BEARINGS & POWER TRANSMISSION
832
Ball & Roller Bearings 873 - 884 Ball Joints & Rod Ends 892 - 894 Belts, Pulleys & Accessories 902 - 905 Bushing Bearings & Shafts 848 - 855 Cam Followers 907 - 911 Collars & Couplings 886 - 887, 889 - 891 Gas Springs, Shocks & Dampers 914 - 921 Gears, Racks & Keyed Shafts 888 - 889, 891 Linear Motion Components 834 - 847, 856 - 861, 896 - 899 Mounted Bearings 862 - 872
833
LINEAR MOTION SLIDES Cross Roller Slide Assemblies
s s s s s s
For higher load carrying capacity than precision ball slide assemblies and when operating at high cycling rates or with shock and overhanging loads, cross roller slides are used for improved performance. Cross roller slides provide accuracy of .0001" of travel, repeatability .0001" exceeding precision ball slides. Cross roller slides are not as naturally cleaning as ball slides. In operating environments with little or no protection against dust and when heavy loads are not a consideration, consider ball slides.
Positive stops prevent over-travel Rollers improve load capacity 8-10 times that of balls Alternately crossed rollers handle force in any direction Lightweight aluminum carriage and base Interchangeable with many types of ball slides Four tapped and threaded carriage holes and two counter bored base holes simplify installation and component mounting
Item No.
Travel
Load Capacity (Lbs.)
A
B
C
Carriage Hole Spacing D
E
F
Base Dimension Hole Spacing G
H
Base and Carriage Holes I and J
Pack Qty.
DT-71 DT-72 DT-73 DT-81 DT-82 DT-83 DT-92 DT-93 DT-94 DT-121 DT-122 DT-123 DT-124 DT-131 DT-132 DT-133 DT-141 DT-142 DT-143 DT-144 DT-146*
.50 1 2 .50 1 2 1.5 2 3 1 2 3 4 1 2 3 1.5 2 3 4 6
30 55 66 48 78 94 132 220 264 132 176 176 308 132 176 176 264 352 440 440 704
1.06 2.06 3.06 1.06 2.06 3.06 2.56 3.56 4.56 2.00 3.00 4.00 6.00 2.00 3.25 4.00 2.62 4.00 5.00 6.00 9.00
.32 .32 .32 .40 .40 .40 .53 .53 .53 .62 .62 .62 .62 .75 .75 .75 1.00 1.00 1.00 1.00 1.00
.56 .56 .56 .75 .75 .75 1.06 1.06 1.06 1.50 1.50 1.50 1.50 1.75 1.75 1.75 2.62 2.62 2.62 2.62 2.62
.625 1.625 2.625 .625 1.625 2.625 2.250 3.250 4.000 1.375 2.375 3.375 5.375 1.375 2.625 3.375 1.625 3.000 4.000 5.000 3.000
.218 .218 .218 .375 .375 .375 .437 .437 .437 .625 .625 .625 .625 .875 .875 .875 1.250 1.250 1.250 1.250 1.250
.187 .187 .187 .250 .250 .250 .312 .312 .312 .340 .340 .340 .340 .400 .400 .400 .625 .625 .625 .625 .625
.250 .250 .250 .375 .375 .375 .500 .500 .500 .750 .750 .750 .750 .875 .875 .875 1.500 1.500 1.500 1.500 1.500
.750 1.375 2.375 .750 1.375 2.375 2.125 3.125 3.250 1.500 2.500 3.500 4.000 1.625 2.750 3.500 1.875 3.375 4.375 5.375 7.000
2-56 2-56 2-56 4-40 4-40 4-40 6-32 6-32 6-32 6-32 6-32 6-32 6-32 6-32 6-32 6-32 10-32 10-32 10-32 10-32 10-32
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
*Has 6 carriage holes. D Carriage Hole Spacing value is minimum centered around mean position.
Low Profile Crossed Roller Slide Tables
Crossed roller slide tables are factory assembled and ready to install. They use crossed roller bearings to provide very precise linear motion with low friction and high support stiffness for the load. A large selection is available for applications including precision instruments, office and communications equipment, surface grinders, tool grinders, assembly fixtures, and anywhere precise linear positioning is required. Precision ground "V" grooved ways and rollers provide high accuracy and load capacity. Withstands forces in any direction from alternately crossed rollers at 45 degree angle. Contain UNC threaded mounting holes in standard pattern for easy installation. Interchangeable with other manufacturers slides. Straight line accuracy .0001" inch of travel. .0001" position repeatability. All have light weight aluminum carriage. Steel type has hardened steel crossed roller rail set with double V grooved inner rail. Stainless steel type (DT-432 and 445) has stainless steel rollers, cages and fasteners.
Item No.
Travel
DT-401 DT-432* DT-408 DT-409 DT-411 DT-412 DT-415 DT-445* DT-416 DT-418 DT-419 DT-421
.473 .709 .709 1.181 1.969 2.363 1.181 1.181 1.772 2.953 3.543 5.118
*Stainless steel
834
Load Capacity Length (Lbs.) L
50 70 88 138 209 231 277 277 404 605 682 825
.984 1.378 1.378 1.969 3.150 3.740 2.165 2.165 3.150 5.118 6.102 8.070
Base Mounting Holes-Spacing and Dimensions (Counterbored) A
B
C
No. of Holes
.315 .315 .472 .472 .472 .472 .630 .630 .630 .630 .630 .630
.788 .788 1.181 1.181 1.181 1.181 1.575 1.575 1.575 1.575 1.575 1.575
.158 .158 .236 .236 .236 .236 .315 .315 .315 .315 .315 .315
2 2 2 2 4 4 2 2 4 4 4 4
U
W
R
D
.709 .984 .984 1.378 2.756 3.347 1.575 1.575 2.677 4.528 5.512 7.480
— — — — 1.575 1.772 — — 1.693 2.559 3.740 3.543
.138 .197 .197 .295 .197 .197 .295 .295 .236 .295 .295 .295
.155 — .241 — — — .327 .327 — — — —
Carriage Holes-Spacing and Dimensions (Threaded) d
No. of Holes
M
N
P
Thread
Depth
Pack Qty.
— 2-56 — 6-32 6-32 6-32 — — 10-32 10-32 10-32 10-32
4 4 4 4 4 6 4 4 4 4 6 6
.709 1 x 1.102 1 x 1.102 1 x 1.693 1 x 1.772 2 x 1.181 1 x 1.575 1 x 1.575 1 x 2.560 1 x 2.953 2 x 1.969 2 x 2.953
.138 .138 .138 .138 .689 .689 .295 .295 .295 1.083 1.083 1.083
.551 .551 .866 .866 .866 .866 1.181 1.181 1.181 1.181 1.181 1.181
2-56 2-56 6-32 6-32 6-32 6-32 10-32 10-32 10-32 10-32 10-32 10-32
.138 .138 .217 .217 .217 .217 .295 .295 .295 .295 .295 .295
1 1 1 1 1 1 1 1 1 1 1 1
LINEAR MOTION SLIDES Precision Ball Slide Assemblies
C E B
A D
I F
J
G
H
These precision linear ball slides have a typical coefficient of friction of .003 and provide straight line accuracy of .0005" per inch of travel. At load capacity, a life of 10 million inches of travel can be expected. The expected life at 1â „2 the rated load is 100 million inches. s s s s s s
Factory preload adjustment prevents sideplay and backlash Lightweight aluminum carriage and base with high load capacity Four tapped and threaded carriage holes and counter bored base holes simplify installation and component mounting Long life, self-cleaning ball bearing needs no lubrication Positional repeatability .0002 inch Clear anodized finish
Item No.
DT-11* DT-12* DT-13* DT-21 DT-22 DT-23 DT-24 DT-25 DT-26 DT-31 DT-32 DT-33 DT-34 DT-35 DT-36 DT-101 DT-102 DT-1025 DT-103 DT-104 DT-41 DT-42 DT-43 DT-44 DT-46 DT-48 DT-111 DT-112 DT-113 DT-1135 DT-114 DT-116 DT-118 DT-51 DT-515 DT-52 DT-53 DT-54 DT-55 DT-56 DT-61 DT-615 DT-62 DT-63 DT-64 DT-65 DT-66** DT-69** DT-612**
Carriage Hole Spacing
Base Hole Dimensions
Travel
Load Capacity (Lbs.)
A
B
C
D
E
F
G
Hole Spacing H
Carriage Hole I
Base Hole J
Pack Qty.
.50 1 1.5 .50 1.00 2.00 3.00 4.00 5.00 .50 1.00 2.00 3.00 4.00 5.00 .50 1.00 1.50 2.00 3.00 .75 1.50 2.00 3.00 4.00 6.00 1.00 2.00 3.00 3.50 4.00 6.00 8.00 1.00 1.50 2.00 3.00 4.00 6.00 8.00 1.00 1.50 2.00 3.00 4.00 5.00 6.00 9.00 12.00
1.5 1.5 1.5 4 8 12 14 16 18 8 10 12 14 16 18 10 12 13 15 18 15 18 20 25 30 35 15 20 25 30 35 45 55 20 30 42 52 60 75 90 30 35 62 88 118 135 150 185 205
.75 1.25 1.75 1.06 2.06 3.06 4.06 5.06 6.06 1.06 2.06 3.06 4.06 5.06 6.06 1.56 2.56 3.06 3.56 4.56 1.56 2.56 3.56 4.56 6.00 8.00 2.00 3.00 4.00 5.00 6.00 8.00 10.00 2.00 2.75 3.25 4.00 6.00 8.00 10.00 2.62 2.62 4.00 5.00 6.00 8.00 9.00 12.00 15.00
.23 .23 .23 .32 .32 .32 .32 .32 .32 .41 .41 .41 .41 .41 .41 .50 .50 .50 .50 .50 .53 .53 .53 .53 .53 .53 .62 .62 .62 .62 .62 .62 .62 .75 .75 .75 .75 .75 .75 .75 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00
.38 .38 .38 .56 .56 .56 .56 .56 .56 .75 .75 .75 .75 .75 .75 1.00 1.00 1.00 1.00 1.00 1.06 1.06 1.06 1.06 1.06 1.06 1.50 1.50 1.50 1.50 1.50 1.50 1.50 1.75 1.75 1.75 1.75 1.75 1.75 1.75 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62 2.62
.375 .875 1.375 .625 1.625 2.625 3.625 4.625 5.625 .625 1.625 2.625 3.625 4.625 5.625 1.250 2.250 2.750 3.250 4.250 1.250 2.250 3.250 4.000 5.500 7.500 1.375 2.375 3.375 4.375 5.375 7.375 9.375 1.375 2.125 2.625 3.375 5.500 7.500 9.500 2.125 1.625 3.000 4.000 5.000 7.000 3.000 3.000 3.000
.156 .156 .156 .218 .218 .218 .218 .218 .218 .375 .375 .375 .375 .375 .375 .437 .437 .437 .437 .437 .437 .437 .437 .437 .437 .437 .625 .625 .625 .625 .625 .625 .625 .875 .875 .875 .875 .875 .875 .875 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250
.135 .135 .135 .187 .187 .187 .187 .187 .187 .250 .250 .250 .250 .250 .250 .250 .250 .250 .250 .250 .312 .312 .312 .312 .312 .312 .340 .340 .340 .340 .340 .340 .340 .400 .400 .400 .400 .400 .400 .400 .625 .625 .625 .625 .625 .625 .625 .625 .625
.156 .156 .156 .250 .250 .250 .250 .250 .250 .375 .375 .375 .375 .375 .375 .500 .500 .500 .500 .500 .500 .500 .500 .500 .500 .500 .750 .750 .750 .750 .750 .750 .750 .875 .875 .875 .875 .875 .875 .875 1.500 1.500 1.500 1.500 1.500 1.500 1.500 1.500 1.500
.375 .875 1.375 .750 1.375 2.375 3.375 3.500 4.500 .750 1.375 2.375 3.375 3.500 4.500 1.250 2.250 2.750 3.250 4.250 1.125 2.125 3.125 3.250 4.000 5.000 1.500 2.500 3.500 3.500 4.000 5.000 7.000 1.625 2.250 2.750 3.500 4.000 5.000 7.000 2.125 1.875 3.375 4.375 5.375 7.375 7.000 10.000 13.000
2-56 2-56 2-56 2-56 2-56 2-56 2-56 2-56 2-56 4-40 4-40 4-40 4-40 4-40 4-40 6-32 6-32 6-32 6-32 6-32 6-32 6-32 6-32 6-32 6-32 6-32 6-32 6-32 6-32 6-32 6-32 6-32 6-32 6-32 6-32 6-32 6-32 6-32 6-32 6-32 10-32 10-32 10-32 10-32 10-32 10-32 10-32 10-32 10-32
2-56 2-56 2-56 2-56 2-56 2-56 2-56 2-56 2-56 4-40 4-40 4-40 4-40 4-40 4-40 4-40 4-40 4-40 4-40 4-40 6-32 6-32 6-32 6-32 6-32 6-32 6-32 6-32 6-32 6-32 6-32 6-32 6-32 6-32 6-32 6-32 6-32 6-32 6-32 6-32 10-32 10-32 10-32 10-32 10-32 10-32 10-32 10-32 10-32
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
*Base holes are tapped and threaded and not counterbored **D Dimension is minimum centered around mean position. Note: DT-66 has six carriage holes, DT-69 has eight and DT-612 has ten.
REGIONAL
STOCK!
SAME-DAY SHIPPING
ESSENTRA gives you the convenience of regional stock for fast delivery and freight savings! 835
LINEAR MOTION SLIDES Crossed Roller Slide Tables
N B
V
M
C
P
A
d
D
S W U
R
Crossed roller slide tables are factory assembled and ready to install. They use crossed roller bearings to provide very precise linear motion with low friction and high support stiffness for the load. A large selection is available for applications including precision instruments, office and communications equipment, surface grinders, tool grinders, assembly fixtures, and anywhere precise linear positioning is required. Precision ground "V" grooved ways and rollers provide high accuracy and load capacity. Withstands force in any direction from alternately crossed rollers at 45 degree angle. Standard pattern for easy installation and interchangeability with other manufacturers slides. Straight line accuracy .0001" inch. Each table consists of a one piece base, a one piece carriage and a pair of linear bearings. Steel type has cold rolled base and carriage with black oxide finish. Ends of carriage contain tapped holes that permit easy attachment of way covers, bellows or other shields to exclude dust and keep the ways clean. Aluminum is available for situations where particulate contamination must be reduced. Aluminum crossed roller slide tables have a gold anodized carriage and black anodized base.
Item No.
Load Capacity Travel (Lbs.)
Steel DT-307 1.969 DT-309 1.181 DT-312 2.362 DT-315 3.543 DT-319 1.181 DT-320 1.772 DT-321 2.362 DT-330 1.969 DT-331 2.953 DT-332 4.134 DT-339 5.118 Aluminum DT-202 1.5 DT-205 3 DT-212 1.5 DT-214 2.5 DT-215 3 DT-221 1 DT-222 2 DT-224 4 DT-225 5 DT-231 2 DT-232 3 DT-242 4 DT-243 6
Base Mounting Holes-Spacing and Dimensions (Counterbored) Lgth.
A
B
C
No. of Holes
88 137 231 319 277 405 484 616 858 1,034 1,914
3.346 1.969 3.740 5.512 2.165 3.150 4.134 3.346 4.921 6.496 8.268
.669 .827 .827 .827 1.102 1.102 1.102 1.378 1.378 1.378 1.772
1.181 1.575 1.575 1.575 2.362 2.362 2.362 3.150 3.150 3.150 3.937
.217 .256 .256 .256 .354 .354 .354 .413 .413 .413 .512
8 4 8 12 4 4 4 4 4 4 6
3.071 1.575 3.346 5.118 1.378 2.362 3.345 2.559 4.134 5.709 7.480
114 198 114 162 198 193 338 545 576 430 600 1,062 1,600
2.559 4.921 2.559 3.740 4.921 2.165 4.134 7.087 8.071 3.346 4.921 6.300 10.240
.590 .590 .827 .827 .827 1.102 1.102 1.102 1.102 1.378 1.378 1.772 1.772
1.181 1.181 1.575 1.575 1.575 2.362 2.362 2.362 2.362 3.150 3.150 3.937 3.937
.160 .160 .256 .256 .256 .354 .354 .354 .354 .413 .413 .512 .512
4 8 4 8 8 4 4 4 8 4 4 4 4
2.165 4.528 2.165 3.346 4.528 1.378 3.345 6.299 7.283 2.557 4.134 5.512 9.449
U
Carriage Holes-Spacing and Dimensions (Threaded)
R
S
D
d
No. of Holes
2.283 — — — 2.165 — 3.397 — — — — — — — — — — — — — — 3.543
.138 .197 .197 .197 .394 .394 .394 .394 .394 .394 .394
.866 1.181 1.181 1.181 1.575 1.575 1.575 2.165 2.165 2.165 2.362
.161 .236 .236 .236 .295 .295 .295 .374 .374 .374 .433
.100 .138 .138 .138 .177 .177 .177 .217 .217 .217 .276
14 4 10 16 2 4 6 2 4 6 6
6 1 4 7
— 3.346 — 2.165 3.346 — — — 3.346 — — — —
.197 .197 .197 .197 .197 .394 .394 .394 .394 .394 .394 .394 .394
.866 .866 1.181 1.181 1.181 1.575 1.575 1.575 1.575 2.165 2.165 2.362 2.362
.198 .198 .241 .241 .241 .328 .328 .328 .328 .328 .328 .406 .406
.1250 .1250 .1495 .1495 .1495 .1970 .1970 .1970 .1970 .1970 .1970 .2660 .2660
6 14 6 10 14 2 6 12 14 2 4 4 8
W
V
— — — — — — — — — — — — —
N
P
Thread
Depth
Pack Qty.
x x x x
1 2 2
.3937 .5906 .5906 .5906 — x .9843 x .9843 — x 1.575 x 1.575 x 1.969
.492 .689 .689 .689 1.083 1.083 1.083 1.673 1.673 1.673 2.165
.394 .591 .591 .591 .984 .984 .984 1.575 1.575 1.575 1.969
M2 M3 M3 M3 M4 M4 M4 M5 M5 M5 M6
.275 .315 .315 .315 .413 .413 .413 .512 .512 .512 .630
1 1 1 1 1 1 1 1 1 1 1
2 6 2 4 6
x x x x x
.689 .689 .689 .689 .689 1.083 1.083 1.083 1.083 1.673 1.673 2.165 2.165
.394 .394 .591 .591 .591 .984 .984 .984 .984 1.575 1.575 1.969 1.969
4-40 4-40 6-32 6-32 6-32 10-32 10-32 10-32 10-32 10-32 10-32 1 ⁄4-20 1 ⁄4-20
.177 .177 .315 .315 .315 .413 .413 .413 .413 .512 .512 .630 .630
1 1 1 1 1 1 1 1 1 1 1 1 1
M
1 2
2 5 6 1 1 3
.5906 .5906 .5906 .5906 .5906 — x .9843 x .9843 x .9843 — x 1.575 x 1.969 x 1.969
Pre-Loaded Ball Slides
W B .22 .70
.50
Moving Top
.75
E D
Ball Retainer
A
Compliant Preload Steel Shim Stationary Slide Base
Rods L
These pre-loaded ball slides provide an acceptable level of accuracy for most linear motion applications (.001"/inch) at a considerably lower cost than more expensive ball slides or crossed roller slides. The compliant slides use a conventional hardened steel rod raceway and balls, but also incorporate an elastomer spine and shock-absorbing back-up gib. This unique combination provides even and continuous preload, while minimizing the effects of impact and shock. This slide can also tolerate contamination and operate over many million cycles without lubrication. Available with either a compliant preload or a hard gib preload. 8-32 thread mounting holes. Compliant Hard Gib Item No.
Item No.
Travel
W
L
A
B
D
E
Preload (Lbs.)
Pack Qty.
BZ-10 BZ-11 BZ-12 BZ-13 BZ-14 BZ-15 BZ-16 BZ-17
BZ-2 BZ-3 BZ-4 BZ-5 BZ-6 BZ-7 BZ-8 BZ-9
1 2 3 2 3 4 5 6
2 2 2 3 3 3 3 3
2 3 4 4 5 6 7 8
1 2 3 3 4 5 6 7
1 1 1 2 2 2 2 2
1.1 1.1 1.1 2.1 2.1 2.1 2.1 2.1
1 1 1 2 2 2 2 2
20 30 40 30 40 50 60 70
1 1 1 1 1 1 1 1
836
LINEAR MOTION SLIDES Dovetail Slides
D
A+/-.001
Travel B +/- .001
C
Dovetail slides are used for work feeders for production milling, positioning fixtures, work holding devices, checking fixtures, shuttle devices, assembly equipment, etc. They are made of continuous cast G2 40,000 psi pearlitic grey iron. This material may be milled, drilled, tapped, etc., for altering or mounting purposes. Tapered gibs are adjusted with a single screw that moves the gib on the taper. This type of gib remains parallel and wear is less as it occurs over the entire surface. Accuracy is .001" in 12" of travel. Lubrication is provided with ball detent oilers.
Item No.
A
B
C
D
Travel
Pack Qty.
DV-110 DV-130 DV-140 DV-100 DV-210 DV-220 DV-230 DV-250 DV-212 DV-310 DV-330 DV-360 DV-390 DV-312 DV-420 DV-430 DV-440 DV-450 DV-490
1.5 1.5 1.5 1.5 2.0 2.0 2.0 2.0 2.0 3.0 3.0 3.0 3.0 3.0 4.0 4.0 4.0 4.0 4.0
1.00 1.00 1.00 1.00 1.25 1.25 1.25 1.25 1.25 1.50 1.50 1.50 1.50 1.50 1.75 1.75 1.75 1.75 1.75
3 5 6 12 4 5 6 8 15 5 7 10 13 16 7 8 9 10 14
2 2 2 2 3 3 3 3 3 4 4 4 4 4 5 5 5 5 5
1 3 4 10 1 2 3 5 12 1 3 6 9 12 2 3 4 5 9
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
SOCKET HEAD CAP SCREWS
& HEX TOOLS Socket Head Cap Screws Pages 766 - 769 Hex Tools Pages 556 - 558
837
RAIL GUIDES & SYSTEMS Mini Rail Self-Lubricating Miniature Systems
Rail and Carriage Assembly
Carriage
H1
S C
F
G
N
E
T
H
D L
K B
B1
H2
M A
Low profile, self-lubricating linear guide system with one piece carriage design. Excellent alternative to linear ball bearing systems. Precision series made from a RC70 ceramic coated rail with self-lubricating FrelonGOLDÂŽ. Commercial series made from a clear anodized rail with FrelonJ. Dampens vibration and tolerates shock loads. Will not rust. No metal-to-metal contact. No balls or rolling elements to trap contamination, skid or damage the rail. Operation is consistent, smooth and quiet. Maintenance free. Used in packaging machines, medical equipment, wash-down and harsh environments, etc. Carriage and rail sold together. Dimensions are in millimeters. Carriages also sold separately below. Rails - Carriages Included
Item No.
Pacific
Running Clearance
PBC-1151 MR7-70 .025 - .051 PBC-1152 MR7-85 .025 - .051 PBC-1153 MR7-100 .025 - .051 PBC-1154 MR7-130 .025 - .051 PBC-1155 MR9-55 .025 - .051 PBC-1157 MR9-95 .025 - .051 PBC-1159 MR9-155 .025 - .051 PBC-1161 MR9-275 .025 - .051 PBC-1162 MR12-120 .025 - .051 PBC-1164 MR12-220 .025 - .051 PBC-1171 MR15-0310 .025 - .051 PBC-1173 MR15-470 .025 - .051 PBC-1174 MR15-670 .025 - .051 PBC-1175 MR20-220 .025 - .051 PBC-1177 MR20-340 .025 - .051 PBC-1178 MR20-460 .025 - .051 PBC-1166 MR12-320-1 .025 - .051 PBC-1168 MR12-470 .025 - .051 PBC-1169 MR15-150 .025 - .051 PBC-1180 MR20-880 .025 - .051
A
B
B1
C
D
E
F
G
H
H1
H2
K
L
M
N
S
T
Rail Length
Max. Static Load Lbs.
Pack Qty.
7 7 7 7 9 9 9 9 12 12 15 15 15 20 20 20 12 12 15 20
8 8 8 8 10 10 10 10 13 13 16 16 16 25 25 25 13 13 16 25
6.2 6.2 6.2 6.2 7.3 7.3 7.3 7.3 8.0 8.0 9.3 9.3 9.3 13.5 13.5 13.5 8.0 8.0 9.3 13.5
17 17 17 17 20 20 20 20 27 27 32 32 32 46 46 46 27 27 32 46
24 24 24 24 30 30 30 30 34 34 42 42 42 62 62 62 34 34 42 62
M2 M2 M2 M2 M3 M3 M3 M3 M3 M3 M3 M3 M3 M4 M4 M4 M3 M3 M3 M4
8 8 8 8 13 13 13 13 15 15 20 20 20 38 38 38 15 15 20 38
12 12 12 12 15 15 15 15 20 20 25 25 25 38 38 38 20 20 25 38
4.2 4.2 4.2 4.2 4.5 4.5 4.5 4.5 6.0 6.0 6.0 6.0 6.0 9.5 9.5 9.5 6.0 6.0 6.0 9.5
2.4 2.4 2.4 2.4 2.6 2.6 2.6 2.6 3.5 3.5 3.5 3.5 3.5 6.0 6.0 6.0 3.5 3.5 3.5 6.0
2.3 2.3 2.3 2.3 3.0 3.0 3.0 3.0 3.5 3.5 4.5 4.5 4.5 8.5 8.5 8.5 3.5 3.5 4.5 8.5
6.2 6.2 6.2 6.2 8.0 8.0 8.0 8.0 10.7 10.7 14.1 14.1 14.1 21.2 21.2 21.2 10.7 10.7 14.1 21.2
1.7 1.7 1.7 1.7 2.4 2.4 2.4 2.4 4.6 4.6 6.3 6.3 6.3 11.2 11.2 11.2 4.6 4.6 6.3 11.2
3.5 3.5 3.5 3.5 3.5 4.5 4.5 4.5 10 10 15 15 15 10 10 10 10 10 15 10
2.3 2.3 2.3 2.3 2.3 2.5 2.5 2.5 3.5 3.5 3.5 3.5 3.5 4.0 4.0 4.0 3.5 3.5 3.5 4.0
5 5 5 5 7.5 7.5 7.5 7.5 6.0 6.0 7.5 7.5 7.5 20 20 20 6.0 6.0 7.5 20
15 15 15 15 20 20 20 20 25 25 40 40 40 60 60 60 25 25 40 60
70 85 100 130 55 95 155 275 120 220 310 470 670 220 340 460 320 470 150 880
165 165 165 165 350 350 350 350 440 440 700 700 700 1,350 1,350 1,350 440 440 700 1,350
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Carriages Only
Item No.
Pacific
Description
Pack Qty.
PBC-1212 PBC-1213 PBC-1214 PBC-1215 PBC-1216
MR7C MR9C MR12C MR15C MR20C
Carriage - to run on 7mm W Base Carriage - to run on 9mm W Base Carriage - to run on 12mm W Base Carriage - to run on 15mm W Base Carriage - to run on 20mm W Base
1 1 1 1 1
838
RAIL GUIDES & SYSTEMS Speedi-Roll Linear Rail Systems C
W
G
U V
L J
E
N
A
T
K Q
R
H F D
B M
P
K
S
Speedi-Roll was developed giving high priority to lightweight construction and ease of installation. Speedi-Roll is a linear guide system with high load carrying capacity, rigidity and torque resistance, consisting of a guide rail and carriage with either four or six rollers. Rollers are lubricated for life, greatly reducing the need for service. The rail is composed of a drawn and anodized aluminum body with hardened steel angle raceways fitted on each side. Base plate is also anodized aluminum with factory-fitted rollers. Elastic elements around the threaded bolts adjust and fix the rollers in the base plate avoiding the risk of mounting error. The units are supplied with a light pre-load to cover a wide variety of applications. Dimensions in millimeters. Carriages and rails are sold separately. Carriages
Permissible Load Lbs.
Item No.
A
C
D
E
F
G
H
J
K
L
Top
Side
Pack Qty.
SKF-115 SKF-125 SKF-135
25.0 35.5 54.3
65 80 120
70 90 100
50 59 90
60 70 70
39.3 45.8 61.3
45 60 65
6.05 12.10 19.40
M5 M8 M10
14 17 21
157 225 562
148 315 562
1 1 1
Item No.
B
M
N
P
Q
R
S
T
U
V
W
Use with Carriage No.
Pack Qty.
SKF-158 SKF-159 SKF-257 SKF-258 SKF-259 SKF-357 SKF-358 SKF-359
3.75 3.75 7.70 7.70 7.70 12.35 12.35 12.35
18 18 23 23 23 36 36 36
24.9 24.9 29.9 29.9 29.9 42.9 42.9 42.9
2 2 4 4 4 7 7 7
17 17 21 21 21 29 29 29
10.8 10.8 14.7 14.7 14.7 22.8 22.8 22.8
9.5 9.5 11.0 11.0 11.0 20.0 20.0 20.0
5.5 5.5 6.5 6.5 6.5 11.0 11.0 11.0
62.5 62.5 125.0 125.0 125.0 250.0 250.0 250.0
31.25 31.25 62.50 62.50 62.50 125.00 125.00 125.00
1,000 2,000 1,000 2,000 3,000 1,000 2,000 3,000
SKF-115 SKF-115 SKF-125 SKF-125 SKF-125 SKF-135 SKF-135 SKF-135
1 1 1 1 1 1 1 1
Rails
MinVee® Miniature Slide System 1.750
90°
1.750 1.308 .875
.709
0.158 VIRTUAL APEX 0.516 0.093
.442 .217 Track Support Spacer (0.097 Spacer)
.567
1.00
1.433
2.000 Qty (4) M4 x 0.7
Length
0.06 0.138
0.153
2 0.25
2 Ø0.156
0.25
MinVee® is a low profile, miniature linear slide system ideal for semi-conductor, laboratory, medical and packaging applications. The non-actuated MinVee® linear slide consists of one or more 6061-T6 anodized aluminum wheel carriage with your choice of DualVee® integral studded wheels (steel/shielded, steel/sealed or polymer/shielded), and double edge track from 6.5 to 36.5 inches. The steel wheel carriage supports loads to 121 pounds while the polymer carriage is capable of up to 15 pounds. MinVee® features stainless steel lubricators, and a patented self-aligning mounting shoulder, reducing installation time and cost. Parts are sold separately. Please specify wheel carriage model and quantity, track (lengths), and number of track support spacers (one per mounting hole). Carriages Item No.
Description
Radial Load LR
Axial Load LA
Pitch Movement MP
Yaw Moment MY
Roll Moment MR
Pack Qty.
WZ-444 WZ-445 WZ-446
Aluminum Carriage, Steel Wheels, Shielded Aluminum Carriage, Steel Wheels, Sealed Aluminum Carriage, Polymer Wheels, Shielded
490N/110.2 lbf 490N/110.2 lbf 65N/14.6 lbf
540N/121.4 lbf 540N/121.4 lbf 66.7N/15 lbf
7.9Nms/69.9 lbf 7.9Nms/69.9 lbf 1.4Nms/12.4 lbf
8.6Nm/76.1 lbf 8.6Nm/76.1 lbf 4.5Nm/39.8 lbf
6.2N/54.9 lbf 6.2N/54.9 lbf 1N/8.8 lbf
1 1 1
Tracks Item No.
Length (Inch)
Track, Steel, Unhardened WZ-448 6.5 WZ-449 12.5 WZ-450 18.5 WZ-451 24.5 WZ-452 30.5 WZ-453 36.5
No. of Holes
4 7 10 13 16 19
Pack Qty.
1 1 1 1 1 1
Item No.
Length (Inch)
Track, Steel, Hardened WZ-454 6.5 WZ-455 12.5 WZ-456 18.5 WZ-457 24.5 WZ-459 36.5
No. of Holes
Pack Qty.
4 7 10 13 19
1 1 1 1 1
839
RAIL GUIDES & SYSTEMS Two Piece Linear Guide Systems
P E
L
D
K
T-Slot
G A M F
O H J
N C B
T-Slot
Two piece linear rail systems use Pacific Bearing's FrelonGold® plain bearing technology. Rail and carriage are made from 6063-T6 aluminum. Rails are ceramic coated to resist corrosion, repel weld spatter and contaminants. Smooth running and dampens vibrations. Guide has slots for T-nuts or bolts. Two component system allows for easier installation than traditional rail systems. Guide and rail are sold together. Item No.
PBC-750 PBC-755 PBC-760 PBC-765 PBC-770
Pacific
D75-12 D75-24 D100-12 D100-24 D125-12
A
2.95 2.95 3.94 3.94 4.92
B
2.0 2.0 2.6 2.6 3.3
C
.75 .75 1.00 1.00 1.25
D
4 4 6 6 6
Bolt Size E 1
⁄4 ⁄4 ⁄16 5 ⁄16 3 ⁄8 1
5
F
G
H
J
K
Bolt Size L
M
N
O
P
Static Load Max. Lbs.
Pack Qty.
1.625 1.625 2.125 2.125 2.625
4.6 4.6 6.1 6.1 7.6
3.5 3.5 4.5 4.5 6.0
3.00 3.00 3.75 3.75 5.25
4.00 4.00 5.25 5.25 6.75
10-32 10-32 1 ⁄4-20 1 ⁄4-20 5 ⁄16-18
2.60 2.60 3.50 3.50 4.33
.810 .810 1.024 1.024 1.300
12 24 12 24 12
2 2 3 3 4
500 500 750 750 1,000
1 1 1 1 1
Crossed Roller Rail Sets
Crossed roller linear rail sets are compact, precision bearings that can support and guide high loads with high accuracy and repeatability, low friction, and low starting force. A complete range of sizes is supplied for use in precision machine tools, measuring instruments and anywhere reciprocating motion with high reliability and long life is required. Each bearing consists of a pair of hardened steel ways containing 90 degree "V" grooves and a row of alternately crossed cylindrical rollers. The hardened steel rollers are captive in a stainless steel cage for easy handling, assembly and permanent alignment. The ways are installed face to face on smooth flat and accurately parallel, coplanar, or perpendicular surfaces. Lubrication required depends on the application ranging from light grease for low speeds less than 50 inches per minute to continuous oil bath or mist at 1,200 inches per minute. Temperature of bearings must not exceed 212 degree Fahrenheit even for short periods, as this will reduce hardness and performance. All are steel. Each set consists of two complete bearings (4 way bars, 2 roller cages, and end stops). F Item No.
No. of Roller
Lgth. L
Travel
Number Holes
Load Lbs.
A
B
C
D
E
Thread
Cap Screw
G
H
K
M
S
Pack Qty.
DT-1011 DT-1012 DT-1013 DT-1015 DT-1051 DT-1071 DT-1072 DT-1074
5 8 11 16 7 8 12 20
1.181 1.772 2.362 3.544 3.150 3.937 5.906 9.843
.709 .945 1.181 1.969 2.283 2.165 3.346 5.906
2 3 4 6 2 2 3 5
66 105 145 211 308 704 1,056 1,760
.473 .473 .473 .473 .866 1.221 1.221 1.221
.236 .236 .236 .236 .433 .591 .591 .591
.217 .217 .217 .217 .402 .559 .559 .559
.079 .079 .079 .079 .158 .236 .236 .236
.0984 .0984 .0984 .0984 .1772 .2360 .2360 .2360
M3 M3 M3 M3 M5 M6 M6 M6
#2 #2 #2 #2 #8 #10 #10 #10
.173 .173 .173 .173 .315 .374 .374 .374
.079 .079 .079 .079 .165 .205 .205 .205
.100 .100 .100 .100 .169 .205 .205 .205
.5910 .5910 .5910 .5910 1.5748 1.9685 1.9685 1.9685
.079 .079 .079 .079 .079 .118 .118 .118
1 1 1 1 1 1 1 1
840
RAIL GUIDES & SYSTEMS Miniature Profile Rail Guides
B C 4-G
F D E
N P
A
J
H T
Q
M
K
S
R L
S
Ideal for precision applications where mounting space is limited. Small and lightweight with high load carrying capacity and high speed linear motion up to 3m/second. Gothic arch grooves at the raceway contacts enable the slide to sustain loads and movements from any direction. Height tolerance is +/- .020 mm. Width tolerance is +/-.025 mm. Free of clearance, no preload for applications with constant load and low friction. All parts are stainless steel or plastic for corrosion resistance. End caps have oil holes for easy relubrication. All dimensions are in millimeters. Item No.
Number of Carriages
L
A
B
C
D
E
F
G
H
J
K
M
N
P
Q
R
S
T
Basic Load Rating (Lbs.)
Pack Qty.
SKF-0 SKF-1 SKF-2 SKF-3 SKF-4 SKF-5 SKF-6 SKF-7 SKF-8 SKF-9 SKF-10 SKF-11 SKF-12 SKF-13 SKF-14 SKF-15 SKF-16 SKF-17 SKF-18 SKF-19 SKF-20 SKF-21 SKF-222 SKF-23 SKF-24 SKF-25 SKF-26 SKF-27 SKF-28 SKF-29
1 1 2 1 2 1 2 2 2 2 1 1 2 1 2 1 2 2 2 2 1 1 2 1 2 1 2 2 2 2
80 110 110 140 140 170 170 200 260 290 110 150 150 190 190 230 230 310 390 470 110 150 150 190 190 230 230 310 390 470
10 10 10 10 10 10 10 10 10 10 13 13 13 13 13 13 13 13 13 13 14 14 14 14 14 14 14 14 14 14
20 20 20 20 20 20 20 20 20 20 27 27 27 27 27 27 27 27 27 27 40 40 40 40 40 40 40 40 40 40
15 15 15 15 15 15 15 15 15 15 20 20 20 20 20 20 20 20 20 20 28 28 28 28 28 28 28 28 28 28
21.5 21.5 21.5 21.5 21.5 21.5 21.5 21.5 21.5 21.5 23 23 23 23 23 23 23 23 23 23 32.5 32.5 32.5 32.5 32.5 32.5 32.5 32.5 32.5 32.5
10 10 10 10 10 10 10 10 10 10 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15
32 32 32 32 32 32 32 32 32 32 36 36 36 36 36 36 36 36 36 36 45.5 45.5 45.5 45.5 45.5 45.5 45.5 45.5 45.5 45.5
M3 x 3 M3 x 3 M3 x 3 M3 x 3 M3 x 3 M3 x 3 M3 x 3 M3 x 3 M3 x 3 M3 x 3 M3 x 3.5 M3 x 3.5 M3 x 3.5 M3 x 3.5 M3 x 3.5 M3 x 3.5 M3 x 3.5 M3 x 3.5 M3 x 3.5 M3 x 3.5 M3 x 3.5 M3 x 3.5 M3 x 3.5 M3 x 3.5 M3 x 3.5 M3 x 3.5 M3 x 3.5 M3 x 3.5 M3 x 3.5 M3 x 3.5
2 2 2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3
6.5 6.5 6.5 6.5 6.5 6.5 6.5 6.5 6.5 6.5 8.8 8.8 8.8 8.8 8.8 8.8 8.8 8.8 8.8 8.8 8.8 8.8 8.8 8.8 8.8 8.8 8.8 8.8 8.8 8.8
9 9 9 9 9 9 9 9 9 9 12 12 12 12 12 12 12 12 12 12 24 24 24 24 24 24 24 24 24 24
3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5
6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 8 8 8 8 8 8 8 8 8 8
3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.8 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5
20 20 20 20 20 20 20 20 20 20 25 25 25 25 25 25 25 25 25 25 40 40 40 40 40 40 40 40 40 40
60 80 80 120 120 140 140 180 240 260 75 125 125 150 150 200 200 275 350 450 80 120 120 160 160 200 200 280 340 440
10 15 15 10 10 15 15 10 10 15 17.5 12.5 12.5 20 20 15 15 17.5 20 10 15 15 15 15 15 15 15 15 15 15
5.5 5.5 5.5 5.5 5.5 5.5 5.5 5.5 5.5 5.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 8 8 8 8 8 8 8 8 8 8
416 416 416 416 416 416 416 416 416 416 573 573 573 573 573 573 573 573 573 573 742 742 742 742 742 742 742 742 742 742
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Note: Basic load rating is the constant load which a system can theoretically accept for a nominal life of 100,000 m of travel with 90% reliability
High Holding Capacity
CLAMPS
Pages 337 - 338
841
LINEAR RAIL SYSTEMS Rails
S3
F2
G1
J1 Y
B1
Item No.
Thomson
Carbon Steel TLM-3109 521H15A+280 TLM-3107 521H15A+160 TLM-3108 521H15A+220 TLM-3111 521H15A+820 TLM-3110 521H15A+460 TLM-3112 521H20A+160 TLM-3114 521H20A+280 TLM-3113 521H20A+220 TLM-3116 521H20A+820 TLM-3115 521H20A+460 TLM-3117 521H20A+1240 TLM-3120 521H25A+280 TLM-3125 521H25A+1600 TLM-3121 521H25A+460 TLM-3119 521H25A+220 TLM-3118 521H25A+160 TLM-3123 521H25A+820 TLM-3124 521H25A+1240 TLM-3122 521H25A+660 TLM-3126 521H30A+280 TLM-3131 521H30A+1640 TLM-3129 521H30A+840 TLM-3130 521H30A+1240 TLM-3132 521H30A+2040 TLM-3128 521H30A+680 TLM-3127 521H30A+440 TLM-3137 521H35A+1240 TLM-3134 521H35A+440 TLM-3135 521H35A+680 TLM-3138 521H35A+1640 TLM-3136 521H35A+840 TLM-3139 521H35A+2040 TLM-3140 521H35A+2520 TLM-3133 521H35A+280 TLM-3141 521H45A+360 TLM-3142 521H45A+570 TLM-3144 521H45A+1200 TLM-3146 521H45A+2040 TLM-3147 521H45A+2460 TLM-3143 521H45A+885 TLM-3145 521H45A+1620 Thin Dense Chrome TLM-3150 521H15AD+280 TLM-3148 521H15AD+160 TLM-3152 521H15AD+820 TLM-3149 521H15AD+220 TLM-3151 521H15AD+460 TLM-3156 521H20AD+460 TLM-3158 521H20AD+1240 TLM-3154 521H20AD+220 TLM-3157 521H20AD+820 TLM-3155 521H20AD+280 TLM-3153 521H20AD+160 TLM-3159 521H25AD+160 TLM-3162 521H25AD+460 TLM-3163 521H25AD+660 TLM-3165 521H25AD+1240 TLM-3166 521H25AD+1600 TLM-3161 521H25AD+280 TLM-3164 521H25AD+820 TLM-3160 521H25AD+220 TLM-3167 521H30AD+280 TLM-3171 521H30AD+1240 TLM-3168 521H30AD+440 TLM-3172 521H30AD+1640 TLM-3169 521H30AD+680 TLM-3170 521H30AD+840 TLM-3173 521H30AD+2040 TLM-3179 521H35AD+1640 TLM-3176 521H35AD+680 TLM-3178 521H35AD+1240 TLM-3181 521H35AD+2520 TLM-3180 521H35AD+2040 TLM-3177 521H35AD+840 TLM-3174 521H35AD+280 TLM-3175 521H35AD+440 TLM-3182 521H45AD+360 TLM-3185 521H45AD+1200 TLM-3186 521H45AD+1620 TLM-3184 521H45AD+885 TLM-3187 521H45AD+2040 TLM-3183 521H45AD+570 TLM-3188 521H45AD+2460
F1
Use with Carriage No.
Size
B1
J1
F1
F2
G1
S3
S3
X
Y
Length
Pack Qty.
TLM-3085, TLM-3091 TLM-3085, TLM-3091 TLM-3085, TLM-3091 TLM-3085, TLM-3091 TLM-3085, TLM-3091 TLM-3086, TLM-3092 TLM-3086, TLM-3092 TLM-3086, TLM-3092 TLM-3086, TLM-3092 TLM-3086, TLM-3092 TLM-3086, TLM-3092 TLM-3087, TLM-3093 TLM-3087, TLM-3093 TLM-3087, TLM-3093 TLM-3087, TLM-3093 TLM-3087, TLM-3093 TLM-3087, TLM-3093 TLM-3087, TLM-3093 TLM-3087, TLM-3093 TLM-3088, TLM-3094 TLM-3088, TLM-3094 TLM-3088, TLM-3094 TLM-3088, TLM-3094 TLM-3088, TLM-3094 TLM-3088, TLM-3094 TLM-3088, TLM-3094 TLM-3190, TLM-3191 TLM-3190, TLM-3191 TLM-3190, TLM-3191 TLM-3190, TLM-3191 TLM-3190, TLM-3191 TLM-3190, TLM-3191 TLM-3190, TLM-3191 TLM-3190, TLM-3191 TLM-3089 TLM-3089 TLM-3089 TLM-3089 TLM-3089 TLM-3089 TLM-3089
15 15 15 15 15 20 20 20 20 20 20 25 25 25 25 25 25 25 25 30 30 30 30 30 30 30 35 35 35 35 35 35 35 35 45 45 45 45 45 45 45
15 15 15 15 15 20 20 20 20 20 20 23 23 23 23 23 23 23 23 28 28 28 28 28 28 28 34 34 34 34 34 34 34 34 45 45 45 45 45 45 45
15.7 15.7 15.7 15.7 15.7 19 19 19 19 19 19 22.7 22.7 22.7 22.7 22.7 22.7 22.7 22.7 26 26 26 26 26 26 26 29.5 29.5 29.5 29.5 29.5 29.5 29.5 29.5 37 37 37 37 37 37 37
4.5 4.5 4.5 4.5 4.5 5.8 5.8 5.8 5.8 5.8 5.8 7 7 7 7 7 7 7 7 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 14 14 14 14 14 14 14
8 8 8 8 8 10 10 10 10 10 10 11 11 11 11 11 11 11 11 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 20 20 20 20 20 20 20
4.5 4.5 4.5 4.5 4.5 6.5 6.5 6.5 6.5 6.5 6.5 8 8 8 8 8 8 8 8 10 10 10 10 10 10 10 12 12 12 12 12 12 12 12 15 15 15 15 15 15 15
M4 M4 M4 M4 M4 M5 M5 M5 M5 M5 M5 M6 M6 M6 M6 M6 M6 M6 M6 M7 M7 M7 M7 M7 M7 M7 M8 M8 M8 M8 M8 M8 M8 M8 M12 M12 M12 M12 M12 M12 M12
M4 M4 M4 M4 M4 M5 M5 M5 M5 M5 M5 M6 M6 M6 M6 M6 M6 M6 M6 M7 M7 M7 M7 M7 M7 M7 M8 M8 M8 M8 M8 M8 M8 M8 M12 M12 M12 M12 M12 M12 M12
60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80 105 105 105 105 105 105 105
20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 22.5 22.5 22.5 22.5 22.5 22.5
280 160 220 820 460 160 280 220 820 460 1,240 280 1,600 460 220 160 820 1,240 660 280 1,640 840 1,240 2,040 680 440 1,240 440 680 1,640 840 2,040 2,520 280 360 570 1,200 2,040 2,460 885 1,620
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
TLM-3096, TLM-3102 TLM-3096, TLM-3102 TLM-3096, TLM-3102 TLM-3096, TLM-3102 TLM-3096, TLM-3102 TLM-3079, TLM-3103 TLM-3079, TLM-3103 TLM-3079, TLM-3103 TLM-3079, TLM-3103 TLM-3079, TLM-3103 TLM-3079, TLM-3103 TLM-3098, TLM-3104 TLM-3098, TLM-3104 TLM-3098, TLM-3104 TLM-3098, TLM-3104 TLM-3098, TLM-3104 TLM-3098, TLM-3104 TLM-3098, TLM-3104 TLM-3098, TLM-3104 TLM-3099, TLM-3105 TLM-3099, TLM-3105 TLM-3099, TLM-3105 TLM-3099, TLM-3105 TLM-3099, TLM-3105 TLM-3099, TLM-3105 TLM-3099, TLM-3105 TLM-3192, TLM-3193 TLM-3192, TLM-3193 TLM-3192, TLM-3193 TLM-3192, TLM-3193 TLM-3192, TLM-3193 TLM-3192, TLM-3193 TLM-3192, TLM-3193 TLM-3192, TLM-3193 TLM-3100 TLM-3100 TLM-3100 TLM-3100 TLM-3100 TLM-3100 TLM-3100
15 15 15 15 15 20 20 20 20 20 20 25 25 25 25 25 25 25 25 30 30 30 30 30 30 30 35 35 35 35 35 35 35 35 45 45 45 45 45 45 45
15 15 15 15 15 20 20 20 20 20 20 23 23 23 23 23 23 23 23 28 28 28 28 28 28 28 34 34 34 34 34 34 34 34 45 45 45 45 45 45 45
15.7 15.7 15.7 15.7 15.7 19 19 19 19 19 19 22.7 22.7 22.7 22.7 22.7 22.7 22.7 22.7 26 26 26 26 26 26 26 29.5 29.5 29.5 29.5 29.5 29.5 29.5 29.5 37 37 37 37 37 37 37
4.5 4.5 4.5 4.5 4.5 5.8 5.8 5.8 5.8 5.8 5.8 7 7 7 7 7 7 7 7 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 14 14 14 14 14 14 14
8 8 8 8 8 10 10 10 10 10 10 11 11 11 11 11 11 11 11 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 20 20 20 20 20 20 20
4.5 4.5 4.5 4.5 4.5 6.5 6.5 6.5 6.5 6.5 6.5 8 8 8 8 8 8 8 8 10 10 10 10 10 10 10 12 12 12 12 12 12 12 12 15 15 15 15 15 15 15
M4 M4 M4 M4 M4 M5 M5 M5 M5 M5 M5 M6 M6 M6 M6 M6 M6 M6 M6 M7 M7 M7 M7 M7 M7 M7 M8 M8 M8 M8 M8 M8 M8 M8 M12 M12 M12 M12 M12 M12 M12
M4 M4 M4 M4 M4 M5 M5 M5 M5 M5 M5 M6 M6 M6 M6 M6 M6 M6 M6 M7 M7 M7 M7 M7 M7 M7 M8 M8 M8 M8 M8 M8 M8 M8 M12 M12 M12 M12 M12 M12 M12
60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 60 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80 105 105 105 105 105 105 105
20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 22.5 22.5 22.5 22.5 22.5 22.5
280 160 820 220 460 460 1,240 220 820 280 160 160 460 660 1,240 1,600 280 820 220 280 1,240 440 1,640 680 840 2,040 1,640 680 1,240 2,520 2,040 840 280 440 360 1,200 1,620 885 2,040 570 2,460
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Note: All dimensions in mm unless otherwise specified
842
X
LINEAR RAIL SYSTEMS The Thomson 500 Series Ball Profile Rail Linear Guides provides long life, exceptional rigidity, high dynamic and static load capacities in all direction; accommodates high moment loads; and maintains a high running accuracy. These properties result in improved machine accuracies and rigidity resulting in reduced vibration extending machine and tool life. This has a direct effect on operational efficiency resulting in cost savings for the user. These units are a drop-in replacement for existing linear ball guide systems. The rails are subjected to multiple straightening processes during and after grinding of the ball paths to ensure straight accurate rails. A patented, custom insert molded recirculation path that has an optimized geometric shape and minimal transitions ensures smooth and quiet operation in both low and high-speed operation. Built-in undercarriage, low-drag longitudinal seals protect the balls and ball path from contamination. These longitudinal seals are an added protection to increase the life and overall performance. A special trapezoidal profile maximizes the carriage cross section, resulting in the highest possible rigidity. All ball bearing raceways are hardened to a minimum of 60 Rockwell C. The carriages are available in standard and narrow profiles, as "clearance" units, which are the most commonly specified type in the market today. Carriages and rails are available in carbon steel or thin dense, chrome-coated carbon steel and are sold separately. Carriages B
N J
A B2 S2
B1 L
L1
F2
S3 G1
J1 Y
X
F1
B N G J
A
B1
B2
Standard Item No.
Load Rating (N) Thomson
Size
Carbon Steel - Standard TLM-3085 511H15A0 15 TLM-3086 511H20A0 20 TLM-3087 511H25A0 25 TLM-3088 511H30A0 30 TLM-3190 511H35A0 35 TLM-3089 511H45A0 45 Carbon Steel - Narrow TLM-3091 511H15C0 15 TLM-3092 511H20C0 20 TLM-3093 511H25C0 25 TLM-3094 511H30C0 30 TLM-3191 511H35C0 35 Thin Dense Chrome - Standard TLM-3096 511H15A0D 15 TLM-3097 511H20A0D 20 TLM-3098 511H25A0D 25 TLM-3099 511H30A0D 30 TLM-3192 511H35A0D 35 TLM-3100 511H45A0D 45 Thin Dense Chrome - Narrow TLM-3102 511H15C0D 15 TLM-3103 511H20C0D 20 TLM-3104 511H25C0D 25 TLM-3105 511H30C0D 30 TLM-3193 511H35C0D 35
A
B
B1
B2
N
J
G
L
L1
S2
Dynamic
Static
Pack Qty.
24 30 36 42 48 60
47 63 70 90 100 120
15 20 25 30 35 45
16 21.5 23.5 31 33 37.5
38 53 57 72 82 100
20.2 25.5 30.5 35.9 41 50.8
7 8 9 12 12 15
59.8 75.5 89.3 103 118 145
30 40 45 52 62 80
M5 M6 M8 M10 M10 M12
9,000 14,400 21,100 29,200 38,700 61,900
19,600 31,400 46,100 63,700 84,400 134,800
1 1 1 1 1 1
24 30 36 42 48
34 44 48 60 70
15 20 25 30 35
9.5 12 12.5 16 18
26 32 45 40 50
20.2 25.5 30.5 35.9 41
5 7 9 11 12
59.8 75.5 89.3 103 118
26 36 45 40 50
M4 M5 M6 M8 M8
9,000 14400 21,100 29,200 38,700
19,600 31,400 46,100 63,700 84,400
1 1 1 1 1
24 30 36 42 48 60
47 63 70 90 100 120
15 20 25 30 35 45
16 21.5 23.5 31 33 37.5
38 53 57 72 82 100
20.2 25.5 30.5 35.9 41 50.8
7 8 9 12 12 15
59.8 75.5 89.3 103 118 145
30 40 45 52 62 80
M5 M6 M8 M10 M10 M12
9,000 14,400 21,100 29,200 38,700 61,900
19,600 31,400 46,100 63,700 84,400 134,800
1 1 1 1 1 1
24 30 36 42 48
34 44 48 60 70
15 20 25 30 35
9.5 12 12.5 16 18
26 32 45 40 50
20.2 25.5 30.5 35.9 41
5 7 9 11 12
59.8 75.5 89.3 103 118
26 36 45 40 50
M4 M5 M6 M8 M8
9,000 14,400 21,100 29,200 38,700
19,600 31,400 46,100 63,700 84,400
1 1 1 1 1
Note: Dynamic load ratings are based on 100km of travel to compare to manufactures using 50km divide value for 50km by 1.26 Note: All dimensions in mm unless otherwise specified
CLAMPING SYSTEMS
Pages 372 - 373
843
LINEAR RAIL SYSTEMS Profile rail guides are used in the production of linear guidance systems with unlimited travel. They consist of a profile rail with four precision ground raceways and a slide unit with four ball circulation paths. The square configuration of the raceways results in a guidance system with good rigidity, capable of withstanding moment loads in all directions. The load carrying capacity is equal in all four directions. Grease nipples are provided. Low vibration and low noise. The units are supplied with a light pre-loaded to cover a wide variety of applications. Case hardened steel. Lubricated with a lithium based grease. Dimensions are in millimeters. Carriages and rails are sold separately.
Carriages
D E
6-M
G H J
A
Q
L
P
B
C
N S
R
T
S U
Flanged with Lube Reservoir Load Rating (Lbs.)
Item No.
A
C
D
E
G
H
J
L
M
Dynamic
Static
Pack Qty.
SKF-361T SKF-362T SKF-363T SKF-364T SKF-365T
24 30 36 42 48
16.0 21.5 23.5 31.0 33.0
47 63 70 90 100
38 53 57 72 82
62.0 72.0 82.0 100.4 114.0
40.0 50.0 57.0 67.4 77.0
30 40 45 52 62
8.0 9.0 12.0 11.5 13.0
M5 x 0.8 M6 x 1 M8 x 1.25 M10 x 1.5 M10 x 1.5
1,752 4,225 5,124 7,124 9,415
3,034 5,483 6,831 9,281 12,135
1 1 1 1 1
Flanged Long with Lube Reservoir Load Rating (Lbs.)
Item No.
A
C
D
E
G
H
J
L
M
Dynamic
Static
Pack Qty.
SKF-502T SKF-503T SKF-504T SKF-505T SKF-506T
30 36 42 48 60
21.5 23.5 31.0 33.0 37.5
63 70 90 100 120
53 57 72 82 100
88.2 104.1 125.4 142.5 167.0
66.2 79.1 92.4 105.5 128.0
40 45 52 62 80
9.0 12 11.5 13.0 15.0
M6 x 1 M8 x 1.25 M10 x 1.5 M10 x 1.5 M12 x 1.75
5,483 6,832 8,989 12,494 20,315
7,910 10,225 12,989 18,202 28,876
1 1 1 1 1
Narrow with Lube Reservoir Load Rating (Lbs.)
Item No.
A
C
D
E
G
H
J
L
M
Dynamic
Static
Pack Qty.
SKF-507T SKF-508T SKF-509T SKF-510T SKF-511T SKF-512T
28 30 40 45 55 70
9.5 12.0 12.5 16.0 18.0 20.5
34 44 48 60 70 86
26 32 35 40 50 60
62.0 72.0 82.0 100.4 114.0 135.0
40.0 50.0 57.0 67.4 77.0 96.0
26 36 35 40 50 60
7.5 6.5 10.0 11.2 17.0 20.5
M4 x 0.7 M5 x 0.8 M6 x 1 M8 x 1 M8 x 1.25 M10 x 1.5
1,753 4,225 5,124 7,124 9,415 15,303
3,034 5,483 6,831 9,281 12,135 19,258
1 1 1 1 1 1
Narrow Long with Lube Reservoir Load Rating (Lbs.)
Item No.
A
C
D
E
G
H
J
L
M
Dynamic
Static
Pack Qty.
SKF-513T SKF-514T SKF-515T SKF-516T
40 45 55 70
12.5 16.0 18.0 20.5
48 60 70 86
35 40 50 60
104.1 125.4 142.5 167.0
79.1 92.4 105.5 128.0
50 60 72 80
10.0 11.2 17.0 20.5
M6 x 1 M8 x 1.25 M8 x 1.25 M10 x 1.5
6,832 8,989 12,494 20,315
10,225 12,989 18,202 28,876
1 1 1 1
Rails Item No.
Use with Carriage No.
B
N
P
Q
R
S
T
U
Pack Qty.
SKF-366T SKF-367T SKF-368T SKF-369T SKF-370T SKF-371T SKF-372T SKF-374T SKF-375T SKF-376T SKF-377T SKF-378T SKF-379T SKF-380T SKF-381T SKF-382T SKF-383T SKF-384T SKF-385T SKF-386T SKF-387T
SKF-361T, SKF-507T SKF-361T, SKF-507T SKF-361T, SKF-507T SKF-362T, SKF-502T, SKF-508T SKF-362T, SKF-502T, SKF-508T SKF-362T, SKF-502T, SKF-508T SKF-363T, SKF-503T, SKF-509T, SKF-513T SKF-363T, SKF-503T, SKF-509T, SKF-513T SKF-363T, SKF-503T, SKF-509T, SKF-513T SKF-364T, SKF-504T, SKF-510T, SKF-514T SKF-364T, SKF-504T, SKF-510T, SKF-514T SKF-364T, SKF-504T, SKF-510T, SKF-514T SKF-364T, SKF-504T, SKF-510T, SKF-514T SKF-364T, SKF-504T, SKF-510T, SKF-514T SKF-364T, SKF-504T, SKF-510T, SKF-514T SKF-365T, SKF-505T, SKF-511T, SKF-515T SKF-365T, SKF-505T, SKF-511T, SKF-515T SKF-365T, SKF-505T, SKF-511T, SKF-515T SKF-365T, SKF-505T, SKF-511T, SKF-515T SKF-365T, SKF-505T, SKF-511T, SKF-515T SKF-365T, SKF-505T, SKF-511T, SKF-515T
4.6 4.6 4.6 5.0 5.0 5.0 7.0 7.0 7.0 9.0 9.0 9.0 9.0 9.0 9.0 9.5 9.5 9.5 9.5 9.5 9.5
15 15 15 20 20 20 23 23 23 28 28 28 28 28 28 34 34 34 34 34 34
14 14 14 18 18 18 22 22 22 26 26 26 26 26 26 29 29 29 29 29 29
7.5 7.5 7.5 9.5 9.5 9.5 11.0 11.0 11.0 14.0 14.0 14.0 14.0 14.0 14.0 14.0 14.0 14.0 14.0 14.0 14.0
4.5 4.5 4.5 6.0 6.0 6.0 7.0 7.0 7.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0 9.0
20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20
60 60 60 60 60 60 60 60 60 80 80 80 80 80 80 80 80 80 80 80 80
220 460 820 280 640 1,000 340 1,240 1,600 440 760 1,240 1,640 2,040 2,520 440 760 1,240 1,640 2,040 2,520
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
844
REDI-RAIL™ LINEAR GUIDE SYSTEMS These easy-to-use systems can be installed into many applications including packaging, material handling, automation and assembly equipment. They consist of a roller guide and rail. The roller guide is made from 6061-T6 aluminum base with three rollers. The rollers are made from 52100 hardened steel and are lubricated and sealed. The pre-load is easily adjusted to meet your requirements. The rail is made from 6061-T6 aluminum with hardened and ground steel raceways inserted for the rollers to run on. Guides and rails are sold separately. Metric dimensions are in millimeters. The metric roller guides have a felt seal to keep contamination clear of rollers.
Roller Guides
Rails
D G
A B
T
S B
E Y-Tapped Mounting Holes X-Rail Mounting Holes for
F
Metric Button Head Cap Screws
Roller Guides
Item No.
Inch PBC-605 PBC-610 Metric PBC-625 PBC-630 PBC-635
Pacific
Fits Rail Width B
A
D
E
G
RRS14 RRS18
1.32 1.91
.918 1.125
3.25 4.50
1.25 1.50
1.250 1.625
RRS30 RRS45 RRS65
30 45 65
28 33 42
86 116 161
25.4 38.1 50.8
26 36 52
Y
Pack Qty.
⁄4-28 ⁄16-24
1 1
M5 x .80 M8 x 1.25 M8 x 1.25
1 1 1
1 5
Rails
Item No.
Inch PBC-650 PBC-655 PBC-660 PBC-665 PBC-670 PBC-675 Metric PBC-700 PBC-705 PBC-710 PBC-715 PBC-720 PBC-725 PBC-730 PBC-735 PBC-740
Pacific
Width B
Lgth.
F
S
T
X
No. of Holes
Pack Qty.
RR14-12 RR14-24 RR14-36 RR18-12 RR18-24 RR18-36
1.32 1.32 1.32 1.91 1.91 1.91
12 24 36 12 24 36
.60 .60 .60 .75 .75 .75
.75 1.50 .50 .75 1.50 .50
3.50 3.50 3.50 3.50 3.50 3.50
#10 #10 #10 1 ⁄4 1 ⁄4 1 ⁄4
4 7 11 4 7 11
1 1 1 1 1 1
RR30-480 RR30-720 RR30-960 RR45-480 RR45-720 RR45-960 RR65-480 RR65-720 RR65-960
30 30 30 45 45 45 65 65 65
480 720 960 480 720 960 480 720 960
16.00 16.00 16.00 20.50 20.50 20.50 27.00 27.00 27.00
30 30 30 30 30 30 40 40 40
60 60 60 60 60 60 80 80 80
M5 M5 M5 M6 M6 M6 M6 M6 M6
8 12 16 8 12 16 6 9 12
1 1 1 1 1 1 1 1 1
845
LINEAR GUIDE SYSTEMS & COMPONENTS
A B .43 + .05 - .12
B .43 + .05 - .12 E F
D
C D
E
C
D
F G ØH
G ØH
Concentric Stud
Eccentric Stud MadeWell Crown Roller
Eccentric Stud
DualVee® integral guide wheels feature a one-piece bushing or stud shaft with a machined inner bearing race in lieu of a two-piece assembly, providing a lower procurement and installation cost. The unique one-piece design provides a lower profile and increased rigidity (up to 84% less deflection), less tolerance stack up, greater torque capability, and external adjustment. Integral wheels are available in 52100 carbon steel and polymer overmoulded. Like original DualVee® wheels, integral wheels are ideal for a wide array of applications from the clean room to the saw mill. These rugged, yet economical, guide wheels provide smooth, quiet motion at speeds up to 5.5 m/s and acceleration to 5 g's. The recirculating elements are self-contained and isolated from the environment; rolling contact between the wheel and track sweeps debris aside, making it ideal for use in contaminated environments. Track is easily joined for long length systems.
Integral Studded DualVee® Wheels Steel
See facing page for track. Concentric Shielded
Eccentric Sealed
Shielded
Item No.
Stud Thread
Item No.
Stud Thread
WZ-400 WZ-401 WZ-402 WZ-403 WZ-404
M6 x 1.0 M8 x 1.25 M10 x 1.5 M12 x 1.75 M14 x 2.0
WZ-405 WZ-406 WZ-407 WZ-408 WZ-409
M6 x 1.0 M8 x 1.25 M10 x 1.5 M12 x 1.75 M14 x 2.0
Item No.
Sealed Item No.
Stud Thread
WZ-410 M5 x .8 WZ-411 M6 x 1.0 WZ-412 M8 x 1.25 WZ-413 M10 x 1.5 WZ-414 M12 x 1.75
Stud Thread Size
WZ-415 M5 x .8 WZ-416 M6 x 1.0 WZ-417 M8 x 1.25 WZ-418 M10 x 1.5 WZ-419 M12 x 1.75
0 1 2 3 4
A
B
D
E
F
G
H
Radial Load (lbf)
Pack Qty.
7.62 8.10 11.38 15.11 19.00
16.95 19.33 26.57 36.68 44.89
6.15 7.30 9.63 13.63 16.36
.46 .61 .76 1.50 2.01
14.83 19.58 30.73 45.80 59.94
146 274 596 1,326 2,181
1 1 1 1 1
C
11 5.56 2.16 12 6.30 2.16 14 9.53 2.79 19 10.72 4.32 22 12.70 4.50
Polymer
Concentric
Eccentric
Shielded
Shielded
Item No.
Stud Thread
WZ-420 WZ-421 WZ-422
M6 x 1.0 M8 x 1.25 M10 x 1.5
Item No.
Stud Thread
WZ-423 M5 x .8 WZ-424 M6 x 1.0 WZ-425 M8 x 1.25
Size
A
B
C
D
E
F
G
H
Radial Load (lbf)
Pack Qty.
0 1 2
11 12 14
5.56 6.30 9.53
2.16 2.16 2.79
7.62 8.10 11.38
16.95 19.33 26.57
6.15 7.30 9.63
.81 .84 .97
14.83 19.58 30.73
6 12 16
1 1 1
L
O
CR Series 1
A F
/2 F
B
G
E
C
K J D
H
M
P
N
Carriage Assembly
Channel
CR Series (composite stainless steel) features heat treated stainless steel track mounted to an extruded aluminum base, and stainless steel wheels with sealed bearings in sizes 1, 2 and 3. CR Series offers corrosion resistance for load requirements up to 5,739N, speeds to 5.5 m/s and acceleration to 5 g's. Vee style only. Carriage Assemblies
Item No.
For use with Channel Sizes
A
WZ-490 WZ-491 WZ-492
1 2 3
100 125 170
846
B
Composite Channels
C
D
38 28.0 10.1 55 36.0 13.7 80 50.0 19.6
E (Socket Size)
F
G
Radial Load (N)
Pack Qty.
7 13 17
40 45 60
M6 x 1.0 M8 x 1.25 M10 x 1.5
1,111 2,671 5,739
1 1 1
Item No.
Channel Size
H
J
K
L
M
WZ-493 WZ-494 WZ-495 WZ-496 WZ-497 WZ-499 WZ-498 WZ-500 WZ-501
1 1 1 2 2 2 2 3 3
17.7 17.7 17.7 21.5 21.5 21.5 21.5 29.5 29.5
5.9 5.9 5.9 7.3 7.3 7.3 7.3 9.0 9.0
40 40 40 60 60 60 60 85 85
290 690 390 240 690 3,390 1,140 1,415 3,415
45.0 45.0 45.0 45.0 45.0 45.0 45.0 82.5 82.5
N
18.8 18.8 18.8 25.4 25.4 25.4 25.4 28.6 28.6
x x x x x x x x x
2 2 2 3 3 3 3 5 5
O
P
Pack Qty.
6.9 6.9 6.9 8.8 8.8 8.8 8.8 10.5 10.5
100 100 100 150 150 150 150 250 250
1 1 1 1 1 1 1 1 1
DUALVEE® GUIDE SYSTEMS N X
B
Wheels
90°
N K
K D
S
Track
S
L
L H
H
A C
Eccentric Bushing
Concentric Bushing
90° A K G J
90°
Bushings
E
H F
B
C
D
C
Wheels
C
C
B
Track
®
The DualVee product line offers customers easy to use and easy to install guide wheel components and assemblies. DualVee® components are ideal for a wide array of applications, from the clean room to the saw mill. These rugged, yet economical, guide wheels provide smooth, quiet motion at speeds up to 5.5 m/s and acceleration to 5 g's. The recirculating elements are self-contained and isolated from the environment; rolling contact between the wheel and track, sweeps debris aside making it ideal for use in contaminated environments. Track is easily joined for long length systems. Standard wheels are available in 52100 carbon steel or 440C stainless steel. Eccentric or concentric bushings are 303 stainless or nickel plated carbon steel. Alternatively, integral one-piece wheels can be selected for lower cost and ease of installation. Matching track is cold formed and hardened and polished on the running surfaces. Track is available in AISI 1045 steel hardened to 53 Rc or AISI 420 stainless hardened to 40 Rc. All parts are sold separately. Wheels
Steel Shielded Steel Sealed Stainless Sealed Item No.
Item No.
Item No.
Size
A
B
C
D
Static Radial Capacity Lbs.
Pack Qty.
WZ-11 WZ-12 WZ-13 WZ-14 WZ-90
WZ-21 WZ-22 WZ-23 WZ-24 —
WZ-31 WZ-32 WZ-33 WZ-34 WZ-99
1 2 3 4 4XL
.77 1.21 1.80 2.36 2.97
.310 .437 .625 .750 1.000
.1875 .3750 .4724 .5906 .8661
.313 .500 .750 1.000 1.250
274 596 1,326 2,191 3,215
1 1 1 1 1
Bushings
Eccentric Item No.
Concentric Item No.
X
WZ-51 WZ-52 WZ-53 WZ-54
WZ-95 WZ-96 WZ-97 WZ-98
.012 .024 .042 .060
Size
H
1 2 3 4
K
.550 .706 .990 1.177
L
Screw Size N
S
Pack Qty.
#6 1 ⁄4 ⁄16 3 ⁄8
.250 .281 .375 .437
1 1 1 1
7
.1873 .3748 .4722 .5904
⁄16 ⁄ ⁄ ⁄
9
16 3 4 7 8
5
Note: Mounting information assumes a central position for bushing allowing an adjustment from +X to -X.
