VIDEO INPUT BOX (VIB) QUICK START GUIDE
Technology, Inc.
A B O U T T H E VIDEO INPUT B O X - The VIB allows you to connect various external devices to be used as video sources (i.e. DVD Player, Video Camera, etc.) - The connection interface of this device is divided as follows: 1 - A / V Connection Panel (located on the front) 2 - System Panel (located at the back)
GETTING POWER FOR THE UNIT
Fans
- Depending on the Model, the VIB
Power Connection
could be internal or external - For Models DS0706 / 0616C / 0808C, the VIB is Internal - The input power is already connected through the display’s main switch; whenever this is turned ON, so will the VIB - For Model DS1508 / 2012, the VIB is External
RS-232 of VIB
TV Tuner
RS-232 of DVI Board*
- Using included power connect to a 110V outlet - See power connector on the right for reference * RS-232 of DVI Board is used for the Monitor System Software (included)
A V A I L A B L E V I DEO INPUTS
SETTING UP EXTERNAL DEVICES d
a - Video-In 1 and 2: composite (RCA) connection b - SVideo-In 1 and 2: standard S-Video connection c - Y.Cb.Cr / Y.Pb.Pr: component video connection d - DVI / VGA: computer or HD-DVI connection
- Steps:
e - TV tuner (on back side of VIB - System Panel)
A V A I L A B L E A UDIO INPUTS
h
a
f - Audio-In 1 and 2: RCA audio connection g - Component Audio-In 1 and 2: RCA audio connection h - PC Audio In: mini jack connection from PC audio or memory card players
f
b
g
c
d
1 - Access the Connection Panel* 2 - Connect the video cable(s) of your External Device** to the Connection Panel eg. memory card player’s S-Video cable, PC’s VGA cable 3 - Connect the audio cable(s) of your External Device to the Connection Panel eg. R / L (red, white) audio cables from memory card player 4 - Ensure proper power connection (if needed) on your External Device
Connection Panel (front of VIB)
e. TV Tuner
power
* Refer to your unit’s manual for location of connection panel ** Examples: DVD, Flash Player, Live Camera Feed, and etc...
External Device (Typical DVD player connection shown as an example)
R E M O T E C O N TROL
GENERAL ACCESS TO THE MENU
Power ON/OFF (save Settings)
Main Menu ON/OFF
Arrow: Up
Sound: Volume Down Arrow: Left
Sound: Volume up Arrow: Right
Enter: to setup or go back Switch two sources
Active Audio Source
- Use the remote for the following steps: 1 - Press MENU button to enter or exit the menu window 2 - Use the arrow buttons to navigate through the menu 3 - Press ENTER button to highlight your selection (selection will turn into RED letters) 4 - Once highlighted, use LEFT / RIGHT arrows to change your selection 5 - Press MENU again to exit
MENU ICONS - From left to right: 1 - IMAGE menu 2 - AUDIO menu 3 - COLOR menu 4 - DISPLAY menu 5 - OSD menu 6 - MISC menu 7 - TV Settings menu
S E L E C T I N G V I DEO INPUT SOURCE
CUSTOMIZING THE DISPLAY
-
ONE input as MAIN-Source : Image will clone, showing TWO of the same screens
Press MENU button to enter window menu Scroll over to the DISPLAY menu Scroll down to either MAIN SOURCE or SUB-SOURCE Press ENTER to highlight the source you want to change (selection will turn into RED letters) - Once highlighted, use LEFT / RIGHT arrows to change your source from Video 1 to Video 2 to SVideo, etc
ONE input as SUB-Source : Image will expand, showing a wide screen in full wrap
C U S T O M I Z I N G THE DISPLAY FULL mode
WPOP mode
POP mode
CON’T
PBP mode
PIP mode Standard picture-inpicture using TV tuner
TWO inputs, MAIN & SUB Sources : TWO different images in separate screens
N OT E :
S E L E C T I N G A UDIO SOURCE - To select Active Audio Source, press the WINDOW button on the VIB remote NOTE:
Audio-In 1 and 2 are shared between SVideo input and Composite Video input PC Audio input is shared between VGA and DVI video inputs
S A VI N G S E T T I NGS - Once your inputs have been set as desired, you can save them as your default inputs by pressing POWER off - You can turn the VIB back on with new default settings
I M A G E A N D AUDIO MENU ADJUSTMENTS - Here you can adjust image brightness and contrast - Also, you can change the volume and change the RGB settings of the display 1 - Press MENU to open the setup menu 2 - Press UP or DOWN to move to your desired selection 3 - Press ENTER button to highlight your selection (selection will turn into RED letters)
4 - Once highlighted, use LEFT / RIGHT arrows to change your selection 5 - Press ENTER to go back to setup menu selections 6 - Press MENU to exit
A P P E N D I X - S HORTCUT KEYS ON THE REMOTE CONTROL
APPENDIX - SHORTCUT KEYS ON THE REMOTE CONTROL
VIDEO INPUT SOURCE - To change the video input source without accessing the menu, use the following shortcut keys
PICTURE MODE - To change the picture mode without accessing the menu, use the following shortcut key
VIDEO button : press repeatedly to circle through Video1 Video2 Svideo1 Svideo2 COMP button : press to switch to and from component Y.Cb.Cr. Y.Pb.Pr. PC button : press to switch to and from VGA DVI
POP or PIP buttons : change from one mode to the other AUDIO INPUT SOURCE - To change the audio input source without accessing the menu, use the following shortcut key WINDOW button : switch active audio source between MAIN source and SUB source * If you DO NOT hear a sound: - ensure proper connection of audio cables - increase the volume using volume knob on the front of VIB - turn volume up with remote
CON’T
D Y N A S C A N C ONTACT INFORMATION Taiwan 66 Hwa-Ya First Road, Hwa-Ya Technical Park, Kuei-Shan Hsiang, Taoyuan Hsien, Taiwan Tel: 886.3.396.0541 Fax: 886.3.396.0545 info@dynascan.com.tw
United States of America: 7 Chrysler, Irvine, California 92618, USA Tel: 949.421.0348 Fax: 949.421.0353 info@dynascanusa.com
Japan 5F, Keihin Tatemono Building, 3-16-10, Shin-Yokohama, Kohoku-Ku, Yokohama, Kanagawa, Japan Tel: 81.45.473.4766 Fax: 81.45.473.0041 sales@dynascan.co.jp
China 3F, Building 40, Number 333, Qin Jiang Road, Shanghai, China Tel: 86.21.6495.9900 Fax: 86.21.6495.3964
DynaScan Technology, Inc. E. info@dynascanusa.com
7 Chrysler, Irvine, CA 92618, USA
www.dynascanusa.com T. 949.421.0348 / F. 949.421.0353