Service Repair Manual
Models
140M 2 MOTOR GRADER
140M Series 2 Motor Grader - All Wheel Drive R9G00001-UP (MACHINE) POWER...
1/21
Shutdown SIS Previous Screen Product: MOTOR GRADER Model: 140M 2 MOTOR GRADER R9G Configuration: 140M Series 2 Motor Grader - All Wheel Drive R9G00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly 12M Series 2, 140M Series 2 and 160M Series 2 Motor Graders Power Train Media Number -KENR8899-03
Publication Date -01/05/2017
Date Updated -18/05/2017
i07506146
Piston Motor (Wheel Propel) - Assemble SMCS - 4351-016-YW; 5058-016-YW
Assembly Procedure Table 1 Required Tools Tool
Part Number
Part Description
Qty
B
317-3804
Spanner Wrench
1
D
1P-0510
Driver Gp
1
E
1P-1862
Pliers
1
F
-
Loctite 276 Thread Locker
1
G
5P-3037
Pusher Plate
1
H
4C-4032
Loctite 609 Retaining Compound
1
J
317-5303
Measuring Plate
1
K
1U-8846
Loctite High Flex GM
1
L
4C-9507
Loctite 620Retaining Compound
1
NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life.
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning fluid. Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/1/6
140M Series 2 Motor Grader - All Wheel Drive R9G00001-UP (MACHINE) POWER...
2/21
replacement. Dirt and other contaminants can damage the precision component. Perform assembly procedures on a clean work surface. Keep components covered and protected always. Note: Check the O-ring seals for wear or for damage. Replace the components, if necessary.
Illustration 1
g01408523
1. Raise the temperature of bearing cone (45). Install bearing cone (45) onto shaft (43).
Illustration 2
g01408574
2. Raise the temperature of race (44). Apply Tooling (H) to shaft (43). Use Tooling (G) and a suitable press to install race (44) onto shaft (43). The tapered end of race (44) should face away from the bearing.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/1/6
140M Series 2 Motor Grader - All Wheel Drive R9G00001-UP (MACHINE) POWER...
Illustration 3
3/21
g01408585
3. Lower the temperature of bearing cup (66). Use Tooling (D) to install bearing cup (66) into housing (35). 4. If necessary, install pins (67) into housing (35). 5. Install cradle bearings (68) into housing (35). Note: Steps 6 through 14 are for determining the proper number of shims (34) (not shown) that will be installed.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/1/6
140M Series 2 Motor Grader - All Wheel Drive R9G00001-UP (MACHINE) POWER...
Illustration 4
4/21
g01408606
6. Install shaft (43) into housing (35). Measure the distance from the shoulder on shaft (43) to the top of housing (35) and record Dimension (A) to the nearest 0.010 mm (0.0004 inch).
Illustration 5
g01408628
7. Measure Dimension (B) and record Dimension (B) to the nearest 0.010 mm (0.0004 inch) on special washer (47).
Illustration 6
g01408635
8. Measure Dimension (C) and record Dimension (C) to the nearest 0.010 mm (0.0004 inch) on bearing cone (46) and bearing cup (33).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/1/6
140M Series 2 Motor Grader - All Wheel Drive R9G00001-UP (MACHINE) POWER...
Illustration 7
5/21
g01408647
9. Measure Dimension (D) and record Dimension (D) to the nearest 0.010 mm (0.0004 inch) on housing (26). Note: Ensure that all existing shims have been removed. 10. Calculate Dimension (X) and record Dimension (X) to the nearest 0.010 mm (0.0004 inch). Note: Dimension (X) is equal to Dimension (A) plus Dimension (D). 11. Calculate Dimension (Y) and record Dimension (Y) to the nearest 0.010 mm (0.0004 inch). Note: Dimension (Y) equals Dimension (B) plus Dimension (C). 12. Calculate Dimension (Z) and record Dimension (Z) to the nearest 0.010 mm (0.0004 inch). Note: Dimension (Z) equals Dimension (X) minus Dimension (Y). 13. The number of shims is equal to the value of Dimension (Z) with a tolerance of + 0.020 mm (+ 0.0008 inch) or − 0.070 mm (− 0.0028 inch).
Illustration 8
g01408691
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/1/6
140M Series 2 Motor Grader - All Wheel Drive R9G00001-UP (MACHINE) POWER...
6/21
14. Use the measurement that was taken in Step 13 to install the proper number of shims (37) (not shown) into housing (26). 15. Lower the temperature of bearing cup (33). Use Tooling (D) to install bearing cup (33) into housing (26). 16. Use Steps 17 through 23 to determine the proper number of shims (53) (not shown) that will be installed.
Illustration 9
g01408860
17. Install washer (52) into barrel (49). Use Tooling (E) to install retaining ring (48). Note: Note the orientation of retaining ring (48) from the Disassembly Procedure.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/1/6
140M Series 2 Motor Grader - All Wheel Drive R9G00001-UP (MACHINE) POWER...
