thgirypocybdetcetorP . icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole, isnotpermittedunlessauthorisedbyVolkswagen AG Volkswagen
CLICK HERE TO DOWNLOAD THE COMPLETE MANUAL
• Thank you very much for reading the preview of the manual.
• You can download the complete manual from: www.heydownloads.com by clicking the link below
• Please note: If there is no response to CLICKING the link, please download this PDF first and then click on it.
CLICK HERE TO DOWNLOAD THE
List of Workshop Manual Repair Groups
Repair Group
00 - Technical data
27 - Starter, current supply, CCS
90 - Gauges, instruments
92 - Windscreen wash/wipe system
94 - Lights, bulbs, switches - exterior
96 - Lights, bulbs, switches - interior
97 - Wiring
Technical information should always be available to the foremen and mechanics, because their careful and constant adherence to the instructions is essential to ensure vehicle road-worthiness and safety. In addition, the normal basic safety precautions for working on motor vehicles must, as a matter of course, be observed.
All rights reserved. No reproduction without prior agreement from publisher.
1 Safety information and repair notes
1.2 Repair instructions
2.1 Access to diagnoses
1 Safety information and repair notes
2.1 Assembly overview – battery
2.3
2.5
2.6
2.8
2.9
[V48]/[V49]
2.11 Removing and installing LED module for daytime running light and side light [L176]/[L177] . .68
2.12
[A27]/[A31]
2.13 Removing and installing light conductor for contour lighting in radiator grille [L362]/[L363]
2.14
6.6
6.8 Removing and installing control unit 4 for break-in protection [J1194]/control unit 5 for break-in protection [J1195]
6.9
6.11 Removing and installing entry and start authorisation aerial [R200]/[R201]
7.2
7.3 Removing and installing immobiliser reader coil [D2]
8.1
Assembly overview - automatic headlight range
9 Towing bracket
socket, trailer detector control unit
9.2 Removing and installing trailer detector control unit [J345]
10.1 Removing and installing number plate light [X4]/[X5]
10.2 Assembly overview -
10.5 Assembly overview – lights in exterior door handle
[W52]/[W53]
10.6 Removing and installing bulb for exterior door handle illumination
1.2 Repair instructions
2.1 Overview of fitting locations – lights in dash
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole, isnotpermittedunlessauthorisedbyVolkswagen
[K268]/[K269]
2.10 Removing and installing dynamic light strip 1 for information in
3.8
[EX60]/ [EX61]
4.2 Removing and installing alarm horn [H12]
3.3
3.5
3.6
5.1 Cleaning battery clamp and battery terminal
5.2
5.4 Cleaning threaded connections
6 Wires
6.1 Repairing
7.2
00 –Technical data
1Safety information and repair notes
100056CJ2C47.002.1 - 08.2022
1.1Safety information
Observe safety information ⇒ Safety information and repair notes; Rep. gr. 00; Safety information.
1.2Repair instructions
Observe repair instructions ⇒ Safety and repair instructions; Rep. gr. 00; Repair instructions.
2Electrical components
2.1Access
to diagnoses
Checking battery -A-
♦
Battery monitor control unit -J367- – commissioning
♦ 0019_Functions_Databus_Diagnostic_Interface
♦ 0019_LIN_Nodes
♦ 0637_Commissioning_Battery_Monitor_Control_Unit
Renewing display unit for driver information system
Renewing control unit for head-up display
Activating test screen for calibration of head-up display
Renewing wiper motor
Deactivating APP function
Coding rain and light sensor
Renewing output module
Renewing entry and start authorisation control unit
Parametrisation of anti-theft alarm sensor
Renewing onboard supply control unit
Renewing data bus diagnostic interface
Checking fibre optic cables
27 –Starter, current supply, CCS
1Safety information and repair notes
1.1Safety information
Observe safety information ⇒ Safety information and repair notes; Rep. gr. 00; Safety information.
1.2Repair instructions
Observe repair instructions ⇒ Safety and repair instructions; Rep. gr. 00; Repair instructions.
2Battery
2.1Assembly overview – battery
1 - Battery clamp for positive terminal
❑5 Nm
2 - Positive cable
3 - Cover for positive battery terminal
4 - Nut for positive jump start terminal
❑20 Nm
5 - Cover for negative battery terminal
6 - Nut for negative jump start terminal
❑20 Nm
7 - Earth cable
❑With battery clamp for negative terminal
❑With battery monitoring control unit -J367-
❑⇒ Rep. gr. 27; Remov‐ing and installing earth wire with battery moni‐tor control unit [J367]
❑⇒ Rep. gr. 27; Adapting battery monitor control unit [J367]
❑5 Nm
8 - Battery -A-
thgirypocybde . icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole, isnotpermittedunlessauthorisedbyVolks
❑⇒ Rep. gr. 27; Remov‐ing and installing bat‐tery A
❑⇒ Rep. gr. 27; Discon‐necting and connecting battery
9 - Bolt
❑20 Nm
10 - Retaining clip
11 - Bolt
❑Qty. 3
❑9 Nm
12 - Battery tray
❑⇒ Rep. gr. 27; Removing and installing battery tray
2.2Removing and installing battery A
Special tools and workshop equipment required
system - Edition 08.2022 4 Rep. gr.27 - Starter, current supply, CCS
system - Edition 08.2022
♦ 2D scanner -VAS 6161/1-
WARNING
Leaking battery acid.
Risk of burns to the body and corrosion of the vehicle.
– Wear protective gloves, protective clothing and safety gog‐gles.
– Battery must not be tilted.
– Neutralise sulphuric acid as soon as possible, e.g. with soap solution.
WARNING
Escaping oxyhydrogen gas when charging and due to subse‐quent gas release.
Danger of explosion
– Avoid sparking.
– Avoid short circuits.
– No naked flames.
– Do not smoke.
– No naked light.
– Dissipate any static charge by briefly touching door striker pin.
– Only work on batteries in well ventilated rooms.
– Make sure that the bleeder hole is on the correct side.
WARNING
Danger of explosion when checking and charging battery or when using it for jump starting.
– Do not test or charge batteries whose “ALI (Acid Level In‐dicator)” is colourless/light yellow. Do not slave/jump start the vehicle.
The fuse holder A -SA- will henceforth be referred to as “fuse holder A”.
The battery -A- will henceforth be referred to as “battery”.
Removing
Renew battery
Use only maintenance-free 12-volt vehicle batteries compliant with the standards TL 825 06 and VW 7 50 73. These stand‐ards must be dated October 2014 or later.
thgirypocybdetcetorP . icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole,
If an unsuitable battery is used, the type approval becomes invalid.
Continued
All vehicles (continued)
–Disconnect battery ⇒ Rep. gr. 27; Disconnecting and con‐necting battery.
–Release locking devices -3-.
2020 ➤ Electrical system - Edition 08.2022
–Remove cover for high-voltage connection on vehicle front end -2-.
–Remove cover for high-voltage connection on vehicle front end -1- from guide.
–Release locking devices -arrows-.
thgirypocybdetcetorP
–Remove cover -1-.
–Unscrew nut -2-.
GAnegawskloVybthgirypoC.tnem
–Remove electrical wire -1-.
–Release retaining tabs on bracket for fuse holder A -1- in direction of -arrow-.
–Remove bracket for fuse holder A -1- and lay it aside with electrical wires connected.
–Open cover for battery clamp for positive battery terminal -1-.
–Loosen nut -2- several turns, and pull of battery clamp for positive battery terminal -1-.
–Unscrew bolt -3-.
–Detach retaining strap -2-.
–Pull out battery -1- in direction of travel from battery tray and remove upwards from engine compartment.
Installing
rup op s e s , i n p a r t o r in w ho
Install in the reverse order of removal, observing the following:
For renewal of the battery, record the battery data before bat‐tery installation by writing down the information, photographing
icremmocroetavirprofgniypoC
ID.3 2020 ➤
Electrical system - Edition 08.2022
it or scanning the QR code. The QR code can be captured using 2D scanner -VAS 6161/1-.
Continued –Insert battery in battery tray -1- in such a way that bat‐tery base strip makes contact at bottom and side of stop -arrows-.
Important
• It should no longer be possible to move battery towards rear or sides.
–Fit securing bracket -2-.
Important
• Make sure that the locking element on the securing bracket engages in the recess in the battery base strip.
–Tighten bolt -3-.
–Check battery -1- is seated securely.
–Fit battery clamp for positive battery terminal -1-.
ID.3 2020 ➤
Electrical system - Edition 08.2022
–Tighten nut -2-.
–Connect battery ⇒ Rep. gr. 27; Disconnecting and connect‐ing battery.
If the battery was renewed, perform the test plan for renewal.
Continued
–Carry out function “Renew 12-V battery” using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00; Access to diagnoses.
Tightening torques
♦
⇒ Rep. gr. 27; Assembly overview – battery
♦ ⇒ Rep. gr. 97; Assembly overview – fuse holder A
2.3Disconnecting and connecting battery
WARNING
Leaking battery acid.
Risk of burns to the body and corrosion of the vehicle.
– Wear protective gloves, protective clothing and safety gog‐gles.
– Battery must not be tilted.
– Neutralise sulphuric acid as soon as possible, e.g. with soap solution.
WARNING
Escaping oxyhydrogen gas when charging and due to subse‐quent gas release.
Danger of explosion
– Avoid sparking.
– Avoid short circuits.
– No naked flames.
– Do not smoke.
– No naked light.
– Dissipate any static charge by briefly touching door striker pin.
– Only work on batteries in well ventilated rooms.
– Make sure that the bleeder hole is on the correct side.
The battery monitor control unit -J367- will henceforth be refer‐red to as “battery monitor control unit”.
The battery -A- will henceforth be referred to as “battery”.
Disconnecting
–Deactivate vehicle’s drive system.
. icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole,
–Switch off ignition and electrical equipment.
–Keep vehicle key and other entry and start authorisation devices (e.g. smartphone) outside vehicle.
CLICK HERE TO DOWNLOAD THE COMPLETE MANUAL
• Thank you very much for reading the preview of the manual.
• You can download the complete manual from: www.heydownloads.com by clicking the link below
• Please note: If there is no response to CLICKING the link, please download this PDF first and then click on it.
CLICK HERE TO DOWNLOAD THE
Electrical system - Edition 08.2022
Vehicles with refrigerant R744
WARNING
Risk of suffocation from refrigerant R744
When work is performed on the vehicle with the 12 V battery disconnected, the sensor for interior carbon dioxide concen‐tration is disabled.
– Only work in interior with all doors open.
–Observe safety precautions for working on air conditioning systems.
All vehicles (continued)
–Open cover for negative battery terminal above battery mon‐itor control unit -3-.
AGdoesnotguaranteeoracceptanyli
–Loosen nut -1- several turns, and pull battery monitor control unit -3- off negative battery terminal.
–Disconnect electrical connector -2- from battery monitor con‐trol unit -J367-.
–Wait for 1 minute.
–Use a commercially available voltage tester to check voltage of 12 V electrical system.
Important
• The voltage must be 0 V.
Vehicles with voltage > 0 V
–⇒ ; Rep. gr. ; De-energise high-voltage system.
Important
thgirypocybdetcetorP . icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole,
–Use a commercially available voltage tester to check voltage of 12 V electrical system.
• The voltage must be 0 V.
All vehicles (continued)
Connecting
NOTICE
Risk of damage to the battery clamps for positive and nega‐tive battery terminals and to the battery terminals themselves.
– Battery clamps for positive and negative battery terminals may only be attached by hand without excessive force.
– Battery terminals must not be greased.
– Battery clamps for positive and negative battery terminals must be installed in such a way that the battery terminal is flush with the battery clamp or protrudes from it.
–Fit battery monitor control unit -3- on negative battery termi‐nal.
–Tighten nut -1-.
–Connect electrical connector -2- from battery monitor control unit -J367-.
–Switch on ignition.
–Open and close door windows to fully opened and fully closed position respectively.
–Then, when door windows are closed, pull the window regu‐lator buttons until the relay audibly switches.
–Check convenience mode of the window regulator motors.
Important
• With “one-touch opening and closing” activated, door win‐dows must close fully without the need to hold window regu‐lator button.
This following work steps are necessary so that the ESP indica‐tor lamp goes out:
–Activate vehicle’s drive system.
–Select drive position.
–Move steering wheel to full left and right lock.
–Read and clear event memory using ⇒ Vehicle diagnostic tester.
Important
• ESC warning lamp must go out.
Tightening torques
♦ ⇒ Rep. gr. 27; Assembly overview – battery
system - Edition 08.2022
2.4Removing and installing battery tray
Removing
–Remove battery -A- ⇒ Rep. gr. 27; Removing and installing battery A.
–Unscrew bolts -2-.
–Remove cable tie from battery tray -1-.
–Remove battery tray -1-.
Installing
Install in reverse order of removal, observing the following:
Tightening torques
♦ ⇒ Rep. gr. 27; Assembly overview – battery
2.5Checking battery A
2.5.1Sequence for checking battery A
– ⇒ i2.5.2 nspection of battery A”, page 12
– ⇒ c2.5.3 olour indicator of battery A”, page 13
⇒ b2.5.4 attery A”, page 14
2.5.2Visual inspection of battery A
WARNING
Leaking battery acid.
Risk of burns to the body and corrosion of the vehicle.
– Wear protective gloves, protective clothing and safety gog‐gles.
– Battery must not be tilted.
– Neutralise sulphuric acid as soon as possible, e.g. with soap solution.
WARNING
Escaping oxyhydrogen gas when charging and due to subse‐quent degassing.
Danger of explosion
– Avoid sparking.
– Avoid short circuits.
– No open flames.
– No smoking.
– No open light.
– Dissipate any static charge by briefly touching door striker pin.
– Only work on batteries in well ventilated rooms.
– Make sure that the bleeder hole is on the correct side.
–Perform visual inspection of battery housing for damage.
–Perform visual inspection of battery terminals for damage.
–Perform visual inspection of whether the hose for central gas venting system and the sealing plug are fitted correctly.
2.5.3Checking colour indicator of battery A
WARNING
Danger of explosion when checking and charging battery or when using it for jump starting.
– Do not test or charge batteries whose “ALI (Acid Level In‐dicator)” is colourless/light yellow. Do not slave/jump start the vehicle.
Note
The colour indicator shows the electrolyte level in the battery.
Note
Since the colour indicator is only located in one battery cell, the indicator also only applies to this battery cell. Under normal circumstances, the result of the colour indicator check is repre‐sentative of all six cells of the battery. Thus, the battery does not need to be removed. The colour indicator check cannot be replaced by the check conducted with the vehicle diagnostic tester.
–Before the visual inspection, tap the “ALI (Acid Level Indica‐tor” lightly and carefully using the handle of a screwdriver. The air bubbles, which can influence the display, will dissi‐pate when doing this. The colour display of the “ALI (Acid Level Indicator)” will now be more accurate.
–“ALI (Acid Level Indicator)” visual inspection
Important
• Do not use flashlights.
Important
thgirypocybdetcetorP . icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole,
• Black = electrolyte level is OK.
• Look at the electrolyte level indicator vertically from above. Three different colour displays are possible:
ID.3 2020 ➤ Electrical system - Edition 08.2022
• Light yellow = electrolyte level is too low. Battery must be renewed.
2.5.4Checking
battery A
WARNING
Escaping oxyhydrogen gas when charging and due to subse‐quent degassing.
Danger of explosion
– Avoid sparking.
– Avoid short circuits.
– No naked flames.
– No smoking.
– No naked light.
– Discharge any static electricity by briefly touching door striker pin.
– Only work on batteries in well ventilated rooms.
– Make sure that the bleeder hole is on the correct side.
Vehicles with colour indicator
– ⇒ c2.5.3 olour indicator of battery A”, page 13
All vehicles (continued)
WARNING
Danger of explosion when checking and charging battery or when using it for jump starting.
– Do not test or charge batteries whose “ALI (Acid Level In‐dicator)” is colourless/light yellow. Do not slave/jump start the vehicle.
–Carry out function “Battery test” using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00; Access to diagnoses.
2.6Charging battery A
WARNING
Escaping oxyhydrogen gas when charging and due to subse‐quent degassing.
Danger of explosion
– Avoid sparking.
– Avoid short circuits.
– No naked flames.
– No smoking.
– No naked light.
la rup op s e s , i n p a r t o r in w hole,
– Discharge any static electricity by briefly touching door striker pin.
– Only work on batteries in well ventilated rooms.
– Make sure that the bleeder hole is on the correct side.
NOTICE
Risk of damage to battery -A-
– Charge battery -A-. The no-load voltage must not be less than 11.6 V.
The battery monitor control unit -J367- will henceforth be refer‐red to as “battery monitor control unit”.