Track
Steel
Stainless
Item No.
Item No.
Size
No. of Holes
+/-.005 A
B
C
+/-.005 D
E
F
G
H
J
K
Pack Qty.
WZ-10 WZ-15 WZ-16 WZ-17 WZ-18 WZ-19 WZ-30 WZ-35 WZ-36 WZ-37 WZ-38 WZ-39 WZ-50 WZ-55 WZ-56 WZ-57 WZ-58 WZ-59 WZ-70 WZ-75 WZ-76 WZ-77 WZ-78 WZ-79
WZ-20 WZ-25 WZ-26 WZ-27 WZ-28 WZ-29 — WZ-45 WZ-46 WZ-47 WZ-48 WZ-49 WZ-60 WZ-65 WZ-66 WZ-67 WZ-68 WZ-69 WZ-80 WZ-85 WZ-86 WZ-87 WZ-88 —
1 1 1 1 1 1 2 2 2 2 2 2 3 3 3 3 3 3 4 4 4 4 4 4
7 13 19 25 31 37 5 9 13 17 21 25 5 9 13 17 21 25 4 7 10 13 16 19
12.50 24.50 36.50 48.50 60.50 72.50 12.63 24.63 36.63 48.63 60.63 72.63 12.75 24.75 36.75 48.75 60.75 72.75 13.00 25.00 37.00 49.00 61.00 73.00
.250 .250 .250 .250 .250 .250 .315 .315 .315 .315 .315 .315 .375 .375 .375 .375 .375 .375 .500 .500 .500 .500 .500 .500
2 2 2 2 2 2 3 3 3 3 3 3 3 3 3 3 3 3 4 4 4 4 4 4
.156 .156 .156 .156 .156 .156 .203 .203 .203 .203 .203 .203 .281 .281 .281 .281 .281 .281 .344 .344 .344 .344 .344 .344
.156 .156 .156 .156 .156 .156 .219 .219 .219 .219 .219 .219 .313 .313 .313 .313 .313 .313 .375 .375 .375 .375 .375 .375
.187 .187 .187 .187 .187 .187 .250 .250 .250 .250 .250 .250 .343 .343 .343 .343 .343 .343 .437 .437 .437 .437 .437 .437
.031 .031 .031 .031 .031 .031 .031 .031 .031 .031 .031 .031 .062 .062 .062 .062 .062 .062 .093 .093 .093 .093 .093 .093
.437 .437 .437 .437 .437 .437 .625 .625 .625 .625 .625 .625 .875 .875 .875 .875 .875 .875 1.062 1.062 1.062 1.062 1.062 1.062
.062 .062 .062 .062 .062 .062 .093 .093 .093 .093 .093 .093 .109 .109 .109 .109 .109 .109 .125 .125 .125 .125 .125 .125
.125 .125 .125 .125 .125 .125 .187 .187 .187 .187 .187 .187 .250 .250 .250 .250 .250 .250 .312 .312 .312 .312 .312 .312
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
847
SUPER SMART BALL BUSHING® BEARINGS Closed Pillow Blocks Single -Twin Metric
N H1
E
B
H A1
Item No.
Dia.
A
B
Metric - Single Closed Type Pillow Block TLM-3013 8 35 32 TLM-3014 12 43 39 TLM-3015 16 53 43 TLM-3016 20 60 54 TLM-3017 25 78 67 TLM-3018 30 87 79 TLM-3019 40 108 91 Metric - Twin Closed Type Pillow Block TLM-3194 8 35 62 TLM-3020 12 43 76 TLM-3021 16 53 84 TLM-3022 20 60 104 TLM-3023 25 78 130 TLM-3024 30 87 152 TLM-3025 40 108 176
ACCESS FOR LUBRICATION M6 X1
E1 A
N2
+/-.020 A1
+/-.1 E
+/-.1 E1
N
N2
+/-.020 H
H1
Dynamic Load (lbf)
Pack Qty.
17.5 21.5 26.5 30 39 43.5 54
20 23 26 32 40 45 58
25 32 40 45 60 68 86
3.3 4.3 5.3 6.6 8.4 8.4 10.5
M4 M5 M6 M8 M10 M10 M12
15 18 22 25 30 35 45
28 35 42 50 60 71 91
310 650 2,200 4,000 6,700 8,300 13,700
1 1 1 1 1 1 1
17.5 21.5 26.5 30 39 43.5 54
50 56 64 76 94 106 124
25 32 40 45 60 68 86
3.3 4.3 5.3 6.6 8.4 8.4 10.5
M4 M5 M6 M8 M10 M10 M12
15 18 22 25 30 35 45
28 35 42 50 60 71 91
500 1,060 4,400 8,000 13,400 16,600 27,400
1 1 1 1 1 1 1
Open Pillow Blocks Single - Twin Metric g N H1
E
B
H A1 E1 A
N2
Item No.
Dia.
A
B
Metric - Single Closed Type Pillow Block TLM-3027 12 43 39 TLM-3028 16 53 43 TLM-3029 20 60 54 TLM-3030 25 78 67 TLM-3031 30 87 79 TLM-3032 40 108 91 Metric - Twin Closed Type Pillow Block TLM-3033 12 43 76 TLM-3034 16 53 84 TLM-3035 20 60 104 TLM-3036 25 78 130 TLM-3038 40 108 176 TLM-3037 30 87 152
ACCESS FOR LUBRICATION M6 X 1
+/-.020 A1
+/-.1 E
+/-.1 E1
N
N2
+/-.020 H
H1
Angle Degree g
Dynamic Load (lbf)
Pack Qty.
21.5 26.5 30 39 43.5 54
23 26 32 40 45 58
32 40 45 60 68 86
4.3 5.3 6.6 8.4 8.4 10.5
M5 M6 M8 M10 M10 M12
18 22 25 30 35 45
28 35 42 51 60 77
70 70 50 60 55 54
750 2,200 4,000 6,700 8,300 13,700
1 1 1 1 1 1
21.5 26.5 30 39 54 43.5
56 64 76 94 124 106
32 40 45 60 86 68
4.3 5.3 6.6 8.4 10.5 8.4
M5 M6 M8 M10 M12 M10
18 22 25 30 45 35
28 35 41 50 77 60
70 70 50 60 54 55
1,220 4,400 8,000 13,400 27,400 16,600
1 1 1 1 1 1
60 Case® LinearRace® Steel Metric
Thomson's 60 Case® LinearRace® shafts are precision ground to exacting standards for superior linear bearing performance and life. Case hardened to 60-65C. Roundness is 80 millionth of an inch. Surface finish 12 Ra micro inch. Item No.
Nom. Dia.
Actual Dia.
Length (mm)
Pack Qty.
Item No.
Nom. Dia.
Actual Dia.
Length (mm)
Pack Qty.
TLM-3039 TLM-3040 TLM-3041 TLM-3042 TLM-3043 TLM-3044 TLM-3045 TLM-3046 TLM-3047 TLM-3048 TLM-3049 TLM-3050 TLM-3051 TLM-3052 TLM-3053 TLM-3054 TLM-3055
12 12 12 12 12 12 16 16 16 16 16 16 20 20 20 20 20
12.00/11.99 12.00/11.99 12.00/11.99 12.00/11.99 12.00/11.99 12.00/11.99 16.00/15.99 16.00/15.99 16.00/15.99 16.00/15.99 16.00/15.99 16.00/15.99 20.00/19.99 20.00/19.99 20.00/19.99 20.00/19.99 20.00/19.99
250 500 750 1,000 1,500 2,000 250 500 750 1,000 1,500 2,000 250 500 750 1,000 1,500
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
TLM-3056 TLM-3057 TLM-3058 TLM-3059 TLM-3060 TLM-3061 TLM-3062 TLM-3063 TLM-3064 TLM-3065 TLM-3066 TLM-3067 TLM-3068 TLM-3069 TLM-3070 TLM-3071
20 25 25 25 25 25 30 30 30 30 30 40 40 40 40 40
20.00/19.99 25.00/24.99 25.00/24.99 25.00/24.99 25.00/24.99 25.00/24.99 30.00/29.99 30.00/29.99 30.00/29.99 30.00/29.99 30.00/29.99 40.00/39.99 40.00/39.99 40.00/39.99 40.00/39.99 40.00/39.99
2,000 500 750 1,000 1,500 2,000 500 750 1,000 1,500 2,000 500 750 1,000 1,500 2,000
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
848
60 CASE® LINEARRACE® SHAFTS
Thomson's 60 Case® LinearRace® shafts are precision ground to exacting standards for superior linear bearing performance and life. Case hardened to 60-65C. Stainless steel for corrosion resistance, is 440C with a hardness of 50-55C. Chrome plated steel for corrosion resistance. The ends are not plated. Roundness is 80 millionth of an inch. Surface finish 12 Ra micro inch.
Steel Item No.
Thomson
TLM-1505 TLM-1506 TLM-1507 TLM-1508 TLM-1509 TLM-1510 TLM-1511 TLM-1512 TLM-1513 TLM-1514 TLM-1515 TLM-1516 TLM-1517 TLM-1518 TLM-1519 TLM-1520 TLM-1522 TLM-1523 TLM-1524 TLM-1525 TLM-1526 TLM-1527 TLM-1528 TLM-1529 TLM-1530 TLM-1531 TLM-1532 TLM-1533 TLM-1534 TLM-1535 TLM-1536 TLM-1537 TLM-1538 TLM-1539 TLM-1540 TLM-1541 TLM-1542 TLM-1543 TLM-1544 TLM-1545
QS 1/4L X 6 QS 1/4 L X 9 QS 1/4LX12 QS 1/4LX15 QS 1/4LX18 QS 1/4LX24 QS 1/4LX30 QS 1/4LX36 QS 1/4LX42 QS 1/4LX48 QS 3/8LX6 QS 3/8LX9 QS 3/8LX12 QS 3/8LX15 QS 3/8LX18 QS 3/8LX24 QS 3/8LX36 QS 3/8LX42 QS 3/8LX48 QS 1/2LX6 QS 1/2LX9 QS 1/2LX12 QS 1/2LX15 QS 1/2LX18 QS 1/2LX24 QS 1/2LX30 QS 1/2LX36 QS 1/2LX42 QS 1/2LX48 QS 1/2LX60 QS 1/2LX72 QS 5/8LX6 QS 5/8LX9 QS 5/8LX12 QS 5/8LX15 QS 5/8LX18 QS 5/8LX24 QS 5/8LX30 QS 5/8LX36 QS 5/8LX42
Nom. Dia 1
⁄4 1 ⁄4 1 ⁄4 1 ⁄4 1 ⁄4 1 ⁄4 1 ⁄4 1 ⁄4 1 ⁄4 1 ⁄4 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8
Actual Dia.
Lgth.
Pack Qty.
Item No.
Thomson
.2495/.2490 .2495/.2490 .2495/.2490 .2495/.2490 .2495/.2490 .2495/.2490 .2495/.2490 .2495/.2490 .2495/.2490 .2495/.2490 .3745/.3740 .3745/.3740 .3745/.3740 .3745/.3740 .3745/.3740 .3745/.3740 .3745/.3740 .3745/.3740 .3745/.3740 .4995/.4990 .4995/.4990 .4995/.4990 .4995/.4990 .4995/.4990 .4995/.4990 .4995/.4990 .4995/.4990 .4995/.4990 .4995/.4990 .4995/.4990 .4995/.4990 .6245/.6240 .6245/.6240 .6245/.6240 .6245/.6240 .6245/.6240 .6245/.6240 .6245/.6240 .6245/.6240 .6245/.6240
6 9 12 15 18 24 30 36 42 48 6 9 12 15 18 24 36 42 48 6 9 12 15 18 24 30 36 42 48 60 72 6 9 12 15 18 24 30 36 42
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
TLM-1546 TLM-1547 TLM-1548 TLM-1549 TLM-1550 TLM-1551 TLM-1552 TLM-1553 TLM-1554 TLM-1555 TLM-1556 TLM-1557 TLM-1558 TLM-1559 TLM-1561 TLM-1562 TLM-1563 TLM-1564 TLM-1565 TLM-1566 TLM-1567 TLM-1568 TLM-1570 TLM-1571 TLM-1572 TLM-1573 TLM-1574 TLM-1575 TLM-1576 TLM-1577 TLM-1578 TLM-1579 TLM-1580 TLM-1581 TLM-1582 TLM-1583 TLM-1584 TLM-1585 TLM-1586 TLM-1587
QS 5/8LX48 QS 5/8LX60 QS 5/8LX72 QS 3/4LX6 QS 3/4LX9 QS 3/4LX12 QS 3/4LX15 QS 3/4LX18 QS 3/4LX24 QS 3/4LX30 QS 3/4LX36 QS 3/4LX42 QS 3/4LX48 QS 3/4LX60 QS 1LX12 QS 1LX18 QS 1LX24 QS 1LX30 QS 1LX36 QS 1LX42 QS 1LX48 QS 1LX60 QS 1-1/4LX12 QS 1-14LX18 QS 1-1/4LX24 QS 1-1/4LX30 QS 1-1/4LX36 QS 1-1/4LX42 QS 1-1/4LX48 QS 1-1/4LX60 QS 1-1/4LX72 QS 1-1/2LX12 QS 1-1/2LX18 QS 1-1/2LX24 QS 1-1/2LX30 QS 1-1/2LX36 QS 1-1/2LX42 QS 1-1/2LX48 QS 1-1/2LX60 QS 1-1/2LX72
Nom. Dia 5
⁄8 5 ⁄8 5 ⁄8 3 ⁄4 3 ⁄4 3 ⁄4 3 ⁄4 3 ⁄4 3 ⁄4 3 ⁄4 3 ⁄4 3 ⁄4 3 ⁄4 3 ⁄4 1 1 1 1 1 1 1 1 11⁄4 11⁄4 11⁄4 11⁄4 11⁄4 11⁄4 11⁄4 11⁄4 11⁄4 11⁄2 11⁄2 11⁄2 11⁄2 11⁄2 11⁄2 11⁄2 11⁄2 11⁄2
Actual Dia.
Lgth.
Pack Qty.
.6245/.6240 .6245/.6240 .6245/.6240 .7495/.7490 .7495/.7490 .7495/.7490 .7495/.7490 .7495/.7490 .7495/.7490 .7495/.7490 .7495/.7490 .7495/.7490 .7495/.7490 .7495/.7490 .9995/.9990 .9995/.9990 .9995/.9990 .9995/.9990 .9995/.9990 .9995/.9990 .9995/.9990 .9995/.9990 1.2495/1.2490 1.2495/1.2490 1.2495/1.2490 1.2495/1.2490 1.2495/1.2490 1.2495/1.2490 1.2495/1.2490 1.2495/1.2490 1.2495/1.2490 1.4994/1.4989 1.4994/1.4989 1.4994/1.4989 1.4994/1.4989 1.4994/1.4989 1.4994/1.4989 1.4994/1.4989 1.4994/1.4989 1.4994/1.4989
48 60 72 6 9 12 15 18 24 30 36 42 48 60 12 18 24 30 36 42 48 60 12 18 24 30 36 42 48 60 72 12 18 24 30 36 42 48 60 72
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Chrome Plated Steel Item No.
TLM-1701 TLM-1702 TLM-1703 TLM-1704 TLM-1705 TLM-1706
Thomson
QS 1/2LCPX6 QS 1/2LCPX12 QS 1/2LCPX18 QS 1/2LCPX24 QS 1/2LCPX36 QS 3/4LCPX6
Nom. Dia. 1
Actual Dia
Lgth.
Pack Qty.
Item No.
Thomson
TLM-1707 QS 3/4LCPX12 TLM-1708 QS 3/4LCPX18 TLM-1709 QS 3/4LCPX24 TLM-1712 QS 1LCPX12 TLM-1713 QS 1LCPX18 TLM-1714 QS 1LCPX24
⁄2 ⁄2 ⁄2 1 ⁄2 1 ⁄2 3 ⁄4
.4995/.4990 .4995/.4990 .4995/.4990 .4995/.4990 .4995/.4990 .7495/.7490
6 12 18 24 36 6
1 1 1 1 1 1
Nom. Dia.
Actual Dia.
Lgth.
Pack Qty.
Item No.
Thomson
.2495/.2490 .2495/.2490 .2495/.2490 .2495/.2490 .2495/.2490 .2495/.2490 .3745/.3740 .3745/.3740 .3745/.3740 .3745/.3740 .4995/.4990 .4995/.4990 .4995/.4990 .4995/.4990 .4995/.4990 .4995/.4990 .6245/.6240
6 12 18 24 36 48 6 12 18 36 6 12 18 24 36 48 6
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
TLM-1620 TLM-1621 TLM-1622 TLM-1623 TLM-1624 TLM-1625 TLM-1626 TLM-1627 TLM-1628 TLM-1629 TLM-1630 TLM-1631 TLM-1632 TLM-1633 TLM-1634 TLM-1635
QS 5/8LSSX12 QS 5/8LSSX18 QS 5/8LSSX24 QS 5/8LSSX36 QS 5/8LSSX48 QS 3/4LSSX6 QS 3/4LSSX12 QS 3/4LSSX18 QS 3/4LSSX24 QS 3/4LSSX36 QS 3/4LSSX48 QS 1LSSX12 QS 1LSSX18 QS 1LSSX24 QS 1LSSX36 QS 1LSSX48
1 1
Nom. Dia.
Actual Dia
Lgth.
Pack Qty.
⁄4 ⁄4 ⁄4 1 1 1
.7495/.7490 .7495/.7490 .7495/.7490 .9995/.9990 .9995/.9990 .9995/.9990
12 18 24 12 18 24
1 1 1 1 1 1
Nom. Dia.
Actual Dia.
Lgth.
Pack Qty.
.6245/.6240 .6245/.6240 .6245/.6240 .6245/.6240 .6245/.6240 .7495/.7490 .7495/.7490 .7495/.7490 .7495/.7490 .7495/.7490 .7495/.7490 .9995/.9990 .9995/.9990 .9995/.9990 .9995/.9990 .9995/.9990
12 18 24 36 48 6 12 18 24 36 48 12 18 24 36 48
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
3 3 3
Stainless Steel Item No.
Thomson
TLM-1601 TLM-1602 TLM-1603 TLM-1604 TLM-1605 TLM-1606 TLM-1607 TLM-1608 TLM-1609 TLM-1611 TLM-1613 TLM-1614 TLM-1615 TLM-1616 TLM-1617 TLM-1618 TLM-1619
QS 1/4LSSX6 QS 1/4LSSX12 QS 1/4LSSX18 QS 1/4LSSX24 QS 1/4LSSX36 QS 1/4LSSX48 QS 3/8LSSX6 QS 3/8LSSX12 QS 3/8LSS18 QS 3/8LSSX36 QS 1/2LSSX6 QS 1/2LSSX12 QS 1/2LSSX18 QS 1/2LSSX24 QS 1/2LSSX36 QS 1/2LSSX48 QS 5/8LSSX6
1
⁄4 ⁄4 ⁄4 1 ⁄4 1 ⁄4 1 ⁄4 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 5 ⁄8 1 1
5
⁄8 ⁄8 ⁄8 5 ⁄8 5 ⁄8 3 ⁄4 3 ⁄4 3 ⁄4 3 ⁄4 3 ⁄4 3 ⁄4 1 1 1 1 1 5 5
849
SUPER BALL BUSHING® BEARINGS Pillow Blocks Open Type For Continuously Supported Applications Single and Twin
C L
A J D B G E
s s s s s
M
K
Adjusting Screw
F
Double acting seals retain lubrication and keep contamination out Easily mounted with four mounting bolts Built-in lubrication wick for continuous lubrication Travel speeds up to 10 ft/s 1 ⁄2 has lubrication fitting, larger sizes have 1⁄4-28 access for lubrication M Item No.
Single TLM-750 TLM-755 TLM-760 TLM-765 TLM-775 Twin TLM-905 TLM-910 TLM-915 TLM-920 TLM-930
Thomson
Dia.
A
B
C
+/-.003 D
E
F
Min. G
+/-.010 J
K
+/-.010 L
Hole
Bolt
Dynamic Load (Lbs.)
Pack Qty.
SPB-8-OPN SPB-10-OPN SPB-12-OPN SPB-16-OPN SPB-24-OPN
.500 .625 .750 1.000 1.500
2.00 2.50 2.75 3.25 4.75
1.13 1.44 1.56 2.00 2.500
1.50 1.75 1.88 2.63 3.75
.687 .875 .937 1.187 1.750
.69 .88 .94 1.19 1.75
.75 .94 1.00 1.25 1.88
.31 .37 .43 .56 .75
1.688 2.125 2.375 2.875 4.125
.25 .28 .31 .38 .50
1.000 1.125 1.250 1.750 2.94
.16 .19 .19 .22 .28
#6 #8 #8 #10 1 ⁄4
180 320 470 780 1,560
1 1 1 1 1
TWN-8-OPN TWN-10-OPN TWN-12-OPN TWN-16-OPN TWN-24-OPN
.500 .625 .750 1.000 1.500
2.00 2.50 2.75 3.25 4.75
1.13 1.44 1.56 2.00 2.94
3.50 4.00 4.50 6.00 9.00
.687 .875 .937 1.187 1.750
.69 .88 .94 1.19 1.75
.75 .94 1.00 1.25 1.88
.31 .37 .43 .56 .75
1.688 2.125 2.375 2.875 4.125
.25 .28 .31 .38 .50
2.500 3.000 3.500 4.500 6.500
.16 .19 .19 .22 .28
#6 #8 #8 #10 1 ⁄4
360 640 940 1,560 3,120
1 1 1 1 1
Pillow Blocks Closed Type For End Supported Applications Single and Twin
B L
F
K
J E A
D C
G
s Double acting seal retain lubrication and keep contamination out s Easily mounted with four mounting bolts s Travel speed up to 10 ft/s Item No.
Single TLM-705 TLM-710 TLM-715 TLM-720 TLM-725 TLM-730 TLM-735 TLM-740 Twin TLM-850 TLM-855 TLM-860 TLM-865 TLM-870 TLM-875 TLM-880 TLM-885
850
J
Thomson
Dia.
A
B
C
+/-.010 D
+/-.010 E
F
G
Hole
Bolt
+/-.003 K
L
Dynamic Load (Lbs.)
Pack Qty.
SPB-4 SPB-6 SPB-8 SPB-10 SPB-12 SPB-16 SPB-20 SPB-24
.250 .375 .500 .625 .750 1.000 1.250 1.500
1.63 1.75 2.00 2.50 2.75 3.25 4.00 4.75
1.00 1.13 1.38 1.75 1.88 2.38 3.00 3.50
1.19 1.31 1.69 1.94 2.06 2.81 3.63 4.00
.750 .875 1.000 1.125 1.250 1.750 2.000 2.500
1.313 1.438 1.688 2.125 2.375 2.875 3.500 4.125
.75 .88 1.13 1.44 1.56 1.94 2.50 2.88
.19 .19 .25 .28 .31 .38 .44 .50
.16 .16 .16 .19 .19 .22 .22 .28
#6 #6 #6 #8 #8 #10 #10 1 ⁄4
.437 .500 .687 .875 .937 1.187 1.500 1.750
.81 .94 1.25 1.63 1.75 2.19 2.81 3.25
60 100 255 450 600 1,050 1,500 2,000
1 1 1 1 1 1 1 1
TWN-4 TWN-6 TWN-8 TWN-10 TWN-12 TWN-16 TWN-20 TWN-24
.250 .375 .500 .625 .750 1.000 1.250 1.500
1.63 1.75 2.00 2.50 2.75 3.25 4.00 4.75
1.00 1.13 1.38 1.75 1.88 2.38 3.00 3.50
2.50 2.75 3.50 4.00 4.50 6.00 7.50 9.00
2.000 2.250 2.500 3.000 3.500 4.500 5.500 6.500
1.313 1.438 1.688 2.125 2.375 2.875 3.500 4.125
.75 .88 1.13 1.44 1.56 1.94 2.50 2.88
.19 .19 .25 .28 .31 .38 .44 .50
.16 .16 .16 .19 .19 .22 .22 .28
#6 #6 #6 #8 #8 #10 #10 1 ⁄4
.437 .500 .687 .875 .937 1.187 1.500 1.750
.81 .94 1.25 1.63 1.75 2.19 2.81 3.25
120 200 510 900 1,200 2,100 3,000 4,000
1 1 1 1 1 1 1 1
SUPER SMART BALL BUSHING® BEARINGS Pillow Blocks Open Type For Continuously Supported Applications Single and Twin
C L
A J B
K
D G E
s s s s s
M
Adjusting Screw
F
Increased travel life over conventional bearings Allows for heavier loads in less space than other bushings Interchangeable with Super Ball Bushing pillow blocks Travel speeds up to 10 ft/s Easily mounted with four mounting bolts M Item No.
Single TLM-1105 TLM-1110 TLM-1115 TLM-1120 TLM-1130 Twin TLM-1140 TLM-1145 TLM-1150 TLM-1155 TLM-1165
Thomson
Dia.
A
B
C
+/-.003 D
E
F
Min. G
+/-.010 J
K
+/-.010 L
Hole
Bolt
Dynamic Load (Lbs.)
Pack Qty.
SSUPBO-8 SSUPBO-10 SSUPBO-12 SSUPBO-16 SSUPBO-24
.500 .625 .750 1.000 1.500
2.00 2.50 2.75 3.25 4.75
1.13 1.44 1.56 2.00 2.94
1.50 1.75 1.88 2.63 3.75
.687 .875 .937 1.187 1.750
.69 .88 .94 1.19 1.75
.75 .94 1.00 1.25 1.88
.31 .34 .41 .53 .74
1.688 2.125 2.375 2.875 4.125
.25 .28 .31 .38 .50
1.000 1.125 1.250 1.750 2.500
.16 .19 .19 .22 .28
#6 #8 #8 #10 1 ⁄4
360 620 1,130 1,900 3,880
1 1 1 1 1
SSUTWNO-8 SSUTWNO-10 SSUTWNO-12 SSUTWNO-16 SSUTWNO-24
.500 .625 .750 1.000 1.500
2.00 2.50 2.75 3.25 4.75
1.13 1.44 1.56 2.00 2.94
3.50 4.00 4.50 6.00 9.00
.687 .875 .937 1.187 1.750
.69 .88 .94 1.19 1.75
.75 .94 1.00 1.25 1.88
.31 .34 .41 .53 .74
1.688 2.125 2.375 2.875 4.125
.25 .28 .31 .38 .50
2.500 3.000 3.500 4.500 6.500
.16 .19 .19 .22 .28
#6 #8 #8 #10 1 ⁄4
720 1,240 2,260 3,800 7,760
1 1 1 1 1
Pillow Blocks Closed Type For End Supported Applications Single and Twin
B L
F
K
s s s s s
Increased travel life over conventional bearings Allows for heavier loads in less space than other bushings Interchangeable with Super Ball Bushing pillow blocks Travel speeds up to 10 ft/s Easily mounted with four mounting bolts Item No.
Thomson
Single TLM-950 SS6UPB-8 TLM-955 SSUPB-10 TLM-960 SSUPB-12 TLM-965 SSUPB-16 TLM-970 SSUPB-20 TLM-975 SSUPB-24 Twin TLM-1010 SSUTWN-10 TLM-1015 SSUTWN-12 TLM-1020 SSUTWN-16
J E A
D C
G
J
Dia.
A
B
C
+/-.010 D
+/-.010 E
F
G
Hole
Bolt
+/-.003 K
L
Dynamic Load (Lbs.)
Pack Qty.
.500 .625 .750 1.000 1.250 1.500
2.00 2.50 2.75 3.25 4.00 4.75
1.38 1.75 1.88 2.38 3.00 3.50
1.69 1.94 2.06 2.81 3.63 4.00
1.000 1.125 1.250 1.750 2.000 2.500
1.688 2.125 2.375 2.875 3.500 4.125
1.13 1.44 1.56 1.94 2.50 2.88
.25 .28 .31 .38 .44 .50
.16 .19 .19 .22 .22 .28
#6 #8 #8 #10 #10 .25
.687 .875 .937 1.187 1.500 1.750
1.25 1.63 1.75 2.19 2.81 3.25
265 620 1,130 1,900 2,350 3,880
1 1 1 1 1 1
.625 .750 1.000
2.50 2.75 3.25
1.75 1.88 2.38
4.00 4.50 6.00
3.000 3.500 4.500
2.125 2.375 2.875
1.44 1.56 1.94
.28 .31 .38
.19 .19 .22
#8 #8 #10
.875 .937 1.187
1.63 1.75 2.19
1,240 2,260 3,800
1 1 1
851
BEARINGS Super Ball Bushing® Flanged Pillow Blocks For End Supported Applications Single and Twin
A B
s Easily mounted and secured with four mounting bolts s Can be mounted perpendicular to table surface s These pillow blocks are interchangeable with the Super Smart Ball Bushing flanged pillow blocks s Allows for travel speeds up to 10 ft/s Item No.
Single TLM-805 TLM-810 TLM-815 Twin TLM-820 TLM-825 TLM-830
D
F
E
C
AB
Access for Lubrication
Thomson
Dia.
A
+/-.010 B
C
D
E
F
Dynamic Load (Lbs.)
Pack Qty.
SFB8 SFB12 SFB-16
.500 .750 1.000
1.63 2.38 2.75
1.250 1.750 2.125
1.25 1.75 2.25
1.69 2.06 2.81
.25 .38 .50
.19 .21 .28
255 600 1,050
1 1 1
TSFB-8 TSFB12 TSFB16
.500 .750 1.000
1.63 2.38 2.75
1.250 1.750 2.125
1.25 1.75 2.25
3.20 3.95 5.33
.90 .90 .90
⁄4-20 ⁄4-20 ⁄16-18
510 1,200 2,100
1 1 1
1 1 5
Bearings Open Type For Continuously Supported Applications
B
N OP
THO
C N SUPER SO M
F
D F
s Can be mounted in a customized open style pillow block s Travel speeds up to 10 ft/s s Self-aligning in all directions
A
E
Item No.
Thomson
Dia.
A
B
C
D
E
Ang. Deg. F
No. of Ball Circuits
Dynamic Load (Lbs.)
Pack Qty.
TLM-450 TLM-455 TLM-460 TLM-465 TLM-470 TLM-475
SUPER 8-OPN SUPER 10-OPN SUPER 12-OPN SUPER 16-OPN SUPER 20-OPN SUPER 24-OPN
.500 .625 .750 1.000 1.250 1.500
1.250/1.230 1.500/1.480 1.625/1.605 2.250/2.230 2.625/2.600 3.000/2.970
1.032/1.012 1.105/1.095 1.270/1.250 1.884/1.864 2.004/1.984 2.410/2.390
.050 .056 .056 .070 .068 .086
.8755/.8750 1.1255/1.1250 1.2505/1.2500 1.5630/1.5625 2.0008/2.0000 2.3760/2.3750
.31 .37 .43 .56 .62 .75
15 15 15 15 15 15
3 4 5 5 5 5
180 320 470 780 1,170 1,560
1 1 1 1 1 1
Bearings Closed Type For End Supported Applications
D
C
s Can be mounted in a customized housing s Travel speeds up to 10 ft/s s Self-aligning in all directions
B
A
Item No.
Thomson
Dia.
A
B
C
D
No. of Ball Circuits
Dynamic Load (Lbs.)
Pack Qty.
TLM-405 TLM-410 TLM-415 TLM-420 TLM-425 TLM-430 TLM-435 TLM-440 TLM-445
SUPER 3 SUPER 4 SUPER 6 SUPER 8 SUPER 10 SUPER 12 SUPER 16 SUPER 20 SUPER 24
.188 .250 .375 .500 .625 .750 1.000 1.250 1.500
.562/.547 .750/.735 .875/.860 1.250/1.230 1.500/1.480 1.625/1.605 2.250/2.230 2.625/2.600 3.000/2.970
— .511/.501 .699/.689 1.032/1.012 1.105/1.095 1.270/1.250 1.884/1.864 2.004/1.984 2.410/2.390
— .039 .039 .050 .056 .056 .070 .068 .086
.3755/.3750 .5005/.5000 .6255/.6250 .8755/.8750 1.1255/1.1250 1.2505/1.2500 1.5630/1.5625 2.0008/2.0000 2.3760/2.3750
4 4 4 4 5 6 6 6 6
35 60 100 255 450 600 1,050 1,500 2,000
1 1 1 1 1 1 1 1 1
852
BEARINGS Super Smart Ball Bushing® Flanged Pillow Blocks For End Supported Applications Single and Twin
A B
s Easily mounted and secured with four mounting bolts s Can be mounted perpendicular to table surface s These pillow blocks are interchangeable with the Super Ball Bushing flanged pillow blocks s Allows for travel speeds up to 10 ft/s Item No.
Single TLM-1210 TLM-1215 TLM-1220 TLM-1225 Twin TLM-1235 TLM-1240 TLM-1245 TLM-1250
F
D
E
C
AB
Access for Lubrication
Thomson
Dia.
A
+/-.010 B
C
D
E
F
Dynamic Load (Lbs.)
Pack Qty.
SSUFB-12 SSUFB-16 SSUFB-20 SSUFB-24
.750 1.000 1.250 1.500
2.38 2.75 3.50 4.00
1.750 2.125 2.750 3.125
1.75 2.25 3.00 3.62
2.06 2.81 3.63 4.00
.38 .50 .63 .75
.22 .28 .35 .41
1,130 1,900 2,350 3,880
1 1 1 1
SS6UTFB-8 SSUTFB-12 SSUTFB-16 SSUTFB-20
.500 .750 1.000 1.250
1.63 2.38 2.75 3.50
1.250 1.750 2.125 2.750
1.25 1.75 2.25 3.00
3.20 3.95 5.33 6.70
.90 .90 .90 .90
⁄4-20 ⁄4-20 ⁄16-18 5 ⁄16-18
530 2,260 3,800 4,700
1 1 1 1
1 1
5
Bearings Open Type For Continuously Supported Applications With Wipers
B C D
s s s s
E F
Increased travel life over conventional bearings Allows for heavier loads in less space than other bushings Interchangeable with Super Ball Bushing bearings Travel speeds up to 10 ft/s
Roll Pin
A
Item No.
Thomson
Dia.
A
B
C
D
E
Ang. Deg. F
No. of Ball Circuits
Dynamic Load (Lbs.)
Pack Qty.
TLM-640 TLM-645 TLM-650 TLM-655
SSU8-OPNWW SSU10-OPNWW SSU12-OPNWW SSU16-OPNWW
.500 .625 .750 1.000
1.250/1.230 1.500/1.480 1.625/1.605 2.250/2.230
1.032/1.012 1.125/1.095 1.285/1.255 1.901/1.871
.050 .055 .055 .068
.8755/.8750 1.2550/1.1250 1.2505/1.2500 1.5603/1.5625
.31 .34 .41 .53
40 30 30 30
6 8 8 8
360 620 1,130 1,190
1 1 1 1
Bearings Closed Type For End Supported Applications With or Without Wipers
B D
s s s s s
C
Increased travel life over conventional bearings Allows for heavier loads in less space than other bushings Interchangeable with Super Ball Bushing bearings Travel speeds up to 10 ft/s Can be mounted in a customized housing w/ No Wipers Item No.
Thomson
A
w/ Two Wipers Item No.
Thomson
TLM-505 SS6U-8 TLM-535 SS6U-8WW — TLM-540 SSU-10WW — TLM-515 SSU-12 TLM-545 SSU-12WW TLM-520 SSU-16 TLM-550 SSU-16WW — TLM-555 SSU-20WW — — TLM-560 SSU-24WW —
Dia.
A
B
C
D
No. of Ball Circuits
Dynamic Load (Lbs.)
Pack Qty.
.500 .625 .750 1.000 1.250 1.500
1.250/1.230 1.500/1.480 1.625/1.605 2.250/2.230 2.625/2.600 3.000/2.970
1.032/1.012 1.125/1.095 1.285/1.255 1.901/1.871 2.031/1.991 2.442/2.402
.050 .055 .055 .068 .068 .086
.8755/.8750 1.1255/1.1250 1.2505/1.2500 1.5630/1.5625 2.0008/2.0000 2.3760/2.3750
6 10 10 10 10 10
265 620 1,130 1,900 2,350 3,880
1 1 1 1 1 1
853
60 CASE® LINEARRACE® SHAFTS Steel Shaft Rail Assemblies
Pre-drilled shafting mounts easily to pre-drilled support rails. For use with open style bearings and pillow blocks. All holes are drilled and tapped to the center of the shaft. Rails provide support over the entire length of the shaft. All supporting rails are made from aluminum alloy. 24 inch lengths. The assemblies include the shaft already mounted on the rail for easy installation. Item No.
Shaft Dia.
24" Lgth. TLM-1950 TLM-1951 TLM-1952 TLM-1953 48" Lgth. TLM-1956 TLM-1957 TLM-1958 TLM-1959
Pack Qty.
1
⁄2 ⁄8 ⁄4 1
1 1 1 1
1
1 1 1 1
5 3
⁄2 ⁄8 ⁄4 1
5 3
Pre-Drilled Shaft Support Rails
A G H
20° B C
K
F D
J
Pre-drilled shafting mounts easily to pre-drilled support rails. For use with open style bearings and pillow blocks. All holes are drilled and tapped to the center of the shaft. Rails provide support over the entire length of the shaft. All supporting rails are made from aluminum alloy. The assemblies include the shaft already mounted on the rail for easy installation. Item No.
TLM-1901 TLM-1902 TLM-1903 TLM-1904 TLM-1905 TLM-1906
A 1
⁄2 ⁄8 ⁄4 1 11⁄4 11⁄2 5 3
H
+/-.002 B
C
D
F
G
Hole
Bolt
Length
Linear Race Mounting Bolt
J
K
Pack Qty.
1.125 1.125 1.500 1.750 2.125 2.500
.19 .25 .25 .25 .31 .38
1.50 1.63 1.75 2.13 2.50 3.00
1.00 1.13 1.25 1.50 1.88 2.25
.25 .31 .38 .50 .56 .69
.17 .19 .22 .28 .34 .34
#6 #8 #10 1 ⁄4 5 ⁄16 5 ⁄16
24 24 24 24 24 24
6-32 x .88 8-32 x .88 10-32 x 1.25 1 ⁄4-20 x 1.50 5 ⁄16-18 x 1.75 3 ⁄8-16 x 2.00
4 4 6 6 6 8
2 2 3 3 3 4
1 1 1 1 1 1
Pre-Drilled 60 Case® LinearRace® Shafting Steel and Stainless Steel
C
D ±1/32 A
B
Pre-drilled shafting for support rails. For use with open style bearings and pillow blocks. All holes are drilled and tapped to the center of the shaft. Made of either steel or stainless steel. Steel
Stainless
Item No.
Item No.
TLM-1801 TLM-1802 TLM-1803 TLM-1804 TLM-1805 TLM-1806 TLM-1807 TLM-1808 TLM-1809 TLM-1810 TLM-1811 TLM-1812 TLM-1814 TLM-1816 TLM-1817
854
TLM-1831 — — TLM-1834 — TLM-1836 TLM-1837 TLM-1838 TLM-1839 TLM-1840 TLM-1841 TLM-1842 — — —
A 1
⁄2 ⁄2 ⁄2 5 ⁄8 5 ⁄8 5 ⁄8 3 ⁄4 3 ⁄4 3 ⁄4 1 1 1 11⁄4 11⁄2 11⁄2 1 1
B
C
D
Thread
Pack Qty.
24 48 72 24 48 72 24 48 72 24 48 72 72 48 72
4 4 4 4 4 4 6 6 6 6 6 6 6 8 8
2 2 2 2 2 2 3 3 3 3 3 3 3 4 4
6-32 6-32 6-32 8-32 8-32 8-32 10-32 10-32 10-32 1 ⁄4-20 1 ⁄4-20 1 ⁄4-20 5 ⁄16-18 3 ⁄8-16 3 ⁄8-16
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
SHAFT SUPPORTS & BEARINGS Flanged Support Blocks
Shaft Support Blocks
F
C
B
G
D B A
E
H
A C
D
E
G
AC
J
F B
For end supported applications. Easily secured with two mounting bolts. Made from malleable iron alloy with corrosion resistant coating. Block can be reamed to accommodate larger shafts. Item No.
Thomson Dia.
TLM-2003 TLM-2004 TLM-2005 TLM-2006 TLM-2007 TLM-2008
1
SB 8 SB 10 SB 12 SB16 SB 20 SB 24
⁄2 ⁄8 ⁄4 1 11⁄4 11⁄2 5 3
G
A
+/-.010 B
C
+/-.002 D
E
F
Hole
Bolt
H
Pack Qty.
2 21⁄2 23⁄4 31⁄4 4 43⁄4
1.500 1.875 2.000 2.500 3.000 3.500
1.63 1.75 2.13 2.56 3.00 3.50
1.000 1.000 1.250 1.500 1.750 2.000
.63 .69 .75 1.00 1.13 1.25
.75 .88 1.00 1.38 1.75 2.00
.19 .22 .22 .28 .34 .34
#8 #10 #10 .25 .31 .31
.25 .31 .31 .38 .44 .50
1 1 1 1 1 1
Flanged mounting surface for easy assembly. Secured with four mounting bolts. Made of high strength aluminum alloy. Block can be reamed to accommodate larger shafts. Item No.
Thomson
TLM-2020 FSB 8 TLM-2021 FSB 12 TLM-2022 FSB 16 TLM-2023 FSB 20
1
⁄2 ⁄4 1 11⁄4 3
G
A
B
+/-.010 C
D
E
F
Hole
Bolt
J
Pack Qty.
1.63 2.38 2.75 3.13
.81 1.19 1.38 1.56
1.250 1.750 2.125 2.375
.88 1.00 1.25 1.38
.50 .63 .63 .75
1.00 1.25 1.50 1.75
.18 .21 .27 .27
#8 #10 1 ⁄4 1 ⁄4
.25 .31 .31 .38
1 1 1 1
Dia.
Open Type for Continuously Supported Applications Steel Balls
C
B
D E F
s s s s s
A
Coefficient of friction as low as 0.001 All steel construction for maximum rigidity Travel speeds up to 10 ft/s High temperature capability Can be mounted in a customized open style pillow block
Item No.
Thomson
Dia.
A
B
C
D
E
Angle Degree F
No. of Ball Circuits
Dynamic Load (Lbs.)
Pack Qty.
TLM-105 TLM-110 TLM-115 TLM-120
OPN81420 OPN101824 OPN122026 OPN162536
.500 .625 .750 1.000
1.250/1.235 1.500/1.485 1.625/1.610 2.250/2.235
.987/.951 1.108/1.092 1.170/1.154 1.759/1.741
.046 .056 .056 .068
.8760/.8740 1.2600/1.1240 1.2510/1.2490 1.5635/1.5615
.31 .38 .44 .56
50 60 60 60
3 3 4 4
60 105 140 240
1 1 1 1
Closed Type for End Supported Applications Steel and Stainless Steel Balls
D
B
C
s s s s s
A
Steel Item No.
Thomson
TLM-10 TLM-15 TLM-20 TLM-25 TLM-30 TLM-35 TLM-40 TLM-45
A-4812 A-61014 A-81420 A-101824 A-122026 A-162536 A-203242 A-243848
Coefficient of friction as low as 0.001 All steel construction for maximum rigidity Travel speeds up to 10 ft/s High temperature capability Can be mounted in customized housing
Stainless Item No.
Thomson
TLM-50 A-4812SS TLM-55 A-61014SS TLM-60 A-81420SS — — TLM-65 A-122026SS — — — — — —
Dia.
A
B
C
D
No. of Ball Circuits
Dynamic Load (Lbs.)
Pack Qty.
.250 .375 .500 .625 .750 1.000 1.250 1.500
.750/.735 .875/.860 1.250/1.235 1.500/1.485 1.625/1.610 2.250/2.235 2.625/2.605 3.000/2.980
.515/.499 .640/.624 .967/.951 1.108/1.092 1.170/1.154 1.759/1.741 2.009/1.991 2.415/2.397
.039 .039 .046 .056 .056 .068 .068 .086
.5000/.4996 .6250/.6246 .8750/.8746 1.1250/1.1246 1.2500/1.2496 1.5625/1.5621 2.0000/1.9995 2.3750/2.3745
3 4 4 4 5 5 6 6
19 37 85 150 200 350 520 770
1 1 1 1 1 1 1 1
Note: 60 Case® LinearRace® shafts are not recommended for these bearings. S style shafting is recommended.
855
LINEAR BEARINGS Smooth Plane Bearings Inch & Metric Pacific Bearing's plane bearing technology offers many design advantages over roller ball bearings. Some of these advantages include: s s s s s s s
Self-lubricating which requires no external lubricant Embeddability of hard particulate eliminates galling and shaft damage Dampens vibration for quiet and smooth operation - no metal to metal contact High load capacity allows for more compact design Shock loads are absorbed without damage to components Maintenance free with a reliable, predictable life that will not catastrophically fail High temperature range (-400 to +500 degrees Fahrenheit and chemically inert
The plane bearing liner is made of FrelonGOLD®, a compound PTFE. The interaction of the FrelonGOLD® material and the shafting creates a natural, microscopic transfer process of the FrelonGOLD to the running surfaces. The valleys in the surface finish are filled in with FrelonGOLD® during the initial break-in period. This creates the self-lubricating condition. A minimum of initial lubrication is recommended to aid in cleaning the shaft for a proper transfer process. Chrome plated shafting is not recommended. The compensated styles below, offer additional running clearance. The bearing shell is 6061-T6 aluminum with anodized finish. E
Closed Style - Inch
B
A D C
Closed Style Item No.
Pacific
Nominal Dia.
Precision Style 3 PBC-05 FL03 ⁄16 1 PBC-06 FL04 ⁄4 3 PBC-07 FL06 ⁄8 1 PBC-08 FL08 ⁄2 5 PBC-09 FL10 ⁄8 3 PBC-10 FL12 ⁄4 PBC-11 FL16 1 PBC-12 FL20 11⁄4 PBC-13 FL24 11⁄2 PBC-14 FL32 2 Compensated Style 3 PBC-25 FLC03 ⁄16 1 PBC-26 FLC04 ⁄4 3 PBC-27 FLC06 ⁄8 1 PBC-28 FLC08 ⁄2 5 PBC-29 FLC10 ⁄8 3 PBC-30 FLC12 ⁄4 PBC-31 FLC16 1 PBC-32 FLC20 11⁄4 PBC-33 FLC24 11⁄2
Effective Surface Max. Static Area (Sq. In.) Load (Lbs.)
A
B
C
D
E
.1880/.1890 .2500/.2510 .3750/.3760 .5000/.5010 .6250/.6260 .7500/.7510 1.0000/1.0010 1.2500/1.2510 1.500/1.5012 2.000/2.0014
.3740/.3750 .4990/.5000 .6240/.6250 .8740/.8750 1.1240/1.1250 1.2490/1.2500 1.5613/1.5625 1.9988/2.0000 2.3738/2.3750 2.9986/3.0000
.547/.562 .735/.750 .860/.875 1.235/1.250 1.485/1.500 1.610/1.625 2.235/2.250 2.605/2.625 2.980/3.000 3.980/4.000
.375 .437 .562 .875 1.000 1.062 1.625 1.875 2.250 3.000
.030 .041 .041 .048 .058 .058 .070 .070 .089 .105
.110 .200 .340 .650 .980 1.270 2.350 3.430 4.700 8.350
.1890/.1900 .2520/.2530 .3770/.3780 .5020/.5030 .6270/.6280 .7530/.7540 1.0030/1.0040 1.2540/1.2550 1.5040/1.5052
.3740/.3750 .4990/.5000 .6240/.6250 .8740/.8750 1.1240/1.1250 1.2490/1.2500 1.5613/1.5625 1.9988/2.0000 2.3738/2.3750
.547/.562 .735/.750 .860/.875 1.235/1.250 1.485/1.500 1.610/1.625 2.235/2.250 2.605/2.625 2.980/3.000
.375 .437 .562 .875 1.000 1.062 1.625 1.875 2.250
.030 .041 .041 .048 .058 .058 .070 .070 .089
.110 .200 .340 .650 .980 1.270 2.350 3.430 4.700
Max. Speed Ft./Min. Dry
Lubricated
Pack Qty.
110 300 510 975 1,470 1,905 3,525 5,145 7,050 12525
140 140 140 140 140 140 140 140 140 140
400 400 400 400 400 400 400 400 400 400
1 1 1 1 1 1 1 1 1 1
110 300 510 975 1,470 1,905 3,525 5,145 7,050
140 140 140 140 140 140 140 140 140
400 400 400 400 400 400 400 400 400
1 1 1 1 1 1 1 1 1
E
Open Style - Inch B F
A D C
G
Open Style Item No.
Pacific
Nominal Dia.
Precision Style PBC-40 FLN08 PBC-41 FLN10 PBC-42 FLN12 PBC-43 FLN16 PBC-44 FLN20 Compensated Style PBC-50 FLCN08 PBC-52 FLCN12 PBC-53 FLCN16 PBC-54 FLCN20 PBC-55 FLCN24
1
⁄2 ⁄8 ⁄4 1 11⁄4 5 3
1
⁄2 ⁄4 1 11⁄4 11⁄2 3
Effective Surface Max. Static Area (Sq. In.) Load (Lbs.)
A
B
C
D
E
F
G (degrees)
Retaining Hole Dia.
.5000/.5010 .6250/.6260 .7500/.7510 1.0000/1.0010 1.2500/1.2510
.8740/.8750 1.1240/1.1250 1.2490/1.2500 1.5613/1.5625 1.9988/2.0000
1.235/1.250 1.485/1.500 1.610/1.625 2.235/2.250 2.605/2.625
.875 1.000 1.062 1.625 1.875
.048 .058 .058 .070 .070
.313 .375 .438 .563 .625
60 60 60 60 60
.136 .136 .136 .136 .201
.650 .980 1.270 2.350 3.430
.5020/.5030 .7530/.7540 1.0030/1.0040 1.2540/1.2550 1.5040/1.5052
.8740/.8750 1.2490/1.2500 1.5613/1.5625 1.9988/2.0000 2.3738/2.3750
1.235/1.250 1.610/1.625 2.235/2.250 2.605/2.625 2.980/3.000
.875 1.062 1.625 1.875 2.250
.048 .058 .070 .070 .089
.313 .438 .563 .625 .750
60 60 60 60 60
.136 .136 .136 .201 .201
.650 1.270 2.350 3.430 4.700
Max. Speed Ft./Min. Dry
Lubricated
Pack Qty.
975 1,470 1,905 3,525 5,145
140 140 140 140 140
400 400 400 400 400
1 1 1 1 1
975 1,905 3,525 5,145 7,050
140 140 140 140 140
400 400 400 400 400
1 1 1 1 1
E
Closed Style - Metric B
A
Similar to the linear bearings shown above except in standard European metric. Dimensions are in millimeters.
D C
Max. Speed Ft./Min.
Item No.
Pacific
Nominal Dia.
A
B
C
D
E
Effective Surface Area (Sq. cm.)
Max. Static Load (kg)
Dry
Lubricated
Pack Qty.
Precision PBC-907 PBC-908 PBC-909 PBC-910 PBC-911
Style FM10 FM12 FM16 FM20 FM25
10 12 16 20 25
10.013/10.035 12.016/12.043 16.016/16.043 20.020/20.053 25.020/25.053
18.974/19.000 21.979/22.000 25.979/26.000 31.975/32.000 39.975/40.000
28.746/29.000 31.746/32.000 35.746/36.000 44.746/45.000 57.746/58.000
19.4 20.0 22.0 28.0 40.0
1.32 1.32 1.32 1.32 1.32
2.9 3.8 5.8 9.0 14.5
305 403 605 945 1,523
42.6 42.6 42.6 42.6 42.6
122 122 122 122 122
1 1 1 1 1
856
LINEAR SHAFTS Economical weight saving alternative to traditional steel shafting. Made from 6061-T6 aluminum with a ceramic-coated finish that has a Rockwell hardness of 70C. Surface is non-magnetic and vibration resistant. Weld splatter, paints and contaminants will not stick. Shafting is designed to be used with the Simplicity FrelonGOLD® lined linear bearings. Note: Do not use with ball bearings. Pre-drilled and tapped shafting is interchangeable with standard pre-drilled shafting. Ends of shafting are not coated.
Solid, Pre-drilled, and Tapped Shafts
Solid Solid
See facing page for Simplicity FrelonGold® lined linear bearings. Item No.
PBC-1030 PBC-1031 PBC-1032 PBC-1033 PBC-1034 PBC-1035 PBC-1036 PBC-1037 PBC-1038 PBC-1039 PBC-1040 PBC-1041 PBC-1042 PBC-1043 PBC-1044 PBC-1045 PBC-1046 PBC-1047 PBC-1048 PBC-1049 PBC-1050 PBC-1051 PBC-1052 PBC-1053 PBC-1054 PBC-1055 PBC-1056 PBC-1057 PBC-1058 PBC-1059
Nominal OD 3
⁄16 ⁄16 ⁄16 3 ⁄16 3 ⁄16 3 ⁄16 1 ⁄4 1 ⁄4 1 ⁄4 1 ⁄4 1 ⁄4 1 ⁄4 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 3 3
Lgth.
Dia. Tolerance
Weight Per Inch
Pack Qty.
Item No.
6 9 12 15 18 24 6 9 12 15 18 24 6 9 12 15 18 24 6 9 12 15 18 24 6 9 12 15 18 24
.1863/.1871 .1863/.1871 .1863/.1871 .1863/.1871 .1863/.1871 .1863/.1871 .2488/.2496 .2488/.2496 .2488/.2496 .2488/.2496 .2488/.2496 .2488/.2496 .3738/.3746 .3738/.3746 .3738/.3746 .3738/.3746 .3738/.3746 .3738/.3746 .4988/.4996 .4988/.4996 .4988/.4996 .4988/.4996 .4988/.4996 .4988/.4996 .6238/.6246 .6238/.6246 .6238/.6246 .6238/.6246 .6238/.6246 .6238/.6246
.003 .003 .003 .003 .003 .003 .005 .005 .005 .005 .005 .005 .010 .010 .010 .010 .010 .010 .019 .019 .019 .019 .019 .019 .030 .030 .030 .030 .030 .030
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
PBC-1060 PBC-1061 PBC-1062 PBC-1063 PBC-1064 PBC-1065 PBC-1066 PBC-1067 PBC-1068 PBC-1069 PBC-1070 PBC-1071 PBC-1072 PBC-1073 PBC-1074 PBC-1075 PBC-1076 PBC-1077 PBC-1078 PBC-1079 PBC-1080 PBC-1081 PBC-1082 PBC-1083 PBC-1084 PBC-1085 PBC-1086 PBC-1087 PBC-1088 PBC-1089
Nominal OD 3
⁄4 ⁄4 ⁄4 3 ⁄4 3 ⁄4 3 ⁄4 1 1 1 1 1 1 11⁄4 11⁄4 11⁄4 11⁄4 11⁄4 11⁄4 11⁄2 11⁄2 11⁄2 11⁄2 11⁄2 11⁄2 2 2 2 2 2 2 3 3
Lgth.
Dia. Tolerance
Weight Per Inch
Pack Qty.
6 9 12 15 18 24 6 9 12 15 18 24 6 9 12 15 18 24 6 9 12 15 18 24 6 9 12 15 18 24
.7488/.7496 .7488/.7496 .7488/.7496 .7488/.7496 .7488/.7496 .7488/.7496 .9988/.9996 .9988/.9996 .9988/.9996 .9988/.9996 .9988/.9996 .9988/.9996 1.2488/1.2496 1.2488/1.2496 1.2488/1.2496 1.2488/1.2496 1.2488/1.2496 1.2488/1.2496 1.4987/1.4995 1.4987/1.4995 1.4987/1.4995 1.4987/1.4995 1.4987/1.4995 1.4987/1.4995 1.9985/1.9995 1.9985/1.9995 1.9985/1.9995 1.9985/1.9995 1.9985/1.9995 1.9985/1.9995
.043 .043 .043 .043 .043 .043 .077 .077 .077 .077 .077 .077 .120 .120 .120 .120 .120 .120 .173 .173 .173 .173 .173 .173 .308 .308 .308 .308 .308 .308
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Ceramic-Coated Aluminum Shafting Feather Shafting Pre-drilled and Tapped A
B
Pre-drilled and Tapped Item No.
PBC-1090 PBC-1091 PBC-1092 PBC-1093 PBC-1094 PBC-1095 PBC-1096 PBC-1097 PBC-1098 PBC-1099 PBC-1100 PBC-1101 PBC-1102 PBC-1103 PBC-1104 PBC-1105 PBC-1106 PBC-1107 PBC-1108 PBC-1109 PBC-1110 PBC-1111 PBC-1112 PBC-1113 PBC-1114 PBC-1115 PBC-1116 PBC-1117 PBC-1118 PBC-1119 PBC-1120 PBC-1121 PBC-1122 PBC-1123 PBC-1124 PBC-1125 PBC-1126 PBC-1127 PBC-1128 PBC-1129 PBC-1130 PBC-1131
Nominal OD 1
⁄2 ⁄2 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 3 ⁄4 3 ⁄4 3 ⁄4 3 ⁄4 3 ⁄4 3 ⁄4 1 1 1 1 1 1 11⁄4 11⁄4 11⁄4 11⁄4 11⁄4 11⁄4 11⁄2 11⁄2 11⁄2 11⁄2 11⁄2 11⁄2 2 2 2 2 2 2 1 1
Hole Spacing
Lgth.
Dia. Tolerance
A
B
Thread
Weight Per Inch
Pack Qty.
6 9 12 15 18 24 6 9 12 15 18 24 6 9 12 15 18 24 6 9 12 15 18 24 6 9 12 15 18 24 6 9 12 15 18 24 6 9 12 15 18 24
.4988/.4996 .4988/.4996 .4988/.4996 .4988/.4996 .4988/.4996 .4988/.4996 .6238/.6246 .6238/.6246 .6238/.6246 .6238/.6246 .6238/.6246 .6238/.6246 .7488/.7496 .7488/.7496 .7488/.7496 .7488/.7496 .7488/.7496 .7488/.7496 .9988/.9996 .9988/.9996 .9988/.9996 .9988/.9996 .9988/.9996 .9988/.9996 1.2488/1.2496 1.2488/1.2496 1.2488/1.2496 1.2488/1.2496 1.2488/1.2496 1.2488/1.2496 1.4987/1.4995 1.4987/1.4995 1.4987/1.4995 1.4987/1.4995 1.4987/1.4995 1.4987/1.4995 1.9985/1.9995 1.9985/1.9995 1.9985/1.9995 1.9985/1.9995 1.9985/1.9995 1.9985/1.9995
2 2 2 2 2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 4 4 4 4 4
4 4 4 4 4 4 4 4 4 4 4 4 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 8 8 8 8 8 8 8 8 8 8 8 8
6-32 6-32 6-32 6-32 6-32 6-32 8-32 8-32 8-32 8-32 8-32 8-32 10-32 10-32 10-32 10-32 10-32 10-32 1 ⁄4-20 1 ⁄4-20 1 ⁄4-20 1 ⁄4-20 1 ⁄4-20 1 ⁄4-20 5 ⁄16-18 5 ⁄16-18 5 ⁄16-18 5 ⁄16-18 5 ⁄16-18 5 ⁄16-18 3 ⁄8-16 3 ⁄8-16 3 ⁄8-16 3 ⁄8-16 3 ⁄8-16 3 ⁄8-16 1 ⁄2-13 1 ⁄2-13 1 ⁄2-13 1 ⁄2-13 1 ⁄2-13 1 ⁄2-13
.019 .019 .019 .019 .019 .019 .030 .030 .030 .030 .030 .030 .043 .043 .043 .043 .043 .043 .077 .077 .077 .077 .077 .077 .120 .120 .120 .120 .120 .120 .173 .173 .173 .173 .173 .173 .308 .308 .308 .308 .308 .308
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Note: B dimension is centered on all lengths
857
LINEAR SHAFT ASSEMBLIES & BEARINGS Linear Shaft Assemblies Aluminum - Ceramic Coated
D
E
A
F
B 12"
24"
Item No.
Item No.
Nom. Dia. 1
PBL-305 PBL-310 PBL-315 PBL-320 PBL-325 PBL-330
⁄2 ⁄4 1
3
Made from 6061-T6 aluminum with a ceramic coating to MIL-8625. The one piece integrated design eliminates assembly time. Weld spatter, paints and other contaminates will not stick to the shaft. Vibration resistant and non-magnetic. This shafting should not be used in harsh wash down environments or with ball bearings. Class "L" tolerance.
X
Y
C
Actual Dia.
+/-.002 A
B
C
D
E
F Bolt
F Hole
.4990/.4995 .7490/.7495 .9990/.9995
1.125 1.500 1.750
1.500 1.750 2.125
.250 .375 .500
.188 .250 .250
1.00 1.25 1.50
#6 #10 1 ⁄4
.169 .221 .281
X Y Hole Spacing Hole Spacing
4 6 6
Pack Qty.
2 3 3
1 1 1
Features a high load capacity. Approved for direct food contact in applications where animal fat or food approved lubricants are present. Bearing requires lubrication, but offers a middle ground coefficient of friction between ball bushing, composite/self-lubricating bearings and injection molded plastics. Coefficient of friction is .04 to .08. Dampens vibration for quiet and smooth operation - no metal to metal contact. Pillow blocks allow 360° misalignment of 1° from shaft centerline and 2° total misalignment of applications where proper alignment is difficult or self-alignment desirable. Bearing is able to withstand rapid oscillation, contamination, shock/vibration, wash downs, submersion and shaft brinelling. Works in less than ideal conditions such as granite polishing/cutting, glass cutting and abrasive polishing machinery. Minimum shaft hardness is RC35. Temperature range is -200°F to +440°F. The max. static psi is 5,000. The max. PV is 40,000. Linear Bearings Stainless Steel FDA/USDA Compliant
D B
D
A
B
A
F
C
Closed Style
C
60°
Open Style
Stainless steel shell features FDA/USDA compliant, self-lubricating PTFE composite liner. Bearings are direct drop-in replacements for inch size linear ball bushings. Designed to run on soft 300 series shafting. Minimum shaft hardness is RB25. Ideal for drug/food processing equipment and packaging equipment where direct contact would be a factor. Bearing is unaffected by wash downs, contamination or submersion. Coefficient of friction is .12 to .20. Temperature range is -400 to +375 degree Fahrenheit. The max. static psi is 1,000. Max. SFM without any load is 400. PV max. is 10,000. Closed Style
Open Style
Item No.
Item No.
F
A
B
C
D
Max. Static Load (Lbs.)
Pack Qty.
LMB-5 LMB-10 LMB-15 LMB-20
LMB-25 LMB-30 LMB-35 LMB-40
.156 .312 .438 .563
.3755 .5005 .7508 1.0008
.6250 .8750 1.2500 1.5625
.875 1.250 1.625 2.250
.562 .875 1.062 1.625
1,643 3,128 6,100 11,259
1 1 1 1
Linear Bearing Closed Style Ceramic Coated
D B
A E C
Item No.
A
B
C
D
E
Max. Static Load (Lbs.)
Pack Qty.
LMB-100 LMB-105 LMB-110 LMB-115 LMB-120 LMB-125 LMB-130
.2505 .3755 .5005 .7508 1.0008 1.2508 1.5008
.5000 .6250 .8750 1.2500 1.5625 2.0000 2.3750
.750 .875 1.250 1.625 2.250 2.625 3.000
.437 .562 .875 1.062 1.625 1.875 2.250
.018 .260 .490 .612 1.180 1.425 1.670
939 1,643 3,128 6,100 11,259 16,417 22,512
1 1 1 1 1 1 1
Note: Do not use WD-40 or silicon based spray lubricants.
Self-Aligning Pillow Blocks Closed Style Ceramic Coated
G D
K
A
M E B Item No.
LMB-300 LMB-305 LMB-310 LMB-315 LMB-320 LMB-325 LMB-330
Shaft Dia. Nom. 1
⁄4 3 ⁄8 1 ⁄2 3 ⁄4 1 11⁄4 11⁄2
Max.
+/-.003 A
B
C
.2495 .3745 .4995 .7495 .9995 1.2495 1.4994
.437 .500 .687 .937 1.187 1.500 1.750
15⁄8 13⁄4 2 23⁄4 31⁄4 4 43⁄4
13⁄16 15⁄16 111⁄16 21⁄16 213⁄16 35⁄8 4
Note: Do not use WD-40 or silicon based spray lubricants.
858
D 13
⁄16 15 ⁄16 11⁄4 13⁄4 23⁄16 213⁄16 31⁄4
F C Size
+/-.010 E
+/-.010 F
G
Bolt
1.312 1.437 1.688 2.375 2.875 3.500 4.125
.750 .875 1.000 1.250 1.750 2.000 2.500
1 11⁄8 13⁄8 17⁄8 23⁄8 3 31⁄2
#6 #6 #6 #8 #10 #10 1 ⁄4
Hole 5
⁄32 5 ⁄32 5 ⁄32 3 ⁄16 7 ⁄32 7 ⁄32 9 ⁄32
K 3
⁄4 7 ⁄8 11⁄8 19⁄16 2 21⁄2 27⁄8
Min. M 3
⁄16 3 ⁄16 1 ⁄4 5 ⁄16 3 ⁄8 7 ⁄16 1 ⁄2
Max. Static Load
Pack Qty.
939 1,643 3,128 6,100 11,259 16,417 22,512
1 1 1 1 1 1 1
LINEAR BEARINGS Simplicity Pillow Blocks Closed Style - Single and Twin Precision and Compensated Styles G D
K
A
H
J
F C
E B
These pillow blocks contain closed style bearings. H Item No.
Pacific
Nominal ID
Actual ID
Precision Style - Single 3 PBC-60 P06 ⁄8 .3750/.3760 1 PBC-61 P08 ⁄2 .5000/.5010 5 PBC-62 P10 ⁄8 .6250/.6260 3 PBC-63 P12 ⁄4 .7500/.7510 PBC-64 P16 1 1.0000/1.0010 PBC-65 P20 11⁄4 1.2500/1.2510 PBC-66 P24 11⁄2 1.5000/1.5012 PBC-67 P32 2 2.0000/2.0014 Compensated Style - Single 3 PBC-70 P06C ⁄8 .3770/.3780 1 PBC-71 P08C ⁄2 .5020/.5030 5 PBC-72 P10C ⁄8 .6270/.6280 3 PBC-73 P12C ⁄4 .7530/.7540 PBC-74 P16C 1 1.0030/1.0040 PBC-75 P20C 11⁄4 1.2540/1.2550 PBC-76 P24C 11⁄2 1.5040/1.5052 Precision Style - Twin 3 PBC-100 PW06 ⁄8 .3750/.3760 1 PBC-101 PW08 ⁄2 .5000/.5010 5 PBC-102 PW10 ⁄8 .6250/.6260 3 PBC-103 PW12 ⁄4 .7500/.7510 PBC-104 PW16 1 1.0000/1.0010
J
K
Max. Load (Lbs.)
Pack Qty.
⁄32 ⁄32 ⁄16 3 ⁄16 7 ⁄32 7 ⁄32 9 ⁄32 13 ⁄32
.188 .250 .281 .313 .375 .438 .500 .625
.875 1.125 1.438 1.563 1.938 2.500 2.875 3.625
510 975 1,470 1,905 3,525 5,145 7,050 12,525
1 1 1 1 1 1 1 1
#6 #6 #8 #8 #10 #10 1 ⁄4
5
⁄32 ⁄32 ⁄16 3 ⁄16 7 ⁄32 7 ⁄32 9 ⁄32
.188 .250 .281 .313 .375 .438 .500
.875 1.125 1.438 1.563 1.938 2.500 2.875
510 975 1,470 1,905 3,525 5,145 7,050
1 1 1 1 1 1 1
#6 #6 #8 #8 #10
5
.188 .250 .281 .313 .375
.875 1.125 1.438 1.563 1.938
1,020 1,950 2,940 3,810 7,050
1 1 1 1 1
J
K
Max. Load (Lbs.)
Pack Qty.
.250 .281 .313 .375 .500 .250 .281 .313 .375 .500 .250 .281 .313 .375
.313 .375 .438 .563 .750 .313 .375 .438 .563 .750 .313 .375 .438 .563
975 1,470 1,905 3,525 7,050 975 1,470 1,905 3,525 7,050 1,950 2,940 3,810 7,050
1 1 1 1 1 1 1 1 1 1 1 1 1 1
+/-.001 A
B
C
D
+/-.010 E
+/-.010 F
G
Bolt
.500 .687 .875 .937 1.187 1.500 1.750 2.125
1.75 2.00 2.50 2.75 3.25 4.00 4.75 6.00
1.313 1.688 1.938 2.063 2.813 3.625 4.000 5.000
.938 1.250 1.625 1.750 2.188 2.813 3.250 4.063
1.437 1.688 2.125 2.375 2.875 3.500 4.125 5.250
.875 1.000 1.125 1.250 1.750 2.000 2.500 3.250
1.125 1.375 1.750 1.875 2.375 3.000 3.500 4.500
#6 #6 #8 #8 #10 #10 1 ⁄4 3 ⁄8
.500 .687 .875 .937 1.187 1.500 1.750
1.75 2.00 2.50 2.75 3.25 4.00 4.75
1.313 1.688 1.938 2.063 2.813 3.625 4.000
.938 1.250 1.625 1.750 2.188 2.813 3.250
1.437 1.688 2.125 2.375 2.875 3.500 4.125
.875 1.000 1.125 1.250 1.750 2.000 2.500
1.125 1.375 1.750 1.875 2.375 3.000 3.500
.500 .687 .875 .937 1.187
1.75 2.00 2.50 2.75 3.25
2.75 3.50 4.00 4.50 6.00
.938 1.250 1.625 1.750 2.188
1.437 1.688 2.125 2.375 2.875
2.250 2.500 3.000 3.500 4.500
1.125 1.375 1.750 1.875 2.375
Hole 5 5 3
5 3
⁄32 ⁄32 ⁄16 3 ⁄16 7 ⁄32 5 3
Simplicity Pillow Blocks Open Style - Single and Twin Precision and Compensated Styles G MIN GAP
K J
D A
H F C
E B
These pillow blocks contain open style bearings. Item No.
