Contents 1 Introduction 1 1.1 System Overview (시스템 개요) 1 1.2 Aircraft Overview (기체 개요) 2 1.3 Controller Overview (조종기 개요) 3 1.4 Operating Parameters (운영 파라미터) 4 1.5 Autopilot (오토파일럿) 5 1.6 Propulsion (추진력) 5 1.7 LED Meanings (LED의 의미) 5 2 Setup 6 2.1 In the Box (박스 구성품) 6 2.2 Battery (배터리) 6 2.3 Controller (조종기) 8 2.4 Propellers (프로펠러) 9 2.5 Camera (카메라) 9 2.6 Mobile App (모바일 앱) 11 3 Safety 15 3.1 Location (장소) 15 3.2 Environmental Awareness (환경적 인지) 15 3.3 Visual Line of Sight (시야와 시선) 15 3.4 Flight School (항공 학교) 15 3.5 Propellers (프로펠러) 16 3.6 GPS 16 3.7 Home Position (홈 위치) 16 3.8 Altitude Limit (고도제한) 16 3.9 Emergency Procedures (긴급상황 절차) 17 3.10 Flight Battery (비행용 배터리) 18 3.11 Controller (조종기) 18 3.12 Antenna Configuration (안테나 설정) 18 4 First Flight 19 4.1 Preflight Checklist (비행 준비 체크리스트) 19 4.2 Takeoff (착륙) 19 4.3 Landing (이륙) 20 4.4 Return to Home (홈으로 돌아오기) 21 4.5 In-Flight Data (비행 데이터) 22 4.6 Joystick Control (조이스틱 조종) 23 4.7 App Interface Overview (앱 인터페이스 개요) 26 5 Smart Shots 27 5.1 Selfie (셀피) 27 5.2 Cable Cam (케이블 캠) 28 5.3 Orbit (궤도 비행) 30 5.4 Follow (팔로우) 31 6 Alerts 33 6.1 Preflight Errors (비행 전 에러) 33 6.2 In-Flight Errors (운항 중 에러) 34 7 Advanced Settings 37 7.1 Advanced Flight Modes (상급자 모드) 37 7.2 Enabling Advanced Flight Modes (상급자 모드 활성화) 38 7.3 Accessing Advanced Flight Modes (상급자 모드 접근) 38 7.4 Home Position Safety (홈 위치 안전) 38 7.5 Performance Adjustment (기체성능 조정) 39 7.6 Units (단위) 39 7.7 Maximum Altitude Adjustment (고도 제안 조정) 39
8 Support (지원) 40 9 Maintenance (유지 및 보수) 40 9.1 Controller Battery Replacement (조종기 배터리 교체) 40 9.2 Calibrations (캘리브레이션) 41 9.3 Pairing the Controller (조종기 페어링) 42 9.4 Legs (다리) 43 9.5 Battery Tray (배터리 트레이) 46 9.6 Motors (모터) 47 9.7 Factory Reset (공장 초기화) 49 10 Appendix 51 10.1 Specifications (제품사양) 51 10.2 Warranty (보증) 52 10.3 Regulatory Compliance 52
Figures Figure 1.1.3.1:
Solo System Context Diagram 1 Figure 1.2.4.1: Solo Overview 2 Figure 1.3.10.1: Controller Overview 4 Figure 1.4.10.1: Solo Operating Parameters 4 Figure 1.6.10.1: Solo Motor Order 5 Figure 2.1.10.1: Solo Parts 6 Figure 2.2.1.1: Solo Battery Charging 7 Figure 2.2.2.1: Powering Solo 7 Figure 2.3.1.1: Controller Charging 8 Figure 2.3.2.1: Power On Controller 8 Figure 2.4.1.1: Attach Propellers 9 Figure 2.5.1.1: Attach Camera 10 Figure 2.5.2.1: Camera Configuration Process 10 Figure 2.6.2.1: Connect to Solo Link 11 Figure 2.6.3.1: App - Settings Menu 11 Figure 2.6.3.2: App - Wi-Fi Settings 12 Figure 2.6.4.1: Controller Preflight Prompt 12 Figure 2.6.4.2: App - Software Update 12 Figure 2.6.4.3: App - Connecting Instructions 12 Figure 2.6.4.4: App - Instructions List 13 Figure 2.6.4.5: App - Download Update 13 Figure 2.6.4.6: App - Start Update 13 Figure 2.6.4.7: Controller - Updating 13 Figure 2.6.4.8: App - Update Disconnection Conf. 13 Figure 2.6.4.9: Controller Update Complete 14 Figure 2.6.4.10: Controller - Waiting for Solo 14 Figure 2.6.4.11: App - Update Success 14 Figure 2.6.5.1: App - Viewing Video 14 Figure 3.4.5.1: App Flight School 15 Figure 3.9.5.1: Controller - Motor Shutoff 17 Figure 3.12.5.1: Controller Antenna Orientation 18 Figure 4.2.1.1: Controller - Start Motors Prompt 19 Figure 4.2.2.1: Controller - Takeoff Prompts 20 Figure 4.3.2.1: Controller - User-Initiated Landing 20 Figure 4.4.2.1: Return to Home Button 21 Figure 4.4.2.2: RTH Below 21 Figure 4.4.2.3: RTH Above 21 Figure 4.5.2.1: Controller - In-Flight Data 22 Figure 4.6.2.1: Controller Left Joystick 23 Figure 4.6.2.2: Throttle Joystick Behaviors 23 Figure 4.6.2.3: Yaw Joystick Behavior 24 Figure 4.6.2.4: Controller Right Joystick Controls 24 Figure 4.6.2.5: Pitch Joystick Controls 25 Figure 4.6.2.6: Roll Joystick Controls 25 Figure 4.7.2.1: App - Main Interface 26 Figure 4.7.2.1: App - Shot List 26 Figure 5.1.2.1: Selfie Path and Settings 27 Figure 5.1.1.1: App - Selfie Activation 27 Figure 5.1.2.1: App - Selfie Control 28 Figure 5.1.2.2: Controller - Selfie Control 28 Figure 5.1.3.1: App - Selfie Settings 28 Figure 5.2.1.1: App - Cable Cam Setup 29 Figure 5.2.2.1: App - Cable Cam Controls 29 Figure 5.2.2.2: Controller - Cable Cam Controls 29
Figure 5.2.3.1: App - Cable Cam Settings Figure 5.3.1.1: App - Orbit Setup Figure 5.3.2.1: App - Orbit Controls Figure 5.3.2.2: Orbit Controls Figure 5.3.3.1: App - Orbit Settings Figure 5.4.1.1: App - Follow Setup Figure 5.4.2.1: Follow Controls Figure 5.4.3.1: App - Follow Settings Figure 6.1.1.1: Controller - Calibration Progress Alerts Figure 6.1.1.2: Controller - Uneven Surface Alert Figure 6.1.1.3: Controller - Re-Calibration Alerts Figure 6.1.1.4: Controller - Calibration Error Alert Figure 6.1.2.1: Controller - Service Alerts Figure 6.2.1.1: Controller - Altitude Limit Alert Figure 6.2.2.1: Controller - App Connection Alerts Figure 6.2.3.1: Controller - Cont. Disconnected Alert Figure 6.2.3.2: Controller - Controller Signal Alerts Figure 6.2.4.1: Controller - GPS Signal Alerts Figure 6.2.5.1: Controller - Low Battery Alerts Figure 6.2.5.2: Controller - Critical Battery Alert Figure 6.2.6.1: Controller - Controller Battery Alerts Figure 7.2.5.1: App - Advanced Settings Figure 7.3.5.1: App - A and B Presets Figure 7.5.5.1: App - Performance Sliders Figure 7.6.5.1: App - Change Units Figure 7.7.5.1: App - Altitude Limit Figure 8.7.5.1: App - Submit Trouble Ticket Figure 9.1.5.1: Controller Battery Installation Figure 9.2.1.1: App - Compass Calibration Setup Figure 9.2.1.2: App - Compass Calibration Procedure Figure 9.2.2.1: App - Level Calibration Figure 9.3.2.1: Pair Button Figure 9.3.2.2: Detected Solo Figure 9.3.2.3: Solo Paired Figure 9.4.2.1: Leg Types Figure 9.4.1.1: Standard Leg Replacement Process Figure 9.4.2.1: Detaching the Antenna from the Leg Figure 9.4.2.2: Attaching New Leg with Exist. Antenna Figure 9.4.2.3: Attaching Existing Antenna to New Leg Figure 9.4.3.1: Compass Connector on Mainboard Figure 9.4.3.2: Insert New Leg with Compass Figure 9.5.1.1: GPS Cover Removal Figure 9.5.2.1: Battery Tray Removal Figure 9.5.2.2: Battery Tray Detachment Figure 9.6.2.1: LED Cover Removal Figure 9.6.2.2: Motor Pod Removal Figure 9.6.2.3: Motor Pod Disconnection Figure 9.6.2.4: Motor Pod Connection Figure 9.6.2.5: Motor Pod and LED Cover Attachment Figure 9.7.2.1: Pair Button Figure 9.7.2.2: Strobing Pairing Light Figure 9.7.2.3: Controller Reset Figure 9.7.2.4: Controller Update
29 30 30 31 31 31 32 32 33 33 33 34 34 34 35 35 35 36 36 36 36 38 38 39 39 39 40 40 41 41 41 42 42 42 43 43 44 44 44 45 45 46 46 46 47 47 48 48 48 49 49 49 50
Video output Telemetry output Control input
Ground
Air
3DR Solo Controller Operator 3DR Solo App
3DR Link Secure WiFi Network
3DR Solo
1
은색 프로펠러 전원버트 배터리 후면 방향 LED 검정 프로펠러 모터 암 번호
높이:
259mm
Motor-to-motor:
459mm
Weight (카메라 미포함): 1.5 Kg
전면 방향 LED 카메라 고정 마운트 HDMI 케이블
2
3
Antennas
Mobile-device holder
Gimbal controls Joysticks
Screen
Pause Return home Fly Power Options
Estimated flight time
up to 25 minutes*
Default maximum altitude
150 ft. (46 m) above ground level**
Range
.5 miles*** (.8 km)
Payload capacity
1 lb. (450 g)
Cruise speed
18 mph (8 m/s)
Maximum speed
33 mph (15 m/s)****
Wind speed limitation
25 mph (11 m/s)
Operating temperature
32째 F - 113째 F (0째 C to 45째 C)
4
03
01
02
04
5
Solo
Three silver-top props & three black-top props
Controller
Controller charger
Solo charger
6
Charge indicator
Charge indicator
기체가 켜지는 동안 기체를 그대로 두시고 센서가 작동할 수 있게 기다려 주 세요. 이 과정 중, 기체를 움직일 시 캘리브레이션이 부정확해질 수 있으므로 비행 시작 에러 또는 비행 활동 오류가 날 수 있습니다.
2 Hold to power 1 Slide to connect
7
8
모터 라벨 제거
모터 라벨 제거
9
GoPro® The Frame™
Mount your GoPro® upside down.
Your GoPro® HERO 3, 3+ or 4
SETUP
ORIENTATION
ORIENTATION
OFF
OFF
:UP
:AUTO
:VIDEO :OFF
:VIDEO :OFF
Connect the HDMI cable.
EXIT
RESETCAM EXIT
Set the GoPro® HERO3 to inverted orientation: GoPro® Settings
Enable GoPro® HERO4 auto-orientation:
SETUP
Camera Orientation ORIENTATION
ORIENTATION
OFF
OFF
:UP
:AUTO
:VIDEO :OFF
:VIDEO :OFF
EXIT
RESETCAM EXIT
Set the GoPro® to medium field of view:
GoPro® Settings
고프로의 Wi-Fi 가 꺼져 있는지 반드시 확인해주세요. 솔로의 신호를 방해하여 예상치 못한 상황이 발생할 수 있습니다.
10
LTE
7:34 PM
Settings
Airplane Mode WI-FI Bluetooth
Solo_Link-#### On
Cellular
Notifications Control Center Do Not Disturb
General Sounds Wallpapers & Brightness Privacy
11
ARTOO UPDATE SCREEN FEEDBACK V10C Update Requirement Screen
preflight update Required before first flight! Use 3DR Solo App to update
Controller update in progress screen Is displayed after user initiates update in app. Persists until controller update is successful.
Controller updating
Update Timeout If update does not “update-unsucces
Update will take about 5 minutes Please ensure charger is connected Controller may go dark while updating
Update failure If update fails, disp screen Update complete feedback. Tells the user that controller update was successful. HAPTIC: Three 20 millisecond pulses, to communicate update completion. A-Press required to dimiss (same as current implementation)
Controller updated Please reconnect to Sololink wifi Press
to continue
Waiting for Solo Persists until Solo reconnects or Artoo auto-shutdown
waiting for Solo Press
when LEDs are green Update complete (Connects to matching version Solo)
12
Hold
Update unsuccessful (
FLY
FLY
to start motors
update Cable Cam
Orbit
Returns user to hold-Fly-button screen Green Solo LEDs (showing update complete) change to standard red and white when this screen is displayed
Please us the
Prompt stays on screen Post Unlock Behavior
12 After system is unlocke
versions that were last s (Even if they have failed
ARTOO UPDATE SCREEN FEEDBACK V10C Update Requirement Screen
preflight update Required before first flight! Use 3DR Solo App to update
Controller update in progress screen Is displayed after user initiates update in app. Persists until controller update is successful.
