3 Wishes - Spring 2022 Projects

www.3wishesfabric.com

Follow us here to see more exciting projects and ideas!

Tote Featuring the World of Wonder Collection

by Josephine Wall Shipping to stores January 2022

SIDE 1

SIDE 2

Finished Size: 13 1⁄2 in x 17 1⁄2 in (34.29 cm x 44.45 cm)

Fabric Needed 3 Wishes® World of Wonder Collection • 1 yd - Panel (18682-PNL-CTN-D) • 3⁄4 yd - Bubbles (18687 BLU-CTN-D • 1⁄4 yd - Wings (18691-MLT-CTN-D)

Additional Supplies Needed: • 5/8 yd Fusible fleece • Sewing thread • Quilting and sewing supplies • Even-feed foot (optional for quilting)

page 1

Before You Begin Read all instructions before beginning project. Do not pre-wash fabrics. Press fabrics with a dry iron on cotton setting before cutting.

Use a 1⁄2 in (1.27 cm) seam allowance and sew fabrics with right sides together (RST) unless otherwise noted. Press seams in the direction of the arrows. wof = width of fabric Note: A printed panel may become slightly skewed during the finishing process. Check if panel is square before cutting by folding the panel so selvages meet. If all edges do not meet, pull firmly from corner to corner until the edges meet. Continue until all corners are square.

Cutting Use a rotary cutter and acrylic ruler to cut the number of pieces from each fabric listed below.

4 in x wof

14 1⁄2 in x 18 1⁄2 in

Wings (18691-MLT-CTN-D) 1⁄4 yd (9 in x wof / 22.86 cm x 106.68 cm) Cut 1 - 4 in (10.16 cm) x wof for Strap

14 1⁄2 in x 18 1⁄2 in

Fusible Fleece 5⁄8 yd (22.5 in x wof / 57.15 cm x 106.68 cm) Cut 2 - 14 1⁄2 in x 18 1⁄2 in (36.83 cm x 46.99 cm)

World of Wonder Panel (18682-PNL-CTN-D) 1 yd (36 in x 42 in / 91.44 cm x 106.68 cm) Fussy Cut 2 - 14 1⁄2 in x 18 1⁄2 in (36.83 cm x 46.99 cm) for Tote Bag

14 1⁄2 in x 18 1⁄2 in

5 in x 14 1⁄2 in

Bubbles (18687-BLU-CTN-D) 3⁄4 yd (27 in x wof / 68.58 cm x 106.68 cm) Cut 2 - 14 1⁄2 in x 18 1⁄2 in (36.83 cm x 46.99 cm) for Bag Lining Cut 2 - 5 in x 14 1⁄2 in (12.7 cm x 36.83 cm) for Pocket & Pocket Lining

www.3wishesfabric.com

©2022 3 Wishes Fabric®

page 2

Sewing 1. Follow the manufacturer's instructions to fuse the fleece to the wrong side of Bag Side1 and Side 2 rectangles14 1⁄2 in x 18 1⁄2 in (36.83 cm x 46.99 cm).

2. Quilt around the printed images as desired. Pin the Bag Sides RST along the side and bottom edges; sew.

3. To box the bottom, bring the center bottom seam to a side seam RST. Mark 2 in (5.08 cm) from the point and sew from edge to edge. Trim the point to a 1⁄2 in (12.7 mm) seam (Dia. A). Repeat for the other side. Turn Bag right side out.

Dia. A

ng ro W Side

ng ro W Side

Trim to 1⁄2 in (12.7 mm) 2 in (5.08 cm)

4. To make the Strap, fold the Wings strip 4" x 42" (10.16 cm x 106.68 cm) in half lengthwise and press to crease. Refer to Diagram B to open the strip and fold each long edge to the center crease; press. Fold the strip in half again so folded edges meet; press.

Topstitch close to the long edges to make the Wings Strap.

Dia. B Fold to center crease

Fold

Fold Topstitch

5. On the right side of the Bag, pin the ends of the Strap centered over each side seam with cut edges even; sew 1⁄8 in (3.18 mm) from the edge (Dia. C).

Note: Check that Strap is not twisted before sewing.

Dia. C

Pin and sew 1⁄8 in (3.18 mm)

6. Pin the Bubbles Pocket and Pocket Lining 5 in x 14 1⁄2 in (12.7 cm x 36.83 cm) pieces RST and sew along the top and bottom edges. Turn the Pocket right side out through a side opening; press and topstitch close to all edges.

7. On the right side of a Bubbles Lining piece 14 1⁄2 in x 18 1⁄2 in (36.83 cm x 46.99 cm) measure down 5 in (12.7 cm) from the top edge and make a mark at each side edge and also in the center (Dia. D).

www.3wishesfabric.com

©2022 3 Wishes Fabric®

Dia. D

Bubbles Bag Lining 5 in (12.7 cm)

page 3

8. Place the top edge of the Pocket along the 5 in (12.7 cm) marks and pin around the edges; sew close to the side and bottom edges only.

Dia. E

9. Measure 5 1⁄4 in (13.34 cm) from each side edge of the pocket and draw a line from the top to the bottom edge. Sew 1⁄4 in (6.35 mm) along each side of the drawn line to create three pockets (Dia. E).

1⁄4 in (6.35 mm) Align Pocket with Bag Lining marks

5 1⁄4 in (13.34 cm)

5 1⁄4 in (13.34 cm)

10. Pin the Bubbles Lining pieces 14 1⁄2 in x 18 1⁄2 in (36.83 cm x 46.99 cm) RST with edges even. Sew around the side and bottom edges leaving a 5" (12.7 cm) opening in the bottom edge (Dia. F); press seams open. Refer to Step 3 to box the bottom edges. Note: Do not turn Lining right side out.

11. Place the Bag into the Lining RST with side seams and top edges matching; pin along the top edge and sew (Dia. G).

12. Turn the Bag right side out through the opening in the Lining; hand stitch opening closed.

13. Press and topstitch close to the top edge.

Dia. F

Lining

Dia. G

Dia. I

Wrong side

Dia. J

Topstitch

5 in (12.7 cm) Opening

Finished Care Instructions Machine wash in cold water; gentle cycle. Do not bleach. Hang to dry or tumble dry low.

www.3wishesfabric.com

©2022 3 Wishes Fabric®

page 4

www.3wishesfabric.com

Follow us here to see more exciting projects and ideas!

by Josh Rey

Quilt Featuring the Amazement Park collection

by Josh Rey and the Good Vibes collection

by Courtney Morgenstern Shipping to stores January 2022

Finished Size: 46 ½ in x 56 ½ in (118.11 cm x 143.51 cm)

Fabric Needed 3 Wishes Fabric® Amazement Park Collection • 1 Panel – Ferris Wheel Panel (18739-PNL-CTN-D) • 1 1/8 yds – Blueprint (18736-BLK-CTN-D) for Piecing and Binding • 3/4 yd – Ride Patch (18741-BLK-CTN-D) • 1/2 yd – Roller Coaster (18740-BLU-CTN-D) • 1/2 yd – Carousel (18738-BLU-CTN-D) • 1/4 yd – Food Signs (18737-MLT-CTN-D) • 1/4 yd – Popcorn (18742-YLW-CTN-D) • 2 3/4 yds – Food Signs (18737-MLT-CTN-D) for Backing

Additional Supplies Needed: • 55 in x 65 in Cotton batting • Piecing and sewing thread • Quilting and sewing supplies • Even-feed foot (optional for quilting)

3 Wishes Fabric® Good Vibes Collection • 1/3 yd – Circle Dots (18660-WOW-CTN-D)

page 1

Before You Begin Read all instructions before beginning project. Do not pre-wash fabrics. Press fabrics with a dry iron on cotton setting before cutting.

Use a ¼ in (6.35 mm) seam allowance and sew fabrics with right sides together (RST) unless otherwise noted. Press seams in the direction of the arrows. wof = width of fabric.

Note: A printed panel may become slightly skewed during the finishing process. Check if panel is square before cutting by folding the panel so selvages meet. If all edges do not meet, pull firmly from corner to corner until the edges meet. Continue until all corners are square.

Cutting

5 ½ in x 23 ½ in

Use a rotary cutter and ruler to cut the size and number of squares and rectangles from each fabric listed below.

24 ½ in x 34 ½ in

Ride Patch – 18741-BLK-CTN-D (¾ yd x wof / 68.58 cm x 106.68 cm) Cut 4 – 5 ½ in x 23 ½ in (13.97 cm x 59.69 cm) 5 in x 5 in

5 ½ in x 10 ½ in 4 ½ in x 4 ½ in Ferris Wheel Panel – 18739-PNL-CTN-D (1 Panel) Fussy Cut 1 – 24 ½ in x 34 ½ in (62.23 cm x 87.63 cm) 2 ½ in x wof

Roller Coaster – 18740-BLU-CTN-D (5/8 yd x wof / 57.15 cm x 106.68 cm) Cut 2 – 5 ½ in x 10 ½ in (13.97 cm x 26.67 cm) Cut 4 – 5 in x 5 in (12.7 cm x 12.7 cm) Cut 16 – 4 ½ in x 4 ½ in (11.43 cm x 11.43 cm) 1 ½ in x 34 ½ in 5 ½ in x 36 ½ in

1 ½ in x 26 ½ in 5 ½ in x 5 ½ in

5 in x 5 in

4 ½ in x 8 ½ in 4 ½ in x 4 ½ in

Carousel – 18738-BLU-CTN-D (½ yd x wof / 57.15 cm x 106.68 cm) Cut 2 – 5 ½ in x 36 ½ in (13.97 cm x 92.71 cm)

Blueprint – 18736-BLK-CTN-D (1 1/8 yd x wof / 102.87 cm x 106.68 cm) Cut 6 – 2 ½ in x wof (6.35 cm x 106.68 cm) Binding Cut 2 – 1 ½ in x 34 ½ in (3.81 cm x 87.63 cm) Cut 2 – 1 ½ in x 26 ½ in (3.81 cm x 67.31 cm) Cut 4 – 5 ½ in x 5 ½ in (13.97 cm x 13.97 cm) Cut 4 – 5 in x 5 in (12.7 cm x 12.7 cm) Cut 4 – 4 ½ in x 8 ½ in (11.43 cm x 21.59 cm) Cut 8 – 4 ½ in x 4 ½ in (11.43 cm x 11.43 cm)

www.3wishesfabric.com

page 2

1 ½ in x wof 1 ½ in x 23 ½ in

Circle Dots – 18660-WOW-CTN-D (1/3 yd x wof / 30.18 cm x 106.68 cm) Cut 2 – 1 ½ in x wof (3.81 cm x 106.68 cm) Cut 4 – 1 ½ in x 23 ½ in (3.81 cm x 59.69 cm)

4 ½ in x 9 ½ in

Food Signs – 18737-MLT-CTN-D (¼ yd x wof / 22.86 cm x 106.68 cm) Cut 4 – 4 ½ in x 9 ½ in (11.43 cm x 24.13 cm) 4 ½ in x 12 ½ in

4 ½ in x 8 ½ in

Popcorn – 18742-YLW-CTN-D (¼ yd x wof / 22.86 cm x 106.68 cm) Cut 2 – 4 ½ in x 12 ½ in (11.43 cm x 31.75 cm) Cut 2 – 4 ½ in x 8 ½ in (11.43 cm x 21.59 cm)

Sewing 1.

Draw a diagonal line on the wrong side of a Roller Coaster square (5 in x 5 in / 12.7 cm x 12.7 cm) as shown in Diagram A. Place on top of a Blueprint square (5 in x 5 in / 12.7 cm x 12.7 cm) RST and sew ¼ in (6.35 mm) away from the line on both sides. Cut on the drawn line; press; trim if necessary. Note: Two squares yield two Half-Square Triangle Units. Repeat to make a total of eight Half-Square Triangle Units (4 ½ in x 4 ½ in / 11.43 cm x 11.43 cm).

Dia. A

Half-Square Triangle Unit

Draw wrong side

Sew

Cut

Press

Square up to 4 ½ in to 4 ½ in (11.43 cm x 11.43 cm) Make 8

2.

Refer to Diagram B to make Flying Geese Units. Draw a diagonal line on the wrong side of a Roller Coaster square (4 ½ in x 4 ½ in / 11.43 cm x 11.43 cm). Place RST on the left side of a Blueprint rectangle (4 ½ in x 8 ½ in / 11.43 cm x 21.59 cm). Sew on the diagonal line. Trim seam to ¼ in (6.35 mm); press open. Repeat with a second Roller Coaster square (4 ½ in x 4 ½ in / 11.43 cm x 11.43 cm) on the right side of the rectangle to make a Roller Coaster/Blueprint Flying Geese Unit (4 ½ in x 8 ½ in / 11.43 cm x 21.59 cm). Make four.

Dia. B

Roller Coaster/Blueprint Flying Geese Unit

Draw wrong side

www.3wishesfabric.com

Sew

Cut

Press

4 ½ in to 8 ½ in (11.43 cm x 21.59 cm) Make 4

page 3

3.

Follow Step 2 and refer to Diagram C using four Blueprint squares (4 ½ in x 4 ½ in / 11.43 cm x 11.43 cm) and two Popcorn rectangles (4 ½ in x 8 ½ in / 11.43 cm x 21.59 cm) to make two Blueprint/Popcorn Flying Geese Units (4 ½ in x 8 ½ in / 11.43 cm x 21.59 cm).

Dia. C Blueprint/Popcorn Flying Geese Unit

4 ½ in to 8 ½ in (11.43 cm x 21.59 cm) Make 2

4.

Follow Step 2 and refer to Diagram D using Blueprint squares (5 ½ in x 5 ½ in / 13.97 cm x 13.97 cm) and two Roller Coaster rectangles (5 ½ in x 10 ½ in / 13.97 cm x 26.67 cm) to make two Blueprint/Roller Coaster Flying Geese Units (5 ½ in x 10 ½ in / 13.97 cm x 26.67 cm).

Dia. D Blueprint/Roller Coaster Flying Geese Unit

5 ½ in to 10 ½ in (13.97 cm x 26.67 cm) Make 2

5.

Follow the method for corner triangles in Step 2 and refer to Diagram E using four Roller Coaster squares (4 ½ in x 4 ½ in / 11.43 cm x 11.43 cm) and two Popcorn rectangles (4 ½ in x 12 ½ in / 11.43 cm x 31.75 cm) to make two Roller Coaster/Popcorn Side Border Units (4 ½ in x 12 ½ in / 11.43 cm x 31.75 cm).

Dia. E Blueprint/Popcorn Flying Geese Unit

4 ½ in to 12 ½ in (11.43 cm x 31.75 cm) Make 2

6.

Follow the method for corner triangles in Step 2 and refer to Diagram F using four Roller Coaster squares (4 ½ in x 4 ½ in / 11.43 cm x 11.43 cm), four Blueprint squares (4 ½ in x 4 ½ in / 11.43 cm x 11.43 cm) and four Food Signs rectangles (4 ½ in x 9 ½ in / 11.43 cm x 24.13 cm) to make the four Roller Coaster/Blueprint/Food Signs Units 1-4 (4 ½ in x 9 ½ in / 11.43 cm x 24.13 cm). Note: Check orientation of Food Sign design.

Dia. F

7.

Roller Coaster/ Blueprint/ Food Signs Unit 1

Roller Coaster/ Blueprint/ Food Signs Unit 2

Roller Coaster/ Blueprint/ Food Signs Unit 3

Roller Coaster/ Blueprint/ Food Signs Unit 4

4 ½ in to 9 ½ in (24.13 cm x 31.75 cm) Make 1

4 ½ in to 9 ½ in (24.13 cm x 31.75 cm) Make 1

4 ½ in to 9 ½ in (24.13 cm x 31.75 cm) Make 1

4 ½ in to 9 ½ in (24.13 cm x 31.75 cm) Make 1

Place two HST Units (4 ½ in x 4 ½ in / 11.43 cm x 11.43 cm), two Roller Coaster/Blueprint FG Units (4 ½ in x 8 ½ in / 11.43 cm x 21.59 cm) and one Roller Coaster/Popcorn Side Border Unit (4 ½ in x 12 ½ in / 11.43 cm x 31.75 cm) as shown in Diagram G. Pin RST, sew and press to make the Inner Side Border (4 ½ in x 36 ½ in / 11.43 cm x 92.71 cm). Repeat to make two.

Dia. G +

+

+

+

=

Inner Side Border

4 ½ in to 36 ½ in (11.43 cm x 92.71 cm) Make 2

www.3wishesfabric.com

page 4

8.

Follow Step 7 and refer to Diagram H using two HST Units (4 ½ in x 4 ½ in / 11.43 cm x 11.43 cm), Roller Coaster/Blueprint/Food Signs Units 1 and 2 (4 ½ in x 9 ½ in / 11.43 cm x 24.13 cm) and one Blueprint/Popcorn FG Unit (4 ½ in x 8 ½ in / 11.43 cm x 21.59 cm) to make the Inner Top Border (4 ½ in x 34 ½ in / 11.43 cm x 87.63 cm). Note: Check orientation of Food Sign design.

Dia. H

Inner Top Border

4 ½ in to 34 ½ in (11.43 cm x 87.63 cm)

9.

Follow Step 7 and refer to Diagram I using two HST Units (4 ½ in x 4 ½ in / 11.43 cm x 11.43 cm), Roller Coaster/Blueprint/Food Signs Units 3 and 4 (4 ½ in x 9 ½ in / 11.43 cm x 24.13 cm) and one Blueprint/Popcorn FG Unit (4 ½ in x 8 ½ in / 11.43 cm x 21.59 cm) to make the Inner Bottom Border (4 ½ in x 34 ½ in / 11.43 cm x 87.63 cm). Note: Check orientation of Food Sign design.

Dia. I

Inner Bottom Border

4 ½ in to 34 ½ in (11.43 cm x 87.63 cm)

10. Place two Circle Dots strips (1 ½ in x 23 ½ in / 3.81 cm x 59.69 cm) as shown in Diagram J. Pin RST, sew and press open or to one side to make the Circle Dots Side Border (1 ½ in x 46 ½ in / 3.81 cm x 118.11 cm). Repeat to make two.

Dia. J + Circle Dots Side Borders 1 ½ in to 46 ½ in (3.81 cm x 118.11 cm) Make 2

11. Place one Ride Patch rectangle (5 ½ in x 23 ½ in / 13.97 cm x 59.69 cm) on each side of one Blueprint/Roller Coaster FG Unit (5 ½ in x 10 ½ in / 13.97 cm x 26.67 cm) as shown in Diagram K. Pin RST, sew and press to make the Outer Left Side Border (5 ½ in x 56 ½ in / 13.97 cm x 59.69 cm). Note: Check orientation of Ride Patch design.

Dia. K

+

+

=

Outer Left Side Border

5 ½ in to 56 ½ in (13.97 cm x 143.51 cm)

12. Follow Step 11 and Diagram L to make the Outer Right Side Border (5 ½ in x 56 ½ in / 13.97 cm x 59.69 cm). Note: Check orientation of Ride Patch design.

Dia. L

Outer Right Side Border

5 ½ in to 56 ½ in (13.97 cm x 143.51 cm)

www.3wishesfabric.com

page 5

13. Refer to Diagram M to place the Borders as shown around the Fussy Cut Ferris Wheel Panel rectangle (24 ½ in x 34 ½ in / 62.23 cm x 87.63 cm). Sew each Border RST in the order listed. Pin matching center, seams and ends. Press seams as shown. Measure at each step to ensure the next border will fit. Note: Check orientation of fabric design. Tip: If one border is a little larger than the border it is being sewn to, pin well to ease the fullness and place the fullness on the bottom while sewing. Finished Quilt Top should measure 46 ½ in x 56 ½ in (118.11 cm x 143.51 cm).

Blueprint Border Sides: 2 – Blueprint strips (1 ½ in x 34 ½ in / 3.81 cm x 87.63 cm) Top and Bottom: 2 – Blueprint strips (1 ½ in x 26 ½ in / 3.81 cm x 67.31 cm) Quilt Top - 26 ½ in x 36 ½ in (67.31 cm x 92.71 cm).

Inner Border Sides: 2 – Inner Side Borders; made in Step 7 (4 ½ in x 36 ½ in / 11.43 cm x 92.71 cm) Top and Bottom: 2 – Top and Bottom Borders; made in Steps 8 and 9 (4 ½ in x 34 ½ in / 11.43 cm x 87.63 cm) Quilt Top - 34 ½ in x 44 ½ in (87.63 cm x 113.03 cm).

Circle Dots Border Top and Bottom: 2 – Circle Dots strips (1 ½ in x 34 ½ in / 3.81 cm x 87.63 cm) Sides: 2 – Circle Dots Side Borders made in Step 10 (1 ½ in x 46 ½ in / 3.81 cm x 118.11 cm) Quilt Top – 36 ½ in x 46 ½ in (92.71 cm x 118.11 cm).

Outer Border Top and Bottom: 2 – Carousel rectangles (5 ½ in x 36 ½ in) Sides: 2 – Side Borders; made in Steps 11 and 12 (5 ½ in x 56 ½ in / 13.97 cm x 143.51 cm) Quilt Top – 46 ½ in x 56 ½ in (118.11 cm x 143.51 cm).

Dia. M + +

+ +

+

+

+

+

+

+

+

+

+ +

+ +

46 ½ in to 56 ½ in (118.11 cm x 143.51 cm)

www.3wishesfabric.com

page 6

Finishing

Dia. N

14. Remove the selvages from the Food Signs Backing fabric.

Note: Check orientation of design. Cut one piece 40 ¼ in x 65 in (102.235 cm x 165.1 cm) and two pieces 15 ¼ in x 32 ¾ in (38.735 cm x 83.185 cm). Pin RST, sew the two smaller pieces on the short edges; press. Pin the two sections RST along the long edges and sew as shown in Diagram N. Press the seam open or to one side.

The Backing should measure 55 in x 65 in (139.7 cm x 165.1 cm).

15. Press finished Quilt Top and Backing. Tape the Backing, wrong side up, to a firm surface. Layer Batting and Quilt Top (right side up).

Baste the layers together with safety pins. Quilt as desired.

16. Once quilting is complete, square up corners and edges, trimming excess Backing and Batting even with the Quilt Top.

Backing 55 in to 65 in (139.71 cm x 165.1 cm)

17. Binding – Follow Diagram O to make the Blueprint Binding. Remove selvages and sew the short ends of the six 2 ½ in x wof strips (6.35 cm x wof) RST end to end at a 45˚ angle to make one continuous strip; press seams open. Press one short end ¼ in (6.35 mm) to the wrong side. Fold in half lengthwise with wrong sides together; press. Leaving a 2 in (5.08 cm) tail on the folded end, place cut edges of folded Binding even with the edge of the Quilt Top and sew, mitering the corners. Overlap ends, trim any excess and finish.

Dia. O

Stop stitching ¼ in (6.35 mm) from end of quilt

Finished Care Instructions Machine wash in cold water; gentle cycle. Do not bleach. Tip: Before drying, check for fabric dyes that may have run. If fabric dyes run, rewash and rinse using a color catcher to absorb loose dye. Lay flat to dry or tumble dry low.

www.3wishesfabric.com

page 7

www.3wishesfabric.com

Follow us here to see more exciting projects and ideas!

Quilt Featuring the Forest Friends Collection

by Audrey Jeanne Roberts and the Good Vibes Collection

by Courtney Morgenstern Shipping to stores January 2022

Finished Size: 48 ½ in x 48 ½ in (123.19 cm x 123.19 cm)

Fabric Needed 3 Wishes Fabric® Forest Friends Collection • 1 1/4 yds – Plaid Patch (18681-MLT-CTN-D) • 7/8 yd – Plaid (18678-NVY-CTN-D) for Piecing and Binding • 3/4 yd – Scenic (18677-WHT-CTN-D) • 3/8 yd – Fox (18680-GRN-CTN-D) • 1/4 yd – Trees (18679-GRN-CTN-D) • 2 1/2 yds – Fox (18680-GRN-CTN-D) Backing-Directional

Additional Supplies Needed: • 56 in x 56 in (142.24 cm x 142.24 cm) Cotton batting • 17 in x 27 in (43.18 cm x 68.58 cm) Lightweight fusible web • Piecing and sewing thread • Quilting and sewing supplies • Even-feed foot (optional for quilting)

3 Wishes Fabric® Good Vibes Collection • 1 1/8 yds – Circle Dots (18660-WOW-CTN-D)

page 1

Before You Begin Read all instructions before beginning project. Do not pre-wash fabrics. Press fabrics with a dry iron on cotton setting before cutting.

Use a ¼ in (6.35 mm) seam allowance and sew fabrics with right sides together (RST) unless otherwise noted. Press seams in the direction of the arrows. wof = width of fabric. Print Appliqué Templates at 100% scale.

Cutting Use a rotary cutter and ruler to cut the size and number of squares and rectangles from each fabric listed below. Set aside the remaining fabric for making the appliqués.

2 in x 37 ½ in 4 ½ in x 40 ½ in

2 in x 34 ½ in

26 ½ in x 26 ½ in

Circle Dots – 18660-WOW-CTN-D (1 1⁄8 yds x wof / 102.87 cm x 106.68 cm) from the 3W Good Vibes Collection Cut 2 – 2 in x 37 ½ in (5.08 cm x 95.25 cm) Cut 2 – 2 in x 34 ½ in (5.08 cm x 87.63 cm) Cut 1 – 26 ½ in x 26 ½ in (67.31 cm x 67.31 cm)

Plaid Patch – 18681-MLT-CTN-D (1 ¼ yds x wof / 114.3 cm x 106.68 cm) Fussy Cut 4 – 4 ½ in x 40 ½ in (11.43 cm x 102.87 cm)

2 ½ in x wof

2 in x 40 ½ in 2 in x 37 ½ in

Lg. Triangle Appliqué

www.3wishesfabric.com

Triangle Base Appliqué

Sm. Triangle Appliqué

Plaid – 18678-NVY-CTN-D (7⁄8 yd x wof / 80.1 cm x 106.68 cm) Cut 5 – 2 ½ in x wof (6.35 cm x 106.68 cm) for Binding Cut 2 – 2 in x 40 ½ in (5.08 cm x 102.87 cm) Cut 2 – 2 in x 37 ½ in (5.08 cm x 95.25 cm) Cut 1 – Lg. Triangle Appliqué Cut 1 – Triangle Base Appliqué Cut 1 – Sm. Triangle Appliqué

page 2

4 ½ in x 4 ½ in

4 ½ in x 26 ½ in

Lg. Triangle Appliqué

Lg. Triangle Appliqué

Triangle Base Appliqué

Sm. Triangle Appliqué

Fox – 18680-GRN-CTN-D (3⁄8 yd x wof / 34.29 cm x 106.68 cm) Cut 8 – 4 ½ in x 4 ½ in (11.43 cm x 11.43 cm) Cut 1 – Lg. Triangle Appliqué Cut 1 – Triangle Base Appliqué Cut 1 – Sm. Triangle Appliqué

Sm. Triangle Appliqué

Lg. Triangle Appliqué

Scenic – 18677-WHT-CTN-D (¾ yd x wof / 68.58 cm x 106.68 cm) Cut 4 – 4 ½ in x 26 ½ in (11.43 cm x 67.31 cm) Cut 1 – Lg. Triangle Appliqué Cut 1 – Sm. Triangle Appliqué

Triangle Base Appliqué

Sm. Triangle Appliqué

8 in Circle Template

Trees – 18679-GRN-CTN-D (¼ yd x wof / 22.86 cm x 106.68 cm) Cut 1 – Lg. Triangle Appliqué Cut 1 – Triangle Base Appliqué Cut 1 – Sm. Triangle Appliqué Cut 1 – 8 in (20.32 cm) Circle Appliqué

Sewing 1.

Use the templates provided to trace the number of appliqué shapes on the paper side of fusible web as shown in Diagram A. Leave ¼ in (6.35 mm) between shapes and cut out 1/8 in (3.18 mm) outside the traced line.

Dia. A 8 in Circle Template Lg. Triangle Appliqués

Triangle Base Appliqués Sm. Triangle Appliqués Lightweight fusible web (17 in x 27 in / 43.18 cm x 68.58 cm) Cut 1 – 8 in (20.32 cm) Circle Appliqué Cut 3 – Triangle Base Appliqué Cut 4 – Lg. Triangle Appliqué Cut 4 – Sm. Triangle Appliqué

www.3wishesfabric.com

page 3

2.

Refer to Diagram B to place the fusible web appliqué pieces on the wrong side of each fabric, adhesive side down. Fuse according to the manufacturer’s directions. Cut out on the traced lines. Remove paper backing.

Dia. B wrong side

wrong side Lg. Triangle Appliqué

Lg. Triangle Appliqué

Sm. Triangle Appliqué

Triangle Base Appliqué

Triangle Base Appliqué

Sm. Triangle Appliqué

Fox – 18680-GRN-CTN-D Cut 1 – Lg. Triangle Appliqué Cut 1 – Triangle Base Appliqué Cut 1 – Sm. Triangle Appliqué

Plaid – 18678-NVY-CTN-D Cut 1 – Lg. Triangle Appliqué Cut 1 – Triangle Base Appliqué Cut 1 – Sm. Triangle Appliqué wrong side Lg. Triangle Appliqué

Sm. Triangle Appliqué

Triangle Base Appliqué

8 in Circle Template

wrong side

Trees – 18679-GRN-CTN-D Cut 1 – Lg. Triangle Appliqué Cut 1 – Triangle Base Appliqué Cut 1 – Sm. Triangle Appliqué Cut 1 – 8 in (20.32 cm) Circle Appliqué

Lg. Triangle Appliqué Sm. Triangle Appliqué

Scenic – 18677-WHT-CTN-D Cut 1 – Lg. Triangle Appliqué Cut 1 – Sm. Triangle Appliqué

3.

Refer to Diagram C to position the appliqué pieces right side up on the right side of the Circle Dots square (26 ½ in x 26 ½ in / 67.31 cm x 67.31 cm). Center the triangle tree shapes on top of each other as shown. Note: Check that appliqué pieces are at least 3/4 in (19.1 mm) away from edges and check orientation of designs. Fuse to the right side of the fabric according to the manufacturer’s directions. Use a coordinating thread and small buttonhole or zig-zag stitch to secure and finish the edges. The Center Appliqué Block should measure 26 ½ in x 26 ½ in (67.31 cm x 67.31 cm).