The battery -A- will henceforth be referred to as “battery”.
A battery is designated totally discharged when the no-load voltage is less than 11.6 V.
Important
• The battery must have a temperature of at least 10°C.
–Switch off ignition and electrical consumers.
–Keep vehicle key and other entry and start authorisation devices (e.g. smartphone) outside vehicle.
WARNING
Danger of explosion when checking and charging battery or when using it for jump starting.
– Do not test or charge batteries whose “ALI (Acid Level In‐dicator)” is colourless/light yellow. Do not slave/jump start the vehicle.
–Switch on battery charger.
–Select charging mode.
CAUTION
Short circuit to earth possible. Danger of battery exploding.
– Use only insulated terminal clamps.
–Connect red charger terminal “+” to positive battery terminal.
–Connect black charger terminal “-” to vehicle earth of jumpstart connection.
Ending battery charging process
–Switch off battery charger.
–Disconnect black terminal “-” of battery charger.
–Disconnect red terminal “+” of battery charger.
2.7Removing and installing earth wire with battery monitor control unit [J367]
The battery monitor control unit -J367- will henceforth be refer‐red to as “battery monitor control unit”.
Removing
–Disconnect battery ⇒ Rep. gr. 27; Disconnecting and con‐necting battery.
–Disconnect electrical connector -2- from battery monitor con‐trol unit -3-.
–Unscrew nut -1- from earth cable -2-.
–Detach earth wire along with battery monitor control unit [J367].
Installing
thgirypocybdetcetorP . icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w ho
Install in the reverse order of removal, observing the following:
–⇒ Rep. gr. 27; Adapt battery monitor control unit [J367].
Tightening torques
♦ ⇒ Rep. gr. 27; Assembly overview – battery
2.8Commissioning battery monitor control unit [J367]
The battery monitor control unit -J367- is referred to hereafter as battery monitor control unit.
–Carry out function “Commission battery monitor control unit” using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00; Access to diagnoses.
90 –Gauges, instruments
1Safety information and repair notes
1.1Safety information
Observe safety information ⇒ Safety information and repair notes; Rep. gr. 00; Safety information.
1.2Repair instructions
Observe repair instructions ⇒ Safety and repair instructions; Rep. gr. 00; Repair instructions.
ID.3 2020 ➤ Electrical system - Edition 08.2022
2Dash panel insert
2.1Assembly overview ? control unit with display unit for driver information system
1 - Gap cover for dash panel insert
❑⇒ General body re‐pairs, interior; Rep. gr. 68; Compart‐ments/covers; Assem‐bly overview – steering column trim
2 - Trim for control unit with display unit for driver informa‐tion system -J1254-
3 - Bolt
❑qty. 6
❑3 Nm
4 - Steering column electron‐ics control unit -J527-
❑⇒ Rep. gr. 94; Remov‐ing and installing steer‐ing column electronics control unit [J527]
5 - Control unit with display unit for driver information sys‐tem -J1254-
❑⇒ Rep. gr. 90; Remov‐ing and installing con‐trol unit with display unit for driver informa‐tion system [J1254]
6 - Upper steering column trim
❑⇒ General body re‐pairs, interior; Rep. gr. 68; Compart‐ments/covers; Assem‐bly overview – steering column trim
7 - Electrical connector for control unit with display unit for driver information system -J1254-
2.2Assembly overview - head-up display
1 - Dash panel trim
❑⇒ General body re‐pairs, interior; Rep. gr. 70; Dash panel; Assembly overview –dash panel
2 - Bolt
❑Qty. 6
❑1.2 Nm
3 - Bolt
❑Qty. 4
❑4.5 Nm
4 - Control unit for head-up display - J898-
❑⇒ Rep. gr. 90; Remov‐ing and installing con‐trol unit for head-up dis‐play [J898]
❑⇒ Rep. gr. 90; Cali‐brating control unit for head-up display [J898]
5 - Central tube for dash pan‐el
op s e s , i n p a r t o r in w hole, isnotpermittedunlessauthorisedbyVolkswage
la rup
Electrical system - Edition 08.2022
2.3Removing and installing control unit with display unit for driver information system [J1254]
The control unit with display unit for driver information system -J1254- will henceforth be referred to as “display unit for driver information system”.
Removing
If the display unit for driver information system is renewed, per‐form the test plan for the renewal of the display unit for driver information system:
–Carry out function “Renew display unit for driver information system” using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00; Access to diagnoses.
ID.3 2020 ➤
Electrical system - Edition 08.2022
Continued
–Move steering wheel to rearmost and lowest position. Use the full range of the steering column adjustment for this pur‐pose.
–Remove gap cover for dash panel insert ⇒ General body re‐pairs, interior; Rep. gr. 68; Compartments/covers; Removing and installing dash panel insert gap cover.
–Use a commercially available plastic wedge to unclip trim -1-.
–Disconnect electrical connector -2-.
–Secure display unit for driver information system against fall‐ing out.
–Unscrew bolts -1-.
–Remove display unit for driver information system.
Installing
Install in the reverse order of removal, observing the following: Tightening torques
♦ ⇒ Rep. gr. 90; Assembly overview – control unit with display unit for driver information system
2.4Removing and installing control unit for head-up display [J898]
Special tools and workshop equipment required
♦ Torque screwdriver -V.A.G 1624-
The control unit for head-up display -J898- will henceforth be referred to as “control unit for head-up display”.
The dynamic light strip 1 for information in dash panel -L385will henceforth be referred to as “dynamic light strip”.
20 Rep. gr.90 - Gauges, instruments
system - Edition 08.2022
If the control unit for head-up display is renewed, perform the test plan for the renewal of the control unit for head-up display using ⇒ Vehicle diagnostic tester.
Removing
If the control unit for head-up display is renewed, perform the test plan for the renewal of the control unit for head-up display:
–Carry out function “Renewing control unit for head-up dis‐play” using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00; Ac‐cess to diagnoses.
Continued
–Remove windscreen ⇒ General body repairs, exterior; Rep. gr. 64; Windscreen; Removing and installing windscreen.
–Remove dynamic light strip ⇒ a2.10 nd installing dynamic light strip 1 for information in dash panel [L385]”, page 116
–Remove cover for head-up display ⇒ General body repairs, interior; Rep. gr. 70; Dash panel; Removing and installing dash panel trim.
–Place dash panel insulation to one side.
–Cover control unit for head-up display -1- with a soft cloth.
isnotpermittedunlessauthorisedbyVolkswagen
AG Volkswagen AGdoesn
–Unscrew bolts -arrows-.
–Remove control unit for head-up display -1- until the electri‐cal connectors are accessible.
–Disconnect electrical connectors.
–Remove control unit for head-up display -1-.
Installing
Install in the reverse order of removal, observing the following: If the control unit for head-up display has been renewed.
–On new part, unscrew bolts -2-.
ID.3 2020 ➤ Electrical system - Edition 08.2022
–Remove actuator plates -3- from control unit for head-up display -1-.
All vehicles (continued)
NOTICE
Risk of damage to control unit for head-up display.
– Never apply pressure to the upper part of the housing when inserting.
– Should a control unit for head-up display fall down, it must be renewed.
–Insert control unit for head-up display -1-.
thgirypocybdetcetorP
–Connect electrical connectors.
–Tighten bolts -arrows-.
–Position windscreen and secure it temporarily with adhesive tape – do not bond it in yet.
–Switch on ignition.
–Perform functional check.
–Install windscreen ⇒ General body repairs, exterior; Rep. gr. 64; Windscreen; Removing and installing windscreen.
–Calibrate control unit for head-up display ⇒ Rep. gr. 90; Calibrating control unit for head-up display [J898].
22 Rep. gr.90 - Gauges, instruments
Tightening torques
Continue installation in reverse sequence of removal, observing the following:
♦ ⇒ Rep. gr. 90; Assembly overview – head-up display
2.5Calibrating control unit for head-up dis‐play [J898]
2.5.1Calibrating control unit for head-up dis‐play [J898], left-hand drive vehicles
Special tools and workshop equipment required
♦ Calibration board for head-up display AR -VAS 721 017-
♦ Setting device -VAS 6430-
The control unit for head-up display -J898- will henceforth be referred to as “control unit for head-up display”.
Calibrate control unit for head-up display, if:
♦ Installation position of dash panel cross member has been changed
♦ Dash panel cross member was removed and installed
♦ Windscreen was removed and reinstalled.
♦ Control unit for head-up display has been removed and then reinstalled or it has been renewed.
Calibration
–⇒ Driver assist systems; Rep. gr. 98; Front camera for driver assist systems; Calibrating front camera for driver assist sys‐tems [R242].
–On the display unit for front information display and operat‐ing unit control unit -J685-, select the lower limit position for the head-up display control unit, and then increase the setting by 10 increments.
isnotpermittedunlessauthorisedbyVolkswagen AG Volkswagen AGdoesnotguaranteeoracceptanyliabilitywi
–Fold down left and right sun visors, detach and swivel to one side.
–Attach calibration board for head-up display AR -VAS 721 017- -1- to sun visor centre mount -2-, and align it centrally.
thgirypocybdetcetorP . icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole,
–Remove cover for dash panel/head-up display ⇒ General body repairs, interior; Rep. gr. 70; Removing and installing cover for dash panel/head-up display.
–Carry out function “Activate test screen” using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00; Access to diagnoses.
CLICK HERE TO DOWNLOAD THE COMPLETE MANUAL
• Thank you very much for reading the preview of the manual.
• You can download the complete manual from: www.heydownloads.com by clicking the link below
• Please note: If there is no response to CLICKING the link, please download this PDF first and then click on it.
CLICK HERE TO DOWNLOAD THE
ID.3 2020 ➤
Electrical system - Edition 08.2022
–Check position of test screen through hole on driver side of calibration board for head-up display AR -VAS 721 017--1-.
Vehicles with incorrectly positioned test screen
Note
During manual adjustment, it may happen that not all contours of the head-up display test screen can be positioned well on the setting device -VAS 6430-. This is due to the tolerances in the head-up display system and the resulting distortion. In this case, mainly the elements in the middle of the image area should be brought into the best possible alignment. Deviations for elements in the outer image area are allowed.
–Use setting device -VAS 6430- -A-, to bring test screen -1into the best possible alignment using adjuster screws -3- on control unit for head-up display -2-.
isnotpermittedunlessauthorisedbyVolkswagen
All vehicles (continued)
Installing
Install in reverse order of removal.
2.5.2Calibrating control unit for head-up dis‐play [J898], right-hand drive vehicles
Special tools and workshop equipment required
♦ Calibration board for head-up display AR -VAS 721 017-
♦ Setting device -VAS 6430-
The control unit for head-up display -J898- will henceforth be referred to as “control unit for head-up display”.
Calibrate control unit for head-up display, if:
♦ Installation position of dash panel cross member has been changed
♦ Dash panel cross member was removed and installed
♦ Windscreen was removed and reinstalled.
♦ Control unit for head-up display has been removed and then reinstalled or it has been renewed.
Calibration
–⇒ Driver assist systems; Rep. gr. 98; Front camera for driver assist systems; Calibrating front camera for driver assist sys‐tems [R242].
–On the display unit for front information display and operat‐ing unit control unit -J685-, select the lower limit position for the head-up display control unit, and then increase the setting by 10 increments.
–Fold down left and right sun visors, detach and swivel to one side.
–Attach calibration board for head-up display AR -VAS 721 017- -1- to sun visor centre mount -2-, and align it centrally.
–Remove cover for dash panel/head-up display ⇒ General body repairs, interior; Rep. gr. 70; Removing and installing cover for dash panel/head-up display.
–Carry out function “Activate test screen” using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00; Access to diagnoses.
–Check position of test screen through hole on driver side of calibration board for head-up display AR -VAS 721 017- -1-.
Vehicles with incorrectly positioned test screen
Note
During manual adjustment, it may happen that not all contours of the head-up display test screen can be positioned well on the setting device -VAS 6430-. This is due to the tolerances in the head-up display system and the resulting distortion. In this case, mainly the elements in the middle of the image area should be brought into the best possible alignment. Deviations for elements in the outer image area are allowed.
–Use setting device -VAS 6430- -A-, to bring test screen -1into the best possible alignment using adjuster screws -3- on control unit for head-up display -2-.
Electrical system - Edition 08.2022
All vehicles (continued)
Installing
Install in reverse order of removal. ID.3 2020
system - Edition 08.2022
3Horn
3.1Assembly overview – horn
1 - Horn or dual tone hornH1-
❑⇒ Rep. gr. 90; Remov‐ing and installing horn or dual tone horn [H1]
2 - Nut
❑14 Nm
3 - Electrical connector
4 - Bolt
❑6 Nm
5 - Bracket for horn or dual tone horn -H1-
3.2Removing and installing horn or dual tone horn [H1]
The horn or dual tone horn -H1- will henceforth be referred to as “horn”.
Removing
–Remove front right wheel housing liner ⇒ General body re‐pairs, exterior; Rep. gr. 66; Wheel housing liner; Removing and installing front wheel housing liner.
–Disconnect connector -2-.
ID.3 2020 ➤
Electrical system - Edition 08.2022
–Unscrew bolt -3-.
–Remove horn -1-.
Installing
Install in the reverse order of removal, observing the following:
Tightening torques
♦ ⇒ Rep. gr. 90; Assembly overview – horn
thgirypocybdetcetorP . icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole, isnotpermittedunlessauthorisedbyVolkswagen
92 –Windscreen wash/wipe system
1Safety information and repair notes
1.1Safety information
Observe safety information ⇒ Safety information and repair notes; Rep. gr. 00; Safety information.
1.2Repair instructions
Observe repair instructions ⇒ Safety and repair instructions; Rep. gr. 00; Repair instructions.
2Windscreen wiper system
2.1Assembly overview – windscreen wiper system
The overview shows a left-hand drive vehicle as an example.
1 - Left wiper blade
❑⇒ Rep. gr. 92; Remov‐ing and installing wiper blade
2 - Left wiper arm
❑⇒ Rep. gr. 92; Remov‐ing and installing wiper arms
❑⇒ Rep. gr. 92; Adjust‐ing wiper arms
3 - Cap
4 - Nut
❑30 Nm
5 - Bolt
❑Observe tightening se‐quence
❑Qty. 3
❑Specified torque and tightening sequence ⇒ page 31
6 - Driver side windscreen wiper motor -V216-
❑⇒ Rep. gr. 92; Remov‐ing and installing wiper motor [V]
7 - Right wiper blade
❑⇒ Rep. gr. 92; Remov‐ing and installing wiper blade
8 - Right wiper arm
❑⇒ Rep. gr. 92; Remov‐ing and installing wiper arms
❑⇒ Rep. gr. 92; Adjusting wiper arms
9 - Bolt
❑Observe tightening sequence
❑Qty. 3
❑Specified torque and tightening sequence ⇒ page 31
10 - Front passenger side windscreen wiper motor -V217-
11 - Nut
❑30 Nm
12 - Cap
Removing and installing windscreen wiper motor - specified tor‐que and tightening sequence
Stage Component Specified torque/turning further angle
1. -1-, -2- and -3- Screw in by hand to stop
2. -1-, -2- and -3- 8 Nm
2.2Moving wipers to service position
NOTICE
Risk of damaging the bonnet when moving wipers back into the park position.
– Never move vehicle with wiper arms folded out.
NOTICE
Risk of damage from movement of frozen wiper blades.
– Allow wiper blades to thaw before operating.
Important
icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole,
• The wiper motor only works when the bonnet is fully closed.
thgirypocybdetcetorP
–When there is a risk of frost, check if wiper blades are frozen to windscreen.
–Switch ignition on and off.
–Press windscreen wiper lever to “flick wipe” position within 10 seconds.
Important
• Wipers move to service position.
2.3Removing and installing wiper blade
NOTICE
Risk of damage to windscreen.
– Prevent the wiper arm folding back unexpectedly.
Electrical system - Edition 08.2022
NOTICE
Risk of damage to the wiper blade.
– To lift wiper blade off windscreen, touch it only in area in which wiper blade is attached to wiper.
– Avoid bending wiper arm and wiper blade.
Removing
–⇒ Rep. gr. 92; Move wipers to service position.
–Lift wiper arm off the windscreen.
–Release retaining clip in direction of -arrow A-.
–Pull wiper blade -1- in direction of -arrow B- off wiper arm -2-.
Installing
Install in reverse order of removal, observing the following:
–Insert wiper blade -1- parallel in direction of -arrow- into wiper arm -2-.
–Push wiper blade -1- into wiper arm -2- until retaining clip is heard to engage.
–Activate “flick wipe” function to exit the service position.
2.4Removing and installing wiper arms
Special tools and workshop equipment required
♦ Extracting tool -T10369/5-
Removal and installation are described for a left-hand drive vehicle as an example.
