HAMMER MILL
ILLUSTRATED PARTS BREAKDOWN
Lancaster Parts & Equipment 2008 Horseshoe Rd, Lancaster PA 17602 lancasterpartsandequipment.com Ph: 717 299-3296 Fax: 717 299-2382
1
Table of Content PTO Shaft.....................................................................3 Main frame....................................................................4
1 2 4
Wheels, Hubs, Bearings................................................5
LHM173 = H.M. End1-3/4 Spline
Main pulleys & Belts......................................................6 Main Idler Pulleys..........................................................7 Front Bearing Grease Hoses /Feed Hopper Spinner....8 Front Shields.................................................................9 Main Hammer Mill (Top) + Screen Door.......................10
3
Main Hammer Mill (Bottom)..........................................12 Hammer Drum .............................................................14 Dust Collector & Cyclone..............................................15 Hyd. Hand Pump, Feed Auger Cylinder........................16 Discharge Auger collapse Cylinder...............................17
LHM173 =Tractor End1-3/8 Spline LHM174 =Tractor End1-3/4 Spline
Hydraulics.....................................................................18 Feed Auger Arm............................................................20
Item
Feed Auger Top.............................................................22
2
Feed Auger Bottom.......................................................24
1 3 4
Part# BOM ID LHM410 1 302-5500 2 LHM411 3 921-4400 4
2
4
Description PartNo Description PTO Cover (Small End) (small end) LHM410 PTO Cover Cross Bearing KitBearing Kit 302-5500 Cross PTO Cover (Large End) LHM411 PTO Cover (big end) Shield Bearing 921-4400 Shield Bearing Kit
QTY Qty
11 22 11 22
Discharge Auger Top.....................................................25 Discharge Auger Bottom, Rear Belts & pulleys.............26
2
3
1 4
1
3
2
4
5
2
5
3
6
7
8
9
10
11
7
6
13
14 12
See Next Page
Item Item 1 2 3 4 5 6 7
Part# HP-12180 HMFRA170 Jack DRUHOU233 HM40628 SHI312 HMFRA185
Description Hyd. Hand Pump Hitch Jack (Side Wind) JDS07-28PP Screen Holder Channel Feed Auger Holder Pin W/ Chain Jack Holder Plate
QTY 1 1 1 2 1 1 1
1 2 3 4 5 6 7 8 9 10 11 12 13 14
4
Part# LHM269 Cotter SE16289 LM69349 LM69310 LHM266 LM67010 LM67048 LHM264 LHM263 LHM262 LHM261 LHM259 LSC426
Description Wheel Shaft 3/16 X 2� Cotter Pin Grease Seal Inside Wheel Bearing Inside Bearing Race Wheel Hub Outside Bearing Race Outside Bearing Washer Wheel Castle Nut Hub Cap Rim Tire Axle - Hub Assembly
QTY 2 2 2 2 2 2 2 2 2 2 2 2 2 2
5
