Service Repair Manual
Models
424D Backhoe Loader
424D Backhoe Loader BGP00648-01612 (MACHINE) POWERED BY 3054B Engine...
2/10
S/N - BPE1-UP S/N - BPN1-UP S/N - BRG1-UP S/N - BRY1-UP S/N - FDP1-UP S/N - MBH1-UP
Disassembly Procedure Table 1 Required Tools Tool
Part Number
Part Description
Qty
A
6V-3010
Puller Group
1
B
9S-7338
Crossblock
1
C
1U-6400
Three Jaw Puller
1
D
8T-0978
Puller Sleeve
1
E
8H-0663
Bearing Puller Gp
1
F
140-0168
Puller
1
G
140-0169
Puller
1
H
1P-1861
Retaining Ring Pliers
1
I
1P-0510
Driver Gp
1
J
140-0165
Puller
1
Start By: A. Remove tie rods. See Disassembly and Assembly, "Tie rod (Steering) (Front) - Remove and Install".
NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2019/12/3
424D Backhoe Loader BGP00648-01612 (MACHINE) POWERED BY 3054B Engine...
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates.
Illustration 1
g00779601
1. Remove bolts (1) .
Illustration 2
g00779608
2. Remove the carrier gear (2) with Tooling (A) .
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2019/12/3
3/10
424D Backhoe Loader BGP00648-01612 (MACHINE) POWERED BY 3054B Engine...
Illustration 3
g00779611
3. Remove the hub (3) from the steer axle hub (4) with Tooling (B) .
Illustration 4
g00779620
4. Remove the rubber O-ring seal (5) from the hub.
Illustration 5
g00779628
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2019/12/3
4/10
424D Backhoe Loader BGP00648-01612 (MACHINE) POWERED BY 3054B Engine...
5/10
5. Pry shaft seal (6) from the hub. If necessary, drive the outer bearing cones out of the hub bores.
Illustration 6
g00779636
6. Remove the inner bearing cone with Tooling (C) and (D) .
Illustration 7
g00779646
7. Remove the bolts (7) and the axle kingpins (8) from the top and the bottom of the steer axle hub (4) .
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2019/12/3
424D Backhoe Loader BGP00648-01612 (MACHINE) POWERED BY 3054B Engine...
Illustration 8
g00779663
Illustration 9
g00779666
8. Press bearing cone (9) and shaft seal (10) from the axle kingpins (8) with Tooling (E) .
Illustration 10
g00779685
9. Remove shim (11) .
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2019/12/3
6/10
424D Backhoe Loader BGP00648-01612 (MACHINE) POWERED BY 3054B Engine...
Illustration 11
7/10
g00779681
10. Attach link brackets (12) and a suitable lifting device. Remove the steer axle hub (4) and the axle shaft from the axle housing (13). The weight of the steer axle hub and axle shaft is approximately 40 kg (88 lb).
Illustration 12
g00779691
11. Expand the retaining ring (14). Separate the sun gear (15) from the steer axle hub.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2019/12/3
424D Backhoe Loader BGP00648-01612 (MACHINE) POWERED BY 3054B Engine...
Illustration 13
8/10
g00779702
12. Remove snap ring (16) and separate the axle shaft (17) from the steer axle hub (4) .
Illustration 14
g00779739
13. Press the bushing assembly and the shield body (18) from the axle shaft with Tooling (E) .
Illustration 15
g00779757
14. Pull the shaft seal (19) out of the steer axle hub with Tooling (F) and (G) .
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2019/12/3
424D Backhoe Loader BGP00648-01612 (MACHINE) POWERED BY 3054B Engine...
Illustration 16
g00779769
15. Remove the retaining ring (20) from the steer axle hub (4) with Tooling (H) .
Illustration 17
g00779780
16. Remove the bearing from steer axle hub (4) with Tooling (I) .
Illustration 18
g00779786
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2019/12/3
9/10
424D Backhoe Loader BGP00648-01612 (MACHINE) POWERED BY 3054B Engi...
10/10
17. Pull the upper bearing cone (21) and the lower bearing cone out of the axle housing with Tooling (F) and (G) .
Illustration 19
g00779789
18. Pull the shaft seal (22) from the axle housing with Tooling (F) and (G) .
Illustration 20
g00779792
19. Pull the bearing cone (23) from the axle housing with Tooling (F) and (J) . Copyright 1993 - 2019 Caterpillar Inc.
Tue Dec 3 23:28:15 UTC+0800 2019
All Rights Reserved. Private Network For SIS Licensees.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2019/12/3
424D Backhoe Loader BGP00648-01612 (MACHINE) POWERED BY 3054B Engine...
Illustration 1
g00780072
1. Drive the sleeve into the axle housing with tooling (A) .
Illustration 2
g00780073
2. Drive the shaft seal against the shoulder with tooling (B). The seal lip should face the oil chamber.
Illustration 3
g00780079
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2019/12/3
3/9
424D Backhoe Loader BGP00648-01612 (MACHINE) POWERED BY 3054B Engine...
4/9
3. Insert the two bearing races in the steer axle hub until contact is contained with tooling (A) .
Illustration 4
g00780087
4. Press the bearing into the bore of the steer axle hub until contact is obtained with tooling (A) .
Illustration 5
g00780089
5. Install retaining ring (1) with tooling (C) .
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2019/12/3
424D Backhoe Loader BGP00648-01612 (MACHINE) POWERED BY 3054B Engine...