PBC-80 PBC-81 PBC-82 PBC-83 PBC-85 PBC-90 PBC-91 PBC-92 PBC-93 PBC-95 PBC-110 PBC-111 PBC-112 PBC-113
Pacific
PN08 PN10 PN12 PN16 PN24 PN08C PN10C PN12C PN16C PN24C PWN08 PWN10 PWN12 PWN16
Nominal ID 1
⁄2 ⁄8 ⁄4 1 11⁄2 1 ⁄2 5 ⁄8 3 ⁄4 1 11⁄2 1 ⁄2 5 ⁄8 3 ⁄4 1 5 3
Actual ID
.5000/.5010 .6250/.6260 .7500/.7510 1.0000/1.0010 1.5000/1.5012 .5020/.5030 .6270/.6280 .7530/.7540 1.0030/1.0040 1.5040/1.5052 .5000/.5010 .6250/.6260 .7500/.7510 1.0000/1.0010
+/-.001 A
.687 .875 .937 1.187 1.750 .687 .875 .937 1.187 1.750 .687 .875 .937 1.187
B
2.00 2.50 2.75 3.25 4.75 2.00 2.50 2.75 3.25 4.75 2.00 2.50 2.75 3.25
C
1.688 1.938 2.063 2.813 4.000 1.688 1.938 2.063 2.813 4.000 3.500 4.000 4.500 6.000
D
1.125 1.438 1.563 1.938 2.875 1.125 1.438 1.563 1.938 2.875 1.125 1.438 1.563 1.938
+/-.010 E
1.688 2.125 2.375 2.875 4.125 1.688 2.125 2.375 2.875 4.125 1.688 2.125 2.375 2.875
+/-.010 F
1.000 1.125 1.250 1.750 2.500 1.000 1.125 1.250 1.750 2.500 2.500 3.000 3.500 4.500
H Bolt
G
1.375 1.750 1.875 2.375 3.500 1.375 1.750 1.875 2.375 3.500 1.375 1.750 1.875 2.375
Hole 5
#6 #8 #8 #10 1 ⁄4 #6 #8 #8 #10 1 ⁄4 #6 #8 #8 #10
⁄32 ⁄16 ⁄16 7 ⁄32 9 ⁄32 5 ⁄32 3 ⁄16 3 ⁄16 7 ⁄32 9 ⁄32 5 ⁄32 3 ⁄16 3 ⁄16 7 ⁄32 3 3
Simplicity Flange Mounted Self-Aligning Bearings B C
L E
F
Self Aligning in All Directions
D
BC
Clear Anodized 6061-T6 Aluminum
Item No.
These Simplicity flange mounted bearings with FrelonGOLD provide all the same self lubrication features as the pillow block mounted bearings. Bearing is FrelonGOLD enclosed in a flange housing made of 6061-T6 aluminum. Double length has two internal mounted bearings.
Pacific
Single Length PBC-305 SFP-08 PBC-310 SFP-12 PBC-315 SFP-16 Twin Length PBC-320 DFP-08 PBC-325 DFP-12 PBC-330 DFP-16
Nominal Diameter 1
B
C
D
E
F
L
Max. Static Load Pack (Lbs.) Qty.
⁄2 ⁄4 1
1.63 1.250 1.25 2.38 1.750 1.75 2.75 2.125 2.25
.250 #8 1.687 .375 #10 2.067 .500 1⁄4 2.812
975 1,470 1,905
1 1 1
1
1.63 1.250 1.25 2.38 1.750 1.75 2.75 2.125 2.25
.250 #8 3.375 .375 #10 4.188 .500 1⁄4 5.625
1,950 2,940 3,810
1 1 1
3
⁄2 ⁄4 1
3
859
LINEAR BEARINGS Square Linear Bearings
Frelon bearing liner fixed on 2 sides
Adjustable bearing plugs inserted on 4 opposite sides
Adjustable bearing plugs inserted on 2 opposite sides
Two Sided Adjustable
Four Sided Adjustable
These square bearings maintain radial integrity and can eliminate the need for parallel shafting. The bearings are made from 6061-T6 aluminum with anodized finish. Equipped with bearing plugs that run on a single square shaft, eliminating costly components. The threaded adjustable bearing plugs are made from 316 stainless steel with self-lubricating Frelon® wear pads and are designed to run on the stainless shafting shown below.
Two Sided Adjustable Four Sided Adjustable Item No.
Item No.
ID Sq.
PBC-405 PBC-415 PBC-425 PBC-435 PBC-450
PBC-410 PBC-420 PBC-430 PBC-440 —
OD Sq.
Load Capacity (Lbs.)
Lgth.
Pack Qty.
1 13⁄4 21⁄4 920 1 13⁄4 4 920 11⁄2 25⁄16 31⁄8 1,840 11⁄2 25⁄16 6 1,840 Replacement Frelon Bearing Plug
1 1 1 1 1
Square Shafting
Made from 304 stainless for high corrosion resistance. Buffed and polished to provide an excellent running surface for the above bearings. 1" x 1"
11⁄2" x 11⁄2"
Item No.
Item No.
PBC-460 PBC-475 PBC-465 PBC-480 PBC-470 PBC-485
Lgth. (Feet)
Pack Qty.
2 3 4
1 1 1
Square Clamps and Flange Bases
F E H
G A
+G
F
D
C
B HC
Square Clamps
D
B
E
A
J
E
Flange Bases Item No.
Made from cast 356-T6 aluminum for good strength and corrosion resistance.
860
A
B
C
D
Square Clamps PBC-490 1.00 .984 1.968 .630 PBC-495 1.50 1.338 2.677 .630 Flange Bases PBC-500 1.00 1 1.890 2.362 PBC-505 1.50 1.25 2.440 2.756
E
F
G
H
J
Pack Qty.
2.362 2.362
.197 .197
.200 .200
.787 2.953
— —
1 1
2.520 2.992
.472 .551
.256 .256
3.228 2.874 3.740 3.347
1 1
BEARING ACCESSORIES Seals for Closed Type Bearings
Internal Retaining Rings (Type PR)
OD A
T Double acting seals for Super Smart, Super and Precision closed type ball bushing bearings. Item No.
Thomson
For Use With Thomson Bearing No.
TLM-250 S-250 Super-4 or 4812 TLM-255 S-375 Super-6 or 61014 TLM-260 S-500 Super-8 or 81420 TLM-265 S-625 SSU-10 or Super-10 or 101824 TLM-270 S-750 SSU-12 or Super-12 or 122026 TLM-275 S-1000 SSU-16 or Super-16 or 162536 TLM-280 S-1250 SSU-20 or Super-20 or 203242 TLM-285 S-1500 SSU-24 or Super-24 or 243848
B
Push in retaining rings are for use with Super Smart, Super and Precision ball bushing bearings, closed type. Each retaining ring is installed inside the housing bore at each end of the bearing.
Race Dia.
T
OD
Pack Qty.
Item No.
Thomson
For Use With Thomson Bearing No.
A
B
Pack Qty.
.250 .375 .500 .625 .750 1.000 1.250 1.500
.125 .125 .125 .125 .125 .187 .375 .375
.504 .629 .879 1.129 1.254 1.567 2.004 2.379
1 1 1 1 1 1 1 1
TLM-150 TLM-155 TLM-160 TLM-165 TLM-170 TLM-175 TLM-180 TLM-185
PR250 PR375 PR500 PR625 PR750 PR1000 PR1250 PR1500
Super-4 or 4812 Super-6 or 61014 Super-8 or 81420 SSU-10 or Super-10 or 101824 SSU-12 or Super-12 or 122026 SSU-16 or Super-16 or 162536 SSU-20 or Super-20 or 203242 SSU-24 or Super-24 or 243848
.500 .625 .875 1.125 1.250 1.563 2.000 2.375
.060 .060 .080 .080 .080 .080 .080 .100
1 1 1 1 1 1 1 1
Note: Dimension B minimum end space required.
Seals For Open Type Bearings
External Retaining Rings (Type C)
OD
OD
T T
Double acting seals for Super Smart, Super and Precision open type ball bushing bearings. Item No.
Thomson
TLM-305 TLM-310 TLM-315 TLM-320 TLM-325 TLM-330
OPN-S-500 OPN-S-625 OPN-S-750 OPN-S-1000 OPN-S-1250 OPN-S-1500
For Use With Thomson Bearing No.
Race Dia.
T
OD
Super-8 or 81420 .500 .125 .879 SSU-10 or Super-10 or 101824 .625 .125 1.129 SSU-12 or Super-12 or 122026 .750 .125 1.254 SSU-16 or Super-16 or 162536 1.000 .187 1.567 SSU-20 or Super-20 or 203242 1.250 .375 2.004 SSU-24 or Super-24 or 243848 1.500 .375 2.379
Pack Qty.
1 1 1 1 1 1
Fits into the retaining ring grooves on the outside diameter of Super Smart, Super and Precision ball bushing bearings to provide external mounting retention. Item No.
Thomson
For Use With Thomson Bearing No.
T
OD
Pack Qty.
TLM-205 TLM-210 TLM-215 TLM-220 TLM-225 TLM-230 TLM-235 TLM-240
C250 C375 C500 C625 C750 C1000 C1250 C1500
Super-4 or 4812 Super-6 or 61014 Super-8 or 81420 SSU-10 or Super-10 or 101824 SSU-12 or Super-12 or 122026 SSU-16 or Super-16 or 162536 SSU-20 or Super-20 or 203242 SSU-24 or Super-24 or 243848
.035 .035 .042 .050 .050 .062 .062 .078
.550 .673 .923 1.180 1.301 1.620 2.040 2.429
1 1 1 1 1 1 1 1
Bearing Grease
LinearLube is designed for use in bearing applications. It is 100% synthetic grease with concentrated PTFE particles. It will not volitize or oxidize at high operating temperatures or form corrosive deposits. Contains no petroleum products. It is non-toxic (FDA listed and USDA rated H1, suitable for incidental contact with food or potable water) and non-polluting. No adverse effects on plastics. Operates effectively from -65 degree Fahrenheit to +450 degree Fahrenheit. 141â „2 oz. tube. Item No.
Description
Pack Qty.
LL-1
Linear Lube Bearing Grease
1
861
MOUNTED BEARINGS These mounted bearings are used extensively in fabricating equipment because they are easy to fit, maintain and replace. Made of cast iron housings with a grease fitting for easy lubrication. Pillow block style comes in two types, standard height and low center height.
K
L H A D C
E min. E max B
Pillow Block Standard Duty Standard Center Height Set Screw Locking - Narrow Inner Ring - M-Seal Item No.
Bore
Load Rating
A
B
C
D
SKF-402 SKF-404 SKF-407 SKF-408 SKF-409 SKF-411 SKF-412 SKF-414 SKF-415 SKF-416 SKF-410 SKF-405 SKF-413
3 ⁄4 15 ⁄16 13⁄16 11⁄4 11⁄4 17⁄16 11⁄2 13⁄4 115⁄16 2 13⁄8 1 111⁄16
2,860 3,150 4,390 4,390 5,740 5,740 6,910 7,470 7,900 7,900 5,740 3,150 7,470
15⁄16 17⁄16 111⁄16 111⁄16 17⁄8 17⁄8 21⁄8 21⁄8 21⁄4 21⁄2 17⁄8 17⁄16 21⁄8
5 51⁄8 6 6 65⁄16 65⁄16 73⁄8 73⁄8 8 85⁄8 65⁄16 51⁄8 73⁄8
11⁄4 113⁄32 19⁄16 19⁄16 125⁄32 125⁄32 17⁄8 17⁄8 21⁄8 23⁄16 125⁄32 113⁄32 17⁄8
⁄ ⁄ ⁄32 21 ⁄32 3 ⁄4 3 ⁄4 13 ⁄16 13 ⁄16 7 ⁄8 15 ⁄16 3 ⁄4 5 ⁄8 13 ⁄16
9
16 5 8
21
E Min.
E Max.
H
K
315⁄32 311⁄16 41⁄4 41⁄4 411⁄16 411⁄16 55⁄16 55⁄16 57⁄8 63⁄8 411⁄16 311⁄16 55⁄16
43⁄16 411⁄32 5 5 51⁄4 51⁄4 6 6 61⁄2 71⁄8 51⁄4 411⁄32 6
217⁄32 23⁄4 37⁄32 37⁄32 321⁄32 321⁄32 47⁄32 47⁄32 41⁄2 5 321⁄32 23⁄4 47⁄32
9 32 5 16 23 64 23 64 3 8 3 8 7 16 7 16 7 16 1 2 3 8 5 16 7 16
⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄
L 23
Pack Qty.
⁄32 ⁄32 ⁄8 7 ⁄8 1 1 19⁄32 19⁄32 117⁄64 11⁄32 1 25 ⁄32 19⁄32
1 1 1 1 1 1 1 1 1 1 1 1 1
25 7
Pillow Block Standard Duty Low Center Height Wide Width - ConCentra Lock Air Handling Unit Item No.
Bore
Load Rating
A
B
C
SKF-8790 SKF-8800 SKF-8805 SKF-8810 SKF-8815 SKF-8820 SKF-8825 SKF-8830
1 11⁄4 13⁄8 17⁄16 11⁄2 111⁄16 23⁄16 27⁄16
3,150 5,700 5,700 5,700 6,900 7,470 9,800 11,800
15⁄16 113⁄16 113⁄16 113⁄16 115⁄16 21⁄16 27⁄16 211⁄16
51⁄8 65⁄16 65⁄16 65⁄16 67⁄8 73⁄8 85⁄8 91⁄2
17⁄16 13⁄4 13⁄4 13⁄4 17⁄8 17⁄8 23⁄8 23⁄8
E Min.
E Max.
H
K
L
Pack Qty.
⁄8 3 ⁄4 3 ⁄4 3 ⁄4 3 ⁄4 13 ⁄16 15 ⁄16 1
311⁄16 411⁄16 411⁄16 411⁄16 415⁄16 55⁄16 63⁄8 71⁄16
45⁄16 51⁄4 51⁄4 51⁄4 53⁄4 6 71⁄8 715⁄16
23⁄4 311⁄16 311⁄16 311⁄16 37⁄8 41⁄4 5 51⁄2
11⁄8 11⁄4 11⁄4 11⁄4 15⁄16 13⁄8 17⁄16 11⁄2
15⁄8 17⁄8 17⁄8 17⁄8 21⁄16 2 21⁄4 25⁄16
1 1 1 1 1 1 1 1
D
E Min.
E Max.
H
L
Pack Qty.
15
3
17
D 5
Pillow Block Standard Duty Standard Center Height Eccentric Locking - Narrow Inner Ring - M-Seal Item No.
SKF-8610 SKF-8615 SKF-8620 SKF-8625 SKF-8630 SKF-8635 SKF-8640 SKF-8645 SKF-8650 SKF-8655 SKF-8670 SKF-8675 SKF-8660 SKF-8665
Bore 3
⁄4 ⁄8 ⁄16 1 13⁄16 11⁄4 11⁄4 13⁄8 17⁄16 11⁄2 2 23⁄16 111⁄16 15 1 ⁄16 7
15
Load Rating
2,860 3,150 3,150 3,150 4,390 4,390 5,740 5,740 5,740 6,910 9,810 9,810 7,470 7,900
A 5
1 ⁄16 17⁄16 17⁄16 17⁄16 111⁄16 111⁄16 17⁄8 17⁄8 17⁄8 115⁄16 21⁄2 21⁄2 21⁄8 21⁄4
B
C
5 51⁄8 51⁄8 51⁄8 6 6 65⁄16 65⁄16 65⁄16 629⁄32 85⁄8 85⁄8 73⁄8 8
1
1 ⁄4 113⁄32 113⁄32 113⁄32 19⁄16 19⁄16 125⁄32 125⁄32 125⁄32 129⁄32 23⁄16 23⁄16 17⁄8 21⁄8
9
⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄
16 5 8 5 8 5 8 21 32 21 32 3 4 3 4 3 4 3 4 15 16 15 16 13 16 7 8
3 ⁄32 311⁄16 311⁄16 311⁄16 41⁄4 41⁄4 411⁄16 411⁄16 411⁄16 415⁄16 63⁄8 63⁄8 55⁄16 57⁄8
4 ⁄16 411⁄32 411⁄32 411⁄32 5 5 51⁄4 51⁄4 51⁄4 53⁄4 71⁄8 71⁄8 6 61⁄2
2 ⁄32 23⁄4 23⁄4 23⁄4 37⁄32 37⁄32 321⁄32 321⁄32 321⁄32 329⁄32 5 5 47⁄32 41⁄2
E Min.
E Max.
H
55⁄16 57⁄8 63⁄8 71⁄16 71⁄2 81⁄2
6 61⁄2 71⁄8 715⁄16 81⁄2 91⁄2
47⁄32 41⁄2 5 51⁄2 6 631⁄32
K 9
⁄32 ⁄32 ⁄32 9 ⁄32 11 ⁄32 11 ⁄32 3 ⁄8 3 ⁄8 3 ⁄8 7 ⁄16 15 ⁄32 15 ⁄32 7 ⁄16 7 ⁄16 9 9
15
⁄16 ⁄16 ⁄16 15 ⁄16 11⁄16 11⁄16 15⁄32 15⁄32 15⁄32 17⁄32 17⁄16 17⁄16 19⁄32 19⁄32
1 1 1 1 1 1 1 1 1 1 1 1 1 1
L
Pack Qty.
13⁄16 19⁄32 15⁄16 19⁄16 19⁄16 17⁄8
1 1 1 1 1 1
15 15
Pillow Block Medium Duty Standard Center Height Wide Width - ConCentra Lock Air Handling Unit Item No.
Bore
Load Rating
A
B
C
SKF-8835 SKF-8840 SKF-8845 SKF-8850 SKF-8855 SKF-8860
17⁄16 111⁄16 115⁄16 23⁄16 27⁄16 215⁄16
6,910 7,900 9,810 11,900 14,000 16,400
21⁄8 21⁄4 21⁄2 23⁄4 3 31⁄2
73⁄8 8 85⁄8 91⁄2 101⁄8 12
13⁄4 21⁄8 23⁄16 21⁄2 25⁄8 3
862
D 13
⁄16 7 ⁄8 15 ⁄16 11⁄16 11⁄2 17⁄8
K 3
⁄4 3 ⁄4 7 ⁄8 1 13⁄16 13⁄16
MOUNTED BEARINGS These mounted bearings are used extensively in fabricating equipment because they are easy to fit, maintain and replace. Made of cast iron housings with a grease fitting for easy lubrication. Pillow block style comes in two types, standard height and low center height.
K
L H A D
Pillow Block Standard Duty Standard Center Height Set Screw Locking - Wide Inner Bearing - M-Seal and Flingers Item No.
SKF-8520 SKF-8525 SKF-8530 SKF-8535 SKF-8540 SKF-8545 SKF-8550 SKF-8555 SKF-8560 SKF-8565 SKF-8570 SKF-8575 SKF-8580 SKF-8585 SKF-8590 SKF-8595 SKF-8600 SKF-8605
Bore 1
⁄2 ⁄8 ⁄4 7 ⁄8 15 ⁄16 1 11⁄8 13⁄16 11⁄4 11⁄4 13⁄8 17⁄16 11⁄2 111⁄16 115⁄16 2 23⁄16 27⁄16 5 3
Load Rating
2,150 2,150 2,860 3,150 3,150 3,150 4,390 4,390 4,390 5,740 5,740 5,740 6,910 7,470 7,900 9,810 9,810 11,900
A
B
C
1 ⁄16 13⁄16 15⁄16 17⁄16 17⁄16 17⁄16 111⁄16 111⁄16 111⁄16 17⁄8 17⁄8 17⁄8 115⁄16 21⁄8 21⁄4 21⁄2 21⁄2 211⁄16
5 5 5 51⁄8 51⁄8 51⁄8 6 6 6 65⁄16 65⁄16 65⁄16 629⁄32 73⁄8 8 85⁄8 85⁄8 91⁄2
1
A
B
7
1
3
1 ⁄4 11⁄4 11⁄4 113⁄32 113⁄32 113⁄32 19⁄16 19⁄16 19⁄16 125⁄32 125⁄32 125⁄32 125⁄32 17⁄8 21⁄8 23⁄16 23⁄16 21⁄2
C
E min. E max B
D 9
E Min.
E Max.
H
15
3
7
K 15
⁄16 ⁄16 ⁄16 5 ⁄8 5 ⁄8 5 ⁄8 21 ⁄32 21 ⁄32 21 ⁄32 3 ⁄4 3 ⁄4 3 ⁄4 3 ⁄4 13 ⁄16 7 ⁄8 15 ⁄16 15 ⁄16 1
3 ⁄32 315⁄32 315⁄32 311⁄16 311⁄16 311⁄16 41⁄4 41⁄4 41⁄4 411⁄16 411⁄16 411⁄16 415⁄16 55⁄16 57⁄8 63⁄8 63⁄8 71⁄16
4 ⁄16 43⁄16 43⁄16 411⁄32 411⁄32 411⁄32 5 5 5 51⁄4 51⁄4 51⁄4 53⁄4 6 61⁄2 71⁄8 71⁄8 715⁄16
2 ⁄32 27⁄32 217⁄32 23⁄4 23⁄4 23⁄4 37⁄32 37⁄32 37⁄32 321⁄32 321⁄32 321⁄32 329⁄32 47⁄32 41⁄2 5 5 57⁄16
C
D
E Min.
E Max.
13
5
⁄8 ⁄32 ⁄4 3 ⁄4 3 ⁄4 13 ⁄16 7 ⁄8 15 ⁄16 11⁄32 11⁄8 19⁄32
11
3 ⁄16 41⁄4 411⁄16 411⁄16 415⁄16 55⁄16 57⁄8 63⁄8 71⁄16 71⁄2 8
5
4 ⁄16 5 51⁄4 51⁄4 53⁄4 6 61⁄2 71⁄8 715⁄16 81⁄2 9
D
E Min.
E Max
H
K
15
3
17
1
9 9
L 5
Pack Qty.
⁄32 ⁄32 ⁄2 9 ⁄16 9 ⁄16 9 ⁄16 5 ⁄8 5 ⁄8 5 ⁄8 11 ⁄16 11 ⁄16 11 ⁄16 3 ⁄4 3 ⁄4 3 ⁄4 7 ⁄8 7 ⁄8 1
⁄8 ⁄8 ⁄32 25 ⁄32 25 ⁄32 25 ⁄32 7 ⁄8 7 ⁄8 7 ⁄8 1 1 1 13⁄16 13⁄16 19⁄32 15⁄16 15⁄16 19⁄16
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
H
K
L
Pack Qty.
3
1
5
15 1
5
23
Pillow Block Standard Duty Standard Center Height Wide Width - ConCentra Lock Air Handling Unit Item No.
SKF-8735 SKF-8740 SKF-8745 SKF-8750 SKF-8755 SKF-8760 SKF-8765 SKF-8770 SKF-8775 SKF-8780 SKF-8785
Bore
1 13⁄16 11⁄4 17⁄16 11⁄2 111⁄16 115⁄16 23⁄16 27⁄16 211⁄16 215⁄16
Load Rating
3,150 4,350 5,700 5,700 6,900 7,470 7,900 9,800 11,800 14,000 14,800
1 ⁄16 111⁄16 17⁄8 17⁄8 115⁄16 21⁄8 21⁄4 21⁄2 23⁄4 3 31⁄4
5 ⁄8 6 65⁄16 65⁄16 657⁄64 73⁄8 8 85⁄8 97⁄16 1015⁄64 1063⁄64
1 ⁄32 19⁄16 125⁄32 125⁄32 157⁄64 129⁄32 21⁄8 23⁄8 223⁄64 29⁄16 213⁄16
21 3
2 ⁄4 37⁄32 321⁄32 321⁄32 329⁄32 47⁄32 41⁄2 5 51⁄2 57⁄8 617⁄32
1 ⁄8 13⁄16 11⁄4 11⁄4 15⁄16 13⁄8 13⁄8 17⁄16 11⁄2 11⁄2 15⁄8
1 ⁄8 13⁄4 17⁄8 17⁄8 21⁄16 2 21⁄8 21⁄4 25⁄16 23⁄8 21⁄2
1 1 1 1 1 1 1 1 1 1 1
L
Pack Qty.
Pillow Block Standard Duty Standard Center Height Set Screw Lock - Wide Width - M-Seal and Flinger Air Handling Unit Item No.
SKF-8680 SKF-8685 SKF-8690 SKF-8695 SKF-8700 SKF-8705 SKF-8710 SKF-8715 SKF-8720 SKF-8725 SKF-8730
Bore 3
⁄4 1 13⁄16 17⁄16 11⁄2 111⁄16 115⁄16 2 23⁄16 27⁄16 215⁄16
Load Rating
2,860 3,150 4,390 5,740 6,910 7,470 7,900 9,810 9,810 11,900 14,900
A 5
1 ⁄16 17⁄16 111⁄16 17⁄8 115⁄16 21⁄8 21⁄4 21⁄2 21⁄2 211⁄16 31⁄4
B
C
5 51⁄8 6 65⁄16 629⁄32 73⁄8 8 85⁄8 85⁄8 91⁄2 103⁄4
1
1 ⁄4 113⁄32 19⁄16 125⁄32 129⁄32 17⁄8 21⁄8 23⁄16 23⁄16 21⁄2 225⁄32
9
⁄ ⁄ ⁄32 3 ⁄4 3 ⁄4 13 ⁄16 7 ⁄8 15 ⁄16 15 ⁄16 1 11⁄4 16 5 8
21
3 ⁄32 311⁄16 41⁄4 411⁄16 415⁄16 55⁄16 57⁄8 63⁄8 63⁄8 71⁄16 8
4 ⁄16 411⁄32 5 51⁄4 53⁄4 6 61⁄2 71⁄8 71⁄8 715⁄16 9
2 ⁄32 23⁄4 37⁄32 321⁄32 329⁄32 47⁄32 41⁄2 5 5 57⁄16 61⁄2
E Min.
E Max.
H
315⁄32 311⁄16 311⁄16 311⁄16 41⁄4 411⁄16
43⁄16 411⁄32 411⁄32 411⁄32 5 51⁄4
215⁄32 25⁄8 25⁄8 25⁄8 33⁄32 319⁄32
⁄2 ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ 1 11⁄16 9
16 5 8 11 16 3 4 3 4 3 4 7 8 7 8
23
⁄32 ⁄32 ⁄8 1 13⁄16 13⁄16 19⁄32 15⁄16 15⁄16 19⁄16 113⁄16
1 1 1 1 1 1 1 1 1 1 1
L
Pack Qty.
23 7
Pillow Block Standard Duty Low Center Height Set Screw Locking - Narrow Inner Ring - M-Seal Item No.
SKF-421 SKF-422 SKF-423 SKF-424 SKF-426 SKF-428
Bore 3
⁄4 7 ⁄8 15 ⁄16 1 13⁄16 11⁄4
Load Rating
A
B
C
2,860 3,150 3,150 3,150 4,390 5,740
11⁄4 15⁄16 15⁄16 15⁄16 19⁄16 113⁄16
5 51⁄8 51⁄8 51⁄8 6 65⁄16
11⁄4 113⁄32 113⁄32 113⁄32 19⁄16 125⁄32
D 1
⁄2 1 ⁄2 1 ⁄2 1 ⁄2 17 ⁄32 11 ⁄16
K 9
⁄32 5 ⁄16 5 ⁄16 5 ⁄16 23 ⁄64 3 ⁄8
23
⁄32 25 ⁄32 25 ⁄32 25 ⁄32 7 ⁄8 1
1 1 1 1 1 1
863
MOUNTED BEARINGS Standard duty, high-grade cast iron. Solid foot housing design. Wide inner ring bearing. Relubricatable unit with anti-rotation pin. These mounted bearings are used extensively in fabricated equipment because they are easy to fit, maintain and replace. They are sealed and pre-greased, and under normal conditions require no further lubrications (grease fitting is supplied for additional lubrication under adverse conditions.) Housing is made from cast iron. All bearings below have set screw shaft locking. Flange Units - Standard Two Bolt
E
Y AB K
C
J
D
Item No.
Bearing No.
PRB-118 PRB-119 PRB-120 PRB-185 PRB-186 PRB-121 PRB-122 PRB-188 PRB-123 PRB-190 PRB-191 PRB-192 PRB-124 PRB-194 PRB-125
UCFT201-8 UCFT202-10 UCFT204-12 UCFT205-14 UCFT205-15 UCFT205-16 UCFT206-17 UCFT206-19 UCFT206-20 UCFT207-20 UCFT207-22 UCFT207-23 UCFT208-24 UCFT209-27 UCFT210-30
Bore Size 1
⁄2 5 ⁄8 3 ⁄4 7 ⁄8 15 ⁄16 1 11⁄16 13⁄16 11⁄4 11⁄4 13⁄8 17⁄16 11⁄2 111⁄16 17⁄8
Load Rate
A
B
2,900 2,900 2,900 3,150 3,150 3,150 4,390 4,390 4,390 5,740 5,740 5,740 7,340 7,470 7,900
37⁄8 37⁄8 47⁄16 51⁄8 51⁄8 51⁄8 513⁄16 513⁄16 513⁄16 611⁄32 611⁄32 611⁄32 67⁄8 713⁄32 73⁄4
3 3 317⁄16 357⁄64 357⁄64 357⁄64 419⁄32 419⁄32 419⁄32 51⁄8 51⁄8 51⁄8 521⁄32 527⁄32 21⁄2
D
E
J
K
Y
Pack Qty.
1 1 15 ⁄16 11⁄64 11⁄64 11⁄64 15⁄32 15⁄32 15⁄32 13⁄16 13⁄16 13⁄16 113⁄32 13⁄8 117⁄32
1.32 1.32 1.31 1.41 1.41 1.41 1.58 1.58 1.58 1.75 1.75 1.75 2.02 2.06 2.15
21⁄8 21⁄8 23⁄8 211⁄16 211⁄16 211⁄16 35⁄32 35⁄32 35⁄32 317⁄32 317⁄32 317⁄32 315⁄16 41⁄4 417⁄32
.594 .594 .591 .630 .630 .630 .709 .709 .709 .748 .748 .748 .828 .866 .866
.094 .094 .091 .067 .067 .067 .083 .083 .083 .059 .059 .059 .080 .118 .118
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
C 7
⁄16 7 ⁄16 7 ⁄16 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 9 ⁄16 9 ⁄16 9 ⁄16 9 ⁄16 19 ⁄32 19 ⁄32
Flange Units - Standard Four Bolt
E
B
A
K
C
Flange Unit Standard Four Bolt
D
Item No.
Bearing No.
PRB-126 PRB-127 PRB-128 PRB-129 PRB-168 PRB-130 PRB-170 PRB-171 PRB-131 PRB-132 PRB-133 PRB-134 PRB-135 PRB-177 PRB-178 PRB-136 PRB-179 PRB-137 PRB-181
UCF201-8 UCF202-10 UCF204-12 UCF205-14 UCF205-15 UCF205-16 UCF206-18 UCF206-19 UCF206-20 UCF207-20 UCF207-22 UCF207-23 UCF208-24 UCF209-27 UCF209-28 UCF210-30 UCF210-31 UCF210-32 UCF211-35
Bore Size 1
⁄2 5 ⁄8 3 ⁄4 7 ⁄8 15 ⁄16 1 11⁄8 13⁄16 11⁄4 11⁄4 13⁄8 17⁄16 11⁄2 111⁄16 13⁄4 17⁄8 115⁄16 2 23⁄16
Load Rate
A
B
2,900 2,900 2,900 3,150 3,150 3,150 4,390 4,390 4,390 5,740 5,740 5,740 7,340 7,470 7,470 7,900 7,900 7,900 9,810
3 3 33⁄8 33⁄4 33⁄4 33⁄4 41⁄4 41⁄4 41⁄4 419⁄32 419⁄32 419⁄32 51⁄8 53⁄8 53⁄8 55⁄8 55⁄8 55⁄8 63⁄8
21⁄8 21⁄8 21⁄2 23⁄4 23⁄4 23⁄4 31⁄4 31⁄4 31⁄4 35⁄8 35⁄8 35⁄8 4 41⁄8 41⁄8 43⁄8 43⁄8 43⁄8 51⁄8
D
E
K
Pack Qty.
1 1 1 11⁄16 13⁄16 11⁄16 19⁄32 19⁄32 15⁄64 13⁄16 13⁄16 13⁄16 113⁄32 119⁄32 119⁄32 19⁄16 13⁄4 19⁄16 17⁄8
1.31 1.31 1.31 1.41 117⁄32 1.41 121⁄32 121⁄32 1.59 1.75 1.75 1.75 2.02 27⁄64 27⁄64 2.031 219⁄64 2.031 27⁄16
.592 .592 .592 .631 3 ⁄4 .631 25 ⁄32 25 ⁄32 .720 .750 .750 .750 .834 29 ⁄32 29 ⁄32 .873 11⁄32 .873 15⁄32
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
C 3
⁄8 3 ⁄8 7 ⁄16 1 ⁄2 5 ⁄8 1 ⁄2 19 ⁄32 19 ⁄32 9 ⁄16 19 ⁄32 19 ⁄32 19 ⁄32 19 ⁄32 11 ⁄16 11 ⁄16 5 ⁄8 25 ⁄32 5 ⁄8 37 ⁄32
U
Two Bolt Flange
P
M
B
L
K A
T
C
Two Bolt Flange Item No.
INA-110 INA-115 INA-135
Bore 1
⁄2 ⁄8 1
5
A
B
1
29
2 ⁄4 21⁄4 225⁄32
3 ⁄32 329⁄32 51⁄8
C
K
13
15
13
15
15
15
⁄32 ⁄32 ⁄32
L
M
3
⁄32 ⁄32 ⁄32
1 ⁄32 13⁄32 111⁄32
P
T 15
21
3 3 329⁄32
⁄32 ⁄32 ⁄4
⁄16 15 ⁄16 13⁄32
21
3
U 9
1 ⁄32 19⁄32 117⁄32
Pack Qty.
1 1 1
Four Bolt Flange
Item No.
Bore
A
B
C
1
5
19
1
INA-140 1 ⁄8 INA-150 11⁄4 INA-185 115⁄16
3 ⁄32 321⁄32 419⁄32
5 ⁄32 65⁄32 717⁄32
K 15
⁄2 ⁄ ⁄
⁄ ⁄ ⁄
16 5 8
M
M
1
19
1 ⁄2 111⁄16 21⁄32
32 9 16 21 32
9
L
P 25
4 ⁄32 51⁄8 63⁄16
⁄32 27 ⁄32 13⁄32
T
U
9
21
1 ⁄32 13⁄8 111⁄16
1 ⁄32 127⁄32 23⁄8
Pack Qty.
1 1 1
U
L
A
P
K
C T
Four Bolt Flange Item No.
INA-210 INA-215 INA-220 INA-225 INA-235 INA-240
864
Bore 1
⁄2 5 ⁄8 3 ⁄4 7 ⁄8 1 11⁄8
A
3 3 33⁄8 33⁄4 33⁄4 49⁄32
C 13
⁄32 13 ⁄32 15 ⁄32 1 ⁄2 1 ⁄2 1 ⁄2
K 15
⁄32 15 ⁄32 15 ⁄32 15 ⁄32 15 ⁄32 15 ⁄32
L
M
13⁄32 13⁄32 17⁄32 111⁄32 111⁄32 11⁄2
21⁄8 21⁄8 21⁄2 23⁄4 23⁄4 31⁄4
P 21
⁄32 21 ⁄32 3 ⁄4 3 ⁄4 3 ⁄4 25 ⁄32
T 15
⁄16 15 ⁄16 15⁄32 13⁄16 13⁄16 11⁄4
U
Pack Qty.
Item No.
Bore
A
19⁄32 19⁄32 115⁄32 117⁄32 117⁄32 121⁄32
1 1 1 1 1 1
INA-250 INA-255 INA-260 INA-265 INA-285 INA-290
11⁄4 13⁄8 17⁄16 11⁄2 115⁄16 2
421⁄32 421⁄32 421⁄32 51⁄8 55⁄8 613⁄32
C 17
⁄32 17 ⁄32 17 ⁄32 19 ⁄32 19 ⁄32 21 ⁄32
K 9
⁄16 9 ⁄16 9 ⁄16 9 ⁄16 21 ⁄32 21 ⁄32
L
M
111⁄16 111⁄16 111⁄16 115⁄16 21⁄32 23⁄16
35⁄8 35⁄8 35⁄8 4 43⁄8 51⁄8
P 27
⁄32 27 ⁄32 27 ⁄32 15 ⁄16 13⁄32 17⁄32
T
U
Pack Qty.
13⁄8 13⁄8 13⁄8 11⁄2 121⁄32 127⁄32
127⁄32 127⁄32 127⁄32 21⁄8 23⁄8 217⁄32
1 1 1 1 1 1
MOUNTED BEARINGS Standard duty, high-grade cast iron. Solid foot housing design. Wide inner ring bearing. Relubricatable unit with anti-rotation pin. Pillow Block - Standard Shaft Height
K
L H A D E min E max B
C
Pillow Block
Item No.
PRB-107 PRB-108 PRB-109 PRB-110 PRB-140 PRB-111 PRB-112 PRB-143 PRB-113 PRB-145 PRB-114 PRB-147 PRB-115 PRB-149 PRB-116 PRB-151 PRB-117 PRB-153
Bearing No.
Bore Size
Load Rate
1
⁄2 ⁄8 ⁄4 7 ⁄8 15 ⁄16 1 11⁄8 13⁄16 11⁄4 11⁄4 13⁄8 17⁄16 11⁄2 111⁄16 13⁄4 115⁄16 2 23⁄16
UCP201-8 UCP202-10 UCP204-12 UCP205-14 UCP205-15 UCP205-16 UCP206-18 UCP206-19 UCP206-20 UCP207-20 UCP207-22 UCP207-23 UCP208-24 UCP209-27 UCP209-28 UCP210-31 UCP211-32 UCP211-35
2,900 2,900 2,900 3,150 3,150 3,150 4,390 4,390 4,390 5,740 5,740 5,740 7,340 7,470 7,470 7,900 9,810 9,810
5 3
A
B
C
3
15
17
1 ⁄16 13⁄16 15⁄16 17⁄16 17⁄16 17⁄16 111⁄16 111⁄16 111⁄16 17⁄8 17⁄8 17⁄8 115⁄16 115⁄16 21⁄8 21⁄4 21⁄2 21⁄2
5 ⁄32 515⁄32 5 51⁄2 51⁄2 51⁄2 61⁄2 61⁄2 61⁄2 69⁄16 69⁄16 69⁄16 71⁄4 715⁄32 715⁄32 81⁄8 85⁄8 85⁄8
D 15
1 ⁄64 117⁄64 111⁄32 11⁄2 11⁄2 11⁄2 13⁄4 13⁄4 13⁄4 113⁄16 113⁄16 113⁄16 159⁄64 21⁄64 21⁄64 23⁄16 25⁄16 25⁄16
⁄32 ⁄32 ⁄32 5 ⁄8 5 ⁄8 5 ⁄8 21 ⁄32 21 ⁄32 21 ⁄32 23 ⁄32 23 ⁄32 23 ⁄32 13 ⁄16 3 ⁄4 3 ⁄4 3 ⁄4 7 ⁄8 7 ⁄8 15 17
E Min.
E Max.
H
K
L
Pack Qty.
3 3 3 35⁄8 311⁄16 35⁄8 315⁄16 41⁄4 315⁄16 411⁄16 43⁄16 411⁄16 419⁄32 415⁄16 415⁄16 57⁄8 527⁄32 63⁄8
1
7
.394 .394 .5 .563 .563 .563 .625 .625 .625 3 ⁄8 3 ⁄8 3 ⁄8 .748 .748 .748 .748 .874 .874
.72 .72 .72 .776 25 ⁄32 .776 .874 7 ⁄8 .874 1 1 1 1.189 11⁄8 1.189 117⁄64 1.315 19⁄32
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
4 ⁄2 41⁄2 41⁄2 45⁄8 411⁄32 45⁄8 59⁄16 5 59⁄16 51⁄4 513⁄16 51⁄4 67⁄32 53⁄4 69⁄15 61⁄2 719⁄32 71⁄8
2 ⁄32 27⁄32 217⁄32 225⁄32 225⁄32 225⁄32 39⁄32 39⁄32 39⁄32 311⁄16 311⁄16 311⁄16 4 41⁄4 41⁄4 49⁄16 431⁄32 431⁄32
Pillow Block - Low Shaft Height
K
L H A D E min E max B
C
Pillow Block
Item No.
Bearing No.
PRB-154 PRB-155 PRB-156 PRB-157 PRB-158 PRB-159 PRB-160 PRB-161 PRB-163
UCLP201-8 UCLP202-10 UCLP204-12 UCLP205-14 UCLP205-15 UCLP205-16 UCLP206-18 UCLP206-19 UCLP207-20
Bore Size 1
⁄2 5 ⁄8 3 ⁄4 7 ⁄8 15 ⁄16 1 11⁄8 13⁄16 11⁄4
Load Rate
A
B
C
2,150 2,150 2,860 3,150 3,150 3,150 4,390 4,390 5,740
11⁄4 11⁄4 11⁄4 15⁄16 15⁄16 15⁄16 19⁄16 19⁄16 113⁄16
5 5 5 51⁄2 51⁄2 51⁄2 61⁄2 61⁄2 69⁄16
111⁄32 111⁄32 111⁄32 11⁄2 11⁄2 11⁄2 13⁄4 13⁄4 113⁄16
E Min.
E Max.
H
315⁄32 315⁄32 315⁄32 311⁄16 311⁄16 311⁄16 41⁄4 41⁄4 411⁄16
43⁄16 43⁄16 43⁄16 411⁄32 411⁄32 411⁄32 5 5 51⁄4
215⁄32 215⁄32 215⁄32 221⁄32 221⁄32 221⁄32 35⁄32 35⁄32 35⁄8
D 15
⁄32 15 ⁄32 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 17 ⁄32 17 ⁄32 21 ⁄32
K
L
1
5
⁄4 1 ⁄4 9 ⁄32 5 ⁄16 5 ⁄16 5 ⁄16 23 ⁄64 23 ⁄64 3 ⁄8
Pack Qty.
⁄8 5 ⁄8 23 ⁄32 25 ⁄32 25 ⁄32 25 ⁄32 7 ⁄8 7 ⁄8 1
1 1 1 1 1 1 1 1 1
These mounted bearings are used extensively in fabricated equipment because they are easy to fit, maintain and replace. They are sealed and pre-greased, and under normal conditions require no further lubrications (grease fitting is supplied for additional lubrication under adverse conditions.) Housing is made from cast iron. All bearings below have set screw shaft locking. Pillow Block
O
K
H A C B
M W
Pillow Block
Item No.
INA-10 INA-15 INA-20 INA-25 INA-35 INA-40
Bore 1
⁄2 5 ⁄8 3 ⁄4 7 ⁄8 1 11⁄8
A
B
13⁄16 13⁄16 15⁄16 17⁄16 17⁄16 111⁄16
11⁄4 11⁄4 11⁄4 115⁄32 115⁄32 111⁄16
C 9
⁄16 9 ⁄16 9 ⁄16 5 ⁄8 5 ⁄8 23 ⁄32
H
29⁄32 29⁄32 217⁄32 213⁄16 213⁄16 39⁄32
K 7
⁄16 7 ⁄16 7 ⁄16 15 ⁄32 15 ⁄32 19 ⁄32
M
41⁄16 41⁄16 41⁄8 41⁄2 41⁄2 5
O 5
⁄8 5 ⁄8 23 ⁄32 25 ⁄32 25 ⁄32 7 ⁄8
W
Pack Qty.
Item No.
Bore
A
B
415⁄16 415⁄16 51⁄8 51⁄2 51⁄2 63⁄16
1 1 1 1 1 1
INA-50 INA-55 INA-65 INA-80 INA-90
11⁄4 13⁄8 11⁄2 13⁄4 2
17⁄8 17⁄8 115⁄16 21⁄8 21⁄2
127⁄32 127⁄32 131⁄32 21⁄32 215⁄32
C 3
⁄4 3 ⁄4 .787 7 ⁄8 1
H
311⁄16 311⁄16 315⁄16 47⁄32 431⁄32
K 19
⁄32 19 ⁄32 19 ⁄32 9 ⁄16 23 ⁄32
M
O
W
Pack Qty.
57⁄16 57⁄16 5.787 65⁄16 73⁄8
1 1 13⁄16 13⁄16 15⁄16
625⁄32 625⁄32 75⁄32 711⁄16 87⁄8
1 1 1 1 1
865
MOUNTED BEARINGS B
E
J
Y
A
K
C
These mounted bearings are used extensively in fabricating equipment because they are easy to fit, maintain and replace. Made of cast iron housings with a grease fitting for easy lubrication. Pillow block style comes in two types, standard height and low center height.
D
Four Bolt Flange Standard Duty Set Screw Locking - Wide Inner Ring - M-Seal and Flingers Item No.
SKF-8100 SKF-8105 SKF-8110 SKF-8115 SKF-8120 SKF-8125 SKF-8130 SKF-8135 SKF-8140 SKF-8145 SKF-8150 SKF-8155 SKF-8160 SKF-8165 SKF-8170 SKF-8175 SKF-8180 SKF-8185
Bore 1
⁄2 5 ⁄8 3 ⁄4 7 ⁄8 15 ⁄16 1 11⁄8 13⁄16 11⁄4 11⁄4 13⁄8 17⁄16 11⁄2 111⁄16 115⁄16 2 23⁄16 27⁄16
Load Rating
A
B
2,150 2,150 2,860 3,150 3,150 3,150 4,390 4,390 4,390 5,740 5,740 5,740 6,910 7,470 7,900 9,810 9,810 11,900
3 3 33⁄8 33⁄4 33⁄4 33⁄4 41⁄4 41⁄4 41⁄4 45⁄8 45⁄8 45⁄8 51⁄8 53⁄8 55⁄8 63⁄8 63⁄8 67⁄8
21⁄8 21⁄8 21⁄2 23⁄4 23⁄4 23⁄4 31⁄4 31⁄4 31⁄4 35⁄8 35⁄8 35⁄8 4 41⁄8 43⁄8 51⁄8 51⁄8 55⁄8
C 13
⁄32 13 ⁄32 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 19 ⁄32 19 ⁄32 19 ⁄32 5 ⁄8 5 ⁄8 5 ⁄8 21 ⁄32 11 ⁄16 25 ⁄32 27 ⁄32 27 ⁄32 27 ⁄32
D 15
⁄16 15 ⁄16 11⁄8 13⁄16 13⁄16 13⁄16 19⁄32 19⁄32 19⁄32 13⁄8 13⁄8 13⁄8 117⁄32 119⁄32 13⁄4 17⁄8 17⁄8 25⁄32
E
J
17⁄32 17⁄32 115⁄32 117⁄32 117⁄32 117⁄32 121⁄32 121⁄32 121⁄32 113⁄16 113⁄16 113⁄16 23⁄32 23⁄32 25⁄16 215⁄32 215⁄32 227⁄32
21⁄8 21⁄8 23⁄8 23⁄4 23⁄4 23⁄4 31⁄4 31⁄4 31⁄4 35⁄8 35⁄8 35⁄8 4 41⁄4 45⁄8 5 5 51⁄2
E
J
7
1
K 19
⁄32 19 ⁄32 3 ⁄4 3 ⁄4 3 ⁄4 3 ⁄4 25 ⁄32 25 ⁄32 25 ⁄32 13 ⁄16 13 ⁄16 13 ⁄16 29 ⁄32 29 ⁄32 11⁄32 15⁄32 15⁄32 19⁄32
Y 1
Pack Qty.
⁄8 1 ⁄8 1 ⁄4 3 ⁄16 3 ⁄16 3 ⁄16 5 ⁄32 5 ⁄32 5 ⁄32 1 ⁄8 1 ⁄8 1 ⁄8 5 ⁄32 5 ⁄32 9 ⁄32 11 ⁄32 11 ⁄32 9 ⁄32
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Y
Pack Qty.
Four Bolt Flange Standard Duty Set Screw Locking - Narrow Inner Ring - M-Seal Item No.
SKF-437 SKF-438 SKF-439 SKF-440 SKF-442 SKF-444 SKF-445 SKF-446 SKF-447 SKF-448 SKF-449 SKF-450 SKF-451 SKF-452 SKF-453 SKF-454
Bore 1
⁄2 ⁄8 ⁄4 7 ⁄8 1 13⁄16 11⁄4 11⁄4 13⁄8 17⁄16 11⁄2 111⁄16 13⁄4 115⁄16 2 23⁄16 5 3
Load Rating
2,150 2,150 2,860 3,150 3,150 4,390 4,390 5,740 5,740 5,740 6,910 7,470 7,470 7,900 9,810 9,810
A
B
3 3 33⁄8 33⁄4 33⁄4 41⁄4 41⁄4 45⁄8 45⁄8 45⁄8 51⁄8 53⁄8 53⁄8 55⁄8 63⁄8 63⁄8
1
2 ⁄8 21⁄8 21⁄2 23⁄4 23⁄4 31⁄4 31⁄4 35⁄8 35⁄8 35⁄8 4 41⁄8 41⁄8 43⁄8 51⁄16 51⁄8
C 13
⁄32 ⁄32 ⁄8 5 ⁄8 5 ⁄8 19 ⁄32 19 ⁄32 5 ⁄8 5 ⁄8 5 ⁄8 21 ⁄32 11 ⁄16 11 ⁄16 25 ⁄32 27 ⁄32 27 ⁄32 13 5
D 15
⁄16 ⁄16 11⁄8 13⁄16 13⁄16 19⁄32 19⁄32 13⁄8 13⁄8 13⁄8 117⁄32 119⁄32 119⁄32 13⁄4 17⁄8 17⁄8 15
1 ⁄32 17⁄32 115⁄32 117⁄32 117⁄32 121⁄32 121⁄32 113⁄16 113⁄16 113⁄16 21⁄32 27⁄64 27⁄64 219⁄64 27⁄16 27⁄16
2 ⁄8 21⁄8 23⁄8 23⁄4 23⁄4 31⁄4 31⁄4 35⁄8 35⁄8 35⁄8 4 41⁄4 41⁄4 45⁄8 5 5
K 19
⁄32 ⁄32 ⁄4 3 ⁄4 3 ⁄4 25 ⁄32 25 ⁄32 13 ⁄16 13 ⁄16 13 ⁄16 29 ⁄32 29 ⁄32 29 ⁄32 11⁄32 15⁄32 15⁄32 19 3
21
⁄64 ⁄64 ⁄32 29 ⁄64 29 ⁄64 27 ⁄64 27 ⁄64 7 ⁄16 7 ⁄16 7 ⁄16 29 ⁄64 15 ⁄32 15 ⁄32 39 ⁄64 43 ⁄64 43 ⁄64
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Y
Pack Qty.
21 15
Four Bolt Flange Standard Duty Eccentric Locking - Narrow Inner Ring - M-Seal Item No.
SKF-8195 SKF-8200 SKF-8210 SKF-8215 SKF-8220 SKF-8225 SKF-8230 SKF-8235 SKF-8240 SKF-8245 SKF-8250 SKF-8255 SKF-8260 SKF-8265
Bore 3
⁄4 7 ⁄8 1 11⁄8 13⁄16 11⁄4 11⁄4 13⁄8 17⁄16 11⁄2 111⁄16 115⁄16 2 23⁄16
Load Rating
A
B
2,860 3,150 3,150 4,390 4,390 4,390 5,740 5,740 5,740 6,910 7,470 7,900 9,810 9,810
33⁄8 33⁄4 33⁄4 41⁄4 41⁄4 41⁄4 45⁄8 45⁄8 45⁄8 51⁄8 53⁄8 55⁄8 63⁄8 63⁄8
21⁄2 23⁄4 23⁄4 31⁄4 31⁄4 31⁄4 35⁄8 35⁄8 35⁄8 4 41⁄8 43⁄8 51⁄8 51⁄8
C 13
⁄32 5 ⁄8 5 ⁄8 19 ⁄32 19 ⁄32 19 ⁄32 5 ⁄8 5 ⁄8 5 ⁄8 21 ⁄32 11 ⁄16 25 ⁄32 27 ⁄32 27 ⁄32
D
E
J
11⁄8 13⁄16 13⁄16 19⁄32 19⁄32 19⁄32 13⁄8 13⁄8 13⁄8 117⁄32 119⁄32 13⁄4 17⁄8 17⁄8
111⁄16 111⁄16 111⁄16 127⁄32 127⁄32 127⁄32 131⁄32 131⁄32 131⁄32 23⁄16 23⁄16 25⁄16 219⁄32 219⁄32
23⁄8 23⁄4 23⁄4 31⁄4 31⁄4 31⁄4 35⁄8 35⁄8 35⁄8 4 41⁄4 45⁄8 5 5
K 3
⁄4 3 ⁄4 3 ⁄4 25 ⁄32 25 ⁄32 25 ⁄32 13 ⁄16 13 ⁄16 13 ⁄16 29 ⁄32 29 ⁄32 11⁄32 15⁄32 15⁄32
29
⁄64 15 ⁄32 15 ⁄32 7 ⁄16 7 ⁄16 7 ⁄16 7 ⁄16 7 ⁄16 7 ⁄16 15 ⁄32 15 ⁄32 19 ⁄32 11 ⁄16 11 ⁄16
1 1 1 1 1 1 1 1 1 1 1 1 1 1
Y
Pack Qty.
Four Bolt Flange Standard Duty Wide Width - ConCentra Lock Air Handling Unit Item No.
Bore
Load Rating
A
B
SKF-8300 SKF-8290 SKF-8275 SKF-8295 SKF-8270 SKF-8280 SKF-8285 SKF-8315 SKF-8320 SKF-8305 SKF-8310
1 13⁄16 11⁄4 17⁄16 11⁄2 111⁄16 115⁄16 23⁄16 27⁄16 211⁄16 215⁄16
2,150 4,390 4,390 5,740 6,910 7,470 7,900 9,810 11,900 12,900 14,800
3 41⁄4 41⁄4 441⁄64 51⁄8 525⁄64 55⁄8 63⁄8 67⁄8 73⁄8 73⁄4
21⁄8 31⁄4 35⁄8 35⁄8 4 41⁄8 43⁄8 51⁄8 55⁄8 57⁄8 6
866
C 25
⁄64 33 ⁄64 33 ⁄64 33 ⁄64 35 ⁄64 35 ⁄64 19 ⁄32 5 ⁄8 43 ⁄64 21 ⁄32 3 ⁄4
D 59
⁄64 19⁄32 19⁄32 123⁄64 133⁄64 117⁄32 111⁄16 17⁄8 23⁄64 21⁄16 21⁄8
E
J
17⁄32 121⁄32 121⁄32 156⁄64 29⁄64 29⁄64 225⁄64 235⁄64 229⁄32 255⁄64 3
21⁄8 319⁄64 319⁄64 347⁄64 411⁄64 413⁄32 441⁄64 59⁄32 55⁄8 61⁄16 63⁄8
K 37
⁄64 25 ⁄32 25 ⁄32 53 ⁄64 15 ⁄16 15 ⁄16 17⁄64 17⁄32 111⁄32 15⁄32 13⁄16
1
⁄8 5 ⁄32 5 ⁄32 9 ⁄64 13 ⁄64 13 ⁄64 23 ⁄64 11 ⁄32 11 ⁄32 5 ⁄32 1 ⁄8
1 1 1 1 1 1 1 1 1 1 1
MOUNTED BEARINGS
E
K
B
A
Y
J
C
D
These mounted bearings are used extensively in fabricating equipment because they are easy to fit, maintain and replace. Made of cast iron housings with a grease fitting for easy lubrication. Pillow block style comes in two types, standard height and low center height.
Two Bolt Flange Standard Duty Set Screw Locking - Wide Inner Ring - M-Seal and Flingers
Item No.
SKF-8325 SKF-8330 SKF-8335 SKF-8340 SKF-8345 SKF-8350 SKF-8355 SKF-8360 SKF-8365 SKF-8370 SKF-8375 SKF-8380 SKF-8385 SKF-8390 SKF-8395
Bore 1
⁄2 ⁄8 ⁄4 15 ⁄16 1 11⁄8 13⁄16 11⁄4 11⁄4 13⁄8 17⁄16 11⁄2 115⁄16 2 23⁄16 5 3
Load Rating
A
B
2,150 2,150 2,860 3,150 3,150 4,390 4,390 4,390 5,740 5,740 5,740 6,910 7,900 9,810 9,810
37⁄8 37⁄8 413⁄32 47⁄8 47⁄8 59⁄16 59⁄16 59⁄16 61⁄8 61⁄8 61⁄8 63⁄4 77⁄16 81⁄4 81⁄4
3 3 317⁄32 329⁄32 329⁄32 419⁄32 419⁄32 419⁄32 51⁄8 51⁄8 51⁄8 521⁄32 63⁄16 71⁄4 71⁄4
C 15
⁄32 ⁄32 ⁄16 5 ⁄8 5 ⁄8 17 ⁄32 17 ⁄32 17 ⁄32 9 ⁄16 9 ⁄16 9 ⁄16 9 ⁄16 25 ⁄32 13 ⁄16 13 ⁄16 15 7
D 15
⁄16 ⁄16 ⁄32 13⁄16 13⁄16 19⁄32 19⁄32 19⁄32 111⁄32 111⁄32 111⁄32 117⁄32 123⁄32 17⁄8 17⁄8 15
31
K
J
17⁄32 17⁄32 19⁄32 117⁄32 117⁄32 121⁄32 121⁄32 121⁄32 113⁄16 113⁄16 113⁄16 23⁄32 29⁄32 215⁄32 215⁄32
21⁄8 21⁄8 23⁄8 23⁄4 23⁄4 31⁄8 31⁄8 31⁄8 35⁄8 35⁄8 35⁄8 4 49⁄16 5 5
⁄32 ⁄32 ⁄16 3 ⁄4 3 ⁄4 25 ⁄32 25 ⁄32 25 ⁄32 13 ⁄16 13 ⁄16 13 ⁄16 29 ⁄32 1 15⁄32 15⁄32
⁄8 ⁄8 ⁄16 3 ⁄16 3 ⁄16 5 ⁄32 5 ⁄32 5 ⁄32 1 ⁄8 1 ⁄8 1 ⁄8 5 ⁄32 1 ⁄4 9 ⁄32 9 ⁄32
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
E
J
K
Y
Pack Qty.
17⁄32 17⁄32 19⁄32 117⁄32 117⁄32 117⁄32 121⁄32 121⁄32 113⁄16 113⁄16 113⁄16 23⁄32 23⁄32
21⁄8 21⁄8 23⁄8 23⁄4 23⁄4 23⁄4 31⁄8 31⁄8 35⁄8 35⁄8 35⁄8 4 41⁄4
E
J
7
1
19 19 9
Y
Pack Qty.
E
1 1
1
Two Bolt Flange Standard Duty Set Screw Locking - Narrow Inner Ring - M-Seal
Item No.
SKF-455 SKF-456 SKF-457 SKF-458 SKF-459 SKF-460 SKF-462 SKF-463 SKF-464 SKF-465 SKF-466 SKF-467 SKF-468
Bore 1
⁄2 ⁄8 ⁄4 7 ⁄8 15 ⁄16 1 13⁄16 11⁄4 11⁄4 13⁄8 17⁄16 11⁄2 111⁄16 5 3
Load Rating
A
B
2,150 2,150 2,860 3,150 3,150 3,150 4,390 4,390 5,740 5,740 5,740 6,910 7,470
37⁄8 37⁄8 413⁄32 47⁄8 47⁄8 47⁄8 59⁄16 59⁄16 61⁄8 61⁄8 61⁄8 63⁄4 71⁄16
3 3 317⁄32 329⁄32 329⁄32 329⁄32 419⁄32 419⁄32 51⁄8 51⁄8 51⁄8 521⁄32 527⁄32
C 15
⁄32 ⁄32 ⁄16 5 ⁄8 5 ⁄8 5 ⁄8 17 ⁄32 17 ⁄32 9 ⁄16 9 ⁄16 9 ⁄16 9 ⁄16 5 ⁄8 15 7
D 15
⁄16 ⁄16 ⁄32 13⁄16 13⁄16 13⁄16 19⁄32 19⁄32 111⁄32 111⁄32 111⁄32 117⁄32 117⁄32 15
31
19
⁄32 ⁄32 ⁄16 3 ⁄4 3 ⁄4 3 ⁄4 25 ⁄32 25 ⁄32 13 ⁄16 13 ⁄16 13 ⁄16 29 ⁄32 29 ⁄32 19 9
21
⁄64 ⁄64 ⁄32 29 ⁄64 29 ⁄64 29 ⁄64 27 ⁄64 27 ⁄64 7 ⁄16 7 ⁄16 7 ⁄16 29 ⁄64 15 ⁄32
1 1 1 1 1 1 1 1 1 1 1 1 1
Y
Pack Qty.
21 9
Two Bolt Flange Standard Duty Eccentric Locking - Narrow Inner Ring - M-Seal
Item No.
SKF-8400 SKF-8405 SKF-8410 SKF-8415 SKF-8420 SKF-8425 SKF-8430 SKF-8435 SKF-8440 SKF-8445 SKF-8450 SKF-8455 SKF-8460 SKF-8465 SKF-8470
Bore 1
⁄2 ⁄8 ⁄4 7 ⁄8 15 ⁄16 1 11⁄8 13⁄16 11⁄4 11⁄4 13⁄8 17⁄16 11⁄2 115⁄16 2 5 3
Load Rating
2,150 2,150 2,860 3,150 3,150 3,150 4,390 4,390 4,390 5,740 5,740 5,740 6,910 7,900 9,810
A 7
3 ⁄8 37⁄8 413⁄32 47⁄8 47⁄8 47⁄8 59⁄16 59⁄16 59⁄16 61⁄8 61⁄8 61⁄8 63⁄4 77⁄16 81⁄2
B
3 3 317⁄32 329⁄32 329⁄32 329⁄32 419⁄32 419⁄32 419⁄32 51⁄8 51⁄8 51⁄8 521⁄32 63⁄16 71⁄4
C 15
⁄32 ⁄32 ⁄16 5 ⁄8 5 ⁄8 5 ⁄8 17 ⁄32 17 ⁄32 17 ⁄32 9 ⁄16 9 ⁄16 9 ⁄16 9 ⁄16 25 ⁄32 13 ⁄16 15 7
D 15
⁄16 ⁄16 ⁄32 13⁄16 13⁄16 13⁄16 19⁄32 19⁄32 19⁄32 111⁄32 111⁄32 111⁄32 117⁄32 123⁄32 17⁄8 15
31
1 ⁄16 17⁄16 11⁄2 111⁄16 111⁄16 111⁄16 127⁄32 127⁄32 127⁄32 131⁄32 131⁄32 131⁄32 23⁄16 29⁄32 219⁄32
2 ⁄8 21⁄8 23⁄8 23⁄4 23⁄4 23⁄4 31⁄8 31⁄8 31⁄8 35⁄8 35⁄8 35⁄8 4 49⁄16 5
K 19
⁄32 ⁄32 ⁄16 3 ⁄4 3 ⁄4 3 ⁄4 25 ⁄32 25 ⁄32 25 ⁄32 13 ⁄16 13 ⁄16 13 ⁄16 29 ⁄32 1 15⁄32 19 9
21
⁄64 ⁄64 ⁄64 29 ⁄64 29 ⁄64 29 ⁄64 27 ⁄64 27 ⁄64 27 ⁄64 7 ⁄16 7 ⁄16 7 ⁄16 15 ⁄32 9 ⁄16 11 ⁄16 21
17
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
867
MOUNTED BEARINGS Full stainless bearing units are the most common solution for hostile chemical wash down applications. All metal bearing insert components are 302, 304, or 440 stainless steel, have silicone rubber seals, utilize H-1 food grade grease and have an operating temperature range of -10 degrees Fahrenheit to 250 degrees Fahrenheit. The solid 304 stainless housings have a fully machined base and an extremely smooth surface finish, essential for demanding wash down installations. These housings do not experience flaking, cracking, deformation or discoloration and are virtually unaffected by scrapes. 3-Bolt Flange Bracket Units All Stainless Steel B-Type Seals Set Screw Locking
Food Grade
Item No.
A
E
K
3G Drill C B
D
Tapped Base Units All Stainless Steel B-Type Seals Set Screw Locking
Item No.
Inch IP-100 IP-101 IP-102 IP-104 IP-106 IP-107 IP-109 IP-110 IP-111 IP-112 IP-113 IP-115 IP-116 IP-118 IP-119 IP-121 IP-123 Metric IP-103 IP-105 IP-108 IP-114 IP-117 IP-120 IP-122
Food Grade
A L
D
K
E B
G
C
Pillow Blocks All Stainless Steel B-Type Seals Set Screw Locking
Item No.
Food Grade
K
L
H A
G
G D E B
868
Inch IP-81 IP-82 IP-83 IP-85 IP-87 IP-88 IP-90 IP-91 IP-92 IP-93 IP-94 IP-96 IP-97 IP-99 Metric IP-84 IP-86 IP-89 IP-95 IP-98
C
Bore Diameter
A
B
C
⁄2 ⁄8 ⁄4 7 ⁄8 1 11⁄8 13⁄16 11⁄4 11⁄4 15⁄16 13⁄8 17⁄16 115⁄16 2
21⁄2 21⁄2 21⁄2 23⁄4 23⁄4 31⁄4 31⁄4 31⁄4 33⁄4 33⁄4 33⁄4 33⁄4 45⁄8 45⁄8
23⁄8 23⁄8 23⁄8 21⁄2 21⁄2 23⁄4 23⁄4 23⁄4 31⁄4 31⁄4 31⁄4 31⁄4 4 4
11⁄2 11⁄2 11⁄2 15⁄8 15⁄8 17⁄8 17⁄8 17⁄8 2 2 2 2 23⁄4 23⁄4
20 25 30 35 50
64 70 83 95 118
60 64 70 83 102
38.1 28.6 47.6 50.8 69.9
1 5 3
Bore Diameter
D 5
C
⁄2 ⁄8 ⁄4 7 ⁄8 1 11⁄8 13⁄16 11⁄4 11⁄4 15⁄16 13⁄8 17⁄16 11⁄2 111⁄16 13⁄4 115⁄16 2
15⁄16 15⁄16 15⁄16 17⁄16 17⁄16 111⁄16 111⁄16 111⁄16 17⁄8 17⁄8 17⁄8 17⁄8 115⁄16 21⁄8 21⁄8 21⁄4 21⁄4
27⁄8 27⁄8 27⁄8 3 3 4 4 4 41⁄4 41⁄4 41⁄4 41⁄4 45⁄8 5 5 51⁄2 51⁄2
11⁄2 11⁄2 11⁄2 11⁄2 11⁄2 11⁄2 11⁄2 11⁄2 17⁄8 17⁄8 17⁄8 17⁄8 17⁄8 2 2 2 2
⁄2 ⁄2 ⁄2 1 ⁄2 1 ⁄2 5 ⁄8 5 ⁄8 5 ⁄8 3 ⁄4 3 ⁄4 3 ⁄4 3 ⁄4 3 ⁄4 3 ⁄4 3 ⁄4 7 ⁄8 7 ⁄8
20 25 30 35 40 45 50
33.3 36.5 42.9 47.6 49.2 54.0 57.2
73 76 102 108 117 127 140
38 38 38 48 48 50.8 101.6
13 13 16 19 19 19 22
1 5 3
Bore Diameter
Inch 1 IP-1 ⁄2 5 IP-2 ⁄8 3 IP-3 ⁄4 7 IP-5 ⁄8 IP-7 1 IP-8 11⁄8 IP-10 13⁄16 IP-11 11⁄4 IP-12 11⁄4 IP-13 15⁄16 IP-14 13⁄8 IP-16 17⁄16 IP-17 11⁄2 IP-19 111⁄16 IP-20 13⁄4 IP-22 115⁄16 IP-24 2 IP-25 2 IP-26 23⁄16 IP-27 21⁄4 IP-28 27⁄16 Metric IP-4 20 IP-6 25 IP-9 30 IP-15 35 IP-18 40 IP-21 45 IP-23 50
123⁄64 123⁄64 123⁄64 139⁄64 139⁄64 137⁄64 137⁄64 137⁄64 153⁄64 153⁄64 153⁄64 153⁄64 25⁄32 25⁄32
8 9.5 9.5 13 13
34.3 41.0 40.2 46.4 54.6
5
B
D
1 1
D
0.5000 0.5000 0.5000 0.5630 0.5630 0.6260 0.6260 0.6260 0.6890 0.6890 0.6890 0.6890 0.7480 0.7480
1 1 1 1 1 1 1 1 1 1 1 1 1 1
9.9 9.9 9.9 13.1 13.1
12.7 14.3 15.9 17.5 19.0
1 1 1 1 1
25 25
K
L
Pack Qty.
2 2 2 2 2 2 3 3 31⁄4 31⁄4 31⁄4 31⁄4 31⁄2 33⁄4 33⁄4 4 4
⁄8-16 ⁄8-16 ⁄8-16 3 ⁄8-16 3 ⁄8-16 7 ⁄16-14 7 ⁄16-14 7 ⁄16-14 1 ⁄2-13 1 ⁄2-13 1 ⁄2-13 1 ⁄2-13 1 ⁄2-13 1 ⁄2-13 1 ⁄2-13 5 ⁄8-11 5 ⁄8-11
1.2205 1.2205 1.2205 1.3386 1.3386 1.5000 1.5000 1.5000 1.6890 1.6890 1.6890 1.6890 1.9370 1.9370 1.9370 2.0315 2.0315
.7205 .7205 .7205 .7756 .7756 .8740 .8740 .8740 1.0000 1.0000 1.0000 1.0000 1.1890 1.1890 1.1890 1.2835 1.2835
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
50.8 50.8 76.2 82.6 88.9 95.3 50.8
UNC UNC UNC UNC UNC UNC UNC
31.0 34.0 38.1 42.9 49.2 49.2 51.6
18.3 19.7 22.2 25.4 30.2 30.2 32.6
1 1 1 1 1 1 1
H
K
L
Pack Qty.
3 3 3
A
B
C
15⁄16 15⁄16 15⁄16 17⁄16 17⁄16 111⁄16 111⁄16 111⁄16 17⁄8 17⁄8 17⁄8 17⁄8 115⁄16 21⁄8 21⁄8 21⁄4 21⁄4 21⁄2 21⁄2 23⁄4 23⁄4
5 5 5 515⁄32 515⁄32 613⁄32 613⁄32 613⁄32 617⁄32 617⁄32 617⁄32 617⁄32 71⁄4 71⁄2 71⁄2 8 8 817⁄32 817⁄32 915⁄32 915⁄32
11⁄2 11⁄2 11⁄2 11⁄2 11⁄2 127⁄32 127⁄32 127⁄32 129⁄32 129⁄32 129⁄32 129⁄32 2 21⁄16 21⁄16 25⁄16 25⁄16 23⁄8 23⁄8 21⁄2 21⁄2
⁄32 ⁄32 ⁄32 5 ⁄8 5 ⁄8 11 ⁄16 11 ⁄16 11 ⁄16 3 ⁄4 3 ⁄4 3 ⁄4 3 ⁄4 25 ⁄32 25 ⁄32 25 ⁄32 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 1 1
33⁄4 33⁄4 33⁄4 41⁄8 41⁄8 43⁄4 43⁄4 43⁄4 5 5 5 5 53⁄8 53⁄4 53⁄4 61⁄4 61⁄4 67⁄8 67⁄8 711⁄32 711⁄32
⁄16 ⁄16 ⁄16 11 ⁄16 11 ⁄16 13 ⁄16 13 ⁄16 13 ⁄16 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 13 ⁄16 13 ⁄16 15 ⁄16 15 ⁄16 15 ⁄16 15 ⁄16 1 1
29⁄16 29⁄16 29⁄16 23⁄4 23⁄4 319⁄64 319⁄64 319⁄64 311⁄16 311⁄16 311⁄16 311⁄16 315⁄16 47⁄32 47⁄32 41⁄2 41⁄2 415⁄16 415⁄16 53⁄8 53⁄8
0.5000 0.5000 0.5000 0.5630 0.5630 0.6260 0.6260 0.6260 0.6890 0.6890 0.6890 0.6890 0.7480 0.7480 0.7480 0.7480 0.7480 0.8740 0.8740 1.0000 1.0000
0.7205 0.7205 0.7205 0.7756 0.7756 0.8740 0.8740 0.8740 1.0000 1.0000 1.0000 1.0000 1.1890 1.1890 1.1890 1.2835 1.2835 1.3150 1.3150 1.5630 1.5630
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
33.3 36.5 42.9 47.6 49.2 54 57.2
127 139 163 166 184 190 203
38 38 47 48 51 52 59
15 16 18 19 20 49.2 22
127 105 121 127 136 146 159
17 17 21 22 22 21 24
65 70 84 94 100 107 114
12.7 14.3 15.9 25.4 19.0 19.0 19.0
18.3 19.7 22.2 17.5 30.2 30.2 32.6
1 1 1 1 1 1 1
19 19 19
E
⁄64 ⁄64 ⁄64 25 ⁄64 25 ⁄64 25 ⁄64 25 ⁄64 25 ⁄64 34 ⁄64 34 ⁄64 34 ⁄64 34 ⁄64 33 ⁄64 33 ⁄64
25
G
E
1
Pack Qty.
