Hino K13DT Valve adjusting procedure, Valve lash clearance specifications, Cylinder Head Parts List, Page 1 of 5
HINO K13DT VALVE ADJUSTING PROCEDURE METHOD FOR DETERMINING IF THE NO.1 PISTON IS AT
THE TOP DEAD CENTER ON COMPRESSION STROKE. NOTE:
1.
2.
Move both the intake and the exhaust rocker arms of the No.1 or No.6 cylinder by hand; if both rocker arms can be moved, the piston is at top dead center on the compression stroke. If the injection timing mark is nearly aligned with the pointer, the No.1 piston is at top dead center on compression stroke.
NOTE:
3.
PUSH RODS: MOVE (COMPRES SION STROKE)
PUSH RODS STANDING (OVERLAP PING STROKE)
o Turn the crankshaft to align the mark "1/6" on the flywheel with the pointer of the flywheel housing. o In this position the No.1 or No.6 piston is at the top dead center on compression stroke. The pointer and mark "1-6" are engraved on some model timing gear cover and on the torsional damper, so use these pointer and marker if so equipped when adjusting the engine.
If not, turn the crankshaft one complete revolution and align the marks as above.
While locking the push rods of No.1 and No.6 pistons, turn the crankshaft counterclockwise and clockwise about 30° to 40° as shown in the figure. If the piston whose exhaust and intake push rods do not move during the interval, it is at the top dead center on compression stroke. If the piston whose push rods have moved, it is at the completion of the exhaust and begun of the intake stroke (overlapping stroke).
NOTE: Always loosen the lock nut and raise the adjusting screws fully to the top. If the adjusting screws are too low, the piston and valves may strike each other during valve clearance adjustment.
SM3-F0263
Hino Diesel Engine Parts contact email: EngineParts@HeavyEquipmentRestorationParts.com Phone: 269 673 1638 Website: www.HeavyEquipmentRestorationParts.com
Hino K13DT Valve adjusting procedure, Valve lash clearance specifications, Cylinder Head Parts List, Page 2 of 5 HINO K13DT VALVE CLEARANCE , VALVE LASH SPECIFICATIONS
[Valve clearance adjusting procedures] BEFORE ADJUSTING 1. 2.
3.
SM3-K0024
Before adjusting, make sure that the heads and the rocker support bolts are tightened with the specified torque. Make sure that there are no foreign matter and dust be tween the cross heads and the valve stems, and between the rocker arms and the cross heads. Set the piston in the particular cylinder to adjust for top dead center on the compression stroke.
ADJUSTING 1.
With the No.1 piston positioned at top dead center on com pression stroke, adjust the No.1 valve clearance using a thickness gauge. The thickness gauge should move with a very slight pull.
Hino K13DT Valve Clearance (When cold): Hino K13DT Intake Valves Hino K13DT Exhaust Valves
Unit: mm {in.}
0.4{0.0157} (K13C-T) 0.4{0.0157} (K13D-T) 0.5{0.0197} (K13C-T) 0.4{0.0157} (K13D-T)
VALVE CLEARANCE 2.
Adjust the other valves. ° Turn the crankshaft counterclockwise 120 viewed from fly wheel side. Adjust the valve clearance for each cylinder in the firing order.
Firing order: 1-4-2-6-3-5 SM3-715
Hino Diesel Engine Parts contact email: EngineParts@HeavyEquipmentRestorationParts.com Phone: 269 673 1638 Website: www.HeavyEquipmentRestorationParts.com
Hino K13DT Valve adjusting procedure, Valve lash clearance specifications, Cylinder Head Parts List, Page 3 of 5
Hino K13D Cylinder Head Parts Hino K13DT Cylinder Head Parts
T: 13-18 {130-190, 10-13}
T: 265-284 {2,700-2,900, 196-209} for 0 16
�
--
3�:;�---·
T: 45-49 {450-500, 33-36} 14
�
{800-900, 58-65} for 0 12
II
2
\
z
1
J�11
13�
/
12
T= 19-26 {190-270, 14-19}
S6-K13-0005
T = K13DT Tightening torque: N-m {kgf-cm, lbf-ft}
1. 2. 3. 4. 5. 6. 7.
