PRECISION CUT
The Tree that Started
GOLDEN EAGLE GANG SAW SYSTEM
90′ TIMBERJACK 240A
1990 Timberjack 240A
“Precision Under Pressure”
cable Skidder that’s working daily. Has a 5.9 cummins engine. Both the engine and transmission were rebuilt in 2021 with paperwork showing the work. Winch transfer case was also rebuilt shortly after. Pins and bushings are all tight, and is woods ready. Call/ Email for more information. Item ID 5082. Austin x703
1996 TIMBERJACK 380C
1996 Timberjack 380C 5.9
Cummins, 4 speed Clark
Transmission 4 forward, 4 reverse, chains all around, new cable, new steering pins, have new center pins in box current pins are fine. Minor leaks, good running machine. Item ID 4825. Austin x703
02′ JOHN DEERE 640G2
2002 John Deere 640G2 Cable skidder with 14000 frame hours, has new motor in it with less than 200 hours on it, and the transmission was rebuilt around the same time. Has all new bearings in the front end, as well
13428 Victory Ln. // PO Box 124 Adams Center, NY 13606
‘83 John Deere 4850
Item ID: Contact: Ph:
with 1700 hours, in very good condition. Easily produces high quality chips with patented ‘Cone’ drum design. Can easily load 42’ vans and produce 6 - 8 loads per day. Item ID 13882. Austin x703
Brewco Saws - Two Brewco Saws in excellent condition. Runs great. Item ID 13644. Sam x702
2010 Shop Built Wood Processor -It has a 353 Detroit diesel, 40 inch insert tooth circle saw, 30 foot
as a new seat, new gauges, new heater, new glass, and new lights. Has 23.1’s on it with brand new chains on the front. On a job now. Call for more info.
Item ID 4710. Austin x703
86′ TIMBERJACK 230A
‘16 Halverson H140 Skidsteer (DEMO)
Item ID: JW-909632
Contact: J Williams
Ph: (888) 401-6367 x701
Motor rebuilt about 10 hrs ago, Same with brakes and new clutch / pressure plate (10hrs ago), This is in good conditions, NOT old junk. It’s good to go to work, Owner for 10+yrs, and used for jobs here and there, been the family skidder, Can take videos of it if you can’t go
‘13 KMC 2500 Track
Item ID: 14078
Contact: Austin
Ph: (888) 401-6367 x703
off onto a conveyor. This is a very well built processor. Item ID 13820. Sam x702
look at it, Can help trucking it anywhere in the US, About 80mi south of Baltimore, MD
Item ID 3605. Joe x709
‘93 Barko 180B
FRANKLIN 170 SKIDDER
Item ID: 14077
Contact: Austin Ph: (888) 401-6367 x703
Detroit 453 engine, Powershift, 4 speed, Winch works well, Tires size: 23.1, Center section good, Runs and operates as it should Item ID 3517. Joe x709
98′ JOHN DEERE 640E
1998 John Deere 640E cable skidder with 10000 original hours, this skidder was bought directly from the original owner/ operator. Everything works like it should. Call for more info.
Item ID 2701. Austin x703
98′ JOHN DEERE 640G
98ʹ Model John Deere 640G with 10000 original hours, very straight skidder that was bought from the original owner/operator, everything works like it should. Call for more info.
capacity!. Item ID 13421. Sam x702 BARKO
1994 Barko 160B - Electric knuckleboom, 30' boom, 75hp motor, Rotobec continuous
Item ID 2694. Austin x703
‘05
Gehl CTL 70
Item ID: JW-986495
Contact: J Williams Ph: (888) 401-6367 x701
Firewood Processor - This is a Chomper Model 16 PDA automatice firewood processor with John Deere power unit with low hours. Control panel includes tach, oil pressure, water temp and amp gauges. Cuts logs up to 16”.
on injection pump. always started good. in good working order. 22in
1999 Barko 160D - new engine with meter dont work. The last 2 owners have only used it to load trucks or as a backup as needed. Has a CTR delimber, grapple has been rebuilt. Boom cylinders have minor leaks. a brand new Duetz engine. Lever control, 33” bar, pump and tranny ‘95 John Deere C6
JOHN DEERE 440C’S PACKAGE DEAL
“Precision Under Pressure”
Up for sale are two John Deere 440C Cable skidders, one is in great shape, winch just totally rebuilt and and working daily. The other has the transmission out of it, the trans has been rebuilt, but has not been put back in the skidder. Call for more info.
www.empirehyd.com Email info@empirehyd.com
hours ago, motor is strong with no blow by. Tight and has been well maintained. Call/Email for more information.
Item ID 5582. Austin x703
FMC 210
Item ID 1966. Austin x703
1983 JOHN DEERE 640C
John Deere 640C grapple skidder, has rebuilt transmission less than 200
FMC 210 CA 5250 track skidder, needs the transmission rebuilt. It has a 653 Detroit motor in it with low hours. Skidder was refurbished in 1089 used in a handful of logging jobs in the early 90’s followed by light service in shot in 2018. Call/Email for more
information.
Item ID 5526. Austin x703
CAT 225LC EXCAVATOR
Cat 225 machine starts right up, and has no big leaks. Will include a 28” and 48” bucket, also will include set of grapples. Call for more information.
‘16 Halverson H140 Skidsteer (DEMO)
Item ID: JW-909632
Item ID 5419. Austin x703
Contact: J Williams Ph: (888) 401-6367 x701
06′ JOHN DEERE 335 LOG LOADER
Motor has brand new pump. Does not smoke at all, New manifold, Brakes and lights all work, A/C – heat work
well, Machine is dry, has no leaks, Boom is strong. Fast loader, Turn bearings are good, Owner’s health is causing him to sell it, Delivery available as well. Buyer pays for trucking, About 70mi west of Orlando FL Item ID 5403. Joe x709
‘93 Barko 180B
Item ID: 14077
Contact: Austin Ph: (888) 401-6367 x703
TAJFUN EQUIPMENT
Lumbermens is a proud dealer for Tajfun equipment, from logging winches, to cranes, to firewood processors, Tajfun machinery makes high quality equipment. Call us for more information and a competitive quote today!
with 1700 hours, in very good condition. Easily produces high quality chips with patented ‘Cone’ drum design. Can easily load 42’ vans and produce 6 - 8 loads per day. Item ID 13882. Austin x703
Brewco Saws - Two Brewco Saws in excellent condition. Runs great.
Item ID
2010 Shop Built Wood Processor
-It has a 353 Detroit diesel, 40 inch insert tooth circle saw, 30 foot
Item ID 5368. Austin x703
‘95 John Deere C6 Tree Farmer
2022 TIGERCAT 620H
Item ID: 13920
Contact: Austin Ph: (888)
2022 Model Tigercat 620H grapple skidder with 660 original hours, has bogie grapple on it. 35ʺ tires, and Canadian light package, and camera in front on the grill. Skidder is in excellent shape. Call/Email for more information.
well built processor. Item ID 13820. capacity!. Item ID 13421. Sam x702 BARKO
Item ID 5334. Austin x703
1994 Barko 160B - Electric knuckleboom, 30' boom, 75hp motor, Rotobec continuous on injection pump. always started good. in good working order. 22in
- new engine with meter dont work. The last 2 owners have only used it to load trucks or as a backup as needed. Has a CTR delimber, grapple has been rebuilt. Boom cylinders have minor leaks. a brand new Duetz engine. Lever control, 33” bar, pump and tranny
‘13 KMC 2500 Track
13644. Sam x702
1999 Barko 160D
TIMBERJACK 1010
Timberjack 1010 double bunk forwarder, machine has around 15000 frame hours, and has had a lot of recent work done to it. That work includes: New Reman Perkins engine, New Radiator, Rebuilt Clark 3 speed tranny, Brand new bushings and pins in center section, rebuilt cylinders in boom and in the steering, New set of sure grip grapples, new seals in driveline. It will come with a set of eco tracks for the back, and set of wheel track for the front which are brand new. This is a straight machine that is not bent or busted up. It has had the same owner/operator since it had 6000 original hours on it. Owner is only selling to retire. Call/Email for more information.
“Precision Under Pressure”
works like it should.
Item ID 5320. Austin x703
Email info@empirehyd.com
CAT 538
2020 Cat 538 log loader with 2800 hours on it, still has warranty available. Working daily. Call for more information.
Item ID 5302. Austin x703
TIMBCO 445EXL
Timbco 445Exl with 8500 original hours, in excellent condition. Machine has been well maintained and serviced. Needs nothing, working daily. Call/Email for more information.
Item ID 5293. Austin x703
2016 TAJFUN 400 JOY
‘16 Halverson H140 Skidsteer (DEMO)
Item ID: JW-909632
Contact: J Williams
Ph: (888) 401-6367 x701
machine is working daily and is averaging 300 cords a week currently. Owner is only selling to upgrade to a brand new machine. Recent work includes a new ECU, new injectors, new fuel pump, new fuel lines, new wiring harness, new chip, new rear window, all new head cylinders, and pins/bushings, new encoders, and new seal kits. Head is super tight and has a new measuring wheel, and new rotator. Everything on the machine works as it should and currently has 24000 hours.
Item ID 5199. Austin x703
PRENTICE 210B
Item ID 5358. Austin x703
TIMBERJACK 208
208 Timberjack for sale, skidder is pretty solid all around, has a couple leaks, but motor fires right up every time. Has new starter, everything else on it
13428 Victory Ln. // PO Box 124 Adams Center, NY 13606
2016 Tajfun 400 Joy firewood processor, unit includes log lift, and outfeed conveyer. Machine has been a one owner/one operator unit since new and is in excellent condition. Call/ Email for more information.
