Service Repair Manual
Models
140M Motor Grader
140M Motor Grader - All Wheel Drive B9G00001-UP (MACHINE) POWERED BY ...
1/8
Shutdown SIS Previous Screen Product: MOTOR GRADER Model: 140M MOTOR GRADER B9G Configuration: 140M Motor Grader - All Wheel Drive B9G00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly 140M Motor Grader Media Number -KENR6424-07
Publication Date -01/04/2015
Date Updated -06/04/2015
i02837848
Blade Lift Cylinder - Remove and Install SMCS - 5102-010
Removal Procedure Table 1 Required Tools Tool
Part Number
Part Description
Qty
A
311-1362
Vacuum Cap
1
Cylinders equipped with lock valves can remain pressurized for very long periods of time, even with the hoses removed. Failure to relieve pressure before removing a lock valve or disassembling a cylinder can result in personal injury or death. Ensure all pressure is relieved before removing a lock valve or disassembling a cylinder.
NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2020/1/16
140M Motor Grader - All Wheel Drive B9G00001-UP (MACHINE) POWERED BY ...
2/8
Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on CatÂŽ products. Dispose of all fluids according to local regulations and mandates.
Hydraulic oil pressure can remain in the hydraulic system on this machine after the engine and pump have been stopped. Serious injury can result if this pressure is not released before any service is done on the hydraulic systems. In order to prevent possible injury, release the hydraulic system pressure before working on any fitting, hose, or hydraulic component. Lower all attachments to the ground before service is started. If the hydraulic system must be serviced, tested, or adjusted with the attachment in the raised position, the attachments and lift cylinders must be supported properly. Always move the machine to a location away from the travel of other machines. Be sure that other personnel are not near the machine when the engine is running and tests or adjustments are being made.
1. Release the system pressure. Refer to Operation and Maintenance Manual, "System Pressure Release".
Illustration 1
g01397769
2. Install Tooling (A) onto the hydraulic tank. Attach an air supply hose onto Tooling (A). Apply 138 kPa (20 psi). This procedure will pull a vacuum on the hydraulic system.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2020/1/16
140M Motor Grader - All Wheel Drive B9G00001-UP (MACHINE) POWERED BY ...
Illustration 2
g01415039
3. Disconnect hose assemblies (1). Remove clamp (2).
Illustration 3
g01415042
4. Remove bolts (6) and remove cap (7).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2020/1/16
3/8
140M Motor Grader - All Wheel Drive B9G00001-UP (MACHINE) POWERED BY ...
4/8
Note: Note the shims and inserts for installation purposes. 5. Attach a suitable lifting device to blade lift cylinder (5). The weight of blade lift cylinder (5) is approximately 59 kg (130 lb). 6. Remove bolts (3) and remove blade lift cylinder (5). 7. Remove cap assemblies (4) from blade lift cylinder (5).
Illustration 4
g01415199
8. Remove seal (8) from cap assembly (4). Remove bearing (9) from cap assembly (4). 9. Repeat Step 8 for the remaining cap assembly.
Disassembly and Assembly Information Table 2 Required Tools Tool
Part Number
Part Description
Qty
B
127-4904
Repair Stand
1
C
195-4609
Seal Pick
1
D
7M-7456
Bearing Mount Compound
1
E
1P-0808
Multipurpose Grease
1
9U-7868
Spanner Wrench
1
127-8064
Adjustable Plate
1
F
Cylinders equipped with lock valves can remain pressurized for very long periods of time, even with the hoses removed. Failure to relieve pressure before removing a lock valve or disassembling a cylinder can result in personal injury or death.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2020/1/16
140M Motor Grader - All Wheel Drive B9G00001-UP (MACHINE) POWERED BY ...
5/8
Ensure all pressure is relieved before removing a lock valve or disassembling a cylinder.
Illustration 5
g00931771
(1) Use a 46 mm socket in order to remove the bolt. Tighten the bolt to a torque of 1800 ± 200 N·m (1328 ± 148 lb ft). (2) Lubricate sealing lips with a thin covering of the lubricant that is being sealed. (3) Apply Tooling (D) to the seal groove prior to assembling the wiper seal. (4) Torque for head ... 600 ± 130 N·m (440 ± 95 lb ft) Note: Lubricate the threads with Tooling (E).
Installation Procedure Table 3 Required Tools Tool
Part Number
Part Description
Qty
A
311-1362
Vacuum Cap
1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2020/1/16
140M Motor Grader - All Wheel Drive B9G00001-UP (MACHINE) POWERED BY ...
