Service Repair Manual
Models
140M 3 AWD MOTOR GRADER
140M Series 3 Motor Grader-All Wheel Drive N9G00001-UP (MACHINE) POWERE...
1/5
Shutdown SIS Previous Screen Product: MOTOR GRADER Model: 140M 3 AWD MOTOR GRADER N9G Configuration: 140M Series 3 Motor Grader-All Wheel Drive N9G00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly 12M Series 3, 140M Series 3 and 160M Series 3 Motor Graders Machine Systems Media Number -UENR3488-02
Publication Date -01/09/2018
Date Updated -24/09/2018
i07512054
Gerotor Motor (Circle Drive) - Assemble SMCS - 5082-016; 5206-016
Assembly Procedure Table 1 Required Tools Tool
Part Number
A
1P-0510
Part Description Driver Gp
Qty 1
1. Make sure that all the components of the gerotor motor are clean prior to assembly. During the assembly, check the condition of all the O-ring seals that are used in the motor. If any of the seals are damaged, use new parts for replacement.
Illustration 1
g00926979
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/12/31
140M Series 3 Motor Grader-All Wheel Drive N9G00001-UP (MACHINE) POWERE...
Illustration 2
g00926505
2. Install bearing (18). Use a suitable press to press bearing (18) to a depth of 7.62 mm (0.300 inch) below Surface (X). 3. Install lip seal (17). Press lip seal (17) in flush to 0.51 mm (0.020 inch) below face.
Illustration 3
g00926506
4. Install backup ring (19) and the shim to the motor assembly. 5. Install lip seal (20) to the motor assembly. 6. If equipped, install the needle bearing (13). Press the needle bearing to a depth of 2.92 mm (0.115 inch) below Surface (Z). Install O-ring seal (21) to the motor assembly.
Illustration 4
g00926242
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/12/31
2/5
140M Series 3 Motor Grader-All Wheel Drive N9G00001-UP (MACHINE) POWERE...
7. Position the motor assembly so that Face (Y) is facing upward. Install two races (15) and bearing (14) to shaft (16), as shown. 8. Install shaft (16) to the motor assembly.
Illustration 5
g00635545
9. Install link (11) and bearing (12) to the motor assembly.
Illustration 6
g00992953
10. Install spacer (10) and inner rotor (9) to the motor assembly. 11. Install the O-ring seal in outer rotor (7). Install pins (8) and outer rotor (7) to the motor assembly.
Illustration 7
g00635552
12. Install the O-ring seals on both sides of manifold (6). Install manifold (6) to the motor assembly.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/12/31
3/5
140M Series 3 Motor Grader-All Wheel Drive N9G00001-UP (MACHINE) POWERE...
Illustration 8
g00635553
13. Install a new ring (5) to inner plate (4). Note: Ring (5) is cone-shaped. The cone fits into the groove of inner plate (4).
Illustration 9
g00635555
14. Install inner plate (4). The seal ring should face the outer cap. Install outer plate (3) to the motor assembly.
Illustration 10
g00635556
15. Install cap (2) and bolts (1) on to the motor assembly. 16. Tighten bolts (1) to a torque of 68 ± 7 N·m (50 ± 5 lb ft). End By:
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/12/31
4/5
140M Series 3 Motor Grader-All Wheel Drive N9G00001-UP (MACHINE) POWERE...
1/2
Shutdown SIS Previous Screen Product: MOTOR GRADER Model: 140M 3 AWD MOTOR GRADER N9G Configuration: 140M Series 3 Motor Grader-All Wheel Drive N9G00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly 12M Series 3, 140M Series 3 and 160M Series 3 Motor Graders Machine Systems Media Number -UENR3488-02
Publication Date -01/09/2018
Date Updated -24/09/2018
i02798560
Gerotor Motor (Circle Drive) - Install SMCS - 5082-012; 5206-012
Installation Procedure Table 1 Required Tools Tool
Part Number
A
311-1362
Part Description Vacuum Cap
Qty 1
NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life.
Note: Check the O-ring seals for wear or for damage. Replace the components, if necessary.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/12/31
140M Series 3 Motor Grader-All Wheel Drive N9G00001-UP (MACHINE) POWERE...
Illustration 1
2/2
g01398364
1. Position the O-ring seal and gerotor motor (4). Install bolts (1). 2. Connect hose assemblies (3) and (2).
Illustration 2
g01397769
3. Remove Tooling (A). 4. Check the level of the hydraulic system. Refer to Operation and Maintenance Manual, "Hydraulic System Oil Level - Check" for the correct procedure. End By: a. Separate the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect". Copyright 1993 - 2019 Caterpillar Inc.
Tue Dec 31 10:24:30 UTC+0800 2019
All Rights Reserved. Private Network For SIS Licensees.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/12/31
140M Series 3 Motor Grader-All Wheel Drive N9G00001-UP (MACHINE) POWERE...
1/5
Shutdown SIS Previous Screen Product: MOTOR GRADER Model: 140M 3 AWD MOTOR GRADER N9G Configuration: 140M Series 3 Motor Grader-All Wheel Drive N9G00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly 12M Series 3, 140M Series 3 and 160M Series 3 Motor Graders Machine Systems Media Number -UENR3488-02
Publication Date -01/09/2018
Date Updated -24/09/2018
i05508935
Circle Drive - Remove SMCS - 5207-011
Removal Procedure Table 1 Required Tools Tool
Part Number
A
138-7575
Part Description Link Bracket
Qty 3
Start By: a. Remove the gerotor motor. Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/12/31
140M Series 3 Motor Grader-All Wheel Drive N9G00001-UP (MACHINE) POWERE...