Item ID 5227. Austin x703
TIMBERJACK 1270
2003 Timberjack 1270 Processor,
with 1700 hours, in very good condition. Easily produces high quality chips with patented ‘Cone’ drum design. Can easily load 42’ vans and produce 6 - 8 loads per day. Item ID 13882. Austin x703
mobile wheeled excavator with 9300 hours, equipped with newer Ryans saw head attachment. Both in good condition, the excavator has all new hoses, good tires, new lights, and back up camera. The Ryans head has low hours as well.
‘93 Barko 180B
Item ID: 14077
Contact: Austin Ph: (888) 401-6367 x703
Item ID 4979. Austin x703
13′ BARKO 595ML MAGNUM
2013 Barko 595 Magnum loader has 11000 original hours, equipped with 264 Csi delimber. Recently had two of the pumps rebuilt. Good, solid loader everything on it works as it should. Call/Email for more information.
‘95 John Deere C6 Tree Farmer
Item ID 4974. Austin x703
Item ID: 13920
‘13 KMC 2500 Track Skidder
Item ID: 14078
210B Prentice Knuckleboom, comes with reversible csi bucksaw. Works everyday, has joystick control, all new hoses on the boom, brand new grapple as well. Pretty tight and good loader. Only thing it does need is brakes.
Contact: Austin
Item ID 5085. Austin x703
Ph: (888) 401-6367 x703
LIEBHERR A312 WITH RYANS HEAD
1998 Model Liebher A312
Contact: Austin
18′ JOHN DEERE 753J
Ph: (888) 401-6367 x703
2018 John Deere 753J with 6000 original hours. Ready to work, only selling to downsize. Has good undercarriage, and hotsaw head. Call/Email for more information.
off onto a conveyor. This is a very well built processor. Item ID 13820. capacity!. Item ID 13421. Sam x702 BARKO
Item ID 4968. Austin x703
1994 Barko 160B - Electric knuckleboom, 30' boom, 75hp motor, Rotobec continuous good. in good working order. 22in 1999
160D -
meter dont work. The last 2 owners have only used it to load trucks or as a backup as needed. Has a CTR delimber, grapple has been rebuilt. Boom cylinders have minor leaks.
33” bar, pump and tranny
Brewco Saws - Two Brewco Saws in excellent condition. Runs great. Item ID 13644. Sam x702
2010 Shop Built Wood Processor -It has a 353 Detroit diesel, 40 inch insert tooth circle saw, 30 foot
Barko
new engine with
BELL SUPER T CUTTER
Bell Super T 3 wheel machine, has the deutz air cooled engine, with a 30” dangle head. Inside the cab it has levers for controls, and does also have air conditioning. Tires are size 28L and will come with chains as well. Overall in good condition, and ready to work. Call/Email for more information.
“Precision Under Pressure”
Item ID 4952. Austin x703
CAT D5H TSK
Cat D5h TSK track Skidder with 3700 original hours, 32” pads, and good undercarriage at around 80%. Ready to work. Call/Email for more information.
Item ID 4939. Austin x703
643J
2007 643J cutter with 12,700 hrs, thinning saw head, 28LX26 tires, new starter,batteries, alt, gear box rebuilt, motor runs great uses no oil, does have a Hydraulic leak or 2, needs a bushing in one of cylinder arms, also comes with a 843J parts machine, has a tpost saw
head,motor and Hydraulics are good 30k for both
Item ID 4907. Austin x703
04′ TIGERCAT 620
2004 Tigercat 620 Tigercat Grapple skidder has brand new engine in it, with less than 10 hours on it, and comes with a year warranty. Machine itself is pretty tight, speed control valve is new, main pumps are fairly new as well. Has heat/Ac, every function on the skidder works. Call for more info.
Item ID 4705 . Austin x703
TIMBCO 425D
Timbco 425D – Year 2001 –Quadco 20 360 degree head – 8.3 Cummins – Hours 7000 / 300 hours on caterpillar undercarriage – new planetary spindle. bearings and one seals in both sides.
13428 Victory Ln. // PO Box 124 Adams Center, NY 13606
Item ID 1429. Austin x703
725B TIMBERPRO
Well Maintained machine, tight and dry work ready with a Rolly II head. make an offer! Call for
more pictures.
Item ID 1398. Austin x703
’92 TIMBERJACK 450C
‘16 Halverson H140 Skidsteer (DEMO)
Item ID: JW-909632
10K frame hours – single arch – power-shift trans – tire size 28Ls – Tire tread: 20% front, 70% back – 5.9 cummins –Winch works – center section is tight – no major slack, dry machine, no leaks Item ID 1369.
Contact: J Williams Ph: (888) 401-6367 x701
Robert (606) 875-4783
TIGERCAT 822
Item ID 1130. Austin x703
460 TIMBERJACK
New Motor, new center pins, and Hyd Pump Cummins = 100hours on the new parts , Tires are at 60%, comes with a spare tire. Text or email for more pictures
‘13 KMC 2500 Track Skidder
Item ID: 14078
Item ID 1124. Marcus (660) 833-9061
Contact: Austin Ph: (888) 401-6367 x703
2009 JOHN DEERE 548G3
2009 John Deere 548G3 with 7700 original frame hours, skidder is tight, and has a new engine in it with less than 400
off onto a conveyor. This is a very well built processor. Item ID 13820.
Sam x702
‘05
Gehl CTL 70
Item ID: JW-986495
‘83 John Deere 4850
Item ID: Contact: Ph:
with 1700 hours, in very good condition. Easily produces high quality chips with patented ‘Cone’ drum design. Can easily load 42’ vans and produce 6 - 8 loads per day. Item ID 13882. Austin x703
Brewco Saws - Two Brewco Saws in excellent condition. Runs great.
Contact: J Williams Ph: (888) 401-6367 x701
Item ID 13644. Sam x702
FIREWOOD PROCESSORS
2010 Shop Built Wood Processor
-It has a 353 Detroit diesel, 40 inch insert tooth circle saw, 30 foot
chain conveyer, 8 way splitter, on 20,000lb goose neck trailer. Item ID 13916. Austin x703
Best Value Portable Log Splitter
-Small manufacturer in PA has made the best valued log splitter. Handles logs up to 32”. Uses 13HP Honda motor. Manual start but electronic option is available. Has Log Lift. Uses 4-way wedge adjustable to single two way. Great Value! PA. Item ID 12062. Sam x702
Manufacturing a full line of biomass fired combustion systems backed with fifty years of innovative clean-burn design. Diverse in every way with multi-fuel blending capability. Hurst stokers utilize hundreds of common and abundant solid biomass fuels. Large or small scale, project management is eased with the impressively short installation time required with prefabricated modular components. with
Firewood Processor - This is a Chomper Model 16 PDA automatice firewood processor with John Deere power unit with low hours. Control panel includes tach, oil pressure, water temp and amp gauges. Cuts logs up to 16”. One owner and comes with all manuals and receipts. Purchased new for $32,500. Item ID 13865.
Sam x702
LOGGING EQUIPMENT BANDIT
hours on it. New 28L tires, Everything on the machine works like it should. Call for more info.
Item ID 4699. Austin x703
‘93 Barko
180B
14′ JOHN DEERE 748H
Item ID: 14077
Contact: Austin Ph: (888) 401-6367 x703
2014 John Deere 748H model with 15000 frame hours, everything works like it should. Recently had new pins and bushings, and new motor installed just over a year ago. Equipped with sweda axles. Call for more info.
Item ID 2707. Austin x703
2016 HYPRO 755HB PROCESSOR
‘95 John Deere C6 Tree Farmer
Item ID: 13920
Contact: Austin Ph: (888) 401-6367 x703
Firewood Processor - This is a homemade processor with a 10’ log deck. Has a hydraulic grapple, chain and kicker that all runs off of a 4 cylinder Mercedes power unit. Has a 4’ chain saw that kicks
1999 Bandit 1900 Tracked Disc Chipper - Cat Under Carriage at 50% or better. 475 hp Cummins Diesel. 7500 Hours. One owner. Well maintained. Item ID 13294.
Sam x702
2004 Bandit Beast Model 46803412 Caterpillar Diesel engine with 850 HP. 5300 hrs. Mill in good condition. Just finished 10 Acre clearing job, ready to work! Remote control. Big production
Tractor is a 1985 Versatile 276 tractor that has a flex plate between the engine and pumps, equipped with skid plate under the engine, and some new lights. Engine is a 140HP cummins, and has 3200 hours on it. The Hypro only has 350 hours on it and is in great shape. Call for more information
capacity!. Item ID 13421. Sam x702 BARKO
1994 Barko 160B - Electric knuckleboom, 30' boom, 75hp motor, Rotobec continuous grapple, 5,000 original hours. (excellent condition.). Item ID 13238. Chris x700
Item ID 2593. Austin x703
1995 Barko 775 B Feller Buncher -Pumps recently redone. 400 hrs on injection pump. always started good. in good working order. 22in kohing head. head works great. Item ID 13185. Sam x702
1999 Barko 160D - new engine with approximately 1500 hours. Hour meter dont work. The last 2 owners have only used it to load trucks or as a backup as needed. Has a CTR delimber, grapple has been rebuilt. Boom cylinders have minor leaks. Item ID 13694. Sam x702
94 Barko 275 - Excellent value with low at hours at 3,500. 5.9 CUMMINS continuous grapple. Runs Great!. Item ID 13740. Sam x702
BELL
1990 Bell Super T - This Bell has a brand new Duetz engine. Lever control, 33” bar, pump and tranny
Tough Meets QUALITY
1979 TIMBERJACK 230 CABLE SKIDDER
“Precision Under Pressure”
1979 Timberjack 230 Cable Skidder. Starts and runs perfect. Excellet condition, Excellent tires. Eaton Winch, Straight Blade. Call for more pictures.
Item ID 1072.
Kyle (807) 631-4081
LOG LOADER EXCAVATOR 225 LC
1986 Caterpillar excavator with a 3208 engine 5000 hours, total hours is 19000, Grapple, heals, bucket.
Item ID 1067.
