2023 Kawasaki Genuine Accessories - Offroad Performance

2023

GENUINE ACCESSORIES & APPAREL

OFFROAD PERFORMANCE

* PROFESSIONAL RIDER ON A CLOSED COURSE

• Kawasaki cautions you that whenever the power output of a motorcycle is increased, reliability and durability may decrease. Therefore, proper and perhaps more frequent maintenance and repair work becomes especially important. The Kawasaki Service Manual contains information that will help enable you to perform essential maintenance and repairs. This manual can be obtained from any authorized Kawasaki dealer or online at Kawasaki.com.

• Installation of race parts requires mechanical knowledge, proper tools and, in some cases, the re-tuning of engine and suspension components. For best results, an experienced tuner should make racing modifications. You may wish to take your vehicle to an authorized Kawasaki dealer to have race parts installed on your motorcycle. There will be a charge for installation.

• Prices, product and specifications are subject to change without notice or liability. Availability is subject to production, stocking and demand. The purchaser accepts all responsibility concerning installation of race parts, including quality, performance, cost or service and/or necessary repairs.

• Kawasaki Accessories or other items in this Performance Parts section are subject to the following conditions:

• These items are intended for closed-course competition only.

• Alteration of emissions-related components can constitute violation of federal and/or state laws. Substantial fines and penalties can result if used for other than closed-course competition use.

• Use of unauthorized components and use of a vehicle in competition can affect a vehicle’s warranty coverage.

• Kawasaki Accessories used in competition are not covered by any warranty and are not returnable.

• Quantities may be limited and replacement parts may not be available.

OFFROAD PERFORMANCE OFFROAD

* PROFESSIONAL RIDER ON A CLOSED COURSE

KX™ FI CALIBRATION KIT (HANDHELD)

Requires Wire Harness (26011-0933) and Bracket (11056-0505) to operate

KX™ FI CALIBRATION KIT

The KX™ FI Calibration Kit features a handheld KX™ FI Calibration Controller which enables riders to adjust engine characteristics, by rewriting actual data maps, to suit their preference • Use without a PC: simply plug the KX™ FI Calibration Controller in the engine’s ECU • Built-in color LCD screen with easy-to-use interface • SD card compatible for data transfer of maps between the controller and a PC • Seven preset settings for easy ECU adjustment to suit track conditions • ECU maps for fuel injection volume and ignition timing based on throttle position and rpm • The KX™ FI Calibration Controller displays the status of a running engine when connected to the ECU • Water-resistant • Includes transfer and diagnostic cables, SD memory card, user manual, and carrying case • Requires Sub Harness (26011-0933) and Bracket (11056-0505) to operate • Fits KX™ 250F (13-18), KX™ 450F (09-10) and (12-18), KX™ 250 (19-23), KX™ 450 (19-23) • Does not fit KX™ 450F (11)

The KX FI Calibration Controller contains seven preset settings that can be quickly and easily used to adjust the ECU to suit track conditions. The provided settings are shown below.

KX™450F (09-10), KX™450F (12-18), Does not fit KX™450F (11), KX™450 (19-23), KX™250F (13-18), KX™250 (19-23)

KX™ FI Calibration Kit

Harness

(19-21)

CD

KX™450F (09-10), KX™450F (12-18), Does not fit

(11), KX™250F (13-18), KX™250 (19-20)

SUB HARNESS

Connects KX™ FI Calibration Kit (Handheld) (999990615) to the main vehicle wiring harness

KX™450 (19+), KX™450F (12-18), KX™450F (09-10), Does not fit KX™450F (11), KX™250 (19+) , KX™250F (13-18),

TUBE CLAMP

Attaches 2019 KX™450 FI Calibration Kit Sub Harness (26011-0933) to the vehicle frameKX™ FI Calibration Kit

KX™450 (19-23)

