● ISO 9001: 2008 Certificate
● Air Impulse Tools
2
● Air Industrial Screwdrivers
● Industrial Cordless Tools
● Air Industrial Impact Wrench
3
<SQ. Drive Type>
R
Air Impulse Tools
â&#x2014;&#x2DC; Table of Contents: Air Impulse Tools SQ. Drive Type Bit. Shank Type Straight SQ. Drive Straight Bit Shank Angle SQ. Drive Angle Bit Shank Sleeve Drive Socket & Impulse Oil
Air Industrial Screwdrivers Pistol Type Push Start Lever Start Angle Type
Industrial Cordless Tools
5 8 12 13 14 15 16 17 18 21 22 23 24 25
SCB series (Shut-off screwdriver with brushless motor)
27
SC series (Shut-off screwdriver with brush motor)
30
WR series (Shut-off angle wrench/screwdrivers with brushless motor)
32
Accessories
34
Air Industrial Impact Wrench
37
Digital Torque Wrench
41
Remarks:
According to different working conditions and joint types, the torque range of the impulse tools may vary comparing to the actual torque range tested in the lab. Therefore, we recommend testing the impulse tool you choose in the practical working station before real work to make sure if this tool can literally reach the desired torque. The following guides would help you choose the most suitable tool for your work.
1.Hard Joint Applications:
The shut off impulse tools normally reach 85% of the maximum torque listed in the Torque Range List. The non shut off impulse tools normally reach 95% of the maximum torque listed in the Torque Range List.
2.Soft Joint Applications:
The shut off impulse tools normally reach 70% of the maximum torque listed in the Torque Range List. The non shut off impulse tools normally reach 90% of the maximum torque listed in the Torque Range List
3. All tools are tested in Tranmax labtory and the all torques are measured by the precise
testers at a dynamic airpressure of 5 and 6 kg/cm2.All torques are for a guidance only. The numbers may vary in case of using lower air pressure and some possible accessories.
4
R
Air Impulse Tools
TIGHTENING TORQUE (N.m) This table shows the recommended tightening torque for common bolt size M2 to M48. According to ISO 898-1. Bolt Size
Bolt Grade
Bolt Size
Bolt Grade
mm
3.0
4.6
4.8
5.8
8.8
10.9
12.9
mm
4.6
4.8
5.8
8.8
10.9
12.9
M2
0.10
0.13
0.17
0.22
0.35
0.49
0.58
M18
103
121
172
275
386
463
M3
0.35
0.46
0.61
0.77
1.20
1.70
2.10
M20
144
170
240
385
541
649
M4
0.81
1.10
1.40
1.80
2.90
4.00
4.90
M22
194
230
324
518
728
874
M5
0.60
2.20
2.95
3.60
5.70
8.10
9.70
M24
249
295
416
665
935
1120
M6
2.80
3.70
4.90
6.10
9.80
14.0
17.0
M27
360
435
600
961
1350
1620
M8
8.9
10.5
15
24
33
40
M30
492
590
819
1310
1840
2210
M10
17
21
29
47
65
79
M36
855
1030
1420
2280
3210
3850
M12
30
36
51
81
114
136
M42
1360
2270
3640
5110
6140
M14
48
58
80
128
181
217
M45
1690
2820
4510
6340
7610
M16
74
88
123
197
277
333
M48
2040
3400
5450
7660
9190
TORQUE RANGE REFERENCE Torque is a very important reference value while choosing a right tool for tightening. Due to the actual tighten torque may vary because of nut sizes, joint types, air pressure and working environment, the above table is only for a reference to choose a right tool. When the working torque is at the mean value of the torque range, the tool provides the best performance. BOLT GRADE at 8.8 SQ.DRIVE TYPE TDI(S)-30 TDI(S)-40 TDI(S)-50 TDI(S)-60 TDI(S)-65 TDI(S)-70X TDI(S)-70 TDI(S)-80 TDI(S)-80H TDI(S)-90 TDI(S)-100 TDI(S)-130 TDI(S)-150 TDI(S)-180
M6
M8
M10
M12
M14
M18
M16
BIT SHANK TYPE TDI(S)-30D TDI(S)-40D TDI(S)-50D TDI(S)-60D TDI(S)-65D TDI(S)-70D STRAIGHT SQ.DRIVE TDI(S)-30S TDI(S)-40S TDI(S)-50S TDI(S)-60S TDI(S)-70S TDI(S)-80S STRAIGHT BIT SHANK TDI(S)-30SD TDI(S)-40SD TDI(S)-50SD TDI(S)-60SD TDI(S)-70SD ANGLE SQ.DRIVE TDI(S)-50R TDI(S)-60R TDI(S)-70R TDI(S)-70RG TDI(S)-70RH TDI(S)-80RH ANGLE BIT SHANK TDI(S)-50RD TDI(S)-60RD TDI(S)-70RD 20
40
60
80
100
120
140
160
To r q u e ( N . m )
180
200
220
240
260
280
300
5
X-Shape Sealing improves better repeatability
Twin Drive Blades reduce noise and vibration and increase impulse frequency
One hand reverse operation for Right or Left handed operators
Easy Torque Adjustment The desired torque can be easily adjusted by turning the adjusting screw through the hole on the pulse unit housing. 360â&#x2014;Ś revolving low noise exhaust device 6
Conventional Impact Wrench
Torque
Conventional
New Design
Unibodied Front End Plate & Cylinder advance the Motor Efficiency
OUT
Double-Chamber Motor
IN
A smart design of a dual air motor for impulse wrenches. The double OUT chamber air motor reaches the required toruqe quickly that increases work efficiency.
OUT
IN
OUT
→ Conventional Motor Speed R.P.M.
→ Double-Chamber Motor Torque
Handle Rubber Injection: designed ergonomically for operation comfortable 7
<SQ. Drive Type>
R
Air Impulse Tools
TDI-130 TDIS-130
TDI-150 TDIS-150
TDI-180 TDIS-180
Non shut-off SQ Drive Bolt mm(“) Capacity
Torque Range N-m (ft-lb) 5-6kg/cm2
TDI-130 12.7(1/2”) M14-M16
113-148(83.2-109)
3300
Model
Free Speed
Noise Average Air Vibration Level Consumption Value Hose Size dB(A) m3/min ft3/min m/s2
Weight Length
5kg/cm2 6kg/cm2
kg
mm
3600
2.22
216
86
0.73
25.6
2.7
11
TDI-150
19(3/4”)
M16
145-210(106.8-154.6)
3500
3700
3.05
238
86
0.73
25.6
2.9
11
TDI-180
19(3/4”)
M16-M18
180-255(132-188)
2500
2700
3.8
264
86