Removing
–⇒ Rep. gr. 92; Move wipers to service position. ID.3
Electrical system - Edition 08.2022
–Use a suitable screwdriver to lever caps -3- off wiper arms -1-.
–Loosen nuts -2- a few turns.
–Move wiper arms -1- to upper turning point.
–Mount puller -T10369/5- -A- on wiper arm -1-.
–Position thrust piece -3- on wiper motor shaft.
–Turn spindle -2- clockwise until wiper arm -1- is pulled off wiper motor shaft.
–Remove puller -T10369/5- -A- from wiper arm -1-.
–Unscrew nut.
–Remove wiper arm -1-.
Installing
Install in the reverse order of removal, observing the following:
–Switch on ignition.
–⇒ Rep. gr. 92; Code wiper motor.
ID.3
ID.3 2020 ➤
Electrical system - Edition 08.2022
–Actuate “flick wipe” function and allow wiper arms to move to their end position.
–Fit both wiper arms in approximate park positions on wiper arm shafts.
When attaching the wiper arm to the wiper motor, the wiper motor must be in park position. To ensure this, the wiper motor must be coded to switch off the APP function to deactivate the alternating park position.
Note
It is not possible to activate the alternating park position.
Note
If the wiper motor is new or the alternating park position function of the wiper motor has been deactivated, the alternating park position function will be activated automatically after 100 wipe cycles.
–Carry out “Deactivate APP function” with ⇒ Vehicle diagnos‐tic tester ⇒ Rep. gr. 00; Access to diagnoses. ID.3 2020 ➤
2020 ➤
Electrical system - Edition 08.2022
2.8Removing and installing rain and light sensor [G397]
The rain and light sensor -G397- with humidity sender for air conditioning system -G260- and sunlight penetration photosen‐sor -G107- will henceforth be referred to as “rain and light sen‐sor”.
Removing
If the rain and light sensor is renewed with a rain and light sensor having a different part number, the new rain and light sensor needs to be coded:
–Carry out function “Renew rain and light sensor” using ⇒ Ve‐hicle diagnostic tester ⇒ Rep. gr. 00; Access to diagnoses.
Continued
–Remove interior mirror ⇒ General body repairs, interior; Rep. gr. 68; Interior mirror; Removing and installing interior mirror.
–Separate electrical connector -3-.
–Release fasteners -arrows-.
NOTICE
Risk of damage to the coupling pad if removal is done too abruptly.
– Wait at least 1 minute to allow the coupling pad to decom‐press.
–Starting at top, carefully pry rain and light sensor -2- out of interior mirror retaining plate.
–Remove rain and light sensor -2-.
Installing
Install in the reverse order of removal, observing the following:
–Thoroughly clean windscreen in area of interior mirror retain‐ing plate.
When reinstalling old rain and light sensor
–Pull off coupling pad -2- in direction of -arrow-.
ID.3
CLICK HERE TO DOWNLOAD THE COMPLETE MANUAL
• Thank you very much for reading the preview of the manual.
• You can download the complete manual from: www.heydownloads.com by clicking the link below
• Please note: If there is no response to CLICKING the link, please download this PDF first and then click on it.
CLICK HERE TO DOWNLOAD THE
Electrical system - Edition 08.2022
NOTICE
Risk of damage to silicone layer of rain and light sensor.
– Clean the surface of the rain and light sensor thoroughly.
–Clean rain and light sensor -1- by sticking and then peeling off one or several commercially available adhesive strips on bonding surface of rain and light sensor -1-.
–Clean bonding surface of rain and light sensor -1- using a lint-free cleaning cloth.
–Pull silicone paper -1- off coupling pad -3-.
Important
• Protective film -2- must remain on coupling pad -3-.
thgirypocybdetcetorP
–With aid of protective film -1-, align coupling pad -2- centrally on rain and light sensor -3-.
–Press on coupling pad -2- with protective film -1-.
–Pull off backing -2-.
When installing new rain and light sensor –Press grip in direction of arrows -A-.
–Remove protective cap -1- in direction of -arrow B-. All vehicles (continued)
–Insert rain and light sensor -2- into retaining plate for interior mirror.
isnotpermittedunlessauthorisedbyVolkswagen AG Volkswagen AGdoesnotg
thgirypocybdetcetorP . icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole,
ID.3 2020 ➤
2020 ➤
Electrical system - Edition 08.2022
NOTICE
Malfunctions of rain and light sensor.
– If the contact surface is not free of bubbles after 10 mi‐nutes, the rain and light sensor must be removed and inserted anew.
–Engage retaining clip -1- so that it can be heard to engage.
–Connect electrical connector -3-.
If the rain and light sensor has been renewed, the new rain and light sensor must be coded:
–Carry out function “Renew rain and light sensor” using ⇒ Ve‐hicle diagnostic tester ⇒ Rep. gr. 00; Access to diagnoses.
Volkswagen
. icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole, isnotpermittedunlessauthorisedbyVolkswagen
ID.3
system - Edition 08.2022
3Windscreen washer system
3.1Assembly overview – windscreen washer system
1 - Right spray jet
❑Depending on equip‐ment/installation period with right washer jet heater element -Z21-
❑⇒ Rep. gr. 92; Remov‐ing and installing spray jets
❑⇒ Rep. gr. 92; Adjust‐ing spray jets
2 - Left spray jet
❑Depending on equip‐ment/installation period with left washer jet heater element -Z20-
❑⇒ Rep. gr. 92; Remov‐ing and installing spray jets
❑⇒ Rep. gr. 92; Adjust‐ing spray jets
3 - Electrical connector for right washer jet heater ele‐ment -Z21-
❑Depending on equip‐ment/installation period
4 - Electrical connector for left washer jet heater element -Z20-
❑Depending on equip‐ment/installation period
5 - Grommet
6 - Hose for washer fluid
7 - Windscreen and rear win‐dow washer pump -V59-
❑⇒ Rep. gr. 92; Removing and installing washer pump [V59]
8 - Sealing grommet
9 - Connection for washer fluid hose
10 - Washer fluid reservoir
❑With windscreen washer fluid level sender -G33-
❑⇒ Rep. gr. 92; Removing and installing washer fluid reservoir
11 - Bolt
❑Qty. 3
❑8 Nm
12 - Strainer
13 - Filler neck sealing cap
Electrical system - Edition 08.2022
3.2Removing and installing washer fluid reservoir
The windscreen and rear window washer pump -V59- will henceforth be referred to as “windscreen and rear window washer pump”.
Removing
–Remove front left wheel housing liner ⇒ General body re‐pairs, exterior; Rep. gr. 66; Wheel housing liners; Removing and installing front wheel housing liners.
–Remove front bumper cover ⇒ General body repairs, exte‐rior; Rep. gr. 63; Front bumper; Removing and installing bumper cover.
–Place commercially available drip tray under washer fluid reservoir.
–Release locking lug -2-.
NOTICE
Risk of leakage.
la rup op s e s , i n p a r t o r in w hole,
.GAnegawsk
–Pull filler neck -1- upwards out of bracket on lock carrier -3-.
– The washer fluid reservoir and the filler neck are not inten‐ded to be separated from each other.
–Disconnect connectors -2- and -5-.
–Release and pull off washer fluid hoses -4- on windscreen and rear window washer pump -3-.
–Pull retainer -1- for wiring harness off washer fluid reservoir.
–Unscrew bolts -1-. ID.3 2020 ➤
system - Edition 08.2022
–Pull washer fluid reservoir -2- off guide rails, and remove it.
Installing
Install in the reverse order of removal, observing the following:
Note
To prevent incorrect connection of the washer fluid hoses on the windscreen and rear window washer pump, the connec‐tions on the windscreen and rear window washer pump and washer fluid hoses are colour-coded. The connection pieces of the washer fluid hoses must be inserted in the corresponding colour-coded connections of the windscreen and rear window washer pump during installation.
The windscreen and rear window washer pump -V59- will henceforth be referred to as “windscreen and rear window washer pump”.
Removing
–Detach front left wheel housing liner ⇒ General body repairs, exterior; Rep. gr. 66; Wheel housing liner; Removing and installing front wheel housing liner.
thgirypocybdetcetorP . icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole, isnotpermittedunlessauthorisedbyVolkswagen
–Place commercially available drip tray under washer fluid reservoir.
–Disconnect electrical connector -2-.
AG. Volkswagen
Electrical system - Edition 08.2022
–Pull out windscreen and rear window washer pump -1- up‐wards.
–Release and pull off washer fluid hoses -3-.
Installing
Install in reverse order of removal, observing the following:
Note
To prevent incorrect connection of the washer fluid hoses on the windscreen and rear window washer pump, the connec‐tions on the windscreen and rear window washer pump and washer fluid hoses are colour-coded. The connection pieces of the washer fluid hoses must be inserted in the corresponding colour-coded connections of the windscreen and rear window washer pump during installation.
–Check sealing grommet for damage and correct seating.
3.4Removing and installing spray jets
The left spray jet heater element -Z20- and right spray jet heater element -Z21- are an integral part of the spray jets.
Removing –Open bonnet.
. icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole,
–Push spray jet upwards in direction of -arrow A-.
–Swivel spray jet downwards out of bonnet in direction of -arrow B-.
–Release securing clip -1- in direction of -arrow-.
–Pull off washer fluid hose connection -2-.
–Disconnect electrical connector -4-.
–Remove spray jet -3-.
Installing
Install in reverse order of removal, observing the following: NOTICE
Leaks from connection for washer fluid hose.
– When connecting washer fluid hose, securing clip must engage audibly in connection for washer fluid hose.
–Starting at the top, push spray jet into mounting hole in bonnet until spray jet is heard to engage.
–⇒ Rep. gr. 92; Adjust spray jets.
3.5Adjusting spray jets
–Adjust spray jets ⇒ Maintenance; Booklet ; Window wash/ wipe system and headlight washer system: checking func‐tion.
isnotpermittedunlessauthorisedbyVolkswagen
la rup op s e s , i n p a r t o r in w hole,
4Rear window wiper system
4.1Assembly overview – rear window wiper system
1 - Cap
2 - Nut
❑12 Nm
3 - Wiper arm
❑⇒ Rep. gr. 92; Remov‐ing and installing wiper arm
4 - Wiper blade
❑⇒ Rep. gr. 92; Remov‐ing and installing wiper blade
5 - Seal in rear window
6 - Spacer
❑Qty. 3
7 - Rubber ring
❑Qty. 3
8 - Bolt
❑Qty. 3
❑8 Nm
9 - Rear window wiper motor -V12-
❑⇒ Rep. gr. 92; Remov‐ing and installing rear window wiper motor [V12]
4.2Removing and installing wiper blade
NOTICE
Risk of damage to rear window.
thgirypocybdetcetorP . icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole, isnotpermittedunlessauthorisedbyVolkswagen A
– Prevent the wiper arm folding back unexpectedly.
NOTICE
Risk of damage to the wiper blade.
– To lift wiper blade off rear window, touch it only in area in which wiper blade is attached to wiper.
system - Edition 08.2022
NOTICE
Risk of damage to wiper arm and wiper blade.
– Avoid bending wiper arm and wiper blade.
Removing
–Lift wiper arm off the rear window.
–Swivel wiper blade -1- in direction of -arrow A- out of wiper arm.
–Release retaining clip -2-.
–Pull wiper blade -1- in -direction of arrow B- out of washer wiper arm.
Installing
Install in reverse order of removal, observing the following:
Important
• Push wiper blade into wiper arm until retaining clip is heard to engage.
–Loosen wiper arm ⇒ Rep. gr. 92; Removing and installing wiper arm.
Distance -a- from end of wiper blade to bottom edge of rear window must be 31 +/-5 mm.
–Adjust wiper blade park position by repositioning wiper arm -1-.
–Tighten nut of wiper arm -1-.
–Switch on ignition.
–Actuate “rear window wipe” function and allow wiper arm to move to its end position.
–Check adjustment of wiper arm.
Tightening torques
thgirypocybdetcetorP . icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole, isnotpermittedunlessauthorisedbyVolkswagen AG Volkswagen
❑⇒ General body re‐pairs, exterior; Rep. gr. 66; Spoilers; Re‐moving and installing spoiler trim
2 - Spray jet
❑⇒ Rep. gr. 92; Remov‐ing and installing spray jet, rear window washer system
3 - Hose for washer fluid
❑In left side panel to spray jet of rear window washer system
4 - Hose for washer fluid
❑In engine compartment to spray jet of rear win‐dow washer system
5 - Washer fluid reservoir
❑⇒ Rep. gr. 92; Remov‐ing and installing wash‐er fluid reservoir
6 - Windscreen and rear win‐dow washer pump -V59-
❑⇒ Rep. gr. 92; Remov‐ing and installing wind‐screen washer pump
❑With sealing grommet
system - Edition 08.2022
5.2Removing and installing spray jet, rear window washer system
Removing
–Remove trim for rear spoiler ⇒ General body repairs, exte‐rior; Rep. gr. 66; Spoilers; Removing and installing spoiler trim.
–Release and pull off washer fluid hose -3-. ID.3
CLICK HERE TO DOWNLOAD THE COMPLETE MANUAL
• Thank you very much for reading the preview of the manual.
• You can download the complete manual from: www.heydownloads.com by clicking the link below
• Please note: If there is no response to CLICKING the link, please download this PDF first and then click on it.
CLICK HERE TO DOWNLOAD THE
ID.3 2020 ➤
Electrical system - Edition 08.2022
–Release fasteners -2-.
–Pull out spray jet -1-.
Installing
Install in the reverse order of removal, observing the following:
When connecting washer fluid hose, securing clip must be heard to engage in connection for washer fluid hose.
thgirypocybdetcetorP . icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole, isnotpermittedunlessauthorisedbyVolkswagen AG Volkswagen
AGdoesnotguaranteeoracceptanyliabilitywi
GAnegawskloVybthgirypoC.tnemucodsihtninoitamrof
6Washer fluid lines
6.1Repairing washer fluid lines
6.1.1Pulling off and fitting washer fluid ho‐ses
Pulling off
–Release securing clip -2- in direction of -arrow-.
–Disconnect washer fluid hoses -1-.
Fitting
Install in the reverse order of removal, observing the following: The securing clip must be heard to engage.
6.1.2Repairing smooth tube
thgirypocybdetcetorP
Repairs are carried out on smooth tubes with diameters of 5 mm and 6 mm and a hose thickness of 2 mm, using an EPDM tube ⇒ Electronic parts catalogue (ETKA).
Installing
–Cut out damaged section with straight cuts.
–Cut EPDM hose -2- to required length.
–Insert ends of smooth tube -1- 10 mm into EPDM hose -2-.
–Secure EPDM hose -2- with cable ties -3-.
6.1.3Repairing corrugated tube
Special tools and workshop equipment required
♦ Hot air blower -VAS 1978/14A-
♦ Shrink element for hot air blower -VAS 1978/15A-
Important
• Do not strain the repair point with tension or bending load.
• If the damaged section is longer than 20 mm, a new piece of corrugated tube must be installed ⇒ Electronic parts cata‐logue (ETKA), and the repair must be carried out twice.
Installing
–Cut out damaged section with straight cuts.
–Slide a 20 mm heat-shrink hose onto corrugated tube -1and -2-.
thgirypocybdetcetorP
–Using hot air blower -VAS 1978/14A- and shrink element for hot air blower -VAS 1978/15A-, apply heat to end of corruga‐ted tube -1-.
GAnegawskloVybthgirypoC.tnemuco
–Press coupling piece -3- ⇒ Electronic parts catalogue (ET‐KA) in direction of -arrow A- into corrugated tube -1-.
–Using hot air blower and shrink element for hot air blower, apply heat to end of corrugated tube -2-.
–Press coupling piece -4- ⇒ Electronic parts catalogue (ET‐KA) in direction of -arrow B- into corrugated tube -2-.
–Fit coupling pieces -3- and -4-.
–Secure end of corrugated tube -1- and -2- to hot air blower and shrink element through heat-shrink hose. ID.3 2020 ➤ Electrical system - Edition 08.2022
94
–Lights,
bulbs, switches - exterior
1Safety information and repair notes
1.1Safety information
Observe safety information ⇒ Safety information and repair notes; Rep. gr. 00; Safety information.
1.2Repair instructions
Observe repair instructions ⇒ Safety and repair instructions; Rep. gr. 00; Repair instructions.