BRACKET

Attaches KX™ FI Calibration Kit (Handheld) (999990615) to the vehicle frame

KX™450F (12-18), KX™450F (09-10), Does not fit

HANDLEBAR CLAMP

Used on the KX450SR and Monster Energy® Kawasaki race team • The Xtrig PHDS (Progressive Handlebar Dampening System) is a system supported by elastomers designed to absorb engine and chassis vibrations • The system also dampens the forces acting on the handlebar in a horizontal and vertical direction, maintaining steering precision • The handlebar can be adjusted in 12 different positions when the PHDS is mounted • Precision machined and manufactured

KX™450 (22-23)

Handlebar Clamp

FORK CLAMP

99969-3881

Used on the KX450SR and Monster Energy® Kawasaki race team • The XTrig Revolutionary Opposed Clamping System (ROCS) was designed to clamp the upper fork tubes from opposite directions to hold the tubes more evenly and securely • This design reduces inner tube distortion and allows the fork to flex naturally • The triple clamp system’s flexibility is adapted specifically to the forks and chassis which results in improved front wheel traction and positive feedback • Handlebars can be mounted in 12 different positions when using the Progressive Handlebar Dampening System (PHDS) handlebar mounts, sold separately

Features:

• Opposing bolts allow for precise clamping of the fork tubes

• Split clamps improve the bending line of the forks which improves fork response

• CNC manufactured from high-grade aluminum

• Steering head bearing already mounted on steering stem with standard offset

• Lightweight thanks to the removal of material between clamping screws

• Progressive Handlebar Dampening System (PHDS)

KX™450 (22-23)

Fork Clamp

HINSON CLUTCH COVER

99969-3880

The Hinson Clutch Cover is precision machined from billet T-6 aircraft quality aluminum making it stronger than stock. The Hinson Clutch Cover increases oil capacity in the transmission which helps dissipate heat for maximum performance. To help your motorcycle perform optimally the Hinson Clutch Cover directs oil back into the case, keeping the operating temperature cooler.

• Race proven worldwide by Team Honda and Team Suzuki World MX on their World MX Championship RM250 and RMZ450.

• Improves heat dissipation.

• Stronger than stock.

• Oversize covers increase oil capacity in transmission and direct oil back in clutch, both features greatly increasing heat dissipation.

• Precision machined from billet T-6 aircraft quality aluminum to aerospace tolerances.

KX™450 (22-23)

Hinson Clutch Cover

99969-3879

FORK CLAMP

HINSON CLUTCH COVER

PRO CIRCUIT EXHAUST HEAD PIPE

Pro Circuit's Ti-6 Pro Titanium Exhaust System was created for professional racers competing in a series such as AMA Supercross or AMA Motocross to ensure they pass AMA/FIM sound regulations • The Ti-6 Pro Titanium Exhaust System is constructed of titanium throughout the head pipe and mid pipe • The Ti-6 Pro is the next generation of professional level race exhausts • The Ti-6 Pro is a full race system intended for closed-course racing only.

Features Include:

• Passes AMA/FIM sound regulations

• Titanium construction throughout head pipe and mid pipe

• Machined mid pipe to head pipe joint for a better, leak free fit

• Rubber bracket mount

• TIG precision welding

• Made in the USA

KX™450 (22-23)

Pro Circuit Exhaust Head Pipe 99969-3882

PRO CIRCUIT

MUFFLER

Pro Circuit's Ti-6 Pro Titanium Exhaust System was created for professional racers competing in a series such as AMA Supercross or AMA Motocross to ensure they pass AMA/FIM sound regulations • The Ti-6 Pro Titanium Exhaust System is constructed of titanium throughout the canister while the end-cap is carbon fiber • The Ti-6 Pro is the next generation of professional level race exhausts For the 2019-2021 models, a rubber mount has been inserted into the bracket to help prevent potential cracking of the subframe. The Ti-6 Pro is a full race system intended for closed-course racing only.