0.73
25.6
3.4
11
Auto shut-off SQ Drive Bolt mm(“) Capacity
Torque Range N-m (ft-lb) 5-6kg/cm2
TDIS-130 12.7(1/2”) M14-M16
113-148(83.2-109)
3300
M16
145-210(106.8-154.6)
M16-M18
180-255(132-188)
Model
TDIS-150 19(3/4”) TDIS-180
19(3/4”)
Free Speed 5kg/cm2 6kg/cm2
kg
mm
3600
2.26
216
86
0.73
25.6
2.7
11
3500
3700
3.10
238
86
0.73
25.6
2.9
11
2500
2700
3.9
264
86
0.73
25.6
3.4
11
★ Air Inlet：TDI(S)-30~150：NPT 1/4” TDI(S)-180：NPT 3/8” ★ Recommended Air Pressure：70~85 PSI(5 kg/cm2~6 kg/cm2) / 0.5MPa~ 0.6 MPa ★ Air Hose Size：10mm×6.5mm×5m for TDI(S)-30~50 12mm×8mm×5m for TDI(S)-60~100
a
16mm×11mm×5m for TDI(S)-130~180
φc φe
Dimensions b
d
8
Noise Average Air Vibration Level Consumption Value Hose Size dB(A) m3/min ft3/min m/s2
Weight Length
Model
a (mm)
b (mm)
c (mm)
d (mm)
e (mm)
TDI(S)-130
216
204
ø 64
31
ø 16
TDI(S)-150
239
215
ø 72
40
ø 25
TDI(S)-180
264
232
ø 78
41
ø 25
R
<SQ. Drive Type>
Air Impulse Tools
TDI-90 TDIS-90
TDI-80(H) TDIS-80(H)
TDI-100 TDIS-100
TDI(S)-80H is 1/2” SQ.Drive
Non shut-off Model
SQ Drive Bolt mm(“) Capacity
Torque Range N-m (ft-lb) 5-6kg/cm2
TDI-80
9.5(3/8”) M10-M12
40-70(29.5-51.5)
4800
TDI-80H 12.7(1/2”) M10-M12
40-72(29.5-53)
TDI-90
12.7(1/2”)
M12
TDI-100 12.7(1/2”) M12-M14
Free Speed
Noise Average Air Vibration Level Consumption Value Hose Size dB(A) m3/min ft3/min m/s2
Weight Length
5kg/cm2 6kg/cm2
kg
mm
5100
1.19
194
82
0.5
17.6
<2.5
8
4800
5100
1.25
200
82
0.5
17.6
<2.5
8
57-90(42-66.3)
5000
5400
1.53
200
83
0.53
18.7
<2.5
8
75-120(55.2-88.4)
5000
5300
1.85
209
84
0.55
19.4
<2.5
8
Auto shut-off Model
SQ Drive Bolt mm(“) Capacity
Torque Range N-m (ft-lb) 5-6kg/cm2
TDIS-80
9.5(3/8”) M10-M12
40-68(29.5-50)
4800
40-70(29.5-51.5)
TDIS-80H 12.7(1/2”) M10-M12 TDIS-90 12.7(1/2”)
M12
TDIS-100 12.7(1/2”) M12-M14
Free Speed 5kg/cm2 6kg/cm2
kg
mm
5100
1.21
194
82
0.5
17.6
<2.5
8
4800
5100
1.27
200
82
0.5
17.6
<2.5
8
57-90(42-66.3)
5000
5400
1.55
200
83
0.53
18.7
<2.5
8
75-120(55.2-88.4)
5000
5300
1.87
209
84
0.55
19.4
<2.5
8
★ Air Inlet：TDI(S)-30~150：NPT 1/4” TDI(S)-180：NPT 3/8” ★ Recommended Air Pressure：70~85 PSI(5 kg/cm2~6 kg/cm2) / 0.5MPa~ 0.6 MPa ★ Air Hose Size：10mm×6.5mm×5m for TDI(S)-30~50 12mm×8mm×5m for TDI(S)-60~100
a
16mm×11mm×5m for TDI(S)-130~180
Dimensions Model
d
b
φc φe
Noise Average Air Vibration Level Consumption Value Hose Size dB(A) m3/min ft3/min m/s2
Weight Length
a (mm)
b (mm)
c (mm)
d (mm)
e (mm)
TDI(S)-80
194
170
ø 47
25
ø 12
TDI(S)-80H
200
170
ø 47
31
ø 16
TDI(S)-90
200
192
ø 53.5
31
ø 16
TDI(S)-100
209
195
ø 59
32
ø 16
9
<SQ. Drive Type>
R
Air Impulse Tools
TDI-65 TDIS-65
TDI-70X TDIS-70X
TDI-70 TDIS-70
Non shut-off Model TDI-65
SQ Drive Bolt mm(“) Capacity 9.5(3/8”)
M10
TDI-70X 9.5(3/8”) M10-M12 TDI-70
9.5(3/8”) M10-M12
Torque Range N-m (ft-lb) 5-6kg/cm2
Free Speed
Noise Average Air Vibration Level Consumption Value Hose Size dB(A) m3/min ft3/min m/s2
Weight Length
5kg/cm2 6kg/cm2
kg
mm
27-45(19.8-33.1)
4500
4800
1.05
189
82
0.43
15.2
<2.5
8
32-55(23.5-40.5)
5200
5400
1.05
189
82
0.45
15.9
<2.5
8
34-57(25-42)
6900
7200
1.33
194
82
0.45
15.9
<2.5
8
Auto shut-off Model TDIS-65
SQ Drive Bolt mm(“) Capacity 9.5(3/8”)
M10
TDIS-70X 9.5(3/8”) M10-M12 TDIS-70
9.5(3/8”) M10-M12
Torque Range N-m (ft-lb) 5-6kg/cm2
Free Speed 5kg/cm2 6kg/cm2
kg
mm
27-45(19.8-33.1)
4500
4800
1.08
189
82
0.43
15.2
<2.5
8
32-54(23.5-40)
5200
5400
1.08
189
82
0.45
15.9
<2.5
8
34-57(25-42)
6900
7200
1.35
194
82
0.45
15.9
<2.5
8
★ Air Inlet：TDI(S)-30~150：NPT 1/4” TDI(S)-180：NPT 3/8” ★ Recommended Air Pressure：70~85 PSI(5 kg/cm2~6 kg/cm2) / 0.5MPa~ 0.6 MPa ★ Air Hose Size：10mm×6.5mm×5m for TDI(S)-30~50 12mm×8mm×5m for TDI(S)-60~100
16mm×11mm×5m for TDI(S)-130~180
Dimensions
d
Model
b
φc φe
a
10
Noise Average Air Vibration Level Consumption Value Hose Size dB(A) m3/min ft3/min m/s2
Weight Length
a (mm)
b (mm)
c (mm)
d (mm)
e (mm)
TDI(S)-65
189
170
ø 47
25
ø 12
TDI(S)-70X
189
170
ø 47
25
ø 12
TDI(S)-70
194
192
ø 53.5
25
ø 12
R
<SQ. Drive Type>
Air Impulse Tools
TDI-30 • 40 TDIS-30 • 40
TDI-50 TDIS-50
TDI-60 TDIS-60
Non shut-off Torque Range N-m (ft-lb) 5-6kg/cm2
Free Speed
Model
SQ Drive Bolt mm(“) Capacity
TDI-30
9.5(3/8”)
M6
6-12.5(4.4-9.2)
4300
TDI-40
9.5(3/8”)
M6-M8
10-19(7.4-14)
TDI-50
9.5(3/8”)
M8
TDI-60
9.5(3/8”)
M8-M10
Noise Average Air Vibration Level Consumption Value Hose Size dB(A) m3/min ft3/min m/s2
Weight Length
5kg/cm2 6kg/cm2
kg
mm
4600
0.87
167
78
0.25
8.8
<2.5
6.5
4300
4600
0.9
167
78
0.25
8.8
<2.5
6.5
13-27(9.6-19.9)
6800
7200
0.9
167
80
0.35
12.3
<2.5
6.5
20-35(14.7-25.8)
5900
6200
0.97
178
82
0.4
14.1
<2.5
8
Auto shut-off Model
SQ Drive Bolt mm(“) Capacity
Torque Range N-m (ft-lb) 5-6kg/cm2
Free Speed
Noise Average Air Vibration Level Consumption Value Hose Size dB(A) m3/min ft3/min m/s2
Weight Length
5kg/cm2 6kg/cm2
kg
mm
TDIS-30 9.5(3/8”)
M6
6-12.5(4.4-9.2)
4300
4600
0.89
167
78
0.25
8.8
<2.5
6.5
TDIS-40 9.5(3/8”)
M6-M8
10-19(7.4-14)
4300
4600
0.92
167
78
0.25
8.8
<2.5
6.5
TDIS-50 9.5(3/8”)
M8
13-27(9.6-19.9)
6800
7200
0.92
167
80
0.35
12.3
<2.5
6.5
TDIS-60 9.5(3/8”)
M8-M10
20-35(14.7-25.8)
5900
6200
1.0
178
82
0.4
14.1
<2.5
8
★ Air Inlet：TDI(S)-30~150：NPT 1/4” TDI(S)-180：NPT 3/8” ★ Recommended Air Pressure：70~85 PSI(5 kg/cm2~6 kg/cm2) / 0.5MPa~ 0.6 MPa ★ Air Hose Size：10mm×6.5mm×5m for TDI(S)-30~50 12mm×8mm×5m for TDI(S)-60~100