Mose (208) 290-1888
PRENTICE 384 KNUCKLEBOOM LOADER
2002 prentice 384 Knuckleboom. Saw not included. Mounted on ’89 S 2500 International truck. Knuckleboom carrier/trailer also available.
Item ID 978. Austin x703
reverse, external tranny cooler, 28L’s, tranny less than 1000 hours, motor redone no blow by, centers redone recent, no leaks, dry very minor seep on valve body and grapple controls. Rear ends redone a year ago, full time 4 wheel drive, John Deere winch, good winch, strong winch! Call for more pictures!
Item ID 863. Sam x702
JOHN DEERE 648D
new main drive shaft, motor rebuilt 200 or so hours ago, rebuilt fuel injector, hydraulic rebuilt, grapple rebuilt, w/ winch single arch tight machine 60% rear 40% front 28l’s
Item ID 547. Sam x702
JD 550G CRAWLER DOZER
Buyer pays for trucking, About 50mi south of Cincinnati OH Item ID 5388. Joe x709
16′ JD 700K
‘16 Halverson H140 Skidsteer (DEMO)
Item ID: JW-909632
Contact: J Williams
Ph: (888) 401-6367 x701
6 Way blade, Fully Enclosed cab, Forestry Package with winch, Wide pads, A/C – heat work, Owner has had it sine purchase. Now done with his project. Got himself something else, smaller, All controls work as they should, These go for $170-$175K anywhere you look (for the year), and without a winch. This one has everything. Have a reliable trucker available. Buyer pays for trucking, About 150mi south of Louisville, KY Item ID 4343. Joe x709
06′ JD 700J LGP
12′ JD 550K LGP
Rollers sprockets, chain and pads all re-done about 75hrs ago, Just had a John Deere 4000hrs service, All fluids an upgrades are up to date, No issues, very clean, no leaksI’d say machine is mint, Tracks are 24 inches with a 10’2” wide blade, Brand new U/C, 95%, Forestry package with winch, Enclosed cab, A/C and heat works and everything else, Owner is going with a bigger dozer, Ready to go to work, really solid dozer! Information provided is to the best of our knowledge and what owners tell us
‘93 Barko
180B
Item ID: 14077
Contact: Austin
Ph: (888) 401-6367 x703
Item ID 3753. Joe x709
John Deere C6 Tree Farmer
14′ JD 650K LGP
13428 Victory Ln. // PO Box 124 Adams Center, NY 13606
TIMBERJACK 380C GRAPPLE SKIDDER
1994 timberjack 380C 5.9 Cummins, 12 valve, 4 speed Clark transmission 4 forward 4
New head gasket, Both final drives replaced, U/C tread: Approx. 75%, 20 inch pads, Direct drive, Pedal steer, Winch works well, it’s the JD 4000 series, Everything works as it should, This is his backup dozer, why he’s selling. Doesn’t need it much anymore, Delivery available as well.
‘83 John Deere 4850
Item ID: 14073
Contact: Austin
‘05
Gehl CTL 70
Item ID: JW-986495
Contact: J Williams Ph: (888) 401-6367 x701
Ph: (888) 401-6367 x703
with 1700 hours, in very good condition. Easily produces high quality chips with patented ‘Cone’ drum design. Can easily load 42’ vans and produce 6 - 8 loads per day. Item ID 13882. Austin x703 EDGERS & GANGS
Brewco Saws - Two Brewco Saws in excellent condition. Runs great. Item ID 13644. Sam x702
FIREWOOD PROCESSORS
2010 Shop Built Wood Processor
-It has a 353 Detroit diesel, 40 inch insert tooth circle saw, 30 foot
chain conveyer, 8 way splitter, on 20,000lb goose neck trailer. Item ID 13916. Austin x703
Best Value Portable Log Splitter
-Small manufacturer in PA has made the best valued log splitter. Handles logs up to 32”. Uses 13HP Honda motor. Manual start but electronic option is available. Has Log Lift. Uses 4-way wedge adjustable to single two way. Great Value! PA. Item ID 12062. Sam x702
Firewood Processor - This is a homemade processor with a 10’ log deck. Has a hydraulic grapple, chain and kicker that all runs off of a 4 cylinder Mercedes power unit. Has a 4’ chain saw that kicks
‘13 KMC 2500 Track Skidder
Item ID: 14078
Contact: Austin
Ph: (888) 401-6367 x703
Enclosed cab, Winch strong, New sprockets go with it, Undercarriage 55%, Has no mechanical issues, been taken care of, The owner is done with a project he bought it for, Have a reliable trucker available. Buyer pays for trucking, About 80mi south of Louisville, KY
ID: 13920
Austin Ph: (888) 401-6367 x703 LUMBERMEN’S Equipment Digest PO Box 1146
Columbia, TN 38402-1146 1-800-477-7606 Fax (931) 388-3564 www.lumbermenonline.com
Item ID 3787. Joe x709
off onto a conveyor. This is a very well built processor. Item ID 13820.
Sam x702
Firewood Processor - This is a Chomper Model 16 PDA automatice firewood processor with John Deere power unit with low hours. Control panel includes tach, oil pressure, water temp and amp gauges. Cuts logs up to 16”. One owner and comes with all manuals and receipts. Purchased new for $32,500. Item ID 13865.
Sam x702
LOGGING EQUIPMENT
1999 Bandit 1900 Tracked Disc Chipper - Cat Under Carriage at 50% or better. 475 hp Cummins Diesel. 7500 Hours. One owner. Well maintained. Item ID 13294. Sam x702
2004 Bandit Beast Model 46803412 Caterpillar Diesel engine with 850 HP. 5300 hrs. Mill in good condition. Just finished 10 Acre clearing job, ready to work! Remote control. Big production
29 inch pads, All bushings are tight, Dry, no leaks, Pre def emission delete engine turned up 20hp, Forestry package, Winch on it only been used about 600hrs, 10 foot 4 inch blade, Owner is retiring, Can help trucking it anywhere in the US, In the Fresno, OH area Item ID 3574. Joe x709
capacity!. Item ID 13421. Sam x702 BARKO
1994 Barko 160B - Electric knuckleboom, 30' boom, 75hp motor, Rotobec continuous grapple, 5,000 original hours. (excellent condition.). Item ID 13238. Chris x700 1995 Barko 775 B Feller Buncher -Pumps recently redone. 400 hrs on injection pump. always started good. in good working order. 22in kohing head. head works great.
1999 Barko 160D - new engine with approximately 1500 hours. Hour meter dont work. The last 2 owners have only used it to load trucks or as a backup as needed. Has a CTR delimber, grapple has been rebuilt. Boom cylinders have minor leaks.
94 Barko 275 - Excellent value with low at hours at 3,500. 5.9 CUMMINS continuous grapple. Runs Great!. Item ID 13740. Sam
1990 Bell Super
JD 550G LT
Mid 90’s model, Original hours, Forestry package with a winch. It pulls good, UC tread: about 70%, Nothing wrong whatsoever with dozer, Been well kept and used sporadically by him and his son, little jobs here and there, They’re buying a skidder with the money they get from this, why are they selling it, Have a reliable trucker available. Buyer pays for trucking, In KY, about 90mi. north of Nashville TN
The Tree that Started it All!
Since 1986, Lumbermens has published a monthly circular reaching sawmills, loggers, pallet makers, recyclers and industrial woodworking plants worldwide.
Item ID 3686. Joe x709
CAT D6K2
PUBLISHER
Woods Publishing
ADVERTISING SALES
2015 model in excellent condition, currently has 1750 hours, has enclosed cab with heat and air, undercarriage is around 75%, working daily. Call for more info
Morris Woods (888) 401-6367 ext. 704 morris@lumbermens.co
Item ID 1488. Austin x703
MARKETING DIRECTOR
92′ CAT D5H
in really MINT conditions, One original owner, used for local jobs, not a major operation, He’s now 70yrs old and he’s willing to sell. He’s using it for one more week or so to finish a little job he has left, Have a reliable trucker available. Buyer pays for trucking, About 40mi south of Nashville, TN
Item ID 4327. Joe x709
90′ JD 550G
Item ID 4678. Joe x709
John Williams (888) 401-6367 ext. 701 j@lumbermens.co
DESIGN DIRECTOR
04′ JD 450H
Donna Heninger
Wide tracks, limb raisers, AC/ Heat, all controls work, Dozer is
EQUIPMENT REPS
Sam Wall (888) 401-6367 ext. 702
He has all of the side cab screens and the rock guards, Winch is strong, New hydraulic pump, New transmission pump, New batteries, U/C is at about 60% tread, New front idler & track adjuster, Runs well, no issues, Direct drive, Been serviced regularly, all the paperwork avail., Owner is done with the project, letting it go, Have a reliable trucker available. Buyer pays for trucking, Better pictures avail. upon request, About 100mi south of Columbus, OH
Item ID 3873. Joe x709
with 1700 hours, in very good condition. Easily produces high quality chips with patented ‘Cone’ drum design. Can easily load 42’ vans and produce 6 - 8 loads per day. Item ID 13882. Austin x703
Brewco Saws - Two Brewco Saws in excellent condition. Runs great.
off onto a conveyor. This is a very well built processor. Item ID 13820.
capacity!. Item ID 13421. Sam x702 BARKO
1994 Barko 160B - Electric knuckleboom, 30' boom, 75hp motor, Rotobec continuous grapple, 5,000 original hours. (excellent condition.). Item ID
low hours. Control panel includes tach, oil pressure, water temp and
Reman Cummins Engine. Equipped with 18” Waratah High Speed Disc Saw. 28L x 26 Tires at 40% complete with chains. This machine has been extremely well maintained and runs very well. Hard to find them in this good of condition. Has a twin that is available if you need two units.
