98554184 21v1 l

1st Edition

21V1-L(A)

SERVICE MANUAL S9811421V1L(A)

COLOUR TELEVISION Chassis No. GA6 Chassis No. GA6

MODEL

21V1-L(A)

In the interests of user safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts indentical to those specified should be used.

CONTENTS

Page

IMPORTANT SERVICE SAFETY PRECAUTION ................................................................................................... 1-1 LOCATION OF USER’S CONTROL ...................................................................................................................... 2-1 INSTALLATION AND SERVICE INSTRUCTIONS ................................................................................................. 3-1 SERVICE MODE ..................................................................................................................................................... 4-1 ADJUSTMENT METHOD ........................................................................................................................................ 5-1 WAVEFORMS ......................................................................................................................................................... 6-1 CHASSIS LAYOUT ................................................................................................................................................. 7-1 BLOCK DIAGRAM .................................................................................................................................................. 8-1 DESCRIPTION OF SCHEMATIC DIAGRAM .......................................................................................................... 9-1 SCHEMATIC DIAGRAMS ......................................................................................................................................10-1 PRINTED WIRING BOARD ASSEMBLIES ........................................................................................................... 11-1 Parts Guide

ELECTRICAL SPECIFICATIONS POWER INPUT............................AC 110-220 V, 50/60 Hz POWER RATING .....................................................77W PICTURE SIZE .............................1,239 cm2(192sq inch) CONVERGENCE ............................................. Magnetic SWEEP DEFLECTION .................................. .. Magnetic FOCUS ........................................................ Electrostatic INTERMEDIATE FREQUENCIES Picture IF Carrier Frequency ...................... 45.75 MHz Sound IF Carrier Frequency ...................... 41.25 MHz Color Sub-Carrier Frequency ......................42.17 MHz (Nominal) AUDIO POWER OUTPUT RATING... ...................... 3.0 W(RMS) x 1pc

SHARP CORPORATION

SPEAKER SIZE ........................................................ 5 x 9cm, 1pc VOICE COIL IMPEDANCE .................16 ohm at 400 Hz ANTENNA INPUT IMPEDANCE VHF/UHF ........................................75 ohm Unbalanced TUNING RANGES VHF-Channels ................................................. 2 thru 13 UHF-Channels ................................................14 thru 69 CATV Channels ............................................. 1 thru 125 (EIA, Channel Plan U.S.A.)

Specifications are subject to change without prior notice.

This document has been published to be used for after sales service only.

The contents are subject to change without notice.

21V1-L(A)

CHAPTER 1. IMPORTANT SERVICE SAFETY PRECAUTION Service Manual TV E Market 21V1-L(A)

IMPORTANT SERVICE SAFETY PRECAUTION

Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and the servicing guidelines which follow:

WARNING

X-RADIATION AND HIGH VOLTAGE LIMITS

1. For continued safety, no modification of any circuit should be attempted.

2. Disconnect AC power before servicing.

3. Semiconductor heat sinks are potential shock hazards when the chassis is operating.

4. The chassis in this receiver has two ground systems which are separated by insulating material. The nonisolated (hot) ground system is for the B+ voltage regulator circuit and the horizontal output circuit. The isolated ground system is for the low B+ DC voltages and the secondary circuit of the high voltage transformer.

To prevent electrical shock use an isolation transformer between the line cord and power receptacle, when servicing this chassis.

1. Be sure all service personnel are aware of the procedures and instructions covering X-radiation.

The only potential source of X-ray in current solid state TV receivers is the picture tube. However, the picture tube does not emit measurable X-Ray radiation, if the high voltage is as specified in the "High Voltage Check" instructions.

It is only when high voltage is excessive that Xradiation is capable of penetrating the shell of the picture tube including the lead in the glass material.

The important precaution is to keep the high voltage below the maximum level specified.

2. It is essential that servicemen have available at all times an accurate high voltage meter.

The calibration of this meter should be checked periodically.

3. High voltage should always be kept at the rated value −no higher. Operation at higher voltages may cause a failure of the picture tube or high voltage circuitry and;also, under certain conditions, may produce radiation in exceeding of desirable levels.

4. When the high voltage regulator is operating properly there is no possibility of an X-radiation problem.

Every time a color chassis is serviced, the brightness should be tested while monitoring the high voltage with a meter to be certain that the high voltage does not exceed the specified value and that it is regulating correctly.

5. Do not use a picture tube other than that specified or make unrecommended circuit modifications to the high voltage circuitry.

6. W h e n t r o u b l e s h o o t i n g a n d t a k i n g t e s t measurements on a receiver with excessive high voltage, avoid being unnecessarily close to the receiver.

Do not operate the receiver longer than is necessary to locate the cause of excessive voltage.

SERVICING OF HIGH VOLTAGE SYSTEM AND PICTURE TUBE When servicing the high voltage system, remove the static charge by connecting a 10k ohm resistor in series with an insulated wire (such as a test probe) between the picture tube ground and the anode lead. (AC line cord should be disconnected from AC outlet.)

1. Picture tube in this receiver employs integral implosion protection.

2. Replace with tube of the same type number for continued safety.

3. Do not lift picture tube by the neck.

4. Handle the picture tube only when wearing shatterproof goggles and after discharging the high voltage anode completely.

1–1

21V1-L(A)

IMPORTANT SERVICE SAFETY PRECAUTION (Continued) BEFORE RETURNING THE RECEIVER (Fire & Shock Hazard) Before returning the receiver to the user, perform the following safety checks.

1. Inspect all lead dress to make certain that leads are not pinched or that hardware is not lodged between the chassis and other metal parts in the receiver.

2. Inspect all protective devices such as non-metallic control knobs, insulating materials, cabinet backs, adjustment and compartment covers or shields, isolation resistor-capacity networks, mechanical insulators, etc.

3. To be sure that no shock hazard exists, check for leakage current in the following manner.

• Plug the AC cord directly into a 110~220 volt AC outlet, (Do not use an isolation transformer for this test).

• Using two clip leads, connect a 1.5k ohm, 10 watt resistor paralleled by a 0.15µF capacitor in series with all exposed metal cabinet parts and a known earth ground, such as electrical conduit or electrical ground connected to earth ground.

• Use an AC voltmeter having with 5000 ohm per volt, or higher, sensitivity to measure the AC voltage drop across the resistor.

• Connect the resistor connection to all exposed metal parts having a return to the chassis (antenna, metal cabinet, screw heads, knobs and control shafts, escutcheon, etc.) and measure the AC voltage drop across the resistor.

AII checks must be repeated with the AC line cord plug connection reversed. (If necessary, a nonpolarized adapter plug must be used only for the purpose of completing these check.)

Any current measured must not exceed 0.5 milliamp.

Any measurements not within the limits outlined above indicate of a potential shock hazard and corrective action must be taken before returning the instrument to the customer.

DVM AC SCALE 1.5k ohm 10W

TO EXPOSED METAL PARTS

CONNECT TO KNOWN EARTH GROUND

SAFETY NOTICE Many electrical and mechanical parts in television receivers have special safety-related characteristics.

These characteristics are often not evident from visual inspection, nor can protection afforded by them be necessarily increased by using replacement components rated for higher voltage, wattage, etc.

Replacement parts which have these special safety characteristics are identified in this manual; electrical components having such features are identified by " " and shaded areas in the Replacement Parts Lists and Schematic Diagrams.

1–2

For continued protection, replacement parts must be identical to those used in the original circuit. The use of substitute replacement parts which do not have the same safety characteristics as the factory recommended replacement parts shown in this service manual, may create shock, fire, X-radiation or other hazards.

21V1-L(A)

CHAPTER 2. LOCATION OF USER'S CONTROL Service Manual TV E Market 21V1-L(A)

2–1

21V1-L(A)

CHAPTER 3. INSTALLATION AND SERVICE INSTRUCTIONS Service Manual TV E Market 21V1-L(A)

INSTALLATION AND SERVICE INSTRUCTIONS Note:

(1) When performing any adjustments to resistor controls and transformers use non-metallic screwdrivers or TV alignment tools.

(2) Before performing adjustments, the TV set must be on at least 15 minutes.

CIRCUIT PROTECTION

HIGH VOLTAGE CHECK

The receiver is protected by a 3.15A fuse (F701), mounted on PWB-A, wired into one side of the AC line input.

High voltage is not adjustable but must be checked to verify that the receiver is operating within safe and efficient design limitations as specified checks should be as follows:

X-RADIATION PROTECTOR CIRCUIT TEST After service has been performed on the horizontal deflection system, high voltage system, B+ system, test the X-Radiation protection circuit to ascertain proper operation as follows: 1. Apply 110~220V AC using a variac transformer for accurate input voltage.

2. Allow for warm up and adjust all customer controls for normal picture and sound.

3. Receive a good local channel.

4. Connect a digital voltmeter to P603 pin3 and make sure that the voltmeter reads 20 Âą1.1V. 5. Apply external 27V DC at P603 pin3 by using an external DC supply, TV must be shut off.

6. To reset the protector, unplug the AC cord and make a short circuit between P603 pin1 and P603 pin2.

Now make sure that normal picture appears on the screen.

7. If the operation of the horizontal oscillator does not stop in step 5, the circuit must be repaired before the set is returned to the customer.

3–1

1. Connect an accurate high voltage meter between ground and anode of picture tube.

2. Operate receiver for at least 15 minutes at 110~220V AC line voltage, with a strong air signal or a properly tuned in test signal.

3. Enter the service mode and set Y-mute ON by using Service R/C. 4. The voltage should be approximately 28.7kV (at zero beam).

If a correct reading cannot be obtained, check circuitry for malfunctioning components. After the voltage test, make Y-mute off to the normal mode.

21V1-L(A)

CHAPTER 4. SERVICE MODE Service Manual TV E Market 21V1-L(A)

SERVICE MODE Service Mode Overview 1.

2.

3.

4.

5.

Service mode is entered by SERVICE key input or CH-UP +VOL-DOWN input during reset.

Service mode is cleared by entering SERVICE key command during service mode.

If key input port (SERVICE) input is LOW, then it is in service mode.

During key input port (SERVICE) input is LOW, clearing service mode by key input SERVICE is disabled.

Service mode can be switched to 4 modes as follows by key input MENU;

Adjustment mode

First mode of service mode when SERVICE key is pressed.

Setting mode

Check mode

First mode of service mode when local key CH-UP + VOL-DOWN is pressed after MCU reset.

Option mode

6. AFT processing is disabled during service mode. PLL setting data is set to fo data.

7. All user data are set to default during service mode. FAO and SPEAKER user settings are off and on respectively in service mode. Energy Save is off.

8. Sleep timer, View timer, on timer and off timer are inactivated in Service mode.

9. Sound is muting in service mode except at Adjustment Items V20, M01, M03, M04, M05, and M06.

4–1

21V1-L(A)

Adjustment Mode Items No. V01 V02 V03 V04 V05 V06 V07 V08 V09 V10 V11 V12 V13 V14 V15 V16 V17 V18 V19 V20 V21 M01 M02 M03 M04 M05 M06

Item Name SUB-PICTURE SUB-TINT SUB-COLOR SUB-BRIGHT SUB-SHARP V-SHIFT H-SHIFT RF-AGC V-SIZE PIF-VCO R-CUTOFF G-CUTOFF B-CUTOFF R-DRIVE B-DRIVE SUB-COLOR(YUV) SUB-TINT(YUV) CC-POS SCREEN CUT OFF SUB-VOL H-VCO MTS-ATT MTS-VCO MTS-FILTER MTS-WIDEBAND MTS-SPECTRAL SUB-VOL

IC 1 Chip 1 Chip 1 Chip 1 Chip 1 Chip 1 Chip 1 Chip 1 Chip 1 Chip 1 Chip 1 Chip 1 Chip 1 Chip 1 Chip 1 Chip 1 Chip 1 Chip MICON 1 Chip 1 Chip 1 Chip MTS MTS MTS MTS MTS MTS

Register CONTRAST TINT COLOR BRIGHT VIDEO-TONE V-SHIFT H-PHASE RF-DELAY V-SIZE VIF-VCO R-CUTOFF G-CUTOFF B-CUTOFF R-DRIVE B-DRIVE COLOR BASEBAND-TINT CC-POS CUT OFF A-ATT H-VCO ATT (MTS) VCO (MTS) FILTER (MTS) WIDEBAND (MTS) SPECTRAL (MTS) VOL (MTS)

4–2

Range 0~127 0~127 0~127 0~255 0~63 0~7 0~31 0~127 0~63 0~63 0~255 0~255 0~255 0~127 0~127 0~127 0~127 0~255 0~2 0~127 0~7 0~15 0~63 0~63 0~63 0~63 0~63

Default 127 64 64 128 32 4 16 127 32 32 127 127 127 64 64 64 64 32 0 127 4 10 32 28 27 32 63

21V1-L(A)

SELF ADJUSTMENT H-VCO 1.

2.

3.

4.

5.

6.

7.

When there is H-VCO self-adjustment key input for adjustment item H-VCO, self-adjustment is performed.

H-FREE(1chip) is set to 1.

H-OUT is set by intelligent monitor output.

IM input is set as TIM input.

H-VCO(1chip) data is changed so that the number of input pulse is 125 inside 8ms interval.

When adjustment completed, OSD display and H-VCO self-adjustment status data of EEPROM are updated.

H-FREE(1chip), intelligent monitor output and IM input mode are recovered.

RF-AGC 1.

2.

3.

4.

When there is RF-AGC self-adjustment key input for adjustment item RF-AGC, self-adjustment is performed.

AGC-OUT is set by intelligent monitor output.

IM input is set as AD input.

By decreasing RF-AGC (1chip) data from current RF-AGC adjustment value to 0, AFT input voltage becomes the maximum setting value.

5. Increase RF-AGC(1chip) data, when AFT input voltage is at (max. 0.3V) point, adjustment is completed.

6. When adjustment completed, OSD display and RF-AGC self-adjustment status data of EEPROM are updated.

7. Intelligent monitor output and IM input mode are recovered.

PIF-VCO 1.

2.

3.

4.

5.

6.

7.

When there is PIF-VCO self-adjustment key input for adjustment item PIF-VCO, self-adjustment is performed.

VIF-DEF(1chip) is set to 1.