Illustration 1
g00929322
1. Bend lock (1) from nut (2). Remove nut (2), lock (1), and washer (3). 2. Remove O-ring seal (4). Remove nuts (5).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/12/31
2/5
140M Series 3 Motor Grader-All Wheel Drive N9G00001-UP (MACHINE) POWERE...
Illustration 2
g00929323
3. Remove bolts (6). 4. Remove bolts (7).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/12/31
3/5
140M Series 3 Motor Grader-All Wheel Drive N9G00001-UP (MACHINE) POWERE...
Illustration 3
g00929325
5. Attach Tooling (A) to circle drive (8). Attach a suitable lifting device to Tooling (A). The weight of circle drive (8) is approximately 127 kg (280 lb). 6. Raise circle drive (8) and remove gear (9) and thrust washer (10).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/12/31
4/5
140M Series 3 Motor Grader-All Wheel Drive N9G00001-UP (MACHINE) POWERE...
Illustration 4
5/5
g00929328
7. Remove Duo-Cone seal (11) from circle drive (8). Remove circle drive (8).
Illustration 5
g00929332
8. Remove Duo-Cone seal (12) from gear (9). Copyright 1993 - 2019 Caterpillar Inc.
Tue Dec 31 10:25:26 UTC+0800 2019
All Rights Reserved. Private Network For SIS Licensees.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/12/31
140M Series 3 Motor Grader-All Wheel Drive N9G00001-UP (MACHINE) POWERE...
1/9
Shutdown SIS Previous Screen Product: MOTOR GRADER Model: 140M 3 AWD MOTOR GRADER N9G Configuration: 140M Series 3 Motor Grader-All Wheel Drive N9G00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly 12M Series 3, 140M Series 3 and 160M Series 3 Motor Graders Machine Systems Media Number -UENR3488-02
Publication Date -01/09/2018
Date Updated -24/09/2018
i05508896
Circle Drive - Disassemble SMCS - 5207-015
Disassembly Procedure Table 1 Required Tools Tool
Part Number
A
Part Description
Qty
Forcing Bolt 3/8-16 by 4 inch
2
B
138-7575
Link Bracket
1
C
8H-0663
Bearing Puller Gp
1
8B-7554
Bearing Cup Puller Gp
1
8B-7548
Push-Puller Tool Gp
1
D
Start By: a. Remove the circle drive. Refer to Disassembly and Assembly, "Circle Drive - Remove". Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior of the components should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism. Precision components can be damaged by contaminants or by dirt. Perform disassembly procedures on a clean work surface. Keep components covered and protected at all times.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/12/31
140M Series 3 Motor Grader-All Wheel Drive N9G00001-UP (MACHINE) POWERE...
Illustration 1
g00937730
1. Remove coupling (1) from housing (3). Remove pin (2) from coupling (1).
Illustration 2
g00937733
2. Remove nuts (4). Remove bracket (5).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/12/31
2/9
140M Series 3 Motor Grader-All Wheel Drive N9G00001-UP (MACHINE) POWERE...
3. Remove O-ring seal (7) and shims (8). 4. Remove bearing cup (6) from bracket (5).
Illustration 3
g00937735
5. Remove bolts (9) and cover (10). 6. Remove bolts (11).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/12/31
3/9
Thank you very much for your reading. Please Click Here. Then Get COMPLETE MANUAL. NO WAITING
NOTE: If there is no response to click on the link above, please download the PDF document first and then click on it.
140M Series 3 Motor Grader-All Wheel Drive N9G00001-UP (MACHINE) POWERE...
Illustration 4
g00937707
7. Install Tooling (A) and remove cover (12).
Illustration 5
g00937728
8. Remove plug (13) and O-ring seal (14) from cover (12). 9. Remove bearing (15) from cover (12).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/12/31
4/9
140M Series 3 Motor Grader-All Wheel Drive N9G00001-UP (MACHINE) POWERE...
Illustration 6
g00937708
10. Install Tooling (B) on shaft assembly (16). Attach a suitable lifting device to Tooling (B). The weight of shaft assembly (16) is approximately 32 kg (70 lb). 11. Remove shaft assembly (16). Remove Tooling (B).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/12/31
5/9
140M Series 3 Motor Grader-All Wheel Drive N9G00001-UP (MACHINE) POWERE...
Illustration 7
g00937732
12. Remove remaining bolts (17) and retainer (18). Remove spacer (19) and shims (20). 13. Remove spring (21) and spacer (22).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/12/31
6/9
140M Series 3 Motor Grader-All Wheel Drive N9G00001-UP (MACHINE) POWERE...
Illustration 8
7/9
g00937709
14. Remove gear (23) from shaft assembly (16). Remove friction discs (24) and discs (25) from gear (23). Remove spacer (26).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/12/31
140M Series 3 Motor Grader-All Wheel Drive N9G00001-UP (MACHINE) POWERE...
Illustration 9
8/9
g00937727
15. Remove thrust washer (27) and remove bearing (28). 16. Remove worm assembly (29) from housing (3).
Illustration 10
g00937739
17. Use Tooling (C) and a suitable press in order to remove bearings (31) from worm assembly (29).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/12/31