ID.3 2020 ➤ Electrical system - Edition 08.2022
2Headlights
2.1Assembly overview - headlight, LED
2.1.1Assembly overview – headlight
Overview is shown for left side of vehicle as an example
. icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole,
1 - Front left headlight -MX1-/ front right headlight -MX2-
❑⇒ Rep. gr. 94; Remov‐ing and installing head‐light
❑⇒ Rep. gr. 94; Adjust‐ing headlights
2 - Front left turn signal bulbM5-/front right turn signal bulb -M7-
❑⇒ Rep. gr. 94; Remov‐ing and installing front turn signal bulb [M5]/ [M7]
3 - Grip for front turn signal bulb -M5-/-M7-
4 - Left headlight range con‐trol motor -V48-/right head‐light range control motorV49-
❑⇒ Rep. gr. 94; Remov‐ing and installing head‐light range control mo‐tor [V48]/[V49]
5 - Bolt
❑Qty. 4
❑1.5 Nm
6 - Housing cover for head‐light range control motor
thgirypocy . icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole, isnotpermittedunlessauthorisedbyV
❑To be used in event of repairs
7 - Seal
❑For housing cover
8 - Seal
9 - Speed nut
❑M 6
10 - Bolt
❑Qty. 4
❑4.5 Nm
11 - Output module 1 for left LED headlight -A31-/output module 1 for right LED headlight -A27-
❑⇒ Rep. gr. 94; Removing and installing output module 1 for LED headlight [A27]/[A31]
12 - Bolt
❑Qty. 3
❑1.5 Nm
2.2Assembly overview - headlight, LED matrix
2.2.1Assembly overview – headlight
Overview is shown for left side of vehicle as an example ID.3 2020 ➤ Electrical system - Edition 08.2022
1 - Front left headlight -MX1-/ front right headlight -MX2-
❑⇒ Rep. gr. 94; Remov‐ing and installing head‐light
❑⇒ Rep. gr. 94; Adjust‐ing headlights
2 - Mounting
❑For headlight range control motor
3 - Left headlight range con‐trol motor -V48-/right head‐light range control motorV49-
❑⇒ Rep. gr. 94; Remov‐ing and installing head‐light range control mo‐tor [V48]/[V49]
4 - Left headlight fan -V407-/ right headlight fan -V408-
❑⇒ Rep. gr. 94; Remov‐ing and installing head‐light fan [V407]/[V408]
5 - Bolt
❑Qty. 2
❑1.5 Nm
6 - Seal
7 - Bolt
❑To be used in event of repairs
❑Qty. 4
❑1.5 Nm
8 - Housing cover
❑To be used in event of repairs
9 - Bolt
❑To be used in event of repairs
❑Qty. 4
❑1.5 Nm
10 -
❑To be used in event of repairs
❑For headlight fan
11 - Seal
❑For housing cover
12 - Bolt
❑Qty. 3
❑1.5 Nm
13 - Seal
❑With front left turn signal bulb -M5-/front right turn signal bulb -M7ID.3 2020 ➤ Electrical system - Edition 08.2022
14 - Left LED module for daytime running light and side light -L176-/right LED module for daytime running light and side light -L177-
ID.3 2020 ➤ Electrical system - Edition 08.2022
❑⇒ Rep. gr. 94; Removing and installing LED module for daytime running light and side light [L176]/ [L177]
15 - Seal
❑For left LED module for daytime running light and side light [L176]/[L177]
16 - Speed nut
❑M 6
17 - Bolt
❑Qty. 4
❑4.5 Nm
18 - Output module 1 for left LED headlight -A31-/output module 1 for right LED headlight -A27-
❑⇒ Rep. gr. 94; Removing and installing output module 1 for LED headlight [A27]/[A31]
19 - Bolt
❑Qty. 3
❑1.5 Nm
2.3Assembly overview – repair kit for headlight housing
Overview is shown for left side of vehicle as an example
rup op s e s , i n p a r t o r in w hole,
Electrical system - Edition 08.2022
1 - Front left headlight -MX1-/ front right headlight -MX2-
❑⇒ Rep. gr. 94; Remov‐ing and installing head‐light
❑⇒ Rep. gr. 94; Adjust‐ing headlights
2 - Bolt
❑Qty. 2
❑1.5 Nm
3 - Upper retaining tab
❑⇒ Rep. gr. 94; Installing repair kit for headlight housing
4 - Bolt
❑Qty. 2
❑1.5 Nm
5 - Inner retaining tab
❑⇒ Rep. gr. 94; Installing repair kit for headlight housing
6 - Front retaining tab
❑⇒ Rep. gr. 94; Installing repair kit for headlight housing
7 - Bolt
❑Qty. 2
❑1.5 Nm
8 - Bolt
❑Qty. 2
❑1.5 Nm
9 - Rear retaining tab
❑⇒ Rep. gr. 94; Installing repair kit for headlight housing
10 - Bolt
❑Qty. 2
❑1.5 Nm
11 - Speed nut
❑M 6
12 - Outer retaining tab
❑⇒ Rep. gr. 94; Installing repair kit for headlight housing
2.4Removing and installing headlight
The control unit 2 for break-in protection -J1192- and control unit 3 for break-in protection -J1193- will henceforth be referred to as “control unit for break-in protection”.
The front left headlight -MX1- and front right headlight -MX2will henceforth be referred to as “headlight”.
Removing
–Remove bumper cover ⇒ General body repairs, exterior; Rep. gr. 63; Front bumper; Removing and installing bumper cover.
–Remove bracket for control unit for break-in protection ⇒ o6.3 verview ? control unit for break-in protection”, page 88
For headlight on driver side
–Pull off Bowden cable coupling from headlight ⇒ General body repairs, exterior; Rep. gr. 55; Bonnet; Removing and installing Bowden cable.
All vehicles (continued)
–Unscrew bolts -2-.
–Separate electrical connector -3-.
–Remove headlight -1-.
Installing
Install in the reverse order of removal, observing the following:
–Push headlight into guide mountings.
–Check headlight adjustment and adjust headlights ⇒ Mainte‐nance; Booklet ; Descriptions of work.
Tightening torques
♦ ⇒ Rep. gr. 94; Assembly overview – headlight
2.5Adjusting headlights
Adjust headlights ⇒ Maintenance; Booklet ; Headlight adjust‐ment: Checking LED headlight with matrix beam⇒ Maintenance; Booklet ; Headlight adjustment: Checking LED headlight. ID.3 2020
2.6Removing and installing front turn sig‐nal bulb [M5]/[M7], LED
2.6.1Removing and installing front turn sig‐nal bulb [M5]/[M7]
The front left turn signal bulb -M5- and front right turn signal bulb -M7- will henceforth be referred to as “turn signal bulb”.
Removal and installation are described for left-hand side of ve‐hicle as an example.
For a better view, the following work procedure is shown with the front left headlight -MX1- removed.
Removing NOTICE
Risk of damage to turn signal bulb.
– Do not touch the glass part of the turn signal bulb with bare fingers. Wear clean fabric gloves, for example, when removing and installing the turn signal bulb.
–Release grip with turn signal bulb -1- in direction of -arrow-.
–Pull turn signal bulb -2- out of grip -1-.
Installing
Install in reverse order of removal. ID.3 2020 ➤ Electrical system - Edition 08.2022
GAne
2.7Removing and installing front turn sig‐nal bulb [M5]/[M7], LED matrix
2.7.1Removing and installing front turn sig‐nal bulb [M5]/[M7]
The front left turn signal bulb -M5- and front right turn signal bulb -M7- will henceforth be referred to as “turn signal bulb”.
The left LED module for daytime running light and side light -L176- and right LED module for daytime running light and side light -L177- will henceforth be referred to as LED module for daytime running light.
Note
The front turn signal bulb and LED module for daytime running lights form a unit and cannot be removed separately.
–⇒ Rep. gr. 94; Removing and installing LED module for day‐time running light and side light [L176]/[L177].
2.8Installing repair kit for headlight hous‐ing
The front left headlight -MX1- and front right headlight -MX2will henceforth be referred to as “headlight”.
Note
Various headlight housing repair kits are available for the head‐light ⇒ Electronic parts catalogue (ETKA).
Removing
–Remove headlight with defective retaining tab ⇒ Rep. gr. 94; Removing and installing headlight.
–Remove remaining parts of defective retaining tab from headlight housing.
Installing
. icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole, isnotpermittedunlessauthorisedbyVolkswagen
–Fit retaining tab -1- of repair kit to headlight. –Tighten bolts -2-.
Electrical system - Edition 08.2022
Continue installation in reverse order of removal, observing the following:
–Install headlight and align it flush to body contour.
–Check headlight adjustment and adjust headlights ⇒ Mainte‐nance; Booklet ; Descriptions of work.
Tightening torques
♦ ⇒ Rep. gr. 94; Assembly overview – repair kit for headlight housing
2.9Removing and installing headlight range control motor [V48]/[V49]
2.9.1Removing and installing headlight range control motor [V48]/[V49]
Special tools and workshop equipment required
♦ ESD workplace VAS 6613 International -VAS 6613-
The front left headlight -MX1- and front right headlight -MX2will henceforth be referred to as “headlight”.
The left headlight range control motor -V48- and right headlight range control motor -V49- will henceforth be referred to as “con‐trol motor”.
Removal and installation are described for left-hand side of ve‐hicle as an example.
Removing
–Remove headlight ⇒ Rep. gr. 94; Removing and installing headlight.
NOTICE
Risk of damage to electrical components.
Electrostatic charge may damage electrical components.
– Work on electrical components must always be carried out at an ESD workplace.
–Place headlight onto ESD workplace -VAS 6613-.
. icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole, isnotpermittedunlessauthorisedbyVolkswagen AG Volkswagen
–Turn height adjustment screws at top of headlight to stop towards right.
–Use a hammer to carefully release housing cover -1- along predetermined break line -2-.
–Remove housing cover -1- from headlight.
–Release control motor -1-:
system - Edition 08.2022
♦ On left headlight, turn in direction of -arrow-.
♦ for right headlight, turn in opposite direction of -arrow-.
–Swing left headlight range control motor -2- downwards so that the ball head is pushed upwards out of ball head mount‐ing -3-.
–Pull control motor -2- towards rear out of headlight until elec‐trical connector -1- is accessible.
–Disconnect connector -1-.
–Remove control motor -2-.
Installing
Install in the reverse order of removal, observing the following:
–Pull ball head mounting towards rear.
–Engage ball head on control motor into ball head mounting in headlight.
NOTICE
Risk of destroying headlight due to ingress of water.
– When installing the housing covers -1-, make sure that the seal is correctly seated.
Note
la rup op s e s , i n p a r t o r in w hole,
A new housing cover -1- must be used only, if the repair is carried out for the first time.
–Fit housing cover -1- on headlight.
CLICK HERE TO DOWNLOAD THE COMPLETE MANUAL
• Thank you very much for reading the preview of the manual.
• You can download the complete manual from: www.heydownloads.com by clicking the link below
• Please note: If there is no response to CLICKING the link, please download this PDF first and then click on it.
CLICK HERE TO DOWNLOAD THE
ID.3
Electrical system - Edition 08.2022
–Tighten bolts -2-.
–Check headlight adjustment and adjust headlights ⇒ Mainte‐nance; Booklet ; Descriptions of work.
Tightening torques
♦ ⇒ Rep. gr. 94; Assembly overview – headlight
2.10Removing and installing headlight range control motor [V48]/[V49]
2.10.1Removing and installing headlight range control motor [V48]/[V49]
Special tools and workshop equipment required
♦ ESD workplace VAS 6613 International -VAS 6613-
The front left headlight -MX1- and front right headlight -MX2will henceforth be referred to as “headlight”.
The left headlight range control motor -V48- and right headlight range control motor -V49- will henceforth be referred to as “con‐trol motor”.
Removal and installation are described for left-hand side of ve‐hicle as an example.
Removing
–Remove headlight ⇒ Rep. gr. 94; Removing and installing headlight.
NOTICE
thgirypocybdetcetorP . icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole, isnotpermittedunlessauthorisedbyVolkswagen
Risk of damage to electrical components.
Electrostatic charge may damage electrical components.
– Work on electrical components must always be carried out at an ESD workplace.
–Place headlight onto ESD workplace -VAS 6613-.
Electrical system - Edition 08.2022
–Turn height adjustment screws of headlight to stop towards right.
–Use a hammer to carefully release housing cover -1- along predetermined break line -2-.
–Remove housing cover -1- from headlight.
–Release control motor -1-:
AGdoesnotguaranteeoraccep
♦ On left headlight, turn in direction of -arrow-.
thgirypocybdetcetorP . icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole, isnotpermittedunlessauthorisedbyVolkswagen
♦ for right headlight, turn in opposite direction of -arrow-.
–Swing left headlight range control motor -1- downwards so that the ball head is pushed upwards out of ball head mount‐ing -3-.
–Pull control motor -1- towards rear out of headlight until elec‐trical connector -2- is accessible.
–Disconnect connector -2-.
–Remove control motor -1-.
Electrical system - Edition 08.2022
Installing
Install in the reverse order of removal, observing the following:
–Pull ball head mounting towards rear.
–Engage ball head on control motor into ball head mounting in headlight.
NOTICE
Risk of destroying headlight due to ingress of water.
– When installing the housing cover -1-, make sure that the seal is correctly seated.
Note
A new housing cover -1- must be used only, if the repair is carried out for the first time.
–Fit housing cover -1- on headlight.
–Tighten bolts -2-.
–Check headlight adjustment and adjust headlights ⇒ Mainte‐nance; Booklet ; Descriptions of work.
Tightening torques
♦ ⇒ Rep. gr. 94; Assembly overview – headlight
2.11Removing and installing LED module for daytime running light and side light [L176]/[L177]
Special tools and workshop equipment required
♦ ESD workplace VAS 6613 International -VAS 6613-
♦ Torque screwdriver -V.A.G 1624-
The front left headlight -MX1- and front right headlight -MX2will henceforth be referred to as “headlight”.
The left LED module for daytime running light and side light -L176- and right LED module for daytime running light and side light -L177- will henceforth be referred to as LED module for daytime running light.
Removal and installation are described for the left vehicle side as an example.
Removing
–Remove headlight ⇒ Rep. gr. 94; Removing and installing headlight. ID.3 2020 ➤
2020 ➤ Electrical system - Edition 08.2022
NOTICE
Risk of damage to electrical components. Electrostatic charge may damage electrical components.
– Work on electrical components must always be carried out at an ESD workplace.
–Place headlight onto ESD workplace -VAS 6613-.
–Unscrew bolts -2-.
thgirypocybdetcetorP
–Guide LED module for daytime running light -1- out of head‐light housing until electrical connector is accessible.
–Disconnect electrical connector.
–Remove LED module for daytime running -1-.
Installing
Install in reverse order of removal, observing the following:
NOTICE
Risk of destroying headlight due to ingress of water.
– Check seal between LED module for daytime running and headlight for damage.
– Make sure seal is properly seated.
–Check headlight settings and adjust headlights if necessary ⇒ Maintenance; Booklet 53.1; Descriptions of work.
Tightening torques
♦ ⇒ Rep. gr. 94; Assembly overview – headlight
ID.3
Electrical system - Edition 08.2022
2.12Removing
and installing output mod‐
ule 1 for LED headlight [A27]/[A31]
Special tools and workshop equipment required
♦ ESD workplace VAS 6613 International -VAS 6613-
The front left headlight -MX1- and front right headlight -MX2will henceforth be referred to as “headlight”.
The output module 1 for left LED headlight -A31- and output module 1 for right LED headlight -A27- will henceforth be refer‐red to as “output module”.
Removal and installation are described for left-hand side of ve‐hicle as an example.
Removing
If the output module is renewed, perform the test plan for the renewal of the output module:
–Carry out function “Renew output module” using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00; Access to diagnoses.
Continued –Remove headlight ⇒ Rep. gr. 94; Removing and installing headlight.
NOTICE
Risk of damage to electrical components.
Electrostatic charge may damage electrical components.
– Work on electrical components must always be carried out at an ESD workplace.
–Place headlight onto ESD workplace -VAS 6613-.
–Unscrew bolts -2-. ID.3 2020 ➤
Electrical system - Edition 08.2022
–Pull output module -1- off headlight until electrical connector is accessible.
–Disconnect electrical connector.
–Remove output module -1-.
Installing
Install in the reverse order of removal, observing the following:
NOTICE
Risk of destroying headlight due to ingress of water.
– Check seal between output module and headlight for dam‐age.
– Ensure proper seating of seal.
–Check headlight adjustment and adjust headlights ⇒ Mainte‐nance; Booklet ; Descriptions of work.
Tightening torques
♦ ⇒ Rep. gr. 94; Assembly overview – headlight
2.13Removing and installing light conduc‐tor for contour lighting in radiator grille [L362]/[L363]
The light conductor for contour lighting in radiator grille, front left -L363-/light conductor for contour lighting in radiator grille, front right -L362- will henceforth be referred to as “light conductor”.
