Compaction Concepts Asphalt, HF-rollers and concept comparison
This folder describes the different compaction concepts available on the market. It is an objective comparison on how they function and perform. Several parameters affect the compaction performance of a roller and the most significant are described below. However, only practical testing can truly decide the performance of a roller or show the real difference between machines or concepts.
Compaction Parameters Static linear load The static linear load is calculated by dividing the part of the total roller weight carried by each drum by the width of the drum. Static linear load is normally presented in kg/cm, kN/m or PLI (pounds per linear inch). The static linear load has an influence on the ability of a roller to reach a high degree of compaction. In general, a roller with a higher static linear load will achieve a higher degree of compaction and /or deeper compaction.
Amplitude The nominal amplitude is described as half the travel distance (vertical or horizontal) of the drum. As the counterweight rotates, the drum moves opposite to the counterweight. This means that when the weight is at its highest position, the drum is at its lowest point. The amplitude plays a great part in determining the maximum layer thickness for a roller. A high amplitude (and static linear load) enables the roller to work on a thick layer. Low amplitude limits the depth effect, but also reduces the risk of aggregate crushing.
Frequency The vibration frequency must be selected in relation to the material to be compacted and the amplitude of the roller. Through research and experience it has been found that higher frequencies are outstanding for asphalt compaction compared to lower frequencies. In general, if a lower amplitude is selected, the frequency should be increased to account for the loss in drum acceleration. This is the reason why you may run into inferior compaction results if using an asphalt roller with a too low frequency. High frequency also reduces the risk of rippling.
Miscellaneous The rolling speed has an influence on the compaction performance, it should not exceed 5-6 km/h to assure adequate compaction. Often, lower speeds are required for the first passes on hot asphalt. Several other parameters affect the end-result of an asphalt job.Please refer to “Compaction and Paving, theory and practice� for further details.
Compaction Concepts Static compaction A static compactor works with the static linear load as the only compaction parameter. Compared to a vibratory roller the linear load has to be signifďťżicantly higher to make the static roller an efficient compaction tool. Despite this, it has a limitation of about 50 mm when it comes to layer thickness. Variation in the static linear load is done by ballasting the roller.
Traditional vibration The vibration is generated by one or more eccentric weights rotating on one shaft, centred in the drum. By changing the eccentric mass it is possible to generate different amplitudes. With this type of system the drum will vibrate in a revolving motion generating a “circular amplitude�.
Directional vibration By using two, counter-rotating eccentric weights in the centre of the drum it is possible to create a directional vibration. With a fixed amplitude, the direction of this fixed amplitude is varied from fully vertical to fully horizontal.
Oscillation Two rotating eccentric weights placed away from the drum centre will generate an oscillatory motion of the drum. This means that, as opposed to the two previous, vibrating systems, the drum does not move its axis of rotation, but rather oscillates around it.
Nutation Four counter rotating eccentric weights generate a horizontal movement, transversal to the rolling direction as well as an oscillatory motion.
Disadvantages
Static Compaction
No ground vibration Uncomplicated system Well-known concept Asphalt compaction on bridges
Limited depth effect Number of passes required
Traditional Vibration
Suitable for all materials Most effective method Good depth effect Achieves homogeneous compaction Uncomplicated vibration system
Ground vibration
Directional Vibration
Most effective method (vertical) Good depth effect (vertical) Thin asphalt layer compaction (horiz.) Homogeneous compaction (vertical)
Drum shell wear (horiz.) Ground vibration Complicated vibration systems Only one drum directional
Thin asphalt layer compaction Asphalt compaction on bridges Less transversal ground vibration
Limited depth effect Number of passes required on thick layers Drum shell wear Complicated vibration system Only one drum oscillating
Thin asphalt layer compaction Less ground vibration Asphalt compaction on bridges
Limited depth effect Number of passes required Drum shell wear Complicated vibration system
Nutation
Oscillation
Advantages
Conclusion - traditional and directional Similar in compaction performance when operated manually. However, the automated directional vibration system is questionable on asphalt, due to difficulties in measuring the stiffness accurately at the right depth. Too many alternative settings confuse the operator. A less complicated system will, in general, cause a lesser need, and cost, for maintenance and repair. The directional vibrating roller only has one drum with this type of system. The other has a traditional vibration system, meaning that if one wants to run fully automated, one would have to shut the traditional
vibration off and do twice as many passes as with both drums vibrating.
