These bits are not guaranteed against breakage.

T 1910

5/16

T 1910 2

5/16

13/16

20.6

TWO FLUTES CARBIDE TIPPED 8

13/16

20.6

B TWO FLUTE END CUTTING WITH CHIP BREAKER

12.7 mm (1/2”) SHANK A

B mm in. mm SOLID CARBIDE INSERT 5/16 8 1-1/2 38.1 3/8 9.5 1-1/2 38.1 CARBIDE TIPPED 33/64 13 2 50.8

PART No.

in.

TSM 1408 M TSM 1409.5M TSM 1413 M

COMBINATION FLUSH TRIMMING & DRILLING BITS

A C in.

3-5/8 3-5/8

92 92

3-3/4

HINGE MORTISE BITS

This bit drills its own hole for blind routing in plywood and soft metals. Eliminates fitting edges at window and floor openings.

WITH PILOT

Can be used as a fast cutting stair tread bit or making mortises from edge of work.

SUFFIX 1/2 = 1/2” SHANK, SUFFIX 3/8 = 3/8” SHANK, OTHERWISE 1/4” PART No

A in.

B mm

in.

C mm

in.

2-3/4 2-3/4 3 3-1/2

70 70 76 89

2-3/4

B TWO FLUTE

SINGLE FLUTE CARBIDE TIPPED

6.35 mm (1/4”) SHANK

PART No.

T 2016

in.

1/2

CARBIDE TIPPED 12.7 13/32 10.3

in.

T T T T

C mm

T T T T

1622 1624 1626 1628

1/2 1/2 1/2 1/2

T 1510 2

A in.

B mm

in.

CARBIDE TIPPED 17.5 3/4 19 3/4 20.6 3/4 22.2 3/4

11/16 3/4 13/16 7/8

in.

19 19 19 19

2-1/2 2-1/2 2-1/2 2-1/2

63.5 63.5 63.5 63.5

A fast cutting roughing bit for heavy stock removal. B

TST 1413 M TSTX 1413 M

7/8 13/16 1 1

22.2 20.6 25.4 25.4

5/16

13/16

20.6

B mm in. mm SOLID CARBIDE INSERT 3/8 9.5 1-1/2 38.1 CARBIDE TIPPED 33/64 13 1-3/4 44.5 33/64 13 2-1/4 57.1

A C

in.

Tel 0845 2300299

in.

For sales enquires or technical information please call

Tel 0845 2300299

CARBIDE TIPPED

12.7 mm (1/2”) SHANK

TST 1409.5 M

6.35 8 9.5 12.7

C mm

STAGGERED TIP BITS

PART No.

1/4 5/16 3/8 1/2

TWO FLUTES CARBIDE TIPPED

12.7 mm (1/2”) SHANK PART No.

1508 1510 1512 3/8 1516 1/2

3-5/8

3-1/2 4

89 102

and speak to one of our team

Fax 0870 0117309

E-mail sales@datapowertools.co.uk

Premium Quality

ROUTER BITS

L A M I N AT E T R I M B I T S & C U T T E R S This bit has been specially designed for template work in softer timbers. Where a single bearing might create an indentation on the timber, this bit has double the surface area to ensure template surface is not damaged.

FLUSH TRIMMING BITS A popular bit for fast smooth and accurate trimming cuts for laminates and template work.

B CARBIDE TIPPED - TWO FLUTE WITH BALL BEARING GUIDE

CARBIDE TIPPED - TWO FLUTE WITH DOUBLE BALL BEARING GUIDE

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4” A

PART No.

in. T 8008 B 1/4 T 8012 B 3/8 TS 8016 B 1/2 T 8016 B 1/2 T 8016 B 1/2 1/2 TX 8016 B 1/2 1/2 TXX 8016 B 1/2 1/2 T 8020 B 5/8 T 8020 B 1/2 5/8 T 8028 B 1/2 0.866 TX 8028 B 1/2 0.866

B mm 6.35 9.5 12.7 12.7 12.7 12.7 12.7 15.9 15.9 22 22

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4”

in. 1 1 5/8 1 1 1-1/2 2 1 1 1 1-1/2

C mm 25.4 25.4 15.9 25.4 25.4 38.1 50.8 25.4 25.4 25.4 38.1

in. 2-3/8 2-5/8 2-1/4 2-1/2 3-1/8 3-3/8 3-7/8 2-5/8 3-1/8 3-3/8 3-3/4

Bearing No. TB 6 TB 9 TB 11 TB 11 TB 11 TB 11 TB 11 TB 14 TB 14 TB 12 TB 12

mm 60 63.5 57.1 67 79 86 98 67 79 86 95

FLUSH TRIM BIT WITH DOWN SHEAR

PART No.

in. T 8012 BB 3/8 TS 8016 BB 1/2 T 8016 BB 1/2 T 8016 BB 1/2 1/2 TX8016 BB 1/2 1/2 TXX8016 BB 1/2 1/2 T 8020 BB 5/8 T 8020 BB 1/2 5/8 T 8028 BB 1/2 0.866 TX 8028 BB 1/2 0.866

B mm 9.5 12.7 12.7 12.7 12.7 12.7 15.9 15.9 22 22

in. 1 5/8 1 1 1-1/2 2 1 1 1 1-1/2

mm 25.4 15.9 25.4 25.4 38.1 50.8 25.4 25.4 25.4 38.1

C in. mm 2-3/4 70 2-3/8 60 2-3/4 70 3-3/8 86 3-7/8 98 4-1/4 108 3 76 3-3/8 86 3-1/2 89 3-15/16 100

Bearing No. TB 9 TB 11 TB 11 TB 11 TB 11 TB 11 TB 14 TB 14 TB 12 TB 12

INVERTED FLUSH TRIMMING BITS A handy bit for copy work where the template is between the work and the router.

For minimal chipping and superior finish.

C CARBIDE TIPPED - TWO FLUTES WITH BALL BEARING GUIDE

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4” A A PART No. TSH 8024 B 1/2 TSHX 8024 B 1/2

A in. 3/4 3/4

B mm in. 19.0 1-1/2 19.0 1-61/64

mm 38.1 50.0

Bearing in. mm No. 3-39/64 91.7 TB 16 4 101.6 TB 16

OVERHANG TRIMMING BIT This bit will leave a 1/8” overhang in order that the final flush trimming cut is a light one for the smoothest possible finish.

PART No. T 8216 B T 8220 B T 8224 B 1/2 TX 8224 B 1/2 T 8236 B 1/2

A in. 1/2 5/8 3/4 3/4 1-1/8

B mm 12.7 15.9 19 19 28.6

in. 3/4 3/4 1-1/2 2 1-1/2

mm 19 19 38.1 50.8 38

C Bearing in. mm No. 2-1/8 54 TB 7 2-3/16 55 TB 14 3-5/8 92.1 TB 4 4-5/32 105.6 TB 4 3-1/3 89 TB 18

INVERTED FLUSH TRIM BIT with Down Shear C

B B CARBIDE TIPPED - TWO FLUTES WITH BALL BEARING GUIDE

6.35 mm (1/4”) SHANK

PART No. PART No. TO 8012 B

A in. 3/8

B mm 9.5

in. 1

C mm 25.4

in. 2-3/4

mm 70

TSH 8224 B 1/2 TSHX 8224 B 1/2

A in. 3/4 3/4

mm 19 19

B in. mm 1-1/2 38.1 1-61/64 50

C Bearing in. mm No. 3-39/64 91.7 TB 4 4 101.6 TB 4

Replacement Ball Bearing TB8

COMBINATION FLUSH & BEVEL TRIMMING BITS

A versatile bit with ball bearing guide. By adjusting the depth this bit will either flush trim or bevel trim. Bevel

CARBIDE TIPPED - TWO FLUTES WITH BALL BEARING GUIDE

6.35 mm (1/4”) SHANK PART No. T 9122 B T 9130 B

A in. 3/4 7/8

B mm 19 22.2

in. 0.580 0.580

C mm 14.7 14.7

in. 2-3/16 2-3/16

mm 55 55

220 300

Replacement Ball Bearing TB11

Tel 0845 2300299

BEVEL

Fax 0870 0117309

E-mail sales@datapowertools.co.uk

Premium Quality

L A M I N AT E T R I M B I T S & C U T T E R S

Bevel

For extra smooth trimming. Assembly includes 3 flute cutter, bearing, arbor, spacers and nut.

Bevel

A time saving bit that will trim both sides of the board in one pass. Washers provided enable cutters to be separated the correct distance to suit thickness of board to be trimmed.

CARBIDE TIPPED - FOUR FLUTES WITH BALL BEARING GUIDE

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4”

FLUSH AND BEVEL TRIMMING ASSEMBLIES SOLID CARBIDE - THREE FLUTES WITH BALL BEARING GUIDE

PART No.

6.35 mm (1/4”) SHANK PART No. TA 193.00 B TA 193.22 B

BEVEL

Arbor No.

in. 3 3-1/4 3 3-1/4 3 3-1/4 3 3-1/4

15.9mm

BEVEL

Arbor No.

Flush 220

TA 9 TA 9

TDA TDA TDA TDA TDA TDA TDA TDA

C in. 2-3/8 2-3/8

mm 60 60

Replacement Ball Bearing TB14 For oversize Bearing use TB16

194.00 194.00 194.15 194.15 194.25 194.25 194.45 194.45

B B B B B B B B

1/2 1/2 1/2 1/2

FLUSH FLUSH 150 150 250 250 450 450

TA TA TA TA TA TA TA TA

13 14 13 14 13 14 13 14

mm 76 82 76 82 76 82 76 82

ROUTER BITS

DOUBLE FLUSH AND BEVEL TRIMMING ASSEMBLIES

PROFESSIONAL RANGE - 3 Flutes

Replacement Ball Bearing TB12 REPLACEMENT TRIMMING CUTTERS SOLID CARBIDE - THREE FLUTES

6.35 mm (1/4”) BORE PART No.

BEVEL

T 193.00 T 193.22

Flush 220

mm 15.9 22.2

194.00 194.00 194.15 194.15 194.25 194.25 194.45 194.45

B B B B B B B B

1/2 1/2 1/2 1/2

22mm

Flush Flush 150 150 250 250 450 450

TA TA TA TA TA TA TA TA

C in. 2-1/2 2-1/2 2-1/2 2-1/2 2-1/2 2-1/2 2-1/2 2-1/2

1 3 1 3 1 3 1 3

150 250 450

in. 1 1-1/8 1-3/8

mm 25.4 28.6 35

For sales enquires or

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4”

TA TA TA TA TA TA TA TA

BEVEL

FLUSH AND BEVEL TRIMMING ASSEMBLIES CARBIDE TIPPED - FOUR FLUTES WITH BALL BEARING GUIDE

Arbor No.

PART No.

A A

Bevel

These tools produce a chatter-free trimmed edge. At high feed rates they produce a superior finish to any other tool. Assembly includes 4 flute cutter, arbor (1/4” or 1/2” shank), bearing, nut and washer.

BEVEL

8 mm (5/16”) BORE

T 194.15 LH T 194.25 LH T 194.45 LH

H IGH PERFORMANCE PROFESSIONAL RANGE - 4 Flutes

PART No.

REPLACEMENT LEFT HAND TRIMMING CUTTERS

A in. 5/8 7/8

mm 63.5 63.5 63.5 63.5 63.5 63.5 63.5 63.5

Replacement Ball Bearing TB12 For oversize Bearing use TB13

technical information please call

Tel 0845 2300299 and speak to one of our team

REPLACEMENT TRIMMING CUTTERS CARBIDE TIPPED - FOUR FLUTES

8 mm (5/16”) BORE PART No.

BEVEL

T T T T

Flush 150 250 450

194.00 194.15 194.25 194.45

A A in. .866 1 1-1/8 1-3/8

mm 22 25.4 28.6 35

www.datapowertools.co.uk

more than powertools

Premium Quality

ROUTER BITS

L A M I N AT E T R I M B I T S & C U T T E R S COMBINATION FLUSH TRIMMING & DRILLING BIT

FLUSH TRIMMING BIT Makes square trim edge cuts. Has integral pilot C

Drills through surface laminate into pre-cut opening and trims edge square in one operation.

B B SOLID CARBIDE SINGLE FLUTE WITH PILOT

SOLID CARBIDE SINGLE FLUTE WITH PILOT

PART No.

6.35 mm (1/4”) SHANK

in. 1/4

T 303-500

T 703-507

A in. 1/4

B mm 6.35

in. 5/8

in. 1-1/2

mm 38.1

Provides 7° bevel to trim the edge of plastic laminated surfaces. Built-in pilot eliminates guide assembly.

T 403-501

C mm 6.35

in. 1-1/2

mm 38.1

Provides a 22˚ or 0˚ straight cut on the edge of plastic laminated surfaces.

B A

CARBIDE TIPPED TWO FLUTES

6.35 mm (1/4”) SHANK

A A

PART No.

6.35 mm (1/4”) SHANK A

B mm 6.35

in. 1/4

COMBINATION FLUSH & 22˚ BEVEL TRIMMING BITS

SOLID CARBIDE - SINGLE FLUTE WITH PILOT

in. 1/4

B mm 6.35

C mm 16

7˚ BEVEL TRIMMING BIT

PART No.

6.35 mm (1/4”) SHANK

PART No.

in. 1/2

T 2622 TX 2622

C mm 12.7

in. 1-1/2

in. 15/32 9/16

B mm 12 14.3

in. 7/16 5/8

C mm 11 16

in. 1-5/8 2-1/8

mm 41 54

mm 38.1

30˚ BEVEL TRIMMING BITS

COMBINATION FLUSH & 7˚ BEVEL TRIMMING BIT

Provides a 30˚ bevel to trim the edge of plastic laminated surfaces.

B A

Provides 7° bevel or 0° square cut on the edge of plastic laminated surfaces.

CARBIDE TIPPED - TWO FLUTES

6.35 mm (1/4”) SHANK B

PART No.

in. 5/8 5/8

TBD 30 TBDX 30

B mm 15.9 15.9

in. 3/8 3/8

C mm 9.5 9.5

in. 1 1-3/8

mm 25.4 35

SOLID CARBIDE SINGLE FLUTE

EDGE BAND TRIM BITS

6.35 mm (1/4”) SHANK PART No. T 2614

A in. 1/4

B mm 6.35

in. 3/8

C mm 9.5

in. 1-1/2

mm 38.1 C

COMBINATION FLUSH & 22˚ BEVEL TRIMMING BITS

C B

B R

Provides 22° bevel or 0° square cut on the edge of plastic laminated surfaces.

TEG

TLE

A PART No. TLE 24 TLE 24 LH

SOLID CARBIDE - SINGLE FLUTE

6.35 mm (1/4”) SHANK PART No. TBD 22 TBDX 22

B mm 6.35 6.35

B mm 19.0 19.0

in. 31/64 31/64

C mm in. mm 12.3 1-45/64 43.3 12.3 1-45/64 43.3

R RADIUS in. mm 5/64 2.0 5/64 2.0

15˚ BEVEL

A in. 1/4 1/4

A in. 3/4 3/4

in. 1/2 1/2

C mm 12.7 12.7

Tel 0845 2300299

in. 1 1-1/2

mm 25.4 38.1

PART No. TEG 15 TEG 15 LH

Fax 0870 0117309

A in. 1-17/64 1-17/64

B mm 32.0 32.0

in. 33/64 33/64

C mm 13.0 13.0

in. 1-1/2 1-1/2

E-mail sales@datapowertools.co.uk

mm 38.1 38.1

Premium Quality

GROOVE FORMING BITS DRAW PULL BITS

DOVETAIL BITS

These bits will produce a hidden handle on drawers and cupboard doors.

TWO FLUTE

SUFFIX 1/2 = 1/2” SHANK, SUFFIX 3/8 = 3/8” SHANK, SUFFIX 10mm = 10mm SHANK, OTHERWISE 1/4” A

PART No.

in.

9/32

T T T T T T T

1/2 9/16 9/16 9/16 9/16 19/32 3/4

1016 1018 1018 1018 1018 1019 1024

3/8 10MM 1/2 1/2

B mm

T 1012

C R

SOLID CARBIDE 7.1 9.5 CARBIDE TIPPED 12.7 13.5 14.3 13.5 14.3 13.5 14.3 13.5 14.3 13.5 15 12.7 19 26

CARBIDE TIPPED - TWO FLUTES

1-1/2 1-3/4 1-3/4 2-3/4 2-3/4 2-3/4 1-3/4 2-3/4

Bevel

C in.

ROUTER BITS

For dovetail joint, drawer fronts, etc. for the quality minded craftsman.

Bevel

PART No.

in. TDC 16 1/2 1-3/4 TDC 20 1/2 2 TDC 24 1/2 2-1/4

38.1

5˚

44.4 44.4 70 70 70 44.4 70

15˚ 15˚ 15˚ 15˚ 15˚ 15˚ 5˚

12.7mm (1/2”) SHANK

B mm 44.4 50.8 57.1

in. 1/2 9/16 3/4

C mm 12.7 14.3 19

in. 2-1/2 2-9/16 2-5/8

mm 63.5 65 67

R RADIUS in. mm 1/2 12.7 9/16 14.3 3/4 19

These bits produce a recessed handle on drawers or cupboard doors that is both decorative and functional. C

DOVETAIL “GIFKINS” BITS

CARBIDE TIPPED - TWO FLUTES

PART No.