LOGGING EQUIPMENT BANDIT
1999 Bandit 1900 Tracked Disc Chipper - Cat Under Carriage at 50% or better. 475 hp Cummins Diesel. 7500 Hours. One owner. Well maintained. Item ID 13294.
Item ID 12524. Sam x702
Tracks. Front blade. Hood guard. Item ID 12267. Sam x702 2005 Valmet 941 Harvester - Totally refurbished head to toe! Very good running condition. Over $50,000 in recent updates and maintenance. New center pin bushings; new bogey seals; valves resealed; all cylinders packed. 10,200 hours. Largest of rubber tired harvesters. Has Valmet 370.2 processing head with less than 4000 hours. Engine
1995 Barko 775 B Feller Buncher -Pumps recently redone. 400 hrs on injection pump. always started good. in good working order. 22in kohing head. head works great. Item ID 13185. Sam x702
Barko 160D - new engine with approximately 1500 hours. Hour meter dont work. The last 2 owners have only used it to load trucks or as a backup as needed. Has a CTR delimber, grapple has been rebuilt. Boom cylinders have minor leaks.
work! Remote control. Big production
2005 Valmet 860.1 8-Wheeled Forwarder - 17,800 hours. New hydraulic transmission and gear box in 2013. $70,000 of updates in 2012. Bogies just resealed. Spare pump ($7,000 value) Good running condition. Sisu engine uses 4 gal/ hour. 16 ton capacity. One set of
370E Harvesting head just added in 2010 and has 7000 hours. 36” Triple Grouser tracks rebuilt one year ago and are at 80%. Sisu engine that is very stingy on fuel. 8’ squirt at end of boom for 30’ reach. Reversible fan and auxiliary oil cooler. Still runs OK. Cutting today but will needs some basic
Mud
** CALENDAR**
1992 TIMBERJACK 240 CABLE SKIDDER Item ID: 7478
Contact: WALKER
Email: Walker@lumbermensco.com
Phone: 888-401-6367 EXT 707
2005 TIGERCAT 240B LANDING LOADER Item ID: 7539
Contact: WALKER
Email: Walker@lumbermensco.com
Phone: 888-401-6367 EXT 707
Contact: WALKER
Email: Walker@lumbermensco.com Phone: 888-401-6367 EXT 707
‘83 John Deere 4850
Item ID: 14073
Contact: Austin Ph: (888) 401-6367 x703
with 1700 hours, in very good condition. Easily produces high quality chips with patented ‘Cone’ drum design. Can easily load 42’ vans and produce 6 - 8 loads per day. Item ID 13882. Austin x703
Brewco Saws - Two Brewco Saws in excellent condition. Runs great. Item ID 13644. Sam x702
FIREWOOD PROCESSORS
2010 Shop Built Wood Processor
-It has a 353 Detroit diesel, 40 inch insert tooth circle saw, 30 foot
Item ID: JW-909632
FRANKLIN 105 FELLER BUNCHER Item ID: 7470
Phone: 888-401-6367 EXT 707 2006 JOHN DEERE 755C CRAWLER LOADER Item ID: 7466 Contact: WALKER
Email:
Phone: 888-401-6367 EXT 707
‘05 Gehl CTL 70
Item ID: Contact: Ph:
chain conveyer, 8 way splitter, on 20,000lb goose neck trailer. Item ID 13916. Austin x703
Best Value Portable Log Splitter -Small manufacturer in PA has made the best valued log splitter. Handles logs up to 32”. Uses 13HP Honda motor. Manual start but electronic option is available. Has Log Lift. Uses 4-way wedge adjustable to single two way. Great Value! PA. Item ID 12062. Sam x702
Firewood Processor - This is a homemade processor with a 10’ log deck. Has a hydraulic grapple, chain and kicker that all runs off of a 4 cylinder Mercedes power unit. Has a 4’ chain saw that kicks
Contact: J Williams Ph: (888) 401-6367 x701
Contact: WALKER
Email: Walker@lumbermensco.com
Phone: 888-401-6367 EXT 707
Item ID: 14078
Contact: Austin Ph: (888) 401-6367 x703
off onto a conveyor. This is a very well built processor. Item ID 13820.
Sam x702
Firewood Processor - This is a Chomper Model 16 PDA automatice firewood processor with John Deere power unit with low hours. Control panel includes tach, oil pressure, water temp and amp gauges. Cuts logs up to 16”. One owner and comes with all manuals and receipts. Purchased new for $32,500. Item ID 13865.
Sam x702
LOGGING EQUIPMENT BANDIT
1999 Bandit 1900 Tracked Disc
Chipper - Cat Under Carriage at 50% or better. 475 hp Cummins Diesel. 7500 Hours. One owner. Well maintained. Item ID 13294.
Sam x702
2004 Bandit Beast Model 46803412 Caterpillar Diesel engine with 850 HP. 5300 hrs. Mill in good condition. Just finished 10 Acre clearing job, ready to work! Remote control. Big production
Contact: WALKER
Email: Walker@lumbermensco.com
capacity!. Item ID
Email:
1994 Barko 160B - Electric knuckleboom, 30' boom, 75hp motor, Rotobec continuous grapple, 5,000 original hours. on injection pump. always started good. in good working order. 22in kohing head. head works great. Item ID 13185. Sam x702
1999 Barko 160D - new engine with approximately 1500 hours. Hour meter dont work. The last 2 owners have only used it to load trucks or as a backup as needed. Has a CTR delimber, grapple has been rebuilt. Boom cylinders have minor leaks.
1990 Bell Super T - This Bell has a brand new Duetz engine. Lever control, 33” bar, pump and tranny
13421. Sam x702 BARKO
1995 TIMBCO 425B Item ID: 8030
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
2014 MORBARK NCL
MODEL 23 Item ID: 8024
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
Item ID: JW-909632
Contact: J Williams Ph: (888) 401-6367 x701
2011 JOHN DEERE 437D Item ID: 7999
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
Item ID: 14078
2015 JOHN DEERE 700K Item ID: 7968
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
2013 PRENTICE 2384 Item ID: 7961
13428 Victory Ln. // PO Box 124 Adams
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
‘83 John Deere 4850
Item ID: 14073
2017 TIGERCAT 630E Item ID: 7928
Contact: AUSTIN
2015 JOHN DEERE 643K Item ID: 7954
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
TIMBERJACK 240C Item ID: 7948
Contact: Austin Ph: (888) 401-6367 x703
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
off onto a conveyor. This is a very well built processor. Item ID 13820.
Sam x702
‘05 Gehl CTL 70
Item ID: Contact: Ph:
PRENTICE 410 Item ID: 7943
capacity!. Item ID 13421. Sam x702 BARKO
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029 2016 JOHN DEERE 344K WHEEL LOG LOADER Item ID: 7727
chain conveyer, 8 way splitter, on 20,000lb goose neck trailer. Item ID 13916. Austin x703
Contact: AUSTIN
Email: Austin@lumbermensco.com
Contact: Austin Ph: (888) 401-6367 x703
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
with 1700 hours, in very good condition. Easily produces high quality chips with patented ‘Cone’ drum design. Can easily load 42’ vans and produce 6 - 8 loads per day. Item ID 13882. Austin x703
Brewco Saws - Two Brewco Saws in excellent condition. Runs great. Item ID 13644. Sam x702
BELL ULTRA C FELLER BUNCHER Item ID: 7579
FIREWOOD PROCESSORS
Email: Austin@lumbermensco.com
Contact: AUSTIN
Firewood Processor - This is a Chomper Model 16 PDA automatice firewood processor with John Deere power unit with low hours. Control panel includes tach, oil pressure, water temp and amp gauges. Cuts logs up to 16”. One owner and comes with all manuals and receipts. Purchased new for $32,500. Item ID 13865.
Email: Austin@lumbermensco.com
1994 Barko 160B - Electric knuckleboom, 30' boom, 75hp motor, Rotobec continuous grapple, 5,000 original hours. (excellent condition.). Item ID 13238. Chris x700
1995 Barko 775 B Feller Buncher -Pumps recently redone. 400 hrs on injection pump. always started good. in good working order. 22in kohing head. head works great. Item ID 13185. Sam x702
Contact: AUSTIN
Email: Austin@lumbermensco.com
Best Value Portable Log Splitter
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
-Small manufacturer in PA has made the best valued log splitter. Handles logs up to 32”. Uses 13HP Honda motor. Manual start but electronic option is available. Has Log Lift. Uses 4-way wedge adjustable to single two way. Great Value! PA. Item ID 12062. Sam x702
PONSEE BUFFALO FORWARDER Item ID: 7575
Sam x702
Phone: 888-401-6367 EXT 703 (C) 931-797-8029 BARKO 275B TRACKED LOADER Item ID: 7660
LOGGING EQUIPMENT BANDIT
1999 Bandit 1900 Tracked Disc
Chipper - Cat Under Carriage at 50% or better. 475 hp Cummins Diesel. 7500 Hours. One owner. Well maintained. Item ID 13294.
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
1999 Barko 160D - new engine with approximately 1500 hours. Hour meter dont work. The last 2 owners have only used it to load trucks or as a backup as needed. Has a CTR delimber, grapple has been rebuilt. Boom cylinders have minor leaks.