Removing
thgirypocybdetcetorP
–Remove front badge ⇒ General body repairs, exterior; Rep. gr. 66; Lettering and badges; Removing and installing front badge.
–Disconnect electrical connector -2-.
–Release retaining clips -3- in direction of -arrow A-.
–Pull out light conductor -1-.
Installing
Install in the reverse order of removal, observing the following:
ID.3 2020 ➤
Electrical system - Edition 08.2022
–The light conductor must be heard to engage.
2.14Removing and installing headlight fan [V407]/[V408]
Special tools and workshop equipment required
♦ ESD workplace VAS 6613 International -VAS 6613-
♦ Torque screwdriver -V.A.G 1624-
The front left headlight -MX1- and front right headlight -MX2will henceforth be referred to as “headlight”.
The left headlight fan -V407- and right headlight fan -V408- will henceforth be referred to as “headlight fan”.
Removal and installation are described for left-hand side of ve‐hicle as an example.
Removing –Remove headlight ⇒ Rep. gr. 94; Removing and installing headlight.
NOTICE
Risk of damage to electrical components.
Electrostatic charge may damage electrical components.
– Work on electrical components must always be carried out at an ESD workplace.
–Place headlight onto ESD workplace -VAS 6613-.
–Use a hammer to carefully release housing cover -2- along predetermined break line -1-.
–Remove housing cover -2- from headlight.
–Unscrew bolts -3-.
–Disconnect connector -2-.
–Remove fan -1-.
Installing
Install in the reverse order of removal, observing the following:
NOTICE
Risk of destroying headlight due to ingress of water.
– When installing the housing cover -1-, make sure that the seal is correctly seated.
Note
A new housing cover -1- must be used only, if the repair is carried out for the first time.
–Fit housing cover -1- on headlight.
isnotpermittedunlessauthorisedbyVolkswagen
Volkswagen AGdoesnot
–Tighten bolts -2-.
–Check headlight adjustment and adjust headlights ⇒ Mainte‐nance; Booklet ; Descriptions of work.
Tightening torques
♦ ⇒ Rep. gr. 94; Assembly overview – headlight
3Tail lights
3.1Assembly overview – tail light cluster in body
Overview is shown for left side of vehicle as an example
1 - Left tail light -MX3-/right tail light -MX4-
❑⇒ Rep. gr. 94; Re‐moving and installing tail light cluster [MX3]/ [MX4]
2 - Bolts
❑Tightening sequence and specified torque ⇒ page 74
3 - Lower tail light cluster trim
❑⇒ Rep. gr. 94; Re‐moving and installing tail light cluster [MX3]/ [MX4]
thgirypocybdetcet . icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole,
Body tail light clusters - specified torque and tightening se‐quence ID.3 2020 ➤ Electrical system - Edition 08.2022
Stage Component Specified torque
1. -1- and -2- Screw in by hand
2. -1- and -2- 3 Nm
3.2Assembly overview – tail light clusters in rear lid
Overview is shown for left side of vehicle as an example
1 - Trim for tail light
❑Engaged in rear lid
❑⇒ Rep. gr. 94; Remov‐ing and installing trim for tail light cluster
ID.3 2020 ➤
Electrical system - Edition 08.2022
3.3Removing and installing tail light clus‐ter [MX3]/[MX4]
Special tools and workshop equipment required
♦ Removal wedge -3409-
The left tail light cluster -MX3- and right tail light cluster -MX4will henceforth be referred to as “right tail light cluster”.
Removal and installation are described for left-hand side of ve‐hicle as an example.
Removing
–Unclip low tail light cluster trim -1- in direction of -arrow Awith removal wedge -3409-.
–Unscrew bolts -2-.
–Remove tail light cluster -1- in direction of -arrow A- enough to allow access to electrical connector.
–Disconnect electrical connector.
. icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole,
–Remove tail light cluster -1-.
Installing
Install in the reverse order of removal, observing the following:
Tightening torques
♦ ⇒ Rep. gr. 94; Assembly overview – tail light cluster in body
3.4Removing and installing rear fog light [X3]
The rear fog light -X3- will henceforth be referred to as “rear fog light”.
Removal and installation are described for left-hand side of ve‐hicle as an example.
Removing
thgirypocybdetcetorP . icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole, isnotpermittedunlessauthorisedbyVolkswagen AG. Volkswagen
–⇒ General body repairs, exterior; Rep. gr. 66; Wheel housing liner; Removing and installing rear wheel housing liner.
–Disconnect connector -3-.
–Release retaining clips -2- in direction of -arrow A-.
–Remove rear fog light -1-.
Installing
.GAnegawskloVybthgirypoC.tnemucodsihtninoitamrof
Install in the reverse order of removal, observing the following:
–The rear fog light must engage audibly.
3.5Removing and installing trim for tail light cluster
Removal and installation are described for left-hand side of ve‐hicle as an example.
Removing
–⇒ General body repairs, interior; Rep. gr. 70; Luggage com‐partment trims; Removing and installing lower rear lid trim.
–Release retaining clips -1- in direction of -arrow A-.
–Remove tail light cluster.
Installing
Install in the reverse order of removal, observing the following: –The tail light cluster must engage audibly. ID.3 2020
4LED module for charging socket
4.1Removing and installing LED module for charging socket 1 [L263]
Special tools and workshop equipment required
♦ Torque screwdriver -V.A.G 1624-
Removing
–Remove charging flap unit ⇒ General body repairs, exteri‐or; Rep. gr. 55; Charging flap unit; Removing and installing charging flap unit.
–Unscrew bolts -2-.
–Remove LED module for charging socket 1 -L263- -1-.
Installing
Install in reverse order of removal, observing the following: Tightening torques
♦ ⇒ General body repairs, exterior; Rep. gr. 55; Charging flap unit; Assembly overview – charging flap unit
GAnegawskloVybthgiry
CLICK HERE TO DOWNLOAD THE COMPLETE MANUAL
• Thank you very much for reading the preview of the manual.
• You can download the complete manual from: www.heydownloads.com by clicking the link below
• Please note: If there is no response to CLICKING the link, please download this PDF first and then click on it.
CLICK HERE TO DOWNLOAD THE
ID.3 2020 ➤
5High-level brake light
5.1Assembly overview ? high-level brake light
1 - Electrical connector for high-level brake light bulbM25-.
2 - High-level brake light bulb -M25-
❑⇒ Rep. gr. 94; Remov‐ing and installing highlevel brake light bulb [M25]
5.2Removing and installing high-level brake light bulb [M25]
The high-level brake light bulb -M25- will henceforth be referred to a “high-level brake light”.
Removing
–Remove spoiler trim⇒ General body repairs, exterior; Rep. gr. 66; Spoiler; Removing and installing spoiler trim
– Before using a lever, always mask off the components installed in visible areas using commercially available ad‐hesive tape.
–Use a commercially available plastic wedge to release highlevel brake light -1- from retaining clips -2-.
–Remove high-level brake light -1-.
Installing
Install in reverse order of removal, observing the following:
NOTICE
Risk of damage to high-level brake light from water ingress. – When installing high-level brake light, make sure seal is correctly seated.
–The high-level brake light must be heard to engage in rear spoiler trim.
isnotpermittedunlessauthorisedbyVolkswagen AG Volkswagen AGdoesnotguaranteeoracceptanyliabilitywi
. icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole,
ID.3 2020 ➤ Electrical system - Edition 08.2022
6Entry and start authorisation system
6.1Overview of fitting locations ? entry and start authorisation system
6.1.1Overview of fitting locations – entry and start authorisation system, lefthand drive vehicles
thgirypocybdetcetorP . icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole, isnotpermittedunlessauthorisedbyVolkswagen
.GAnegawskloVybthgirypoC.tnemucodsihtninoitamrof
1 - Immobiliser reader coilD2-
❑Depending on equip‐ment/version
❑⇒ Rep. gr. 94; Remov‐ing and installing immo‐biliser reader coil [D2]
2 - Starter button -E378-
❑⇒ Rep. gr. 96; Remov‐ing and installing starter button [E378]
3 - Control unit 5 for break-in protection -J1195-
❑⇒ Rep. gr. 94; Remov‐ing and installing con‐trol unit 4 for break-in protection [J1194]/con‐trol unit 5 for break-in protection [J1195]
4 - Control unit 4 for break-in protection -J1194-
❑⇒ Rep. gr. 94; Remov‐ing and installing con‐trol unit 4 for break-in protection [J1194]/con‐trol unit 5 for break-in protection [J1195]
thgi . icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole, isnotpermittedunlessauthoris
5 - Entry and start authorisa‐tion control unit -J518-
❑⇒ Rep. gr. 94; Remov‐ing and installing entry and start authorisation control unit [J518], lefthand drive vehicles
6 - Onboard supply control unit -J519-
dbyVolkswagen AG. Volkswagen AGdoesnotgua
❑⇒ Rep. gr. 97; Removing and installing onboard supply control unit [J519]
7 - Control unit 2 for break-in protection -J1192-
❑⇒ Rep. gr. 94; Removing and installing control unit 2 for break-in protection [J1192]/control unit 3 for break-in protection [J1193]
8 - Control unit 3 for break-in protection -J1193-
❑⇒ Rep. gr. 94; Removing and installing control unit 2 for break-in protection [J1192]/control unit 3 for break-in protection [J1193]
9 - Control unit for electronic steering column lock -J764-
❑Removing and installing ⇒ Running gear, axles, steering; Rep. gr. 48; Steering column; Removing and installing control unit for electronic steering column lock [J764]
6.1.2Overview of fitting locations – entry and start authorisation system, righthand drive vehicles
1 - Immobiliser reader coilD2-
❑Depending on equip‐ment/version
❑⇒ Rep. gr. 94; Remov‐ing and installing immo‐biliser reader coil [D2]
2 - Starter button -E378-
❑⇒ Rep. gr. 96; Remov‐ing and installing starter button [E378]
3 - Control unit 5 for break-in protection -J1195-
❑⇒ Rep. gr. 94; Remov‐ing and installing con‐trol unit 4 for break-in protection [J1194]/con‐trol unit 5 for break-in protection [J1195]
4 - Control unit 4 for break-in protection -J1194-
❑⇒ Rep. gr. 94; Remov‐ing and installing con‐trol unit 4 for break-in protection [J1194]/con‐trol unit 5 for break-in protection [J1195]
icremmocroetavirprofgniyla rup op s e s , i n p a r t o r in w hole, isnotpermittedunless
5 - Onboard supply control unit -J519-
❑⇒ Rep. gr. 97; Remov‐ing and installing on‐board supply control unit [J519], right-hand drive vehicles
6 - Entry and start authorisa‐tion control unit -J518-
❑⇒ Rep. gr. 94; Removing and installing entry and start authorisation control unit [J518], right-hand drive vehicles
7 - Control unit 2 for break-in protection -J1192-
❑⇒ Rep. gr. 94; Removing and installing control unit 2 for break-in protection [J1192]/control unit 3 for break-in protection [J1193]
8 - Control unit 3 for break-in protection -J1193-
❑⇒ Rep. gr. 94; Removing and installing control unit 2 for break-in protection [J1192]/control unit 3 for break-in protection [J1193]
9 - Control unit for electronic steering column lock -J764-
❑Removing and installing ⇒ Running gear, axles, steering; Rep. gr. 48; Steering column; Removing and installing control unit for electronic steering column lock [J764]
6.2Overview of fitting locations ? keyless entry system
6.2.1Overview of
1 - Front passenger exterior door handle -EX7-
❑with contact sensor for front left exterior door handle -G605-
❑⇒ General body re‐pairs, exterior; Rep. gr. 57; Door compo‐nents; Removing and installing door handle
2 - Interior aerial 1 for entry and start authorisation -R138-
❑⇒ Rep. gr. 94; Remov‐ing and installing interi‐or aerial 1 for entry and start system [R138]
3 - Driver exterior door handle -EX6-
❑with contact sensor for front right exterior door handle -G606-
❑⇒ General body re‐pairs, exterior; Rep. gr. 57; Door compo‐nents; Removing and installing door handle
4 - Entry and start authorisa‐tion control unit -J518-
❑⇒ Rep. gr. 94; Remov‐ing and installing entry and start authorisation control unit [J518], lefthand drive vehicles
6.2.2Overview of
ID.3 2020 ➤ Electrical system - Edition 08.2022
1 - Front passenger exterior door handle -EX7-
❑with contact sensor for front left exterior door handle -G605-
❑⇒ General body re‐pairs, exterior; Rep. gr. 57; Door compo‐nents; Removing and installing door handle
2 - Entry and start authorisa‐tion control unit -J518-
❑⇒ Rep. gr. 94; Remov‐ing and installing en‐try and start authorisa‐tion control unit [J518], right-hand drive vehi‐cles
3 - Interior aerial 1 for entry and start authorisation -R138-
❑⇒ Rep. gr. 94; Remov‐ing and installing interi‐or aerial 1 for entry and start system [R138]
4 - Driver exterior door handle -EX6-
❑with contact sensor for front right exterior door handle -G606-
❑⇒ General body re‐pairs, exterior; Rep. gr. 57; Door compo‐nents; Removing and installing door handle
thgirypo . icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole, isnotpermittedunlessauthorisedb
1 - Entry and start authorisa‐tion control unit -J518-
❑⇒ Rep. gr. 94; Remov‐ing and installing en‐try and start authorisa‐tion control unit [J518], right-hand drive vehi‐cles
2 - Luggage compartment aerial for entry and start sys‐tem -R137-
❑⇒ Rep. gr. 94; Remov‐ing and installing lug‐gage compartment aer‐ial for entry and start system [R137]
6.3Assembly overview ? control unit for break-in protection
The overview is shown for the left side of vehicle as an exam‐ple.
. icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole, isnotpermittedunle
1 - Bracket for control unit 2 for break-in protec‐tion -J1192-/control unit 3 for break-in protection -J1193-
2 - Control unit 2 for breakin protection -J1192-/control unit 3 for break-in protection -J1193-
❑ ⇒ a6.7 nd installing control unit 2 for breakin protection [J1192]/ control unit 3 for breakin protection [J1193]”, page 92
3 - Bolt
❑qty. 2
❑2 Nm
. croetavirprofgniypoC
6.4Removing and installing entry and start authorisation control unit [J518]
thgirypocybdetcetorP
6.4.1Removing and installing entry and start authorisation control unit [J518], lefthand drive vehicles
Entry and start authorization control unit -J518- will henceforth be referred to as “control unit”.
Removing
If the control unit is renewed, perform the test plan for the re‐newal of the entry and start authorisation control unit:
–Carry out function “Renew entry and start authorisation con‐trol unit” using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00; Access to diagnoses. ID.3
ID.3 2020 ➤
Electrical system - Edition 08.2022
Continued
–Remove footwell cover on driver side ⇒ General body re‐pairs, interior; Rep. gr. 68; Compartments/covers; Removing and installing footwell cover on driver side.
–Disconnect electrical connector -2-.
–Release locking lug -3-.
–Swing out control unit -1- in direction of -arrow A-.
Installing
Install in the reverse order of removal, observing the following:
–Control unit must be heard to engage.
Following the renewal of the control unit, conclude the test plan for the renewal of the entry and start authorisation control unit:
–Carry out function “Renew interface for entry and start sys‐tem” using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00; Access to diagnoses.
. icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole, isnotpermittedunlessauthorisedbyVolkswagen
6.4.2Removing and installing entry and start authorisation control unit [J518], righthand drive vehicles
Entry and start authorization control unit -J518- will henceforth be referred to as “control unit”.
Removing
If the control unit is renewed, perform the test plan for renewal of the control unit:
–Carry out function “Renew entry and start authorisation con‐trol unit” using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00; Access to diagnoses.
Continued –Remove footwell vent on driver side ⇒ Heating, air condition‐ing system; Rep. gr. 87; Air duct; Removing and installing footwell vent on driver side.
–Unscrew bolts -2-.
–Remove control unit -1- far enough for electrical connector to become accessible.
–Disconnect electrical connector -3-.
–Remove control unit -1-.
Installing
Install in the reverse order of removal, observing the following: If the control unit has been renewed, conclude the test plan for the renewal of control unit:
–Carry out function “Renew entry and start authorisation con‐trol unit” using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00; Access to diagnoses.
Continued
Tightening torques
Component Specified torque
Bolts for interface for entry and start system
icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole,
8 Nm
thgirypocybdetcetorP
6.5Removing and installing interior aer‐ial 1 for entry and start system [R138]
The interior aerial 1 for entry and start system -R138- will henceforth be referred to as “aerial”.
Removing
–Remove centre console insert ⇒ General body repairs, inte‐rior; Rep. gr. 68; Centre console; Removing and installing centre console insert .
–Release fastener -2-.
–Remove aerial -1-.