Dimensions
d
b
φc φe
a
16mm×11mm×5m for TDI(S)-130~180
Model
a (mm)
b (mm)
c (mm)
d (mm)
e (mm)
TDI(S)-30
167
168
ø 46
24
ø 12
TDI(S)-40
167
168
ø 46
24
ø 12
TDI(S)-50
167
168
ø 46
24
ø 12
TDI(S)-60
178
168
ø 46
24
ø 12
11
<Bit Shank Type>
R
Air Impulse Tools
TDI-30D • 40D TDIS-30D • 40D
TDI-60D• 65D TDIS-60D • 65D
TDI-50D TDIS-50D
TDI-70D TDIS-70D
Non shut-off Model
Hex Size mm(“)
TDI-30D 6.35Hex(1/4”)
Bolt Capacity M6
TDI-40D 6.35Hex(1/4”) M6-M8 TDI-50D 6.35Hex(1/4”)
M8
TDI-60D 6.35Hex(1/4”)
M8
TDI-65D 6.35Hex(1/4”) M8-M10 TDI-70D 6.35Hex(1/4”)
M10
Noise Average Air Vibration Torque Range N-m Free Speed Weight Length Bit Level Consumption Value Hose (ft-lb) Size Shank 2 2 2 3 3 5-6kg/cm 5kg/cm 6kg/cm kg mm dB(A) m /min ft /min m/s2 5-12.5(3.7-9.2)
9mm
4300
4600
0.87
163
78
0.25
8.8
<2.5
6.5
9-18(6.6-13.3)
9mm
4300
4600
0.9
170
78
0.25
8.8
<2.5
6.5
12-26(8.8-19.2)
9mm
6800
7200
0.9
170
80
0.35
12.3
<2.5
6.5
18-30(13.3-22.1) 9mm
5900
6200
0.97
181
82
0.4
14.1
<2.5
8
9mm
4500
4800
1.05
192
82
0.43
15.2
<2.5
8
29-47(21.4-34.6) 9mm
6900
7200
1.33
197
82
0.45
15.9
<2.5
8
23-38(16.9-28)
Auto shut-off Model
Hex Size mm(“)
TDIS-30D 6.35Hex(1/4”)
Bolt Capacity M6
TDIS-40D 6.35Hex(1/4”) M6-M8 TDIS-50D 6.35Hex(1/4”)
M8
TDIS-60D 6.35Hex(1/4”)
M8
TDIS-65D 6.35Hex(1/4”) M8-M10 TDIS-70D 6.35Hex(1/4”)
M10
Noise Average Air Vibration Torque Range N-m Free Speed Weight Length Bit Level Consumption Value Hose (ft-lb) Size Shank 2 2 2 3 3 5-6kg/cm 5kg/cm 6kg/cm kg mm dB(A) m /min ft /min m/s2 5-12.5(3.7-9.2)
9mm
4300
4600
0.89
163
78
0.25
8.8
<2.5
6.5
9-18(6.6-13.3)
9mm
4300
4600
0.92
170
78
0.25
8.8
<2.5
6.5
12-26(8.8-19.2)
9mm
6800
7200
0.92
170
80
0.35
12.3
<2.5
6.5
18-30(13.3-22.1) 9mm
5900
6200
1.0
181
82
0.4
14.1
<2.5
8
9mm
4500
4800
1.08
192
82
0.43
15.2
<2.5
8
29-47(21.4-34.6) 9mm
6900
7200
1.35
197
82
0.45
15.9
<2.5
8
23-38(16.9-28)
★ Air Inlet：TDI(S)-30~150：NPT 1/4” TDI(S)-180：NPT 3/8” ★ Recommended Air Pressure：70~85 PSI(5 kg/cm2~6 kg/cm2) / 0.5MPa~ 0.6 MPa ★ Air Hose Size：10mm×6.5mm×5m for TDI(S)-30~50 12mm×8mm×5m for TDI(S)-60~100
Dimensions Model
d
b
φc φe
a
12
16mm×11mm×5m for TDI(S)-130~180
a (mm)
b (mm)
c (mm)
d (mm)
e (mm)
TDI(S)-30D
163
168
ø 46
21
ø 17.5
TDI(S)-40D
170
168
ø 46
27
ø 17.5
TDI(S)-50D
170
168
ø 46
27
ø 17.5
TDI(S)-60D
181
168
ø 46
27
ø 17.5
TDI(S)-65D
192
170
ø 47
28
ø 19
TDI(S)-70D
197
192
ø 53.5
28
ø 19
R
<Straight SQ. Drive>
Air Impulse Tools
TDI-30S TDIS-30S
TDI-40S TDIS-40S
TDI-50S TDIS-50S
TDI-60S TDIS-60S
TDI-70S• 80S TDIS-70S • 80S
Non shut-off Model
Torque Range N-m (ft-lb) 5-6kg/cm2
SQ Drive Bolt mm(“) Capacity
Free Speed
Weight Length
5kg/cm2 6kg/cm2
Noise Average Air Vibration Level Consumption Value Hose Size 3 3 dB(A) m /min ft /min m/s2
kg
mm
TDI-30S 9.5(3/8”)
M6
6-12.5(4.4-9.2)
3900
4200
0.8
221
78
0.25
8.8
2.6
6.5
TDI-40S 9.5(3/8”)
M6-M8
10-19(7.4-14)
3900
4200
0.8
221
78
0.25
8.8
2.9
6.5
TDI-50S 9.5(3/8”)
M8
13-27(9.6-19.9)
6500
6800
0.8
221
80
0.35
12.3
3
6.5
TDI-60S 9.5(3/8”)
M8-M10
20-35(14.7-25.8)
5700
6000
0.86
231
80
0.4
14.1
3.4
8
TDI-70S 9.5(3/8”)
M10
TDI-80S 9.5(3/8”) M10-M12
28-47(20.6-34.6)
4700
5000
0.97
244
80
0.4
14.1
3.7
8
40-70(29.5-51.5)
5800
6100
1.15
248
82
0.5
17.6
4
8
Auto shut-off Model
Torque Range N-m (ft-lb) 5-6kg/cm2
SQ Drive Bolt mm(“) Capacity
Free Speed
Weight Length
5kg/cm2 6kg/cm2
Noise Average Air Vibration Level Consumption Value Hose Size 3 3 dB(A) m /min ft /min m/s2
kg
mm
TDIS-30S 9.5(3/8”)
M6
6-12.5(4.4-9.2)
3900
4200
0.8
221
78
0.25
8.8
2.6
6.5
TDIS-40S 9.5(3/8”)
M6-M8
10-19(7.4-14)
3900
4200
0.8
221
78
0.25
8.8
2.9
6.5
TDIS-50S 9.5(3/8”)
M8
13-27(9.6-19.9)
6500
6800
0.8
221
80
0.35
12.3
3
6.5
TDIS-60S 9.5(3/8”)
M8-M10
20-35(14.7-25.8)
5700
6000
0.86
231
80
0.4
14.1
3.4
8
TDIS-70S 9.5(3/8”)
M10
28-47(20.6-34.6)
4700
5000
0.97
244
80
0.4
14.1
3.7
8
40-68(29.5-50)
5800
6100
1.15
248
82
0.5
17.6
4
8
TDIS-80S 9.5(3/8”) M10-M12
★ Air Inlet：TDI(S)-30~150：NPT 1/4” TDI(S)-180：NPT 3/8” ★ Recommended Air Pressure：70~85 PSI(5 kg/cm2~6 kg/cm2) / 0.5MPa~ 0.6 MPa ★ Air Hose Size：10mm×6.5mm×5m for TDI(S)-30~50 12mm×8mm×5m for TDI(S)-60~100
16mm×11mm×5m for TDI(S)-130~180
Dimensions Model
c
φ d
φ b
a
a (mm)
b (mm)
c (mm)
d (mm)
TDI(S)-30S
221
ø 46
24
ø 12
TDI(S)-40S
221
ø 46
24
ø 12
TDI(S)-50S
221
ø 46
24
ø 12
TDI(S)-60S
231
ø 46
24
ø 12
TDI(S)-70S
244
ø 48
25
ø 12
TDI(S)-80S
248
ø 48
25
ø 12
13
<Straight Bit Shank>
TDI-30SD TDIS-30SD
R
Air Impulse Tools
TDI-40SD TDIS-40SD
TDI-50SD TDIS-50SD
TDI-60SD TDIS-60SD
TDI-70SD TDIS-70SD
Non shut-off Model
Hex Size mm(“)
TDI-30SD 6.35Hex(1/4”)
Bolt Capacity M6
TDI-40SD 6.35Hex(1/4”) M6-M8 TDI-50SD 6.35Hex(1/4”)
M8
TDI-60SD 6.35Hex(1/4”)
M8
Noise Average Air Vibration Torque Range N-m Free Speed Weight Length Bit Level Consumption Value Hose (ft-lb) Size Shank 5-6kg/cm2 5kg/cm2 6kg/cm2 kg mm dB(A) m3/min ft3/min m/s2 5-11.5(3.7-8.4)
9mm
3900
4200
0.77
219
78
0.25
8.8
2.7
6.5
9-17(6.6-12.5)
9mm
3900
4200
0.8
224
78
0.25
8.8
3.1
6.5
12-25(8.8-18.4)
9mm
6500
6800
0.8
224
80
0.35
12.3
3.4
6.5
18-30(13.3-22.1) 9mm
5700
6000
0.86
235
80
0.4
14.1
3.8
8
TDI-70SD 6.35Hex(1/4”) M8-M10 25-40(18.4-29.4) 9mm
4700
5000
0.97
247
80
0.4
14.1
4.1
8
Auto shut-off Model
Hex Size mm(“)