AFC is set by intelligent monitor output.

IM input is set as AD input.

VIF-VCO(1chip) data is changed so that input voltage becomes 2.5V. When adjustment completed, OSD display and PIF-VCO self-adjustment status data of EEPROM are updated.

VIF-DEF(1chip), intelligent monitor output and IM input mode are recovered.

4–3

21V1-L(A)

Setting Mode Items No. F01 F02 F03 F04 F05 F06 F07 F08 F09 F10 F11 F12 F13 F14 F15 F16 F17 F18 F19 F20 F21 F22 F23 F24 F25 F26 F27 F28 F29 F30 F31 F32 F33 F34 F35 F36 F37 F38 F39 F40 F41 F42 F43 F44 F45 F46 F47 F48 F49 F50 F51 F52 F53 F54

Item Name VIDEO TONE -GAIN (TV) VIDEO TONE -GAIN (AV) VIDEO TONE -GAIN (S-AV) VIDEO TONE -GAIN(YUV) ABCL BS ABCL-G SHP-AV SHP-SAV SHP-YUV RGB-CLIP E-SAVE FAO-VOL PIF-G Y-DELAY(TV) Y-DELAY(AV) Y-DELAY(SAV) Y-DELAY(YUV) TINT-AV TINT-SAV COL-AV COL-SAV R-DRI(R2) R-DRI( R) R-DRI(B) B-DRI(R2) B-DRI( R) B-DRI(B) V-FREE GAMMA TRAP(TV) TRAP(AV) H-FREE 1W(TV) 1W(AV) YLPF BS-D BS-C SL(TV) SL(AV) SL(SAV) SL(YUV) AFC2 VD(TV) VD(AV) AS(TV) AS(AV) AS(SAV) AS(YUV) FBP(TV) FBP(AV) FBP(SAV) FBP(YUV) C.CLIP LEVEL

IC 1 Chips 1 Chips 1 Chips 1 Chips 1 Chips 1 Chips 1 Chips OFFSET OFFSET OFFSET 1 Chips OFFSET 1 Chips 1 Chips 1 Chips 1 Chips 1 Chips 1 Chips OFFSET OFFSET OFFSET OFFSET OFFSET OFFSET OFFSET OFFSET OFFSET OFFSET 1 Chips 1 Chips 1 Chips 1 Chips 1 Chips 1 Chips 1 Chips 1 Chips 1 Chips 1 Chips 1 Chips 1 Chips 1 Chips 1 Chips 1 Chips 1 Chips 1 Chips 1 Chips 1 Chips 1 Chips 1 Chips 1 Chips 1 Chips 1 Chips 1 Chips 1 Chips

4–4

Register V-TONE V-TONE V-TONE V-TONE ABCL BS-OFF ABCL-G VIDEO-TONE(OFFSET) VIDEO-TONE(OFFSET) VIDEO-TONE(OFFSET) EXTRGB-CLIP CONTRAST(OFFSET) A-ATT VIF-GAIN Y-DELAY Y-DELAY Y-DELAY Y-DELAY TINT(OFFSET) TINT(OFFSET) COLOR(OFFSET) COLOR(OFFSET) R-DRI(OFFSET) R-DRI(OFFSET) R-DRI(OFFSET) B-DRI(OFFSET) B-DRI(OFFSET) B-DRI(OFFSET) V-FREE GAMMA TRAP-FINE TRAP-FINE H-FREE V.WINDOW V.WINDOW YSW-LPF BS-DISCHARGE BS-CHARGE S-SLICE DOWN S-SLICE DOWN S-SLICE DOWN S-SLICE DOWN AFC2-G VSYNC-DET VSYNC-DET AUTO-SLICE AUTO-SLICE AUTO-SLICE AUTO-SLICE FBP VTH FBP VTH FBP VTH FBP VTH C.CLIP LEVEL

Range 0/1 0/1 0/1 0/1 0/1 0/1 0/1 -16~+16 -16~+16 -16~+16 0/1 0~63 0~127 0~7 0~7 0~7 0~7 0~7 -32~+32 -32~+32 -32~+32 -32~+32 -32~+32 -32~+32 -32~+32 -32~+32 -32~+32 -32~+32 0/1 0~3 0~3 0~3 0/1 0/1 0/1 0/1 0~3 0~3 0~3 0~3 0~3 0~3 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1

Default 0 0 0 0 0 0 0 0 0 0 0 30 120 4 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 2 2 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

21V1-L(A)

Setting Mode Items (Continued) No. F55 F56 F57 F58 F59 F60 F61 F62 F63 F64 F65 F66 F67 F68 F69 F70

Item Name PSW FAO-VOL CP CC LEVEL OSD POS OFFSET-ADJ-COL OFFSET-ADJ-TINT OFFSET-ADJ-TINT-YUV TIMER4-LOW SPEED TIMER4-HIGH SPEED R-CUT-YUV G-CUT-YUV B-CUT-YUV R-DRI-YUV B-DRI-YUV CLOCK-ADJ

IC MTS MTS PLL MICON MICON 1 Chips 1 Chips 1 Chips 1 Chips 1 Chips 1 Chips 1 Chips 1 Chips 1 Chips 1 Chips 1 Chips

4–5

Register PSW VOL CHARGE PUMP CC LEVEL OSD POS COLOR TINT BASEBAND-TINT TIMER4 VALUE TIMER4 VALUE R-CUT(OFFSET) G-CUT(OFFSET) B-CUT(OFFSET) R-DRI(OFFSET) B-DRI(OFFSET)

Range 0/1 0~63 0/1 0/1 0/1 -32~+32 -32~+32 -32~+32 0~225 0~225 -63~+63 -63~+63 -63~+63 -63~+63 -63~+63 0~25

Default 0 60 0 0 0 0 0 0 50 125 0 0 0 0 0 25

21V1-L(A)

Option Mode Items No 001 002 003 004 005 006 007 008 009 010 011 012 013 014 015 016 017 018 019 020 021 022 023 024 025 026 027 028 029 030

OPTION FUNCTION DEMO DOWNLOAD V-CHIP SPEAKER FAO P.PREF UNIV+ VIEW TIMER EZ-SETUP PON-CH FAV-COL COMPONENT AV AV2 MTS TONE-CTRL AUTO-OFF INIT-LANG SETUP-FLAG AV-FR AV3/S-IN COMB AUTO-INPUT CLOCK LED FLAT BASS BOOST DSE SRS WHITE-OUT

0 1 Without DEMO With DEMO Without V-CHIP OP With V-CHIP OP Without V-CHIP With V-CHIP Without SPEAKER With SPEAKER Without FAO With FAO Without P.REF With P.REF Without UNIV+ With UNIV+ Without VIEW TIMER With VIEW TIMER EZ-SETUP AUTO PRESET Without POWER-ON With POWER-ON FAV-COL COL-TEMP Without COMPONENT With COMPONENT Without AV With AV AV1 system AV2 system Without MTS With MTS Without S-ADJ With S-ADJ Without AUTO-OFF With AUTO-OFF ENGLISH SPANISH NO SET UP AUTO SET UP "0"=NO AV "1"=REAR "2"=FRONT "3"=REAR & FRONT Without AV3/S-IN With AV3/S-IN Without COMB With COMB Without AUTO-INPUT With AUTO-INPUT Without CLOCK With CLOCK SEMEX MODEL SPC MODEL Not FLAT MODEL FLAT MODEL Without BASS BOOST With BASS BOOST Without DSE With DSE Without SRS With SRS Without WHITE-OUT With WHITE-OUT

Default Data 1 0 0 1 1 1 1 1 0 0 1 1 1 1 1 1 1 1 1 3 0 0 1 1 0 1 0 0 0 1

Check Mode Micron mask version, software version and ROM correction function status are displayed in check mode.

4–6

21V1-L(A)

CHAPTER 5. ADJUSTMENT METHOD Service Manual TV E Market 21V1-L(A)

Memory Map Data Caution: to get into the service mode, one of the ways is press direct key for service items.

There is three stage of Service Mode data First stage data from V01 ~ M06 to go into second stage of service mode data, press MENU key Second stage data from F01 ~ F101 to go into third stage of service mode data, press MENU key Third stage data from O01 ~ O34 Below is the contents of these data First Stage Data V01 V02 V03 V04 V05 V06 V07 V08 V09 V10 V11 V12 V13 V14 V15 V16 V17 V18 V19 V20 V21 V22 V23 V24 V25 V26 V27 V28 V29 M01 M02 M03 M04 M05 M06

Service Mode SUB-PICTURE SUB-TINT SUB-COLOR SUB-BRIGHT SUB-SHARP V-SHIFT H-SHIFT RF-AGC V-SIZE V-SHIFT50 H-SHIFT50 V-SIZE50 PIF-VCO R-CUTOFF G-CUTOFF B-CUTOFF R-DRIVE B-DRIVE SUB-COLOR(YUV) SUB-TINT(YUV) CC-POS SCREEN CUT OFF SUB-VOL H-VCO S-TRAP VS-CORRECT

Function CONTRAST TINT COLOR BRIGHT VIDEO-TONE V-SHIFT H-PHASE RF-DELAY V-SIZE V-SHIFT(OFFSET) H-PHASE(OFFSET) V-SIZE(OFFSET) VIF-VCO R-CUTOFF G-CUTOFF B-CUTOFF R-DRIVE B-DRIVE COLOR BASEBAND-TINT CC-POS CUT OFF A-ATT H-VCO S-TRAP FINE ADJ VS-CORRECTION VS-CORRECT OFFSET VS-CORRECTION V LINEARITY V-LINEARITY V LINEARITY OFFSET V-LINEARITY MTS-ATT ATT (MTS) MTS-VCO VCO (MTS) MTS-FILTER FILTER (MTS) MTS-WIDEBAND WIDEBAND (MTS) MTS-SPECTRAL SPECTRAL (MTS) SUB-VOL VOL (MTS)

Auto Adjustment Item 1. H-VCO 2. RF-AGC 3. PIF-VCO

5–1

Range 0~127 0~127 0~127 0~255 0~63 0~7 0~31 0~127 0~63 -7~+7 -15~+15 -31~+31 0~63 0~255 0~255 0~255 0~127 0~127 0~127 0~127 0~255 0~2 0~127 0~7 0~15 0~63 -13~+13 0~63 -13~+13 0~15 0~63 0~63 0~63 0~63 0~63

Default Data 127 64 64 128 41 4 16 127 32 0 0 0 32 127 127 127 64 64 64 64 32 0 127 4 7 36 0 35 0 10 32 28 27 32 63

21V1-L(A)

Second Stage Data Service Mode SHPG F01 SHPG-P F02 SHPG-N3 F03 ABCL F04 BS F05 ABCL-G F06 SHP-AV F07 SHP-YUV F08 SHP-P F09 SHP-N3 F10 RGB-CLIP F11 E-SAVE F12 FAO-VOL F13 PIF-G F14 Y-DELAY(TV) F15 Y-DELAY(AV-P) F16 Y-DELAY(TV-N3) F17 Y-DELAY(AV) F18 Y-DELAY(AV-P) F19 Y-DELAY(AV-N3) F20 Y-DELAY(YUV) F21 TINT-AV F22 COL-AV F23 COL-P F24 COL-N3 F25 R-DRI(R2) F26 R-DRI( R) F27 R-DRI(B) F28 B-DRI(R2) F29 B-DRI( R) F30 B-DRI(B) F31 V-FREE F32 GAMMA F33 H-FREE F34 1W(TV) F35 1W(AV) F36 YLPF F37 BS-D F38 BS-C F39 SL(TV) F40 SL(AV) F41 SL(YUV) F42 AFC2 F43 VD(TV) F44 VD(AV) F45 VD(YUV) F46 AS(TV) F47 AS(AV) F48 AS(YUV) F49 FBP(TV) F50 FBP(AV) F51 FBP(YUV) F52 C.CLIP LEVEL F53 PSW F54 FAO-VOL F55 CP F56 CC LEVEL F57 OSD POS-H F58 OSD POS-V50 F59 OSD POS-V60 F60 OFFSET-ADJ-COL F61

Function V-TONE V-TONE V-TONE ABCL BS-OFF ABCL-G VIDEO-TONE(OFFSET) VIDEO-TONE(OFFSET) VIDEO-TONE(OFFSET) VIDEO-TONE(OFFSET) EXTRGB-CLIP CONTRAST(OFFSET) A-ATT VIF-GAIN Y-DELAY Y-DELAY Y-DELAY Y-DELAY Y-DELAY Y-DELAY Y-DELAY TINT(OFFSET) COLOR(OFFSET) COLOR(OFFSET) COLOR(OFFSET) R-DRI(OFFSET) R-DRI(OFFSET) R-DRI(OFFSET) B-DRI(OFFSET) B-DRI(OFFSET) B-DRI(OFFSET) V-FREE GAMMA H-FREE V.WINDOW V.WINDOW YSW-LPF BS-DISCHARGE BS-CHARGE S-SLICE DOWN S-SLICE DOWN S-SLICE DOWN AFC2-G VSYNC-DET VSYNC-DET VSYNC-DET AUTO-SLICE AUTO-SLICE AUTO-SLICE FBP VTH FBP VTH FBP VTH C.CLIP LEVEL PSW VOL CHARGE PUMP CC LEVEL OSD POS OSD POS OSD POS COLOR

5–2

Range 0/1 0/1 0/1 0/1 0/1 0/1 -16~+16 -16~+16 -31~+31 -31~+31 0/1 0~63 0~127 0~7 0~7 0~7 0~7 0~7 0~7 0~7 0~7 -32~+32 -32~+32 -31~+31 -31~+31 -32~+32 -32~+32 -32~+32 -32~+32 -32~+32 -32~+32 0/1 0~3 0/1 0/1 0/1 0/1 0~3 0~3 0~7 0~7 0~7 0/1 0~3 0~3 0~3 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0~63 0/1 0~31 0~31 1~55 1~50 -32~+32

Default Data 0 0 0 0 0 0 0 0 0 0 0 30 120 5 5 5 5 5 5 5 0 +6 0 +24 0 +8 +3 -2 -18 -8 +6 1 1 0 0 1 0 0 0 2 2 0 0 3 2 0 1 1 0 0 0 0 0 0 58 1 0 0 38 23 +10