Features Include:

• Passes AMA/FIM sound regulations

• Titanium construction canister

• Carbon fiber end-cap

• Equipped with RC-4 Resonance Chamber

• Machined aluminum muffler bracket for increased strength and durability

• Asymmetrical muffler configuration for increased packing volume

• TIG precision welding

• Made in the USA

KX™450 (22-23)

Pro Circuit Muffler 99969-3878

PRO CIRCUIT MUFFLER

CIRCUIT EXHAUST

KX™ FI CALIBRATION CD

Contains 2019-2023 KX™ 450 fuel and ignition maps

• The parameters are adjustable to suit specific tracks, surfaces and riding styles

The KX™ FI Calibration Kit allows the user to easily choose from seven preprogrammed fuel and ignition maps • The parameters are adjustable to suit specific tracks, surfaces and riding styles

1. controller sub-harness

2. USB cable

3. software CD-ROM

4. power supply harness

5. ECU mounting bracket (replacement part for use with kit)??

6. controller bracket

7. ECU controller

8. wire harness clamp

9. controller bands

10. upper/lower controller dampers

11. controller damper

KX™450SR (22+)

KX™ FI Calibration CD

KX™450SR (22)

57011-0010

KX™ FI Calibration CD 57011-0002

AIR PUMP

Mini pump with 203mm (8") flex connector and a 0-60 psi gauge for servicing air forks and air shocks

• Pressure can be lowered without removing pump

• One-way check valve prevents pressure loss when pump is removed • For vehicles with air adjustable suspension

KX™450F (13-18)

Air Pump

K56019-060A

OPTIMATE TM-471 LITHIUM BATTERY CHARGER .8A

The OptiMate TM-471 Maintenance Charger by TecMate • The OptiMate TM-471 is a 0.8 amp charger

• It charges and/or maintains most 12V lithium batteries • Unique LiFePO4 battery protection

8-Step Program

1. Low Volt Start (0.5V)

2. Ultra LOW VOLT SAVE

3. LOW VOLT SAVE cell monitoring

4. TEST cell damage

5. Cell-balancing CHARGE

6. OPTIMIZE

7. TEST after CHARGE

8. OptiMate Maintenance

KX™450 (19+) Optimate TM-471 Lithium Battery Charger .8A C57001471

RK EXW GREEN RACING CHAIN

RK's top of the line XW ring chain with an exclusive green finish that is only available directly from Kawasaki

• Chromoly steel construction with solid rollers and bushings

• Clip-type link

KX™450F (06-18), KX™250F (04-18), KX™250 (19-21), KX™450 (19-21)

NM520EXW-120 Green Chain

OPTIMATE TM-471 LITHIUM BATTERY CHARGER .8A

K11001-221

RK

KX FI CALIBRATION CD MANUAL AND DATA AIR PUMP

EXW GREEN RACING CHAIN

REPLACEMENT PLASTICS

Kawasaki Factory OEM plastics used by our Factory Motocross, Supercross and Team GreenTM riders

KX™450 (21-23) / KX™450X (21-23)

Number Plate, Green 58029-0014-290

Fender-Front, Green 35038-0008-290

Fender-Rear, Green 35023-0445-290

Side Panel, Left, Green 36001-0660-290

Side Panel, Right, Green 36001-0662-290

KX™450 (23)

Radiator Shroud, Left, with Decals 49135-5414-290

Radiator Shroud, Right, with Decals 49135-5415-290

KX™450 (22)

Radiator Shroud, Left, with Decals 49135-5283-290

Radiator Shroud, Right, with Decals 49135-5284-290

KX™450 (21)

Radiator Shroud, Left, with Decals 49135-5152-290

Radiator Shroud, Right, with Decals 49135-5153-290

KX™450 (19-20)

Number Plate, Green 58029-0013-290

Fender-Front, Green 35038-0008-290

Fender-Rear, Green 35023-0445-290

Side Panel, Left, Green 36001-0660-266

Side Panel, Right, Green 36001-0662-266

Side Panel, Left, Green 36001-0660-290

Side Panel, Right, Green 36001-0662-290

KX™450 (20)

Radiator Shroud, Left, with Decals 49135-5132-290

Radiator Shroud, Right, with Decals 49135-5133-290

KX™450 (19)