Electrical system - Edition 08.2022
Installing
Install in reverse order of removal.
6.6Removing and installing luggage com‐partment aerial for entry and start sys‐tem [R137]
Special tools and workshop equipment required
♦ Removal wedge set -VAS 895 015-
The luggage compartment aerial for entry and start system -R137- will henceforth be referred to as “aerial”.
Removing
–Remove lock carrier trim ⇒ General body repairs, interior; Rep. gr. 70; Luggage compartment trims; Removing and installing lock carrier trim.
–Use removal wedge set -VAS 895 015- to lever aerial -1- in direction of -arrow A- off pins.
–Disconnect electrical connector -2-.
Installing
Install in reverse order of removal.
6.7Removing and installing control unit 2 for break-in protection [J1192]/control unit 3 for break-in protection [J1193]
The control unit 2 for break-in protection -J1192- and control unit 3 for break-in protection -J1193- will henceforth be referred to as “control unit for break-in protection”.
Removal and installation are described for the left vehicle side as an example.
Removing
–Remove front wheel housing liner ⇒ General body repairs, exterior; Rep. gr. 66; Wheel housing liner; Removing and installing front wheel housing liner.
–Disconnect electrical connector -3-.
–Release locking lugs -2-.
–Remove control unit for break-in protection -1- in direction of -arrow-.
Installing
Tightening torques
AG. Volkswagen
system - Edition 08.2022
Install in reverse order of removal, observing the following:
♦ ⇒ General body repairs, exterior; Rep. gr. 66; Wheel housing liner; Assembly overview – front wheel housing liner
6.8Removing and installing control unit 4 for break-in protection [J1194]/control unit 5 for break-in protection [J1195]
AGdoesnotguaranteeoracceptanyliabilitywi
The control unit 4 for break-in protection -J1194- and control unit 5 for break-in protection -J1195- will henceforth be referred to as “control unit for break-in protection”.
Removal and installation are described for the left vehicle side as an example.
Removing
–Remove bumper cover ⇒ General body repairs, exterior; Rep. gr. 63; Rear bumper; Removing and installing bumper cover.
–Disconnect electrical connector -3-. ID.3 2020 ➤
. icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole, isnotpermittedunlessauthorisedbyVolkswagen
CLICK HERE TO DOWNLOAD THE COMPLETE MANUAL
• Thank you very much for reading the preview of the manual.
• You can download the complete manual from: www.heydownloads.com by clicking the link below
• Please note: If there is no response to CLICKING the link, please download this PDF first and then click on it.
CLICK HERE TO DOWNLOAD THE
–Release locking lugs -2-.
–Remove control unit for break-in protection -1- in direction of -arrow-.
Installing
Install in reverse order of removal, observing the following:
Tightening torques
♦ ⇒ General body repairs, exterior; Rep. gr. 63; Rear bumper; Assembly overview – rear bumper
6.9Removing and installing contact sen‐sor for front left exterior door handle [G605]
thgirypocybdetcetorP
The contact sensor for front left exterior door handle -G605- is installed in the driver exterior door handle -EX6- and cannot be removed individually.
Removing and installing driver exterior door handle -EX6⇒ General body repairs; Rep. gr. 57; Door components; Remov‐ing and installing exterior door handle [EX6]/[EX7].
6.10Removing and installing contact sen‐sor for front right exterior door handle [G606]
The contact sensor for front right exterior door handle -G606- is installed in the front passenger exterior door handle -EX7- and cannot be removed individually.
Removing and installing front passenger exterior door handle -EX7- ⇒ General body repairs; Rep. gr. 57; Door components; Removing and installing exterior door handle [EX6]/[EX7].
6.11Removing and installing entry and start authorisation aerial [R200]/[R201]
The left aerial for entry and start authorisation -R200- and right entry and start authorisation aerial -R201- will henceforth be referred to as “aerial”.
Removal and installation are described for the left vehicle side as an example.
Removing
–Remove front wheel housing liner ⇒ General body repairs, exterior; Rep. gr. 66; Wheel housing liner; Removing and installing front wheel housing liner.
–Disconnect electrical connector -1-.
–Release locking lugs -2- using an 8 mm socket.
–Remove aerial -3-.
Installing
Install in reverse order of removal, observing the following: Tightening torques
♦ ⇒ General body repairs, exterior; Rep. gr. 66; Wheel housing liner; Assembly overview – front wheel housing liner
4 - Steering column electron‐ics control unit -J527-
❑With windscreen wiper switch -E- with inter‐mittent wiper switchE22- with turn signal switch -E2- with head‐light dipper and flasher switch -E4- with elec‐tromechanical parking brake button -E538-
❑With airbag coil con‐nector and return ring with slip ring -F138with selector lever locked in position P switch -F319-
❑With selector lever po‐sition display -Y6-
❑Depending on equip‐ment/version with cruise control system switch -E45- with cruise control system (CCS) SET button -E227with multifunction dis‐play call-up buttonE86- with heated steer‐ing wheel -Z36-
❑⇒ Rep. gr. 94; Removing and installing steering column electronics control unit [J527]
5 - Control unit for electronic steering column lock -J764-
❑⇒ Running gear, axles, steering; Rep. gr. 48; Steering column; Removing and installing control unit for electronic steering column lock [J764]
6 - Bolt
❑2.5 Nm
7 - Steering column
❑⇒ Running gear, axles, steering; Rep. gr. 48; Steering column; Removing and installing steering column
Electrical system - Edition 08.2022
7.2Removing and installing steering col‐umn electronics control unit [J527]
The steering column electronics control unit -J527- will hence‐forth be referred to as “steering column electronics control unit”.
Removing
–Move steering wheel to rearmost and lowest position. Use the full range of the steering column adjustment for this pur‐pose.
–Remove lower steering column trim ⇒ General body repairs, interior; Rep. gr. 68; Compartments/covers; Removing and installing lower steering column trim.
–Remove control unit with display unit for driver information system -J1254- ⇒ Rep. gr. 90; Removing and installing control unit with display unit for driver information system [J1254].
NOTICE
Risk of damage to the electronic components due to electro‐static discharge.
thgirypocybdetcetorP . icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole, isnotpermittedunlessauthorisedbyVolkswagen AG Volkswagen
– Discharge any static electricity in body by briefly touching door striker plate.
–Separate electrical connector -2-.
–Unscrew bolts -3-.
NOTICE
Risk of damage to the return ring.
– When removed, the return ring with slip ring must not be turned.
–Pull off steering column electronics control unit -1-.
Installing
Install in the reverse order of removal, observing the following:
–Before pushing on steering column electronics control unit -3-, ensure the following:
Electrical system - Edition 08.2022
♦ The “arrows” -4- must align.
♦ Coil connector -2- must be visible in window -1-.
Tightening torques
Component Specified torque
Bolts for steering column elec‐tronics control unit 1.3 Nm
7.3Removing and installing immobiliser reader coil [D2]
The immobiliser reader coil -D2- will henceforth be referred to as reader coil.
Removing –Remove lower steering column trim ⇒ General body repairs, interior; Rep. gr. 68; Compartments/covers; Removing and installing lower steering column trim.
–Disengage locking device -2- in direction of -arrow A-.
thgirypocybdetcetorP . icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole,
–Pull out reader coil -1-.
Installing
Install in the reverse order of removal, observing the following:
Reader coil must be heard to engage.
ID.3 2020 ➤
8Automatic headlight range control
8.1Assembly overview - automatic headlight range control
The overview shows a left-hand drive vehicle as an example.
1 - Data bus diagnostic inter‐face -J533-
❑⇒ Rep. gr. 97; Remov‐ing and installing data bus diagnostic interface [J533]
2 - Rear left vehicle level sender -G76-
❑Right-hand drive vehi‐cles: on rear right spring control arm
❑⇒ Rep. gr. 94; Remov‐ing and installing head‐light range control mo‐tor [V48]/[V49]
4 - Right headlight range con‐trol motor -V49-
❑⇒ Rep. gr. 94; Remov‐ing and installing head‐light range control mo‐tor [V48]/[V49]
icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole, isnotpermittedunlessauthorisedbyVolksw
ID.3 2020 ➤
Electrical system - Edition 08.2022
9Towing bracket
9.1Assembly overview – socket, trailer detector control unit
1 - Trailer detector control unit -J345-
❑⇒ Rep. gr. 94; Remov‐ing and installing trail‐er detector control unit [J345]
2 - Spreader rivet
3 - Trailer socket -U10❑
9.2Removing and installing trailer detector control unit [J345]
The trailer detector control unit -J345- will henceforth be refer‐red to as trailer detector control unit.
Removing
If the trailer detector control unit is renewed, perform the test plan for the renewal of the trailer detector control unit: –Carry out function “Renew trailer detector control unit” using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00; Access to diagno‐ses.
thgirypocybdetcetorP . icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole, isnotpermittedunlessauthorised
–Remove left luggage compartment side trim ⇒ General body repairs, interior; Rep. gr. 70; Luggage compartment trims; Removing and installing luggage compartment side trim.
–Remove spreader rivet -2-.
–Remove trailer detector control unit -1-.
–Disconnect electrical connectors -3-.
Installing
Install in the reverse order of removal, observing the following:
If the trailer detector control unit has been renewed, conclude the test plan for the renewal of the trailer detector control unit:
–Carry out function “Renew trailer detector control unit” using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00; Access to diagno‐ses.
Continued
Tightening torques
♦ ⇒ Rep. gr. 94; Assembly overview – socket, trailer detector control unit
thgirypocybdetcetorP . icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole,
GAnegawskloVybthgirypoC.tnemucodsihtninoitamrof
ID.3
Electrical system - Edition 08.2022
10Additional exterior lights
10.1Removing and installing number plate light [X4]/[X5]
The left number plate light -X4- and right number plate light -X5will henceforth be referred to as “number plate light”.
Removing
–Use a suitable screwdriver to release number plate light -1in direction of -arrow A-.
–Remove number plate light -1- in direction of -arrow B- until electrical connector is accessible.
–Disconnect electrical connector -1-.
–Remove number plate light -2-.
Installing
. icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole,
Install in reverse order of removal.
10.2Assembly overview - lights in exterior mirror
Overview is shown for left side of vehicle as an example
system - Edition 08.2022
1 - Mirror cover
❑⇒ General body re‐pairs, exterior; Rep. gr. 66; Exterior mirrors; Removing and instal‐ling upper mirror cover
2 - Bolt
❑Qty. 2
❑0.8 Nm
3 - Driver side exterior mirror turn signal bulb -L131-/front passenger side exterior mirror turn signal bulb -L132-
❑⇒ Rep. gr. 94; Remov‐ing and installing exte‐rior mirror turn signal bulb [L131]/[L132]
4 - Bolt
❑Qty. 3
❑9 Nm
5 - Mirror frame
❑⇒ General body re‐pairs, exterior; Rep. gr. 66; Exterior mirrors; Removing and instal‐ling mirror frame
6 - Mirror glass
❑⇒ General body re‐pairs, exterior; Rep. gr. 66; Exterior mirrors; Removing and instal‐ling mirror glass
7 - Bolt
❑Qty. 2
❑0.8 Nm
girypocybdetcetorP
GAnegawskloVybthg
8 - Driver side entry light in exterior mirror -W52-/front passenger side entry light in exterior mirror -W53-
❑Depending on equipment/installation period
❑⇒ Rep. gr. 94; Removing and installing entry light in exterior mirror [W52]/[W53]
9 - Bolt
❑0.8 Nm
10 - Mirror adjustment unit
❑⇒ General body repairs, exterior; Rep. gr. 66; Exterior mirrors; Removing and installing mirror adjust‐ment unit
11 - Bolt
❑0.8 Nm
12 - Exterior mirror
❑With driver side exterior mirror -VX4- and passenger side exterior mirror -VX5-
❑⇒ General body repairs, exterior; Rep. gr. 66; Exterior mirrors; Removing and installing exterior mirror
Electrical system - Edition 08.2022
10.3Removing and installing exterior mirror turn signal bulb [L131]/[L132]
The driver side exterior mirror turn signal bulb -L131- and front passenger side exterior mirror turn signal bulb -L132- will henceforth be referred to as “exterior mirror turn signal”.
Removing
Removal and installation are described for left-hand side of ve‐hicle as an example.
–⇒ General body repairs, exterior; Rep. gr. 66; Exterior mir‐rors; Removing and installing mirror cover
la rup op s e s , i n p a r t o r in w hole,
–Disconnect connector -3-.
–Unscrew bolts -2-.
–Remove turn signal -1-.
Installing
Install in the reverse order of removal, observing the following:
Tightening torques
♦ ⇒ Rep. gr. 94; Assembly overview - lights in exterior mirror
10.4Removing and installing entry light in exterior mirror [W52]/[W53]
The entry light in exterior mirror, driver side -W52- and entry light in exterior mirror, passenger side -W53- will henceforth be referred to as “entry light in exterior mirror”.
Removal and installation are described for left-hand side of ve‐hicle as an example.
Removing
–Remove turn signal ⇒ Rep. gr. 94; Removing and installing exterior mirror turn signal bulb [L131]/[L132].
–Unscrew bolt -2-. ID.3 2020 ➤
AG Volkswagen
–Guide out entry light in exterior mirror -3- until electrical con‐nector is accessible.
–Disconnect connector -1-.
Installing
Install in the reverse order of removal, observing the following:
Tightening torques
♦ ⇒ Rep. gr. 94; Assembly overview - lights in exterior mirror
10.5Assembly overview – lights in exterior door handle
. icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole,
1 - Mounting bracket
❑⇒ General body re‐pairs, exterior; Rep. gr. 57; Door compo‐nents; Removing and installing exterior door handle
2 - Bulb for exterior door han‐dle lighting
❑Light for exterior door handle illumination, driver side -L283-
❑Light for exterior door handle illumination, front passenger sideL284-
le, isnotpermittedunlessauthorisedbyVolksw
❑Light for rear exteri‐or door handle illumina‐tion, driver side -L285-
❑Light for rear exteri‐or door handle illumina‐tion, passenger sideL286-
❑⇒ Rep. gr. 94; Remov‐ing and installing bulb for exterior door handle illumination
3 - Contact sensor for exterior door handle
❑Contact sensor for front left exterior door handle -G605-
❑Contact sensor for front right exterior door han‐dle -G606-
❑⇒ Rep. gr. 94; Over‐view of fitting locations – keyless entry system
4 - Door handle trim
❑⇒ ; Rep. gr. ; Assembly overview – door handle
10.6Removing and installing bulb for exteri‐or door handle illumination
The light for exterior door handle illumination, driver side -L283-, light for exterior door handle illumination, front passenger sideL284-, light for rear exterior door handle illumination, driver side -L285- and light for rear exterior door handle, front passenger side -L286- will henceforth be referred to as light for exterior door handle illumination.
Note
Removal and installation are described for the driver side as an example.
Removing
–Remove door handle trim ⇒ General body repairs, exterior; Rep. gr. 58; Door components; Assembly overview – door handle and door lock. ID.3 2020 ➤ Electrical system - Edition 08.2022
–Disconnect connector -3-.
–Release locking device -2-.
–Remove electrical connector -1-.
–Remove bulb for exterior door handle illumination -4-.
Installing
Install in reverse order of removal.
thgirypocybdetcetorP . icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole, isnotpermittedunlessauthorisedbyVolkswagen
ID.3 2020 ➤ Electrical system - Edition 08.2022
CLICK HERE TO DOWNLOAD THE COMPLETE MANUAL
• Thank you very much for reading the preview of the manual.
• You can download the complete manual from: www.heydownloads.com by clicking the link below
• Please note: If there is no response to CLICKING the link, please download this PDF first and then click on it.
CLICK HERE TO DOWNLOAD THE
96 –Lights, bulbs, switches - interior
1Safety information and repair notes
1.1Safety information
Observe safety information ⇒ Safety information and repair notes; Rep. gr. 00; Safety information.
1.2Repair instructions
Observe repair instructions ⇒ Safety and repair instructions; Rep. gr. 00; Repair instructions.
2Lights
2.1Overview of fitting locations – lights in dash panel
The overview shows a left-hand drive vehicle as an example.