21V1-L(A)

F62 F63 F64 F65 F66 F67 F68 F69 F70 F71 F72 F73 F74 F75 F76 F77 F78

OFFSET-ADJ-TINT TINT OFFSET-ADJ-TINT-YUV BASEBAND-TINT WAIT MD TIME (SLOW MODE) R-CUT-YUV R-CUT(OFFSET) G-CUT-YUV G-CUT(OFFSET) B-CUT-YUV B-CUT(OFFSET) R-DRI-YUV R-DRI(OFFSET) B-DRI-YUV B-DRI(OFFSET) CONTRAST OFFSET CONTRAST (OFFSET) CONTRAST YUV OFFSET CONTRAST (OFFSET) BRIGHT OFFSET BRIGHT (OFFSET) [0Ah D7...D0] BRIGHT AV2 OFFSET BRIGHT (OFFSET) [0Ah D7...D0] BRIGHT YUV OFFSET BRIGHT (OFFSET) [0Ah D7...D0] TRAP TRAP-FINE TRAP-P TRAP-FINE TRAP-N3 TRAP-FINE AFC1-Gain-TV AFC1-G

F79

AFC1-Gain-AV

F80

AFC1-Gain-YUV

F81 F82 F83 F84 F85 F86 F87 F88 F89 F90 F91 F92 F93 F94 F95 F96 F97 F98

OM-DET BS-Gain C-ANGLE V-AGC V-STD-TV V-STD-AV V-STD-YUV HALF-H KILLER V-DL U-DL CTI Adj MCUVOUT AS-SPEED-DN AS-SPEED-UP CR-PEDESTEL-ADJ CB-PEDESTEL-ADJ SIF-BPF-WIDE COL-SYSTEM

AFC1 Gain Up 2 AFC1-G AFC1 Gain Up 2 AFC1-G AFC1 Gain Up 2 OM-Det BS-Gain C.ANGLE V AGC V STD DETOFF V STD DETOFF V STD DETOFF HALF-H KILLER V-DL Fine U-DL Fine CTI MCU VOUT AS-SPEED-DN AS-SPEED-UP Cr Pedestal Adj. Cb Pedestal Adj. SIF BPF WIDE COL-SYSTEM

F99 F100 F101

Pow-Storage SIF45 GAIN DOWN S-TRAP OFF

SIF45 GAIN DOWN S-Trap

5–3

-32~+32 -32~+32 0/1 -63~+63 -63~+63 -63~+63 -63~+63 -63~+63 -63~+63 -63~+63 -63~+63 -15~+15 -63~+63 0~3 0~3 0~3 0~3

+2 0 1 0 0 0 0 0 0 0 0 +1 0 2 2 2 0

0~3

3

0~3

3

0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0~3 0~3 0/1 0/1 0/1 0/1 0~15 0~15 0~3 0: 11XX (AUTO) 1: 0011 (PAL-M) 2: 0111 (PAL-N) 3: 0110 (N358) 0/1 0/1 0/1

0 0 0 0 0 0 0 1 0 0 1 0 0 0 8 8 1 3

1 0 1

21V1-L(A)

Third stage Data OPTION FUNCTION DEMO O01 DOWNLOAD O02 V-CHIP O03 SPEAKER O04 FAO O05 P.PREF O06 UNIV+ O07 VIEW TIMER O08 EZ-SETUP O09 * PON-CH O10 FAV-COL O11 COMPONENT O12 AV O13 AV2 O14 MTS O15 TONE-CTRL O16 AUTO-OFF O17 LAST POWER O18 SETUP-FLAG O19 AV-FR O20 AV3/S-IN O21 COMB O22 AUTO-INPUT O23 CLOCK O24 LED O25 FLAT O26 BASS BOOST O27 DSE O28 SRS O29 WHITE-OUT O30 O31 FORCE-COL O32

H-SYNC JUDGE

O33

INIT-LANG

DATA = " 0" DEMO DISABLE V-CHIP OP DISABLE V-CHIP DISABLE SPEAKER DISABLE FAO DISABLE P.REF DISABLE UNIV+ DISABLE VIEW TIMER DISABLE EZ-SETUP POWER-ON DISABLE FAV-COL COMPONENT DISABLE AV DISABLE AV1 MTS DISABLE S-ADJ DISABLE AUTO-OFF DISABLE STANDBY MODE NO SET UP

DATA =" 1"

Default Data 1 0 0 1 1 1 0 1 0 0 1 1 1 1 1 1 1 POWER OFF CH 0 AUTO SET UP 1 "0"=NO AV "1"=REAR "2"=FRONT "3"=REAR & FRONT 3 AV3/S-IN DISABLE ENABLE 0 COMB DISABLE ENABLE 0 AUTO-INPUT DISABLE ENABLE 1 CLOCK DISABLE ENABLE 1 SEMEX MODEL SPC MODEL 0 FLAT DISABLE ENABLE 1 BASS BOOST DISABLE ENABLE 0 DSE DISABLE ENABLE 0 SRS DISABLE ENABLE 0 WHITE-OUT DISABLE ENABLE 1 Disable Enable 0 Disable

Enable

1

0 1 2 Range: 1 … 7

0

ENGLISH SPANISH PORTUGUESE O34 LANG-SEL Bit 0: Spanish Bit 1: French Bit 2: Portuguese * POWER ON BY CH-UP / DOWN KEY.

5–4

ENABLE ENABLE ENABLE ENABLE ENABLE ENABLE ENABLE ENABLE AUTO PRESET ENABLE COL-TEMP ENABLE ENABLE AV2 ENABLE ENABLE ENABLE

7

21V1-L(A) MODEL NAME ADJ US TMENT ITEM ADJ US TMENT P OS ITION 䋭 CONTROL

P RE-ADJ US T REQUIREMENT

CONTENT INP UT CONDITION OUTP UT

21V1-L(A) OP TION S ET UP REFER AS BELOW

䋭 21V1-L(A) OS D CHECKING FOR THIRD S TAGE S ERVICE DATA

FUNCTION

O01

21V1-L(A) DEF

1

BUS OP TION

FUNCTION

DEMO

O02 0

O12

21V1-L(A)

1

0

FUNCTION

O21

O22

21V1-L(A)

0

0

21V1-L(A) DEF

S YMBOL

0

SP

FAO

0

0

P .P REF UNIV+

0

0

VIEW

EZ

P ON-CH

1

0

1

"1"=ENABLE "1"= AUTO P RES ET

FOR THIRD S TAGE S ERVICE DATA O11

FUNCTION

O03 O04 O05 O06 O07 O08 O09 O10

DOWNLOAD V-CHIP

"0"= DIS ABLE 009 --> "0"= EZ-S ETUP

FAV-COL

HIS TORY OF REVIS ION

REFER AS BELOW

䋭

BUS OP TION

ADJ US TMENT P ROCEDURE

S TEP RANGE

AV3

O31

COMP

COMB

O32

O13 O14 O15 O16 O17 O18 O19 O20 AV

AV2

MTS

TONE

AUTO

1

1

0

0

1

La st P ow S ETUP

0

1

AV-FR

3

O23 O24 O25 O26 O27 O28 O29 O30 A-IN

CLOCK

LED

FLAT

BAS S

DS E

S RS

WHITE

0

0

1

0

0

0

0

0

O33

O34

FORCE COL

H-S YNC

INITIAL LAN

LANG-S EL

0

1

1

1

O11 --> "0" =FAV-COL "1"= COL-TEMP O19--> "0"= NO S ET UP "1" = AUTO S ETUP O20--> "0"=NO AV "1"=REAR "2"=FRONT "3"=REAR&FRONT O25--> "0"= S EMEX S P EC "1" = S P C S P EC O33 --> "0"= ENGLIS H "1"= S P ANIS H "2"=P ORTUGUES E O34--> "1" ENGLIS H + S P ANIS H

REVIS ED CONTENT .

5–5

21V1-L(A)

MODEL NAME ADJ US TMENT ITEM ADJ US TMENT P OS ITION 䋭 CONTROL

P RE-ADJ US T REQUIREMENT

CONTENT INP UT CONDITION OUTP UT

21V1-L(A) BUS S ET UP REFER AS BELOW

䋭

OS D CHECKING

FUNCTION 21V1-L(A) DEF

FUNCTION 21V1-L(A) DEF

HIS TORY OF REVIS ION

REFER AS BELOW

䋭

DATA S ETUP ADJ US TMENT P ROCEDURE

S TEP RANGE

S YMBOL

FOR FIRS T AND S ECOND S TAGE S ERVICE DATA V25 S -TRAP 0

F23

V26

V28

F14 P IF-G

Y-DELAY (TY-N3)

TINT-AV

41

33

4

3

-5

VS COR

F58

V-LIN

F62

F17

F73

F22

F83

COL-AV

OS D P OS -H

OFFS ET ADJ TINT

BRIGHT AV2 OFFS ET

C ANGLE

+5

5

+5

+3

1

REVIS ED CONTENT .

5–6

21V1-L(A) MODEL NAME ADJ US TMENT ITEM

21V1-L(A)

H-P OS ITION

ADJ US TMENT P OS ITION CONTROL

V07

S TEP RANGE

0-31

I2C BUS CONTROL

P RE-ADJ US T OP TION S ET UP, BUS S ET UP,CRT-P URITY REQUIREMENT CONTENT

US 4 CH LION HEAD (MONOS COP E)

INP UT CONDITION

AC 220V, US MAGNETIC FIELD

OUTP UT

CONFIRMATION BY CRT S CREEN 1.ADJUST THE V07 BUS DATA TO HAVE A BALANCE POSITION TO SPEC OF A=B. 2.IF CANNOT MAKE IT TO A=B, ADJ FROM THE BEST POINT SO THAT B SLIDELY SMALLER THAN A

ADJ US TMENT P ROCEDURE

A

B

[CHECKING SPEC] LEFT AND RIGHT S YMMETRICAL

HIS TORY OF REVIS ION

S YMBOL

REVIS ED CONTENT .

5–7

21V1-L(A) 21V1-L(A)

MODEL NAME ADJ US TMENT ITEM

V-S IZE

ADJ US TMENT P OS ITION CONTROL

V09

S TEP RANGE

0~63

I2C CONTROL

P RE-ADJ US T OP TION S ET UP , BUS S ET UP ,CRT P URITY, V-P HAS E , +B ADJ US T REQUIREMENT CONTENT

US 4 CH LION HEAD

INP UT CONDITION

AC 220

OUTP UT

CONFIRMATION BY CRT S CREEN ADJUST THE V09 BUS DATA UNTILL THE OVERSCAN BECOME AS SPECIFIED BELOW. CAUTION:- PLEASE AGING TV MORE THAN 10 MINUTES BEFORE ADJUSTMENT.

ADJ US TMENT P ROCEDURE

[CHECKING SPEC] OVERS CAN 10 ± 2.5%

HIS TORY OF REVIS ION

S YMBOL

REVIS ED CONTENT .

5–8

21V1-L(A) MODEL NAME ADJ US TMENT ITEM

21V1-L(A)

V-P HAS E

ADJ US TMENT P OS ITION CONTOROL

V06

S TEP RANGE

I2C CONTROL

P RE-ADJ US T OP TION S ET UP , BUS S ET UP , CRT P URITY REQUIREMENT CONTENT

US 4 CH LION HEAD (MONOS COP E P ATTERN)

INP UT CONDITION

220 V, RF INP UT, ZERO MAGNETIC FIELD

OUTP UT

CONFIRMATION ON CRT S CREEN ADJUST V06 BUS DATA TO HAVE A MOST ACCEPTABLE VERTICAL POSITION. THE MONOSCOPE PATTERN SHOULD BE BALANCE IN VERTICAL POSITION NOTE: THE DATA FOR V06 LIMIT AT <= 04 , EVEN POSITION NOT GOOD ENOUGH

ADJ US TMENT P ROCEDURE

[CHECKING CONFIRMATION ]

HIS TORY OF REVIS ION

S YMBOL

REVIS ED CONTENT .

5–9

0-7

21V1-L(A)

21V1-L(A)

MODEL NAME ADJ US TMENT ITEM

CLOS ED CAP TION S ET UP

ADJ US TMENT P OS ITION CONTROL

V21

S TEP RANGE

0 - 255

I2C CONTROL

P RE-ADJ US T OP TION S ET UP , BUS S ET UP REQUIREMENT CONTENT

US 4 CH LION HEAD

INP UT CONDITION

AC 220

OUTP UT

CONFIRMATION ON CRT DIS P LAY. 1) BY SELECTING THE V21, BOX BLK TEXT WILL BE APPEARED. 2) ADJUST THE V21 BUS DATA TO HAVE A BALANCE POSITION TO SPEC OF A=B.

ADJ US TMENT P ROCEDURE

TEXT BOX BLK

B

A

[CHECKING SPEC] LEFT AND RIGHT S YMMETRICAL THEN V21 DATA REDUCE 5 S TEP .

HIS TORY OF REVIS ION

S YMBOL

REVIS ED CONTENT .

5 – 10

21V1-L(A)

MODEL NAME ADJ US TMENT ITEM ADJ US TMENT P OS ITION CONTROL P RE-ADJ US T REQUIREMENT CONTENT INP UT CONDITION OUTP UT

ADJ US TMENT P ROCEDURE

21V1-L(A)

H-VCO V24

S TEP RANGE

I2C CONTROL OP TION S ET UP , BUS S ET UP NO S IGNAL (RAS TER) CONDITION AC 220 IC 801 P IN 15 (MANUAL ADJ) 1)GO TO SERVICE MODE, 2)GO TO SERVICE DATA V24, ADJ UNTIL FREQ AS BELOW (SELF ADJ) 1) GO TO SERVICE MODE, BY SELECTING THE SERVICE DATA V24 2) PRESS THE R/C TO OPERATE AUTO H-VCO, OSD APPEAR "OK" AT SCREEN 3) IF APPEAR "NG" PLS REPEAT STEP 2

[CHECKING SPEC] FREQ = 15.735 ± .02 KHz

HIS TORY OF REVIS ION

0-7

S YMBOL

REVIS ED CONTENT .