Illustration 6
g00780093
6. Install the shaft seal (2) with tooling (D). the seal lip should face the bearing.
Illustration 7
g00780100
7. Assemble shield (3) and heated sleeve (4) on axle shaft (5). Position the shield against the shoulder.
Illustration 8
g00780105
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2019/12/3
5/9
424D Backhoe Loader BGP00648-01612 (MACHINE) POWERED BY 3054B Engine...
8. Install the assembled axle shaft (5) into the steer axle hub (6) .
Illustration 9
g00780111
9. Install the retaining ring (7) in order to secure the axle shaft with tool (C) .
Illustration 10
g00780117
10. Install the sun gear (8) on the axle shaft. Secure the gear with the retaining ring (9) .
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2019/12/3
6/9
424D Backhoe Loader BGP00648-01612 (MACHINE) POWERED BY 3054B Engine...
Illustration 11
7/9
g00780119
11. Install the steer axle hub (6) and the axle shaft into the axle housing until the splines are seated in the side gear.
Illustration 12
g00780125
12. Install the shim (10) and the axle kingpin in the top of the steer axle hub (6). Install the axle kingpin without a shim in the bottom of the steer axle hub (6) .
Illustration 13
g00780132
13. Install bolts (11) and tighten to a torque of 117 N¡m (86 lb ft). 14. Move the steer axle hub back and forth. Use a torque wrench in order to check the rolling resistance. The rolling resistance should be 18 to 20 N¡m (13 to 15 lb ft). If the rolling resistance is greater than specification, remove the shim (10). Replace the shim with a thicker shim. If the rolling resistance is less than specification, remove shim (10). Replace the shim with a thinner shim.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2019/12/3
424D Backhoe Loader BGP00648-01612 (MACHINE) POWERED BY 3054B Engine...
Illustration 14
g00780149
15. Press both of the outer races firmly against the shoulder with tooling (E) .
Illustration 15
g00780151
16. Press in the shaft seal with the words on top until the seal is flush with tool (F) .
Illustration 16
g00780153
17. Assemble the heated bearing race (12) on the steer axle hub (6) until contact is obtained.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2019/12/3
8/9
424D Backhoe Loader BGP00648-01612 (MACHINE) POWERED BY 3054B Engine...
Illustration 17
9/9
g00780156
18. Install the hub (13) on the steer axle hub (6). Fix the hub with the heated inner bearing race (14) .
Illustration 18
g00780159
19. Assemble internal gear (15) and install bolts (16). Tighten bolts (16) to a torque of 68 N¡m (51 lb ft). End By: Install the planetary hub of the final drive. See Disassembly and Assembly, "Final Drive (Drive and Steering Axle) (Front) Assemble". Copyright 1993 - 2019 Caterpillar Inc.
Tue Dec 3 23:29:11 UTC+0800 2019
All Rights Reserved. Private Network For SIS Licensees.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2019/12/3
424D Backhoe Loader BGP00648-01612 (MACHINE) POWERED BY 3054B Engine...
1/4
Shutdown SIS Previous Screen Product: BACKHOE LOADER Model: 424D BACKHOE LOADER BGP Configuration: 424D Backhoe Loader BGP00648-01612 (MACHINE) POWERED BY 3054B Engine
Disassembly and Assembly 416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Power Train Media Number -RENR3578-12
Publication Date -01/04/2010
Date Updated -13/04/2010
i01505249
Drive and Steering Axle Housing (Front) - Install SMCS - 3260-012-FR S/N - B2D1-UP S/N - BFP1-UP S/N - BGJ1-UP S/N - BGP1-UP S/N - BKC1-UP S/N - BKG1-UP S/N - BKR1-UP S/N - BLD1-UP S/N - BLL1-UP S/N - BLN1-UP S/N - BMC1-UP S/N - BML1-UP S/N - BMT1-UP S/N - BNB1-UP S/N - BNK1-UP S/N - BNS1-UP
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2019/12/3
Thank you very much for your reading. Please Click Here. Then Get COMPLETE MANUAL. NO WAITING
NOTE: If there is no response to click on the link above, please download the PDF document first and then click on it.
424D Backhoe Loader BGP00648-01612 (MACHINE) POWERED BY 3054B Engine...
2/4
S/N - BPE1-UP S/N - BPN1-UP S/N - BRG1-UP S/N - BRY1-UP S/N - FDP1-UP S/N - MBH1-UP
Installation Procedure
Illustration 1
g00780931
1. Use a suitable lifting device in order to install the axle housing. Lift the axle housing at the arrows. Note: The weight of the axle housing is approximately 68 kg (150 lb).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2019/12/3
424D Backhoe Loader BGP00648-01612 (MACHINE) POWERED BY 3054B Engine...
Illustration 2
3/4
g00780931
2. Use the suitable lifting device in order to support the axle housing. Support the axle housing at the arrows.
Illustration 3
g00780940
3. Install bolts (3) into the axle housing.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2019/12/3
424D Backhoe Loader BGP00648-01612 (MACHINE) POWERED BY 3054B Engine...
Illustration 4
4/4
g00780926
4. Install the ball joint end of the tie rod into steering housing (2). Install tie rod nut (1). Tighten nut (1) to a torque of 165 N¡m (122 lb ft). Install the cotter pin. 5. Fill the differential housing with the proper lubricants. Refer to the Operation and Maintenance Manual for the proper types and volumes of lubricant. End By: Install the front axle. See Disassembly and Assembly, "Drive and Steering Axle (Front) Install". Copyright 1993 - 2019 Caterpillar Inc.
Tue Dec 3 23:30:07 UTC+0800 2019
All Rights Reserved. Private Network For SIS Licensees.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2019/12/3