#7079-EN

Page 1

Build wind-powered generators to energize your electric vehicles # 7079GREEN ENERGY 124 PIECES 8+ AGES 8 MODELS ELECTRIC GENERATOR
1 TABLE OF CONTENTS Table of Contents ............................................................................................................................................. 1 Safety Information 2 Kit Contents ....................................................................................................................................................... 3 Check It Out 4~9 Tips and Tricks........................................................................................................................................... 10~11 Indoor Experiments ....................................................................................................................................... 12 Setting up the Windmills 13 Let’s Do Some Experiments! ......................................................................................................................... 14 Storing the Generated Electricity 15 Advanced Reference ............................................................................................................................... 16~18 Testing Results 19~20 ASSEMBLY INSTRUCTIONS START ON PAGE 21 MODEL 1 Windmill with Long-Blade ................................................................................................. 21 MODEL 2 Windmill with Short-Blade ................................................................................................ 25 MODEL 3 Glider ................................................................................................................................... 27 MODEL 4 Sail Car .................................................................................................................................. 29 MODEL 5 Tricycle ................................................................................................................................. 31 MODEL 6 Jet Car ................................................................................................................................... 33 MODEL 7 Tractor .................................................................................................................................. 35 MODEL 8 Race Car ................................................................................................................................ 37 Improper use of the battery may create a risk of electrical leakage, this may cause damage to the surrounding environment of the battery, the possibility of fire and personal injury. Not suitable for children under 3 years. Choking hazard—small parts, small ball may be swallowed or inhaled. Keep it out of reach of children. !!Cleaning Attention Warning ››› ››› ››› Remove batteries before cleaning the battery compartment. Parts can only be wiped with a slightly damp cloth. Do not use cleaning agents.

SAFETY

Dear Parents and Supervising Adults,

This specialized kit makes it possible to investigate how natural resources such as wind can be used in Gigo mechanism by assembling each model to produce energy, or by transforming them from one form to another. These activities can stimulate children’s independent thinking, and furthermore lead children to discover how different types of energy are formed and where these energies can be applied in real life.

Before beginning these experiments, read through the instruction manual together with your child and discuss the safety information. Keep the packaging and instructions as they contain important information. Ensure the models have been assembled correctly, and assist your child with the experiments.

Only for use by children aged 8 years and older.

This product can help children explore and understand wind power in models and devices.

Before starting to assemble a model, please tell your children some precautions for using electricity.

Do not insert wires or other accessories into a household mains power outlet, this is extremely dangerous. This product is only suitable for use with AA rechargeable batteries (1.2-Volt, AA /HR6/KR6).

Safety for Experiments with Batteries:

No wires should be put in household electrical outlets. Never perform experiments using household current! The high voltage can be extremely dangerous or fatal!

To operate the models, you will need a AA rechargeable battery (1.2-volt, type AA, HR6/KR6, NiMH/NiCd ), which could not be included in the kit due to their limited shelf life.

The supply terminals are not to be short-circuited. A short circuit can cause the wires to overheat and the batteries to explode.

Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries.

Batteries are to be inserted with the correct polarity. Press them gently into the battery compartment. Always close battery compartments with the lid. Non-rechargeable batteries are not to be recharged. They could explode!

Rechargeable batteries are only to be charged under adult supervision. Rechargeable batteries must be removed from the device before being charged. Exhausted batteries are to be removed from the toy.

Dispose of used batteries in accordance with environmental provisions, not in the household trash. Be sure not to bring batteries into contact with coins, keys, or other metal objects. Avoid deforming the batteries.

As all of the experiments use batteries, have an adult check the experiments or models before use to make sure they are assembled properly.

Always operate the motorized models under adult supervision.

After you are done experimenting, remove the batteries from the battery compartments. Note the safety information accompanying the individual experiments or models!

Notes on Disposal of Electric and Electronic Components

The electronic components of this product are recyclable. For the sake of the environment, do not throw them into the household trash at the end of their lifespan.

They must be delivered to a collection location for electronic waste, as indicated by the following symbol: Please contact your local authorities for the appropriate disposal location.