Sam x702
VOLVO L150E WHEEL LOADER WITH LARGE GRAPPLE Item ID: 7532
2010 Shop Built Wood Processor
Contact: AUSTIN
Email: Austin@lumbermensco.com
Contact: AUSTIN
Email: Austin@lumbermensco.com
Contact: SAM
Email: Sam@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
-It has a 353 Detroit diesel, 40 inch insert tooth circle saw, 30 foot
Firewood Processor - This is a homemade processor with a 10’ log deck. Has a hydraulic grapple, chain and kicker that all runs off of a 4 cylinder Mercedes power unit. Has a 4’ chain saw that kicks
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
2004 Bandit Beast Model 46803412 Caterpillar Diesel engine with 850 HP. 5300 hrs. Mill in good condition. Just finished 10 Acre clearing job, ready to work! Remote control. Big production
Phone: 888-401-6367 EXT 702 (C) 615-596-4148
Runs Great!. Item ID 13740. Sam x702 BELL
Contact: WALKER
Email: Walker@lumbermensco.com
1990 Bell Super T - This Bell has a brand new Duetz engine. Lever control, 33” bar, pump and tranny
Phone: 888-401-6367 EXT 707 2023 DIAMOND MILLER STUMP GRINDER Item ID: 7477
‘95 John Deere C6
2001 BELL ULTRA T FELLER BUNCHER Item ID: 6965
JOHN DEERE 540G II CABLE SKIDDER Item ID: 5745
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
SKIDDER Item ID: 5045
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
8076
Contact: JOE
Email: Joe@lumbermensco.com
Contact: JOE
Email: Joe@lumbermensco.com
Phone: 888-401-6367 EXT 709 (C) 801-362-2170
Contact: JOE
Email: Joe@lumbermensco.com
Phone: 888-401-6367 EXT 709 (C) 801-362-2170
WOODSHOP EQUIPMENT FOR
SALE
Item ID: 7406
1. Nissan forklift with 4,975 hours has 42″ forks with side shifter
2. Foley below-planer Molder, blades included. 1989 model 804
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
2001 TJ 360 CABLE SKIDDER Item ID: 8136
Contact: JOE
Email: Joe@lumbermensco.com
1997 MODEL MORBARK 1200 TUB GRINDER Item ID: 5573
Contact: JOE
Email: Joe@lumbermensco.com
Phone: 888-401-6367 EXT 709 (C) 801-362-2170
& W 125 Band Mill with Caterpillar generator - Low hours on the mill, electronic computer Set works,1 1/2" or 2" band, 22ft. track Cat 3406 140KW Genset, 12,400 hours ready to run. Item ID 13434. Sam x702
3. Optima Scale pallet, Truck with built in scale. MODEL- OP-918W-5K 4. NEW TWB40 Tora Max Electric Walkie MODEL-TWB40. 5. 30″ Oliver Vertical Bandsaw 28″ x 26″ table. MODEL-217-S 6. Classic Fence w/standard rails, MODEL-W2005 7. NEW Custom movable fence for Oliver. 8. Tannewitz 30″ Bandsaw MODEL-PH 9. Kreg Bandsaw Fence
Phone: 888-401-6367 EXT 709 (C) 801-362-2170 Contact: WALKER
Email:
Phone: 888-401-6367 EXT 707
208 Item ID: 5320
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
MODEL-KMS7200 Carter products guide Assembly 10. Northfield No. 7 Surface Planer, 25″ SKH planer-15HP.DMD,8″ shavings hood with knife grinder/joining attachment; 2 manuals, RE-BUILT, 4-Knife cutterhead Knife set, Dialtype Knife & roll setting gauge 11. Diehl Rip saw with idle conveyor and manual, MODEL-SL52, 1970 PRE-OWNED W/IDLE conveyor & manual wrench 1.75″ open End, MODEL-482-0013 12. Hazel thorn Chop saw
Contact: WALKER
Email: Walker@lumbermensco.com
Phone: 888-401-6367 EXT 707
2022 TIMBERPRO 755D
Item ID: 7924
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
Email: Joe@lumbermensco.com Phone: 888-401-6367 EXT 709 (C) 801-362-2170
2005 JOHN DEERE 548G3 GRAPPLE SKIDDER Item ID: 7678
Contact: AUSTIN
Email: Austin@lumbermensco.com
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029 1990 JOHN DEERE 540B CABLE SKIDDER Item ID: 7327
Contact: JOE
Email: Joe@lumbermensco.com
Phone: 888-401-6367 EXT 709 (C) 801-362-2170
‘83 John Deere 4850
Item ID: 14073
Contact: JOE
13428 Victory Ln. // PO Box 124 Adams Center, NY 13606
‘16 Halverson H140 Skidsteer (DEMO)
Item ID: JW-909632
Contact: J Williams Ph: (888) 401-6367 x701
Phone: 888-401-6367 EXT 703 (C) 931-797-8029 2015 JOHN DEERE 648H GRAPPLE SKIDDER Item ID: 7599
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
2004 CAT 525B GRAPPLE SKIDDER Item ID: 7349
Contact: JOE
Email: Joe@lumbermensco.com
Phone: 888-401-6367 EXT 709 (C) 801-362-2170
Item
7253 Contact: JOE Email: Joe@lumbermensco.com Phone: 888-401-6367 EXT 709 (C) 801-362-2170
‘05 Gehl CTL 70
Item ID: Contact: Ph:
FRANKLIN 170 GRAPPLE SKIDDER Item ID: 5093
‘13 KMC 2500 Track Skidder
Item ID: 14078
Contact: Austin
JOHN DEERE 648H GRAPPLE SKIDDER
Item ID: 7245
Ph: (888) 401-6367 x703
Contact: JOE
Email: Joe@lumbermensco.com
Phone: 888-401-6367 EXT 709 (C) 801-362-2170
off onto a conveyor. This is a very well built processor. Item ID 13820.
Sam x702
2007 CAT 525C GRAPPLE SKIDDER Item ID: 6927
capacity!. Item ID 13421. Sam x702 BARKO
Contact: JOE
Email: Joe@lumbermensco.com
Phone: 888-401-6367 EXT 709 (C) 801-362-2170
Contact: Austin Ph: (888) 401-6367 x703
Email: Joe@lumbermensco.com
Phone: 888-401-6367 EXT 709 (C) 801-362-2170
Phone: 888-401-6367 EXT 709 (C) 801-362-2170 98′ JOHN DEERE 648G GRAPPLE SKIDDER Item ID: 4510
with 1700 hours, in very good condition. Easily produces high quality chips with patented ‘Cone’ drum design. Can easily load 42’ vans and produce 6 - 8 loads per day. Item ID 13882. Austin x703
Brewco Saws - Two Brewco Saws in excellent condition. Runs great. Item ID 13644. Sam x702
chain conveyer, 8 way splitter, on 20,000lb goose neck trailer. Item ID 13916. Austin x703
Contact: JOE
Email: Joe@lumbermensco.com
Best Value Portable Log Splitter
-Small manufacturer in PA has made the best valued log splitter. Handles logs up to 32”. Uses 13HP Honda motor. Manual start but electronic option is available. Has Log Lift. Uses 4-way wedge adjustable to single two way. Great Value! PA. Item ID 12062. Sam x702
H67 GRAPPLE SKIDDER Item ID: 4122
Contact: JOE
Firewood Processor - This is a Chomper Model 16 PDA automatice firewood processor with John Deere power unit with low hours. Control panel includes tach, oil pressure, water temp and amp gauges. Cuts logs up to 16”. One owner and comes with all manuals and receipts. Purchased new for $32,500. Item ID 13865.
Email: Joe@lumbermensco.com
Sam x702
Phone: 888-401-6367 EXT 709 (C) 801-362-2170
LOGGING EQUIPMENT BANDIT
1999 Bandit 1900 Tracked Disc
Chipper - Cat Under Carriage at 50% or better. 475 hp Cummins Diesel. 7500 Hours. One owner. Well maintained. Item ID 13294.
Sam x702
1994 Barko 160B - Electric knuckleboom, 30' boom, 75hp motor, Rotobec continuous grapple, 5,000 original hours. on injection pump. always started good. in good working order. 22in kohing head. head works great. Item ID 13185. Sam x702
JOHN DEERE 748H Item ID: 8038
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
1999 Barko 160D - new engine with approximately 1500 hours. Hour meter dont work. The last 2 owners have only used it to load trucks or as a backup as needed. Has a CTR delimber, grapple has been rebuilt. Boom cylinders have minor leaks.
1993 JOHN DEERE 540E Item ID: 8107
FIREWOOD PROCESSORS
2010 Shop Built Wood Processor
Contact: AUSTIN
Email: Austin@lumbermensco.com
-It has a 353 Detroit diesel, 40 inch insert tooth circle saw, 30 foot
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
Firewood Processor - This is a homemade processor with a 10’ log deck. Has a hydraulic grapple, chain and kicker that all runs off of a 4 cylinder Mercedes power unit. Has a 4’ chain saw that kicks
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
Contact: AUSTIN
Email: Austin@lumbermensco.com
2004 Bandit Beast Model 46803412 Caterpillar Diesel engine with 850 HP. 5300 hrs. Mill in good condition. Just finished 10 Acre clearing job, ready to work! Remote control. Big production
Contact: AUSTIN
Phone: 888-401-6367 EXT 703 (C) 931-797-8029 1997 CAT 515
Item ID: 8045
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
1990 Bell Super T - This Bell has a brand new Duetz engine. Lever control, 33” bar, pump and tranny
‘95 John Deere C6
1996 TIMBERJACK 380C Item ID: 4825
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
1997 TIMBERJACK 360C GRAPPLE SKIDDER Item ID: 7080
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
90′ TIMBERJACK 240A Item ID: 5082
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
JOHN DEERE 440C’S PACKAGE
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
FMC 210 Item ID: 5526
Contact: AUSTIN
Email: Austin@lumbermensco.com Phone: 888-401-6367 EXT 703 (C) 931-797-8029
JOHN DEERE 640C Item ID: 5582
Contact: AUSTIN
Email: Austin@lumbermensco.com Phone: 888-401-6367 EXT 703 (C) 931-797-8029
FRANKLIN 170 SKIDDER Item ID: 3517
Contact: JOE
Email: Joe@lumbermensco.com
Phone: 888-401-6367 EXT 709 (C) 801-362-2170
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
2001 CAT 517 SWING BOOM TRACK SKIDDER Item ID: 7286
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
JOHN DEERE 440C Item ID: 5242
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
1999 JOHN DEERE 640G CABLE SKIDDER Item ID: 7314
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
PRENTICE 210B Item ID: 5085
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
13428 Victory Ln. // PO Box 124 Adams Center, NY 13606
Contact: AUSTIN
Email: Austin@lumbermensco.com
BELL SUPER T CUTTER Item ID: 4952
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
‘83 John Deere 4850
Item ID: 14073
TIMBERJACK 1270 Item ID: 5199
Contact: Austin Ph: (888) 401-6367 x703
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
with 1700 hours, in very good condition. Easily produces high quality chips with patented ‘Cone’ drum design. Can easily load 42’ vans and produce 6 - 8 loads per day. Item ID 13882. Austin x703
Brewco Saws - Two Brewco Saws in excellent condition. Runs great. Item ID 13644. Sam x702
‘16 Halverson H140
Item ID: JW-909632
2022 TIGERCAT 620H Item ID: 5334
Contact: J Williams Ph: (888) 401-6367 x701
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
KMC 2500 Track
Item ID: 14078
Contact: Austin Ph: (888) 401-6367 x703
Contact: AUSTIN
Item ID: 5368
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
Email: Austin@lumbermensco.com
‘05 Gehl CTL 70
Item ID: Contact: Ph:
2016 TAJFUN 400 JOY Item ID: 5227
chain conveyer, 8 way splitter, on 20,000lb goose neck trailer. Item ID 13916. Austin x703
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029 13′ BARKO 595ML MAGNUM Item ID: 4974
off onto a conveyor. This is a very well built processor. Item ID 13820.