G
183-3424
Grease Cartridge
1
H
1P-0510
Driver Gp
1
6/8
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
Illustration 6
g01415199
1. Use Tooling (H) (not shown) and a suitable press in order to install bearing (9) in cap assembly (4). Use Tooling (H) (not shown) in order to install seal (8) in cap assembly (4). 2. Repeat Step 1 for the remaining cap assembly.
Illustration 7
g01415042
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2020/1/16
140M Motor Grader - All Wheel Drive B9G00001-UP (MACHINE) POWERED BY ...
Illustration 8
7/8
g01415219
3. Install caps (4) on blade lift cylinder (5). 4. Attach a suitable lifting device to blade lift cylinder (5). The weight of blade lift cylinder (5) is approximately 59 kg (130 lb). 5. Position blade lift cylinder (5) on the machine. Install bolts (3). Torque bolts (3) to 115 ± 7 N·m (85 ± 5 lb ft). 6. Apply Tooling (G) between inserts (11) and ballstuds (12). Install cap (7) and install bolts (6). Note: As required, use shims (10) in order to allow the socket to move freely around ballstud (12). Assemble the same quantity of shims (10) on both sides of ballstud (12).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2020/1/16
140M Motor Grader - All Wheel Drive B9G00001-UP (MACHINE) POWERED BY ...
Illustration 9
8/8
g01415039
7. Install clamp (2). Connect hose assemblies (1).
Illustration 10
g01397769
8. Remove Tooling (A). 9. Check the hydraulic oil level. Refer to Operation and Maintenance Manual, "Hydraulic System Oil Level - Check" for the correct procedure. Copyright 1993 - 2020 Caterpillar Inc.
Thu Jan 16 12:40:20 UTC+0800 2020
All Rights Reserved. Private Network For SIS Licensees.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2020/1/16
140M Motor Grader - All Wheel Drive B9G00001-UP (MACHINE) POWERED BY ...
1/8
Shutdown SIS Previous Screen Product: MOTOR GRADER Model: 140M MOTOR GRADER B9G Configuration: 140M Motor Grader - All Wheel Drive B9G00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly 140M Motor Grader Media Number -KENR6424-07
Publication Date -01/04/2015
Date Updated -06/04/2015
i02798701
Sideshift Cylinder - Remove and Install SMCS - 5804-010
Removal Procedure Table 1 Required Tools Tool
Part Number
A
311-1362
Part Description Vacuum Cap
Qty 1
Start By: a. Connect the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock Separate and Connect".
Cylinders equipped with lock valves can remain pressurized for very long periods of time, even with the hoses removed. Failure to relieve pressure before removing a lock valve or disassembling a cylinder can result in personal injury or death. Ensure all pressure is relieved before removing a lock valve or disassembling a cylinder.
NOTICE Keep all parts clean from contaminants.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2020/1/16
140M Motor Grader - All Wheel Drive B9G00001-UP (MACHINE) POWERED BY ...
2/8
Contaminants may cause rapid wear and shortened component life.
NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on CatÂŽ products. Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil. Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system. Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2020/1/16
140M Motor Grader - All Wheel Drive B9G00001-UP (MACHINE) POWERED BY ...
Illustration 1
3/8
g01398678
1. Extend side shift cylinder (2) to the left. Move the blade to the forward position. 2. Remove cotter pin (3) (not shown) in order to remove pin (1). Remove bolts (4) in order to remove bracket (5). 3. Retract side shift cylinder (2). 4. Release the system pressure. Refer to Operation and Maintenance Manual, "System Pressure Release".
Illustration 2
g01397769
5. Install Tooling (A) onto the hydraulic tank. Attach an air supply hose onto Tooling (A). Apply 138 kPa (20 psi). This procedure will pull a vacuum on the hydraulic system.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2020/1/16
140M Motor Grader - All Wheel Drive B9G00001-UP (MACHINE) POWERED BY ...
Illustration 3
g01398701
6. Disconnect hose assemblies (6).
Illustration 4
g01398731
7. Remove cotter pin (7). Remove pin (8) and washers (9). Note: Note the number and the location of washers (9) for assembly purposes.
Illustration 5
g01398735
8. Attach a suitable lifting device to sideshift cylinder (2). The weight of sideshift cylinder (2) is approximately 91 kg (200 lb). Slide sideshift cylinder (2) to the left and remove sideshift cylinder (2).
Disassembly and Assembly Information Table 2 Required Tools Tool
Part Number
Part Description
Qty
B
127-4904
Hydraulic Cylinder Repair Stand Gp
1
C
195-4609
Seal Pick
1
D
9U-7868
Spanner Wrench
1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2020/1/16
4/8
140M Motor Grader - All Wheel Drive B9G00001-UP (MACHINE) POWERED BY ...