Radiator Shroud, Left, with Decals 49132-5460-290

Radiator Shroud, Right, with Decals 49132-5461-290

KX™450X (23)

Radiator Shroud, Left, with Decals 49135-5437-290

Radiator Shroud, Right, with Decals 49135-5438-290

KX™450X (22)

Radiator Shroud, Left, with Decals ..... 49135-5285-290

Radiator Shroud, Right, with Decals 49135-5286-290

KX™450X (21)

Radiator Shroud, Left, with Decals 49135-5190-290

Radiator Shroud, Right, with Decals 49135-5191-290

KX™450 (19-23) / KX™450X (21-23)

Radiator Shroud, Left, without Decals 49089-0946-290

Radiator Shroud, Right, without Decals 49089-0947-290

SIDE PANEL (GREEN)

FRONT / REAR FENDER (GREEN)

RADIATOR SHROUD, RIGHT

RADIATOR SHROUD, LEFT

REPLACEMENT PLASTICS

Kawasaki Factory OEM plastics used by our Factory Motocross, Supercross and Team Green™ riders

KX™250 (21-23) / KX™250X (21-23)

Number Plate, Green

58029-0014-290

Fender-Front, Green 35038-0008-290

Fender-Rear, Green 35023-0445-290

Side Panel, Left, Green

Side Panel, Right, Green

KX™250 (23)

36001-0660-290

36001-0662-290

Radiator Shroud, Right, with Decals 49135-5350-290

Radiator Shroud, Left, with Decals 49135-5351-290

KX™250 (22)

Radiator Shroud, Right, with Decals 49135-5268-290

Radiator Shroud, Left, with Decals 49135-5269-290

KX™250 (21)

Radiator Shroud, Right, with Decals 49135-5151-290

Radiator Shroud, Left, with Decals 49135-5150-290

KX™250X (23)

Radiator Shroud, Left, with Decals 49135-5453-290

Radiator Shroud, Right, with Decals 49135-5454-290

KX™250X (22)

Radiator Shroud, Left, with Decals 49135-5270-290

Radiator Shroud, Right, with Decals 49135-5271-290

KX™250X (21)

Radiator Shroud, Right, with Decals 49135-5189-290

Radiator Shroud, Left with Decals 49135-5188-290

KX™250 (21-23) / KX™250X (21-23)

Radiator Shroud, Left, without Decals 49089-0946-290

Radiator Shroud, Right, without Decals 49089-0947-290

KX™250 (20)

Number Plate, Green

Fender-Front, Green

Fender-Rear, Green

Side Panel, Left, Green

Side Panel, Right, Green

Radiator Shroud, Left, with Decals

Radiator Shroud, Right, with Decals

58029-0013-290

35038-0008-290

35023-0415-290

36001-0629-290

36001-0631-290

49135-5052-25M

49135-5053-25M

Radiator Shroud, Left, without Decals 49089-0936-25M

Radiator Shroud, Right, without Decals 49089-0986-25M

KX™250 (18-19)

Number Plate, White

Fender-Front, Green

Fender-Rear, Green

Side Panel, Left, White

Side Panel, Right, White

Radiator Shroud, Left, with Decals

Radiator Shroud, Right, with Decals

Radiator Shroud, Left, without Decals

Radiator Shroud, Right, without Decals

58029-0013-266

35038-0008-290

35023-0415-290

36001-0629-266

36001-0638-266

49132-5444-25M

49132-5445-25M

49089-0936-25M

49089-0937-25M

SIDE PANEL (GREEN)

FRONT / REAR FENDER (GREEN)

RADIATOR SHROUD, RIGHT

RADIATOR SHROUD, LEFT

NUMBER PLATE (GREEN)

POLYCARBONATE SKID PLATE KIT

POLYCARBONATE SKID PLATE

4 Flanged Bolts,6X9 (92154-0546) required for fitting onto the KX450 motorcycle • Kawasaki Factory OEM plastics used by our Factory Motocross, Supercross and Team GreenTM riders

KX™450 (19-23)