Center Appliqué Block

Dia. C

1 ¾ in (4.45 cm)

3 ½ in (8.89 cm) 4 ¾ in (12.07 cm)

Buttonhole stitch

3 ¼ in (8.26 cm) ¾ in (1.91 cm) 8 ¾ in (22.23 cm) 6 in (15.24 cm)

4 ¾ in (12.07 cm)

Zigzag stitch 4 ¾ in (12.07 cm)

3 ¼ in (8.26 cm) 4 ¼ in (10.8 cm)

3 ¼ in (8.26 cm) ¾ in (1.91 cm)

4 ¾ in (12.07 cm)

26 ½ in x 26 ½ in (67.31 cm x 67.31 cm)

1 ¼ in (3.18 cm)

6 3⁄8 in (16.19 cm)

www.3wishesfabric.com

page 4

4.

Place a Fox square (4 ½ in x 4 ½ in / 11.43 cm x 11.43 cm) on each side of a Scenic rectangle (4 ½ in x 26 ½ in / 11.43 cm x 67.31 cm) as shown in Diagram D. Pin RST, sew and press to make the Scenic Top Border (4 ½ in x 34 ½ in / 11.43 cm x 87.63 cm). Repeat to make the Scenic Bottom Border. Note: Check orientation of designs.

Dia. D +

+ = Scenic Top and Bottom Border

4 ½ in x 34 ½ in (11.43 cm x 87.63 cm) Make 2

5.

Place a Fox square (4 ½ in x 4 ½ in / 11.43 cm x 11.43 cm) on each side of a Plaid Patch Fussy Cut rectangle (4 ½ in x 40 ½ in / 11.43 cm x 102.87 cm) as shown in Diagram E. Pin RST, sew and press to make the Plaid Patch Top Border (4 ½ in x 48 ½ in / 11.43 cm x 123.19 cm). Note: Check orientation of designs.

Dia. E +

+ = Plaid Patch Top Border

4 ½ in x 48 ½ in (11.43 cm x 123.19 cm)

6.

Place a Fox square (4 ½ in x 4 ½ in / 11.43 cm x 11.43 cm) on each side of a Plaid Patch Fussy Cut rectangle (4 ½ in x 40 ½ in / 11.43 cm x 102.87 cm) as shown in Diagram F. Pin RST, sew and press to make the Plaid Patch Bottom Border (4 ½ in x 48 ½ in / 11.43 cm x 123.19 cm ). Note: Check orientation of designs.

Dia. F +

+ = Plaid Patch Bottom Border

4 ½ in x 48 ½ in (11.43 cm x 123.19 cm)

www.3wishesfabric.com

page 5

7.

Refer to Diagram G to place the Borders around the Center Appliqué Block (26 ½ in x 26 ½ in / 67.31 cm x 67.31 cm). Sew each Border RST in the order listed. Pin matching center, seams and ends. Press seams as shown. Measure at each step to ensure the next border will fit. If one border is a little larger than the border it is being sewn to, pin well to ease the fullness and place the fullness on the bottom while sewing. Finished Quilt Top should measure 48 ½ in x 48 ½ in (123.19 cm x 123.19 cm).

Scenic Border Sides: 2 – Scenic rectangles (4 ½ in x 26 ½ in / 11.43 cm x 67.31 cm) Top and Bottom: Scenic Top and Bottom Borders (4 ½ in x 34 ½ in / 11.43 cm x 87.63 cm) Quilt Top - 34 ½ in x 34 ½ in (87.63 cm x 87.63 cm) Circle Dots Border Top and Bottom: 2 – Circle Dots strips (2 in x 34 ½ in / 5.08 cm x 87.63 cm) Sides: 2 – Circle Dots strips (2 in x 37 ½ in / 5.08 cm x 95.25 cm) Quilt Top - 37 ½ in x 37 ½ in (95.25 cm x 95.25 cm) Plaid Border Top and Bottom: 2 – Plaid strips (2 in x 37 ½ in / 5.08 cm x 95.25 cm) Sides: 2 – Plaid strips (2 in x 40 ½ in / 5.08 cm x 102.87 cm) Quilt Top - 40 ½ in x 40 ½ in (102.87 cm x 102.87 cm) Plaid Patch Border Sides: 2 – Plaid Patch Fussy Cut rectangles (4 ½ in x 40 ½ in / 11.43 cm x 102.87 cm) Top and Bottom: Plaid Patch Top and Bottom Borders (4 ½ in x 48 ½ in / 11.43 cm x 123.19 cm).

Dia. G

+ + +

+

+

+

+

+

+

+

+

+

+

+ + +

48 ½ in x 48 ½ in (123.19 cm x 123.19 cm)

www.3wishesfabric.com

page 6

Finishing 8.

9.

Dia. H

Remove the selvages from the Fox Backing fabric.

Note: Check orientation of designs. Cut one piece 40 ¼ in x 56 in (102.24 cm x 142.24 cm) and two pieces 16 ¼ in x 28 ¼ in (41.28 cm x 71.76 cm). Pin RST and sew the two smaller pieces on the short edges; press. Pin the two sections RST and sew along the long edges as shown in Diagram H. Press the seam open or to one side. The Backing should measure 56 in x 56 in (142.24 cm x 142.24 cm).

Press finished Quilt Top and Backing. Tape the Backing, wrong side up, to a firm surface. Layer Batting and Quilt Top (right side up). Baste the layers together with safety pins. Quilt as desired.

10. Once quilting is complete, square up corners and edges, trimming excess Backing and Batting even with the Quilt Top.

16 ¼ in x 28 ¼ in (41.28 cm x 71.76 cm)

40 ¼ in x 56 in (102.24 cm x 142.24 cm)

16 ¼ in x 28 ¼ in (41.28 cm x 71.76 cm)

Backing 56 in x 56 in (142.24 cm x 142.24 cm)

11. Binding – Follow Diagram I to make the Plaid Binding. Remove selvages and sew the short ends of the five 2 ½ in (6.35 cm) x wof strips RST end to end at a 45° angle to make one continuous strip; press seams open. Press one short end ¼ in (6.35 mm) to the wrong side. Fold in half lengthwise with wrong sides together; press. Leaving a 2 in (5.08 cm) tail on the folded end, place cut edges of folded Binding even with the edge of the Quilt Top and sew, mitering the corners. Overlap ends, trim any excess and finish sewing the Binding. Fold Binding over to back and hand stitch.

Dia. I

Stop stitching ¼ in (6.35 mm) from end of quilt

Finished Care Instructions Machine wash in cold water; gentle cycle. Do not bleach. Tip: Before drying, check for fabric dyes that may have run. If fabric dyes run, rewash and rinse using a color catcher to absorb loose dye. Lay flat to dry or tumble dry low.

www.3wishesfabric.com

©2022 3 Wishes Fabric®

page 7

Appliqué Template (100% Scale) Trace on paper side of fusible web.

Scale: 1 square = 1 in x 1 in

8 in Circle Template Cut 1 – Trees

Appliqué Template (100% Scale) Trace on paper side of fusible web.

Scale: 1 square = 1 in x 1 in

Triangle Base Template Cut 1 – Trees Cut 1 – Plaid Cut 1 – Fox

Appliqué Template (100% Scale) Trace on paper side of fusible web.

Scale: 1 square = 1 in x 1 in

Lg. Triangle Template Cut 1 – Trees Cut 1 – Plaid Cut 1 – Fox Cut 1 – Scenic

Sm. Triangle Template Cut 1 – Trees Cut 1 – Plaid Cut 1 – Fox Cut 1 – Scenic

www.3wishesfabric.com

Follow us here to see more exciting projects and ideas!

Quilt Featuring the Forest Friends Collection

by Audrey Jeanne Roberts and the Good Vibes Collection

by Courtney Morgenstern Shipping to stores January 2022

Finished Size: 48 ½ in x 48 ½ in (123.19 cm x 123.19 cm)

Fabric Needed 3 Wishes Fabric® Forest Friends Collection • 1 1/4 yds – Arrow Patch (18672-MLT-CTN-D) • 7/8 yd – Tents (18675-BLU-CTN-D) for Piecing and Binding • 3/4 yd – Floral (18674-WHT-CTN-D) • 3/8 yd – Tossed Animals (18673-PNK-CTN-D) • 1/4 yd – Deer (18679-YLW-CTN-D) • 2 1/2 yds – Tossed Animals (18673-PNK-CTN-D) Backing-Directional

Additional Supplies Needed: • 56 in x 56 in (142.24 cm x 142.24 cm) Cotton batting • 17 in x 27 in (43.18 cm x 68.58 cm) Lightweight fusible web • Piecing and sewing thread • Quilting and sewing supplies • Even-feed foot (optional for quilting)

3 Wishes Fabric® Good Vibes Collection • 1 1/8 yds – Circle Dots (18660-WOW-CTN-D)

page 1

Before You Begin Read all instructions before beginning project. Do not pre-wash fabrics. Press fabrics with a dry iron on cotton setting before cutting.

Use a ¼ in (6.35 mm) seam allowance and sew fabrics with right sides together (RST) unless otherwise noted. Press seams in the direction of the arrows. wof = width of fabric. Print Appliqué Templates at 100% scale.

Cutting Use a rotary cutter and ruler to cut the size and number of squares and rectangles from each fabric listed below. Set aside the remaining fabric for making the appliqués.

2 in x 37 ½ in 4 ½ in x 40 ½ in

2 in x 34 ½ in

26 ½ in x 26 ½ in

Circle Dots – 18660-WOW-CTN-D (1 1⁄8 yds x wof / 102.87 cm x 106.68 cm) from the 3W Good Vibes Collection Cut 2 – 2 in x 37 ½ in (5.08 cm x 95.25 cm) Cut 2 – 2 in x 34 ½ in (5.08 cm x 87.63 cm) Cut 1 – 26 ½ in x 26 ½ in (67.31 cm x 67.31 cm)

Arrow Patch – 186721-MLT-CTN-D (1 ¼ yds x wof / 114.3 cm x 106.68 cm) Fussy Cut 4 – 4 ½ in x 40 ½ in (11.43 cm x 102.87 cm)

2 ½ in x wof

2 in x 40 ½ in 2 in x 37 ½ in

Lg. Triangle Appliqué

www.3wishesfabric.com

Triangle Base Appliqué

Sm. Triangle Appliqué

Tents – 18675-BLU-CTN-D (7⁄8 yd x wof / 80.1 cm x 106.68 cm) Cut 5 – 2 ½ in x wof (6.35 cm x 106.68 cm) for Binding Cut 2 – 2 in x 40 ½ in (5.08 cm x 102.87 cm) Cut 2 – 2 in x 37 ½ in (5.08 cm x 95.25 cm) Cut 1 – Lg. Triangle Appliqué Cut 1 – Triangle Base Appliqué Cut 1 – Sm. Triangle Appliqué

page 2

4 ½ in x 4 ½ in

4 ½ in x 26 ½ in

Lg. Triangle Appliqué

Lg. Triangle Appliqué

Triangle Base Appliqué

Sm. Triangle Appliqué

Tossed Animals – 18673-PNK-CTN-D (3⁄8 yd x wof / 34.29 cm x 106.68 cm) Cut 8 – 4 ½ in x 4 ½ in (11.43 cm x 11.43 cm) Cut 1 – Lg. Triangle Appliqué Cut 1 – Triangle Base Appliqué Cut 1 – Sm. Triangle Appliqué

Sm. Triangle Appliqué

Lg. Triangle Appliqué

Floral – 18674-WHT-CTN-D (¾ yd x wof / 68.58 cm x 106.68 cm) Cut 4 – 4 ½ in x 26 ½ in (11.43 cm x 67.31 cm) Cut 1 – Lg. Triangle Appliqué Cut 1 – Sm. Triangle Appliqué

Triangle Base Appliqué

Sm. Triangle Appliqué

8 in Circle Template

Deer – 18676-YLW-CTN-D (¼ yd x wof / 22.86 cm x 106.68 cm) Cut 1 – Lg. Triangle Appliqué Cut 1 – Triangle Base Appliqué Cut 1 – Sm. Triangle Appliqué Cut 1 – 8 in (20.32 cm) Circle Appliqué

Sewing 1.

Use the templates provided to trace the number of appliqué shapes on the paper side of fusible web as shown in Diagram A. Leave ¼ in (6.35 mm) between shapes and cut out 1/8 in (3.18 mm) outside the traced line.

Dia. A 8 in Circle Template Lg. Triangle Appliqués

Triangle Base Appliqués Sm. Triangle Appliqués Lightweight fusible web (17 in x 27 in / 43.18 cm x 68.58 cm) Cut 1 – 8 in (20.32 cm) Circle Appliqué Cut 3 – Triangle Base Appliqué Cut 4 – Lg. Triangle Appliqué Cut 4 – Sm. Triangle Appliqué

www.3wishesfabric.com

page 3

2.

Refer to Diagram B to place the fusible web appliqué pieces on the wrong side of each fabric, adhesive side down. Fuse according to the manufacturer’s directions. Cut out on the traced lines. Remove paper backing.

Dia. B wrong side

wrong side Lg. Triangle Appliqué

Lg. Triangle Appliqué

Sm. Triangle Appliqué

Triangle Base Appliqué

Triangle Base Appliqué

Sm. Triangle Appliqué

Deer – 18676-YLW-CTN-D Cut 1 – Lg. Triangle Appliqué Cut 1 – Triangle Base Appliqué Cut 1 – Sm. Triangle Appliqué

Tents – 18674-BLU-CTN-D Cut 1 – Lg. Triangle Appliqué Cut 1 – Triangle Base Appliqué Cut 1 – Sm. Triangle Appliqué wrong side Lg. Triangle Appliqué

Sm. Triangle Appliqué

Triangle Base Appliqué

8 in Circle Template

wrong side

Tossed Animals – 18673-PNK-CTN-D Cut 1 – Lg. Triangle Appliqué Cut 1 – Triangle Base Appliqué Cut 1 – Sm. Triangle Appliqué Cut 1 – 8 in (20.32 cm) Circle Appliqué

Lg. Triangle Appliqué Sm. Triangle Appliqué

Floral – 18674-WHT-CTN-D Cut 1 – Lg. Triangle Appliqué Cut 1 – Sm. Triangle Appliqué

3.

Refer to Diagram C to position the appliqué pieces right side up on the right side of the Circle Dots square (26 ½ in x 26 ½ in / 67.31 cm x 67.31 cm). Center the triangle tree shapes on top of each other as shown. Note: Check that appliqué pieces are at least 3/4 in (19.1 mm) away from edges and check orientation of designs. Fuse to the right side of the fabric according to the manufacturer’s directions. Use a coordinating thread and small buttonhole or zig-zag stitch to secure and finish the edges. The Center Appliqué Block should measure 26 ½ in x 26 ½ in (67.31 cm x 67.31 cm).

Center Appliqué Block

Dia. C

1 ¾ in (4.45 cm)

3 ½ in (8.89 cm) 4 ¾ in (12.07 cm)

Buttonhole stitch

3 ¼ in (8.26 cm) ¾ in (1.91 cm) 8 ¾ in (22.23 cm) 6 in (15.24 cm)

4 ¾ in (12.07 cm)

Zigzag stitch 4 ¾ in (12.07 cm)

3 ¼ in (8.26 cm) 4 ¼ in (10.8 cm)

3 ¼ in (8.26 cm) ¾ in (1.91 cm)

4 ¾ in (12.07 cm)

26 ½ in x 26 ½ in (67.31 cm x 67.31 cm)

1 ¼ in (3.18 cm)

6 3⁄8 in (16.19 cm)

www.3wishesfabric.com

page 4

4.

Place a Tossed Animals square (4 ½ in x 4 ½ in / 11.43 cm x 11.43 cm) on each side of a Floral rectangle (4 ½ in x 26 ½ in / 11.43 cm x 67.31 cm) as shown in Diagram D. Pin RST, sew and press to make the Floral Top Border (4 ½ in x 34 ½ in / 11.43 cm x 87.63 cm). Repeat to make the Floral Bottom Border. Note: Check orientation of designs.

Dia. D +

+ = Floral Top and Bottom Border

4 ½ in x 34 ½ in (11.43 cm x 87.63 cm) Make 2

5.

Place a Tossed Animals square (4 ½ in x 4 ½ in / 11.43 cm x 11.43 cm) on each side of a Arrow Patch Fussy Cut rectangle (4 ½ in x 40 ½ in / 11.43 cm x 102.87 cm) as shown in Diagram E. Pin RST, sew and press to make the Arrow Patch Top Border (4 ½ in x 48 ½ in / 11.43 cm x 123.19 cm). Note: Check orientation of designs.

Dia. E +

+ = Arrow Patch Top Border

4 ½ in x 48 ½ in (11.43 cm x 123.19 cm)

6.

Place a Tossed Animals square (4 ½ in x 4 ½ in / 11.43 cm x 11.43 cm) on each side of a Arrow Patch Fussy Cut rectangle (4 ½ in x 40 ½ in / 11.43 cm x 102.87 cm) as shown in Diagram F. Pin RST, sew and press to make the Arrow Patch Bottom Border (4 ½ in x 48 ½ in / 11.43 cm x 123.19 cm ). Note: Check orientation of designs.

Dia. F +

+ = Arrow Patch Bottom Border

4 ½ in x 48 ½ in (11.43 cm x 123.19 cm)

www.3wishesfabric.com

page 5

7.

Refer to Diagram G to place the Borders around the Center Appliqué Block (26 ½ in x 26 ½ in / 67.31 cm x 67.31 cm). Sew each Border RST in the order listed. Pin, matching center, seams and ends. Press seams as shown. Measure at each step to ensure the next border will fit. If one border is a little larger than the border it is being sewn to, pin well to ease the fullness and place the fullness on the bottom while sewing. Finished Quilt Top should measure 48 ½ in x 48 ½ in (123.19 cm x 123.19 cm).

Floral Border Sides: 2 – Floral rectangles (4 ½ in x 26 ½ in / 11.43 cm / 67.31 cm) Top and Bottom: Floral Top and Bottom Borders (4 ½ in x 34 ½ in / 11.43 cm x 87.63 cm) Quilt Top - 34 ½ in x 34 ½ in (87.63 cm x 87.63 cm) Circle Dots Border Top and Bottom: 2 – Circle Dots strips (2 in x 34 ½ in / 5.08 cm x 87.63 cm) Sides: 2 – Circle Dots strips (2 in x 37 ½ in / 5.08 cm x 95.25 cm) Quilt Top - 37 ½ in x 37 ½ in (95.25 cm x 95.25 cm) Arrow Border Top and Bottom: 2 – Arrow strips (2 in x 37 ½ in / 5.08 cm x 95.25 cm) Sides: 2 – Arrow strips (2 in x 40 ½ in / 5.08 cm x 102.87 cm) Quilt Top - 40 ½ in x 40 ½ in (102.87 cm x 102.87 cm) Arrow Patch Border Sides: 2 – Arrow Patch Fussy Cut rectangles (4 ½ in x 40 ½ in / 11.43 cm x 102.87 cm) Top and Bottom: Arrow Patch Top and Bottom Borders (4 ½ in x 48 ½ in / 11.43 cm x 123.19 cm).

Dia. G

+ + +

+

+

+

+

+

+

+

+

+

+

+ + +

48 ½ in x 48 ½ in (123.19 cm x 123.19 cm)

www.3wishesfabric.com

page 6

Finishing 8.

9.

Dia. H

Remove the selvages from the Tossed Animals Backing fabric. Cut one piece 40 ¼ in x 56 in (102.24 cm x 142.24 cm) and two pieces 16 ¼ in x 28 ¼ in (41.28 cm x 71.76 cm). Pin RST and sew the two smaller pieces on the short edges; press. Pin the two sections RST and sew along the long edges as shown in Diagram H. Press the seam open or to one side. The Backing should measure 56 in x 56 in (142.24 cm x 142.24 cm).

Press finished Quilt Top and Backing. Tape the Backing, wrong side up, to a firm surface. Layer Batting and Quilt Top (right side up). Baste the layers together with safety pins. Quilt as desired.

10. Once quilting is complete, square up corners and edges, trimming excess Backing and Batting even with the Quilt Top.

16 ¼ in x 28 ¼ in (41.28 cm x 71.76 cm)

40 ¼ in x 56 in (102.24 cm x 142.24 cm)

16 ¼ in x 28 ¼ in (41.28 cm x 71.76 cm)

Backing (Directional) 56 in x 56 in (142.24 cm x 142.24 cm)

11. Binding – Follow Diagram I to make the Tents Binding. Remove selvages and sew the short ends of the five 2 ½ in (6.35 cm) x wof strips RST end to end at a 45° angle to make one continuous strip; press seams open. Press one short end ¼ in (6.35 mm) to the wrong side. Fold in half lengthwise with wrong sides together; press. Leaving a 2 in (5.08 cm) tail on the folded end, place cut edges of folded Binding even with the edge of the Quilt Top and sew, mitering the corners. Overlap ends, trim any excess and finish sewing the Binding. Fold Binding over to back and hand stitch.

Dia. I

Stop stitching ¼ in (6.35 mm) from end of quilt

Finished Care Instructions Machine wash in cold water; gentle cycle. Do not bleach. Tip: Before drying, check for fabric dyes that may have run. If fabric dyes run, rewash and rinse using a color catcher to absorb loose dye. Lay flat to dry or tumble dry low.

www.3wishesfabric.com

©2022 3 Wishes Fabric®

page 7

Appliqué Template (100% Scale) Trace on paper side of fusible web.

Scale: 1 square = 1 in x 1 in

8 in Circle Template Cut 1 – Deer

Appliqué Template (100% Scale) Trace on paper side of fusible web.

Scale: 1 square = 1 in x 1 in

Triangle Base Template Cut 1 – Deer Cut 1 – Tents Cut 1 – Tossed Animals

Appliqué Template (100% Scale) Trace on paper side of fusible web.

Scale: 1 square = 1 in x 1 in

Lg. Triangle Template Cut 1 – Deer Cut 1 – Tents Cut 1 – Tossed Animals Cut 1 – Floral

Sm. Triangle Template Cut 1 – Deer Cut 1 – Tents Cut 1 – Tossed Animals Cut 1 – Floral

www.3wishesfabric.com

Follow us here to see more exciting projects and ideas!

Quilt Featuring the Good Vibes Collection

by Courtney Morgenstern Shipping to stores January 2022

Finished Size: 48 ½ in x 54 ½ in (123.19 cm x 138.43 cm)

Fabric Needed 3 Wishes Fabric® Good Vibes Collection • 2 3/8 yds – Circle Dots (18660-WOW-CTN-D) • 7/8 yd – Butterflies (18662-BLU-CTN-D) for Piecing and Binding • 18 in x 21 in – Floral (18657-WHT-CTN-D) • 18 in x 21 in – Color Strokes (18658-PNK-CTN-D) • 18 in x 21 in – Triangles (18659-TRQ-CTN-D) • 18 in x 21 in – Fractures (18661-MLT-CTN-D) • 18 in x 21 in – Words (18663-TRQ-CTN-D) • 18 in x 21 in – Wide Stripe (18664-MLT-CTN-D) • 18 in x 21 in – Diagonal Stripe (18665-TRQ-CTN-D) • 18 in x 21 in – Rainbows (18666-WHT-CTN-D) • 2 3/4 yds – Rainbows (18666-WHT-CTN-D) for Backing

Additional Supplies Needed: • 57 in x 63 in Cotton batting • 17 in x 108 in (3 yds) Lightweight fusible web • Tape • Piecing and sewing thread • Quilting and sewing supplies • Even-feed foot (optional for quilting)

page 1

Before You Begin Read all instructions before beginning project. Do not pre-wash fabrics. Press fabrics with a dry iron on cotton setting before cutting.

Use a ¼ in (6.35 mm) seam allowance and sew fabrics with right sides together (RST) unless otherwise noted. Press seams in the direction of the arrows. wof = width of fabric. Print Appliqué Template pages at 100% scale.

Cutting Use a rotary cutter and ruler to cut the size and number of squares and rectangles from each fabric listed below. Set aside the remaining fabric for making the appliqués.

2 ½ in x wof

16 ½ in x 18 ½ in

Butterflies – 18662-BLU-CTN-D (7⁄8 yd x wof / 80.01 cm x 106.68 cm) Cut 6 – 2 ½ in x wof (6.35 cm x 106.68 cm) for Binding Cut 1 – Lg. Arch from Template Cut 1 – Med. Arch from Template Cut 1 – Sm. Arch from Template

Floral – 18657-WHT-CTN-D (18 in x 21 in / 45.72 cm x 53.34 cm) Cut 1 – Lg. Arch from Template Cut 1 – Med. Arch from Template Cut 1 – Sm. Arch from Template

Circle Dots – 18660-WOW-CTN-D (2 3⁄8 yds x wof / 217.17 cm x 106.68 cm) Cut 9 – 16 ½ in x 18 ½ in (41.91 cm x 46.99 cm)

www.3wishesfabric.com

Color Strokes – 18658-PNK-CTN-D (18 in x 21 in / 45.72 cm x 53.34 cm) Cut 1 – Lg. Arch from Template Cut 1 – Med. Arch from Template Cut 1 – Sm. Arch from Template

page 2

Triangles – 18659-TRQ-CTN-D (18 in x 21 in / 45.72 cm x 53.34 cm) Cut 1 – Lg. Arch from Template Cut 1 – Med. Arch from Template Cut 1 – Sm. Arch from Template

Words – 18663-TRQ-CTN-D (18 in x 21 in / 45.72 cm x 53.34 cm) Cut 1 – Lg. Arch from Template Cut 1 – Med. Arch from Template Cut 1 – Sm. Arch from Template

Diagonal Stripe – 18665-TRQ-CTN-D (18 in x 21 in / 45.72 cm x 53.34 cm) Cut 1 – Lg. Arch from Template Cut 1 – Med. Arch from Template Cut 1 – Sm. Arch from Template

Fractures – 18661-MLT-CTN-D (18 in x 21 in / 45.72 cm x 53.34 cm) Cut 1 – Lg. Arch from Template Cut 1 – Med. Arch from Template Cut 1 – Sm. Arch from Template

Wide Stripe – 18664-MLT-CTN-D (18 in x 21 in / 45.72 cm x 53.34 cm) Cut 1 – Lg. Arch from Template Cut 1 – Med. Arch from Template Cut 1 – Sm. Arch from Template

Rainbows – 18666-WHT-CTN-D (18 in x 21 in / 45.72 cm x 53.34 cm) Cut 1 – Lg. Arch from Template Cut 1 – Med. Arch from Template Cut 1 – Sm. Arch from Template

Sewing 1.

Tape the four Template pages together as shown in Diagram A. Use a marking pen to connect any Arch lines that may have been covered up while taping the pattern together. Note: Do not cut out the shapes. It will be easier to trace on the fusible web as one sheet.

Dia. A

Appliqué Template (100% Scale) Trace on paper side of fusible web.

Appliqué Template (100% Scale) Trace on paper side of fusible web.

Scale: 1 square = 1 in x 1 in

Scale: 1 square = 1 in x 1 in

Med. Arch Note: Fabric direction Cut 1 – Butterflies Cut 1 – Floral Cut 1 – Color Strokes Cut 1 – Triangles Cut 1 – Fractures Cut 1 – Words Cut 1 – Wide Stripes Cut 1 – Diagonal Stripes Cut 1 – Rainbows

Sm. Arch Note: Fabric direction Cut 1 – Butterflies Cut 1 – Floral Cut 1 – Color Strokes Cut 1 – Triangles Cut 1 – Fractures Cut 1 – Words Cut 1 – Wide Stripes Cut 1 – Diagonal Stripes Cut 1 – Rainbows

Center

¼ in Overlap Med. Arch Template Side 2 1

Center

Center

Center

Appliqué Template (100% Scale) Trace on paper side of fusible web.

¼ in Overlap Sm. Arch Template Side 2

Lg. Arch Template Top Side 1

Scale: 1 square = 1 in x 1 in Med. Arch Template Side 1

¼ in Overlap Lg. Arch Template Top

Center

¼ in Overlap Lg. Arch Template Top – Center

Lg. Arch Note: Fabric direction Cut 1 – Butterflies Cut 1 – Floral Cut 1 – Color Strokes Cut 1 – Triangles Cut 1 – Fractures Cut 1 – Words Cut 1 – Wide Stripes Cut 1 – Diagonal Stripes Cut 1 – Rainbows

Lg. Arch Template Top Side 2

¼ in Overlap Lg.Arch ArchTemplate TemplateSide Top2 Lg.

Lg. Arch Template Side 1

Med. Arch Template Side 2

Sm. Arch Template Side 2

Sm. Arch Template Side 1

Lg. Arch Template Side 2

Med. Arch Template Side 1

2.

Appliqué Template (100% Scale) Trace on paper side of fusible web.

Scale: 1 square = 1 in x 1 in Med. Arch Template Side 2

Use the Template from Step 1 to trace nine groups of Rainbow Arches on the paper side of fusible web as shown in Diagram B. Leave ¼ in (6.35 mm) between groups and cut out each individual Arch 1/8 in (3.18 mm) outside the traced line for a total of nine Large, nine Medium and nine Small Arches.

Dia. B

Lightweight fusible web (17 in x 108 in / 43.18 cm x 274.32 cm) Cut 9 – Lg. Arch from Template Cut 9 – Med. Arch from Template Cut 9 – Sm. Arch from Template

www.3wishesfabric.com

page 3

3.

Refer to Diagram C to place the adhesive side of the fusible web appliqué shapes on the wrong side of each fabric. Fuse according to the manufacturer’s directions. Cut out on the traced lines. To mark the center, fold and finger press along the center line before removing the paper backing.

Dia. C

Butterflies Cut 1 – Lg. Arch from Template Cut 1 – Med. Arch from Template Cut 1 – Sm. Arch from Template

Floral Cut 1 – Lg. Arch from Template Cut 1 – Med. Arch from Template Cut 1 – Sm. Arch from Template

Color Strokes Cut 1 – Lg. Arch from Template Cut 1 – Med. Arch from Template Cut 1 – Sm. Arch from Template

Triangles Cut 1 – Lg. Arch from Template Cut 1 – Med. Arch from Template Cut 1 – Sm. Arch from Template

Fractures Cut 1 – Lg. Arch from Template Cut 1 – Med. Arch from Template Cut 1 – Sm. Arch from Template

Words Cut 1 – Lg. Arch from Template Cut 1 – Med. Arch from Template Cut 1 – Sm. Arch from Template

Wide Stripe Cut 1 – Lg. Arch from Template Cut 1 – Med. Arch from Template Cut 1 – Sm. Arch from Template

Diagonal Stripe Cut 1 – Lg. Arch from Template Cut 1 – Med. Arch from Template Cut 1 – Sm. Arch from Template

Rainbows Cut 1 – Lg. Arch from Template Cut 1 – Med. Arch from Template Cut 1 – Sm. Arch from Template

www.3wishesfabric.com

page 4

4.