2
››› ››› ››› ››› ›››
INFORMATION
››› ››› ››› ››› ››› ››› ››› ››› ››› ››› ››› ››› ››› ››› ››› ›››
What’s inside your experiment kit: 3 Checklist: Find – Inspect – Check off NO. Description QTY. Item No. 1 B-SHORT PEG 10 7344-W10-C2D 2 C-LONG PEG 10 7061-W10-C1R 3 C-STATIC AXLE CONNECTOR 20 1187-W10-E1K 4 C-LONG BUTTON FIXER 7 7061-W10-W2W 5 C-AXLE FIXING 1 3620-W10-A1D 6 C-WASHER 6 R12#3620 7 C-LATERAL CONVERTER 3 7061-W10-X1W 8 C-FRONT CONVERTER 1 7061-W10-Y1W 9 C-BASE GRID CONNECTOR 2 7026-W10-I1SK 10 C-LED (20mm) 1 7400-W85-F 11 O-ROUND HEAD SCREW M3*8 2 M20-12 12 C-20T GEAR 2 7026-W10-D2R 13 C-40T GEAR 3 7346-W10-C1B 14 C-60T GEAR 2 7026-W10-W5Y 15 C-3 HOLE ROD 4 7026-W10-Q2W 16 C-5 HOLE ROD 5 7413-W10-K2W 17 C-5 HOLE DUAL ROD 4 7413-W10-X1W 18 C-15 HOLE DUAL ROD 6 7413-W10-Z1W NO. Description QTY. Item No. 19 C-5X10 FRAME 3 7413-W10-I1W 20 C-5X15 FRAME 1 7413-W10-J1W 21 C-100mm AXLE Ⅱ 1 7413-W10-L2D 22 C-150mm AXLE Ⅰ 2 7026-W10-P1D 23 C-UNIVERSAL ADAPTER COVER 1 3680-W10-B1R 24 C-UNIVERSAL ADAPTER BODY 1 3680-W10-A1R 25 C-ROUND HUB 1 7324-W10-B1W 26 C-SHORT BLADE 6 7324-W10-C1B 27 C-LONG BLADE 3 7324-W10-A1W 28 E-410mm TUBE 1 1060-W17-410W 29 C-TUBE ADAPTER 2 7324-W10-E1W 30 C-BASE GRID 2 7125-W10-A1SK 31 C-1.5V DUAL BATTERY BOX II 1 7079-W85-A 32 C-30X MOTOR WITH WIRE CONNECTOR 1 7328-W85-A1-1 33 C-BATTERY BOX OPENER 1 7079-W10-B3TB 34 B-PEG REMOVER 1 7061-W10-B1Y 35 E-RELEASE PLIERS 1 1060-W85-M1G 36 O-250mm CABLE TIE 6 R40#3680 You will also need: 1 AA rechargeable battery (1.2-Volt, AA /HR6/KR6) ◾ Keep the instruction since it contains important information. KIT CONTENTS 1 12 21 29 5 16 25 33 9 20 3 14 23 31 7 18 27 35 112 13 22 30 6 17 26 34 104 15 24 32 8 19 28 36

1. Formation of Wind

How is “wind” formed? What are the functions of wind? How is wind utilized?

The Earth’s surface is surrounded by an atmosphere. Solar radiation is constantly landing on and passing through the atmosphere before it reaches the Earth. Because the Earth spins at an angle, different regions are subjected to different levels of solar heat. The different solar exposure causes changes in air pressure. Temperature is an important determining factor of air pressure, because relatively higher temperatures cause air to ascend, reducing air pressure. On the other hand, lower temperatures cause air to cool and descend, increasing air pressure. Another influence on temperature and air movement is the Earth’s rotation, which combines with the changes in air pressure. All these changes in air pressure causes movement in the air that we call wind.

Fig. 1 Cold/hot air convection caused by solar heat and the earth’s self-rotation leads to the formation of “wind”.

Humans began using wind power a very long time ago, for example, the Chinese and Persians used windmills for irrigation, water-collection, and grinding grain more than 1,000 years ago. European countries also used wind power, and the most famous example is Dutch windmills. People in Crete, a Greek Island, also used canvas windmills to fetch water. By the medieval period, windmills were an important energy source in Europe, and extensive research was being conducted using windmills. In 1890, meteorologists in Denmark created the first wind turbine, which began a new period of technological development. As wind turbine technology developed, wind power became increasingly effective.

Wind power continued to progress into the 20th century. In the early 1900s, wind power was still solely used for agricultural needs. It was not until the 1970s and the OPEC oil crisis when wind power was considered a way of producing electrical power. A lot of research on wind power to electrical power happened at that time. By 1990, with the assistance of significant government subsidies, wind power generators were beginning to be used. As fuel costs increase, alternative energy sources become more important, and wind power generation is one possible way of supplying energy needs.

4
Fig. 2 Shows the earliest conventional windmill, modern wind turbine, and wind farm (Data source: Bureau of Energy, MOEA).
CHECK IT OUT

CHECK IT OUT

Wind Force Scale

The wind force can be measured by observing the sea or land condition under wind effects, and represented based on the wind force scale. At present, the most common scale used internationally is the Beaufort Scale, which was created in 1805 by Sir Francis Beaufort, an Irish-born British admiral. The scale is firstly applied to observation on sea under wind forcing, and sequentially also applied to land. Via revisions over ages, the scale becomes standard as the table below:

The formula for actual wind speed and Beaufort Number is V= 0.836 * (B3/2 ) (B= Beaufort Number; V= Actual wind speed (m/s))

Beaufort Scale used for land observation

1-2 3-6 7-10 11-15 16-20 21-26 27-33 34-40 41-47 48-55 56-63 64

<0.2 0.3-1.5 1.6-3.3 3.4-5.4 5.5-7.9 8.0-10.7 10.8-13.8 13.9-17.1 17.2-20.7 20.8-24.4 24.5-28.4 28.5-32.6 32.7

breeze

Gentle breeze

Moderate breeze

breeze

Strong breeze

High wind, Moderate Gale,

Fresh Gale

Strong Gale

Gale/Storm

Violent storm

Gale

Calm. Smoke rises vertically.

