HP 42 available to the rotor HP 50 max to hydraulic motor
HYDRAULIC REACH MOWERS (GEAR HYDRAULIC SYSTEM “HP”) GROUP
A
Junction pipes
Drop forged parts used in the arms Protected pipes
Central pivot
Stiff pipes on rotor feed
Rotation block for transport
“Overlap” spiral rotor with two spiral rows
Drop forged brackets for arms and flail head rotation
Pressurized oil tank
Drop forged parts Floating Reversible rotor by cable
Top mounted flail head with 190° angle
Rear mounted flail head with 235° angle
Power slew 115°
Replaceable skids Adjustable rear roller
new
Cable controls
Electric Proportional Controls with rotor start and stop by electric switch
Frame “DELTA BOX” (forces shared and balanced HP Tractor
60
70
TPE600 Evo
Gear High Performace hydraulic system
90
Min. tractor weight Kg
Min. tractor width m
3200
2,20
Working positions (m) A
m
TPE600 Evo 5,96
B
m
6,18
C
m
3,31
D
m
4,36
E
m
5,54
I
m
2,16
L
m
1,14
M
m
2,55
N
m
2,42
O
m
2,95
P
m
1,42
I
L
B
E
O M
Replaceable skids
80
C P N
D
A
Technical data Model
Max horizontal reach* m
Flail head forward
Weight (•)
Oil
m
Kg
l
Rpm
MAX Rpm
TPE600 Evo
5,96
-
1.050
137
3.100
540
(*) Reach measured from tractor centre line to head edge.
Rotor
Pto
Flail head angle
235°
(•) The weight includes flail head, oil, and oil cooler
Machines with cable controls “Classic” Code PI60LHFDY13ZA
Equipped with:
Model TPE600 Evo with flail head TJ125 m 1,25
Flail Head Cast iron gear pump motor
Machines with electro-hydraulic proportional control “EP-Tronic” Code PI60LHADY13ZA
Oil cooler in Alluminum with thermostat
new
Model TPE600 Evo EP-Tronic with flail head TJ125 m 1,25
Power slew 115° Hydraulic break-back on the rotation with max pressure valves and soft stop.
Completing equipment to the base machine Code TGA5020 TSN5033 OPT001121000 ATT/4 TGA5018
Length cm (640-890) (470-720) (340-460)
TGA5019
(485-720) Top Link long
Mechanic roll-over protection system (SAB)
1 set of standard stabilizers to the tractor. Compulsory option 1 set of bent stabilizers recommended with “Delta yoke” “Delta yoke” for stabilizers Fixed linkage. Stabilizers TGA5020 needed. Top Link short
Rear roller Ø 133 mm “Overlap” spiral rotor with two spiral rows. Rotor balancing on side flanges.
Option Code TSP5026 TPE52002 TSP5022SX/02 TSP5024/02
Reversible rotor cable (DSR) Front and rear abrasion resistant guard for flail head
** Price reduction for Top Mounted TJ head Price reduction for NO OIL COOLER (only CLASSIC) Lift float (LFA mechanic) Lift float (LFA electric) only for Comfort Plus Light kit Electric roll-over protection system (SAB) only for Comfort Plus
Flail head
TJ125
Width (m) Rotor speed (rpm) Blade tip speed (m/sec) Flail head angle Weight (Kg)
1,25 3100 64 190°/235° 240
Replaceable skids Oil and Pto shaft
TJ 125
Direct drive
Flails TJ125 Interchangeable on the same rotor
Interchangeable on the same rotor
Multi-use blades for: grass, shrubs, bushes, sticks, wood Ø max 3 cm
Articulated “Y” flails for: grass and bushes
Bootie blades for: grass, hedges, bushes
Ø max 2 cm
Ø max 2 cm
Spoon blade for: grass, “T” Hammer for shrubs, bushes, sticks, woods wood Ø max 4 cm Ø max 2 cm
Hedge trimming blades for: grass, hedges Ø max 1 cm
Warning Cod. 0901146
Cod. 0901164
Cod. 0901147
Cod. 0901049
Cod. 0901138
Cod. 0901135
n° 52
n° 26
n° 26
n° 60
n° 30
n° 30
FERRI srl - Via Govoni, 30 - 44034 Tamara (FE) Italy - Tel. +39 0532 866866 - Fax +39 0532 866851 - info@ferrisrl.it - www.ferrisrl.it Spare parts: Tel: +39 0532 866993 - Fax: +39 0532 867061 - e-mail: parts@ferrisrl.it After Sales Service: Tel: +39 0532 866991 - Fax: +39 0532 866851 - e-mail: service@ferrisrl.it
IT IS RECOMMENDED that the connection between tractor and shredder and its setting up should be made with the Dealer according the instructions and warnings listed on our Use and Maintenance Manual. For further information please contact our after sales service.