Refer to Diagram D to prepare the Block background by folding a Circle Dots rectangle 16 ½ in x 18 ½ in ( 41.91 cm x 46.99 cm) in half as shown; press gently to crease the center. Position the Rainbows Lg. Arch on the right side of the background matching centers and aligning the bottom edges. Repeat with the Butterflies Med. Arch and Floral Sm. Arch. Fuse to the right side of the fabric according to the manufacturer’s directions. Use a coordinating thread and small buttonhole or zig-zag stitch to secure and finish the edges. Block 1 should measure 16 ½ in x 18 ½ in (41.91 cm x 46.99 cm). Label each Block as they are made.

Dia. D

Center fold

Block 1 Lg. Arch – Rainbows Med. Arch – Butterflies Sm. Arch – Floral

Match centers Buttonhole stitch Zigzag stitch

Align bottom edges

5.

16 ½ in x 18 ½ in (41.91 cm x 46.99 cm)

Follow Step 4 and Diagram E to make Blocks 2-9, each measuring 16 ½ in x 18 ½ in (41.91 cm x 46.99 cm); label.

Dia. E Block 2

Block 3

Block 4

Block 5

Lg. Arch – Color Strokes Med. Arch – Rainbows Sm. Arch – Butterflies

Lg. Arch – Words Med. Arch – Diagonal Stripe Sm. Arch – Wide Stripe

Lg. Arch – Triangles Med. Arch – Floral Sm. Arch – Diagonal Stripe

Lg. Arch – Wide Stripe Med. Arch – Words Sm. Arch – Triangles

16 ½ in x 18 ½ in (41.91 cm x 46.99 cm)

16 ½ in x 18 ½ in (41.91 cm x 46.99 cm)

16 ½ in x 18 ½ in (41.91 cm x 46.99 cm)

16 ½ in x 18 ½ in (41.91 cm x 46.99 cm)

Block 6

Block 7

Block 8

Block 9

Lg. Arch – Butterflies Med. Arch – Fractures Sm. Arch – Color Strokes

Lg. Arch – Floral Med. Arch – Color Strokes Sm. Arch – Fractures

Lg. Arch – Diagonal Stripe Med. Arch – Wide Stripe Sm. Arch – Words

Lg. Arch – Fractures Med. Arch – Triangles Sm. Arch – Rainbows

16 ½ in x 18 ½ in (41.91 cm x 46.99 cm)

16 ½ in x 18 ½ in (41.91 cm x 46.99 cm)

16 ½ in x 18 ½ in (41.91 cm x 46.99 cm)

16 ½ in x 18 ½ in (41.91 cm x 46.99 cm)

www.3wishesfabric.com

page 5

6.

Refer to Diagram F to place the Blocks in three rows. Pin Blocks 1 and 2 RST, sew and press. Add Block 3 to complete Row 1.

Repeat for remaining rows. Pin the Rows RST matching seams; sew and press. The finished Quilt Top should measure 48 ½ in x 54 ½ in (123.19 cm x 138.43 cm).

Dia. F

Good Vibes Quilt Top Block 2

Block 1

Row 1

+

+

+ Block 5

Block 4

Row 2

Block 3

+

Block 6

+

+ Block 7

Block 8

Block 9

Row 3

48 ½ in x 54 ½ in (123.19 cm x 138.43 cm)

www.3wishesfabric.com

page 6

Finishing 7.

Dia. G

Remove the selvages from the Rainbows Backing fabric. Cut one piece 40 ¼ in x 63 in (102.24 cm x 160.02 cm) and two pieces 17 ¼ in x 31 ¾ in (43.82 cm x 80.65 cm). Note: Check the orientation of the designs. Pin RST and sew the two smaller pieces on the short edges; press. Pin the two sections RST and sew along the long edges as shown in Diagram G. Press the seam open or to one side.

The Backing should measure 57 in x 63 in (144.78 cm x 160.02 cm).

8.

Press finished Quilt Top and Backing. Tape the Backing wrong side up to a firm surface. Layer Batting and Quilt Top (right side up).

Baste the layers together with safety pins. Quilt as desired.

9.

Once quilting is complete, square up corners and edges, trimming excess Backing and Batting even with the Quilt Top.

17 ¼ in x 31 ¾ in (43.82 cm x 80.65 cm)

40 ¼ in x 63 in (102.24 cm x 160.02 cm)

17 ¼ in x 31 ¾ in (43.82 cm x 80.65 cm)

Backing 57 in x 63 in (144.78 cm x 160.02 cm)

10. Binding – Follow Diagram H to make the Butterflies Binding. Remove selvages and sew the short ends of the six 2 ½ in (6.35 cm) x wof strips RST end to end at a 45° angle to make one continuous strip; press seams open. Press one short end ¼ in (6.35 mm) to the wrong side. Fold in half lengthwise with wrong sides together; press. Leaving a 2 in (5.08 cm) tail on the folded end, place cut edges of folded Binding even with the edge of the Quilt Top and sew, mitering the corners. Overlap ends, trim any excess and finish sewing the Binding. Fold Binding over to back and hand stitch.

Dia. H

Stop stitching ¼ in (6.35 mm) from end of quilt

Finished Care Instructions Machine wash in cold water; gentle cycle. Do not bleach. Tip: Before drying, check for fabric dyes that may have run. If fabric dyes run, rewash and rinse using a color catcher to absorb loose dye. Lay flat to dry or tumble dry low.

www.3wishesfabric.com

©2022 3 Wishes Fabric®

page 7

Sm. Arch Template Side 1

Med. Arch Template Side 1

Lg. Arch Template Side 1

Center

¼ in Overlap Med. Arch Template Side 2

¼ in Overlap Lg. Arch Template Top

Center

Scale: 1 square = 1 in x 1 in

¼ in Overlap Sm. Arch Template Side 2

Appliqué Template (100% Scale) Trace on paper side of fusible web.

¼ in Overlap Med. Arch Template Side 1

Center

¼ in Overlap Sm. Arch Template Side 2

Center

Appliqué Template (100% Scale) Trace on paper side of fusible web.

Scale: 1 square = 1 in x 1 in ¼ in Overlap Lg. Arch Template Top

Med. Arch Template Side 2

Sm. Arch Template Side 2

Lg. Arch Template Side 2

Appliqué Template (100% Scale) Trace on paper side of fusible web.

Scale: 1 square = 1 in x 1 in

Med. Arch Note: Fabric direction Cut 1 – Butterflies Cut 1 – Floral Cut 1 – Color Strokes Cut 1 – Triangles Cut 1 – Fractures Cut 1 – Words Cut 1 – Wide Stripes Cut 1 – Diagonal Stripes Cut 1 – Rainbows

Sm. Arch Note: Fabric direction Cut 1 – Butterflies Cut 1 – Floral Cut 1 – Color Strokes Cut 1 – Triangles Cut 1 – Fractures Cut 1 – Words Cut 1 – Wide Stripes Cut 1 – Diagonal Stripes Cut 1 – Rainbows

Lg. Arch Template Top Side 1

¼ in Overlap Lg. Arch Template Top

¼ in Overlap Lg. Arch Template Top – Center

Lg. Arch Note: Fabric direction Cut 1 – Butterflies Cut 1 – Floral Cut 1 – Color Strokes Cut 1 – Triangles Cut 1 – Fractures Cut 1 – Words Cut 1 – Wide Stripes Cut 1 – Diagonal Stripes Cut 1 – Rainbows

Appliqué Template (100% Scale) Trace on paper side of fusible web.

Scale: 1 square = 1 in x 1 in

Center

¼ in Overlap Lg. Arch Template Top – Center

Lg. Arch Template Top Side 2

¼ in Overlap Lg. Arch Template Side 2

www.3wishesfabric.com

Follow us here to see more exciting projects and ideas!

Quilt Featuring the Hometown America Collection

by Beth Albert and the Good Vibes Collection

by Courtney Morgenstern Shipping to stores January 2022

Finished Size: 42 ½ in x 61 ½ in (107.95 cm x 156.21 cm)

Fabric Needed 3 Wishes Fabric® Hometown America Collection • 1 Panel – Panel (18696-PNL-CTN-D) • 7/8 yd – Hearts (18694-RED-CTN-D) for Piecing and Binding • 1/3 yd – Tossed Fruit (18693-BGE-CTN-D) • 1/3 yd – Trucks (18698-NVY-CTN-D) • 1/3 yd – Cows (18701-BLU-CTN-D) • 1/4 yd – Patch (18699-BGE-CTN-D) • 1/8 yd – Flowers (18700-WHT-CTN-D) • 2 5/8 yds – Campers (18702-BGE-CTN-D) Backing

Additional Supplies Needed: • 50 in x 70 in (127 cm x 177.8 cm) Cotton batting • 17 in x 9 in (43.18 cm x 22.86 cm) Lightweight fusible web • Piecing and sewing thread • Quilting and sewing supplies • Even-feed foot (optional for quilting)

3 Wishes Fabric® Good Vibes Collection • 3/4 yd – Circle Dots (18660-WOW-CTN-D)

page 1

Before You Begin Read all instructions before beginning project. Do not pre-wash fabrics. Press fabrics with a dry iron on cotton setting before cutting.

Use a ¼ in (6.35 mm) seam allowance and sew fabrics with right sides together (RST) unless otherwise noted. Press seams in the direction of the arrows. wof = width of fabric. Print appliqué template page at 100% scale.

Note: A printed panel may become slightly skewed during the finishing process. Check if panel is square before cutting by folding the panel so selvages meet. If all edges do not meet, pull firmly from corner to corner until the edges meet. Continue until all corners are square.

Cutting Use a rotary cutter and ruler to cut the size and number of squares and rectangles from each fabric listed below. Set aside the remaining fabric for making the appliqués.

2 in x 35 ½ in 2 in x 32 ½ in 2 in x 27 ½ in 2 in x 17 ¾ in 2 ½ in x 2 ½ in 32 ½ in x 32 ½ in

Star Templates

Panel – 18696-PNL-CTN-D (1 yd x wof / 91.44 cm x 106.68 cm) Fussy Cut 1 – 32 ½ in x 32 ½ in (82.55 cm x 82.55 cm)

Circle Dots – 18660-WOW-CTN-D (¾ yd x wof / 68.58 cm x 106.68 cm) from the 3W Good Vibes Collection Cut 2 – 2 in x 35 ½ in (5.08 cm x 90.17 cm) Cut 2 – 2 in x 32 ½ in (5.08 cm x 82.55 cm) Cut 2 – 2 in x 27 ½ in (5.08 cm x 69.85 cm) Cut 4 – 2 in x 17 ¾ in (10.16 cm x 45.09 cm) Cut 10 – 2 ½ in x 2 ½ in (6.35 cm x 6.35 cm) Cut 3 – Stars from Template 4 in x 35 ½ in

2 ½ in x wof

Tossed Fruit – 18693-BGE-CTN-D (1⁄3 yd x wof / 30.48 cm x 106.68 cm) Cut 2 – 4 in x 35 ½ in (10.16 cm x 90.17 cm) 2 in x 27 ½ in 8 in x 8 in 2 in x 17 ¾ in

Trucks – 18698-NVY-CTN-D (1⁄3 yd x wof / 30.48 cm x 106.68 cm) Cut 3 – 8 in x 8 in (20.32 cm x 20.32 cm) Hearts – 18694-RED-CTN-D (7⁄8 yd x wof / 80.01 cm x 106.68 cm) Cut 6 – 2 ½ in x wof (6.35 cm x 106.68 cm) for Binding Cut 3 – 2 in x 27 ½ in (5.08 cm x 69.85 cm) Cut 6 – 2 in x 17 ¾ in (5.08 cm x 45.09 cm)

3 in x 42 ½ in

Cows – 18701-BLU-CTN-D (1⁄3 yd x wof / 30.48 cm x 107.95 cm) Fussy Cut 2 – 3 in x 42 ½ in (7.62 cm x 107.95 cm)

www.3wishesfabric.com

page 2

2 ½ in x 2 ½ in 4 ½ in x 42 ½ in

Flowers – 18700-WHT-CTN-D (1⁄8 yd x wof / 11.43 cm x 106.68 cm) Cut 11 – 2 ½ in x 2 ½ in (6.35 cm x 6.35 cm)

Patch – 18699-BGE-CTN-D (¼ yd x wof / 22.86 cm x 107.95 cm) Fussy Cut 1 – 4 ½ in x 42 ½ in (7.62 cm x 107.95 cm)

Sewing 1.

Use the templates provided to trace three Star appliqué shapes on the paper side of lightweight fusible web as shown in Diagram A. Leave ¼ in (6.35 mm) between shapes and cut out 1/8 in (3.18 mm) outside the traced line.

Dia. A

Star Templates Lightweight fusible web (17 in x 9 in / 43.18 cm x 22.86 cm) Cut 3 – Stars from Template

2.

Refer to Diagram B to place the fusible web appliqué pieces on the wrong side of the Circle Dots fabric, adhesive side down. Fuse according to the manufacturer’s directions. Cut out on the traced lines. Remove paper backing.

Dia. B

wrong side Star Templates

Circle Dots Cut 3 – Stars from Template

3.

Refer to Diagram C to center one Star appliqué on one Trucks square (8 in x 8 in / 20.32 cm x 20.32 cm). Fuse to the right side of the fabric according to the manufacturer’s directions. Use a coordinating thread and small buttonhole or zig-zag stitch to secure and finish the edges. The Star Block should measure 8 in x 8 in (20.32 cm x 20.32 cm). Make three.

Dia. C Star Block

Buttonhole stitch Zigzag stitch 8 in x 8 in (20.32 cm x 20.32 cm) Make 3

4.

Place three Hearts and two Circle Dots rectangles (2 in x 17 ¾ in / 5.08 cm x 45.09 cm) as shown in Diagram D. Pin RST, sew and press to make one Row 1 Unit (8 in x 17 ¾ in / 20.32 cm x 45.09 cm). Make two.

Dia. D +

Row 1 Unit

+ = + +

www.3wishesfabric.com

8 in x 17 ¾ in (20.32 cm x 45.09 cm) Make 2

page 3

5.

Place three Hearts and two Circle Dots rectangles (2 in x 27 ½ in / 5.08 cm x 69.85 cm) as shown in Diagram E. Pin RST, sew and press to make one Row 6 Unit (8 in x 27 ½ in / 20.32 cm x 69.85 cm).

Dia. E +

Row 6 Unit

+ =

=

+ 8 in x 27 ½ in (20.32 cm x 69.85 cm)

+

6.

Place a Row 1 Unit (8 in x 17 ¾ in / 20.32 cm x 45.72 cm) on each side of the Star Block (8 in x 8 in / 20.32 cm x 20.32 cm) as shown in Diagram F. Pin RST, sew and press to make Row 1 (8 in x 42 ½ in / 20.32 cm x 107.95 cm).

Dia. F

+

+

= Row 1

8 in x 42 ½ in (20.32 cm x 107.95 cm)

7.

Place a Star Block (8 in x 8 in / 20.32 cm x 20.32 cm) on each side of the Row 6 Unit (8 in x 27 ½ in / 20.32 cm x 69.85 cm) as shown in Diagram G. Pin RST, sew and press to make Row 6 (8 in x 42 ½ in / 20.32 cm x 107.95 cm).

Dia. G

+

+

= Row 6

8 in x 42 ½ in (20.32 cm x 107.95 cm)

www.3wishesfabric.com

page 4

8.

Alternate the eleven Flowers and the ten Circle Dots squares (2 ½ in x 2 ½ in / 6.35 cm x 6.35 cm) as shown in Diagram H. Pin RST, sew and press to make Row 2 (2 ½ in x 42 ½ in / 6.35 cm x 107.95 cm).

Dia. H +

+

+

+

+

+

+

+

+

+

+

+

+

+

+

+

+

+

+

+

= Row 2

2 ½ in x 42 ½ in (6.35 cm x 107.95 cm)

9.

Refer to Diagram I to make the Center Unit. Place a Circle Dots strip (2 in x 32 ½ in / 5.08 cm x 82.55 cm) on each side of the Fussy Cut Panel square (32 ½ in x 32 ½ in / 82.55 cm x 82.55 cm). Pin RST matching ends and centers, sew and press. Place a Circle Dots Strip (2 in x 35 ½ in / 5.08 cm x 90.17 cm) on the top and bottom. Pin RST matching ends and centers, sew and press. Place a Tossed Fruit rectangle (4 in x 35 ½ in / 10.16 cm x 90.17 cm) on each side. Pin RST matching ends and centers, sew and press.

The Center Unit should measure 35 ½ in x 42 ½ in (90.17 cm x 107.95 cm).

Dia. I +

+

+

+

+

+ = Center Unit

35 ½ in x 42 ½ in (90.17 cm x 107.95 cm)

www.3wishesfabric.com

page 5

10. Place the Rows as shown in Diagram J: Row 1: Made in Step 6 (8 in x 42 ½ in / 20.32 cm x 107.95 cm).

Row 2: Made in Step 8 (2 ½ in x 42 ½ in / 6.35 cm x 107.95 cm).

Row 3: Fussy Cut Cows rectangle (3 in x 42 ½ in / 7.62 cm x 107.95 cm).

Center Unit: Made in Step 9 (35 ½ in x 42 ½ in / 90.17 cm x 107.95 cm).

Row 4: Fussy Cut Cows rectangle (3 in x 42 ½ in / 7.62 cm x 107.95 cm).

Row 5: Fussy Cut Patch rectangle (4 ½ in x 42 ½ in / 11.43 cm x 107.95 cm).

Row 6: Made in Step 7 (8 in x 42 ½ in / 20.32 cm x 107.95 cm).

Pin RST matching ends and centers; sew and press.

The Hometown America Quilt Top should measure 42 ½ in x 61 ½ in (107.95 cm x 156.21 cm).

Dia. J

Hometown America Quilt Top

Row 1

+ Row 2 + Row 3 +

Center Unit

+ Row 4 + Row 5 + Row 6

42 ½ in x 61 ½ in (107.95 cm x 156.21 cm)

www.3wishesfabric.com

page 6

Finishing 11. Remove the selvages from the Campers Backing fabric.

Note: Check orientation of the design. Cut two pieces 10 ½ in x 17 ¾ in (26.67 cm x 45.09 cm), two pieces 10 ½ in x 18 in (26.67 cm x 45.72 cm) and two pieces 20 ¼ in x 70 in (51.44 cm x 177.8 cm). Pin the four smaller pieces RST and sew the short edges as shown in Diagram K; press. Pin the larger pieces on each side and sew along the long edges. Press seams open or to one side. The Backing should measure 50 in x 70 in (127 cm x 177.8 cm).

Dia. K

10 ½ in x 17 ¾ in (26.67 cm x 45.09 cm)

10 ½ in x 18 in

12. Press finished Quilt Top and Backing. Tape the Backing, wrong side up, to a firm surface. Layer Batting and Quilt Top (right side up). Baste the layers together with safety pins. Quilt as desired.

13. Once quilting is complete, square up corners and edges, trimming excess Backing and Batting even with the Quilt Top.

(26.67 cm x 45.72 cm) 20 ¼ in x 70 in (51.44 cm x 177.8 cm)

20 ¼ in x 70 in (51.44 cm x 177.8 cm) 10 ½ in x 18 in (26.67 cm x 45.72 cm)

10 ½ in x 17 ¾ in (26.67 cm x 45.09 cm) Backing 50 in x 70 in (127 cm x 177.8 cm)

14. Binding – Follow Diagram L to make the Hearts Binding. Remove selvages and sew the short ends of the six 2 ½ in (6.35 cm) x wof strips RST end to end at a 45° angle to make one continuous strip; press seams open. Press one short end ¼ in (6.35 mm) to the wrong side. Fold in half lengthwise with wrong sides together; press. Leaving a 2 in (5.08 cm) tail on the folded end, place cut edges of folded Binding even with the edge of the Quilt Top and sew, mitering the corners. Overlap ends, trim any excess and finish sewing the Binding. Fold Binding over to back and hand stitch.

Dia. L

Stop stitching ¼ in (6.35 mm) from end of quilt

Finished Care Instructions Machine wash in cold water; gentle cycle. Do not bleach. Tip: Before drying, check for fabric dyes that may have run. If fabric dyes run, rewash and rinse using a color catcher to absorb loose dye. Lay flat to dry or tumble dry low.

www.3wishesfabric.com

©2022 3 Wishes Fabric®

page 7

Appliqué Template (100% Scale) Trace on paper side of fusible web.

Scale: 1 square = 1 in x 1 in

Star Template Cut 3 – Circle Dots

www.3wishesfabric.com

Follow us here to see more exciting projects and ideas!

Quilt Featuring the Moonlight Collection

by Jennifer Ellory and the Good Vibes Collection

by Courtney Morgenstern Shipping to stores January 2022

Finished Size: 64 ½ in x 64 ½ in (163.83 cm x 163.83 cm)

Fabric Needed 3 Wishes Fabric® Moonlight Collection • 1 1/8 yds – Celestial (18703-WHT-CTN-D) • 1 1/8 yds – Crescent Moon (18711-BLK-CTN-D) • 1 yd – Ethereal (18709-MLN-CTN-D) for Piecing and Binding • 7/8 yd – Constellation (18706-TRQ-CTN-D) • 5/8 yd – Zodiac (18704-BLK-CTN-D) • 1/3 yd – Floral Moon (18708-TRQ-CTN-D) • 1/4 yd – Moon Phases (18705-PLM-CTN-D) • 1/4 yd – Color Patch (18707-MLT-CTN-D) • 1/4 yd – Triangles (18710-PUR-CTN-D) • 1/4 yd – Floral (18712-PNK-CTN-D) • 4 1/4 yds – Moon Phases (18705-PLM-CTN-D) for Backing

Additional Supplies Needed: • 72 in x 72 in (182.88 cm x 182.88 cm) Cotton batting • 17 in x 18 in (43.18 cm x 45.72 cm) Lightweight fusible web • Tape • Piecing and sewing thread • Quilting and sewing supplies • Even-feed foot (optional for quilting)

3 Wishes Fabric® Good Vibes Collection • 1 yd – Circle Dots (18660-WOW-CTN-D)

page 1

Before You Begin

Read all instructions before beginning project. Do not pre-wash fabrics. Note: Take special care pressing metallic fabrics. Always press on the wrong side or use a pressing cloth. Press fabrics with a dry iron on cotton setting before cutting. Use a ¼ in (6.35 mm) seam allowance and sew fabrics with right sides together (RST) unless otherwise noted. Press seams in the direction of the arrows. wof = width of fabric. Print appliqué template pages at 100% scale.

Cutting Use a rotary cutter and ruler to cut the size and number of squares and rectangles from each fabric listed below. Set aside the remaining fabric for making the appliqués.

2 ½ in x wof 9 in x 9 in

4 ½ in x 4 ½ in

8 ½ in x 8 ½ in

Full Moon Appliqué

Waning Moon Appliqué

Half Moon Appliqué

Celestial – 18703-WHT-CTN-D (1 1⁄8 yds x wof / 102.87 cm x 106.68 cm) Cut 8 – 9 in x 9 in (22.86 cm x 22.86 cm) Cut 8 – 8 ½ in x 8 ½ in (21.59 cm x 21.59 cm)

9 in x 9 in

Crescent Moon Appliqué

Ethereal – 18709-MLN-CTN-D (1 yd x wof / 91.44 cm x 106.68 cm) Cut 7 – 2 ½ in x wof (6.35 cm x 106.68 cm) for Binding Cut 4 – 4 ½ in x 4 ½ in (11.43 cm x 11.43 cm) Cut 1 – Full Moon from Template Cut 1 – Waning Moon from Template Cut 1 – Half Moon from Template Cut 1 – Crescent Moon from Template

4 ½ in x 8 ½ in

4 ½ in x 4 ½ in

8 ½ in x 8 ½ in

5 in x 5 in

4 ½ in x 4 ½ in 2 ½ in x 2 ½ in

Crescent Moon – 18711-BLK-CTN-D (1 1⁄8 yds x wof / 102.87 cm x 106.68 cm) Cut 8 – 9 in x 9 in (22.86 cm x 22.86 cm) Cut 6 – 8 ½ in x 8 ½ in (21.59 cm x 21.59 cm) Cut 2 – 5 in x 5 in (12.7 cm x 12.7 cm) Cut 2 – 4 ½ in x 4 ½ in (11.43 cm x 11.43 cm)

www.3wishesfabric.com

Circle Dots – 18660-WOW-CTN-D (1 yd x wof / 91.44 cm x 106.68 cm) from the 3W Good Vibes Collection Cut 16 – 4 ½ in x 8 ½ in (11.43 cm x 21.59 cm) Cut 16 – 4 ½ in x 4 ½ in (11.43 cm x 11.43 cm) Cut 32 – 2 ½ in x 2 ½ in (6.35 cm x 6.35 cm)

page 2

4 ½ in x 4 ½ in

5 in x 5 in

4 ½ in x 4 ½ in Moon Phase – 18705-PLM-CTN-D (¼ yd x wof / 22.86 cm x 106.68 cm) Cut 8 – 4 ½ in x 4 ½ in (11.43 cm x 11.43 cm) 2 ½ in x 4 ½ in

4 ½ in x 4 ½ in

Color Patch – 18707-MLT-CTN-D (¼ yd x wof / 22.86 cm x 106.68 cm) Cut 8 – 4 ½ in x 4 ½ in (11.43 cm x 11.43 cm) 2 ½ in x 2 ½ in 4 ½ in x 4 ½ in Constellation – 18706-TRQ-CTN-D (7⁄8 yd x wof / 80.01 cm x 106.68 cm) Cut 2 – 5 in x 5 in (12.7 cm x 12.7 cm) Cut 26 – 4 ½ in x 4 ½ in (11.43 cm x 11.43 cm) Cut 16 – 2 ½ in x 4 ½ in (6.35 cm x 11.43 cm) Cut 16 – 2 ½ in x 2 ½ in (6.35 cm x 6.35 cm)

Triangles – 18710-PUR-CTN-D (¼ yd x wof / 22.86 cm x 106.68 cm) Cut 8 – 4 ½ in x 4 ½ in (11.43 cm x 11.43 cm) 4 ½ in x 4 ½ in

8 ½ in x 8 ½ in

4 ½ in x 4 ½ in

5 in x 5 in

Floral – 18712-PNK-CTN-D (¼ yd x wof / 22.86 cm x 106.68 cm) Cut 8 – 4 ½ in x 4 ½ in (11.43 cm x 11.43 cm)

Zodiac – 18704-BLK-CTN-D (5⁄8 yd x wof / 57.15 cm x 106.68 cm) Cut 6 – 8 ½ in x 8 ½ in (21.59 cm x 21.59 cm) Cut 2 – 5 in x 5 in (12.7 cm x 12.7 cm) Cut 2 – 4 ½ in x 4 ½ in (11.43 cm x 11.43 cm) 5 in x 5 in

4 ½ in x 4 ½ in

Floral Moon – 18708-TRQ-CTN-D (1⁄3 yd x wof / 30.48 cm x 106.68 cm) Cut 2 – 5 in x 5 in (12.7 cm x 12.7 cm) Cut 10 – 4 ½ in x 4 ½ in (11.43 cm x 11.43 cm)

Sewing 1.

Refer to Diagram A to make Flying Geese Units. Draw a diagonal line on the wrong side of a Circle Dots square (2 ½ in x 2 ½ in / 6.35 cm x 6.35 cm). Place RST on the left side of a Constellation rectangle (2 ½ in x 4 ½ in / 6.35 cm x 11.43 cm). Sew on the diagonal line. Trim seam to ¼ in (6.35 mm); press. Repeat with a second Circle Dots square (2 ½ in x 2 ½ in / 6.35 cm x 6.35 cm) on the right side of the rectangle to make a Constellation Flying Geese Unit (2 ½ in x 4 ½ in / 6.35 cm x 11.43 cm). Make sixteen.

Dia. A Constellation Flying Geese Unit

¼ in (6.35 mm)

Draw wrong side

www.3wishesfabric.com

Sew

Cut

Press

2 ½ in x 4 ½ in (6.35 cm x 11.43 cm) Make 16

page 3

2.

Refer to Diagram B and Step 1 to make the following Flying Geese Units:

Dia. B

Floral Flying Geese Unit

Use eight Floral squares (4 ½ in x 4 ½ in / 11.43 cm x 11.43 cm) and four Circle Dots rectangles (4 ½ in x 8 ½ in / 11.43 cm x 21.59 cm) to make four Floral Flying Geese Units (4 ½ in x 8 ½ in / 11.43 cm x 21.59 cm).

4 ½ in x 8 ½ in (11.43 cm x 21.59 cm) Make 4

Use eight Triangles squares (4 ½ in x 4 ½ in / 11.43 cm x 11.43 cm) and four Circle Dots rectangles (4 ½ in x 8 ½ in / 11.43 cm x 21.59 cm) to make four Triangles Flying Geese Units (4 ½ in x 8 ½ in / 11.43 cm x 21.59 cm).

Triangles Flying Geese Unit

4 ½ in x 8 ½ in (11.43 cm x 21.59 cm) Make 4 Color Patch Flying Geese Unit

Use eight Color Patch squares (4 ½ in x 4 ½ in / 11.43 cm x 11.43 cm) and four Circle Dots rectangles (4 ½ in x 8 ½ in / 11.43 cm x 21.59 cm) to make four Color Patch Flying Geese Units (4 ½ in x 8 ½ in / 11.43 cm x 21.59 cm).

4 ½ in x 8 ½ in (11.43 cm x 21.59 cm) Make 4 Moon Phases Flying Geese Unit

Use eight Moon Phases squares (4 ½ in x 4 ½ in / 11.43 cm x 11.43 cm) and four Circle Dots rectangles (4 ½ in x 8 ½ in / 11.43 cm x 21.59 cm) to make four Moon Phases Flying Geese Units (4 ½ in x 8 ½ in / 11.43 cm x 21.59 cm).