Wind motion visible in smoke but not in vanes.

Wind felt on exposed skin. Leaves rustle. Vanes moved.

Leaves and smaller twigs in constant motion. Light flags extended.

Dust, leaves, and loose paper lifted. Small tree branches moved.

Small trees in leaf begin to sway.

Large branches in motion. Whistling heard in telegraph wires. Umbrella used with difficulties.

Whole trees in motion. Inconvenience felt when walking against wind.

Twigs broken off trees. Progress impeded.

Larger branches broken off trees, and some small trees blown over. Slight structural damage occurs, such as chimney collapsed.

Trees are broken off or uprooted. Considerable structural damage occurs.

Seldom experienced. Accompanied by wide-spread damage.

Maximum and extensive damage occurs. Very rarely encountered.

From the Beaufort Number 3-7, the wind is categorized as Gentle Breeze, Moderate Breeze, Fresh Breeze, Strong Breeze, and Near Gale (the actual wind speed is around 3-17m/s). These wind levels are applicable to wind generators.

Beaufort Number Wind speed kts m/s Description Wind Effects on Land 0 1 2 3 4 5 6 7 8 9 10 11 12-17 Calm Light air Light
Fresh
Whole
Hurricane-force
Near
<1
5

2. The Mysteries of Blade Design and Number

Traditional windmills come with more blades than a wind turbine, because windmills for grinding grain and wind turbines for generating power are very different. The cross section of windmill blades can vary widely, some are low efficiency and others are high efficiency.

The cross-section of a modern wind turbine blade is very similar to an airplane wing. They both have convex tops and flat bottoms, which creates a difference in air pressure. The faster air flow over the upper (convex) side creates a low pressure environment, and the slower air flow under the lower side has greater pressure. This is known as the Bernoulli Effect. The different air pressures generate a force in plane wings that we call lift, but on windmills and turbines, the force creates spin. The optimal curvature of the convex (and sometimes concave underside) of a wing is close to the shape of a water drop. This is because the water droplet is the shape least likely to create vortices in the air as it moves. Eddies and vortices in the air near a moving body lower efficiency. The shape of the wing in Gigo’s long and windmill blades all follow the principles described here, and these are taken from a the science of fluid mechanics.

Fig. 3 Dutch Windmills and water-pumping windmills in villages in central parts of the United States.

Most wind turbines in use today use a 3-blade design. Experimental findings have shown that the power generation capacity of fans with 6 blades is higher, particularly in low winds, but because the blades on a commercial turbine are about 120 meters long, the rotational torque on the mechanical part of the system can become too great when there are high winds or gusts. One key aspect of wind turbine design is managing the enormous rotational torque produced by such long blades. Consider, how would a wind turbine function in a typhoon?

Building the models in this set will show you how green energy wind turbines function, and some of the advantages and disadvantages of wind power. The model in this set can’t match full scale commercial wind turbines, but the functional principles are exactly the same.

generating wind

human engineer.

6
Fig. 7 An energy
turbine, relative to a
Fig. 5 Fig. 6 CHECK IT OUT Fig. 4 Lift Air-flow Resistance

Principle of Wind Power

Wind is a natural and best sustainable energy for its replenishment which helps reduce the consumption of fossil fuel. Due to the characteristics of cleanness, pollution free, and tourism potential of wind, and the mature development of technology, people manufacture wind for commercial purpose in recent years and make wind become the fastest growing recyclable energy. When wind turns windmill blades, torque is generated to accelerate the gearbox, power the generator, and then create wind power. The process shows how wind power is converted into mechanical power, and then turned into electrical power through generators. For house use, the electrical power needs a further transformation by transformers, and finally distributed to consumers via electricity transmission system. The real wind power generator belongs to the type of alternating current generators. Its electrical power has to be rectified into a direct current when stored in a battery.

4. Direct Current Generator

According to Fleming’s right hand rule, when the right index finger is pointing towards a magnetic field, the thumb is meanwhile indicating the motion direction of the conductor while the middle finger is showing the direction of the electrical current (positive charge of current). This is the principle behind power generator.

Fig. 10 The biggest difference between a direct current generator and an alternating current generator is the commutator connecting the coil, also known as “brushes” structure.

Flux EMF directionMotion Motion direction Flux direction Current direction Right hand Thumb, index and middle fingers mutually at right angles Rotor Blade Nacelle Hub Low-speed Shaft High-speed Shaft GearboxRotor Hub Brake Brake Generator Transformer Tower How Wind Power Works 1 2 4 5 6 7 8 9 3 10 11 12 13 14 15 1. Blades 2. Rotor 3. Pitch 4. Brake 5. Low-speed shaft 6. Gearbox 7. Generator 8. Controller 9. Anemometer 10. Wind Vane 11. Nacelle 12. High-speed shaft 13. Yaw drive 14. Yaw motor 15. Tower 7 Fig. 8 Fig. 9 3.
CHECK IT OUT

Similar to the alternating generator.