Illustration 10
7/21
g01408867
18. Install barrel (49) into housing (35). Measure Dimension (L) and record Dimension (L) to the nearest 0.010 mm (0.0004 inch).
Illustration 11
g01408880
19. Install port plate (36) onto housing (26). Measure Dimension (M) and record Dimension (M) to the nearest 0.010 mm (0.0004 inch). 20. Calculate Dimension (N) and record Dimension (N). Note: Dimension (N) equals Dimension (L) minus Dimension (M).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/1/6
140M Series 2 Motor Grader - All Wheel Drive R9G00001-UP (MACHINE) POWER...
8/21
21. Select a combination of shims (53) (not shown) that equals Dimension (N) minus 0.090 Âą 0.040 mm (0.0035 Âą 0.0016 inch).
Illustration 12
Illustration 13
g01408860
g01408179
22. Use Tooling (E) to remove retaining ring (48) from barrel (49). Remove washer (52) from barrel (49). 23. Install washer (50), spring (51), washer (52), and the correct number of shims (53) that were determined in Step 21. Note: Be sure that the tapered edge of washer (50) is facing away from spring (51).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/1/6
140M Series 2 Motor Grader - All Wheel Drive R9G00001-UP (MACHINE) POWER...
Illustration 14
g01408159
Improper assembly of parts that are spring loaded can cause bodily injury. To prevent possible injury, follow the established assembly procedure and wear protective equipment.
24. Use Tooling (D) and a suitable press to apply slight compression to barrel assembly (37). Use Tooling (E) to install retaining ring (48). Note: Note the orientation of the white mark on retaining ring (48). 25. Steps 25 through 32 are for determining the proper number of shims (57) (not shown) that will be installed.
Illustration 15
g01409043
26. Measure Dimension (P) and record Dimension (P) on plate (58) to the nearest 0.010 mm (0.0004 inch).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/1/6
9/21
140M Series 2 Motor Grader - All Wheel Drive R9G00001-UP (MACHINE) POW...
10/21
27. Measure Dimension (R) and record Dimension (R) on washer (56) to the nearest 0.010 mm (0.0004 inch). 28. Measure Dimension (S) and record Dimension (S) on piston (59) to the nearest 0.010 mm (0.0004 inch). 29. Calculate Dimension (T) and record Dimension (T) to the nearest 0.010 mm (0.0004 inch). Note: Dimension (T) equals Dimension (R) plus Dimension (S). 30. Calculate Dimension (U) and record Dimension (U) to the nearest 0.010 mm (0.0004 inch). Note: Dimension (U) equals Dimension (T) minus Dimension (P). 31. Select a combination of shims (57) (not shown) that equals Dimension (U) minus 0.020 ± 0.010 mm (0.0008 ± 0.0004 inch). 32. Repeat Steps 26 through 31 for plate (62). Note: The slipper clearance is 0.020 ± 0.010 mm (0.0008 ± 0.0004 inch).
Illustration 16
g01408122
33. Install sleeves (55) and sleeves (60) into swashplate (54). 34. Install pistons (59) and washer (56) to swashplate (54). 35. Install the correct number of shims (61) that were determined in Step 32. Position plate (62). Apply Tooling (F) to screws (63). Install screws (63). Tighten screws (63) to a torque of 35 N·m (26 lb ft). 36. Install the correct number of shims (57) that were determined in Step 31. Position plate (58). Apply Tooling (F) to screws (63). Install screws (63). Tighten screws (63) to a torque of 35 N·m (26 lb ft).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/1/6
140M Series 2 Motor Grader - All Wheel Drive R9G00001-UP (MACHINE) POW...
Illustration 17
g01409370
37. Position swashplate assembly (42) into barrel assembly (37).
Illustration 18
g01409529
38. Install shaft (43) into barrel assembly (37) and swashplate assembly (42).
Illustration 19
g01409547
39. Install special washer (47) onto barrel assembly (37).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/1/6
11/21
140M Series 2 Motor Grader - All Wheel Drive R9G00001-UP (MACHINE) POW...
Illustration 20
12/21
g01409564
40. Raise the temperature of bearing cone (46). Install bearing cone (46) onto shaft (43). 41. Steps 42 through 54 are for determining the proper washer (28) (not shown) that will be installed.
Illustration 21
g01409596
Illustration 22
g01409572
42. Install barrel assembly (37) into housing (35). 43. Install ring (29) and O-ring seal (30) onto pipe (27A). Repeat this step for pipe (27B).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/1/6
140M Series 2 Motor Grader - All Wheel Drive R9G00001-UP (MACHINE) POW...
13/21
44. Install pipe (27A) and pipe (27B) into barrel assembly (37).
Illustration 23
g01409607
45. Center the swashplate to the zero displacement angle. Note: Each dimension that is measured and recorded is specific to each pipe (27A) and pipe (27B). 46. Attach Tooling (J) to housing (35). Measure Dimension (BB) and record Dimension (BB) to the nearest 0.010 mm (0.0004 inch). Measure Dimension (CC) and record Dimension (CC) to the nearest 0.010 mm (0.0004 inch). 47. Calculate Dimension (DD) and record Dimension (DD) to the nearest 0.010 mm (0.0004 inch). Note: Dimension (DD) equals Dimension (CC) minus Dimension (AA). 48. Calculate Dimension (EE) and record Dimension (EE) to the nearest 0.010 mm (0.0004 inch). Note: Dimension (EE) equals Dimension (CC) minus Dimension (BB).