5 – 11

21V1-L(A) MODEL NAME ADJ US TMENT ITEM

21V1-L(A)

P IF-VCO

ADJ US TMENT P OS ITION CONTROL

V13

S TEP RANGE

0 - 63

I2C CONTROL

P RE-ADJ US T OP TION S ET UP , BUS S ET UP REQUIREMENT CONTENT

NO S IGNAL (RAS TER) CONDITION

INP UT CONDITION

AC 220

OUTP UT

ADJ US T P ROCEDURE

CONFIRMATION ON CRT DIS P LAY(AUTO), IC801 P IN 9 VOLTAGE (MANUAL).

(AT SELF ADJUSTMENT MODE) 1)GO INTO S ERVICE MODE,BY S ELECTING THE S ERVICE DATA V13 2)PRESS THE R/C FOR AUTO PIF-VCO KEY, OSD APPEAR "OK" AT SCREEN 3)IF AP P EAR "NG" P LS REP EAT S TEP 2 (AT MANUAL ADJ US TMENT MODE) 1)GO INTO S ERVICE MODE, BY S ELECTING THE S ERVICE DATA V13

2) ADJ US T THE DATA UP /DOWN UNTIL IC801 P IN 9 VOLTAGE BECOME AS S P ECIFIED BELOW

[CHECKING SPEC] 2.5 ± 0.5 V DC (CHECKING S P EC : 2.50 ± 1.5 V)

HISTORY OF REVISION

S YMBOL

REVIS ED CONTENT .

5 – 12

21V1-L(A)

MODEL NAME ADJ US TMENT ITEM

21V1-L(A)

RF-AGC

ADJ US TMENT P OS ITION CONTROL

V08

S TEP RANGE

0-127

I2C CONTROL

P RE-ADJ US T OP TION S ET UP , BUS S ET UP REQUIREMENT CONTENT

US 10CH HALF COLOR BAR

INP UT CONDITION

RF INP UT FIELD S TRENGTH53d BǴV(FIX)

OUTP UT

TUNER AGC TERMINAL (J A442 OR TP 201) OR CRT DIS P LAY CONFIRMATION (AT SELF ADJUSTMENT MODE) 1.GO TO SERVICE MODE 2.GO TO SERVICE DATA V08, PRESS R/C TO OPEARATE AUTO-AGC KEY AND CONFIRM THE OK DISPLAY ON THE SCREEN. 3.IF APPEAR NG PLS REPEAT STEP 2 AGAIN. (AT MANUAL ADJUSTMENT MODE)

ADJ US TMENT P ROCEDURE

1.ADJUST THE V08 BUS DATA UNTIL AGC TERMINAL VOLTAGE BECOME MAXIMUM, THEN DROP 0.1V BELOW MAXIMUM VOLTAGE. 2. CHANGE THE ANTENNA INPUT SIGNAL TO 63~67 dBuV, AND MAKE SURE THERE IS NO NOISE 3. CHANGE THE ANTENNA INPUT SIGNAL TO 90~95 dBuV TO BE SURE THAT THERE IS NO CROSS MODULATION BEAT.

[VOLTAGE CONFIRMATION ] MAX - 0.1V dc

HIS TORY OF REVIS ION

S YMBOL

REVIS ED CONTENT .

5 – 13

21V1-L(A) 21V1-L(A)

MODEL NAME ADJ US TMENT ITEM

S CREEN

ADJ US TMENT P OS ITION CONTROL

V14,V15,V16

S TEP RANGE

0~255

I2C CONTROL

P RE-ADJ US T OP TION S ET UP , BUS S ET UP REQUIREMENT CONTENT

WINDOW P ATTERN OR US 4CH LION HEAD

INP UT CONDITION

220 V

OUTP UT

CONFIRMATION ON CRT DIS P LAY.

1) IN SERVICE MODE, SET V04 TO 127 AND V14&V15&V16 TO 127; V17&V18 TO 64 , GET IN YMUTE BY R/C AND SET V22 TO "1", PICTURE APPEAR IN CUT-OFF CONDITION 2)ADJUST THE SCREEN SO THAT CUT-OFF LINE APPEAR IN LOW BRIGHT, THEN JUDGE THAT WHETHER THE CUT-OFF LINE APPEAR IN RED OR GREEN OR BLUE COLOR, IN THIS CONDITION V14= R-CUTOFF,V15=G-CUTOFF,V16=B-CUTOFF, FIX THE DATA OF THE COLOR APPEAR IN CUTOFF LINE AND USE R/C TO ADJUST THE OTHER TWO CUT-OFF DATA SO THAT CUT-OFF LINE COLOR BECOME WHITE. ADJ US TMENT 3)TURN THE SCREEN VR OF FBT SO THAT CUT-OFF LINE JUST DISAPPEAR AND USE R/C TO P ROCEDURE SET V22 TO "0", NEXT DISABLE THE Y-MUTE SO THAT PICTURE APPEAR IN NORMAL MODE.

[VOLTAGE CONFIRMATION ]

HIS TORY OF REVIS ION

S YMBOL

REVIS ED CONTENT .

5 – 14

21V1-L(A) 21V1-L(A)

MODEL NAME ADJ US TMENT ITEM

WHITE BALANCE

ADJ US TMENT P OS ITION CONTROL

S TEP RANGE

V17,V18,V14,V15,V16

0-127, 0~255

I2C BUS CONTROL

P RE-ADJ US T OP TION S ET UP , BUS S ET UP , S CREEN REQUIREMENT CONTENT

23CH 50IRE WINDOW P ATTERN

INP UT CONDITION

220 V

OUTP UT

ADJ US TMENT P ROCEDURE

CRT S CREEN DIS P LAY .

1) WHITE (HIGH BEAM) FIRS T LET THE GUN P OINT AT BLACK P OS ITION (AS DRAWING ATTACH), ADJ V04 UNTIL BRIGHTNES S Y BECOME 5 c d /m 2 , THEN LET THE GUN P OINT AT WHITE P OS ITION (AS DRAWING ATTACH),ADJ US TVO1 UNTIL BRIGHTNES S Y BECOME 150 c d /m 2, ADJ US T THE BUS DATA OF V17(R DRIVE),V18(B DRIVE) UNTLL THE AXIS OF COLOUR TEMP ERATURE BECOME X=0.273,Y=0.280.

2) BLACK(LOW BEAM) LET THE GUN P OINT AT BLACK P OS ITION, IF THE VALUE S HIFTED AWAY FROM THE DATA ADJ US TED IN S TEP 1), ADJ US T AGAIN THE TWO S ERVICE DATA WHICH HAVE CHOS EN AT S CREEN ADJ US T S O THAT TO OBTAIN THE S IMILAR AXIS AS ABOVE. *WARNING: DO NOT DIS TURB THE MINI S TEP GUN DATA DURING THIS ADJ US TMENT. **REP EAT S TEP 1),2) TO GET A REGULATED P OS ITION. WHITE

US14

[CHECKING CONFIRMATION ] X=0.273,Y=0.280 (11,600° K+1 MP CD)

HIS TORY OF REVIS ION

S YMBOL

REVIS ED CONTENT .

5 – 15

BLACK

21V1-L(A)

21V1-L(A)

MODEL NAME ADJ US TMENT ITEM

S UB-BRIGHT

ADJ US TMENT P OS ITION CONTROL

V04

S TEP RANGE

0-255

I2C CONTROL

P RE-ADJ US T OP TION S ET UP , BUS S ET UP , S CREEN, WHITE BALANCE REQUIREMENT CONTENT INP UT CONDITION OUTP UT

WINDOW P ATTERN 220 V

CRT S CREEN DIS P LAY .

1)LET THE GUN POINT AT BLACK POSITION(AS ATTACH DRAWING), ADJUST V04 BUS DATA UNTILL BRIGHTNESS Y = 0.5 cd/m2, THEN STEP DOWN MORE 4 STEP

ADJ US TMENT P ROCEDURE

BLACK

US14

[VOLTAGER CONFIRMATION ] BRIGHTNESS Y = 0.5 cd/m2, THEN STEP DOWN MORE 4 STEP HIS TORY OF REVIS ION

S YMBOL

REVIS ED CONTENT .

5 – 16

21V1-L(A)

21V1-L(A)

MODEL NAME ADJ US TMENT ITEM

S UB-P ICTURE

ADJ US TMENT P OS ITION CONTROL

V01

S TEP RANGE

0-127

I2C BUS CONTROL

P RE-ADJ US T OP TION S ET UP , BUS S ET UP , S CREEN, WHITE BALANCE, S UB-BRIGHTNES S REQUIREMENT CONTENT INP UT CONDITION OUTP UT

WINDOW P ATTERN 220 V CRT S CREEN DIS P LAY 1) LET THE GUN POINT AT WHITE POSITION (AS ATTACH DRAWING), ADJUST V01 BUS DATA UNTILL BRIGHTNESS Y = 150 cd/m2.

NOTE: ALLOWABLE DATA FOR V01 IS >= 90, EVEN Y CAN'T MATCH THE SPEC

ADJ US TMENT P ROCEDURE

WHITE

US14

[VOLTAGE CONFIRMATION ] BRIGHTNES S Y = 150 cd/m2

HIS TORY OF REVIS ION

S YMBOL

REVIS ED CONTENT .

5 – 17

21V1-L(A)

21V1-L(A)

MODEL NAME ADJ US TMENT ITEM

S UB-TINT

ADJ US TMENT P OS ITION CONTROL

V02

S TEP RANGE

I2C CONTROL

P RE-ADJ US T OP TION S ET UP , BUS S ET UP , VCO ADJ , RF-AGC REQUIREMENT CONTENT

US 10 CH HALF COLOR BAR P ATTERN

INP UT CONDITION

220 V

OUTP UT

B-AMP TR BAS E (J A410) CONFIRRM WITH OS CILLOS COPE 1)GET IN Y-MUTE FUNCTION BY R/C .

2)ADJUST THE V02 BUS DATA TO GET A WAVEFORM AS BELOW. 3) DISABLE THE Y-MUTE ** PLS TAKE NOTE THAT SERVICE MODE DATA F62 NEED TO SET 0.

ADJ US TMENT P ROCEDURE

B-AMP BASE (TP 47B)MUST BE IN STEPPING LEVEL

[CONFIRMATION ]

HIS TORY OF REVIS ION

S YMBOL

REVIS ED CONTENT .

5 – 18

0-127

21V1-L(A)

21V1-L(A)

MODEL NAME ADJ US TMENT ITEM

S UB-COLOR

ADJ US TMENT P OS ITION CONTROL

V03

S TEP RANGE

0-127

I2C BUS CONTROL

P RE-ADJ US T OP TION S ET UP , BUS S ET UP , VCO ADJ , RF-AGC, S UB-P ICT, S UB-TNT REQUIREMENT CONTENT

US 10 CH HALF COLOR BAR P ATTERN

INP UT CONDITION

220 V

OUTP UT

R-AMP TR BAS E (J A401) CONFIRM WITH OS CILLOS COP E 1)SET THE V03 BUS DATA TO GET A WAVEFORM AS BELOW 2)THIS WAVEFORM SHOWS THAT THE 75% WHITE & RED PORTIONS OF COLOR BAR BE AT THE SAME LEVEL

ADJ US TMENT P ROCEDURE

Cy

G

100% WHITE

W

Y

Mg

[CHECKING CONFIRMATION ]

HIS TORY OF REVIS ION

S YMBOL

REVIS ED CONTENT .

5 – 19

R

B

21V1-L(A)

21V1-L(A)

MODEL NAME ADJ US TMENT ITEM

X-RAY P ROTECTION OP ERATING CONFIRMATION

ADJ US TMENT P OS ITION CONTROL

S TEP RANGE

䋭

䋭

䋭

P RE-ADJ US T AFTER ALL ADJ US TMENT FINIS HED. REQUIREMENT CONTENT

US 4 CH LION HEAD (MONOS COP E P ATTERN)

INP UT CONDITION

AC 220V, RF INP UT

OUTP UT

CONFIRMATION BY THE CRT SET THE USER CONTROL TO SHIPMENT POSITION. [VOLTAGE CONFIRMATION] CHECK THE VOLTAGE OF C602 +VE TERMINAL AS SPECIFIED BELOW.

ADJ US TMENT P ROCEDURE

[OPERATION CONFIRMATION] SUPPLY THE DC VOLTAGE TO C602 +VE TERMINAL AND MAKE SURE THE PROTECTOR IS FUNCTIONED , HORIZONTAL OSCILATION STOP AND PICTURE DISAPPEAR. [RECOVER INFORMATION] PULL OUT THE AC CORD .

[CAUTION] FROM THE RECOVER CONFIRMATION MENTIONED ABOVE,THE AC CODE MUST BE PULLED OUT AT LEAST 4 SECOND BEFORE PLUGGING IN AGAIN. (IN ORDER TO MAKE SURE THE 㱘COM HAS BEEN RESET.)

[VOLTAGE COMFIRMATION]

㪤㪦㪛㪜㪣 21V1-L(A)

HISTORY OF REVISION

S YMBOL

TP VOLTAGE 26 ± 1.1V DC

REVIS ED CONTENT .

5 – 20

OPERATION VOLTAGE 27V

21V1-L(A)

21V1-L(A)

MODEL NAME ADJ USTMENT ITEM

HIGH VOLTAGE

ADJ USTMENT POSITION CONTROL

STEP RANGE

䋭

䋭

䋭

PRE-ADJ UST AFTER ALL ADJ USTMENT FINISHED. REQUIREMENT CONTENT

US 4 CH LION HEAD (MONOSCOPE PATTERN)

INPUT CONDITION

AC 220V, RF INPUT

OUTPUT

CRT ANODE VOLTAGE SET THE USER CONTROL TO SHIPMENT SETTING POSITION.PUSH ON Y - MUTE BY R/C CONFIRM THE VOLTAGE OF CRT ANODE BY HIGH VOLTAGE METER AND MAKE SURE THE READING IS AS BELOW.

ADJ US TMENT P ROCEDURE

MODEL 21V1-L(A)

HIGH VOLTAGE BELOW 27.5kV

[CAUTION POINT ] USE ELECTROSTATIC HI-VOLTAGE METER AND FOLLOW THE UL / DHHS STANDARD TO MAKE CORRECTION AND CONTROL. HIS TORY OF REVIS ION

S YMBOL

REVIS ED CONTENT .