4 ½ in x 8 ½ in (11.43 cm x 21.59 cm) Make 4

3.

4.

Place an Ethereal square (4 ½ in x 4 ½ in / 11.43 cm x 11.43 cm), four Constellation squares (2 ½ in x 2 ½ in / 6.35 cm x 6.35 cm) and four Constellation Flying Geese Units (2 ½ in x 4 ½ in / 6.35 cm x 11.43 cm) in three rows as shown in Diagram C. Pin the pieces in each row RST, sew and press. Pin the rows RST matching seams, sew and press to make a Constellation Star Unit (8 ½ in x 8 ½ in / 21.59 cm x 21.59 cm). Make four.

Dia. C Row 1

+

Constellation Star Unit

+ +

Row 2

+

+

=

= +

Row 3

+

8 ½ in x 8 ½ in (21.59 cm x 21.59 cm) Make 4

+

Place a Constellation Star Unit (8 ½ in x 8 ½ in / 21.59 cm x 21.59 cm), four Circle Dots squares (4 ½ in x 4 ½ in / 11.43 cm x 11.43 cm) and four Floral Flying Geese Units (4 ½ in x 8 ½ in / 11.43 cm x 21.59 cm) in three rows as shown in Diagram D. Pin the pieces in each row RST, sew and press. Pin the rows RST matching seams, sew and press to make the Floral Star Block (16 ½ in x 16 ½ in / 41.91 cm x 41.91 cm).

Dia. D Row 1

+

+

Floral Star Unit +

Row 2

+

+

=

=

+ Row 3

www.3wishesfabric.com

+

+

16 ½ in x 16 ½ in (41.91 cm x 41.91 cm)

page 4

5.

Refer to Diagram E and Step 4 to make the Triangles Star Block (16 ½ in x 16 ½ in / 41.91 cm x 41.91 cm) using one Constellation Star Unit (8 ½ in x 8 ½ in / 21.59 cm x 21.59 cm), four Circle Dots squares (4 ½ in x 4 ½ in / 11.43 cm x 11.43 cm) and four Triangles Flying Geese Units (4 ½ in x 8 ½ in / 11.43 cm x 21.59 cm).

Dia. E Triangles Star Unit

16 ½ in x 16 ½ in (41.91 cm x 41.91 cm)

6.

Refer to Diagram F and Step 4 to make the Color Patch Star Block (16 ½ in x 16 ½ in / 41.91 cm x 41.91 cm) using one Constellation Star Unit (8 ½ in x 8 ½ in / 21.59 cm x 21.59 cm), four Circle Dots squares (4 ½ in x 4 ½ in / 11.43 cm x 11.43 cm) and four Color Patch Flying Geese Units (4 ½ in x 8 ½ in / 11.43 cm x 21.59 cm).

Dia. F Color Patch Star Unit

16 ½ in x 16 ½ in (41.91 cm x 41.91 cm)

7.

Refer to Diagram G and Step 4 to make the Moon Phases Star Block (16 ½ in x 16 ½ in / 41.91 cm x 41.91 cm) using one Constellation Star Unit (8 ½ in x 8 ½ in / 21.59 cm x 21.59 cm), four Circle Dots squares (4 ½ in x 4 ½ in / 11.43 cm x 11.43 cm) and four Moon Phases Flying Geese Units (4 ½ in x 8 ½ in / 11.43 cm x 21.59 cm).

Dia. G Moon Phases Star Unit

16 ½ in x 16 ½ in (41.91 cm x 41.91 cm)

8.

Draw a diagonal line on the wrong side of a Celestial square (9 in x 9 in / 22.86 cm x 22.86 cm) as shown in Diagram H. Place on top of a Crescent Moon square (9 in x 9 in / 22.86 cm x 22.86 cm) RST and sew ¼ in (6.35 mm) away from the line on both sides.

Cut on the drawn line; press; trim if necessary. Note: Two squares yield two Half-Square Triangle Units. Repeat to make a total of sixteen Half-Square Triangle 1 Units (8 ½ in x 8 ½ in / 21.59 cm x 21.59 cm). ¼ in (6.35 mm)

Dia. H

Draw wrong side

www.3wishesfabric.com

Sew

Cut

HST 1 Unit

Press 8 ½ in x 8 ½ in (21.59 cm x 21.59 cm) Make 16

page 5

9.

Refer to Diagram I and Step 8 to make the following HST Units:

Dia. I HST 2 Unit

Use two Constellation and two Crescent Moon squares (5 in x 5 in / 12.7 cm x 12.7 cm) to make four HST 2 Units (4 ½ in x 4 ½ in / 11.43 cm x 11.43 cm).

4 ½ in x 4 ½ in (11.43 cm x 11.43 cm) Make 4 HST 2 Unit

Use two Floral Moon and two Zodiac squares (5 in x 5 in / 12.7 cm x 12.7 cm) to make four HST 3 Units (4 ½ in x 4 ½ in / 11.43 cm x 11.43 cm).

4 ½ in x 4 ½ in (11.43 cm x 11.43 cm) Make 4

10. Place one Floral Moon square and three Constellation squares (4 ½ in x 4 ½ in / 11.43 cm x 11.43 cm) in two rows as shown in Diagram J. Pin the pieces in each row RST, sew and press. Pin the rows RST matching seams, sew and press to make a Four-Patch 1 Unit (8 ½ in x 8 ½ in / 21.59 cm x 21.59 cm). Make eight.

Dia. J Row 1

Four-Patch 1 Unit

+ =

Row 2

+

=

+ 8 ½ in x 8 ½ in (21.59 cm x 21.59 cm) Make 8

11. Place one Constellation square, one Crescent Moon Square and two HST 2 Units (4 ½ in x 4 ½ in / 11.43 cm x 11.43 cm) in two rows as shown in Diagram K. Pin the pieces in each row RST, sew and press. Pin the rows RST matching seams, sew and press to make a Four-Patch 2 Unit (8 ½ in x 8 ½ in / 21.59 cm x 21.59 cm). Make two.

Dia. K Row 1

Four-Patch 2 Unit

+ =

Row 2

+

=

+ 8 ½ in x 8 ½ in (21.59 cm x 21.59 cm) Make 2

12. Refer to Diagram L and Step 11 using two Floral Moon squares, two Zodiac squares and four HST 3 Units (4 ½ in x 4 ½ in / 11.43 cm x 11.43 cm) to make two Four-Patch 3 Units (8 ½ in x 8 ½ in / 21.59 cm x 21.59 cm).

Dia. L Four-Patch 3 Unit

8 ½ in x 8 ½ in (21.59 cm x 21.59 cm) Make 2

13. Place one Celestial Square, one Four-Patch 1 Unit and two HST 1 Units (8 ½ in x 8 ½ in / 21.59 cm x 21.59 cm) in two rows as shown in Diagram M. Pin the pieces in each row RST, sew and press. Pin the rows RST matching seams, sew and press to make a Star Point Block (16 ½ in x 16 ½ in / 41.91 cm x 41.91 cm). Make eight.

Dia. M Star Point Block Row 1

+

=

Row 2

www.3wishesfabric.com

+

=

+ 16 ½ in x 16 ½ in (41.91 cm x 41.91 cm) Make 8

page 6

14. Refer to Diagram N and Step 13 using two Four-Patch 2 Units and six Crescent Moon squares (8 ½ in x 8 ½ in / 21.59 cm x 21.59 cm) to make two Center Block 1‘s (16 ½ in x 16 ½ in / 41.91 cm x 41.91 cm).

Dia. N

Center Block 1

16 ½ in x 16 ½ in (41.91 cm x 41.91 cm) Make 2

15. Refer to Diagram O and Step 13 using two Four-Patch 3 Units and six Zodiac squares (8 ½ in x 8 ½ in / 21.59 cm x 21.59 cm) to make two Center Block 2‘s (16 ½ in x 16 ½ in / 41.91 cm x 41.91 cm).

Dia. O

Center Block 2

16 ½ in x 16 ½ in (41.91 cm x 41.91 cm) Make 2

16. Use the templates provided to trace the appliqué shapes on the paper side of fusible web as shown in Diagram P. Leave ¼ in (6.35 mm) between shapes and cut out 1/8 in (3.18 mm) outside the traced line.

Dia. P

Full Moon Appliqué

Half Moon Appliqué

Waning Moon Appliqué

Crescent Moon Appliqué

Lightweight fusible web (17 in x 18 in / 43.18 cm x 45.72 cm) Cut 1 – Full Moon from Template Cut 1 – Waning Moon from Template Cut 1 – Half Moon from Template Cut 1 – Crescent Moon from Template

17. Refer to Diagram Q to place the fusible web appliqué pieces on the wrong side of the Ethereal fabric, adhesive side down. Fuse according to the manufacturer’s directions. Cut out on the traced lines; remove paper backing.

Dia. Q

Full Moon Appliqué

Crescent Moon Appliqué

Waning Moon Appliqué Half Moon Appliqué

Ethereal Cut 1 – Full Moon from Template Cut 1 – Waning Moon from Template Cut 1 – Half Moon from Template Cut 1 – Crescent Moon from Template

www.3wishesfabric.com

page 7

18. Refer to Diagram R to position the appliqué pieces on Center Blocks 1 and 2 (16 ½ in x 16 ½ in / 41.91 cm x 41.91 cm). Fuse to the right side of the fabric according to the manufacturer’s directions. Use a coordinating thread and small buttonhole or zig-zag stitch to secure and finish the edges. The Center Appliqué Blocks should measure 16 ½ in x 16 ½ in (41.91 cm x 41.91 cm) each.

Dia. R

Center Block 1 Full Moon Appliqué

Center Block 1 Waning Moon Appliqué

Center Block 2 Half Moon Appliqué

2 ¼ in (5.72 cm)

Center Block 2 Crescent Moon Appliqué

2 ¼ in (5.72 cm)

Buttonhole stitch Zigzag stitch

2 ¼ in (5.72 cm) 16 ½ in x 16 ½ in (41.91 cm x 41.91 cm)

16 ½ in x 16 ½ in (41.91 cm x 41.91 cm)

2 ¼ in (5.72 cm) 16 ½ in x 16 ½ in (41.91 cm x 41.91 cm)

16 ½ in x 16 ½ in (41.91 cm x 41.91 cm)

19. Place the Floral and Triangles Star Blocks and two Star Point Blocks (16 ½ in x 16 ½ in / 41.91 cm x 41.91 cm) as shown in Diagram S. Pin RST, sew and press to make Row 1 (16 ½ in x 64 ½ in / 41.91 cm x 163.83 cm).

Dia. S

Row 1

+

+

+

16 ½ in x 64 ½ in (41.91 cm x 163.83 cm)

20. Place the Center Block 1-Full Moon Appliqué, Center Block 2-Half Moon Appliqué and two Star Point Blocks (16 ½ in x 16 ½ in / 41.91 cm x 41.91 cm) as shown in Diagram T. Pin RST, sew and press to make Row 2 (16 ½ in x 64 ½ in / 41.91 m x 163.83 cm).

Dia. T

Row 2

+

+

+

16 ½ in x 64 ½ in (41.91 cm x 163.83 cm)

www.3wishesfabric.com

page 8

21. Place the Center Block 2-Crescent Moon Appliqué, Center Block 1-Waning Moon Appliqué and two Star Point Blocks (16 ½ in x 16 ½ in / 41.91 cm x 41.91 cm) as shown in Diagram U. Pin RST, sew and press to make Row 3 (16 ½ in x 64 ½ in / 41.91 cm x 163.83 cm).

Dia. U

Row 3

+

+

+

16 ½ in x 64 ½ in (41.91 cm x 163.83 cm)

22. Place Color Patch and Moon Phases Star Blocks and two Star Point Blocks (16 ½ in x 16 ½ in / 41.91 cm x 41.91 cm) as shown in Diagram V. Pin RST, sew and press to make Row 4 (16 ½ in x 64 ½ in / 41.91 cm x 163.83 cm).

Dia. V

Row 4

+

+

+

16 ½ in x 64 ½ in (41.91 cm x 163.83 cm)

www.3wishesfabric.com

page 9

23. Place Rows 1-4 as shown in Diagram W. Pin RST matching ends and seams. The finished Quilt Top should measure 64 ½ in x 64 ½ in (163.83 cm x 163.83 cm).

Dia. W

Moonlight Quilt Top

Row 1

+

Row 2

+

Row 3

+

Row 4

64 ½ in x 64 ½ in (163.83 cm x 163.83 cm)

www.3wishesfabric.com

page 10

Finishing

Dia. X

24. Remove the selvages from the Moon Phases Backing fabric. Note: Check orientation of design. Cut one piece 40 ¼ in x 72 in (102.24 cm x 182.88 cm) and two pieces 32 ¼ in x 36 ¼ in (81.92 cm x 92.08 cm). Pin RST and sew the two smaller pieces on the short edges; press. Pin the two sections RST along the long edges and sew as shown in Diagram X. Press the seam open or to one side. The Backing should measure 72 in x 72 in (182.88 cm x 182.88 cm).

25. Press finished Quilt Top and Backing. Tape the Backing, wrong side up, to a firm surface. Layer Batting and Quilt Top (right side up). Baste the layers together with safety pins. Quilt as desired.

26. Once quilting is complete, square up corners and edges, trimming excess Backing and Batting even with the Quilt Top.

32 ¼ in x 36 ¼ in (81.92 cm x 92.08 cm)

40 ¼ in x 72 in (102.24 cm x 182.88 cm)

32 ¼ in x 36 ¼ in (81.92 cm x 92.08 cm)

Backing 72 in x 72 in (182.88 cm x 182.88 cm)

27. Binding – Follow Diagram Y to make the Ethereal Binding. Remove selvages and sew the short ends of the seven 2 ½ in (6.35 cm) x wof strips RST end to end at a 45° angle to make one continuous strip; press seams open. Press one short end ¼ in (6.35 mm) to the wrong side. Fold in half lengthwise with wrong sides together; press. Leaving a 2 in (5.08 cm) tail on the folded end, place cut edges of folded Binding even with the edge of the Quilt Top and sew, mitering the corners. Overlap ends, trim any excess and finish sewing the Binding. Fold Binding over to back and hand stitch.

Dia. Y

Stop stitching ¼ in (6.35 mm) from end of quilt

Finished Care Instructions Machine wash in cold water; gentle cycle. Do not bleach. Tip: Before drying, check for fabric dyes that may have run. If fabric dyes run, rewash and rinse using a color catcher to absorb loose dye. Lay flat to dry or tumble dry low.

www.3wishesfabric.com

©2022 3 Wishes Fabric®

page 11

Appliqué Template (100% Scale) Trace on paper side of fusible web.

Scale: 1 square = 1 in x 1 in

Full Moon Template Cut 1 – Ethereal

Appliqué Template (100% Scale) Trace on paper side of fusible web.

Half Moon Template Cut 1 – Ethereal

Scale: 1 square = 1 in x 1 in

Appliqué Template (100% Scale) Trace on paper side of fusible web.

Scale: 1 square = 1 in x 1 in

Crescent Moon Template Cut 1 – Ethereal

Appliqué Template (100% Scale) Trace on paper side of fusible web.

Scale: 1 square = 1 in x 1 in

Waning Moon Template Cut 1 – Ethereal

www.3wishesfabric.com

Follow us here to see more exciting projects and ideas!

Quilt

Featuring the Seas the Day Collection

by Beth Albert and the Good Vibes Collection

by Courtney Morgenstern Shipping to stores January 2022

Finished Size: 42 ½ in x 42 ½ in (107.95 cm x 107.95 cm)

Fabric Needed 3 Wishes Fabric® Seas the Day Collection • 1 Panel – Sea Panel (18725-PNL-CTN-D) • 1 3⁄8 yds – Sky (18723-PNK-CTN-D) • 1 3⁄8 yds – Words (18726-NVY-CTN-D) for Piecing and Binding • 7⁄8 yd – Waves (18722-BLU-CTN-D) • ⁵⁄8 yd – Palms (18724-GRN-CTN-D) • 4 ¼ yds – Turtles (18721-GRN-CTN-D) for Backing

Additional Supplies Needed: • 72 in x 72 in (182.88 cm x 182.88 cm) Cotton batting • Piecing and sewing thread • Quilting and sewing supplies • Even-feed foot (optional for quilting)

3 Wishes Fabric® Good Vibes Collection • 1 1⁄8 yds – Circle Dots (18660-WOW-CTN-D)

page 1

Before You Begin Read all instructions before beginning project. Do not pre-wash fabrics. Press fabrics with a dry iron on cotton setting before cutting. Use a ¼ in (6.35 mm) seam allowance and sew fabrics with right sides together (RST) unless otherwise noted. Press seams in the direction of the arrows. wof = width of fabric

Cutting Use a rotary cutter and ruler to cut the size and number of squares and rectangles from each fabric listed below.

8 ½ in x 8 ½ in

16 ½ in x 16 ½ in

Sea Panel (18725-PNL-CTN-D) 1 Panel Fussy Cut 1 - 16 ½ in x 16 ½ in (41.91 cm x 41.91 cm) Fussy Cut 8 - 8 ½ in x 8 ½ in (21.59 cm x 21.59 cm) 2 1⁄2 in x wof 9 in x 9 in

8 ½ in x 8 ½ in

9 in x 9 in

8 ½ in x 16 ½ in

Sky (18723-PNK-CTN-D) 1 3⁄8 yards Cut 4 - 9 in x 9 in (22.86 cm x 22.86 cm) Cut 16 - 8 ½ in x 8 ½ in (21.59 cm x 21.59 cm)

www.3wishesfabric.com

Words (18726-NVY-CTN-D) 1 3⁄8 yards Cut 7 - 2 1⁄2 in (6.35 cm) x wof Cut 4 - 9 in x 9 in (22.86 cm x 22.86 cm) Cut 4 - 8 ½ in x 16 ½ in (21.59 cm x 41.91 cm)

page 2

9 in x 9 in

9 in x 9 in

8 ½ in x 8 ½ in

4 ½ in x 8 ½ in

8 ½ in x 16 ½ in

Waves (18722-BLU-CTN-D) 7⁄8 yard Cut 4 - 9 in x 9 in (22.86 cm x 22.86 cm) Cut 4 - 8 ½ in x 16 ½ in (21.59 cm x 41.91 cm)

8 ½ in x 8 ½ in

Circle Dots (18660-WOW-CTN-D) 1 1⁄8 yards Cut 4 - 9 in x 9 in (22.86 cm x 22.86 cm) Cut 8 - 8 ½ in x 8 ½ in (21.59 cm x 21.59 cm) Cut 8 - 4 ½ in x 8 ½ in (11.43 cm x 21.59 cm)

Palms (18724-GRN-CTN-D) 5⁄8 yard Cut 8 - 8 ½ in x 8 ½ in (21.59 cm x 21.59 cm)

Sewing

Note: Check orientation of the design so it will be correct when placing each unit in the quilt.

1. Draw a diagonal line on the wrong side of a Circle Dots square 9 in x 9 in (22.86 cm x 22.86 cm) as shown in Diagram A. Place on top of a Words square 9 in x 9 in (22.86 cm x 22.86 cm) RST and sew ¼ in (6.35mm) away from the line on both sides.

1⁄4 in (6.35 mm) Dia. A +

=

Draw Wrong side

Sew

2. Cut on the drawn line; press; trim if necessary. Note: Two squares yield two Half-Square Triangle Units. Repeat to make a total of two Words/Circle Dots HST Unit A1s and two Words/Circle Dots HST Unit A2s 8 ½ in x 8 ½ in (21.59 cm x 21.59 cm). Tip: Check fabric orientation before cutting. Label Units.

Dia. B

Cut

www.3wishesfabric.com

Words/Circle Dots HST Unit A1

Words/Circle Dots HST Unit A2

Press Make 2

Press Make 2

Square up to 8 ½ in x 8 ½ in (21.59 cm x 21.59 cm)

page 3

3. Follow Steps 1 and 2 and Diagram C using two Circle Dots squares 9 in x 9 in (22.86 cm x 22.86 cm) and two Words squares 9 in x 9 in (22.86 cm x 22.86 cm) to make two Words/Circle Dots HST Unit B1s and two Words/Circle Dots HST Unit B2s 8 ½ in x 8 ½ in (21.59 cm x 21.59 cm).

1⁄4 in (6.35 mm)

Dia. C

+

Words/Circle Dots HST Unit B1

Words/Circle Dots HST Unit B2

Press Make 2 8 ½ in x 8 ½ in (21.59 cm x 21.59 cm)

Press Make 2 8 ½ in x 8 ½ in (21.59 cm x 21.59 cm)

=

Draw Wrong side

Sew

Cut

4. Follow Steps 1 and 2 and Diagram D using two Waves squares 9 in x 9 in (22.86 cm x 22.86 cm) and two Sky squares 9 in x 9 in (22.86 cm x 22.86 cm) to make two Sky/Waves HST Unit A-1s and two Sky/Waves HST Unit A-2s 8 ½ in x 8 ½ in (21.59 cm x 21.59 cm).

Dia. D 1⁄4 in (6.35 mm)

+

Sky/Waves HST Unit A1

Sky/Waves HST Unit A2

Press Make 2 8 ½ in x 8 ½ in (21.59 cm x 21.59 cm)

Press Make 2 8 ½ in x 8 ½ in (21.59 cm x 21.59 cm)

=

Draw Wrong side

Sew

Cut

5. Follow Steps 1 and 2 and Diagram E using two Waves squares 9 in x 9 in (22.86 cm x 22.86 cm) and two Sky squares 9 in x 9 in (22.86 cm x 22.86 cm) to make two Sky/Waves HST Unit B1s and two Sky/Waves HST Unit B2s 8 ½ in x 8 ½ in (21.59 cm x 21.59 cm).

1⁄4 in (6.35 mm)

Dia. E

+

Draw Wrong side

www.3wishesfabric.com

Sky/Waves HST Unit B1

Sky/Waves HST Unit B2

Press Make 2 8 ½ in x 8 ½ in (21.59 cm x 21.59 cm)

Press Make 2 8 ½ in x 8 ½ in (21.59 cm x 21.59 cm)

=

Sew

Cut

page 4

6. Refer to Diagram F to make Flying Geese Units. Draw a diagonal line on the wrong side of a Sky square 8 ½ in x 8 ½ in (21.59 cm x 21.59 cm) oriented as shown. Place RST on the left side of a Words rectangle 8 ½ in x 16 ½ in (21.59 cm x 41.91 cm) oriented as shown. Sew on the diagonal line. Trim seam to ¼ in (6.35mm); press open. Repeat with a second Sky square 8 ½ in x 8 ½ in (21.59 cm x 21.59 cm) on the right side of the rectangle to make a Sky/Words FG Unit 1 finishing at 8 ½ in x 16 ½ in (21.59 cm x 41.91 cm). Make three. Repeat, reversing the orientation of the Words rectangle to make one Sky/Words FG Unit 2.

Tip: Check fabric orientation before cutting.

Dia. F

Draw Wrong side

1⁄4 in (6.35 mm)

Sew

Cut

Press

1⁄4 in (6.35 mm)

Draw Wrong side

Sew

Cut

Sky/Words FG Unit 1

Sky/Words FG Unit 2

Press Make 3 8 ½ in x 16 ½ in (21.59 cm x 41.91 cm)

Make 1 8 ½ in x 16 ½ in (21.59 cm x 41.91 cm)

7. Refer to Diagram G and Step 6 using eight Sky squares 8 ½ in x 8 ½ in (21.59 cm x 21.59 cm) and four Waves rectangles 8 ½ in x 16 ½ in (21.59 cm x 41.91 cm) to make four Sky/Waves FG Units 8 ½ in x 16 ½ in (21.59 cm x 41.91 cm).

Sky/Waves FG Unit 1

Sky/Waves FG Unit 2

Make 1 8 ½ in x 16 ½ in (21.59 cm x 41.91 cm)

Make 3 8 ½ in x 16 ½ in (21.59 cm x 41.91 cm)

Dia. G

8. Place a Circle Dots rectangle 4 ½ in x 8 ½ in (11.43 cm x 21.59 cm) on the top and bottom of the Sea Panel Fussy Cut Star Fish square 8 ½ in x 8 ½ in (21.59 cm x 21.59 cm) as shown in Diagram H. Pin RST, sew and press to make the Star Fish Block 8 ½ in x 16 ½ in (21.59 cm x 41.91 cm).

Dia. H

Star Fish Block

+

=

+

8 ½ in x 16 ½ in (21.59 cm x 41.91 cm)

www.3wishesfabric.com

page 5

9. Place a Circle Dots rectangle 4 ½ in x 8 ½ in (11.43 cm x 21.59 cm) on the top and bottom of the Sea Panel Fussy Cut Beach square 8 ½ in x 8 ½ in (21.59 cm x 21.59 cm) as shown in Diagram I. Pin RST, sew and press to make the Beach Block 8 ½ in x 16 ½ in (21.59 cm x 41.91 cm).

Dia. I

Beach Block

+

=

+

8 ½ in x 16 ½ in (21.59 cm x 41.91 cm)

10. Place two Circle Dots squares, one Circle Dots/Words HST Unit A1, one Circle Dots/Words HST Unit B1, two Palms squares 8 ½ in x 8 ½ in (21.59 cm x 21.59 cm) and one Sky/Words FG Unit 1 8 ½ in x 16 ½ in (21.59 cm x 41.91 cm) oriented as shown in Diagram J. Pin RST, sew and press to make Row 1 finishing at 8 ½ in x 64 ½ in (21.59 cm x 163.83 cm).

Dia. J

+

+

+

+

+

+

Row 1

8 ½ in x 64 ½ in (21.59 cm x 163.83 cm)

11. Follow Step 10 and Diagram K using one Circle Dots/Words HST Unit A2, one Circle Dots/Words HST Unit B2, two Circle Dots squares, one Sky/Waves HST Unit A2, one Sky/Waves HST Unit B2 8 ½ in x 8 ½ in (21.59 cm x 21.59 cm) and one Sky/Waves FG Unit 2 8 ½ in x 16 ½ in (21.59 cm x 41.91 cm) oriented as shown to make Row 2 finishing at 8 ½ in x 64 ½ in (21.59 cm x 163.83 cm).

Dia. K

Row 2

8 ½ in x 64 ½ in (21.59 cm x 163.83 cm)

12. Follow Step 10 and Diagram L using two Palms squares, one Sky/Waves HST Unit B2, one Sky/Waves HST Unit A2, three Sea Panel Fussy Cut squares 8 ½ in x 8 ½ in (21.59 cm x 21.59 cm) and two Circle Dots rectangles 4 ½ in x 8 ½ in (11.43 cm x 21.59 cm) oriented as shown to make Row 3 finishing at 8 ½ in x 64 ½ in (21.59 cm x 163.83 cm).

Dia. L

Row 3

8 ½ in x 64 ½ in (21.59 cm x 163.83 cm)

www.3wishesfabric.com

page 6

13. Follow Step 10 and Diagram M using two Sky/Words FG Unit 1's, two Sky/Waves FG Unit 2's 8 ½ in x 16 ½ in (21.59 cm x 41.91 cm), the Star Fish and Beach Blocks 4 ½ in x 16 ½ in (11.43 cm x 41.91 cm) and the Sea Panel Fussy Cut Sun Square 16 ½ in x 16 ½ in (41.91 cm x 41.91 cm) oriented as shown to make Row 4 finishing at 16 ½ in x 64 ½ in (41.91 cm x 163.83 cm).

Dia. M

Row 4

16 ½ in x 64 ½ in (41.91 cm x 163.83 cm)

14. Follow Step 10 and Diagram N using two Palms squares, one Sky/Waves HST Unit A1, one Sky/Waves HST Unit B1, three Sea Panel Fussy Cut squares 8 ½ in x 8 ½ in (21.59 cm x 21.59 cm) and two Circle Dots rectangles 4 ½ in x 8 ½ in (11.43 cm x 21.59 cm) oriented as shown to make Row 5 finishing at 8 ½ in x 64 ½ in (21.59 cm x 163.83 cm).

Dia. N

Row 5

8 ½ in x 64 ½ in (21.59 cm x 163.83 cm)

15. Follow Step 10 and Diagram O using one Circle Dots/Words HST Unit B1, one Circle Dots/Words HST Unit A1, two Circle Dots squares, one Sky/Waves HST Unit B1, one Sky/Waves HST Unit A2 8 ½ in x 8 ½ in (21.59 cm x 21.59 cm) and one Sky/Waves FG Unit 1 8 ½ in x 16 ½ in (21.59 cm x 41.91 cm) oriented as shown to make Row 6 finishing at 8 ½ in x 64 ½ in (21.59 cm x 163.83 cm).

Dia. O

Row 6

8 ½ in x 64 ½ in (21.59 cm x 163.83 cm)

16. Follow Step 10 and Diagram P using two Circle Dots squares, one Circle Dots/Words HST Unit B2, one Circle Dots/Words HST Unit A2, two Palms squares 8 ½ in x 8 ½ in (21.59 cm x 21.59 cm) and one Sky/Words FG Unit 2 8 ½ in x 16 ½ in (21.59 cm x 41.91 cm) oriented as shown to make Row 7 finishing at 8 ½ in x 64 ½ in (21.59 cm x 163.83 cm).

Dia. P

Row 7

8 ½ in x 64 ½ in (21.59 cm x 163.83 cm)

www.3wishesfabric.com

page 7

17. Place Rows 1-7 oriented as shown in Diagram Q. Pin RST matching ends and seams, sew and press. The finished Quilt Top should measure 64 ½ in x 64 ½ in (163.83 cm x 163.83 cm).

Dia. Q

Seas the Day Quilt Top

Row 1

+ Row 2

+ Row 3

+

Row 4

+

Row 5

+ Row 6

+ Row 7

64 ½ in x 64 ½ in (163.83 cm x 163.83 cm)

www.3wishesfabric.com

page 8

Finishing 18. Remove the selvages from the Turtles Backing fabric. Cut one piece 40 ¼ in x 72 in (102.24 cm x 182.88 cm) and two pieces 32 ¼ in x 36 ¼ in (81.92 cm x 92.08 cm). Pin the two smaller pieces RST on the short edges and sew as shown in Diagram U; press.

Pin the two sections RST along the long edges, sew and press open or to one side. Note: Check orientation of the design. The Backing should measure 72 in x 72 in (182.88 cm x 182.88 cm).