G
⁄16 ⁄16 ⁄16 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2
5
A
K
E
G 11 11 11
MOUNTED BEARINGS Full stainless bearing units are the most common solution for hostile chemical wash down applications. All metal bearing insert components are 302, 304, or 440 stainless steel, have silicone rubber seals, utilize H-1 food grade grease and have an operating temperature range of -10° F to 250° F. The solid 304 stainless housings have a fully machined base and an extremely smooth surface finish, essential for demanding wash down installations. These housings do not experience flaking, cracking, deformation or discoloration and are virtually unaffected by scrapes. 2-Bolt Flange Units All Stainless Steel B-Type Seals Set Screw Locking
E
2G Drill
K
Food Grade
C
B A Item No.
Bore Diameter
Inch IP-57 IP-58 IP-59 IP-61 IP-63 IP-64 IP-66 IP-67 IP-68 IP-69 IP-70 IP-72 IP-73 IP-75 IP-76 IP-78 IP-80 Metric IP-60 IP-62 IP-65 IP-71 IP-74 IP-77 IP-79
A
B
⁄2 ⁄8 ⁄4 7 ⁄8 1 11⁄8 13⁄16 11⁄4 11⁄4 15⁄16 13⁄8 17⁄16 11⁄2 111⁄16 13⁄4 115⁄16 2
415⁄32 415⁄32 415⁄32 47⁄8 47⁄8 59⁄16 59⁄16 59⁄16 61⁄8 61⁄8 61⁄8 61⁄8 63⁄4 71⁄16 71⁄16 77⁄16 77⁄16
317⁄32 317⁄32 317⁄32 357⁄64 357⁄64 419⁄32 419⁄32 419⁄32 51⁄8 51⁄8 51⁄8 51⁄8 521⁄32 527⁄32 527⁄32 63⁄16 63⁄16
20 25 30 35 40 45 50
114 124 141 155 171 179 189
89.7 98.8 116.7 130.2 143.7 148.4 157
1 5 3
C
D
E
⁄16 ⁄16 ⁄16 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 9 ⁄16 9 ⁄16 9 ⁄16 9 ⁄16 9 ⁄16 19 ⁄32 19 ⁄32 19 ⁄32 19 ⁄32
1 1 1 11⁄16 11⁄16 17⁄32 17⁄32 17⁄32 111⁄32 111⁄32 111⁄32 111⁄32 113⁄32 11⁄2 11⁄2 19⁄16 19⁄16
15⁄16 15⁄16 15⁄16 113⁄32 113⁄32 119⁄32 119⁄32 119⁄32 13⁄4 13⁄4 13⁄4 13⁄4 2 21⁄16 21⁄16 25⁄32 25⁄32
11 13 13 14 14 15 15
25 27 31 34 36 38 40
33.3 35.7 40.5 44.5 50.8 52.4 54.8
7 7 7
4-Bolt Flange Units All Stainless Steel B-Type Seals Set Screw Locking
D
K
Pack Qty.
⁄64 ⁄64 ⁄64 15 ⁄32 15 ⁄32 15 ⁄32 15 ⁄32 15 ⁄32 33 ⁄64 33 ⁄64 33 ⁄64 33 ⁄64 33 ⁄64 19 ⁄32 19 ⁄32 19 ⁄32 19 ⁄32
0.5000 0.5000 0.5000 0.5630 0.5630 0.6260 0.6260 0.6260 0.6890 0.6890 0.6890 0.6890 0.7480 0.7480 0.7480 0.7480 0.7480
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
10 11.9 11.9 13 13 15 15
12.7 14.3 15.9 17.5 19.0 19.0 19.0
1 1 1 1 1 1 1
G 25 25 25
E
A B
4G Drill K
Food Grade
A B
C D Item No.
Inch IP-29 IP-30 IP-31 IP-33 IP-35 IP-36 IP-38 IP-39 IP-40 IP-41 IP-42 IP-44 IP-45 IP-47 IP-48 IP-50 IP-52 IP-53 IP-54 IP-55 IP-56 Metric IP-32 IP-34 IP-37 IP-43 IP-46 IP-49 IP-51
Bore Diameter
A
B
⁄2 ⁄8 ⁄4 7 ⁄8 1 11⁄8 13⁄16 11⁄4 11⁄4 15⁄16 13⁄8 17⁄16 11⁄2 111⁄16 13⁄4 115⁄16 2 2 23⁄16 21⁄4 27⁄16
33⁄8 33⁄8 33⁄8 33⁄4 33⁄4 41⁄4 41⁄4 41⁄4 419⁄32 419⁄32 419⁄32 419⁄32 51⁄8 513⁄32 513⁄32 55⁄8 55⁄8 63⁄8 63⁄8 67⁄8 67⁄8
21⁄2 21⁄2 21⁄2 23⁄4 23⁄4 31⁄4 31⁄4 31⁄4 35⁄8 35⁄8 35⁄8 35⁄8 4 41⁄8 41⁄8 43⁄8 43⁄8 51⁄8 51⁄8 55⁄8 55⁄8
20 25 30 35 40 45 50
86 95 108 117 130 137 143
64 70 83 92 102 105 111
1 5 3
C
D
E
⁄16 ⁄16 ⁄16 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 19 ⁄32 19 ⁄32 19 ⁄32 19 ⁄32 19 ⁄32 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 23 ⁄32 23 ⁄32 23 ⁄32 23 ⁄32
1 1 1 11⁄16 11⁄16 17⁄32 17⁄32 17⁄32 111⁄32 111⁄32 111⁄32 111⁄32 113⁄32 11⁄2 11⁄2 19⁄16 19⁄16 111⁄16 111⁄16 17⁄8 17⁄8
15⁄16 15⁄16 15⁄16 113⁄32 113⁄32 119⁄32 119⁄32 119⁄32 13⁄4 13⁄4 13⁄4 13⁄4 21⁄32 21⁄16 21⁄16 25⁄32 25⁄32 25⁄16 25⁄16 223⁄32 223⁄32
11 13 13 15 15 16 16
25.4 27 31 34 36 38 40
33.3 35.7 40.2 44.4 51.2 52.2 54.6
7 7 7
K
Pack Qty.
⁄16 ⁄16 ⁄16 29 ⁄64 29 ⁄64 33 ⁄64 33 ⁄64 33 ⁄64 33 ⁄64 33 ⁄64 33 ⁄64 33 ⁄64 35 ⁄64 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 43 ⁄64 43 ⁄64 43 ⁄64 43 ⁄64
0.5 0.5 0.5 0.5630 0.5630 0.6260 0.6260 0.6260 0.6890 0.6890 0.6890 0.6890 0.7480 0.7480 0.7480 0.7480 0.7480 0.8740 0.8740 1.0000 1.0000
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
11 11.5 13 13 14 16 16
12.7 14.3 15.9 17.5 19.0 19.0 19.0
1 1 1 1 1 1 1
G 7 7 7
869
MOUNTED BEARINGS Thermoplastic housed units offer a more favorable economic choice. Available with either stainless inserts, for a higher level of corrosion resistance, or hard chrome coated inserts, where intermediate level corrosion resistance, balanced with further savings, is desired. Thermoplastic housings are off-white in color and are made from glass reinforced PBT resin. These units offer favorable chemical resistance, are very resistant to moisture absorption and have excellent mechanical, thermal and electrical properties. Operating ranges for thermoplastic housed units are from -10 degrees Fahrenheit to 210 degrees Fahrenheit. All thermoplastic housings are made with extremely smooth surfaces, have solid bases and all sleeves, bushings and grease fittings are made from 300 series stainless steel. Pillow Blocks Thermoplastic B-Type Seals Set Screw Locking
Item No.
H G
G
A D
E B
Food Grade
L
K
C
3-Bolt Flange Bracket Units Thermoplastic B-Type Seal Set Screw Locking
A
B
C
D
Stainless Steel Bearing Inserts - Inch 1 IP-124 ⁄2 15⁄16 5 11⁄2 5 IP-125 ⁄8 15⁄16 5 11⁄2 3 IP-126 ⁄4 15⁄16 5 11⁄2 7 7 1 IP-128 ⁄8 1 ⁄16 5 ⁄2 11⁄2 IP-130 51⁄2 11⁄2 1 17⁄16 1 11 13 IP-131 1 ⁄16 6 ⁄32 113⁄16 1 ⁄8 IP-133 111⁄16 613⁄32 113⁄16 13⁄16 IP-134 111⁄16 613⁄32 113⁄16 11⁄4 IP-135 17⁄8 65⁄8 129⁄32 11⁄4 5 7 5 IP-136 1 ⁄8 6 ⁄8 129⁄32 1 ⁄16 IP-137 17⁄8 65⁄8 129⁄32 13⁄8 7 7 5 IP-139 1 ⁄8 6 ⁄8 129⁄32 1 ⁄16 IP-140 115⁄16 71⁄4 21⁄8 11⁄2 Hard Chrome Coated Bearing Inserts - Inch 3 5 IP-212 ⁄4 1 ⁄16 5 11⁄2 7 IP-214 ⁄8 17⁄16 51⁄2 11⁄2 7 1 IP-216 5 ⁄2 11⁄2 1 1 ⁄16 IP-217 111⁄16 613⁄32 113⁄16 11⁄8 3 11 13 IP-219 1 ⁄16 6 ⁄32 113⁄16 1 ⁄16 IP-220 111⁄16 613⁄32 113⁄16 11⁄4 1 7 5 IP-221 1 ⁄8 6 ⁄8 129⁄32 1 ⁄4 IP-222 17⁄8 65⁄8 129⁄32 13⁄8 7 7 5 IP-224 1 ⁄8 6 ⁄8 129⁄32 1 ⁄16 IP-225 115⁄16 71⁄4 21⁄8 11⁄2 Stainless Steel Bearing Inserts - Metric IP-127 20 33.3 127 38 IP-129 25 36.5 140 38 IP-132 30 42.9 163 46 IP-138 35 47.6 168 48 IP-141 40 49.2 184 54 Hard Chrome Coated Bearing Inserts - Metric IP-213 20 33.3 127 38 IP-215 25 36.5 140 38 IP-218 30 42.9 163 46 IP-223 35 47.6 168 48 IP-226 40 49.2 184 54
9
E
G 9
H
K
L
Pack Qty.
⁄16 ⁄16 ⁄16 9 ⁄16 9 ⁄16 11 ⁄16 11 ⁄16 11 ⁄16 11 ⁄16 11 ⁄16 11 ⁄16 11 ⁄16 25 ⁄32
33⁄4 33⁄4 33⁄4 41⁄8 41⁄8 411⁄16 411⁄16 411⁄16 5 5 5 5 57⁄16
⁄16 ⁄16 ⁄16 9 ⁄16 9 ⁄16 23 ⁄32 23 ⁄32 23 ⁄32 23 ⁄32 23 ⁄32 23 ⁄32 23 ⁄32 23 ⁄32
219⁄32 219⁄32 219⁄32 213⁄16 213⁄16 319⁄64 319⁄64 319⁄64 311⁄16 311⁄16 311⁄16 311⁄16 329⁄32
0.5000 0.5000 0.5000 0.5630 0.5630 0.626 0.626 0.626 0.6890 0.6890 0.6890 0.6890 0.7480
0.7205 0.7205 0.7205 0.7756 0.7756 0.8740 0.8740 0.8740 1.0000 1.0000 1.0000 1.0000 1.1890
1 1 1 1 1 1 1 1 1 1 1 1 1
9
⁄16 ⁄16 ⁄16 11 ⁄16 11 ⁄16 11 ⁄16 11 ⁄16 11 ⁄16 11 ⁄16 25 ⁄32
33⁄4 41⁄8 41⁄8 411⁄16 411⁄16 411⁄16 5 5 5 57⁄16
9
⁄16 ⁄16 ⁄16 23 ⁄32 23 ⁄32 23 ⁄32 23 ⁄32 23 ⁄32 23 ⁄32 23 ⁄32
219⁄32 213⁄16 213⁄16 319⁄64 319⁄64 319⁄64 311⁄16 311⁄16 311⁄16 329⁄32
0.5000 0.5630 0.5630 0.626 0.626 0.626 0.6890 0.6890 0.6890 0.7480
0.7205 0.7756 0.7756 0.8740 0.8740 0.8740 1.0000 1.0000 1.0000 1.1890
1 1 1 1 1 1 1 1 1 1
14 14 18 18 20
95 105 119 127 137
14 14 18 18 18
14 71 84 94 99
12.7 14.3 15.9 17.5 19.0
18.3 19.7 22.2 25.4 30.2
1 1 1 1 1
14 14 18 18 20
95 105 119 127 137
14 14 18 18 18
14 71 84 94 99
12.7 14.3 15.9 17.5 19.0
18.3 19.7 22.2 25.4 30.2
1 1 1 1 1
9 9
9 9
9 9
9 9
Food Grade Item No.
A
E I
K 3-G Drill C B
D
870
Bore Diameter
Bore Diameter
A
B
C
Stainless Steel Bearing Inserts - Inch 1 IP-196 ⁄2 21⁄2 27⁄16 11⁄2 5 IP-197 ⁄8 21⁄2 27⁄16 11⁄2 3 1 7 IP-198 ⁄4 2 ⁄2 2 ⁄16 11⁄2 7 IP-200 ⁄8 23⁄4 21⁄2 15⁄8 3 1 IP-202 2 ⁄2 15⁄8 1 2 ⁄4 IP-203 31⁄4 3 17⁄8 11⁄8 3 1 IP-205 3 ⁄4 3 17⁄8 1 ⁄16 IP-206 31⁄4 3 17⁄8 11⁄4 1 3 1 IP-207 3 ⁄4 3 ⁄2 2 1 ⁄4 IP-208 33⁄4 31⁄2 2 15⁄16 IP-209 33⁄4 31⁄2 2 13⁄8 IP-211 33⁄4 31⁄2 2 17⁄16 Hard Chrome Coated Bearing Inserts - Inch 3 1 7 IP-272 ⁄4 2 ⁄2 2 ⁄16 11⁄2 7 IP-274 ⁄8 23⁄4 21⁄2 15⁄8 3 1 IP-276 2 ⁄2 15⁄8 1 2 ⁄4 IP-277 31⁄4 3 17⁄8 11⁄8 3 1 IP-279 3 ⁄4 3 17⁄8 1 ⁄16 IP-280 31⁄4 3 17⁄8 11⁄4 1 3 1 IP-281 3 ⁄4 3 ⁄2 2 1 ⁄4 IP-282 33⁄4 31⁄2 2 13⁄8 IP-284 33⁄4 31⁄2 2 17⁄16 Stainless Steel Bearing Inserts - Metric IP-199 20 64 62 38.1 IP-201 25 70 64 41.3 IP-204 30 83 76 47.6 IP-210 35 95 89 50.8 Hard Chrome Coated Bearing Inserts - Metric IP-273 20 64 62 38.1 IP-275 25 70 64 41.3 IP-278 30 83 76 47.6 IP-283 35 95 89 50.8
D 7
E
G
K
Pack Qty.
⁄16 ⁄16 ⁄16 7 ⁄16 7 ⁄16 17 ⁄32 17 ⁄32 17 ⁄32 41 ⁄64 41 ⁄64 41 ⁄64 41 ⁄64
15⁄16 15⁄16 15⁄16 115⁄32 115⁄32 119⁄32 119⁄32 119⁄32 149⁄64 149⁄64 149⁄64 149⁄64
25
⁄64 ⁄64 ⁄64 25 ⁄64 25 ⁄64 25 ⁄64 25 ⁄64 25 ⁄64 33 ⁄64 33 ⁄64 33 ⁄64 33 ⁄64
0.5000 0.5000 0.5000 0.5630 0.5630 0.6260 0.6260 0.6260 0.6890 0.6890 0.6890 0.6890
1 1 1 1 1 1 1 1 1 1 1 1
7
⁄16 ⁄16 ⁄16 17 ⁄32 17 ⁄32 17 ⁄32 41 ⁄64 41 ⁄64 41 ⁄64
15⁄16 115⁄32 115⁄32 119⁄32 119⁄32 119⁄32 149⁄64 149⁄64 149⁄64
25
⁄64 ⁄64 ⁄64 25 ⁄64 25 ⁄64 25 ⁄64 33 ⁄64 33 ⁄64 33 ⁄64
0.5000 0.5630 0.5630 0.6260 0.6260 0.6260 0.6890 0.6890 0.6890
1 1 1 1 1 1 1 1 1
11 11 13 16
33.3 37.1 40.6 45.0
9.9 9.9 9.9 13.1
12.7 14.3 15.9 17.5
1 1 1 1
11 11 13 16
33.3 37.1 40.6 45.0
9.9 9.9 9.9 13.1
12.7 14.3 15.9 17.5
1 1 1 1
7 7
7 7
25 25
25 25
MOUNTED BEARINGS Thermoplastic housed units offer a more favorable economic choice. Available with either stainless inserts, for a higher level of corrosion resistance, or hard chrome coated inserts, where intermediate level corrosion resistance, balanced with further savings, is desired. Thermoplastic housings are off-white in color and are made from glass reinforced PBT resin. These units offer favorable chemical resistance, are very resistant to moisture absorption and have excellent mechanical, thermal and electrical properties. Operating ranges for thermoplastic housed units are from -10 degrees Fahrenheit to 210 degrees Fahrenheit. All thermoplastic housings are made with extremely smooth surfaces, have solid bases and all sleeves, bushings and grease fittings are made from 300 series stainless steel. 4-Bolt Flanges Thermoplastic B-Type Seals Set Screw Locking
Food Grade Item No.
A B
4G Drill
E
AB
K
C D
Bore Diameter
A
B
C
Stainless Steel Bearing Inserts - Inch 17 1 IP-142 ⁄2 33⁄8 21⁄2 ⁄32 17 5 IP-143 ⁄8 33⁄8 21⁄2 ⁄32 17 3 IP-144 ⁄4 33⁄8 21⁄2 ⁄32 9 7 IP-146 ⁄8 33⁄4 23⁄4 ⁄16 9 IP-148 23⁄4 ⁄16 1 33⁄4 9 IP-149 41⁄4 31⁄4 ⁄16 11⁄8 9 IP-151 41⁄4 31⁄4 ⁄16 13⁄16 9 1 1 1 IP-152 4 ⁄4 3 ⁄4 ⁄16 1 ⁄4 5 IP-153 421⁄32 35⁄8 ⁄8 11⁄4 5 IP-154 421⁄32 35⁄8 ⁄8 15⁄16 5 IP-155 421⁄32 35⁄8 ⁄8 13⁄8 5 IP-157 421⁄32 35⁄8 ⁄8 17⁄16 21 IP-158 51⁄8 4 ⁄32 11⁄2 Hard Chrome Coated Bearing Inserts - Inch 17 3 3 1 IP-227 ⁄4 3 ⁄8 2 ⁄2 ⁄32 9 7 IP-229 ⁄8 33⁄4 23⁄4 ⁄16 9 IP-231 23⁄4 ⁄16 1 33⁄4 9 IP-232 41⁄4 31⁄4 ⁄16 11⁄8 9 IP-234 41⁄4 31⁄4 ⁄16 13⁄16 9 IP-235 41⁄4 31⁄4 ⁄16 11⁄4 5 IP-236 421⁄32 35⁄8 ⁄8 11⁄4 5 IP-237 421⁄32 35⁄8 ⁄8 13⁄8 5 IP-239 421⁄32 35⁄8 ⁄8 17⁄16 21 IP-240 51⁄8 4 ⁄32 11⁄2 Stainless Steel Bearing Inserts - Metric IP-145 20 86 64 13 IP-147 25 95 70 14 IP-150 30 108 83 14 IP-156 35 118 92 16 IP-159 40 130 102 17 Hard Chrome Coated Bearing Inserts - Metric IP-228 20 86 64 13 IP-230 25 95 70 14 IP-233 30 108 83 14 IP-238 35 118 92 16 IP-241 40 130 102 17
K
Pack Qty.
⁄16 ⁄16 ⁄16 7 ⁄16 7 ⁄16 7 ⁄16 7 ⁄16 7 ⁄16 33 ⁄64 33 ⁄64 33 ⁄64 33 ⁄64 35 ⁄64
.5000 .5000 .5000 .5630 .5630 .6260 .6260 .6260 .6890 .6890 .6890 .6890 .7480
1 1 1 1 1 1 1 1 1 1 1 1 1
7
⁄16 ⁄16 ⁄16 7 ⁄16 7 ⁄16 7 ⁄16 33 ⁄64 33 ⁄64 33 ⁄64 35 ⁄64
.5000 .5630 .5630 .6260 .6260 .6260 .6890 .6890 .6890 .7480
1 1 1 1 1 1 1 1 1 1
36.5 36.5 41.3 46.8 53.2
11 11 11 13 14
12.7 14.3 15.9 17.5 19.0
1 1 1 1 1
28 28 32 35 37
36.5 36.5 41.3 46.8 53.2
11 11 11 13 14
12.7 14.3 15.9 17.5 19.0
1 1 1 1 1
D
E
G
K
Pack Qty.
11⁄32 11⁄32 11⁄32 15⁄32 15⁄32 17⁄32 17⁄32 17⁄32 19⁄32 19⁄32 19⁄32 19⁄32 115⁄32
121⁄64 121⁄64 121⁄64 17⁄16 17⁄16 139⁄64 139⁄64 139⁄64 123⁄32 123⁄32 123⁄32 123⁄32 23⁄64
⁄16 ⁄16 ⁄16 7 ⁄16 7 ⁄16 7 ⁄16 7 ⁄16 7 ⁄16 33 ⁄64 33 ⁄64 33 ⁄64 33 ⁄64 35 ⁄64
.5000 .5000 .5000 .5630 .5630 .6260 .6260 .6260 .6890 .6890 .6890 .6890 .7480
1 1 1 1 1 1 1 1 1 1 1 1 1
11⁄32 15⁄32 15⁄32 17⁄32 17⁄32 17⁄32 19⁄32 19⁄32 19⁄32 115⁄32
121⁄64 17⁄16 17⁄16 139⁄64 139⁄64 139⁄64 123⁄32 123⁄32 123⁄32 23⁄64
7
⁄16 ⁄16 ⁄16 7 ⁄16 7 ⁄16 7 ⁄16 33 ⁄64 33 ⁄64 33 ⁄64 35 ⁄64
.5000 .5630 .5630 .6260 .6260 .6260 .6890 .6890 .6890 .7480
1 1 1 1 1 1 1 1 1 1
26 29 31 33 37
33.7 36.5 40.9 43.7 52.0
11 11 11 13 14
12.7 14.3 15.9 17.5 19.0
1 1 1 1 1
26 29 31 33 37
33.7 36.5 40.9 43.7 52.0
11 11 11 13 14
12.7 14.3 15.9 17.5 19.0
1 1 1 1 1
D
E
13⁄32 13⁄32 13⁄32 13⁄32 13⁄32 11⁄4 11⁄4 11⁄4 13⁄8 13⁄8 13⁄8 13⁄8 115⁄32
17⁄16 17⁄16 17⁄16 17⁄16 17⁄16 15⁄8 15⁄8 15⁄8 127⁄32 127⁄32 127⁄32 127⁄32 23⁄32
13⁄32 13⁄32 13⁄32 11⁄4 11⁄4 11⁄4 13⁄8 13⁄8 13⁄8 115⁄32
17⁄16 17⁄16 17⁄16 15⁄8 15⁄8 15⁄8 127⁄32 127⁄32 127⁄32 23⁄32
28 28 32 35 37
G 7 7 7
7
7
2-Bolt Flange Thermoplastic B-Type Seal Set Screw Locking
Item No.
A B 2G Drill
45
E
Food Grade
K
C D
Bore Diameter
A
B
C
Stainless Steel Bearing Inserts - Inch 7 1 IP-160 ⁄2 47⁄16 317⁄32 ⁄16 7 5 IP-161 ⁄8 47⁄16 317⁄32 ⁄16 7 3 7 17 IP-162 ⁄4 4 ⁄16 3 ⁄32 ⁄16 17 7 IP-164 ⁄8 51⁄8 357⁄64 ⁄32 17 IP-166 357⁄64 ⁄32 1 51⁄8 17 IP-167 513⁄16 419⁄32 ⁄32 11⁄8 17 IP-169 513⁄16 419⁄32 ⁄32 13⁄16 17 IP-170 513⁄16 419⁄32 ⁄32 11⁄4 5 IP-171 615⁄32 51⁄8 ⁄8 11⁄4 5 IP-172 615⁄32 51⁄8 ⁄8 15⁄16 5 IP-173 615⁄32 51⁄8 ⁄8 13⁄8 5 IP-175 615⁄32 51⁄8 ⁄8 17⁄16 25 IP-176 67⁄8 521⁄32 ⁄32 11⁄2 Hard Chrome Coated Bearing Inserts - Inch 7 3 IP-242 ⁄4 47⁄16 317⁄32 ⁄16 17 7 IP-244 ⁄8 51⁄8 357⁄64 ⁄32 17 IP-246 357⁄64 ⁄32 1 51⁄8 17 1 13 19 IP-247 5 ⁄16 4 ⁄32 ⁄32 1 ⁄8 17 IP-249 513⁄16 419⁄32 ⁄32 13⁄16 17 IP-250 513⁄16 419⁄32 ⁄32 11⁄4 5 IP-251 615⁄32 51⁄8 ⁄8 11⁄4 5 IP-252 615⁄32 51⁄8 ⁄8 13⁄8 5 IP-254 615⁄32 51⁄8 ⁄8 17⁄16 25 IP-255 67⁄8 521⁄32 ⁄32 11⁄2 Stainless Steel Bearing Inserts - Metric IP-163 20 113 89.7 11 IP-165 25 130 98.8 13 IP-168 30 148 116.7 13 IP-174 35 164 130.2 16 IP-177 40 175 143.7 20 Hard Chrome Coated Bearing Inserts - Metric IP-243 20 113 89.7 11 IP-245 25 130 98.8 13 IP-248 30 148 116.7 13 IP-253 35 164 130.2 16 IP-256 40 175 143.7 20
7 7 7
7
7
871
MOUNTED BEARINGS These bearings are self-aligning, maintenance free and made of high performance polymer. Dust, dirt, corrosion and chemical resistant. Vibration dampening capacity. Compensate for misalignment and edge loads. Lightweight and easy to install. Self-lubricating oil-free operation. Operates in temperatures from -40 degrees Fahrenheit to +275 degrees Fahrenheit. Dimensions are in millimeters. Flange Bearings A C
G
B
F
D E Shaft
Angle of Pivot
Item No.
Max.
Min.
Maximum
Recommended
A
B
C
D
E
F
G
Max. Static Load
Max. Torque Lbs.
Pack Qty.
I-703 I-704 I-705 I-706 I-707 I-708 I-709
8.00 10.00 12.00 16.00 20.00 25.00 30.00
7.964 9.964 11.957 15.957 19.948 24.948 29.948
24 24 21 24 17 14 12
10 8 7 10 7 6 5
44.2 52 56.7 72.6 89 101 118
22.3 26 31 38 47 58.5 65
31 36 41 53 65 75 87.5
8 10 12 16 20 25 30
18.0 22.0 25.0 32.0 40.0 48.5 55.0
10.5 12.0 13.0 17.5 20.0 25.0 26.0
4.3 x 6.5 5.3 x 8.0 5.3 x 8.0 6.4 x 10.0 8.4 x 12.5 8.4 x 12.5 10.5 x 16.0
247 286 337 562 675 900 1,350
2.21 3.31 4.42 6.63 12.53 14.75 16.22
1 1 1 1 1 1 1
Spherical Pillow Blocks B C
A
L
D E
G J F H
Item No.
A
B
C
D
E
F
G
H
J
L
Pack Qty.
I-591 I-592 I-594 I-595 I-597
5 6 10 12 16
8 9 14 16 21
6 7 10.5 12 15
11.1 12.7 19.0 22.2 28.5
7 10 14 14 18
25 33 35 35 60
4.5 4.5 5.5 5.5 6.5
36 44 60 60 80
3 4 6 6 6
14 20 28 28 36
1 1 1 1 1
Thermoplastic housed units offer a more favorable economic choice. Available with either stainless inserts, for a higher level of corrosion resistance, or hard chrome coated inserts, where intermediate level corrosion resistance, balanced with further savings, is desired. Thermoplastic housings are off-white in color and are made from glass reinforced PBT resin. These units offer favorable chemical resistance, are very resistant to moisture absorption and have excellent mechanical, thermal and electrical properties. Operating ranges for thermoplastic housed units are from -10 degrees Fahrenheit to 210 degrees Fahrenheit. All thermoplastic housings are made with extremely smooth surfaces, have solid bases and all sleeves, bushings and grease fittings are made from 300 series stainless steel. Tapped Base Pillow Blocks Thermoplastic B-Type Seal Set Screw Locking
Item No.
H A D E B
G
L
Food Grade C
872
Bore Diameter
A
B
C
Stainless Steel Bearing Inserts - Inch 1 IP-178 ⁄2 15⁄16 27⁄8 13⁄8 5 IP-179 ⁄8 15⁄16 27⁄8 13⁄8 3 5 7 IP-180 ⁄4 1 ⁄16 2 ⁄8 13⁄8 7 IP-182 ⁄8 17⁄16 3 19⁄16 7 IP-184 3 19⁄16 1 1 ⁄16 IP-185 111⁄16 4 111⁄16 11⁄8 3 11 IP-187 1 ⁄16 4 111⁄16 1 ⁄16 IP-188 111⁄16 4 111⁄16 11⁄4 1 7 5 IP-189 1 ⁄8 4 ⁄16 17⁄8 1 ⁄4 IP-190 17⁄8 45⁄16 17⁄8 15⁄16 3 7 5 IP-191 1 ⁄8 4 ⁄16 17⁄8 1 ⁄8 IP-193 17⁄8 45⁄16 17⁄8 17⁄16 1 15 3 IP-194 1 ⁄16 4 ⁄4 17⁄8 1 ⁄2 Hard Chrome Coated Bearing Inserts - Inch 3 IP-257 ⁄4 15⁄16 27⁄8 13⁄8 7 IP-259 ⁄8 17⁄16 3 19⁄16 IP-261 3 19⁄16 1 17⁄16 IP-262 111⁄16 4 111⁄16 11⁄8 IP-264 111⁄16 4 111⁄16 13⁄16 1 11 IP-265 1 ⁄16 4 111⁄16 1 ⁄4 IP-266 17⁄8 45⁄16 17⁄8 11⁄4 3 7 5 IP-267 1 ⁄8 4 ⁄16 17⁄8 1 ⁄8 IP-269 17⁄8 45⁄16 17⁄8 17⁄16 1 15 3 IP-270 1 ⁄16 4 ⁄4 17⁄8 1 ⁄2 Stainless Steel Bearing Inserts - Metric IP-181 20 33.3 73 35 IP-183 25 36.5 76 40 IP-186 30 42.9 102 43 IP-192 35 47.6 110 48 IP-195 40 49.2 120 48 Hard Chrome Coated Bearing Inserts - Metric IP-258 20 33.3 73 35 IP-260 25 36.5 76 40 IP-263 30 42.9 102 43 47.6 110 48 IP-268 35 IP-271 40 49.2 120 48
E
G
H
L
Pack Qty.
2 2 2 2 2 3 3 3 31⁄4 31⁄4 31⁄4 31⁄4 31⁄2
⁄8-16 ⁄8-16 ⁄8-16 3 ⁄8-16 3 ⁄8-16 7 ⁄16-14 7 ⁄16-14 7 ⁄16-14 1 ⁄2-13 1 ⁄2-13 1 ⁄2-13 1 ⁄2-13 1 ⁄2-13
219⁄32 219⁄32 219⁄32 229⁄32 229⁄32 35⁄16 35⁄16 35⁄16 33⁄4 33⁄4 33⁄4 33⁄4 4
.7205 .7205 .7205 .7756 .7756 .8740 .8740 .8740 1.0000 1.0000 1.0000 1.0000 1.1890
1 1 1 1 1 1 1 1 1 1 1 1 1
⁄2 ⁄2 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 41 ⁄64 41 ⁄64 41 ⁄64 41 ⁄64
2 2 2 3 3 3 31⁄4 31⁄4 31⁄4 31⁄2
3
⁄8-16 ⁄8-16 ⁄8-16 7 ⁄16-14 7 ⁄16-14 7 ⁄16-14 1 ⁄2-13 1 ⁄2-13 1 ⁄2-13 1 ⁄2-13
219⁄32 229⁄32 229⁄32 35⁄16 35⁄16 35⁄16 33⁄4 33⁄4 33⁄4 4
.7205 .7756 .7756 .8740 .8740 .8740 1.0000 1.0000 1.0000 1.1890
1 1 1 1 1 1 1 1 1 1
13 13 13 16 16
50.8 50.8 76.2 82.6 88.9
— — — — —
66 74 84 95 101
18.3 19.7 22.2 25.4 30.2
1 1 1 1 1
13 13 13 16 16
50.8 50.8 76.2 82.6 88.9
— — — — —
66 74 84 95 101
18.3 19.7 22.2 25.4 30.2
1 1 1 1 1
D 1
⁄2 ⁄2 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 41 ⁄64 41 ⁄64 41 ⁄64 41 ⁄64 41 ⁄64 1 1
1
1 1
3 3
3
3 3
NEEDLE ROLLER BEARINGS Shell Type Shell type needle roller bearings are lightweight with the lowest sectional height among needle roller bearings with outer ring, because they employ a shell type outer ring made from a thin special-steel plate which is accurately drawn, carburized and quenched. Series BHA Inch
Series BHA are inch heavy duty series of shell type needle roller bearings with caged rollers. Bearing
Inner Ring
Item No.
Item No.
IKO-BHA57ZOH IKO-BHA68ZOH IKO-BHA78ZOH IKO-BHA87ZOH IKO-BHA98ZOH IKO-BHA108ZOH IKO-BHA1212ZOH IKO-BHA1410ZOH IKO-BHA168ZOH IKO-BHA1812ZOH IKO-BHA2824ZOH
Bearing
Inner Ring Basic Load Rating (Lbs.)
Inside Diameter 5
— — — — IKO-IRB68 IKO-IRB681 IKO-IRB8121 — IKO-IRB128 IKO-IRB1412 IKO-IRB2424
⁄ ⁄ ⁄16 1 ⁄2 9 ⁄16 5 ⁄8 3 ⁄4 7 ⁄8 1 11⁄8 13⁄4 16 3 8
7
Outside Diameter 9
⁄ ⁄ ⁄16 3 ⁄4 13 ⁄16 7 ⁄8 11⁄16 13⁄16 15⁄16 11⁄2 21⁄4 16 5 8
11
Width 7
⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ 1⁄
16 1 2 1 2 7 16 1 2 1 2 3 4 5 8 1 2 3 4 1 2
Dynamic
Static
Pack Qty.
4,150 4,880 5,680 5,670 6,380 6,680 16,600 14,300 10,200 22,500 72,200
3,730 4,740 5,970 6,120 7,330 8,020 22,600 19,500 13,100 32,200 135,000
1 1 1 1 1 1 1 1 1 1 1
Series BA Inch
Series BA are inch standard series of shell type needle roller bearings with caged rollers. Bearing
Inner Ring
Item No.
Item No.
IKO-BA44ZOH IKO-BA55ZOH IKO-BA65ZOH IKO-BA76ZOH IKO-BA85ZOH IKO-BA95ZOH IKO-BA108ZOH IKO-BA116ZOH IKO-BA126ZOH IKO-BA136ZOH IKO-BA146ZOH IKO-BA158ZOH IKO-BA166ZOH IKO-BA1710ZOH IKO-BA186ZOH IKO-BA1910ZOH IKO-BA218ZOH IKO-BA228ZOH IKO-BA248ZOH IKO-BA268ZOH IKO-BA2812ZOH IKO-BA308ZOH IKO-BA328ZOH IKO-BA348ZOH IKO-BA3612ZOH IKO-BA4216ZOH IKO-BA4410ZOH
— — — — — — IKO-IRB681 IKO-IRB86 — — — — — — — — IKO-IRB1681 IKO-IRB188 — — — IKO-IRB2481 — — — IKO-IRB3616 —
Bearing
Inner Ring Basic Load Rating (Lbs.)
Inside Diameter 1
⁄4 ⁄ ⁄ ⁄16 1 ⁄2 9 ⁄16 5 ⁄8 11 ⁄16 3 ⁄4 13 ⁄16 7 ⁄8 15 ⁄16 1 11⁄16 11⁄8 13⁄16 15⁄16 13⁄8 11⁄2 15⁄8 13⁄4 17⁄8 2 21⁄8 21⁄4 25⁄8 23⁄4 5
16 3 8
7
Outside Diameter
Width
7
16 1 2
1 5
9
5
⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ 1 11⁄16 11⁄8 13⁄16 11⁄4 15⁄16 13⁄8 11⁄2 15⁄8 15⁄8 17⁄8 2 21⁄8 21⁄4 23⁄8 21⁄2 25⁄8 3 31⁄8 16 5 8 11 16 3 4 13 16 7 8
⁄4 ⁄16 ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ 1 5 ⁄8
16 3 8 5 16 5 16 1 2 3 8 3 8 3 8 3 8 1 2 3 8 5 8 3 8 5 8 1 2 1 2 1 2 1 2 3 4 1 2 1 2 1 2 3 4
Dynamic
Static
Pack Qty.
1,770 1,880 2,220 3,290 2,490 2,760 5,420 4,530 5,040 5,230 5,430 8,000 6,010 11,600 6,330 15,000 11,100 9,770 12,900 13,700 25,200 14,700 15,400 16,100 28,500 42,000 25,000
1,390 1,560 2,010 3,470 2,510 2,970 7,310 5,980 5,850 6,300 6,740 11,400 8,020 19,200 8,910 22,500 15,800 16,600 17,900 19,800 44,500 22,800 24,700 26,600 56,700 97,900 50,800
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Series TLA Metric
Series TLA are metric standard series of shell type needle roller bearings with caged rollers.
Bearing
Inner Ring
Bearing
Inner Ring
Basic Load Rating (Lbs.)
Item No.
Item No.
Inside Diameter mm
Outside Diameter mm
Width mm
Dynamic
Static
Pack Qty.
IKO-TLA910Z IKO-TLA1010Z IKO-TLA1210Z IKO-TLA1312Z IKO-TLA1412Z IKO-TLA1512Z IKO-TLA1612Z IKO-TLA1712Z IKO-TLA1812Z IKO-TLA2012Z IKO-TLA2212Z IKO-TLA2512Z IKO-TLA2816Z IKO-TLA3012Z IKO-TLA3512Z IKO-TLA4012Z IKO-TLA4516Z IKO-TLA5020Z IKO-TLA5520Z
— IKO-IRT710 IKO-IRT810 IKO-IRT1012 IKO-IRT10122 IKO-IRT1212 IKO-IRT12121 — IKO-IRT1512 — — — — — IKO-IRT3012 — — IKO-IRT4520 IKO-IRT50201
9 10 12 13 14 15 16 17 18 20 22 25 28 30 35 40 45 50 55
13 14 16 19 20 21 22 23 24 26 28 32 35 37 42 47 52 58 63
10 10 10 12 12 12 12 12 12 12 12 12 16 12 12 12 16 20 20
3,500 3,870 4,350 6,760 7,080 7,380 7,670 7,960 8,230 8,740 9,230 9,440 13,800 10,400 11,600 12,400 17,800 28,800 29,800
4,040 4,740 5,810 8,170 8,840 9,520 10,200 10,900 11,500 12,900 14,300 13,900 23,500 16,600 20,000 22,800 37,800 64,100 69,400
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
873
NEEDLE ROLLER BEARINGS Shell Type Shell type needle roller bearings are lightweight with the lowest sectional height among needle roller bearings with outer ring, because they employ a shell type outer ring made from a thin special-steel plate which is accurately drawn, carburized and quenched. Series TLA UU Metric C
Series TLA UU are metric standard series of shell type needle roller bearings with cages, rollers and double seals. D
Fw
Bearing
Item No.
Inside Diameter Fw
Outside Diameter D
Width C
Dynamic
Basic Load Rating (Lbs.) Static
Pack Qty.
IKO-TLA1216UU IKO-TLA1416UU IKO-TLA2516UU
12 14 25
18 20 32
16 16 16
6,420 7,080 9,440
7,490 8,840 13,900
1 1 1
Machined Type Machined type needle roller bearings have an outer ring made by machining, heat treatment, and grinding. The outer ring has stable high rigidity and can be easily used even for light alloy housings. Series BR are inch standard series of machined type needle roller bearings with caged rollers. Series (R)NA UU Metric Series (R)NA UU are metric dimension 49 series of machine type needle roller bearings with caged rollers and double seals. w/o Inner Ring
A
C
C
D d
Fw
D
Fw
w/ Inner Ring
Item No.
Inside Diameter Fw
Item No.
Inside Diameter d
IKO-RNA4900UU IKO-RNA4901UU IKO-RNA4902UU IKO-RNA4903UU IKO-RNA4904UU IKO-RNA4922UU IKO-RNA4905UU IKO-RNA4928UU IKO-RNA4906UU IKO-RNA4932UU IKO-RNA4907UU IKO-RNA4908UU IKO-RNA4909UU IKO-RNA4910UU IKO-RNA4911UU IKO-RNA4912UU IKO-RNA4913UU IKO-RNA4914UU IKO-RNA4915UU IKO-RNA4916UU IKO-RNA4917UU
14 16 20 22 25 28 30 32 35 40 42 48 52 58 63 68 72 80 85 90 100
IKO-NA4900UU IKO-NA4901UU IKO-NA4902UU IKO-NA4903UU IKO-NA4904UU IKO-NA4922UU IKO-NA4905UU IKO-NA4928UU IKO-NA4906UU IKO-NA4932UU IKO-NA4907UU IKO-NA4908UU IKO-NA4909UU IKO-NA4910UU IKO-NA4911UU IKO-NA4912UU IKO-NA4913UU IKO-NA4914UU IKO-NA4915UU IKO-NA4916UU IKO-NA4917UU
10 12 15 17 20 22 25 28 30 32 35 40 45 50 55 60 65 70 75 80 85
Outside Dynamic Diameter Width Width Basic Load D C A Rating (Lbs.)
22 24 28 30 37 39 42 45 47 52 55 62 68 72 80 85 90 100 105 110 120
13 13 13 13 17 17 17 17 17 20 20 22 22 22 25 25 25 30 30 30 35
14 14 14 14 18 18 18 18 18 21 21 23 23 23 26 26 26 31 31 31 36
Static Basic Load Pack Rating (Lbs.) Qty.
8,080 8,470 9,570 10,300 18,000 18,300 20,300 21,000 21,500 29,400 30,100 37,200 38,900 41,300 52,200 54,500 56,800 76,900 79,600 80,700 103,000
8,490 9,320 11,600 13,100 20,500 23,700 25,100 26,800 28,400 44,200 46,300 58,400 63,400 71,100 85,700 92,800 99,800 143,000 153,000 158,000 225,000
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Series BR Inch
C
D
874
Fw
Bearing
Inner Ring
Item No.
Item No.
IKO-BR101812 IKO-BR122012 IKO-BR122016 IKO-BR142212 IKO-BR142216 IKO-BR162416 IKO-BR182616 IKO-BR182620 IKO-BR202816 IKO-BR202820 IKO-BR223016 IKO-BR223020 IKO-BR243316 IKO-BR243320 IKO-BR263516 IKO-BR263520 IKO-BR283716 IKO-BR283720 IKO-BR283820 IKO-BR303920 IKO-BR324116 IKO-BR324120 IKO-BR364824 IKO-BR364828 IKO-BR405224 IKO-BR405228 IKO-BR445624 IKO-BR445628 IKO-BR486024 IKO-BR486028 IKO-BR526828 IKO-BR526832 IKO-BR567232 IKO-BR607632 IKO-BR648032
IKO-LRB61012 IKO-LRB81212 IKO-LRB81216 IKO-LRB101412 IKO-LRB101416 — IKO-LRB141816 IKO-LRB141820 IKO-LRB162016 IKO-LRB162020 IKO-LRB182216 IKO-LRB182220 IKO-LRB202416 IKO-LRB202420 IKO-LRB222616 IKO-LRB222620 — — — IKO-LRB243020 IKO-LRB263216 IKO-LRB263220 IKO-LRB283624 IKO-LRB283628 IKO-LRB324024 IKO-LRB324028 IKO-LRB364424 IKO-LRB364428 IKO-LRB404824 IKO-LRB404828 IKO-LRB445228 IKO-LRB445232 IKO-LRB485632 IKO-LRB526032 IKO-LRB566432
Inside Diameter Fw 5
⁄8 ⁄4 ⁄4 7 ⁄8 7 ⁄8 1 1 1 ⁄8 11⁄8 11⁄4 11⁄4 13⁄8 13⁄8 11⁄2 11⁄2 15⁄8 15⁄8 13⁄4 13⁄4 13⁄4 17⁄8 2 2 21⁄4 21⁄4 21⁄2 21⁄2 23⁄4 23⁄4 3 3 31⁄4 31⁄4 31⁄2 33⁄4 4 3 3
Outside Diameter D
11⁄8 11⁄4 11⁄4 13⁄8 13⁄8 11⁄2 15⁄8 15⁄8 13⁄4 13⁄4 17⁄8 17⁄8 21⁄16 21⁄16 23⁄16 23⁄16 25⁄16 25⁄16 23⁄8 27⁄16 29⁄16 29⁄16 3 3 31⁄4 31⁄4 31⁄2 31⁄2 33⁄4 33⁄4 41⁄4 41⁄4 41⁄2 43⁄4 5
Basic Load Rating (Lbs.) Width C 3
⁄4 ⁄4 1 3 ⁄4 1 1 1 11⁄4 1 11⁄4 1 11⁄4 1 11⁄4 1 11⁄4 1 11⁄4 11⁄4 11⁄4 1 11⁄4 11⁄2 13⁄4 11⁄2 13⁄4 11⁄2 13⁄4 11⁄2 13⁄4 13⁄4 2 2 2 2 3
Dynamic
Static
Pack Qty.
18,900 21,700 27,600 23,000 29,100 32,100 34,900 43,200 36,000 44,600 38,500 47,700 43,700 54,200 44,800 55,600 47,500 58,900 58,900 60,100 51,000 63,200 90,300 10,500 94,600 110,000 98,700 114,000 10,500 122,000 141,000 154,000 162,000 169,000 176,000
19,700 24,400 33,100 27,100 36,800 42,300 49,900 65,600 53,500 70,300 60,000 78,900 66,900 88,200 70,900 93,400 78,200 103,000 103,000 108,000 89,400 118,000 158,000 191,000 174,000 210,000 189,000 228,000 211,000 255,000 259,000 290,000 316,000 342,000 368,000
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
NEEDLE ROLLER BEARINGS Machined Type Machined type needle roller bearings have an outer ring made by machining, heat treatment, and grinding. The outer ring has stable high rigidity and can be easily used even for light alloy housings. Series BR are inch standard series of machined type needle roller bearings with caged rollers. C
Series TAF(I) Metric Dd
Fw
Series TAF(I) are metric light duty series of machined type needle roller bearings with caged rollers. w/ Inner Ring
w/o Inner Ring
Item No.
Inside Diameter mm d
Item No.
Inside Diameter mm Fw
Outside Diameter mm D
Width mm C
Dynamic Basic Load Rating (Lbs.)
Static Basic Load Rating (Lbs.)
Pack Qty.
IKO-TAFI51512 IKO-TAFI51516 IKO-TAFI61612 IKO-TAFI61616 IKO-TAFI71712 IKO-TAFI71716 IKO-TAFI91912 IKO-TAFI91916 IKO-TAFI102216 IKO-TAFI102220 — — IKO-TAFI122416 IKO-TAFI122420 — — — — IKO-TAFI152716 IKO-TAFI152720 — — IKO-TAFI172916 IKO-TAFI172920 — — IKO-TAFI203216 IKO-TAFI203220 — — IKO-TAFI223416 IKO-TAFI223420 — — IKO-TAFI253820 IKO-TAFI253830 — — IKO-TAFI284220 IKO-TAFI284230 IKO-TAFI304520 IKO-TAFI304530 IKO-TAFI324720 IKO-TAFI324730 — — IKO-TAFI355020 IKO-TAFI355030 — — IKO-TAFI385320 IKO-TAFI385330 IKO-TAFI405520 IKO-TAFI405530 IKO-TAFI425720 IKO-TAFI425730 IKO-TAFI456225 IKO-TAFI456235 IKO-TAFI506825 IKO-TAFI506835
5 5 6 6 7 7 9 9 10 10 — — 12 12 — — — — 15 15 — — 17 17 — — 20 20 — — 22 22 — — 25 25 — — 28 28 30 30 32 32 — — 35 35 — — 38 38 40 40 42 42 45 45 50 50
IKO-TAF81512 IKO-TAF81516 IKO-TAF91612 IKO-TAF91616 IKO-TAF101712 IKO-TAF101716 IKO-TAF121912 IKO-TAF121916 IKO-TAF142216 IKO-TAF142220 IKO-TAF152316 IKO-TAF152320 IKO-TAF162416 IKO-TAF162420 IKO-TAF172516 IKO-TAF172520 IKO-TAF182616 IKO-TAF182620 IKO-TAF192716 IKO-TAF192720 IKO-TAF202816 IKO-TAF202820 IKO-TAF212916 IKO-TAF212920 IKO-TAF223016 IKO-TAF223020 IKO-TAF243216 IKO-TAF243220 IKO-TAF253316 IKO-TAF253320 IKO-TAF263416 IKO-TAF263420 IKO-TAF283720 IKO-TAF283730 IKO-TAF293820 IKO-TAF293830 IKO-TAF304020 IKO-TAF304030 IKO-TAF324220 IKO-TAF324230 IKO-TAF354520 IKO-TAF354530 IKO-TAF374720 IKO-TAF374730 IKO-TAF384820 IKO-TAF384830 IKO-TAF405020 IKO-TAF405030 IKO-TAF425220 IKO-TAF425230 IKO-TAF435320 IKO-TAF435330 IKO-TAF455520 IKO-TAF455530 IKO-TAF475720 IKO-TAF475730 IKO-TAF506225 IKO-TAF506235 IKO-TAF556825 IKO-TAF556835
8 8 9 9 10 10 12 12 14 14 15 15 16 16 17 17 18 18 19 19 20 20 21 21 22 22 24 24 25 25 26 26 28 28 29 29 30 30 32 32 35 35 37 37 38 38 40 40 42 42 43 43 45 45 47 47 50 50 55 55
15 15 16 16 17 17 19 19 22 22 23 23 24 24 25 25 26 26 27 27 28 28 29 29 30 30 32 32 33 33 34 34 37 37 38 38 40 40 42 42 45 45 47 47 48 48 50 50 52 52 53 53 55 55 57 57 62 62 68 68
12 16 12 16 12 16 12 16 16 20 16 20 16 20 16 20 16 20 16 20 16 20 16 20 16 20 16 20 16 20 16 20 20 30 20 30 20 30 20 30 20 30 20 30 20 30 20 30 20 30 20 30 20 30 20 30 25 35 25 35
5,060 7,080 5,490 7,680 5,880 8,230 6,610 9,250 11,700 14,800 12,300 15,600 12,300 15,500 12,900 16,300 13,400 17,000 14,000 17,700 13,900 17,600 14,400 18,200 14,900 18,900 15,300 19,400 15,800 20,000 16,300 20,600 21,700 31,100 21,600 30,900 25,100 36,000 25,700 36,800 26,900 38,600 28,200 40,500 28,100 40,300 29,400 42,300 29,900 43,000 30,500 43,800 31,000 44,600 31,500 45,200 43,000 58,000 45,400 61,200
4,690 7,220 5,330 8,210 5,970 9,190 7,260 11,200 13,700 18,600 14,900 20,200 15,100 20,400 16,300 22,000 17,500 23,600 18,700 25,300 18,800 25,400 20,000 27,100 21,200 28,700 22,500 30,500 23,700 32,100 24,900 33,800 37,100 58,900 37,200 59,100 40,100 63,900 42,200 67,200 46,200 73,600 50,100 79,800 50,200 80,000 54,100 86,200 56,200 89,400 58,200 92,600 60,200 95,800 62,200 99,100 85,300 125,000 94,000 138,000
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Series (R)NA Metric Series (R)NA are metric standard duty series of machined type needle roller bearings with caged rollers. w/ Inner Ring
C
D d
Fw
w/o Inner Ring
Item No.
Inside Diameter mm d
Item No.
Inside Diameter mm Fw
Outside Diameter mm D
Width mm C
Dynamic Basic Load Rating (Lbs.
Static Basic Load Rating (Lbs.)
Pack Qty.
IKO-NA498 IKO-NA499 IKO-NA4900 IKO-NA4901 IKO-NA4902 IKO-NA4903 IKO-NA4904 IKO-NA4922 IKO-NA4905 IKO-NA4928 IKO-NA4906 IKO-NA4932 IKO-NA4907 IKO-NA4908 IKO-NA4909 IKO-NA4910
8 9 10 12 15 17 20 22 25 28 30 32 35 40 45 50
IKO-RNA498 IKO-RNA499 IKO-RNA4900 IKO-RNA4901 IKO-RNA4902 IKO-RNA4903 IKO-RNA4904 IKO-RNA4922 IKO-RNA4905 IKO-RNA4928 IKO-RNA4906 IKO-RNA4932 IKO-RNA4907 IKO-RNA4908 IKO-RNA4909 IKO-RNA4910
10 12 14 16 20 22 25 28 30 32 35 40 42 48 52 58
19 20 22 24 28 30 37 39 42 45 47 52 55 62 68 72
11 11 13 13 13 13 17 17 17 17 17 20 20 22 22 22
6,180 6,600 9,230 9,660 10,900 11,700 21,000 21,400 23,700 24,500 25,200 31,200 32,000 41,600 43,500 46,200
5,030 6,310 10,100 11,100 13,800 15,600 25,000 28,900 30,700 32,700 34,700 47,800 50,100 67,400 73,300 82,100
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
875
HIGH PRECISION BALL BEARINGS Flanged and Flanged Extended Inner Rings Inch
C
C
A B
B A
Flanged C
Bearings are made of 440C stainless steel and are corrosion, fatigue and wear resistant. Temperature range is -70 degrees Fahrenheit to 350 degrees Fahrenheit. Bearings have steel shields. Applications include idler pulleys, small gear trains, pumps tape guides, synchros and servos. These bearings meet or exceed ABEC 5 tolerances. Radial clearance is .0002/.0005". All extended inner ring bearings are .031" wider than C dimension on inner ring. Standard and Standard Extended Inner Rings Inch
Standard
Standard Extended
Item No.
Item No.
A
B
C
DMB-1 DMB-2 DMB-3 DMB-4 DMB-5 DMB-6 DMB-7 DMB-8 DMB-9 DMB-10 DMB-11 DMB-12 DMB-13 DMB-14 DMB-15 DMB-16 DMB-17 DMB-18 DMB-98 DMB-99 DMB-100
— — DMB-36 DMB-37 DMB-38 DMB-39 DMB-40 DMB-41 DMB-42 — DMB-43 DMB-44 DMB-45 DMB-46 DMB-47 DMB-48 DMB-49 DMB-50 — — —
.0469 .0550 .0781 .0937 .0937 .1250 .1250 .1250 .1250 .1250 .1562 .1875 .1875 .1875 .2500 .2500 .2500 .3125 .2500 .3750 .5000
.1562 .1875 .2500 .1875 .3125 .2500 .3125 .3750 .3750 .5000 .3125 .3125 .3750 .5000 .3750 .5000 .6250 .5000 .7500 .8750 1.1250
.0937 .1094 .1406 .0937 .1406 .1094 .1406 .1406 .1562 .1719 .1250 .1250 .1250 .1960 .1250 .1875 .1960 .1562 .2812 .2812 .3125
Dynamic Load Rating Lbs. Max. rpm
31 52 70 43 124 64 124 144 144 144 81 81 160 293 84 243 335 122 524 748 880
Pack Qty.
120,000 110,000 80,000 95,000 71,000 80,000 71,000 63,000 63,000 63,000 63,000 63,000 60,000 50,000 56,000 50,000 45,000 48,000 43,000 38,000 20,000
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Note: Extended inner ring bearings are .031 wider than C dimension on inner ring.
B A
Flanged Extended Inner Ring
Bearings are made of 440C stainless steel and are corrosion, fatigue and wear resistant. Temperature range is -70 degrees Fahrenheit to 350 degrees Fahrenheit. Bearings have steel shields. Applications include idler pulleys, small gear trains, pumps tape guides, synchros and servos. These bearings meet or exceed ABEC 5 tolerances. Radial clearance is .0002/.0005". All extended inner ring bearings are .031" wider than C dimension on inner ring. Flanged
Flanged Extended
Item No.
Item No.
DMB-20 DMB-21 DMB-22 DMB-24 DMB-26 DMB-25 DMB-27 DMB-29 DMB-30 DMB-31 DMB-32 DMB-33 DMB-34 DMB-35
— — DMB-51 DMB-52 DMB-54 DMB-53 DMB-55 DMB-57 DMB-58 — DMB-59 DMB-60 — DMB-61
Flange Flange OD Thickness
.234 .296 .294 .296 .422 .359 .440 .359 .422 .565 .422 .547 .690 .547
.031 .031 .031 .031 .031 .031 .030 .036 .031 .042 .036 .045 .042 .031
A
B
C
Dynamic Load Rating Lbs.
.0550 .0781 .0937 .1250 .1250 .1250 .1250 .1875 .1875 .1875 .2500 .2500 .2500 .3125
.1875 .2500 .1875 .2500 .3750 .3125 .3750 .3125 .3750 .5000 .3750 .5000 .6250 .5000
.1094 .1406 .0937 .1094 .1406 .1406 .1562 .1250 .1250 .1960 .1250 .1875 .1960 .1562
52 70 43 64 144 124 144 81 160 293 84 243 335 122
Pack Max rpm Qty.
110,000 80,000 95,000 80,000 63,000 71,000 63,000 63,000 60,000 50,000 56,000 50,000 45,000 48,000
1 1 1 1 1 1 1 1 1 1 1 1 1 1
Note: Extended inner ring bearings are .031 wider than C dimension on inner ring. C
Flanged Metric
Standard Extra Thin Inch
B A
Item No.
A
B
C
Dynamic Load Rating Lbs.
Max rpm
Pack Qty.
DMB-101 DMB-102 DMB-103 DMB-104
.3750 .5000 .6250 .7500
.6250 .7500 .8750 1.0000
.1562 .1562 .1562 .1562
93 108 112 123
30,000 24,000 20,000 16,000
1 1 1 1
Standard Metric
Flanged
Bearings are made of 440C stainless steel and are corrosion, fatigue and wear resistant. Temperature range is -70 degrees Fahrenheit to 350 degrees Fahrenheit. Bearings have steel shields. Applications include idler pulleys, small gear trains, pumps tape guides, synchros and servos. These bearings meet or exceed P5 (ISO) for metric bearings.
Item No.
A
B
C
Dynamic Load Rating Lbs.
Max rpm
Pack Qty.
Item No.
A
B
C
OD
Thickness
Dynamic Load Rating Lbs.
Max. rpm
Pack Qty.
DMB-62 DMB-63 DMB-64 DMB-65 DMB-66 DMB-67 DMB-68 DMB-69 DMB-70 DMB-71 DMB-72 DMB-73 DMB-74 DMB-75 DMB-76 DMB-77 DMB-78 DMB-79
4 4 4 4 5 5 5 5 5 5 6 6 6 7 8 8 8 9
10 11 12 13 8 9 10 11 13 14 10 12 13 14 12 14 16 17
4.0 4.0 4.0 5.0 2.5 3.0 4.0 4.0 4.0 5.0 3.0 4.0 5.0 5.0 3.5 4.0 5.0 5.0
60 98 98 133 31 44 44 73 110 135 51 73 110 120 56 83 128 136
56,000 53,000 53,000 48,000 63,000 60,000 60,000 53,000 50,000 48,000 53,000 50,000 48,000 45,000 48,000 45,000 43,000 43,000
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
DMB-80 DMB-81 DMB-82 DMB-83 DMB-84 DMB-85 DMB-86 DMB-87 DMB-88 DMB-89 DMB-90 DMB-91 DMB-92 DMB-93 DMB-94 DMB-95 DMB-96 DMB-97
4 4 4 4 5 5 5 5 5 5 6 6 6 7 8 8 8 9
10 11 12 13 8 9 10 11 13 14 10 12 13 14 12 14 16 17
4.0 4.0 4.0 5.0 2.5 3.0 4.0 4.0 4.0 5.0 3.0 4.0 5.0 5.0 3.5 4.0 5.0 5.0
11.6 12.5 13.5 15.0 9.2 10.2 11.6 12.6 15.0 16.0 11.2 13.6 15.0 16.0 13.6 15.6 18.0 19.0
.8 1.0 1.0 1.0 .6 .6 .8 .8 1.0 1.0 .6 .8 1.1 1.1 .8 .8 1.1 1.1
60 98 98 133 31 44 44 73 110 135 51 73 110 120 56 83 128 136
56,000 53,000 53,000 48,000 63,000 60,000 60,000 53,000 50,000 48,000 53,000 50,000 48,000 45,000 48,000 45,000 43,000 43,000
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
876
Flange
BALL BEARINGS Nice® Ball Bearings
C
A
Double Sealed
B
Double Shield
Precision ground on all contact surfaces. Careful heat treatment provides a uniform and exact degree of hardness for maximum life. A ball retainer is used to increase the range of allowable speeds by reducing ball-to-ball contact friction. Bearings are supplied grease packed. Recommended for medium loads and for maximum speeds in the range of 5,000 rpm. ID and OD tolerances are +.0000/.0005". Width tolerance is +.0000/-.005". Double Sealed
Double Shielded
Item No.
Item No.
A
B
C
Dynamic Load Capacity
Static Load Capacity
Pack Qty.
SKF-1603DC* SKF-1604DC* SKF-1605DC SKF-1606DC SKF-1607DC SKF-1614DC SKF-1615DC SKF-1616DC SKF-1621DC SKF-1623DC SKF-1628DC SKF-1630DC SKF-1633DC SKF-1635DC SKF-1638DC** SKF-1640DC** SKF-1641DC** SKF-1652DC*** SKF-1654DC*** SKF-1657DC*** —
SKF-1603DS — SKF-1605DS SKF-1606DS SKF-1607DS SKF-1614DS SKF-1615DS SKF-1616DS SKF-1621DS SKF-1623DS SKF-1628DS SKF-1630DS SKF-1633DS SKF-1635DS SKF-1638DS SKF-1640DS SKF-1641DS SKF-1652DS SKF-1654DS SKF-1657DS SKF-1604DS
.3125 .3750 .3125 .3750 .4375 .3750 .4375 .5000 .5000 .6250 .6250 .7500 .6250 .7500 .7500 .8750 1.0000 1.1250 1.2500 1.2500 .3750
.8750 .8750 .9063 .9063 .9063 1.1250 1.1250 1.1250 1.3750 1.3750 1.6250 1.6250 1.7500 1.7500 2.0000 2.0000 2.0000 2.5000 2.5000 2.5625 .8750
.2813 .3438 .3125 .3125 .3125 .3750 .3750 .3750 .4375 .4375 .5000 .5000 .5000 .5000 .5625 .5625 .5625 .6250 .6250 .6875 .2813
644 644 698 698 698 1,200 1,200 1,200 1,878 1,878 2,600 2,600 2,600 2,600 2,967 2,967 2,967 3,864 3,864 5,360 644
255 255 300 300 300 475 475 475 850 850 1,010 1,010 1,025 1,025 1,350 1,350 1,350 2,120 2,120 2,620 255
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
*Width is .3438" **OD Tolerance +.0000/-.0006 ***Multi-part seals. OD Tolerance +.0000/-.0006
Semi-ground Radial Bearings
Unground Thrust Bearings A TO CLEAR r
B
C
A1 C A B
Precision ground on all contact surfaces except bore. A ball retainer, or separator, is employed to increase the range of allowable speeds by reducing ball contact friction. This series of radial bearing is available open, double shielded or double sealed. The double shielded and double sealed bearings are grease packed as standard. Recommended for lighter loads and maximum speeds in the range of 3,000 rpm. ID tolerance is +.005/-.000, OD tolerance is +.0000/-.0005 and width tolerance is +.0000/-.005. Double Sealed Double Shielded Item No.
Item No.
A
B
C
r
Dynamic Load Capacity
SKF-9215* SKF-9220 SKF-9225 SKF-9230 SKF-9235 SKF-9240 SKF-9245 SKF-9250** SKF-9255** SKF-9265** —
SKF-9270 SKF-9280 SKF-9285 SKF-9290 SKF-9295 SKF-9300 SKF-9305 SKF-9310 SKF-9315 SKF-9320 SKF-9275
.2500 .3750 .3750 .4375 .4375 .5000 .5000 .5000 .5625 .5625 .2813
.6875 1.1250 1.1250 1.3750 1.3750 1.6250 1.6250 1.7500 2.0000 2.0000 .8750
.2500 .3750 .5000 .5000 .6250 .6250 .7500 .7500 .7500 1.0000 .3750
.035 .035 .035 .035 .035 .035 .035 .035 .035 .035 .035
255 600 600 940 940 1,300 1,300 1,300 1,480 1,480 325
*Multi-part seal; Width is 0.3125 **OD tolerance +.0000/-.0006
Static Load Pack Capacity Qty.
170 475 475 850 850 1,010 1,010 1,025 1,350 1,350 255
1 1 1 1 1 1 1 1 1 1 1
Unground thrust bearings are designed for moderate speeds and medium thrust loads. These bearings utilize a full ball complement. The upper ring is free to rotate in the band and has a close fit in the bore for the shaft. The lower ring is fixed in the band and has a shaft clearance in the bore. Recommended for maximum speeds in the range of 1,200 rpm. Item No.
A
A1
B
C
No.
Balls Size
Speed Limit (rpm)
Pack Qty.
SKF-9035 SKF-9040 SKF-9045 SKF-9050 SKF-9055 SKF-9060 SKF-9065 SKF-9070 SKF-9075 SKF-9080 SKF-9085 SKF-9090 SKF-9095 SKF-9100 SKF-9105 SKF-9110 SKF-9115 SKF-9120
.250 .375 .453 .500 .500 .625 .625 .750 .875 .9843 1.000 1.000 1.016 1.063 1.125 1.250 1.437 1.500
.275 .400 .478 .525 .525 .656 .656 .775 .900 1.031 1.075 1.031 1.031 1.094 1.150 1.275 1.462 1.525
.844 1.047 .859 1.266 1.000 1.125 1.422 1.656 1.891 1.750 2.000 1.969 1.750 1.969 2.094 2.344 2.469 2.594
.333 .359 .281 .437 .344 .344 .453 .545 .594 .625 .630 .625 .625 .625 .625 .625 .625 .625
10 14 15 10 12 16 12 15 17 16 12 18 16 18 19 23 23 25
.156 .156 .125 .250 .188 .156 .250 .250 .250 .250 .375 .250 .250 .250 .250 .250 .250 .250
1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
877
BALL BEARINGS 1600 Series Inch
Specifically designed for applications where space limitations are a primary consideration and shafts are relatively A B large. Available with metal shields or Buna N seals. The 6000 series is capable of withstanding radial and thrust loads within the limitations of their ball complement. The conrad construction of the R series enables these bearings to take a thrust load as well as a radial load. The well designed ball complement and selection of retainers permit use of this series in high speed motor applications. This series is produced open, shielded or sealed. Shield and sealed bearings are made slightly wider as shown in the dimension table. Metric dimensions are in millimeters. C
C
A
B
Open Metric Designed to be dimensionally interchangeable with standard domestic inch series bearings. By using 52100 steel and holding dimensions to ABEC 1 tolerances, this series offers economy with electric motor quality. Close tolerance and improved ball complement allow an increased load capacity. This series is available with shields and seals. Metric dimensions are in millimeters. Double Sealed Double Shielded
Dynamic Static Load Load Capacity Capacity
Item No.
Item No.
A
B
C
PRB-267 PRB-268 PRB-269 PRB-270 PRB-271 PRB-272 PRB-273 PRB-274 PRB-275 PRB-276 PRB-277 PRB-278 PRB-279 PRB-280 PRB-281 PRB-282 PRB-283 PRB-284 PRB-285 — — —
PRB-287 PRB-288 PRB-289 PRB-290 PRB-291 PRB-292 PRB-293 PRB-294 PRB-295 PRB-296 PRB-297 PRB-298 — PRB-300 — PRB-302 PRB-303 — PRB-305 PRB-299 PRB-301 PRB-304
.3125 .3750 .3125 .3750 .4375 .3750 .4375 .5000 .5000 .6250 .6250 .7500 .6250 .7500 .7500 .8750 1.0000 1.1250 1.2500 .7500 .7500 1.1250
.8750 .8750 .9063 .9063 .9063 1.1250 1.1250 1.1250 1.3750 1.3750 1.6250 1.6250 1.7500 1.7500 2.0000 2.0000 2.0000 2.5000 2.5000 1.6250 2.0000 2.5000
.3437 .3437 .3125 .3125 .3125 .3750 .3750 .3750 .4375 .4375 .5000 .5000 .5000 .5000 .5625 .5625 .5625 .6250 .6250 .5000 .5625 .8250
644 644 698 698 698 1,200 1,200 1,200 1,878 1,878 2,600 2,600 2,600 2,600 2,967 2,967 2,967 3,864 3,864 2,600 2,697 3,864
255 255 300 300 300 475 475 475 850 850 1,010 1,010 1,025 1,025 1,350 1,350 1,350 2,120 2,120 1,010 1,350 2,120
Pack Qty.
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Item No.
A
B
C
Bearing Designation
Pack Qty.
PRB-37 PRB-38 PRB-39 PRB-40 PRB-41 PRB-42 PRB-43 PRB-44 PRB-52 PRB-53 PRB-54 PRB-56 PRB-55 PRB-57
8 10 12 15 17 20 25 30 10 12 15 20 17 25
22 26 28 32 35 42 47 55 35 37 42 52 47 62
7 8 8 9 10 12 12 13 11 12 13 15 14 17
608 6000 6001 6002 6003 6004 6005 6006 6300 6301 6302 6304 6303 6305
1 1 1 1 1 1 1 1 1 1 1 1 1 1
Item No.
A
B
C
Bearing Designation
Pack Qty.
PRB-79 PRB-80 PRB-81 PRB-82 PRB-83 PRB-84 PRB-85 PRB-86 PRB-94 PRB-95 PRB-96 PRB-97 PRB-98 PRB-99
8 10 12 15 17 20 25 30 10 12 15 17 20 25
22 26 28 32 35 42 47 55 35 37 42 7 52 62
7 8 8 9 10 12 12 13 11 12 13 14 15 17
608 6000 6001 6002 6003 6004 6005 6006 6300 6301 6302 6303 6304 6305
1 1 1 1 1 1 1 1 1 1 1 1 1 1
Item No.