Controller updating
Update Timeout If update does not comple “update-unsuccessful” scr
Update will take about 5 minutes Please ensure charger is connected Controller may go dark while updating
Update failure If update fails, display “upd screen Update complete feedback. Tells the user that controller update was successful. HAPTIC: Three 20 millisecond pulses, to communicate update completion. A-Press required to dimiss (same as current implementation)
Controller updated Please reconnect to Sololink wifi Press
to continue
Waiting for Solo Persists until Solo reconnects or Artoo auto-shutdown
waiting for Solo Press
13
when LEDs are green Update complete (Connects to matching version Solo)
12
Upd If up Upd
Update unsuccessful (Artoo a
Required before first flight! Use 3DR Solo App to update
preflight update
Controller update in progress screen Is displayed after user initiates update in app. Persists until controller update is successful.
Required before first flight! Use 3DR Solo App to update
Controller updating
Controller update in progress screen Is displayed after user initiates update in app. Persists until controller update is successful.
Update will take about 5 minutes Please ensure charger is connected Controller may go dark while updating
Controller updating
Update complete feedback. Tells the user that controller update was successful.
Update will take about 5 minutes Please ensure charger is connected Controller may go dark while updating
Update Timeout If update does not complete “update-unsuccessful” screen
HAPTIC: Three 20 millisecond pulses, to communicate update completion.
Update failure A-Press required to dimiss (same as current implementation) If update fails, display “update screen
Controller updated
Update complete feedback. Tells the user that controller update was successful.
Please reconnect to Sololink wifi Press
HAPTIC: Three 20 millisecond pulses, to communicate update completion.
to continue
A-Press required to dimiss (same as current implementation)
Controller updated
Waiting for Solo Persists until Solo reconnects
Please reconnect to Sololink wifi
or
Press
to continue
Artoo auto-shutdown
waiting for Solo
Waiting for Solo Persists until Solo reconnects or
Press
Artoo auto-shutdown
when LEDs are green
waiting for Solo
Update complete (Connects to matching version Solo)
12 Press
FLY
Update If upda Update
when LEDs are green Update complete (Connects to matching version Solo)
12
Hold
FLY
to Update start unsuccessful motors (Artoo and
FLY Cable Cam
Hold
FLY
Orbit
to start motors Returns user to hold-Fly-button screen
update uns
Green Solo LEDs (showing update complete) change to standard red and white when this screen is displayed
Cable Cam
Orbit
Please use 3DR S the update
Returns user to hold-Fly-button screen
Prompt stays on screen until upda
Green Solo LEDs (showing update complete) change to standard red and white when this screen is displayed
Post Unlock Behavior After system is unlocked, user shou versions that were last successfully (Even if they have failed in their mo
14
중요한 안전 수직은 첫 비행 전에 꼭 읽고 이해 하시기 바랍니다. 이 지침은 사고의 위험과 심각한 부상을 예방합니다.
장애물은 기체와 조종기간의 신호를 방해하며, 기체가 Return Home 기능 시 잘못 된 경로로 움직이는 이유가 됩니다.
15
400 ft
400 ft
회전하는 프로펠러는 심각한 부상을 입을 수 있습니다. 절대 움직이는 프로펠러는 만지지 마세요. 기체가 켜져 있을 때, 프로펠러의 회전 반경에는 어떤 물체도 놓지 마세요.
16
KILL SWITCH UI - EMERGENCY MOTOR SHUTOFF
12
Kill Switch Feedback If users holds AB + Pause in flight notification is displayed
FLY
User holds AB + Pause to shut off motors
Hold + to shut off motors
KILL SWITCH UI - EMERGENCY MOTOR SHUTOFF Spot lock
12
Kill Switch Feedback
12 If users holds AB + Pause in flight
FLY
FLY
Progress bar completes After 3000 millisecond hold
notification is displayed
User holds AB + Pause to shut off motors
Hold + to shut off motors
Spot lock
Hold + to shut off motors
Spot lock
Progress bar completes
12
Shutoff Banner Banner shows shutoff taking place
12 After 3000 millisecond hold
FLY
LAND
FLIGHT BATTERY
Hold + to shut off motors
Spot lock
30
%
HOME
5 0
FT
ALTITUDE
PERSISTENT: banner persists until user: -rearms with Fly button -restarts vehicle
FT
Cable Cam Orbit MOTOR SHUTOFF ACTIVATED
17 12 FLIGHT BATTERY
Shutoff Banner Banner shows shutoff taking place
LAND HOME
PERSISTENT: banner persists until user:
20째
18
빌딩이나 나무는 GPS 신호를 감소 시킵니다. GPS 신호의 감소는 예상치 못한 상황을 야기 시킵니다.
MOTOR START & TAKEOFF V4
12
Hold
FLY
to start motors
Cable Cam
12
Hold
Motors off Landing screen after startup, before motors are turned on.
FLY
Orbit
FLY
FLY
to start motors
Fly button safety sequence Progress bar feedback while user holds down “Fly” button.
19
400 ft
400 ft
회전하는 프로펠러는 심각한 부상의 원인이 됩니다. 항상 기체가 어떤 TAKEOFF PART 2 장애물이나 사람 또는 동물로부터 멀리 떨어져 있음을 확인하세요. 12
Auto-takeoff Green bar returns to zero progress position on transition.
FLY
User holds “Fly” to initiate auto-takeoff.
Hold
Cable Cam
TAKEOFF PART 2
“Fly” button LED blinks on Artoo when motors are on. LED becomes solid white when takeoff begins.
to take off
FLY
Orbit
AUTO-LAND 12
Auto-takeoff User holds “Fly” to initiate auto-takeoff.
12 Auto-takeoff
Green bar returns FLY to zero progress position on transition.
FLY
12
User holds “Fly” to initiate auto-takeoff.
Hold
“Fly” button LED blinks on Artoo when motors FLY to off takeoff Hold are on. LED becomes solidtake white when begins.
to take off
FLY
Cable Cam
Cable Cam
Orbit
12
Hold
Orbit
FLY
12
FLY
to take off
Hold
FLY
to take off
Auto-land prompt If user presses “Fly” in flight, the auto-land prompt appears. User holds “Fly” to initiate auto-land.
to land
Rewind
Auto-takeoff User holds “Fly” to initiate auto-takeoff.
FLY
“Fly” button LED blinks on Artoo when motors are on. LED becomes solid white when takeoff begins.