TDIS-30SD 6.35Hex(1/4”)
Bolt Capacity M6
TDIS-40SD 6.35Hex(1/4”) M6-M8 TDIS-50SD 6.35Hex(1/4”)
M8
TDIS-60SD 6.35Hex(1/4”)
M8
Noise Average Air Vibration Torque Range N-m Free Speed Weight Length Bit Level Consumption Value Hose (ft-lb) Size Shank 2 2 2 3 3 5-6kg/cm 5kg/cm 6kg/cm kg mm dB(A) m /min ft /min m/s2 5-11.5(3.7-8.4)
9mm
3900
4200
0.77
219
78
0.25
8.8
2.7
6.5
9-17(6.6-12.5)
9mm
3900
4200
0.8
224
78
0.25
8.8
3.1
6.5
12-25(8.8-18.4)
9mm
6500
6800
0.8
224
80
0.35
12.3
3.4
6.5
18-30(13.3-22.1) 9mm
5700
6000
0.86
235
80
0.4
14.1
3.8
8
TDIS-70SD 6.35Hex(1/4”) M8-M10 25-40(18.4-29.4) 9mm
4700
5000
0.97
247
80
0.4
14.1
4.1
8
★ Air Inlet：TDI(S)-30~150：NPT 1/4” TDI(S)-180：NPT 3/8” ★ Recommended Air Pressure：70~85 PSI(5 kg/cm2~6 kg/cm2) / 0.5MPa~ 0.6 MPa ★ Air Hose Size：10mm×6.5mm×5m for TDI(S)-30~50 12mm×8mm×5m for TDI(S)-60~100
16mm×11mm×5m for TDI(S)-130~180
Dimensions
14
c
φ d
φ b
a
Model
a (mm)
b (mm)
c (mm)
d (mm)
TDI(S)-30SD
219
ø 46
21
ø 17.5
TDI(S)-40SD
224
ø 46
27
ø 17.5
TDI(S)-50SD
224
ø 46
27
ø 17.5
TDI(S)-60SD
235
ø 46
27
ø 17.5
TDI(S)-70SD
247
ø 48
28
ø 19
R
<Angle SQ. Drive>
Air Impulse Tools
TDI-50R TDIS-50R
TDI-60R TDIS-60R
TDI-70R TDIS-70R
TDI-70RG • 70RH• 80RH TDIS-70RG • 70RH• 80RH
H
Model
Model
SQ Drive Bolt mm(“) Capacity
W
Non shut-off
D
Torque Range N-m (ft-lb) 5-6kg/cm2
Free Speed 5kg/cm2 6kg/cm2
H(mm) W(mm) D(mm)
TDI(S)-50R.60R.70R
45
16
16
TDI(S)-70RG
47
18.5
21
TDI(S)-70RH.80RH
47
22.5
21
Weight Length
Noise Average Air Vibration Level Consumption Value Hose Size 3 3 dB(A) m /min ft /min m/s2
kg
mm
M6-M8
9.5-17(7-12.5)
4000
4300
1.2
253
80
0.32
11.3
16
6.5
9.5(3/8”)
M8
14-24(10.3-17.7)
4400
4700
1.3
264
80
0.4
14.1
16.8
8
9.5(3/8”)
M8-M10
20-31(14.7-22.8)
4200
4500
1.4
272
80
0.4
14.1
17.1
8
9.5(3/8”)
M10
TDI-50R
9.5(3/8”)
TDI-60R TDI-70R TDI-70RG
30-50(22.1-36.8)
1800
2000
1.6
281
82
0.4
14.1
17.4
8
TDI-70RH 12.7(1/2”) M10-M12
40-60(29.5-44.2)
2000
2200
1.6
281
82
0.4
14.1
17.4
8
TDI-80RH 12.7(1/2”) M10-M12
50-70(36.8-51.5)
2600
2800
1.7
281
82
0.45
15.9
19
8
Auto shut-off Model
SQ Drive Bolt mm(“) Capacity
Torque Range N-m (ft-lb) 5-6kg/cm2
Free Speed 5kg/cm2 6kg/cm2
Weight Length
Noise Average Air Vibration Level Consumption Value Hose Size 3 3 dB(A) m /min ft /min m/s2
kg
mm
TDIS-50R
9.5(3/8”)
M6-M8
9.5-17(7-12.5)
4000
4300
1.2
253
80
0.32
11.3
16
6.5
TDIS-60R
9.5(3/8”)
M8
14-24(10.3-17.7)
4400
4700
1.3
264
80
0.4
14.1
16.8
8
TDIS-70R
9.5(3/8”)
M8-M10
20-31(14.7-22.8)
4200
4500
1.4
272
80
0.4
14.1
17.1
8
TDIS-70RG 9.5(3/8”)
30-50(22.1-36.8)
1800
2000
1.6
281
82
0.4
14.1
17.4
8
TDIS-70RH 12.7(1/2”) M10-M12
M10
40-60(29.5-44.2)
2000
2200
1.6
281
82
0.4
14.1
17.4
8
TDIS-80RH 12.7(1/2”) M10-M12
50-70(36.8-51.5)
2600
2800
1.7
281
82
0.45
15.9
19
8
★ Air Inlet：TDI(S)-30~150：NPT 1/4” TDI(S)-180：NPT 3/8” ★ Recommended Air Pressure：70~85 PSI(5 kg/cm2~6 kg/cm2) / 0.5MPa~ 0.6 MPa ★ Air Hose Size：10mm×6.5mm×5m for TDI(S)-30~50 12mm×8mm×5m for TDI(S)-60~100
16mm×11mm×5m for TDI(S)-130~180
Dimensions Model
b
a
d
c
φe
a (mm)
b (mm)
c (mm)
d (mm)
e (mm)
TDI(S)-50R
253
45
14
16
ø 12
TDI(S)-60R
264
45
14
16
ø 12
TDI(S)-70R
272
45
14
16
ø 12
TDI(S)-70RG
281
47
18.5
21
ø 17
TDI(S)-70RH
281
47
22.5
21
ø 17
TDI(S)-80RH
281
47
22.5
21
ø 17
15
<Angle Bit Shank>
TDI-50RD TDIS-50RD
TDI-60RD TDIS-60RD
TDI-70RD TDIS-70RD
W
H
Model
Non shut-off Model
Hex Size mm(“)
R
Air Impulse Tools
Bolt Capacity
TDI-50RD 6.35Hex(1/4”) M6-M8
H(mm) W(mm) D(mm)
TDI(S)-50RD
45
16
16
TDI(S)-60RD
45
16
16
TDI(S)-70RD
45
16
16
D
Noise Average Air Vibration Torque Range N-m Free Speed Weight Length Bit Level Consumption Value Hose (ft-lb) Size Shank 5-6kg/cm2 5kg/cm2 6kg/cm2 kg mm dB(A) m3/min ft3/min m/s2 8.5-16(6.3-11.8)
9mm
4000
4300
1.2
253
80
0.32
11.3
16.5
6.5
TDI-60RD 6.35Hex(1/4”)
M8
12.5-22(9.2-16.2) 9mm
4400
4700
1.3
264
80
0.4
14.1
17.2
8
TDI-70RD 6.35Hex(1/4”)
M8
18-29(13.3-21.4) 9mm
4200
4500
1.4
272
80
0.4
14.1
17.5
8
Auto shut-off Model
Hex Size mm(“)
Bolt Capacity
TDIS-50RD 6.35Hex(1/4”) M6-M8
Noise Average Air Vibration Torque Range N-m Free Speed Weight Length Bit Level Consumption Value Hose (ft-lb) Size Shank 2 2 3 3 5-6kg/cm2 5kg/cm 6kg/cm kg mm dB(A) m /min ft /min m/s2 8.5-16(6.3-11.8)
9mm
4000
4300
1.2
253
80
0.32
11.3
16.5
6.5
TDIS-60RD 6.35Hex(1/4”)
M8
12.5-22(9.2-16.2) 9mm
4400
4700
1.3
264
80
0.4
14.1
17.2
8
TDIS-70RD 6.35Hex(1/4”)
M8
18-29(13.3-21.4) 9mm
4200
4500
1.4
272
80
0.4
14.1
17.5
8
★ Air Inlet：TDI(S)-30~150：NPT 1/4” TDI(S)-180：NPT 3/8” ★ Recommended Air Pressure：70~85 PSI(5 kg/cm2~6 kg/cm2) / 0.5MPa~ 0.6 MPa ★ Air Hose Size：10mm×6.5mm×5m for TDI(S)-30~50 12mm×8mm×5m for TDI(S)-60~100
Dimensions
φe
d
c
b
a
16
16mm×11mm×5m for TDI(S)-130~180
Model
a (mm)
b (mm)
c (mm)
d (mm)
e (mm)
TDI(S)-50RD
253
45
16
16
ø 11
TDI(S)-60RD
264
45
16
16
ø 11
TDI(S)-70RD
272
45
16
16
ø 11
R
<Sleeve Drive Sockets>
Air Impulse Tools
Sleeve Drive Sockets 3/4” Sleeve Drive Power Sockets Sleeve Drive Impact Sockets for ‧Maximum tool performance- reduces torque loss during pulsing stage. ‧Increase productivity- reduces time loss during pulsing stage. ‧Ensure worker safety- virtually no vibration to the operator. ‧Increase socket life- reduces wear on sockets. ‧Increase tool life- reduced vibration means minimal wear on your tool.