5 – 21

21V1-L(A)

CHAPTER 6. WAVEFORMS Service Manual TV E Market 21V1-L(A)

WAVEFORMS (1) 1.004 Vp-p

(2) 4.71 Vp-p

(3) 4.38 Vp-p

(4) 4.42 Vp-p

(5) 5.390 Vp-p

Horiz. Rate

Horiz. Rate

Horiz. Rate

Horiz. Rate

Horiz. Rate

(6) 4.81 Vp-p

(7) 6.32 Vp-p

(8) 1.407 Vp-p

(9) 4.67 Vp-p

(10) 33.4 Vp-p

Vert. Rate

Horiz. Rate

Vert. Rate

Horiz. Rate

Horiz. Rate

(11) 1224 Vp-p

(12) 53.2 Vp-p

(13) 3.29 Vp-p

(14) 128.6 Vp-p

(15) 540Vp-p

Horiz. Rate

Vert.Rate

Vert. Rate

Horiz. Rate

-

(16) 119.3 Vp-p

(17) 101.4 Vp-p

(18) 104.8 Vp-p

Horiz. Rate

Horiz. Rate

Horiz. Rate

6â&#x20AC;&#x201C;1

21V1-L(A)

CHAPTER 7. CHASSIS LAYOUT Service Manual TV E Market 21V1-L(A)

+

*

)

(

'

&

%

$

7â&#x20AC;&#x201C;1

21V1-L(A)

CHAPTER 8. BLOCK DIAGRAM Service Manual TV E Market 21V1-L(A)

H

G

21V1-L (A) CRT BLOCK

F

E

D

C

B

A

1

2

3

4

6

5

8–1

7

8

9

10

21V1-L(A)

+

*

)

(

'

&

%

$

8â&#x20AC;&#x201C;2

21V1-L(A)

8â&#x20AC;&#x201C;3

21V1-L(A)

CHAPTER 9. DESCRIPTION OF SCHEMATIC DIAGRAM Service Manual TV E Market 21V1-L(A)

DESCRIPTION OF SCHEMATIC DIAGRAM NOTES: 1. The unit of resistance "ohm" is omitted.

(K=kΩ=1000Ω, M=MΩ) 2. All resistors are 1/16 watt, unless otherwise noted.

3. All capacitors are µF, unless otherwise noted.

(P=pF=µµF) 4. (G) indicates ±2% tolerance may be used.

5. indicates line isolated ground.

VOLTAGE MEASUREMENT CONDITIONS: 1. All DC voltages are measured with DVM connected between points indicated and chassis ground, line voltage set at 120V AC and all controls set for normal picture unless otherwise indicated.

2. All voltages measured with 1000µ V B & W or Color signal.

WAVEFORM MEASUREMENT CONDITIONS: 1. Photographs taken on a standard gated color bar

signal, the tint setting adjusted for proper color. The wave shapes at the red, green and blue cathodes of the picture tube depend on the tint, color level and picture control. indicates waveform check points (See chart, 2. waveforms are measured from point indicated to chassis ground.)

AND SHADED ( ) COMPONENTS = SAFETY RELATED PARTS. MARK= X-RAY RELATED PARTS. DRGANNES MARQUES ET HACHRES ( ): PIECES RELATIVES A LA SECURITE. MARQUE : PIECS RELATIVE AUX RAYONS X. This circuit diagram is a standard one, printed circuits may be subject to change for product improvement without prior notice.

9–1

21V1-L(A)

CHAPTER 10. SCHEMATIC DIAGRAM Service Manual TV E Market 21V1-L(A)

+

*

)

(

'

&

%

$

10 â&#x20AC;&#x201C; 1

21V1-L(A)

+

*

)

(

'

&

%

$

10 â&#x20AC;&#x201C; 2

21V1-L(A)

10 â&#x20AC;&#x201C; 3

21V1-L(A)

CHAPTER 11. PRINTED WIRING BOARD ASSEMBLIES Service Manual TV E Market 21V1-L(A)

+

*

)

(

'

&

%

07" ! -!). 5.)4 7IRING 3IDE

$

11 â&#x20AC;&#x201C; 1

21V1-L(A)

+

*

)

(

'

&

%

07" ! -!). 5.)4 #HIP 0ARTS 3IDE

$

11 â&#x20AC;&#x201C; 2

21V1-L(A)

+

*

)

(

'

&

%

07" " -!). 5.)4 7IRING 3IDE

$

11 â&#x20AC;&#x201C; 3

21V1-L(A)

+

*

)

(

'

&

%

07" " -!). 5.)4 #HIP 0ARTS 3IDE

$

11 â&#x20AC;&#x201C; 4

21V1-L(A)

PartsGuide

PARTS GUIDE No. S9811421V1L(A) XXXXXXXXXXXX

XXXXXXXX MODEL 21V1-L(A) CONTENTS [1]

PICTURE TUBE

[5]

MISCELLANEOUS PARTS

[2]

PRINTED WIRING BOARD ASSEMBLIES

[6]

SUPPLIED ACCESSORIES

[7]

CABINET PARTS

[3]

MAIN UNIT [8]

PACKING PARTS

Â&#x201E;

INDEX

[4]

CRT UNIT

Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.

This document has been published to be used for after sales service only.

The contents are subject to change without notice.

21V1-L(A) NO.

PARTS CODE

PRICE RANK

NEW MARK

PART DELIVERY

DESCRIPTION

[1] PICTURE TUBE VB540ADAC1S1E RCILGA164WJZZ QEARC2107PEZZ PMAGF3046CEZZ

! !

AG AF

R R R R

SEMI-ITC Picture Tube Degaussing Coil Ground-Part Magnet

-

MAIN Unit CRT Unit

R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R

Tuner AN17823A-1 LA78040B-1 PQ090RDA1SZ I.C. I.C. IM24C04W MM1501XN 2SC2735//1E 2SC3928AR 2SC2235 TT2140 2SC3198 2SC3928AR 2SD468 2SD468 2SD468 2SD468 2SC3928AR 2SA1530AR 2SC3928AR 2SA1530AR 2SC3928AR 2SC3928AR 2SC3928AR Zener Diode , 33V Diode Diode Diode , DX0302CE Zener Diode , 5.1V Diode , DX0441CE Diode , DX0131CE Diode , 1SS244 Zener Diode , 27V Diode , DX0131CE Diode , DX0476CE Diode , DX0066GE Diode , DX0066GE Diode , DX0066GE Zener Diode , 5.6V Diode , DX0066GE Zener Diode , 27V Zener Diode , 12.03V Zener Diode , 8.2V Zener Diode , 34.49V Diode , DXA044WJ Diode , DX0247CE Diode Zener Diode , 9.01V Diode Zener Diode Zener Diode Zener Diode Zener Diode Diode Photodiode Zener Diode , 10.71V Diode Zener Diode Zener Diode Diode Diode , DX0066GE Diode Diode Varistor Crystal Peaking 27mH Peaking 2.2mH Peaking 1.2mH Coil Coil Coil Peaking 10mH Peaking 10mH

[2] PRINTED WIRING BOARD ASSEMBLIES DUNTKE034WEB2 DUNTKE033WEB1

-

[3] MAIN UNIT ! ! !

!

TU201 IC301 IC501 IC601 IC701 IC801 IC1003 IC1401 Q201 Q351 Q601 Q602 Q603 Q604 Q751 Q752 Q753 Q754 Q801 Q802 Q803 Q805 Q1001 Q1002 Q1801 D201 D203 D204 D393 D503 D505 D510 D602 D603 D606 D701 D706 D707 D709 D715 D721 D722 D723 D732 D736 D751 D752 D801 D802 D803 D806 D807 D808 D809 D810 D1001 D1002 D1005 D1006 D1007 D1008 D1081 D1094 D1801 VA701 X801 L203 L205 L206 L602 L701 L751 L801 L802

RTUNQA037WJZZ VHIAN17821A-1 VHILA78040B-1 VHIPQ09RDA1-1 VHISTRW5453-1 RH-IXC031WJZZQ VHIM24C04W6-1Y VHIMM1501XN-1Y VS2SC2735//1EY VS2SC3928AR-1Y VS2SC2235Y/1E+ VSTT2140+++-F VS2SC3198-G-1+ VS2SC3928AR-1Y VS2SD468-C/-1+ VS2SD468-C/-1+ VS2SD468-C/-1+ VS2SD468-C/-1+ VS2SC3928AR-1Y VS2SA1530AR-1Y VS2SC3928AR-1Y VS2SA1530AR-1Y VS2SC3928AR-1Y VS2SC3928AR-1Y VS2SC3928AR-1Y VHEZJ33C+++1EY VHDHSS4148+-1Y VHDHSS4148+-1Y RH-DX0302CEZZ VHEZJ5R1B++1EY RH-DX0441CEZZY RH-DX0131CEZZY VHD1SS244//-1Y VHEZJ27B+++1EY RH-DX0131CEZZY RH-DX0476CEZZ RH-DX0066GEZZY RH-DX0066GEZZY RH-DX0066GEZZY VHEZJ5R6B++1EY RH-DX0066GEZZY VHEZJ27D+++1EY VHEZJ12B+++1EY VHEZJ8R2A++1EY VHEZJ36C+++1EY RH-DXA044WJZZ RH-DX0247CEZZ VHDHSS4148+-1Y VHEZJ9R1B++1EY VHDHSS4148+-1Y RH-EXA520WJZZY RH-EXA535WJZZY RH-EXA535WJZZY RH-EXA535WJZZY VHDHSS4148+-1Y RH-PX0013PEZZ VHEZJ11A+++1EY VHDHSS4148+-1Y RH-EXA520WJZZY RH-EXA520WJZZY VHDHSS4148+-1Y RH-DX0066GEZZY VHDHSS4148+-1Y VHDHSS4148+-1Y RH-VXA182WJZZ RCRSAA075WJZZ VP-DF270K0000Y VP-XF2R2K0000Y VP-XF1R2K0000Y RCILP0223CEZZ+ RCILFA187WJZZ RCILP0179CEZZ+ VP-DF100K0000Y VP-CF100K0000Y

AE AF AM AE AB AE AG AA AB AD AD AD AD AB AB AB AB AB AB AB AA AA AA AE AB AC AC AB AA AC AG AC AC AC AA AC AB AA AB AB AE AA AA AA AB AB AC AC AA AC AA AA AB AB AA AC AA AA AF AB AB AB AD AD AD AB AB

2

21V1-L(A) NO.

PARTS CODE

PRICE RANK

NEW MARK

DESCRIPTION

PART DELIVERY

[3] MAIN UNIT L803 L804 L807 L808 SF201 T602 T603 T701 C202 C203 C206 C207 C208 C209 C210 C213 C214 C301 C304 C305 C310 C313 C322 C383 C393 C451 C501 C505 C508 C511 C512 C513 C515 C601 C602 C604 C606 C607 C608 C610 C611 C642 C643 C650 C701 C702 C703 C704 C705 C706 C708 C709 C710 C711 C719 C750 C751 C752 C753 C754 C756 C757 C784 C801 C802 C803 C804 C805 C806 C807 C809 C810 C811 C814 C815 C816 C818 C819 C820 C821 C822 C823 C824 C825 C826

VP-CF220K0000Y VP-CF100K0000Y VP-DF100K0000Y VP-XF150K0000Y RFILCA055WJQZS RTRNFA137WJZZ RTRNZA058WJZZ RTRNWA216WJZZ VCEA0A1AW108M+ VCKYCY1HF103ZY VCEA0A1HW106M+ VCKYCY1HF103ZY VCKYCY1HF103ZY VCKYCY1HF103ZY VCKYCY1HF103ZY VCKYCY1HB102KY VCKYCY1HF103ZY VCEA0A1EW477M+ VCEA0A1HW475M+ VCEA9M1HW474M+ VCEA0A1HW104M+ VCKYCY1HB332KY VCEA0A1HW475M+ VCEA0A1CW106M+ VCEA0A1EW108M+ VCEA0A1CW477M+ VCFYFA1HA154J+ VCEA0A1HW107M+ VCFYAA2AA224J+ VCEA0A1VW477M+ VCKYPA2HB102K+ RC-EZA332WJZZ+ VCEACA1HC335J+ VCQYTA1HM563J+ VCEA0A1HW475M+ VCEA0A2EW336M+ VCKYPA2HB102K+ VCFPVC3ZA772H VCFYFA1HA563J+ VCEA0A1EW227M+ VCFPVC2EC474J VCEA0A1EW476M+ VCEA0A1CW477M+ VCKYPA2HB101K+ RC-FZ029SCEZZ RC-KZ0029CEZZ+ RC-KZ0029CEZZ+ RC-KZ0029CEZZ+ RC-EZA229WJZZ VCFYSA1HB105J+ VCKYPA1HB221K+ VCQYTA1HM103J+ VCQYTA1HM222J+ VCKYPA1HB222K+ VCEA0A1HW476M+ VCKYPA2HB102K+ RC-KZ0102GEZZ VCKYPH3DB561K RC-EZA235WJZZ RC-EZ0638CEZZ VCEA0A1EW228M+ VCCCCY1HH471JY VCKYPH3DB561K VCCCCY1HH330JY VCEA0A1AW107M+ VCKYCY1HB103KY VCEA0A1HW474M+ VCKYCY1HB153KY VCEA0A1CW476M+ VCKYCY1HB103KY VCEA0A1CW476M+ VCKYCY1HF103ZY VCFYFA1HA104J+ VCKYCY1CB563KY VCKYCY1HB103KY VCEA9M1HW474M+ VCEA0A1CW476M+ VCKYCY1HB103KY VCFYFA1HA104J+ VCEA0A1CW476M+ VCKYCY1HB104KY VCKYCY1HB104KY VCKYCY1CF105ZY VCEA0A1HW474M+ VCEA0A1HW335M+

AB AB AB AB AD AC AA AB AA AA AA AA AA AA AB AB AB AA AB AC AD AC AE AB AD AB AA AD AC AB AB AD AA AD AB AD AB AC AB AD AC AC AC AM AE AB AB AB AB AB AA AC AC AD AD AE AA AC AA AB AA AB AA AB AA AB AA AA AB AA AB AB AA AA AB AA AA AB AB AB