Hino K13DT Valve Cover Gasket K13DT Valve Cover K13DT Ventilator K13DT Flange K13DT Valve stem oil seal K13DT Cylinder head bolt K13DT Cylinder head additional bolt
8. 9. 10. 11. 12. 13. 14.
K13DT Cylinder head Hino K13DT Cylinder head gasket K13DT Engine hanger K13DT Straight pin K13DT Intake manifold studs, nuts, K13DT Spacer K13DT Exhaust studs, nuts,
15. 16. 17. 18. 19. 20. 21. 22.
K13DT Injector Seal Gasket K13DT Injector 0-ring K13DT Nozzle holder adapter K13DT Injector Packing ring K13DT Nozzle holder K13DT Nozzle K13DT Nozzle holder gauge Hino K13DT Injector Parts 17-19
Hino Diesel Engine Parts contact email: EngineParts@HeavyEquipmentRestorationParts.com Phone: 269 673 1638 Website: www.HeavyEquipmentRestorationParts.com
Hino K13DT Valve adjusting procedure, Valve lash clearance specifications, Cylinder Head Parts List, Page 4 of 5
Hino K13D Valve Train Parts Hino K13D-T Valve Train Parts
u'
T:148-166 {1,500-1,700, 109-122}
T-40-49 {4-;,0-500, 29-36}
2
'
,_U��,
·-�-"' •'
�ti�,,· :�, ..
·��r=
1
Intake Rocker Arms Exhaust Rocker Arms
Intake Valve Guides Exhaust Valve Guides
'-
�
10 �..rlJ 11 II -d, I'--. @,1�, I : _L) I I
,.L
J
I I
, :]J�" _;_,)
_)
I
I
:
I
I
:
I
:
21
Intake Valves Exhaust Valves
Intake Valve Seats Exhaust Valve Seats S6-K13-0006
T = K13DT Tightening torque., N-m {kgf-cm, lbf,ftl
1. 2 3: 4_ 5. 6. 7_
K13DT Cylinder h_ead K13DT Retainer rmg K13DT Plain washer K13DT Rocker Arm Bushing K13DT Rocker arms K13DT Roeker arm support K13DT vaI ve stem caps
8. 9. 10. 11. 12. 13. 14.
K13DT valve cotters, keepers, K13DT Valve spr�ng . upper seat K13DT Valve Springs K13DT Valve sprmg lower seat . Hino K13DT Intake Valves K13DT Valve clearance adjusting screw K13DT Push rod
15. K13DT Valve lifters, Tappets, 16. K13DT Valve st�m oil seals 17. Hino K13DT Intake Valve guides Hino K13DT Exhaust Valve guides 18. K13DT Pipe 19. K13DT Soft Plug Set 20. Hino K13DT Intake Valve seats 21. Hino K13DT Exhaust Valve seats 22. Hino K13DT Exhaust Valves
Hino Diesel Engine Parts contact email: EngineParts@HeavyEquipmentRestorationParts.com Phone: 269 673 1638 Website: www.HeavyEquipmentRestorationParts.com
Hino K13DT Valve adjusting procedure, Valve lash clearance specifications, Cylinder Head Parts List, Page 5 of 5
Hino K13D K13D-T Exhaust System Parts and Intake System Parts 4
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13.
S6-K13-0069
14. 15. 16. 17. 18. 19.
Hino K13DT Exhaust manifold connector K13DT Exhaust Gaskets K13DT Exhaust Seal rings K13DT Turbocharger K13DT Turbo oil line 0-ring K13DT Turbo Oil inlet pipe K13DT Turbo Oil outlet pipe K13DT Exhaust manifold K13DT Exhaust Seal rings K13DT Heat insulator K13DT Intake Gaskets K13DT Intake manifold K13DT Air intake heater (If so equipped) K13DT Intake pipe K13DT Intake 0-ring K13DT Intake Bracket K13DT Air hose Dust indicator Air cleaner
17
8 11
S6-K13-0068
T = K13DT Tightening torque: N-m {kgf,cm, lbf,ft}
Hino Diesel Engine Parts contact email: EngineParts@HeavyEquipmentRestorationParts.com Phone: 269 673 1638 Website: www.HeavyEquipmentRestorationParts.com