3/8” Sleeve Drive Power Sockets Order No. SS39006 SS39007 SS39008 SS39009 SS39010 SS39011 SS39012 SS39013 SS39014 SS39015 SS39016 SS39017 SS39018 SS39019 SS39020 SS39021 SS39022 SS39023 SS39024 SS39025 SS39026 SS39027
Size 6mm 7mm 8mm 9mm 10mm 11mm 12mm 13mm 14mm 15mm 16mm 17mm 18mm 19mm 20mm 21mm 22mm 23mm 24mm 25mm 26mm 27mm
D2 mm 19 19 19 19 19 19 19 22 22 22 22 22 22 22 22 22 23 23 23 23 23 23
D1 mm 11 12 13 15 16 17.5 18.5 20 21 22 24 25 26 27 28 30 31 32 34 35 36 38
L2 mm 5 5 7 7 7 8 9 9 9 12 12 12 12 12 13 13 14 14 15 15 15 15
L mm 43 43 43 43 43 43 43 43 43 43 43 43 43 43 43 43 50 50 50 50 50 50
1/2” Sleeve Drive Power Sockets Order No. SS49006 SS49007 SS49008 SS49009 SS49010 SS49011 SS49012 SS49013 SS49014 SS49015 SS49016 SS49017 SS49018 SS49019 SS49020 SS49021 SS49022 SS49023 SS49024 SS49025 SS49026 SS49027 SS49028 SS49029 SS49030 SS49031 SS49032 SS49033 SS49034 SS49035 SS49036 SS49038
Size 6mm 7mm 8mm 9mm 10mm 11mm 12mm 13mm 14mm 15mm 16mm 17mm 18mm 19mm 20mm 21mm 22mm 23mm 24mm 25mm 26mm 27mm 28mm 29mm 30mm 31mm 32mm 33mm 34mm 35mm 36mm 38mm
D2 mm 25 25 25 25 25 25 25 25 25 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 38
D1 mm 13 14 15 16 17.5 18.5 20 21 22.5 23.5 25 26 27.5 28.5 30 31 32 34 35 36 38 38.5 40 41 42 43 44 46 48 50 52 54
L2 mm 6 7 9 12 12 12 12 12 12 12 12 13 13 13 14 14 14 14 15 15 17 17 17 18 18 18 20 20 21 21 22 23
L mm 52 52 52 52 52 52 52 52 52 52 52 52 52 52 52 52 52 52 52 57 57 57 57 57 57 57 62 62 62 62 62 65
Order No. SS69013 SS69014 SS69015 SS69016 SS69017 SS69018 SS69019 SS69020 SS69021 SS69022 SS69023 SS69024 SS69025 SS69026 SS69027 SS69028 SS69029 SS69030 SS69031 SS69032 SS69033 SS69034 SS69035 SS69036 SS69037 SS69038 SS69039 SS69040 SS69041 SS69042 SS69043 SS69044 SS69045 SS69046 SS69047 SS69048 SS69049 SS69050 SS69051 SS69052 SS69053 SS69054 SS69055
Size 13mm 14mm 15mm 16mm 17mm 18mm 19mm 20mm 21mm 22mm 23mm 24mm 25mm 26mm 27mm 28mm 29mm 30mm 31mm 32mm 33mm 34mm 35mm 36mm 37mm 38mm 39mm 40mm 41mm 42mm 43mm 44mm 45mm 46mm 47mm 48mm 49mm 50mm 51mm 52mm 53mm 54mm 55mm
D2 mm 44 44 44 44 44 44 44 44 44 44 44 44 44 44 44 44 44 44 44 44 44 44 44 44 44 44 44 44 44 44 44 44 44 44 44 44 44 54 54 54 54 54 54
D1 mm 24.5 25.5 27 28 30 31 32 34 35 37 38 39 41 42 43 44 46 47 48 49 51 52 53 54 56 57 59 60 60 62 63.5 64.5 66 66.5 68 69 70 71 71 74 75 77 77
L2 mm 12 12 12 12 12 13 13 15 15 15 15 15 16 16 17 18 18 18 19 20 21 22 22 23 24 24 24 24 27 27 27 27 27 30 30 30 30 31 32 32 32 32 32
L mm 65 65 65 65 65 65 65 68 68 68 68 68 69 69 69 71 71 71 72 72 73 73 73 73 73 75 75 75 75 75 75 75 75 80 80 80 80 80 85 85 85 85 85
Impulse Oil (100ml) Use only the authorized impulse oil with the tools.The authorized oil is made by unique and special formulations. Any unauthorized oil will damage or degrade the performance of the tools. We recommend to change the impulse oil after every 250,000 pulseseconds. Please cantact the authorized agentent for oil purchasing.
17
INDUSTRIAL POWER TOOLS
Shut-off 18
R
Air Industrial Screwdrivers
TDCS Selection Chart BOLT GRADE at 8.8
A i r Industrial Screwdriver
M2
M3
M4
M5
M6
PISTOL TYPE T D CS-0815 T D CS-0811 T D CS-1016 T D CS-1009 T D CS-2017 T D CS-2011 T D CS-2007 T D CS-3017 T D CS-3011 T D CS-3007 T D CS-3005 PUSH START T D CS-08S15 T D CS-08S11 T D CS-10S16 T D CS-10S09 T D CS-20S17 T D CS-20S11 T D CS-20S07 T D CS-30S17 T D CS-30S11 T D CS-30S07 T D CS-30S05 LEVER START T D CS-08SL15 T D CS-08SL11 T D CS-10SL16 T D CS-10SL09 T D CS-20SL17 T D CS-20SL11 T D CS-20SL07 T D CS-30SL17 T D CS-30SL11 T D CS-30SL07 T D CS-30SL05 ANGLE TYPE T D CS-08R15 T D CS-08R11 T D CS-10R16 T D CS-10R09 T D CS-20R17 T D CS-20R11 T D CS-20R07 T D CS-30R17 T D CS-30R11 T D CS-30R07 T D CS-30R05
0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9
1
1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9
To r q u e ( N . m )
2
3
4
5
6
7
8
9
10
11
12
TORQUE RANGE REFERENCE Torque is a very important reference value while choosing a right tool for tightening. Due to the actual tighten torque may vary because of nut sizes, joint types, air pressure and working environment, the above table is only for a reference to choose a right tool. When the working torque is at the mean value of the torque range, the tool provides the best performance.
Torque Conversion N-m 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 1.1 1.2
kg-cm 1.02 2.04 3.06 4.08 5.10 6.12 7.14 8.16 9.18 10.20 11.22 12.24
in-lbs 0.89 1.77 2.66 3.54 4.43 5.31 6.20 7.08 7.97 8.85 9.74 10.62
N-m 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2 3 4 5 6
kg-cm 13.26 14.28 15.30 16.32 17.34 18.35 19.37 20.39 30.59 40.79 50.99 61.18
in-lbs 11.51 12.39 13.28 14.16 15.05 15.93 16.82 17.70 26.55 35.40 44.25 53.10
N-m 7 8 9 10 11 12 13 14 15 16 17 18
kg-cm 71.38 81.58 91.77 101.97 112.17 122.37 132.56 142.76 152.96 163.16 173.35 183.55
in-lbs 61.95 70.81 79.66 88.51 97.36 106.21 115.06 123.91 132.76 141.61 150.46 159.31
19
Two Choices for Air Inlet
Accurate Shut off System
Gravity Casting Housing for High Durabilty
Fine Clutch and motor prolonging tool life
Precise Machining Alloy Steel Gear
Color Tapered Cap For Better Visibility and Management
Easy Torque Adjustment
One hand reverse operation for right or left handed operators
Handle Rubber Injection: designed ergonomically for comfortable operation. 360째 revolving Low Noise Exhaust Device
20
R
<Pistol Type>
Air Industrial Screwdrivers
TDCS-10
TDCS-08
TDCS-20 TDCS-30
SPECIFICATIONS Model
Screw Size (mm)
Torque Range in-lb
Nm
Free Bit Speed Shank rpm
Weight
Drive Size Dia Air Inlet
kg
lb
inch
inch
inch
Average Air Consumption m3/min ft3/min
Noise Level dB(A)
Vibration Value m/s2
TDCS-0815
M2
2.7~7
0.3~0.8
9mm
1500
0.7
1.5
1/4 F/Hex
0.9
1/4
0.2
7
72
<2.5
TDCS-0811
M2
2.7~8.8
0.3~1
9mm
1100
0.7
1.5
1/4 F/Hex
0.9
1/4
0.2
7
72
<2.5
TDCS-1016 M2-M3 6.2~12.3 0.7~1.3
9mm
1600
0.9 1.98 1/4 F/Hex
1.1
1/4
0.35
12.5
75
<2.5
TDCS-1009
M3
6.2~17.6
0.7~2
9mm
900
0.9 1.98 1/4 F/Hex
1.1
1/4
0.35
12.5
75