R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R

Peaking 22mH Peaking 10mH Peaking 10mH Peaking 15mH Coil H-Volt Transformer Transformer Transformer 1000 10V Electrolytic 0.01 50V Ceramic 10 50V Electrolytic 0.01 50V Ceramic 0.01 50V Ceramic 0.01 50V Ceramic 0.01 50V Ceramic 1 50V Ceramic 0.01 50V Ceramic 470 25V Electrolytic 4.7 50V Electrolytic 0.47 50V Electrolytic 0.1 50V Electrolytic 3.3 50V Ceramic 4.7 50V Electrolytic 10 16V Electrolytic 1000 25V Electrolytic 470 16V Electrolytic 0.15 50V Mylar 100 50V Electrolytic 0.22 100V Mylar 470 35V Electrolytic 1000p 500V Ceramic Capacitor 3.3 50V Electrolytic 0.56 50V Mylar 4.7 50V Electrolytic 33 250V Electrolytic 1000p 500V Ceramic 7.7 1.8KV Metalized Polypro Film 0.56 50V Mylar 220 25V Electrolytic 0.47 200V Metalized Polypro Film 47 25V Electrolytic 470 16V Electrolytic 100p 500V Ceramic 220 275V Metalized Plastic Film 0.01 250V Ceramic 0.01 250V Ceramic 0.01 250V Ceramic 220 400V Electrolytic 1 50V Mylar 220p 50V Ceramic 0.01 50V Mylar 2.2 50V Mylar 2200p 50V Ceramic 47 50V Electrolytic 1000p 500V Ceramic 2kV Ceramic 560p 2KV Ceramic 160V Electrolytic 33 160V Electrolytic 2200 25V Electrolytic 470p 50V Ceramic 560p 2KV Ceramic 33p 50V Ceramic 100 10V Electrolytic 0.01 50V Ceramic 0.47 50V Electrolytic 0.15 50V Ceramic 47 16V Electrolytic 0.01 50V Ceramic 47 16V Electrolytic 0.01 50V Ceramic 0.1 50V Mylar 0.56 16V Ceramic 0.01 50V Ceramic 0.47 50V Electrolytic 47 16V Electrolytic 0.01 50V Ceramic 0.1 50V Mylar 47 16V Electrolytic 0.1 50V Ceramic 0.1 50V Ceramic 1 16V Ceramic 0.47 50V Electrolytic 3.3 50V Electrolytic

3

21V1-L(A) NO.

PARTS CODE

PRICE RANK

NEW MARK

PART DELIVERY

DESCRIPTION

[3] MAIN UNIT C827 C828 C829 C830 C831 C832 C833 C834 C836 C837 C838 C839 C840 C841 C842 C843 C847 C849 C1001 C1002 C1003 C1004 C1006 C1012 C1013 C1016 C1017 C1018 C1019 C1020 C1021 C1022 C1081 C1401 C1402 C1403 C1404 C1840 C1841 C1842 C1843 C1846 C1847 C1849 C1852 C1853 C1858 C1860 C1868 RJ2 RJ5 RJ8 RJ16 RJ17 RJ19 RJ20 RJ24 R201 R202 R204 R205 R206 R207 R208 R209 R216 R220 R301 R302 R303 R304 R305 R314 R315 R316 R353 R366 R372 R373 R376 R458 R459 R461 R462 R503

VCEA0A1CW106M+ VCEA9M1HW474M+ VCKYCY1CF105ZY VCKYCY1HB103KY VCEA0A1AW477M+ VCFYFA1HA104J+ VCEA0A1HW104M+ VCKYCY1CF104ZY VCKYCY1HB332KY VCKYCY1HB104KY VCEA0A1CW477M+ VCKYCY1HF103ZY VCKYCY1CF105ZY VCKYCY1HB103KY VCKYCY1HB104KY VCEA0A1HW475M+ VCKYPA1HB471K+ VCKYCY1CF105ZY VCEA0A1AW107M+ VCCCCY1HH101JY VCEA0A1CW106M+ VCKYCY1CF474ZY VCEA0A1HW225M+ VRS-CY1JF000JY VCKYCY1HB103KY VCKYCY1EF104ZY VCKYCY1HB221KY VCEA0A1HW105M+ VCKYCY1HB102KY VCKYCY1HB561KY VCKYCY1EF104ZY VCEA0A0JW477M+ VCFYFA1HA104J+ VCEA0A1CW107M+ VCKYCY1HF103ZY VCEA0A1CW106M+ VCEA0A1CW106M+ VCEA0A1CW226M+ VCEA0A1CW477M+ VCKYCY1HB103KY VCKYCY1HB104KY VRS-CY1JF000JY VRS-CY1JF000JY VRS-CY1JF000JY VCKYCY1HB103KY VCEA0A1CW476M+ VCCCCY1HH220JY VCCCCY1HH220JY VCEA0A1CW336M+ VRS-CY1JF000JY VRS-CY1JF000JY VRS-CY1JF000JY VRS-CY1JF000JY VRS-CY1JF000JY VRS-CY1JF000JY VRS-CY1JF000JY VRS-CY1JF000JY VRS-CY1JF101JY VRS-CY1JF101JY VRS-CY1JF332JY VRS-CY1JF680JY VRS-CY1JF122JY VRS-CY1JF221JY VRS-CY1JF331JY VRS-CY1JF392JY VRS-RG3LB393J+ VRS-CY1JF221JY VRD-RA2BE102JY VRN-KT3LB1R8J VRS-CY1JF473JY VRD-RA2BE683JY VRS-CY1JF274JY VRD-RA2BE392JY VRS-CY1JF272JY VRS-CY1JF103JY VRS-CY1JF102JY VRS-CY1JF332JY VRS-CY1JF104JY VRS-CY1JF103JY VRD-RA2BE472JY VRS-CY1JF103JY VRD-RA2EE750JY VRS-CY1JF750JY VRD-RA2BE101JY VRN-RL3DB1R2J+

AB AB AB AA AC AA AB AB AA AA AC AA AB AA AA AB AA AB AB AA AB AB AB AA AA AA AA AB AA AA AA AC AA AC AA AC AC AC AC AA AA AA AA AA AA AB AA AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AC AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB

R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R

10 16V Electrolytic 0.47 50V Electrolytic 1 16V Ceramic 0.01 50V Ceramic 470 10V Electrolytic 0.1 50V Mylar 0.1 50V Electrolytic 0.1 16V Ceramic 3.3 50V Ceramic 0.1 50V Ceramic 470 16V Electrolytic 0.01 50V Ceramic 1 16V Ceramic 0.01 50V Ceramic 0.1 50V Ceramic 4.7 50V Electrolytic 470p 50V Ceramic 1 16V Ceramic 100 10V Electrolytic 100p 50V Ceramic 10 16V Electrolytic 0.47 16V Ceramic 2.2 50V Electrolytic 0 1/16W Metal Oxide 0.01 50V Ceramic 0.1 25V Ceramic 220 50V Ceramic 1 50V Electrolytic 1 50V Ceramic 560 50V Ceramic 0.1 25V Ceramic 470 6.3V Electrolytic 0.1 50V Mylar 100 16V Electrolytic 0.01 50V Ceramic 10 16V Electrolytic 10 16V Electrolytic 22 16V Electrolytic 470 16V Electrolytic 0.01 50V Ceramic 0.1 50V Ceramic 0 1/16W Metal Oxide 0 1/16W Metal Oxide 0 1/16W Metal Oxide 0.01 50V Ceramic 47 16V Electrolytic 22p 50V Ceramic 22p 50V Ceramic 33 16V Electrolytic 0 1/16W Metal Oxide 0 1/16W Metal Oxide 0 1/16W Metal Oxide 0 1/16W Metal Oxide 0 1/16W Metal Oxide 0 1/16W Metal Oxide 0 1/16W Metal Oxide 0 1/16W Metal Oxide 100 1/16W Metal Oxide 100 1/16W Metal Oxide 3.3K 1/16W Metal Oxide 68 1/16W Metal Oxide 1.2K 1/16W Metal Oxide 220 1/16W Metal Oxide 330 1/16W Metal Oxide 3.9K 1/16W Metal Oxide 39K 3W Metal Film 220 1/16W Metal Oxide 1K 1/8W Carbon 1.8 3W Metal Oxide 47K 1/16W Metal Oxide 68K 1/8W Carbon 270K 1/16W Metal Oxide 3.9K 1/8W Carbon 2.7K 1/16W Metal Oxide 10K 1/16W Metal Oxide 1K 1/16W Metal Oxide 3.3K 1/16W Metal Oxide 100K 1/16W Metal Oxide 10K 1/16W Metal Oxide 4.7K 1/8W Carbon 10K 1/16W Metal Oxide 75 250V Carbon 75 1/16W Metal Oxide 100 1/8W Carbon 1.2 2W Metal Film

4

21V1-L(A) NO.

PARTS CODE

PRICE RANK

NEW MARK

DESCRIPTION

PART DELIVERY

[3] MAIN UNIT R504 R506 R507 R513 R514 R520 R523 R524 R528 R601 R602 R603 R604 R605 R606 R607 R608 R609 R611 R612 R614 R615 R616 R617 R618 R621 R622 R631 R637 R638 R639 R642 R661 R662 R702 R704 R705 R706 R710 R720 R722 R726 R733 R751 R752 R753 R754 R755 R801 R802 R803 R804 R805 R806 R807 R808 R809 R810 R811 R812 R813 R814 R815 R816 R817 R818 R819 R821 R822 R823 R824 R825 R826 R827 R828 R829 R831 R832 R833 R834 R835 R837 R838 R840 R841

VRS-CY1JF222JY VRS-RG3AB331J+ VRD-RM2HD1R0JY VRD-RM2HD333JY VRD-RM2HD393JY VRS-CY1JF123JY VRD-RA2BE103JY VRD-RA2BE103JY VRD-RM2HD103JY VRD-RM2HD680JY VRD-RA2BE393JY VRD-RA2BE223JY VRD-RA2BE473JY VRD-RM2HD104JY VRN-RL3LBR18J+ VRD-RM2HD680JY VRD-RM2HD102JY VRD-RM2HD270JY VRN-RL3AB1R2J+ VRD-RM2HD270JY VRD-RA2BE154JY VRD-RA2BE102JY VRD-RA2BE102JY VRS-CY1JF123JY VRS-CY1JF103JY VRN-RL2HC100J+ VRS-VV3DB682J VRS-RG3LB391J+ VRD-RA2BE331JY VRD-RA2BE181JY VRD-RM2HD151JY VRN-RL3DB1R0J+ VRD-RA2BE102JY VRD-RA2BE103JY VRS-VV3DB124J VRD-RA2BE221JY VRN-RL3DBR82J+ VRN-RL3DBR22J+ VRD-RM2HD1R0JY VRD-RA2EE472JY VRD-RA2BE153JY VRN-RL2HCR47J+ VRD-RA2BE273JY RR-DZ0049CEZZY RR-DZ0049CEZZY VRD-RM2HD124JY VRN-RL3AB8R2J+ VRS-RG3DB121J+ VRS-CY1JF102JY VRS-CY1JF473JY VRD-RA2BE101JY VRS-CY1JF101JY VRD-RA2BE101JY VRS-CY1JF822JY VRS-CY1JF124JY VRS-CY1JF101JY QJUM-0001AJFWY VRS-CY1JF103JY VRS-CY1JF103JY VRS-CY1JF822JY VRD-RM2HD151JY VRS-CY1JF101JY VRS-CY1JF101JY VRS-CY1JF471JY VRS-CY1JF331JY VRS-CY1JF220JY VRS-CY1JF102JY VRD-RA2BE101JY VRS-CY1JF182JY VRS-CY1JF472JY VRS-CY1JF181JY VRS-CY1JF473JY VRS-CY1JF181JY VRS-CY1JF181JY VRS-CY1JF223JY VRS-CY1JF473JY VRD-RA2BE122JY VRS-CY1JF182JY VRS-CY1JF182JY VRS-CY1JF182JY VRS-CY1JF103JY VCKYCY1HB104KY VRS-CY1JF472JY VRS-CY1JF101JY VRS-CY1JF470JY

AA AB AA AA AA AA AA AA AA AA AA AA AA AA AD AA AA AA AB AA AA AA AA AA AA AB AA AA AA AA AB AA AA AA AA AB AB AA AA AA AB AA AA AB AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA

R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R

2.2K 1/16W Metal Oxide 330 1W Metal Oxide 1 1/2W Carbon 33K 1/2W Carbon 33K 1/2W Carbon 12K 1/16W Metal Oxide 10K 1/8W Carbon 10K 1/8W Carbon 10K 1/2W Carbon 68 1/2W Carbon 39K 1/8W Carbon 22K 1/8W Carbon 47K 1/8W Carbon 100K 1/2W Carbon 18 3W Metal Film 68 1/2W Carbon 1K 1/2W Carbon 27 1/2W Carbon 1.2 1W Metal Film 27 1/2W Carbon 150K 1/8W Carbon 1K 1/8W Carbon 1K 1/8W Carbon 12K 1/16W Metal Oxide 10K 1/16W Metal Oxide 10 1/2W Metal Oxide 6.8K 2W Metal Oxide 390 3W Metal Oxide 330 1/8W Carbon 180 1/8W Carbon 150 1/2W Carbon 1 2W Metal Film 1K 1/8W Carbon 10K 1/8W Carbon 120K 2W Metal Oxide 220 1/8W Carbon 82 2W Metal Film 22 2W Metal Film 1 1/2W Carbon 4.7K 1/4W Carbon 15K 1/8W Carbon 0.47 1/2W Metal Oxide 27K 1/8W Carbon 39M 1/2W Carbon Film 39M 1/2W Carbon Film 120K 1/2W Carbon 8.2 1W Metal Film 120 2W Metal Film 1K 1/16W Metal Oxide 47K 1/16W Metal Oxide 100 1/8W Carbon 100 1/16W Metal Oxide 100 1/8W Carbon 8.2K 1/16W Metal Oxide 120K 1/16W Metal Oxide 100 1/16W Metal Oxide Jumper wire 10K 1/16W Metal Oxide 10K 1/16W Metal Oxide 8.2K 1/16W Metal Oxide 150 1/2W Carbon 100 1/16W Metal Oxide 100 1/16W Metal Oxide 470 1/16W Metal Oxide 330 1/16W Metal Oxide 22 1/16W Metal Oxide 1K 1/16W Metal Oxide 100 1/8W Carbon 1.8K 1/16W Metal Oxide 4.7K 1/16W Metal Oxide 180 1/16W Metal Oxide 47K 1/16W Metal Oxide 180 1/16W Metal Oxide 180 1/16W Metal Oxide 22K 1/16W Metal Oxide 47K 1/16W Metal Oxide 1.2K 1/8W Carbon 1.8K 1/16W Metal Oxide 1.8K 1/16W Metal Oxide 1.8K 1/16W Metal Oxide 10K 1/16W Metal Oxide 0.1 50V Ceramic 4.7K 1/16W Metal Oxide 100 1/16W Metal Oxide 47 1/16W Metal Oxide

5

21V1-L(A) NO.