A PART No. TGAD 12 TGBD 16 1/2 TGAS 12 TGBS 16 1/2 TGHD12 TGHS12

in. 3/8 5/8 3/8 1/2 .244 .433

B mm 9.5 15.9 9.5 12.7 6.2 11

TDP 20 TDP 20 1/2 TDP 35 1/2

A in. 1 1 1-1/4

B mm 25.4 25.4 31.8

in. .609 .609 .760

C mm 15.5 15.5 19.3

in. 2 2-3/8 2-3/4

mm 50.8 60 70

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4”

To suit ‘Gifkins’ Dovetail Jig.

in. 33/64 33/64 25/64 25/64

C mm 13.0 22.0 13.0 22.0 10 10

in. 2-1/2 2-5/16 2-31/64 3-5/16 2-1/4 2-1/4

Bevel

mm 63.5 84.0 63.0 84.0 57.1 57.1

8˚ 8˚ 0˚ 0˚ 7˚ 0˚

HOOK SLOT BITS This bit will quickly drill and slot a convenient screw, nail or hook slot in the back of a picture frame, hanging shield, etc.

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4”

A1 A2

A1 A2 in. mm in. mm THS 12 .355 9 3/16 4.8 THS 16 1/2 12.7 5/16 8 THS 16 1/2 1/2 12.7 5/16 8 PART No.

DOVETAIL“LEIGH” BITS To suit the ‘Leigh’ Dovetail Jig.

CARBIDE TIPPED - SINGLE FLUTE

in. 1/8 1/8 1/8

B1 mm 3.2 3.2 3.2

in. 3/8 1/2 1/2

B2 C mm in. mm 9.5 1-5/8 41 12.7 1-3/4 44.4 12.7 2-5/8 67

For sales enquires or technical information please call

Bevel

Tel 0845 2300299

C CARBIDE TIPPED TWO FLUTES

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4” PART No. TL 70 TL 80 TL 90 1/2 TL 100 1/2 TL 120 TL 140 TL 150 1/2 TL 160 1/2

B A A

in. 3/8 1/2 11/16 13/16 1/2 5/16 7/16 1/2

B mm 9.5 12.7 17.4 20.6 12.7 8 11.1 12.7

in. 1/2 13/16 1 1-1/4 1/2 1 1 1

A C

mm 12.7 20.6 25.4 31.8 12.7 25.4 25.4 25.4

www.datapowertools.co.uk

in. 2-3/8 2-3/4 2-7/8 3-1/8 2-3/8 2-7/8 3 3

mm 60 70 73 79 60 73 76 76

8˚ 8˚ 8˚ 8˚ 14˚ 0˚ 0˚ 0˚

and speak to one of our team ®

more than powertools

Premium Quality

ROUTER BITS

GROOVE FORMING BITS T- SLOT CUTTERS Use T 1410 M first to cut neck.

This bit has a carbide tip on the throat which allows the T-slot to be cut in one pass.

This bit allows you to make horizontal T-slots when used in hanging brackets, or creating wall display units. C

CARBIDE TIPPED - TWO FLUTES

12.7mm (1/2”) SHANK

TS 28 1/2

in. 1-1/8

mm 28

in. 3/8

C mm 9.5

in. 2-3/8

CARBIDE TIPPED - TWO FLUTES

12.7mm (1/2”) SHANK

A2 A1

PART No.

A1 A2 mm in. mm TSA 30 1/2 1-3/16 30 25/64 10

PART No.

mm 60

in.

in. -

B1 B2 C mm in. mm in. mm 22 25/64 10 3-5/32 80

EDGE & FACE FORMING BITS “V” GROOVE BITS

22.5˚ VEE GROOVE BITS

90˚ VEE GROOVE BITS

22.5 Degree included Angle Single Flute - Solid Carbide

A versatile bit for decorative vee grooves and chamfering. Used for sign and lettering work. Also mitre joints for box fabrication.

C B

0.5mm Flat

A PART No. TV 2208 TV 2216 1/2

A in. 1/4 1/2

B mm 6.4 12.7

in. 37/64 1-13/64

C mm 14.7 30.6

in. 1-1/2 3

mm 38.1 76.2

A 90° INCLUDED ANGLE TWO FLUTES CARBIDE TIPPED

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4”

30˚ VEE GROOVE BITS

PART No.

30 Degree included Angle - Single Flute - Solid Carbide

TV 3008 TV 3016 1/2

B mm 6.4 12.7

in. -

in.

C mm

in.

9.5 22 22 28 32

1-3/4 2 2-1/2 3-3/8 3

44.4 50.8 63.5 86 76

CARBIDE TIPPED T T T T T

0.5mm Flat

in. 1/4 1/2

B mm

PART No.

A in.

112 128 128 1/2 1230 1/2 1240 1/2

45/64 1-15/64 1-15/64 1-9/16 2

18 31.3 31.3 39.7 50.8

3/8 7/8 7/8 1-1/8 1-1/4

C mm 10.9 22.8

in. 1-1/2 3

mm 38.1 76.2

60˚ VEE GROOVE BITS This bit is specifically designed for sign and lettering work.

120˚ VEE GROOVE BITS 120 Degree Included Angle – Two Flute – Carbide Tipped

B A

60° INCLUDED ANGLE CARBIDE TIPPED - TWO FLUTES

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4” PART No. T 6128 T 6128 1/2

A in. 1 1

B mm 25.4 25.4

in. 1 1

PART No.

C mm 25.4 25.4

Tel 0845 2300299

in. 2-1/4 2-3/4

mm 57.1 70

TV 1232 TV 1232 1/2 TV 1264 1/2

Fax 0870 0117309

A in. 1 1 2

B mm 25.4 25.4 50.8

in. 57/64

mm 11.4 11.4 22.7

C in. 1-45/64 2-13/64 2-29/32

E-mail sales@datapowertools.co.uk

mm 43.3 55.9 73.8

Premium Quality

EDGE & FACE FORMING BITS HALF CORE BOX BITS

For recess design veining in fine cabinet surfaces. Designed for template routing.

A A

6.35 mm (1/4”) SHANK

T T T T

503-502 503-503 503-504 503-505

A in. 3/32 1/8 3/16 1/4

B mm 2.4 3.2 4.8 6.35

in. 1/4 1/4 1/4 3/8

C mm 6.35 6.35 6.35 9.5

in. 1-1/2 1-1/2 1-1/2 1-1/2

mm 38.1 38.1 38.1 38.1

PART No. THC 45 1/2 THC 75 1/2

VEINING BITS For grooving and scoring panel designs in wood surfaces such as cupboard doors.

T T T T T T

302 303 304 305 306 307

B mm

in.

C R RADIUS mm in. mm in. mm 17.0 2-45/64 68.7 45.0 18.3 2-13/16 71.4 2-61/64 75.0

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4” C

SOLID CARBIDE 1.6 3/16 4.8 2.4 3/16 4.8 3.2 5/16 7.9 4 5/16 7.9 4.8 7/16 11.1 5.5 7/16 11.1

1/16 3/32 1/8 5/32 3/16 7/32

in. 43/64 23/32

TWO FLUTES

A in.

B mm 63.5 76.2

Used for panel doors and decorative edge moulds.

6.35 mm (1/4”) SHANK

A in. 2-1/2 3

OGEE BITS

SINGLE FLUTE

PART No.

90° INCLUDED ANGLE SOLID CARBIDE - SINGLE FLUTE

PART No.

ROUTER BITS

PROVINCIAL DESIGN VEINING BITS

in.

1-1/2 1-1/2 1-1/2 1-1/2 1-1/2 1-1/2

38.1 38.1 38.1 38.1 38.1 38.1

A2 A1

PART No.

A1 mm

A2 mm

T T T T T T T T

9.9 9.9 16.2 16.2 23.8 23.8 31.2 31.2

3.6 3.6 3.6 3.6 4.8 4.8 4.8 4.8

B in.

C mm

in.

R RADIUS in. mm

CARBIDE TIPPED

CORE BOX BITS For use in fluting flat surfaces such as mantles and facades. C

TWO FLUTE

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4”

PART No.

T 408 T T T T T T T T T T T

410 412 416 416 420 420 424 424 432 440 448

A in. 1/4

1/2 1/2 1/2 1/2 1/2 1/2

5/16 3/8 1/2 1/2 5/8 5/8 3/4 3/4 1 1-1/4 1-1/2

B mm

in.

SOLID CARBIDE 6.35 5/16 CARBIDE TIPPED 7.9 1/4 9.5 1/4 12.7 31/64 12.7 31/64 15.9 3/8 15.9 3/8 19 1/2 19 1/2 25.4 5/8 31.8 3/4 38 7/8

7502 7502 7504 7504 7506 7506 7509 7509

1/2 1/2 1/2 1/2

3/8 3/8 1/2 1/2 5/8 5/8 5/8 5/8

9.5 9.5 12.7 12.7 15.9 15.9 15.9 15.9

1-7/8 2-1/2 1-7/8 2-1/2 1-7/8 2-1/2 1-7/8 2-1/2

47 63.5 47 63.5 47 63.5 47 63.5

1/16 1/16 1/8 1/8 3/16 3/16 1/4 1/4

1.6 1.6 3.2 3.2 4.8 4.8 6.35 6.35

OGEE BITS FINE POINT

C mm

in.

1-1/2

38.1

6.35 6.35 12.2 12.2 9.5 9.5 12.7 12.7 15.9 19 22.2

1-1/4 1-1/4 1-1/2 2-1/4 1-3/4 2-1/4 1-7/8 2-1/4 2-1/2 2-1/2 2-5/8

31.8 31.8 38.1 57.1 44.4 57.1 47 57.1 63.5 63.5 67

For Ogee grooves where a fine point is required. Used extensively in router lathe work. CARBIDE TIPPED - TWO FLUTES

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4”

B R R 1mm A

PART No. TF TF TF TF

7506 7506 1/2 7509 7509 1/2

A in. .815 .815 1.040 1.040

B mm 20.7 20.7 26.4 26.4

in. 5/8 5/8 5/8 5/8

C mm 15.9 15.9 15.9 15.9

in. 1-7/8 2-1/4 1-7/8 2-1/2

mm 47 57.1 47 63.5

R RADIUS in. mm 3/16 4.8 3/16 4.8 1/4 6.35 1/4 6.35

www.datapowertools.co.uk

more than powertools

Premium Quality

ROUTER BITS

EDGE & FACE FORMING BITS OGEE BITS ROUNDED BOTTOM

CLASSICAL BITS Used for panel doors and decorative edge moulds.

Used for decorative plunge cutting, grooving or edge forming.

C CARBIDE TIPPED TWO FLUTES

B R

CARBIDE TIPPED TWO FLUTES

A PART No.

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4” A

PART No.

in. TR 7506 .937 TR 7506-1/2 .937 TR 7509 1-1/4 TR 7509-1/2 1-1/4

mm 23.7 23.7 32 32

in. .580 .580 .700 .700

C mm 14.7 14.7 17.7 17.7

in. 1-7/8 2-1/2 1-7/8 2-1/2

TC TC TC TC TC TC

R RADIUS in. mm 3/16 4.7 3/16 4.7 1/4 6.35 1/4 6.35

mm 47 63.5 47 63.5

B R

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4”

6 6 1/2 10 10 1/2 12 1/2 16 1/2

R A A

in. 1/2 1/2 3/4 3/4 57/64 1-5/32

B mm 12.7 12.7 19 19 22.6 29.2

in. 1/2 1/2 9/16 9/16 5/8 3/4

C mm 12.7 12.7 14.3 14.3 15.9 19

in. 1-3/4 2-1/2 1-3/4 2-1/4 2-1/2 2-1/2

R RADIUS in. mm 3/32 2.4 3/32 2.4 5/32 4 5/32 4 3/16 4.8 1/4 6.35

mm 44.4 63.5 44.4 57.1 63.5 63.5

TRADITIONAL CLASSICAL BITS Used for panel doors and decorative edge moulds. C

CARBIDE TIPPED - TWO FLUTES

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4” B

R2 R1

B2 R B1

PART No. TRS 7506 1/2 TRS 7509 1/2

A in. 1 -

B C R1 RADIUS R2 RADIUS mm in. mm in. mm in. mm in. mm 25.4 19/32 15.1 2-25/64 60.7 5/16 7.9 3/16 4.8 33.5 23/32 18.3 2-25/64 61.0 5/16 7.9 3/8 9.5

OGEE BITS WIDE FLAT BOTTOM Designed for grooving panel doors and decorative edge moulds.

A in. mm TTC 8 11/16 17.4 TTC 8 1/2 11/16 17.4 TTC 12 .925 23.5 TTC 12 1/2 .925 23.5 TTC 16 1/2 1.160 29.5 PART No.

B1 in. mm 0.070 1.8 0.070 1.8 0.070 1.8 0.070 1.8 1/8 3.2

B2 in. 1/2 1/2 1/2 1/2 5/8

mm 12.7 12.7 12.7 12.7 16

C in. mm 1-3/4 44.4 2-1/4 57.1 1-3/4 44.4 2-1/4 57.1 2-1/4 57.1

R RADIUS in. mm 1/8 3.2 1/8 3.2 3/16 4.8 3/16 4.8 1/4 6.35

TRADITIONAL CLASSICAL BITS with bearing C

12.7mm A CARBIDE TIPPED - TWO FLUTES

R2 B1

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4”

R1 PART No. TW TW TW TW

7506 7506 1/2 7509 7509 1/2

A in. 1-1/4 1-1/4 1-1/2 1-1/2

B mm 31.8 31.8 38.1 38.1

in. 5/8 5/8 3/4 3/4

C mm 15.9 15.9 19 19

in. 1-7/8 2-1/2 2 2-1/2

mm 47 63.5 50.8 63.5

R RADIUS in. mm 3/16 4.8 3/16 4.8 1/4 6.35 1/4 6.35

A PART No. TTCR 4 B TTCR 6 B 1/2

A mm 22.0 35.0

B1 mm 12.7 14.3

B2 mm 4.8 4.8

C mm 53.9 73.0

R1 mm 4.0 10.3

R2 mm 4.8 5.9

BEADING BITS For grooving panel designs in wood surfaces such as cupboard doors.

PROVINCIAL BITS with bearing

Used for decorative edge and face moulds.

CARBIDE TIPPED - TWO FLUTES

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4” A

R A PART No.

PART No. TCRR 3 B TCRR 5 B 1/2

A in. 1-3/8

B mm 22.0 35.0

in. 25/64 35/64

C mm in. mm 10.0 2 50.8 14.0 2-45/64 68.7

Tel 0845 2300299

B R 3.2mm

R RADIUS in. mm 1/8 3.2 5.0

TBB TBB TBB TBB

Fax 0870 0117309

4 4 1/2 8 8 1/2

A in. 3/8 3/8 5/8 5/8

B mm 9.5 9.5 15.9 15.9

in. 3/8 3/8 1/2 1/2

C mm 9.5 9.5 12.7 12.7

in. 1-3/4 2-1/4 1-3/4 2-1/4

mm 44.4 57.1 44.4 57.1

E-mail sales@datapowertools.co.uk

R RADIUS in. mm 1/8 3.2 1/8 3.2 1/4 6.35 1/4 6.35

Premium Quality

EDGE & FACE FORMING BITS This bit produces a beading on the surface of the material coming to a fine point.

This bit is used for rounding over edges in areas where a ball bearing is not required. It makes a decorative edge, or can be used to plunge completely through the material.

B R 1mm

PART No.

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4”

TBF TBF TBF TBF

4 4 1/2 8 8 1/2

in. .290 .290 -

B mm 7.4 7.4 13.7 13.7

in. 3/8 3/8 1/2 1/2

C mm 9.5 9.5 12.7 12.7

in. 1-3/4 2-5/8 1-3/4 2-5/8

TX TX TX TX TX TX TX TX TX TX

R RADIUS in. mm 1/8 3.2 1/8 3.2 1/4 6.35 1/4 6.35

mm 44.4 67 44.4 67

B A2 A1

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4”

CARBIDE TIPPED - TWO FLUTES

CARBIDE TIPPED TWO FLUTES

PART No.