Backing

32 ¼ in x 36 ¼ in

40 ¼ in x 72 in

32 ¼ in x 36 ¼ in

72 in x 72 in (182.88 cm x 182.88 cm)

19. Press finished Quilt Top and Backing. Tape the Backing, wrong side up, to a firm surface. Layer Batting and Quilt Top (right side up). Baste the layers together with safety pins. Quilt as desired.

20. Once quilting is complete, square up corners and edges, trimming excess Backing and Batting even with the Quilt Top. 21. Follow Diagram R to make the Words Binding. Remove selvages and sew the short ends of the seven 2 ½ in (6.35 cm) x wof strips RST end to end at a 45° angle to make one continuous strip; press seams open. Press one short end ¼ in (6.35 mm) to the wrong side. Fold in half lengthwise with wrong sides together; press. Leaving a 2 in (5.08 cm) tail on the folded end, place cut edges of folded Binding even with the edge of the Quilt Top and sew, mitering the corners. Overlap ends, trim any excess and finish sewing the Binding. Fold Binding over to back and hand stitch.

Dia. R

Finished Care Instructions Machine wash in cold water; gentle cycle. Do not bleach. Tip: Before drying, check for fabric dyes that may have run. If fabric dyes run, rewash and rinse using a color catcher to absorb loose dye. Lay flat to dry or tumble dry low.

www.3wishesfabric.com

©2022 3 Wishes Fabric®

page 9

www.3wishesfabric.com

Follow us here to see more exciting projects and ideas!

Quilt Featuring the Steam in the Spring collection

by Michael Shelton Shipping to stores January 2022

Finished Size: 64 ½ in x 58 ½ in (163.83 cm x 148.59 cm)

Fabric Needed 3 Wishes Fabric® Steam in the Spring Collection • 1 Panel – Lg. Train Panel (18714-PNL-CTN-D) • 1 1/2 yds – Scenic (18718-MLT-CTN-D) • 1 yd – Map (18717-BLU-CTN-D) for Piecing and Binding • 1 yd – Trains (18720-MLT-CTN-D) • 1/4 yd – Foliage (18715-GRN-CTN-D • 1/4 yd – Signs (18716-GRY-CTN-D) • 3 3/4 yds – Foliage (18715-GRN-CTN-D) for Backing

Additional Supplies Needed: • 72 in x 66 in (182.88 cm x 167.64 cm) Cotton batting • Piecing and sewing thread • Quilting and sewing supplies • Even-feed foot (optional for quilting)

3 Wishes Fabric® Good Vibes Collection • 1/4 yd – Circle Dots (18660-WOW-CTN-D)

page 1

Before You Begin Read all instructions before beginning project. Do not pre-wash fabrics. Press fabrics with a dry iron on cotton setting before cutting.

Use a ¼ in (6.35 mm) seam allowance and sew fabrics with right sides together (RST) unless otherwise noted. Press seams in the direction of the arrows. wof = width of fabric. Print appliqué template page at 100% scale. Note: A printed panel may become slightly skewed during the finishing process. Check if panel is square before cutting by folding the panel so selvages meet. If all edges do not meet, pull firmly from corner to corner until the edges meet. Continue until all corners are square.

Cutting

Use a rotary cutter and ruler to cut the size and number of squares and rectangles from each fabric listed below.

2 ½ in x wof 2 ½ in x wof 2 ½ in x wof 2 ½ in x wof 2 ½ in x wof 2 ½ in x wof 2 ½ in x wof 32 ½ in x 38 ½ in

4 ½ in x 6 ½ in

4 ½ in x 8 ½ in 4 ½ in x 6 ½ in

4 ½ in x 8 ½ in 4 ½ in x 6 ½ in

4 ½ in x 8 ½ in

4 ½ in x 6 ½ in

4 ½ in x 8 ½ in

4 ½ in x 6 ½ in

4 ½ in x 8 ½ in

4 ½ in x 6 ½ in

4 ½ in x 8 ½ in

4 ½ in x 6 ½ in

4 ½ in x 8 ½ in

4 ½ in x 6 ½ in

4 ½ in x 8 ½ in

Lg. Train Panel – 18714-PNL-CTN-D (1 yd x wof / 91.44 cm x 106.68 cm) Fussy Cut 1 – 32 ½ in x 38 ½ in (82.55 cm x 97.79 cm) 4 ½ in x 34 ½ in

Map – 18717-BLU-CTN-D (1 1/8 yd x wof / 91.44 cm x 106.68 cm) Cut 7 – 2 ½ in x wof (6.35 cm x 106.68 cm) Cut 8 – 2 ½ in x 8 ½ in (6.35 cm x 21.59 cm) Cut 8 – 2 ½ in x 6 ½ in (6.35 cm x 16.51 cm)

4 ½ in x 34 ½ in 4 ½ in x 26 ½ in

3 ½ in x 29 ½ in 3 ½ in x 29 ½ in

4 ½ in x 26 ½ in 3 ½ in x 29 ½ in 3 ½ in x 29 ½ in 3 ½ in x 29 ½ in

4 ½ in x 24 ½ in

3 ½ in x 29 ½ in 4 ½ in x 24 ½ in

4 ½ in x 32 ½ in

4 ½ in x 32 ½ in

3 ½ in x 29 ½ in

3 ½ in x 29 ½ in

Trains – 18720-BLU-CTN-D (1 1/8 yd x wof / 91.44 cm x 106.68 cm) Fussy Cut 8 – 3 ½ in x 29 ½ in (8.89 cm x 74.93 cm)

Scenic – 18718-MLT-CTN-D (1 ½ yd x wof / 137.16 cm x 106.68 cm) Cut 2 – 4 ½ in x 34 ½ in (11.43 cm x 87.63 cm) Cut 2 – 4 ½ in x 26 ½ in (11.43 cm x 67.31 cm) Cut 2 – 4 ½ in x 32 ½ in (11.43 cm x 82.55 cm) Cut 2 – 4 ½ in x 24 ½ in (11.43 cm x 62.23 cm) Note: Orient rectangles as shown

www.3wishesfabric.com

page 2

1 ½ in x 40 ½ in 1 ½ in x 40 ½ in 1 ½ in x 36 ½ in 1 ½ in x 36 ½ in

4 ½ in x 4 ½ in

Foilage – 18715-GRN-CTN-D (1/4 yd x wof / 22.86 cm x 106.68 cm) Cut 2 – 1 ½ in x 40 ½ (6.35 cm x 102.87 cm) Cut 2 – 1 ½ in x 36 ½ in (6.35 cm x 92.71 cm)

4 ½ in x 4 ½ in

4 ½ in 4 ½ in x x 4 ½ in 4 ½ in

4 ½ in x 4 ½ in

4 ½ in x 4 ½ in

4 ½ in x 4 ½ in

4 ½ in x 4 ½ in

Signs – 18716-GRY-CTN-D (1/4 yd x wof / 22.86 cm x 106.68 cm) Cut 8 – 4 ½ in x 4 ½ (11.43 cm x 11.43 cm)

1 ½ in x 38 ½ in 1 ½ in x 38 ½ in 1 ½ in x 34 ½ in 1 ½ in x 34 ½ in

Circle Dots – 18660-WOW-CTN-D (1/4 yd x wof / 22.86 cm x 106.68 cm) Cut 2 – 1 ½ in x 38 ½ (6.35 cm x 97.79 cm) Cut 2 – 1 ½ in x 34 ½ in (6.35 cm x 87.63 cm)

Sewing 1.

Refer to Diagram A to make the Center Unit.

Place a Circle Dots strip (1 ½" x 38 ½" / 3.81 cm x 97.79 cm) on top and bottom of the Fussy Cut Lg. Train Panel rectangle (32 ½" x 38 ½ / 82.55 cm x 97.79 cm). Pin RST matching ends and centers, sew and press.

Place a Circle Dots strip (1 ½" x 34 ½" / 3.81 cm x 87.63 cm) on each side. Pin RST matching ends and centers, sew and press.

Place a Foliage strip (1 ½" x 40 ½" / 3.81 cm x 102.87 cm) on the top and bottom. Pin RST matching ends and centers, sew and press.

Place a Foliage strip (1 ½" x 36 ½" / 3.81 cm x 92.71 cm) on each side. Pin RST matching ends and centers, sew and press.

The Center Unit should measure 42 ½" x 36 ½" (107.95 cm x 92.71 cm).

Dia. A Center Unit +

+

+

+

+

+

+ + 42 ½ in x 36 ½ in (107.95 cm x 92.71 cm)

www.3wishesfabric.com

page 3

2.

Place a horizontal Map rectangle (4 ½" x 8 ½" / 11.43 cm x 21.59 cm) on each side of a horizontal Scenic rectangle (4 ½" x 26 ½" / 11.43 cm x 67.31 cm) as shown in Diagram B. Note: Check orientation of designs. Pin RST, sew and press to make the Border 1 Top (4 ½" x 42 ½" / 11.43 cm x 107.95 cm). Repeat to make the Border 1 Bottom.

Dia. B

Border 1 Top and Bottom +

+

=

4 ½ in x 42 ½ in (11.43 cm x 107.95 cm) Make 2

3.

Place two Signs squares (4 ½" x 4 ½" / 11.43 cm x 11.43 cm), two vertical Map rectangles (4 ½" x 6 ½" / 11.43 cm x 16.51 cm) and one vertical Scenic rectangle (4 ½" x 24 ½" / 11.43 cm x 62.23cm) as shown in Diagram C. Note: Check orientation of designs. Pin RST, sew and press to make the Border 1 Sides (4 ½" x 44 ½" / 11.43 cm x 113.03 cm). Make two.

Dia. C

Border 1 Sides +

+

+

+

=

4 ½ in x 44 ½ in (11.43 cm x 113.03 cm) Make 2

4.

Place a horizontal Map rectangle (4 ½" x 8 ½" / 11.43 cm x 21.59 cm) on each side of a horizontal Scenic rectangle (4 ½" x 34 ½" / 11.43 cm x 87.63 cm) as shown in Diagram D. Note: Check orientation of designs. Pin RST, sew and press to make the Border 2 Top (4 ½" x 50 ½" / 11.43 cm x 128.27 cm). Repeat to make the Border 2 Bottom.

Dia. D

Border 2 Top and Bottom +

+

=

4 ½ in x 50 ½ in (11.43 cm x 128.27 cm) Make 2

5.

Place two Signs squares (4 ½" x 4 ½" / 11.43 cm x 11.43 cm), two vertical Map rectangles (4 ½" x 6 ½" / 11.43 cm x 16.51 cm) and one vertical Scenic rectangle (4 ½" x 32 ½" / 11.43 cm x 82.55 cm) as shown in Diagram E. Note: Check orientation of designs. Pin RST, sew and press to make the Border 2 Sides (4 ½" x 52 ½" / 11.43 cm x 133.35 cm). Make two.

Dia. E

Border 2 Sides +

+

+

+

=

4 ½ in x 52 ½ in (11.43 cm x 133.35 cm) Make 2

www.3wishesfabric.com

page 4

6.

Place the two Fussy Cut Trains rectangles (3 ½" x 29 ½" / 8.89 cm x 74.93 cm) as shown in Diagram F, aligning the trains at the seam.

Note: Check orientation of designs. Pin RST, sew and press open or to one side to make Border 3 (3 ½" x 58 ½" / 8.89 cm x 148.59 cm). Make four.

Dia. F

Border 3 +

=

3 ½ in x 58 ½ in (8.89 cm x 148.59 cm) Make 4

7.

Refer to Diagram G to place the Borders around the Center Unit (42 ½" x 36 ½" / 107.95 cm x 92.71 cm). Sew each Border RST in the order listed. Note: Check orientation of the design. Pin matching center and ends. Press seams as shown. Measure at each step to ensure the next border will fit. If one border is a little larger than the border it is being sewn to, pin well to ease the fullness and place the fullness on the bottom while sewing.

Border 2 Border 2 Top and Bottom: (4 ½" x 50 ½" / 11.43 cm x 128.27 cm) Border 2 Sides: (4 ½" x 52 ½" / 11.43 cm x 133.35 cm) Quilt Top 58 ½" x 52 ½" (128.27 cm x 133.35 cm).

Border 1 Border 1 Top and Bottom: (4 ½" x 42 ½" / 11.43 cm x 107.95 cm) Border 1 Sides: (4 ½" x 44 ½" / 11.43 cm x 113.03 cm) Quilt Top 50 ½" x 44 ½" (128.27 cm x 113.03 cm).

Border 3 Border 3 Top and Bottom: (3 ½" x 58 ½" / 8.89 cm x 148.59 cm) Border 3 Sides: (3 ½" x 58 ½" / 8.89 cm x 148.59 cm) Quilt Top 64 ½" x 58 ½" (163.83 cm x 148.59 cm).

Dia. G

Steam in the Spring Quilt Top Border 3 +

Border 2 +

Border 1 +

+

+

+

+

+

+

+

+

+

64 ½ in x 58 ½ in (163.83 cm x 148.59 cm)

www.3wishesfabric.com

page 5

Finishing

Dia. H

8.

Remove the selvages from the Foliage Backing fabric. Cut two pieces 36 ¼” x 66” (92.075 cm x 167.64 cm). Pin the two sections RST along the long edges as shown in Diagram H and sew. Note: Check orientation of the design. Press seams open or to one side. The Backing should measure 72" x 66" (182.88 cm x 167.64 cm).

9.

Press finished Quilt Top and Backing. Tape the Backing, wrong side up, to a firm surface. Layer Batting and Quilt Top (right side up). Baste the layers together with safety pins. Quilt as desired.

36 ¼ in x 66 in

36 ¼ in x 66 in

10. Once quilting is complete, square up corners and edges, trimming excess Backing and Batting even with the Quilt Top. 11. Binding – Follow Diagram I to make the Map Binding.

Remove selvages and sew the short ends of the seven 72 in x 66 in (182.88 cm x 167.64 cm) 2 ½" x wof (6.35 cm x wof) strips RST end to end at a 45˚ angle to make one continuous strip; press seams open.

Press one short end ¼" (6.35 mm) to the wrong side. Fold in half lengthwise with wrong sides together; press. Leaving a 2" (5.08 cm) tail on the folded end, place cut edges of folded Binding even with the edge of the Quilt Top and sew, mitering the corners.

Overlap ends, trim any excess and finish sewing the Binding. Fold Binding over to back and hand stitch.

Dia. I

Stop stitching ¼ in (6.35 mm) from end of quilt

Finished Care Instructions Machine wash in cold water; gentle cycle. Do not bleach. Tip: Before drying, check for fabric dyes that may have run. If fabric dyes run, rewash and rinse using a color catcher to absorb loose dye. Lay flat to dry or tumble dry low.

www.3wishesfabric.com

page 6

www.3wishesfabric.com

Follow us here to see more exciting projects and ideas!

Wall Hanging Featuring the Steam in the Spring Collection

by Michael Shelton and the Good Vibes Collection

by Courtney Morgenstern Shipping to stores January 2022

Finished Size: 42 ½ in x 42 ½ in (107.95 cm x 107.95 cm)

Fabric Needed 3 Wishes Fabric ® Steam in the Spring Collection • 1 Panel – Train 4-Panel (18719-PNL-CTN-D) • 1 3⁄8 yards – Scenic (18718-MLT-CTN-D) • 5⁄8 yard – Map (18717-BLU-CTN-D) for Piecing and Binding • 1⁄4 yard – Foliage (18715-GRN-CTN-D) • 1⁄4 yard – Signs (18716-GRY-CTN-D) • 1⁄4 yard – Trains (18720-MLT-CTN-D) • 2 1⁄4 yards – Scenic (18718-MLT-CTN-D) Backing

Additional Supplies Needed: • 51 in x 51 in (129.54 cm x 129.54 cm) Cotton batting • Piecing and sewing thread • Quilting and sewing supplies • Even-feed foot (optional for quilting)

3 Wishes Fabric ® Good Vibes Collection • 1⁄4 yard – Circle Dots (18660-WOW-CTN-D)

page 1

Before You Begin Read all instructions before beginning project. Do not pre-wash fabrics. Press fabrics with a dry iron on cotton setting before cutting.

Use a ¼ in (6.35 mm) seam allowance and sew fabrics with right sides together (RST) unless otherwise noted. Press seams in the direction of the arrows. wof = width of fabric Note: A printed panel may become slightly skewed during the finishing process. Check if panel is square before cutting by folding the panel so selvages meet. If all edges do not meet, pull firmly from corner to corner until the edges meet. Continue until all corners are square.

Cutting Use a rotary cutter and ruler to cut the size and number of squares and rectangles from each fabric listed below.

2 1⁄2 in x wof 12 1⁄2 in x 12 1⁄2 in

12 1⁄2 in x 12 1⁄2 in

2 1⁄2 in x 16 1⁄2 in

2 1⁄2 in x 12 1⁄2 in

12 1⁄2 in x 12 1⁄2 in

12 1⁄2 in x 12 1⁄2 in

Map (18717-BLU-CTN-D) 5⁄8 yard Cut 5 - 2 1⁄2 in (6.35 cm) x wof Cut 2 - 2 1⁄2 in x 16 1⁄2 in (6.35 cm x 41.91 cm) Cut 2 - 2 1⁄2 in x 12 1⁄2 in (6.35 cm x 31.75 cm) 2 1⁄2 in x 16 1⁄2 in

2 1⁄2 in x 12 1⁄2 in

Train 4-Panel (18719-PNL-CTN-D) 1 Panel Fussy Cut 4 - 12 1⁄2 in x 12 1⁄2 in (31.75 cm x 31.75 cm)

4 1⁄2 in x 42 1⁄2 in

Foliage (18715-GRN-CTN-D) 1⁄4 yard Cut 2 - 2 1⁄2 in x 16 1⁄2 in (6.35 cm x 41.91 cm) Cut 2 - 2 1⁄2 in x 12 1⁄2 in (6.35 cm x 31.75 cm) 2 1⁄2 in x 16 1⁄2 in

2 1⁄2 in x 12 1⁄2 in

4 1⁄2 in x 34 1⁄2 in

Signs (18716-GRY-CTN-D) 1⁄4 yard Cut 2 - 2 1⁄2 in x 16 1⁄2 in (6.35 cm x 41.91 cm) Cut 2 - 2 1⁄2 in x 12 1⁄2 in (6.35 cm x 31.75 cm) 2 1⁄2 in x 16 1⁄2 in

2 1⁄2 in x 12 1⁄2 in

Trains (18720-MLT-CTN-D) 1⁄4 yard Cut 2 - 2 1⁄2 in x 16 1⁄2 in (6.35 cm x 41.91 cm) Cut 2 - 2 1⁄2 in x 12 1⁄2 in (6.35 cm x 31.75 cm) 1 1⁄2 in x 34 1⁄2 in 1 1⁄2 in x 32 1⁄2 in

Scenic (18718-MLT-CTN-D) 1 3⁄8 yards Cut 2 - 4 1⁄2 in x 42 1⁄2 in (11.43 cm x 107.95 cm) Cut 2 - 4 1⁄2 in x 34 1⁄2 in (11.43 cm x 87.63 cm)

www.3wishesfabric.com

Circle Dots (18660-WOW-CTN-D) 1⁄4 yard Cut 2 - 1 1⁄2 in x 34 1⁄2 in (3.81 cm x 87.63 cm) Cut 2 - 1 1⁄2 in x 32 1⁄2 in (3.81 cm x 82.55 cm)

page 2

Sewing 1. Place a Foliage rectangle 2 ½ in x 12 ½ in (6.35 cm x 31.75 cm) on each side of the Fussy Cut Train 4-Panel square 12 ½ in x 12 ½ in (31.75 cm x 31.75 cm) as shown in Diagram A. Pin RST, sew and press. Place a Foliage rectangle 2 ½ in x 16 ½ in (6.35 cm x 41.91cm) on the top and bottom. Pin RST, sew and press to make the Panel 1 Unit 16 ½ in x 16 ½ in (41.91cm x 41.91 cm).

Dia. A

Panel 1 Unit +

+

+

=

+ 16 1⁄2 in x 16 1⁄2 in (41.91 cm x 41.91 cm)

2. Refer to Diagram B and Step 1 to make the Panel 2 Unit 16 ½ in x 16 ½ in (41.91cm x 41.91 cm) using two Map rectangles 2 ½ in x 12 ½ in (6.35 cm x 31.75 cm), two Map rectangles 2 ½ in x 16 ½ in (6.35 cm x 41.91cm) and the Fussy Cut Train 4-Panel square 12 ½ in x 12 ½ in (31.75 cm x 31.75 cm) as shown.

Dia. B

Panel 2 Unit

16 1⁄2 in x 16 1⁄2 in (41.91 cm x 41.91 cm)

3. Refer to Diagram C and Step 1 to make the Panel 3 Unit 16 ½ in x 16 ½ in (41.91cm x 41.91 cm) using two Fussy Cut Trains rectangles 2 ½ in x 12 ½ in (6.35 cm x 31.75 cm), two Fussy Cut Trains rectangles 2 ½ in x 16 ½ in (6.35 cm x 41.91cm) and the Fussy Cut Train 4-Panel square 12 ½ in x 12 ½ in (31.75 cm x 31.75 cm) as shown. Note: Check orientation of design.

Dia. C

Panel 3 Unit

16 1⁄2 in x 16 1⁄2 in (41.91 cm x 41.91 cm)

4. Refer to Diagram D and Step 1 to make the Panel 4 Unit 16 ½ in x 16 ½ in (41.91cm x 41.91 cm) using two Signs rectangles 2 ½ in x 12 ½ in (6.35 cm x 31.75 cm), two Signs rectangles 2 ½ in x 16 ½ in (6.35 cm x 41.91cm) and the Fussy Cut Train 4-Panel square 12 ½ in x 12 ½ in (31.75 cm x 31.75 cm) as shown.

Dia. D

Panel 4 Unit

16 1⁄2 in x 16 1⁄2 in (41.91 cm x 41.91 cm)

www.3wishesfabric.com

page 3

5. Place the four Panel Units in two rows as shown in Diagram E. Pin the pieces in each row RST, sew and press. Pin the rows RST matching seams, sew and press to make the Wall Hanging Center 32 ½ in x 32 ½ in (82.55 cm x 82.55 cm).

Dia. E Wall Hanging Center

+

=

+

+

=

=

32 1⁄2 in x 32 1⁄2 in (82.55 cm x 82.55 cm)

6. Refer to Diagram F to place the Borders around the Wall Hanging Center 32 ½ in x 32 ½ in (82.55 cm x 82.55 cm). Sew each Border RST in the order listed. Note: Check orientation of the design. Pin matching center and ends. Press seams as shown. Measure at each step to ensure the next border will fit. Tip: If one border is a little larger than the border it is being sewn to, pin well to ease the fullness and place the fullness on the bottom while sewing.

Circle Dots Borders (2) Sides – Circle Dots strips 2 ½ in x 32 ½ in (6.35 cm x 82.55 cm)

Steam in the Spring Wall Hanging Top Dia. F

+

(2) Top and Bottom – Circle Dots strips 2 ½ in x 34 ½ in (6.35 cm x 87.63 cm)

+

Wall Hanging Top – 34 ½ in x 34 ½ in (87.63 cm x 87.63 cm) Scenic Borders (2) Sides – Vertical Scenic rectangles 4 ½ in x 34 ½ in (11.43 cm x 107.95 cm) (2) Top and Bottom – Horizontal Scenic rectangles 4 ½ in x 42 ½ in (11.43 cm x 107.95 cm) +

+

+

+

The Steam in the Spring Wall Hanging Top should measure 42 ½ in x 42 ½ in (107.95 cm x 107.95 cm).

+ +

42 1⁄2 in x 42 1⁄2 in (107.95 cm x 107.95 cm)

www.3wishesfabric.com

page 4

Finishing 18. Remove the selvages from the Scenic Backing fabric. Cut two vertical pieces 11 1⁄2 in x 25 3⁄4 in (29.21 cm x 65.41 cm) and two vertical pieces 20 ¼ in x 51 in (51.44 cm x 129.54 cm). Pin the two smaller pieces RST on the short edges and sew as shown in Diagram G; press. Pin the larger pieces on each side and sew along the long edges. Note: Check orientation of the design. Press seams open or to one side. The Backing should measure 51 in x 51 in (129.54 cm x 129.54 cm).

Dia. G

Steam in the Spring Wall Hanging Top

11 1⁄2 in x 25 3⁄4 in

20 1⁄4 in x 51 in

20 1⁄4 in x 51 in

11 1⁄2 in x 25 3⁄4 in

51 in x 51 in (129.54 cm x 129.54 cm)

19. Press finished Quilt Top and Backing. Tape the Backing, wrong side up, to a firm surface. Layer Batting and Quilt Top (right side up). Baste the layers together with safety pins. Quilt as desired.

20. Once quilting is complete, square up corners and edges, trimming excess Backing and Batting even with the Quilt Top. 21. Follow Diagram H to make the Map Binding. Remove selvages and sew the short ends of the five 2 ½ in (6.35 cm) x wof strips RST end to end at a 45° angle to make one continuous strip; press seams open. Press one short end ¼ in (6.35 mm) to the wrong side.

Fold in half lengthwise with wrong sides together; press. Leaving a 2 in (5.08 cm) tail on the folded end, place cut edges of folded Binding even with the edge of the Quilt Top and sew, mitering the corners. Overlap ends, trim any excess and finish sewing the Binding. Fold Binding over to back and hand stitch.

Dia. H

Finished Care Instructions Machine wash in cold water; gentle cycle. Do not bleach. Tip: Before drying, check for fabric dyes that may have run. If fabric dyes run, rewash and rinse using a color catcher to absorb loose dye. Lay flat to dry or tumble dry low.

www.3wishesfabric.com

©2022 3 Wishes Fabric®

page 5

www.3wishesfabric.com

Follow us here to see more exciting projects and ideas!

Gardening Apron

Featuring the Touch of Spring Collection by Beth Albert Shipping to stores Jan 2022!

Finished Size: 15 1⁄2 in x 21 in (39.37 cm x 53.34 cm)

Fabric Needed 3 Wishes Fabric® Touch of Spring Collection • 3⁄4 yd – Garden Tools (18752-GRN-CTN-D) • 5⁄8 yd – Seed Packets (18753-BGE-CTN-D) Additional Supplies Needed: • Removable marker • Coordinating thread • Basic Sewing Supplies • Sewing machine • Iron and pressing surface

page 1

Before You Begin Read all instructions before beginning project. Do not pre-wash fabrics. Press fabrics with a dry iron on cotton setting before cutting.

Use a ¼ in (6.35 mm) seam allowance and sew fabrics with right sides together (RST) unless otherwise noted. Press seams in the direction of the arrows. wof = width of fabric

Cutting 4 in x 21 1⁄2 in

4 in x wof

14 in x 21 1⁄2 in

11 in x 21 1⁄2 in

Seed Packets (18753-BGE-CTN-D) 5⁄8 yard Cut 2 - 4 in (10.16 cm) x wof - Waist Ties Cut 1 – 11 in x 21 1⁄2 in (27.94 cm x 54.61 cm) - Pockets Garden Tools (18752-GRN-CTN-D) 3⁄4 yard Cut 2 - 14 in x 21 1⁄2 in (35.56 cm x 54.61 cm) - Apron & Apron Lining Cut 1 – 4 in x 21 1⁄2 in (10.16 cm x 54.61 cm) - Waistband

Sewing 1. Use a glass to draw a curve and cut a rounded corner on each side of the bottom edge 21 1⁄2 in (54.61 cm). Repeat for the bottom edge of the Apron Lining and Pocket (Dia. A).

Apron & Apron Lining

Dia. A

Cut

Trace

Pockets

2. To hem the top edge of the Seed Packet Pocket 11 in x 21 in (27.94 cm x 53.34 cm), press ¼ in (6.35 mm) to the wrong side. Press again ½ in (1.27 cm) to the wrong side and sew close to the inner fold (Dia. B).

Press 1⁄4 in (6.35 mm)

Dia. B Pocket Wrong side

www.3wishesfabric.com

Pocket Wrong side

Fold 1⁄2 in (1.27 cm) and sew close to inner edge

page 2

3. Place the Pocket right side up on the right side of the Garden Tools Apron 14 in x 21 ½ in (35.56 cm x 54.61 cm) with sides, curved corners and bottom edges matching; pin. Using a 1⁄8 in (3.18 mm) seam allowance, sew along the sides and bottom to attach the Pocket. Measure in 7 ¼ in (18.42 cm) from each side of the Pocket and draw a line from the top edge to the bottom edge. Sew along the two drawn lines to create three pockets (Dia. C).

Dia. C Sew 1⁄8 in (3.18 mm)

7 1⁄4 in (18.42 cm)

7 1⁄4 in (18.42 cm)

Pocket Right side

Sew

Sew

4. Refer to Diagram D to pin the Apron and Apron Lining with RST and edges even. Sew along the sides and bottom, turn right side out and press edges flat. Topstitch close to sewn edges. Baste the top edges of the Apron and Apron Lining together.

Topstitch close to edge

Dia. D

Baste Apron and Apron Lining together

Apron Right side Apron Lining Wrong side

5. Press Waistband in half longways with RST to form a center crease. Press one long edge of the Waistband ¼ in (6.35 mm) to the wrong side (Dia. E).

Dia. E

6.

Waistband Right side

Waistband Wrong side

Press to form center crease

Press 1⁄4 in (6.35 mm)

Center the Waistband on the front of the Apron and pin the cut edge to the top edge of the Apron with RST; sew and press (Dia. F). Note: Waistband will extend ¼ in (6.35 mm) on each side.

Dia. F

Apron Front

Note: 1⁄4 in (6.35 mm) of Waistband will extend on each side.

Waistband Right side

Align center Waistband Wrong side

Sew 1⁄4 in (6.35 mm)

Apron (Front)

Apron (Front)

6. Press one short end of a Waist Tie ¼ in (6.35 mm) to the wrong side. Fold long edges wrong sides together so they meet; press to create a crease. Open and fold each long edge ¼ in (6.35 mm) to the wrong side; press. Fold again so folded edges meet and press. Topstitch close to each folded edge (Dia. G). Repeat to make the other Waist Tie. Dia. G

Press short edge ¼ in (6.35 mm) Wrong side

www.3wishesfabric.com

Press long edges ¼ in (6.35 mm)

Wrong side

Crease

Fold & topstitch

Leave cut edge open

page 3

7. On the right side of the Waistband, pin the cut end of a Waist Tie to each side edge directly above the seam with edges matching.