A
B
C
Bearing Designation
Pack Qty.
PRB-58 PRB-59 PRB-60 PRB-61 PRB-62 PRB-63 PRB-64 PRB-65 PRB-73 PRB-74 PRB-75 PRB-76 PRB-77 PRB-78
8 10 12 15 17 20 25 30 25 12 15 17 20 25
22 26 28 32 35 42 47 55 52 37 42 47 52 62
7 8 8 9 10 12 12 13 15 12 13 14 15 17
608 6000 6001 6002 6003 6004 6005 6006 6300 6301 6302 6303 6304 6305
1 1 1 1 1 1 1 1 1 1 1 1 1 1
Shield Metric Series Double Sealed Metric
Sealed Double Row Ball Bearing Metric
Shield Metric Series Double Shielded Metric
C
B A
Load Rating Lbs.
Item No.
A
B
C
Dynamic
Static
Bearing No.
Pack Qty.
PRB-100 PRB-101 PRB-102 PRB-103 PRB-104 PRB-105 PRB-106
10 12 15 17 20 25 30
30 32 35 30 47 52 62
14.3 15.9 15.9 17.5 20.6 20.6 23.8
1,810 2,390 2,650 3,350 4,450 4,850 6,700
1,030 1,320 1,590 2,040 2,850 3,350 4,800
5200-2RS 5201-2RS 5202-2RS 5203-2RS 5204-2RS 5205-2RS 5206-2RS
1 1 1 1 1 1 1
878
BALL BEARINGS Deep Groove Ball Bearings Single Row For Electric Motors
Deep Groove 6200 Series Metric This deep groove, conrad construction is specifically designed to provide maximum performance by means of precise ball complement selection. The honed raceways offer a perfectly balanced bearing capable of operating under straight radial, thrust or combination loads. This series is available with shields. Buna N seals, or locating rings. Sealed bearings may be obtained with either low or high starting torques. Radial clearance is selected in accordance to applications ranging from C2 - C0 - C3 - C4 fits. Metric dimensions are in millimeters.
C
Single row deep groove ball bearings have deep uninterrupted raceways and a high degree of conformity between balls and raceways. This enables them to carry axial loads in both directions, in addition to radial loads, even at high speeds. Bearings with shields or seals at both sides are filled with a grease which has good rust inhibiting properties suitable of operating temperatures of -22 to +230 degrees Fahrenheit. All bearings have a pressed cage of sheet steel and are available either plain, shields on both sides (2 Z), or two rubber seals on both sides (2 RS). All dimensions are in millimeters.
B
A
Double Sealed Metric
C
B
C
A
B
Open
Two Shields
A
Two Seals
Basic Load Rating lbs.
Speed Rating rpm
Item No.
A
B
C
Dynamic
Static
Grease
Oil
Bearing No.
Pack Qty.
PRB-256 PRB-257 PRB-258 PRB-259 PRB-260 PRB-261 PRB-262 PRB-263 PRB-264 PRB-265 PRB-266
10 12 15 17 20 25 30 35 40 45 50
30 32 35 40 47 52 62 72 80 85 90
9 10 11 12 14 15 16 17 18 19 20
1,140 1,550 1,750 2,150 2,860 3,150 4,380 5,730 6,900 7,460 7,890
531 697 843 1,070 1,470 1,750 2,520 3,440 4,270 4,860 5,220
17,000 15,000 13,000 12,000 10,000 8,500 7,500 6,300 5,600 5,000 4,000
— — — — — — — — — — —
6200-2RS-C3 6201-2RS-C3 6202-2RS-C3 6203-2RS-C3 6204-2RS-C3 6205-2RS-C3 6206-2RS-C3 6207-2RS-C3 6208-2RS-C3 6209-2RS-C3 6210-2RS-C3
1 1 1 1 1 1 1 1 1 1 1
Double Shielded Metric
Open
Basic Load Rating Lbs.
Speed Rating RPM
Item No.
SKF
A
B
C
Dynamic
Static
Grease
Oil
Pack Qty.
SKF-01 SKF-02 SKF-03 SKF-04 SKF-05 SKF-06 SKF-07 SKF-08 SKF-09 SKF-010 SKF-011
6200JEM 6201JEM 6202JEM 6203JEM 6204-JEM 6205JEM 6206JEM 6207JEM 6208JEM 6209JEM 6210JEM
10 12 15 17 20 25 30 35 40 45 50
30 32 35 40 47 52 62 72 80 85 90
9 10 11 12 14 15 16 17 18 19 20
1,140 1,550 1,750 2,150 2,860 3,150 4,380 5,730 6,900 7,460 7,890
531 697 843 1,070 1,470 1,750 2,520 3,440 4,270 4,860 5,220
24,000 22,000 19,000 17,000 15,000 12,000 10,000 9,000 8,500 7,500 7,000
30,000 28,000 24,000 20,000 18,000 15,000 13,000 11,000 10,000 9,000 8,500
1 1 1 1 1 1 1 1 1 1 1
Two Shields Basic Load Rating Lbs.
Item No.
SKF
A
B
C
SKF-012 SKF-013 SKF-014 SKF-015 SKF-016 SKF-017 SKF-018 SKF-019 SKF-020 SKF-021 SKF-022
6200-2ZJEM 6201-2ZJEM 6202-2ZJEM 6203-2ZJEM 6204-2ZJEM 6205-2ZJEM 6206-2ZJEM 6207-2ZJEM 6208-2ZJEM 6209-2ZJEM 6210-2ZJEM
10 12 15 17 20 25 30 35 40 45 50
30 32 35 40 47 52 62 72 80 85 90
9 10 11 12 14 15 16 17 18 19 20
Dynamic Static
1,140 1,550 1,750 2,150 2,860 3,150 4,380 5,730 6,900 7,460 7,890
531 697 843 1,070 1,470 1,750 2,520 3,440 4,270 4,860 5,220
Speed Rating RPM Grease
Oil
Pack Qty.
24,000 22,000 19,000 17,000 15,000 12,000 10,000 9,000 8,500 7,500 7,000
30,000 28,000 24,000 20,000 18,000 15,000 13,000 11,000 10,000 9,000 8,500
1 1 1 1 1 1 1 1 1 1 1
Basic Load Rating lbs.
Speed Rating rpm
Item No.
A
B
C
Dynamic
Static
Grease
Oil
Bearing No.
Pack Qty.
PRB-245 PRB-246 PRB-247 PRB-248 PRB-249 PRB-250 PRB-251 PRB-252 PRB-253 PRB-254 PRB-255
10 12 15 17 20 25 30 35 40 45 50
30 32 35 40 47 52 62 72 80 85 90
9 10 11 12 14 15 16 17 18 19 20
1,140 1,550 1,750 2,150 2,860 3,150 4,380 5,730 6,900 7,460 7,890
531 697 843 1,070 1,470 1,750 2,520 3,440 4,270 4,860 5,220
24,000 22,000 19,000 17,000 15,000 12,000 10,000 9,000 8,500 7,500 7,000
30,000 28,000 24,000 20,000 18,000 15,000 13,000 11,000 10,000 9,000 8,500
6200-ZZ-C3 6201-ZZ-C3 6202-ZZ-C3 6203-ZZ-C3 6204-ZZ-C3 6205-ZZ-C3 6206-ZZ-C3 6207-ZZ-C3 6208-ZZ-C3 6209-ZZ-C3 6210-ZZ-C3
1 1 1 1 1 1 1 1 1 1 1
Open Metric
Two Seals
Basic Load Rating Lbs.
Speed Rating RPM
Item No.
SKF
A
B
C
Dynamic
Static
Grease
SKF-023 SKF-024 SKF-025 SKF-026 SKF-027 SKF-028 SKF-029 SKF-030 SKF-031 SKF-032 SKF-033
6200-2RSJEM 6201-2RSJEM 6202-2RSJEM 6203-2RSJEM 6204-2RSJEM 6205-2RSJEM 6206-2RSJEM 6207-2RSJEM 6208-2RSJEM 6209-2RSJEM 6210-2RSJEM
10 12 15 17 20 25 30 35 40 45 50
30 32 35 40 47 52 62 72 80 85 90
9 10 11 12 14 15 16 17 18 19 20
1,140 1,550 1,750 2,150 2,860 3,150 4,380 5,730 6,900 7,460 7,890
531 697 843 1,070 1,470 1,750 2,520 3,440 4,270 4,860 5,220
17,000 15,000 13,000 12,000 10,000 8,500 7,500 6,300 5,600 5,000 4,000
Basic Load Rating lbs.
Speed Rating rpm
Oil
Pack Qty.
Item No.
A
B
C
Dynamic
Static
Grease
Oil
Bearing No.
Pack Qty.
— — — — — — — — — — —
1 1 1 1 1 1 1 1 1 1 1
PRB-234 PRB-235 PRB-236 PRB-237 PRB-238 PRB-239 PRB-240 PRB-241 PRB-242 PRB-243 PRB-244
10 12 15 17 20 25 30 35 40 45 50
30 32 35 40 47 52 62 72 80 85 90
9 10 11 12 14 15 16 17 18 19 20
1,140 1,550 1,750 2,150 2,860 3,150 4,380 5,730 6,900 7,460 7,890
531 697 843 1,070 1,470 1,750 2,520 3,440 4,270 4,860 5,220
24,000 22,000 19,000 17,000 15,000 12,000 10,000 9,000 8,500 7,500 7,000
30,000 28,000 24,000 20,000 18,000 15,000 13,000 11,000 10,000 9,000 8,500
6200-C3 6201-C3 6202-C3 6203-C3 6204-C3 6205-C3 6206-C3 6207-C3 6208-C3 6209-C3 6210-C3
1 1 1 1 1 1 1 1 1 1 1
879
BALL BEARINGS Single Row Radial Inch and Metric
These popular bearings are used in a wide range of applications such as motors, pumps, etc. Designed to carry both radial and axial loads. Double shielded bearings have metal shields on the sides. Double sealed have two contact seals made out of synthetic rubber. Metric dimensions are shown in millimeters. Plain
C
A
Plain Item No.
Inch NB-1010 NB-1025 NB-1040 NB-1055 NB-1070 NB-1085 NB-1100 — NB-1120
Double Shielded
5
⁄32 ⁄32 ⁄32 7 ⁄32 1 ⁄4 9 ⁄32 5 ⁄16 — 3 ⁄8 5 7
Double Sealed
Item No.
C
Item No.
C
NB-1020 NB-1035 NB-1050 NB-1065 NB-1080 NB-1095 NB-1105 NB-1115 NB-1130
5 ⁄32 .196 9 ⁄32 9 ⁄32 5 ⁄16 11 ⁄32 7 ⁄16 1 ⁄2 1 ⁄2
NB-1015 NB-1030 NB-1045 NB-1060 NB-1075 NB-1090 — — NB-1125
5 ⁄32 .196 9 ⁄32 9 ⁄32 5 ⁄16 11 ⁄32 — — 1 ⁄2
C
C
A
Plain Inch
B
B
A
B
1
3
⁄8 ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ 1
3
16 1 4 3 8 1 2 5 8 3 4 7 8
Bearing Pack Designation Qty.
⁄8 ⁄2 ⁄4 7 ⁄8 11⁄8 13⁄8 15⁄8 17⁄8 2 1
3
R2 R3 R4A R6 R8 R10 R12 R14 R16
1 1 1 1 1 1 1 1 1
Double Sealed
C
Item No.
C
Item No.
C
A
B
Metric — — INA-2015 — — — — INA-2040 — — INA-2055 — INA-2065 — INA-2075 — — — — — —
— — 8 — — — — 13 — — 11 — 14 — 16 — — — — — —
INA-2125 INA-2130 INA-2135 INA-2140 INA-2145 INA-2150 INA-2155 INA-2160 INA-2165 INA-2170 INA-2175 INA-2180 INA-2185 INA-2190 — — — — — — —
7 8 8 9 10 12 12 13 9 10 11 12 14 15 — — — — — — —
— INA-2255 INA-2260 INA-2265 INA-2270 INA-2275 INA-2280 INA-2285 INA-2290 INA-2295 INA-2300 INA-2305 INA-2310 INA-2315 INA-2320 INA-2325 INA-2330 INA-2335 INA-2340 INA-2345 INA-2350
— 8 8 9 10 12 12 13 9 10 11 12 14 15 16 11 12 13 14 15 17
8 10 12 15 17 20 25 30 10 12 15 17 20 25 30 10 12 15 17 20 25
22 26 28 32 35 42 47 55 30 32 35 40 47 52 62 35 37 42 47 52 62
Bearing Pack Designation Qty.
608 6000 6001 6002 6003 6004 6005 6006 6200 6201 6202 6203 6204 6205 6206 6300 6301 6302 6303 6304 6305
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Specifically designed for applications where space limitations are a primary consideration and shafts are relatively large. Available with metal shields or Buna N seals. The 6000 series is capable of withstanding radial and thrust loads within the limitations of their ball complement. The conrad construction of the R series enables these bearings to take a thrust load as well as a radial load. The well designed ball complement and selection of retainers permit use of this series in high speed motor applications. This series is produced open, shielded or sealed. Shield and sealed bearings are made slightly wider as shown in the dimension table. Metric dimensions are in millimeters.
Item No.
PRB-11 PRB-12 PRB-13 PRB-14 PRB-15 PRB-16 PRB-17 PRB-18
Select "R" Series Double Sealed Inch
Double Shielded
Item No.
A
B
1
3
⁄8 3 ⁄16 1 ⁄4 3 ⁄8 1 ⁄2 5 ⁄8 3 ⁄4 1
Item No.
PRB-28 PRB-29 PRB-30 PRB-31 PRB-32 PRB-33 PRB-34 PRB-35 PRB-36
A
B
1
3
⁄8 ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ 1
⁄8 ⁄2 ⁄4 7 ⁄8 11⁄8 13⁄8 15⁄8 17⁄8 2
16 1 4 3 8 1 2 5 8 3 4 7 8
Pack Qty.
R2 R3 R4A R6 R8 R10 R12 R16
1 1 1 1 1 1 1 1
C
Bearing No.
Pack Qty.
⁄32 .196 9 ⁄32 9 ⁄32 5 ⁄16 11 ⁄32 7 ⁄16 1 ⁄2 1 ⁄2
99R2 99R3 99R4A 99R6 99R8 99R10 99R12 99R14 99R16
1 1 1 1 1 1 1 1 1
C
Bearing No.
Pack Qty.
77R2 77R3 77R4A 77R6 77R8 77R10 77R12 77R14 77R16
1 1 1 1 1 1 1 1 1
5
1
3
Bearing No.
⁄32 5 ⁄32 9 ⁄32 9 ⁄32 1 ⁄4 9 ⁄32 5 ⁄16 3 ⁄8
C 5
⁄8 1 ⁄2 3 ⁄4 7 ⁄8 11⁄8 13⁄8 15⁄8 2
3
Select "R" Series Double Shielded Inch Item No.
PRB-19 PRB-20 PRB-21 PRB-22 PRB-23 PRB-24 PRB-25 PRB-26 PRB-27
A
B
1
3
⁄8 ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ 1
5
⁄8 ⁄2 ⁄4 7 ⁄8 11⁄8 13⁄8 15⁄8 17⁄8 2
⁄32 .196 9 ⁄32 9 ⁄32 5 ⁄16 11 ⁄32 7 ⁄16 1 ⁄2 1 ⁄2
1
3
16 1 4 3 8 1 2 5 8 3 4 7 8
3
Stainless Steel Inch and Metric Item No.
Inch PRB-2 PRB-3 PRB-6 Metric PRB-7 PRB-8 PRB-9 PRB-10
880
A
B
C
Load Capacity Lbs.
Max. rpm No Load
Dynamic
Static
Bearing No.
Pack Qty.
⁄8 ⁄2 1
7 ⁄8 11⁄8 2
7
1
32 1 4 1 2
⁄ ⁄ ⁄
1,600 1,142 729
126 165 276
99 129 183
SS77R6 SS77R8 SS77R16
1 1 1
8 15 17 17
22 32 35 40
7 9 10 12
1,600 1,142 1,069 1,069
126 165 207 207
99 128 138 138
SS608 SS6002 SS6003 SS6203
1 1 1 1
3
BALL & TAPERED ROLLER BEARINGS Stainless Steel Bearings Inch and Metric
Plastic Bearings Inch and Metric C
A
B
C
These stainless steel bearings are semi-precision unground type. The 316 type stainless bearings are ideal for hostile environments and wash down applications where the load is too heavy for plastic bearings. Type 316 stainless is non-magnetic and can be run without lubrication at slow speeds. Type 316 stainless provides greater corrosion resistance over 440 type stainless. Cage is made of a polymer. Metric dimensions are in millimeters. Item No.
Inch NNB-60 NNB-62 NNB-63 NNB-64 NNB-66 NNB-67 NNB-68 NNB-69 Metric NNB-92 NNB-95 NNB-96 NNB-102
A
B
1
5
Load Capacity Lbs. Bearing Max. rpm Static Number No Load Dynamic
C
Pack Qty.
⁄4 ⁄8 ⁄8 1 ⁄2 1 ⁄2 5 ⁄8 3 ⁄4 1
⁄8 ⁄8 ⁄8 11⁄8 13⁄8 13⁄8 15⁄8 2
.196 7 ⁄32 9 ⁄32 1 ⁄4 7 ⁄16 7 ⁄16 5 ⁄16 1 ⁄2
2,352 1,600 1,600 1,142 1,069 1,069 840 729
89 126 126 165 207 207 234 276
51 99 99 129 138 138 156 183
R4 R6 R6A R8 R10B R10B R12 R16
1 1 1 1 1 1 1 1
8 15 17 17
22 32 35 40
7 9 10 12
1,600 1,142 1,069 1,069
126 165 207 207
99 129 138 138
608 6002 6003 6203
1 1 1 1
7
3
7
3
Double Sealed Double Row - Angular Contact Metric C
BA
A
B
These plastic bearings are corrosion resistant, lightweight and offer a great deal of design flexibility. The rings are delrin, ball retainer is chemical resistant polymer, and the balls are 316 stainless, providing a lube free operation where other bearings wouldn't hold up. Item No.
Inch NNB-01 NNB-02 NNB-03 NNB-04 NNB-05 NNB-06 NNB-07 NNB-08 NNB-09 NNB-11 NNB-13 NNB-14 NNB-15 NNB-16 NNB-17 Metric NNB-42 NNB-43 NNB-49 NNB-52
A
B 1
C
Load Capacity Lbs. Max. rpm No Load Dynamic Static
Bearing Number
Pack Qty.
16 1 4 1 4 1 4 3 8 3 8 1 2 5 8 1 2 3 8 1 2 5 8 3 4
⁄16 ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ 1
⁄2 ⁄8 ⁄8 3 ⁄4 3 ⁄4 7 ⁄8 7 ⁄8 11⁄8 11⁄8 11⁄8 13⁄8 13⁄8 13⁄8 15⁄8 2
5 ⁄32 .196 .196 7 ⁄32 9 ⁄32 7 ⁄32 9 ⁄32 1 ⁄4 1 ⁄4 3 ⁄8 7 ⁄16 7 ⁄16 7 ⁄16 5 ⁄16 1 ⁄2
3,167 2,352 2,352 2,352 2,352 1,600 1,600 1,142 1,142 1,142 1,069 1,069 1,069 840 729
17 26 26 26 26 42 42 55 55 55 69 69 69 78 92
11 17 17 17 17 33 33 43 43 43 46 46 46 52 61
R3 R3A R4 R4A R4AW R6 R6A R8 R8 R8A R10B R10B R10B R12 R16
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
8 10 10 17
22 26 30 40
7 8 9 12
1,600 1,600 1,142 840
42 42 55 78
33 33 43 52
608 6000 6200 6203
1 1 1 1
3
5
3
5
Tapered Roller Bearings Cup and Cone Sets Double row ball bearings are suitable for taking axial loads in both directions. Designed for use in pumps, motors, etc. All bearings are double sealed to keep dirt and other contaminants out. Load Capacity Lbs.
Item No.
A mm
B mm
C mm
Dynamic
Static
Bearing Number
Pack Qty.
INA-1155
12
32
15.9
2,390
1,320
32012RS
1
Tapered Roller Bearings Cup and Cone Sets
Set Basic Load Rating (Lbs.)
Speed Rating (rpm)
Item No.
Dynamic
Static
Grease
SKF-1S SKF-2S SKF-3S SKF-4S SKF-5S SKF-6S SKF-8S SKF-11S SKF-12S SKF-13S SKF-14S SKF-16S SKF-17S
4,770 6,180 8,600 5,850 10,300 7,550 5,850 6,300 6,180 7,420 5,850 6,180 7,420
4,680 6,300 8,540 6,740 12,400 8,990 7,310 7,350 6,970 9,670 6,740 6,970 9,670
9,000 8,500 8,000 7,500 5,600 6,300 7,000 8,000 8,000 6,000 7,500 8,000 6,000
Basic Load Rating (Lbs.)
Speed Rating (rpm)
Oil
Pack Qty.
Item No.
Dynamic
Static
Grease
Oil
Pack Qty.
13,000 12,000 11,000 10,000 7,500 8,500 9,500 11,000 11,000 8,000 10,000 11,000 8,000
1 1 1 1 1 1 1 1 1 1 1 1 1
PRB-221 PRB-222 PRB-223 PRB-224 PRB-225 PRB-226 PRB-227 PRB-228 PRB-229 PRB-230 PRB-231 PRB-232 PRB-233
4,770 6,180 8,600 5,850 10,300 7,550 5,850 6,300 6,180 7,420 5,850 6,180 7,420
4,680 6,300 8,540 6,740 11,400 8,990 7,310 7,350 6,970 9,670 6,740 6,970 9,670
9,000 8,500 8,000 7,500 5,600 6,300 7,000 8,000 8,000 6,000 7,500 8,000 6,000
13,000 12,000 11,000 10,000 7,500 8,500 9,500 11,000 11,000 8,000 10,000 11,000 8,000
1 1 1 1 1 1 1 1 1 1 1 1 1
881
HEAVY DUTY BEARINGS Precision ground on all contact surfaces. Recommended for applications requiring the accuracy of rotation and quiet performance of close tolerance precision grab bearings, and where superior seal is required to retain lubricant and keep the bearing free from dust and dirt. Double sealed bearings are greased packed as standard. Nylon cage design. Use for medium loads and for maximum speeds in the range of 6,000 rpm. ID and OD tolerance area is +.0000/-.0005". Width tolerance is +.000/-.005". Heavy Duty Precision Ground Radial Bearings
C B
r
G
d F D
A
J
A
H
Principal Dimensions
Item No.
+.0000 -.0005 Bore d (In.)
+.0000 -.0005 OD D (In.)
+.0000 -.0005 Outer Width B (In.)
SKF-9125* SKF-9130 SKF-9135* SKF-9140 SKF-9145* SKF-9150 SKF-9155*** SKF-9160** SKF-9165*** SKF-9170**
.500 .500 .625 .625 .750 .750 1.000 1.000 1.250 1.250
1.7500 1.7500 1.7500 1.7500 1.7500 1.7500 2.0000 2.0000 2.5625 2.5625
.625 .625 .625 .625 .625 .625 .625 .625 .750 .750
A (In.)
+.0000 -.0005 Inner Width C (In.)
.0625 .0625 .0625 .0625 .0625 .0625 .0625 .0625 .0625 .0625
.750 .750 .750 .750 .750 .750 .750 .750 .875 .875
Abutment and Fillet Dimensions
Basic Load Ratings
F (In.)
+.001 -.005 G (In.)
H (In.)
J (In.)
Radius (In.)
Weight (Lbs.)
Dynamic (Lbs.)
Static (Lbs.)
min (In.)
Max. (In.)
r Max. (In.)
Pack Qty.
1.009 1.009 1.009 1.009 1.009 1.009 1.306 1.306 1.675 1.675
.136 .136 .136 .136 .136 .136 .136 .136 .190 .190
.042 .042 .042 .042 .042 .042 .042 .042 .065 .065
1.9219 1.9219 1.9219 1.9219 1.9219 1.9219 2.1563 2.1563 2.7656 2.7656
.035 .035 .035 .035 .035 .035 .035 .035 .035 .035
.330 .330 .290 .290 .310 .310 .330 .330 .565 .565
2,595 2,595 2,595 2,595 2,595 2,595 2,970 2,970 5,360 5,360
1,010 1,010 1,010 1,010 1,010 1,010 1,350 1,350 2,620 2,620
.750 .750 .875 .875 1.000 1.000 1.250 1.250 1.500 1.500
1.500 1.500 1.500 1.500 1.500 1.500 1.750 1.750 2.312 2.312
.035 .035 .035 .035 .035 .035 .035 .035 .035 .035
1 1 1 1 1 1 1 1 1 1
*Snap ring in the groove **OD tolerance is +.0000/-.0006 ***Snap ring in the groove and OD tolerance is +.0000/-.0006 M
B
r
Heavy Duty Precision Ground Radial Bearings with Extended Inner Ring
G N
d F
D
J
L
A
H
K Principal Dimensions
Item No.
+.0000 -.0005 Bore d (In.)
+.0000 -.0005 OD D (In.)
+.0000 -.0005 Outer Width B (In.)
A (In.)
SKF-9175* SKF-9180 SKF-9185* SKF-9190 SKF-9195*** SKF-9200** SKF-9205*** SKF-9210**
.6250 .6250 .7500 .7500 1.0000 1.0000 1.2500 1.2500
1.7500 1.7500 1.7500 1.7500 2.0000 2.0000 2.5625 2.5625
.625 .625 .625 .625 .625 .625 .750 .750
.0625 .0625 .0625 .0625 .0625 .0625 .0625 .0625
F (In.)
+.005 -.005 G (In.)
H (In.)
1.009 1.009 1.009 1.009 1.306 1.306 1.672 1.672
.136 .136 .136 .136 .136 .136 .190 .190
.042 1.9219 .042 1.9219 .042 1.9219 .042 1.9219 .042 2.1563 .042 2.1563 .065 2.7656 .065 2.7656
J (In.)
Basic Load Ratings
+.0000 -.0005 Inner Width K (In.)
L (In.)
1.092 1.092 1.092 1.092 1.179 1.179 1.417 1.417
.405 .405 .405 .405 .492 .492 .605 .605
M (In.)
N (2 set screws)
Radius (In.)
Dynamic (Lbs.)
Static (Lbs.)
Weight (Lbs.)
Pack Qty.
.233 .233 .233 .233 .261 .261 .261 .261
10-32 10-32 10-32 10-32 10-32 10-32 1 ⁄4-28 1 ⁄4-28
.035 .035 .035 .035 .035 .035 .035 .035
2,595 2,595 2,595 2,595 2,970 2,970 5,360 5,360
1,010 1,010 1,010 1,010 1,350 1,350 2,620 2,620
.36 .36 .28 .28 .36 .36 .71 .71
1 1 1 1 1 1 1 1
*Snap ring in the groove **OD tolerance is +.0000/-.0006 ***Snap ring in the groove and OD tolerance is +.0000/-.0006
ER Bearings
Groove with (2) Lube Holes 180° Apart
B (2) Set Screws
H J
N at 120° Apart
Radius
A
Shaft Dia.
P
M
Item No.
RBC-330 RBC-340 RBC-350 RBC-360 RBC-370 RBC-380 RBC-390 RBC-400 RBC-410 RBC-420 RBC-430 RBC-440 RBC-450 RBC-460 RBC-470 RBC-480
882
Shaft Diameter 5
⁄8 5 ⁄8 3 ⁄4 3 ⁄4 1 1 3 1 ⁄16 13⁄16 11⁄4 11⁄4 17⁄16 17⁄16 11⁄2 11⁄2 115⁄16 115⁄16
+0.000 -0.005 OD A
Inner Width B
1.8504 1.8504 1.8504 1.8504 2.0472 2.0472 2.4409 2.4409 2.8346 2.8346 2.8346 2.8346 3.1496 3.1496 3.5433 3.5433
17⁄32 17⁄32 17⁄32 17⁄32 13⁄8 13⁄8 11⁄2 11⁄2 111⁄16 111⁄16 111⁄16 111⁄16 115⁄16 115⁄16 21⁄32 21⁄32
+0.000 -0.005 Outer Width M 5
⁄8 5 ⁄8 5 ⁄8 5 ⁄8 3 ⁄4 3 ⁄4 7 ⁄8 7 ⁄8 15 ⁄16 15 ⁄16 15 ⁄16 15 ⁄16 13⁄32 3 1 ⁄32 11⁄8 11⁄8
ER Series ball bearings, an industry standard, are used in demanding applications such as: cardboard/packing machinery, paper/printing machinery, carpet tufting machinery, general conveying equipment, pumps, blowers. These bearings feature exclusive heavy duty "DL" seals which are permanently sealed and prelubricated for long life. "DL" seals feature a steel trash guard combined with the inner ring labyrinth groove provide superior protection in wet/moist environments. These bearings come with two lubrication holes for regreasing, two knurled cup point set screws set 120 degrees apart offer excellent resistance to loosening under vibratory conditions. They are made of fully ground, SAE 52100 chrome alloy steel races featuring a black oxide finish for added corrosion resistance and are available with low-torque seals (SFR). Snap Ring
Location J 3
⁄32 3 ⁄32 3 ⁄32 3 ⁄32 3 ⁄32 3 ⁄32 1 ⁄8 1 ⁄8 1 ⁄8 1 ⁄8 1 ⁄8 1 ⁄8 1 ⁄8 1 ⁄8 1 ⁄8 1 ⁄8
Width H 3
⁄64 3 ⁄64 3 ⁄64 3 ⁄64 3 ⁄64 3 ⁄64 1 ⁄16 1 ⁄16 1 ⁄16 1 ⁄16 1 ⁄16 1 ⁄16 1 ⁄16 1 ⁄16 3 ⁄32 3 ⁄32
Basic Load Rating (Lbs.) Diameter P
N (2 set screws)
Radius
Dynamic
Static
Pack Qty.
21⁄16 21⁄16 21⁄16 21⁄16 217⁄64 217⁄64 221⁄32 221⁄32 35⁄64 35⁄64 35⁄64 35⁄64 313⁄32 313⁄32 325⁄32 325⁄32
10-32 10-32 10-32 10-32 1 ⁄4-28 1 ⁄4-28 1 ⁄4-28 1 ⁄4-28 1 ⁄4-28 1 ⁄4-28 1 ⁄4-28 1 ⁄4-28 5 ⁄16-24 5 ⁄16-24 3 ⁄8-24 3 ⁄8-24
0.04 0.04 0.04 0.04 0.04 0.04 0.04 0.04 0.04 0.04 0.04 0.04 0.062 0.062 0.062 0.062
2,860 2,860 2,860 2,860 3,145 3,145 4,360 4,360 5,755 5,755 5,755 5,755 6,535 6,535 7,900 7,900
1,480 1,480 1,480 1,480 1,770 1,770 2,535 2,535 3,450 3,450 3,450 3,450 4,025 4,025 5,250 5,250
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
THRUST BEARINGS Nylon Ball Retainers
B A E D
This new concept in thrust bearings provides superior performance and economical characteristics. The unique design of the molded nylon retainer captures the balls in precision molded pockets assuring smooth free turning and quiet operation. The nylon retainer is lightweight, provides natural lubricity and is corrosion resistant. Balls are precision grade 100 tolerance +/-.0001, +/-.0025mm. The thrust washers are hardened steel providing high strength to wear ratio for long life. Available with steel or stainless steel balls. Washers are included with bearing. Steel Item No.
TQ-012 TQ-018 TQ-025 TQ-031 TQ-037 TQ-043 TQ-050 TQ-056 TQ-062 TQ-068 TQ-075 TQ-081 TQ-087 TQ-093 TQ-100 TQ-112 TQ-125 TQ-150
Stainless
Load Rating Load Rating (Lbs.) (Lbs.) @ 15 rpm @ 5000 rpm
120 126 131 136 175 190 201 213 251 273 293 314 328 384 459 504 545 522
17 18 18 19 25 27 29 30 36 39 42 45 47 55 66 72 78 75
Item No.
TQS-012 TQS-018 TQS-025 TQS-031 TQS-037 TQS-043 TQS-050 TQS-056 TQS-062 TQS-068 TQS-075 TQS-081 TQS-087 TQS-093 TQS-100 TQS-112 TQS-125 TQS-150
Load Rating Load Rating (Lbs.) (Lbs.) Nominal ID @ 15 rpm @ 5000 rpm A
84 88 92 95 123 133 140 149 175 191 205 220 196 268 321 352 381 365
1
⁄8 ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ 1 11⁄8 11⁄4 11⁄2
12 12 12 13 17 19 20 21 25 27 29 31 33 38 46 50 54 52
3
16 1 4 5 16 3 8 7 16 1 2 9 16 5 8 11 16 3 4 13 16 7 8 15 16
Actual ID A
Nominal OD B
.128/.133 .191/.195 .253/.258 .316/.321 .378/.383 .441/.446 .503/.508 .566/.571 .628/.635 .691/.698 .753/.760 .816/.823 .878/.885 .941/.950 1.003/1.012 1.128/1.137 1.253/1.262 1.503/1.512
7
⁄ ⁄ ⁄16 5 ⁄8 13 ⁄16 7 ⁄8 15 ⁄16 1 11⁄8 13⁄16 11⁄4 15⁄16 13⁄8 19⁄16 15⁄8 13⁄4 17⁄8 21⁄8 16 1 2
9
Actual OD B
No. of Balls
Ball Size
D
E
Pack Qty.
.430/.437 .492/.499 .55/.562 .617/.624 .805/.812 .867/.874 .930/.937 .992/.999 1.115/1.124 1.178/1.187 1.240/1.249 1.303/1.312 1.365/1.374 1.551/1.562 1.613/1.624 1.738/1.749 1.863/1.874 2.113/2.124
6 7 8 9 6 7 8 9 6 7 8 9 10 9 10 12 14 14
.0938 .0938 .0938 .0938 .1250 .1250 .1250 .1250 .1563 .1563 .1563 .1563 .1563 .1875 .1875 .1875 .1875 .1875
.050 .050 .050 .050 .062 .062 .062 .062 .093 .093 .093 .093 .093 .125 .125 .125 .125 .125
.190/.196 .190/.196 .190/.196 .190/.196 .245/.253 .245/.253 .245/.253 .245/.253 .336/.348 .336/.348 .336/.348 .336/.348 .336/.348 .427/.447 .427/.447 .427/.447 .427/.447 .427/.447
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Note: Dimension D tolerance for .050 and .062 is +/- .003, .125 is +/-.005.
Cylindrical Rollers
C
B
A
Cylindrical roller thrust bearings have a comparatively large contact area between the roller and raceway. They can support greater loads and accommodate much more shock than ball thrust bearings of a similar size. Cylindrical roller thrust bearings are suitable for medium to heavy-duty applications with high thrust loads and low operating coefficient of friction requirements. The .032" thrust washer is punched from steel, through hardened and polished. These washers should be fully supported on their entire abutment surface. The .126" thrust washers are made from bearing steel. The raceways are ground while the bore and outside diameter are machined. Washers sold separately from bearings. Load Ratings Lbs. Item No.
INA-500 INA-505 INA-510 INA-515 INA-520 INA-525 INA-530 INA-535 INA-540 INA-545 INA-550
INA
TC815 TC1018 TC1220 TC1423 TC1427 TC1625 TC1828 TC2031 TC2435 TC2840 TC3244
A 1
⁄2 ⁄8 ⁄4 7 ⁄8 7 ⁄8 1 11⁄8 11⁄4 11⁄2 13⁄4 2 5 3
B 15
⁄16 11⁄8 11⁄4 17⁄16 111⁄16 19⁄16 13⁄4 115⁄16 23⁄16 21⁄2 23⁄4
C 5
⁄64 ⁄64 ⁄64 5 ⁄64 5 ⁄64 5 ⁄64 5 ⁄64 5 ⁄64 5 ⁄64 5 ⁄64 5 ⁄64 5 5
Static
Dynamic
Speed Limit (rpm)
5,300 6,600 8,000 10,500 18,600 12,100 16,300 20,500 23,700 30,000 32,500
1,920 2,170 2,410 2,900 4,400 3,150 3,850 4,500 4,850 5,600 5,800
13,000 11,000 9,500 8,500 7,500 7,500 6,500 6,000 5,000 4,500 4,000
.032" Washer
.126" Washer
Item No.
Item No.
Pack Qty.
INA-560 INA-565 INA-570 INA-575 INA-580 INA-585 INA-590 INA-595 INA-600 INA-605 INA-610
— — INA-625 INA-630 INA-635 INA-640 — INA-650 INA-655 INA-660 INA-665
1 1 1 1 1 1 1 1 1 1 1
Note: For oil lubrication use 25 percent of value with grease lubrication.
883
TURNTABLE & BALL BEARINGS Silverthin™ Bearings Type X Four Point Contact Brass Snapover Separator Standard
The Silverthin™ series are manufactured to industry standard sizes. The bearing widths and sections (distance from bore to outside diameter) in each series remain constant regardless of the change in bore diameter. Dynamic Load Capacity Item No.
Bore
OD
2 2 21⁄2 21⁄2 3 3 31⁄2 31⁄2 4 4 5 5 6 6 7 8
1
CCF-1100 CCF-1105 CCF-1110 CCF-1115 CCF-1120 CCF-1125 CCF-1130 CCF-1135 CCF-1140 CCF-1145 CCF-1150 CCF-1155 CCF-1160 CCF-1165 CCF-1170 CCF-1175
Width 1
2 ⁄2 25⁄8 3 31⁄8 31⁄2 35⁄8 4 41⁄8 41⁄2 45⁄8 51⁄2 55⁄8 61⁄2 65⁄8 71⁄2 85⁄8
⁄4 ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄
5
16 1 4 5 16 1 4 5 16 1 4 5 16 1 4 5 16 1 4 5 16 1 4 5 16 1 4 5 16
Static Load Capacity
Radial Lbs.
Thrust Lbs.
Moment Lbs.-In.
Radial Lbs.
Thrust Lbs.
Moment Lbs.-In.
Maximum rpm Radial, Thrust or Combined Load
323 458 363 521 413 589 453 634 486 690 569 794 634 899 693 1,071
794 1,135 912 1,297 1,014 1,442 1,118 1,598 1,213 1,721 1,403 1,981 1,572 2,220 1,735 2,670
367 521 506 730 667 963 846 1,217 1,035 1,495 1,462 2,103 1,968 2,804 2,515 4,441
682 930 830 1,149 994 1,343 1,144 1,546 1,293 1,751 1,597 2,158 1,906 2,567 2,204 3,370
1,711 2,344 2,097 2,840 2,475 3,355 2,856 3,862 3,227 4,379 3,988 5,386 4,740 6,404 5,507 8,434
772 1,083 1,154 1,603 1,603 2,221 2,139 2,946 2,748 3,770 4,186 5,729 5,936 8,082 7,988 14,025
1,500 1,500 1,200 1,200 833 1,000 714 714 625 625 500 500 333 416 285 250
Pack Qty.
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Note: For bearings with 1⁄4 inch widths, the maximum shaft or housing fillet radius that the bearing corners will clear is .025 inch. Bearings with 5⁄16 inch widths will clear .040 inch.
Turntable Bearings Lazy Susan
Lockable or Non-Lockable
BOLT TH’D HOLE (4x)
C
B
BOLT CLEARANCE HOLE (4x)
A B
Used for turntables and fixtures of all kinds. 5⁄16" thick. Has a full race of precision ground ball bearings for smooth gliding rotation. Pre-assembled. Bearing is interlocked for life time of unit. Zinc coated steel. 9" and 12" round bearings are available greased. Item No.
LS-3 LS-4 LS-6 LS-9 LS-9G* LS-12 LS-12G*
*Greased
884
Size
3 4 6 9 9 12 12
Shape
Square Square Square Round Round Round Round
Center Hole Dia. 1
1 ⁄4 25⁄32 411⁄16 41⁄2 41⁄2 69⁄32 69⁄32
Nominal Load Capacity (Lbs.)
Use With Turntables Approx. Dia.
Pack Qty.
200 300 500 750 750 1,000 1,000
Up to 18 12 to 25 15 to 30 17 to 35 17 to 35 Over 20 Over 20
1 1 1 1 1 1 1
Heavy duty turntables are ideal for swivel displays, welding tables, industrial assemblies and many other turntable applications. May be mounted using the recommended bolts or welded directly to the fixture. All sizes can be purchased as lockable or non-lockable units. Non-Locking Locking Item No.
Cast Iron SKF-80 SKF-81 SKF-82 SKF-83
Item No.
Load Cap. Lbs.
A Height
B Lgth.
C Center/ Center
SKF-85 SKF-86 SKF-87 SKF-88
1,000 2,500 5,000 10000
1.77 1.92 2.43 2.72
3.25 3.5 5 6.5
2.5 2.75 4 5.5
Mtg. Bolt Size 1
⁄4-20 ⁄4-20 ⁄8-16 3 ⁄8-16 1 3
Pack Qty.
1 1 1 1
BEARING ACCESSORIES Bearing Locknuts Steel Inch
B 50°
A
F C G H Peripheral Lock
Face Lock
Face Lock
Peripheral Lock
By applying torque to the locking screw, a pressfit or wave spring effect is created locking the female threads of the locknut to the male threads of the shaft. This deflection produces a strong mechanical metal to metal lock, but does not effect the squareness of the bearing face. The locking set screws do not protrude through the face or the threads of the locknut eliminating damage to the shaft or bearing. Locknuts are furnished with both spanner slots and holes. Made of low carbon steel. Face Lock Peripheral Lock Item No.
Item No.
A
B
BLN-03 BLN-04 BLN-05 BLN-06 BLN-07 BLN-08 BLN-09 BLN-10 — BLN-12
— BLN-04-PH BLN-05-PH BLN-06-PH — BLN-08-PH BLN-09-PH — BLN-11-PH —
1.125 1.375 1.562 1.750 2.062 2.250 2.531 2.688 2.968 3.156
.343 .375 .406 .406 .438 .438 .438 .500 .500 .531
C
Major Dia. F
Pitch Dia. G
Thread Pitch Dia. H
Pack Qty.
.938 1.125 1.281 1.500 1.812 2.000 2.281 2.438 2.656 2.844
.664 .781 .969 1.173 1.376 1.563 1.767 1.967 2.157 2.360
.6437/.6467 .7607/.7641 .9487/.9521 1.1369/1.1409 1.3399/1.3439 1.5269/1.5314 1.7309/1.7354 1.9309/1.9354 2.1209/2.1260 2.3239/2.3290
32 32 32 18 18 18 18 18 18 18
1 1 1 1 1 1 1 1 1 1
Locking Hexnuts Face and Peripheral Lock Inch
ADHESIVES, SEALANTS & TAPE
C
Pages 818 - 831
B
Face Lock
A
D No. of Slots Peripheral Lock
By applying torque to the locking screw, a press fit or wave spring effect is created locking the female threads of the locknut to the male threads of the shaft. Produces a strong metal to metal lock. The locking set screws do not protrude through the face of the threads of the locknut, eliminating damage to the shaft or other surface. Face Lock Peripheral Lock Item No.
Item No.
— — — — BLN-105 BLN-110 BLN-115 BLN-120
BLN-160 BLN-165 BLN-170 BLN-175 — BLN-185 — BLN-195
A 15
⁄16 1 11⁄8 11⁄4 17⁄16 15⁄8 17⁄8 21⁄4
C
D
Pack Qty.
⁄16-20 1 ⁄2-20 5 ⁄8-18 3 ⁄4-16 7 ⁄8-14 1-14 11⁄4-12 11⁄2-12
2 2 2 3 3 3 3 3
1 1 1 1 1 1 1 1
B
.340 .359 .359 .422 .484 .547 .719 .844
7
885
COLLARS & COUPLINGS Grip Fast™ Self-Locking Collars ABS and Stainless Steel Inch
Rigid Sleeve Couplings E
D
C
B A
These steel couplings provide a fixed union between two shafts which are precisely aligned. Slide collar on
Releases by pulling on outer ring and slide off
Automatically locks in position
Great for quick change over and quick adjustments, these self locking collars slide on in one direction and lock automatically. No tools are necessary for installation or removal. The ball bearings jam themselves between the inner metal ring and the shaft allowing up to 500 lbs. of axial holding power (based on cold rolled drawn steel). The outer body of the steel self locking collars is made of tough ABS plastic. The all stainless are made from Type 304 stainless steel. All collars are designed to fit shaft tolerances of +/-.020". Item No.
Bore Size
Steel w/ ABS Plastic Outer 3 SMI-187 ⁄16 1 SMI-250 ⁄4 5 SMI-312 ⁄16 3 SMI-375 ⁄8 1 SMI-500 ⁄2 9 SMI-562 ⁄16 5 SMI-620 ⁄8 3 SMI-750 ⁄4 7 SMI-875 ⁄8 SMI-1000 1 SMI-1062 11⁄16 SMI-1250 11⁄4 SMI-1500 11⁄2 SMI-2000 2 SMI-3000 3 All Stainless Steel 1 ⁄4 SMI-250SS 5 SMI-312SS ⁄16 3 SMI-375SS ⁄8 1 SMI-500SS ⁄2 3 SMI-750SS ⁄4
OD
Lgth. (Max.)
Pack Qty.
.558 .743 .743 1.107 1.107 1.400 1.400 1.400 1.860 1.860 1.860 2.165 2.165 2.725 3.775
.94 1.010 1.010 1.045 1.045 1.460 1.460 1.460 2.000 2.000 2.000 1.825 1.825 2.070 1.980
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
.750 .750 1.125 1.125 1.400
1.00 1.00 1.10 1.10 1.50
1 1 1 1 1
Item No.
+.000 -.010 A
+.001 -.000 B
+/-.010 C
D
+/-.015 E
Keyway Size
Pack Qty.
SC-250 SC-312 SC-375 SC-500 SC-625 SC-750 SC-875 SC-1000 SC-1125 SC-1250 SC-1375
.50 .63 .75 1.00 1.25 1.50 1.75 2.00 2.13 2.25 2.50
.250 .312 .375 .500 .625 .750 .875 1.000 1.125 1.250 1.375
.19 .25 .25 .38 .50 .50 .50 .75 .75 1.00 1.00
8-32 x 1⁄8 8-32 x 1⁄8 10-24 x 1⁄8 1 ⁄4-20 x 1⁄4 5 ⁄16-18 x 5⁄16 5 ⁄16-18 x 3⁄8 5 ⁄16-18 x 3⁄8 3 ⁄8-16 x 1⁄2 3 ⁄8-16 x 1⁄2 3 ⁄8-16 x 1⁄2 3 ⁄8-16 x 1⁄2
.75 1.00 1.00 1.50 2.00 2.00 2.00 3.00 3.00 4.00 4.50
None None None 1 ⁄8 x 1⁄16 3 ⁄16 x 3⁄32 3 ⁄16 x 3⁄32 3 ⁄16 x 3⁄32 1 ⁄4 x 1⁄8 1 ⁄4 x 1⁄8 1 ⁄4 x 1⁄8 5 ⁄16 x 5⁄32
1 1 1 1 1 1 1 1 1 1 1
Shaft Couplings Miniature Flexible Zero Backlash Jaw
B
A D
C
Regular
Clamp Style
TAPS & END MILLS
Taps Pages 470 - 474 End Mills Pages 500 - 508
Cap Screws Set for Clamp Inertia (In # Sec²) Stiffness Torque Screws Type
Item No. C D GU-3004, GU-3013, 0.866 0.551 6-32 GU-4001, GU-4013 GU-3101 - 3110, 1.18 0.787 8-32 GU-4101-4110 GU-3214 - 3219, 1.33 1.18 8-32 GT-4212 - 4219 GU-3318 - 3321, 2.6 1.57 10-24 GU04317 - 4321
1.7 x 10-6
127
20
5-40
8.8 x 10-6
279
54
6-32
5.3 x 10-5
1,014
130
8-32
3.5 x 10-4
3,042
174
Machined aluminum hubs with 92 durometer "spiders". Designed for fractional and sub-fractional motors. Absorbs parallel and angular misalignment. Excellent shock dampening and vibration isolation. Cross clamping available for positive shaft lock. Stiffness is in pounds per inch radian. All bores larger than 1⁄2" have a 3⁄16" x 5⁄32" keyway. Regular
Clamp Style
Item No.
Item No.
— GU-3004 GU-3101 GU-3105 GU-3013 GU-3107 GU-3108 GU-3109 GU-3110 — GU-3214 GU-3219 — GU-3318 GU-3319 GU-3320 GU-3321
886
4-40
GU-4001 — GU-4101 GU-4102 GU-4013 GU-4107 GU-4108 GU-4109 GU-4110 GU-4212 GU-4214 GU-4219 GU-4317 GU-4318 GU-4319 — GU-4321
Bore Size A 1
⁄8 ⁄8 ⁄16 3 ⁄16 1 ⁄4 1 ⁄4 5 ⁄16 5 ⁄16 3 ⁄8 3 ⁄8 3 ⁄8 1 ⁄2 1 ⁄2 1 ⁄2 5 ⁄8 5 ⁄8 3 ⁄4 1
3
Bore Size B 1
⁄8 ⁄4 ⁄16 1 ⁄4 1 ⁄4 3 ⁄8 5 ⁄16 3 ⁄8 3 ⁄8 3 ⁄8 1 ⁄2 1 ⁄2 5 ⁄8 3 ⁄4 5 ⁄8 3 ⁄4 3 ⁄4 1
3
Pack Qty.
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
SHAFT COUPLINGS Shaft Couplings Three Jaw Type
Keyway
Shaft Couplings Rigid Clamp Style
Overall Length
Setscrew
One Piece Bore
O.D.
Complete with keyway and set screw. No lubrication needed. Bored to +.001/-.000" tolerances. Must order two coupling halves and one insert of same out side diameter for complete coupling. Insert types include: Bost-Bronz inserts for high torque loads, particularly at slower speeds, rubber for quietness particularly at motor speeds, polyurethane for moderate to heavy shock loads. Coupling Inserts
Two Piece
Made of carbon steel. Available with or without a keyway. Clamp screws are forged and treated with an antivibration coating to keep them from loosening. w/Keyway
Bost-Bronz
Rubber
Polyurethane
Item No.
Item No.
Item No.
Outside Dia.
Pack Qty.
GE-217 GE-227 GE-237 GE-247
GE-218 GE-228 GE-238 GE-248
GE-219 GE-229 GE-239 GE-249
1.25 1.50 2.00 2.50
1 1 1 1
One Piece Two Piece
Coupling Halves
Item No.
Overall Length Boston
1.25" Outside Diameter GE-211 FC12 3/8 GE-213 FC12 1/2 1.50" Outside Diameter GE-221 FC15 1/2 GE-223 FC15 5/8 GE-224 FC15 3/4 GE-225 FC15 7/8 2.00" Outside Diameter GE-230 FC20 1/2 GE-232 FC20 5/8 GE-233 FC20 3/4 GE-234 FC20 7/8 GE-236 FC20-1 2.50" Outside Diameter GE-241 FC25 3/4 GE-242 FC25 7/8 GE-244 FC25 1 1/8 GE-246 FC25 1 1/4
Bore 3
⁄8 ⁄2
1
1
⁄2 5 ⁄8 3 ⁄4 7 ⁄8 1
Assembled
Unassembled
Pack Qty.
2.32 2.32
3.19 3.19
1 1
2.76 2.76 2.76 2.76
3.75 3.75 3.75 3.75
1 1 1 1
⁄2 ⁄8 3 ⁄4 7 ⁄8 1
3.69 3.69 3.69 3.69 3.69
4.81 4.81 4.81 4.81 4.81
1 1 1 1 1
3
4.13 4.13 4.13 4.13
5.38 5.38 5.38 5.38
1 1 1 1
5
⁄4 7 ⁄8 11⁄8 11⁄4
Note: Unassembled overall length is the dimension for assembly clearance.
Item No.
Item No.
Bore A
CC-103 — CC-105 — CC-107 — CC-110 CC-112 CC-115 CC-116 CC-119 CC-123
CC-403 CC-404 CC-405 CC-406 CC-407 CC-409 CC-410 CC-412 CC-415 CC-416 CC-419 CC-423
.375 .500 .500 .625 .625 .750 .750 .875 1.000 1.125 1.250 1.500
Keyway A 3
⁄32 1 ⁄8 1 ⁄8 3 ⁄16 3 ⁄16 3 ⁄16 3 ⁄16 3 ⁄16 1 ⁄4 1 ⁄4 1 ⁄4 3 ⁄8
Bore B
.375 .375 .500 .500 .625 .625 .750 .875 1.000 1.125 1.250 1.500
Keyway B 3
⁄32 3 ⁄32 1 ⁄8 1 ⁄8 3 ⁄16 3 ⁄16 3 ⁄16 3 ⁄16 1 ⁄4 1 ⁄4 1 ⁄4 3 ⁄8
Length
OD
Pack Qty.
7
13⁄8 13⁄4 13⁄4 2 2 21⁄4 21⁄4 21⁄2 3 31⁄8 31⁄4 37⁄8
⁄8 11⁄8 11⁄8 15⁄16 15⁄16 11⁄2 11⁄2 15⁄8 13⁄4 17⁄8 21⁄16 25⁄8
1 1 1 1 1 1 1 1 1 1 1 1
w/o Keyway One Piece Two Piece Item No.
CC-301 CC-302 CC-303 CC-304 CC-305 CC-306 CC-307 CC-309 CC-310 CC-312 CC-313 CC-315 CC-319 CC-323
Item No.
— — CC-503 CC-504 CC-505 — CC-507 — CC-510 — — CC-515 CC-519 CC-523
Bore A
.250 .375 .375 .500 .500 .625 .625 .750 .750 .875 1.000 1.000 1.250 1.500
Bore B
.250 .250 .375 .375 .500 .500 .625 .625 .750 .875 .500 1.000 1.250 1.500
Length
Pack Qty.
OD 5
1 13⁄8 13⁄8 13⁄4 13⁄4 2 2 21⁄4 21⁄4 21⁄2 3 3 31⁄4 37⁄8
⁄8 ⁄8 ⁄8 11⁄8 11⁄8 15⁄16 15⁄16 11⁄2 11⁄2 15⁄8 13⁄4 13⁄4 21⁄16 25⁄8
1 1 1 1 1 1 1 1 1 1 1 1 1 1
Length
Screw Size
7 7
Machinable Couplings Single Spit Black Oxide
Item No.
Machinable couplings provide an affordable alternative to expensive set-up costs and special machining. The single split style couplings come with a variety of standard bore sizes on one end, and a pilot hole on the other that can be rebored to any diameter less than the opposing bore.
CC-150 CC-151 CC-152 CC-153 CC-155 CC-156 CC-157 CC-158 CC-159
Bore 1
.500 .625 .750 .875 1.125 1.250 1.375 1.500 1.750
Bore 2
.235 .235 .235 .235 .360 .360 .360 .485 .485
OD
1.250 1.500 1.750 1.875 2.125 2.250 2.375 2.500 3.000
1.875 2.250 2.625 2.875 3.250 3.375 3.625 3.750 4.500
3
8-32 x ⁄8 10-32 x 1⁄2 1 ⁄4-28 x 5⁄8 1 ⁄4-28 x 5⁄8 1 ⁄4-28 x 5⁄8 1 ⁄4-28 x 5⁄8 1 ⁄4-28 x 5⁄8 1 ⁄4-28 x 5⁄8 5 ⁄16-24 x 7⁄8
Pack Qty.
1 1 1 1 1 1 1 1 1
887
GEARS & RACKS Spur Gear Racks
Pitch Line To Back (B)
Face Width 1 ⁄8 - 3⁄4 7 ⁄8 - 11⁄2 13⁄4 - 2
Width A Overall Thickness
Length
Tolerances +.000/-.002 +.000/-.003 +.000/-.004
141⁄2 degree pressure angle gearing racks. All are steel. Ends are not machined. Length tolerances are +1.000/-.000" to allow for cutting and matching.
Used with gears below. Item No.
Boston
Pitch
Width
Lgth. Feet
A
B
Pack Qty.
Item No.
Boston
Pitch
Width
Lgth. Feet
A
B
Pack Qty.
GE-3200 GE-2400 GE-2000 GE-2001 GE-1600 GE-1601 GE-1200 GE-1202
L503-4 L505-4 L509-4 L509-6 L512-4 L512-6 L514-4 L515-4
32 24 20 20 16 16 12 12
.188 .250 .375 .375 .500 .500 .750 .750
4 4 4 6 4 6 4 4
.188 .250 .375 .375 .500 .500 .500 .750
.156 .208 .325 .325 .438 .438 .417 .667
1 1 1 1 1 1 1 1
GE-1203 GE-1000 GE-1001 GE-1002 GE-0800 GE-0802 GE-0600
L515-6 L516-4 L516-6 L517-4 L518-4 L519-4 L520-4
12 10 10 10 8 8 6
.750 1.000 1.000 1.000 1.250 1.250 1.500
6 4 6 4 4 4 4
.750 .625 .625 1.000 .750 1.250 1.000
.667 .525 .525 .900 .625 1.125 .833
1 1 1 1 1 1 1
Miter Gears
C
Mounting Distance
B A D
F
Hub Proj.
Bore E
Item No.
GE-110 GE-111 GE-112 GE-125 GE-101 GE-127 GE-102 GE-119
Boston Pitch
L110Y L111Y L112Y L125Y L101Y L127Y L102Y L119Y
16 16 16 12 12 12 12 12
No. of Pitch Dia. Teeth A Bore
16 20 24 15 15 18 18 21
1.00 1.25 1.50 1.25 1.25 1.50 1.50 1.75
.3750 .4375 .5000 .3750 .5000 .5000 .6250 .5000
B
C
D
E
F
Pack Qty.
.23 .28 .32 .29 .29 .33 .33 .40
1.062 1.250 1.375 1.250 1.250 1.500 1.500 1.750
.755 .849 .880 .864 .864 1.021 1.021 1.192
.75 1.00 1.00 1.00 1.00 1.25 1.25 1.38
.44 .50 .50 .50 .50 .63 .63 .69
1 1 1 1 1 1 1 1
20 degree pressure angle for transmitting motion and power between intersecting shafts at right angles. All are unhardened steel. 1:1 ratio applications. Coniflex tooth form allows for minor adjustments and increases gear life. Bore tolerance is +/-.0005". Item No.
Boston
GE-113 L113Y GE-128 L128Y GE-129 L129Y GE-103 L103Y GE-130 L130Y GE-131 L131Y GE-115 L115Y GE-105 L105Y-A
No. of Pitch Dia. Pitch Teeth A
12 10 10 10 10 10 8 8
24 20 20 20 25 25 24 24
2.00 2.00 2.00 2.00 2.50 2.50 3.00 3.00
Bore
B
C
D
.5000 .5000 .6250 .7500 .7500 1.0000 .7500 1.0000
.44 .45 .45 .45 .56 .56 .66 .68
1.875 2.000 2.000 2.000 2.438 2.438 2.562 2.750
1.224 1.364 1.364 1.364 1.630 1.630 1.583 1.786
E
F
Pack Qty.
1.31 .69 1.62 .81 1.62 .81 1.62 .81 2.00 .94 2.00 .94 1.75 .81 2.50 1.00
1 1 1 1 1 1 1 1
Spur Gears
B C
A
D
Used with gear racks above. Item No.
GE-3216 GE-3218 GE-3220 GE-3224 GE-3240 GE-2412 GE-2416 GE-2420 GE-2424 GE-2012 GE-2016 GE-2020 GE-2024 GE-2032 GE-2048 GE-1612 GE-1614 GE-1616 GE-1620 GE-1624 GE-1632 GE-1640
888
Boston Pitch
H3216 H3218 H3220 H3224 H3240 H2412 H2416 H2420 H2424 NA12B NA16B NA20B NA24 NA32 NA48A NB12 NB14B NB16B NB20B NB24B NB32 NB40A
32 32 32 32 32 24 24 24 24 20 20 20 20 20 20 16 16 16 16 16 16 16
141⁄2 degree pressure angle gearing for transmitting motion and power between parallel shafts. All are steel except GE-1040, 1048 and 1248 which are cast iron. 32 and 24 pitch spur gears include a set screw. None include key ways. Bore tolerance is +/- .0005". Diameter tolerance is +/-1/32".
Bore E
No. of Teeth
Pitch Dia. A
Bore
B
C
D
E
OD
Pack Qty.
Item No.
Boston
Pitch
No. of Teeth
Pitch Dia. A
Bore
B
C
D
E
OD
Pack Qty.
16 18 20 24 40 12 16 20 24 12 16 20 24 32 48 12 14 16 20 24 32 40
.500 .562 .625 .750 1.250 .500 .667 .833 1.000 .600 .800 1.000 1.200 1.600 2.400 .750 .875 1.000 1.250 1.500 2.000 2.500
.1875 .1875 .2500 .3125 .3750 .2500 .3125 .3125 .3750 .3125 .3750 .3750 .3750 .3750 .3750 .3750 .3750 .5000 .5000 .5000 .5000 .5000
.188 .188 .188 .188 .188 .250 .250 .250 .250 .375 .375 .375 .375 .375 .375 .500 .500 .500 .500 .500 .500 .500
.31 .31 .31 .31 .38 .31 .31 .31 .38 .38 .38 .38 .38 .50 .50 .44 .44 .44 .44 .44 .50 .50
.498 .498 .498 .500 .568 .560 .560 .562 .630 .755 .755 .755 .755 .875 .875 .940 .940 .940 .940 .940 1.000 1.000
.39 .45 .52 .64 .88 .36 .54 .70 .87 .46 .66 .84 .92 1.32 1.33 .56 .69 .81 .96 1.20 1.70 1.69
.562 .624 .687 .812 1.312 .583 .750 .916 1.083 .700 .900 1.100 1.300 1.700 2.500 .875 1.000 1.125 1.375 1.625 2.125 2.625
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
GE-1648 GE-1212 GE-1216 GE-1218 GE-1224 GE-1230 GE-1232 GE-1248 GE-1012 GE-1018 GE-1020 GE-1024 GE-1030 GE-1040 GE-1048 GE-0812 GE-0816 GE-0820 GE-0824 GE-0612 GE-0624
NB48A ND12 ND16 ND18 ND24 ND30 ND32A ND48 NF12 NF18 NF20 NF24 NF30A NF40 NF48 NH12 NH16 NH20 NH24A NJ12 NJ24A
16 12 12 12 12 12 12 12 10 10 10 10 10 10 10 8 8 8 8 6 6
48 12 16 18 24 30 32 48 12 18 20 24 30 40 48 12 16 20 24 12 24
3.000 1.000 1.333 1.500 2.000 2.500 2.667 4.000 1.200 1.800 2.000 2.400 3.000 4.000 4.800 1.500 2.000 2.500 3.000 2.000 4.000
.5000 .5000 .6250 .6250 .6250 .6250 .6250 .7500 .6250 .7500 .7500 .7500 .7500 .8750 .8750 .7500 .8750 .8750 .8750 1.0000 1.1250
.500 .750 .750 .750 .750 .750 .750 .750 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.250 1.250 1.250 1.250 1.500 1.500
.50 .50 .50 .50 .50 .62 .62 .75 .62 .62 .62 .62 .88 .88 .88 .75 .75 .75 .88 .88 .88
1.000 1.250 1.250 1.250 1.250 1.370 1.370 1.500 1.620 1.620 1.620 1.620 1.880 1.880 1.880 2.000 2.000 2.000 2.130 2.380 2.380
2.19 .75 .99 1.15 1.65 2.15 1.92 1.75 .92 1.42 1.62 2.02 2.02 2.12 2.12 1.12 1.56 2.06 2.06 1.46 3.00
3.125 1.167 1.500 1.667 2.167 2.667 2.834 4.167 1.400 2.000 2.200 2.600 3.200 4.200 5.000 1.750 2.250 2.750 3.250 2.333 4.333
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
FLEXIBLE SHAFT COUPLINGS M-Style
Gear Grip E
G
E B .125 min.
K B
D
B D
bore H
sleeve O.D.
E
Type M-14 M-24 M-28 M-32 M-38
Nominal Torque 86 86 390 520 694
Maximum Torque 173 347 781 1,041 1,388
Nominal HP @ 1750 @ 1140 RPM RPM 2.5 1.5 4.5 3.2 10.5 7 14.5 9.5 22.1 12.5
S
H A
L
C
L
Max. RPM 14,000 10,600 8,500 7,500 6,700
A
Bore In. Min/Max. .187/.551 .375/.945 .250/1.125 .437/1.26 .437/1.50
Nylon sleeve and steel hubs allow high ambient temperature operation without lubrication, or maintenance. Continuous operating ambients of 180 degrees Fahrenheit with peak temperatures to 250 degrees Fahrenheit. Nylon sleeves resistant to dirt, moisture, most chemicals and petroleum products. Double crowned tooth design provides free axial movement. Low friction and minimum stress during misalignment. No bolts, pins, flanges or protrusions to affect balance or safety. Blind assembly with slip together components for easy inspection and adjustment without disassembly. Available with no bore (except centering pilot hole), bores and bores with keyways.
Neoprene and urethane rubber sleeve compounds provide excellent torsional vibration dampening, absorb load pulsations and minimize drive line shock. The load is distributed evenly over a wide splined contact area. Gear grip couplings handle shock, minimize assembly time, require no special tools and allow for “blind” assembly. Not affected by moisture, dirt and abrasives. No lubrication, adjustments or maintenance is required. Provides protection to the expensive drive train during extreme overload, jamming or high shock. Electrical isolation. No possibility of metalto-metal contact under severe overload, wear or coupling failure. Parallel misalignment to .040 inches, except Type A, which is .016 inches. Angular misalignment to 7.5 degree maximum. For complete coupling, order two hubs and one sleeve of the same size. Sleeves
For complete coupling, order two hubs and one nylon sleeve of the same type. Nylon Sleeves Urethane
See pages 886-887 for other shaft couplings. Item No.
Type
No. of Teeth
Pack Qty.
GU-400 GU-401 GU-402 GU-403 GU-404 GU-405
M-14 M-19 M-24 M-28 M-32 M-38
20 24 28 34 40 44
1 1 1 1 1 1
Item No.
Material
Size
B
D
GU-1000 GU-1001 GU-1002 GU-1003 GU-1004 GU-1005 GU-1006 GU-1007* GU-1008 GU-1009 GU-1011
Neoprene Urethane Neoprene Urethane Neoprene Urethane Neoprene Neoprene Neoprene Urethane Urethane
A A B B C C D D E E F
.56 .56 .85 .85 1.59 1.59 1.59 1.59 1.59 1.59 1.59
.78 .80 1.20 1.14 1.20 1.14 1.40 1.56 1.84 1.82 2.37
Neoprene
Nominal Max. Torque Torque HP @ Inch/ Inch/ 1750 Lbs. Lbs. rpm
4 13 16 40 30 50 60 72 108 185 200
18 55 65 160 110 200 250 400 440 738 800
.11 .36 .44 1.10 .83 1.30 1.70 2.00 3.00 5.00 5.50
Max. Stiffness Speed in # Pack rpm (Rad) Qty.
25,000 25,000 16,800 16,800 16,500 16,500 15,500 15,500 15,000 15,000 10,000
28 57 124 183 107 115 270 225 630 423 1,530
1 1 1 1 1 1 1 1 1 1 1
Bore
Keyseat
Pack Qty.
— — — — — — — — — — — 1 ⁄8 x 1⁄16 1 ⁄8 x 1⁄16 3 ⁄16 x 3⁄32 1 ⁄8 x 1⁄16 1 ⁄8 x 1⁄16 3 ⁄16 x 3⁄32 3 ⁄16 x 3⁄32 3 ⁄16 x 3⁄32 3 ⁄16 x 3⁄32 1 ⁄4 x 1⁄8
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
*Reinforced Note: One angular degree of twist = .01745 radians.
Note: Torque in inch pounds. Nominal torque allows fro 180 degrees F ambient, full misalignment and/or maximum RPM.
Hubs
Hubs
Item No.
Item No.
Type
A
B
D
Hubs with No Bore GU-100 M-14 1.77 1.00 1.57 GU-101 M-19 1.96 1.25 1.90 GU-105 M-38 3.15 2.30 3.25 Hubs with Bore & Keyway GU-201 M-14 1.77 1.00 1.57 GU-202 M-14 1.77 1.00 1.57 GU-204 M-19 1.96 1.25 1.90 GU-205 M-19 1.96 1.25 1.90 GU-206 M-24 2.07 1.42 2.05 GU-207 M-24 2.07 1.42 2.05 GU-208 M-24 2.07 1.42 2.05 GU-211 M-28 3.17 1.75 2.58 GU-212 M-28 3.17 1.75 2.58 GU-213 M-28 3.17 1.75 2.58 GU-214 M-28 3.17 1.75 2.58
E
G
H
K
L
.14 1.45 .19 1.30 .78 .25 1.45 .28 1.53 .86 .65 1.90 .35 2.70 1.40 .14 .14 .25 .25 .25 .25 .25 .69 .69 .69 .69
1.45 1.45 1.45 1.45 1.60 1.60 1.60 1.80 1.80 1.80 1.80
.19 .19 .28 .28 .39 .39 .39 .37 .37 .37 .37
1.30 1.30 1.53 1.53 1.76 1.76 1.76 2.12 2.12 2.12 2.12
.78 .78 .86 .86 .84 .84 .84 1.40 1.40 1.40 1.40
Set Pack Screws Bore Keyseat Qty.
— — — 10-24 10-24 1 ⁄4-20 1 ⁄4-20 1 ⁄4-20 1 ⁄4-20 1 ⁄4-20 1 ⁄4-20 1 ⁄4-20 1 ⁄4-20 1 ⁄4-20
— — — 1
⁄2 ⁄8 ⁄8 3 ⁄4 1 ⁄2 5 ⁄8 3 ⁄4 5 ⁄8 3 ⁄4 7 ⁄8 11⁄8
— — —
1 1 1
⁄8 x 1⁄16 ⁄16 x 3⁄32 ⁄16 x 3⁄32 3 ⁄16 x 3⁄32 1 ⁄8 x 1⁄16 3 ⁄16 x 3⁄32 3 ⁄16 x 3⁄32 3 ⁄16 x 3⁄32 3 ⁄16 x 3⁄32 3 ⁄16 x 3⁄32 1 ⁄4 x 1⁄8
1 1 1 1 1 1 1 1 1 1 1
1
5
3
5
3
Size
Hubs with Bore GU-2101 A GU-2102 A GU-2103 A GU-2104 A GU-2105 A GU-2201 B GU-2202 B GU-2203 B GU-2205 B GU-2302 C GU-2304 C GU-2401 D GU-2403 D GU-2404 D GU-2501 E GU-2503 E GU-2504 E GU-2505 E GU-2602 F GU-2603 F GU-2605 F
A
C
H
S
1.00 1.00 1.00 1.00 1.00 1.50 1.50 1.50 1.50 2.25 2.25 2.38 2.38 2.38 2.38 2.38 2.38 2.38 2.50 2.50 2.50
.50 .50 .50 .50 .50 .72 .72 .72 .72 1.09 1.09 1.14 1.14 1.14 1.14 1.14 1.14 1.14 1.19 1.19 1.19
.70 .70 .70 .70 .70 1.15 1.15 1.15 1.15 1.15 1.15 1.45 1.45 1.45 1.63 1.63 1.63 1.63 2.06 2.06 2.06
.22 .22 .22 .22 .22 .33 .33 .33 .33 .33 .33 .38 .38 .38 .38 .38 .38 .38 .43 .43 .43
E No. of Set Teeth Screws
8 8 8 8 8 8 8 8 8 8 8 10 10 10 12 12 12 12 12 12 12
8-32 8-32 8-32 8-32 8-32 1 ⁄4-20 1 ⁄4-20 1 ⁄4-20 1 ⁄4-20 1 ⁄4-20 1 ⁄4-20 1 ⁄4-20 1 ⁄4-20 1 ⁄4-20 1 ⁄4-20 1 ⁄4-20 1 ⁄4-20 1 ⁄4-20 5 ⁄16-18 5 ⁄16-18 5 ⁄16-18
1
⁄8 ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ 1
3
16 1 4 5 16 3 8 1 4 5 16 3 8 1 2 3 8 1 2 3 8 1 2 5 8 3 8 1 2 5 8 3 4 3 4 7 8
889
SHAFT COLLARS These collars offer full radial holding power without marring the shaft. Two piece design allows for installation without disassembling equipment. Metric dimensions are shown in millimeters. Shaft Collars One and Two Piece Inch Steel - Stainless Steel - Aluminum One-Piece Two-Piece Item No.