BEADING BITS WIDE FLAT BOTTOM

506 508 508 512 516 520 524 508 512 516

1/2 1/2 1/2 1/2 1/2 B 1/2 B 1/2 B 1/2

A1 mm 20 25 25 33 39 45 51 24.7 32.7 38.7

A2 mm 10 13 13 13 13 13 13 12.7 12.7 12.7

B mm 16 19 19 22 25 28.6 32 19 22 25

C mm 53 57 71 74 80 82 84 71 74 80

R RADIUS mm 5 6 6 10 12 16 19 6 10 12

ROUTER BITS

EXTENDED ROUNDING OVER BITS

BEADING BITS FINE POINT

Replacement Ball Bearing TB11

Specially designed for grooving panel doors. This bit produces a beading groove with a wide bottom. C

EXTENDED DOUBLE BEADING BITS

C R2 R1

12.7mm A

CARBIDE TIPPED - TWO FLUTES

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4” PART No. TBW TBW TBW TBW

4 4 1/2 8 8 1/2

A in. 3/4 3/4 1 1

B mm 19 19 25.4 25.4

in. 7/16 7/16 3/4 3/4

C mm 11.1 11.1 19 19

R1 RADIUS R2 RADIUS PART No. in. mm in. mm in. mm in. mm in. mm TBX 604 1/2 1 25.4 1-1/8 28.6 2-29/32 73.8 1/8 3.2 1/8 3.2 TBX 606 1/2 1-1/8 28.6 1-3/16 30.2 3 76.2 3/16 4.8 1/8 3.2 A

in. 1-3/4 2-1/4 2-3/8 2-3/8

R RADIUS in. mm 1/8 3.2 1/8 3.2 1/4 6.35 1/4 6.35

mm 44.4 57.1 50.8 60

EXTENDED PROVINCIAL BITS

DOUBLE BEADING BIT WIDE FLAT BOTTOM

C R

Specially designed for grooving panel doors. Also produces a decorative edge beading.

A B C R1 RADIUS R2 RADIUS in. mm in. mm in. mm in. mm in. mm TCRX 8 1/2 1 25.4 1-15/64 31.3 3 76.2 1/8 3.2 1/8 3.2 TCRX 12 1/2 1-1/8 28.6 1-19/64 32.9 3-7/64 79.0 3/16 4.8 1/8 3.2 PART No.

R B R 12.7mm A

DISH CUT BITS This bit is used for routing trays, bowls, plates and boxes. It has a wide surface cut, to quickly remove excess material.

CARBIDE TIPPED - TWO FLUTES

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4” PART No. TBD 4 TBD 4 1/2 TBD 8 1/2

A in. 1 1 1-1/2

B mm 25.4 25.4 38.1

in. 7/16 7/16 3/4

C mm 11.1 11.1 19

in. 1-3/4 2-1/4 2-1/2

mm 44.4 57.1 63.5

R RADIUS in. mm 1/8 3.2 1/8 3.2 1/4 6.35

CARBIDE TIPPED TWO FLUTES

12.7 mm (1/2”) SHANK PART No. TD 706 1/2 TD 716 1/2

R A A mm 19 32

B mm 19 32

C mm 62 75

R RADIUS mm 4.75 6.5

www.datapowertools.co.uk

more than powertools

Premium Quality

ROUTER BITS

EDGE FORMING BITS DOUBLE REED BIT

PALACE PATTERN BITS C

An attractive edge mould for table and bench tops.

This bit gives a combination of two beads on the material. C

B1 CARBIDE TIPPED TWO FLUTE WITH BALL BEARING GUIDE

12.7 mm (1/2”) SHANK A

in. TEB 09 B 1/2 1-1/4 TEB 10 B 1/2 1-1/4

CARBIDE TIPPED - TWO FLUTE WITH BALL BEARING GUIDE

12.7 mm (1/2”) SHANK PART No.

B1 B2

B1 mm 31.8 31.8

in. 1 1

PART No.

B2 mm 25.4 25.4

in. 9/32 3/8

TRD 3 B 1/2

C mm 7.1 9.5

in. 3-1/8 3-1/8

A in. .855

B1 mm 21.6

in. 5/8

B2 mm 15.9

in. 7/32

C mm 5.5

in. 2-3/4

mm 70

Replacement Ball Bearing TB8.

mm 79 79

MULTIPLE REED BIT

ACTUAL SIZE

This bit gives a combination of four beads on the material.

B1 B2 CARBIDE TIPPED - TWO FLUTE WITH BALL BEARING GUIDE

PART No. TEB 09 B 1/2

PART No. TEB 10 B 1/2

12.7 mm (1/2”) SHANK A

PART No.

in. TEB 11 B 1/2 1-5/16 TEB 12 B 1/2 1-1/4

B1 mm 33 31.8

in. 1-9/32 1-9/32

B2 mm 32.5 32.5

in. 0.590 3/4

C mm 15 19

in. 3/8 3-1/4

PART No. mm 86 82

TRM 3 B 1/2

A in. .855

B1 mm 21.6

in. 1.16

B2 mm 29.5

in. 7/32

C mm 5.5

in. 3-1/4

mm 82

Replacement Ball Bearing TB8.

Replacement Ball Bearing TB11.

CLASSICAL COMBINATION BITS

ACTUAL SIZE

This combination bit, developed by Carb-I-Tool, will cut a multitude of different shapes. Any part can be selected, multiple passes will also increase variety of shapes. CARBIDE TIPPED - TWO FLUTES WITH BALL BEARING GUIDE

B R R A

12.7 mm (1/2”) SHANK A B C R RADIUS in. mm in. mm in. mm in. mm TCB 50 B 1/2 1-21/32 42 1-3/16 30 3-5/8 92 3/16 4.8 TCB 60 B 1/2 1-21/32 42 1-3/16 30 3-5/8 92 3/16 4.8

PART No. TEB 12 B 1/2

PART No. TEB 11 B 1/2

PART No.

SINGLE REED BIT

BEARING No. TB16 TB14

MULTI FORM COMBINATION BITS

This bit will produce a single bead on the edge of the material. C

CARBIDE TIPPED TWO FLUTE WITH BALL BEARING GUIDE

B2 B1

12.7 mm (1/2”) SHANK

With this combination bit the number of standard mouldings that can be produced is enormous. With multiple passes and a little imagination any number of beautiful mouldings can be produced. CARBIDE TIPPED - TWO FLUTES WITH BALL BEARING GUIDE

B R R A

12.7 mm (1/2”) SHANK PART No. TRS 3 B 1/2

A in. .885

B1 mm 21.6

in. .397

mm 10

in. 7/32

Replacement Ball Bearing TB8.

Tel 0845 2300299

B2 mm 5.5

C in. mm 2-1/2 63.5

A B C in. mm in. mm in. mm TCB 500 B 1/2 1-3/4 44.5 1-5/16 33.3 3-3/4 95 TCB 600 B 1/2 1-3/4 44.5 1-5/16 33.3 3-5/8 92 PART No.

Fax 0870 0117309

R RADIUS BEARING in. mm No. 3/16 4.8 TB16 3/16 4.8 TB14

E-mail sales@datapowertools.co.uk

Premium Quality

EDGE FORMING BITS BEADING BITS A decorative edge bit with pilot for early American furniture making.

Ideal for drop leaf table joints and rounded edges.

TWO FLUTE - WITH PILOT

T T T T T

506 508 510 512 516

in.

E A B

9/16 11/16 13/16 15/16 1-3/16

14.2 17.5 20.6 23.8 30.1

in.

C mm

in.

R RADIUS in. mm

CARBIDE TIPPED 1/2 12.7 1-3/4 9/16 14.3 1-7/8 9/16 14.3 1-7/8 5/8 15.9 2 13/16 20.6 2-1/4

TWO FLUTE - WITH PILOT

6.35 mm (1/4”) SHANK

44.4 47 47 50.8 57.1

3/16 1/4 5/16 3/8 1/2

CARBIDE TIPPED - TWO FLUTES WITH BALL BEARING GUIDE

T T T T T T T T T T T T T T T T T T T T

502 502 504 504 506 506 505 508 508 510 510 512 512 516 516 520 524 528 532 540

in. 5/8 21/32 3/4 13/16 7/8 7/8 7/8 1 1 1-1/8 1-1/8 1-1/4 1-1/4 1-1/2 1-1/2 1-3/4 2 2-1/4 2-1/2 3

in.

9/16 13/16 1-1/16

14.3 20.6 27

in.

C mm

in.

CARBIDE TIPPED 1/2 12.7 1-5/8 9/16 14.2 1-5/8 5/8 15.9 2

41 41 50.8

R RADIUS in. mm 1/8 1/4 3/8

B mm in. 15.9 5/16 16.7 11/32 19 1/2 20.6 7/16 22.2 1/2 22.2 1/2 22.5 7/16 25.4 1/2 25.4 1/2 28.6 1/2 28.6 1/2 31.8 5/8 31.8 5/8 38.1 3/4 38.1 3/4 44.5 7/8 50.8 1 57.1 1-5/64 63.5 1-1/4 76.2 1-15/32

C mm 7.9 8.7 12.7 11.1 12.7 12.7 11.1 12.7 12.7 12.7 12.7 15.9 15.9 19 19 22.2 25.4 27.4 31.8 37.3

in. 1-7/8 1 7/8 2 2 2 2-1/2 2 2 2-1/2 2 2-5/8 2-1/4 2-5/8 2-1/4 2-3/4 3-1/4 3-1/4 3-1/2 3-5/8 3-3/4

mm 47 47 50.8 50.8 50.8 63.5 50.8 50.8 63.5 50.8 67 57.1 67 57.1 70 82 82 89 92 95

3.2 6.35 9.5

This bit is the same as the rounding over bit but has a smaller bearing leaving 1/16” edge bead. Can be converted to rounding over bit by using bearing TB11.

C B R

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4”

B MB B MB B B 1/2 MB B B 1/2 B B 1/2 B B 1/2 B B 1/2 B 1/2 B 1/2 B 1/2 B 1/2 B 1/2

T 604 T 608 T 612

E A

CARBIDE TIPPED - TWO FLUTES WITH BALL BEARING GUIDE

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4”

PART No.

4.8 6.35 7.9 9.5 12.7

Gives extra smooth chatter free cuts due to precise tool geometry. Can be converted to a beading bit by using bearing TB 9.

PART No.

E = 4.8mm (3/16”)

6.35 mm (1/4”) SHANK PART No.

E = 4.8mm (3/16”)

ROUTER BITS

ROUNDING OVER BITS

R RADIUS in. mm 1/16 1.6 5/64 2 1/8 3.2 4 3/16 4.8 3/16 4.8 5 1/4 6.35 1/4 6.35 5/16 7.9 5/16 7.9 3/8 9.5 3/8 9.5 1/2 12.7 1/2 12.7 5/8 15.9 3/4 19 7/8 22.2 1 25.4 1-1/4 31.8

PART No. T T T T T T T T T T T T T T T T T T T T

602 602 604 604 606 606 605 608 608 610 610 612 612 616 616 620 624 628 632 640

B MB B MB B B 1/2 MB B B 1/2 B B 1/2 B B 1/2 B B 1/2 B 1/2 B 1/2 B 1/2 B 1/2 B 1/2

A in. 5/8 21/32 3/4 13/16 7/8 7/8 7/8 1 1 1-1/8 1-1/8 1-1/4 1-1/4 1-1/2 1-1/2 1-3/4 2 2-1/4 2-1/2 3

B mm in. 15.9 5/16 16.7 11/32 19 1/2 20.6 7/16 22.2 1/2 22.2 1/2 22.5 7/16 25.4 1/2 25.4 1/2 28.6 1/2 28.6 1/2 31.8 5/8 31.8 5/8 38.1 3/4 38.1 3/4 44.5 7/8 50.8 1 57.1 1-5/64 63.5 1-1/4 76.2 1-15/32

C mm 7.9 8.7 12.7 11.1 12.7 12.7 11 12.7 12.7 12.7 12.7 15.9 15.9 19 19 22.2 25.4 27.4 31.8 37.3

in. 1-7/8 1-7/8 2 2 2 2-1/2 2 2 2-1/2 2 2-5/8 2-1/4 2-5/8 2-1/4 2-3/4 3-1/4 3-1/4 3-1/2 3-5/8 3-3/4

mm 47 47 50.8 50.8 50.8 63.5 50.8 50.8 63.5 50.8 67 57.1 67 57.1 70 82 82 89 92 95

R RADIUS in. mm 1/16 1.6 5/64 2 1/8 3.2 4 3/16 4.8 3/16 4.8 5 1/4 6.35 1/4 6.35 5/16 7.9 5/16 7.9 3/8 9.5 3/8 9.5 1/2 12.7 1/2 12.7 5/8 15.9 3/4 19 7/8 22.2 1 25.4 1-1/4 31.8

Replacement Ball Bearing TB9

Replacement Ball Bearing TB11

DOUBLE BEADING BITS

ROUND OVER FILLET BITS These bits are very popular for table and bench tops. Profiles are variable by raising or lowering the bit.

A decorative edge bead.

C CARBIDE TIPPED TWO FLUTES WITH BALL BEARING GUIDE

12.7 mm (1/2”) SHANK A

PART No. TEB TEB TEB TEB

01 02 03 04

B B B B

1/2 1/2 1/2 1/2

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4”

A B

in.

BEARING No.

2-1/4 2-1/4 2.80 2.80

57.1 57.1 71.1 71.1

15/16 15/16 15/16 15/16

23.8 23.8 23.8 23.8

3-1/4 3-1/4 3-1/4 3-1/4

82 82 82 82

TB11 TB9 TB11 TB9

CARBIDE TIPPED - TWO FLUTES WITH BALL BEARING GUIDE

R2 R1 A

A B C in. mm in. mm in. mm TB 606 B 1-3/8 35 11/16 17.4 2-1/4 57.1 TB 606 B 1/2 1-3/8 35 11/16 17.4 2-3/4 70 TB 608 B 1/2 1-5/8 41 7/8 22.2 3-1/8 79 PART No.

R1 RADIUS R2 RADIUS in. mm in. mm 3/16 4.8 1/4 6.35 3/16 4.8 1/4 6.35 1/4 6.35 5/16 7.9

Replacement Ball Bearing TB9.

www.datapowertools.co.uk

more than powertools

Premium Quality

ROUTER BITS

EDGE FORMING BITS COVE BITS

DOUBLE BEADING BITS

Used for a drop leaf table joints and decorative edges.

A decorative edge bead. C

CARBIDE TIPPED - TWO FLUTES WITH BALL BEARING GUIDE

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4”

E = 4.8mm (3/16”) TWO FLUTE - WITH PILOT

A A

PART No.

in. TBR 608 B 1-1/4 TBR 608 B 1/2 1-1/4 TBR 616 B 1/2 2

B C mm in. mm in. mm 31.8 17/32 13.3 2 50.8 31.8 17/32 13.3 2-1/2 63.5 50.8 29/32 22.9 3-1/8 79.4

R1 RADIUS R2 RADIUS in. mm in. mm 1/4 6.4 1/8 3.2 1/4 6.4 1/8 3.2 1/2 12.7 1/4 6.35

Replacement Ball Bearing TB9.

TRIPLE BEADING BITS A decorative edge bead. C

R1 B R2 R1

CARBIDE TIPPED - TWO FLUTES WITH BALL BEARING GUIDE

12.7 mm (1/2”) SHANK A

Replacement Ball Bearing TB9.

R1 RADIUS R2 RADIUS in. mm in. mm in. mm in. mm in. mm TT 606 B 1/2 1-3/4 44.4 7/8 22.2 3-1/4 82 3/16 4.8 1/4 6.35 TT 608 B 1/2 2-1/8 54 1-1/16 27 3-1/4 82 1/4 6.35 5/16 7.9

PART No.

BEADING OGEE BITS Produces a decorative edge moulding.

C R1 R2 B R2

CARBIDE TIPPED - TWO FLUTE WITH BALL BEARING GUIDE

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4”

A B C R1 RADIUS R2 RADIUS in. mm in. mm in. mm in. mm in. mm TBO 30 B 1-1/8 28.6 21/32 16.5 2-1/4 57.1 7/64 2.75 1/4 6.35 TBO 30 B 1/2 1-1/8 28.6 21/32 16.5 2-5/8 67 7/64 2.75 1/4 6.35 TBO 35 B 1-3/8 35 7/8 22.2 2-1/2 63.5 3.15 5/16 8 TBO 35 B 1/2 1-3/8 35 7/8 22.2 3 76 3.15 5/16 8 TBO 50 B 1/2 1-7/8 47 1-5/16 33 3-3/8 86 3/16 4.75 1/2 12.7

PART No.

Replacement Ball Bearing TB11.

E A

6.35 mm (1/4”) SHANK A

PART No.

T T T T

706 708 712 716

in.

B mm

in.

C mm

in.

CARBIDE TIPPED 14.2 3/8 9.5 1-5/8 17.5 9/16 14.2 1-7/8 24 5/8 15.9 2 30 13/16 20.6 2

9/16 11/16 15/16 1-3/16

R RADIUS in. mm

mm 41 47 50.8 50.8

3/16 1/4 3/8 1/2

4.8 6.35 9.5 12.7

Up, sheer cutting angle clears chips fast for chatter free accurate routing.