Sew ¼ in (6.35 mm) from the edge to attach. Fold the Waistband with RST so side edges align; sew sides (Dia. H).

Dia. H

Sew 1⁄4 in (6.35 mm)

Sew 1⁄4 in (6.35 mm)

Sew 1⁄4 in (6.35 mm)

Sew 1⁄4 in (6.35 mm) Fold

Waistband Right side

Waistband (Wrong side)

Apron (Front)

Apron (Front)

Finishing 8. Turn the Waistband right side out and fold to the back; press. Align the folded edge to the Waistband seam and pin; hand stitch (Dia. I). Topstitch close to the bottom edge of the waistband on the right side.

Dia. I

Apron Lining (Back)

Finished Care Instructions Machine wash in cold water; gentle cycle. Do not bleach. Hang to dry.

www.3wishesfabric.com

page 4

www.3wishesfabric.com

Follow us here to see more exciting projects and ideas!

Dwelling Quilt Featuring the Touch of Spring Collection

by Beth Albert and the Good Vibes Collection by Courtney Morgenstern Shipping to stores January 2022

Finished Size: 54 ½ in x 56 ½ in (138.43 cm x 143.51 cm)

Fabric Needed 3 Wishes Fabric® Touch of Spring Collection • 1 Panel – Dwelling Panel (18751-PNL-CTN-D) • 2 yds – Shelves (18748-BLU-CTN-D) • 3/4 yd – Floral (18749-MLT-CTN-D) for Piecing and Binding • 1/2 yd – Bunnies (18746-PNK-CTN-D) • 3/8 yd – Bird Houses (18745-BLU-CTN-D) • 2 3/4 yds – Wagoneer (18747-WHT-CTN-D) for Backing

Additional Supplies Needed: • 63 in x 63 in Cotton batting • Piecing and sewing thread • Quilting and sewing supplies • Even-feed foot (optional for quilting)

3 Wishes Fabric® Good Vibes Collection • 1/2 yd – Circle Dots (18660-WOW-CTN-D)

page 1

Before You Begin Read all instructions before beginning project. Do not pre-wash fabrics. Press fabrics with a dry iron on cotton setting before cutting.

Use a ¼ in (6.35 mm) seam allowance and sew fabrics with right sides together (RST) unless otherwise noted. Press seams in the direction of the arrows. wof = width of fabric Note: A printed panel may become slightly skewed during the finishing process. Check if panel is square before cutting by folding the panel so selvages meet. If all edges do not meet, pull firmly from corner to corner until the edges meet. Continue until all corners are square.

Cutting Use a rotary cutter and ruler to cut the size and number of squares and rectangles from each fabric listed below.

4 ½ in x 28 ½ in

Dwelling Panel – 18751-PNL-CTN-D (36 in x wof / 91.44 cm x 106.68 cm) Fussy Cut 1 – 32 ½ in x 36 ½ in (82.55 cm x 90.17 cm) 2 ½ in x wof

4 ½ in x 23 ½ in

4 ½ in x 4 ½ in

Floral – 18749-MLT-CTN-D (¾ yd x wof / 68.58 cm x 106.68 cm) Cut 6 – 2 ½ in x wof (6.35 cm x 106.68 cm) for Binding Cut 12 – 4 ½ in x 4 ½ in (11.43 cm x 11.43 cm) 2 in x 24 ½ in

Shelves – 18748-BLU-CTN-D (2 yds x wof / 182.88 cm x 106.68 cm) Fussy Cut 4 – 4 ½ in x 28 ½ in (11.43 cm x 72.39 cm) Fussy Cut 4 – 4 ½ in x 23 ½ in (11.43 cm x 59.69 cm)

1 ½ in x 22 in

Bunnies – 18746-PNK-CTN-D (½ yd x wof / 45.72 cm x 106.68 cm) Cut 4 – 2 in x 24 ½ in (5.08 cm x 62.23 cm) Cut 4 – 1 ½ in x 22 in (3.81 cm x 55.88 cm)

www.3wishesfabric.com

page 2

2 in x 38 ½ in

3 ½ in x 10 ½ in

1 ½ in x 32 ½ in 1 ½ in x 10 ½ in

1 ½ in x 9 ½ in 3 ½ in x 9 ½ in Bird Houses – 18745-BLU-CTN-D (3⁄8 yd x wof / 34.29 cm x 106.68 cm) Cut 6 – 3 ½ in x 10 ½ in (8.89 cm x 26.67 cm) Cut 6 – 3 ½ in x 9 ½ in (3.81 cm x 24.13 cm)

Circle Dots – 18660-WOW-CTN-D (½ yd x wof / 45.72 cm x 106.68 cm) from the 3W Good Vibes Collection Cut 2 – 2 in x 38 ½ in (5.08 cm x 97.79 cm) Cut 2 – 1 ½ in x 32 ½ in (3.81 cm x 82.55 cm) Cut 6 – 1 ½ in x 10 ½ in (3.81 cm x 26.67 cm) Cut 6 – 1 ½ in x 9 ½ in (3.81 cm x 24.13 cm)

Sewing 1.

Place a Circle Dots strip 1 ½ in x 32 ½ in (3.81 cm x 82.55 cm) on each side of the Fussy Cut Dwelling Panel rectangle 32 ½ in x 36 ½ in (82.55 cm x 92.17 cm). Pin RST matching ends and centers, sew and press. Place a Circle Dots strip 2 in x 38 ½ in (5.08 cm x 97.79 cm) on the top and bottom. Pin RST matching ends and centers, sew and press. The Quilt Center should measure 35 ½ in x 38 ½ in (90.17 cm x 97.79 cm).

Dia. A Quilt Center +

+

+

+

2.

=

35 ½ in x 38 ½ in (90.17 cm x 97.79 cm)

Place a Circle Dots strip 1 ½ in x 9 ½ in (3.81 cm x 24.13 cm) and a vertical Bird Houses rectangle 3 ½ in x 9 ½ in (8.89 cm x 24.13 cm) oriented as shown in Diagram B. Pin RST, sew and press to make a Left Side Border Unit 4 ½ in x 9 ½ in (11.43 cm x 24.13 cm). Repeat to make three.

Left Side Border Unit

Dia. B

+

=

4 ½ in x 9 ½ in (11.43 cm x 24.13 cm) Make 3

www.3wishesfabric.com

page 3

3.

Follow Step 2 and Diagram C using three Circle Dots strips 1 ½ in x 9 ½ in (3.81 cm x 24.13 cm) and three Vertical Bird Houses rectangles 3 ½ in x 9 ½ in (8.89 cm x 24.13 cm) oriented as shown to make three Right Side Border Units 4 ½ in x 9 ½ in (11.43 cm x 24.13 cm).

Dia. C Right Side Border Unit

4 ½ in x 9 ½ in (11.43 cm x 24.13 cm) Make 3

4.

Follow Step 2 and Diagram D using three Circle Dots strips 1 ½ in x 10 ½ in (3.81 cm x 26.67 cm) and three horizontal Bird Houses rectangles 3 ½ in x 10 ½ in (8.89 cm x 26.67 cm) oriented as shown to make three Top Border Units 4 ½ in x 10 ½ in (11.43 cm x 26.67 cm).

Dia. D Top Border Unit

4 ½ in x 10 ½ in (11.43 cm x 26.67 cm) Make 3

5.

Follow Step 2 and Diagram E using three Circle Dots strips 1 ½ in x 10 ½ in (3.81 cm x 26.67 cm) and three horizontal Bird Houses rectangles 3 ½ in x 10 ½ in (8.89 cm x 26.67 cm) oriented as shown to make three Bottom Border Units 4 ½ in x 10 ½ in (11.43 cm x 26.67 cm).

Dia. E Bottom Border Unit

4 ½ in x 10 ½ in (11.43 cm x 26.67 cm) Make 3

6.

Alternate two Floral squares 4 ½ in x 4 ½ in (11.43 cm x 11.43 cm) with the three Left Side Border Units 4 ½ in x 9 ½ in (11.43 cm x 24.13 cm) oriented as shown in Diagram F. Pin RST, sew and press (toward the Floral squares) to make the Bird Houses Left Side Border 4 ½ in x 35 ½ in (11.43 cm x 90.17 cm).

Dia. F +

+

+

+

= Bird Houses Left Side Border

4 ½ in x 35 ½ in (11.43 cm x 90.17 cm)

7.

Follow Step 6 and Diagram G using two Floral squares 4 ½ in x 4 ½ in (11.43 cm x 11.43 cm) with the three Right Side Border Units 4 ½ in x 9 ½ in (11.43 cm x 24.13 cm) oriented as shown to make the Bird Houses Right Side Border 4 ½ in x 35 ½ in (11.43 cm x 90.17 cm.

Dia. G

Bird Houses Right Side Border

4 ½ in x 35 ½ in (11.43 cm x 90.17 cm)

8.

Follow Step 6 and Diagram H using four Floral squares 4 ½ in x 4 ½ in (11.43 cm x 11.43 cm) with the three Top Border Units 4 ½ in x 10 ½ in (11.43 cm x 26.67 cm) oriented as shown to make the Bird Houses Top Border 4 ½ in x 46 ½ in (11.43 cm x 118.11 cm).

Dia. H

Bird Houses Top Border

4 ½ in x 46 ½ in (11.43 cm x 118.11 cm)

www.3wishesfabric.com

page 4

9.

Follow Step 6 and Diagram I using four Floral squares 4 ½ in x 4 ½ in (11.43 cm x 11.43 cm) with the three Bottom Border Units 4 ½ in x 10 ½ in (11.43 cm x 26.67 cm) oriented as shown to make the Bird Houses Bottom Border 4 ½ in x 46 ½ in (11.43 cm x 118.11 cm).

Dia. I

Bird Houses Bottom Border

4 ½ in x 46 ½ in (11.43 cm x 118.11 cm)

10. Place two Bunnies strips 1 ½ in x 22 in (3.81 cm x 55.88 cm) as shown in Diagram J. Pin RST, sew and press open or to one side to make the Bunnies Side Border 1 ½ in x 43 ½ in (3.81 cm x 110.49 cm). Repeat to make two. Note: Check orientation of design.

Dia. J + = Bunnies Side Border 1 ½ in x 43 ½ in (3.81 cm x 110.49 cm) Make 2

11. Follow Step 10 and Diagram K using four Bunnies strips 2 in x 24 ½ in (5.08 cm x 62.23 cm) to make the Bunnies Top and Bottom Borders 2 in x 48 ½ in (11.43 cm x 123.19 cm).

Dia. K

Bunnies Top and Bottom Borders 2 in x 48 ½ in (5.08 cm x 123.19 cm) Make 2

12. Follow Step 10 and Diagram L using four Fussy Cut Shelves rectangles 4 ½ in x 23 ½ in (11.43 cm x 59.69 cm) matching fabric print at the center seam to make two Shelves Side Borders 4 ½ in x 46 ½ in (11.43 cm x 118.11 cm). Note: Check orientation of design.

Dia. L

Shelves Side Border

4 ½ in x 46 ½ in (11.43 cm x 118.11 cm) Make 2

13. Follow Step 10 and Diagram M using four Fussy Cut Shelves rectangles 4 ½ in x 28 ½ in (11.43 cm x 72.39 cm) to make the Shelves Top and Bottom Borders 4 ½ in x 46 ½ in (11.43 cm x 143.51 cm).

Dia. M

Shelves Top and Bottom Borders

4 ½ in x 56 ½ in (11.43 cm x 143.51 cm) Make 2

www.3wishesfabric.com

page 5

14. Refer to Diagram N to place the Borders around the Quilt Center 35 ½ in x 38 ½ in (90.17 cm x 97.79 cm). Note: Check orientation of design. Pin matching center, seams and ends. Sew each Border RST in the order listed. Press seams as shown. Measure at each step to ensure the next border will fit. Tip: If one border is a little larger than the border it is being sewn to, pin well to ease the fullness and place the fullness on the bottom while sewing.

Finished Quilt Top should measure 54 ½ in x 56 ½ in (138.43 cm x 143.51 cm).

Bird Houses Border Sides: 2 – Left and Right Side Borders 4 ½ in x 35 ½ in (11.43 cm x 90.17 cm); made in Steps 6 and 7 Top and Bottom: Top and Bottom Borders 4 ½ in x 46 ½ in (11.43 cm x 118.11 cm); made in Steps 8 and 9 Quilt Top - 43 ½ in x 46 ½ in (110.49 cm x 118.11 cm).

Bunnies Border Sides: 2 – Side Borders 1 ½ in x 43 ½ in (3.81 cm x 110.49 cm); made in Step 10 Top and Bottom: 2 – Top and Bottom Borders 2 in x 48 ½ in (5.08 cm x 123.19 cm); made in Step 11 Quilt Top - 46 ½ in x 48 ½ in (118.11 cm x 123.19 cm).

Shelves Border Sides: 2 – Side Borders 4 ½ in x 46 ½ in (11.43 cm x 123.19 cm); made in Step 12 Top and Bottom: 2 – Top and Bottom Borders 4 ½ in x 56 ½ in (11.43 cm x 143.51 cm); made in Step 13 Quilt Top - 54 ½ in x 56 ½ in (138.43 cm x 143.51 cm).

Dia. N

Touch of Spring Dwelling Quilt

+ +

+

+

+

+

+

+

+

+

+ +

54 ½ in x 56 ½ in (138.43 cm x 143.51 cm)

www.3wishesfabric.com

page 6

Finishing

Dia. O

15. Remove the selvages from the Wagoneer Backing fabric.

Note: Check orientation of designs. Cut one piece 41 ¾ in x 63 in (106.05 cm x 160.02 cm) and two pieces 21 ¼ in x 31 ¾ in (55.25 cm x 80.65 cm). Pin RST and sew the two smaller pieces on the short edges; press. Pin the two sections RST and sew along the long edges as shown in Diagram O. Press the seam open or to one side. The Backing should measure 62 ½ in x 63 in (158.75 cm x 160.02 cm).

21 ¼ in x 31 ¾in (55.25 cm x 80.65 cm)

41 ¾ in x 63 in (106.05 cm x 160.02 cm)

16. Press finished Quilt Top and Backing. Tape the Backing, wrong side up, to a firm surface. Layer Batting and Quilt Top (right side up. Baste the layers together with safety pins.

Quilt as desired.

17. Once quilting is complete, square up corners and edges, trimming excess Backing and Batting even with the Quilt Top.

21 ¼ in x 31 ¾in (55.25 cm x 80.65 cm)

Backing 62 ½ in x 63 in (158.75 cm x 160.02 cm)

18. Binding – Follow Diagram P to make the Floral Binding. Remove selvages and sew the short ends of the six 2 ½ in (6.35 cm) x wof strips RST end to end at a 45° angle to make one continuous strip; press seams open. Press one short end ¼ in (6.35 mm) to the wrong side. Fold in half lengthwise with wrong sides together; press. Leaving a 2 in (5.08 cm) tail on the folded end, place cut edges of folded Binding even with the edge of the Quilt Top and sew, mitering the corners. Overlap ends, trim any excess and finish sewing the Binding. Fold Binding over to back and hand stitch.

Dia. P

Stop stitching ¼ in (6.35 mm) from end of quilt

Finished Care Instructions Machine wash in cold water; gentle cycle. Do not bleach. Tip: Before drying, check for fabric dyes that may have run. If fabric dyes run, rewash and rinse using a color catcher to absorb loose dye. Lay flat to dry or tumble dry low.

www.3wishesfabric.com

©2022 3 Wishes Fabric®

page 7

www.3wishesfabric.com

Follow us here to see more exciting projects and ideas!

Garden Flags

Featuring the Touch of Spring Collection

by Beth Albert and the Good Vibes Collection

by Courtney Morgenstern Shipping to stores January 2022

Finished Size: 12 ½ in x 18 in (31.75 cm x 45.72 cm) each

Fabric Needed 3 Wishes Fabric® Touch of Spring Collection • 1 Panel – Dwelling Panel (18751-PNL-CTN-D) • 5⁄8 yd – Shelves (18748-BLU-CTN-D ) • 5⁄8 yd – Seed Packets (18753-BGE-CTN-D) • 3/8 yd – Bird Houses (18745-BLU-CTN-D) 3 Wishes Fabric® Good Vibes Collection • 1/8 yd – Circle Dots (18660-WOW-CTN-D)

Additional Supplies Needed: • 2 Garden Flag Stands • Piecing and sewing thread • Removable marker • Basic Sewing Supplies • Sewing machine • Iron and pressing surface

page 1

Before You Begin Read all instructions before beginning project. Do not pre-wash fabrics. Press fabrics with a dry iron on cotton setting before cutting.

Use a ¼ in (6.35 mm) seam allowance and sew fabrics with right sides together (RST) unless otherwise noted. Press seams in the direction of the arrows. wof = width of fabric Note: A printed panel may become slightly skewed during the finishing process. Check if panel is square before cutting by folding the panel so selvages meet. If all edges do not meet, pull firmly from corner to corner until the edges meet. Continue until all corners are square.

Cutting Use a rotary cutter and ruler to cut the size and number of squares and rectangles from each fabric listed below.

5 in x 13 in

13 in x 18 ½ in

10 in x 10 in

Seed Packets – 18753-BGE-CTN-D (5⁄8 yd x wof / 57.15 cm x 106.68 cm) Cut 1 – 13 in x 18 ½ in (5.08 cm x 74.93 cm) for Flag Back Cut 1 – 5 in x 13 in (5.08 cm x 71.12 cm) for Flag Botttom 2 in x 13 in

Dwelling Panel – 18751-PNL-CTN-D (36 in x wof / 91.44 cm x 106.68 cm) Fussy Cut 2 – 10 in x 10 in (25.4 cm x 25.4 cm) for Flag Centers 1 ½ in x 11 in 5 in x 13 in

13 in x 18 ½ in

Bird Houses – 18754-BLU-CTN-D (3⁄8 yd x wof / 34.29 cm x 106.68 cm) Cut 4 – 1 ½ in x 11 in (3.81 cm x 27.94 cm) Vertical Cut 2 – 2 in x 13 in (5.08 x 33.02 cm) Horizontal 1 in x 10 in 1 in x 11 in

Circle Dots – 18660-WOW-CTN-D (1⁄8 yd x wof / 11.43 cm x 106.68 cm) from the 3W Good Vibes Collection Cut 4 – 1 in x 10 in (2.54 cm x 25.4 cm) Cut 4 – 1 in x 11 in (2.54 cm x 27.94 cm)

Shelves – 18748-BLU-CTN-D (5⁄8 yd x wof / 57.15 cm x 106.68 cm) Cut 1 – 13 in x 18 ½ in (5.08 cm x 74.93 cm) for Flag Back Cut 1 – 5 in x 13 in (5.08 cm x 71.12 cm) for Flag Botttom

www.3wishesfabric.com

page 2

Sewing 1.

Refer to Diagram A to place the Borders around the Flag Center 10 in x 10 in (25.4 cm x 25.4 cm). Sew each Border RST in the order listed. Pin matching middle and ends. Note: Check direction of the design. Press seams as shown. Check at each step to ensure the next Border will fit. Tip: If one Border is a little larger that the Border it is being sewn to, pin well to ease the fullness and place the fullness on the bottom while sewing.

White Circle Dots Borders Sides: 2 rectangles 1 in x 10 in (2.54 cm x 25.4 cm) Top and Bottom: 2 rectangles 1 in x 11 in (2.54 cm x 27.94 cm) Bird Houses Borders Sides: 2 rectangles 1 ½ in x 11 in (3.81 cm x 27.94 cm) vertical Top and Bottom: 2 rectangles 2 in x 13 in (5.08 cm x 33.02 cm) horizontal Dia. A

+ +

+

+

+

+

=

+ +

www.3wishesfabric.com

13 in x 14 in (33.02 cm x 35.56 cm)

page 3

2.

Pin the Shelves Flag Bottom 5 in x 13 in (12.7 cm x 33.02 cm) RST to the bottom Tree Houses Border with edges even; sew and press (Dia. B). Note: Check direction of the design.

Dia. B

=

+

13 in x 18 ½ in (33.02 cm x 46.99 cm)

3.

Pin the top edge of the Flag to the top edge of the Lining RST. Note: Check the direction of the design. Sew and press seam open (Dia. C).

Dia. C

Lining (right side)

Garden Flag wrong side

www.3wishesfabric.com

Sew and press seam open

page 4

4.

Refer to Diagram D to measure 1 in (2.54 cm) away from the seam on both the Flag and Lining and make a mark on each edge.

At each mark, clip in ¼ in (6.35 mm).

Dia. D

Measure 1 in (2.54 cm) from seam on both sides and mark.

Clip in ¼ in (6.35 mm)

1 in (2.54 cm)

1 in (2.54 cm)

Lining wrong side

Garden Flag wrong side

1 in (2.54 cm)

1 in (2.54 cm)

Measure 1 in (2.54 cm) from seam on both sides and mark.

Clip in ¼ in (6.35 mm)

5.

Press the clipped area ¼ in (6.35 mm) to the wrong side. Sew close to the inner edge (Dia. E).

Dia. E

Cut, press to wrong side, sew close to inner edge.

Lining wrong side

Garden Flag wrong side

Cut, press to wrong side, sew close to inner edge.

www.3wishesfabric.com

page 5

6.

Fold the Flag RST with edges even; pin. Sew around the cut edges leaving a 3 in (7.62 cm) opening in the bottom for turning (Dia. F). Turn right side out and press the edges at the opening to the inside. Press all edges flat.

Dia. F

Garden Flag wrong side

Leave 3 in (7.62 cm) opening

Finishing 7.

On the right side, measure down 1 in (2.54 cm) from the top edge and topstitch across the Flag to create the casing. Topstitch close to the side and bottom edges which will close opening in the bottom (Dia. G).

8.

Follow Steps 1 through 7 and use the remaining pieces to create the second Garden Flag.

Dia. G

Create casing 1 in (2.54 cm) from top edge

Topstitch

12 ½ in x 18 in (31.75 cm x 45.72 cm)

Finished Care Instructions Machine wash gentle, cold water. Do not bleach. Hang to dry. www.3wishesfabric.com

©2022 3 Wishes Fabric®

page 6

www.3wishesfabric.com

Follow us here to see more exciting projects and ideas!

Town Quilt

Featuring the Touch of Spring Collection

by Beth Albert Shipping to stores January 2022

Finished Size: 73 in x 73 in (185.42 cm x 185.42 cm)

Fabric Needed 3 Wishes Fabric® Touch of Spring Collection • 1 Panel – Town Panel (18744-PNL-CTN-D) • 1 Panel – Dwelling Panel (18751-PNL-CTN-D) • 1 1/4 yds – Shelves (18748-BLU-CTN-D) for Piecing and Binding • 3/4 yd – Floral (18749-MLT-CTN-D) • 1/2 yd – Garden Tools (18752-GRN-CTN-D) • 1/2 yd – Seed Packets (18753-BGE-CTN-D) • 1/8 yd – Bunnies (18746-PNK-CTN-D) • 4 1/2 yds – Spring Patch (18750-WHT-CTN-D) for Backing

Additional Supplies Needed: • 81 in x 81 in Cotton batting • Piecing and sewing thread • Quilting and sewing supplies • Even-feed foot (optional for quilting)

3 Wishes Fabric® Good Vibes Collection • 2 1/8 yds – Circle Dots (18660-WOW-CTN-D)

page 1

Before You Begin Read all instructions before beginning project. Do not pre-wash fabrics. Press fabrics with a dry iron on cotton setting before cutting.

Use a ¼ in (6.35 mm) seam allowance and sew fabrics with right sides together (RST) unless otherwise noted. Press seams in the direction of the arrows. wof = width of fabric Note: A printed panel may become slightly skewed during the finishing process. Check if panel is square before cutting by folding the panel so selvages meet. If all edges do not meet, pull firmly from corner to corner until the edges meet. Continue until all corners are square.

Cutting Use a rotary cutter and ruler to cut the size and number of squares and rectangles from each fabric listed below.

2 in x 35 ½ in 2 in x 32 ½ in 1 ½ in x 26 ½ in 1 ½ in x 24 ½ in

5 ½ in x 10 ½ in

24 ½ in x 24 ½ in

7 ¾ in x 7 ¾ in Town Panel – 18744-PNL-CTN-D (36 in x wof / 91.44 cm x 106.68 cm) Fussy Cut 1 – 24 ½ in x 24 ½ in (62.23 cm x 62.23 cm)

10 ½ in x 10 ½ in

11 in x 11 in

Dwelling Panel – 18751-PNL-CTN-D (36 in x wof / 91.44 cm x 106.68 cm) Fussy Cut 8 – 10 ½ in x 10 ½ in (26.67 cm x 26.67 cm)

www.3wishesfabric.com

Circle Dots – 18660-WOW-CTN-D (2 1⁄8 yds x wof / 194.31 cm x 106.68 cm) from the 3W Good Vibes Collection Cut 2 – 2 in x 35 ½ in (5.08 cm x 90.17 cm) Cut 2 – 2 in x 32 ½ in (5.08 cm x 82.55 cm) Cut 2 – 1 ½ in x 26 ½ in (3.81 cm x 67.31 cm) Cut 2 – 1 ½ in x 24 ½ in (3.81 cm x 62.23 cm) Cut 12 – 5 ½ in x 10 ½ in (13.97 cm x 26.67 cm) Cut 18 – 7 ¾ in x 7 ¾ in (19.69 cm x 19.69 cm) Cut 2 – 11 in x 11 in (27.94 cm x 27.94 cm)

page 2

2 ½ in x wof 7 ¾ in x 7 ¾ in

2 in x 29 ½ in

Garden Tools – 18752-GRN-CTN-D (½ yd x wof / 45.72 cm x 106.68 cm) Cut 9 – 7 ¾ in x 7 ¾ in (19.69 cm x 19.69 cm)

7 ¾ in x 7 ¾ in 2 in x 28 in

Seed Packets – 18753-BGE-CTN-D (½ yd x wof / 45.72 cm x 106.68 cm) Cut 9 – 7 ¾ in x 7 ¾ in (19.69 cm x 19.69 cm) Shelves – 18748-BLU-CTN-D (1 ¼ yds x wof / 114.3 cm x 106.68 cm) Cut 8 – 2 ½ in x wof (6.35 cm x 106.68 cm) for Binding Cut 4 – 2 in x 29 ½ in (5.08 cm x 74.93 cm) Cut 4 – 2 in x 28 in (5.08 cm x 71.12 cm) 3 ½ in x 26 ½ in

3 ½ in x 3 ½ in Bunnies – 18746-PNK-CTN-D (1⁄8 yd x wof / 11.43 cm x 106.68 cm) Cut 4 – 3 ½ in x 3 ½ in (8.89 cm x 8.89 cm)

11 in x 11 in

Floral – 18749-MLT-CTN-D (¾ yd x wof / 68.58 cm x 106.68 cm) Cut 4 – 3 ½ in x 26 ½ in (8.89 cm x 67.31 cm) Cut 2 – 11 in x 11 in (27.94 cm x 27.94 cm)

www.3wishesfabric.com

page 3

Sewing 1.

Place a Bunnies square 3 ½ in x 3 ½ in (8.89 cm x 8.89 cm) on each side of a Floral rectangle 3 ½ in x 26 ½ in (8.89 cm x 67.31 cm) as shown in Diagram A. Note: Check orientation of design. Pin RST, sew and press to make the Floral Top Border 3 ½ in x 32 ½ in (8.89 cm x 82.55 cm). Repeat to make the Floral Bottom Border.

Dia. A

Floral Top and Bottom Border +

+

= 3 ½ in x 32 ½ in (8.89 cm x 82.55 cm) Make 2

2.

Refer to Diagram B to place the Borders around the Fussy Cut Town Panel 24 ½ in x 24 ½ in (62.23 cm x 62.23 cm). Sew each Border RST in the order listed. Pin matching center, seams and ends. Note: Check orientation of design. Press seams as shown.

Measure at each step to ensure the next border will fit. Tip: If one border is a little larger than the border it is being sewn to, pin well to ease the fullness and place the fullness on the bottom while sewing. The Quilt Center should measure 35 ½ in x 35 ½ in (90.17 cm x 90.17 cm).

Inner Circle Dots Border Sides: 2 – Circle Dots strips 1 ½ in x 24 ½ in (3.81 cm x 62.23 cm) Top and Bottom: 2 – Circle Dots strips 1 ½ in x 26 ½ in (3.81 cm x 67.31 cm) Quilt Center – 26 ½ in x 26 ½ in (67.31 cm x 67.31 cm).

Floral Border Sides: 2 – Floral rectangles 3 ½ in x 26 ½ in (8.89 cm x 67.31 cm) Top and Bottom: Top and Bottom Borders 3 ½ in x 32 ½ in (8.89 cm x 82.55 cm); made in Step 1 Quilt Top – 32 ½ in x 32 ½ in (82.55 cm x 82.55 cm).

Outer Circle Dots Border Sides: 2 – Circle Dots strips 2 in x 32 ½ in (5.08 cm x 82.55 cm) Top and Bottom: 2 – Circle Dots strips 2 in x 35 ½ in (5.08 cm x 90.17 cm) Quilt Center – 35 ½ in x 35 ½ in (90.17 cm x 90.17 cm).

Dia. B

Quilt Center +

+ +

+

+

+

+

+

+

+ +

+ 35 ½ in x 35 ½ in (90.17 cm x 90.17 cm)

www.3wishesfabric.com

page 4

3.

Draw a diagonal line on the wrong side of a Circle Dots square 11 in x 11 in (27.94 cm x 27.94 cm) as shown in Diagram C. Place on top of a Floral square 11 in x 11 in (27.94 cm x 27.94 cm) RST and sew ¼ in (6.35 mm) away from the line on both sides. Cut on the drawn line; press and trim if necessary. Note: Two squares yield two Half-Square Triangle (HST) Units. Repeat to make a total of four Half-Square Triangle Units 10 ½ in x 10 ½ in (26.67 cm x 26.67 cm).

Dia. C

Sew

Draw wrong side

4.

