r e s p i r ato ry p r ot e c t i o n
My-T- Gear
Why respiratory protection? Anyone who is or might be going to work in an environment where the air is polluted, and who wants to stay safe, must first ask themselves whether the space they are entering is suitable for people to occupy and/or work in. Is there enough oxygen? Are the pollutants one could encounter known? And could the activities to be performed also produce contamination. Many of the activities involve working in dust, smoke or mists. In the field of respiratory protection, these are all seen as particles. In this sense viruses and bacteria can also be seen as particles. My-T-Gear dust masks offer adequate protection in many cases. If, in addition to dust, there are dangerous concentrations of gases and/or vapours, then the dust mask is not sufficient and other measures must be taken.
Any form of fine dust is unhealthy but not all particles are equally dangerous. Hardwood and quartz dust, for instance, are very dangerous. A list of the current limit values* can be purchased from Sdu Publishers. For more information please contact you deaker.
European Standard for dust masks The My-T-Gear masks in this brochure all comply with the European Standard NEN-EN 149:2001 with supplement A1:2009. An important property of the dust masks is that they are intended for one-off use and are maintenancefree. The dust masks can be divided into three categories: FFP1, FFP2 and FFP3. The higher the number, the more particles the mask will keep out and the higher the protection factor (NPF). Information about the category of the mask can be found on the mask itself.
Health risks from particles Dust, fibres, particles, etc., can irritate the nose, throat and upper airways. Fine dust particles can penetrate the lungs, where they can damage the lung tissue or even end up in the bloodstream. This can cause many health problems, varying from irritation to serious diseases such as pneumoconiosis or even, in the worst scenario, cancer.
*Limit values are the maximum concentrations of a particular substance in which, based on the present state of knowledge, it is still safe to work. Measures must be taken when concentrations exceed the limit value.
My-T- Gear Carrying out work in industry is synonymous with danger. Every professional operator will endeavour to reduce the risks involved as much as possible. Wearing the correct personal protective equipment (PPE) is therefore essential for every tradesman. The difficulty lies in getting “the right� PPE kit. The range of PPE as far as we are concerned has become too large.
This is why the My-T-Gear collection consists of a limited number of items in each product group. Our experts have cut down the overall range to a manageable size. In each group you will find protection equipment to match the risk to which you will be exposed at work.
My-T-Gear the new standard in Personal Safety! A new line that demonstrates high quality and affordability can go firmly hand in hand with an up-todate image and design. A brand for craftsmen who believe in the power of simplicity.
Assortimentstabel Item number
Product
Standard
Filter class
NPF*
Exhalation valve
Mask 301
EN 149:2001 A1:2009
FFP1 NR
4
Mask 302
EN 149:2001 A1:2009
FFP2 NR
Mask 312
EN 149:2001 A1:2009
Mask 322
Special features
Packaging
Type of mask
no
box of 20 pieces
preformed cup mask
12
no
box of 20 pieces
preformed cup mask
FFP2 NR
12
yes
box of 10 pieces
preformed cup mask
EN 149:2001 A1:2009
FFP2 NR
12
yes
activated charcoal against unpleasant smells
box of 10 pieces
preformed cup mask
Mask 412
EN 149:2001 A1:2009
FFP2 NR D
12
yes
adjustable straps
box of 10 pieces
folded mask, individually packed
Mask 313
EN 149:2001 A1:2009
FFP3 NR
50
yes
adjustable straps
box of 5 pieces
preformed cup mask
Mask 413
EN 149:2001 A1:2009
FFP3 NR D
50
yes
adjustable straps
box of 10 pieces
folded mask, individually packed
154846
154847
154848
154849
154851
154850
154852
*NPF: Nominal protection factor
My-T- Gear
Mask 412
Fitting 1
2+3
1 H old mask firmly and place the bottom headband over the head to the nape of the neck. 2 Place the mask over nose putting the top headband over the crown of the head. 3 Press the nose clip to secure that it is securely molded around the nose, resting the ends against the cheek to obtain a good seal.