CARBIDE TIPPED - TWO FLUTES WITH BALL BEARING GUIDE

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4” PART No. T T T T T T T T T T T T T

702 704 706 708 708 710 710 712 712 716 716 720 724

B B B B B B B B B B B B B

1/2 1/2 1/2 1/2 1/2 1/2

A in. 5/8 3/4 7/8 1 1 1-1/8 1-1/8 1-1/4 1-1/4 1-1/2 1-1/2 1-3/4 2

B mm 15.9 19 22.2 25.4 25.4 28.6 28.6 31.8 31.8 38.1 38.1 44.5 50.8

in. 5/16 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 5/8 5/8 3/4 7/8

C mm 7.9 12.7 12.7 12.7 12.7 12.7 12.7 12.7 12.7 15.9 15.9 19 22.2

in. 2-3/32 2-3/32 2-3/32 2-3/32 2-1/2 2 2-5/8 2-3/32 2-5/8 2-1/4 2-3/4 3 3-1/4

R RADIUS in. mm 1/16 1.6 1/8 3.2 3/16 4.8 1/4 6.35 1/4 6.35 5/16 7.9 5/16 7.9 3/8 9.5 3/8 9.5 1/2 12.7 1/2 12.7 5/8 15.9 3/4 19

mm 53 53 53 53 63.5 50.8 67 53 67 57.1 70 76 82

Replacement Ball Bearing TB11

CLASSICAL COVE BITS A decorative edge moulding. By fitting the optional TB11 ball bearing the standard cove design can be achieved.

EDGE & DRAW FACE BIT

B C

CARBIDE TIPPED TWO FLUTES WITH BALL BEARING GUIDE

12.7mm (1/2”) SHANK PART No. TEF 01 B 1/2

A in. 2.6

B mm 66

in. .642

C mm 16.3

Replacement Ball Bearing TB11.

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4” PART No.

in. 3

mm 76

CARBIDE TIPPED - TWO FLUTES WITH BALL BEARING GUIDE

in. TC 708 B 1-1/8 TC 708 B 1/2 1-1/8 TC 712 B 1-3/8 TC 712 B 1/2 1-3/8 TC 716 B 1/2 1-5/8

B mm 28.6 28.6 35 35 41

in. .530 .530 .670 .670 3/4

C mm 13.5 13.5 17 17 19

in. 2-1/4 2-1/2 2-1/4 2-3/4 2-3/4

mm 57.1 63.5 57.1 70 70

R RADIUS in. mm 1/4 6.35 1/4 6.35 3/8 9.5 3/8 9.5 1/2 12.7

Replacement Ball Bearing TB9

Tel 0845 2300299

Fax 0870 0117309

E-mail sales@datapowertools.co.uk

Premium Quality

EDGE FORMING BITS DOUBLE COVE BITS

CLASSICAL BITS This versatile bit produces a very decorative moulding used extensively on many furniture and building applications.

B R2 R1

CARBIDE TIPPED - TWO FLUTES WITH BALL BEARING GUIDE

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4” PART No. TDC 706B TDC 706B 1/2 TDC 708B 1/2

A in.

in.

1-1/2 38.1 3/4 1-1/2 38.1 3/4 1-3/4 44.4 7/8

C mm

in.

CARBIDE TIPPED - TWO FLUTES WITH BALL BEARING GUIDE

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4”

R1 RADIUS R2 RADIUS mm in. mm in. mm

PART No.

in. TC 8 B 1-1/8 TC 8 B 1/2 1-1/8

19 2-1/4 57.1 3/16 4.8 1/4 6.35 19 2-3/4 70 3/16 4.8 1/4 6.35 22.2 3 76 1/4 6.35 5/16 7.9

A B

mm 28.6 28.6

in. 1/2 1/2

mm 12.7 12.7

in. 2 2-1/2

R RADIUS in. mm 1/8 3.2 1/8 3.2

mm 50.8 63.5

ACTUAL SIZE

Replacement Ball Bearing TB9

ROUTER BITS

Produces a decorative edge moulding. By fitting the optional TB11 ball bearing a cove effect can be achieved.

TRIPLE COVE BITS Produces a decorative edge moulding or any combination of the three radii can be used. By fitting the optional TB11 ball bearing a different profile can be achieved.

R1 R2

CARBIDE TIPPED - TWO FLUTES WITH BALL BEARING GUIDE

TB9 BEARING FITTED

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4” A

PART No.

in. TC 12 B 1-3/8 TC 12 B 1/2 1-3/8

12.7mm (1/2”) SHANK

PART No. TC 12 B 1/2 TB11 BEARING FITTED

B mm 35 35

in. 5/8 5/8

C mm 15.9 15.9

in. 2-1/4 2-3/4

mm 57.1 70

R RADIUS in. mm 3/16 4.8 3/16 4.8

ACTUAL SIZE

A B C R1 RADIUS R2 RADIUS in. mm in. mm in. mm in. mm in. mm TTC 706B 1/2 1-7/8 47 1 25.4 3-1/4 82 3/16 4.8 1/4 6.35 TTC 708B 1/2 2-1/4 57.1 1-1/8 28.6 3-3/8 86 1/4 6.35 5/16 7.9

PART No.

Replacement Ball Bearing TB9

PROVINCIAL BITS Like so many of Carb-I-Tool’s router bits this bit can be used as illustrated to produce decorative edge mouldings or by using the guide on your machine many combinations of rounds and covers can be achieved.

B PART No. TC 16 B 1/2

CARBIDE TIPPED - TWO FLUTES WITH BALL BEARING GUIDE

B mm 25.4 25.4 31.8 31.8 38.1

in. 0.460 0.460 .560 .560 0.710

C mm 11.7 11.7 14.2 14.2 18

in. 2 2-5/8 2-1/4 2-5/8 2-3/4

mm 50.8 67 57.1 67 70

A in. 15/8

B mm 41

in. 3/4

C mm 19

in. 2-3/4

R RADIUS in. mm 1/4 6.35

mm 70

Replacement Ball Bearing TB11.

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4” in. TCR 8 B 1 TCR 8 B 1/2 1 TCR 12 B 1-1/4 TCR 12 B 1/2 1-1/4 TCR 16 B 1/2 1-1/2

TB9 BEARING FITTED

12.7 mm (1/2”) SHANK R

PART No.

PART No. TC 16 B 1/2 TB11 BEARING FITTED

R RADIUS in. mm 1/8 3.2 1/8 3.2 3/16 4.8 3/16 4.8 1/4 6.35

Replacement Ball Bearing TB11.

TRADITIONAL CLASSICAL BITS This bit produces a traditional style furniture moulding.

CARBIDE TIPPED TWO FLUTE WITH BALL BEARING GUIDE

B1 R

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4”

B2 A

C B

A PART No.

in. TCRA 16 B 1 1/4 TCRA 16 B 1/2 1 1/4 TCRA 32 B 1/2 2

B C mm in. mm in. mm 31.8 19/32 15.0 2-1/4 57.2 31.8 19/32 15.0 2-5/8 66.7 50.8 15/16 23.8 3-1/4 82.6

www.datapowertools.co.uk

R1 RADIUS in. mm 1/4 6.4 1/4 6.4 1/2 12.7

R2 RADIUS in. mm 1/8 3.2 1/8 3.2 1/4 6.35

PART No.

in. TTC 8 B 1 TTC 8 B 1/2 1 TTC 12 B 1-1/4 TTC 12 B 1/2 1-1/4 TTC 16 B 1-1/2 TTC 16 B 1/2 1-1/2

mm 25.4 25.4 31.8 31.8 38.1 38.1

B1 in. mm 7/16 11.1 7/16 11.1 7/16 11.1 7/16 11.1 9/16 14.3 9/16 14.3

B2 in. mm 5/64 2 5/64 2 5/64 2 5/64 2 1/8 3.2 1/8 3.2

C in. 2-1/8 2-1/2 2-1/8 2-9/16 2-1/4 2-3/4

R RADIUS mm in. mm 54 1/8 3.2 63.5 1/8 3.2 54 3/16 4.8 65 3/16 4.8 57.1 1/4 6.35 70 1/4 6.35

Replacement Ball Bearing TB11.

more than powertools

Premium Quality

ROUTER BITS

EDGE FORMING BITS REBATING BITS

CHAMFERING BITS

45¡

Helpful in making almost invisible joints.

E = 4.8mm (3/16”) TWO FLUTES - WITH PILOT

B E A

450 CHAMFER

E = 4.8mm (3/16”) TWO FLUTES - WITH PILOT

6.35 mm (1/4”) SHANK A

PART No.

in. 1-1/8

B mm

in.

CARBIDE TIPPED 28.6 11/16 17.4

A popular method of removing sharp corners for a professional finish.

2-1/4

PART No.

Angle from vertical

CARBIDE TIPPED - TWO FLUTES WITH BALL BEARING GUIDE

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4”

A in.

57.1

C B2

1/4 3/8

B mm

in.

C mm

in.

CARBIDE TIPPED 6.35 7/16 11.1 9.5 1/2 12.7

2 2

50.8 50.8

Has ball bearing guide for mar-free finish. Replacement bearing TB-11. By substituting TB-9 bearing the depth of rebate will be increased by 1/16” (1.6mm.)

CARBIDE TIPPED - TWO FLUTES WITH BALL BEARING GUIDE

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4”

B1 B2 C mm in. mm in. mm in. mm 22.50 CHAMFER FROM VERTICAL T 8122 B 1 25.4 21/32 16.5 39/64 15.5 2-1/4 57.1 T 8122 B 1/2 1 25.4 21/32 16.5 39/64 15.5 2-3/4 70 TX 8122 B 1/2 1.42 36 1-1/4 32 28.4 3-1/4 82 300 CHAMFER FROM VERTICAL T 8130 B 1-1/8 28.6 43/64 17 35/64 13.9 2-1/4 57.1 T 8130 B 1/2 1-1/8 28.6 43/64 17 35/64 13.9 2-3/4 70 450 CHAMFER FROM VERTICAL T 916 B 1-3/8 35 5/8 15.9 29/64 11.4 2-1/4 57.1 T 916 B 1/2 1-3/8 35 5/8 15.9 29/64 11.4 2-3/4 70 T 920 B 1/2 1-7/8 47.6 1 25.4 11/16 17.5 2-3/4 70 T 924 B 1/2 2-1/4 57.1 1-1/4 31.8 22.5 3-1/4 82 650 CHAMFER FROM VERTICAL T 8165 B 1.58 40 5/8 15.9 1/4 6.35 2-3/32 53 T 8165 B 1/2 1.58 40 .5/8 15.9 1/4 6.35 2-1/2 63.5 TX 8165 B 1/2 2.95 75 1-3/8 35 14.5 2-3/4 70 800 CHAMFER FROM VERTICAL T 8180 B 1.58 40 9/16 14.3 3/32 2.4 2-1/4 50.8 T 8180 B 1/2 1.58 40 9/16 14.3 3/32 2.4 2-1/2 63.5 TX 8180 B 1/2 2.95 75 1-1/4 32 7/32 5.5 2-9/16 65

in.

Replacement Ball Bearing TB11.

CHAMFERING BIT WITH RADIUS

A in. mm T 1708 B 1/4 6.35 T 1708 B 1/2 1/4 6.35 T 1712 B 3/8 9.5 T 1712 B 1/2 3/8 9.5 TX 1712 B 1/2 3/8 9.5 T 1716 B 1/2 1/2 12.7 Replacement Ball Bearing TB11. T 1720 B 1/2 5/8 15.9 PART No.

B in. 1/2 1/2 1/2 1/2 1 1/2 1/2

C mm 12.7 12.7 12.7 12.7 25.4 12.7 12.7

in. 2 2-1/2 2-1/4 2-1/2 3 9/16 9/16

These bearings can be fitted to the Rebating Bits to give a range of cut depths. PART No. TBS TBS TBS TBS TBS TBS TBS TBS TBS

1 2 3 4 5 6 7 8 9

OD in. 3/4 7/8 1 1 1/8 1 1/4 1 3/8 1 1/2 1 5/8 1 3/4

ID mm 19.0 22.2 25.4 28.6 31.8 34.9 38.1 41.3 44.5

in. 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16

B mm 4.8 4.8 4.8 4.8 4.8 4.8 4.8 4.8 4.8

in. 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16 3/16

B R

TWO FLUTES CARBIDE TIPPED

12.7 mm (1/2”) SHANK

in. TRR 10 B 1/2 1.57 TRR 16 B 1/2 2.4

B mm 40 60.9

in. .458 .530

C mm 11.6 13.5

in. 2-1/2 2-9/16

mm 63.5 65

R RADIUS in. mm .156 3.9 .156 3.9

Replacement Ball Bearing TB11.

Tel 0845 2300299

mm 50.8 63 57 63 76.2 65 65

SHIELDED BEARINGS

80¡

PART No.

C mm

T 1708 T 1712

PART No.

6.35 mm (1/4”) SHANK

T 916

Pilot equipped bits do not require a guide when making rebating cuts.

Fax 0870 0117309

E-mail sales@datapowertools.co.uk

mm 4.8 4.8 4.8 4.8 4.8 4.8 4.8 4.8 4.8

Premium Quality

EDGE FORMING BITS STAIR HANDRAIL BIT C

A time saving bit for rounding over both sides of a board in one pass. CARBIDE TIPPED - TWO FLUTES WITH BALL BEARING GUIDE

B2 B1

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4”

This bit will produce an attractive and functional hand rail for balustrades. It can be used in conjunction with the half bull nose bit to curve the top over. This will produce an optional profile.

ROUTER BITS

BULL NOSE RADIUS BITS

A A

PART No.

in. TBN 2 B 25/32 TBN 2 B 1/2 25/32 TBN 4.5 MB 1/2 51/64 TBN 5 MB 1/2 53/64 TBN 3 B 27/32 TBN 3 B 1/2 27/32 TBN 4 B 29/32 TBN 4 B 1/2 29/32 TBN 6 B 1-1/32 TBN 6 B 1/2 1-1/32 TBN 8 B 1/2 1-5/32 TBN 10 B 1/2 1-9/32 TBN 12 B 1/2 1-13/32 TBN 15 B 1/2 1-21/32 TBN 32 MB 1/2 1-57/64

B1 B2 mm in. mm in. mm 19.8 1/2 12.7 5/32 4 19.8 1/2 12.7 5/32 4 20.4 1/2 12.7 11/64 4.5 20.9 1/2 12.7 13/64 5 21.4 1/2 12.7 7/32 5.5 21.4 1/2 12.7 7/32 5.5 23 3/4 19 9/32 7.1 23 3/4 19 9/32 7.1 26.2 3/4 19 13/32 10.3 26.2 3/4 19 13/32 10.3 29.4 1 25.4 17/32 13.5 32.6 1-3/32 27.8 21/32 16.7 35.8 1-1/4 31.8 25/32 19.8 42 1-1/2 38.1 1-1/32 26.2 48 1-39/64 40.6 1-17/64 32

C in. 2 2-1/2 2-1/2 2-1/2 2 2-1/2 2-3/8 2-3/4 2-3/8 2-3/4 3 3-1/4 3-1/4 3-5/8 3-7/8

mm 50.8 63.5 63.5 63.5 50.8 63.5 60 70 60 70 76 82 82 92 98.4

Replacement Ball Bearing TB8.

TCO 1 B 1/2

TBN 4 B 1/2

C B

PROFILE Use THBN 75 B 1/2 for curved top

CARBIDE TIPPED - TWO FLUTES WITH BALL BEARING GUIDE

12.7 mm (1/2”) SHANK PART No. THR 50 B 1/2

A in. 2

B mm 50.8

in. 2-1/4

C mm 57.1

in. 4.5

mm 116

B mm 22.6 22.6

in. 9/32 9/32

Profile on top of rail can be varied using a half bull nose bit (See diagrams on THR 50 B-1/2).

CARBIDE TIPPED - TWO FLUTES WITH BALL BEARING GUIDE

12.7 mm (1/2”) SHANK

in. 57/64 57/64

OPTIONAL

PROFILE

Replacement Ball Bearing TB8.

Use TBN 4 B or TBN 4 B 1/2 (see above) for matching cutter.

TCO 1 B TCO 1 B 1/2

OPTIONAL

STAIR HANDRAIL BIT

CANOE SLAT BITS

PART No.

C mm 7.1 7.1

in. 1 3/4 2 3/8

mm 44.5 60.3

Replacement Ball Bearing TB11.

PART No.

in. THR 40 B 1/2 2-5/16 THR 60 B 1/2 2-1/8

B mm 58.7 54

in. 2

C mm 38.7 50.8

in. 3-13/16 4.3

mm 96.8 110

Replacement Ball Bearing TB8.

DRAWING LINE BITS

HALF BULL NOSE RADIUS BITS

A popular mould. Common on old style double hung windows, and architraves.

A handy bit for finishing wider timbers. The adjustment of machine height gives a variety of different forms.