16
5
10
4 3
12
12
11
10
13 7
18 19
13
17 9
5 6
1
8
19
8
18
2
14
Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
6
19 20
Part#
5VX680 5VX540 SF-2.4375 PLU5V7.1.8 129768 Key Key SK-2500 PUL5V6.3.3 PUL5V14.3 E-1750 Key FB-2500 HM30146 FB-175HM HM30116 PUL5V16.0.8 Key HM30152 F-2500
3
16 6
17
6
15
9 5
15
7
2
20
14
4
1
12 10
11
Description Gates 5VX 680 Belts Gates 5VX 540 Belts SF 2½” Bushing 5V, 8 grove Pulley 2-7/16 Piloted Flange Grip Tight Bearing 5/8” X 5/8” Key 5/8” X 3/8” Key SK 2½” BUSHING 5V 6.3, 3 Groove Pulley 5V 3 Groove, 14” Pulley E 1¾’’ Bushing 3/8” X 3/8” Key 2½” 4 Holed, piloted Bearing, Setscrew Locking
Bearing Mount Cover Plate 1¾” Piloted Flange Bearing w/ Eccentric Locking Collar Drum Cover Plate 5V 8 Groove,16” Pulley 5/8” X 1/2” Key Hammer Rod Hole Cover F 2½” Bushing
QTY 8 3 1 1 2 1 1 1 1 1 1 1 2 1 2 2 1 1 2 1
Item
Description
4
Part# HM30177 HM30178 HM40643 LHM182
5
COLLAR1.1250
1-1/8 Shaft Collar
6
Bushing HM40647 HM30180 Bolt Spacer Spacer PULID6.5X3.0 Nut PULID5X2.25 Blot Washer HM40636 LSC442 Nut
1-1/8” I.D. x 1.3/8” O.D. x 1.3/16” Long Bronze
1 2 3
7 8 9 10 11 12 13 14 15 16 17 18 19
Shield Mount Idler Bracket Brace Spring
1-1/8” Shaft Idler Support 5/8’’ by 8’’ Flat SOC Bolt 1-1/16” Spacer 1-13/16” Spacer 6½’’ X 3” Idler Pulley 5/8” Lock nut Idler Pulley 5” x 2-1/4” 5/8 Machine bolt A Stack of 5/8” Washers Idler Bracket 6” Adjuster Rod 5/8” Flange nut
QTY 1 1 1 1 3 2 1 1 1 1 2 1 1 1 1 ? 1 1 1
7
16
1
2
3
1
4
5
6
7
8
9
1
10
2 Item
7
Part# FB-11250 HM40188 HM40623 Key LOVJ1.125 LOVJSPI LOVJ1.00
8
FEEAUG453 Hyd. Motor Mount
9
Key
1” X ¼” Woodruff Key
10
HM-01012
CL101-1012 Hyd Motor
1 2 3 4 5 6
Description
QTY
1-1/8” Three Holed Flange Bearing Spinner Bearing Plate ¼” X ¼” Key Love-Joy 1.1/8” Bore 1/4 Key (type L100) Love-Joy Rubber Spider for type L100 Love-Joy 1” Bore 1/4 Key (type L100)
1
2 1 1 1 1 1 1 1 1 1
1 2 3 4 5 6
Part# TGRH1 MGRH2 BGRH3 ZERSTR PP-2GCO Washer
Description Middle Grease Hose Bottom Grease Hose 1/8’’ Straight Grease Zert 1/8” Galv. Coupling
12 13
3/8 Washer
3 4 5
2
6 7 8 9 10 11 12 13
6 4 5
8
14
3
8
14
2
1 1 1 3 3 3
Top Grease Hose
6 7
1
QTY
15
11
Item Item
3
10 9
15 16
Part# HM40206 HM40207 HM40205 HM40204 SHI244 Chain SHI246 SHI245 LSC157 LSC158 LSC159 HM30177 SHI241 HM40643 HM30180 HM40612
Description Top Shield Side Shield Top Door Bottom door PTO Cover Cover Chain PTO Cover U Bracket Shield Pin Hold-Down Strap Hold-Down Strap U Bracket Hold-Down Strap Hook Shield Mount 7/16” Shield Pin Brace Idler Support PTO Holder
5
4
QTY 1 1 1 1 1 1 1 1 3 3 3 1 4 1 1 1
9
5 15