When the coil passes through the vertical position, the commutator changes the connecting direction of the coil and the external wiring, making the electric current outside of the coil always moving in a unidirection. When there is a conversion between the positive and negative charge in loop, the terminal block of the contactor interchanges as well, and thus the positive and negative voltage discharged from contactors are fixed, as shown in Fig. 12. This type of connecting-exchanging process is known as “commutation”. The rotatable semi-circle conductor as “commutator segments” and the position-fixing contactor as “brushes” set up the device of “commutator”.

5. Using a Motor as a Generator:

Different from the alternating generator.

Commutator

Current generated by a direct current generator:

During the coil’s rotation of one cycle, Current I is constantly changing.

cycle 1 cycle

Revere direction by the commutator

Coil position

The motor and generator share the same basic structure, and in other simpler words: Generator (motor) = current = (magnetic field action) = motion Generator = motion = (magnetic field action) = current Therefore, applying a current on a motor will create motion; on the other hand, applying motion on a motor will create a current!

cycle

I 1/2
Rotation
8 Fig. 11 Fig. 12
CHECK IT OUT

13

MOTOR

In this experiment, we use a special generator component, as shown in Figure 13. On its most right side, an axle is placed to rotate the input fans, and then the wind power generated by the fans

be transmitted via the gear A, B, C and D to the generator. Through the device, a train value is produced as:

GEARBOX = 30/8 × 28/8 × 20/8 = 32.8125

This indicates that when the axle for the input fan rotates at the speed of 1 rpm, the generator shaft will rotate at the speed of 32 rpm. If the rotation speed of the axle for the input fan achieves 100 rpm and that of the generator shaft accordingly becomes 3200 rpm, the generator can produce a 3V direct current (DC). The faster the rotation speed is, the higher the voltage of the produced current.

Principle of 1.5V DUAL BATTERY BOX

Fig. 14

Fig. 15 A diode is installed into the 1.5V DUAL BATTERY BOX.

A diode allows only unidirectional electric current. The electronic symbol (the arrow) indicates the permitted direction for the electric current to flow. Generally speaking, only if the electric current is a forward current with the voltage of 0.7V, it will be able to pass through the circuit. However, when the electric current flows in the counter direction (as in the case that the positive and negative poles of the solar panel or the wire connecter are set reversely), it will be blocked, which is showed by the electronic symbol.

Using the device under ideal conditions of wind speed, the wind turbine can be mobilized, and a current from the positive electrode of the wire passes into the positive electrode of the rechargeable battery in the battery charger and slowly charges the battery. As wind speed becomes too slow, the voltage from the power generation will reduce as well. However, a reverse current leakage will not take place since the diode in the battery charger functions as a protector. Keep the device under stable wind conditions and charge for 3-4 hours, the windmill can be activated for 50 minutes.

GENER ATOR 1N5 817 AA /R6 1. 2V D1 Generator C B AD Axle 9 6. Reverse Generator with Wire Connector 7.
Fig.
30X
WITH WIRE CONNECTOR
will
THE
CHECK IT OUT

TIPS AND TRICKS

Tips and Tricks for Building the Models

B

Fig. 16

Fig. 18

1. Use the end “A” of PEG REMOVER to pull off the LONG PEG (Fig. 16).

2. Use the end “B” of PEG REMOVER to pull off the LONG BUTTON FIXER (Fig. 17).

3. When fixing a gear or a tire onto the framework with a drive axle, be sure to keep a gap of about 1mm between the gear or the tire and the framework to decrease the friction caused in operation so that a smooth motion can be expected (Fig. 18).

4. Fix the ROUND HUB with your left hand and adjust the angles of the bottom end of the blade (Fig. 19).

5. How to take apart the UNIVERSAL ADAPTER from the ROUND HUB? Insert the end “B” of PEG REMOVER between the UNIVERSAL ADAPTER and the ROUND HUB, and tilt the UNIVERSAL ADAPTER to take them apart (Fig. 20).

How to Assemble and Disassemble TUBE ADAPTER and 410mm TUBE

Fig. 21

Push the TUBE ADAPTER into 410mm TUBE and turn the TUBE ADAPTER until a “click” is heard. They are then fixed together (Fig. 21).

Note: Do not hold the TUBE ADAPTER and the 410mm TUBE where you insert each piece as finger may be pinched (Fig. 21).

How to Insert Rechargeable Battery

1 23

Fig. 22

Put RELEASE PLIERS into holes that have safety lock pins coming through and squeeze the RELEASE PLIERS to release the 410mm TUBE and the TUBE ADAPTER (Fig. 22).

5

Open Insert the rechargeable battery to the battery holder.

Use BATTERY BOX OPENER to open the battery cover. Close the battery cover.Push

Fig. 23

B

Using the BATTERY BOX OPENER to open the 1.5V DUAL BATTERY BOX and using the end “B” of PEG REMOVER to remove the battery as Fig. 23 shows.

Done

WARNING: This product is only intended for use by rechargeable batteries.