B2 B1 CARBIDE TIPPED - TWO FLUTES WITH BALL BEARING GUIDE

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4” PART No. TDL TDL TDL TDL TDL TDL

3 3 4 4 6 6

B B 1/2 B B 1/2 B B 1/2

A in. .850 .850 .910 .910 1.035 1.035

mm 21.6 21.6 23.1 23.1 26.3 26.3

B1 B2

CARBIDE TIPPED - TWO FLUTES WITH BALL BEARING GUIDE

12.7 mm (1/2”) SHANK B1 in. mm 7/16 11.1 7/16 11.1 19/32 15 19/32 15 11/16 17.5 11/16 17.5

Replacement Ball Bearing TB8.

www.datapowertools.co.uk

B2 C in. mm in. mm 7/32 5.5 2 50.8 7/32 5.5 2-1/2 63.5 9/32 7.1 2-3/32 53 9/32 7.1 2-3/4 70 13/32 10.3 2-1/4 57.1 13/32 10.3 2-3/4 70

A A

B2 C R RADIUS PART No. in. mm in. mm in. mm in. mm mm THBN 45 B 1/2 1 25.4 1.18 30 1.41 36 3-5/8 92 45 THBN 60 B 1/2 1-1/16 27 1-5/8 41 1-7/8 47.6 4 102 60 THBN 75 B 1/2 1-1/8 28.6 2 50.8 2-1/4 57.1 4-3/8 111.5 75 Replacement Ball Bearing TB16.

more than powertools

Premium Quality

ROUTER BITS

EDGE FORMING BITS OGEE BITS

ROMAN OGEE BITS A decorative edge bit for early American furniture making.

R R

TWO FLUTE - WITH PILOT

6.35 mm (1/4”) SHANK PART No.

T 5705 T 5708

A in. 3/4 1-1/4

in.

19 31.8

CARBIDE TIPPED 1/2 12.7 1-7/8 3/4 19 2

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4” 47 50.8

5/32 1/4

CARBIDE TIPPED TWO FLUTES WITH BALL BEARING GUIDE

4 6.35

PART No.

in. T 7506 B 1-7/16 T 7506 B 1/2 1-7/16

B mm 36.3 36.3

in. 0.650 0.650

C mm 16.5 16.5

in. 2-1/4 2-5/8

mm 57.1 67

R RADIUS in. mm 3/16 4.8 3/16 4.8

ACTUAL SIZE

R PART No. T7508 B1/2 TB11 BEARING FITTED

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4”

TB9 BEARING FITTED

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4”

in. T 5705 B 1-1/8 T 5705 B 1/2 1-1/8

B R

CARBIDE TIPPED - TWO FLUTES WITH BALL BEARING GUIDE

PART No.

R RADIUS in. mm

These bits produce a decorative form used widely on table and mantle edges. By fitting the optional TB9 ball bearing a 1/16” edge bead can be produced as illustrated.

B mm 28.6 28.6

in. 1/2 1/2

C mm 12.7 12.7

in. 2 2-5/8

R RADIUS in. mm 5/32 4 5/32 4

mm 50.8 67

PART No.

in. T 7508 B 1-5/8 T 7508 B 1/2 1-5/8

B mm 41 41

in. 3/4 3/4

C mm 19 19

in. 2-1/4 2-3/4

mm 57.1 70

R RADIUS in. mm 1/4 6.35 1/4 6.35

ACTUAL SIZE

PART No. T 5705 B1/2

PART No. T 5708 B1/2 PART No. T7512 B1/2 TB11 BEARING FITTED

TB9 BEARING FITTED

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4” PART No.

in. T 5708 B 1-1/2 T 5708 B 1/2 1-1/2 T 5712 B 1/2 2

B mm 38.1 38.1 50.8

in. 3/4 3/4 1

C mm 19 19 25.4

in. 2-3/8 2-3/4 3-3/8

R RADIUS in. mm 1/4 6.35 1/4 6.35 3/8 9.5

mm 60 70 86

12.7 mm (1/2”) SHANK PART No. T 7512 B 1/2

A in. 2-1/8

B mm 54

in. 1

C mm 25.4

in. 3-3/8

mm 86

R RADIUS in. mm 3/8 9.5

Replacement Ball Bearing TB11

SHALLOW ROMAN OGEE BITS

DOUBLE OGEE BITS

This bit will produce a decorative edge moulding.

CARBIDE TIPPED - TWO FLUTE WITH BALL BEARING GUIDE

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4” PART No.

in. TDO 8 B 1-1/4 TDO 8 B 1/2 1-1/4 TDO 12 B 1/2 1-5/8 TDO 16 B 1/2 2

in. .575 .575 .763 .950

C mm 14.6 14.6 19.4 24.1

in. 2-3/16 2-5/8 2-3/4 3

Replacement Ball Bearing TB11

Tel 0845 2300299

mm 55 67 70 76

CARBIDE TIPPED TWO FLUTES WITH BALL BEARING GUIDE

R A

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4”

A B

mm 31.8 31.8 41 50.8

R B R

B1 R B2

R RADIUS in. mm 1/8 3.2 1/8 3.2 3/16 4.8 1/4 6.35

A B1 B2 C R RADIUS in. mm in. mm in. mm in. mm mm 5705 B 1-1/4 32 3/8 9.5 5/32 4 2 50.8 4 5705 B 1/2 1-1/4 32 3/8 9.5 5/32 4 2-3/8 60 4 5708 B 1/2 1-5/8 41 7/16 11.1 1/4 6.35 2-1/2 63.5 6.3 5712 B 1/2 2 50.8 9/16 14.3 3/8 9.5 2-5/8 67 9.5

PART No. TS TS TS TS

Replacement Ball Bearing TB11.

Fax 0870 0117309

E-mail sales@datapowertools.co.uk

Premium Quality

EDGE FORMING BITS BATTEN MOULD BIT C

B2 B1

CARBIDE TIPPED - TWO FLUTES WITH BALL BEARING GUIDE

A A

in. TBM 33 B 1/2 1-1/8

B1 mm 28.6

This versatile assembly enables you to round the top and bottom edges of timber at the same time. Assembly comes with bearing, spacer and washers, which allow you to cut up to 30mm material.

C R R B

CARBIDE TIPPED - FOUR FLUTES WITH BALL BEARING GUIDE

12.7 mm (1/2”) SHANK PART No.

DOUBLE EDGE RADIUS BIT

in. 1.3

12.7 mm (1/2”) SHANK

B2 mm 33

in. 7/8

C mm 22.2

in. 3-5/8

PART No.

mm 92

TDA 194-5 MB 1/2 T 194-5 M LH T 194-5 M RH

Replacement Ball Bearing TB8.

TABLE EDGE BIT WITH RETURN This bit has a return to round over bottom of table for an attractive finish.

A mm 32 32 32

R2 B

Wood Thickness 10 19 22 25 30

A B mm 10-30 Cutter only Cutter only

C mm 90 Cutter only Cutter only

R RADIUS mm 5 5 5

ROUTER BITS

A bit to enable production of batten moulding for the fixing of cement sheeting and other types of wall panelling.

Spaces between cutters nil (no Brg.) Brg. + 2 Washers Brg. + 5 Washers Brg. + Spacer Brg. + Spacer & 5 Washers

Replacement Ball Bearing TB12. Replacement Arbor TA20.

CARBIDE TIPPED - TWO FLUTES WITH BALL BEARING GUIDE

PART No. TEB 15 B 1/2

A in. 2

TABLE EDGE BIT

12.7 mm (1/2”) SHANK B

R1 RADIUS R2 RADIUS mm in. mm in. mm mm mm 50.8 1.150 29.2 3-1/2 89 8 16

A popular bit for finishing table edges.

CARBIDE TIPPED - TWO FLUTES WITH BALL BEARING GUIDE

Replacement Ball Bearing TB11.

SPECIAL B I T S Are made to any size or detail. Please furnish a wood sample or drawing of the detail when ordering.

12.7 mm (1/2”) SHANK PART No. TEB 14B 1/2

A in. 2

A B C R1 RADIUS R2 RADIUS mm in. mm in. mm mm mm 50.8 0.720 18.3 3-1/8 79 8 16

Replacement Ball Bearing TB11.

SOLID SURFACE BITS (i) for use on Corian® or other imitation marble type material (ii) the Delrin® shielded bearings are used to prevent scoring (iii) see page 33 for the range of bearings

COUNTER TOP BIT

B A

NO DRIP DESIGN TWO FLUTES - WITH CARBI-SMOOTH BEARING ASSEMBLY & BALL BEARING GUIDE

A 25.4

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4”

Solid Face Surface Top

B 22.9

PART No. TSS 2 TSS 2 1/2

C 82

Replacement Bearing Assembly TBT21.

Used in conjunction with T S S 2 a n d T S S 2 1/ 2

R Top

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4” B 13.5 13.5

B 9.3 9.3

C 41 54

R RADIUS 6.35 6.35

A C 60 73

Solid Surface Top

R RADIUS 6.35 6.35

Face

15¡

Top Bowl

B PART No. TSS 4 B 1/2

Face

TWO FLUTES - WITH CARBI-SMOOTH BEARING ASSEMBLY & BALL BEARING GUIDE

12.7 mm (1/2”) SHANK

TWO FLUTES - WITH CARBI-SMOOTH BEARING ASSEMBLY & BALL BEARING GUIDE

A 28.6 28.6

A 19 19

BEVEL UNDERMOUNT BOWL BIT

COUNTER TOP BIT

PART No. TSS 3 B TSS 3 B 1/2

NO DRIP DESIGN - TWO FLUTES

12.7 mm (1/2”) SHANK PART No. TSS 1 B 1/2

A 35

B 32

C 88

Replacement Bearing Assembly TBT19.

Replacement Bearing Assembly TBT20.

www.datapowertools.co.uk

more than powertools

Premium Quality

ROUTER BITS

SOLID SURFACE BITS ROMAN OGEE UNDERMOUNT BOWL BIT C

ROUNDING OVER UNDERMOUNT BOWL BIT

R2 B

Top

TWO FLUTES - WITH BALL BEARING GUIDE

12.7 mm (1/2”) SHANK

12.7 mm (1/2”) SHANK R1 5/32

12.7 mm (1/2”) SHANK C 85

Top

TWO FLUTES - WITH CARBI-SMOOTH BEARING ASSEMBLY & BALL BEARING GUIDE

PART No. A B TSS 5 B 1/2 50.8 25.4

Bowl

Bowl TWO FLUTES - WITH CARBI-SMOOTH BEARING ASSEMBLY & BALL BEARING GUIDE

BULLNOSE BIT SET. INVERTED ROUNDING OVER BIT

PART No. TSS 6 B 1/2

R2 3/8

A 44.5

B 25.4

C 85

R RADIUS 9.5

PART No. TSS 7 B 1/2 TSS 9 B 1/2

A 60.3 66.7

B 22.2 24.1

Replacement Bearing Assembly TBT19.

Replacement Bearing TB18.

ROUNDING OVER BIT

FACE INLAY BIT

SURFACE PLANER

1/4” WIDTH-1/2” WIDTH

C 80 82

R RADIUS 16 19

C C C B

B A

Face

Top Bo

TWO FLUTES - WITH CARBI-SMOOTH BEARING ASSEMBLY & BALL BEARING GUIDE

12.7 mm (1/2”) SHANK TWO FLUTES - WITH CARBI-SMOOTH BEARING ASSEMBLY & BALL BEARING GUIDE

Replacement Bearing Assembly TBT20.

PART No. TSS 11 B 1/2 TSS 21 B 1/2 TSS 31 B 1/2 TSS 12 B 1/2 TSS 22 B 1/2 TSS 32 B 1/2

CHAMFER BIT 15°

BOWL CUTTER 15°

12.7 mm (1/2”) SHANK PART No. TSS 8 B 1/2 TSS 10 B 1/2

A 47.6 54

B 20.6 25.4

C 80 84

R RADIUS 16 19

B 1/4” 1/4” 1/4” 1/2” 1/2” 1/2”

C 66 66 66 73 73 72

G 1.6 3.2 4.8 1.6 3.2 4.8

BRG TB14 TB11 TB11 TB11 TB11 TB11

TWO FLUTES - WITH BALL BEARING GUIDE

B 25.4

C 80

12.7mm (1/2”) SHANK

15¡

PART No. TSS 15 B 1/2

C 85

A 28.6

Solid Surface Top B 25.4

Replacement Ball Bearing TB18.

BEVEL BIT

OVERHANG TRIM BIT

C 85

PART No. TSS 16 1/2

A 23.8

B 9.5

C 54

FLUSH TRIM BIT

15¡ CARBIDE TIPPED TWO FLUTE

12.7mm (1/2”) SHANK

A B 32

B 9.5

Replacement Ball Bearing TB18.

A 25.4

A 50.8

12.7 mm (1/2”) SHANK

A A 28.6

PART No. TSS 13 1/2

CARBIDE TIPPED TWO FLUTE

Bowl

PART No. TSS 14 B 1/2

12.7 mm (1/2”) SHANK

Top

12.7 mm (1/2”) SHANK

SIX FLUTES

COUNTER TOP BIT

TWO FLUTES WITH BALL BEARING GUIDE

PART No. TSS 17 1/2

BRG ASS TBT 22 TBT 21 TBT 20 TBT 22 TBT 21 TBT 20

15¡

A 25.4 25.4 25.4 25.4 25.4 25.4

C 68

Tel 0845 2300299

CARBIDE TIPPED TWO FLUTE WITH CARBI-SMOOTH BEARING ASSEMBLY& BALL BEARING GUIDE

A 19

B 25.9

12.7mm (1/2”) SHANK

12.7mm (1/2”) SHANK PART No. TSS 18 B 1/2

CARBIDE TIPPED - TWO FLUTE WITH CARBI-SMOOTH BEARING ASSEMBLY & BALL BEARING GUIDE

A PART No. TSS 19 B 1/2

C 87

Replacement Bearing Assembly TBT19. Replacement Ball Bearing TB7.

Fax 0870 0117309

A 19

B 25.9

C 87

Replacement Bearing Assembly TBT21. Replacement Ball Bearing TB7.

E-mail sales@datapowertools.co.uk

Premium Quality

FACE MOULDING BITS Face moulding bits can be used for window sills, architraves, picture frames or handrails.

FACE MOULDING BIT

B CARBIDE TIPPED - TWO FLUTES WITH BALL BEARING GUIDE

12.7mm (1/2”) SHANK PART No. TFM 01 B 1/2

A1 in. -

mm 17.8

A2 in. mm 1-1/4 31.8

B in. mm 1-5/16 33

B CARBIDE TIPPED - TWO FLUTES WITH BALL BEARING GUIDE

A1 A2

12.7mm (1/2”) SHANK

C in. mm 3-3/8 86

ROUTER BITS

FACE MOULDING BIT

PART No.

in. TFM 03 B 1/2 1/2

A2 mm 12.7

in. 1-1/4

B mm 31.8

in. 1-5/16

C mm 33

in. 3-3/8

mm 86

Replacement Ball Bearing TB11.

Replacement Ball Bearing TB8.

FACE MOULDING BIT

B B CARBIDE TIPPED - TWO FLUTES WITH BALL BEARING GUIDE

CARBIDE TIPPED - TWO FLUTES WITH BALL BEARING GUIDE

12.7mm (1/2”) SHANK

PART No. PART No. TFM 06 B 1/2

A in. 0.945

B mm 24

in. 1-7/16

C mm 36.5

12.7mm (1/2”) SHANK

in. 3-1/2

mm 89

TFM 12 B 1/2

A in. 0.945

B mm 24

in. 1-7/16

C mm 36.5

in. 3-1/2

mm 89

Replacement Ball Bearing TB8.

FACE MOULDING BIT

C B

CARBIDE TIPPED - TWO FLUTES WITH BALL BEARING GUIDE

12.7mm (1/2”) SHANK PART No.

CARBIDE TIPPED - TWO FLUTES WITH BALL BEARING GUIDE

TFM 24 B 1/2

12.7mm (1/2”) SHANK PART No. TFM 18 B 1/2

B mm 24

in. 0.945

B mm 24

in. 1-7/8

C mm 47.9

in. 4

mm 102

Replacement Ball Bearing TB8.

A in. 0.945

in. 1-7/16

C mm 36.5

in. 3-1/2

mm 89

FACE MOULDING BIT

Replacement Ball Bearing TB8.

FACE MOULDING BIT

B C CARBIDE TIPPED - TWO FLUTES WITH BALL BEARING GUIDE

12.7mm (1/2”) SHANK B CARBIDE TIPPED - TWO FLUTES WITH BALL BEARING GUIDE

TFM 32 B 1/2

TFM 30 B 1/2

A in. 1-3/4

B mm 44.5

in. 1-1/2

in. 4

B mm 44.4

in. 1-7/8

C mm 48

in. 4-1/8

mm 105

C mm 38.1

A in. 1-3/4

Replacement Ball Bearing TB8.

12.7mm (1/2”) SHANK PART No.

PART No.

mm 102

Replacement Ball Bearing TB12.

www.datapowertools.co.uk

more than powertools

Premium Quality

ROUTER BITS

FACE MOULDING BITS Face moulding bits can be used for window sills, architraves, picture frames or handrails.

FACE MOULDING BIT

FACE MOULDING BIT C

B B

CARBIDE TIPPED - TWO FLUTES WITH BALL BEARING GUIDE

12.7mm (1/2”) SHANK PART No. TFM 36 B 1/2

A in. 1-1/2

B mm 38.1

12.7mm (1/2”) SHANK in. 1-5/8

C mm 41.3

in. 3-5/8

PART No.

mm 92

TFM 42 B 1/2

Replacement Ball Bearing TB8.

