Miniaturisation Method to Reduce the Size of Microstrip Antenna for Lower Frequency

International Journal for Scientific Research & Development (IJSRD) | Vol. 1, Issue 1, 2013 | ISSN(online): 2321-0613

Miniaturisation Method to Reduce the Size of Microstrip Antenna for Lower Frequency Deepak Moghariya1 Mr. Tejas Kothari2 Prof. M. P. Patel3 1,2

3

P.G. Student, E & C Engineering Department Associate Professor, E & C Engineering Department 1,2,3 S.S.Engineering College, Bhavnagar

Abstract-The telecommunication always tries to reach the best performances, the reliability and the efficiency with the lowest possible costs. Novel investigation of a microstrip antennas compacts conception with a wideband, a double frequency, a double band, an enhanced gain of operation etc. Aim of this paper is to reduce the size of antenna for lower frequency. For this purpose different techniques are presented. Here four methods are presented for size reduction (shorting post, structure modification etc.). Each method is capable for reduce the size but each has its own merits and demerits. Using combination of two or more methods, it is possible reduce size according our requirement without much more affecting other parameters. In this paper, I present simulation for structure modification technique to reduce size using HFSS13, I got size reduction as well reduce resonant frequency. Keywords: HFSS, Shorting Post, Structure Modification I. INTRODUCTION An explosive growth of the wireless radio communication systems is currently observed in the microwave band. In the short range communications or contactless identification systems, antennas are key components, which must be small, low profile, and with minimal processing costs. The Microstrip patch antennas are of great interest for aforementioned mentioned applications due to their compact structure. The flexibility afforded by microstrip antenna technology has led to a wide variety of design and techniques. The main limitations of the microstrip antennas are low efficiency and narrow impedance bandwidth. The bandwidth of the microstrip antenna can be increased using various techniques such as by loading a patch, by using a thicker substrate, by reducing the dielectric constant, by using gap-coupled multi-resonator etc. There exist a wide range of basic microstrip antenna shapes such as rectangular, circular and triangular patch shapes which are commonly used patches. For these patches, operating at their fundamental mode resonant frequency, are of the dimension of the patch is about half wavelength in dielectric. At lower frequencies the size of the microstrip antennas becomes large. In modern communication systems the compact microstrip patch antennas are desirable. There are various techniques to reduce the size of the microstrip antennas. II. BASIC STRUCTURE OF MICROSTRIP ANTENNA [1] A microstrip antenna in its simplest form consists of a

radiating patch on one side of a dielectric substrate and a ground plane on the other side

Fig.1. Microstrip Patch Antenna Structure

 Patch: present the radiant conductive element and which can take several forms  Substrate: allows isolating both conductive planes, characterized by the permittivity  Ground plane: conductor situated below the circuit on which is placed the substrate  Feed line: used to excite to radiate by direct or indirect contact. III. SIZE REDUCTION TECHNIQUES However microstrip antennas are typically used at frequencies of 1GHz or higher. At lower frequencies, size of antenna becomes serious issue for practical deployment. However, for reduction the size of antenna there are various method, the different method are as follows:

1) 2) 3) 4)

High dielectric constant Shorting Post Structural modification Perturbation and Plate loading

1) High dielectric constant: Simple method to reduce size of antenna is use of high dielectric constant material; however this method leads to decrease in radiation efficiency, narrower bandwidth and increase antenna weight. 2) Shorting Post [3]: A common technique to reduce the overall size of a micro-strip patch antenna is to terminate one of the radiating edges with a short circuit. The short circuit can be in the form of a metal clamp or a series of shorting posts. It was shown that by changing the number of shorting posts and the relative position of these posts, the resonance frequency of the short-circuited microstrip patch can be adjusted. In fact, by reducing the number of shorting posts the resonance frequency of the modified patch can be reduced. By loading of the microstrip antenna with shorting

26

Miniaturisation Method to Reduce the Size of Microstrip Antenna for Lower Frequency (IJSRD/Vol. 1/Issue 1/2013/0008)

post, the size of the microstrip antennas can be reduced as well as multi-frequency operation, change of polarization etc can be achieved. Rectangular microstrip antenna loaded with shorting post at the center line is shown below fig.2.