<2.5
TDCS-2017
M3
8.8~25
1~2.8
9mm
1700 1.15 2.53 1/4 F/Hex 1.37
1/4
0.47
16.5
78
<2.5
TDCS-2011
M3-M4
8.8~30
1~3.4
9mm
1100 1.15 2.53 1/4 F/Hex 1.37
1/4
0.47
16.5
78
<2.5
TDCS-2007 M3-M4
8.8~40
1~4.5
9mm
700
1.15 2.53 1/4 F/Hex 1.37
1/4
0.47
16.5
78
<2.5
17.6~39.6
2~4.5
9mm
1700
1.2 2.64 1/4 F/Hex 1.37
1/4
0.51
18
78
<2.5
3~6
9mm
1100
1.2 2.64 1/4 F/Hex 1.37
1/4
0.51
18
78
<2.5
3~8
TDCS-3017 TDCS-3011
M4
M4-M5 26.4~52.8
TDCS-3007
M5
26.4~70
9mm
700
1.2 2.64 1/4 F/Hex 1.37
1/4
0.51
18
78
<2.5
TDCS-3005
M6
39.6~96 4.5~10.9 9mm
500
1.2 2.64 1/4 F/Hex 1.37
1/4
0.51
18
78
<2.5
★ Recommended Air Pressure：TDCS-08.10：70psi (5kg/cm2)/0.5MPa TDCS-20.30：85psi (6kg/cm2)/0.6MPa ★ Air Hose Size：10mm×6.5mm×5m a
φe
Pistol Type
c
e
b
d
d
Model
a (mm)
b (mm)
c (mm)
d (mm)
e (mm)
TDCS-08
214.3
162.3
143.8
11.7
ø 12.6
TDCS-10
209.1
162.3
143.8
13
ø 12.6
TDCS-20
227.8
164.5
143.3
10.6
ø 12.6
TDCS-30
230
164.5
143.3
10.6
ø 12.6
21
<Push Start>
R
Air Industrial Screwdrivers
TDCS-08S
TDCS-10S
TDCS-20S
TDCS-30S
SPECIFICATIONS Model
Screw Size (mm)
TDCS-08S15 TDCS-08S11
Torque Range
Free Bit Speed Shank rpm
Nm
M2
2.7~7
0.3~0.8
9mm
M2
2.7~8.8
0.3~1
lb
inch
Average Air Consumption m3/min ft3/min
Noise Level dB(A)
Vibration Value m/s2
inch
1500 0.35 0.77 1/4 F/Hex
0.9
1/8
0.2
7
73
<2.5
9mm
1100 0.35 0.77 1/4 F/Hex
0.9
1/8
0.2
7
73
<2.5
TDCS-10S16 M2-M3 6.2~12.3 0.7~1.3
9mm
1600
0.6 1.32 1/4 F/Hex
1.1
1/8
0.35
12.5
75
<2.5
TDCS-10S09
M3
6.2~17.6
0.7~2
9mm
900
0.6 1.32 1/4 F/Hex
1.1
1/8
0.35
12.5
75
<2.5
TDCS-20S17
M3
8.8~25
1~2.8
9mm
1700
0.9 1.98 1/4 F/Hex 1.37
1/4
0.47
16.5
78
<2.5
TDCS-20S11 M3-M4
8.8~30
1~3.4
9mm
1100
0.9 1.98 1/4 F/Hex 1.37
1/4
0.47
16.5
78
<2.5
TDCS-20S07 M3-M4
8.8~40
1~4.5
9mm
700
0.9 1.98 1/4 F/Hex 1.37
1/4
0.47
16.5
78
<2.5
17.6~39.6
2~4.5
9mm
1700 0.97 2.13 1/4 F/Hex 1.37
1/4
0.51
18
78
<2.5
TDCS-30S11 M4-M5 26.4~52.8
3~6
9mm
1100 0.97 2.13 1/4 F/Hex 1.37
1/4
0.51
18
78
<2.5
TDCS-30S07
M5
26.4~70
3~8
9mm
700
0.97 2.13 1/4 F/Hex 1.37
1/4
0.51
18
78
<2.5
TDCS-30S05
M6
39.6~96 4.5~10.9 9mm
500
0.97 2.13 1/4 F/Hex 1.37
1/4
0.51
18
78
<2.5
M4
kg
Drive Size Dia Air Inlet inch
TDCS-30S17
in-lb
Weight
★ Recommended Air Pressure：TDCS-08.10：70psi (5kg/cm2)/0.5MPa TDCS-20.30：85psi (6kg/cm2)/0.6MPa ★ Air Hose Size：10mm×6.5mm×5m
b φ
Push Start Type
a
d φ
22
c
Model
a (mm)
b (mm)
c (mm)
d (mm)
TDCS-08S
216.1
ø 37.4
12.1
ø 12.6
TDCS-10S
229.1
ø 43.4
13.7
ø 12.6
TDCS-20S
254
ø 49
11.8
ø 12.6
TDCS-30S
258
ø 53
12.1
ø 12.6
R
<Lever Start>
Air Industrial Screwdrivers
TDCS-08SL
TDCS-10SL
TDCS-20SL
TDCS-30SL
SPECIFICATIONS Model
Screw Size (mm)
TDCS-08SL15 TDCS-08SL11
Torque Range Nm
M2
2.7~7
0.3~0.8
M2
2.7~8.8
0.3~1
Weight lb
inch
Average Air Consumption m3/min ft3/min
Noise Level dB(A)
Vibration Value m/s2
inch
9mm
1500 0.41 0.9 1/4 F/Hex 0.9
1/8
0.2
7
73
<2.5
9mm
1100 0.41 0.9 1/4 F/Hex 0.9
1/8
0.2
7
73
<2.5
TDCS-10SL16 M2-M3 6.2~12.3 0.7~1.3
9mm
1600 0.63 1.4 1/4 F/Hex 1.1
1/8
0.35
12.5
75
<2.5
TDCS-10SL09
M3
6.2~17.6
0.7~2
9mm
900
1/8
0.35
12.5
75
<2.5
TDCS-20SL17
M3
8.8~25
1~2.8
9mm
1700
1
2.2 1/4 F/Hex 1.37
1/4
0.47
16.5
78
<2.5
TDCS-20SL11 M3-M4
8.8~30
1~3.4
9mm
1100
1
2.2 1/4 F/Hex 1.37
1/4
0.47
16.5
78
<2.5
TDCS-20SL07 M3-M4
8.8~40
1~4.5
9mm
700
1
2.2 1/4 F/Hex 1.37
1/4
0.47
16.5
78
<2.5
17.6~39.6
2~4.5
9mm
1700
1
2.2 1/4 F/Hex 1.37
1/4
0.51
18
78
<2.5
TDCS-30SL11 M4-M5 26.4~52.8
3~6
9mm
1100
1
2.2 1/4 F/Hex 1.37
1/4
0.51
18
78
<2.5
TDCS-30SL07
M5
26.4~70
3~8
9mm
700
1
2.2 1/4 F/Hex 1.37
1/4
0.51
18
78
<2.5
TDCS-30SL05
M6
39.6~96 4.5~10.9 9mm
500
1
2.2 1/4 F/Hex 1.37
1/4
0.51
18
78
<2.5
M4
kg
Drive Size Dia Air Inlet inch
TDCS-30SL17
in-lb
Free Bit Speed Shank rpm
0.63 1.4 1/4 F/Hex 1.1
★ Recommended Air Pressure：TDCS-08.10：70psi (5kg/cm2)/0.5MPa TDCS-20.30：85psi (6kg/cm2)/0.6MPa ★ Air Hose Size：10mm×6.5mm×5m
b φ
Lever Start Type
a
d φ
Model
a (mm)
b (mm)
c (mm)
d (mm)
TDCS-08SL
235.8
ø 37.4
11.7
ø 12.6
TDCS-10SL
244.2
ø 43.4
13.7
ø 12.6
TDCS-20SL
274
ø 49
11.1
ø 12.6
TDCS-30SL
271.7
ø 53
12.1
ø 12.6
c
23
<Angle Type>
R
Air Industrial Screwdrivers
TDCS-08R
TDCS-10R
TDCS-20R
TDCS-30R
SPECIFICATIONS Model
Screw Size (mm)
TDCS-08R15 TDCS-08R11
Torque Range
Free Bit Speed Shank rpm
Nm
M2
2.7~7
0.3~0.8
9mm
M2
2.7~8.8
0.3~1
inch
Noise Level dB(A)
Vibration Value m/s2
1500 0.56 1.23 1/4 F/Hex
0.9
1/8
0.2
7
73
<2.5
9mm
1100 0.56 1.23 1/4 F/Hex
0.9
1/8
0.2
7
73
<2.5
TDCS-10R16 M2-M3 6.2~12.3 0.7~1.3
9mm
1600
0.8
1.8
1/4 F/Hex
1.1
1/8
0.35
12.5
75
<2.5
TDCS-10R09
M3
6.2~17.6
0.7~2
9mm
900
0.8
1.8
1/4 F/Hex
1.1
1/8
0.35
12.5
75
<2.5
TDCS-20R17
M3
8.8~25
1~2.8
9mm
1700
1.2 2.64 1/4 F/Hex 1.37
1/4
0.47
16.5
78
<2.5
TDCS-20R11 M3-M4
8.8~30
1~3.4
9mm
1100
1.2 2.64 1/4 F/Hex 1.37
1/4
0.47
16.5
78
<2.5
TDCS-20R07 M3-M4
8.8~40
1~4.5
9mm
700
1.2 2.64 1/4 F/Hex 1.37
1/4
0.47
16.5
78
<2.5
9mm
1700
1.3 2.86 1/4 F/Hex 1.37
1/4
0.51
18
78
<2.5
21.2~39.6 2.5~4.5
lb
Average Air Consumption m3/min ft3/min
inch
M4
kg
Drive Size Dia Air Inlet inch
TDCS-30R17
in-lb
Weight
TDCS-30R11 M4-M5 35.2~52.8
4~6
9mm
1100
1.3 2.86 1/4 F/Hex 1.37
1/4
0.51
18
78
<2.5
TDCS-30R07
M5
35.2~70
4~8
9mm
700
1.3 2.86 1/4 F/Hex 1.37
1/4
0.51
18
78
<2.5
TDCS-30R05
M6
44~96
5~10.9
9mm
450
1.3 2.86 1/4 F/Hex 1.37
1/4
0.51
18
78
<2.5
★ Recommended Air Pressure：TDCS-08.10：70psi (5kg/cm2)/0.5MPa TDCS-20.30：85psi (6kg/cm2)/0.6MPa ★ Air Hose Size：10mm×6.5mm×5m
c
b
Angle Type
e
24
φ f
a
φ d
Model
a (mm)
b (mm)
c (mm)
d (mm)
e (mm)
f (mm)
TDCS-08R
284.1
12
29
ø 24
12
ø 11
TDCS-10R
290.5
12
29
ø 24
12
ø 11
TDCS-20R
320.6
12
29
ø 24
12
ø 11
TDCS-30R
328
12.7
30
ø 27
13.5
ø 11
INDUSTRIAL POWER TOOLS
Cordless 25
R
Industrial Cordless Tools
Tool Selection Chart
Torque Range Reference Torque is a very important reference value while choosing a right tool for tightening. Due to the actual tighten torque may vary because of nut sizes, joint types and working environment, the above table is only for a reference to choose a right tool. When the torque is at the mean value of the torque range, the tool provides the best performance.