Steel CTC-2 CTC-4 CTC-6 CTC-8 CTC-10 CTC-12 CTC-14 CTC-16 CTC-18 CTC-20 CTC-22 CTC-24 CTC-26 CTC-28 CTC-30 CTC-32 CTC-34 CTC-36 CTC-38 CTC-40 CTC-42 CTC-44 CTC-46 CTC-48 CTC-50 CTC-52 CTC-54 — CTC-58 CTC-60 CTC-62 CTC-64 CTC-66 CTC-68 CTC-70 CTC-72 CTC-74 — — CTC-78 — CTC-80 CTC-82 CTC-84 — CTC-88
One Piece
Two Piece
D Clamp SCREW
A
C
B
Item No.
A
1 — ⁄2 CTC-104 5⁄8 11 CTC-106 ⁄16 CTC-108 11⁄16 CTC-110 7⁄8 CTC-112 15⁄16 CTC-114 11⁄8 CTC-116 11⁄4 CTC-118 15⁄16 CTC-120 13⁄8 CTC-122 11⁄2 CTC-124 15⁄8 CTC-126 15⁄8 CTC-128 13⁄4 CTC-130 13⁄4 CTC-132 17⁄8 CTC-134 17⁄8 CTC-136 21⁄16 CTC-138 21⁄16 CTC-140 21⁄8 CTC-142 21⁄4 CTC-144 21⁄4 CTC-146 23⁄8 CTC-148 23⁄8 CTC-150 25⁄8 CTC-152 23⁄4 CTC-154 23⁄4 CTC-155 27⁄8 CTC-158 27⁄8 CTC-160 3 CTC-162 3 CTC-164 31⁄4 CTC-166 31⁄4 CTC-168 31⁄4 CTC-170 31⁄2 CTC-172 31⁄2 CTC-174 33⁄4 CTC-176 37⁄8 CTC-177 4 CTC-178 4 CTC-179 41⁄4 CTC-180 41⁄4 CTC-182 41⁄4 CTC-184 41⁄4 CTC-185 41⁄2 CTC-188 43⁄4
B 1
⁄8 ⁄16 1 ⁄4 5 ⁄16 3 ⁄8 7 ⁄16 1 ⁄2 9 ⁄16 5 ⁄8 11 ⁄16 3 ⁄4 13 ⁄16 7 ⁄8 15 ⁄16 1 11⁄16 11⁄8 13⁄16 11⁄4 15⁄16 13⁄8 17⁄16 11⁄2 19⁄16 15⁄8 111⁄16 13⁄4 113⁄16 17⁄8 115⁄16 2 21⁄8 23⁄16 21⁄4 23⁄8 27⁄16 21⁄2 25⁄8 211⁄16 23⁄4 213⁄16 27⁄8 215⁄16 3 33⁄16 37⁄16 3
C
Clamp Screw Pack D Qty.
1
⁄4 4-40 ⁄16 4-40 5 ⁄16 4-40 5 ⁄16 4-40 11 ⁄32 6-32 3 ⁄8 6-32 13 ⁄32 8-32 7 ⁄16 10-32 7 ⁄16 10-32 7 ⁄16 10-32 1 ⁄2 1⁄4-28 1 ⁄2 1⁄4-28 1 ⁄2 1⁄4-28 1 ⁄2 1⁄4-28 1 ⁄2 1⁄4-28 1 ⁄2 1⁄4-28 1 ⁄2 1⁄4-28 1 ⁄2 1⁄4-28 1 ⁄2 1⁄4-28 9 ⁄16 1⁄4-28 9 ⁄16 1⁄4-28 9 ⁄16 1⁄4-28 9 ⁄16 1⁄4-28 9 ⁄16 1⁄4-28 11 ⁄16 5⁄16-24 11 ⁄16 5⁄16-24 11 ⁄16 5⁄16-24 11 ⁄16 5⁄16-24 11 ⁄16 5⁄16-24 11 ⁄16 5⁄16-24 11 ⁄16 5⁄16-24 3 ⁄4 5⁄16-24 3 ⁄4 5⁄16-24 3 ⁄4 5⁄16-24 3 ⁄4 5⁄16-24 3 ⁄4 5⁄16-24 7 ⁄8 3⁄8-24 7 ⁄8 3⁄8-24 7 ⁄8 3⁄8-24 7 ⁄8 3⁄8-24 7 ⁄8 3⁄8-24 7 ⁄8 3⁄8-24 7 ⁄8 3⁄8-24 7 ⁄8 3⁄8-24 7 ⁄8 3⁄8-24 7 ⁄8 3⁄8-24 5
One-Piece
Two-Piece
Item No.
Item No.
A
Stainless Steel CTC-2SS — CTC-4SS — CTC-6SS CTC-106SS CTC-8SS — CTC-10SS CTC-110SS CTC-12SS CTC-112SS — CTC-114SS — CTC-116SS — CTC-118SS CTC-19SS — CTC-22SS CTC-122SS CTC-26SS CTC-126SS — CTC-127SS CTC-30SS CTC-130SS — CTC-131SS CTC-34SS CTC-134SS CTC-38SS CTC-138SS — CTC-139SS — CTC-142SS CTC-46SS CTC-146SS CTC-62SS CTC-162SS Aluminum CTC-6A — CTC-10A CTC-110A CTC-12A — CTC-14A CTC-114A CTC-18A CTC-118A CTC-22A CTC-122A CTC-26A CTC-126A CTC-30A CTC-130A — CTC-131A CTC-32A CTC-132A CTC-33A — CTC-38A CTC-138A CTC-39A — CTC-40A — CTC-46A CTC-146A CTC-48A — CTC-54A CTC-154A CTC-62A CTC-162A
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
B 1
1
⁄2 ⁄8 ⁄16 11 ⁄16 7 ⁄8 15 ⁄16 11⁄8 11⁄4 15⁄16 13⁄8 11⁄2 15⁄8 13⁄4 13⁄4 17⁄8 17⁄8 21⁄16 21⁄8 21⁄4 23⁄8 3
⁄8 ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ 1 11⁄16 11⁄8 11⁄4 15⁄16 13⁄8 11⁄2 2
11
⁄4 ⁄8 ⁄16 1 ⁄2 5 ⁄8 3 ⁄4 7 ⁄8 1 11⁄16 11⁄8 13⁄16 11⁄4 15⁄16 13⁄8 11⁄2 15⁄8 13⁄4 2
1
3
5
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
5 16 11 32 3 8 13 32 7 16 1 2 1 2 1 2 1 2 1 2 1 2 1 2 9 16 9 16 9 16 11 16 11 16 11 16
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
5
1
⁄16 ⁄8 ⁄16 11⁄8 15⁄16 11⁄2 15⁄8 13⁄4 17⁄8 17⁄8 21⁄16 21⁄16 21⁄8 21⁄4 23⁄8 25⁄8 23⁄4 3
⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄
3
7
7
15
⁄4 4-40 ⁄16 4-40 ⁄16 4-40 5 ⁄16 4-40 11 ⁄32 6-32 3 ⁄8 6-32 13 ⁄32 8-32 7 ⁄16 10-32 7 ⁄16 10-32 7 ⁄16 10-32 1 ⁄2 1⁄4-28 1 ⁄2 1⁄4-28 1 ⁄2 1⁄4-28 1 ⁄2 1⁄4-28 1 ⁄2 1⁄4-28 1 ⁄2 1⁄4-28 1 ⁄2 1⁄4-28 9 ⁄16 1⁄4-28 9 ⁄16 1⁄4-28 9 ⁄16 1⁄4-28 11 ⁄16 5⁄16-24 5
16 1 4 5 16 3 8 7 16 1 2 9 16 5 8 11 16 3 4 7 8 15 16
11
Clamp Screw Pack D Qty.
C
4-40 6-32 6-32 8-32 10-32 1 ⁄4-28 1 ⁄4-28 1 ⁄4-28 1 ⁄4-28 1 ⁄4-28 1 ⁄4-28 1 ⁄4-28 1 ⁄4-28 1 ⁄4-28 1 ⁄4-28 5 ⁄16-24 5 ⁄16-24 5 ⁄16-24
One and Two Piece Metric Steel
One-Piece Two-Piece
One Piece
Two Piece
D Clamp SCREW
A
C
B
Item No.
Item No.
A
B
CTC-701 CTC-702 CTC-703 CTC-704 CTC-705 CTC-706 CTC-707 CTC-708 CTC-710 CTC-709 CTC-711 CTC-712
CTC-801 CTC-802 CTC-803 CTC-804 CTC-805 CTC-806 CTC-807 CTC-808 CTC-810 CTC-809 CTC-811 CTC-812
16 16 18 24 24 28 34 34 36 38 40 45
5 6 8 9 10 12 15 16 18 17 20 25
One-Piece Two-Piece
C
Clamp Screw D
Pack Qty.
Item No.
9 9 9 9 9 11 13 13 13 13 15 15
M3 x 8 M3 x 8 M3 x 8 M3 x 10 M3 x 10 M4 x 12 M5 x 16 M5 x 16 M5 x 16 M5 x 16 M6 x 16 M6 x 16
1 1 1 1 1 1 1 1 1 1 1 1
CTC-713 CTC-714 CTC-715 CTC-716 CTC-717 CTC-718 CTC-719 CTC-720 CTC-721 CTC-722 CTC-723
Item No.
A
CTC-813 54 CTC-814 57 CTC-815 60 CTC-816 73 CTC-817 78 CTC-818 82 CTC-819 88 CTC-820 93 CTC-821 98 CTC-822 103 CTC-823 108
B
C
30 35 40 45 50 55 60 65 70 75 80
15 15 15 19 19 19 19 19 19 19 19
Clamp Screw D
M6 M6 M6 M6 M8 M8 M8 M8 M8 M8 M8
x x x x x x x x x x x
18 18 18 18 25 25 25 25 25 25 25
Hinged Shaft Collars Steel Hinged construction and a captive clamp screw to simplify assembly. These fully split collars eliminate lost screws and downtime. Hinged collars provide the same axial load handling capabilities as our two piece collars. Both halves are machined from the same stock and then joined together by a heattreated triple-link hinge. These collars have a smooth ID, OD, and sides with no protruding pins or screws. All steel shaft collars are made of 12L14 or mild steel with black finish.
890
Item No.
Bore Size
OD
Width
Screw
Pack Qty.
CTC-401 CTC-402 CTC-403 CTC-404 CTC-405 CTC-406 CTC-408 CTC-409 CTC-410 CTC-411 CTC-412 CTC-413 CTC-415 CTC-416
.500 .625 .750 .875 1.000 1.125 1.250 1.375 1.500 1.625 1.750 2.000 2.500 3.000
1.250 1.500 1.750 1.875 2.000 2.125 2.250 2.375 2.500 2.750 3.000 3.250 4.000 4.500
.375 .438 .500 .500 .500 .500 .500 .500 .500 .625 .625 .625 .750 .750
8-32 10-32 1 ⁄4-28 1 ⁄4-28 1 ⁄4-28 1 ⁄4-28 1 ⁄4-28 1 ⁄4-28 1 ⁄4-28 5 ⁄16-24 5 ⁄16-24 5 ⁄16-24 3 ⁄8-24 3 ⁄8-24
1 1 1 1 1 1 1 1 1 1 1 1 1 1
Pack Qty.
1 1 1 1 1 1 1 1 1 1 1
SHAFTING, COLLARS & ACCESSORIES Shaft Collars One Piece Inch Steel and Stainless Steel
Keyed Shafting Three and Six Foot Lengths Cold Drawn Steel
Stamped style are stamped, galvannealed. Tolerance on ID for LSC-2E and LSC-3E is +.004/-000".
D SET SCREW
Item No.
A
Available in three foot and six foot lengths. C1018 cold drawn steel. Outside diameters are +.000/-.002". Keyways are +.016/.000" on depth and +.002/-.000" on width. Keyways are cut full length of each bar and are in accordance with ANSI B17.1-1967, R1989. Three Foot
Six Foot
Item No.
Item No.
GLH-3005 GLH-3010 GLH-3015 GLH-3025 GLH-3035 GLH-3040 GLH-3042 GLH-3045 GLH-3050
GLH-6005 GLH-6010 GLH-6015 GLH-6025 GLH-6035 GLH-6040 — GLH-6045 GLH-6050
Dia.
Pack Qty.
Keyway 1
1
⁄8 x 1⁄16 ⁄16 x 3⁄32 ⁄16 x 3⁄32 1 ⁄4 x 1⁄8 1 ⁄4 x 1⁄8 1 ⁄4 x 1⁄8 5 ⁄16 x 5⁄32 3 ⁄8 x 3⁄16 3 ⁄8 x 3⁄16
⁄2 ⁄8 3 ⁄4 1 13⁄16 11⁄4 13⁄8 17⁄16 11⁄2
1 1 1 1 1 1 1 1 1
3
5
3
Universal Joint Boots
Zinc Plated Steel
Stainless
Item No.
Item No.
Machined LSC-04 LSC-05 LSC-06 LSC-08 LSC-09 LSC-10 LSC-12 LSC-13 LSC-14 LSC-16 LSC-18 LSC-20 LSC-24 LSC-28
Use for Joint OD
Pack Qty.
1
⁄2 ⁄4 1
1 1 1
11⁄4 11⁄2
1 1
3
E
UJ-10 UJ-15 UJ-20 UJ-25 UJ-30 UJ-35 UJ-40 UJ-45 UJ-55
9 ⁄ ⁄16 5 ⁄ ⁄8 ⁄16 11⁄16 7 3 ⁄8 ⁄8 7 ⁄16 7⁄8 1 ⁄2 1 5 ⁄8 11⁄16 3 ⁄4 13⁄16 1 11⁄2 3
16 1 4
5
— — — UJ-325 — UJ-335 UJ-340 UJ-345 UJ-355
Bore Depth B C
— — — — — — 3 ⁄8 7⁄8 — — 1 ⁄2 1 5 ⁄8 11⁄16 3 ⁄4 13⁄16 1 11⁄2
B
1
⁄2 ⁄8 ⁄4 1 1 11⁄8 11⁄4 11⁄2 11⁄2 15⁄8 13⁄4 2 21⁄4 23⁄4 3
1
⁄4-20 ⁄4-20
1 1
1
Set Screw D
Pack Qty.
10-32 10-32 1 ⁄4-20 1 ⁄4-20 1 ⁄4-20 5 ⁄16-18 5 ⁄16-18 5 ⁄16-18 5 ⁄16-18 5 ⁄16-18 5 ⁄16-18 3 ⁄8-16 3 ⁄8-16 1 ⁄2-13
1 1 1 1 1 1 1 1 1 1 1 1 1 1
5
.2510 .3135 .3760 .5010 .5635 .6260 .7510 .8135 .8760 1.001 1.126 1.251 1.501 1.751
5
Set Screw Pack D Qty.
C
.7500 3⁄8 1.0000 3⁄8
C
⁄16 ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄
5
16 3 8 7 16 7 16 1 2 9 16 9 16 9 16 5 8 5 8 11 16 3 4 7 8
Solid Item No.
Steel
Stainless
Item No.
Item No.
A
CTC-200 CTC-202 CTC-204 CTC-206 CTC-208 CTC-210 CTC-212 CTC-250 CTC-255 CTC-214 CTC-216 CTC-218 CTC-220 CTC-222 CTC-224 CTC-226 CTC-228 CTC-232 CTC-230 CTC-231 CTC-234 CTC-238 CTC-236 CTC-242 CTC-244
— CTC-202SS — CTC-206SS — CTC-210SS CTC-212SS CTC-250SS CTC-255SS CTC-214SS CTC-216SS CTC-218SS CTC-220SS CTC-222SS CTC-224SS — — — — — — — — — —
⁄8 ⁄16 ⁄16 11 ⁄16 11 ⁄16 7 ⁄8 7 ⁄8 15 ⁄16 15 ⁄16 11⁄8 11⁄8 15⁄16 15⁄16 11⁄2 11⁄2 15⁄8 15⁄8 13⁄4 13⁄4 13⁄4 17⁄8 21⁄16 21⁄16 23⁄8 3
A
Standard industrial type universal joint with pin and block design. The special tapered shape of the yokes provide exceptional strength for long life while allowing full free movement of the joint. Boot retainer grooves are standard. Ideal for angles, degrees and speeds up to 1,750 rpm.
Item No.
Stamped LSC-2E 11⁄4 LSC-3E 11⁄2
B
A
UJ-110 3⁄8 UJ-115 1⁄2 UJ-120 5⁄8 UJ-125 3⁄4 UJ-130 7⁄8 UJ-135 1 UJ-140 11⁄4 UJ-145 11⁄2 — 2
Note: Static breaking torque is in inch lbs
D
E
Static Breaking Pack Keyway Torque Qty.
7 13⁄4 ⁄8 — 110 2 1 — 378 21⁄4 11⁄8 — 540 1 11 11 1 2 ⁄16 1 ⁄32 ⁄8 x ⁄16 768 3 11⁄2 — 1176 33⁄8 111⁄16 1⁄8 x 1⁄16 1560 33⁄4 17⁄8 3⁄16 x 3⁄32 5220 41⁄4 21⁄8 3⁄16 x 3⁄32 7920 57⁄16 223⁄32 1⁄4 x 1⁄8 15,600
5
11 11
B
C
10-32 1 ⁄4-20 1 ⁄4-28 5 ⁄16-18 5 ⁄16-24 3 ⁄8-16 3 ⁄8-24 7 ⁄16-14 7 ⁄16-20 1 ⁄2-13 1 ⁄2-20 5 ⁄8-11 5 ⁄8-18 3 ⁄4-10 3 ⁄4-16 7 ⁄8-9 7 ⁄8-14 1-14 1-8 1-12 11⁄8-12 11⁄4-12 11⁄4-7 11⁄2-12 2-12
5
⁄16 ⁄16 ⁄16 9 ⁄32 9 ⁄32 11 ⁄32 11 ⁄32 11 ⁄32 11 ⁄32 13 ⁄32 13 ⁄32 7 ⁄16 7 ⁄16 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 9 ⁄16 11 ⁄16 5 5
Clamp Screw Pack D Qty.
4-40 4-40 4-40 4-40 4-40 6-32 6-32 6-32 6-32 8-32 8-32 10-32 10-32 1 ⁄4-28 1 ⁄4-28 1 ⁄4-28 1 ⁄4-28 1 ⁄4-28 1 ⁄4-28 1 ⁄4-28 1 ⁄4-28 1 ⁄4-28 1 ⁄4-28 1 ⁄4-28 5 ⁄16-24
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Hexagon Bore Clamp Type Collars One-Piece or Two-Piece Inch Steel or Stainless Steel
B
Bore Depth B C
B
These threaded collars offer full radial holding power without marring the shaft.
C
Item No.
C
A
D E
Bored w/ Keyway
LSC-04SS LSC-05SS LSC-06SS LSC-08SS — LSC-10SS LSC-12SS LSC-13SS — LSC-16SS — LSC-20SS LSC-24SS —
D Clamp Screw
Universal Joints
Bored
A
Multiple Hump
Extends universal joint life by keeping dirt out and retaining lubrication. Installation is fast and easy. Includes two boots and four plastic ties.
One Hump UJ-215 UJ-225 UJ-235 Multiple Hump UJ-240 UJ-245
B
A
Shaft Collars, Threaded One Piece Inch Steel or Stainless Steel
One Hump
Item No.
Steel
C
1 1 1 1 1 1 1 1 1
One-Piece
Two-Piece
Clamp-type shaft collars to fit hexagon shafts. One-piece and two-piece made of steel and stainless steel. They can be modified (drilled, tapped, welded, etc.) to act as a mount for other components. They are non-marring and have high holding power. One-Piece Two-Piece Item No.
Steel CTC-502 CTC-503 — CTC-505 CTC-506 CTC-507 Stainless — CTC-601 CTC-602 CTC-603 CTC-604 CTC-605 CTC-607
Item No.
— CTC-553 CTC-554 CTC-555 CTC-556 CTC-557 CTC-650 — — CTC-653 CTC-654 CTC-655 CTC-657
Hex Bore
ID
OD
Width
Screw
Pack Qty.
⁄8 ⁄2 ⁄8 3 ⁄4 7 ⁄8 1
.375 .500 .625 .750 .875 1.000
1.063 1.250 1.500 1.875 2.000 2.125
.313 .375 .406 .500 .500 .500
6-32 8-32 10-32 1 ⁄4-28 1 ⁄4-28 1 ⁄4-28
1 1 1 1 1 1
1
.250 .313 .375 .500 .625 .750 1.000
.813 .813 1.063 1.250 1.500 1.875 2.125
.250 .250 .313 .375 .406 .500 .500
4-40 4-40 6-32 8-32 10-32 1 ⁄4-28 1 ⁄4-28
1 1 1 1 1 1 1
3 1 5
⁄4 ⁄ ⁄ ⁄ ⁄ ⁄ 1
5
16 3 8 1 2 5 8 3 4
891
BALL JOINTS & ROD ENDS E
Housing Width
N M
Ball Width
G
O
Wrench Flat
E
Available with steel or stainless steel housing and ball. The steel rod ends are available with reinforced nylon raceway or PTFE liner to eliminate the need for lubrication. The steel housing and ball are made from low carbon steel. The ball is case hardened and plated. The steel housing is plated and dichromate treated. The stud is permanently affixed and is made from heat treated alloy steel, zinc plated. The stainless rod end housing and ball are made from 303 stainless. Operating temperature from -30 degrees to 220 degrees Fahrenheit. Maximum misalignment is 55 degrees.
J
Bore Dia. L Ball Dia.
G
L Ball Dia.
A Thread Size
H
H
A Thread Size
R
Ball Width Housing Width
AA Bore Dia.
AA J
N M
P
Female Thread - Plain Ball End
Female Thread - Plain Ball End Steel, Nylon Raceway
Male Thread - Plain Ball End
Item No.
Thread Size A
Standard Threads SPF-3 10-32 .190/.192 1 SPF-4 ⁄4-28 .250/.252 5 SPF-5 ⁄16-24 .3125/.3145 3 SPF-6 ⁄8-24 .375/.377 7 SPF-7 ⁄16-20 .4375/.4395 1 SPF-8 ⁄2-20 .500/.502 SPF-10 5⁄8-18 .625/.627 SPF-12 3⁄4-16 .750/.752 Left Hand Threads 1 SPFL-4 ⁄4-28 .250/.252 SPFL-5 5⁄16-24 .3125/.3145 SPFL-6 3⁄8-24 .375/.377 SPFL-8 1⁄2-20 .500/.502 SPFL-10 5⁄8-18 .625/.627 SPFL-12 3⁄4-16 .750/.752
Female Thread - Plain Ball End Steel with PTFE Liner
Item No.
EF-4T EF-5T EF-6T EF-8T EF-10T
Thread Size A 1
⁄4-28 5 ⁄16-24 3 ⁄8-24 1 ⁄2-20 5 ⁄8-18
E
G
H
J
L
M
N
O
P
R
Pack Qty.
.625 .750 .875 1.000 1.125 1.312 1.500 1.750
1.062 1.312 1.375 1.625 1.812 2.125 2.500 2.875
.562 .750 .750 .937 1.031 1.187 1.500 1.562
1.375 1.687 1.812 2.125 2.375 2.781 3.250 3.750
.438 .516 .625 .719 .812 .938 1.125 1.312
.250 .281 .344 .406 .437 .500 .562 .687
.312 .375 .437 .500 .562 .625 .750 .875
.406 .469 .500 .687 .750 .875 1.000 1.125
.312 .375 .437 .562 .625 .750 .875 1.000
.406 .281 .281 .312 .625 .375 .500 1.000
1 1 1 1 1 1 1 1
.750 .875 1.000 1.312 1.500 1.750
1.312 1.375 1.625 2.125 2.500 2.875
.750 .750 .937 1.187 1.500 1.562
1.687 1.812 2.125 2.781 3.250 3.750
.516 .625 .719 .938 1.125 1.312
.281 .344 .406 .500 .562 .687
.375 .437 .500 .625 .750 .875
.469 .500 .687 .875 1.000 1.125
.375 .437 .562 .750 .875 1.000
.281 .281 .312 .375 .500 1.000
1 1 1 1 1 1
AA
AA
E
G
H
L
M
N
O
P
R
Pack Qty.
.2500 .3125 .3750 .5000 .6250
.750 .875 1.00 1.312 1.500
1.312 1.375 1.625 2.125 2.500
.687 .687 .812 1.187 1.406
.516 .625 .719 .938 1.125
.281 .344 .406 .500 .562
.375 .437 .500 .625 .750
.469 .500 .687 .875 1.000
.375 .437 .562 .750 .875
.250 .281 .312 .375 .500
1 1 1 1 1
Female Thread - Plain Ball End Stainless Steel, Molded Nylon Raceway Item No.
SSPF-3 SSPF-4 SSPF-5 SSPF-6 SSPF-7 SSPF-8 SSPF-10 SSPF-12
Thread Size A
AA
E
G
H
L
M
N
O
P
R
Pack Qty.
10-32 1 ⁄4-28 ⁄16-24 3 ⁄8-24 7 ⁄16-20 1 ⁄2-20 5 ⁄8-18 3 ⁄4-16
.1900 .2500 .3125 .3750 .4375 .5000 .6250 .7500
.625 .750 .875 1.000 1.125 1.312 1.500 1.750
1.062 1.312 1.375 1.625 1.812 2.125 2.500 2.875
.562 .750 .750 .937 1.031 1.187 1.500 1.562
.438 .516 .625 .719 .812 .938 1.125 1.312
.250 .281 .344 .406 .437 .500 .562 .687
.312 .375 .437 .500 .562 .625 .750 .875
.406 .469 .500 .687 .750 .875 1.000 1.125
.312 .375 .437 .562 .625 .750 .875 1.000
.406 .281 .281 .312 .625 .375 .500 1.000
1 1 1 1 1 1 1 1
5
Male Thread - Plain Ball End Steel with PTFE Liner Item No.
EM-4T EM-5T EM-6T EM-8T EM-10T
Thread Size A 1
⁄4-28 ⁄ -24 ⁄ -24 ⁄ -20 ⁄ -18
5
16 3 8 1 2 5 8
AA
E
G
H
L
M
N
Pack Qty.
.2500 .3125 .3750 .5000 .6250
.750 .875 1.000 1.312 1.500
1.562 1.875 1.937 2.437 2.625
1.000 1.250 1.250 1.500 1.625
.516 .625 .719 .938 1.125
.281 .344 .406 .500 .562
.375 .437 .500 .625 .750
1 1 1 1 1
Male Thread - Plain Ball End Stainless Steel, Molded Nylon Raceway
Male Thread - Plain Ball End Steel, Nylon Raceway
Item No.
Thread Size A
AA
E
G
H
L
M
N
Pack Qty.
SSPM-3 SSPM-4 SSPM-5 SSPM-6 SSPM-7 SSPM-8 SSPM-10 SSPM-12
10-32 1 ⁄4-28 5 ⁄16-24 3 ⁄8-24 7 ⁄16-20 1 ⁄2-20 5 ⁄8-18 3 ⁄4-16
.1900 .2500 .3125 .3750 .4375 .5000 .6250 .7500
.625 .750 .875 1.000 1.125 1.312 1.500 1.750
1.250 1.562 1.875 1.937 2.125 2.437 2.625 2.875
.750 1.000 1.250 1.250 1.312 1.500 1.625 1.750
.438 .516 .625 .719 .812 .938 1.125 1.312
.250 .281 .344 .406 .437 .500 .562 .687
.312 .375 .437 .500 .562 .625 .750 .875
1 1 1 1 1 1 1 1
AA
E
G
H
J
L
M
N
Pack Qty.
.190/.192 .250/.252 .3125/.3145 .375/.377 .4375/.4395 .500/.502 .625/.627 .750/.752
.625 .750 .875 1.000 1.125 1.312 1.500 1.750
1.250 1.562 1.875 1.937 2.125 2.437 2.625 2.875
.750 1.000 1.250 1.250 1.312 1.500 1.625 1.750
1.562 1.937 2.312 2.437 2.687 3.094 3.375 3.750
.438 .516 .625 .719 .812 .938 1.125 1.312
.250 .281 .344 .406 .437 .500 .562 .687
.312 .375 .437 .500 .562 .625 .750 .875
1 1 1 1 1 1 1 1
.190/.192 .250/.252 .3125/.3145 .375/.377 .4375/.4395 .500/.502 .625/.627 .750/.752
.625 .750 .875 1.000 1.125 1.312 1.500 1.750
1.250 1.562 1.875 1.937 2.125 2.437 2.625 2.875
.750 1.000 1.250 1.250 1.312 1.500 1.625 1.750
1.562 1.937 2.312 2.437 2.687 3.094 3.375 3.750
.438 .516 .625 .719 .812 .938 1.125 1.312
.250 .281 .344 .406 .437 .500 .562 .687
.312 .375 .437 .500 .562 .625 .750 .875
1 1 1 1 1 1 1 1
Item No.
Thread Size A
Standard Threads SPM-3 10-32 1 SPM-4 ⁄4-28 5 SPM-5 ⁄16-24 3 SPM-6 ⁄8-24 7 SPM-7 ⁄16-20 1 SPM-8 ⁄2-20 5 SPM-10 ⁄8-18 3 SPM-12 ⁄4-16 Left Hand Threads SPML-3 10-32 1 SPML-4 ⁄4-28 5 SPML-5 ⁄16-24 3 SPML-6 ⁄8-24 7 SPML-7 ⁄16-20 1 SPML-8 ⁄2-20 5 SPML-10 ⁄8-18 3 SPML-12 ⁄4-16
892
BALL JOINTS & ROD ENDS B
55°
D
MIN CONE
55° MIN CONE
F Hex
J J
L Ball Dia. A Thread Size
G A H Thread Size
G
L Ball Dia.
F Hex
A Thread Size
A Thread Size
H
R O
Wrench Flat
P
Low carbon steel housing and ball with reinforced nylon raceway or PTFE liner to eliminate the need for lubrication. The ball is case hardened and plated. The housing is plated and dichromate treated. The stud is permanently affixed and is made from heat treated alloy steel, zinc plated. Operating temperature from -30 degrees to 220 degrees Fahrenheit. Maximum misalignment is 55 degrees.
D
E
C
E
C
M B M
Female Thread - Ball End with Stud
Male Thread - Ball End with Stud
Female Thread - Ball End with Stud Steel, Nylon Raceway
Item No.
Thread Size A
Standard Threads SPF-3S 10-32 1 SPF-4S ⁄4-28 5 SPF-5S ⁄16-24 3 SPF-6S ⁄8-24 7 SPF-7S ⁄16-20 1 SPF-8S ⁄2-20 5 SPF-10S ⁄8-18 3 SPF-12S ⁄4-16
B
C
D
E
F
G
H
J
K
L
M
N
O
P
R
Pack Qty.
.437 .469 .531 .625 .844 .875 1.000 1.187
.437 .562 .687 .875 1.062 1.125 1.125 1.812
.156 .156 .187 .218 .312 .312 .375 .375
.625 .750 .875 1.000 1.125 1.312 1.500 1.750
.312 .375 .437 .500 .625 .625 .750 1.000
1.062 1.312 1.375 1.625 1.812 2.125 2.500 2.875
.562 .750 .750 .937 1.031 1.187 1.500 1.562
1.375 1.687 1.812 2.125 2.375 2.781 3.250 3.750
.187 .248 .310 .372 .435 .497 .622 .747
.438 .516 .625 .719 .812 .938 1.125 1.312
.250 .281 .344 .406 .437 .500 .562 .687
.312 .375 .437 .500 .562 .625 .750 .875
.406 .469 .500 .687 .750 .875 1.000 1.125
.312 .375 .437 .562 .625 .750 .875 1.000
.406 .406 .500 .562 .625 .687 .875 1.000
1 1 1 1 1 1 1 1
Female Thread - Plain Ball End Stamped Style Item No.
Thread Size A
Standard Threads ARE-10 10-32 1 ARE-20 ⁄4-28 ARE-30 5⁄16-24 3 ARE-40 ⁄8-24 1 ARE-50 ⁄2-20 Left Hand Threads 3 ARE-240 ⁄8-24
The economy stamped style combines high strength with low cost. Made from low carbon steel and plated for corrosion resistance. The ball is case hardened.
AA
E
G
H
J
L
M
N
O
P
Pack Qty.
.1900 .2500 .3125 .3750 .5000
.750 .850 1.015 1.125 1.470
1.062 1.312 1.375 1.625 2.125
.500 .687 .687 .875 1.125
1.437 1.737 1.882 2.187 2.860
.430 .510 .618 .713 .931
.250 .287 .305 .400 .500
.312 .375 .437 .500 .625
.450 .515 .590 .725 1.010
.312 .375 .437 .500 .625
1 1 1 1 1
.3750
1.125
1.625
.875
2.187
.713
.400
.500
.725
.500
1
Female Thread - Ball End with Stud Steel with PTFE Liner Item No.
Thread Size A
B
C
D
E
F
G
H
J
K
L
M
N
O
P
R
Pack Qty.
EFT-3S EFT-4S EFT-5S EFT-6S
10-32 1 ⁄4-28 5 ⁄16-24 3 ⁄8-24
.437 .469 .531 .625
.437 .562 .687 .875
.156 .156 .187 .218
.625 .750 .875 1.000
.312 .375 .437 .500
1.062 1.312 1.375 1.625
.500 .687 .687 .812
1.375 1.687 1.812 2.125
.187 .248 .310 .372
.438 .516 .625 .719
.250 .281 .344 .406
.312 .375 .437 .500
.406 .469 .500 .687
.312 .375 .437 .562
.406 .406 .500 .562
1 1 1 1
Note: K = Stud Neck Dia., L = Ball Dia., N = Ball Width
Male Thread - Ball End with Stud Steel, Nylon Raceway
Item No.
Thread Size A
Standard Threads SPM-3S 10-32 SPM-4S 1⁄4-28 SPM-5S 5⁄16-24 SPM-6S 3⁄8-24 SPM-7S 7⁄16-20 SPM-8S 1⁄2-20 SPM-10S 5⁄8-18 SPM-12S 3⁄4-16
B
C
D
E
F
G
H
J
K
L
M
N
Pack Qty.
.437 .469 .531 .625 .844 .875 1.000 1.187
.437 .562 .687 .875 1.062 1.125 1.125 1.812
.156 .156 .187 .218 .312 .312 .375 .375
.625 .750 .875 1.000 1.125 1.312 1.500 1.750
.312 .375 .437 .500 .625 .625 .750 1.000
1.250 1.562 1.875 1.937 2.125 2.437 2.625 2.875
.750 1.000 1.250 1.250 1.312 1.500 1.625 1.750
1.562 1.937 2.312 2.437 2.687 3.094 3.375 3.750
.187 .248 .310 .372 .435 .497 .622 .747
.438 .516 .625 .719 .812 .938 1.125 1.312
.250 .281 .344 .406 .437 .500 .562 .687
.312 .375 .437 .500 .562 .625 .750 .875
1 1 1 1 1 1 1 1
Male Thread - Ball End with Stud Steel with PTFE Liner Thread Size A
Item No.
EMT-3S 10-32 EMT-5S 5⁄16-24 EMT-6S 3⁄8-24
B
C
D
E
F
G
H
J
K
L
M
N
Pack Qty.
.437 .531 .625
.437 .687 .875
.156 .187 .218
.625 .875 1.000
.312 .437 .500
1.250 1.875 1.937
.750 1.250 1.250
1.562 2.312 2.437
.187 .310 .372
.438 .625 .719
.250 .344 .406
.312 .437 .500
1 1 1
Note: K = Stud Neck Dia., L = Ball Dia., N = Ball Width
Quick Disconnect Type
B
Swaged Construction
J
Retainer Sleeve
G
C
H
K
B
F
A Thread Size
D
C
A Thread Size
A
32° Cone
STQ-10 STQ-20
Thread A 1
⁄4-28 ⁄8-24
3
J
G H
E
These ball joints are high strength, quick disconnect assemblies with good wear characteristics. The retaining sleeve insures the assembly can only be put together with the sleeve positively aligned with the ball cavity. When spring is released, alignment is automatic thereby eliminating any possibility of partial closure. Body and ball stud are made of low carbon steel. Ball studs are surface hardened. All parts are plated and dichromate treated. Item No.
A
D E
B
C
D
E
G
H
J
Pack Qty.
.469 .687
.562 .875
.125 .187
.562 .750
.969 1.375
.531 .812
1.25 1.75
1 1
38° Conical
Unique assembly swages metal to retain the ball in the cavity resulting in increased pull out and wear resistance. Designed for heavy duty service, they come with a dirt shield to provide protection against contaminants. Made of low carbon steel, plated and dichromate treated. Ball studs are surface hardened. Item No.
STQ-30 STQ-40 STQ-50
Thread Size A
10-32 1 ⁄4-28 3 ⁄8-24
B
C
1
7
⁄8 1 ⁄16 17⁄32 31⁄32 111⁄16 13⁄8
D 7
⁄ ⁄ ⁄4
16 1 2
3
E 7
⁄ ⁄ ⁄
16 15 32 11 16
F 7
⁄16 ⁄ ⁄
9
16 7 8
G
H
1
1
1
3
3
3
⁄8 ⁄8 ⁄16
⁄16 ⁄32 ⁄32
J
K
⁄ ⁄ ⁄
3
5
16 3 8 1 2
⁄8 ⁄ ⁄
7
16 5 8
Pack Qty.
1 1 1
893
POLYMER ROD END & SPHERICAL BEARINGS These bearings are self-aligning, maintenance free and made of high performance polymer. Dust, dirt, corrosion and chemical resistant. Vibration dampening capacity. Suitable for rotary, oscillating and linear motions. Compensates for misalignment and edge loads. Lightweight and easy to install. Self-lubricating oil free operation Operates in temperatures from -40 degrees Fahrenheit to +275 degrees Fahrenheit. Metric dimensions are in millimeters. All are right hand threads. Female Thread Inch
H G
C
FA
B L J
K D M
E
Item No.
A
B
C
I-500 I-502 I-504 I-506 I-508 I-510 I-512 I-514
.190 .250 .312 .375 .437 .500 .625 .750
.307 .354 .447 .504 .600 .700 .838 .978
.625 .750 .875 1.000 1.125 1.312 1.500 1.750
D
E
F
G
H
J
K
L
M
Pack Qty.
10-32 1 ⁄4-28 ⁄16-24 3 ⁄8-24 7 ⁄16-20 1 ⁄2-20 5 ⁄8-18 3 ⁄4-16
.406 .469 .500 .687 .750 .875 1.000 1.125
.438 .516 .625 .718 .828 .938 1.125 1.312
.246 .272 .340 .394 .456 .487 .545 .676
.312 .375 .437 .500 .562 .625 .750 .875
1.062 1.312 1.375 1.625 1.812 2.125 2.500 2.875
.500 .687 .687 .812 .937 1.062 1.375 1.562
1.374 1.687 1.813 2.125 2.374 2.781 3.250 3.750
.312 .375 .437 .562 .625 .750 .875 1.000
1 1 1 1 1 1 1 1
5
Female Thread Metric
H G
FA
C
B L J
K D M
E I
Item No.
A
B
C
D
E
F
G
H
F
J
K
L
M
Pack Qty.
I-530 I-532 I-534 I-536 I-538 I-540 I-542
5 6 8 10 12 14 16
7.7 8.9 10.3 12.9 15.4 16.8 19.3
18 20 24 30 34 38 42
M5 x .8 M6 x 1.0 M8 x 1.25 M10 x 1.5 M12 x 1.75 M14 x 2.0 M16 x 2.0
9.0 10.0 12.5 15.0 17.5 20.0 22.0
11 13 16 19 22 25 29
6.0 7.0 9.0 10.5 12.0 13.5 15.0
8 9 12 14 16 19 21
11 13 16 19 22 25 29
27 30 36 43 50 57 64
10 12 16 20 22 25 28
36 40 48 58 67 76 85
SW9 SW11 SW14 SW17 SW19 SW22 SW22
1 1 1 1 1 1 1
Male Thread Inch and Metric
H G
C Item No.
FA L J K
D
Inch I-516 I-518 I-520 I-522 I-524 Metric I-550 I-552 I-554 I-558
A
C
.190 .250 .312 .375 .500
.625 .750 .875 1.000 1.312
6 8 10 14
20 24 30 38
D
F
G
H
J
K
L
Pack Qty.
10-32 1 ⁄4-28 ⁄16-24 3 ⁄8-24 1 ⁄2-20
.438 .516 .625 .718 .938
.234 .250 .312 .359 .453
.312 .375 .437 .500 .625
1.250 1.562 1.875 1.938 2.438
.750 1.000 1.250 1.250 1.500
1.563 1.937 2.312 2.438 3.094
1 1 1 1 1
M6 x 1.0 M8 x 1.25 M10 x 1.5 M14 x 2.0
12.7 15.8 19.0 25.4
7.0 9.0 10.5 13.5
9 12 14 19
36 42 48 60
21 25 28 36
46 54 63 79
1 1 1 1
5
Spherical Bearings Inch and Metric
B C
Item No.
30°
D F E A
30°
894
Inch I-570 I-571 I-572 I-573 I-575 I-576 I-577 Metric I-580 I-582 I-583 I-588 I-590
A
B
C
D
E
F
Pack Qty.
.1900 .2500 .3125 .3750 .5000 .6250 .7500
.312 .375 .437 .500 .625 .750 .875
.218 .250 .281 .312 .390 .500 .593
.5625 .6562 .7500 .8125 1.0625 1.1875 1.4375
.3070 .3540 .4470 .5040 .7000 .8381 .9781
.438 .516 .625 .718 .938 1.125 1.312
1 1 1 1 1 1 1
5 8 10 20 25
8 12 14 25 31
6.0 9.0 10.5 18.0 22.0
13 19 22 40 47
7.7 10.3 12.9 24.3 29.5
11.1 15.8 19.0 34.8 42.8
1 1 1 1 1
POSITIONING STAGES & LINEAR POSITION UNITS Ball Slide and Crossed Roller Positioning Stages Micrometer Driven
X Configuration
A C E
.03
Knurled Locking Screw
A C E
B D F
XY Configuration A C E
B D F L
B D F L Nominal
H
H M
L (Nominal)
M
Type A
Type B
L Nominal
J
A C
.16
H M
A C E
Type E
XYZ Configuration
B D BD
"Z" Bracket "Y" Stacking Plate .19 Thick
L L Nominal
.312 Dia. 8mm
1.69 H
H
.50 G
M
M
Type C
Type D
Type F
Positioning Stages - used for gauging and positioning light and medium loads. Applications include measuring instruments and optical assemblies. Spring loaded micrometer drives allow precise repeatable adjustments with low friction and zero backlash. Slides provide repeatability of .0001 inch. Ball slides provide accuracy to .0005/inch of travel, crossed roller slides .0001/inch of travel. Positioning slides can be stacked for multi axis applications. Preloaded positioning slides fully assembled and arrive ready to use. Black anodized finish. Item No.
Type
Travel
Config.
A
B
C
D
E
F
G
J
M
C'Bore For
.25 .50 .50 .50 .50 .50 .50 .50 .50 .50
X X X XY X X XY XYZ X XY
.75 1.25 1.75 1.75 1.50 2.00 2.00 2.00 3.25 3.25
.75 1.25 1.75 1.75 1.50 1.75 1.75 1.75 1.75 1.75
.562 1.000 1.500 1.500 1.187 .500 .500 .500 .550 .550
.531 1.000 1.500 1.500 1.187 .875 .875 .875 .875 .875
.312 .690 1.190 1.190 — .250 .250 .250 .250 .250
.312 .500 1.000 1.000 — — — — — —
— — — — — — — 1.12 — —
— — — — — .250 .250 — .250 —
.531 1.000 1.500 1.500 1.187 1.620 1.620 1.620 2.750 2.750
2-56 2-56 2-56 2-56 #4-M3 6-32-M4 6-32-M4 6-32-M4 6-32-M4 6-32-M4
8 10 10 10 4 8 8 8 12 12
.50 .50
X X
1.25 3.25
1.25 1.75
1.000 .550
1.000 .875
.690 .250
.500 —
— —
— .250
1.000 2-56 2.750 6-32-M4
10 12
Ball Slide DT-501 A DT-601 B DT-604 B DT-605 E DT-701 C DT-801 D DT-802 E DT-803 F DT-901 D DT-902 E Crossed Roller DT-651 B DT-951 D
Load Capacity Lbs. L
H
X,XY
Z
Pack Qty.
4 4 4 4 2 2 2 2 2 2
2.28 3.25 3.75 3.75 3.50 4.62 4.62 4.62 5.86 5.86
.53 .38 .38 .38 .62 .75 .75 .75 .75 .75
5 4 4 4 12 20 20 20 42 42
1.25 1.25 1.25 1.25 2.00 20.00 20.00 20.00 20.00 20.00
1 1 1 1 1 1 1 1 1 1
4 2
3.25 5.86
.38 .75
23 80
1.25 20.00
1 1
Carriage Base # Holes # Holes
Note: Column "J" is the distance from the carriage end to the center of the closest hole.
Linear Positioning Units M B C
A
A
D E
E
G H N
F
RKC-2001-RKC-2003
J K
RKC-2000 and RKC-2002
Effective way to position heavy loads in a particular location quickly and easily. Single pin unit offers high rigidity with small deflection. Uses an Acme right-hand threaded lead screw spindle with an attached drive nut to convert rotating input motion into linear motion. Positioning accuracy is +/-.2mm per 300 mm of travel. Can be readjusted quickly with two-spoke hand wheel with revolving handle (included). Work positioner is self-locking. Tube body is precision centerless ground stainless steel. Positioner mounts are cast aluminum. Hand wheel is die-cast aluminum with plastic coating and held in place by keyway lock. Hub is machined aluminum. Quick release handle included with each unit. Dimensions are in millimeters. Note: Hand wheel is unable to be removed from spindle after being installed. Load Capacity (Nm)
Item No.
Tube Dia.
A
B
C
D
E
F
Travel
X
Y
G
H
J
K
M
N
Pack Qty.
RKC-2000 RKC-2001 RKC-2002 RKC-2003
40 40 50 50
85 85 85 85
60 60 60 60
44 44 44 44
38 38 38 38
12 12 12 12
500 500 500 500
270 270 267 267
950 950 1500 1500
1000 1000 1500 1500
100 100 100 100
28 28 28 28
14 14 14 14
30 30 30 30
52 52 52 52
17 17 17 17
1 1 1 1
Note: Load capacity is based on ends being supported and positioner being stationary.
895
PRECISION LEAD SCREWS, NUTS & FLANGES Precision Acme lead screws are specifically designed for translating rotary motion into linear travel with accuracy and smoothness that are superior to general purpose Acme screws. Precision Acme lead screws are made from 4140 series alloy steel. Threads are rolled 2-C centralizing design. This thread form prevents wedging between nut and screw if subjected to radical loading. Screws have a minimum hardness of 200 Brinell. Tensile strength is rated at 95,000 psi and lead accuracy is maintained at +/-.003 in./ft. Screw ends are deburred and ready for end machining. Each screw is roller burnished and black oxide to a smooth finish, thereby maximizing travel efficiency. The matching travel nuts are engineered with the same 2-C centralizing thread form. Bronze nuts have ultimate tensile of 65,000 psi and a hardness of RB 75. A lubricated bronze nut has a dynamic COF of .125. The plastic nuts are quieter, more efficient and will equal or exceed the life of conventional travel nut materials. Tensile strength at 70 degree Fahrenheit is 8,000 psi. COF for a lubricated plastic nut is .075 (.160 unlubricated). Loads can be mounted to the travel nut or assembly with steel flanges. These flanges thread directly onto the travel nut. Nut and flange must be secured with a set screw or other pinning device. Application loads can be mounted to the flange via four pre-drilled, equally spaced holes. Mounting holes are .266" in diameter and spaced on the bolt center diameter (BCD) listed below. Acme Nuts
Acme Threaded Rod
Bronze 3 Foot Length Right Hand
Left Hand
Right Hand
Item No.
Item No.
Item No.
AR-2 AR-3 AR-4 AR-5 AR-6
AR-12 AR-13 AR-14 AR-15 —
— AR-23 AR-24 AR-25 AR-26
Plastic
Right Hand Left Hand Right Hand
6 Foot Length Thread Size Diameter
Thread Size TPI
Pack Qty.
12 10 8 6 6
1 1 1 1 1
3
⁄8 1 ⁄2 5 ⁄8 3 ⁄4 7 ⁄8
Item No.
Item No.
Item No.
Thread Size Diameter
AR-201 AR-202 AR-203 AR-204 AR-205 AR-206 —
— AR-212 AR-213 AR-214 AR-215 — AR-216
— AR-222 AR-223 AR-224 AR-225 — AR-226
Thread Size TPI
1
⁄4 ⁄8 ⁄2 5 ⁄8 3 ⁄4 7 ⁄8 7 ⁄8
9 16 9 16 15 16 15 16
16 12 10 8 6 6 6
3 1
External Thread Size
⁄ -18 ⁄ -18 ⁄ -16 ⁄ -16 1-18 13⁄8-16 3 1 ⁄8-18
Pack Qty.
1 1 1 1 1 1 1
Steel Flanges
Item No.
For Acme Nuts with Thread Size 1
AR-101 AR-102 AR-103 AR-104
Internal Thread Size
3
9
⁄ -16 and ⁄8-12 ⁄ -10 and 5⁄8-8 3 ⁄4-6 7 ⁄8-6
4 1 2
⁄ -18 ⁄ -16 1-18 13⁄8-16
16 15 16
Flange Dia.
Flange Thickness
Hole Spacing Bolt Circle Diameter
Pack Qty.
1.60 2.60 2.60 2.76
.410 .530 .530 .520
1.125 2.090 2.090 2.260
1 1 1 1
Universal Mounts for Acme and Ball Screws
P
H
C
B
E M F K
G
A
Use socket head cap screws for mounting. Pages 766-769. Item No.
AR-402 AR-403 AR-404 AR-405 AR-406
Fits Across Fits Ball Screw Dia. Screw Dia. 1
⁄2 ⁄8 ⁄4 7 ⁄8 — 5 3
— — .631 .750 1.000
P Lead
A
B
C
E
F
G
H
K
M
Thru
Countersink
Pack Qty.
— — .200 .200 .25 and 1.0
2.75 2.75 3.50 3.50 5.00
2.00 2.00 2.22 2.52 3.03
2.00 2.00 2.75 2.75 3.75
1.38 1.38 1.25 1.25 1.50
.310 .310 .500 .800 .750
1.19 1.18 1.38 1.38 1.72
.56 .56 .69 .69 .86
.28 .28 .28 .28 .47
1.000 1.000 1.187 1.438 1.625
.34 .34 .41 .41 .66
.5 x .56 .5 x .56 .62 x 1 .52 x 1 1 x 1.5
1 1 1 1 1
Note: Dimension P screw length based on 1.5 x. dia. extension beyond housing
896
BALL SCREWS, NUTS & FLANGES Ball Nuts - Right Hand Thread 1.200 Dia
E
E
C
D
D C Sq .500
B
A
B A
AR-314
C Sq
1.812
AR-315
F
D
B B E
AR-316
AR-344
B A
AR-345
C Sq
1.812
C
B
A
A
A
AR-346
.281 Dia (4) Holes on 2.250 BC Dia C Dia
F
F
F
C
E
D
D
D
C
E
F
C
E
F
F
F
45° Typ
D
D
D B
E
E
A
B
A
AR-347
E
2.760 Dia
A
AR-350
B
AR-351
Ball screws are convenient and efficient devices for converting rotary to linear motion. Because of their reliability and high efficiency they are utilized in replacing conventional methods of power transmission. Their high efficiency is developed by using bearing balls to limit friction between the nut and the screw. Unlimited travel is achieved by recirculating the bearing balls through return guides. All ball screws are right hand thread. Made of high quality alloy steel, induction hardened to RC 56-60. Flanges and nut are made of carburized steel with ball tracks heat treated to RC 58-60. Both ball screws and nuts have protective black oxide finish. Ball screws will not deviate from nominal lead by more than .004 inch per foot. Straight within .010 inch per foot. Do not exceed .030" in any 6' section. Load Lbs. Item No.
Ball Circle Dia.
Single Circuit AR-314 .631 AR-315 .750 AR-316 1.000 Double Circuit AR-344 .750 AR-345 .750 AR-350 1.000 AR-351 1.000 AR-346 1.000 AR-347 1.500
Lead
A
B
C
D
E
F
Dynamic
Static
Pack Qty.
Wiper Kit Item No.
.200 .200 .250
1.710 1.875 2.347
.500 .500 .600
1.000 1.312 1.500
.822 .863 1.104
.796 .886 1.152
.9375-16 1.173-18 1.563-18
815 1,100 1,612
6,384 8,569 13,913
1 1 1
— AR-371 AR-374
.200 .500 .250 .250 .500 1.000
2.875 2.927 3.000 3.000 3.130 3.628
.500 .500 .600 .375 .625 1.000
1.312 1.312 1.500 1.625 1.687 2.625
.863 .863 1.104 1.150 1.080 1.718
.886 .937 1.152 1.107 1.109 1.720
1.173-18 1.173-18 1.563-18 — 1.563-18 2.250-20
2,200 2,723 3,224 3,224 3,440 7,560
17,138 17,425 27,826 27,826 25,250 34,662
1 1 1 1 1 1
AR-371 AR-371 AR-376 AR-374 AR-375 AR-377
Flanges
Ball Screws
A C
Ball Circle Dia.
Lead
Lgth. Ft.
Pack Qty.
Item No.
Ball Circle Dia.
Lead
Lgth. Ft.
Pack Qty.
AR-302 .631 AR-303 .500 AR-304 .631 AR-305 .750 AR-306 1.000 AR-307 .631 AR-308 .750 AR-309 .750 AR-310 .750 AR-312 .750 AR-317 .750 AR-318 1.000 AR-319 1.000
.200 .500 .200 .200 .250 .200 .200 .200 .500 .500 .500 .250 .250
2 4 4 4 4 6 8 12 4 8 12 8 12
1 1 1 1 1 1 1 1 1 1 1 1 1
AR-320 AR-327 AR-328 AR-331 AR-332 AR-334 AR-335 AR-336 AR-337 AR-340 AR-341 AR-342
1.000 1.000 1.000 1.000 1.000 1.500 1.500 1.500 1.500 1.500 1.500 1.500
.250 .500 .500 1.000 1.000 1.000 1.000 1.000 1.000 1.875 1.875 1.875
16 12 16 12 16 8 12 16 20 12 16 20
1 1 1 1 1 1 1 1 1 1 1 1
Item No.
B
Item No.
For Nuts With Ball Circle dia.
A
B
Hole Dia.
C BCD
Pack Qty.
AR-323 AR-325 AR-326 AR-417
.631 .750 1.000 1.500
2.60 2.59 3.25 4.937
.53 .53 .64 1.020
.266 .281 .266 .531
2.09 2.09 2.75 4.125
1 1 1 1
*Flange also works with nuts with .500 ball circle diameter.
897
PRECISION BALL SCREWS & BALL NUTS 1.000 x .500 Non-Preload Right Hand
Ball Screws
These ball screws offer over 90% efficiency converting rotary motion to linear motion with low coefficient of friction. When replacing screws, hydraulics or pneumatics, they allow the use of smaller, less expensive drive motors and reduce the need for auxiliary equipment. They also offer dependable accuracy and repeatability at an economical price. Made of high-quality alloy steel hardened to rockwell 56-60C. Lead accuracy of .004 in./ft. Straight within .010 in/ft. and do not exceed .030" in any 6 foot section.
Ball Nut .105 1.363
Flange Ball-Nut Item No.
Wiper Kit
Thomson
Ball Circle Dia.
TBS-433 7824286
1.000
Ball Circle Dia.
Lead
Lgth.
Pack Qty.
Item No.
Ball Circle Dia.
Lead
Lgth.
Pack Qty.
TBS-17 .631 TBS-20 .631 TBS-23 .631 TBS-26 .631 TBS-29 .631 TBS-32 .750 TBS-35 .750 TBS-38 .750 TBS-47 .750 TBS-62 1.000
.200 .200 .200 .200 .200 .200 .200 .200 .500 .250
2 3 4 5 6 2 3 4 2 2
1 1 1 1 1 1 1 1 1 1
TBS-65 TBS-68 TBS-71 TBS-80 TBS-83 TBS-86 TBS-89 TBS-95 TBS-107 TBS-110
1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.500 1.500
.250 .250 .250 .500 .500 .500 .500 1.000 .250 .250
3 4 5 3 4 5 6 3 2 3
1 1 1 1 1 1 1 1 1 1
Item No. Lead
Dynamic Load
Static Load
Pack Qty.
.500
3,890
18,400
1
Flange Item No.
Thomson
Pack Qty.
Wiper Kit Item No.
Thomson
Pack Qty.
TBS-168
7824293
1
TBS-205
7824292
1
1.000 x 1.000 Non-Preload Right Hand - Square
Precision Ball Nuts .750 x .200 Non-Preload Right Hand 60°
.305 MAX 1.250-18 UNEF-3 TH’D
1/4-28 UNF-2B LUBE HOLE
.975 MAX
Ø1.300
.500
.926 MAX
Ball Nut
2.635
Ball Nut 2.090 BCD
.281 Dia.
10-24 UNC TH’D
.105 2.625
.188
1.586
1.031
.156 1.500
Flange
.530
Wiper Kit Flange
Ball-Nut Item No.
Thomson
Ball Circle Dia.
Lead
Dynamic Load
Static Load
Pack Qty.
TBS-436 5707509
1.000
1.000
2,142
11,925
1
Flange Item No.
TBS-165
Thomson
Pack Qty.
Wiper Kit Item No.
Thomson
Pack Qty.
5707571
1
TBS-208
5702650
1
Ball-Nut Item No.
1.000 x .250 Non-Preload Right Hand - Square
Wiper Kit
Thomson
Ball Circle Dia.
Lead
TBS-418 7824297
.750
.200
Flange Item No.
Thomson
TBS-159
7823336
Dynamic Load
Static Load
Pack Qty.
2,082
11,750
1
Pack Qty.
Wiper Kit Item No.
Thomson
Pack Qty.
1
TBS-193
7824337
1
Precision Ball Nuts .631 x .200 Preloaded Right Hand 1.128 DIA MAX
15/16-16 N-2 TH’D
.822 MAX
1.000 SQUARE
.500
.797 R MAX
3.510 REF
Ball Nut
Wiper Kit 2.090 BCD
.266 Dia.
6-32 NC-2 TH’D
.133
1.086 .105
1.586
.188
2.600 .961
.156 1.500 .530
Flange Ball-Nut Item No.
Wiper Kit
Flange
Wiper Kit
Thomson
Ball Circle Dia.
Lead
Dynamic Load
Static Load
Pack Qty.
TBS-424 5700348
1.000
.250
3,224
27,826
1
Ball-Nut Item No.
Thomson
Ball Circle Dia.
Lead
Dynamic Load
Static Load
Pack Qty.
TBS-415 7820955
.631
.200
778
6,384
1
Flange Item No.
Thomson
Pack Qty.
Wiper Kit Item No.
Thomson
Pack Qty.
Flange Item No.
Thomson
Pack Qty.
Wiper Kit Item No.
Thomson
Pack Qty.
TBS-165
5707571
1
TBS-208
5702650
1
TBS-156
5707570
1
TBS-190
5702647
1
898
CROSS BLOCKS & PRECISION BALL NUTS Used for connecting two round rods at 90 degrees. Adjustment can be made by loosening the hand knob. Plastic knobs function independently for precise adjustment. Knobs have a brass insert for easy turning and to prevent galling. Stainless steel eye bolt firmly clamps around the adjusting rod for superior holding strength. Eyelet does not mar the rod when tightened, resulting in a smooth rod surface that easily slides through the cross block. No set screws are used. Plastic or stainless steel bodies accept 1⁄2" or 5⁄8" rods. Several variations available with two knobs, nut and knob and two nuts. Stainless steel parts are made of Type 304 stainless steel. Heavy Duty Cross Blocks w/Two Nuts
Heavy Duty Cross Blocks w/One Nut and One Knob
A A
D
E
H
C
D
E
G B
H
G B
A
A
E
C
H
G B
H
Available with black plastic or stainless steel body, with stainless steel lock washers and nuts. Used when less frequent adjustments are necessary. Item No.
Rod Sizes
A
Plastic Body VG-13 1⁄2 x 1⁄2 3.4 VG-15 5⁄8 x 5⁄8 3.4 Stainless Steel Body 1 1 VG-16 ⁄2 x ⁄2 3.4 VG-17 1⁄2 x 5⁄8 3.4 VG-18 5⁄8 x 5⁄8 3.4
E
B
D
E
G
H
Pack Qty.
2.31 2.31
1.41 1.41
1.31 1.31
1 1
0.66 0.66
1 1
2.31 2.31 2.31
— — —
1.25 1.25 1.25
1 1 1
0.66 0.66 0.66
1 1 1
G B
Available with black plastic or stainless steel body and plastic knob. Stainless steel washer and nut. Use hand knob for frequent adjustments. Use lock washer and nut for more permanent positioning. Item No.
Rod Sizes
A
Plastic Body VG-7 1⁄2 x 1⁄2 3.7 VG-9 5⁄8 x 5⁄8 3.7 Stainless Steel Body 1 1 VG-10 ⁄2 x ⁄2 3.8 VG-11 1⁄2 x 5⁄8 3.8 VG-12 5⁄8 x 5⁄8 3.8
B
C
D
E
G
H
Pack Qty.
2.31 2.31
2 2
1.41 1.41
1.31 1.31
1 1
0.66 0.66
1 1
2.31 2.31 2.31
2 2 2
— — —
1.25 1.25 1.25
1 1 1
0.66 0.66 0.66
1 1 1
Precision Ball Nuts .631 x .200 Non-Preload Right Hand
1.000 SQUARE
15/16-16N-2 TH’D
.822 MAX
.500
.797 R MAX
1.710
Ball Nut
2.090 BCD
.266 Dia.
6-32 NC-2 TH’D 1.086
.133
.105
2.600 .961
.530
Wiper Kit
Flange Ball-Nut Item No.
Thomson
Ball Circle Dia.
Lead
Dynamic Load
Static Load
Pack Qty.
Flange Item No.
Thomson
Pack Qty.
Wiper Kit Item No.
Thomson
Pack Qty.
TBS-412 7820827
.631
.200
778
6,384
1
TBS-156
5707570
1
TBS-190
5702647
1
899
OIL & GREASE SEALS Oil and Grease Seals Inch
Oil seals are used to seal around a rotating shaft and keep an oil-based lubricant inside an axle or housing. Grease seals are used to seal more viscous grease lubricants in a variety of rotary shaft applications. Styles with double lips, enhanced lip compound materials, and/or a spring on one of the lips increase the effectiveness of the oil or grease seal in extreme environments - keeping contaminants out and lubrication in. Item No.
Inch - Oil DNA-10 DNA-20 DNA-25 DNA-30 DNA-35 DNA-40 DNA-45 DNA-55 DNA-60 DNA-65 DNA-70 DNA-75 DNA-80 DNA-85 DNA-90 DNA-95 DNA-100 DNA-105 DNA-110 DNA-115 DNA-120 DNA-125 DNA-135 DNA-140 DNA-145 DNA-150 DNA-155 DNA-165 DNA-170 DNA-175 DNA-185 DNA-190 DNA-195 DNA-200 DNA-205 DNA-210 DNA-215 DNA-220 DNA-225 DNA-230 DNA-235 DNA-240 DNA-245 DNA-250 DNA-255 DNA-260 DNA-265 DNA-270 DNA-275 DNA-280 DNA-285 DNA-290 DNA-295 DNA-300 DNA-305 DNA-310 DNA-315 DNA-320 DNA-325 DNA-330 DNA-335 DNA-340
Shaft
0.375 0.500 0.500 0.500 0.500 0.563 0.625 0.625 0.625 0.625 0.625 0.625 0.625 0.750 0.750 0.750 0.750 0.750 0.750 0.750 0.750 0.813 0.875 0.875 0.875 0.875 0.938 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.125 1.125 1.125 1.125 1.125 1.125 1.188 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.313 1.375 1.375 1.375 1.375 1.375 1.375 1.375 1.375 1.375 1.375 1.375
Bore
0.875 0.999 0.999 1.124 1.375 1.124 0.875 0.999 1.124 1.124 1.375 1.375 1.624 1.125 1.250 1.250 1.312 1.375 1.375 1.499 1.624 1.624 1.250 1.375 1.375 1.499 1.375 1.375 1.437 1.437 1.499 1.499 1.874 2.000 2.000 1.624 1.874 1.874 2.000 2.000 2.062 2.000 1.687 1.750 2.000 2.000 2.062 2.124 2.374 2.437 2.062 1.750 1.874 1.938 2.000 2.000 2.063 2.125 2.250 2.374 2.562 2.562
Width
0.250 0.250 0.250 0.250 0.250 0.250 0.125 0.250 0.250 0.250 0.250 0.250 0.312 0.250 0.250 0.250 0.250 0.250 0.250 0.250 0.250 0.250 0.188 0.250 0.312 0.250 0.250 0.250 0.250 0.250 0.250 0.250 0.250 0.250 0.250 0.250 0.250 0.250 0.250 0.250 0.250 0.250 0.313 0.250 0.250 0.250 0.250 0.250 0.313 0.375 0.313 0.219 0.250 0.250 0.312 0.313 0.313 0.313 0.312 0.312 0.375 0.375
Note: Synthetic rubber O.D.
900
Case Lip Profile Material
TB TB TB TB TB TB TZ TB TB TB TB TB TB TB TB TB TB TB TB TB TB TB TB TB TA TB TB TZ TB TB TB TB TB TB TB TB TB TB TB TB TB TB TB TL TB TB TB TB TB TB TB TB TB TB TB TB TB TB TB TB TB TB
Nitrile Viton Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Viton Nitrile Viton Nitrile Nitrile Nitrile Viton Nitrile Nitrile Viton Nitrile Nitrile Nitrile Nitrile Nitrile Viton Nitrile Nitrile Nitrile Nitrile Nitrile Viton Viton Nitrile Nitrile Viton Nitrile Nitrile Viton Nitrile Nitrile Viton Nitrile Nitrile Nitrile Nitrile Viton Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Viton Nitrile Viton Nitrile Nitrile Nitrile Nitrile Viton
Pack Qty.
Item No.
Shaft
Bore
Width
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
DNA-345 DNA-350 DNA-360 DNA-365 DNA-370 DNA-375 DNA-380 DNA-385 DNA-390 DNA-395 DNA-400 DNA-405 DNA-410 DNA-415 DNA-420 DNA-425 DNA-430 DNA-435 DNA-440 DNA-445 DNA-450 DNA-455 DNA-460 DNA-465 DNA-470 DNA-475 DNA-480 DNA-485 DNA-490 DNA-495 DNA-500 DNA-505 DNA-510 DNA-515 DNA-520 DNA-525 DNA-530 DNA-535 DNA-540 DNA-545 DNA-550 DNA-555 DNA-560 DNA-565 DNA-570 DNA-575 DNA-580 DNA-585 DNA-590 DNA-595 DNA-600 DNA-605 DNA-610 DNA-615 DNA-620 DNA-625 DNA-630 DNA-635 DNA-640 DNA-645 DNA-650 DNA-655 DNA-660
1.375 1.438 1.500 1.500 1.500 1.500 1.500 1.500 1.563 1.625 1.625 1.625 1.625 1.625 1.625 1.750 1.750 1.750 1.750 1.750 1.875 1.875 1.938 1.938 2.000 2.000 2.000 2.000 2.000 2.125 2.125 2.125 2.188 2.250 2.250 2.250 2.250 2.250 2.375 2.375 2.500 2.500 2.500 2.625 2.625 2.750 2.750 2.875 2.875 2.938 2.938 2.938 3.000 3.000 3.000 3.125 3.125 3.125 3.250 3.250 3.375 3.375 3.375
2.875 2.250 2.000 2.250 2.250 2.374 2.750 3.000 2.374 2.000 2.250 2.374 2.437 2.750 3.000 2.374 2.437 2.686 2.750 3.000 2.686 2.875 2.686 3.000 2.686 2.750 2.875 3.000 3.062 2.750 2.875 3.000 3.000 3.000 3.061 3.125 3.500 3.623 3.000 3.125 3.500 3.623 3.876 3.623 3.750 3.500 3.751 3.623 3.751 3.751 3.876 4.000 4.125 4.249 4.999 4.125 4.249 4.999 4.249 4.501 4.125 4.376 4.501
0.468 0.313 0.375 0.313 0.313 0.313 0.312 0.375 0.313 0.250 0.313 0.313 0.313 0.312 0.312 0.313 0.313 0.375 0.313 0.375 0.375 0.313 0.313 0.313 0.375 0.313 0.313 0.313 0.375 0.375 0.438 0.375 0.375 0.375 0.375 0.375 0.438 0.468 0.375 0.375 0.375 0.375 0.468 0.375 0.375 0.375 0.375 0.375 0.375 0.375 0.375 0.438 0.437 0.437 0.438 0.375 0.438 0.468 0.375 0.438 0.375 0.375 0.438
Case Lip Profile Material
TB TB TB TB TB TB TB TB TB TB TB TB TB TB TA TB TB TB TB TB TB TB TL TB TB TB TA TB TB TB TB TA TB TB TB TB TA TA TB TB TA TB TA TA TB TA TA TB TA TB TA TA TA TA TA TA TA TA TA TA TA TA TA
Nitrile Nitrile Nitrile Viton Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Viton Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Viton Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile
Pack Qty.
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Item No.