Sam x702
capacity!. Item ID 13421. Sam x702 BARKO
Contact: AUSTIN
Phone: 888-401-6367 EXT 703 (C) 931-797-8029 643J Item ID: 4907 TIMBERJACK 1010 Item ID: 5358
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
1994 Barko 160B - Electric knuckleboom, 30' boom, 75hp motor, Rotobec continuous grapple, 5,000 original hours.
Firewood Processor - This is a Chomper Model 16 PDA automatice firewood processor with John Deere power unit with low hours. Control panel includes tach, oil pressure, water temp and amp gauges. Cuts logs up to 16”. One owner and comes with all manuals and receipts. Purchased new for $32,500. Item ID 13865.
Contact: AUSTIN
Email: Austin@lumbermensco.com
1995 Barko 775 B Feller Buncher -Pumps recently redone. 400 hrs on injection pump. always started good. in good working order. 22in kohing head. head works great. Item ID 13185. Sam x702
Contact: AUSTIN
Email: Austin@lumbermensco.com
Best Value Portable Log Splitter
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
-Small manufacturer in PA has made the best valued log splitter. Handles logs up to 32”. Uses 13HP Honda motor. Manual start but electronic option is available. Has Log Lift. Uses 4-way wedge adjustable to single two way. Great Value! PA. Item ID 12062. Sam x702
Sam x702
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
LOGGING EQUIPMENT BANDIT
1999 Bandit 1900 Tracked Disc
Chipper - Cat Under Carriage at 50% or better. 475 hp Cummins Diesel. 7500 Hours. One owner. Well maintained. Item ID 13294.
Sam x702
Phone: 888-401-6367 EXT 703 (C) 931-797-8029 CAT 538 Item ID: 5302
1999 Barko 160D - new engine with approximately 1500 hours. Hour meter dont work. The last 2 owners have only used it to load trucks or as a backup as needed. Has a CTR delimber, grapple has been rebuilt. Boom cylinders have minor leaks.
FIREWOOD PROCESSORS
04′ TIGERCAT 620 Item ID: 4705
18′ JOHN DEERE 753J Item ID: 4968
2010 Shop Built Wood Processor
Contact: AUSTIN
Email: Austin@lumbermensco.com
Contact: AUSTIN
Email: Austin@lumbermensco.com
Contact: AUSTIN
-It has a 353 Detroit diesel, 40 inch insert tooth circle saw, 30 foot
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
Firewood Processor - This is a homemade processor with a 10’ log deck. Has a hydraulic grapple, chain and kicker that all runs off of a 4 cylinder Mercedes power unit. Has a 4’ chain saw that kicks
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
2004 Bandit Beast Model 46803412 Caterpillar Diesel engine with 850 HP. 5300 hrs. Mill in good condition. Just finished 10 Acre clearing job, ready to work! Remote control. Big production
Phone: 888-401-6367 EXT 703 (C) 931-797-8029 CAT D5H TSK Item ID: 4939
CUMMINS continuous grapple. Runs Great!. Item ID 13740. Sam x702 BELL
TIMBCO 445EXL Item ID: 5293
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
1990 Bell Super T - This Bell has a brand new Duetz engine. Lever control, 33” bar, pump and tranny
‘95 John Deere C6
Email: Sam@lumbermensco.com
Phone: 888-401-6367 EXT 702 (C) 615-596-4148
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
16′ JD 700K Item ID: 4343
Contact: JOE
Email: Joe@lumbermensco.com
Phone: 888-401-6367 EXT 709 (C) 801-362-2170
2009 JOHN DEERE 540G3 CABLE SKIDDER Item ID: 7299
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
Item ID: 1067 2009 JOHN DEERE 548G3 Item ID: 4699
725B TIMBERPRO Item ID: 1398
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
2012 CAT 525C GRAPPLE SKIDDER Item ID: 7552
Contact: WALKER
Email: Walker@lumbermensco.com Phone: 888-401-6367 EXT 707
JOHN DEERE 748H Item ID: 2707
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
Contact: ROBERT Phone: 606-875-4783
2019 JOHN DEERE 648L2 GRAPPLE SKIDDER Item ID: 7308
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
JOHN DEERE 648D Item ID: 547
Contact: SAM
Email: Sam@lumbermensco.com
Phone: 888-401-6367 EXT 702 (C) 615-596-4148
JD 450H Item ID: 4327
Contact: JOE
Email: Joe@lumbermensco.com
Phone: 888-401-6367 EXT 709 (C) 801-362-2170
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
13428 Victory Ln. // PO Box 124 Adams Center, NY 13606
Contact: AUSTIN
Email: Austin@lumbermensco.com
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
Phone: 888-401-6367 EXT 703 (C) 931-797-8029 2015 INTERNATIONAL 5100
‘83 John Deere 4850
Item ID: 14073
PICKER TRUCK Item ID: 7070
Contact: AUSTIN
Contact: Austin Ph: (888) 401-6367 x703
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
with 1700 hours, in very good condition. Easily produces high quality chips with patented ‘Cone’ drum design. Can easily load 42’ vans and produce 6 - 8 loads per day. Item ID 13882. Austin x703
Brewco Saws - Two Brewco Saws in excellent condition. Runs great. Item ID 13644. Sam x702
FIREWOOD PROCESSORS
2010 Shop Built Wood Processor
‘05 Gehl CTL 70
Item ID: Contact: Ph: (888) 401-6367 x701
24C SAWHEAD Item ID: 7065
chain conveyer, 8 way splitter, on 20,000lb goose neck trailer. Item ID 13916. Austin x703
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
Best Value Portable Log Splitter
-Small manufacturer in PA has made the best valued log splitter. Handles logs up to 32”. Uses 13HP Honda motor. Manual start but electronic option is available. Has Log Lift. Uses 4-way wedge adjustable to single two way. Great Value! PA. Item ID 12062. Sam x702
‘16 Halverson H140
Item ID: JW-909632
Contact: J Williams Ph: (888) 401-6367 x701
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
Contact: JOE
Email: Joe@lumbermensco.com
‘13 KMC 2500 Track
Item ID: 14078
Contact: Austin Ph: (888) 401-6367 x703
Contact:
off onto a conveyor. This is a very well built processor. Item ID 13820.
Sam x702
Firewood Processor - This is a Chomper Model 16 PDA automatice firewood processor with John Deere power unit with low hours. Control panel includes tach, oil pressure, water temp and amp gauges. Cuts logs up to 16”. One owner and comes with all manuals and receipts. Purchased new for $32,500. Item ID 13865.
Email: Austin@lumbermensco.com
Sam x702
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
LOGGING EQUIPMENT BANDIT
1999 Bandit 1900 Tracked Disc
Chipper - Cat Under Carriage at 50% or better. 475 hp Cummins Diesel. 7500 Hours. One owner. Well maintained. Item ID 13294.
Sam x702
-It has a 353 Detroit diesel, 40 inch insert tooth circle saw, 30 foot
Firewood Processor - This is a homemade processor with a 10’ log deck. Has a hydraulic grapple, chain and kicker that all runs off of a 4 cylinder Mercedes power unit. Has a 4’ chain saw that kicks
Contact: JOE
Email: Joe@lumbermensco.com
‘95 John Deere C6
capacity!. Item ID 13421. Sam x702 BARKO
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
1994 Barko 160B - Electric knuckleboom, 30' boom, 75hp motor, Rotobec continuous grapple, 5,000 original hours.
1995 Barko 775 B Feller Buncher -Pumps recently redone. 400 hrs on injection pump. always started good. in good working order. 22in kohing head. head works great. Item ID 13185. Sam x702
Contact: JOE
Phone: 888-401-6367 EXT 709 (C) 801-362-2170 02′ CASE 650H Item ID: 3511 Contact:
Phone: 888-401-6367 EXT 709 (C) 801-362-2170 JD 550G LT Item ID: 3686
2004 Bandit Beast Model 46803412 Caterpillar Diesel engine with 850 HP. 5300 hrs. Mill in good condition. Just finished 10 Acre clearing job, ready to work! Remote control. Big production
Phone: 888-401-6367 EXT 709 (C) 801-362-2170 14' JD 650K LGP Item ID: 3574
Email: Joe@lumbermensco.com
1999 Barko 160D - new engine with approximately 1500 hours. Hour meter dont work. The last 2 owners have only used it to load trucks or as a backup as needed. Has a CTR delimber, grapple has been rebuilt. Boom cylinders have minor leaks.