Tightening Torque (N.m) This table shows the recommended tightening torque for common bolt size M2 to M16. According to ISO 898-1 Bolt Size mm M2 M3 M4 M5 M6
3.6 0.10 0.35 0.81 1.60 2.80
4.6 0.13 0.46 1.10 2.20 3.70
4.8 0.17 0.61 1.40 2.95 4.90
Bolt Grade 5.8 8.8 0.22 0.35 0.77 1.20 1.80 2.90 3.60 5.70 6.10 9.80
10.9 0.49 1.70 4.00 8.10 14.0
12.9 0.58 2.10 4.90 9.70 17.0
Bolt Size mm M8 M10 M12 M14 M16
4.6 8.9 17 30 48 74
4.8 10.5 21 36 58 88
Bolt Grade 5.8 8.8 15 24 29 47 51 81 80 128 123 197
N.m 6 7 8 9 10 11 12 13
kg-cm 61.18 71.38 81.58 91.77 101.97 112.17 122.37 132.56
10.9 33 65 114 181 277
12.9 40 79 136 217 333
Torque Conversion N.m 0.8 0.9 1 1.1 1.2 1.3 1.4 1.5
26
kg-cm 8.16 9.18 10.20 11.22 12.24 13.26 14.28 15.30
in-lbs 7.08 7.97 8.85 9.74 10.62 11.51 12.39 13.28
N.m 1.6 1.7 1.8 1.9 2 3 4 5
kg-cm 16.32 17.34 18.35 19.37 20.39 30.59 40.79 50.99
in-lbs 14.16 15.05 15.93 16.82 17.70 26.55 35.40 44.25
in-lbs 53.10 61.95 70.81 79.66 88.51 97.36 106.21 115.06
R
<SCB series>
Industrial Cordless Tools
Programmer (One programmer fits all SCB series tools) Increase tool speed
Decrease tool speed
● Easy to set the tool speed. 1.High speed for metallic assemblies. 2.Medium speed for plastic assemblies. 3.Low speed for special assemblies.
● Total used time display function.
● Total operation count display function.
● Trip operation count display function.
27
<SCB series>
Industrial Cordless Tools
Cordless Shut-off Screwdriver SCB series
User can distinguish the torque at a glance of color.
( Brushless motor )
LED light for working in dark area.
Trigger repeat protection avoid double hits on already seated screw.
Easy attached sliding battery system.
Soft grip handle reduces vibration and fatigue.
High capacity Li-ion battery pack delivers longer run-time.
Mini USB Connector: Tool speed can be adjusted by the extra programmer.
When the arrow mark is blue, it means the tool is in the reverse operation. A green light tells the operator that the preset torque is reached and the tightening is OK.
Touch switch for F/R operation.
A red light and one long "beep" sound tell the operator that the preset torque is not reached,the screwing fastener must be performed again. A flashing yellow light and five short "beep" sounds give an early warning when it is time for recharging.
LED indicator provides simple process information to the operator. The signal is visible from any angle.
28
A yellow light and one long "beep" sound mean a battery lock that indicates the tool can't work and MUST change the battery pack immediately.
R
R
<SCB series>
Industrial Cordless Tools
Advanced brushless motor.
Precise alloy steel gear for high durability.
Torque adjustment.
Precision clutch for torque accuracy.
(Beep Tone)
APPLICATIONS ● Assembly applications where torque accuracy is required. ● Areas where pneumatic or electric tools are impractical to use due to hoses/cables. ● Especially used on car interior assembly. ● Attaching components to the dashboard. ● Hose clips on turbo chargers and air intakes,heating and climate systems and coolant circuits.
PRODUCT STRENGTHS ● Adopting with the innovative Lithium-ion battery technology that extends the operating time of one full charged battery to be longer than the Ni-Cad and the Ni-MH battery. ● Lithium-ion battery has no memory effect which extends the cycle life of the battery. ● The unique design of low battery warning that reminds operators the time to change the battery. ● Brushless motor has longer life time and wear free for low maintenance and spare part costs. ● Tool speed can be adjusted for different applications. ● Soft grip handle reduces vibration and fatigue. ● Torque accuracy : Meet ISO 5393 Cmk>2 at ± 10% tolerance
SPECIFICATIONS Model
Volt.
Drive Size
Screw Size
Torque Range
Free Speed
V
in
mm
N.m（ft-lb）
rpm
Weight w/o Batt. kg
Vibration Value
Noise Level
m/s2
dB(A)
High speed for short cycle times
<2.5
<75
<2.5
<75
<2.5
<75
<2.5
<75
Application
lb
SC180BBS3
18
1/4” Hex. M3~M4
0.8~3 ( 0.6~2.2 )
500~1,550 0.95 2.1
SC180BBS6
18
1/4” Hex. M3~M5
1~6 ( 0.7~4.4 )
300~900
0.95 2.1 Special for hose clip
SC180BBS9
18
1/4” Hex. M3~M5
1.5~9 ( 1.1~6.6 )
300~700
0.95 2.1
SC180BBS12
18
1/4” Hex. M4~M6
2~12 ( 1.5~9 )
250~550
0.95 2.1 Broad torque range
Combination of speed and torque
★ Adjustment screwdriver , suspension bail , marking color ring are included with the tool.
29
<SC series>
Industrial Cordless Tools
Cordless Shut-off Screwdriver SC series
( Brush motor )
LED light for working in dark area.
Press button for easy Forward/ Reverse operation.
Trigger repeat protection avoid double hits on already seated screw. Ergonomical handle design provides a well-balance.
Easy attached sliding battery system.
High capacity 3.0 A.h Li-ion battery pack delivers longer run-time.
LED indicator provides simple process information to the operator.
A green light tells the operator that the preset torque is reached and the tightening is OK. A red light and one long "beep" sound tell the operator that the preset torque is not reached,the screwing fastener must be performed again. A flashing yellow light and five short "beep" sounds give an early warning when it is time for recharging. A yellow light and one long "beep" sound mean a battery lock that indicates the tool can't work and MUST change the battery pack immediately.
APPLICATIONS ● Assembly applications where torque accuracy is required. ● Areas where pneumatic or electric tools are impractical to use due to hoses/cables. ● Especially used on car interior assembly. ● Attaching components to the dashboard. ● Hose clips on turbo chargers and air intakes,heating and climate systems and coolant circuits.
PRODUCT STRENGTHS ● Adopting with the innovative Lithium-ion battery technology that extends the operating time of one full charged battery to be longer than the Ni-Cad and the Ni-MH battery. ● Lithium-ion battery has no memory effect which extends the cycle life of the battery. ● The unique design of low battery warning that reminds operators the time to change the battery. ● The ergonomic handle design makes work easier and effort-saving that promotes the work efficiency. ● Torque accuracy : Meet ISO 5393 Cmk>2 at ± 10% tolerance 30
R
R
<SC series>
Industrial Cordless Tools
High performance brush motor.
Precise alloy steel gear for high durability.
Torque adjustment
Precision clutch for torque accuracy.
Precision IC board control.
(Beep Tone)
SPECIFICATIONS Model
Volt.
Drive Size
Screw Size
Torque Range
V
in
mm
N.m（ft-lb）
Free Weight Speed w/o Batt. rpm
kg
Application
lb
Vibration Value
Noise Level
m/s2
dB(A)
<2.5
<75
<2.5
<75
<2.5
<75
<2.5
<75
SC108BS3L
10.8
1/4” Hex. M3~M4 1~3.5 ( 0.7~2.6 ) 1,100
1.0
High speed for short cycle 2.2 times
SC108BS5B
10.8
1/4” Hex. M3~M5 1~5.5 ( 0.7~4.1 )
170
1.0
2.2 Special for hose clip
SC108BS8I
10.8
1/4” Hex. M4~M5
2~8 ( 1.5~5.9 )
800
1.0
SC108BS11F
10.8
1/4” Hex. M4~M6 3~11 ( 2.2~8.1 )
500
1.0
SC108BS12D 10.8
1/4” Hex. M4~M6
4~12 ( 3~9 )
300
1.0
2.2 Special for heavy soft joint
<2.5
<75
SC108BS12B 10.8
1/4” Hex. M4~M6
4~12 ( 3~9 )
170
1.0
2.2 Special for heavy soft joint
<2.5
<75
SC108BS12E 10.8
1/4” Hex. M3~M6 1.5~12 ( 1.1~9 )
470
1.0
<2.5
<75
SC108BS12Z 10.8
1/4” Hex. M3~M6 1.5~12 ( 1.1~9 )
380
1.0
<2.5
<75
Combination of speed and torque Combination of speed and 2.2 torque 2.2
Broad torque range and special for medium soft joint Broad torque range and 2.2 special for heavy soft joint 2.2
★ Adjustment screwdriver is included with the tool.
31
<WR series>
Industrial Cordless Tools
Cordless Shut-off Angle Wrench/Screwdriver WR series
( Brushless motor )
10.8V/14.4V High capacity 3.0 A.h Li-ion battery pack delivers longer run-time.
Ergonomical handle design provides a well-balance.
User can distinguish the torque at a glance of color.
LED light for working in dark area.
Press button for easy Forward/Reverse operation.
Trigger repeat protection avoid double hits on already seated screw.
The angled head allowing multiple head positions.
A green light tells the operator that the preset torque is reached and the tightening is OK. A red light and one long "beep" sound tell the operator that the preset torque is not reached,the screwing fastener must be performed again. A flashing yellow light and five short "beep" sounds give an early warning when it is time for recharging. A yellow light and one long "beep" sound mean a battery lock that indicates the tool cannot work and MUST change the battery pack immediately. LED indicator provides simple process information to the operator.
APPLICATIONS ● Assembly applications where torque accuracy is required. ● Areas where pneumatic or electric tools are impractical to use due to hoses/cables. ● Especially used in cramped spaces.