A in. 1-1/2

B mm 38.1

in. 1-5/8

C mm 41.3

in. 3-5/8

mm 92

Replacement Ball Bearing TB8.

FACE MOULDING BIT

CARBIDE TIPPED - TWO FLUTES WITH BALL BEARING GUIDE

TFM 48 B 1/2

A in. 1-1/4

B mm 31.8

CARBIDE TIPPED - TWO FLUTES WITH BALL BEARING GUIDE

12.7mm (1/2”) SHANK PART No.

in. 1-5/8

12.7mm (1/2”) SHANK C

mm 41.3

in. 3-5/8

PART No.

mm 92

TFM 54 B 1/2

A in. 1-1/8

B mm 28.6

Replacement Ball Bearing TB8.

FACE MOULDING BIT

A in. 1-5/8

C mm 41.3

in. 3-5/8

mm 92

CARBIDE TIPPED - TWO FLUTES WITH BALL BEARING GUIDE

12.7mm (1/2”) SHANK PART No. TFM 60 B 1/2

A in. 1-5/8

B mm 41.3

CARBIDE TIPPED - TWO FLUTES WITH BALL BEARING GUIDE

in. 1-3/4

C mm 44.5

12.7mm (1/2”) SHANK

in. 3-7/8

PART No.

mm 98

TFM 66 B 1/2

Replacement Ball Bearing TB8.

A in. 1-1/8

B mm 28.6

in. 2-1/4

C mm 57.1

in. 4-3/8

mm 111.5

Replacement Ball Bearing TB8.

FACE MOULDING BIT

B B

CARBIDE TIPPED - TWO FLUTES WITH BALL BEARING GUIDE

PART No. TFM 72 B 1/2

A in. 1-1/8

B mm 28.6

in. 2-1/4

C mm 57.1

Replacement Ball Bearing TB8.

12.7mm (1/2”) SHANK

Tel 0845 2300299

in. 4-3/8

mm 111.5

PART No. TFM 80 B 1/2

A in. 1-1/4

B mm 31.8

in. 2-1/4

C mm 57.1

in. 4-3/8

Replacement Ball Bearing TB8.

Fax 0870 0117309

E-mail sales@datapowertools.co.uk

mm 111.5

Premium Quality

FACE MOULDING BITS SINGLE REGENCY BIT

A decorative face mould to highlight the ends of protruding boards such as mantle supports.

B2 B1

CARBIDE TIPPED - TWO FLUTE WITH BALL BEARING GUIDE

B2 B1

CARBIDE TIPPED - TWO FLUTE WITH BALL BEARING GUIDE

PART No. TDR 33 B 1/2

A in. 3/4

B1 in. mm 1-5/16 33

mm 19

B2 in. 1

C mm 25.4

12.7mm (1/2”) SHANK

12.7mm (1/2”) SHANK in. 3-3/8

PART No.

mm 86

in. TSR 33 B 1/2 15/16

Replacement Ball Bearing TB8.

B1 mm 23.5

in. 1-5/16

B2 mm 33

in. 23/32

mm 18.3

in. 3-5/8

mm 92

ROUTER BITS

DOUBLE REGENCY BIT

Replacement Ball Bearing TB8.

SURFACE BEADING BIT C

A decorative face mould to highlight the ends of protruding boards, such as mantle supports.

Carb-I-Tool has an ongoing program to improve and update its product range. Carb-I-Tool (Aust.) Pty. Ltd. therefore reserves the right to change specifications where necessary.

B2 B1

CARBIDE TIPPED - TWO FLUTE WITH BALL BEARING GUIDE

12.7mm (1/2”) SHANK PART No. TSB 33 B 1/2

A in. 3/4

B1 in. mm 1-5/16 33

mm 19

B2 in. 5/8

C mm 15.9

in. 3-3/8

mm 86

Replacement Ball Bearing TB8.

FINGER JOINT BITS Produces a very strong joint due to the extended glue line. Supplied with five, finger slot cutters, which are removable allowing for a range of joint thickness.

5 C UTTERS

Designed to join large boards, as well as making spine and scarf, mortise and tenon joints. Supplied with three, 2-wing cutters as shown, additional cutter may be added if needed. For use with router table.

8.7mm

B 12.7mm A W OOD T HICKNESS : 31-36mm

CARBIDE TIPPED TWO WING

CARBIDE TIPPED -

12.7mm (1/2”) SHANK

4 C UTTERS

12.7mm (1/2”) SHANK

3 C UTTERS 2 C UTTERS 1 C UTTER

PART No. TAFJ 60 1/2 TFG 60

W OOD T HICKNESS :

PART No. TAFJ 90 B 1/2 TFJS 90 TFJE 90

11-16mm

16-21mm

A in.

21-26mm

B mm 40 40 39.6

in.

26-31mm

A in. 2-1/2 2-1/2

B mm 63.5 63.5

in. 15/16 11/32

mm 23.8 8.7

C in. mm 3-5/8 92 Cutter only

Replacement Arbor TA21

mm in. 30 3-7/8 Finger Slot Cutter Abutting Edge Cutter

mm 98.6

® Replacement Ball Bearing TB 3 Replacement Arbor TFJA90

www.datapowertools.co.uk

more than powertools

Premium Quality

JOINING BITS

ROUTER BITS

TONGUE AND GROOVE BITS

MITRE LOCK BIT

This bit makes professional hard to detect tongue and groove joints. One bit only is required, simply invert second piece of timber for matching joints.

Primarily designed for joining material at 90o, however this bit will also produce reasonably strong straight joints. One bit is required. For 900 joins cut second piece of timber at 900 to first piece to produce joint. For straight joints invert the second piece of timber for matching joint.

B A CARBIDE TIPPED - TWO FLUTES STYLE A - Tongue & Groove Joint

12.7mm (1/2”) SHANK A

C T Min. T Max. in. mm in. mm in. mm in. mm in. mm TGA 100 1/2 1-3/4 44.5 1-5/32 29.4 3-1/8 79 15/32 12 1-9/64 29 PART No.

90° JOINTS

CARBIDE TIPPED TWO FLUTES

STRAIGHT JOINTS

12.7mm (1/2”) SHANK A B in. mm in. mm TML 60 1/2 2-3/8 60.3 61/64 24.2

PART No.

in. 3

mm 76

T Min. mm 8.7

T Max. mm 20

STYLE A

DRAW JOINT BIT

CARBIDE TIPPED TWO FLUTES STYLE B - Tongue & Groove Joint

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4”.

STYLE B

This bit is very easy to use for quick joining. It gives you the option to create a plain or rebated drawer by varying the depth of cut. WOOD THICKNESS MIN.: 10 mm for X MIN.: 15 mm for Y

B 15¡

A B C T Min. T Max. in. mm in. mm in. mm in. mm in. mm 50 1.180 30 63/64 25 2-1/4 57.1 7/16 11.1 7/8 22.2 50 1/2 1.180 30 63/64 25 2-1/4 57.1 7/16 11.1 7/8 22.2 100 1/2 1-3/4 44.4 1-5/32 29.4 3-1/4 82 5/8 15.9 1-1/32 27.8 200 1/2 1-3/4 44.4 2 50.8 4 102 11/16 17.5 1-15/16 49.2

PART No. TGB TGB TGB TGB

CARBIDE TIPPED TWO FLUTES

12.7mm (1/2”) SHANK PART No.

TONGUE AND GROOVE BIT for wall panel

TGD 35 1/2

REBATE

PLAIN

A in. 1-3/8

B mm 35

in. .768

C mm 19.5

in. 2-1/2

mm 63.5

JOINTING BIT

WOOD THICKNESS MIN.: 10 mm MAX.: 45 mm

B T

TTG 10 1/2 To cut matching piece remove slotting cutter and add spacer supplied

PART No.

in. TTG 10 1/2 1-5/8 TTGR 10 1-1/8 TTGS 10 1-5/8 TTGC 10 1-5/8 TTGW 10

B C T Min. T Max. mm in. mm in. mm in mm in mm 41.3 1 25.4 3-1/8 79.4 15/32 12.0 13/16 20.6 28.6 10.5 Cutter only 41.3 4 Slot cutter 41.3 27/64 10.8 Bevel cutter Spacer

Replacement Arbor TA14

Tel 0845 2300299

CARBIDE TIPPED TWO FLUTES

12.7mm (1/2”) SHANK

PART No. TGC 100 1/2

Fax 0870 0117309

A in. 1-3/4

B mm 44.4

in. 1-7/8

C mm 47

in. 3-7/8

E-mail sales@datapowertools.co.uk

mm 98

Premium Quality

D O O R PA N E L B I T S FOR BOTH RAIL AND STILE The TPD 1B-1/2 and TPD 2-1/2 are manufactured as matched sets in order that the rail and stile fit together as perfect joints. The TPD 1B-1/2 now has a ball bearing guide ensuring simpler set ups for professional results. Arches on your cupboard doors are now much easier to achieve.

ROUTER BITS

REVERSIBLE PANEL DOOR BITS

PANEL DOOR BITS

1/4"

C 1-5/8" B A A RAIL STILE

CARBIDE TIPPED - TWO FLUTES WITH BALL BEARING GUIDE

PANEL

Replacement Ball Bearing TB12 Replacement Grooving Cutter TPDG 9 Replacement Arbor TA6

Perspective View of Panel Door (with one rail removed).

PANEL GROOVE: 4 mm

STILE RAIL

CARBIDE TIPPED TWO FLUTES TWO BIT SET

12.7mm (1/2”) SHANK PART No. TPD 1 B 1/2 TPD 2 1/2

A mm 55 54

C mm 94 76

Wood Thickness Min: 16mm Max: 20mm

YOUR CHOICE OF ANY COMPLETE PROFILE ASSEMBLIES PROFILER

B mm 29 25

ALTERNATIVE USE

PART No. TPDR 10 B 1/2

STILE

PART NUMBERS STACKED COMMON REVERSIBLE STILE AND PROFILE RAIL CUTTER

OGEE WOOD THICKNESS MIN:20 mm MAX: 25 mm

TPDR 10 B 1/2

TPDS 10 B 1/2

TPDC 10

TPDR 11 B 1/2

TPDS 11 B 1/2

TPDC 11

TPDR 12 B 1/2

TPDS 12 B 1/2

TPDC 12

TPDR 13 B 1/2

TPDS 13 B 1/2

TPDC 13

Replacement Ball Bearing TB17.

CLASSICAL

STACKED STILE AND RAIL ASSEMBLIES Now you can machine stile and rail with just one bit without having to adjust and switch, reverse or remove the bit from your router. Designed for use in your router table, this bit will machine 16mm to 20mm material. Ball bearing guide allows you to do odd shapes such as arches or cathedral pattern doors. Assembly feature allows any cutter to be removed for economical repair, sharpening, or replacement. Also makes glass door and tongue and groove joints. TWO FLUTE, CARBIDE TIPPED, BALL BEARING GUIDE

TRADITIONAL

1/4" STRAIGHT

1-5/8" PART No. TPDS 11 B 1/2

11mm STEP 1. Cut the Stile

Stile and Rail STEP 2. Cut the Rail

® Replacement Ball Bearing TB12, Replacement grooving Cutter TPDG 9. Replacement Arbor TA20

www.datapowertools.co.uk

more than powertools

Premium Quality

ROUTER BITS

PA N E L D O O R & W I N D O W B I T S PANEL DOOR BITS

WINDOW SASH & RAIL BITS These two bits work together to produce a complete divided light sash. The TCW 2B 1/2 is used to cope the rails, sash bars, and muntins. The TCW 1B 1/2 cuts the profile on all components. Application: Cuts all composition materials, plywood, hard wood, and soft wood. Use on table mounted portable routers.

4mm

WOOD THICKNESS MIN:16 mm MAX: 20 mm

A C

CARBIDE TIPPED - TWO FLUTES

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4”. PART No. TPS 8 B-1 TPS 8 B 1/2-1 TPSG 8

A in. 1-3/8 1-3/8 1-3/8

B mm 35 35 35

in. 17/32 17/32

C mm 13.5 13.5 Cutter

in. 2-1/2 2-7/8 only

mm 63.5 73

R RADIUS mm 8 8 -

R R B 16mm

R R

Replacement Ball Bearing TB14 Replacement Grooving Cutter - TPSG 8

A C

R B

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4”. PART No. TPS 8-2 TPS 8 1/2-2

12.7mm (1/2”) SHANK A PART No. A

in. 1-3/8 1-3/8

B mm 35 35

in. 7/8 7/8

C mm 22.2 22.2

in. 2-1/4 2-5/8

mm 57.1 67

R RADIUS mm 8 8

TCW 1B 1/2 TCW 2B 1/2 TCW 3

A in. 1.654 1.654 1.654

B mm 42 42 42

in. 1-1/2 .609

C in. mm 3.55 90.1 2.77 70.5 Cutter only

mm 38.1 15.5

R RADIUS in. mm .200 5.08 .200 5.08

Replacement Ball Bearing TB12

R A I S E D PA N E L D O O R B I T S RAISED PANEL BITS

PANEL BITS WIDE FLAT BOTTOM

This bit produces an Ogee Fillet on panel doors and draw fronts.

Specially designed for grooving panel doors. Bevel

CARBIDE TIPPED - TWO FLUTES

12.7mm 1/2” SHANK

A2 A1 CARBIDE TIPPED - TWO FLUTES

A A

PART No.

in. TOG 57 B 1/2 2-1/4 TOG 67 B 1/2 2-1/4

B mm 57 57

in. 3/4 3/4

C mm 19 19

in. 3 3

mm 76 76

2-3/4

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4”. BEARING No. TB11 TB9

Also available without Ball Bearing

TOG 57 1/2

2-1/4

3/4

NO BEARING

ELLIPTICAL BEADING BITS WIDE FLAT BOTTOM

TE 808 1/2 TE 812 1/2

B mm 30.5 31.8

in. 7/16 9/16

12.7mm (1/2”) SHANK A

C mm 11 14.2

in. 3/8 3/8 1/2 1/2

A2 mm 9.5 9.5 12.7 12.7

B in. mm 7/16 11 7/16 11 9/16 14.3 9/16 14.3

C in. 1-5/8 2-1/8 1-13/16 2-5/16

mm 41 54 46 58.5

25° 25° 25° 25°

This bit is used for panel doors and other decorative edges.

in. 2-7/16 2-9/16

mm 62 65

R RADIUS in. mm 3/8 9.5 3/8 9.5

CARBIDE TIPPED - TWO FLUTES WITH BALL BEARING GUIDE

Bevel

12.7mm (1/2”) SHANK A1 in. mm TRP 40 B 1/2 1-5/8 40 PART No.

B A2 A1

A2 in. 1/8

B mm 3.2

in. 1/2

C mm in. mm 12.7 2-5/8 67

Replacement Ball Bearing TB11.

BEVEL

CARBIDE TIPPED - TWO FLUTES

in. 1-3/64 1-1/4

A1 in. mm TPD 25 1 25.4 TPD 25 1/2 1 25.4 TPD 50 1.575 40 TPD 50 1/2 1.575 40 PART No.

RAISED PANEL BIT

Specially designed for grooving panel doors.

PART No.

Tel 0845 2300299

Fax 0870 0117309

E-mail sales@datapowertools.co.uk

BEVEL 25°

Premium Quality

R A I S E D PA N E L B I T S RAISED PANEL BITS Also available with a ball bearing guide.

CARBIDE TIPPED TWO FLUTES

B B

12.7mm (1/2”) SHANK PART No. TPD 3 1/2 TPD 3 B 1/2

CARBIDE TIPPED - TWO FLUTES

A in. 2.83 2.83

B mm 72 72

in. 5/8 5/8

12.7mm (1/2”) SHANK

C mm 15.9 15.9

in. 2-3/4 3

mm 70 76

PART No. TPDV 3 1/2

A in. 1.36

B mm 34.5

in. 1.7

C mm 43

in. 3-5/8

mm 92

ROUTER BITS

VERTICAL RAISED PANEL BIT

Replacement Ball Bearing TB11.

VERTICAL RAISED PANEL BIT

RAISED PANEL BITS Also available with a ball bearing guide.

C B

CARBIDE TIPPED TWO FLUTES

PART No. TPD 4 1/2 TPD 4 B 1/2

A in. 2-3/8 2-3/8

B mm 60.3 60.3

in. 5/8 5/8

12.7mm (1/2”) SHANK PART No.

C mm 15.9 15.9

in. 2-3/4 3

mm 70 76

TPDV 4 1/2

Replacement Ball Bearing TB11.

B mm 28.6

in. 1-1/2

C mm 38.1

mm 89

C B 25¡

CARBIDE TIPPED TWO FLUTES

B CARBIDE TIPPED - TWO FLUTES

12.7mm (1/2”) SHANK

B mm 76.2 76.2

in. 5/8 5/8

TPDV 5 1/2

C mm 15.9 15.9

12.7mm (1/2”) SHANK PART No.

in. 3 3

in. 3-1/3

Also available with a ball bearing guide.