127-8064
Adapter Plate Gp
1
E
4C-4032
Bearing Mount Compound
1
F
9U-6539
Socket
1
G
1P-0808
Multipurpose Grease
1
5/8
Cylinders equipped with lock valves can remain pressurized for very long periods of time, even with the hoses removed. Failure to relieve pressure before removing a lock valve or disassembling a cylinder can result in personal injury or death. Ensure all pressure is relieved before removing a lock valve or disassembling a cylinder.
Illustration 6
g01012935
(1) Use Tooling (F) in order to torque the bolt. Tighten the bolt to a torque of 900 ± 100 N·m (660 ± 75 lb ft). (2) Lubricate sealing lips with a thin covering of the lubricant that is being sealed. (3) Apply Tooling (E) to the wiper seal groove before you assemble the wiper seal to the head. Note: Lubricate the threads with clean grease and torque head (4) to 600 ± 130 N·m (440 ± 95 lb ft). Use Tooling (G) to apply the grease.
Installation Procedure
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2020/1/16
140M Motor Grader - All Wheel Drive B9G00001-UP (MACHINE) POWERED BY ...
Table 3 Required Tools Tool
Part Number
A
311-1362
Part Description Vacuum Cap
Qty 1
NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life.
Illustration 7
g01398735
1. Use a suitable lifting device in order to install sideshift cylinder (2). The weight of sideshift cylinder (2) is approximately 91 kg (200 lb).
Illustration 8
g01398731
2. Position washers (9) and install pin (8). Install cotter pin (7).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2020/1/16
6/8
Thank you very much for your reading. Please Click Here. Then Get COMPLETE MANUAL. NO WAITING
NOTE: If there is no response to click on the link above, please download the PDF document first and then click on it.
140M Motor Grader - All Wheel Drive B9G00001-UP (MACHINE) POWERED BY ...
Illustration 9
g01398701
3. Connect hose assemblies (6).
Illustration 10
g01398678
4. Extend side shift cylinder (2) to the left. 5. Position bracket (5). Align side shift cylinder (2) and install pin (1). Install cotter pin (3) (not shown).
Illustration 11
g01397769
6. Remove Tooling (A).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2020/1/16
7/8
140M Motor Grader - All Wheel Drive B9G00001-UP (MACHINE) POWERED BY ...
8/8
7. Check the hydraulic oil level. Refer to Operation and Maintenance Manual, "Hydraulic System Oil Level - Check". End By: a. Separate the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock Separate and Connect". Copyright 1993 - 2020 Caterpillar Inc.
Thu Jan 16 12:41:15 UTC+0800 2020
All Rights Reserved. Private Network For SIS Licensees.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2020/1/16
140M Motor Grader - All Wheel Drive B9G00001-UP (MACHINE) POWERED BY ...
1/9
Shutdown SIS Previous Screen Product: MOTOR GRADER Model: 140M MOTOR GRADER B9G Configuration: 140M Motor Grader - All Wheel Drive B9G00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly 140M Motor Grader Media Number -KENR6424-07
Publication Date -01/04/2015
Date Updated -06/04/2015
i02797651
Centershift Cylinder - Remove and Install SMCS - 5223-010
Removal Procedure Start By: a. Connect the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock Separate and Connect".
Cylinders equipped with lock valves can remain pressurized for very long periods of time, even with the hoses removed. Failure to relieve pressure before removing a lock valve or disassembling a cylinder can result in personal injury or death. Ensure all pressure is relieved before removing a lock valve or disassembling a cylinder.
NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2020/1/16
140M Motor Grader - All Wheel Drive B9G00001-UP (MACHINE) POWERED BY ...
2/9
Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on CatÂŽ products. Dispose of all fluids according to local regulations and mandates.
Hydraulic oil pressure can remain in the hydraulic system on this machine after the engine and pump have been stopped. Serious injury can result if this pressure is not released before any service is done on the hydraulic systems. In order to prevent possible injury, release the hydraulic system pressure before working on any fitting, hose, or hydraulic component. Lower all attachments to the ground before service is started. If the hydraulic system must be serviced, tested, or adjusted with the attachment in the raised position, the attachments and lift cylinders must be supported properly. Always move the machine to a location away from the travel of other machines. Be sure that other personnel are not near the machine when the engine is running and tests or adjustments are being made.
1. Release the system pressure. Refer to Operation and Maintenance Manual, "System Pressure Release".
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2020/1/16