8002E by FlexiForce

Universal 2 Channel Receiver Model 8002E DISCONNECT POWER TO GARAGE DOOR OPENER BEFORE INSTALLING RECEIVER. For use with the following RF modules: • 801221 Superheterodyne, 433.92MHz • 801504 Superregenerative, 433.92MHz • 801344 Superregenerative, 418MHz • 801429 Superheterodyne, 27.145MHz

SPECIFICATIONS Output Rating ......................................I max. = 5 A; V max. = 30V AC/DC Power input..........................................................9-35V AC/DC, @ 30 mA RF Frequency.......................................27.145MHz, 418MHz, 433.92MHz

Antenna Connection RECEIVER CIRCUIT BOARD

The 2 Channel Universal Receiver Model 8002E can be programmed to receive up to 15 codes for each channel.

Ant.

OUTPUT DURATION JUMPERS:

1B2

B Channel

1A2

A Channel

Receiver

PROGRAMMING THE RECEIVER TO ACCEPT YOUR TRANSMITTER CODE Activate the opener only when door is in full view, free of obstruction and properly adjusted. No one should enter or leave garage while door is in motion. Do not allow children to operate push button(s) or remote(s). Do not allow children to play near the door.

5V/8V

TERMINALS: 1 2 3 4 5 6

To Transformer To Push Button Control Channel B To Push Button Control Channel A

Indicator Lights (A & B Channels) A

B TEST/TEST B 6 5 4 3 2 1 A LEARN/LERN OUT.A OUT.B A B 12 -24V AC/DC 12-24 V

INSTALLATION The receiver should be mounted towards the front of the garage, preferably about two meters above the floor. Select a location which allows clearance for opening the cover, and space for the antenna (as far from metal structures as possible). The receiver and antenna use TV Type F coaxial connectors. The antenna is threaded directly onto the receiver. An optional remote antenna mounting kit is available if more range is needed. The transformer (Model 23009E) must be plugged into the wall within two meters of the receiver, to allow the wire to reach the receiver terminals. 1. Fasten the receiver securely with screws through the corner holes which are located under the cover. 2. Inside the receiver, locate the terminals on the circuit board (see illustration). Connect the transformer wire to the block under terminals 1 and 2. 3. Connect the wire from your wall mounted door control (or other push button) to channel A terminals 5 and 6. Connect the wires for a second door control (if there are two doors to control) to channel B terminals 3 and 4. If no wall control (or other push button) is used, refer to your garage door opener owner’s manual. 4. Plug in the transformer and reconnect power. You may use each command button to operate your opener(s).

Program Buttons (A & B Channels) Command Buttons (A & B Channels)

TO SET OUTPUT DURATION The receiver can be set for either CONSTANT constant or momentary closure on the (Deadman) output contacts for each channel (A and B). (Use constant closure only if constant pressure is needed.) With the jumper in 1B 2 “1” (Momentary) position, the contacts will close for 150ms regardless of the MOMENTARY length of radio Jumper in transmission. With Position 2 the jumper in “2” (Constant) position, 1B 2 the contacts will stay closed as long as the radio continues transmitting. Jumper in Position 1 The receiver is factory set at 1. When using module 801243 please switch Jumper 8V/5V to 5V.

1. Press and hold the remote control push button. 2. Press and release the program button in the Control Center on the opener panel. The indicator light will flash once. 3. Release the remote push button. Now the opener will operate when the remote control push button is pressed. If you release the remote control push button before the indicator lights flash, the opener will not accept the code.

Repeat steps 1 – 3 to program the receiver for all remote controls in use for that door. If a second door is in use, use a different remote control button and repeat the steps for channel B. Replace top cover with mounting screws. To erase all codes from the receiver: hold the receiver’s program button until the indicator light goes off (after 6 seconds). All codes

114A2460-GB

DECLARATION OF CONFORMITY Universal 2 Channel Radio Receiver............................................................Model No. 8002E is in conformity to the applicable sections of Standards............. ETS 300 683, ETS 300 220, BAPT 222 ZV 125, per the provisions & all amendments of the EU Directives .89/336/EEC DECLARATION OF INCORPORATION Universal 2 Channel Radio Receiver Model No. 8002E, when installed and maintained according to all the Manufacturer’s instructions in combination with a Garage Door Opener and Garage Door, which have also been installed and maintained according to all the Manufacturer’s instructions, meets the provisions of EU Directive 89/392/EEC and all amendments. I, the undersigned, hereby declare that the equipment specified above and any accessory listed in the manual conforms to the above Directives and Standards. Chamberlain GmbH D-66793 Saarwellingen Colin B. Willmott, Chefingenieur April 2000