Half-Square Triangle Unit

¼ in (6.35 mm)

Cut

Press

Square up to 10 ½ in x 10 ½ in (26.67 cm x 26.67 cm) Make 4

Place three Circle Dots rectangles 5 ½ in x 10 ½ in (13.97 cm x 26.67 cm) with two Fussy Cut Dwelling Panel squares 10 ½ in x 10 ½ in (26.67 cm x 26.67 cm) as shown in Diagram D. Pin RST, sew and press toward the Dwelling squares to make the Dwelling Left Side Border 10 ½ in x 35 ½ in (26.67 cm x 90.17 cm).

Dia. D

+

+

+

+

= Dwelling Left Side Border

10 ½ in x 35 ½ in (26.67 cm x 90.17 cm)

5.

Follow Step 4 and Diagram E using three Circle Dots rectangles 5 ½ in x 10 ½ in (13.97 cm x 26.67 cm) and two Fussy Cut Dwelling Panel squares 10 ½ in x 10 ½ in (26.67 cm x 26.67 cm) as shown to make the Dwelling Right Side Border 10 ½ in x 35 ½ in (26.67 cm x 90.17 cm).

Dia. E

Dwelling Right Side Border

10 ½ in x 35 ½ in (26.67 cm x 90.17 cm)

www.3wishesfabric.com

page 5

6.

Follow Step 4 and Diagram F using three Circle Dots rectangles 5 ½ in x 10 ½ in (13.97 cm x 26.67 cm), two Fussy Cut Dwelling Panel squares 10 ½ in x 10 ½ in (26.67 cm x 26.67 cm) and two HST Units as shown to make the Dwelling Top Border 10 ½ in x 55 ½ in (26.67 cm x 104.97 cm); press.

Dia. F

Dwelling Top Border

10 ½ in x 55 ½ in (26.67 cm x 140.97 cm)

7.

Follow Step 4 and Diagram G using three Circle Dots rectangles 5 ½ in x 10 ½ in (13.97 cm x 26.67 cm), two Fussy Cut Dwelling Panel squares 10 ½ in x 10 ½ in (26.67 cm x 26.67 cm) and two HST Units as shown to make the Dwelling Bottom Border 10 ½ in x 55 ½ in (26.67 cm x 140.97 cm).

Dia. G

Dwelling Bottom Border

10 ½ in x 55 ½ in (26.67 cm x 140.97 cm)

8.

Place two Shelves strips 2 in x 28 in (5.08 cm x 71.12 cm) as shown in Diagram H. Pin RST, sew and press open to make the Shelves Side Border 2 in x 55 ½ in (50.8 cm x 140.97 cm). Note: Check orientation of design. Repeat to make two.

Dia. H + = Shelves Side Border 2 in x 55 ½ in (5.08 cm x 140.97 cm) Make 2

9.

Follow Step 8 and Diagram I using four Shelves strips 2 in x 29 ½ in (5.08 cm x 74.93 cm) to make the Shelves Top and Bottom Borders 2 in x 58 ½ in (5.08 cm x 148.59 cm).

Dia. I

Shelves Top and Bottom Border 2 in x 58 ½ in (5.08 cm x 148.59 cm) Make 2

www.3wishesfabric.com

page 6

10. Place four Circle Dots, two Seed Packets and two Garden Tools squares 7 ¾ in x 7 ¾ in (19.69 cm x 19.69 cm) as shown in Diagram J. Note: Check orientation of design. Pin RST, sew and press away from the Circle Dots squares to make the Outer Left Side Border 7 ¾ in x 58 ½ in (19.69 cm x 148.59 cm).

Dia. J

+

+

+

+

+

+

+

= Outer Left Side Border

7 ¾ in x 58 ½ in (5.08 cm x 148.59 cm)

11. Follow Step 10 and Diagram K using four Circle Dots, two Seed Packets and two Garden Tools squares 7 ¾ in x 7 ¾ in (19.69 cm x 19.69 cm) as shown. Pin RST, sew and press to make the Outer Right Side Border 7 ¾ in x 58 ½ in (19.69 cm x 148.59 cm).

Dia. K

Outer Right Side Border

7 ¾ in x 58 ½ in (5.08 cm x 148.59 cm)

12. Follow Step 10 and Diagram L using five Circle Dots, three Seed Packets and two Garden Tools squares 7 ¾ in x 7 ¾ in (19.69 cm x 19.69 cm) as shown. Pin RST, sew and press to make the Outer Top Border 7 ¾ in x 73 in (19.69 cm x 185.42 cm).

Dia. L

Outer Top Border

7 ¾ in x 73 in (5.08 cm x 185.42 cm)

13. Follow Step 10 and Diagram M using five Circle Dots, two Seed Packets and three Garden Tools squares 7 ¾ in x 7 ¾ in 19.69 cm x 19.69 cm) as shown. Pin RST, sew and press to make the Outer Bottom Border 7 ¾ in x 73 in (19.69 cm x 185.42 cm).

Dia. M

Outer Bottom Border

7 ¾ in x 73 in (5.08 cm x 185.42 cm)

www.3wishesfabric.com

page 7

14. Refer to Diagram N to place the Borders around the Quilt Center 35 ½ in x 35 ½ in (90.17 cm x 90.17 cm). Sew each Border RST in the order listed. Pin matching center, seams and ends. Press seams as shown. Measure at each step to ensure the next border will fit. Tip: If one border is a little larger than the border it is being sewn to, pin well to ease the fullness and place the fullness on the bottom while sewing. Finished Quilt Top should measure 73 in x 73 in (185.42 cm x 185.42 cm).

Dwelling Border Sides: Left and Right Side Borders 10 ½ in x 35 ½ in (26.67 cm x 90.17 cm); made in Steps 4 and 5 Top and Bottom: Top and Bottom Borders 10 ½ in x 55 ½ in (26.67 cm x 140.97 cm); made in Steps 6 and 7 Quilt Top - 55 ½ in x 55 ½ in (140.97 cm x 140.97 cm).

Shelves Border Sides: 2 – Side Borders 2 in x 55 ½ in (5.08 cm x 140.97 cm); made in Step 8 Top and Bottom: 2 – Top and Bottom Borders 2 in x 58 ½ in (5.08 cm x 148.59 cm); made in Step 9 Quilt Top - 58 ½ in x 58 ½ in (148.59 cm x 148.59 cm).

Outer Border Sides: Side Borders 7 ¾ in x 58 ½ in (19.69 cm x 185.42 cm); made in Steps 10 and 11 Top and Bottom: Top and Bottom Borders 7 ¾ in x 73 in (19.69 cm x 185.42 cm); made in Steps 12 and 13 Quilt Top – 73 in x 73 in (185.42 cm x 185.42 cm).

Dia. N

Touch of Spring Town Quilt Top

+ +

+

+

+

+

+

+

+

+

+ +

73 in x 73 in (185.42 cm x 185.42 cm)

www.3wishesfabric.com

page 8

Finishing

Dia. O

15. Remove the selvages from the Spring Patch Backing fabric.

Note: Check orientation of design. Cut two pieces 40 ¾ in x 81 in (103.51 cm x 205.74 cm). Pin the two sections RST and sew along the long edges as shown in Diagram O. Press the seam open or to one side. The Backing should measure 81 in x 81 in (205.74 cm x 205.74 cm).

16. Press finished Quilt Top and Backing. Tape the Backing, wrong side up, to a firm surface. Layer Batting and Quilt Top (right side up). Baste the layers together with safety pins. Quilt as desired.

40 ¾ in x 81 in (103.51 cm x 205.74 cm)

40 ¾ in x 81 in (103.51 cm x 205.74 cm)

17. Once quilting is complete, square up corners and edges, trimming excess Backing and Batting even with the Quilt Top.

Backing 81 in x 81 in (205.74 cm x 205.74 cm)

18. Binding – Follow Diagram P to make the Shelves Binding. Remove selvages and sew the short ends of the eight 2 ½ in (6.35 cm) x wof strips RST end to end at a 45° angle to make one continuous strip; press seams open. Press one short end ¼ in (6.35 mm) to the wrong side. Fold in half lengthwise with wrong sides together; press. Leaving a 2 in (5.08 cm) tail on the folded end, place cut edges of folded Binding even with the edge of the Quilt Top and sew, mitering the corners. Overlap ends, trim any excess and finish sewing the Binding. Fold Binding over to back and hand stitch.

Dia. P

Stop stitching ¼ in (6.35 mm) from end of quilt

Finished Care Instructions Machine wash in cold water; gentle cycle. Do not bleach. Tip: Before drying, check for fabric dyes that may have run. If fabric dyes run, rewash and rinse using a color catcher to absorb loose dye. Lay flat to dry or tumble dry low.

www.3wishesfabric.com

©2022 3 Wishes Fabric®

page 9

www.3wishesfabric.com

Follow us here to see more exciting projects and ideas!

Squad Quilt Featuring the Welcome to the Funny Farm Collection

by Connie Haley and the Good Vibes Collection

by Courtney Morgenstern Shipping to stores January 2022

Finished Size: 68 ½ in x 68 ½ in (173.99 cm x 173.99 cm)

Fabric Needed 3 Wishes Fabric® Welcome to the Funny Farm Collection • 1 Panel – Farm Squad Panel (18727-PNL-CTN-D) • 1 5/8 yds – Hens (18733-WHT-CTN-D) • 1 1/2 yds – Tossed Animals (18728-TRQ-CTN-D) • 1 1/4 yds – Tractors (18735-RED-CTN-D) for Piecing and Binding • 1 yd – Animal Patch (18731-MLT-CTN-D) • 3/4 yd – Gingham (18730-RED-CTN-D) • 3/8 yd – Veggies (18732-MLT-CTN-D) • 1/4 yd – Carrots (18734-MLT-CTN-D) • 4 1/4 yds – Gingham (18730-RED-CTN-D) for Backing

Additional Supplies Needed: • 76 in x 76 in Cotton batting • Piecing and sewing thread • Quilting and sewing supplies • Even-feed foot (optional for quilting)

3 Wishes Fabric® Good Vibes Collection • 1/4 yd – Circle Dots (18660-WOW-CTN-D)

page 1

Before You Begin Read all instructions before beginning project. Do not pre-wash fabrics. Press fabrics with a dry iron on cotton setting before cutting.

Use a ¼ in (6.35 mm) seam allowance and sew fabrics with right sides together (RST) unless otherwise noted. Press seams in the direction of the arrows. wof = width of fabric Note: A printed panel may become slightly skewed during the finishing process. Check if panel is square before cutting by folding the panel so selvages meet. If all edges do not meet, pull firmly from corner to corner until the edges meet. Continue until all corners are square.

Cutting Use a rotary cutter and ruler to cut the size and number of squares and rectangles from each fabric listed below.

10 ½ in x 38 ½ in

20 ½ in x 38 ½ in

4 ½ in x 30 ½ in

Farm Squad Panel – 18727-PNL-CTN-D (24 in x wof / 60.96 cm x 106.68 cm) Fussy Cut 1 – 20 ½ in x 38 ½ in (52.07 cm x 97.79 cm)

10 ½ in x 20 ½ in

Tossed Animals – 18728-TRQ-CTN-D (1 ½ yds x wof / 173.16 cm x 106.68 cm) Cut 1 – 10 ½ in x 38 ½ in (26.67 cm x 97.79 cm) Cut 8 – 4 ½ in x 30 ½ in (11.43 cm x 77.47 cm)

10 ½ in x 10 ½ in

Hens – 18733-WHT-CTN-D (1 5⁄8 yds x wof / 148.59 cm x 106.68 cm) Cut 8 – 10 ½ in x 20 ½ in (26.67 cm x 52.07 cm) Cut 2 – 10 ½ in x 10 ½ in (26.67 cm x 26.67 cm)

www.3wishesfabric.com

page 2

2 ½ in x wof 10 ½ in x 10 ½ in

10 ½ in x 10 ½ in

Gingham – 18730-RED-CTN-D (¾ yd x wof / 68.58 cm x 106.68 cm) Cut 8 – 10 ½ in x 10 ½ in (26.67 cm x 26.67 cm)

5 ½ in x 38 ½ in 4 ½ in x 4 ½ in

Tractors – 18735-RED-CTN-D (1 ½ yds x wof / 173.16 cm x 106.68 cm) Cut 7 – 2 ½ in x wof (6.35 cm x 106.68 cm) for Binding Cut 8 – 10 ½ in x 10 ½ in (26.67 cm x 26.67 cm)

Veggies – 18732-MLT-CTN-D (3⁄8 yd x wof / 34.29 cm x 106.68 cm) Cut 1 – 5 ½ in x 38 ½ in (13.97 cm x 97.79 cm) Cut 4 – 4 ½ in x 4 ½ in (11.43 cm x 11.43 cm)

3 ½ in x 38 ½ in

10 ½ in x 10 ½ in

Carrots – 18734-MLT-CTN-D (¼ yd x wof / 22.86 cm x 106.68 cm) Cut 1 – 3 ½ in x 38 ½ in (8.89 cm x 97.79 cm) 1 ½ in x 40 ½ in 1 ½ in x 38 ½ in Circle Dots – 18660-WOW-CTN-D (¼ yd x wof / 68.58 cm x 106.68 cm) from the 3W Good Vibes Collection Cut 2 – 1 ½ in x 40 ½ in (3.81 cm x 102.87 cm) Cut 2 – 1 ½ in x 38 ½ in (3.81 cm x 97.79 cm)

Animal Patch – 18731-MLT-CTN-D (1 yd x wof / 91.44 cm x 106.68 cm) Fussy Cut 4 – 10 ½ in x 10 ½ in (26.67 cm x 26.67 cm)

www.3wishesfabric.com

page 3

Sewing 1.

Referring to Diagram A, draw a diagonal line on the wrong side of a Hens square (10 ½ in x 10 ½ in / 26.67 cm x 26.67 cm). Place RST on the left side of the Tossed Animals rectangle (10 ½ in x 38 ½ in / 26.67 cm x 97.79 cm). Sew on the diagonal line. Trim seam to ¼ in (6.35 mm); press. Repeat with a second Hens square (10 ½ in x 10 ½ in / 26.67 cm x 26.67 cm) on the right side of the rectangle to make Row 1 (10 ½ in x 38 ½ in / 26.67 cm x 97.79 cm).

Dia. A

Draw wrong side

Sew

¼ in (6.35 mm)

Row 1

Press

Cut

2.

10 ½ in x 38 ½ in (26.67 cm x 97.79 cm)

Place Row 1 (10 ½ in x 38 ½ in / 26.67 cm x 97.79 cm) with the Fussy Cut Farm Squad Panel rectangle (20 ½ in x 38 ½ in / 52.07 cm x 97.79 cm), the Carrots rectangle (3 ½ in x 38 ½ in / 8.89 cm x 97.79 cm) and the Veggies rectangle (5 ½ in x 38 ½ in / 13.97 cm x 97.79 cm) in four Rows as shown in Diagram B. Note: Check orientation of designs. Pin RST matching ends and middles, sew and press. The Center Unit should measure 38 ½ in x 38 ½ in (97.79 cm x 97.79 cm).

Dia. B

Center Unit

Row 1

+

Row 2

+ Row 3 + Row 4 38 ½ in x 38 ½ in (97.79 cm x 97.79 cm)

www.3wishesfabric.com

page 4

3.

Place a Circle Dots strip (1 ½ in x 38 ½ in / 3.81 cm x 97.79 cm) on each side of the Center Unit (38 ½ in x 38 ½ in / 97.79 cm x 97.79 cm). Pin RST matching ends and centers, sew and press. Place a Circle Dots strip (1 ½ in x 40 ½ in / 3.81 cm x 102.87 cm) on the top and bottom. Pin RST matching ends and centers, sew and press. The Center Section should measure 40 ½ in x 40 ½ in (102.87 cm x 102.87 cm).

Dia. C Center Section

+

+

+

=

+

4.

40 ½ in x 40 ½ in (402.87 cm x 102.87 cm)

Refer to Diagram D to make the Flying Geese Units. Draw a diagonal line on the wrong side of a Gingham square (10 ½ in x 10 ½ in / 26.67 cm x 26.67 cm). Place RST on the left side of a Hens rectangle (10 ½ in x 20 ½ in / 26.67 cm x 52.07 cm). Sew on the diagonal line. Trim seam to ¼ in (6.35 mm); press. Repeat with a Tractors square (10 ½ in x 10 ½ in / 26.67 cm x 26.67 cm) on the right side of the rectangle to make a Flying Geese Unit (10 ½ in x 20 ½ in / 26.67 cm x 52.07 cm). Make eight. ¼ in (6.35 mm)

Dia. D

Draw wrong side

Sew

Cut Flying Geese Unit

Press

5.

Press

10 ½ in x 20 ½ in (26.67 cm x 52.07 cm) Make 8

Place two Flying Geese Units (10 ½ in x 20 ½ in / 26.67 cm x 52.07 cm) as shown in Diagram E. Pin RST, sew and press open to make one FG Border Section (10 ½ in x 40 ½ in / 26.67 cm x 102.87 cm). Make four.

Dia. E

FG Border Section

+

=

10 ½ in x 40 ½ in (26.67 cm x 102.87 cm) Make 4

www.3wishesfabric.com

page 5

6.

Place a Fussy Cut Animal Patch Square (10 ½ in x 10 ½ in / 26.67 cm x 26.67 cm) on each side of a FG Border Section as shown in Diagram F. Note: Check orientation of designs. Pin RST, sew and press to make the FG Top Border (10 ½ in x 60 ½ in / 26.67 cm x 153.67 cm).

Dia. F

+

+

= FG Top Border

10 ½ in x 60 ½ in (26.67 cm x 153.67 cm)

7.

Follow Step 6 and Diagram G to make the FG Bottom Border (10 ½ in x 60 ½ in / 26.67 cm x 153.67 cm).

Dia. G

FG Bottom Border

10 ½ in x 60 ½ in (26.67 cm x 153.67 cm)

8.

Place two Tossed Animals rectangles (4 ½ in x 30 ½ in / 11.43 cm x 77.47 cm) as shown in Diagram H. Pin RST, sew and press open or to one side to make the Tossed Animals Border Section (4 ½ in x 60 ½ in / 11.43 cm x 153.67 cm). Make four.

Dia. H + = Tossed Animals Border Section

4 ½ in x 60 ½ in (11.43 cm x 153.67 cm) Make 4

9.

Place a Veggies square (4 ½ in x 4 ½ in / 11.43 cm x 11.43 cm) on each side of a Tossed Animals Border Section (4 ½ in x 60 ½ in / 11.43 cm x 153.67 cm) as shown in Diagram I. Pin RST, sew and press to make the Tossed Animals Top Border (4 ½ in x 68 ½ in / 11.43 cm x 173.99 cm). Repeat to make the Tossed Animals Bottom Border.

Dia. I +

+ = Tossed Animals Border Section

4 ½ in x 68 ½ in (11.43 cm x 173.99 cm) Make 2

www.3wishesfabric.com

page 6

10. Refer to Diagram J to place the Borders around the Center Section (40 ½ in x 40 ½ in / 102.87 cm x 102.87 cm). Sew each Border RST in the order listed. Pin matching center, seams and ends. Press seams as shown. Measure at each step to ensure the next border will fit. Tip: If one border is a little larger than the border it is being sewn to, pin well to ease the fullness and place the fullness on the bottom while sewing. Finished Quilt Top should measure 68 ½ in x 68 ½ in (173.99 cm x 173.99 cm).

Flying Geese Border Sides: 2 – FG Border Section (10 ½ in x 40 ½ in / 26.67 cm x 102.87 cm) Top and Bottom: FG Top and Bottom Borders (10 ½ in x 60 ½ in /26.67 cm x 153.67 cm) Quilt Top - 60 ½ in x 60 ½ in (153.67 cm x 153.67 cm).

Tossed Animals Border Sides: 2 – Tossed Animals Border Section (4 ½ in x 60 ½ in / 11.43 cm x 153.67 cm) Top and Bottom: 2 – Tossed Animals Top and Bottom Borders (4 ½ in x 68 ½ in / 11.43 cm x 173.99 cm) Quilt Top - 68 ½ in x 68 ½ in (173.99 cm x 173.99 cm).

Dia. J

Quilt Top

+

+

+

+

+

+

+

+

68 ½ in x 68 ½ in (173.99 cm x 173.99 cm)

www.3wishesfabric.com

page 7

Finishing 11. Remove the selvages from the Gingham Backing fabric.

Note: Check orientation of design. Cut two pieces 38 ¼ in x 76 in (97.15 cm x 193.04 cm). Pin the two sections RST and sew along the long edges as shown in Diagram K. Press the seam open or to one side. The Backing should measure 76 in x 76 in (193.04 cm x 193.04 cm).

Dia. K

12. Press finished Quilt Top and Backing. Tape the Backing, wrong side up, to a firm surface. Layer Batting and Quilt Top (right side up). Baste the layers together with safety pins.

Quilt as desired.

13. Once quilting is complete, square up corners and edges, trimming excess Backing and Batting even with the Quilt Top.

38 ¼ in x 76 in (97.15 cm x 193.04 cm)

38 ¼ in x 76 in (97.15 cm x 193.04 cm)

Backing 76 in x 76 in (193.04 cm x 193.04 cm)

14. Binding – Follow Diagram L to make the Tractors Binding. Remove selvages and sew the short ends of the seven 2 ½ in (6.35 cm) x wof strips RST end to end at a 45° angle to make one continuous strip; press seams open. Press one short end ¼ in (6.35 mm) to the wrong side. Fold in half lengthwise with wrong sides together; press. Leaving a 2 in (5.08 cm) tail on the folded end, place cut edges of folded Binding even with the edge of the Quilt Top and sew, mitering the corners. Overlap ends, trim any excess and finish sewing the Binding. Fold Binding over to back and hand stitch.

Dia. L

Stop stitching ¼ in (6.35 mm) from end of quilt

Finished Care Instructions Machine wash in cold water; gentle cycle. Do not bleach. Tip: Before drying, check for fabric dyes that may have run. If fabric dyes run, rewash and rinse using a color catcher to absorb loose dye. Lay flat to dry or tumble dry low.

www.3wishesfabric.com

©2022 3 Wishes Fabric®

page 8

www.3wishesfabric.com

Follow us here to see more exciting projects and ideas!

Quilt

Featuring the World of Wonder Collection by Josephine Wall Shipping to stores January 2022

Finished Size: 46 ½ in x 54 ½ in (118.11 cm x 138.43 cm)

Fabric Needed 3 Wishes Fabric ® World of Wonder

by Josephine Wall - 1 Panel – Panel (18689-PNL-CTN-D) - 3⁄4 yard – Floral (18685-GRN-CTN-D) - 5⁄8 yard – Unicorn (18686-LIL-CTN-D) - 1⁄2 yard – Strands (18690-MLT-CTN-D) - 1⁄2 yard – Wings (18691-MLT-CTN-D) for Binding - 1⁄3 yard – Lion (18683-GLD-CTN-D) - 2 3⁄4 yards – Bubbles (18687-BLU-CTN-D) for Backing

Additional Supplies Needed: • 55 in x 63 in (139.7 cm x 160.02 cm) Cotton batting • Piecing and sewing thread • Quilting and sewing supplies • Even-feed foot (optional for quilting)

page 1

Before You Begin Read all instructions before beginning project. Do not pre-wash fabrics. Press fabrics with a dry iron on cotton setting before cutting.

Use a ¼" (6.35 mm) seam allowance and sew fabrics with right sides together (RST) unless otherwise noted. Press seams in the direction of the arrows. wof = width of fabric Note: A printed panel may become slightly skewed during the finishing process. Check if panel is square before cutting by folding the panel so selvages meet. If all edges do not meet, pull firmly from corner to corner until the edges meet. Continue until all corners are square.

Cutting Use a rotary cutter and ruler to cut the size and number of squares and rectangles from each fabric listed below.

2 ½ in x 30 ½ in

32 ½ in x 40 ½ in

2 ½ in x 22 ½ in

2½ in

3 in

Unicorn (18686-LIL-CTN-D) - 5⁄8 yard Cut 2 - 2 ½ in x 30 ½ in (6.35 cm x 77.47 cm) Cut 2 - 2 ½ in x 22 ½ in (6.35 cm x 57.15 cm) Cut 24 - 2 ½ in x 2 ½ in (6.35 cm x 6.35 cm) Cut 8 - 3 in x 3 in (7.62 cm x 7.62 cm) - Makes 16 Half-Square Triangles

2 ½ in x 6 ½ in

Panel (18689-PNL-CTN-D) - 1 panel Fussy Cut 1 - 32 ½ in x 40 ½ in (82.55 cm x 102.87 cm) 2 ½ in x 30 ½ in

2 ½ in x 22 ½ in

2½ in

3 in

Strands (18690-MLT-CTN-D) - 1⁄2 yard Cut 16 - 2 ½ in x 6 ½ in (6.35 cm x 16.51 cm) Cut 16 - 2 ½ in x 2 ½ in (6.35 cm x 6.35 cm) Cut 8 - 3 in x 3 in (7.62 cm x 7.62 cm) - Makes 16 Half-Square Triangles

Floral (18685-GRN-CTN-D) - 3⁄4 yard Cut 4 - 2 ½ in x 30 ½ in (6.35 cm x 77.47 cm) Cut 4 - 2 ½ in x 22 ½ in (6.35 cm x 57.15 cm)

www.3wishesfabric.com

page 2

1 ½ in x 40 ½ in

2 ½ in x wof

1 ½ in x 34 ½ in

2½ in

Wings (18691-MLT-CTN-D) - 1⁄2 yard Cut 6 - 2 ½ in (6.35 cm) x wof

2½ in

2½ in

2½ in

Lion (18683-GLD-CTN-D) - 1⁄3 yard Cut 2 - 1 ½ in x 40 ½ in (3.81 cm x 102.87 cm) Cut 2 - 1 ½ in x 34 ½ in (3.81 cm x 87.63 cm) Fussy Cut 4 Lion Heads - 2 ½ in x 2 ½ in (6.35 cm x 6.35 cm)

Sewing 1.

Draw a diagonal line on the wrong side of a Unicorn square 3 in x 3 in (7.62 cm x 7.62 cm) as shown in Diagram A. Place on top of a Strands square 3 in x 3 in (7.62 cm x 7.62 cm) RST and sew ¼ in (6.35 mm) away from the line on both sides. Cut on the drawn line; press. Two squares yield two Half-Square Triangle Units. Repeat to make a total of 16 Half-Square Triangle Units 2 ½ in x 2 ½ in (6.35 cm x 6.35 cm). Trim if necessary.

Dia. A

1⁄4 in (6.35 mm)

Draw Wrong side

2.

Half-Square Triangle Units

Sew

Cut

Press Square up to 2 ½ in x 2 ½ in (6.35 cm x 6.35 cm) Make 16

Place one Lion, four Unicorn squares, and four Half-Square Triangle Units 2 ½ in x 2 ½ in (6.35 cm x 6.35 cm) in three rows as shown in Diagram B. Pin the pieces in each row RST, sew and press. Pin the rows RST matching seams, sew and press to make a Friendship Star Block 6 ½ in x 6 ½ in (16.51 cm x 16.51 cm). Make four.

Dia. B

+

Row 1

Friendship Star Block

+ +

Row 2

+

+

Row 3

+

+

=

= +

3.

6 ½ in x 6 ½ in (16.51 cm x 16.51 cm) Make 4

Place a Strands square 2 ½ in x 2 ½ in (6.35 cm x 6.35 cm) on each side of a Unicorn square 2 ½ in x 2 ½ in (6.35 cm x 6.35 cm) as shown in Diagram C. Note: Check the direction of the design. Pin RST, sew and press. Place a Strands rectangle 2 ½ in x 6 ½ in (6.35 cm x 16.51 cm) on the top and bottom. Pin RST, sew and press to make the Square-in-a-Square Block finishing at 6 ½ in x 6 ½ in (16.51 cm x 16.51 cm). Make eight.

Square-in-a-Square Block

Dia. C + +

=

+

= + 6 ½ in x 6 ½ in (16.51 cm x 16.51 cm) Make 8

4.

Place a Floral rectangle 2 ½ in x 22 ½ in (6.35 cm x 57.15 cm) on each side of a Unicorn rectangle 2 ½ in x 22 ½ in (6.35 cm x 57.15 cm) as shown in Diagram D. Pin RST, sew and press to make Border Unit A finishing at 6 ½ in x 22 ½ in (16.51 cm x 57.15 cm). Repeat to make two.

Border Unit A

Dia. D + = +

6 ½ in x 22 ½ in (16.51 cm x 57.15 cm) Make 2

www.3wishesfabric.com

page 3

5.

Place a Floral rectangle 2 ½ in x 30 ½ in (6.35 cm x 77.47 cm) on each side of a Unicorn rectangle 2 ½ in x 30 ½ in (6.35 cm x 77.47 cm) as shown in Diagram E. Pin RST, sew and press to make Border Unit B finishing at 6 ½ in x 30 ½ in (16.51 cm x 77.47 cm). Make two.

Border Unit B

Dia. E + = +

6 ½ in x 30 ½ in (16.51 cm x 77.47 cm) Make 2

6.

Place a Friendship Star Block and a Square-in-a-Square Block 6 ½ in x 6 ½ in (16.51 cm x 16.51 cm) on each end of Border Unit A 6 ½ in x 22 ½ in (16.51 cm x 57.15 cm) as shown in Diagram F, aligning the seams as shown. Pin, sew and press to make the Top Border finishing at 6 ½ in x 46 ½ in (16.51 cm x 118.11 cm). Repeat to make the Bottom Border.

Dia. F +

+

+

+

Top & Bottom Borders

6 ½ in x 46 ½ in (16.51 cm x 118.11 cm) Make 2

7.

Place a Square-in-a-Square Block 6 ½ in x 6 ½ in (16.51 cm x 16.51 cm) on each end of a Border Unit B 6 ½ in x 30 ½ in (16.51 cm x 77.47 cm) as shown in Diagram G, aligning the seams as shown. Pin, sew and press to make the Side Border 6 ½ in x 42 ½ in (16.51 cm x 107.95 cm). Repeat to make two.

Dia. G +

+ + Side Borders

6 ½ in x 42 ½ in (16.51 cm x 107.95 cm) Make 2

www.3wishesfabric.com

page 4

8.

Refer to Diagram H to finish the Quilt Top. Place a Lion strip 1 ½ in x 40 ½ in (3.81 cm x 102.87 cm) on each side of the Fussy Cut Panel rectangle 32 ½ in x 40 ½ in (82.55 cm x 102.87 cm). Pin RST matching ends and middles; sew and press. Place a Lion strip 1 ½ in x 34 ½ in (3.81 cm x 87.63 cm) on the top and bottom. Pin RST matching ends and middles, sew and press to measure 34 ½ in x 41 ½ in (87.63 cm x 105.41 cm). Note: Check orientation of designs.