Polycarbonate Skid Plate 55020-1893

Flanged Bolt 92154-0546

POLYCARBONATE SKID PLATE KIT

Kit contains skid plate and 4 Flanged Bolts for fitting onto the KX™ 450 or KX™ 250 motorcycle • Kawasaki Factory OEM plastics used by our Factory Motocross, Supercross and Team Green™ riders

KX™450 (19-23) / KX™250 (21-23)

Polycarbonate Skid Plate Kit 99994-1532

REAR CARRIER

Durable tubular steel black finish construction mounts securely to the rear chassis • Provides 6.5 pound (3.0 Kg) cargo capacity • Rack dimensions approximately 8" x 10" • Includes integrated tool bag • Does not fit KLX™ 300 off road version

KLX®300 (21-23)

Rear Carrier 99994-1483

HAND GUARD SET

Hand Guard Shell Set is constructed of rugged plastic • All hardware and instructions included KLX®300 (22-23)

Hand Guard Set, Black 99994-1272-68L

KLX®300 (20-21)

Hand Guard Set, Black 99994-1272-6C

KLX®300 SM (21)

Hand Guard Set, Black ________________99994-1248-6C

KLX®300 SM (22)

Hand Guard Set, Black 99994-1248-68L

HANDLE BAR PAD

Thick foam cover for stock handlebar cross bar

• Features the KLX® logo

KLX®300 (20-23)

Handle Bar Pad 99994-1274

TAPERED HANDLE BAR

Rugged tapered steel design has robust 1 1/8" (28.5 mm) clamping diameter with matching aluminum riser bar clamps • Replaces stock handlebar and clamps

KLX®300 (20-23)

Tapered Handle Bar, Silver 99994-1471-458

HAND GUARD SET

Hand Guard Shell Set is constructed of rugged plastic • All hardware and instructions included

KLX®230/KLX®230R (20-23)

Hand Guard Set, Black 99994-1248-6C

KLX®230/KLX®230R (20-23)

Hand Guard Set, Black 99994-1248-68L

HANDLE BAR PAD

Thick foam cover for stock handlebar cross bar

• Features the KLX® logo

KLX®230/KLX®230R (20-23)

Handle Bar Pad

FAT TYPE HANDLE BAR

99994-1274

Rugged tapered steel design has robust 1 1/8" (28.5 mm) clamping diameter with matching aluminum riser bar clamps • Replaces stock handlebar and clamps

KLX®230 SM (23)

Fat Type Handle Bar

HELMET LOCK

99994-1508-18R

Lock your helmet conveniently when you’re off the road • Chassis mounted lock utilizes the Kawasaki One Key System, allowing you to use your ignition key • Steel construction • All required brackets and hardware included • Dealer installation required

• Does not fit KLX® 230 off road version

KLX®230 (20-23)

Helmet Lock

RIM SET

99994-1279

Black or gold finish front and rear wheel rims replace stock silver finish rims • Dealer installation recommended

KLX®230/KLX®230R (20-23)

Rim, Black

KLX®230 SM (23)

Rim, 17" Gold

99994-1251-WC

99994-1850-WC

FAT TYPE HANDLE BAR

HELMET LOCK

RIM SET

REAR CARRIER

Durable tubular steel black finish construction with bright aluminum center plate mounts to the rear chassis • Provides 6.5 pound (3.0 Kg) cargo capacity

• Rack dimensions approximately 10" x 10"

• Includes four welded bungee hooks • Does not fit KLX® 230 off road version

KLX®230 (20-23)

Rear Carrier 99994-1280

SKID PLATE

Durable black ABS plastic construction • Provides full coverage protection of the chassis bottom rails

• Includes oil drain hole to allow oil to be changed without removing skid plate

KLX®230/KLX®230R (20-23)

Skid Plate 99994-1246

FRAME COVER

Durable black ABS plastic construction • Helps provide scuff protection for the chassis side rails

• All hardware and instructions included

KLX®230/KLX®230R (20-23)

Frame Cover 99994-1466

SKID PLATE

FRAME COVER