Runs Great!. Item ID 13740. Sam x702 BELL
1990 Bell Super T - This Bell has a brand new Duetz engine. Lever control, 33” bar, pump and tranny
CAT D6K2 Item ID: 1488
Contact: JOE
Email: Joe@lumbermensco.com
Phone: 888-401-6367 EXT 709 (C) 801-362-2170
2004 JOHN DEERE 648G3 Item ID: 2628
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
888-401-6367 EXT 709 (C) 801-362-2170 13′ JD 648H Item ID: 3589
00′ JD 748G III Item ID: 3210
Contact: JOE
Email: Joe@lumbermensco.com Phone: 888-401-6367 EXT 709 (C) 801-362-2170
Contact: JOE
Phone: 888-401-6367 EXT 709 (C) 801-362-2170 TJ 460D Item ID: 3286
Contact: JOE
Email: Joe@lumbermensco.com
12' JD 550K LGP Item ID: 3753
Contact: JOE
Email: Joe@lumbermensco.com
Phone: 888-401-6367 EXT 709 (C) 801-362-2170
Phone: 888-401-6367 EXT 709 (C) 801-362-2170 06′ TIGERCAT 635C Item ID: 3322
Contact: AUSTIN
Email: Joe@lumbermensco.com
JOHN DEERE 848H Item ID: 2646
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
CAT 525D Item ID: 3172
Contact: JOE
Email: Joe@lumbermensco.com
Phone: 888-401-6367 EXT 709 (C) 801-362-2170
Phone: 888-401-6367 EXT 703 (C) 931-797-8029 04′ TIMBERJACK 460D Item ID: 2724
98′ JOHN DEERE 648 Item ID: 2798
Contact: AUSTIN
Email: Austin@lumbermensco.com
04′ JOHN DEERE 648G3 Item ID: 2791
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
F666 RANGER Item ID: 3233
Contact: JOE
Email: Joe@lumbermensco.com
Phone: 888-401-6367 EXT 709 (C) 801-362-2170
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
Contact: JOE
Email: Joe@lumbermensco.com
Phone: 888-401-6367 EXT 709 (C) 801-362-2170 02′ TJ 660D Item ID: 4088
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029 12′ TIGERCAT 620D Item ID: 2753
83′ TJ 380A Item ID: 2133
Contact: JOE
Email: Joe@lumbermensco.com
Phone: 888-401-6367 EXT 709 (C) 801-362-2170
13′ CAT 545C Item ID: 2117
Contact: JOE
Email: Joe@lumbermensco.com
Phone: 888-401-6367 EXT 709 (C) 801-362-2170
Contact: AUSTIN
Phone: 888-401-6367 EXT 703 (C) 931-797-8029 CAT 515 Item ID: 1739
Contact: JOE
Email: Austin@lumbermensco.com
‘83 John Deere 4850
05′ VALMET 415 EX TRACK
Item ID: 14073
FELLER BUNCHER Item ID: 8144
Contact: JOE
Email: Joe@lumbermensco.com
Contact: Austin Ph: (888) 401-6367 x703
Phone: 888-401-6367 EXT 709 (C) 801-362-2170
with 1700 hours, in very good condition. Easily produces high quality chips with patented ‘Cone’ drum design. Can easily load 42’ vans and produce 6 - 8 loads per day. Item ID 13882. Austin x703
Brewco Saws - Two Brewco Saws in excellent condition. Runs great. Item ID 13644. Sam x702
15′ CATERPILLAR 553C
FELLER BUNCHER
Item ID: 5495
FIREWOOD PROCESSORS
Item ID: Contact: Ph: ‘16
Halverson H140
Item ID: JW-909632
Contact: J Williams Ph: (888) 401-6367 x701
Contact: JOE
Phone: 888-401-6367 EXT 709 (C) 801-362-2170 08′ JD 535 SERIES II Item ID: 4580
10′ JOHN DEERE 648H Item ID: 1847
Contact: AUSTIN
Email: Joe@lumbermensco.com
Item ID: 14078
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
Phone: 888-401-6367 EXT 709 (C) 801-362-2170 17′ JD 437E Item ID: 4809
TIMBERJACK 240A GRAPPLE SKIDDER Item ID: 1769
Contact: Austin Ph: (888) 401-6367 x703
Contact: AUSTIN
Email: Joe@lumbermensco.com
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
off onto a conveyor. This is a very well built processor. Item ID 13820.
Sam x702
‘05 Gehl CTL 70
Contact: AUSTIN
chain conveyer, 8 way splitter, on 20,000lb goose neck trailer. Item ID 13916. Austin x703
Email: Austin@lumbermensco.com
Best Value Portable Log Splitter
Phone: 888-401-6367 EXT 703 (C) 931-797-8029 15′ TIGERCAT 724 G Item ID: 3392
-Small manufacturer in PA has made the best valued log splitter. Handles logs up to 32”. Uses 13HP Honda motor. Manual start but electronic option is available. Has Log Lift. Uses 4-way wedge adjustable to single two way. Great Value! PA. Item ID 12062. Sam x702
TIGERCAT 630E Item ID: 1098
Firewood Processor - This is a Chomper Model 16 PDA automatice firewood processor with John Deere power unit with low hours. Control panel includes tach, oil pressure, water temp and amp gauges. Cuts logs up to 16”. One owner and comes with all manuals and receipts. Purchased new for $32,500. Item ID 13865.
TIMBERJACK 460 Item ID: 1777
Contact: AUSTIN
Email: Austin@lumbermensco.com
Sam x702
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
LOGGING EQUIPMENT BANDIT
1999 Bandit 1900 Tracked Disc
Chipper - Cat Under Carriage at 50% or better. 475 hp Cummins Diesel. 7500 Hours. One owner. Well maintained. Item ID 13294.
Sam x702
2019 KOMATSU XT445 L-5 TRACK FELLER BUNCHER Item ID: 7243
capacity!. Item ID 13421. Sam
08′ JD 843J Item ID: 2109
Contact: JOE
Email: Joe@lumbermensco.com
Phone: 888-401-6367 EXT 709 (C) 801-362-2170
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029 17′ JOHN DEERE 843L Item ID: 2731
1994 Barko 160B - Electric knuckleboom, 30' boom, 75hp motor, Rotobec continuous grapple, 5,000 original hours. on injection pump. always started good. in good working order. 22in kohing head. head works great. Item ID 13185. Sam x702 1999 Barko 160D - new engine with approximately 1500 hours. Hour meter dont work. The last 2 owners have only used it to load trucks or as a backup as needed. Has a CTR delimber, grapple has been rebuilt. Boom cylinders have minor leaks.