Static, oscillating & nutation Similar concepts as far as compaction performance is concerned. The most economical way is to achieve compaction with the least complicated equipment, a static roller. They are all suitable for compaction of thin asphalt layers.
Vibratory asphalt compaction requires a lower amplitude and higher frequency than soil compaction. This is a well-known fact, ever since compaction of asphalt with vibratory rollers was first introduced in the 1950’s. Traditionally, the frequency has been around 50 Hz and amplitudes ranging from 0.35 up to 1 mm. However, since the trends in the asphalt industry are moving towards thinner layers and larger aggregates, the compaction equipment needs to develop accordingly. Thinner layers require smaller amplitudes to limit the depth effect and minimize aggregate crushing. To maintain the compaction effect the frequency needs to be increased. This is where the High Frequency asphalt compaction begins.
Asphalt compaction
Low amplitude/High Frequency
Rolling speed
Degree of compaction (%) Marshall
New applications have forced the development of new machines, as a result we have the higher frequencies available. The compaction effect depends on the amplitude and frequency (as well as the static linear load). If the amplitude is reduced, the frequency has toHot asphalt mix, maximum layer thickness 5 cm increase accordingly. This will create a machine with 101 % excellent compaction performance for100.5 thin% layers on Hot asphalt mix, maximum layer thickness 5 cm small amplitude (high frequency), and that works 101 % 100 amplitude % equally well on thicker layers on the high 100.5 % (lower frequency). 99.5 % 99 % 98.5 %
An increased frequency does not mean that the % compaction speed can be increased. Even98though the impact spacing can be maintained at a higher speed 97.5 % with a higher frequency, the compaction result will % suffer. There are also other problems, a 97 high speed1 0 during the initial passes will create a bow wave that can result in cracks and/or bumps in the surface. Consequently, keep the rolling speed in the 3-6 km/h range. An even lower speed may be required for the initial passes.
The use of larger aggregates in thinner layers increase 101 % the risk of aggregate crushing, particularly when using machines with traditional amplitudes and frequencies. 100 % This risk is significantly reduced when a small ampli99 % tude/high frequency machine is used.
Compaction performance
Minimum requirement
Table 1
98 % 97.5 %
2
97 %
3
0
42
1
3
5
6
4
Vibration Frequency: Amplitude: 0.21 mm
7 6
5
78
40 Hz70 Hz
40 Hz
8
No. of passes 70 Hz
Growth of compaction for 40Hz and 70 Hz respectively (equal amplitudes). Note that the 40 Hz curve never reaches the required, minimum degree of compaction.
Hot asphalt mix, maximum layer thickness 5 cm Hot asphalt mix, maximum layer thickness 5 cm 101 %
98 %
97 %
The combination of low amplitude and high frequency is developed for compaction of thin asphalt layers. 96 % For this application it is the most suitable solution, both 2 with regards to compaction performance, and to avoid aggregate crushing.
99 % 98.5 %
Degree of compaction (%) Marshalll
Aggregate crushing
100 % 99.5 %
100 %
99 %
98 %
Table 2
Minimum requirement
97 %
96 %
2
3
3
4
4
5
5
6
Operating speed: Amplitude: 0.23 mm Frequency: 70 Hz
6
7
7 km/h
5 km/h
7
8
8
No. of passes 5 km/h
7 km/h
Compare the number of passes needed to reach the required degree of compaction. If the speed is increased from 5 to 7 km/h, it will take 50 % more passes to reach the required minimum degree of compaction (six passes instead of four).
- Compaction of thin layers requires low amplitude. This, in turn, requires a high frequency to generate sufficient compaction energy. - Low amplitudes minimize the risk of aggregate crushing. - A high frequency does not allow higher rolling speeds, the compaction result may decrease below required levels if the speed exceeds 6 km/h. This means that more passes will have to be done. - A roller with a low amplitude/high frequency setting for thin layers and a high amplitude/lower frequency setting for thick layers is a very versatile machine. It can be used for base and binder courses as well as thin wearing courses.
Degree of compaction (%) Marshall
Conclusions Hot asphalt mix, maximum layer thickness 5 cm
100.5 %
Table 3
100 % 99.5 % 99 % 98.5 % 98 % 97.5 %
35
40
45
50
55
60
65
Frequency (Hz)
Amplitude: 0.21 mm
70
75
The graph shows the relationship between amplitude and frequency and the desired degree of compaction at the 99 % line. The roller was tried with one, fixed amplitude and a variety of different frequencies. It shows that for 80 85 90 a specific amplitude there is a Frequency (Hz) frequency where the compaction is most efficient.