1 - Dynamic light strip 1 for information in dash panelL385-
❑⇒ Rep. gr. 96; Re‐moving and installing dynamic light strip 1 for information in dash panel [L385]
2 - Contour lighting of dash panel
❑With light 3 for dash panel contour lightingL245-
❑With light 2 for dash panel contour lightingL244-
❑⇒ Rep. gr. 96; Remov‐ing and installing light 2 for dash panel contour lighting [L244]/[L245], front passenger side
3 - Right footwell light -W10-
❑⇒ Rep. gr. 96; Remov‐ing and installing right footwell light [W10]
4 - Left footwell light -W9-
❑⇒ Rep. gr. 96; Remov‐ing and installing left footwell light [W9]
thgiryp . icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole, isnotpermittedunlessauthorised AG Volkswage A
5 - Light 1 for dash panel con‐tour lighting -L243-
❑⇒ Rep. gr. 96; Remov‐ing and installing light 1 for dash panel contour lighting [L243], driver side
2.2Overview of fitting locations - lights in front doors
The overview shows a left-hand drive vehicle as an example.
system - Edition 08.2022
1 - Light for front left door contour lighting -L251-/light for front right door contour lighting -L252-
❑⇒ General body re‐pairs, interior; Rep. gr. 70; Front door trims; Removing and instal‐ling front door trim
2 - Light 2 for front left door contour lighting -L296-/light 2 for front right door contour lighting -L297-
❑⇒ General body re‐pairs, interior; Rep. gr. 70; Front door trims; Removing and instal‐ling front door trim
3 - Central locking SAFE‐LOCK function warning lamp -K133-
r in w hole, isnotpermittedunlessauthorisedbyVolkswa
❑⇒ Rep. gr. 96; Remov‐ing and installing cen‐tral locking SAFELOCK function warning lamp [K133]
icremmocroetavirprofgniypoC
thgirypocybdetcetorP
GAnegawskl
2.3Overview of fitting locations – lights in luggage compartment
1 - Luggage compartment light -W3-
❑⇒ Rep. gr. 96; Remov‐ing and installing lug‐gage compartment light [W3]
2.4Overview of fitting locations - lights in centre console
ID.3 2020 ➤
Electrical system - Edition 08.2022
1 - Light 1 for front centre console background lightingL193-
❑⇒ Rep. gr. 96; Remov‐ing and installing light 1 for front centre con‐sole background light‐ing [L193]
2 - Electrical connector
thgir .
2.5Overview of fitting locations – lights in roof trim
The overview shows a left-hand drive vehicle as an example
1 - Rear left illuminated vanity mirror -W49-
❑⇒ Rep. gr. 96; Remov‐ing and installing rear il‐luminated vanity mirror [W49]/[W50]
2 - Front roof module -WX3-
❑With front passenger airbag warning lampK145-
❑With front left reading light -W65-
❑With front right reading light -W66-
❑With button illumination bulb -L76-
❑Can only be renewed together with front roof module -WX3-
❑⇒ Rep. gr. 96; Remov‐ing and installing front roof module [WX3]
3 - Rear interior light -WX2-
❑With rear left reading light -W11-
❑With rear right reading light -W12-
❑Can only be renewed together with rear interi‐or light -WX2-
❑⇒ Rep. gr. 96; Remov‐ing and installing rear interior light [WX2]
4 - Rear right illuminated vani‐ty mirror -W50-
edbyVolkswagen AG Volkswagen AGdoesnotguara
❑⇒ Rep. gr. 96; Removing and installing rear illuminated vanity mirror [W49]/[W50]
2.6Removing and installing footwell light [K268]/[K269]
2.6.1Removing and installing front left foot‐well light [K268]
Removing NOTICE
Risk of damage to component surfaces.
– Before using a lever, always mask off the components installed in visible areas using commercially available ad‐hesive tape.
–Disengage locking device -2- in direction of -arrow A-.
–Swing out front left footwell light -K268- -1-.
–Disconnect electrical connector -3-.
Installing
Install in reverse order of removal.
2.6.2Removing and installing right footwell light [K269]
Removing NOTICE
Risk of damage to component surfaces.
– Before using a lever, always mask off the components installed in visible areas using commercially available ad‐hesive tape.
–Disengage locking device -2- in direction of -arrow A-.
–Swing out front right footwell light -K269- -1-.
–Disconnect electrical connector -1-.
Installing
Install in reverse order of removal.
2.7Removing and installing central lock‐ing SAFELOCK function warning lamp [K133]
Removing
–Remove front door trim ⇒ General body repairs interior; Rep. gr. 70; Front door trims; Removing and installing front door trim. ID.3 2020 ➤ Electrical system - Edition 08.2022
–Release retaining lugs -arrows-.
–Pull central locking SAFELOCK function warning lampK133- -2- out of mounting -1-.
Installing
Install in reverse order of removal.
2.8Removing and installing luggage com‐partment light [W3]
Removing NOTICE
Risk of damage to component surfaces.
– Before using a lever, always mask off the components installed in visible areas using commercially available ad‐hesive tape.
thgirypocybdetcetorP . icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole,
–Release retaining hooks in -direction of arrow A-.
GAnegawskloVybthgirypoC.tnemucodsihtninoitamrof
–Swing out luggage compartment light -W3- -2-.
–Disconnect connector -1-.
Installing
Install in reverse order of removal.
ID.3 2020 ➤
Electrical system - Edition 08.2022
2.9Removing and installing rear illumina‐ted vanity mirror [W49]/[W50]
Rear left illuminated vanity mirror -W49- and rear right illumina‐ted vanity mirror -W50- will henceforth be referred to as “illumi‐nated vanity mirror”.
Removal and installation are described for the left vehicle side as an example.
Removing –Swing sun visor towards front.
NOTICE
Risk of damage to component surfaces.
– Before using a lever, always mask off the components installed in visible areas using commercially available ad‐hesive tape.
–Use a commercially available plastic wedge to lever out illu‐minated vanity mirror -1- at recess -arrow-.
–Disconnect electrical connector.
Installing
Install in reverse order of removal.
le, isnotpermittedunlessauthorisedbyVolkswagen
2.10Removing and installing dynamic light strip 1 for information in dash panel [L385]
Special tools and workshop equipment required
♦ Hooks -T10538-
The dynamic light strip 1 for information in dash panel -L385will henceforth be referred to as “dynamic light strip”.
Removing
–Remove A-pillar trims ⇒ General body repairs, interior; Rep. gr. 70; Trims, interior; Removing and installing upper A-pillar trim.
–Remove cover for dash panel/head-up display ⇒ General body repairs, interior; Rep. gr. 70; Removing and installing cover for dash panel/head-up display.
–Use hook -T10538--A- to unhook dynamic light strip -1- on left side in direction of -arrow-.
–Secure dynamic light strip -1- to prevent it from engaging again.
–Use hook -T10538--A- to unhook dynamic light strip -1- on right side in direction of -arrow-.
–Disconnect electrical connector.
–Remove dynamic light strip -1-.
Installing
Install in the reverse order of removal, observing the following:
–The dynamic light strip must be heard to engage.
2.11Removing and installing light 1 for front centre console background light‐ing [L193]
The light 1 for centre console background lighting -L193- will henceforth be referred to as “centre console background light‐ing”.
Removing
–Remove centre console insert ⇒ General body repairs, inte‐rior; Rep. gr. 68; Centre console; Removing and installing centre console insert .
–Release locking device -1-.
. icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole,
Electrical system - Edition 08.2022
–Remove centre console ambient lighting -2-.
–Disconnect electrical connector.
Installing
Install in reverse order of removal.
2.12Removing and installing light for dash panel contour lighting
isnotpermittedunlessauthorisedbyVolkswagen
2.12.1Removing and installing light 1 for dash panel contour lighting [L243], driver side
The light 1 for dash panel contour lighting -L243- will henceforth be referred to as contour lighting.
The removal procedure is shown for a left-hand drive vehicle as an example.
Removing
–Remove dash panel end cover on driver side ⇒ General body repairs, interior; Rep. gr. 70; Dash panel; Removing and installing dash panel end cover.
–Disconnect connector -2-.
thgirypocybdetcetorP . icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole,
–Release locking device -3-.
–Remove contour lighting -1-.
Installing
Install in reverse order of removal.
2.12.2Removing and installing light 2 for dash panel contour lighting [L244]/ [L245], front passenger side
The light 2 for dash panel contour lighting -L244-/light 3 for dash panel contour lighting -L245- will henceforth be referred to as contour lighting.
Volkswagen
The removal procedure is shown for a left-hand drive vehicle as an example.
Removing
icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole, isnotpermittedunlessauthorisedbyVolkswagen
–Remove dash panel trim on front passenger side ⇒ General body repairs, interior; Rep. gr. 70; Dash panel; Removing and installing dash panel end cover.
–Disconnect connector -3-.
ID.3 2020 ➤
Electrical system - Edition 08.2022
–Release locking device -2-.
–Remove contour lighting -1-.
Installing
Install in reverse order of removal.
thgirypocybdetcetorP . icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole,
GAnegawskloVybthgirypoC.tnemucodsihtninoitamrof
Electrical system - Edition 08.2022
3Controls
3.1Overview of fitting locations – controls in dash panel The overview shows a left-hand drive vehicle as an example.
thgirypocybdetcetorP . icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole, isnotpermittedunlessauthorisedbyVolkswagen
.GAnegawskloVybthgirypoC.tnemucodsihtninoitamrof
CLICK HERE TO DOWNLOAD THE COMPLETE MANUAL
• Thank you very much for reading the preview of the manual.
• You can download the complete manual from: www.heydownloads.com by clicking the link below
• Please note: If there is no response to CLICKING the link, please download this PDF first and then click on it.
CLICK HERE TO DOWNLOAD THE
1 - Operating unit for lighting -EX59-
❑With light switch -E1and button for auto‐matic lighting controlE854-
❑With button for dip‐ped beam headlightsE856- and button for side lights -E855-
❑With rear fog light but‐ton -E314- and rear fog light warning lamp -K13-
❑With switch and instru‐ment illumination regu‐lator -E20- and defrost‐er button -E782-
❑With front interior light button -E326-, rear interior light buttonE327-
la rup op s e s , i n p a r t o r in w hole, isnotpermittedunlessauthorisedbyVolkswagen
❑With front left read‐ing light button -E633-, front right reading light button -E634-
❑Depending on equip‐ment/version, can on‐ly be renewed along with front roof module -WX3-
❑⇒ Rep. gr. 96; Remov‐ing and installing front roof module [WX3]
2 - Rear interior light -WX2-
❑With rear left reading light -W11-
❑With rear right reading light -W12-
❑With rear left reading light button -E454-
❑With rear right reading light button -E455-
❑Can only be renewed together with rear interior light -WX2-
❑⇒ Rep. gr. 96; Removing and installing rear interior light/reading light
3 - Sun visors
❑With rear left vanity mirror contact switch -F298-/rear right vanity mirror contact switch -F299-
❑⇒ General body repairs, interior; Rep. gr. 68; Equipment; Removing and installing sun visor
3.6Removing and installing operating unit for lighting [EX59]
3.6.1Removing and installing operating unit for lighting [EX59], left-hand drive vehi‐cles
Special tools and workshop equipment required
♦ Hooks -T10538-
The operating unit for lighting -EX59- will henceforth be referred to as “operating unit for lighting”.
ID.3 2020 ➤ Electrical system - Edition 08.2022
Important
• The operating unit for lighting cannot be renewed without being damaged.
Removing
–Mark -2- centre of operating unit for lighting -1- according to dimension -a- and -b-.
♦ a = 26 mm
♦ b = 42 mm
CAUTION
Risk of hands and eyes being injured by glass splinters. When removing damaged components, glass splinters may enter eyes and flesh wounds may occur.
– Wear safety goggles.
– Wear protective gloves.
NOTICE
Danger of damage to components.
NOTICE
Risk of air duct being damaged.
– Mark 30 mm for plunge depth of drill bit.
AGdoesnotguaranteeoracceptanyliabilitywi
– Protect dash panel and dash panel vent from swarf.
–Use a commercially available 8 mm drill bit to drill 30 mm into operating unit for lighting -1- at marking -2-.
–Guide hook -T10538- -A- through hole.
. icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole, isnotpermittedunlessauthorisedbyVolkswagen AG Volkswagen
ID.3 2020 ➤
Electrical system - Edition 08.2022
–Engage hook -T10538- -A- in operating unit for lighting -1-.
–Pull out operating unit for lighting -1- in direction of -arrowuntil electrical connector is accessible.
–Disconnect electrical connector.
–Remove operating unit for lighting -1-.
Installing
Install in the reverse order of removal, observing the following: Important
• The operating unit for lighting must be heard to engage.
• Perform functional check.
3.6.2Removing and installing operating unit for lighting [EX59], right-hand drive ve‐hicles
Special tools and workshop equipment required
♦ Hooks -T10538-
The operating unit for lighting -EX59- will henceforth be referred to as “operating unit for lighting”.
Important
• The operating unit for lighting cannot be renewed without being damaged.
Removing –Mark -2- centre of operating unit for lighting -1- according to dimension -a- and -b-.
♦ a = 26 mm
♦ b = 42 mm
CAUTION
Risk of hands and eyes being injured by glass splinters. When removing damaged components, glass splinters may enter eyes and flesh wounds may occur.
– Wear safety goggles.
– Wear protective gloves.
NOTICE
Danger of damage to components.
– Protect dash panel and dash panel vent from swarf.
NOTICE
Risk of air duct being damaged.
– Mark 30 mm for plunge depth of drill bit.
–Use a commercially available 8 mm drill bit to drill 30 mm into operating unit for lighting -1- at marking -2-.
–Guide hook -T10538- -A- through hole.
–Engage hook -T10538- -A- in operating unit for lighting -1-.
–Pull out operating unit for lighting -1- in direction of -arrowuntil electrical connector is accessible.
–Disconnect electrical connector.
–Remove operating unit for lighting -1-.
Installing
Install in the reverse order of removal, observing the following:
Important
• The operating unit for lighting must be heard to engage.
• Perform functional check.
3.7Removing and installing centre switch module in dash panel [EX22]
The centre switch module in dash panel -EX22- will henceforth be referred to as “switch module in dash panel”.
Removing
–Remove control unit for front display and information con‐trol panel -J685- ⇒ Communication; Rep. gr. 91; Compo‐nents/control units; Removing and installing control unit for front display and information control panel [J685].
–Release retaining hooks -1-. ID.3
Electrical system - Edition 08.2022
–Remove switch module in dash panel -2-. Installing
Install in the reverse order of removal, observing the following: Important
• The switch module in dash panel must be heard to engage.
3.8Removing and installing operating unit for window regulator in driver door [EX36]
The operating unit for window regulator in driver door -EX36will henceforth be referred to as “window regulator operating unit”.
Removal and installation are described for a left-hand drive vehicle as an example.
Removing
–Remove trim for button ⇒ General body repairs, interior; Rep. gr. 70; Front door trims; Removing and installing trim for button.
–Release retaining hooks -2-.
–Remove window regulator operating unit -1- in direction of -arrow-. ID.3 2020 ➤ Electrical system - Edition 08.2022
system - Edition 08.2022
Installing
Install in the reverse order of removal, observing the following: Important
• The window regulator operating unit must be heard to en‐gage.
3.9Removing and installing window regu‐lator switch in front passenger door [EX27]
Window regulator switch in front passenger door -EX27- will henceforth be referred to as “window regulator switch”.
Removal and installation are described for a left-hand drive vehicle as an example.
Removing
–Remove switch trim ⇒ General body repairs, interior; Rep. gr. 70; Front door trims; Removing and installing button trim.
–Release locking devices -2-.
thgirypocybdetcetorP . icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole, isnotpermittedunlessauthorisedbyVolkswagen AG. Volkswagen
.GAnegawsk
–Remove window regulator switch -1- in direction of -arrow-.
Installing
Install in the reverse order of removal, observing the following: Important
• Window regulator switch must engage audibly.
3.10Removing and installing operating unit in rear door, driver side/passenger side [EX60]/[EX61]
Operating unit in rear door, driver side -EX61-/operating unit in rear door, passenger side -EX60- will henceforth be referred to as “operating unit”.
Removal and installation are described for the left vehicle side as an example.
2020 ➤ Electrical system - Edition 08.2022
Removing
–Remove trim for button ⇒ General body repairs, interior; Rep. gr. 70; Rear door trims; Removing and installing trim for button.
–Release fasteners -2-.
–Remove operating unit -1- in direction of -arrow-.
Installing
Install in the reverse order of removal, observing the following: Important
• Operating unit must engage audibly.
3.11Removing and installing starter button [E378]
The starter button -E378- will henceforth be referred to as “start‐er button”.
Removing
–Remove lower steering column trim ⇒ General body repairs, interior; Rep. gr. 68; Compartments/covers; Removing and installing lower steering column trim.
–Press together retaining clips -2-.
rup op s e s , i n p a r t o r in w hole,
Electrical system - Edition 08.2022
–Remove starter button -1-.
Installing
thgirypocybdetcetorP . icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole, isnotpermittedunlessauthorisedbyVolkswagen
Install in the reverse order of removal, observing the following: Important
• The starter button must be heard to engage.
3.12Removing and installing front roof module [WX3]
Front roof module -WX3- will henceforth be referred to as “roof module”.