4
4 To check the fit, place both hands completely over the respirator and inhale vigorously. If air leeks at the edge, readjust the mask, manipulating the nose bridge and headband to effect an acceptable seal. If a proper seal cannot be achieved do not enter the contaminated area.
Dust mask parts Face seal Prevents leaking between the mask and the face.
Nose clip The nose clip allows the mask to be adjusted to fit each individual face. Exhalation valve Ensures rapid discharge of exhaled air, preventing unnecessary build-up of warmth and moisture in the masks. Filter fabric The most important medium for keeping out the dust with the lowest possible breathing resistance.
(Adjustable) straps The straps ensure that the mask remains in place during use. They are elastic and can be adjusted.
Standards On the mask the standard to which the mask was tested (EN149 + year) is placed in combination with the filter class for this mask FFP1, FFP2 and FFP3. Further away the mask indicated the letters R or NR. This indicates whether the mask of Non-Reusable is Reusable.
• Disposable dust mask • Expandable mask • Standards: EN 149:2001 - A1:2009 FFP2 NR D • NPF: 12 • With exhalation valve • With adjustable straps • Each mask has individually packaging • Box of 10 pieces Article number: 154851
Mask 413 • Disposable dust mask • Expandable mask • Standards: EN 149:2001 - A1:2009 FFP3 NR D • NPF: 50 • With exhalation valve • With adjustable straps • Each mask has individually packaging • Box of 10 pieces Article number: 154852
Mask 301
Mask 312
• Disposable dust mask • Molded mask • Standards: EN 149:2001 - A1:2009 FFP1 NR • NPF: 4 • Without exhalation valve • Box of 20 pieces Article number: 154846
• Disposable dust mask • Molded mask • Standards: EN 149:2001 - A1:2009 FFP2 NR • NPF: 12 • With exhalation valve • Box of 10 pieces Article number: 154848
Mask 322
Mask 302 • Disposable dust mask • Molded mask • Standards: EN 149:2001 - A1:2009 FFP2 NR • NPF: 12 • Without exhalation valve • Box of 20 pieces Article number: 154847
• Disposable dust mask • Molded mask • Standards: EN 149:2001 - A1:2009 FFP2 NR • NPF: 12 • Could also be used for working with organic gas and steam below the limiting value. • With exhalation valve • Box of 10 pieces Article number: 154849
Mask 313 • Disposable dust mask • Molded mask • Standards: EN 149:2001 - A1:2009 FFP3 NR • NPF: 50 • With exhalation valve • With adjustable straps • Box of 5 pieces Article number: 154850
Respiratory protection Working with:
FFP1 Mask 301
FFP2 Mask 302
Mask 312
FFP3 Mask 322
Mask 412
Mask 313
Mask 413
Bacteria Beech Cement Concrete dust Coolant spray Degreaser Fiberglass Fungi Grain Gypsum Iron (fillings, dust) Lubricating oil mist Metal dust Mineral fiber Oak Paint powder (powder coating) Pet food (dry) Plaster wall Putty Quartz dust Rust Steel (fillings, dust) Viruses Waste Water-based pesticides Wood
These tables are for information and incomplete. No rights can be derived from these tables. Advice dependents on types and concentrations.
You r My-T- Gear deal er
Contact information
My-T-Gear info@my-t-gear.com www.my-t-gear.com The information in the brochure is intended for general information purposes only and is not intended as advice, design (construction), calculation, warranty or otherwise for the user. Printing errors are reserved. Intersafe gives no warranty and accepts no responsibility for the accuracy and/or completeness of the information (including the Intersafe products) and that the information is suitable for the purpose for which the user is consulted or otherwise. Users, customers and third parties are themselves responsible and should take their responsibility to verify that the goods are suitable for their intended application by getting a professional advisor to get information about (the predisposition of the) Intersafe products all desired applications and applicable legislation and regulations. All our agreements are subject to our Terms of Sale and Delivery, filed in the Registry of the Court of Dordrecht and downloadable from www.intersafe.eu. They are on request free of charge. The conditions include a limitation on liability. Other terms and conditions (of counterparties) are explicitly rejected.