PARTS CODE

PRICE RANK

NEW MARK

PART DELIVERY

DESCRIPTION

[3] MAIN UNIT

!

R843 R862 R1003 R1004 R1008 R1010 R1011 R1012 R1013 R1014 R1015 R1016 R1017 R1018 R1019 R1020 R1021 R1022 R1024 R1025 R1026 R1027 R1028 R1030 R1031 R1032 R1038 R1039 R1040 R1041 R1042 R1044 R1045 R1046 R1056 R1074 R1087 R1092 R1383 R1384 R1401 R1402 R1403 R1431 R1432 R1801 R1802 R1803 R1894 R1895 R1896 S701 S1001 S1002 S1003 S1004 S1005 F701 FH701 FH702 J405 J1402 J1403 P301 P601 P602 P701 P702 P1001 P1002 RMC1001 RDA501 RDA601 RDA602 RDA701 TP801

VRS-CY1JF222JY VRD-RA2BE101JY VRS-CY1JF102JY VRD-RA2BE101JY VRD-RA2BE101JY VRS-CY1JF104JY VRS-CY1JF183JY VRD-RA2BE183JY VRD-RA2BE101JY VRS-CY1JF101JY VRD-RA2BE101JY VRD-RA2BE332JY VRD-RA2BE101JY VRS-CY1JF103JY VRD-RA2BE101JY VRS-CY1JF183JY VRS-CY1JF822JY VRS-CY1JF183JY VRS-CY1JF101JY VRD-RA2BE103JY VRS-CY1JF183JY VRS-CY1JF104JY VRD-RA2BE391JY VRS-CY1JF103JY VRS-CY1JF101JY VRS-CY1JF332JY VRS-CY1JF562JY VRS-CY1JF102JY VRS-CY1JF101JY VRS-CY1JF105JY VRS-CY1JF471JY VRS-CY1JF473JY VRS-CY1JF104JY VRS-CY1JF472JY VRS-CY1JF332JY VRS-CY1JF332JY VRS-CY1JF000JY VRS-CY1JF472JY VRS-CY1JF103JY VRS-CY1JF332JY VRS-CY1JF101JY VRD-RA2BE101JY VRS-CY1JF101JY VRS-CY1JF101JY VRS-CY1JF750JY VRS-CY1JF222JY VRS-CY1JF124JY VRS-CY1JF475JY VRS-CY1JF103JY VRS-CY1JF473JY VRS-CY1JF473JY QSW-PA003WJZZ QSW-KA019WJZZ+ QSW-KA019WJZZ+ QSW-KA019WJZZ+ QSW-KA019WJZZ+ QSW-KA019WJZZ+ QFS-C3225CEZZ QFSHD1013CEZZ+ QFSHD1014CEZZ+ QJAKH0044AJZZ QJAKEA056WJ04 QJAKEA056WJ09 QPLGNA107WJZZ QPLGN0660CEZZ LHLDW1104PEZZ QPLGN0260CEZZ QPLGN0269GEZZ LHLDW1105PEZZ QPLGNA110WJZZ RRMCUA022WJZZ PRDARA120WJFW PRDARA167WJFW PRDARA361WJFW PRDARA119WJFW QLUGP0111GEFW

AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AG AC AC AC AC AC AC AC AC

AB AC AB AC AB AB AB AG AD AD AF AA

R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R

2.2K 1/16W Metal Oxide 100 1/8W Carbon 1K 1/16W Metal Oxide 100 1/8W Carbon 100 1/8W Carbon 100K 1/16W Metal Oxide 18K 1/16W Metal Oxide 18K 1/8W Carbon 100 1/8W Carbon 100 1/16W Metal Oxide 100 1/8W Carbon 3.3K 1/8W Carbon 100 1/8W Carbon 10K 1/16W Metal Oxide 100 1/8W Carbon 18K 1/16W Metal Oxide 8.2K 1/16W Metal Oxide 18K 1/16W Metal Oxide 100 1/16W Metal Oxide 10K 1/8W Carbon 18K 1/16W Metal Oxide 100K 1/16W Metal Oxide 390 1/8W Carbon 10K 1/16W Metal Oxide 100 1/16W Metal Oxide 3.3K 1/16W Metal Oxide 5.6K 1/16W Metal Oxide 1K 1/16W Metal Oxide 100 1/16W Metal Oxide 1M 1/16W Metal Oxide 470 1/16W Metal Oxide 47K 1/16W Metal Oxide 100K 1/16W Metal Oxide 4.7K 1/16W Metal Oxide 3.3K 1/16W Metal Oxide 3.3K 1/16W Metal Oxide 0 1/16W Metal Oxide 4.7K 1/16W Metal Oxide 10K 1/16W Metal Oxide 3.3K 1/16W Metal Oxide 100 1/16W Metal Oxide 100 1/8W Carbon 100 1/16W Metal Oxide 100 1/16W Metal Oxide 75 1/16W Metal Oxide 2.2K 1/16W Metal Oxide 120K 1/16W Metal Oxide 4.7M 1/16W Metal Oxide 10K 1/16W Metal Oxide 47K 1/16W Metal Oxide 47K 1/16W Metal Oxide Switch , POWER Switch , CH UP Switch , CH DOWN Switch , VOL UP Switch , VOL DOWN Switch , MENU Fuse , 3.15A 250V Fuse Holder Fuse Holder Jack Jack Jack Plug ,4Pin(S) Plug ,6Pin(F) Plug Plug ,2Pin(M) Plug ,2Pin Plug Plug ,5Pin(BC) Remote Receiver Heat Sink for IC501 Heat Sink for IC601 Heat Sink for Q602 Heat Sink for IC701 Lug

6

21V1-L(A) NO.

PARTS CODE

PRICE RANK

NEW MARK

DESCRIPTION

PART DELIVERY

[4] CRT UNIT

! ! !

Q853 Q854 Q855 Q894 D859 D896 D898 L851 C851 C852 C853 C880 C893 R849 R850 R851 R852 R854 R855 R859 R861 R863 R864 R876 R877 R878 R880 R881 R882 R891 R892 R894 R895 P860 P880 SC851

RH-TX0110BMZZ+ RH-TX0110BMZZ+ RH-TX0110BMZZ+ VS2SA1530AR-1Y VHDHSS4148+-1Y VHEZJ5R6C++1EY VHDHSS4148+-1Y VP-MK820K0000+ VCKYPA1HB561K+ VCKYPA1HB331K+ VCKYPA1HB391K+ RC-KZ0016CEZZ VCEA0A1CW336M+ VRS-CY1JF271JY VRS-CY1JF470JY VRS-CY1JF470JY VRS-CY1JF470JY VRS-CY1JF271JY VRS-CY1JF271JY VRS-VV3DB153J VRS-VV3DB153J VRS-VV3DB153J VRD-RA2BE470JY VRS-CY1JF121JY VRS-CY1JF121JY VRS-CY1JF121JY VRD-RM2HD332JY VRD-RM2HD332JY VRD-RM2HD332JY VRS-CY1JF152JY VRS-CY1JF391JY VRS-CY1JF152JY VRD-RA2BE561JY LHLDW1104PEZZ LHLDW1105PEZZ QSOCVA023WJZZ

AC AC AC AB AA AA AA AB AA AB AA AC AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AB AE

R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R

TX0110 TX0110 TX0110 2SA1530AR Diode Zener Diode , 5.6V Diode Peaking 82mH 560p 50V Ceramic 330p 50V Ceramic 390p 50V Ceramic 10000p 1.5KV Ceramic 33 16V Electrolytic 270 1/16W Metal Oxide 47 1/16W Metal Oxide 47 1/16W Metal Oxide 47 1/16W Metal Oxide 270 1/16W Metal Oxide 270 1/16W Metal Oxide 15K 12W Metal Oxide 15K 12W Metal Oxide 15K 12W Metal Oxide 47 1/8W Carbon 120 1/16W Metal Oxide 120 1/16W Metal Oxide 120 1/16W Metal Oxide 3.3K 1/2W Carbon 3.3K 1/2W Carbon 3.3K 1/2W Carbon 1.5K 1/16W Metal Oxide 390 1/16W Metal Oxide 1.5K 1/16W Metal Oxide 560 1/8W Carbon Plug 4Pin (H) Plug 5Pin (K) Socket , 12Pin

R R R R R

AC Cord SPEAKER 16 OHM SP WIRE (+--+) H-WIRE K-WIRE

R R R

Infrared Remote Control Unit Operation Manual Battery

[5] MISCELLANEOUS PARTS !

ACC701 SP301

QACCZA091WJPZ VSP9050PA02WA QCNW-2378PEZZ QCNW-A230WJZZ QCNW-A720WJZZ

AH AD AD

[6] SUPPLIED ACCESSORIES RRMCGA257WJSB TINS-D625WJZZ UBATUA004WJZZ

7

21V1-L(A)

[7] CABINET PARTS 1-1

21V1-L(A)

1

1-6

1-2

1-3

1-4

1-5

2

2-1

2-2

NO.

PARTS CODE

PRICE RANK

NEW MARK

DESCRIPTION

PART DELIVERY

[7] CABINET PARTS 1 1-1 1-2 1-3 1-4 1-5 1-6 2 2-1

CCABAC054WEV0 Not Available JBTN-A751WJSA MSPRC0005PEFW GCOVAC834WJSA JBTN-A752WJSA HBDGBA085WJSA CCABBB309WEV0 Not Available

-

R R R

-

R R R -

Front Cabinet Ass'y Front Cabinet Power Button Power Button Spring R/C & LED Cover Control Button Sharp Badge Rear Cabinet Ass'y Rear Cabinet

8

21V1-L(A)

[8] PACKING PARTS 3$&.,1* 2) 7+( 6+((7

66$.$ 3(== 3RO\HWK\OHQH %DJ

2SHUDWLRQ 0DQXDO %DWWHULHV

,QIUD 5HG 5 & 8QLW

63$.3 3(== :UDSSLQJ 6DFN

63$.;& :-==

%XIIHU 0DWHULDO

63$.&( :-==

3DFNLQJ &DVH

86( 3$&.,1* 7$3(6 ),; 7+( 3$&.,1* &$6( 0$5. 1RW UHSODFHPHQW LWHPV

NO.

PARTS CODE

PRICE RANK

NEW MARK

DESCRIPTION

PART DELIVERY

[8] PACKING PARTS 3 4 5 6

SPAKCE191WJZZ SPAKP0099PEZZ SPAKXC028WJZZ SSAKA0001PEZZ

-

-

Packing Case Wraping Sack Buffer Material Polyethylene Bag

9

21V1-L(A)

INDEX PARTS CODE

No.

PRICE NEW PART RANK MARK RANK

[C] CCABAC054WEV0 CCABBB309WEV0

7-1 7-2

-

R R

22-

-

-

7-1-6

-

R

7-1-2 7-1-5

-

R R

AB AB AB AB

R R R R

7-1-3

-

R

7-1-1 7-2-1

-

-

AF AF AD AD

R R R R R

[D] DUNTKE033WEB1 DUNTKE034WEB2 [G] GCOVAC834WJSA [H] HBDGBA085WJSA [J] JBTN-A751WJSA JBTN-A752WJSA [L] LHLDW1104PEZZ " LHLDW1105PEZZ " [M] MSPRC0005PEFW [N] Not Available " [P] PMAGF3046CEZZ PRDARA119WJFW PRDARA120WJFW PRDARA167WJFW PRDARA361WJFW [Q] QACCZA091WJPZ QCNW-2378PEZZ QCNW-A230WJZZ QCNW-A720WJZZ QEARC2107PEZZ QFS-C3225CEZZ QFSHD1013CEZZ+ QFSHD1014CEZZ+ QJAKEA056WJ04 QJAKEA056WJ09 QJAKH0044AJZZ QJUM-0001AJFWY QLUGP0111GEFW QPLGN0260CEZZ QPLGN0269GEZZ QPLGN0660CEZZ QPLGNA107WJZZ QPLGNA110WJZZ QSOCVA023WJZZ QSW-KA019WJZZ+ " " " " QSW-PA003WJZZ [R] RC-EZ0638CEZZ RC-EZA229WJZZ RC-EZA235WJZZ RC-EZA332WJZZ+ RC-FZ029SCEZZ RCILFA187WJZZ RCILGA164WJZZ RCILP0179CEZZ+ RCILP0223CEZZ+ RC-KZ0016CEZZ RC-KZ0029CEZZ+ " " RC-KZ0102GEZZ RCRSAA075WJZZ RFILCA055WJQZS RH-DX0066GEZZY " " " " RH-DX0131CEZZY " RH-DX0247CEZZ

7-1-4

3-P602 4-P860 3-P1001 4-P880

13-RDA701 3-RDA501 3-RDA601 3-RDA602 5-ACC701 55513-F701 3-FH701 3-FH702 3-J1402 3-J1403 3-J405 3-R809 3-TP801 3-P701 3-P702 3-P601 3-P301 3-P1002 4-SC851 3-S1001 3-S1002 3-S1003 3-S1004 3-S1005 3-S701 3-C754 3-C705 3-C753 3-C513 3-C701 3-L701 13-L751 3-L602 4-C880 3-C702 3-C703 3-C704 3-C751 3-X801 3-SF201 3-D706 3-D707 3-D709 3-D721 3-D1081 3-D510 3-D606 3-D752