Removing NOTICE
Risk of damage to component surfaces. – Before using a lever, always mask off the components installed in visible areas using commercially available ad‐hesive tape.
–Using commercially available plastic wedge, lever out roof module -1- in rear area in direction of -arrow A-.
GAnegawskloVybthgirypoC.tnemucodsihtninoitamrof
–Disconnect electrical connectors.
–Remove roof module -1- in direction of -arrow B-.
ID.3 2020 ➤
Electrical system - Edition 08.2022
Installing
Install in the reverse order of removal, observing the following: Important
• Roof module must be heard to engage.
3.13Removing and installing rear interior light [WX2]
The rear interior light -WX2- will henceforth be referred to as “rear interior light”.
Removing NOTICE
Risk of damage to component surfaces.
– Before using a lever, always mask off the components installed in visible areas using commercially available ad‐hesive tape.
–Use commercially available plastic wedge to lever out rear interior light -1- in rear area in direction of -arrow-.
–Remove rear interior light -1- until electrical connector is accessible.
–Disconnect electrical connector.
–Remove rear interior light -1-.
Installing
Install in the reverse order of removal, observing the following:
Important
• The rear interior light must be heard to engage. ID.3 2020 ➤
4Anti-theft alarm system
4.1Assembly overview – interior monitor
1 - Alarm horn -H12-
❑⇒ Rep. gr. 96; Remov‐ing and installing alarm horn [H12]
2 - Bracket for alarm hornH12-
3 - Shear nut
❑Renew after removing
4 - Anti-theft alarm sensorG578-
❑⇒ Rep. gr. 96; Remov‐ing and installing an‐ti-theft alarm sensor [G578]
5 - On-board supply control unit -J519-
❑ ⇒ a3.3 nd installing onboard supply control unit [J519]”, page 155
thgiry . icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole, isnotpermittedunlessauthorised
GAnegawsk
4.2Removing and installing alarm horn [H12]
The alarm horn -H12- will henceforth be referred to as “alarm horn”.
Removing
–Remove plenum chamber cover ⇒ General body repairs, exterior; Rep. gr. 50; Bulkhead; Removing and installing ple‐num chamber cover.
Note
The shear nut cannot be removed without being damaged. –Loosen shear nut -3- using suitable workshop equipment. ID.3 2020 ➤ Electrical system - Edition 08.2022
CLICK HERE TO DOWNLOAD THE COMPLETE MANUAL
• Thank you very much for reading the preview of the manual.
• You can download the complete manual from: www.heydownloads.com by clicking the link below
• Please note: If there is no response to CLICKING the link, please download this PDF first and then click on it.
CLICK HERE TO DOWNLOAD THE
Electrical system - Edition 08.2022
–Remove alarm horn -2- from plenum chamber.
–Disconnect connector -1-.
Installing
Install in the reverse order of removal, observing the following:
–Tighten new shear nut until head shears off.
Tightening torques
♦ ⇒ Rep. gr. 96; Assembly overview – interior monitor
4.3Removing and installing anti-theft alarm sensor [G578]
The anti-theft alarm sensor -G578- will henceforth be referred to as “anti-theft alarm sensor”.
Removing
The front interior light -WX1- will henceforth be referred to as “front interior light”.
–Remove front interior light ⇒ Rep. gr. 96; Removing and installing front interior light [WX1].
–Release retaining tabs -2- in direction of -arrow A-.
–Disengage locking device -2- in direction of -arrow A-. ID.3 2020 ➤
thgirypocybdetcetorP . icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole, isnotpermittedunlessauthorisedbyVolkswagen AG Volkswagen
–Remove individual sensors -1- from front interior light.
–Remove anti-theft alarm sensor -1-.
Installing
thgirypocybdetcetorP . icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole, isnotpermittedunlessauthorisedbyVolkswagen AG Volkswagen
Install in the reverse order of removal, observing the following: If the anti-theft alarm sensor has been renewed:
–Carry out function “Parametrise anti-theft alarm sensor” us‐ing ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00; Access to diagnoses. ID.3 2020 ➤ Electrical system - Edition 08.2022
th respect t o t h e c o r r e c t n e ss o f ni
.GAnegawskloVybthgirypoC.tnemucodsihtninoitamrof
- Edition 08.2022
5Cigarette lighter, socket
5.1Removing and installing 12 V socket [U5/U19]
Special tools and workshop equipment required
♦ Extracting tool -T4014812 V socket -U5- and 12 V socket 3 -U19- are referred to hereafter as 12 V socket.
The 12 V socket without illumination cannot be removed without being damaged.
Removing
For a better view, the following work procedure is shown with the 12 V socket removed.
NOTICE
Risk of damage to component surfaces.
– Mask off component in visible area using commercially available adhesive tape.
–Insert puller -T40148- -A- into 12 V socket -1-.
AGdoesnotguaranteeoracceptan
–Turn knurled nut -4- until locking device -3- engages in re‐cesses -2-.
–Pull out 12 V socket -1- with puller -T40148- -A-.
–Disconnect electrical connector.
–Loosen knurled nut and pull out puller -T40148- -A- from 12 V socket -1-.
Installing
Install in reverse order of removal.
. icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole,
1Safety information and repair notes
1.1Safety information
Observe safety information ⇒ Safety information and repair notes; Rep. gr. 00; Safety information.
1.2Repair instructions
Observe repair instructions ⇒ Safety and repair instructions; Rep. gr. 00; Repair instructions.
icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole,
2Relay carriers, fuse holders, elec‐tronics boxes
2.1Overview of fitting locations ? relay carriers, fuse holders, E-boxes
2.6.1Removing and installing fuse holder C [SC], left-hand drive vehicles
The fuse holder C -SC- will henceforth be referred to as “fuse holder C”.
Removing
–Disconnect battery ⇒ Rep. gr. 27; Disconnecting and con‐necting battery A.
–Remove dash panel ⇒ General body repairs, interior; Rep. gr. 70; Dash panel; Removing and installing dash panel.
–Release locking lugs -2- in direction of -arrow A-.
–Remove fuse holder C -1- far enough to get access to elec‐trical wires.
system - Edition 08.2022
NOTICE
Danger of connectors being inserted in incorrect position.
– Refer to the applicable current flow diagram to obtain infor‐mation on the exact pin assignment.
– Take photographs of the assignment of the electrical wires and fuses.
–Disconnect electrical wiring.
–Remove fuse holder C.
Installing
Install in reverse order of removal.
2.6.2Removing and installing bracket for fuse holder C [SC], left-hand drive ve‐hicles
The fuse holder C -SC- will henceforth be referred to as “fuse holder C”.
Removing
–Remove fuse holder C, and lay it aside with lines connected ⇒ a2.6.1 nd installing fuse holder C [SC], left-hand drive vehicles”, page 148 .
–Cut through cable tie on bracket for fuse holder C -2-.
–Release locking lugs -1-.
. icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole, isnotpermittedunlessauthorisedbyVolkswagen AG Volkswagen
–Remove bracket for fuse holder C-2- in direction of -arrow A-.
Installing
Install in reverse order of removal.
2.6.3Removing and installing fuse holder C [SC], right-hand drive vehicles
The fuse holder C -SC- will henceforth be referred to as “fuse holder C”.
CLICK HERE TO DOWNLOAD THE COMPLETE MANUAL
• Thank you very much for reading the preview of the manual.
• You can download the complete manual from: www.heydownloads.com by clicking the link below
• Please note: If there is no response to CLICKING the link, please download this PDF first and then click on it.
CLICK HERE TO DOWNLOAD THE
ID.3 2020 ➤
Electrical system - Edition 08.2022
Removing
–Disconnect battery ⇒ Rep. gr. 27; Disconnecting and con‐necting battery.
–Remove dash panel trim on front passenger side ⇒ General body repairs, interior; Rep. gr. 68; Compartments/covers; Removing and installing dash panel trim on front passenger side.
–Release locking lugs -2- in direction of -arrow A-.
–Remove fuse holder C -1- until electrical wires are accessi‐ble.
NOTICE
Danger of connectors being inserted in incorrect position.
– Refer to the applicable current flow diagram to obtain infor‐mation on the exact pin assignment.
– Take photographs of the assignment of the electrical wires and fuses.
–Disconnect electrical wiring.
isnotpermittedunlessauthorisedbyVolkswagen AG Volkswagen AGdoesnotguaranteeoracceptanyliabilitywi
–Remove fuse holder C.
Installing
Install in reverse order of removal.
2.6.4Removing and installing bracket for fuse holder C [SC], right-hand drive ve‐hicles
The fuse holder C -SC- will henceforth be referred to as “fuse holder C”.
Removing
–Remove fuse holder C, and lay it aside with lines connected ⇒ Rep. gr. 97; Removing and installing fuse holder C [SC].
–Cut through cable tie on bracket for fuse holder C -2-.
. icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole,
150 Rep. gr.97 - Wiring
thgirypocybdetcetorP . icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole,
–Release locking lug -1-.
–Remove bracket for fuse holder C-2- in direction of -arrow A-.
3.1.1Overview of fitting locations – control units, left-hand drive vehicles
1 - Data bus diagnostic inter‐face -J533-
❑⇒ Rep. gr. 97; Remov‐ing and installing data bus diagnostic interface [J533]
2 - Trailer detector control unit -J345-
❑⇒ General body re‐pairs, exterior; Rep. gr. 66; Towing brack‐et; Removing and in‐stalling trailer detector control unit [J345]
3 - Interface for entry and start system -J965-
❑⇒ Rep. gr. 94; Remov‐ing and installing inter‐face for entry and start system [J965]
4 - On-board supply control unit -J519-
❑⇒ Rep. gr. 97; Remov‐ing and installing on‐board supply control unit [J519]
3.1.2Overview of fitting locations – control units, right-hand drive vehicles
system - Edition 08.2022
1 - Interface for entry and start system -J965-
❑⇒ Rep. gr. 94; Remov‐ing and installing inter‐face for entry and start system [J965]
2 - Trailer detector control unit -J345-
❑⇒ General body re‐pairs, exterior; Rep. gr. 66; Towing brack‐et; Removing and in‐stalling trailer detector control unit [J345]
3 - Data bus diagnostic inter‐face -J533-
❑⇒ Rep. gr. 97; Remov‐ing and installing data bus diagnostic interface [J533]
4 - On-board supply control unit -J519-
❑⇒ Rep. gr. 97; Remov‐ing and installing on‐board supply control unit [J519]
3.2Assembly overview ? onboard supply control unit
3.2.1Assembly overview – onboard supply control unit, left-hand drive vehicles ID.3
1 - Interface for entry and start system -J965-
❑⇒ Rep. gr. 94; Remov‐ing and installing inter‐face for entry and start system [J965]
2 - Bracket for onboard supply control unit -J519-
❑⇒ Rep. gr. 97; Remov‐ing and installing brack‐et for onboard supply control unit [J519]
3 - On-board supply control unit -J519-
❑⇒ Rep. gr. 97; Remov‐ing and installing on‐board supply control unit [J519]
4 - Guide for centre electrical connector
5 - Bolt
❑4.5 Nm
. icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole, isnotpermittedunlessauthorisedbyVolkswage
1 - Bracket for onboard supply control unit -J519-
❑⇒ Rep. gr. 97; Remov‐ing and installing brack‐et for onboard supply control unit J519
2 - Onboard supply control unit -J519-
❑⇒ Rep. gr. 97; Remov‐ing and installing on‐board supply control unit J519
3 - Guide for centre electrical connector
3.3Removing and installing onboard sup‐ply control unit [J519]
3.3.1Removing and installing onboard sup‐ply control unit [J519], left-hand drive vehicles
The onboard supply control unit -J519- will henceforth be refer‐red to as “onboard supply control unit”.
Removing
If the onboard supply control unit is renewed, perform the test plan for the renewal of the onboard supply control unit:
–Carry out function “Renew onboard supply control unit” using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00; Access to diagno‐ses.
Continued –Remove footwell cover on driver side ⇒ General body re‐pairs, interior; Rep. gr. 68; Compartments/covers; Removing and installing footwell cover on driver side.
–Disconnect electrical connectors -2-.
GAnegawskloVybth
–Release retaining springs -3- in direction of -arrow A-.
–Swing onboard supply control unit -1- out of bracket -4-.
Installing
Install in the reverse order of removal, observing the following:
If the onboard supply control unit has been renewed, conclude the test plan for the renewal of the onboard supply control unit:
–Conclude function “Renew control unit” using ⇒ Vehicle di‐agnostic tester ⇒ Rep. gr. 00; Access to diagnoses.
Continued
–If the onboard supply control unit has been renewed, con‐clude the test plan for the renewal of the onboard supply control unit using ⇒ Vehicle diagnostic tester.
3.3.2Removing and installing onboard sup‐ply control unit [J519], right-hand drive vehicles
The onboard supply control unit -J519- will henceforth be refer‐red to as “onboard supply control unit”.
Removing
If the onboard supply control unit is renewed, perform the test plan for the renewal of the control unit:
–Carry out function “Renew control unit” using ⇒ Vehicle diag‐nostic tester ⇒ Rep. gr. 00; Access to diagnoses.
Continued –Remove dash panel trim on front passenger side ⇒ General body repairs, interior; Rep. gr. 68; Compartments/covers; Removing and installing dash panel trim on front passenger side. ID.3 2020 ➤ Electrical system - Edition 08.2022
–Disconnect electrical connectors -2-.
ID.3 2020 ➤ Electrical system - Edition 08.2022
–Release retaining springs -3- in direction of -arrow A-.
–Swing onboard supply control unit -1- out of bracket -4-.
Installing
Install in the reverse order of removal, observing the following:
If the onboard supply control unit has been renewed, conclude the test plan for the renewal of the onboard supply control unit:
–Conclude function “Renew control unit” using ⇒ Vehicle di‐agnostic tester ⇒ Rep. gr. 00; Access to diagnoses.
Continued
–If the onboard supply control unit has been renewed, con‐clude the test plan for the renewal of the onboard supply control unit using ⇒ Vehicle diagnostic tester.
3.4Removing and installing bracket for on‐board supply control unit [J519]
3.4.1Removing and installing bracket for on‐board supply control unit [J519], lefthand drive vehicles
The onboard supply control unit -J519- will henceforth be refer‐red to as “onboard supply control unit”.
Removing
–Remove dash panel ⇒ General body repairs, interior; Rep. gr. 70; Dash panel; Removing and installing dash panel.
–Remove bracket for fuse holder C [SC] ⇒ a2.6 nd installing fuse holder C [SC]”, page 148
–Remove onboard supply control unit ⇒ Rep. gr. 97; Remov‐ing and installing bracket for onboard supply control unit [J519].
–Remove interface for entry and start system -J965- ⇒ Rep. gr. 94; Remove interface for entry and start system [J965].
Electrical system - Edition 08.2022
–Unscrew bolt -2-. –Release locking lugs -1-.
thgirypocybdetcetorP . icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole, isnotpermittedunlessauthorisedbyVolkswagen
–Cut through cable tie on bracket for onboard supply control unit -1-.
–Release bracket for onboard supply control unit -2- in direc‐tion of -arrow A-.
–Remove bracket for onboard supply control unit -2- in direc‐tion of -arrow B-.
Installing
Install in the reverse order of removal, observing the following: Tightening torques
♦ ⇒ Rep. gr. 97; Assembly overview – onboard supply control unit ID.3 2020 ➤
3.4.2Removing and installing bracket for on‐board supply control unit [J519], righthand drive vehicles
The onboard supply control unit -J519- will henceforth be refer‐red to as “onboard supply control unit”.
Removing
–Remove onboard supply control unit -J519- ⇒ Rep. gr. 97; Removing and installing bracket for onboard supply control unit [J519].
–Unscrew bolts -2- and -3-.
–Remove strut -1-.
thgirypocybdetcetorP . icremmocroetavirprofgniypoCla rup op s e s , i n p a r t o r in w hole, isnotpermittedunlessauthorisedbyVolkswagen AG Volkswagen
–Cut through cable tie on bracket for onboard supply control unit -2-.
AGdoesnotguaranteeoracceptanyliabilitywi
–Release locking lug -1-.
–Release bracket for onboard supply control unit -2- in direc‐tion of -arrow A-.
–Remove bracket for onboard supply control unit -2- in direc‐tion of -arrow B-.
Installing
Install in reverse order of removal. ID.3 2020 ➤
system - Edition 08.2022
CLICK HERE TO DOWNLOAD THE COMPLETE MANUAL
• Thank you very much for reading the preview of the manual.
• You can download the complete manual from: www.heydownloads.com by clicking the link below
• Please note: If there is no response to CLICKING the link, please download this PDF first and then click on it.