Illustration 24
g01409686
49. Measure Dimension (FF) and record Dimension (FF) in housing (26) to the nearest 0.010 mm (0.0004 inch).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/1/6
140M Series 2 Motor Grader - All Wheel Drive R9G00001-UP (MACHINE) POW...
14/21
50. Measure Dimension (GG) and record Dimension (GG) in housing (26) to the nearest 0.010 mm (0.0004 inch). 51. Calculate Dimension (HH) and record Dimension (HH) to the nearest 0.010 mm (0.0004 inch). Note: Dimension (HH) equals Dimension (FF) minus Dimension (DD). 52. Calculate Dimension (JJ) and record Dimension (JJ) to the nearest 0.010 mm (0.0004 inch). Note: Dimension (JJ) equals Dimension (GG) minus Dimension (EE).
Illustration 25
g01409716
Pipe (27A) and pipe (27B) are shown for illustration purposes only.
Note: You must calculate a range for washer (28) that corresponds with each individual pipe (27A) and pipe (27B). 53. Select a washer (28) (not shown) that equals Dimension (HH) minus 0.080 ± 0.070 mm (0.0031 ± 0.0028 inch) for pipe (27A). Install washer (28) into housing (26). 54. Select a washer (28) (not shown) that equals Dimension (JJ) minus 0.080 ± 0.070 mm (0.0031 ± 0.0028 inch) for pipe (27B). Install washer (28) into housing (26).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/1/6
140M Series 2 Motor Grader - All Wheel Drive R9G00001-UP (MACHINE) POW...
Illustration 26
15/21
g01409572
55. Remove pipe (27A) and pipe (27B) from housing (35). Remove barrel assembly (37) from housing (35).
Illustration 27
g01407631
56. Install O-ring seal (40) onto piston (38). Repeat this step for the other piston.
Illustration 28
g01410022
57. Install rod (41). Install pistons (39) and (38). Note: The longer piston (39) is installed on the same side as rod (41).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/1/6
Thank you very much for your reading. Please Click Here. Then Get COMPLETE MANUAL. NO WAITING
NOTE: If there is no response to click on the link above, please download the PDF document first and then click on it.
140M Series 2 Motor Grader - All Wheel Drive R9G00001-UP (MACHINE) POW...
Illustration 29
16/21
g01410102
58. Apply Tooling (H) to seal (65). 59. Use Tooling (D) to install seal (65) into housing (35). 60. Use Tooling (E) to install retaining ring (64) into housing (35).
Illustration 30
g01407569
61. Apply Tooling (L) to shuttle valve (32). Use Tooling (B) to install shuttle valve (32) into housing (26). 62. Install relief valve (31).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/1/6
140M Series 2 Motor Grader - All Wheel Drive R9G00001-UP (MACHINE) POW...
Illustration 31
17/21
g01407324
63. Install retaining spring (19), spring (20), ring (21), retaining ring (22), and spring (23) into bushing (16). Install washer (18) and pilot valve (17) into bushing (16).
Illustration 32
g01410264
Improper assembly of parts that are spring loaded can cause bodily injury. To prevent possible injury, follow the established assembly procedure and wear protective equipment.
64. Install bushing (16) into housing (26). 65. Install pipe (27A) and pipe (27B) into housing (26). Note: Be sure that the correct pipe (27A) and pipe (27B) are installed into the correct cavity in housing (26).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/1/6
140M Series 2 Motor Grader - All Wheel Drive R9G00001-UP (MACHINE) POW...
Illustration 33
18/21
g01410274
66. Install port plate (36) onto housing (26).
Illustration 34
g01410304
67. Install barrel assembly (37) and swashplate assembly (42) onto housing (26).
Illustration 35
g01410343
68. Apply Tooling (K) to the mating surface of housing (26). Position housing (35) onto housing (26).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/1/6
140M Series 2 Motor Grader - All Wheel Drive R9G00001-UP (MACHINE) POW...
Illustration 36
19/21
g01410356
69. Reposition the wheel propel motor. Install bolts (24). Tighten bolts (24) to a torque of 87 N·m (64 lb ft). Install bolt (25). Tighten bolt (25) to a torque of 25 N·m (18 lb ft).
Illustration 37
g01407281
70. Install O-ring seal (12), O-ring seal (13), spring (14), and piston (15) into cover (8). Install retaining ring (11), washer (10), and plug (9) into cover (8). Tighten plug (9) to a torque of 10 N·m (89 lb in).
Illustration 38
g01407274
Improper assembly of parts that are spring loaded can cause bodily injury.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2020/1/6