Place Side Borders 6 ½ in x 42 ½ in (16.51 cm x 107.95 cm) as shown. Pin RST; sew and press. Place Top and Bottom Borders 6 ½ in x 46 ½ in (16.51 cm x 118.11 cm) as shown on the top and bottom. Pin RST; sew and press. Note: Check orientation of designs.

The Quilt Top should measure 46 ½ in x 54 ½ in (118.11 cm x 138.43 cm).

Quilt Top

Dia. H

+ +

+

+

+

+

+ +

46 ½ in x 54 ½ in (118.11 cm x 138.43 cm)

www.3wishesfabric.com

page 5

Finishing 9.

Remove the selvages from the Bubbles Backing fabric. Note: Check orientation of design. Cut one piece 40 1⁄4 in x 63 in (102.24 cm x 160.02 cm) and two pieces 15 1⁄4 in x 31 ¾ in (38.74 cm x 80.65 cm). Pin RST and sew the two smaller pieces on the short edges; press. Pin the two sections RST and sew along the long edges as shown in Diagram I. Press the seam open or to one side.

The Backing should measure 55 in x 63 in (139.7 cm x 160.02 cm).

Backing

Dia. I

15 1⁄4 in x 31 3⁄4 in

40 1⁄4 in x 63 in

15 1⁄4 in x 31 3⁄4 in

55 in x 63 in (139.7 cm x 160.02 cm)

Bubbles - 2 3⁄4 yard Cut 1 - 40 1⁄4 in x 63 in (102.24 cm x 160.02 cm) Cut 2 - 15 1⁄4 in x 31 3⁄4 in (38.74 cm x 80.65 cm)

10. Press finished Quilt Top and Backing. Tape the Backing, wrong side up, to a firm surface. Layer Batting and Quilt Top (right side up).

Baste the layers together with safety pins. Quilt as desired.

11. Once quilting is complete, square up corners and edges, trimming excess Backing and Batting even with the Quilt Top. 12. Binding – Follow Diagram J to make the Binding from the Wings print. Remove selvages and sew the short ends of the five 2 ½ in x wof (6.35 cm x wof) strips RST end to end at a 45˚ angle to make one continuous strip; press seams open. Press one short end ¼ in (6.35 mm) to the wrong side. Fold in half lengthwise with wrong sides together; press. Leaving a 2 in (5.08 cm) tail on the folded end, place cut edges of folded Binding even with the edge of the Quilt Top and sew, mitering the corners. Overlap ends, trim any excess and finish sewing the Binding. Fold Binding over to back and hand stitch.

Dia. J

Finished Care Instructions Machine wash in cold water; gentle cycle. Do not bleach. Tip: Before drying, check for fabric dyes that may have run. If fabric dyes run, rewash and rinse using a color catcher to absorb loose dye. Lay flat to dry or tumble dry low.

www.3wishesfabric.com

page 6

www.3wishesfabric.com

Follow us here to see more exciting projects and ideas!

Apron

Featuring the Welcome to the Funny Farm Collection

by Connie Haley Shipping to stores January 2022

Finished Size: 31 3⁄4 in x 27 in (80.65 cm x 68.58 cm)

Fabric Needed 3 Wishes Fabric® Welcome to the Funny Farm Collection • 1 Panel – Farm Squad Panel (18727-PNL-CTN-D) • 1⁄2 yard – Tossed Animals (18728-TRQ-CTN-D) • 1⁄4 yard – Hens (18733-WHT-CTN-D) • 1⁄4 yard – Animal Patch (18731-MLT-CTN-D)

Additional Supplies Needed: • Coordinating thread • Basic Sewing Supplies • Sewing machine • Iron and pressing surface

page 1

Before You Begin Read all instructions before beginning project. Do not pre-wash fabrics. Press fabrics with a dry iron on cotton setting before cutting.

Sew fabrics with right sides together (RST) unless otherwise noted. Backstitch at the beginning and end of stitching. Seam allowances can be finished using zigzag or serge stitching. Press seams in the direction of arrows.

Note: A printed panel may become slightly skewed during the finishing process. Check if panel is square before cutting by folding the panel so selvages meet. If all edges do not meet, pull firmly from corner to corner until the edges meet. Continue until all corners are square.

Cutting 20 3⁄4 in x 27 1⁄2 in

10 in Farm Squad Panel (18727-PNL-CTN-D) 1 Panel Fussy Cut 1 - 20 3⁄4 in x 27 1⁄2 in (52.71 cm x 69.85 cm) Apron Body

3 1⁄2 in x 31 1⁄2 in

3 1⁄2 in x 26 in

2 1⁄4 in x 15 in Tossed Animals (18728-TRQ-CTN-D) 1⁄2 yard Cut 2 - 3 1⁄2 in x 31 1⁄2 in (8.89 cm x 80.01 cm) Waist Ties Cut 2 - 3 1⁄2 in x 26 in (8.89 cm x 66.04 cm) Neck Ties Cut 1 - 2 1⁄4 in x 15 in (5.72 cm x 38.1 cm) Apron Top Band

6 1⁄2 in x 17 3⁄4 in

Hens (18733-WHT-CTN-D) 1⁄4 yard Fussy Cut 1 - 6 1⁄2 in x 17 3⁄4 in (16.51 cm x 45.1 cm) Apron Bodice

4 3⁄4 in x 28 in

Animal Patch (18731-MLT-CTN-D) 1⁄4 yard Fussy Cut 1 - 4 3⁄4 in x 28 in (12.07 cm x 71.12 cm) Bottom Band

www.3wishesfabric.com

page 2

Sewing 1. To make the Apron body, measure 1 1⁄4 in (3.18 cm) from the top left and top right corners of the 20 3⁄4 in x 27 1⁄2 in (52.71 cm x 69.85 cm) panel and make a mark. Measure a straight line from the top left mark to the bottom left corner and cut along that line. Repeat for the right side. Align the Apron Body Corner Template with each top corner, trace and cut (Dia. A).

Dia. A 1 1⁄4 in (3.18 cm)

1 1⁄4 in (3.18 cm)

20 3⁄4 in x 27 1⁄2 in (52.71 cm x 69.85 cm) Apron Body

2. To make the Apron bodice, align the Apron Bodice Corner Template with each top corner of the Hens 6 1/2 in x 17 3⁄4 in (16.51 cm x 45.09 cm), trace and cut (Dia. B).

Dia. B

3. Pin the Apron Top Band to the top edge of the Apron Top RST with edges even; sew using a ¼ in (6.35 mm) seam allowance (Dia. C).

Dia. C

Apron Top +

1⁄4 in (6.35 mm) seam allowance

Top Band Wrong side Top Band Wrong side Apron Bodice Right side

Apron Bodice Wrong side

4. Mark the center of the top edge of the Apron Body and the bottom edge of the Apron Top. Pin the Apron Top to the top edge of the Apron Body RST with centers matching and edges even; sew using a ¼ in (6.35 mm) seam allowance (Dia. D).

Dia. D 1⁄4 in (6.35 mm) seam allowance

Match centers

Apron Top & Body

Apron Top Wrong side

Apron Body Right side

www.3wishesfabric.com

page 3

5. Pin the Bottom Band to the bottom edge of the Apron Body RST with edges even; sew using a ¼ in (6.35 mm) seam allowance; press and trim side edges (Dia. E).

Apron

Dia. E

Apron Top & Body Right side

Bottom Band Wrong side

1⁄4 in (6.35 mm) seam allowance

Match centers

6. Along the side edges of the Apron, press only the curved edges ¼ in (6.35 mm) to the wrong side, then press again ¼ in (6.35 mm) to the wrong side. Sew close to the inner fold to hem the edge (Dia. F).

Dia. F

Press curved edges ¼ in (6.35 mm) to wrong side twice

7. Press one short end of a Neck Tie ¼ in (6.35 mm) to the wrong side. Fold long edges wrong sides together so they meet; press to create a crease. Open and fold each long edge ¼ in (6.35 mm) to the wrong side; press. Fold again so edges meet and press.

Topstitch close to each folded edge (Dia. G). Repeat to make all Apron Neck and Waist Ties.

Dia. G

Press short edge ¼ in (6.35 mm) Wrong side

www.3wishesfabric.com

Press long edges ¼ in (6.35 mm)

Wrong side

Crease

Fold & topstitch

Leave cut edge open

page 4

8. On the right side of the Apron, pin the cut end of a Waist Tie to each side edge directly next to the hemmed edge.

Sew ¼ in (6.35 mm) from the edge to attach (Dia. H).

Dia. H

Sew ¼ in (6.35 mm)

Sew ¼ in (6.35 mm)

9. Press the side edges ¼ in (6.35 mm) to the wrong side, then again ¼ in (6.35 mm) to the wrong side; pin. Sew close to the folded edge to hem the sides.

10. On the right side of the Apron, at the top edge measure 1 in from each side and pin the cut end of a Neck Tie. Sew ¼ in (6.35 mm) from the edge to attach. Press the top edge ¼ in (6.35 mm) to the wrong side, then again ¼ in (6.35 mm) to the wrong side; pin.

Sew close to the folded edge to hem (Dia. I).

Dia. I 1 in (2.54 cm)

Front

1 in (2.54 cm) Press top edge ¼ in (6.35 mm) to the wrong side twice

Wrong side

Sew close to the inner fold

Wrong side

Finishing 11. Press the bottom edge ¼ in (6.35 mm) to the wrong side, then again ¼ in (6.35 mm) to the wrong side; pin. Sew close to the inner folded edge to hem the bottom.

Finished Care Instructions Machine wash in cold water; gentle cycle. Do not bleach. Hang to dry.

www.3wishesfabric.com

page 5

Appliqué Template (100% Scale)

Scale: 1 square = 1" x 1"

Cut out each template. Place on fabric, trace and cut according to the instructions.

4 3⁄16 in (10.64 cm)

1 3⁄8 in (3.5 cm)

Align with Top

Align with Top

Apron Body Corner Template Trace1 - Left corner

Apron Bodice Corner Template

Trace1 Reversed - Right corner 3 5⁄16 in (8.41 cm)

Trace1 Left corner 6 1⁄2 in (16.51 cm)

www.3wishesfabric.com

Trace1 Reversed Right corner

page 6

www.3wishesfabric.com

Follow us here to see more exciting projects and ideas!

Barn Quilt Featuring the Welcome to the Funny Farm Collection

by Connie Haley Shipping to stores January 2022

Finished Size: 52 3⁄4 in x 58 3⁄4 in (133.99 cm x 149.23 cm)

Fabric Needed 3 Wishes Fabric® Welcome to the Funny Farm Collection • 1 Panel – Barn Scene Panel (18729-PNL-CTN-D) • 7⁄8 yard – Gingham (18730-RED-CTN-D) for Piecing and Binding • 3⁄4 yard – Carrots (18734-MLT-CTN-D) • 1⁄2 yard – Tossed Animals (18728-TRQ-CTN-D) • 1⁄2 yard – Veggies (18732-MLT-CTN-D) • 1⁄2 yard – Hens (18733-WHT-CTN-D) • 1⁄2 yard – Tractors (18735-RED-CTN-D) • 2 7⁄8 yards – Hens (18733-WHT-CTN-D) for Backing

Additional Supplies Needed: • 61 in x 67 in (154.94 cm x 170.18 cm) Cotton batting • Piecing and sewing thread • Quilting and sewing supplies • Even-feed foot (optional for quilting)

page 1

Before You Begin Read all instructions before beginning project. Do not pre-wash fabrics. Press fabrics with a dry iron on cotton setting before cutting. Use a ¼ in (6.35 mm) seam allowance and sew fabrics with right sides together (RST) unless otherwise noted. Press seams in the direction of the arrows. wof = width of fabric Note: A printed panel may become slightly skewed during the finishing process. Check if panel is square before cutting by folding the panel so selvages meet. If all edges do not meet, pull firmly from corner to corner until the edges meet. Continue until all corners are square.

Cutting Use a rotary cutter and ruler to cut the size and number of squares and rectangles from each fabric listed below.

32 ½ in x 38 ½ in

2 ½ in x 29 ½ in

2 ½ in x 24 ½ in

Carrots (18734-MLT-CTN-D) 3⁄4 yard Cut 4 - 2 ½ in x 29 ½ in (6.35 cm x 74.93 cm) Cut 4 - 2 ½ in x 24 ½ in (6.35 cm x 62.23 cm)

3 ½ in x 16 in

Barn Scene Panel (18729-PNL-CTN-D) 1 Panel Fussy Cut 1 - 32 ½ in x 38 ½ in (82.55 cm x 97.79 cm)

2 ½ in x wof Tossed Animals (18728-TRQ-CTN-D) 1⁄2 yard Cut 7 - 3 ½ in x 16 in (8.89 cm x 40.64 cm)

3 ½ in x 16 in 2 ½ in x 38 ½ in

2 ½ in x 36 ½ in

Gingham (18730-RED-CTN-D) 7⁄8 yard Cut 6 - 2 ½ in (6.35 cm) x wof Cut 2 - 2 ½ in x 38 ½ in (6.35 cm x 97.79 cm) Cut 2 - 2 ½ in x 36 ½ in (6.35 cm x 92.71 cm)

www.3wishesfabric.com

Veggies (18732-MLT-CTN-D) 1⁄2 yard Cut 8 - 3 ½ in x 16 in (8.89 cm x 40.64 cm)

page 2

3 ½ in x 16 in

3 ½ in x 16 in

Hens (18733-WHT-CTN-D) 1⁄2 yard Cut 7 - 3 ½ in x 16 in (8.89 cm x 40.64 cm)

Tractors (18735-RED-CTN-D) 1⁄2 yard Cut 8 - 3 ½ in x 16 in (8.89 cm x 40.64 cm)

Sewing 1. Place a Gingham strip 2 ½ in x 38 ½ in (6.35 cm x 97.79 cm) on each side of the Fussy Cut Barn Scene Panel rectangle 32 ½ in x 38 ½ in (82.55 cm x 97.79 cm). Pin RST matching ends and centers, sew and press. Place a Gingham strip 2 ½ in x 36 ½ in (6.35 cm x 92.71 cm) on the top and bottom. Pin RST matching ends and centers, sew and press. The Center Unit should measure 36 ½ in x 42 ½ in (92.71 cm x 107.95 cm).

Dia. A Center Unit +

+

+

=

+ 36 ½ in x 42 ½ in (92.71 cm x 107.95 cm)

2. Alternate seven Hens rectangles 3 ½ in x 16 in (8.89 cm x 40.64 cm) with seven Tossed Animal rectangles 3 ½ in x 16 in (8.89 cm x 40.64 cm) as shown in Diagram B. Pin RST, sew and press. The strip set should measure 16 in x 42 ½ in (40.64 cm x 107.95 cm).

Strip Set

Dia. B

+

+

+

+

+

+

+

+

+

+

+

+

+

=

16 in x 42 ½ in (40.64 cm x 107.95 cm)

www.3wishesfabric.com

page 3

3. Refer to Diagram C to straighten (trim) one side of the Strip Set and cut into four Hens/Tossed Animal Borders 3 ½ in x 42 ½ in (8.89 cm x 107.95 cm).

Dia. C

Strip Set

3 ½ in (8.89 cm) 3 ½ in (8.89 cm) 3 ½ in (8.89 cm) 3 ½ in (8.89 cm) Trim Hens/Tossed Animals Border

3 ½ in x 42 ½ in (40.64 cm x 107.95 cm) Make 4

3. Follow Step 2 and Diagram D to alternate eight Veggies rectangles 3 ½ in x 16 in (8.89 cm x 40.64 cm) with eight Tractors rectangles 3 ½ in x 16 in (8.89 cm x 40.64 cm) to make four Veggies/Tractors Borders 3 ½ in x 48 ½ in (8.89 cm x 123.19 cm). Note: Check orientation of designs.

Dia. D

Veggies/Tractors Border

3 ½ in x 48 ½ in (40.64 cm x 123.19 cm) Make 4

4. Place two Carrots rectangles 2 ½ in x 24 ½ in (6.35 cm x 62.23 cm) as shown in Diagram E. Note: Check orientation of designs. Pin RST, sew and press open or to one side to make the Carrots Top Border 2 ½ in x 48 ½ in (6.35 cm x 123.19 cm). Repeat to make the Carrots Bottom Border.

Dia. E +

=

Carrots Top and Bottom Borders

2 ½ in x 48 ½ in (6.35 cm x 123.19 cm) Make 2

5. Place two Carrots rectangles 2 ½ in x 29 ½ in (6.35 cm x 74.93 cm) as shown in Diagram F. Pin RST, sew and press open or to one side to make the Carrots Side Border 2 ½ in x 58 ½ in (6.35 cm x 148.59 cm). Make 2.

Dia. F +

=

Carrots Side Borders

2 ½ in x 58 ½ in (6.35 cm x 148.59 cm) Make 2

www.3wishesfabric.com

page 4

6. Refer to Diagram G to place the Borders around the Center Unit 36 ½ in x 42 ½ in (92.71 cm x 107.95 cm). Sew each Border RST in the order listed. Pin matching center, seams and ends. Note: Check orientation of designs. Press seams as shown. Measure at each step to ensure the next border will fit. Tip: If one border is a little larger than the border it is being sewn to, pin well to ease the fullness and place the fullness on the bottom while sewing. Finished Quilt Top should measure 52 ½ in x 58 ½ in (133.35 cm x 148.59 cm).

Hens/Tossed Animals Border (2) Sides: Made in Step 3 - 3 ½ in x 42 ½ in (8.89 cm x 107.95 cm) (2) Top and Bottom: Made in Step 3 - 3 ½ in x 42 ½ in (8.89 cm x 107.95 cm) Quilt Top: 42 ½ in x 48 ½ in (107.95 cm x 123.19 cm) Veggies/Tractor Border (2) Sides: Made in Step 3 - 3 ½ in x 48 ½ in (8.89 cm x 123.19 cm) (2) Top and Bottom: Made in Step 3 3 ½ in x 48 ½ in (8.89 cm x 123.19 cm) Quilt Top: 48 ½ in x 54 ½ in (123.19 cm x 138.43 cm) Carrots Border (2) Top and Bottom: Made in Step 4 - 2 ½ in x 48 ½ in (6.35 cm x 123.19 cm) (2) Sides: Made in Step 5 - 2 ½ in x 58 ½ in (6.35 cm x 148.59 cm) Quilt Top - 52 ½ in x 58 ½ in (133.35 cm x 148.59 cm) Welcome to the Funny Farm Barn Scene Quilt Top

Dia. G

+

+

+

+

+

+

+

+

+

+

+

+ 52 ½ in x 58 ½ in (133.35 cm x 148.59 cm)

www.3wishesfabric.com

page 5

Finishing 18. Remove the selvages from the Hens Backing fabric. Cut one piece 40 ¼ in x 67 in (102.24 cm x 170.18 cm) and two pieces 21 ¼ in x 33 3⁄4 in (53.98 cm x 85.73 cm). Pin RST and sew the two smaller pieces on the short edges; press. Pin the two sections RST along the long edges as shown in Diagram H. The Backing should measure 61 in x 67 in (154.94 cm x 170.18 cm).

Backing

Dia. H

21 1⁄4 in x 33 3⁄4 in

40 1⁄4 in x 67 in

21 1⁄4 in x 33 3⁄4 in

61 in x 67 in (154.94 cm x 170.18 cm)

19. Press finished Quilt Top and Backing. Tape the Backing, wrong side up, to a firm surface. Layer Batting and Quilt Top (right side up).

Baste the layers together with safety pins. Quilt as desired.

20. Once quilting is complete, square up corners and edges, trimming excess Backing and Batting even with the Quilt Top. 21. Follow Diagram I to make the Gingham Binding. Remove selvages and sew the short ends of the six 2 ½ in (6.35 cm) x wof strips RST end to end at a 45° angle to make one continuous strip; press seams open. Press one short end ¼ in (6.35 mm) to the wrong side.

Fold in half lengthwise with wrong sides together; press. Leaving a 2 in (5.08 cm) tail on the folded end, place cut edges of folded Binding even with the edge of the Quilt Top and sew, mitering the corners. Overlap ends, trim any excess and finish sewing the Binding. Fold Binding over to back and hand stitch.

Dia. I

Finished Care Instructions Machine wash in cold water; gentle cycle. Do not bleach. Tip: Before drying, check for fabric dyes that may have run. If fabric dyes run, rewash and rinse using a color catcher to absorb loose dye. Lay flat to dry or tumble dry low.

www.3wishesfabric.com

©2022 3 Wishes Fabric®

page 6

www.3wishesfabric.com

Follow us here to see more exciting projects and ideas!

Placemats Featuring the Welcome to the Funny Farm Collection

by Connie Haley and the Good Vibes Collection

by Courtney Morgenstern Shipping to stores January 2022

Finished Size: (4) 15 3⁄4 in x 19 3⁄4 in (40 cm x 50.17 cm)

Fabric Needed 3 Wishes Fabric® Welcome to the Funny Farm Collection • 1 Panel – Barn Scene Panel (18729-PNL-CTN-D) • 1 yd – Veggies (18732-MLT-CTN-D) - Placemat Backs • 3⁄4 yd – Tossed Animals (18728-TRQ-CTN-D) • 3⁄8 yd – Gingham (18730-RED-CTN-D) • 3⁄8 yd – Tractors (18735-RED-CTN-D) • 1⁄4 yd – Carrots (18734-MLT-CTN-D)

Additional Supplies Needed: • (4) 16 1⁄2 in x 20 1⁄2 in (41.91 cm x 52.07 cm) Batting • Coordinating thread • Quilting and sewing supplies • Sewing machine • Iron and pressing surface

3 Wishes Fabric® Good Vibes Collection • 1⁄4 yd – Circle Dots (18660-WOW-CTN-D)

page 1

Before You Begin Read all instructions before beginning project. Do not pre-wash fabrics. Press fabrics with a dry iron on cotton setting before cutting.

Sew fabrics with right sides together (RST) unless otherwise noted. Backstitch at the beginning and end of stitching. Press seams in the direction of arrows.

Note: A printed panel may become slightly skewed during the finishing process. Check if panel is square before cutting by folding the panel so selvages meet. If all edges do not meet, pull firmly from corner to corner until the edges meet. Continue until all corners are square.

Cutting Use a rotary cutter and ruler to cut the size and number of squares and rectangles from each fabric listed below.

16 1⁄2 in x 20 1⁄2 in

8 1⁄2 in x 8 1⁄2 in 8 1⁄2 in x 8 1⁄2 in

8 1⁄2 in x 8 1⁄2 in 8 1⁄2 in x 8 1⁄2 in

Veggies (18732-MLT-CTN-D) 1 yard Cut 4 - 16 1⁄2 in x 20 1⁄2 in (41.91 cm x 52.07 cm) - Placemat Backs 1 1⁄2 in x 10 1⁄2 in

Barn Scene Panel (18729-PNL-CTN-D) 1 Panel Fussy Cut 4 - 8 1⁄2 in x 8 1⁄2 in (21.59 cm x 21.59 cm) 4 1⁄2 in x 5 1⁄2 in

4 in x 6 1⁄4 in

2 1⁄2 in x 10 1⁄2 in

3 1⁄2 in x 7 1⁄2 in 4 in x 4 in

Gingham (18730-RED-CTN-D) 3⁄8 yard Cut 8 - 3 1⁄2 in x 7 1⁄2 in (8.89 cm x 19.05 cm) Cut 4 - 1 1⁄2 in x 10 1⁄2 in (3.81 cm x 26.67 cm) 2 1⁄2 in x 20 1⁄2 in

Carrots (18734-MLT-CTN-D) 1⁄4 yard Cut 4 - 2 1⁄2 in x 20 1⁄2 in (6.35 cm x 52.07 cm) Tossed Animals (18728-TRQ-CTN-D) 3⁄4 yard Cut 8 - 4 1⁄2 in x 5 1⁄2 in (11.43 cm x 13.97 cm) Cut 4 - 4 in x 6 1⁄4 in (10.16 cm x 15.88 cm) Cut 8 - 2 1⁄2 in x 10 1⁄2 in (6.35 cm x 26.67 cm) Cut 4 - 4 in x 4 in (10.16 cm x 10.16 cm)

www.3wishesfabric.com

page 2

1 1⁄2 in x 8 1⁄2 in

4 in x 6 1⁄4 in

1 1⁄2 in x 10 1⁄2 in

4 in x 4 in

Circle Dots from the 3W Good Vibes Collection (18660-WOW-CTN-D) 1⁄4 yard Cut 8 - 1 1⁄2 in x 8 1⁄2 in (3.81 cm x 21.59 cm) Cut 8 - 1 1⁄2 in x 10 1⁄2 in (3.81 cm x 26.67 cm) Tractors (18735-RED-CTN-D) 3⁄8 yard Cut 4 - 4 in x 6 1⁄4 in (10.16 cm x 15.88 cm) Cut 4 - 4 in x 4 in (10.16 cm x 10.16 cm)

Sewing 1. Pin a Circle Dots strip 1 ½ in x 8 ½ in (3.81 cm x 21.59 cm) on each side of the Lamb Center block RST matching ends, sew and press as shown in Diagram A. Pin a Circle Dots strip 1 ½ in x 10 ½ in (3.81 cm x 26.67 cm) RST on the top and bottom, sew and press to make the Placemat Center Unit (10½ in x 10 ½ in). Repeat to make the Cow, Goat and Pig Center Units.

Placemat Center Unit

Dia. A +

+

+

=

+ 10 1⁄2 in x 10 1⁄2 in (26.67 cm x 26.67 cm)

2. Refer to Diagram B to make the Half-Rectangle Triangle (HRT) Units. Note: Two rectangles yield two matching HRT Units. Draw a diagonal line on the wrong side of a Tractors rectangle 4 in x 6 1⁄4 in (10.16 cm x 15.88 cm) from the lower left corner to the upper right corner. Place the Tractors rectangle on top of a Tossed Animals rectangle 4 in x 6 1⁄4 in (10.16 cm x 15.88 cm) with RST and sew ¼ in (6.35mm) away from the line on both sides. Cut on the drawn line; press. Square up to 3 ½ in x 5 ½ in (8.89 cm x 13.97 cm) and trim if necessary. Repeat to make a total of four HRT Right Units.

Repeat except draw the diagonal line the opposite way; from the upper left corner to the lower right corner. Make a total of 4 HRT Left Units 3 ½ in x 5 ½ in (8.89 cm x 13.97 cm).

Dia. B

1⁄4 in (6.35 cm)

HRT Right Unit

Make 4 Draw Wrong side

Press Align opposite corners

Sew

Square up to 3 1⁄2 in x 5 1⁄2 in (8.89 cm x 13.97 cm)

Cut

HRT Left Unit

Draw Wrong side

Make 4

3. Refer to Diagram C to pin a Left HRT Unit and a Right HRT Unit 3 ½ in x 5 ½ in (8.89 cm x 13.97 cm) with RST; sew and press. Pin the Gingham strip 1 ½ in x 10 ½ in (3.81 cm x 26.67 cm) to the bottom; sew and press. Pin a Tossed Animals rectangle 4 ½ in x 5 ½ in (11.43 cm x 13.97 cm) to each side; sew and press to create the Top Row. Dia. C HRT Left Unit

HRT Right Unit

Top Row

+

+ +

www.3wishesfabric.com

+ 4 1⁄2 in x 5 1⁄2 in (11.43 cm x 13.97 cm) Make 4

page 3

4. Refer to Diagram D to make the Half-Square Triangle (HST) Units. Note: Two squares yield two HST Units. Draw a diagonal line on the wrong side of a Tractors square 4 in x 4 in (10.16 cm x 10.16 cm). Place the Tractors square on top of a Tossed Animals square 4 in x 4 in (10.16 cm x 10.16 cm) with RST and sew ¼ in (6.35 mm) away from the line on both sides. Cut on the drawn line; press.

Square up and trim if necessary.

1⁄4 in (6.35 cm)

Dia. D

Draw Wrong side

Sew

HST Unit

Cut

Make 8

Press Square up to 3 1⁄2 in x 3 1⁄2 in (8.89 cm x 8.89 cm)

5. Refer to Diagram E to pin and sew a Gingham strip 3 ½ in x 7 ½ in (8.89 cm x 19.05 cm) RST to the bottom of a HST; press. Add a Tossed Animals strip 2 ½ in x 10 ½ in (6.35 cm x 26.67 cm) to the side as shown; sew and press to create a HST Side Unit. Repeat to make a second HST Side Unit that is a mirror image.

Side Unit

Dia. E

Side Unit Mirror

+ +

5 1⁄2 in x 10 1⁄2 in 5 1⁄2 in x 10 1⁄2 in (13.97 cm x 26.67 cm) (13.97 cm x 26.67 cm) Make 4 Make 4

6. To create the middle row, pin a HST Side Unit on each side of the Center Unit RST; sew and press (Dia. F).

Middle Row

Dia. F

+

+

=

20 1⁄2 in x 10 1⁄2 in (52.07 cm x 26.67 cm) Make 4

7. Pin the Placemat Top, Middle and Carrots strip 2 ½ in x 20 ½ in (6.35 cm x 52.07 cm) RST as show in Diagram G; sew and press to complete the Placemat Front.

Dia. G

Placemat Front

+

=

+ 16 1⁄2 in x 20 1⁄2 in (41.91 cm x 52.07 cm) Make 4

www.3wishesfabric.com

page 4

8. Press the finished Placemat Front and Veggies Back 16 ½ in x 20 ½ in (41.91 cm x 52.07 cm). Layer the Front and Back RST on top of the Batting with edges even; pin and sew around the edges leaving a 4 in (10.16 cm) opening in the bottom. Carefully clip corners and turn right side out through the opening (Dia. H).

Dia. H

Wrong side

=

4 in (10.16 cm)

15 3⁄4 in x 19 3⁄4 in (40 cm x 50.17 cm)

9. Press the edges and hand stitch opening closed. Topstitch around the Placemat close to all edges. Quilt around the images and in-the-ditch or as desired.

Finished Care Instructions Machine wash in cold water; gentle cycle. Do not bleach. Lay flat or hang to dry.

www.3wishesfabric.com

page 5