Contact: JOE
2010 Shop Built Wood Processor
Email: Joe@lumbermensco.com
Contact: AUSTIN
Email: Austin@lumbermensco.com
Contact: AUSTIN
Phone: 888-401-6367 EXT 709 (C) 801-362-2170
-It has a 353 Detroit diesel, 40 inch insert tooth circle saw, 30 foot
Firewood Processor - This is a homemade processor with a 10’ log deck. Has a hydraulic grapple, chain and kicker that all runs off of a 4 cylinder Mercedes power unit. Has a 4’ chain saw that kicks
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
2004 Bandit Beast Model 46803412 Caterpillar Diesel engine with 850 HP. 5300 hrs. Mill in good condition. Just finished 10 Acre clearing job, ready to work! Remote control. Big production
Runs Great!. Item ID 13740. Sam x702
16′ COOKS AE4P EDGER Item ID: 5013
BELL
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
1990 Bell Super T - This Bell has a brand new Duetz engine. Lever control, 33” bar, pump and tranny
x702 BARKO
‘95 John Deere C6
PRENTICE
Item ID: 2166
Contact: JOE
Email: Joe@lumbermensco.com
Phone: 888-401-6367 EXT 709 (C) 801-362-2170
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
Contact: AUSTIN
Contact: JOE
Email: Joe@lumbermensco.com
Phone: 888-401-6367 EXT 709 (C) 801-362-2170 84' CAT 518 ROTOSAW CUTTER
Contact: JOE
Email: Joe@lumbermensco.com
Phone: 888-401-6367 EXT 709 (C) 801-362-2170
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
Contact: AUSTIN
Phone: 888-401-6367 EXT 703 (C) 931-797-8029 KOBELCO 250 LOG LOADER Item ID: 2584
Contact: JOE
Email: Austin@lumbermensco.com
Email: Joe@lumbermensco.com
Phone: 888-401-6367 EXT 709 (C) 801-362-2170
TIMBCO 415EX Item ID: 1661
Contact: AUSTIN
1/2" or 2"
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
Phone: 888-401-6367 EXT 703 (C) 931-797-8029 2014 PONSSE SCORPION KING Item ID: 4914
Contact: AUSTIN
Email: Austin@lumbermensco.com
ID: 741
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029 VALMET 644 Item ID: 1480
Contact: SAM
Email: Sam@lumbermensco.com
Phone: 888-401-6367 EXT 702 (C) 615-596-4148
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
3406 140KW Genset, 12,400 hours ready to run. Item ID 13434. Sam x702 CARRIAGES & DRIVES carriage turners, carriage drive, hyd pac for carriage, sawyers cab, computer controls, cabinet with electronic drives for carriage knees, husk including
Item ID: 1246
Contact: SAM
Email: Sam@lumbermensco.com
Phone: 888-401-6367 EXT 702 (C) 615-596-4148
JOHN DEERE 548G
SKIDDER Item ID: 8062
Contact: WALKER Email: Walker@lumbermensco.com Phone: 888-401-6367 EXT 707
‘16 Halverson H140
Item ID: JW-909632
Contact: J Williams Ph: (888) 401-6367 x701
Contact:
4850
Item ID: 14073
Contact: Austin Ph: (888) 401-6367 x703
with 1700 hours, in very good condition. Easily produces high quality chips with patented ‘Cone’ drum design. Can easily load 42’ vans and produce 6 - 8 loads per day. Item ID 13882. Austin x703 EDGERS & GANGS
chain conveyer, 8 way splitter, on 20,000lb goose neck trailer. Item ID 13916. Austin x703 Best Value Portable Log Splitter
amp gauges. Cuts logs up to 16”. One owner and comes with all manuals and receipts. Purchased new for $32,500. Item ID 13865. Sam x702
Brewco Saws - Two Brewco Saws in excellent condition. Runs great. Item ID 13644. Sam x702
FIREWOOD PROCESSORS
2010 Shop Built Wood Processor -It has a 353 Detroit diesel, 40 inch insert tooth circle saw, 30 foot
log deck. Has a hydraulic grapple, chain and kicker that all runs off of a 4 cylinder Mercedes power unit. Has a 4’ chain saw that kicks
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
Contact: AUSTIN
Email: Austin@lumbermensco.com
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
SIZER Item ID: 1322
Contact: SAM
Email: Sam@lumbermensco.com
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
Phone: 888-401-6367 EXT 703 (C) 931-797-8029 Contact: AUSTIN
931-797-8029
MORGAN MILITARY
BAND SAW Item ID: 3567
Contact: JOE
Email: Joe@lumbermensco.com
Phone: 888-401-6367 EXT 709 (C) 801-362-2170
Phone: 888-401-6367 EXT 702 (C) 615-596-4148
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
the bells and whistles, its a production machine, with air strain conveyers that go up and down, with airbags, it includes two sets of Mcdonough wheel sides. This machine 130 presses. S & W 125 Band Mill with Caterpillar generator - Low hours on the mill, electronic computer Set works,1 1/2" or 2" band, 22ft. track Cat 3406 140KW Genset, 12,400 hours ready to run. Item ID 13434. Sam x702 CARRIAGES & DRIVES carriage turners, carriage
Contact: AUSTIN
Email:
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
2021 WOODMIZER LT-70 SUPER WIDE Item ID: 7938
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
ID: 7710
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
‘16 Halverson H140 Skidsteer (DEMO)
Item ID: JW-909632
Contact: J Williams Ph: (888) 401-6367 x701
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
Contact: Austin Ph: (888) 401-6367 x703
Item ID: 7553
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
‘13 KMC 2500 Track Skidder
Item ID: 14078
SAWMILL Item ID: 7545
13428 Victory Ln. // PO Box 124 Adams Center, NY 13606
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
‘83 John Deere 4850
Item ID: 14073
Contact: Austin
Contact: SAM
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
‘05 Gehl CTL 70
Contact: Austin Ph: (888) 401-6367 x703
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
off onto a conveyor. This is a very well built processor. Item ID 13820.
Sam x702
Item ID: 5007
capacity!. Item ID 13421. Sam x702 BARKO
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
Item ID: Contact: Ph:
WITH HOOD LOADER Item ID: 1089
Ph: (888) 401-6367 x703
Email: Sam@lumbermensco.com
Phone: 888-401-6367 EXT 702 (C) 615-596-4148 CSI 4400 SLASHER Item ID: 6786
with 1700 hours, in very good condition. Easily produces high quality chips with patented ‘Cone’ drum design. Can easily load 42’ vans and produce 6 - 8 loads per day. Item ID 13882. Austin x703
Brewco Saws - Two Brewco Saws in excellent condition. Runs great. Item ID 13644. Sam x702 FIREWOOD PROCESSORS
NYLE FIREWOOD DRY KILN Item ID: 3588
chain conveyer, 8 way splitter, on 20,000lb goose neck trailer. Item ID 13916. Austin x703
Contact: SAM Email: Sam@lumbermensco.com Phone: 888-401-6367 EXT 702 (C) 615-596-4148
Firewood Processor - This is a Chomper Model 16 PDA automatice firewood processor with John Deere power unit with low hours. Control panel includes tach, oil pressure, water temp and amp gauges. Cuts logs up to 16”. One owner and comes with all manuals and receipts. Purchased new for $32,500. Item ID 13865.
Best Value Portable Log Splitter
-Small manufacturer in PA has made the best valued log splitter. Handles logs up to 32”. Uses 13HP Honda motor. Manual start but electronic option is available. Has Log Lift. Uses 4-way wedge adjustable to single two way. Great Value! PA. Item ID 12062. Sam x702
Sam x702
LOGGING EQUIPMENT BANDIT
1999 Bandit 1900 Tracked Disc
Chipper - Cat Under Carriage at 50% or better. 475 hp Cummins Diesel. 7500 Hours. One owner. Well maintained. Item ID 13294.
Sam x702
1994 Barko 160B - Electric knuckleboom, 30' boom, 75hp motor, Rotobec continuous grapple, 5,000 original hours. (excellent condition.). Item ID 13238. Chris x700 1995 Barko 775 B Feller Buncher -Pumps recently redone. 400 hrs on injection pump. always started good. in good working order. 22in kohing head. head works great. Item ID 13185. Sam x702
BLOCK SAW Item ID: 5342
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
2010 Shop Built Wood Processor
Contact: AUSTIN
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
-It has a 353 Detroit diesel, 40 inch insert tooth circle saw, 30 foot
Firewood Processor - This is a homemade processor with a 10’ log deck. Has a hydraulic grapple, chain and kicker that all runs off of a 4 cylinder Mercedes power unit. Has a 4’ chain saw that kicks
Contact: AUSTIN
Contact: AUSTIN Email: Austin@lumbermensco.com Phone: 888-401-6367 EXT 703 (C) 931-797-8029 WINCH FOR SALE Item ID: 5413 Contact: JOE Email: Joe@lumbermensco.com
Phone: 888-401-6367 EXT 709 (C) 801-362-2170
Email: Austin@lumbermensco.com
Phone: 888-401-6367 EXT 703 (C) 931-797-8029
2004 Bandit Beast Model 46803412 Caterpillar Diesel engine with 850 HP. 5300 hrs. Mill in good condition. Just finished 10 Acre clearing job, ready to work! Remote control. Big production
1999 Barko 160D - new engine with approximately 1500 hours. Hour meter dont work. The last 2 owners have only used it to load trucks or as a backup as needed. Has a CTR delimber, grapple has been rebuilt. Boom cylinders have minor leaks. Runs Great!. Item ID 13740. Sam x702
Item ID: 1051
Contact: AUSTIN
Email: Austin@lumbermensco.com
1990 Bell Super T - This Bell has a brand new Duetz engine. Lever control, 33” bar, pump and tranny
Phone: 888-401-6367 EXT 703 (C) 931-797-8029 LOG MAX 7000
with 1700 hours, in very good condition. Easily produces high quality chips with patented ‘Cone’ drum design. Can easily load 42’ vans and produce 6 - 8 loads per day. Item ID 13882. Austin x703
Brewco Saws - Two Brewco Saws in excellent condition. Runs great. Item ID 13644. Sam x702
2010 Shop Built Wood Processor
-It has a 353 Detroit diesel, 40 inch insert tooth circle saw, 30 foot
Value! PA. Item ID 12062.
AD DIRECTORY
‘16 Halverson H140 Skidsteer (DEMO)
Item ID: JW-909632
Contact: J Williams Ph: (888) 401-6367 x701
‘93
Barko 180B
Item ID: 14077
Contact: Austin Ph: (888) 401-6367 x703
‘13 KMC 2500 Track Skidder
Item ID: 14078
Contact: Austin Ph: (888) 401-6367 x703
off onto a conveyor. This is a very well built processor. Item ID 13820.
Sam x702
Firewood Processor - This is a Chomper Model 16 PDA automatice firewood processor with John Deere power unit with low hours. Control panel includes tach, oil pressure, water temp and amp gauges. Cuts logs up to 16”. One owner and comes with all manuals and receipts. Purchased new for $32,500. Item ID 13865.
Sam x702
LOGGING EQUIPMENT BANDIT
1999 Bandit 1900 Tracked Disc Chipper - Cat Under Carriage at 50% or better. 475 hp Cummins Diesel. 7500 Hours. One owner. Well maintained. Item ID 13294.
Sam x702
2004 Bandit Beast Model 46803412 Caterpillar Diesel engine with 850 HP. 5300 hrs. Mill in good condition. Just finished 10 Acre clearing job, ready to work! Remote control. Big production
‘95 John Deere C6 Tree Farmer
Item ID: 13920
Contact: Austin Ph: (888) 401-6367 x703
capacity!. Item ID 13421. Sam x702 BARKO
1994 Barko 160B - Electric knuckleboom, 30' boom, 75hp motor, Rotobec continuous grapple, 5,000 original hours. (excellent condition.). Item ID 13238. Chris x700
1995 Barko 775 B Feller Buncher -Pumps recently redone. 400 hrs on injection pump. always started good. in good working order. 22in kohing head. head works great. Item ID 13185. Sam x702
1999 Barko 160D - new engine with approximately 1500 hours. Hour meter dont work. The last 2 owners have only used it to load trucks or as a backup as needed. Has a CTR delimber, grapple has been rebuilt. Boom cylinders have minor leaks. Item ID 13694. Sam x702
94 Barko 275 - Excellent value with low at hours at 3,500. 5.9
CUMMINS continuous grapple. Runs Great!. Item ID 13740. Sam x702 BELL
1990 Bell Super T - This Bell has a brand new Duetz engine. Lever control, 33” bar, pump and tranny
20,000lb goose neck trailer. Item ID
Sam x702