“Fly” button LED blinks on Artoo when motors are on. LED becomes solid white when takeoff begins.
Hold
FLY
Spot lock
12 Auto-takeoff User holds “Fly” to initiate auto-takeoff.
FLY
“Fly” button LED blinks on Artoo when motors FLY are on. LED becomes solid white when takeoff begins.
Auto-land User holds “Fly” to initiate auto-land. Haptic: press and hold feedback is given.
Haptic: press and hold feedback is given. FLY
to land
Hold
이륙 전에 항상 솔로의 위치를 인지하세요. 공중에서 안전하게 위로 이동하고 멀어지도록 비행할 수 있습니다. 솔로가 당신을 바라보고 이륙한 경우 오른쪽 555656 스틱을 뒤로, Orbit 당신을 뒤돌아 Cable 보고Cam 있는 경우,Orbit 오른쪽 스틱을Spot앞으로 하여 거리를 Cable Cam lock Rewind 확보 하세요. 12
12 Auto-takeoff
Auto-takeoff message During auto-takeoff, target altitude message is
User holds “Fly” toFLY initiate auto-takeoff.
FLY
“Fly” button LED blinks on Artoo when motors FLIGHT BATTERY HOME are on. LED becomes solid white when takeoff begins.
Hold
FLY
100
to take off
Cable Cam
Haptic: press and hold feedback is given. ALTITUDE
%
12 FLIGHT BATTERY
100 Hold
FLY
%
HOME
9999 700
to land ALTITUDE
FT
%
FT
Spot lock
Cable Cam
Rewind
FLIGHT BATTERY
100
9999 700
ALTITUDE
FT
Orbit
Telemetry Auto-land Back on telemetry screenauto-land. after auto-takeoff. User holds “Fly” to initiate
FLY FLY
12
displayed. If user presses “Fly” in flight, the auto-land prompt appears. FLIGHT BATTERY HOME Message times out after 3000 milliseconds. User holds “Fly” to initiate auto-land.
100
9999 700
Messgae stays on screen until copter has landed.
FT
ALTITUDE
FT
Telemetry Back on telemetry screen after auto-takeoff.
LAND
FLIGHT BATTERY
FT
HOME
30
5 0
FT
Auto-landing complete Auto-land complete screen shown when copter has touched down. (In case user is not able to see copter.) Message times out after 5000 milliseconds.
ALTITUDE
%
FT
CableLANDING Cam Orbit COMPLETE
12
Telemetry Back on telemetry screen after auto-landing, prior to auto or user initiated disarming.
FLY
Haptic: press and hold feedback is given.
HOME
Auto-landing message During auto-land, landing status is messaged.
Cable Cam IN PROGRESS Orbit LANDING
FLY
Cable CamTO 5 FT ALTITUDE Orbit GOING
12 12
100
Auto-takeoff message
FLY
LAND
Message times out after 3000 milliseconds. FLIGHT BATTERY HOME
%
FT
12 During auto-takeoff, Auto-land prompt target altitude message is
FLY
12
FT
Cable CamTO 5 FT ALTITUDE Orbit GOING
Orbit
AUTO-LAND
9999 700
12 displayed.
FLIGHT BATTERY
HOME
9999 5 착륙을 진행 중, 기체는 현 위치에 착륙 하게 됩니다. 어디가 %되든, 착륙 되는 % 경로가 700 안전한 지 먼저 확인해 주세요. 0
Hold
FLY
ALTITUDE
FT
555656
Spot lock Cable Cam
12
30
FT
to land
Rewind Orbit
Cable Cam
100
%
FT
Orbit
Auto-landing message During auto-land, landing status is messaged.
LAND
FLIGHT BATTERY
FT
ALTITUDE
HOME
9999 700
Messgae stays on screen until copter has landed.
FT
ALTITUDE
FT
프로펠러가 회전 중일 때 기체에 접근하지 마세요. 자동 착륙이나 리턴 홈 기 Cable Cam 후, Orbit LANDING IN PROGRESS 능 프로펠러가 멈출 때까지 기체에 접근하거나 만지지 말고 기다려 주세 요. 12
Auto-landing complete Auto-land complete screen shown when copter has touched down.
LAND
FLIGHT BATTERY
30
%
HOME
5 0
FT
ALTITUDE
FT
CableLANDING Cam Orbit COMPLETE
(In case user is not able to see copter.) Message times out after 5000 milliseconds.
20
항상 리턴 홈을 활성화하기 전에 홈 포인트에 명확한 경로가 있는지 확인합니다.
21
3 2
1
4 5 6 7 8
22
UP Left Stick
ROTATE LEFT
ROTATE RIGHT
DOWN
Left Stick
이륙과 고도를 높이기 위해, 왼 쪽 스틱을 살며시 중앙에서 위로 올 리세요.
왼쪽 스틱을 중앙에 두면, 현재 고 도를 유지 합니다.
왼쪽 스틱을 중앙에서 뒤로 움직이 면, 기체는 고도를 낮춥니다.
Left Stick
Left Stick
왼쪽 스틱을 기체가 지면 근처에 있을 때, 중앙에서 뒤로 끝가지 밀면, 착륙하게 됩니다.
23
Hover + Land Lower just slightly Hover + Land to hover Lower just slightly to hover
Left Stick
Left Left
Left Yaw Left Yaw
Right
왼쪽 스틱을 왼쪽으로 움직이면, 시 계 방향으로 기체가 돕니다.
Right
Right Yaw 왼쪽 스틱을 오른쪽으로 움직이 Right Yaw 며, 시계 반대 방향으로 기체가 돕니다.
왼쪽 스틱을 가민히 내려 놓으 면, 현 위치를 유지 합니다.
Deactivate Hold until propellers Deactivate stop spinning Hold until propellers stop spinning
FORWARD
LEFT
RIGHT
BACK
24
Activate Activate Hold until propellers Hold spinning. until propellers start Activate start spinning. Hold until propellers Activate start spinning. Hold until propellers start spinning. Take-off + Lift Take-off Lift Raise just+slightly Raise just for take offslightly Take-off + Lift for take off Raise just slightly Take-off + Lift or take off Raise just slightly or take off Hover + Land Hover just + Land Lower slightly Lower just to hover slightly Hover + Land to hover Lower just slightly Hover + Land o hover Lower just slightly o hover
Left Yaw Left Yaw
오른쪽 스틱을 앞으로 하면, 기체는 앞으로 움 직입니다.
Forward Forward 오른쪽 스틱을 뒤로 하면, 기체는 뒤로 움직입니다.
Right Yaw Right Yaw
Back Back Back Back Left Left Left
오른쪽 스틱을 왼쪽으로 밀면, 기체는 왼쪽으로 이동 합니다.