PRODUCT STRENGTHS ● The high performance brushless motor reduces the harm of environment and provides more fastening cycles per battery charge. ● To use innovative 3.0A.h Li-ion battery makes working time longer than Ni-Cad and Ni-MH batteries. ● Li-ion battery without memory effect so the battery life can be last longer. ● The common use 30 N.m tool is lighter and shorter than other brands , it makes the operation much easier and less fatigue. ● Torque accuracy : Meet ISO 5393 Cmk>2 at ±10% tolerance 32
R
R
<WR series>
Industrial Cordless Tools
Advanced brushless motor.
(Beep Tone)
Precision IC board control.
Precision clutch for torque accuracy.
Torque adjustment.
Precise alloy steel gear for high durability.
H (mm)
W (mm)
D (mm)
3/8" Sq.
39
12
16
1/4" Sq.
39
9
16
1/4" Hex.
39
20
16
455
Drive Type
SPECIFICATIONS Model
WR108BAS8I
114
Volt.
Drive Size
Screw Size
Torque Range
V
in
mm
N.m（ft-lb）
rpm
kg
M4~M5
2~8 ( 1.5~5.9 )
850
1.3 2.86
M5~M6
5~16 ( 3.7~11.8 )
330
1.3 2.86
Vibration Value
Noise Level
m/s2
dB(A)
High speed for short cycle times
2.63
<75
Combination of speed and torque
2.63
<75
2.55
<75
2.55
<75
Free Weight Speed w/o Batt.
Application
lb
10.8 1/4” Hex.
WR108B2AS8I
10.8
1/4” Sq.
WR108B3AS8I
10.8
3/8” Sq.
WR108BAS16D
10.8 1/4” Hex.
WR108B2AS16D 10.8
1/4” Sq.
WR108B3AS16D 10.8
3/8” Sq.
WR144B3AS30E 14.4
3/8” Sq.
M6~M8
8~30 ( 5.9~22.1 )
400
WR144B3AS30C 14.4
3/8” Sq.
M6~M8
8~30 ( 5.9~22.1 )
250
High torque and special for medium soft joint High torque and special 1.3 2.86 for heavy soft joint 1.3 2.86
★ Adjustment screwdriver , spanner , suspension bail , marking color ring are included with the tool.
33
<Accessories>
R
Industrial Cordless Tools
Accessories Li-ion Battery Pack
BB108BN-330 Part No. BB108BN-330 BB144BN-330 BB180BN-315 BB180BN-330
BB144BN-330 Description 10.8 V 3.0 A.h 14.4 V 3.0 A.h 18 V 1.5 A.h 18 V 3.0 A.h
B84192B
B84192B
Description Input:100~240 VAC Output:10.8~14.4 VDC for Ni-MH＆Li-ion Input:100~240 VAC Output:18~19.2 VDC for Ni-MH＆Li-ion
E86B-UL Weight 0.51 kg (1.12 lb)
0.51 kg (1.12 lb)
Marking color ring (suit to WR series)
000-4120R
000-4120W
Part No. 000-4120R 000-4120W 000-4120Y
000-4120Y Description Red White Yellow
Angle head ass'y (suit to WR series)
B42WR108B Part No. B42WR108B B42WR108B2 B42WR108B3
34
Charger Time 65 min. 65 min. 40 min. 65 min.
0.49 0.60 0.42 0.71
Weight kg (1.07 kg (1.32 kg (0.92 kg (1.56
lb) lb) lb) lb)
Power cord (for charger use)
B84B
B84B
BB180BN-330
Size（L × W × H） 93 × 78 × 70 mm 108 × 78 × 70 mm 93 × 78 × 70 mm 127 × 78 × 70 mm
Charger
Part No.
BB180BN-315
B42WR108B2
B42WR108B3 Description 1/4” Hex. 1/4” Sq. 3/8” Sq.
E86B-VD
E86B-AS
E86B-UK
Part No.
Description
Weight
E86B-UL
for USA region
62 g (0.13 lb)
E86B-VD
for Europe region
79 g (0.17 lb)
E86B-AS
for Australia region
105 g (0.23 lb)
E86B-UK
for England region
151 g (0.33 lb)
Marking color ring (suit to SCB series)
000-4121B
000-4121R
Part No. 000-4121B 000-4121R 000-4121W 000-4121Y
000-4121W
000-4121Y
Description Blue Red White Yellow
Angle head adapter (suit to WR series)
B55WR108B Part No. B55WR108B B55WR108B-1
B55WR108B-1 Description Length : 2” Length : 4”
R
<Accessories>
Industrial Cordless Tools
Programmer Setting the tool speed.
Shoulder strap
Part No. : B74SC180B ( suit to SCB series )
Part No. : D37SC108B-2 ( suit to SC series )
● Please see the instruction manual.
Adjustment screwdriver
Spanner Part No. : D34WR108B ( suit to WR series )
Part No. : D57SC108B-1 ( suit to all series )
Suspension bail To suspend the tool on a balancer. Part No. : D39WR108B-6 ( suit to WR series )
Part No. : D39SC180B-1 ( suit to SCB series )
Tool cover To avoid damaging the workpiece surface. Part No. : C16SC108B ( suit to SC series )
Part No. : C16SC180B ( suit to SCB series )
Part No. : C16WR108B ( suit to WR series )
35
Cordless 36
INDUSTRIAL POWER TOOLS
Impact 37
Precise Ductile Cast Iron Cylinder gives better wear resistance.
Oil Bathed Impact Mechanism Extends the life of impact mechanism more than 1 time longer of tools.
SR impact mechanism extends the life of impact mechanism 1 time longer. Patents in EU, USA, JPN and Taiwan.
38
Impact
Composite
R
<SQ. Drive Type>
Air Impulse Tools
Composite Housing for Aviatic applications durable and light weight. Not easy to break. Much more strenghten.
Unique Air Channel Design: increases the efďŹ ciency of air inletting and exhausting that deďŹ nitely gives a better performance of tools.Patents in EU, USA, JPN and Taiwan.
Front and Rear End Plates with Alloy Steel Plates added reduce Repair Bills and easy on maintenance.
Composite Blades for Aviatic applications provide good stability and not be affected by humidity.
Handle Rubber Injection: designs ergonomically and provides a comfortable operation.
39 39
R
Air Industrial Impact Wrench
TDW-278V
Model
TDW-305V
SQ Drive Bolt Size (in) (mm)
TDW-243V TDW-243V-4
Nm
Ft-lbs
Kgm
Average Air Net Free Weight Speed Consumption Nm Ft-lbs Kgm Kg (lbs) (rpm) m3/min ft3/min
Working Torque
Max Torque
TDW-243V
3/8”
M12
78-275
57-203
8-28
380
280
39
TDW-243V-4
1/2”
M14
98-294
73-217
10-30
407
300
41
TDW-305V
1/2”
M16
294-490 217-361 30-50
949
700
97
TDW-278V
3/4”
M22
441-883 325-651 45-90 1898 1400
193
1.3 (2.8) 1.3 (2.8) 2.1 (4.6) 3.8 (8.3)
Noise Level
Vibration Value
dB(A)
m/s2
9,500
0.54
19.07
89
3.4
9,500
0.54
19.07
89
3.4
7,000
0.61
21.54
90
3.4
4,000
0.7
24.72
90
3.5
★ Recommended Air Pressure：90 PSI(6.3 kg/cm2) ★ Air Hose Size：16mm×11mm×5m
B
A
Impact 40
Composite
Model
A(mm)
B(mm)
TDW-243V(-4)
173
180
TDW-305V
198
200
TDW-278V
244
225
R
Digital Torque Wrench
Quick change
Press To Release
Reversal Lever
Large LCD
Soft Button (One-button One-function)
Buzzer (Beep Tone)
Square
Alarm LED
Advanced CPU
Ergonomics Handle 41
R
Digital Torque Wrench
ISO 17025 Every torque wrench in DTW series is tested in the Calibration Lab. that is complied with the ISO: 17025.
Every torque wrench in DTW series is complied with ISO:6789 and must pass 100% strict quality inspection and test.
Calibration Laboratory The Calibration Lab. is one of the members of Taiwan Accreditation Foundation (TAF).
GRAVITY
It is more precise to make the calibration in the Calibration Lab. after measuring the gravity by Taiwan National Science Council.
THE CALIBRATION MACHINE Every torque wrench has been approved by t h e C a l i b r a t i o n Lab. A nd the test report is International valid, which is granted by the laboratories in numerous countries.
42
Model
SQ.Drive
DTW-3135
3/8”
DTW-4135
Nm
Ft-lbs
Length Weight (mm) (kg)
In-lbs
Kgm
10-135 7.4-99.6
89-1198
1-13.7
400
1.2
1/2”
10-135 7.4-99.6
89-1198
1-13.7
400
1.2
DTW-3200
3/8”
20-200 14.8-147 178-1780 2-20.4
570
1.6
DTW-4200
1/2”
20-200 14.8-147 178-1780 2-20.4
570
1.6
DTW-4340
1/2”
34-340 25-250.9 303-3010 3.5-34.7 770
2
Accuracy
CW±2％+1 LSD/CCW±3％+1 LSD
Direction
Clockwise/Counter-clockwise
Torque Unit
Nm/Ft-lbs/In-lbs/Kgm
Battery
9V(Alkaline)×1
Operation Temperature
5~ 42℃,40~ 107℉
Storage Temperature
-20~ 50℃,-4~ 107℉
Power
Auto shutdown after 90 seconds idle
Note