Shaft
DNA-665 3.375 DNA-670 3.438 DNA-675 3.500 DNA-680 3.500 DNA-685 3.500 DNA-690 3.500 DNA-695 3.500 DNA-700 3.500 DNA-705 3.500 DNA-710 3.625 DNA-715 3.625 DNA-720 3.625 DNA-725 3.688 DNA-730 3.750 DNA-735 3.750 DNA-740 3.875 DNA-745 4.000 DNA-750 4.000 DNA-755 4.000 DNA-760 4.000 DNA-765 4.000 DNA-770 4.000 DNA-775 4.000 DNA-780 4.000 DNA-785 4.125 DNA-790 4.250 DNA-795 4.250 DNA-800 4.250 DNA-805 4.250 DNA-810 4.375 DNA-815 4.375 DNA-820 4.500 DNA-825 4.500 DNA-830 4.625 DNA-835 4.750 DNA-840 4.750 DNA-845 4.875 DNA-850 4.875 DNA-855 5.000 DNA-860 5.000 DNA-865 5.000 DNA-870 5.000 DNA-875 5.000 DNA-880 5.250 DNA-885 5.250 DNA-890 5.500 DNA-895 5.500 DNA-900 5.750 DNA-905 5.750 DNA-910 6.000 DNA-915 6.000 DNA-920 6.500 DNA-925 7.000 DNA-930 8.000 DNA-935 9.000 Inch - Grease DNA-5 0.375 DNA-15 0.500 DNA-50 0.625 DNA-130 0.875 DNA-160 1.000 DNA-180 1.000 DNA-355 1.500
Case Lip Profile Material
Pack Qty.
Bore
Width
4.999 4.626 4.376 4.501 4.625 4.875 4.999 5.126 5.500 4.376 4.626 4.999 4.501 4.751 4.999 5.251 4.999 4.999 5.125 5.250 5.376 5.501 5.751 5.999 5.251 5.251 5.376 5.500 5.626 5.376 5.500 5.750 5.999 5.625 5.751 6.001 5.999 6.250 6.001 6.250 6.499 7.000 7.500 6.250 6.500 6.500 6.750 6.751 7.500 7.000 7.500 8.000 8.500 9.500 11.000
0.438 0.438 0.375 0.438 0.500 0.500 0.468 0.438 0.500 0.375 0.438 0.375 0.438 0.375 0.438 0.438 0.375 0.438 0.500 0.500 0.500 0.562 0.562 0.500 0.468 0.375 0.500 0.500 0.500 0.500 0.500 0.500 0.500 0.500 0.500 0.500 0.500 0.500 0.500 0.563 0.500 0.500 0.500 0.500 0.562 0.562 0.500 0.500 0.562 0.500 0.500 0.625 0.625 0.625 0.750
TA TA TB TA TA TA TA TA TA TA TA TB TA TB TA TA TB TA TA TA TA TA TA TA TA TB TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA TA
Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Viton Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
0.687 0.750 0.938 1.250 1.250 1.499 1.874
0.156 0.125 0.188 0.182 0.125 0.188 0.250
VM VM VB VB KM VB VB
Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile
1 1 1 1 1 1 1
OIL & GREASE SEALS Oil and Grease Seals Metric
Oil seals are used to seal around a rotating shaft and keep an oil-based lubricant inside an axle or housing. Grease seals are used to seal more viscous grease lubricants in a variety of rotary shaft applications. Styles with double lips, enhanced lip compound materials, and/or a spring on one of the lips increase the effectiveness of the oil or grease seal in extreme environments - keeping contaminants out and lubrication in. Item No.
Shaft
Bore
Metric - Oil DNA-955 DNA-965 DNA-970 DNA-975 DNA-980 DNA-985 DNA-990 DNA-1000 DNA-1005 DNA-1010 DNA-1015 DNA-1020 DNA-1025 DNA-1030 DNA-1035 DNA-1040 DNA-1045 DNA-1050 DNA-1055 DNA-1060 DNA-1065 DNA-1070 DNA-1075 DNA-1080 DNA-1085 DNA-1090 DNA-1095 DNA-1100 DNA-1105 DNA-1110 DNA-1120 DNA-1125 DNA-1130 DNA-1135 DNA-1140 DNA-1145 DNA-1155 DNA-1160 DNA-1165 DNA-1170 DNA-1175 DNA-1180 DNA-1185 DNA-1190 DNA-1200 DNA-1205 DNA-1210 DNA-1215 DNA-1225 DNA-1230 DNA-1235 DNA-1240 DNA-1245 DNA-1255 DNA-1260 DNA-1265 DNA-1270 DNA-1275 DNA-1280 DNA-1285 DNA-1290 DNA-1295 DNA-1300 DNA-1305 DNA-1310 DNA-1315 DNA-1320 DNA-1325 DNA-1330 DNA-1335 DNA-1340 DNA-1345 DNA-1350 DNA-1355 DNA-1360 DNA-1365 DNA-1370 DNA-1375 DNA-1380 DNA-1385 DNA-1390
8 10 10 10 10 10 11 12 12 12 12 12 12 12 14 14 14 15 15 15 15 15 15 15 15 16 16 16 16 16 17 17 17 17 17 17 18 18 18 18 19 19 19 20 20 20 20 20 20 20 20 20 20 22 22 22 22 22 22 22 23 24 24 25 25 25 25 25 25 25 25 25 25 25 26 26 26 27 27 28 28
16 19 20 22 24 25 17 18 19 20 22 24 25 28 20 22 24 24 25 26 27 28 30 32 35 24 28 30 32 35 28 29 30 32 35 40 28 30 32 47 32 35 47 26 30 32 35 36 40 42 45 47 52 32 35 38 40 42 47 50 34 35 40 35 37 38 40 42 44 45 46 47 52 62 37 40 47 37 43 38 40
Case Lip Width Profile Material
7 7 7 7 7 7 4 4 5 4 7 7 7 7 3 4 7 7 4 7 7 7 7 7 7 7 7 7 7 7 7 5 6 7 8 5 7 7 7 10 8 7 7 4 7 7 7 7 7 7 7 7 10 7 7 7 7 7 7 10 8 6 7 7 7 7 5 7 7 8 7 8 10 7 7 7 7 7 8 7 7
TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TF TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC
Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile
Pack Qty.
Item No.
Shaft
Bore
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
DNA-1395 DNA-1400 DNA-1405 DNA-1410 DNA-1415 DNA-1420 DNA-1425 DNA-1430 DNA-1435 DNA-1440 DNA-1445 DNA-1450 DNA-1455 DNA-1460 DNA-1465 DNA-1470 DNA-1475 DNA-1480 DNA-1485 DNA-1490 DNA-1495 DNA-1500 DNA-1505 DNA-1510 DNA-1515 DNA-1520 DNA-1525 DNA-1530 DNA-1535 DNA-1540 DNA-1545 DNA-1550 DNA-1555 DNA-1560 DNA-1565 DNA-1570 DNA-1575 DNA-1580 DNA-1585 DNA-1590 DNA-1595 DNA-1600 DNA-1605 DNA-1610 DNA-1615 DNA-1620 DNA-1625 DNA-1630 DNA-1635 DNA-1640 DNA-1645 DNA-1650 DNA-1655 DNA-1660 DNA-1665 DNA-1670 DNA-1675 DNA-1680 DNA-1685 DNA-1690 DNA-1695 DNA-1700 DNA-1705 DNA-1710 DNA-1715 DNA-1720 DNA-1725 DNA-1730 DNA-1735 DNA-1740 DNA-1745 DNA-1750 DNA-1755 DNA-1760 DNA-1765 DNA-1770 DNA-1775 DNA-1780 DNA-1785 DNA-1790 DNA-1795 DNA-1800
28 28 28 30 30 30 30 30 30 30 30 30 30 30 30 30 32 32 32 32 32 34 34 34 35 35 35 35 35 35 35 35 35 35 36 36 38 38 38 38 38 38 40 40 40 40 40 40 40 40 40 40 40 40 40 42 42 42 42 43 44 44 45 45 45 45 45 45 45 45 45 48 48 48 48 50 50 50 50 50 50 50
42 47 52 37 40 42 44 45 46 47 48 50 52 55 62 72 45 46 47 52 72 47 48 52 45 47 48 50 52 54 55 62 72 80 47 52 50 52 55 58 60 72 50 52 54 55 56 58 60 62 64 68 70 72 80 55 60 62 72 62 60 62 55 58 60 62 65 72 75 80 85 62 65 68 72 60 62 65 68 70 72 80
Case Lip Width Profile Material
7 7 6 4 7 8 7 8 8 7 8 7 8 10 8 10 7 8 7 8 10 10 7 8 7 7 8 8 7 8 8 10 10 10 7 7 7 8 8 10 10 8 8 7 7 8 7 8 10 10 12 7 10 10 10 7 9 8 10 8 10 8 7 7 7 8 8 10 8 10 10 8 10 10 10 8 7 8 8 10 8 8
TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC
Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile
Pack Qty.
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Item No.
Case Lip Width Profile Material
Pack Qty.
Shaft
Bore
DNA-1805 50 DNA-1810 52 DNA-1815 52 DNA-1820 52 DNA-1825 55 DNA-1830 55 DNA-1835 55 DNA-1840 55 DNA-1845 55 DNA-1850 55 DNA-1855 55 DNA-1860 55 DNA-1865 56 DNA-1870 58 DNA-1875 58 DNA-1880 60 DNA-1885 60 DNA-1890 60 DNA-1895 60 DNA-1900 60 DNA-1905 60 DNA-1910 60 DNA-1915 60 DNA-1920 62 DNA-1925 62 DNA-1930 65 DNA-1935 65 DNA-1940 65 DNA-1945 65 DNA-1950 65 DNA-1955 68 DNA-1960 70 DNA-1965 70 DNA-1970 70 DNA-1975 70 DNA-1980 70 DNA-1985 70 DNA-1990 75 DNA-1995 75 DNA-2000 75 DNA-2005 75 DNA-2010 75 DNA-2015 80 DNA-2020 80 DNA-2025 80 DNA-2030 85 DNA-2035 85 DNA-2040 85 DNA-2045 85 DNA-2050 90 DNA-2055 90 DNA-2060 90 DNA-2065 95 DNA-2070 100 DNA-2075 100 DNA-2080 100 DNA-2085 100 DNA-2090 105 DNA-2095 110 DNA-2100 115 DNA-2105 120 DNA-2110 120 DNA-2115 120 DNA-2120 125 DNA-2125 130 DNA-2130 140 DNA-2135 150 DNA-2140 160 DNA-2145 180 DNA-2150 200 DNA-2155 220 Metric - Grease DNA-940 6 DNA-945 6 DNA-950 8 DNA-960 10 DNA-995 12 DNA-1115 17 DNA-1150 18 DNA-1195 20 DNA-1220 20 DNA-1250 22
90 62 68 72 68 70 72 78 80 85 90 100 72 72 80 75 78 80 82 85 90 95 110 80 85 80 85 88 90 100 90 80 85 90 92 95 100 95 100 105 110 115 100 105 110 100 110 120 130 105 110 120 120 120 125 130 150 130 140 140 140 150 160 150 160 170 180 190 210 230 250
10 8 8 8 8 8 10 12 10 10 10 10 8 8 12 8 9 10 12 10 10 10 10 10 8 8 10 12 10 10 10 10 8 12 12 13 10 10 10 13 10 9 10 10 10 13 12 12 12 10 12 13 12 10 12 12 13 12 12 13 13 12 12 12 12 12 15 15 15 13 15
TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC
Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
10 13 12 17 16 23 24 26 40 28
2 4 3 3 3 3 3 4 5 4
VC VC VC VG VG VG KC VC KC KC
Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile Nitrile
1 1 1 1 1 1 1 1 1 1
Note: Synthetic rubber O.D.
901
INDUSTRIAL V-BELTS Single Wedge Premium Notched
Single wedge V-belts, 3VX and 5VX in raw edge notched construction give premium belt performance. The belts are constructed of highly engineered, high performance, oil and heat resistant components. The components are made using the latest in belt technology available on a global basis. The "X" in the part number refers to higher load ratings than standard wedge V-belts. The belts exceed USA RMA published ratings levels. They are designed to perform at the identical or higher level than all other major USA manufacturer's belts of the same type. All 3VX and 5VX belts are manufactured to meet RMA standards for length, dimensions and matching. All belts of a given size are manufactured to run interchangeably in a matched set. Belt Lgth. Top Pack (Inch) Width Thickness Qty.
Item No.
3VX Type BTQ-3VX240 BTQ-3VX250 BTQ-3VX255 BTQ-3VX265 BTQ-3VX280 BTQ-3VX300 BTQ-3VX315 BTQ-3VX335 BTQ-3VX340 BTQ-3VX355 BTQ-3VX360 BTQ-3VX375 BTQ-3VX400 BTQ-3VX425 BTQ-3VX450 BTQ-3VX475 BTQ-3VX500 BTQ-3VX530 BTQ-3VX560 BTQ-3VX600 BTQ-3VX630 BTQ-3VX670
24 25 25.5 26.5 28 30 31.5 33.5 34 35.5 36 37.5 40 42.5 45 47.5 50 53 56 60 63 67
3
5
3
5
⁄8 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8
⁄16 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Item No.
Belt Lgth. Top Pack (Inch) Width Thickness Qty.
3VX Type BTQ-3VX710 71 BTQ-3VX750 75 BTQ-3VX800 80 BTQ-3VX850 85 BTQ-3VX900 90 BTQ-3VX950 95 BTQ-3VX1000 100 BTQ-3VX1060 106 BTQ-3VX1120 112 BTQ-3VX1180 118 BTQ-3VX1250 125 BTQ-3VX1320 132 BTQ-3VX1400 140 5VX Type BTQ-5VX400 40 BTQ-5VX425 42.5 BTQ-5VX450 45 BTQ-5VX475 47.5 BTQ-5VX500 50 BTQ-5VX510 51 BTQ-5VX530 53 BTQ-5VX540 54
3
⁄8 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8
5
3
5
⁄16 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16
1 1 1 1 1 1 1 1 1 1 1 1 1
5
17
5
17
5
17
1 1 1 1 1 1 1 1
⁄8 ⁄8 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8
⁄32 ⁄32 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32
Belt Lgth. Top Pack (Inch) Width Thickness Qty.
Item No.
5VX Type BTQ-5VX550 BTQ-5VX560 BTQ-5VX570 BTQ-5VX580 BTQ-5VX590 BTQ-5VX600 BTQ-5VX610 BTQ-5VX630 BTQ-5VX650 BTQ-5VX660 BTQ-5VX670 BTQ-5VX680 BTQ-5VX690 BTQ-5VX710 BTQ-5VX730 BTQ-5VX740 BTQ-5VX750 BTQ-5VX780 BTQ-5VX800 BTQ-5VX810 BTQ-5VX830 BTQ-5VX840
5
17
5
17
⁄8 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8
55 56 57 58 59 60 61 63 65 66 67 68 69 71 73 74 75 78 80 80 83 84
⁄32 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Belt Lgth. Top Pack (Inch) Width Thickness Qty.
Item No.
5VX Type BTQ-5VX850 BTQ-5VX860 BTQ-5VX880 BTQ-5VX900 BTQ-5VX930 BTQ-5VX950 BTQ-5VX960 BTQ-5VX1000 BTQ-5VX1030 BTQ-5VX1060 BTQ-5VX1080 BTQ-5VX1120 BTQ-5VX1150 BTQ-5VX1180 BTQ-5VX1250 BTQ-5VX1320 BTQ-5VX1400 BTQ-5VX1500 BTQ-5VX1600 BTQ-5VX1700 BTQ-5VX1800 BTQ-5VX1900
85 86 88 90 93 95 96 100 103 106 108 112 115 118 125 132 140 150 160 170 180 190
5
17
5
17
5
17
⁄8 ⁄8 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8
⁄32 ⁄32 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Single Classical Premium Notched
Single classical V-belts, AX, BX and CX in raw edge notched construction give premium belt performance. The belts are constructed of highly engineered, high performance, oil and heat resistant components. The components are made using the latest in belt technology available on a global basis. The "X" in the part number refers to higher load ratings than standard classical wrapped belts. The belts exceed USA RMA published ratings levels. They are designed to perform at the identical or higher level than all other major USA manufacturer's belts of the same type. All AX, BX and CX belts are manufactured to meet RMA standards for length, dimensions and matching. All belts of a given size are manufactured to run interchangeably in a matched set. Item No.
AX Type BTQ-AX20 BTQ-AX21 BTQ-AX22 BTQ-AX23 BTQ-AX24 BTQ-AX25 BTQ-AX26 BTQ-AX27 BTQ-AX28 BTQ-AX29 BTQ-AX30 BTQ-AX31 BTQ-AX32 BTQ-AX33 BTQ-AX34 BTQ-AX35 BTQ-AX36 BTQ-AX37 BTQ-AX38 BTQ-AX39 BTQ-AX40 BTQ-AX41 BTQ-AX42 BTQ-AX43 BTQ-AX44 BTQ-AX45 BTQ-AX46 BTQ-AX47 BTQ-AX48 BTQ-AX49 BTQ-AX50 BTQ-AX51 BTQ-AX52 BTQ-AX53 BTQ-AX54 BTQ-AX55 BTQ-AX56 BTQ-AX57 BTQ-AX58 BTQ-AX59 BTQ-AX60 BTQ-AX61 BTQ-AX62 BTQ-AX63 BTQ-AX64
902
Belt Lgth. Top Pack (Inch) Width Thickness Qty.
22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66
1
5
1
5
1
5
⁄2 ⁄2 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2
⁄16 ⁄16 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Item No.
AX Type BTQ-AX65 BTQ-AX66 BTQ-AX67 BTQ-AX68 BTQ-AX69 BTQ-AX70 BTQ-AX71 BTQ-AX72 BTQ-AX73 BTQ-AX74 BTQ-AX75 BTQ-AX76 BTQ-AX77 BTQ-AX78 BTQ-AX79 BTQ-AX80 BTQ-AX81 BTQ-AX82 BTQ-AX83 BTQ-AX84 BTQ-AX85 BTQ-AX86 BTQ-AX87 BTQ-AX88 BTQ-AX89 BTQ-AX90 BTQ-AX91 BTQ-AX92 BTQ-AX93 BX Type BTQ-BX30 BTQ-BX31 BTQ-BX32 BTQ-BX33 BTQ-BX34 BTQ-BX35 BTQ-BX36 BTQ-BX37 BTQ-BX38 BTQ-BX39 BTQ-BX40 BTQ-BX41 BTQ-BX42 BTQ-BX43 BTQ-BX44
Belt Lgth. Top Pack (Inch) Width Thickness Qty.
67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95
1
⁄2 ⁄2 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2
5
1
5
1
5
⁄16 ⁄16 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
33 34 35 36 37 38 39 40 41 42 43 44 45 46 47
5
13
5
13
5
13
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
⁄8 ⁄8 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8
⁄32 ⁄32 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32
Item No.
BX Type BTQ-BX45 BTQ-BX46 BTQ-BX47 BTQ-BX48 BTQ-BX49 BTQ-BX50 BTQ-BX51 BTQ-BX52 BTQ-BX53 BTQ-BX54 BTQ-BX55 BTQ-BX56 BTQ-BX57 BTQ-BX58 BTQ-BX59 BTQ-BX60 BTQ-BX61 BTQ-BX62 BTQ-BX63 BTQ-BX64 BTQ-BX65 BTQ-BX66 BTQ-BX67 BTQ-BX68 BTQ-BX69 BTQ-BX70 BTQ-BX71 BTQ-BX72 BTQ-BX73 BTQ-BX74 BTQ-BX75 BTQ-BX76 BTQ-BX77 BTQ-BX78 BTQ-BX79 BTQ-BX80 BTQ-BX81 BTQ-BX82 BTQ-BX83 BTQ-BX84 BTQ-BX85 BTQ-BX86 BTQ-BX87 BTQ-BX88 BTQ-BX89
Belt Lgth. Top Pack (Inch) Width Thickness Qty.
48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92
5
13
5
13
5
13
⁄8 ⁄8 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8
⁄32 ⁄32 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Item No.
BX Type BTQ-BX90 BTQ-BX91 BTQ-BX92 BTQ-BX93 BTQ-BX94 BTQ-BX95 BTQ-BX96 BTQ-BX97 BTQ-BX99 BTQ-BX100 BTQ-BX103 BTQ-BX105 BTQ-BX108 BTQ-BX112 BTQ-BX113 BTQ-BX115 BTQ-BX116 BTQ-BX120 BTQ-BX124 BTQ-BX128 BTQ-BX133 BTQ-BX136 BTQ-BX144 CX Type BTQ-CX51 BTQ-CX55 BTQ-CX60 BTQ-CX68 BTQ-CX72 BTQ-CX75 BTQ-CX78 BTQ-CX81 BTQ-CX85 BTQ-CX90 BTQ-CX96 BTQ-CX105 BTQ-CX112 BTQ-CX120 BTQ-CX124 BTQ-CX128 BTQ-CX144 BTQ-CX173
Belt Lgth. Top Pack (Inch) Width Thickness Qty.
93 94 95 96 97 98 99 100 101 103 106 108 111 115 116 118 119 123 127 131 136 139 147
5
⁄8 ⁄8 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8
13
5
13
5
13
⁄32 ⁄32 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
55 59 64 72 76 79 82 85 89 94 100 109 116 124 128 132 148 177
7
17
7
17
7
17
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
⁄8 ⁄8 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8
⁄32 ⁄32 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32
INDUSTRIAL V-BELTS Single Classical Single classical V-belts, A, B, C and D in fabric wrapped construction give premium belt performance. The belts are constructed of highly engineered, high performance and heat resistant materials. The outer fabric wrap is treated with oil and heat resistant, engineered synthetic rubber coated compound, specifically compounded for excellent wear resistance, proven through thousands of hours of testing. The components are made using the latest in belt technology available on a global basis. The belts exceed USA RMA published ratings levels. They are designed to perform at the identical or higher level than all other major USA manufacturer's belts of the same type. All A, B, C and D V-belts are manufactured to meet RMA standards for length, dimensions and matching. All belts of a given size are manufactured to run interchangeably in a matched set. Item No.
A Type BTQ-A14 BTQ-A15 BTQ-A16 BTQ-A17 BTQ-A18 BTQ-A19 BTQ-A20 BTQ-A21 BTQ-A22 BTQ-A23 BTQ-A24 BTQ-A25 BTQ-A26 BTQ-A27 BTQ-A28 BTQ-A29 BTQ-A30 BTQ-A31 BTQ-A32 BTQ-A33 BTQ-A34 BTQ-A35 BTQ-A36 BTQ-A37 BTQ-A38 BTQ-A39 BTQ-A40 BTQ-A41 BTQ-A42 BTQ-A43 BTQ-A44 BTQ-A45 BTQ-A46 BTQ-A47 BTQ-A48 BTQ-A49 BTQ-A50 BTQ-A51 BTQ-A52 BTQ-A53 BTQ-A54 BTQ-A55 BTQ-A56 BTQ-A57 BTQ-A58 BTQ-A59 BTQ-A60 BTQ-A61 BTQ-A62 BTQ-A63 BTQ-A64 BTQ-A65 BTQ-A66 BTQ-A67 BTQ-A68 BTQ-A69 BTQ-A70 BTQ-A71 BTQ-A72 BTQ-A73 BTQ-A74 BTQ-A75 BTQ-A76 BTQ-A77 BTQ-A78 BTQ-A79 BTQ-A80 BTQ-A81 BTQ-A82 BTQ-A83 BTQ-A84 BTQ-A85 BTQ-A86 BTQ-A87 BTQ-A88 BTQ-A89 BTQ-A90 BTQ-A91 BTQ-A92 BTQ-A93 BTQ-A94 BTQ-A95 BTQ-A96 BTQ-A97 BTQ-A98 BTQ-A99 BTQ-A100 BTQ-A101 BTQ-A102 BTQ-A103 BTQ-A104
Belt Lgth. Top Pack (Inch) Width Thickness Qty.
16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106
1
5
1
5
⁄2 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2
⁄16 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Item No.
A Type BTQ-A105 BTQ-A106 BTQ-A108 BTQ-A110 BTQ-A112 BTQ-A115 BTQ-A116 BTQ-A120 BTQ-A126 BTQ-A128 BTQ-A133 BTQ-A135 BTQ-A136 BTQ-A138 BTQ-A140 BTQ-A144 BTQ-A158 BTQ-A173 BTQ-A176 BTQ-A180 B Type BTQ-B20 BTQ-B21 BTQ-B22 BTQ-B23 BTQ-B24 BTQ-B25 BTQ-B26 BTQ-B27 BTQ-B28 BTQ-B29 BTQ-B30 BTQ-B31 BTQ-B32 BTQ-B33 BTQ-B34 BTQ-B35 BTQ-B36 BTQ-B37 BTQ-B38 BTQ-B39 BTQ-B40 BTQ-B41 BTQ-B42 BTQ-B43 BTQ-B44 BTQ-B45 BTQ-B46 BTQ-B47 BTQ-B48 BTQ-B49 BTQ-B50 BTQ-B51 BTQ-B52 BTQ-B53 BTQ-B54 BTQ-B55 BTQ-B56 BTQ-B57 BTQ-B58 BTQ-B59 BTQ-B60 BTQ-B61 BTQ-B62 BTQ-B63 BTQ-B64 BTQ-B65 BTQ-B66 BTQ-B67 BTQ-B68 BTQ-B69 BTQ-B70 BTQ-B71 BTQ-B72 BTQ-B73 BTQ-B74 BTQ-B75 BTQ-B76 BTQ-B77 BTQ-B78 BTQ-B79 BTQ-B80 BTQ-B81 BTQ-B82 BTQ-B83 BTQ-B84 BTQ-B85 BTQ-B86 BTQ-B87 BTQ-B88 BTQ-B89
Belt Lgth. Top Pack (Inch) Width Thickness Qty.
107 108 110 112 114 117 118 122 128 130 135 137 138 140 142 146 160 175 177 182
1
⁄2 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2 1 ⁄2
5
1
5
23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92
5
13
5
13
5
13
⁄8 ⁄8 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8
⁄16 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 ⁄32 ⁄32 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32
Item No.
Belt Lgth. Top Pack (Inch) Width Thickness Qty.
B Type 1 BTQ-B90 93 1 BTQ-B91 94 1 BTQ-B92 95 1 BTQ-B93 96 1 BTQ-B94 97 1 BTQ-B95 98 1 BTQ-B96 99 1 BTQ-B97 100 1 BTQ-B98 101 1 BTQ-B99 102 1 BTQ-B101 103 1 BTQ-B100 103 1 BTQ-B102 105 1 BTQ-B103 106 1 BTQ-B104 107 1 BTQ-B105 108 1 BTQ-B106 109 1 BTQ-B107 110 1 BTQ-B108 111 1 BTQ-B109 112 BTQ-B110 113 1 BTQ-B111 114 1 BTQ-B112 115 1 BTQ-B113 116 1 BTQ-B114 117 1 BTQ-B115 118 1 BTQ-B116 119 1 BTQ-B117 120 1 BTQ-B118 121 1 BTQ-B120 123 1 BTQ-B122 125 1 BTQ-B123 126 1 BTQ-B124 127 1 BTQ-B125 128 1 BTQ-B126 129 1 BTQ-B128 131 1 BTQ-B130 133 1 BTQ-B131 134 1 BTQ-B132 135 1 BTQ-B133 136 1 BTQ-B134 137 1 BTQ-B135 138 1 BTQ-B136 139 1 BTQ-B137 140 1 BTQ-B138 141 1 BTQ-B140 143 1 BTQ-B141 144 1 BTQ-B142 145 1 BTQ-B143 146 1 BTQ-B144 147 1 BTQ-B145 148 1 BTQ-B146 149 1 BTQ-B147 150 1 BTQ-B148 151 1 BTQ-B150 153 1 BTQ-B152 155 1 BTQ-B153 156 1 BTQ-B154 157 1 BTQ-B155 158 1 BTQ-B156 159 1 BTQ-B158 161 1 BTQ-B160 163 1 BTQ-B162 165 1 BTQ-B163 166 1 BTQ-B164 167 1 BTQ-B165 168 1 BTQ-B166 169 1 BTQ-B167 170 1 BTQ-B168 171 1 BTQ-B169 172 1 BTQ-B170 173 1 BTQ-B173 176 1 BTQ-B175 178 1 BTQ-B178 181 1 BTQ-B180 183 1 BTQ-B182 185 1 BTQ-B185 188 1 BTQ-B187 190 1 BTQ-B190 193 1 BTQ-B192 195 1 BTQ-B195 198 1 BTQ-B196 199 1 BTQ-B199 202 1 BTQ-B204 207 1 BTQ-B205 208 1 BTQ-B210 213 1 BTQ-B214 215.4 1 BTQ-B215 216.4 1 BTQ-B218 219.4 1 BTQ-B220 221.4 1 BTQ-B221 222.4
5
13
5
13
⁄8 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8
⁄32 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Item No.
B Type BTQ-B225 BTQ-B236 BTQ-B237 BTQ-B240 BTQ-B255 BTQ-B257 BTQ-B260 BTQ-B270 BTQ-B285 BTQ-B292 BTQ-B293 BTQ-B300 BTQ-B315 BTQ-B330 BTQ-B360 C Type BTQ-C46 BTQ-C48 BTQ-C49 BTQ-C51 BTQ-C52 BTQ-C54 BTQ-C55 BTQ-C56 BTQ-C57 BTQ-C60 BTQ-C61 BTQ-C62 BTQ-C63 BTQ-C64 BTQ-C65 BTQ-C66 BTQ-C68 BTQ-C70 BTQ-C71 BTQ-C72 BTQ-C73 BTQ-C75 BTQ-C76 BTQ-C78 BTQ-C79 BTQ-C80 BTQ-C81 BTQ-C82 BTQ-C83 BTQ-C84 BTQ-C85 BTQ-C86 BTQ-C87 BTQ-C88 BTQ-C90 BTQ-C91 BTQ-C92 BTQ-C93 BTQ-C94 BTQ-C95 BTQ-C96 BTQ-C97 BTQ-C98 BTQ-C99 BTQ-C100 BTQ-C101 BTQ-C102 BTQ-C103 BTQ-C104 BTQ-C105 BTQ-C106 BTQ-C107 BTQ-C108 BTQ-C109 BTQ-C110 BTQ-C111 BTQ-C112 BTQ-C113 BTQ-C114 BTQ-C115 BTQ-C116 BTQ-C117 BTQ-C118 BTQ-C119 BTQ-C120 BTQ-C122 BTQ-C124 BTQ-C125 BTQ-C126 BTQ-C128 BTQ-C130 BTQ-C131 BTQ-C132 BTQ-C133 BTQ-C136
Belt Lgth. Top Pack (Inch) Width Thickness Qty.
226.4 237.4 238.4 241.4 256.4 258.4 261.4 271.4 286.4 293.4 294.4 301.4 316.4 331.4 361.4
5
⁄8 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8
13
5
13
⁄32 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32 13 ⁄32
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
50 52 53 55 56 57 59 60 61 64 65 66 67 68 69 70 72 74 75 76 77 79 80 82 83 84 85 86 87 88 89 90 91 92 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 126 128 129 130 132 134 135 136 137 140
7
17
7
17
7
17
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
⁄8 ⁄8 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8
⁄32 ⁄32 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32
Item No.
C Type BTQ-C138 BTQ-C139 BTQ-C140 BTQ-C141 BTQ-C142 BTQ-C144 BTQ-C147 BTQ-C148 BTQ-C150 BTQ-C151 BTQ-C152 BTQ-C153 BTQ-C154 BTQ-C155 BTQ-C156 BTQ-C158 BTQ-C160 BTQ-C162 BTQ-C164 BTQ-C165 BTQ-C166 BTQ-C167 BTQ-C169 BTQ-C170 BTQ-C171 BTQ-C173 BTQ-C175 BTQ-C177 BTQ-C180 BTQ-C183 BTQ-C184 BTQ-C185 BTQ-C188 BTQ-C190 BTQ-C195 BTQ-C196 BTQ-C197 BTQ-C202 BTQ-C206 BTQ-C207 BTQ-C210 BTQ-C212 BTQ-C218 BTQ-C225 BTQ-C235 BTQ-C240 BTQ-C246 BTQ-C250 BTQ-C255 BTQ-C270 BTQ-C280 BTQ-C285 BTQ-C300 BTQ-C315 BTQ-C330 BTQ-C345 BTQ-C360 BTQ-C390 BTQ-C420 D Type BTQ-D105 BTQ-D112 BTQ-D120 BTQ-D128 BTQ-D144 BTQ-D147 BTQ-D158 BTQ-D162 BTQ-D171 BTQ-D173 BTQ-D178 BTQ-D180 BTQ-D195 BTQ-D210 BTQ-D225 BTQ-D240 BTQ-D255 BTQ-D270 BTQ-D285 BTQ-D300 BTQ-D315 BTQ-D330 BTQ-D345 BTQ-D360 BTQ-D390 BTQ-D420 BTQ-D450 BTQ-D480 BTQ-D540
Belt Lgth. Top Pack (Inch) Width Thickness Qty.
142 143 144 145 146 148 151 152 153 155 156 157 158 159 160 162 164 166 168 169 170 171 173 174 175 177 179 181 184 187 188 189 192 194 199 200 201 206 210 211 214 214.2 220.2 227.2 237.2 242.2 248.2 252.2 257.2 272.2 282.2 287.2 302.2 317.2 332.2 345.2 362.2 392.2 422.2 110.2 117.2 125.2 133.2 149.2 152.2 163.2 167.2 176.2 178.2 183.2 185.2 200.2 215.2 227.7 242.7 257.7 272.7 287.7 302.7 317.7 332.7 347.7 362.7 392.7 422.7 452.7 482.7 542.7
7
⁄8 ⁄8 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8
17
7
17
7
17
11⁄4 11⁄4 11⁄4 11⁄4 11⁄4 11⁄4 11⁄4 11⁄4 11⁄4 11⁄4 11⁄4 11⁄4 11⁄4 11⁄4 11⁄4 11⁄4 11⁄4 11⁄4 11⁄4 11⁄4 11⁄4 11⁄4 11⁄4 11⁄4 11⁄4 11⁄4 11⁄4 11⁄4 11⁄4
3
⁄32 ⁄32 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 ⁄4 ⁄4 ⁄4 3 ⁄4 3 ⁄4 3 ⁄4 3 ⁄4 3 ⁄4 3 ⁄4 3 ⁄4 3 ⁄4 3 ⁄4 3 ⁄4 3 ⁄4 3 ⁄4 3 ⁄4 3 ⁄4 3 ⁄4 3 ⁄4 3 ⁄4 3 ⁄4 3 ⁄4 3 ⁄4 3 ⁄4 3 ⁄4 3 ⁄4 3 ⁄4 3 ⁄4 3 ⁄4 3 3
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
903
INDUSTRIAL V-BELTS & PULLEYS Single Wedge
Single wedge V-belts, 3V, 5V and 8V in fabric wrapped construction give premium belt performance. The belts are constructed of highly engineered, high performance and heat resistant materials. The outer fabric wrap is treated with oil and heat resistant, engineered synthetic rubber coated compound, specifically compounded for excellent wear resistance, proven through thousands of hours of testing. The components are made using the latest in belt technology available on a global basis. The belts exceed USA RMA published ratings levels. They are designed to perform at the identical or higher level than all other major USA manufacturer's belts of the same type. All 3V, 5V and 8V V-belts are manufactured to meet RMA standards for length, dimensions and matching. All belts of a given size are manufactured to run interchangeably in a matched set. Item No.
3V Type BTQ-3V250 BTQ-3V265 BTQ-3V280 BTQ-3V300 BTQ-3V315 BTQ-3V335 BTQ-3V355 BTQ-3V375 BTQ-3V400 BTQ-3V425 BTQ-3V450 BTQ-3V475 BTQ-3V500 BTQ-3V530 BTQ-3V560 BTQ-3V600 BTQ-3V630 BTQ-3V670 BTQ-3V710 BTQ-3V750 BTQ-3V800 BTQ-3V850 BTQ-3V900 BTQ-3V950 BTQ-3V1000
Belt Lgth. Top Pack (Inch) Width Thickness Qty.
25 26.5 28 30 31.5 33.5 35.5 37.5 40 42.5 45 47.5 50 53 56 60 63 67 71 75 80 85 90 95 100
3
5
3
5
⁄8 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8
⁄16 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Item No.
3V Type BTQ-3V1060 BTQ-3V1120 BTQ-3V1180 BTQ-3V1250 BTQ-3V1320 BTQ-3V1400 5V Type BTQ-5V500 BTQ-5V530 BTQ-5V560 BTQ-5V600 BTQ-5V630 BTQ-5V670 BTQ-5V710 BTQ-5V750 BTQ-5V800 BTQ-5V850 BTQ-5V900 BTQ-5V950 BTQ-5V1000 BTQ-5V1060 BTQ-5V1120 BTQ-5V1180 BTQ-5V1250 BTQ-5V1320
Belt Lgth. Top Pack (Inch) Width Thickness Qty.
106 112 118 125 132 140
3
⁄8 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8 3 ⁄8
5
3
5
⁄16 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16
1 1 1 1 1 1
50 53 56 60 63 67 71 75 80 85 90 95 100 106 112 118 125 132
5
17
5
17
5
17
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
⁄8 ⁄8 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8
⁄32 ⁄32 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32
Belt Lgth. Top Pack (Inch) Width Thickness Qty.
Item No.
5V Type BTQ-5V1400 BTQ-5V1500 BTQ-5V1600 BTQ-5V1700 BTQ-5V1800 BTQ-5V1900 BTQ-5V2000 BTQ-5V2120 BTQ-5V2240 BTQ-5V2360 BTQ-5V2500 BTQ-5V2650 BTQ-5V2800 BTQ-5V3000 BTQ-5V3150 BTQ-5V3350 BTQ-5V3550 8V Type BTQ-8V1000 BTQ-8V1060 BTQ-8V1120 BTQ-8V1180 BTQ-8V1250 BTQ-8V1320 BTQ-8V1400
140 150 160 170 180 190 200 212 224 236 250 265 280 300 315 335 355 100 106 112 118 125 132 140
5
⁄8 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8 5 ⁄8
17
5
17
⁄32 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32 17 ⁄32
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
11⁄2 11⁄2 11⁄2 11⁄2 11⁄2 11⁄2 11⁄2
29
1 1 1 1 1 1 1
⁄32 ⁄32 ⁄32 29 ⁄32 29 ⁄32 29 ⁄32 29 ⁄32 29 29
Belt Lgth. Top Pack (Inch) Width Thickness Qty.
Item No.
8V Type BTQ-8V1500 BTQ-8V1600 BTQ-8V1700 BTQ-8V1800 BTQ-8V1900 BTQ-8V2000 BTQ-8V2120 BTQ-8V2240 BTQ-8V2360 BTQ-8V2500 BTQ-8V2650 BTQ-8V2800 BTQ-8V3000 BTQ-8V3150 BTQ-8V3350 BTQ-8V3550 BTQ-8V3750 BTQ-8V4000 BTQ-8V4250 BTQ-8V4500 BTQ-8V4750 BTQ-8V5000 BTQ-8V5600
150 160 170 180 190 200 212 224 236 250 265 280 300 315 335 355 375 400 425 450 475 500 560
11⁄2 11⁄2 11⁄2 11⁄2 11⁄2 11⁄2 11⁄2 11⁄2 11⁄2 11⁄2 11⁄2 11⁄2 11⁄2 11⁄2 11⁄2 11⁄2 11⁄2 11⁄2 11⁄2 11⁄2 11⁄2 11⁄2 11⁄2
29
⁄32 ⁄32 ⁄32 29 ⁄32 29 ⁄32 29 ⁄32 29 ⁄32 29 ⁄32 29 ⁄32 29 ⁄32 29 ⁄32 29 ⁄32 29 ⁄32 29 ⁄32 29 ⁄32 29 ⁄32 29 ⁄32 29 ⁄32 29 ⁄32 29 ⁄32 29 ⁄32 29 ⁄32 29 ⁄32 29 29
Precision Ground Idler Shafts
C
B
A D
E F
Idler Shafts - Coarse Thread Item No.
IDC-161 IDC-162 IDC-163 IDC-164 IDC-165 IDC-166 IDC-167
A
B
1
1
1 ⁄16 11⁄2 21⁄2 31⁄2 31⁄4 51⁄4 11⁄16
C
D
1
3
1 ⁄2 21⁄8 31⁄8 41⁄8 4 6 11⁄2
⁄2 1 1 1 11⁄2 11⁄2 1 ⁄2
A
B
C
1
1
⁄8 5 ⁄8 11⁄8 15⁄8 13⁄8 21⁄2 3 ⁄8
F
Approx. Weight (Lbs.)
Pack Qty.
⁄8-16 THD ⁄4-10 THD ⁄4-10 THD 3 ⁄4-10 THD 1-8 THD 1-8 THD 3 ⁄8-16 THD
.16 .75 .95 1.16 2.61 3.64 .16
1 1 1 1 1 1 1
F
Approx. Weight (Lbs.)
Pack Qty.
⁄4-16 THD ⁄4-16 THD ⁄4-16 THD 1-14 THD 1-14 THD
.75 .95 1.16 2.61 3.64
1 1 1 1 1
E 7
⁄ ⁄ ⁄8 7 ⁄8 15⁄16 15⁄16 7 ⁄16 16 7 8
7
3
3 3
Idler Shafts - Fine Thread Item No.
IDC-168 IDC-169 IDC-170 IDC-171 IDC-172
904
1 ⁄2 21⁄2 31⁄2 31⁄4 51⁄4
2 ⁄8 31⁄8 41⁄8 4 6
1 1 1 11⁄2 11⁄2
D
E
5
7
3
7
3
7
3
⁄8 11⁄8 15⁄8 13⁄8 21⁄2
⁄8 ⁄8 ⁄8 15⁄16 15⁄16
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
PULLEYS & TENSIONERS V-Belt Idler Pulley
D
C B Item No.
Belt Type
IDC-118 IDC-119 IDC-121 IDC-122 IDC-123 IDC-124
A
A A B, C B, C B, C B, C
A
B
.86 .86 1.31 1.31 1.31 1.31
1
C
3 ⁄2 31⁄2 51⁄16 51⁄16 75⁄16 75⁄16
Pack Qty.
D
3
23
1
23
1
23
⁄8 ⁄2 ⁄2 5 ⁄8 1 ⁄2 5 ⁄8
⁄32 ⁄32 ⁄32 23 ⁄32 23 ⁄32 23 ⁄32
1 1 1 1 1 1
Flat Faced Idler Pulleys - Needle Bearing
B E F
H
A DC Item No.
IDC-127 IDC-128 IDC-129 IDC-130
B
A
B
1
7
4 ⁄2 41⁄2 41⁄2 7
C
1 ⁄16 27⁄16 37⁄16 5
1 1 1 1
D
E
4 4 4 6
1
F
G
1
1 ⁄16 21⁄16 31⁄16 41⁄2
H
⁄16 ⁄16 ⁄16 11⁄8
1 ⁄2 31⁄2 31⁄2 51⁄8
1
Pack Qty.
3.00 4.60 5.80 13.20
1 1 1 1
1
1
1
Approx. Weight (Lbs.)
⁄8 ⁄8 ⁄8 1 ⁄8
1
1
Adjustable Flange Tensioners
F G
L-BOLT
The adjustable flange tensioner has a flanged base that can be mounted in a tight area where space is limited. The rotating arm gives the operator 360 degree controlled tensioning and can be easily adjusted to the proper tension increasing the life of the drive. The adjustable flange tensioner has serrated teeth to prevent slippage. Idler shaft must be ordered separately.
E
K J C D
Item No.
C
D
E
F
G
J
K
L
IDC-62 IDC-63
1 1
17⁄8 17⁄8
11⁄2 11⁄2
4 4
3 3
3 3
2 2
3
Approx. Weight (Lbs.)
Pack Qty.
2.82 2.82
1 1
⁄8 3 ⁄8
E T E NSIO
J K NE
E
R
E
DR I V
Adjustable Angle Tensioners
C
AD
JU
ST
AB
L
N
G
L-BOLT
M
D
I H
F
The adjustable angle tensioner has an angled base that can be mounted on the top of a frame member. The angled base provides parallel tensioning with the drive. This tensioner has serrated teeth to prevent slippage. Idler shaft must be ordered separately. Item No.
C
D
E
F
G
H
I
J
K
IDC-67 IDC-69
1 11⁄2
11⁄4 13⁄4
11⁄2 23⁄8
2 31⁄2
4 73⁄8
4 71⁄2
3 6
3 61⁄2
2 5
L 3
⁄4-16 x 3⁄8 1-14 x 5⁄8
M 1
⁄2 3 ⁄4
N
Approx. Weight (Lbs.)
Pack Qty.
21⁄2 51⁄8
3.15 14.20
1 1
905
TENSIONERS, BELLOWS & POWDERED BRONZE BARS Adjustable Screw Tensioners L
CAP SCREW
N
AT MAX. ADJ.
C
GF M
I
D
MAX. ADJ.
H
K
E
J
The adjustable screw tensioner uses screw adjustment for positive precise tensioning. Can be easily mounted to any flat surface and a favorite for operators that need to make very fine adjustments. Idler shaft must be ordered separately. Item No.
C
D
E
F
G
IDC-82 IDC-83
1 11⁄2
21⁄2 35⁄8
11⁄2 23⁄8
93⁄8 16
83⁄8 141⁄2
H 3
⁄4 11⁄4
I 1
⁄2 3 ⁄4
J
K
23⁄8 43⁄8
1 13⁄4
L
M
N
Approx. Weight (Lbs.)
Pack Qty.
⁄4-16 x 3⁄8 1-14 x 5⁄8
4 8
23⁄16 31⁄4
4.29 15.91
1 1
3
Polyurethane Bellows
Round
Rectangular
Strong, lightweight bellows are heat sealed to keep out moisture and contaminants. There are no stitches or glue that could fail. Color is black. They have high resistance to ozone, chemicals, gasoline, kerosene and most other aliphatic petroleum products, plus excellent resistance to ultraviolet and gamma rays. The bellows have high abrasion resistance and tensile strength. Temperature range is -60 to +225 degree Fahrenheit. Round thickness is .010". Round bellows have 1⁄2" cuffs that may be secured with standard hose clamps. Available in 12" and 24" extended lengths that compress to 1" and 2" respectively. Square/rectangular thickness is .020". Square bellows have square ends without cuffs and are available in 12" and 24" extended length that compresses to 1- 1⁄2" and 3" respectively. 12"
24"
Item No.
Item No.
Round BW-101 BW-102 BW-103 BW-104 BW-105 BW-107 BW-108 —
— BW-112 — BW-114 BW-115 — BW-118 BW-119
ID
OD
Pack Qty.
1
21⁄2 23⁄4 3 31⁄4 31⁄2 4 41⁄2 5
1 1 1 1 1 1 1 1
⁄2 ⁄4 1 11⁄4 11⁄2 2 21⁄2 3 3
12"
24"
Item No.
Item No.
Square/Rectangular — BW-131 — BW-132 — BW-136*
ID
OD
Pack Qty.
1x1 21⁄2 x 21⁄2 7x5
3x3 41⁄2 x 41⁄2 9x7
1 1 1
*Rectangular
SAE 841 61⁄2" Lengths These oil-filled, powdered metal, bronze bars are produced to ASTM standards for consistent precision, quality and uniformity. Bars are vacuum impregnated with non-detergent SAE 30 oil to provide excellent lubrication while being corrosion resistant. The O.D. is oversized and the I.D. is undersized to allow for finishing to listed dimensions. Application temperature range is 10 to 220 degree Fahrenheit. Item No.
Cored BNT-1000 BNT-1001 BNT-1002 BNT-1003 BNT-1004 BNT-1005 BNT-1006 BNT-1007 BNT-1008 BNT-1009 BNT-1010 BNT-1011 BNT-1012 BNT-1013 BNT-1014 BNT-1015 BNT-1016 BNT-1017 BNT-1018 BNT-1019
906
ID 1
⁄2 ⁄2 ⁄2 1 ⁄2 5 ⁄8 3 ⁄4 3 ⁄4 3 ⁄4 1 1 1 1 1 11⁄4 11⁄4 11⁄2 11⁄2 2 21⁄2 3 1 1
OD
1 11⁄8 11⁄4 11⁄2 1 11⁄4 11⁄2 13⁄4 11⁄2 15⁄8 13⁄4 2 3 13⁄4 2 2 21⁄2 23⁄4 31⁄2 4
Pack Qty.
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Item No.
ID
Solid BNT-1020* BNT-1021** BNT-1022 BNT-1023 BNT-1024 BNT-1025 BNT-1026 BNT-1027 BNT-1028 BNT-1029 BNT-1030 BNT-1031 BNT-1032 BNT-1033 BNT-1034 BNT-1035 BNT-1036 BNT-1037
— — — — — — — — — — — — — — — — — —
*2 inch lengths **3 inch lengths
OD 1
⁄4 ⁄8 ⁄2 5 ⁄8 3 ⁄4 7 ⁄8 1 11⁄8 11⁄4 13⁄8 11⁄2 15⁄8 13⁄4 2 21⁄4 21⁄2 3 4 3 1
Pack Qty.
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
CAM FOLLOWERS, BEARINGS & THRUST WASHERS Self-lubricating cam follower provides continuous, dependable lubrication for the life of the unit. heat-treated steel roller with machined lubrication reservoirs are pre-filled with specially developed lube mixtures. Lubrication penetrates through a porous inner sintered bronze bushing by capillary action. Particularly well suited for applications with light to moderate loads operating at medium to higher speeds. Frequently used in food processing, farm and construction, machine tools, metal-working and packaging. Can be used in high humidity applications, or where equipment is subject to frequent "wash downs". s s s s
Load Factor Information rpm Unit Load psi Slow and Intermittent 4,000 Lbs. 150 to 300 rpm 2,000 Lbs. 300 to 600 rpm 600 Lbs. 600 to 900 rpm 400 Lbs. 900 to 1,200 rpm 300 Lbs. Example: NCF-40 Cam Follower at 800 rpm= .391 (load factor) x 400 Lbs. = 156.4 Lbs. Capacity
Bronze bushing bearing Reduces maintenance costs due to simplified design Interchangeable with standard types of needle roller bearings Ambient temperature of +40 degrees Fahrenheit to +150 degrees Fahrenheit
Stud Type
Yoke Type
B
D
1/32
E
D C
G A
C F
Item No.
NCF-5 NCF-10 NCF-15 NCF-20 NCF-25 NCF-30 NCF-35 NCF-40 NCF-45 NCF-50 NCF-55 NCF-60 NCF-65 NCF-70
Size 1
⁄2 ⁄8 ⁄16 3 ⁄4 7 ⁄8 1 11⁄8 11⁄4 13⁄8 11⁄2 15⁄8 13⁄4 17⁄8 2 5
11
+.000 -.001 A
.500 .625 .6875 .750 .875 1.00 1.125 1.250 1.375 1.500 1.625 1.750 1.875 2.000
+.000 -.005 B
+.001 -.000 C
+.010 -.010 D
+.030 -.030 E
Thread F
Hex Key Across Flats G
.375 .190 .625 .250 10-32 .4375 .250 .750 .312 1⁄4-28 .4375 .250 .750 .312 1⁄4-28 .500 .375 .875 .375 3⁄8-24 .500 .375 .875 .375 3⁄8-24 .625 .4375 1.000 .500 7⁄16-20 .625 .4375 1.000 .500 7⁄16-20 .750 .500 1.250 .625 1⁄2-20 .750 .500 1.250 .625 1⁄2-20 .875 .625 1.500 .750 5⁄8-18 .875 .625 1.500 .750 5⁄8-18 1.000 .750 1.750 .875 3⁄4-16 1.000 .750 1.750 .875 3⁄4-16 1.125 .875 2.000 1.000 7⁄8-14
1
⁄8 ⁄8 ⁄8 3 ⁄16 3 ⁄16 1 ⁄4 1 ⁄4 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 3 ⁄8 3 ⁄8 3 ⁄8 1 1
A E
B
Load Pack Factor Qty.
.070 .097 .097 .164 .164 .250 .250 .391 .391 .544 .544 .700 .700 .984
1 1 1 1 1 1 1 1 1 1 1 1 1 1
Item No.
NCF-105 NCF-110 NCF-115 NCF-120 NCF-125 NCF-130 NCF-135 NCF-140 NCF-145 NCF-150 NCF-155
Size 3
⁄4 7 ⁄8 1 11⁄8 11⁄4 13⁄8 11⁄2 15⁄8 13⁄4 17⁄8 2
+.000 -.001 A
+.002 -.004 B
+.000 -.005 C
+.005 -.010 D
.750 .875 1.000 1.125 1.250 1.375 1.500 1.625 1.750 1.875 2.000
.250 .250 .3125 .3125 .375 .375 .4375 .4375 .500 .500 .625
.500 .5625 .500 .5625 .625 .6875 .625 .6875 .750 .8125 .750 .8125 .875 .9375 .875 .9375 1.000 1.0625 1.000 1.0625 1.125 1.3125
E 5
⁄8 5 ⁄8 11 ⁄16 11 ⁄16 7 ⁄8 7 ⁄8 1 1 11⁄16 11⁄16 13⁄8
Shaft Dia.
Load Factor
Pack Qty.
.2497 .2497 .3122 .3122 .3747 .3747 .4372 .4372 .4997 .4997 .6247
.190 .190 .250 .250 .390 .390 .510 .510 .650 .650 .928
1 1 1 1 1 1 1 1 1 1 1
Note: Load factor information available in above table
Note: Load factor information available in above table
Self-Lubricating Metal Backed Bearings Item No.
Fiberglide® bearings are designed to carry higher loads with improved wear life. Fiberglide® bearings are unique in their ability to resist cold flow under extremely high load because the monofilament fibers have a tensile strength approximately 25 times greater than straight PTFE resins. Fiberglide® bearings are completely self-lubricating and normally run dry. Operating Fiberglide® bearings are recommended where low surface speeds are combined with high loads.
RBC-490 RBC-500 RBC-510 RBC-520 RBC-530 RBC-540 RBC-550 RBC-560 RBC-570 RBC-580 RBC-590 RBC-600 RBC-610 RBC-620 RBC-630 RBC-640 RBC-650 RBC-660 RBC-670 RBC-680 RBC-690 RBC-700 RBC-720 RBC-750
Max. Shaft Diameter
0.375 0.375 0.5 0.5 0.5 0.625 0.625 0.625 0.75 0.75 0.75 0.875 1 1 1 1 1.25 1.25 1.25 1.5 2 12 16 22
Housing Bore Min.
0.468 0.468 0.593 0.593 0.593 0.718 0.718 0.718 0.8745 0.8745 0.8745 0.9995 1.1245 1.1245 1.1245 1.1245 1.4055 1.4055 1.4055 1.6555 2.1875 14 18 25
Max.
0.469 0.469 0.594 0.594 0.594 0.719 0.719 0.719 0.8755 0.8755 0.8755 1.0005 1.1255 1.1255 1.1255 1.1255 1.4065 1.4065 1.4065 1.6565 2.1885 14.018 18.018 25.021
Bearing Length 3
⁄8 ⁄2 ⁄2 5 ⁄8 3 ⁄4 5 ⁄8 3 ⁄4 1 1 ⁄2 3 ⁄4 1 1 1 ⁄2 3 ⁄4 1 11⁄4 3 ⁄4 1 11⁄4 11⁄2 2 12 12 15 1 1
Pack Qty.
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Self-Lubricating Metal Backed Thrust Washers
Item No.
Max. Shaft Diameter
Outside Diameter
Thickness
Pack Qty.
RBC-760 RBC-770 RBC-780 RBC-790 RBC-800 RBC-810 RBC-820 RBC-830 RBC-840
0.375 0.5 0.625 0.75 0.875 1 1.25 1.5 2
0.75 1 1.25 1.5 1.75 2 2.25 2.625 3.25
0.058 0.058 0.058 0.058 0.058 0.058 0.058 0.058 0.058
1 1 1 1 1 1 1 1 1
Fiberglide® series thrust bearings offer an economical approach to obtaining self-lubrication where high loads are encountered. They are comprised of zincplated mild steel with Fiberglide laminated to one face. These bearings are recommended for use where metal backing is preferred. These bearings are self-lubricating and tolerate a compressive strength of 38,000 psi with operating temperature range of -320 degrees Fahrenheit to 300 degrees Fahrenheit. Coefficient of friction can be obtained as low as 0.03 with no added lubricants.
907
RADIAL - THRUST CAM FOLLOWERS These radial/thrust bearings are capable of handling combined radial and thrust loads. They are tightly sealed for use in high moisture or dusty environments. They also run at much higher speeds than needle bearings. Made of steel. Flanged Stud Type Guidance in two planes for thrust loads. Item No.
CCF-260 CCF-265 CCF-270 CCF-275 CCF-280 CCF-285
Dynamic Load A
B
1.50 1.75 2.00 2.25 2.50 3.00
C
1.188 1.188 1.688 1.688 1.688 2.000
D
2.188 2.438 2.688 2.938 3.188 3.938
K
.344 .344 .594 .594 .594 .594
L
.625 .750 .875 .875 1.000 1.250
1.50 1.75 2.00 2.00 2.25 2.50
M
N
R
5
⁄8-18 .750 .875 3⁄4-16 1.125 7⁄8-14 1.125 7⁄8-14 1.500 1-14 1.750 11⁄4-12
Radial
Thrust
Pack Qty.
2,750 2,750 3,820 3,820 5,180 14,300
1,700 1,700 2,380 2,380 3,185 5,790
1 1 1 1 1 1
S 5
.750 1.000 1.000 1.000 1.250 1.750
⁄16 ⁄16 ⁄16 5 ⁄16 — 1 ⁄2 5 5
Note: Dynamic load rating based on 500 hours L10 life at 33 1⁄3 rpm
Flanged Roller
F
G
C D
A
B
20°
Dynamic Load
Item No.
A
B
C
D
F
G
Radial
Thrust
Pack Qty.
CCF-945 CCF-950
2.500 3.000
.750 1.000
1.562 1.812
1.500 1.750
3.187 3.937
.500 .594
7,630 20,000
4,570 12,000
1 1
V-Groove Stud Type
For V-track applications. Item No.
CCF-305 CCF-310
Dynamic Load A
B
2.50 3.50
F
1.313 1.688
G
1.50 2.25
K
.688 .875
L
.750 .875
1.75 2.00
M
.875 1.125
N
R
3
⁄4-16 ⁄8-14
S 5
1.00 1.00
7
⁄16 ⁄16
5
Radial
Thrust
Pack Qty.
2,750 5,180
1,700 3,185
1 1
1
Note: Dynamic load rating based on 500 hours L10 life at 33 ⁄3 rpm
V-Groove Roller C D 90°
E
A
B
G
Dynamic Load
Item No.
A
B
C
D
E
G
Radial
Thrust
Pack Qty.
CCF-955 CCF-960
2.5 3.0
.750 1.000
1.562 1.612
1.50 1.75
3.750 4.500
.625 .750
7,630 12,660
4,570 12,000
1 1
Plain Stud Type
Ideal for simple radial loads or to handle side loads. Item No.
CCF-205 CCF-210 CCF-215 CCF-225 CCF-230 CCF-240
+.000/.001 A
1.50 1.75 2.00 2.50 3.00 4.00
B
1.188 1.188 1.688 1.688 2.000 2.000
+.000/.001 K
.625 .750 .875 1.000 1.250 1.250
Dynamic Load L
M
1.50 1.75 2.00 2.25 2.50 2.75
.750 .875 1.125 1.500 1.750 1.750
N 5
⁄8-18 ⁄4-16 ⁄8-14 1-14 11⁄4-12 11⁄4-12 3 7
R
S 5
.750 1.000 1.000 1.250 1.750 1.750
⁄16 ⁄16 ⁄16 1 ⁄2 1 ⁄2 1 ⁄2
5 5
Radial
Thrust
Pack Qty.
2,750 2,750 3,820 5,180 14,300 14,300
1,700 1,700 2,380 3,185 5,790 5,790
1 1 1 1 1 1
Note: Dynamic load rating based on 500 hours L10 life at 33 1⁄3 rpm
Plain Roller
908
Dynamic Load
Item No.
A
B
C
D
Radial
Thrust
Pack Qty.
CCF-935 CCF-940
2.500 3.000
.750 1.000
1.562 1.812
1.50 1.75
7,630 20,000
4,570 12,000
1 1
CAM FOLLOWERS Regular Duty Steel - The inner and outer race are made of high carbon chrome bearing steel through hardened and ground. The studs are low carbon steel. The steel type are slotted. Regular Duty Stainless Steel - Made of 440C stainless steel. Extends your bearing life and reduces maintenance cost. They use food grade lubricant. The stainless type have a hex socket. Heavy Duty Steel - Similar to the regular duty but the studs are thicker. The heavy duty steel type have a hex socket. Heavy Duty Stainless Steel - Made of 440C stainless steel. Similar to the regular duty stainless steel. The stainless type have a hex socket. Stud Type Followers Steel or Stainless Steel
Regular Duty Steel Item No.
Static Rating Lbs.
Regular Duty CCF-5 790 CCF-10 1,215 CCF-15 2,065 CCF-20 2,065 CCF-25 2,065 CCF-30 3,060 CCF-35 4,250 CCF-40 4,250 CCF-45 5,640 CCF-50 5,640 CCF-55 7,920 CCF-60 7,920 CCF-65 10,570 CCF-70 10,570 CCF-75 16,450 CCF-80 24,910 Heavy Duty CCF-500 1,580 CCF-505 2,480 CCF-510 4,130 CCF-515 4,130 CCF-520 6,120 CCF-525 8,500 CCF-530 8,500 CCF-535 11,280 CCF-540 15,840 CCF-545 21,140 CCF-550 21,140 CCF-555 32,900
Heavy Duty
Stainless Dynamic Rating Lbs.
Item No.
Static Rating Lbs.
Dynamic Rating Lbs.
680 995 1,660 1,660 2,225 2,225 3,930 3,930 4,840 4,840 6,385 6,385 8,090 8,090 11,720 15,720
CCF-350 CCF-355 CCF-360 — CCF-370 — CCF-380 — CCF-390 — CCF-400 — CCF-410 — — —
300 600 1,500 — 1,800 — 2,300 — 4,000 — 6,000 — 8,200 — — —
610 860 1,490 — 2,000 — 3,530 — 4,350 — 5,730 — 7,270 — — —
680 955 1,660 1,660 2,225 3,930 3,930 4,840 6,385 8,090 8,090 11,720
CCF-965 CCF-970 CCF-975 — CCF-980 CCF-985 — CCF-990 CCF-995 CCF-1000 — —
1,106 1,736 2,891 — 4,284 5,950 — 7,896 11,088 16,200 — —
544 796 1,328 — 1,780 3,144 — 3,872 5,108 7,270 — —
Size 1
⁄2 ⁄8 ⁄4 7 ⁄8 1 11⁄8 11⁄4 13⁄8 11⁄2 15⁄8 13⁄4 17⁄8 2 21⁄4 21⁄2 3 5 3
1
⁄2 ⁄8 ⁄4 7 ⁄8 1 11⁄4 13⁄8 11⁄2 13⁄4 2 21⁄4 21⁄2 5 3
+.000 -.001 A
+.000 -.005 B
+.001 -.000 C
+.010 -.010 D
E
F
G
.500 .625 .750 .875 1.000 1.125 1.250 1.375 1.500 1.625 1.750 1.875 2.000 2.250 2.500 3.000
.375 .438 .500 .500 .625 .625 .750 .750 .875 .875 1.000 1.000 1.250 1.250 1.500 1.750
.190 .250 .375 .375 .438 .438 .500 .500 .625 .625 .750 .750 .875 .875 1.000 1.250
.625 .750 .875 .875 1.000 1.000 1.250 1.250 1.500 1.500 1.750 1.750 2.000 2.000 2.250 2.500
.250 .312 .375 .375 .500 .500 .625 .625 .750 .750 .875 .875 1.000 1.000 1.125 1.250
10-32 1 ⁄4-28 3 ⁄8-24 3 ⁄8-24 7 ⁄16-20 7 ⁄16-20 1 ⁄2-20 1 ⁄2-20 5 ⁄8-18 5 ⁄8-18 3 ⁄4-16 3 ⁄4-16 7 ⁄8-14 7 ⁄8-14 1-14 11⁄4-12
— — 1 ⁄4 1 ⁄4 1 ⁄4 1 ⁄4 5 ⁄16 5 ⁄16 3 ⁄8 3 ⁄8 7 ⁄16 7 ⁄16 1 ⁄2 1 ⁄2 9 ⁄16 5 ⁄8
.500 .625 .750 .875 1.000 1.250 1.375 1.500 1.750 2.000 2.250 2.500
.375 .438 .500 .500 .625 .750 .750 .875 1.000 1.250 1.250 1.500
.250 .313 .438 .438 .625 .750 .750 .875 1.000 1.125 1.125 1.250
.625 .750 .875 .875 1.000 1.250 1.250 1.500 1.750 2.000 2.000 2.250
.250 .312 .375 .375 .500 .625 .625 .750 .875 1.000 1.000 1.125
⁄4-28 ⁄16-24 ⁄16-20 7 ⁄16-20 5 ⁄8-18 3 ⁄4-16 3 ⁄4-16 7 ⁄8-14 1-14 11⁄8-12 11⁄8-12 11⁄4-12
1
7
Pack Qty.
— — ⁄32 3 ⁄32 3 ⁄32 3 ⁄32 3 ⁄32 3 ⁄32 3 ⁄32 3 ⁄32 3 ⁄32 3 ⁄32 1 ⁄8 1 ⁄8 1 ⁄8 1 ⁄8
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
— — ⁄32 3 ⁄32 3 ⁄32 3 ⁄32 3 ⁄32 3 ⁄32 3 ⁄32 1 ⁄8 1 ⁄8 1 ⁄8
1 1 1 1 1 1 1 1 1 1 1 1
3
— — 1 ⁄4 1 ⁄4 1 ⁄4 5 ⁄16 5 ⁄16 3 ⁄8 7 ⁄16 1 ⁄2 1 ⁄2 9 ⁄16
5
H
3
Stud Type Followers - Crown Steel
Recommended where variations in dimensions of alignment of the tracks or cam might cause excessive angular loading. It reduces thrust on the rollers and wear and aids reliability. Load Rating
Item No.
Crown Radius
A
B
C
D
E
F
G
H
Dynamic
Static
Pack Qty.
CCF-805 CCF-810 CCF-815 CCF-820 CCF-825 CCF-830 CCF-835 CCF-840 CCF-845 CCF-850 CCF-855 CCF-860 CCF-865 CCF-870
7 8 10 10 12 12 14 14 20 20 20 20 24 24
.500 .625 .750 .875 1.000 1.125 1.250 1.375 1.500 1.625 1.750 1.875 2.000 2.250
.375 .438 .500 .500 .625 .625 .750 .750 .875 .875 1.000 1.000 1.250 1.250
.190 .250 .375 .375 .438 .438 .500 .500 .625 .625 .750 .750 .875 .875
.625 .625 .750 .750 1.000 1.000 1.250 1.250 1.500 1.500 1.750 1.750 2.000 2.000
.250 .312 .375 .375 .500 .500 .625 .625 .750 .750 .875 .875 1.000 1.000
10-32 1 ⁄4-28 3 ⁄8-24 3 ⁄8-24 7 ⁄16-20 7 ⁄16-20 1 ⁄2-20 1 ⁄2-20 5 ⁄8-18 5 ⁄8-18 3 ⁄4-16 3 ⁄4-16 7 ⁄8-14 7 ⁄8-14
— — 1 ⁄4 1 ⁄4 1 ⁄4 1 ⁄4 5 ⁄16 5 ⁄16 3 ⁄8 3 ⁄8 7 ⁄16 7 ⁄16 1 ⁄2 1 ⁄2
— — 3 ⁄32 3 ⁄32 3 ⁄32 3 ⁄32 3 ⁄32 3 ⁄32 3 ⁄32 3 ⁄32 3 ⁄32 3 ⁄32 1 ⁄8 1 ⁄8
680 995 1,660 1,660 2,225 2,225 3,930 3,930 4,840 4,840 6,385 6,385 8,090 8,090
790 1,215 2,065 2,065 3,060 3,060 4,250 4,250 5,640 5,640 7,920 7,920 10,570 10,570
1 1 1 1 1 1 1 1 1 1 1 1 1 1
909
CAM FOLLOWERS Yoke Type Rollers Steel or Stainless Steel
Can support heavier loads because stud deflection is not a factor. Bearings are sealed. Steel
Stainless
Item No.
Static Rating Lbs.
Dynamic Rating Lbs.
Item No.
Static Rating Lbs.
Dynamic Rating Lbs.
CCF-105 CCF-110 CCF-115 CCF-120 CCF-125 CCF-130 CCF-135 CCF-145 CCF-150 CCF-155 CCF-160 CCF-165 CCF-170
4,130 4,130 6,120 6,120 8,500 8,500 11,280 15,840 15,840 21,140 21,140 32,900 49,820
1,660 1,660 2,225 2,225 3,930 3,930 4,840 6,385 6,385 8,090 8,090 11,720 15,720
CCF-430 — CCF-440 — CCF-450 — CCF-460 CCF-470 — — — — —
2,100 — 5,000 — 7,700 — 11,200 14,800 — — — — —
1,490 — 2,000 — 3,903 — 4,350 5,730 — — — — —
Size 3
⁄4 ⁄8 1 11⁄8 11⁄4 13⁄8 11⁄2 13⁄4 17⁄8 2 21⁄4 21⁄2 3 7
+.000 -.001 A
+.0002 -.0004 B
+.000 -.005 C
+.005 -.010 D
.750 .875 1.000 1.1250 1.250 1.375 1.500 1.750 1.875 2.000 2.250 2.500 3.000
.2500 .2500 .3125 .3125 .3750 .3750 .4375 .5000 .5000 .6250 .6250 .7500 1.0000
.500 .500 .625 .625 .750 .750 .875 1.000 1.000 1.250 1.250 1.500 1.750
.5625 .5625 .6875 .6875 .8125 .8125 .9375 1.0625 1.0625 1.3125 1.3125 1.5625 1.8125
Oil Hole Dia.
E
Pack Qty.
3
5
⁄8 ⁄8 ⁄32 25 ⁄32 1 1 11⁄8 11⁄4 11⁄4 11⁄2 11⁄2 13⁄4 21⁄4
⁄32 ⁄32 ⁄32 3 ⁄32 3 ⁄32 3 ⁄32 3 ⁄32 3 ⁄32 3 ⁄32 3 ⁄32 3 ⁄32 1 ⁄8 1 ⁄8
1 1 1 1 1 1 1 1 1 1 1 1 1
3
5
3
25
Yoke Type Rollers - Crown Steel
Item No.
Crown Radius
A
B
C
D
CCF-875 CCF-880 CCF-885 CCF-890 CCF-895 CCF-900 CCF-905 CCF-910 CCF-915 CCF-920 CCF-925 CCF-930
10 10 12 12 14 14 20 20 20 20 24 24
.750 .875 1.000 1.125 1.250 1.375 1.500 1.625 1.750 1.875 2.000 2.250
.2500 .2500 .3125 .3125 .3750 .3750 .4375 .4375 .5000 .5000 .6250 .6250
.500 .500 .625 .625 .750 .750 .875 .875 1.000 1.000 1.250 1.250
.562 .562 .687 .687 .812 .812 .937 .937 1.062 1.062 1.312 1.312
Load Rating
Oil Hole Diameter
E
3
5
⁄8 5 ⁄8 23 ⁄32 23 ⁄32 1 1 11⁄8 11⁄8 11⁄4 11⁄4 11⁄2 11⁄2
⁄32 3 ⁄32 3 ⁄32 3 ⁄32 3 ⁄32 3 ⁄32 3 ⁄32 3 ⁄32 3 ⁄32 3 ⁄32 3 ⁄32 3 ⁄32
Dynamic
Static
Pack Qty.