AD AD AG AC AC AC

AA AC AB AC AB AB AE AC AC AC AC AC AG AD AM AD AD AD AD AD AD AC AC AC AC AC AF AC AC AC AC AC AC AC AE

R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R

10

21V1-L(A) PARTS CODE RH-DX0302CEZZ RH-DX0441CEZZY RH-DX0476CEZZ RH-DXA044WJZZ RH-EXA520WJZZY " " RH-EXA535WJZZY " " RH-IXC031WJZZQ RH-PX0013PEZZ RH-TX0110BMZZ+ " " RH-VXA182WJZZ RR-DZ0049CEZZY " RRMCGA257WJSB RRMCUA022WJZZ RTRNFA137WJZZ RTRNWA216WJZZ RTRNZA058WJZZ RTUNQA037WJZZ [S] SPAKCE191WJZZ SPAKP0099PEZZ SPAKXC028WJZZ SSAKA0001PEZZ

No. 3-D393 3-D505 3-D701 3-D751 3-D806 3-D1006 3-D1007 3-D807 3-D808 3-D809 3-IC801 3-D1001 4-Q853 4-Q854 4-Q855 3-VA701 3-R751 3-R752 63-RMC1001 3-T602 3-T701 3-T603 3-TU201 8-3 8-4 8-5 8-6

PRICE NEW PART RANK MARK RANK AE AC AG AB AB AB AB AC AC AC AC AC AC

AG

AD

-

R R R R R R R R R R R R R R R R R R R R R R R R -

[T] TINS-D625WJZZ

6-

R

6-

R

[U] UBATUA004WJZZ [V] VB540ADAC1S1E VCCCCY1HH101JY VCCCCY1HH220JY " VCCCCY1HH330JY VCCCCY1HH471JY VCEA0A0JW477M+ VCEA0A1AW107M+ " VCEA0A1AW108M+ VCEA0A1AW477M+ VCEA0A1CW106M+ " " " " VCEA0A1CW107M+ VCEA0A1CW226M+ VCEA0A1CW336M+ " VCEA0A1CW476M+ " " " " VCEA0A1CW477M+ " " " VCEA0A1EW108M+ VCEA0A1EW227M+ VCEA0A1EW228M+ VCEA0A1EW476M+ VCEA0A1EW477M+ VCEA0A1HW104M+ " VCEA0A1HW105M+ VCEA0A1HW106M+ VCEA0A1HW107M+ VCEA0A1HW225M+ VCEA0A1HW335M+ VCEA0A1HW474M+ " VCEA0A1HW475M+ " " " VCEA0A1HW476M+

13-C1002 3-C1858 3-C1860 3-C801 3-C757 3-C1022 3-C802 3-C1001 3-C202 3-C831 3-C383 3-C827 3-C1003 3-C1403 3-C1404 3-C1401 3-C1840 3-C1868 4-C893 3-C806 3-C809 3-C818 3-C821 3-C1853 3-C451 3-C643 3-C838 3-C1841 3-C393 3-C610 3-C756 3-C642 3-C301 3-C310 3-C833 3-C1018 3-C206 3-C505 3-C1006 3-C826 3-C804 3-C825 3-C304 3-C322 3-C602 3-C843 3-C719

AA AA AA AA AA AC AB AB AC AC AC AB AB AC AC AC AC AB AB AB AB AB AB AB AC AC AC AC AD AB AE AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB

R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R

11

21V1-L(A) PARTS CODE

No.

PRICE NEW PART RANK MARK RANK

PARTS CODE

No.

PRICE NEW PART RANK MARK RANK

VCEA0A2EW336M+ VCEA9M1HW474M+ " " VCEACA1HC335J+ VCFPVC2EC474J VCFPVC3ZA772H VCFYAA2AA224J+ VCFYFA1HA104J+ " " " VCFYFA1HA154J+ VCFYFA1HA563J+ VCFYSA1HB105J+ VCKYCY1CB563KY VCKYCY1CF104ZY VCKYCY1CF105ZY " " " VCKYCY1CF474ZY VCKYCY1EF104ZY " VCKYCY1HB102KY " VCKYCY1HB103KY " " " " " " " " VCKYCY1HB104KY " " " " " VCKYCY1HB153KY VCKYCY1HB221KY VCKYCY1HB332KY " VCKYCY1HB561KY VCKYCY1HF103ZY " " " " " " " " VCKYPA1HB221K+ VCKYPA1HB222K+ VCKYPA1HB331K+ VCKYPA1HB391K+ VCKYPA1HB471K+ VCKYPA1HB561K+ VCKYPA2HB101K+ VCKYPA2HB102K+ " " VCKYPH3DB561K " VCQYTA1HM103J+ VCQYTA1HM222J+ VCQYTA1HM563J+ VHD1SS244//-1Y VHDHSS4148+-1Y " " " " " " " "

3-C604 3-C305 3-C816 3-C828 3-C515 3-C611 3-C607 3-C508 3-C811 3-C820 3-C832 3-C1081 3-C501 3-C608 3-C706 3-C814 3-C834 3-C824 3-C829 3-C840 3-C849 3-C1004 3-C1016 3-C1021 3-C213 3-C1019 3-C803 3-C807 3-C815 3-C819 3-C830 3-C841 3-C1013 3-C1842 3-C1852 3-C822 3-C823 3-C837 3-C842 3-R837 3-C1843 3-C805 3-C1017 3-C313 3-C836 3-C1020 3-C203 3-C207 3-C208 3-C209 3-C210 3-C214 3-C810 3-C839 3-C1402 3-C708 3-C711 4-C852 4-C853 3-C847 4-C851 3-C650 3-C512 3-C606 3-C750 3-C752 3-C784 3-C709 3-C710 3-C601 3-D602 3-D203 3-D204 3-D801 3-D803 3-D810 3-D1005 3-D1008 3-D1094 3-D1801

AD AB AB AC AD AD AD AA AA AA AA AE AE AB AB AB AB AB AB AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AB AB AA AA AA AB AA AA AA AC AC AB AB AB AB AA AA AA AA AA AA AA AA AA

PARTS CODE

R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R

" " VHEZJ11A+++1EY VHEZJ12B+++1EY VHEZJ27B+++1EY VHEZJ27D+++1EY VHEZJ33C+++1EY VHEZJ36C+++1EY VHEZJ5R1B++1EY VHEZJ5R6B++1EY VHEZJ5R6C++1EY VHEZJ8R2A++1EY VHEZJ9R1B++1EY VHIAN17821A-1 VHILA78040B-1 VHIM24C04W6-1Y VHIMM1501XN-1Y VHIPQ09RDA1-1 VHISTRW5453-1 VP-CF100K0000Y " VP-CF220K0000Y VP-DF100K0000Y " VP-DF270K0000Y VP-MK820K0000+ VP-XF150K0000Y VP-XF1R2K0000Y VP-XF2R2K0000Y VRD-RA2BE101JY " " " " " " " " " " " VRD-RA2BE102JY " " " VRD-RA2BE103JY " " " VRD-RA2BE122JY VRD-RA2BE153JY VRD-RA2BE154JY VRD-RA2BE181JY VRD-RA2BE183JY VRD-RA2BE221JY VRD-RA2BE223JY VRD-RA2BE273JY VRD-RA2BE331JY VRD-RA2BE332JY VRD-RA2BE391JY VRD-RA2BE392JY VRD-RA2BE393JY VRD-RA2BE470JY VRD-RA2BE472JY VRD-RA2BE473JY VRD-RA2BE561JY VRD-RA2BE683JY VRD-RA2EE472JY VRD-RA2EE750JY VRD-RM2HD102JY VRD-RM2HD103JY VRD-RM2HD104JY VRD-RM2HD124JY VRD-RM2HD151JY " VRD-RM2HD1R0JY " VRD-RM2HD270JY " VRD-RM2HD332JY

12

No. 4-D859 4-D898 3-D1002 3-D723 3-D603 3-D722 3-D201 3-D736 3-D503 3-D715 4-D896 3-D732 3-D802 3-IC301 3-IC501 3-IC1003 3-IC1401 3-IC601 3-IC701 3-L802 3-L804 3-L803 3-L801 3-L807 3-L203 4-L851 3-L808 3-L206 3-L205 3-R462 3-R803 3-R805 3-R821 3-R862 3-R1004 3-R1008 3-R1013 3-R1015 3-R1017 3-R1019 3-R1402 3-R301 3-R615 3-R616 3-R661 3-R523 3-R524 3-R662 3-R1025 3-R831 3-R722 3-R614 3-R638 3-R1012 3-R704 3-R603 3-R733 3-R637 3-R1016 3-R1028 3-R314 3-R602 4-R864 3-R376 3-R604 4-R895 3-R304 3-R720 3-R459 3-R608 3-R528 3-R605 3-R753 3-R639 3-R813 3-R507 3-R710 3-R609 3-R612 4-R880

PRICE NEW PART RANK MARK RANK AA AA AA AA AA AB AA AB AB AA AA AB AA AE AE AF AM AB AB AB AB AB AB AB AB AB AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA

R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R

21V1-L(A) PARTS CODE " " VRD-RM2HD333JY VRD-RM2HD393JY VRD-RM2HD680JY " VRN-KT3LB1R8J VRN-RL2HC100J+ VRN-RL2HCR47J+ VRN-RL3AB1R2J+ VRN-RL3AB8R2J+ VRN-RL3DB1R0J+ VRN-RL3DB1R2J+ VRN-RL3DBR22J+ VRN-RL3DBR82J+ VRN-RL3LBR18J+ VRS-CY1JF000JY " " " " " " " " " " " " VRS-CY1JF101JY " " " " " " " " " " " " " VRS-CY1JF102JY " " " " VRS-CY1JF103JY " " " " " " " " " " VRS-CY1JF104JY " " " VRS-CY1JF105JY VRS-CY1JF121JY " " VRS-CY1JF122JY VRS-CY1JF123JY " VRS-CY1JF124JY " VRS-CY1JF152JY " VRS-CY1JF181JY " " VRS-CY1JF182JY " " " VRS-CY1JF183JY

No. 4-R881 4-R882 3-R513 3-R514 3-R601 3-R607 3-R302 3-R621 3-R726 3-R611 3-R754 3-R642 3-R503 3-R706 3-R705 3-R606 3-RJ2 3-RJ5 3-RJ8 3-RJ16 3-RJ17 3-RJ19 3-RJ20 3-RJ24 3-C1012 3-C1846 3-C1847 3-C1849 3-R1087 3-R201 3-R202 3-R804 3-R808 3-R814 3-R815 3-R840 3-R1014 3-R1024 3-R1031 3-R1040 3-R1401 3-R1403 3-R1431 3-R353 3-R801 3-R819 3-R1003 3-R1039 3-R316 3-R373 3-R458 3-R618 3-R810 3-R811 3-R835 3-R1018 3-R1030 3-R1383 3-R1894 3-R372 3-R1010 3-R1027 3-R1045 3-R1041 4-R876 4-R877 4-R878 3-R206 3-R520 3-R617 3-R807 3-R1802 4-R891 4-R894 3-R824 3-R826 3-R827 3-R822 3-R832 3-R833 3-R834 3-R1011

PRICE NEW PART RANK MARK RANK AA AA AA AA AA AA AB AB AB AB AB AB AB AB AD AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA

PARTS CODE

R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R

" " " VRS-CY1JF220JY VRS-CY1JF221JY " VRS-CY1JF222JY " " VRS-CY1JF223JY VRS-CY1JF271JY " " VRS-CY1JF272JY VRS-CY1JF274JY VRS-CY1JF331JY " VRS-CY1JF332JY " " " " " VRS-CY1JF391JY VRS-CY1JF392JY VRS-CY1JF470JY " " " VRS-CY1JF471JY " VRS-CY1JF472JY " " " VRS-CY1JF473JY " " " " " " VRS-CY1JF475JY VRS-CY1JF562JY VRS-CY1JF680JY VRS-CY1JF750JY " VRS-CY1JF822JY " " VRS-RG3AB331J+ VRS-RG3DB121J+ VRS-RG3LB391J+ VRS-RG3LB393J+ VRS-VV3DB124J VRS-VV3DB153J " " VRS-VV3DB682J VS2SA1530AR-1Y " " VS2SC2235Y/1E+ VS2SC2735//1EY VS2SC3198-G-1+ VS2SC3928AR-1Y " " " " " " VS2SD468-C/-1+ " " " VSP9050PA02WA VSTT2140+++-F

13

No. 3-R1020 3-R1022 3-R1026 3-R818 3-R207 3-R220 3-R504 3-R843 3-R1801 3-R828 4-R849 4-R854 4-R855 3-R315 3-R305 3-R208 3-R817 3-R204 3-R366 3-R1032 3-R1056 3-R1074 3-R1384 4-R892 3-R209 3-R841 4-R850 4-R851 4-R852 3-R816 3-R1042 3-R823 3-R838 3-R1046 3-R1092 3-R303 3-R802 3-R825 3-R829 3-R1044 3-R1895 3-R1896 3-R1803 3-R1038 3-R205 3-R461 3-R1432 3-R806 3-R812 3-R1021 3-R506 3-R755 3-R631 3-R216 3-R702 4-R859 4-R861 4-R863 3-R622 3-Q802 3-Q805 4-Q894 3-Q601 3-Q201 3-Q603 3-Q351 3-Q604 3-Q801 3-Q803 3-Q1001 3-Q1002 3-Q1801 3-Q751 3-Q752 3-Q753 3-Q754 5-SP301 3-Q602

PRICE NEW PART RANK MARK RANK AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AB AC AA AA AA AA AA AB AB AB AE AA AB AB AB AB AB AB AB AD AD AD AD AH AG

R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R

21V1-L(A)

14

EndPage

COPYRIGHT SHARP CORPORATION COPYRIGHT © 2008 XXXXBY BYSHARP CORPORATION

ALL RIGHTS RESERVED.

No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, COPYRIGHT © XXXX BYSHARP CORPORATION photocopying, recording, or otherwise, without priorALL written permission of the publisher.

RIGHTS RESERVED.

No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.

RQ0112-S Sept 2008 Printed in Malaysia Design and Production Information Design :SREC Production :SREC CHS.FLE

SHARP-ROXY ELECTRONICS CORPORATION (M) SDN. BHD QRC DEPARTMENT Batu Pahat, Johor, Malaysia P.O.BOX 513 –1