SAFETY TOOL

Only for use by adults!

Fig. 20OK! (with gap) A Fig. 17 Fig. 19 B
10
+ 4

TIPS AND TRICKS

How to Adjust the Gearbox

Fig. 24

Hold the gearbox and the 60T GEAR you are to shift as shown in Fig. 24 and move this 60T GEAR backward so that it will mesh with the upper 20T GEAR, while the other two gear sets are left unmeshed, to adjust the gear ratio at 3:1.

Gearbox

Fig. 26

Gear Ratio 1:1

MOTOR WITH WIRE CONNECTOR

Fig. 25

Hold the gearbox and the 20T GEAR you are to shift as shown in Fig. 25 and move this 20T GEAR backward so that it will mesh with the upper 60T GEAR, while the other two gear sets are left unmeshed, to adjust the gear ratio at 1:3.

Gear Ratio 1:3

Fig. 27

Fig. 27 shows you only the upper 60T GEAR meshed with the lower 20T GEAR so that the current gear ratio is 1:3.

Gear Ratio 3:1

Fig. 28

Fig. 29

If you shift the gears so that only the upper and the lower 40T GEAR are meshed together the gear ratio of this gearbox will be changed to 1:1. (Fig. 28)

If you shift the gears so that only the upper 20T GEAR and the lower 60T GEAR are meshed together the gear ratio of this gearbox will be changed to 3:1. (Fig. 29)

30X
11

INDOOR

Setting up a Fan and the Windmill for Indoor Experiments

Industrial Fan

Industrial Fan

Household Fan

Household Fan

16"
The Windmill with Short Blades 57.5cm 6cm 100cm 112cm 100cm 94cm 57.5cm 6cm 100cm 57.5cm94cm 100cm 57.5cm112cm 12
EXPERIMENTS 18"
16"
The Windmill with Long Blades The Windmill with Long Blades The Windmill with Short Blades 18"
Please refer to these instructions to properly set up a fan in order to conduct experiments with your wind turbines indoors.
Fig. 30 Fig. 32 Fig. 31 Fig. 33

SETTING UP THE WINDMILLS

Outdoors

Fixing the windmill on a bamboo rod with 2 CABLE TIE (Fig. 34).

Fastening the CABLE TIE to ensure the windmill is immovable (Fig. 35).

35

Indoors

Press the Gearbox with your hand (Fig. 36) while fixing the windmill base to the ground with tapes (Fig. 37).

Putting two iron blocks or stones with the weight of 1.3 Kgs for each on the base to further fix the windmill (Fig. 38).

The experiment of power generation can be run by fingers under the condition without wind in doors.

Hold the windmill with the left hand and rotate it with a right finger (Fig.39 & 40).

13
Fig. 34 Fig. 36 Fig. 39 Fig. 40 Fig. 37 Fig. 38 Fig.

LET’S DO SOME

Experiment 1: Adjust the Gear Ratio of Gigo Gearbox

Use a windmill with SHORT BLADE (Fig. 42) to observe the variation of power generation (the brightness of the LED bulb) under the same wind speed. Fix the angles of the blades and change the gear ratios by shifting the gears at the lower axle.

Fig. 41 shows you the upper 60T GEAR meshed with the lower 20T GEAR so that the current gear ratio of this gearbox is 1:3.

Select Gear Ratio 1:1 in Experiments 2-4

Experiment 2:

Use a windmill with SHORT BLADE (Fig. 42) to observe the variation of power generation under different wind speeds (wind levels of a fan). Do you figure out any correlation between wind speed and power generation (the brightness of the LED bulb)?

Experiment 3:

Use a windmill with SHORT BLADE (Fig. 42) to observe the variation of power generation (the brightness of the LED bulb) under the same wind speed. Change the angles of the blades. Can you find the best and most efficient angle to make the LED brightest?

Experiment 4:

Use a windmill with SHORT BLADE (Fig. 42) to observe the variation of power generation (the brightness of the LED bulb) under the same wind speed. Change the blade numbers (6 blades, 4 blades, 3 blades, 2 blades). Note to arrange the blades in symmetry with equal intervals. Can you find the best and most efficient blade numbers to make the LED brightest?

Experiment 5:

Use the windmill with LONG BLADE (Fig. 44) and repeat Experiments 1-3. Can you also find the best and most efficient conditions for this new device?

14
EXPERIMENTS! 30X MOTOR WITH WIRE CONNECTOR Gear Ratio 1:3 30X MOTOR WITH WIRE CONNECTOR Gear Ratio 1:1 Fig. 41 Fig. 43 Fig. 42 Fig. 44

Make sure the switch on the 1.5V DUAL BATTERY BOX is set to IN (charge).

Plant Can be

Make sure the switch on the 1.5V DUAL BATTERY BOX is set to IN (charge).

After the Windmill is

To activate the windmill, toggle the switch to OUT (discharge).

To activate the windmill, toggle the switch to OUT (discharge).

Fasten Its Base with Heavy Objects/Bricks.