3 Standard with each mill comes 2, 1/4” Screens, 2, 5/16” Screens & 2, 3/8” Screens. Part # are as Follows: 1/4” Screens = HM40186-.25 5/16” Screens = HM40186-.3125 3/8” Screens = HM40186-.375 Also available are: 1/8” Screens = HM40186-.125 3/16” Screens = HM40186-.187 1/2” Screens = HM40186-.50 5/8” Screens = HM40186-.625
4 4
9
6 1 7 14
11
13 2
10
Item
8
14
Part# HM30110 HM30111 HM40113 HM40MAG HM40112 HM40114 HM40145 HM40639 HM40638 Screens HM40130 DRUHOU284 HM40153 HM30132
15
HM40648
16
HM40134 HM30136 HM30165-R HM30165-L
1 2 3 4 5 6 7 8 9 10 11
12
12 13
16 17 19
17
18
18 19
Description Main Back Plate Main Front Plate Top Left Hopper Plate Magnet (changed 2014 & newer) Top Right Hopper Plate Right Drum Side Left Drum Side Spinner Hole Cover Plate (for removing the spinner) Back Spinner Hole Cover Plate See Table up top Screen Holder Bracket Screen Door Adj. Rod Bottom Screen Bar Inside Screen Stops Corn Deflector ( this part is optional, not included with all models) Drum Door Screen Door Side Filler Strips R.H. Side Door Latch L.H. Side Door Latch
QTY 1 1 1 2 1 1 1 1 1 2 2 4 1 4 1 2 4 2 2
17
10
11
1 1 Item
7
3
6
4
Description
7
Part# HM40127 HM40133 HM40147 HM40153 DRUHOU141A FB-2500 HM40635
8
BMA111
Clean-out Cover
9
BOTAUG165
Test Tube
10
SA1227
Bottom Discharge Auger
11
HM40137
Bottom Discharge Tube
12
¾” Piloted Flange Bearing w/ Eccentric Locking Collar
13
FB-175HM HM30146
14
SPR2.5EX
Spring
15
BOTAUG462
L Bolt for Test Tube
16
BOTAUG412
Test Tube Plate
1 2 3 4 5
5
6
8 6
2
14 10
16
15
9
Side Plates Bottom Plate w/ cleanout hole Bottom Plate w/out cleanout hole Bottom Screen Bar Line Shaft 2 1/2” 4 Holed, piloted, Round, Setscrew Line Shaft Cover
Bearing Mount Cover Plate
QTY 2 1 1 1 1 2 1 1 1 1 1 1 1 2 2 1
11 12
12
13
13
3 1 4
7
5
9
6
4
6
2 12 13
11
14
9
6
15 3
2
8 7
1
4
5
10
10
8 Item 1 2 3 4 5 6 7 8 9 10
14
Part# HAMDRU175 HAMDRU314 HAMDRU322B HAMDRU316D HAMDRU315A HAMDRU321-0 HAMDRU321-A HAMDRU321-B N14 W14
Description Hammer-drum Shaft Hammer-drum Plates Hardened Hammer Rod Hard Faced Hammers 1/2” Hammer Spacers Hammer Drum Spacer 3 Ga (¼”) Hammer Drum Spacer 20 Ga Hammer Drum Spacer 10 Ga Shaft Nut Shaft Washer
QTY 1 26 3 150 150 127 25 25 2 2
Item
Description
7
Part# DUSCOL359 HM30118 HM30119 DUSCOL409 HM30120 HM30144 HM40208
8
DUSCOL406
Adapter Sleeve
9
SD-175
SD 1¾” Bushing
10
HM30139
Blower Fan Center
11
HM30138
Fan Paddle
12
HM30117
Dust Collector Spacer 1/4”
13
HM30117-2
Dust Collector Spacer 1/8”
14
Bolt
3/8”-16 X 5¾” Bolt
15
Nut
3/8” lock-nut
1 2 3 4 5 6
Transition pc. Dust Collector Back plate Dust Collector Band Cut-Off Plate Dust Collector Front Plate Dust Collector Cover Small H.M. Cyclone 24”
QTY 1 1 1 1 1 1 1 1 1 1 3 2 1 12 10
15
10 10
2
3
11
13
12
8
2
7
9
1
Gose to hand Pump Gose to Side Discharge Auger Cylinder