Left Right Right
Left Yaw
Left Yaw
Forward Forward
오른쪽 스틱을 오른쪽으로 밀면, 기체는 오른쪽으로 이동 합니다.
Right Right
Right Yaw
Right Yaw
Deactivate Deactivate Hold until propellers Hold spinning until propellers stop Deactivate stop spinning Hold until propellers Deactivate stop spinning Hold until propellers stop spinning
만약 당신이 처음 드론을 비행 하는 거라면, 기본 스킬을 습득하세요. 3drbotics.com/kb/solo/를 방문하시거나, 솔로 앱에 Flight School 에서 조 종 방법과 예시를 확인 할 수 있습니다.
25
2
3
4
5
6
7
8
1
9
10
11
26
3 2 1
항상 솔로 주변 60미터 반경에 장애물이 없는 지 확인 후, Selfie 를 구동해 주세요. 언제든지 Pause 버튼을 누르면, 기체는 정지 합니다. FLY 버튼을 누르면, 수동 모드로 돌아 오게 됩니다.
27
Move along flight path
28
항상 A 지점과 B 지점 사이에 장애물이 없는지 반드시 확인해주세요.
Camera
Cable
29
지상고도의 변화와 상관없이 궤도촬영 시작점을 기점으로 일정하게 궤도를 순항하며, solo 기체가 촬영을 합니다. 촬영 할 대상의 고도가 변화한다면 solo 기체에 영향을 미칠 수 있으므로, 궤도 촬영 시에는 항상 주의하셔야 합니다. 궤도촬영을 시작하시기 전에는 항상 궤도 경로에 방해요소 또는 문제가 없는지 확인하셔야 합니다.
30
Subject altitude
Altitude
Adjust radius Camera
Orbit
팔로우 기능 사용시에는 항상 이동경로에 방해물이 있으면 안됩니다. 이동경로 중 방해물이 있으면 피해갈 수가 없습니다.
31
Adjust following distance
Altitude Camera
Orbit
32
ARMING ALERTS Altitude calibration System self-calibrates altitude after altitude disparity Alert persists until: System self-calibrates (sys then continues sensor check)
Calibration error
Timeout: after 1 minute (?) (results in “sensor error” screen) ARMING ALERTS
Altitude calibration System self-calibrates altitude after altitude disparity
Please restart Solo
Alert persists until: System self-calibrates (sys then continues sensor check) Timeout: after 1 minute (?) (results in “sensor error” screen) Altitude calibration System self-calibrates altitude after altitude disparity
Calibration error
Alert persists until:
Please restart Solo
System self-calibrates (sys then continues sensor check) Timeout: after 1 minute (?) (results in “sensor error” screen)
ARMING ALERTS
Calibrating Solo Please wait
Calibration error Please restart Solo
Altitude calibration System self-calibrates altitude after altitude disparity
Altitude calibration System self-calibrates altitude after altitude disparity
Alert persists until:
Alert persists until:
System self-calibrates (sys then continues sensor check)
System self-calibrates (sys then continues sensor check)
Timeout: after 1 minute (?) (results in “sensor error” screen) Compass error User is asked to use Solo app to calibrate.
Timeout: after 1 minute (?) (results in “sensor error” screen)
Calibrating Solo
Alert persists until:
Please wait
User completes calibration using the app (system then continues sensor check)
PREARM SENSOR ERRORS
Calibrating compass
User powers off controller, or Solo Controller auto-shutdown
Altitude calibration Please wait System self-calibrates altitude after altitude disparity
Altitude calibration Note: Artoo will not assume the same error is present on System and self-calibrates altitude after altitude disparity restart, will run a fresh check when connected to Solo.
Alert persists until:
Alert persists until:
System self-calibrates (sys then continues sensor check)
System self-calibrates (sys then continues sensor check)
Timeout: after 1 minute (?) (results in “sensor error” screen)
Timeout: after 1 minute (?) (results in “sensor error” screen) Compass error User asked to use Solo app to calibrate.
Altitude calibrating
Calibrating Solo
Please wait
Please wait
Alert persists until:
Calibrating compass
Alert persists until:
Compass error User is asked to use Solo app to calibrate.
Please wait
User completes calibration using the app (system then continues sensor User powers off controller, or Solo Controller auto-shutdown Note: Artoo will not assume the same error is present on restart, and will run a fresh check when connected to Solo.
User completes calibration using the app (sys then continues sensor check)
PREARM SENSOR ERRORS
Throttle too high
Compass error This flight requires User asked to use Solo mode app to calibrate.
low throttle before starting motors
Alert persists until:
Powers off controller, or Solo Controller auto-shutdown Compass Note: Artooerror will not assume the same error is present on User is asked usea Solo to calibrate. restart, and willtorun freshapp check when connected to Solo.