TPD 5 1/2 TPD 5 B 1/2

A in. 1-1/8

VERTICAL RAISED PANEL BIT

RAISED PANEL BITS

PART No.

CARBIDE TIPPED - TWO FLUTES

12.7mm (1/2”) SHANK

in. 2-3/4 2-3/4

mm 70 70

A in. 1-1/4

B mm 31.8

in. 1-1/2

C mm 38.1

in. 3-1/3

mm 89

VERTICAL RAISED PANEL BIT

Replacement Ball Bearing TB11.

RAISED PANEL BITS Also available with a ball bearing guide. B C CARBIDE TIPPED TWO FLUTES

CARBIDE TIPPED - TWO FLUTES

12.7mm (1/2”) SHANK PART No. TPD 6 1/2 TPD 6 B 1/2

PART No. A A in. 3 3

TPDV 6 1/2

B mm 76 76

in. 5/8 5/8

12.7mm (1/2”) SHANK A in. 1-1/8

B mm 28.6

in. 2

C mm 50.8

in. 3-7/8

mm 98

C mm 15.9 15.9

in. 2-3/4 3

mm 70 76

Replacement Ball Bearing TB11.

www.datapowertools.co.uk

more than powertools

Premium Quality

ROUTER BITS

SLOTTING CUTTERS ASSEMBLIES ASSEMBLIES

ASSEMBLIES

By using the guide on your routing machine, the maximum depth of cut can be obtained.

Ball bearing guide eliminates the cumbersome and time consuming job of setting up router machine guides.

B 50.8mm 19 mm max depth

SLOTTING CUTTER ONLY B

50.8mm 14.4 mm max depth

CARBIDE TIPPED - TWO FLUTES

CARBIDE TIPPED - TWO FLUTES WITH BALL BEARING GUIDE

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4”

PART No. TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA

in. 1/16 1/16 5/64 5/64 3/32 3/32 7/64 7/64 1/8 1/8 9/64 9/64 5/32 5/32 3/16 3/16 7/32 7/32 1/4 1/4

500-1.6 M 500-1.6 M 1/2 500-2 M 500-2 M 1/2 500-2.5 M 500-2.5 M 1/2 500-2.8 M 500-2.8 M 1/2 500-3.2 M 500-3.2 M 1/2 500-3.6 M 500-3.6 M 1/2 500-4 M 500-4 M 1/2 500-4.8 M 500-4.8 M 1/2 500-5.5 M 500-5.5 M 1/2 500-6.4 M 500-6.4 M 1/2

ARBOR mm 1.6 1.6 2 2 2.5 2.5 2.8 2.8 3.2 3.2 3.6 3.6 4 4 4.8 4.8 5.5 5.5 6.4 6.4

TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA

15 16 15 16 15 16 15 16 15 16 15 16 15 16 15 16 15 16 15 16

PART No. TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA

500-1.6 MB 500-1.6 MB 1/2 500-2 MB 500-2 MB 1/2 500-2.5 MB 500-2.5 MB 1/2 500-2.8 MB 500-2.8 MB 1/2 500-3.2 MB 500-3.2 MB 1/2 500-3.6 MB 500-3.6 MB 1/2 500-4 MB 500-4 MB 1/2 500-4.8 MB 500-4.8 MB 1/2 500-5.5 MB 500-5.5 MB 1/2 500-6.4 MB 500-6.4 MB 1/2

B in. 1/16 1/16 5/64 5/64 3/32 3/32 7/64 7/64 1/8 1/8 9/64 9/64 5/32 5/32 3/16 3/16 7/32 7/32 1/4 1/4

Replacement and additional cutters can be purchased singularly for economy where you have an existing arbor.

ARBOR mm 1.6 1.6 2 2 2.5 2.5 2.8 2.8 3.2 3.2 3.6 3.6 4 4 4.8 4.8 5.5 5.5 6.4 6.4

TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA

4 5 4 5 4 5 4 5 4 5 4 5 4 5 4 5 4 5 4 5

A CARBIDE TIPPED - TWO FLUTES

CUTTER BORE 8mm (5/16”)

PART No. T T T T T T T T T T

500-1.6 M 500-2 M 500-2.5 M 500-2.8 M 500-3.2 M 500-3.6 M 500-4 M 500-4.8 M 500-5.5 M 500-6.4 M

A in. 2 2 2 2 2 2 2 2 2 2

B mm 50.8 50.8 50.8 50.8 50.8 50.8 50.8 50.8 50.8 50.8

in. 1/16 5/64 3/32 7/64 1/8 9/64 5/32 3/16 7/32 1/4

mm 1.6 2 2.5 2.8 3.2 3.6 4 4.8 5.5 6.35

Replacement Ball Bearing TB12.

ASSEMBLIES

Bits without bearings can be used where the bearing and nut interfere with the work piece configuration.

Four flute bits with ball bearing guide produce an accurate and professional job with minimum set up time.

SLOTTING CUTTER ONLY B

B 50.8mm 19 mm max depth CARBIDE TIPPED - FOUR FLUTES FOR TX CUTTERS MAX DEPTH 30mm.

TA 700-1.6 M TA 700-1.6 M 1/2 TA 700-2 M TA 700-2 M 1/2 TA 700-2.5 M TA 700-2.5 M 1/2 TA 700-2.8 M TA 700-2.8 M 1/2 TA 700-3.2 M TA 700-3.2 M 1/2 TA 700-3.6 M TA 700-3.6 M 1/2 TA 700-4 M TA 700-4 M 1/2 TA 700-4.8 M TA 700-4.8 M 1/2 TXA 700-4.8 M 1/2 TA 700-5.5 M TA 700-5.5 M 1/2 TXA 700-5.5 M 1/2 TA 700-6.4 M TA 700-6.4 M 1/2 TXA 700-6.4 M 1/2 TXA 700-8 M 1/2

in. 1/16 1/16 5/64 5/64 3/32 3/32 7/64 7/64 1/8 1/8 9/64 9/64 5/32 5/32 3/16 3/16 3/16 7/32 7/32 7/32 1/4 1/4 1/4 5/16

ARBOR mm 1.6 1.6 2 2 2.5 2.5 2.8 2.8 3.2 3.2 3.6 3.6 4 4 4.8 4.8 4.8 5.5 5.5 5.5 6.4 6.4 6.4 8

50.8mm CARBIDE TIPPED 14.4 mm max depth FOUR FLUTES WITH BALL BEARING GUIDE FOR TX CUTTERS MAX DEPTH 29mm.

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4”

SUFFIX 1/2 = 1/2” SHANK, OTHERWISE 1/4” PART No.

Four flute cutters are used for extra smooth cutting and smoother finishes with longer tool life between sharpenings.

TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA

15 16 15 16 15 16 15 16 15 16 15 16 15 16 15 16 8 15 16 8 15 16 8 8

Tel 0845 2300299

Repl. Ball Bearing TB12 for 14.4mm max depth Repl. Ball Bearing TB13 for 13.4mm max depth

PART No. TA 700-1.6 MB TA 700-1.6 MB 1/2 TA 700-2 MB TA 700-2 MB 1/2 TA 700-2.5 MB TA 700-2.5 MB 1/2 TA 700-2.8 MB TA 700-2.8 MB 1/2 TA 700-3.2 MB TA 700-3.2 MB 1/2 TA 700-3.6 MB TA 700-3.6 MB 1/2 TA 700-4 MB TA 700-4 MB 1/2 TA 700-4.8 MB TA 700-4.8 MB 1/2 TXA 700-4.8 MB 1/2 TA 700-5.5 MB TA 700-5.5 MB 1/2 TXA 700-5.5 MB 1/2 TA 700-6.4 MB TA 700-6.4 MB 1/2 TXA 700-6.4 MB 1/2 TXA 700-8 MB 1/2

B in. 1/16 1/16 5/64 5/64 3/32 3/32 7/64 7/64 1/8 1/8 9/64 9/64 5/32 5/32 3/16 3/16 3/16 7/32 7/32 7/32 1/4 1/4 1/4 5/16

ARBOR mm 1.6 1.6 2 2 2.5 2.5 2.8 2.8 3.2 3.2 3.6 3.6 4 4 4.8 4.8 4.8 5.5 5.5 5.5 6.4 6.4 6.4 8

Fax 0870 0117309

TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA

4 5 4 5 4 5 4 5 4 5 4 5 4 5 4 5 7 4 5 7 4 5 7 7

B A CARBIDE TIPPED - FOUR FLUTES

CUTTER BORE 8 mm (5/16”) TX SERIES: BORE 12.7 mm (1/2”)

PART No. T 700-1.6 M T 700-2 M T 700-2.5 M T 700-2.8 M T 700-3.2 M T 700-3.6 M T 700-4 M T 700-4.8 M T 700-5.5 M T 700-6.4 M TX 700-4.8 M TX 700-5.5 M TX 700-6.4 M TX 700-8 M

A in. 2 2 2 2 2 2 2 2 2 2 3-5/32 3-5/32 3-5/32 3-5/32

B mm 50.8 50.8 50.8 50.8 50.8 50.8 50.8 50.8 50.8 50.8 80 80 80 80

in. 1/16 5/64 3/32 7/64 1/8 9/64 5/32 3/16 7/32 1/4 3/16 7/32 1/4 5/16

E-mail sales@datapowertools.co.uk

mm 1.6 2 2.5 2.8 3.2 3.6 4 4.8 5.5 6.35 4.8 5.5 6.35 8

Premium Quality

SLOTTING CUTTERS & ASSEMBLIES SLOTTING CUTTER ASSEMBLIES B SOLID CARBIDE CUTTER TWELVE TEETH

10 mm

6.35 mm (1/4”) SHANK

PART No.

in. 1-1/4 1-1/4 1-1/4 1-1/4

TA 900 1.2M TA 900 1.6M T 900 1.2M T 900 1.6M

B mm 31.8 31.8 31.8 31.8

in. 3/64 1/16 3/64 1/16

in. 1-5/8 1-5/8

B SOLID CARBIDE CUTTER TWELVE TEETH with ball bearing Guide

9.4mm

6.35 mm (1/4”) SHANK

mm 1.2 1.6 1.2 1.6

ARBOR No. mm 41 TA 11 41 TA 11 Cutter only Cutter only

PART No. TA 900 1.2MB TA 900 1.6MB

in. 1-1/4 1-1/4

mm 31.8 31.8

in. 3/64 1/16

C mm 1.2 1.6

in. 2-3/32 2-3/32

mm 53 53

ARBOR No. TA 10 TA 10

Replacement Ball Bearing TB11

ROUTER BITS

Solid carbide cutters give great rigidity for thin slotting cuts.

SLOTTING CUTTER ASSEMBLIES

BEARINGS & ARBORS BALL BEARINGS

ARBORS

CARE OF BEARINGS: All bearings should be kept free of dust and dirt. They should be cleaned in glue solvent and lightly oiled after each use.

for use with bearings

PART No.

B A

PART No. TB3 TB4 TB5 TB6 TB7 TB8 TB9 TB10 TB11 TB12 TB13 TB14 TB15 TB16 TB17 TB18 TB20

in. 3/4 3/4 1/4 1/2 5/8 3/8 3/8 1/2 0.866 0.945 5/8 13/16 3/4 1.102 1-1/8 -

B mm 28 19 19 6.35 12.7 15.9 9.5 9.5 12.7 22 24 15.9 20.6 19 28 28.6 24

in. 23/64 5/32 7/64 3/16 3/16 1/8 5/32 3/16 .275 5/16 3/16 19/64 9/32 5/16 5/16 -

TA1 TA3 TA4 TA5 TA6 TA7 TA9 TA10 TA13 TA14 TA20 TA21

ID mm 9 4 6 2.7 4.8 4.8 3.2 4 4.8 6.9 8 4.8 7.6 7.1 8 8 5

in. 5/16 1/2 1/8 1/4 3/16 3/16 1/8 3/16 5/16 5/16 1/4 1/4 1/4 0.472 1/2 -

mm 8 12.7 6 3.2 6.35 4.8 4.8 3.2 4.8 8 8 6.35 6.35 6.35 12 12.7 15

B A2 A1

A1 in. 1/4 1/2 1/4 1/2 1/2 1/2 1/4 1/4 1/4 1/2 1/2 1/2

mm 6.35 12.7 6.35 12.7 12.7 12.7 6.35 6.35 6.35 12.7 12.7 12.7

TA8 TA11 TA15 TA16 TA17 TA18

B in. 7/8 7/8 .760 .760 1-1/4 .950 1-1/8 5/8 1-1/2 1-1/2 1-3/4 1-3/4

C mm 22.2 22.2 19.3 19.3 31.8 24.1 28.8 15.9 38.1 38.1 44.4 44.4

in. 2-3/8 2-5/8 2.260 2.510 3.100 3.100 2-3/8 2.062 3 3-1/4 3.600 3-5/8

mm 60 67 57.4 63.7 78.7 78.7 60 52.4 76 82.5 91.4 92

C in. 2.250 1.465 1-7/8 1.780 1.825 1.870

mm 57.1 37.2 47 45.2 46.4 47.5

for use without bearings

PART No.

A2 in. mm 0.315 8 0.315 8 0.315 8 0.315 8 0.315 8 1/2 12.7 1/4 6.35 .295 7.5 0.315 8 0.315 8 0.315 8 1/2 12.7 C

ARBORS

Also a range of shielded bearings available, see page 22.

CARBI-SMOOTH BEARING ASSEMBLIES

A1 in. 1/2 1/4 1/4 1/2 1/4 1/2

mm 12.7 6.35 6.35 12.7 6.35 12.7

A2 in. mm 1/2 12.7 .295 7.5 0.315 8 0.315 8 0.315 8 0.315 8

B in. 3/32 0.030 0.030 0.030 0.120 0.120

mm 2.4 0.8 0.8 0.8 3 3

with Delrin® type sleeves TBT19 has a bevelled smooth surface. All other bearings have a straight surface (as illustrated). BRG ASSEMBLY No. TBT19 (bevelled) TBT20 TBT21 TBT22

BRG. USED TB7 TB7 TB14 TB14

A in. 3/4 5/8 3/4 7/8

A B

mm 19 15.9 19 22.2

in. 15/64 15/64 15/64 15/64

ID mm 6 6 6 6

in. 1/4 1/4 1/4 1/4

mm 6.35 6.35 6.35 6.35

For sales enquires or technical information please call

Tel 0845 2300299 and speak to one of our team ®

www.datapowertools.co.uk

more than powertools

Premium Quality

ALUMINIUM CUTTRES

STRAIGHT BITS FOR WOOD

ROUGHING SPIRAL BITS

For superior edge finish on all types of material. Hardwoods, Softwoods, Laminates, Composites etc. Up cut brings the swarf up and out of the cut. Down cut drives the swarf down and out of the cut.

SOLID CARBIDE - THREE FLUTE

TSRR TSRR TSRR TSRR TSRR TSRR

A UP CUT

DOWN CUT

PART No. TSRW 4 TSRW 5 TSRW 6 TSRW 8 TXSRW 8 TSRW 10 5/16 TSRW 10 1/2 TSRW 8 M TSRW 12 3/8 TSRW 12 1/2 TSRW 10 M TSRW 12 M TSRW 16 1/2 TXSRW 16 1/2 TXXSRW 16 1/2 TSRW 16 M TSRW 20 M

PART No. TSLW 4 TSLW 5 TSLW 6 TSLW 8 TXSLW 8 TSLW 10 5/16 TSLW 10 1/2 TSLW 8 M TSLW 12 3/8 TSLW 12 1/2 TSLW 10 M TSLW 12 M TSLW 16 1/2 TXSLW 16 1/2 TXXSLW 16 1/2 TSLW 16 M TSLW 20 M

in. 1/8 5/32 3/16 1/4 1/4 5/16 5/16

1/2 1/2 1/2

B mm in. 3.18 1/2 3.96 5/8 4.75 3/4 6.35 3/4 6.35 1 7.94 1 7.94 1 8 9.53 1 9.53 1 10 12 12.7 1-1/4 12.7 1-1/2 12.7 2 16 20

3/8 3/8

8 8M 12 3/8 10 M 12 M 16 1/2

in. 1/4

mm 6.35 8 9.53 10 12 12.7

3/8

1/2

in. 3/4

C mm 19.05 25. 25.4 25 32 31.75

1-1/4

in. 2-1/2

mm 63.5 64 63.5 73 74 76.2

2-1/2

available to special order only

C in. mm 2-1/4 57.15 2-1/4 57.15 2-1/4 57.15 2-1/2 63.5 2-1/2 63.5 2-1/2 63.5 3 76.2 64 2-1/2 63.5 3 76.2 73 74 3 76.2 4 101.6 4 101.6 93 100

mm 12.7 16 19 19 25.4 25.4 25.4 25 25.4 25.4 25 32 31.8 38.1 50.8 35 40

PART No.

UP CUT

For increased feed rates to give fast routing of hard materials.

SUFFIX 1/2 = 1/2” SHANK, SUFFIX 5/16”= 5/16” SHANK, SUFFIX 3/8 = 3/8” SHANK, OTHERWISE 1/4” SUFFIX M = SHANK DIAM. SAME AS CUTTING DIAM. SOLID CARBIDE - TWO FLUTE

Also available with Titanium Nitride coating.