How to charge a battery by using the windmill:

1. Remove the LED and connect the wire connectors to the 1.5V DUAL BATTERY BOX. Make sure the switch on the 1.5V DUAL BATTERY BOX is toggled to IN (charge).

2. Adjust the blade to the optimized angle obtained in the earlier experiment.

3. Secure the rechargeable batteries (below AA, HR6/KR6, NiMH/NiCd 1.2-volt 1200mAh). Do not use rechargeable batteries with excessive charging values; otherwise, the results will not be apparent.

Note: Never use a non-rechargeable AA battery in the 1.5V DUAL BATTERY BOX, there is a risk of overheating and explosion!

4. Utilize natural wind outdoors or an electric fan at home to blow the windmill and allow the batteries to be charged.

IN OUT OUTIN 15 STORING THE GENERATED ELECTRICITY With the Following Experiment, a Mini Power
Built. Fig. 45 Fig. 46
Assembled, Securely

ADVANCED

Fig. 47

5. When set to OUT, the 1.5V DUAL BATTERY BOX will discharge and activate the windmill in case there is no wind.

6. Interestingly, the fast-rotating windmill slows down when rechargeable batteries are inserted. It is a normal phenomenon because the flat batteries constitute an ultra high capacitance. The effect is negligible like water being poured into a large pond. As the voltage slowly increases after sometime, the windmills will start to rotate.

7. Under a normal wind speed (5.5m/s), charging for 2.5hr can activate the windmill for 40 minutes.

8. There will be an extended charging time as wind speeds vary. The varied voltages will form a voltage pulses that enhance the charging capacity. No risk of overcharging will take place if left unattended over a long period of time. (Since the wind turbine voltage under wind speed 4m/s is about 4.5. In case of excessive winds, the windmill blade will detach and reduce in the rotation speed due to the centrifugal force).

Advanced Reference I

Fig. 48

Adjust the angle using the angle meter (draw up the angle values on paper in advance in place of matching)

Fig. 49

Since the LED brightness cannot be quantified, use a Digital Multi-Meter (DMM) to test the relationship between model voltage and blade angle after removing the LED light.

16
REFERENCE
0 5 10 15 20 25 30 0 0.6 1.01 2.39 2.42 2.16 1.88 0 1.2 2.72 3.51 4.05 3.04 2.44 Blade angle (with the ultra shaft and included angle of the universal connector as basis) 16” Industrial electric fan 14” Stand fan 10 0 -10 1.40 1.73 1.55 1.56 2.10 1.65 1.9 1.76 1.6 2.5 1.89 The straight side of fans with 3 LONG BLADE and the included angle of the UNIVERSAL ADAPTER serve as the gear ratio basis: 3:1 Gear ratio: 1:1 16” Industrial electric fan 14” Stand fan 16” Industrial electric fan 14” Stand fanAngle not rotating 0 30 60 90 150 0.5V 0.9V 1.39V 1.40V 0 10 20 30 40 1.41V 1.31V 1.28V 1.25V 0.48V Charging Time (Min) Battery Testing (AA 1.2V 700mAh) Charging Time (Min) Battery Testing (AA 1.2V 700mAh) Charging Test Discharging Test 4.5 4 3.5 3 2.5 2 1.5 1 0.5 0 50 0 0.6 1.01 2.72 3.51 4.05 3.04 2.24 1.882.16 2.42 2.39 1.2 10 15 20 3025 2.50 2.00 1.50 1.00 0.50 0.00 10 0 -10 1.40 1.56 1.73 1.55 1.65 2.10 1.6 1.4 1.2 1 0.8 0.6 0.4 0.2 0 20 40 60 80 100 Charging Voltage Voltage (V) Time (min) Voltage test of wind power rechargeable ER Diagram of 6-blade fan angle vs. power generation voltage 14” Stand fan 14” Stand fan Discharging Voltage 16” Industrial electric fan 16” Industrial electric fan Voltage (V) Voltage (V) Fan blade Angle 17 ADVANCED REFERENCE Testing of fans with 3 LONG BLADE Result Diagram of the Charging Experiment ER Diagram of Blade Angle Change vs. Voltage Change for Fans with 6 SHORT BLADE. The Strongest Industrial Electric Fan 6 SHORT BLADE. Optimized Conditions (20 degrees)` Fig. 50 Fig. 51 Fig. 53 Fig. 52 Conclusion: The experimental values show that short fan blade angles (20 degrees) obtain optimized results. The experimental values show that long blade fans (degree) obtain optimized results. Perform a charging test after electrically discharging the AA, KR6, NiCd 1.2V 700mAh rechargeable battery.

Advanced Reference II

An Analysis on Fan Blade Angle vs. Power Generation Capacity.

Quantitative Analysis is adopted to verify the optimum blade angle through a measuring instrument. In “Experiment 3: Is There Any Change in Power Generation Capacity (Change in Brightness of LED Lights) for Wind Turbines with Short Blades? Can You Find the Best Fan Blade Angle?" the LED light on/off and brightness are determined by the power generation voltage. When it is lower than 1.7V, the LED light will not turn on and a higher voltage will produce a brighter LED light. The higher the rotational speed of the turbine is, the higher the voltage will be (distal shaft). Thus, fixed test conditions such as fixed wind speed are called controlled variables, the blade angle is the independent variable, and the voltage output is the dependent variable.