Altitude calibration System self-calibrates altitude after altitude disparity Alert persists until:
Compass error User asked to use Solo app to calibrate. Alert persists until:
User completes calibration using the apppersists (sys thenuntil: continues sensor check) Alert User completes User completes calibration using the app (system then continues sensor check) calibration using the app (sys then continues sensor che Powers off controller, or Solo
Compass error
System self-calibrates (sys then continues sensor check) User powers off controller, or Solo
Throttle too high
Calibrating compass Please calibrate compass using the 3DR Solo app Altitude calibrating Please wait Please
Powers off controller, or Solo
Level error Timeout: after 1 minute (?) (results in “sensor error” screen) Controller auto-shutdown Controller auto-shutdown User is asked to use Solo app to calibrate Note: Artoo will not assume the same error is present on This flight mode Note: Artoo will not assume the same error is present on Note: persists Artoo willuntil: not assume therequires same errorlow is present on Alert restart, and will run a fresh check when connected to Solo. restart, and will run a fresh check when connected to Solo. throttle starting restart, and will runbefore a fresh check whenmotors connected to Solo. User complete calibration using the app (sys then continues sensor check) wait Controller auto-shutdown
Powers off controller, or Solo
PREARM SENSOR ERRORS Controller auto-shutdown
Uneven surface
Level error User is asked to use Solo app to calibrate
Note: Artooerror will not assume the same error is present on Compass Level error restart, and to willuse runSolo a fresh when connected to Solo. User asked appcheck to calibrate. User is asked to use Solo app to calibrate Altitude calibration Compass error System self-calibrates altitude after altitude disparity User asked to use Solo app to calibrate. Alert persists until: User complete calibration using the app (sys then continues sensor check) Alert persists until: Alert persists until: User complete calibration using the app (sys then continues sensor chec Powers off controller, or Solo User completes calibration using the app (sys then continues sensor check) Alert persists until: System self-calibrates (sys then continues sensor check) Powers off controller, or Solo Controller auto-shutdown User completes calibration using Powers the app off (syscontroller, then continues or Solosensor check) Timeout: after 1 minute (?) (results in “sensor error” screen) Catch-All Controller auto-shutdown Note: Artoo will not assume the same error off is present on or Solo Powers controller, Controller auto-shutdown Please calibrate level restart, and will run a fresh check when connected to Solo. Remaining rare but problematic APM errors Note: Artoo will not assume the same error is present on using the 3DR Solo app Controllerlow auto-shutdown This flight mode requires Note: Artoo will not assume the same error is present on will be captured for surface Moveunder Soloa catch-all to a level restart, and will run a fresh check when connected to Solo. restart, will tickets run a fresh check when connected to Solo. throttle motors logging and trouble Please wait Please calibrate compass using before starting Note: Artoo will not assume the same error is present on restart, and will run a fresh check when connected to Solo. the 3DR Solo app
Move Solo to a level surface
Alert persists until:
Level error
Throttle too high Uneven surface Altitude calibrating Compass error Service required
Sensor error screen For sensor errors requiring user-initiated restart
Catch-All Level error Use 3DR Solo app to Level log aerror trouble Compass error User is asked to use Solo app to calibrate User asked to use Solo app to calibrate. ticket with customer Usersupport is asked to use Solo app to calibrate Remaining rare but problematic APM errors will be captured under a catch-all for Alert persists until: logging trouble tickets Alert persists until: User complete calibration using the app (sys then continues sensor check) User complete calibration using the app (sys then continues sensor check) User completes calibration using the app (sys then continues sensor check) Powers off controller, or Solo Powers off controller, or Solo Powers off controller, or Solo Controller auto-shutdown Controller auto-shutdown Controller auto-shutdown Note:error Artoo not assume the same error is present on Note: Artoo will not assume the same is will present on Use 3DR Solo app to logArtoo aconnected trouble level surface Please calibrate compass using and will run fresh check when to Solo.the same error is present on Note: will not assume restart, and will run a fresh checkrestart, when connected to aSolo. restart,support and will run a fresh check when connected to Solo. the 3DR Solo app ticket with customer Alert persists until:
Sensor error
Service required Compass error Level errorUneven surface
Please try and restart Solo
Please calibrate levelMove Solo to a using the 3DR Solo app Control sticl error
Level error Catch-All Sensor error screen User is asked to use Solo app to calibrate sensor errors requiring user-initiated restart Controller starts with stick values inFor range. Remaining rare but problematicAlert APMpersists errors until: will be captured under a catch-all for logging trouble tickets User complete calibration using the app (sys then continues sensor check) Persists until:
Control stick error
Powers off controller, or Solo
Contact 3DR customer support
Sensor error Service required Level error
Please calibrate level Please try and restart Solo Use 3DR Solo app to log a trouble using the 3DR Solo app ticket with customer support
?
Unknown battery Battery % not be accurate
Battery unknown Displayed if Artoo is powered on with a battery has an ID resistor unknown to Artoo. (Not logged in current software version’s index.) Control sticl error HAPTIC: Strong feedback, 40 millisecond pulse Persists until:“waiting for Solo” After Solo is disconnected, Artoo should display Controller starts with stick values in range.
Controller auto-shutdown Note: Artoo will not assume the same error is present on restart, and will run a fresh check when connected to Solo.
Sensor error screen For sensor errors requiring user-initiated restart
33
Calibrating compass Please wait
Alert persists until:
User powers off controller, or Solo
Powers off controller, or Solo
User completes calibration using the app (sysauto-shutdown then continues sensor check) Controller
Level error
Controller auto-shutdown
Powers off controller, or Solo Note: Artoo will not assume the same error is present on calibrate level Please auto-shutdown restart, and will run a fresh check when connected to Solo. using the 3DRController Solo app
Compass error
Please calibrate compass using the 3DR Solo app
ARMING ALERTS
Note: Artoo will not assume the same error is present on restart, and will run a fresh check when connected to Solo.
Note: Artoo will not assume the same error is present on restart, and will run a fresh check when connected to Solo.
Compass error Sensor error screen Altitude calibration User asked to use Solo app to calibrate. For sensor errors requiring user-initiated restart System self-calibrates altitude after altitude disparity Level error Alert persists until: User is asked to use Solo app to calibrate Alert persists until: System self-calibrates (sys then continues sensor check) Alert persists until: User completes calibration using the app (sys then continues sensor check) Powers off controller, or Solo
Throttle too high Calibration error
Timeout: after 1 minute (?) (results in “sensor error” screen)using the app (sys then continues sensor check) User complete calibration
Sensor error
Powers off controller, or Solo
Controller auto-shutdown
Level error
Controller auto-shutdown try and restart Solo This flight mode requires low Please restartNote: present on SoloArtoo will not assume the same error isPlease restart, and will run a fresh check when connected to Solo. throttle before starting motors Note: Artoo will not assume the same error is present on Please calibrate level restart, and will run a fresh check when connected to Solo. using the 3DR Solo app
Control sticl error Altitude calibration Level error System self-calibrates altitude after altitude disparity User is asked to use Solo app to calibrate Persists until: Sensor error screen Alert persists until: For sensor errors requiring user-initiated restart Alert persists until: Controller starts with stick values in range. System self-calibrates (sys then continues sensor check) User complete calibration using the app (sys then continues sensor check)
Powers off controller, or Solo
Calibrating Solo Uneven surface
Timeout: after 1 minute (?) (results in “sensor error” screen)
Control stick error
Controller auto-shutdown
Move Solo to a level surface
Please
Contact 3DR customer support
Sensor error
Note: Artoo will not assume the same error is present on wait restart, and will run a fresh check when connected to Solo.
Please try and restart Solo
IN-FLIGHT ALERTS: CONTROLLER RELATED Battery unknown Displayed if Artoo is powered on with a battery has an ID resistor unknown to Artoo. (Not logged inValue current software version’s index.) Controller out of Range User is asked to contact customer support HAPTIC: Strong feedback, 40 millisecond pulse Remaining rare but problematic APM errors Alert persists until: will be captured under a catch-all for persists until: Alert Persists until: After Solo is disconnected, Artoo should display “waiting for Solo” logging trouble tickets TIMEOUT: 5000 milliseconds starts with values sensor in range. User completes calibration usingController the app (system thenstick continues check)
Compass error User is asked to use Solo app to Control calibrate. sticl error
Catch-All
?
Unknown battery Calibrating compass Battery % not be accurate Control stick error Control stick error Service required Use 3DR Solo app to log a trouble ticket with customer support
Please wait
Contact 3DR
User powers off controller, or Solo
go to persistent hint-box message
Controller auto-shutdown
(persistent until reboot)
Note: Artoo will not assume the same error is present on Solo will customer restart,support and will run a fresh Dismiss check when connected to Solo.