A
5
7 6
3 4
6 Item 1 2 3 4 5 6 7 8 9 10 11
16
12 13
Part# HE-12180 HC-2X8-STR HV-30006 JP-4MJ-4MP PB-4MP-6MB HAND-FEE HAND-DIS JB-4MJ-4MB90 Bolt Bolt Nut BB-6MB-8FB HF-8-SAE
5
Hyd. Hand Pump. 2” X 8” Stroke 1¼” Rod 1/4” 3 way ball valve #4 Male JIC - #4 Male Pipe Adapter #4 Male Pipe - #6 Male Boss Adapter Hose from Hand Pump to Feed Auger Cylinder Hose from Hand Pump to Discharge Auger Cylinder #4 Male JIC - #6 Male Boss 90 degree Adapter 3/4” x 3½” Machine Bolt 3/4” NC Stover Lock Nut #6 Male Boss - #8 Female Boss Adapter #8 SAE Breather Plug
A
4
Description
3/4” x 4½” Machine Bolt
4
1
Side Discharge Auger Cylinder QTY 1 2 2 2 2 1 1 1 1 1 2 1 1
Item 1 2 3 4 5 6 7
Part# HC-1512B Bolt NUT PIN JP-4MJ-4MP HAND-DIS PP-.25B
Description 1½” X 12” Hyd Cylinder w/Adj Clevis 3/4” x 3½” Machine Bolt 3/4” NC Stover Lock Nut 5/8” X 2½” #4 Male JIC - #4 Male Pipe Adapter Hose from Hand Pump to Discharge Auger Cylinder 1/4” Breather Vent
QTY 1 1 1 1 1 1 1
17
Hopper Spinner Motor 10
14
Tractor ends
15
6 10
10
12
13
10
17
14
5
11
10
16
10
8
10
11
10
18
12
12 11
This flow control is mounted on the side of the Front Shield
1
12
3
13
2
9
1
3
14
This flow control is 13mounted on the Feed Auger
3
2
1 2
7
4 5
1
13
6 7 8 9
7
3
9
3
8
5
8 Item
3
These 3 Hoses go to the hyd. motor on top of 2the Feed auger
13
3
4
10 11 12 13 14
7 6 8
3 1
18
15 16 17 18
Part#
HV-30003 TF-8FP-8FP-8MP JP-8MJ-8MP JP-8MJ-8MP-45 FEEAUG457 FEEAUG456 HYD HOSE HYD HOSE JP-8MJ-8MP-90 JB-8MJ-8MB HYD HOSE HYD HOSE HYD HOSE QC-28881 HM-01015 MB-875 HM-01012 FEEAUG473
Description HFV-3 Port Flow Control Valve 5602 Adapter #8 Male JIC - #8 Male Pipe Adapter #8 Male JIC - #8 Male Pipe 45° Adapter Hyd. Hose (Flow Control - Bottom of Motor) Hyd. Hose (Flow Control - Top of Motor) Hyd. Hose (Connecting two flow controls) Hyd. Hose (Feed Auger To Tractor) #8 Male JIC - #8 Male Pipe 90° Adapter #8 Male JIC - #8 Male Boss Hyd. Hose (Spinner Motor - Flow Control) Hyd. Hose (Flow Control - Spinner Motor) Hyd. Hose (Return to To Tractor) Quick Connect Male 101-1015 Char-lynn Or Eagle Motor 7/8” Hose Holder 101-1012 Char-Lynn Motor Motor Mount
QTY 2 2 6 1 1 1 1 1 1 4 1 1 1 2 1 4 1 1
3
19
3 5 6
4
5
4 2 7 Item 1
12 9
8
2 3
11
4
13
5 6 7 8 9 10
10
11 12
Part# HM40542 FEEAUG161 FEEAUG162 COLLAR1.500SS Bolt Lock Washer FEEAUG163 FEEAUG311 HM40571 FEEAUG159-1 COLLAR2.00SS SP153
Description Feed Auger Mounting Arm Auger Holder T Mounting Shaft 1-1/2” Single Split Collar ½’’-12 X 1¼” Bolt ¼” Lock Washer Placement Collar Cylinder Holder Bracket Mounting Arm Shaft Half Moon Placement Plate 2” Single Split Collar 1-3/4” Single Split Collar
QTY 1 1 1 2 2 2 1 1 1 1 1 1