COMBINATION TRIMMING DRILLING BITS

COMPRESSION BITS SOLID CARBIDE - TWO FLUTE COMBINATION UP/DOWN CUT SPIRAL

C B

For wood, composites and laminated materials

UP CUT AND DOWN CUT A in. 3/8

PART No. TSRM TSRM TSRM TSRM

12 10 12 16

3/8 M M 1/2

B C mm in. 9.53 1 10 12 12.7 1-1/4

1/2

mm in. 25.4 2-1/2 25 32 31.8 3

mm 63.5 73 74 76.2

FOR NON FERROUS METALS, (ALUMINIUM, LAMINATES, ETC) For aluminium, laminates, etc. Down cut pushes chips below the work. Ideal for trimming laminates and through cutting. Up cuts are ideal for grooving, slotting and routing. SOLID CARBIDE – TWO FLUTE

This bit is used extensively in the caravan repair and manufacturing industries for drilling and trimming sheet aluminium.

UP CUT

DOWN CUT

PART No.

TSR 8 TXSR 8 TSR 12 3/8 TSR 16 1/2

C B

A B C A

B C mm in. mm in. mm 6.35 3/4 19 2-1/2 63.5 6.35 1 25.40 2-1/2 63.5 9.53 1-1/4 31.75 2-1/2 63.5 12.70 1-1/4 31.75 3 76.20

in. 1/4 1/4 3/8 1/2

TSL 8 TXSL 8 TSL 12 3/8 TSL 16 1/2

SOLID CARBIDE – SINGLE “SPOON” FLUTE For aluminium and some soft plastics.

SPIRAL DOWNCUT H I GH SP E E D STE E L - WITH PILOT

SUFFIX 1/2 = 1/2” SHANK, SUFFIX 3/8 = 3/8”SHANK, OTHERWISE 1/4”

C B

A A

PART No HSF 1508 HSF 1512 3/8 HSF 1516 1/2

in. 1/4 3/8 1/2

B mm 6.35 9.5 12.7

in. 3/4 1 1-3/4

C mm 19 25.4 44.4

in. 2-3/4 3 4-1/2

mm 70 76 115

Part No. TSP 04 S TSP 06 S TSP 08 S

SOLID CARBIDE SINGLE FLUTE

For plastics including Bakelite, Acetate, Plexi, PVC, Nylon, etc.

PART No.

TSPR TSPR TSPR TSPR TSPR TSPR

TSPL 02 MS TSPL 03 MS TSPL 04 S TSPL 04 MS TSPL 06 S TSPL 08 S

02 03 04 04 06 08

MS MS S MS S S

in. 5/16 1/2 5/8

C mm 7.94 12.70 16

in. 1-1/2 2-1/4 2-1/4

mm 38.10 57.15 57.15

These bits are used for routing highly abrasive materials such as glass epoxy and fibreglass. Can be used for plunge routing due to the end cutting capability.

DOWN CUT

B mm 3.18 4.75 6.35

FIBREGLASS BITS

FOR PLASTICS

UP CUT

A in. 1/8 3/16 1/4

A A

SOLID CARBIDE - DIAMOND CUT

SUFFIX 1/2 = 1/2” SHANK, C SUFFIX 3/8 = 3/8” SHANK, OTHERWISE 1/4” A in.

1/8 3/16 1/4

B mm 2 3 3.18 4 4.75 6.35

in.

1/2 5/8 5/8

Tel 0845 2300299

mm 8 10 12.7 12 16 16

C in. mm 1-1/2 38.1 1-1/2 38.1 1-1/2 38.1 2-1/4 57.15 2-1/4 57.15 2-1/4 57.15

PART No. TG TG TG TG TG TG

Fax 0870 0117309

8 8 E/C 12 3/8 12 3/8 E/C 16 1/2 16 1/2 E/C

A in. 1/4 1/4 3/8 3/8 1/2 1/2

B mm 6.35 6.35 9.5 9.5 12.7 12.7

in. 3/4 3/4 1 1 1 1

C mm 19 19 25.4 25.4 25.4 25.4

in. 2 2 2-1/2 2-1/2 3 3

E-mail sales@datapowertools.co.uk

mm 50.8 50.8 63.5 63.5 76 76

WOOD BORING DRILS THROUGH BORING DRILLS

HINGE BORING DRILLS

CARBIDE TIPPED

RIGHT HAND A mm 5 8

PART No. WDT5R70 WDT8R70

C mm 70 70

WD25R56 WD30R56 WD35R56

A mm 5 8

PART No. WDT5L70 WDT8L70

WD25R70 WD30R70 WD35R70

A mm 25 30 35

C mm 70 70 70

LEFT HAND

C mm 70 70

10mm diameter shank x 26mm long with adjusting screw.

C PART No. mm 56 WD25L70 56 WD30L70 56 WD35L70

A mm 25 30 35

C mm 70 70 70

HINGE BORING DRILLS For Bench Press and Hand Drill. High quality two flute drill with two scribing teeth produces cleanly cut hole. Not suitable for portable routing machines

RIGHT HAND PART No. WD9.5R56 WD9.5R70 WD10R56 WD10R70 WD11R56 WD11R70 WD12R56 WD12R70

A mm 9.5 9.5 10 10 11 11 12 12

C mm 56 70 56 70 56 70 56 70

CARBIDE TIPPED

RIGHT HAND PART No.

A CARBIDE TIPPED

LEFT HAND A C mm mm 5 56 5 70 6 56 6 70 8 56 8 70 9 56 9 70

WD25L56 WD30L56 WD35L56

A mm 25 30 35

CARBIDE TIPPED

A C mm mm 5 56 5 70 6 56 6 70 8 56 8 70 9 56 9 70

PART No.

10mm diameter shank x 26mm long with adjusting screw.

For multi spindle machines. Suitable for Bench Press and Hand Drill. Not suitable for portable routing machines

WD5L56 WD5L70 WD6L56 WD6L70 WD8L56 WD8L70 WD9L56 WD9L70

PART No.

DOWEL DRILLS

PART No.

A C mm mm 25 56 30 56 35 56

LEFT HAND

WD5R56 WD5R70 WD6R56 WD6R70 WD8R56 WD8R70 WD9R56 WD9R70

RIGHT HAND PART No.

CARBIDE TIPPED

PART No.

CARBIDE TIPPED

PART No. WD9.5L56 WD9.5L70 WD10L56 WD10L70 WD11L56 WD11L70 WD12L56 WD12L70

A mm 9.5 9.5 10 10 11 11 12 12

C mm 56 70 56 70 56 70 56 70

WOOD BORING DRILLS

For multi spindle machines. Suitable for Bench Press and Hand Drill. Not suitable for portable routing machines.

10mm diameter shank x 26mm long (56mm) or 30mm long (70mm) with adjusting screw in end.

TH TH TH TH TH TH TH

20 25 25 30 32 35 35

1/2 3/8 1/2 1/2 1/2 3/8 1/2

C A mm 20 25 25 30 32 35 35

C mm 63.5 57.2 63.5 63.5 63.6 67 67

TOY WHEEL CUTTERS This bit gives the perfect wheel shape for toy making. Available in two sizes, both come with a 6mm interchangeable drill. Recommended for use in Bench or Hand Drills.

6mm DRILL

ADJUSTABLE HINGE BORING BIT

A CARBIDE TIPPED - TWO FLUTES

Adjusts from 20mm-50mm width. Ideal for deep repetitive holes up to 75mm in depth. For bench drill or portable hand drill only. These bits are not suitable for portable router machines.

12.7mm (1/2”) SHANK C

PART No. TWC 40 1/2 TWC 60 1/2

A mm 40 60

B mm 6.3 8

C mm 90 92

CARBIDE TIPPED - TWO FLUTES

10mm (3/8”) SHANK PART No. TAHB 50

A mm 22.5 - 48

B B mm 11

C mm 97

www.datapowertools.co.uk

more than powertools

Premium Quality

ROUTER BITS

REPLACEABLE INSERT ROUTER BITS

Replaceable Insert ROUTER BITS

STRAIGHT BITS

TWO FLUTES

TWO FLUTE

All sizes in millimetres

Part No.

R 1912

6.35

INSERT CODE F

R 1912 1/2

12.7

TWO FLUTE Part No.

• Use End Cutting Inserts for Rebating and Grooving. • Supplied with End Cutting Inserts when New.

R R R R R R R R R R

1830 1830 1840 1930 1930 1940 2030 2030 2040 2040

1/2 16* 1/2 1/2 16* 1/2 1/2 16* 1/2 16*

All sizes in millimetres D

18 18 18 19 19 19 20 20 20 20

30 30 40 30 30 40 30 30 40 40

75 75 80 75 75 84 85 85 85 85

12.7 16.0 12.7 12.7 16 12.7 12.7 12.7 12.7 16

*available to special order only

TWO FLUTE

All sizes in millimetres

Part No.

R 1850 1/2 R 1950 1/2 R 1950 16*

18 19 19

50 50 50

94 94 94

12.7 12.7 16

*available to special order only

Note: 3 Hole Fixing. Note: 3 Hole Inserts used for greater support.

• Use End Cutting Inserts for Rebating and Grooving. • Supplied with End Cutting Inserts when new.

NOTE: Part No’s include cutter bodies complete with Inserts, Screws and Torx Key. Bearing if applicable. End Cutting Inserts designated by Affix E/C, have End Cutting Clearance.

Tel 0845 2300299

INSERT CODE B B C B B C B B C C

Fax 0870 0117309

E-mail sales@datapowertools.co.uk

INSERT CODE E E E

Premium Quality

REPLACEABLE INSERT ROUTER BITS FLUSH TRIMMING BITS

ONE BEARING

TWO FLUTES All sizes in millimetres

Part No.

R 1912 B R 1912 B 1/2

19 19

12 12

57 65

6.35 12.7

INSERT CODE F F

Replacement bearing TB-5

FLUSH TRIMMING BITS

DOUBLE BEARING

TWO FLUTES

TWO FLUTE

All sizes in millimetres

Part No.

R 1912 BB R 1912 BB 1/2

19 19

12 12

61 69

6.35 12.7

INSERT CODE F F

ROUTER BITS

TWO FLUTE

Replacement bearing TB-5

FLUSH TRIMMING BITS

ONE BEARING

TWO FLUTES

TWO FLUTE

All sizes in millimetres

Part No.

R 1930 B 1/2 R 1940 B 1/2

19 19

30 40

82 93

12.7 12.7

INSERT CODE B C

Replacement bearing TB-5

FLUSH TRIMMING BITS

DOUBLE BEARING

TWO FLUTES

TWO FLUTE

All sizes in millimetres

Part No.

R 1930 BB 1/2 R 1940 BB 1/2

19 19

30 40

93 105

12.7 12.7

INSERT CODE B C

Replacement bearing TB-5

FLUSH TRIMMING BITS

ONE BEARING

TWO FLUTES

TWO FLUTE

All sizes in millimetres

Part No.

R 1950 B 1/2

100

12.7

INSERT CODE E

NOTE: 3 Hole Fixing. 3 Hole Inserts used for greater support. Replacement bearing TB-5

INVERTED FLUSH TRIMMING BITS

TWO FLUTES TWO FLUTE

All sizes in millimetres

Part No.

INSERT CODE

REPLACEMENT BEARINGS

RV 1940 B 1/2 RV 1950 B 1/2 RV 2440 B 1/2

19 19 24

40 50 40

84 105 91

2.7 12.7 12.7

C C C

TB-4 TB-4 TB-20

Supplied with End Cutting Inserts when new.

NOTE: Part No’s include cutter bodies complete with Inserts, Screws and Torx Key. Bearing if applicable. End Cutting Inserts designated by Affix E/C, have End Cutting Clearance.

www.datapowertools.co.uk

more than powertools

Premium Quality

ROUTER BITS

REPLACEABLE INSERT ROUTER BITS STRAIGHT BITS

SINGLE FLUTE SINGLE FLUTE Part No.

• Capable of plunge cutting when using End Cutting Inserts. • Supplied with End Cutting Inserts when new.

RS RS RS RS RS RS RS RS RS RS RS RS RS

1230 1/2 12.730 1/2 1430 1/2 1630 1/2 1640 1/2 1640 16* 1830 1/2 1930 1/2 1940 1/2 1940 16* 2030 1/2 2040 1/2 2040 16*

All sizes in millimetres D

12 12.7 14 16 16 16 18 19 19 19 20 20 20

30 30 30 30 40 40 30 30 40 40 30 40 40

75 75 75 85 85 85 85 85 85 85 85 85 85

12.7 12.7 12.7 12.7 12.7 16 12.7 12.7 12.7 16 12.7 12.7 16

INSERT CODE A A A A C C B B C C B C C

*available to special order only

BEVEL TRIMMING BITS

TWO FLUTES TWO FLUTE

All sizes in millimetres

Part No.

R 22 B R 22 B 1/2

19 19

12 12

54 58

6.35 12.7

INSERT CODE F F

Replacement bearing TB-5

BEVEL TRIMMING BITS

TWO FLUTES TWO FLUTE

All sizes in millimetres

Part No.

R 45 B R 45 B 1/2

19 19

12 12

54 58

6.35 12.7

INSERT CODE F F

Replacement bearing TB-5

VEE GROOVE BITS

SINGLE FLUTE All sizes in millimetres

B Part No.

RVG 91 1/2* 18 *available to special order only

12.7

INSERT CODE F

Cuts included angle of 91˚

All sizes in millimetres B Part No. d

15.5

12.7

D RVG 90 1/2* 25 *available to special order only L

Cuts included angle of 90˚

NOTE: Part No’s include cutter bodies complete with Inserts, Screws and Torx Key. Bearing if applicable. End Cutting Inserts designated by Affix E/C, have End Cutting Clearance.

Tel 0845 2300299

Fax 0870 0117309

E-mail sales@datapowertools.co.uk

INSERT CODE G

Premium Quality

REPLACEABLE INSERT ROUTER BITS d

SURFACE PLANERS

3 Flute

4 Flute

CARE SHOULD BE TAKEN WITH SPEED SELECTION.

All sizes in millimetres

Part No.

R3 5512 1/2*

12.7

INSERT CODE F

*available to special order only

Part No.

R4 8012 16M*

INSERT CODE F

ROUTER BITS

FOR USE ONLY IN SECURELY MOUNTED MACHINES.

*available to special order only

INDEXABLE INSERTS *

STANDARD – PL

REPLACEABLE BLADES

INSERTS

Supplied in boxes of 10 only. All Router Bits without bearings are supplied with End Cutting Inserts.

Insert Code from tables A B C D

Carbide grade characteristics

Dimensions, mm

Insert No.

ØD

PL 30 9 1.5 PL 30 12 1.5 PL 40 12 1.5 PL 50 12 1.5

30 30 40 50

9 12 12 12

1.5 1.5 1.5 1.5

4.0 4.0 4.0 4.0

14 14 26 26

GRADE

CHARACTERISTICS

H3M

• • • • • • • •

* DZ05

HM-grade with fine grain size Excellent cutting edge quality Very good abrasion resistance Harder grade HM-grade with extra fine grain size Excellent cutting edge quality Superior abrasion resistance Limited availability

Physical Properties GRADE

Insert Code from tables E

Insert No. PL 50 12 1.7 (3 hole)

Dimensions, mm L

ØD

1.7

4.0

DZ05 H3M

TRANSVERSE RUPTURE STRENGTH

HARDNESS

HV30 1900 1750

HRa 93.8 93.0

N/mm2 2300 1900

psi 333 000 276 000

REPLACEMENT PARTS

Insert Code from tables F

Insert No. PL 12 12 1.5

Dimensions, mm L

ØD

12.0

1.5

4.0

DESCRIPTION Torx Key Torx Head Screw Torx Head Screw Bearing Screw Replacement Bearing Replacement Bearing

Part No. T15 For all bits prefix R & RV M4 For all bits prefix RS M3.5 All Bits M4 For all Bits prefix R TB.5 For all Bits prefix RV TB.4 or TB 20

*Also available in grade DZ05. When ordering replacement blades: State • Insert Number • Carbide Grade • Whether Plain or End Cutting eg. PL 30 12 1.5 H3M E/C

Insert Code from tables G

Insert No. PL 15 12 1.5

Dimensions, mm L

ØD

15.5

1.5

4.0

NOTE • • • • • •

All Straight Bits supplied with End Cutting inserts. All Trimming Bits supplied with standard inserts i.e. not End Cutting. All Router Bits have replaceable Solid Carbide Inserts. Each insert can be rotated to expose a new cutting edge to ensure a constant cutting diameter. Inserts can be removed and replaced without removing cutter from the routing machine. Carbide Grade H 3M is suitable for all applications. A premium Grade DZ05 is often superior but limited to PL 30, 12, 1.5 and PL 12, 12, 1.5 inserts. CAUTION • DO NOT OVERTIGHTEN TORX SCREWS • Ensure Tip Seating is free of burs and resin when changing blades.

www.datapowertools.co.uk

more than powertools