Amount of energy stored in the electric field should be decreased, while that in magnetic field should be increase. Therefor upper part of antenna decreased because electric field is strong there, while lower part increased because magnetic field is strong there. With an increase in number of plate loaded on the microstrip antenna, the current path of antenna increase, and hence the resonant frequency decreases. For further reduction in size can be achieved by combining these two methods, as shown fig.4. IV. SIMULATION

Fig.2. Rectangular microstrip antenna loaded with shorting post [3]

Pin Shorted Microstrip Antenna for Mobile Communication applications as shown in below figure 3.

Fig.3. Pin Shorted Microstrip Antenna[3]

3) Structural modification [5]: Another way to make microstrip antenna smaller by modify its shape, by inserting slot to meander currents. By changing number of slot, width and length of slot we can reduce the size of antenna.

I have designed antenna for frequency 100MHz. dimension get from equation [8] are [for É&#x203A;r=2.1(teflon), fr=100MHz] Lg=1519mm,Wg=1745mm,(size of ground) Lp=979mm,Wp=1205mm,(size of patch) height of substrate=90mm

Fig. 4. Design of Antenna

Return Loss:

Fig. 5. Return loss for designed Antenna

VSWR:

Fig.4. Patch with slot inserted [9]

4) Perturbation and Plate loading [4]: For reducing size of microstrip antenna based on perturbation effect, Fig. 6. VSWR for designed antenna

Now I insert slot means structure modification, size of antenna reduce to Lg=1350mm,Wg=1400mm, Lp=700mm,Wp=900mm, height of substrate=70mm

Fig. 4Perturbation and Plate loading [4]

Fig. 7. Modified Antenna Design

27

Miniaturisation Method to Reduce the Size of Microstrip Antenna for Lower Frequency (IJSRD/Vol. 1/Issue 1/2013/0008)

Return Loss:

Fig. 8. Return loss of Modified Design

VSWR:

Fig. 9. VSWR of Modified Design

V. CONCLUSION Here in this paper I have presented some method to reduce size of antenna; each method has its own merits and demerits. One can use any one or combination of these methods to reduce size of antenna nearly approximate to requirement. I have designed antenna for 100MHz using structure modification, I got result without much more affecting main parameter for size reduce antenna. I got reduce in size as well as in resonant frequency. REFERENCES [1]. D. Orban, and G. J. K. Moernaut, “The Basics of Patch Antennas,’’ Orban Microwave Products. [2]. Zaakri Safa, Zenkouar Lahbib “Simulation of a Rectangular Patch Antenna”, Vol. 2, No. 1, 2012 [3]. Pradeep Kumar, G. Singh “Microstrip Antennas Loaded with Shorting Post” May 14, 2009 [4]. S.-M. Moon, H.-K. Ryu, J.-M. Woo and H. Ling “Miniaturisation of λ/4 microstrip antenna using perturbation effect and plate loading for low-VHF-band applications”, 3rd February 2011 Vol. 47 No. 3 [5]. Romain Pascaud “Compact Dual-Polarized VHF Microstrip Antenna for Satellite Applications”, 2012 [6]. Constantine A. Balanis “Antenna Theory: Analysis and Design” 3rd edition 2005 [7]. Shirt Fun ooi, “Design of a high efficiency class Fpower amplifier integrated with A Microstrip Patch Antenna” August 2007 [8]. R.Garg, P.Bhartia, I.Bahl, A.Ittipibon “Microstrip Antenna Design Handbook”, Artech House, BostonLondon, 2001 [9].Small Antennas: Miniaturization Techniques and Applications, Davor Bonefacic, Juraj Bartolic, 2012

28

Turn static files into dynamic content formats.

Create a flipbook

Miniaturisation Method to Reduce the Size of Microstrip Antenna for Lower Frequency

Published on Mar 6, 2014

International Journal for Scientific Research and Development - IJSRD

The telecommunication always tries to reach the best performances, the reliability and the efficiency with the lowest possible costs. Novel investigation of a microstrip antennas compacts conception with a wideband, a double frequency, a double band, an enhanced gain of operation etc. Aim of this paper is to reduce the size of antenna for lower frequency. For this purpose different techniques are presented. Here four methods are presented for size reduction (shorting post, structure modification etc.). Each method is capable for reduce the size but each has its own merits and demerits. Using combination of two or more methods, it is possible reduce size according our requirement without much more affecting other parameters. In this paper, I present simulation for structure modification technique to reduce size using HFSS13, I got size reduction as well reduce resonant frequency.