12
Return
FLIGHT BATTERY
48
%
return home
Contro Contact 3DR Su
Compass error RC Failsafe Battery unknown User asked to use Solo app to calibrate. Controller signal lost, RTH screen Displayed if Artoo is powered on with a battery has an ID resistor unknown to Artoo. (Not logged in current software version’s Alertindex.) persists until: Alert persists until: HAPTIC: Strong feedback, 40 millisecond pulse TIMEOUT: 5000 milliseconds User completes calibration using the app (sys then continues sensor check) After Solo is disconnected, Artoo should display “waiting for Solo” Powers off controller, or Solo
?
Throttle too high Unknown battery
Controller auto-shutdown
Controller signal lost
Soloon will return home This flight mode requires low Note: Artoo will not assume the same error is present Battery % not be accurate restart, and will run a fresh check when connected to Solo. throttle before starting motors Dismiss
IN-FLIGHT ALERTS
RC Signal Recovered User can press Fly to recover
Level error User is asked to use Solo app to calibrate
Alert persists until:
Alert persists until: User complete calibration using the app (sys then continues sensor check) Maximum Altitude Powers off controller, or Solo User is told that maximum altitude has been reached
Uneven surface
Controller auto-shutdown
User presses Fly and enters Fly mode HAPTIC: 40millisecond so user is aware that they can take control
Signal recovered
Vehicle is not able to go higher than max altitude
Note: Artoo will not assume the same error is present Alert appears once peronflight and is triggered at 100 FT by default. restart, and will run a fresh check when connected to Solo. Alert persists until:
Move Solo to a level surface
Maximum altitude Preset max altitude reached
TIMEOUT: 5000 milliseconds HAPTIC: Double buzz 40-40 millisecond
RC Failsafe (No GPS) Controller signal lost, emergency land screen
Catch-All
Alert persists until:
Remaining rare but problematic APM errors will be captured under a catch-all for logging trouble tickets Crash Detected User can use app to log a support ticket
TIMEOUT: 5000 milliseconds
Controller signal lost
Alert persists until:
Service required
Emergency landing started
User presses A
Use 3DR Solo app to log a trouble ticket with customer support
HAPTIC: Quad buzz: 40-40-40-40
Crash detected Press
Solo SFX: Start lost call ping if more than 10 m away
to dismiss
GPS signal lost (Switches to FLY: Manual) Alert persists until: TIMEOUT: 3000 milliseconds HAPTIC: Triple buzz twice: 30-30-30, 30-30-30
GPS lost Switching to manual control 12 FLIGHT BATTERY
48
FLY
Camera paddle and dial failure
HOME
324 84
GPS signal recovered FTB) (No advanced mode, Manual mode not set to A or
ALTITUDE Switches to FLY when GPS % is recovered Alert persists until:
TIMEOUT: 3000 milliseconds
FT
Alert triggered on input error on the paddle or tilt speed dial potentiometers TIMEOUT: 5000 milliseconds
34
FLIGHT BATTERY
48
Alert persists until:
HOME IN-FLIGHT BANNER ALERTS
324 84
System self-calibrates (sys then continues sensor check)
FT
Timeout: after 1 minute (?) (results in “sensor error” screen)
ALTITUDE
%
12
FT
FLIGHT BATTERY
48
324 84 FT
3DR Solo app connected Alert persists until:
HOME
FLIGHT BATTERY
324 84
ALTITUDE
12
FLY
FT
FLIGHT BATTERY
48
324 84
System self-calibrates (sys then continues sensor check)
FT
Timeout: after 1 minute (?) (results in “sensor error” screen) Timeout: after 1 minute (?) (results in “sensor error” screen) ALTITUDE Solo app disconnected (Banner) % System self-calibrates altitude after altitude disparity
FT
Alert persists until:
HOME
48
324 84
3DR Solo app disconnected
System self-calibrates (sys then continues sensor check) 3DR Solo app connected
FT
Timeout: after 1 minute (?) (results in “sensor error” screen)
ALTITUDE
%
FT
Solo app disconnected (Banner) System self-calibrates altitude after altitude disparity
12
12
FLY Landing Complete Screen showing automatic landing is complete
FLY
FLIGHT BATTERY
48
%
3DR Solo app disconnected
FLIGHT BATTERY Alert persists until:
HOME
324 84
ALTITUDE
12
FLY
FT
48
Landing complete
48
Timeout: after 1 minute (?) (results in “sensor error” screen)
Landing Complete FTautomatic landing is complete Screen showing Alert persists until:
HOME
324 84
3DR Solo app disconnected
FT
ALTITUDE
Controller Value out of Range User is asked to contact customer support Landing Complete Screen showing automatic landing is complete Alert persists until:
FT
FLY
Controller connection poor (Banner)
Disconnected
%
System self-calibrates (sys then continues sensor check)
FT
ALTITUDE
%
12
48
324 84
TIMEOUT: 3000 milliseconds IN-FLIGHT ALERTS: CONTROLLER RELATED
%
FLIGHT BATTERY
Alert persists until:
HOME
TIMEOUT: 3000 milliseconds
FT
FLIGHT BATTERY
12
Alert persists until:
HOME
System self-calibrates (sys then continues sensor check)
FT
%
Solo app connected (Banner) System self-calibrates altitude after altitude disparity
Solo app 12disconnected (Banner) FLY System self-calibrates altitude after altitude disparity
FLY
48
System self-calibrates (sys then continues sensor check)
FT
Timeout: after 1 minute (?) (results in “sensor error” screen) IN-FLIGHT BANNER ALERTS
ALTITUDE
%
FLIGHT BATTERY
Alert persists until:
HOME
3DR Solo app connected
12
Solo app connected (Banner) System self-calibrates altitude after altitude disparity
FLY
Landing complete
Appears onceBATTERY connection strength is HOME below average performance FLIGHT for X time.
48
324 Control%stick error 84 Disconnected
HOME
324 84
TIMEOUT: After 3000 milliseconds
FT
ALTITUDE
12
FT
ALTITUDE
Alert persists until: TIMEOUT: 5000 milliseconds
TIMEOUT: 3000 milliseconds go to persistent hint-box message
(persistent until reboot)
FLIGHT BATTERY
48
IN-FLIGHT ALERTS: CONTROLLER RELATED Disconnected from Solo
%
Appears once connection strength is below average performance for X time.