Fig. 54

ADVANCED REFERENCE

Fig. 55

Measuring Instrument (Not Included This Kit.)

From the left:

Anemometer

Digital Multi-Meter (DMM)

Tachometer

Angle meter

Fig. 56

Reference for Parents and Instructors:

1. All the experiments above adopt “Quantitative Analysis.” Three variables are included: the fixed conditions of each experiment are called “controlled variables”. “Dependent variables” represent experimental outcomes and “independent variables” are those factors assumed to have an effect on dependent variables.

2. Under different testing conditions, the best experimental result can be derived from repeatedly experiments on different independent variables. Since the result is for the “optimized design” and has to been obtained from variant experiments, it is highly beneficial for kids to develop their ability on problem solving and truth seeking.

3. In the case to measure the correlation between wind speeds and power generation (the brightness of the LED bulb), it is difficult to concretely quantified the result and make it data-based only upon the brightness of the LED bulb.

For more accurate record, a multi-meter is suggested to be used for measuring voltage changes (DC-V).

4. This teaching aid for wind generation is excellent for experiments and happy learning either outdoors with natural wind or indoors with an electric fan.

18
30X MOTOR WITH WIRE CONNECTOR Gear Ratio 1:3 30X MOTOR WITH WIRE CONNECTOR Gear Ratio 1:3 Strong Middle Weak Wind Speed Blades Turning LED Lighted3 SHORT BLADE Gear Ratio 1:1 Strong Middle Weak Wind Speed Blades Turning LED Lighted4 SHORT BLADE Gear Ratio 1:1 Strong Middle Weak Wind Speed Blades Turning LED Lighted6 SHORT BLADE Gear Ratio 1:1 Strong Middle Weak Wind Speed Blades Turning LED Lighted3 LONG BLADE Gear Ratio 1:1 Strong Middle Weak Wind Speed Blades Turning LED Lighted2 SHORT BLADE Gear Ratio 1:1 Strong Middle Weak Wind Speed Blades Turning LED Lighted3 SHORT BLADE Gear Ratio 1:1 Strong Middle Weak Wind Speed Blades Turning LED Lighted4 SHORT BLADE Gear Ratio 1:1 Strong Middle Weak Wind Speed Blades Turning LED Lighted6 SHORT BLADE Gear Ratio 1:1 Strong Middle Weak Wind Speed Blades Turning LED Lighted3 LONG BLADE Gear Ratio 1:1 19 TESTING RESULTS Testing Results by 16" Household Fan Testing Results by 18" Industrial Fan 16" Household Fan 18" Industrial Fan
Strong Middle Weak Wind Speed Blades Turning LED Lighted6 SHORT BLADE Gear Ratio 1:3 Strong Middle Weak Wind Speed Blades Turning LED Lighted3 LONG BLADE Gear Ratio 1:3 Strong Middle Weak Wind Speed Blades Turning LED Lighted6 SHORT BLADE Gear Ratio 3:1 Strong Middle Weak Wind Speed Blades Turning LED Lighted2 SHORT BLADE Gear Ratio 1:3 Strong Middle Weak Wind Speed Blades Turning LED Lighted3 SHORT BLADE Gear Ratio 1:3 Strong Middle Weak Wind Speed Blades Turning LED Lighted4 SHORT BLADE Gear Ratio 1:3 Strong Middle Weak Wind Speed Blades Turning LED Lighted6 SHORT BLADE Gear Ratio 1:3 Strong Middle Weak Wind Speed Blades Turning LED Lighted3 LONG BLADE Gear Ratio 1:3 Strong Middle Weak Wind Speed Blades Turning LED Lighted2 SHORT BLADE Gear Ratio 3:1 Strong Middle Weak Wind Speed Blades Turning LED Lighted3 SHORT BLADE Gear Ratio 3:1 Strong Middle Weak Wind Speed Blades Turning LED Lighted4 SHORT BLADE Gear Ratio 3:1 Strong Middle Weak Wind Speed Blades Turning LED Lighted6 SHORT BLADE Gear Ratio 3:1 20 TESTING RESULTS
Parts Needed 21 WINDMILL WITH LONG-BLADE 1Model 1 12 29 5 16 25 9 20 3 14 23 31 7 27 11 2 13 22 30 6 1710 4 15 24 32 8 19 28 1 5 3 2 ×34 ×26 x 9 x 3 x3 x 1 x 18 x 2 x 2 x 2 x 1 x 1 x 1 x 1x 1 x2 x 3 x 4 x 10 x 1 x 1 x2 x 1 x 1 x 2 x 3 x 6 x 1 x 5 x 2 x 2 B C D A
D D B C B B 22 WINDMILL WITH LONG-BLADE1Model 11 13 7 9 12 8 10 Side view 150mm 150mm 14
G G F E Long leg Long leg Short leg Short leg T IP 23 WINDMILL WITH LONG-BLADE 1Model 21 15 17 19 22 16 18 20 E F

the LED(20mm) does not power up, try inserting the LED(20mm) again, but in the opposite direction.