1
20
21
1 2 7
3 4
14A
5
8 9
6
Item
Description
8 9
FEEAUG449
Top Plate
10
FEEAUG441
Main Auger Tube
11
FEEAUG448
Feed Auger Auger
12
FEEAUG445
Half Moon Holders
13
FEEAUG446
Flow Control Mount
14
FEEAUG444
60° Discharge Spout
15
FEEAUG420
Top Mounting Bracket
16
FEEAUG421
Middle Mounting Bracket
17
FEEAUG447
Bottom Mounting Bracket
18
MB-875
7/8” Hose Holder
1
12
14
Part# HM-01012 FEEAUG473 C5016X1 C5016 C5016X1-1/8 KEY W- Key FB-11250
2 3 4 5
10 12
6
12
7
13
11
12
15 12
16
101-1012 Char-Lynn Motor Motor Mount1 Coupling Chain # 1’’ Bore Coupling Chain #50 Coupling Chain # 1-1/8’’ Bore ¼” x ¼” Key 1” x ¼” Woodruff Key 1-1/8” Three Holed Flange Bearing
QTY 1 1 1 1 1 1 1 1 1 1 1 6 1 1 1 1 1 5
12 18
17
22
23
9
10
1 2
8
7
3
6
8
4
1
10
9
6
2
5
9 6
3
14
13
9
11
12
5
10
11
7 4 Item 1
Item 1 2 3 4 5 6 7 8 9 10 11
24
Part# FEEAUG455 FEEAUG442 FEEAUG19774 FEEAUG450 FEEAUG452 LSUNY12 FEEAUG462 2001400 MSC-00250449 FEEAUG463 FB-12500
Description Auger Guard Bottom tube Auger Holder Basket Short Feed Auger Hopper Holder Arm Yoke with spline Knuckle Bracket Weasler 14 series Yoke Cross Bearing Kit Snap Latch Lid 1¼” Bearing
QTY 1 1 1 1 1 1 1 1 1 1 1
2 3 4 5 6 7 8 9 10 11 12 13 14
Part# SA1240 SA1231 SA1232 SA1241 SA1243 SA1252 FB-12500 HM40588 HM40587 SA1246 SA1247 LSC159 LSC158 LSC157
Description Top Discharge Auger Top Tube Top Discharge Discharge Spout Discharge Auger Rest Top Plate 1¼” Bearing Swivel Ring Swivel Ring Side Plates Half Moon Mounting Strips Top U Bracket Hold-Down Strap Hook Hold-Down Strap U Bracket Hold-Down Strap
QTY 1 1 1 1 1 1 1 1 4 2 1 1 1 1
25
25 23
1
24
4
Item 1
4
2
3
3 4 5
5
6 7 8 9 10 11
6
12 13 14
11
10
8
9
15
7
16 17 18
2
20 21
21 15 12
19
22
13
23 24 25
27 14 26 17 18 20 19
16
26 27
Part# SA1222 SA1221 SA1250 SA1241 SA1254 DISAUG393 BOTAUG133 FB-175HM PUL5V6.3.2 5VX510 SK-1750 SIDA722 Washers PULID5X2.00 Bolt SA1230 DISAUG363 PUL5V6.7.2 Key SK-1375 Key SIDA720 UCPA208-24 SA1249 SA1255
Description
BOTAUG452-2 BOTAUG452-2
3/16” Spacer Washer
Base Discharge Tube Side Auger Base Bottom Discharge Auger Half Moon Mounting Strips Bottom Cylinder Mount U Clean-out Hole Cover Bottom Auger End Plate ¾” Piloted Flange Bearing w/ Eccentric Locking Collar 5V 2 Groove 6.3” Pulley 5VX 510 Belt SK 1¾” Bushing Rear Belt Shield Stack of 5/8” Washers Idler Pulley 5’’ by 2’’ w/ 5/8’’ ID 5/8” Machine Bolt Gear Box Mount Plate Small Gear Box (Medium Arm) 5V 2 Groove 6.7” Pulley 5/16” X 5/16” Key SK 1-3/8” Bushing 3/8” X 3/8” Key Gear Box Cover/ Skid Plate 1½” Taped Base, Pillow Block Bearing Auger Support Splined Top Auger Drive Shaft 1/4” Spacer Washer
QTY 1 1 1 1 1 1 1 1 1 2 1 1 ? 1 1 1 1 1 1 1 1 1 1 1 1 4 4
22
26
27
28