HOME
324 84
Landing complete
%
324 84
FT
ALTITUDE
FT
Control stick error Contact 3DR Support after landing
TIMEOUT: After 3000 milliseconds
FT
Controller FT Value out of Range User is asked to contact customer support
12
Disconnected
FLIGHT 5000 BATTERY TIMEOUT: milliseconds
48
48
HOME
324 Controller % signal lost 84 FT
go to persistent hint-box message
ALTITUDE
(persistent until reboot)
RC Failsafe Controller signal lost, RTH screen Return Home Controller connection poor (Banner)
Alert persists until: Appears once connection FLIGHT BATTERY HOME strength is below average performance for X time. TIMEOUT: 5000 milliseconds
Alert persists until:
Disconnected from Solo
Solo will return home
48
HOME
ALTITUDE
12
Control stick error
Return Home
FLIGHT BATTERY
Controller connection poor (Banner) FT
Solo will return home
FT
12
324 84
TIMEOUT: After 3000 milliseconds FT
%
Solo will return home FT
ALTITUDE
FT
Control stick error Contact 3DR Support after landing
Disconnected from Solo
RC Failsafe Controller signal lost, RTH screen
RC Signal Recovered User can press Fly to recover
Alert persists until:
Alert persists until:
TIMEOUT: 5000 milliseconds
User presses Fly and enters Fly mode HAPTIC: 40millisecond so user is aware that they can take control
Controller signal lost
Signal recovered
Solo will return home
RC Signal Recovered User can press Fly to recover
RC Failsafe (No GPS) Controller signal lost, emergency land screen
Alert persists until:
Alert persists until:
User presses Fly and enters Fly mode
TIMEOUT: 5000 milliseconds
HAPTIC: 40millisecond so user is aware that they can take control
Signal recovered
Controller signal lost Emergency landing started
RC Failsafe (No GPS) Controller signal lost, emergency land screen Alert persists until: TIMEOUT: 5000 milliseconds
Controller signal lost Emergency landing started
12 FLIGHT BATTERY
FLY
Camera paddle and dial failure
HOME
324
FT
Alert triggered on input error on the paddle or tilt speed dial potentiometers TIMEOUT: 5000 milliseconds
35
HAPTIC: Quad buzz: 40-40-40-40
Crash detected
GPS lost
Solo SFX: Start lost call ping if more than 10 m away
Switching to manual control Press
to dismiss
Modified Telem screen (Version 1) Now shows new mode. A & B functions that require GPS are greyed out.
GPS signal lost (Switches to FLY: Manual)
6
FLY:Manual
Alert persists until:
FLIGHT BATTERY
HOME
48
324 84
TIMEOUT: 3000 milliseconds
FT
HAPTIC: Triple buzz twice: 30-30-30, 30-30-30
ALTITUDE
%
GPS lost
FT
Switching to manual control Cable Cam
Orbit
GPS signal recovered (No advanced mode, Manual mode not set to A or B) Switches to FLY when GPS is recovered Alert persists until: TIMEOUT: 3000 milliseconds
GPS ready
HAPTIC: 40 millisecond buzz for awareness
Switching to FLY
CONTROLLER BATTERY WARNINGS + PROMPTS Between 5% and 10% user is asked to charge soon Message only appears when Solo is not in flight (pre-flight state, motors not started.)
GPS signal recovered (User who has either advanced mode enabled, or manual set to A or B)
Helps user catch low battery before flight.
(When home is already set) Switches to FLY form Fly:Manual when user presses Fly
charge soon
Alert persists until:
GPS ready
TIMEOUT: 3000 milliseconds
Low controller battery Dismiss
Press
for GPS control
FLY
12
HOME
48
HAPTIC: 20 milliseconds every 3 seconds until press
324 84
FT
%
Alert persists until user sets home
Good controller battery state
Stabilize
FLIGHT BATTERY
GPS signal established (User took off without GPS, no home position, regardless of advanced modes)
Cable Cam
ALTITUDE
FT
Orbit
GPS found Press
FLY
Fullscreen prompt at 5% Message timeout after 3000 miliseconds. Go to previous screen + minimized prompt (continuous until landing.)
to set home CONTROLLER BATTERY WARNINGS + PROMPTS Between 5% and 10% user is asked to charge soon Message only appears when Solo is not in flight (pre-flight state, motors not started.)
land soon
Controller Battery at 5% Helps user catch low battery before flight.
charge soon
12 FLIGHT BATTERY
48
Dismiss
%
12
(Battery level now known in 3% chunks)
HOME
324 84
FT
ALTITUDE
Good controller battery state
Stabilize
FLIGHT BATTERY
Slider message persists Battery updates to red fill for 3%-5%
Stabilize
Low controller battery
FT
HOME
48
324 84
FT
%
ALTITUDE
Controller battery low Cable Cam Orbit Please land soon
FT
Cable Cam
Orbit
CONTROLLER BATTERY WARNINGS + PROMPTS Between 5% and 10% user is asked to charge soon Message only appears when Solo is not in flight (pre-flight state, motors not started.)
(If GPS Lock is present) Fullscreen prompt at 5% Message timeout after 3000 miliseconds. Go to previous In-flight: At 0%, Solo returns to home location screen + minimized prompt (continuous until landing.) Message present until controller shuts down
Helps user catch low battery before flight.
charge soon
land soon
Returning home
Low controller battery
Controller Battery at 5%
Controller battery at 0%
Dismiss 12 12 FLIGHT BATTERY
48
%
Cable Cam
Slider message persists Battery updates to red fill for 3%-5%
Stabilize
Good controller battery state
Stabilize
FLIGHT BATTERY
HOME
324 84
FT
ALTITUDE
FT
Orbit
48
%
(Battery level now known in 3% chunks)
HOME
324 84
FT
ALTITUDE
FT
Controller battery low Cable Cam Orbit Please land soon Fullscreen prompt at 5% Message timeout after 3000 miliseconds. Go to previous
(If GPS Lock is not present) In-flight: At 0%, auto-land
36
Message present until controller shuts down
상급자 비행 모드 전문가 전용 모드입니다. 드론 비행이 숙련되지 않으신 분들은 상급자 비행 모드 사용을 자제하여 주십시오.
아크로 비행 모드는 전문가 또는 드론이 숙련된 상급자만 사용하셔야 합니다. 전문적인 기술이 없으면, 기체의 추락 위험이 높습니다.
37
GPS가 잠겨진 상태로 이륙하였다면, 최초 이륙 지점 복귀 기능을 사용하시면 안됩니다.
38
39
40
41
42
1
Antenna
Compass Antenna Standard
43
2 1
3
2 1
5 mm between antenna and foot 2
1 3
44
45
GPS connector
46
47
2 1
48
공장 초기화를 하시기 전에 반드시 고객센터에 문의하시기 바랍니다. 제품에 심각한 손상을 입을 수 있습니다.
49
50
51
52
53