1,660 1,660 2,225 2,225 3,930 3,930 4,840 4,840 6,385 6,385 8,090 8,090
4,130 4,130 6,120 6,120 8,500 8,500 11,280 11,280 15,840 15,840 21,140 21,140
1 1 1 1 1 1 1 1 1 1 1 1
Needle Bearing Cam Follower Sealed Chrome Plated B
D 1/32
H
G
E
A
J C
F
Item No.
+.000 -.001 A
+.000 -.005 B
+.001 -.000 C
+.010 -.010 D
E
F
G
H
Dynamic Ratings Lbs.
Static Ratings Lbs.
Pack Qty.
CCF-1245 CCF-1250 CCF-1255 CCF-1260 CCF-1265 CCF-1270 CCF-1275 CCF-1280
.500 .625 .750 1.000 1.250 1.500 1.750 2.000
.375 .438 .500 .625 .750 .875 1.000 1.250
.190 .250 .375 .438 .500 .625 .750 .875
.625 .750 .875 1.000 1.250 1.500 1.750 2.000
.250 .312 .375 .500 .625 .750 .875 1.000
10-32 1 ⁄4-28 3 ⁄8-24 7 ⁄16-20 1 ⁄2-20 5 ⁄8-18 3 ⁄4-16 7 ⁄8-14
— — 1 ⁄4 1 ⁄4 5 ⁄16 3 ⁄8 7 ⁄16 1 ⁄2
— — 3 ⁄32 3 ⁄32 3 ⁄32 3 ⁄32 3 ⁄32 1 ⁄8
680 955 1,660 2,225 3,930 4,840 6,385 8,090
790 1,215 2,065 3,060 4,250 5,640 7,920 10,570
1 1 1 1 1 1 1 1
910
CAM FOLLOWERS The RBC Roller® was developed for customers needing a high degree of assurance of long cam follower life. The design incorporates two paths of cylindrical rollers that offer stable outer ring support. With the increased size of the rollers, the RBC Roller® has increased dynamic capacity and fatigue life offering at least twice, and up to five times the fatigue life of the conventional needle roller bearing cam followers. Contacting lip seals are a standard feature of the RBC Roller®. These seals provide positive exclusion of solid and liquid contaminates, and excellent lubricant retention. With large grease storage and the contacting lip seals the RBC Roller® is a true maintenance free cam follower. The RBC Roller® also offers higher speed capacity than the needle roller bearing cam follower and is interchangeable. Long Life Cam Followers
C H OD
G
E F
1/32
D
B Item No.
RBC-10 RBC-20 RBC-30 RBC-40 RBC-50 RBC-60 RBC-70 RBC-80 RBC-90 RBC-100 RBC-110 RBC-120 RBC-130 RBC-140 RBC-150 RBC-160
+.000/-.001 OD
1.000 1.125 1.250 1.375 1.500 1.625 1.750 1.875 2.000 2.250 2.500 2.750 3.000 3.250 3.500 4
+.000/-.005 B
.625 .625 .750 .750 .875 .875 1.000 1.000 1.250 1.250 1.500 1.500 1.750 1.750 2.000 2.250
+.001/-.000 C
D
.4375 .4375 .5000 .5000 .6250 .6250 .7500 .7500 .8750 .8750 1.0000 1.0000 1.2500 1.2500 1.3750 1.5000
E
1.000 1.000 1.25 1.25 1.500 1.500 1.750 1.750 2.000 2.000 2.250 2.250 2.500 2.500 2.750 3.500
F
.500 .500 .625 .625 .750 .750 1.000 1.000 1.125 1.125 1.250 1.500 1.500 1.500 1.625 1.750
G
.500 .500 .625 .625 .750 .750 .875 .875 1.000 1.000 1.125 1.125 1.250 1.250 1.375 1.500
H
7
⁄16-20 ⁄ -20 ⁄ -20 ⁄ -20 ⁄ -18 ⁄ -18 ⁄ -16 ⁄ -16 ⁄ -14 ⁄ -14 11⁄4 11⁄4-12 1 1 ⁄4-12 11⁄4-12 13⁄8-12 11⁄2-12 7
16 1 2 1 2 5 8 5 8 3 4 3 4 7 8 7 8
1
⁄4 ⁄4 ⁄4 1 ⁄4 5 ⁄16 5 ⁄16 5 ⁄16 5 ⁄16 7 ⁄16 7 ⁄16 1 ⁄2 1 ⁄2 5 ⁄8 5 ⁄8 5 ⁄8 3 ⁄4 1 1
Dynamic Static Ratings Lbs. Ratings Lbs.
3,000 3,000 4,100 4,100 6,200 6,200 8,200 8,200 12,400 12,400 16,800 16,800 28,900 28,900 36,100 45,600
3,200 3,200 4,300 4,300 7,000 7,000 10,500 10,500 17,200 17,200 22,800 22,800 39,100 39,100 53,000 68,000
Max. Load
Speed Limit
Pack Qty.
1,400 1,700 1,500 1,850 2,400 2,800 3,150 3,800 5,500 7,000 9,100 10,900 15,000 17,800 21,200 23,700
9,400 9,400 7,500 7,500 6,200 6,200 4,700 4,700 4,100 4,100 3,700 3,700 3,100 3,100 2,900 2,600
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Long Life Yoke Rollers
D C
OD
ID
E
Item No.
+.000/.001 OD
ID (Min.) ID (Max.)
+.000/.005 C
+.005/.010 D
E
Dynamic Ratings Lbs.
Static Ratings Lbs.
Max. Load
Speed Limit
Pack Qty.
RBC-170 RBC-180 RBC-190 RBC-200 RBC-210 RBC-220 RBC-230 RBC-240 RBC-250 RBC-260 RBC-270 RBC-280 RBC-290 RBC-300 RBC-310 RBC-320
1.000 1.125 1.250 1.375 1.500 1.625 1.750 1.875 2.000 2.250 2.500 2.750 3.000 3.250 3.500 4.000
.3121 .3121 .3746 .3746 .4371 .4371 .4996 .4996 .6246 .6246 .7496 .7496 .9995 .9995 1.1245 1.2495
.625 .625 .750 .750 .875 .875 1.000 1.000 1.250 1.250 1.500 1.500 1.750 1.750 2.000 2.250
.6925 .6925 .8125 .8125 .9375 .9375 1.0625 1.0625 1.3125 1.3125 1.5625 1.5625 1.8125 1.8125 2.0625 2.3125
.500 .500 .625 .625 .750 .750 1.000 1.000 1.125 1.125 1.250 1.250 1.500 1.500 1.625 1.750
3,000 3,000 4,100 4,100 6,200 6,200 8,200 8,200 12,400 12,400 16,800 16,800 28,900 28,900 36,100 45,600
3,200 3,200 4,300 4,300 7,000 7,000 10,500 10,500 17,200 17,200 22,800 22,800 39,100 39,100 53,000 68,000
1,400 1,700 1,500 1,850 2,400 2,800 3,150 3,800 5,500 7,000 9,100 10,900 15,000 17,800 21,200 23,700
9,400 9,400 7,500 7,500 6,200 6,200 4,700 4,700 4,100 4,100 3,700 3,700 3,100 3,100 2,900 2,600
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
.3127 .3127 .3752 .3752 .4377 .4377 .5002 .5002 .6252 .6252 .7502 .7502 1.0001 1.0001 1.1251 1.2501
Polycoated bearings can be used for standard and specialized applications where noise reduction, reduced wear and non-marking are important factors in operations. Cam Yoke Rollers Sealed With Cast Urethane Cover Shore 80 A
Needle Bearing Cam Followers Sealed With Cast Urethane Cover Shore 80 A B
D
1/32
D C
G H E
F
A
F
C
Item No.
CCF-1180 CCF-1185 CCF-1190 CCF-1195 CCF-1200 CCF-1205 CCF-1210
Size 3
⁄4 1 11⁄4 11⁄2 13⁄4 2 21⁄4
+.005 -.005 A
.750 1.000 1.250 1.500 1.750 2.000 2.250
+.005 -.005 B
.375 .500 .625 .750 .875 1.000 1.250
+.001 -.000 C
.190 .375 .4375 .500 .625 .750 .875
+.010 -.010 D
.625 .875 1.000 1.250 1.500 1.750 2.000
B E
A
E
.250 .375 .500 .625 .750 .875 1.000
F
10-32 3 ⁄8-24 7 ⁄16-20 1 ⁄2-20 5 ⁄8-18 3 ⁄4-16 7 ⁄8-14
G
— 1 ⁄4 1 ⁄4 5 ⁄16 3 ⁄8 7 ⁄16 1 ⁄2
H
— ⁄32 3 ⁄32 3 ⁄32 3 ⁄32 3 ⁄32 1 ⁄8 3
J
— ⁄16 3 ⁄16 3 ⁄16 3 ⁄16 3 ⁄16 3 ⁄16 3
J
Pack Qty.
1 1 1 1 1 1 1
Item No.
CCF-1215 CCF-1220 CCF-1225 CCF-1230 CCF-1235 CCF-1240
Size
+.005 -.005 A
+.0002 -.0004 B
+.005 -.005 C
+.005 -.010 D
1 11⁄4 11⁄2 13⁄4 2 21⁄4
1.000 1.250 1.500 1.750 2.000 2.250
.250 .3125 .375 .4375 .500 .625
.500 .625 .750 .875 1.000 1.250
.5625 .6875 .8125 .9375 1.0625 1.3125
Flange OD Ref. E 5
⁄8 23 ⁄32 1 11⁄8 11⁄4 11⁄2
Oil Hole Dia. F 3
⁄32 3 ⁄32 3 ⁄32 3 ⁄32 3 ⁄32 3 ⁄32
Pack Qty.
1 1 1 1 1 1
911
BRONZE BEARINGS SAE 841 Bronze - Oil Impregnated
ID
These "Oilite type" self lubricating sintered bronze stock bearings have long conformed to ASTM chemical and physical properties, and are the first to include all ASTM standard sizes to all ASTM recommended dimensions and tolerances. After forming, sintering and sizing, the bearings are vacuum impregnated with SAE30 oil that provides lubricant which is metered from the bearing to the shaft during rotation. They will function satisfactorily in temperature ranges of 10 to 220 degrees Fahrenheit. Max P = 2,000, Max V=1,200 and Max PV = 50,000. Ideal for all applications where repeat lubrication is difficult, including all agricultural and industrial machinery and equipment.
OD
ID or OD Size to 1.510 1.511 to 2.510 2.511 to 3.010 3.011 to 4.010 4.011 to 5.010
LENGTH
Item No.
ID
⁄8" ID x 1⁄4" ID Nominal BNT-100 .1270 BNT-101 .1270 BNT-102 .1270 3 ⁄16" ID x 1⁄4" ID Nominal BNT-103 .1895 BNT-104 .1895 BNT-105 .1895 3 ⁄16" ID x 5⁄16" ID Nominal BNT-106 .1895 BNT-107 .1895 BNT-108 .1895 1 ⁄4" ID x 5⁄16" ID Nominal BNT-109 .2520 BNT-110 .2520 BNT-111 .2520 1 ⁄4" ID x 3⁄8" ID Nominal BNT-112 .2520 BNT-113 .2520 BNT-114 .2520 BNT-115 .2520 BNT-116 .2520 BNT-117 .2520 BNT-118 .2520 1 ⁄4" ID x 1⁄2" ID Nominal BNT-119 .2500 BNT-120 .2500 BNT-121 .250 5 ⁄16" ID x 3⁄8" ID Nominal BNT-122 .3145 BNT-123 .3145 BNT-124 .3145 BNT-125 .3145 BNT-126 .3145 5 7 ⁄16" ID x ⁄16" ID Nominal BNT-305 .3125 BNT-306 .3125 BNT-307 .3125 BNT-308 .3125 3 ⁄8" ID x 1⁄2" ID Nominal BNT-127 .3770 BNT-128 .3770 BNT-129 .3770 BNT-130 .3770 BNT-131 .3770 BNT-132 .3770 BNT-133 .3770 BNT-134 .3770 3 ⁄8" ID x 9⁄16" ID Nominal BNT-135 .3770 BNT-136 .3770 BNT-137 .3770 BNT-138 .3770 3 ⁄8" ID x 5⁄8" ID Nominal BNT-139 .3770 BNT-140 .3770 BNT-141 .3770 7 ⁄16" ID x 5⁄8" ID Nominal BNT-142 .4395 BNT-143 .4395 BNT-144 .4395 1 ⁄2" ID x 5⁄8" ID Nominal BNT-145 .5020 BNT-146 .5020 BNT-147 .5020 BNT-148 .5020 BNT-149 .5020 BNT-150 .5020
OD
Lgth.
Pack Qty.
1
912
Item No.
ID
OD
Length Size to 1.495 1.496 to 2.990 2.991 to 4.895
Lgth.
Tolerance ±.005 ±.0075 ±.010
Pack Qty.
1
.2530 .2530 .2530
1
.2530 .2530 .2530
1
.3155 .3155 .3155
1
⁄4 3 ⁄8 1 ⁄2
1 1 1
.3155 .3155 .3155
1
⁄4 1 ⁄2 3 ⁄4
1 1 1
.3780 .3780 .3780 .3780 .3780 .3780 .3780
1
1 1 1 1 1 1 1
⁄8 ⁄4 ⁄8
1 3
⁄4 ⁄8 ⁄2
3 1
⁄4 ⁄8 ⁄2 5 ⁄8 3 ⁄4 7 ⁄8 1 3 1
1 1 1 1 1 1
.5030 .5030 .5030
1
.3780 .3780 .3780 .3780 .3780
1
.4400 .4400 .4400 .4400
1
⁄4 ⁄8 ⁄2 3 ⁄4
1 1 1 1
.5030 .5030 .5030 .5030 .5030 .5030 .5030 .5030
1
1 1 1 1 1 1 1 1
.5655 .5655 .5655 .5655
⁄2 ⁄4 1
3
⁄4 ⁄8 ⁄2 5 ⁄8 3 ⁄4 3 1
3 1
⁄4 ⁄8 ⁄2 5 ⁄8 3 ⁄4 7 ⁄8 1 11⁄4 3 1
1
⁄2 ⁄4 1 11⁄4 3
1 1 1 1 1 1 1 1
1 1 1 1
.6280 .6280 .6280
3
.6280 .6280 .6280
1
⁄2 ⁄4 1
1 1 1
.6280 .6280 .6280 .6280 .6280 .6280
3
1 1 1 1 1 1
⁄8 ⁄2 ⁄4
1 3
3
⁄8 ⁄2 ⁄8 3 ⁄4 1 11⁄4 1 5
1 1 1
⁄2" ID x 3⁄4" ID Nominal BNT-151 .5020 BNT-152 .5020 BNT-153 .5020 BNT-154 .5020 BNT-155 .5020 BNT-156 .5020 9 ⁄16" ID x 3⁄4" ID Nominal BNT-157 .5645 BNT-158 .5645 5 ⁄8" ID x 3⁄4" ID Nominal BNT-159 .6270 BNT-160 .6270 BNT-161 .6270 BNT-162 .6270 BNT-163 .6270 BNT-164 .6270 5 13 ⁄8" ID x ⁄16" ID Nominal BNT-165 .6270 BNT-166 .6270 BNT-167 .6270 5 ⁄8" ID x 7⁄8" ID Nominal BNT-168 .6270 BNT-169 .6270 BNT-170 .6270 BNT-171 .6270 3 ⁄4" ID x 7⁄8" ID Nominal BNT-172 .7520 BNT-173 .7520 BNT-174 .7520 BNT-175 .7520 BNT-176 .7520 3 ⁄4" ID x 1" ID Nominal BNT-177 .7520 BNT-178 .7520 BNT-179 .7520 BNT-180 .7520 BNT-181 .7520 BNT-182 .7520 BNT-183 .7520 BNT-184 .7520 3 ⁄4" ID x 11⁄8" ID Nominal BNT-185 .7520 7 ⁄8" ID x 1" ID Nominal BNT-186 .8770 7 ⁄8" ID x 11⁄8" ID Nominal BNT-187 .8770 BNT-188 .8770 BNT-189 .8770 1 1" ID x 1 ⁄4" ID Nominal BNT-190 1.0030 BNT-191 1.0030 BNT-192 1.0030 BNT-193 1.0030 BNT-194 1.0030 11⁄8" ID x 13⁄8" ID Nominal BNT-195 1.1280 11⁄4" ID x 11⁄2" ID Nominal BNT-196 1.2535 BNT-197 1.2535 BNT-198 1.2535 11⁄2" ID x 13⁄4" ID Nominal BNT-199 1.5040 BNT-200 1.5040 BNT-201 1.5040 2" ID x 21⁄4" ID Nominal BNT-202 2.0040 BNT-203 2.0040 BNT-204 2.0040 3 2" ID x 2 ⁄8" ID Nominal BNT-205 2.0040 BNT-206 2.0040
Tolerance -0.001 -0.0015 -0.002 -0.003 -0.004
3
.7530 .7530 .7530 .7530 .7530 .7530
⁄8 ⁄2 ⁄8 3 ⁄4 1 11⁄4
1 1 1 1 1 1
.7530 .7530
3 ⁄4 11⁄4
1 1
.7530 .7530 .7530 .7530 .7530 .7530
1 5
1
⁄2 ⁄8 ⁄4 7 ⁄8 1 11⁄4 5 3
1 1 1 1 1 1
.8165 .8165 .8165
1
⁄2 ⁄4 1
1 1 1
.8790 .8790 .8790 .8790
1
⁄2 ⁄8 ⁄4 1
1 1 1 1
.8790 .8790 .8790 .8790 .8790
1
1 1 1 1 1
3
5 3
⁄2 ⁄8 ⁄4 1 11⁄4 5 3
1
1.0040 1.0040 1.0040 1.0040 1.0040 1.0040 1.0040 1.0040
⁄2 ⁄8 ⁄4 1 11⁄4 11⁄2 13⁄4 21⁄2
1 1 1 1 1 1 1 1
1.1290
1
1
1.0040
1
1
1.1290 1.1290 1.1290
3
1 1 1
1
⁄2 ⁄4 1 11⁄4 11⁄2
1 1 1 1 1
1.3790
1
1
1.5040 1.5040 1.5040
3
⁄4 1 11⁄2
1 1 1
1.7550 1.7550 1.7550
1 11⁄2 2
1 1 1
2.2550 2.2550 2.2550
1 11⁄2 2
1 1 1
2.3800 2.3800
11⁄2 2
1 1
1.2540 1.2540 1.2540 1.2540 1.2540
5 3
⁄4 1 11⁄4 3
BRONZE BEARINGS Cast Bronze Sleeve Bearings
These cast bronze bearings are machined from continuous cast C93200 (SAE660) bronze for superior quality and performance. The continuous casting process assures a uniform bronze structure throughout the bearing, free from porosity and hard particle inclusions commonly found in other cast processes. These solid bearings are ideal in heavy load applications. Max P = 4,000, Max V = 750 with a Max PV = 75,000. Commonly used in all kinds of agricultural and industrial machinery and equipment. ID
OD ID 3” or Less ±.0010”
LENGTH
Item No.
ID
⁄4" ID x 3⁄8" ID Nominal BNT-207 .2500 BNT-208 .2500 BNT-209 .2500 BNT-210 .2500 BNT-211 .2500 5 ⁄16" ID x 1⁄2" ID Nominal BNT-212 .3125 BNT-213 .3125 BNT-214 .3125 3 ⁄8" ID x 1⁄2" ID Nominal BNT-215 .3750 BNT-216 .3750 BNT-217 .3750 BNT-218 .3750 BNT-219 .3750 3 ⁄8" ID x 9⁄16" ID Nominal BNT-220 .3750 3 ⁄8" ID x 5⁄8" ID Nominal BNT-221 .3750 BNT-222 .3750 7 ⁄16" ID x 9⁄16" ID Nominal BNT-223 .4375 1 ⁄2" ID x 5⁄8" ID Nominal BNT-224 .5000 BNT-225 .5000 BNT-226 .5000 BNT-227 .5000 BNT-228 .5000 BNT-229 .5000 1 3 ⁄2" ID x ⁄4" ID Nominal BNT-230 .5000 BNT-231 .5000 BNT-232 .5000 BNT-233 .5000 BNT-234 .5000 9 ⁄16" ID x 3⁄4" ID Nominal BNT-235 .5625 5 ⁄8" ID x 3⁄4" ID Nominal BNT-236 .6250 BNT-237 .6250 BNT-238 .6250 BNT-239 .6250 BNT-240 .6250 BNT-241 .6250 BNT-242 .6250 5 ⁄8" ID x 13⁄16" ID Nominal BNT-243 .6250 5 ⁄8" ID x 7⁄8" ID Nominal BNT-244 .6250 BNT-245 .6250 5 ⁄8" ID x 1" ID Nominal BNT-246 .6250 BNT-247 .6250 5 ⁄8" ID x 11⁄8" ID Nominal BNT-248 .6250 3 ⁄4" ID x 7⁄8" ID Nominal BNT-249 .7500 BNT-250 .7500 BNT-251 .7500 BNT-252 .7500 3 ⁄4" ID x 1" ID Nominal BNT-253 .7500 BNT-254 .7500 BNT-255 .7500 BNT-256 .7500 BNT-257 .7500 BNT-258 .7500 BNT-259 .7500
OD
Lgth.
Pack Qty.
1
Item No.
Over 3” ±.0015”
ID
Lgth. ±.005”
Concentricity .003” T.I.R
Pack Qty.
OD
Lgth.
1.1250
11⁄2
1
1 1
1 2
1 1
1.1250 1.1250
1 11⁄2
1 1
3
.3750 .3750 .3750 .3750 .3750 .5000 .5000 .5000
3
⁄8 ⁄2 ⁄4 1 1 1 ⁄4 1 3
3
⁄4 1 1 1 ⁄4
1 1 1 1 1 1 1 1
1
⁄2 3 ⁄4 1 11⁄4 11⁄2
1 1 1 1 1
.5625
1
1
.6250 .6250
3
⁄4 1
1 1
.5625
1
1
.6250 .6250 .6250 .6250 .6250 .6250
5
⁄8 ⁄4 1 11⁄4 11⁄2 2
1 1 1 1 1 1
.7500 .7500 .7500 .7500 .7500
3 ⁄4 1 11⁄4 11⁄2 2
1 1 1 1 1
.7500
11⁄4
1
.5000 .5000 .5000 .5000 .5000
.7500 .7500 .7500 .7500 .7500 .7500 .7500
3
1
⁄2 ⁄4 1 11⁄4 11⁄2 13⁄4 2 3
1 1 1 1 1 1 1
.8125
1
1
.8750 .8750
3
⁄4 1
1 1
1 1
1 2
1 1
1.1250
11⁄2
1
.8750 .8750 .875 .8750 1 1 1 1 1 1 1
3
⁄4 1 11⁄4 11⁄2 3
⁄4 1 1 1 ⁄8 11⁄4 11⁄2 2 21⁄4
1 1 1 1 1 1 1 1 1 1 1
⁄4" ID x 11⁄8" ID Nominal BNT-260 .7500 7 ⁄8" ID x 1" ID Nominal BNT-261 .8750 BNT-262 .8750 1" ID x 11⁄8" ID Nominal BNT-263 1 BNT-264 1 1 1" ID x 1 ⁄4" ID Nominal BNT-265 1 BNT-266 1 BNT-267 1 BNT-268 1 BNT-269 1 BNT-270 1 BNT-271 1 BNT-272 1 3 1" ID x 1 ⁄8" ID Nominal BNT-273 1 BNT-274 1 1" ID x 11⁄2" ID Nominal BNT-275 1 BNT-276 1 BNT-277 1 BNT-278 1 11⁄8" ID x 13⁄8" ID Nominal BNT-279 1.1250 BNT-280 1.1250 BNT-281 1.1250 BNT-282 1.1250 11⁄4" ID x 11⁄2" ID Nominal BNT-283 1.2500 BNT-284 1.2500 BNT-285 1.2500 BNT-286 1.2500 5 5 1 ⁄16" ID x 1 ⁄8" ID Nominal BNT-287 1.3125 13⁄8" ID x 15⁄8" ID Nominal BNT-288 1.3750 11⁄2" ID x 13⁄4" ID Nominal BNT-289 1.5000 BNT-290 1.5000 BNT-291 1.5000 1 7 1 ⁄2" ID x 1 ⁄8" ID Nominal BNT-292 1.5000 11⁄2" ID x 2" ID Nominal BNT-293 1.5000 BNT-294 1.5000 BNT-295 1.5000 11⁄2" ID x 21⁄4" ID Nominal BNT-296 1.5000 13⁄4" ID x 2" ID Nominal BNT-297 1.7500 13⁄4" ID x 21⁄4" ID Nominal BNT-298 1.7500 2" ID x 21⁄4" ID Nominal BNT-299 2 2" ID x 23⁄8" ID Nominal BNT-300 2 2" ID x 21⁄2" ID Nominal BNT-301 2 BNT-302 2 21⁄2" ID x 3" ID Nominal BNT-303 2.5000 3" ID x 31⁄2" ID Nominal BNT-304 3
Tolerances OD 3” or Less Over 3” +.002” to +.003” to .003” .005”
3
1.2500 1.2500 1.2500 1.2500 1.2500 1.2500 1.2500 1.2500
⁄4 1 11⁄4 11⁄2 13⁄4 2 21⁄2 3
1 1 1 1 1 1 1 1
1.3750 1.3750
1 11⁄2
1 1
1.5000 1.5000 1.5000 1.5000
11⁄2 2 3 4
1 1 1 1
1.3750 1.3750 1.3750 1.3750
1 13⁄4 2 4
1 1 1 1
1.5000 1.5000 1.5000 1.5000
11⁄2 2 3 4
1 1 1 1
1.6250
21⁄2
1
1.6250
3
1
1.7500 1.7500 1.7500
1 13⁄4 3
1 1 1
1.8750
2
1
2 2 2
1
1 1 1
2 ⁄2 3 4
2.2500
3
1
2
3
1
2.2500
13⁄4
1
2.2500
2
1
2.3750
3
1
2.5000 2.5000
2 3
1 1
3
5
1
3.5000
4
1
913
GAS SPRINGS Fixed Force Gas Springs
B
A C
Patented multi-lobe seal significantly reduces gas leakage, tolerates shaft imperfections, vibrations and wide temperature variations. Body is made of heavy gauge steel and shaft is chromium plated steel. All have M6 x 1.0 threads. Three styles of end fittings are available below to fit these gas springs. Must be ordered separately. Item No.
A
B
C
Compressed Size
Extended Size
P1 Force
Pack Qty.
Item No.
A
B
C
Compressed Size
Extended Size
P1 Force
Pack Qty.
GAS-151 GAS-152 GAS-153 GAS-154 GAS-155 GAS-161 GAS-162 GAS-163 GAS-165 GAS-171 GAS-172 GAS-173 GAS-175 GAS-101 GAS-102 GAS-103 GAS-104 GAS-105 GAS-111
.24 .24 .24 .24 .24 .24 .24 .24 .24 .24 .24 .24 .24 .32 .32 .32 .32 .32 .32
.59 .59 .59 .59 .59 .59 .59 .59 .59 .59 .59 .59 .59 .75 .75 .75 .75 .75 .75
2.00 2.00 2.00 2.00 2.00 3.15 3.15 3.15 3.15 3.50 3.50 3.50 3.50 3.50 3.50 3.50 3.50 3.50 5.00
5.50 5.50 5.50 5.50 5.50 6.45 6.45 6.45 6.45 8.50 8.50 8.50 8.50 8.40 8.40 8.40 8.40 8.40 10.25
7.50 7.50 7.50 7.50 7.50 9.60 9.60 9.60 9.60 12.00 12.00 12.00 12.00 11.90 11.90 11.90 11.90 11.90 15.25
20 40 60 80 100 20 40 60 100 20 40 60 100 20 30 60 90 120 20
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
GAS-112 GAS-113 GAS-114 GAS-115 GAS-121 GAS-122 GAS-123 GAS-124 GAS-125 GAS-131 GAS-132 GAS-133 GAS-134 GAS-135 GAS-141 GAS-142 GAS-143 GAS-144
.32 .32 .32 .32 .32 .32 .32 .32 .32 .32 .32 .32 .32 .32 .39 .39 .39 .39
.75 .75 .75 .75 .75 .75 .75 .75 .75 .75 .75 .75 .75 .75 .87 .87 .87 .87
5.00 5.00 5.00 5.00 6.00 6.00 6.00 6.00 6.00 7.00 7.00 7.00 7.00 7.00 10.00 10.00 10.00 10.00
10.25 10.25 10.25 10.25 11.00 11.00 11.00 11.00 11.00 12.63 12.63 12.63 12.63 12.63 17.80 17.80 17.80 17.80
15.25 15.25 15.25 15.25 17.00 17.00 17.00 17.00 17.00 19.63 19.63 19.63 19.63 19.63 27.80 27.80 27.80 27.80
30 60 90 120 20 30 60 90 120 20 30 60 90 120 100 120 150 200
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Note: P1 force is extended force Length including end fittings (center to center)
Adjustable Force Gas Springs
B
A Thread
D
C E
These adjustable gas springs are the perfect solution for small volume design or replacement applications, as the need to calculate the exact force required is eliminated. Each gas spring is charged at the factory to its maximum force value. Once installed in an application, a simple allen key (included) adjustment can be made to reduce the gas spring force, until the desired application function is reached. Manufactured from specially designed seals, nitrotec finished rods and powder epoxy paint finished tubes for maximum life and service. To order a complete gas spring, select a spring from the table below, then specify which end fittings you need. (Two end fittings per gas spring.) Item No.
A
Cyl. Dia. B
Stroke C
D
E
Supplied Force Lbs.
Thread Size
Pack Qty.
GAS-1 GAS-2 GAS-3 GAS-4 GAS-5 GAS-7
.23 .23 .31 .31 .31 .39
.59 .59 .71 .71 .71 .91
2.36 3.94 3.94 5.91 7.87 11.81
3.94 5.51 6.46 8.43 10.39 13.39
6.30 9.45 10.39 14.33 18.27 25.20
90 90 146 146 146 270
M5 x .8 M5 x .8 M6 x 1.0 M6 x 1.0 M6 x 1.0 M8 x 1.25
1 1 1 1 1 1
Econoloc Gas Springs
E C
Thread
A
D
.87
B
Thread
Spring Loaded Mechanical Lock
Econoloc gas springs eliminate the need for separate safety rods in critical lift-assist applications. They automatically lock when fully extended, protecting the operator from potential injury in the unlikely event of gas spring failure through overload or misuse. The Econoloc is manually released by applying thumb pressure to the designated area of the locking shroud, allowing the gas spring to compress in a controlled manner. A single Econoloc gas spring can be used in conjunction with GAS-3, 4, and 5 listed above. Item No.
A
Cyl. Dia. B
Stroke C
D
E
Supplied Force Lbs.
Thread Size
Pack Qty.
GAS-43 GAS-44 GAS-45
.31 .31 .31
.71 .71 .71
3.94 5.91 7.87
5.47 7.44 9.41
10.39 14.33 18.27
146 146 146
M6 x 1.0 M6 x 1.0 M6 x 1.0
1 1 1
914
FITTINGS, AIR & GAS SPRINGS Gas Springs Mounting Brackets
Gas Springs End Fittings .54
.39 Dia.
.55
F E
5/16-18
J
UNC-2A
Ball Stud
Nylon Eyelet End Fitting
1.50 .25
F
.200 Dia.
1.00
1.13
.73
.078
2.00
Flat Bracket
J
.39 Dia. .75
H
Nylon Ball Joint Assembly
F
L-Bracket
J
All are zinc plated steel designed for gas springs. Item No.
Pack Description Qty.
GAS-301 Ball Stud
1
Item No.
Description
GAS-302 Flat Bracket
Pack Qty.
1
Item No.
GAS-303 L-Bracket
Item No.
.394
Die cast zinc. Pack Qty.
A
.205 .260 .325 .405
-
.210 .265 .330 .410
Fits Cyl. Dia.
E mm
Nylon Eyelet End Fitting GAS-10 .59 6 GAS-12 .71 8 Steel Eyelet End Fitting GAS-14 .91 8 Nylon Ball Joint Assembly GAS-20 .59 — GAS-23 .71 — Steel Ball Joint Assembly GAS-30 .71 — GAS-32 .91 —
A
Item No.
H
1
Gas Springs Fat Blade End Fittings
GAS-211 GAS-212 GAS-213 GAS-214
Steel Ball Joint Assembly
Pack Description Qty.
1 1 1 1
F mm
H
J mm
Internal Thread Size
Pack Qty.
17 21
— —
8 10
M5 x .8 M6 x 1.0
1 1
21
—
10
M8 x 1.25
1
17 17.5
M5 x .8 M8 x 1.25
10 12.5
M5 x .8 M6 x 1.0
1 1
18 30
M8 x 1.25 M8 x 1.25
12 16
M6 x 1.0 M8 x 1.25
1 1
*GAS-14 is steel
Gas Spring Plastic End Fitting
Metal End Fitting
.39 Dia. .39 Dia.
End fittings for gas springs. All are M6 x 1.0 thread. Item No.
GAS-202
Description
Max. P1 (Lbs.)
Pack Qty.
Item No.
Description
Max. P1 (Lbs.)
Pack Qty.
Metal End Fitting
200
1
GAS-201
Plastic End Fitting
150
1
Air Springs Single Convolute Bellows Type Air springs are used in many applications from scissor lifts to presses, compressors and electronic equipment. As an actuator, air springs provide either linear or angular motion. These air springs offer a favorable stroke-to-compressed height ratio when compared to air cylinders, and can accept a wider variety of actuation media, such as air, water, nitrogen or anti-freeze. Air springs can simultaneously isolate harmful vibrations while regulating load height, as well as allow constant vibration isolation under varying loads. These springs are constructed of fabric-reinforced Wingprene or natural rubber, with corrosion-protected end retainers. Complete installation and operating instructions are enclosed with each air spring. Do not use air springs where load torsion may occur. Springs do not have internal bumpers—do not exceed rated maximum load range. Listed stroke distances are measured from the compressed height of the spring to the overall height at maximum inflation
1.75 3.40 Dia.
3/8-16
UNC Blind Tap x 16mm DP 2 Places
1/4"
Maximum Height
Air Fitting Port Maximum Diameter at 100 PSI
Compressed Height
Compressed height of 1.8". Bottom retainer is the same as upper retainer illustrated minus the 1⁄4" air fitting port. Force Lbs. at a Stroke of: Item No.
Max. Stroke
AS-100 AS-101
2.0 3.0
1"
2"
1,250 550 1,500 1,200
Max. Stroke
550 500
Isolator Load Range
Design Height Range (In.)
1,100 - 1,370 2.5 - 3 975 - 1,560 2.5 - 4
Max. Dia. @ 100 psi
5.7 6.0
Max. Pack Height Qty.
3.8 4.8
1 1
Note: Isolator Load Range is based on 100 psi. To obtain a lower limit (i.e. minimum load at 20 psi) divide the smaller value by 5.
915
SHOCK ABSORBERS & ACCESSORIES Adjustable Shock Absorbers
A
EE Wrench Flats
F M
B
.50 H
E Dia.
D J Dia.
T
Item No.
Inch ACE-0035 ACE-0150 ACE-0225 ACE-0600 ACE-0900 Metric ACE-0035M ACE-0150M ACE-0225M ACE-0600M
Ace
Stroke
A
B
D
E
F
H
J
M
MA35 MA150B MA225 MA600 MA900
.40 .50 .75 1.00 1.58
3.31 3.59 4.67 5.62 7.44
.71 .87 1.18 1.43 2.01
.13 .19 .19 .25 .25
.42 .46 .66 .88 .88
2.41 2.44 2.94 3.54 4.78
.30 .47 .66 .90 .90
.32 .43 .43 .43 .43
.18 .28 .55 .65 .65
MA35M MA150M MA225M MA600M
10.1 12.7 19.1 25.4
84.1 93.2 118.6 142.7
18.3 24.1 30.0 36.3
3.3 4.8 4.8 6.3
10.6 11.6 16.8 22.4
61.2 62.0 74.7 90.0
7.6 11.9 16.8 22.9
8.0 11.0 11.0 11.0
4.6 7.1 14.0 16.5
T 1
⁄2-20 ⁄ -18 ⁄ -16 1-12 1-12
9
16 3 4
EE
Effective Weight Lbs.
Energy/ Cycle In. Lbs.
Energy/Hr. In. Lbs./ Hr.
Pack Qty.
— .49 ⁄16 7 ⁄8 7 ⁄8
13 - 125 2 - 240 5 - 500 20 - 3,000 30 - 4,500
35 200 300 600 900
53,000 300,000 400,000 600,000 800,000
1 1 1 1 1
— 12.7 18.0 23.0
13 - 125 2 - 240 5 - 500 20 - 3,000
35 200 300 600
53,000 300,000 400,000 600,000
1 1 1 1
11
M12 x 1 M14 x 1.5 M20 x 1.5 M25 x 1.5
Soft Contact/Self-Compensating
EE Wrench Flats
.50
M
A F Stroke
B H
E Dia.
D
T
J
Soft contact is suggested when a low initial reaction force is required at impact. Self-compensating is utilized to obtain maximum energy absorption capacity. Both are recommended when a range of loads and impact velocities are encountered in the same application. Temperature range 32 to 150 degree Fahrenheit. Oil type ACE #5. Effective Weight Lbs. Item No.
Ace
Inch ACE-1901 SC-190-1 ACE-1902 SC-190-2 ACE-1903 SC-190-3 ACE-1904 SC-190-4 ACE-3001 SC-300-1 ACE-3002 SC-300-2 ACE-3003 SC-300-3 ACE-3004 SC-300-4 ACE-3005 SC-300-5 ACE-3006 SC-300-6 ACE-3007 SC-300-7 ACE-3008 SC-300-8 ACE-3009 SC-300-9 ACE-6501 SC-650-1 ACE-6502 SC-650-2 ACE-6503 SC-650-3 ACE-6504 SC-650-4 ACE-6505 SC-650-5 ACE-6506 SC-650-6 ACE-6507 SC-650-7 ACE-6508 SC-650-8 ACE-6509 SC-650-9 ACE-9251 SC-925-1 ACE-9252 SC-925HD-2 ACE-9253 SC-925HD-3 ACE-9254 SC-925HD-4 Inch (Metric Thread) ACE-1905 SC-190M-5 ACE-1906 SC-190M-6 ACE-1907 SC-190M-7
916
Stroke
A
B
D
E
F
H
J
M
.63 .63 .63 .63 .75 .75 .75 .75 .59 .59 .59 .59 .59 1.00 1.00 1.00 1.00 1.91 1.91 1.91 1.91 1.91 1.58 1.58 1.58 1.58
4.50 4.50 4.50 4.50 4.62 4.62 4.62 4.62 4.15 4.15 4.15 4.15 4.15 5.62 5.62 5.62 5.62 5.51 5.51 5.51 5.51 5.51 7.44 7.44 7.44 7.44
1.06 1.06 1.06 1.06 1.18 1.18 1.18 1.18 1.02 1.02 1.02 1.02 1.02 1.43 1.43 1.43 1.43 1.33 1.33 1.33 1.33 1.33 2.01 2.01 2.01 2.01
.16 .16 .16 .16 .19 .19 .19 .19 .25 .25 .25 .25 .25 .25 .25 .25 .25 .38 .38 .38 .38 .38 .25 .25 .25 .25
.46 .46 .46 .46 .66 .66 .66 .66 .66 .66 .66 .66 .66 .87 .87 .87 .87 .87 .87 .87 .87 .87 .87 .87 .87 .87
3.00 3.00 3.00 3.00 3.09 3.09 3.09 3.09 2.78 2.78 2.78 2.78 2.78 3.83 3.83 3.83 3.83 3.80 3.80 3.80 3.80 3.80 5.10 5.10 5.10 5.10
.47 .47 .47 .47 .66 .66 .66 .66 .66 .66 .66 .66 .66 .90 .90 .90 .90 .90 .90 .90 .90 .90 .90 .90 .90 .90
.43 .43 .43 .43 .43 .43 .43 .43 .43 .43 .43 .43 .43 .43 .43 .43 .43 .43 .43 .43 .43 .43 .43 .43 .43 .43
.28 .28 .28 .28 .28 .28 .28 .28 .28 .28 .28 .28 .28 .28 .28 .28 .28 .28 .28 .28 .28 .28 .28 .28 .28 .28
.47 .47 .47
3.70 3.70 3.70
1.67 1.67 1.67
.19 .19 .19
.46 .46 .46
2.83 2.83 2.83
— — —
— — —
.20 .20 .20
T 9
EE 1
⁄16-18 ⁄16-18 ⁄16-18 9 ⁄16-18 3 ⁄4-16 3 ⁄4-16 3 ⁄4-16 3 ⁄4-16 3 ⁄4-16 3 ⁄4-16 3 ⁄4-16 3 ⁄4-16 3 ⁄4-16 1-12 1-12 1-12 1-12 1-12 1-12 1-12 1-12 1-12 1-12 1-12 1-12 1-12
⁄2 ⁄2 ⁄2 1 ⁄2 11 ⁄16 11 ⁄16 11 ⁄16 11 ⁄16 11 ⁄16 11 ⁄16 11 ⁄16 11 ⁄16 11 ⁄16 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8 7 ⁄8
M14 x 1.5 M14 x 1.5 M14 x 1.5
.39 .39 .39
9 9
1 1
Soft Contact
SelfCompensating
5 - 13 3 - 15 12 - 36 8 - 40 30 - 90 20 - 100 75 - 200 50 - 225 5 - 15 3 - 18 15 - 50 10 - 60 50 - 150 30 - 180 150 - 400 70 - 450 38 - 90 25 - 100 115 - 270 75 - 300 300 - 360 200 - 400 450 - 1,350 300 - 1,500 1,050 - 3,900 700 - 4,300 24 - 80 17 - 100 75 - 250 50 - 300 240 - 800 150 - 900 800 - 2,400 450 - 2,600 75 - 225 50 - 250 300 - 720 200 - 800 1,050 - 2,150 700 - 2,400 2,500 - 5,200 1,700 - 5,800 6,000 - 12,500 4,000 - 14,000 50 - 160 30 - 200 130 - 460 90 - 600 400 - 1,350 250 - 1,600 1,200 - 4,300 750 - 4,600 — — —
4.4 - 35.2 29 - 309 300 - 3,400
Energy/ Energy/Hr. Cycle In. Lbs./ Pack In. Lbs. Hr. Qty.
225 225 225 225 300 300 300 300 650 650 650 650 in 650 in 650 650 650 650 1,860 1,860 1,860 1,860 1,860 975 975 975 975
300,000 300,000 300,000 300,000 400,000 400,000 400,000 400,000 400,000 400,000 400,000 400,000 400,000 600,000 600,000 600,000 600,000 600,000 600,000 600,000 600,000 600,000 800,000 800,000 800,000 800,000
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
274 274 274
443,000 443,000 443,000
1 1 1
SHOCK ABSORBERS & ACCESSORIES Determine load weight, impact velocity (in./sec.), propelling force (if any), cycles per hour, and stroke (in.) required. Calculate total energy (in.-lbs.) and total energy per hour (In.-lbs./hr.) to select proper shock. Small Adjustable Hydraulic Series E
G
H
F A
ED-1, ED-2R
E
G
D
C
H
F
ED-3, ED-4
D
C A
Use with pallet stops, air cylinders, rolling doors, and other various manufacturing applications. Standard corrosion resistant nickel plating. Adjustments are made by turning the 180 degree adjustment knob. Adjustments are locked with a setscrew. One hex jam nut supplied with each shock. Additional mounting accessories are available below. Item No.
Bore Size In.
Stroke inches
Max. In.-Lbs. Per Cycle
ED-1 ED-2R ED-3 ED-4
.28 .50 .63 .63
.5 1.0 1.0 2.0
250 650 1700 3400
Nominal Coil Spring Force Max. Max. Max. Extension Compression Propelling In.-Lbs. Shock Lbs. Lbs. Force Lbs. Per Hour Force Lbs.
284,000 622,000 808,000 986,000
775 1,000 2,500 2,500
1.25 3.00 9.00 5.00
2.75 6.00 13.00 13.00
Hex Jam Nuts for Self-Compensating Hydraulic Series
150 300 500 500
A
UNF C
D
E
F
G
H
Pack Qty.
4.35 5.62 6.12 8.74
3 ⁄4-16 1-12 13⁄8-12 13⁄8-12
.190 .250 .375 .375
.50 .62 1.13 1.13
3.31 4.09 3.81 5.43
.63 .88 1.10 1.10
.67 .56 .55 .55
1 1 1 1
Stop Collars
A B
B C
Hex Jam Nut
Item No.
A
B
C
Shock Absorber
Pack Qty.
ED-100 ED-200 ED-700 ED-800 ED-900
1.08 1.30 .58 .72 1.01
.94 1.13 .50 .63 .88
.18 .18 .09 .12 .31
ED-1 ED-2R ED-7 ED-8 ED-9
1 1 1 1 1
A
Item No.
A
B
Shock Absorber
Pack Qty.
ED-101 ED-202 ED-303
1.50 1.75 2.50
1.00 1.50 1.69
ED-10 ED-11 ED-3, ED-4
1 1 1
Low Profile Adjustable Hydraulic Series
Larger capacity for use in automotive robotics, glass forming equipment, foundry conveyor lines, manufacturing rail carts, and numerous other applications. Recessed 360 degree adjustment setting knob on side of shock absorber for ease of mounting. Mounting accessories available below. Nominal Coil Spring Force
Item No.
Bore Size In.
Stroke inches
Max. In.-Lbs. Per Cycle
Max. In.-Lbs. Per Hour
Max. Shock Force Lbs.
Extension Lbs.
Compression Lbs.
Max. Propelling Force Lbs.
A
B
C
Pack Qty.
ED-5 ED-6
.75 .75
1 2
2300 4600
1,120,000 1,475,000
3,000 3,000
11.00 7.00
15 15
650 650
5.69 7.69
3.63 4.63
.42 .50
1 1
Lock Ring
Stop Collar
Square Flange
.34
.38
2.25 1.63
Lock Slot
2.0 1.94 2.22 1.94
For use with shock absorbers shown above.
For use with shock absorbers shown above.
.50
For use with shock absorbers shown above. Use 5⁄16" bolt.
Item No.
Shock Absorber
Pack Qty.
Item No.
Pack Qty.
Item No.
Shock Absorber
Pack Qty.
ED-500
ED-5, ED-6
1
ED-505
1
ED-600
ED-5, ED-6
1
917
SHOCK ABSORBERS These shock absorbers are fully threaded for ease of installation. Outer body made of steel with black oxide finish. Piston rod is made of high tensile steel, hardened and chrome plated. Rod end button is made of hardened steel with black oxide finish. Return spring is zinc plated. For maximum heat dissipation, do not paint shock absorber. Operating temperature is 10 degrees to 158 degrees Fahrenheit. Oil type is ATF. Lock nut included with each shock absorber.
K D
T
I
G H
Stroke B
A
J
Self-Compensating Used to obtain maximum energy absorption capacity. Impact velocity range is 0.5 to 16.5 ft./sec. Adjustable Adjustable from either front or rear. Impact velocity range is 0.5 to 16.5 ft./sec. Low Velocity Adjustable Adjustable from either front or rear. Impact velocity range is 0.6 to 1.5 ft./sec. Item No.
Ace
Stroke
Self-Compensating / Soft Contact ACE-3325-1 MC3325-1 .91 ACE-3325-2 MC-3325-2 .91 ACE-3325-3 MC3325-3 .91 ACE-3325-4 MC3325-4 .91 ACE-3350-1 MC3350-1 1.91 ACE-3350-2 MC3350-2 1.91 ACE-3350-3 MC3350-3 1.91 ACE-3350-4 MC3350-4 1.91 ACE-4525-1 MC-4525-1 .91 ACE-4525-2 MC4525-2 .91 ACE-4525-4 MC4525-4 .91 ACE-4550-1 MC4550-1 1.91 ACE-4550-2 MC4550-2 1.91 ACE-4575-2 MC4575-2 2.91 ACE-4575-3 MC-4575-3 2.91 ACE-4525-3 MC4525-3 .91 ACE-6450-2 MC6450-2 1.91 Adjustable ACE-105 MA3325 .91 ACE-106 MA3625 .91 ACE-107 MA4525 .91 ACE-108 MA4550 1.91 ACE-109 MA3350 1.91 ACE-110 MA3650 1.91 ACE-111 MA4575 2.91 ACE-112 MA6450 1.91 ACE-113 MA64100 3.91 Low Velocity Adjustable ACE-115 ML3325 .91 ACE-116 ML3625 .91 ACE-118 ML3650 1.91 ACE-119 ML4525 .91 ACE-120 ML4550 1.91 ACE-121 ML6425 .91
J
K
T
Effective Weight Lbs.
Energy/ Cycle In. Lbs.
Energy/Hr. In. Lbs./Hr.
Pack Qty.
⁄8 ⁄8 ⁄8 1 ⁄8 1 ⁄8 1 ⁄8 1 ⁄8 1 ⁄8 1 ⁄8 1 ⁄8 1 ⁄8 1 ⁄8 1 ⁄8 1 ⁄8 1 ⁄8 1 ⁄8 1 ⁄4
.75 .75 .75 .75 .75 .75 .75 .75 .87 .87 .87 .87 .87 .87 .87 .87 1.06
1.15 1.15 1.15 1.15 1.15 1.15 1.15 1.15 1.65 1.65 1.65 1.65 1.65 1.65 1.65 1.65 2.37
11⁄4-12 11⁄4-12 11⁄4-12 11⁄4-12 11⁄4-12 11⁄4-12 11⁄4-12 11⁄4-12 13⁄4-12 13⁄4-12 13⁄4-12 13⁄4-12 13⁄4-12 13⁄4-12 13⁄4-12 13⁄4-12 21⁄2-12
20 - 80 68 - 272 230 - 920 780 - 3,120 40 - 160 136 - 544 460 - 1,840 1,560 - 6,240 50 - 200 170 - 680 1,950 - 7,800 100 - 400 340 - 1,360 510 - 2,040 1,730 - 6,920 575 - 2,300 1,020 - 4,080
1,350 1,350 1,350 1,350 2,700 2,700 2,700 2,700 3,000 3,000 3,000 6,000 6,000 9,000 9,000 3,000 15,000
670,000 670,000 670,000 670,000 760,000 760,000 760,000 760,000 950,000 950,000 950,000 1,000,000 1,000,000 1,300,000 1,300,000 950,000 1,300,000
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1.00 1.00 1.38 1.38 1.00 1.00 1.38 1.90 1.90
1
⁄8 ⁄8 ⁄8 1 ⁄8 1 ⁄8 1 ⁄8 1 ⁄8 1 ⁄4 1 ⁄4
.75 .75 .87 .87 .75 .75 .87 1.06 1.06
1.15 1.15 1.65 1.65 1.15 1.15 1.65 2.37 2.37
11⁄4-12 13⁄8-12 13⁄4-12 13⁄4-12 11⁄4-12 13⁄8-12 13⁄4-12 21⁄2-12 21⁄2-12
20 - 3,800 20 - 3,800 95 - 22,000 150 - 32,000 28 - 5,400 28 - 5,400 155 - 33,000 600 - 115,000 600 - 115,000
1,500 1,500 3,450 6,900 3,000 3,000 10,350 36,000 36,000
670,000 670,000 950,000 1,000,000 760,000 760,000 1,300,000 1,700,000 1,700,000
1 1 1 1 1 1 1 1 1
1.00 1.00 1.00 1.38 1.38 1.90
1
.75 .75 .75 .87 .87 1.06
1.15 1.15 1.15 1.65 1.65 2.37
11⁄4-12 13⁄8-12 13⁄8-12 13⁄4-12 13⁄4-12 21⁄2-12
— — — — — —
1,500 1,500 3,000 3,450 6,900 9,000
670,000 670,000 760,000 950,000 1,000,000 1,100,000
1 1 1 1 1 1
A
B
D
G
H
I
5.44 5.44 5.44 5.44 7.44 7.44 7.44 7.44 5.69 5.69 5.69 7.69 7.69 9.69 9.69 5.69 8.85
2.19 2.19 2.19 2.19 3.19 3.19 3.19 3.19 1.97 1.97 1.97 2.97 2.97 3.97 3.97 1.97 3.35
.375 .375 .375 .375 .375 .375 .375 .375 .500 .500 .500 .500 .500 .500 .500 .500 .750
.99 .99 .99 .99 .99 .99 .99 .99 1.36 1.36 1.36 1.36 1.36 1.36 1.36 1.36 1.86
1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.38 1.38 1.38 1.38 1.38 1.38 1.38 1.38 1.90
1
5.44 5.44 5.69 7.69 7.44 7.44 9.69 8.85 12.85
2.19 2.19 1.97 2.97 3.19 3.19 3.97 3.35 5.35
.375 .375 .500 .500 .375 .375 .500 .750 .750
.99 .99 1.36 1.36 .99 .99 1.36 1.86 1.86
5.44 5.44 7.44 5.69 7.69 6.85
2.19 2.19 3.19 1.97 2.97 2.35
.375 .375 .375 .500 .500 .750
.99 .99 .99 1.36 1.36 1.86
1 1
1 1
⁄8 ⁄8 ⁄8 1 ⁄8 1 ⁄8 1 ⁄4 1 1
Adjustable Miniature Shock Absorber
A1 A F
EE
B
L G
H
Item No.
Ace
ACE-AS381 AS3/8X1
918
D
K
T
Stroke
A
A1
B
D
F
H
K
L
Q
T
EE
Effective Weight Lbs.
Energy/ Cycle
1
4.75
5
1.38
0.31
3.37
0.75
0.87
0.93
0.5
1-12
0.88
10 - 1,250
600
Energy/Hr. Pack In. Lbs./Hr. Qty.
600,000
1
SHOCK ABSORBERS & ACCESSORIES Flanged Stop Collars
D E C B
H
F G
Item No.
Ace
ACE-45 ACE-46
250-0642 250-0072
Thread Size
C
D
F
G
H
Used With
Pack Qty.
1.50 2.25
2.50 3.25
.88 .88
.25 .25
.282 .282
ACE-3325-1 thru 3350-4, 115 ACE-4525-1 thru 4575-3, 119, 120
1 1
B
11⁄4-12 1.63 13⁄4-12 1.50
Mounting Blocks
F
F
B D
F
C
G
C E
F
A
D B
F
ACE-1 ACE-2 ACE-3 ACE-4
250-0306 250-0308 250-0318 250-0401
ACE-5 250-0402 ACE-6 ACE-7 ACE-8 ACE-9 ACE-10
250-0016 250-0023 250-0028 250-0633 250-0024
G
D B
G F
ACE-1, 2 Ace
E
E C
C
A
A
Item No.
A
G
ACE-3, 4, 5
D B
ACE-7, 8
ACE-6, 9, 10 Pack Qty.
A
B
C
D
E
F
G
Used With
⁄8-32 ⁄2-20 ⁄16-18 3 ⁄4-16
1.50 1.50 1.81 2.00
1.00 1.00 1.37 1.50
1.00 1.00 1.38 1.50
— — 1.00 1.12
#8-32 Soc. Hd. Screw #8-32 Soc. Hd. Screw #10-32 Soc. Hd. Screw #10-32 Soc. Hd. Screw
.56 .56 .62 .62
1-12
2.00
1.50
1.50
1.12
#10-32 Soc. Hd. Screw
.62
11⁄4-12 13⁄4-12 21⁄2-12 13⁄8-12 13⁄4-12
2.00 2.25 3.50 2.00 3.00
1.50 2.25 3.50 1.75 2.25
1.62 1.62 2.75 1.62 2.38
1.12 1.62 2.75 1.12 1.62
.219 .340 .410 .219 .340
.38 .50 .62 .38 .50
ACE-1024, 1025, 1026 ACE-0035, 1075 ACE-1150, 1151, 1152, 1901,1902, 1903, 1904 ACE-0225, 2225, 1225, 1226, 1227, 3001, 3002, 3003, 3004 ACE-1600, 1601, 1602, 0600, 0900, 2600, 2900, 6501, 6502, 6503, 6504, 9251, 9252, 9253, 9254 ACE-3325-1 thru 3350-4, 105, 107, 115 ACE-4525-1 thru 4575-3, 109, 110, 111, 119, 120 ACE-6450-2, 112, 113, 121 ACE-106, 108, 116, 118 ACE-4525-1 thru 4575-3, 107, 108, 111, 115
3 1 9
Stop Collars
1 1 1 1 1 1 1 1 1 1
Lock Nuts A
D
A B
ACE-21-25 ACE-28-29 Item No. Item No.
Ace
A
B
C
Pack Qty.
Used With
ACE-11 250-0406 3⁄8-32 .81 .56 ACE-12 250-0407 1⁄2-20 .81 .62 ACE-13 250-0271 9⁄16-18 .75 .69
ACE-1024, 1025, 1026 ACE-0035, 1075 ACE-1150, 1151, 1152, 1901, 1902, 1903, 1904 ACE-0225, 2225, 1225, 1226, 1227, 3001, 3002, ACE-14 250-0403 3⁄4-16 1.25 1.00 3003, 3004 ACE-1600, 1601, 1602, 0600, 0900, 2600, 2900, ACE-15 250-0275 1-12 1.75 1.25 6501, 6502, 6503, 6504, 9251, 9252, 9253, 9254
Ace
A
B
D
B
D Pack Qty.
Used With
ACE-21 250-0404 3⁄8-32 .50 .09 ACE-1024, 1025, 1026 ACE-22 250-0405 1⁄2-20 .62 .13 ACE-0035, 1075 ACE-23 250-0231 9⁄16-18 .88 .31 ACE-1150, 1151, 1152, 1901, 1902, 1903, 1904 ACE-0225, 2225, 1225, 1226, 1227, 3001, 3002, ACE-24 250-0399 3⁄4-16 1.00 .25 3003, 3004 ACE-1600, 1601, 1602, 0600, 0900, 2600, 2900, ACE-25 250-0400 1-12 1.25 .25 6501, 6502, 6503, 6504, 9251, 9252, 9253, 9254 ACE-28 250-0631 13⁄8-12 — .25 ACE-116, 118 ACE-29 250-0042 21⁄2-12 — .37 ACE-121
1 1 1 1 1
1 1 1 1 1 1 1
Hydraulic Speed/Feed Controllers
B 1.25
.38
1.19
1.19
.50
C
E .31
1.03
.50 A
D
.56
Tension Item No.
Ace
Stroke
A
B
C
D
ACE-3200 ACE-3400* ACE-3600*
DVC-2 DVC-4 DVC-6
2.00 4.00 6.00
.25 .25 .25
9.81 13.81 17.81
.25 .25 .25
.25 .25 .25
Compression
E
Maximum Propelling Force Lbs.
Minimum Force to Operate Through Full Stroke Lbs.
Maximum Propelling Force Lbs.
Minimum Force to Operate Through Full Stroke Lbs.
Pack Qty.
2.93 4.93 6.93
450 450 450
9.5 — —
450 375 300
9.5 — —
1 1 1
*External mechanical stops required
919
SHOCK ABSORBERS Self-Compensating
EE Wrench Flats
M
.05
A F
B Stroke
E Dia. D Dia.
T
ACE-1150 - 1602, 1010, 1011, 1005M - 1601M
A Stroke M
B .32
F
E
H T
ACE-1024 - 1075
D Dia.
Small size allows for high energy absorption in confined spaces. The self-compensating design accommodates a variety of load conditions. Threaded outer bodies. Temperature range 32-150 degree Fahrenheit. Not compatible with petroleum based fluids. Silicone type oil. Item No.
Inch ACE-1024* ACE-1025* ACE-1026* ACE-1075* ACE-1150 ACE-1151 ACE-1152 ACE-1225 ACE-1226 ACE-1227 ACE-1600 ACE-1601 ACE-1602 Metric ACE-1005M ACE-1009M1 ACE-1009M2 ACE-1010 ACE-1011 ACE-1025M ACE-1026M ACE-1027M ACE-1030M1 ACE-1030M2 ACE-1030M3 ACE-1075M** ACE-1150M ACE-1150ME ACE-1151M ACE-1152M ACE-1225M ACE-1227M ACE-1600M ACE-1601M
T
Effective Weight Lbs.
Energy/ Cycle In. Lbs.
Energy/Hr. In. Lbs./Hr.
Pack Qty.
— — — — .525 .525 .525 .632 .632 .632 .838 .838 .838
⁄8-32 ⁄8-32 ⁄8-32 1 ⁄2-20 9 ⁄16-18 9 ⁄16-18 9 ⁄16-18 3 ⁄4-16 3 ⁄4-16 3 ⁄4-16 1-12 1-12 1-12
1.5 - 5.0 4 - 12 10 - 30 6 - 80 2 - 22 20 - 200 150 - 450 5 - 55 50 - 500 400 - 2,000 20 - 300 250 - 2,500 880 - 5,000
20 20 20 75 175 175 175 360 360 360 1200 1200 1200
200,000 200,000 200,000 250,000 300,000 300,000 300,000 400,000 400,000 400,000 600,000 600,000 600,000
1 1 1 1 1 1 1 1 1 1 1 1 1
— — — — — — — — — — — — 6.4 6.4 6.4 6.4 8.0 8.0 9.6 9.6
M5 x 0.5 M6 x 0.5 M6 x 0.5 M8 x 0.75 M8 x 0.75 M10 x 1 M10 x 1 M10 x 1 M8 x 1 M8 x 1 M8 x 1 M12 x 1 M14 x 1.5 M14 x 1.5 M14 x 1.5 M14 x 1.5 M20 x 1.5 M20 x 1.5 M25 x 1.5 M25 x 1.5
.22 - 2.0 1.35 - 7.0 1.75 - 9.0 .75 - 6.0 1.5 - 11 1.5 - 5.0 4 - 12 10 - 30 1.0 - 4.3 3.97 - 11.9 11.02 - 33.0 6 - 80 2 - 22 2 - 22 20 - 200 150 - 450 5 - 55 400 - 2,000 20 - 300 250 - 2,500
6 9 9 11 11 20 20 20 31 31 31 75 175 175 175 175 360 360 1,200 1,200
18,000 18,000 18,000 35,000 35,000 200,000 200,000 200,000 50,000 50,000 50,000 250,000 300,000 300,000 300,000 300,000 400,000 400,000 600,000 600,000
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Ace
Stroke
A
B
D
E
F
H
M
EE
MC25L MC25 MC25H MC75-3 MC150 MC150H MC150H2 MC225 MC-225H MC225H2 MC600 MC600H MC600H2
.26 .26 .26 .40 .50 .50 .50 .50 .50 .50 1.00 1.00 1.00
2.27 2.27 2.27 2.76 3.41 3.41 3.41 3.81 3.81 3.81 5.58 5.58 5.58
.57 .57 .57 .72 .69 .69 .69 .69 .69 .69 1.24 1.24 1.24
.13 .13 .13 .13 .19 .19 .19 .25 .25 .25 .31 .31 .31
.33 .33 .33 .41 .46 .46 .46 .66 .66 .66 .89 .89 .89
1.30 1.30 1.30 1.74 2.44 2.44 2.44 2.84 2.84 2.84 4.06 4.06 4.06
.30 .30 .30 .30 — — — — — — — — —
.20 .20 .20 .218 .28 .28 .28 .28 .28 .28 .28 .28 .28
MC5M1-B MC9M1 MC9M2 MC10EL MC-10EH MC25M MC25MH MC25MH-NB MC30M1 MC30M2 MC30M3 MC75M3-880 MC150M MC150ME MC150MH MC150MH2 MC225M MC225MH2 MC600M MC600MLH
4.1 5.0 5.0 5.0 5.0 6.6 6.6 6.6 8.1 8.1 8.1 10.2 12.7 12.7 12.7 12.7 12.7 12.7 25.4 25.4
34.0 36.0 36.0 38.6 38.6 57.7 57.7 57.3 54.0 54.0 54.0 67.7 86.6 86.6 86.6 86.6 96.8 96.8 141.8 141.8
8.2 10.0 10.0 10.0 10.0 14.5 14.5 14.5 13.2 13.2 13.2 — 17.4 17.4 17.4 17.4 17.6 17.6 30.9 30.9
1.5 2.0 2.0 2.0 2.0 3.3 3.3 3.3 2.5 2.5 2.5 3.3 4.8 4.8 4.8 4.8 6.3 6.3 7.9 7.9
4.1 5.0 5.0 6.4 6.4 8.4 8.4 8.4 6.5 6.5 6.5 10.4 11.6 11.6 11.6 11.6 16.7 16.7 22.7 22.7
21.1 21.1 21.1 21.1 21.1 33.0 33.0 33.0 34.3 34.3 34.3 44.2 62.0 62.0 62.0 62.0 72.1 72.1 103.1 103.1
3.3 4.7 4.7 — — 7.6 7.6 7.6 6.5 6.5 6.5 — 11.9 11.9 11.9 11.9 16.7 16.7 23.0 23.0
2.5 2.5 2.5 4.8 4.8 5.0 5.0 5.0 4.1 4.1 4.1 4.6 7.1 7.1 7.1 7.1 7.1 7.1 7.1 7.1
.375
.563
3 3 3
*Includes button **880-No button, standard rod
Adjustable Double Acting Hydraulic Series
.251
1.06
1.25
.50 .251
.25
F L L+Stroke
Used in food processing, refrigeration cases, material handling, air cylinders and various other manufacturing applications. Determine required stroke (in.) control direction desired (compression, tension or both) and maximum propelling force in the desired direction to select appropriate shock absorber. Dampening force adjustments are made by rotating adjustment knob 180 degrees. Bore size is .625". Adjustable Compression Adjustable Compression and Tension Item No.
Item No.
Stroke Max. Inches
In.-Lbs. Per Cycle
Max. In.-Lbs. Per Hour
— ED-13* ED-14 ED-150* —
ED-120 ED-130 ED-140 ED-15 ED-16
2 4 6 8 10
1800 3300 4500 5200 6250
650,000 850,000 1,050,000 1,250,000 1,450,000
*Free flow in tension mode, adjustable in compression mode
920
Max. Propelling Max. Propelling Force Force Compression Extension Lbs. Lbs.
450 450 450 450 450
450 375 300 200 125
F
L
Pack Qty.
6.87 8.87 10.87 12.87 14.87
7.81 9.81 11.81 13.81 15.8
1 1 1 1 1
SHOCK ABSORBERS & ACCESSORIES Self-Compensating Hydraulic Series
B E
G D F
C A
Item No.
Bore Size In.
Stroke inches
ED-7A* ED-7B* ED-7C* ED-8A ED-8B ED-9A ED-9B ED-10A ED-10B ED-11A ED-11B
.18 .18 .18 .28 .28 .28 .28 .44 .44 .50 .50
.25 .25 .25 .62 .62 .62 .62 .87 .87 1 1
Max. In.-Lbs. Max. Per In.-Lbs. Cycle Per Hour
25 25 25 235 235 235 235 485 485 800 800
Max. Shock Force Lbs.
50,000 50,000 50,000 300,000 300,000 300,000 300,000 475,000 475,000 622,000 622,000
Nominal Coil Spring Force Extension Lbs
200 200 200 625 625 625 625 850 850 1,250 1,250
Impact Compression Velocity Lbs. In./Sec.
0.60 0.60 0.60 1.00 1.00 1.00 1.00 2.00 2.00 3.00 3.00lbs
1.25 1.25 1.25 2.50 2.50 2.50 2.50 6.80 6.80 6.00 6.00
60-125 25-110 10-60 20-145 10-70 20-145 10-70 20-145 5-50 10-145 10-35
Used with medical equipment, packaging machinery, air cylinders, turnstiles, and various other manufacturing applications. Standard corrosion resistant nickel plating. One hex jam nut included. Additional mounting accessories are available below. All have hydraulic stop at full stroke, therefore it is important to position the shock absorber such that full stroke is used to prevent undesirable bottoming against the positive stop. Max. Total Propelling Energy Force In./Lbs. Lbs.
5-25 5-25 5-25 10-190 10-160 10-190 10-160 25-400 25-350 20-140 5-40
45 45 45 200 200 200 200 360 360 500 500
A
B
2.25 2.25 2.25 4.22 4.22 4.22 4.22 5.13 5.13 5.57 5.57
.38 .38 .38 .47 .47 .47 .47 .47 .47 .47 .47
UNF C 3
⁄8-32 ⁄8-32 ⁄8-32 1 ⁄2-20 1 ⁄2-20 9 ⁄16-18 9 ⁄16-18 3 ⁄4-16 3 ⁄4-16 1-12 1-12 3 3
D
E
F
G
Pack Qty.
.10 .10 .10 .16 .16 .16 .16 .19 .19 .25 .25
.27 .27 .27 .44 .44 .44 .44 .50 .50 .62 .62
1.61 1.61 1.61 3.20 3.20 3.20 3.20 3.76 3.76 4.04 4.04
.26 .26 .26 .43 .43 .43 .43 .64 .64 .89 .89
1 1 1 1 1 1 1 1 1 1 1
*Not nickel plated
Hex Jam Nuts for Self-Compensating Hydraulic Series
Stop Collars for Self-Compensating Hydraulic Series
B
A B
Hex Jam Nut
A
C
Item No.
A
B
C
Shock Absorber
Pack Qty.
ED-100 ED-200 ED-700 ED-800 ED-900
1.08 1.30 .58 .72 1.01
.94 1.13 .50 .63 .88
.18 .18 .09 .12 .31
ED-1 ED-2R ED-7 ED-8 ED-9
1 1 1 1 1
Item No.
A
B
Shock Absorber
Pack Qty.
ED-707* ED-808 ED-909 ED-101 ED-202
.75 1.00 1.00 1.50 1.75
.58 .75 .69 1.00 1.50
ED-7 ED-8 ED-9 ED-10 ED-11
1 1 1 1 1
*Hex shape .50 across flats
Rotary Dampers For smooth mechanical motions. Used in VCR loading mechanisms, glovebox doors, window shades, copy machine lids or anywhere controlled rotary motion is needed. Two way damping controls the movement in both directions. Maximum cycle rate is 10 cycles per minute. Nominal torque ratings are measured at 20 RPM and 73 degrees Fahrenheit. Torque is affected by temperature. Calculate nominal torque using the formula shown.
T=(L/2) x (W) x (cos Ø) Where: T=Nominal Torque L=Length from pivot to the end of the lid Ø=The angle between the panel and horizontal W=The free weight of the lid
L
W
.126
.157
.157
.197
ACE-RD301
.315 .138
.165
.591 .409 .177
.984 .581
.551
.827 1.083
1.417 .472 1.850
.197 .236
1.417 1.850
.748
.335
ACE-RD302
ACE-RD203
ACE-RD501
1.575 1.969
.059
.205
1.575 .236 .197 .394
.079
ACE-RD502
.197 .276
Nominal torque in oz. 4.17 Standard spur gear option Gear has 11 involute (full) teeth Module .031 Pitch circle diameter .346
1.654 1.102
Nominal torque in oz. 6.94 Gear has 12 involute (full) teeth Module .039 Pitch circle diameter .472
Nominal torque in lbs. 17.36 No gear option
Item No.
Ace
Gear
Pack Qty.
Item No.
Ace
Gear
Pack Qty.
Item No.
Ace
Gear
Pack Qty.
ACE-RD301 ACE-RD302
RT-C2-301 RT-C2-301-G1
w/o Gear w/ Gear
1 1
ACE-RD501 ACE-RD502
RT-D2-501 RT-D2-501-G1
w/o Gear w/ Gear
1 1
ACE-RD203
RT-F2-203
w/o Gear
1
921