N.B.: All graphs are based on results from full-scale testing of asphalt rollers on hot asphalt mix.
Compaction concepts - comparison Asphalt mix
Practical testing is the only reliable way to show performance differences between the concepts. These tests were carried out under similar circumstances and the compaction temperatures were closely monitored for all concepts to assure an impartial result. The tested concepts were the CC424HF with circular (traditional) vibration with a low amplitude and high frequency, directed vibration (automatic) and oscillation. (N.B.: The oscillating roller has one drum with traditional vibration and one oscillating).
SMA 16-70/100
AG 22 - 160/220
16
22
70-100
160-220
2-5.5
3-8
97.3-100.9
96.9-102.1
90-135
80-125
40
70
41-42
67-74
Max nominal particle size (mm) Penetration (mm*10) Required compaction, air void content (%) Required compaction, degree of compaction (%) Compaction temperature, min/max 째C Layer thickness, desired, mm Layer thickness, mm
Concept No. of passes required
CC424HF Directed Oscillating 6
8
6
Stone mastic 16 - 70/100, 40 mm Degree of compaction (%), Marshall
The CC424HF and the oscillating roller both require six passes to reach the target degree of compaction. The directed vibration roller required eight passes to reach the target air void content.
102 % 101 % 100 % 99 % 98 % 97 % 96 %
0
1
2
3
4
5
6
7
8
9
No. of passes
Directed
CC424HF
Oscillating
Asphalt base 22 - 160/220, 70 mm
Concept No. of passes required
CC424HF Directed Oscillating 6
8
8
102 %
Degree of compaction (%), Marshall
The CC424HF required six passes to reach the target degree of compaction. The automated directed vibration and the oscillating rollers both required eight passes to reach the target air void content.
101 % 100 % 99 % 98 % 97 % 96 % 95 %
0
1
2
3
4
5
6
7
8
9
No. of passes
CC424HF
Directed
Oscillating
Conclusion Thin layer compaction proved to be more efficient with the circular vibration (low amplitude and high frequency) and the oscillating rollers. The automated directed vibration roller required additional passes to reach specifications. However, the lower the amplitude of the machine during compaction, the lesser the risk of aggregate crushing in thin layers of asphalt. This proves to be an advantage for the Dynapac HF machines. The traditional vibration has a rapid growth of compaction on thicker layers
and is able to save two passes compared to the other compaction concepts. This means substantial savings in roller effort and machine input for any given job. It also proves the flexibility and efficiency of the HF concept. To have one, very low, amplitude for efficient compaction of thin layers without crushing and a high amplitude for compaction of thick layers to the correct degree of compaction is a winning concept.
Create lasting results
q
Through our equipment, expertise and support, we contribute to create lasting results that pays off for our customers and other stakeholders.
Focus on Quality
We strive to do things right from the beginning and prioritize right, putting our resources at work where they can create the biggest benefits and return on investment.
q
Take responsibility
We shall be a responsible company in terms of social, environmental, ethical and financial aspects. As a part of the Atlas Copco Group, we share the Group´s objective to do all we can to ensure reliable, lasting results with responsible use of resources; human, natural, and capital.
Dynapac Compaction Equipment AB, Box 504, SE-371 23 Karlskrona, Sweden. Tel: +46 455 30 60 00, Fax: +46 455 30 60 30 We reserve the right to change specifications without notice. Photos and illustrations do not always show standard versions of machines. The above information is a general description only, is not guaranteed and contains no warranties of any kind.
PMI 3294 0031 01 - February 2011
Sustainability is more than just a concept at Dynapac. It is a core value that is reflected in our corporate conduct, our manufacturing processes and the quality control that goes into every piece of Dynapac equipment. Our commitment to lasting results runs throughout the life cycle of our equipment – from product development, sourcing and manufacturing processes, to the use of equipment and service and support offerings. Most importantly, it is a promise to our customers and the communities in which we all live and work to continually develop innovative products and solutions that contribute to a strong infrastructure and a more sustainable environment. At Dynapac, a sustainable future begins today.
q
The Sustainable Way