If
Only the gears closest to the motor mesh. Insert a rechargeable battery. A rechargeable battery is required. Remove the LED(20mm). Toggle the switch to IN. 24 Done! Done! Use charging mode The blades should spin clockwise, and the LED(20mm) will light up. T IP 23 24 A 1 2 3 4 5 TEST THE MODEL WINDMILL WITH LONG-BLADE1Model
Parts Needed 25 WINDMILL WITH SHORT-BLADE 2Model 1 29 5 9 20 3 23 72 22 30 64 24 32 8 19 28 x 9 x 3 x 6 x 18 x2 x 2 x 1 x 1x 6 x 1 x 2 x 3x 10 x 1 x 1 x 7 x 1 x 2 x 3 x 6 x 1 x 2 1 3 2 26 18 The frame and gears for Model 2 are identical to Model 1. To build the frame and gears, see Model 1, steps 1 and steps 4 through 22. ×6 12 161411 13 1710 15 x 1 x 2 x 4x2 x 5 x 2

Only the gears closest to the motor mesh.

If the wind power is low, try meshing the blue gears in the middle, rather than the gears closest to the motor.

The blades should spin clockwise,

LED(20mm)

light up.

If the LED(20mm) does not power up, try inserting the LED(20mm) again, but in the opposite direction.

26 WINDMILL WITH SHORT-BLADE2Model 5 4 Done!
and the
will
T IP TEST THE MODEL
Parts Needed 27 GLIDER 3Model 21 1 6 8 3 2 7 5 100mm 1 123 1411 134 16 20 23 22 17 24 1918 3226 31 x 6 x 2 x 4 x 3 x 1 x 1 x 1x 2 x 1 x 1 x 2 x 11 x 2 x 2 x 2 x 5 x 4 x 2 x 1 4 ×2 ×2 B C A
C C 28 GLIDER3Model 12 14 10 13 15 9 11 150mm 150mm Done! IP B B Front view Toggle the switch to OUT. A
Parts Needed 1 ×3 A B 29 SAIL CAR 4Model 21 1 123 14 134 16 22 1918 3226 31 x 2 x 2 x 3 x 2 x 1 x 1x 3 x 3 x 3x 5 x 1 x 13 x 3 x 2 x 2 x 2 x 1 7 15 8 6 32 5 4 150mm 100mm
150mm 30 SAIL CAR4Model 11 7 9 8 10 Done! IP Toggle the switch to OUT. B A A A
Parts Needed A B B 31 TRICYCLE 5Model 21 1 123 1411 13 16 20 2322 17 24 1918 3231 x 6 x 2 x 6 x 3 x 1 x 1 x 1 x 1 x 1 x 2 x 16 x 2 x 1 x 2 x 4 x 2 x 2 x 1 15 53 7 9 6 4 8 10 1 2 B C ×2 ×2
Done! IP Toggle the switch to OUT. A A D D C 32 TRICYCLE5Model 11 15 13 17 12 16 14 150mm 100mm 150mm
Parts Needed A 33 JET CAR 6Model 1 5 32 6 4 150mm 21 1 123 1413 16 20 22 17 1918 3231 x 1 x 2 x 5 x 3 x 1 x 1 x 1 x 1 x 2 x 18 x 2 x 1 x 2 x 1 x 2 15 B
IP Toggle the switch to OUT. Done! A B 34 JET CAR6Model 11 7 9 8 10 150mm 100mm
Parts Needed A A A B D C 35 TRACTOR 7Model 7 5 3 7 2 6 100mm 1 ×2 4 ×2 21 1 123 1413 16 20 22 17 1918 3231 x 2 x 2 x 6 x 3 x 1 x 1 x 1 x 1 x 2 x 20 x 2 x 2 x 2 x 5 x 3 x 2 15 C B
IP Toggle the switch to OUT. Done! 36 TRACTOR7Model 11 13 9 12 8 10 150mm 150mm C D
Parts Needed 1 1 2 2 2100mm 37 RACE CAR 8Model 5 3 7 2 6 4 8 7 21 1 123 1413 16 20 22 17 1918 3231 x 1 x 2 x 6 x 3 x 1x 2 x 1 x 1 x 1 x 2 x 18 x 3x 2 x 2 x 4 x 5 x 4 x 2 15 26 4 1 ×2 9 ×2 A B C
IP Toggle the switch to OUT. Done! D C D D B A A 38 RACE CAR8Model 11 15 13 12 16 14 150mm 150mm 10 ×2 Front view
© 2022 Genius Toy Taiwan Co., Ltd. ALL RIGHTS RESERVED R21#7079

Turn static files into dynamic content formats.

Create a flipbook
Issuu converts static files into: digital portfolios, online yearbooks, online catalogs, digital photo albums and more. Sign up and create your flipbook.