Stg cantilever gate specification

Page 1

Vehicle Access Solutions for Perimeter Protection

STG Heavy Duty Cantilever Gate The STG Cantilever Slide Gate is designed for heavy duty applications. This product eliminates the need for ground tracks and overhead rails.

Track

General

• • • • •

Gate leaf Main equipment tower and covers End post Back support rail All associated rollers, roller brackets and climb protection features.

Cantilever

Cantilever sliding gate system consist of the following metal work items:

The erected height of each gate system is 2150mm above ground (this is flexible and can be up to 3.0 metres). Ground clearance under the gate is 150mm. Climb protection (barbed wire, spikes, pressed spears, electrified wire) can be affixed to the top rail of the gate. Each gate system between the sizes of up to 7.9 metres opening have a gate frame of 89 x 89 x 4 SHS with a gate bottom member and cantilever support beam of 100 x 100 x 6 SHS. For gates between the sizes of 8.0 to 12.0 metres, 200 x 100 x 6 RHS are used for the bottom member and its cantilever support beam. This to give it more stability of larger opening distances. Vertical uprights are to be 25 x 25 x 2 SHS at 150mm centres. The main equipment tower will be made from 89 x 89 x 4 SHS and 1.6mm sheet metal cover-set. The width of each gate opening shall be determined on site and shall cover the entire road width.

Australian Content 100% Fully welded Australian made RHS steel is used in the gate frame, back runner and support posts, with 25 x 25mm RHS uprights. Gates are locally manufactured at our facility in Tullamarine, Melbourne, Victoria.

Management Systems Certifications and Risk Assessments Magnetic Automation is certified to the following Management Systems:

STG,001_EN_02/02.2015 | Subject to change without prior written notice. Page 1 of 3

• • •

Quality ISO9001:2008 Environment ISO14001:2004 Occupational Health and Safety OHSAS18001:2007

The STG Cantilever Slide Gate has been fully risk assessed by an external provider and this product complies with the Plant Regulations of 2007 and Australian Standards AS 4024 for Safe Guarding of Machinery and AS 4360 Risk Management Standards.

Slide Gate Drive System The STG slide gate has it’s own drive system with a fully programmable logic controller & 0.75kW German made heavy duty motor, necessary for the continuous use for speed and reliability. The fully programmable logic controller is selfcontained in its own secured IP65 rated enclosure and can be used in conjunction with any access security system. The motor and control unit are housed in a lockable gate tower which supports & secures the gate.

Safety Photo Electric Beams Each sliding gate, as a minimum, must have 2 photo electric safety beam sets fitted. All photo electric beams must be constantly monitored by the gate controller and positioned 600 mm and 1200 mm from road level. Should a beam be blocked by a person or vehicle, the system will stop and wait until cleared, prior to any further gate movement. All beams must be wired as safety stop. The motor and control unit are housed in a lockable gate tower which supports & secures the gate.

www.ac-magnetic.com/australia

Swing

All items are manufactured utilising heavy duty materials. All items are fully seam welded. All steel items are hot dip galvanized after manufacturing and cleaned as required to give a smooth even galvanized finish.


Safety Inductive Loop Detector and Loops Each sliding gate system must have at least 2 vehicle safety induction sensors in addition to the photo electric beam safety. One vehicle loop will be cut into the existing roadway 1.0 metre either side of the gate centre. All vehicle induction loops must be constantly monitored by the relevant gate controller. In the event that the safety loop is obstructed, the gate will immediately stop and either remain in this position until it is clear, or, retract back into the fully opened position. Technical Data Support Tower / Frame Load bearing plates Gate Frame Gate Frame Bottom Rail Infill uprights Gear drive rack Drive Cog Top Guide rollers Catch post / Docking Column Lower & support axles

2 x 65 x 65 x 12 Angle 89 x 89 x 4 SHS 100 x 100 x 6 SHS (Gates up to 7.9 metre gate) 200 x 100 x 6 RHS (Gates 8.0 to 12.0 metre) 25 x 25 x 2 SHS (150mm centres) M2.5 machined from 30mm x 30mm Solid Bright Steel 230mm Dia. Solid Bright Steel c/w 30mm Taper locking Bush 64 x 70 Machined Black Acetal (Cast Nylon) w/ 6004 bearings & S/Steel Shaft 100 x 100 x 4 SHS Machined 50mm Solid bright steel

Rear bottom support roller

100mm Solid w/ 4 80x50 6010 bearings

Rear top support roller

120mm solid w/ 4 80x50 6010 bearings

Front lower support roller

100mm solid w/ 4 80x50 6010 bearings

Finish

Technical Data Drive motor STG,001_EN_02/02.2015 | Subject to change without prior written notice. Page 2 of 3

Slide Gate and Support Gear 89 x 89 x 4 SHS, double A-frame style with lockabe sheet metal coverset to fully enclose the motor and controller enclosure

Motor Motor Duty Cycle Motor Output Power Gearbox Ratio Max. Torque Control Module Safety Devices Operating speed Power Failure

Hot Dip Galvanized after fabrication

Drive Mechanism SEW K47 DRE80 240v with 3 Phase output through inverter 100% 0.75 kW Helical / Bevel 41:1 184 Nm Programmable Logic Controller (PLC) Mitsubishi FX1s (14 I/O) Speed Inverter Mitsubishi FRD720S.75K-EC/Filter 2 x FAAC RX / TX Photocells 2 x FEIG MID 1E-800 Vehicle Induction Loop Detector Max. 800mm per second (recommended 500mm) Manual release key switch mounted on controller enclosure for motor brake release

www.ac-magnetic.com/australia


Technical Data

Type

STG Summary Data

Maximum Gate Opening Length

mm

12,000

Standard Gate Height (custom heights available)

mm

2,150

Drive Mechanism

SEW TM 3 phase

Opening & Closing speed

mm/sec

500

W

750

VAC

240

Duty Cycle

%

100

IP Protection - Controller

IP

IP65

IP Protection - Motor

IP

IP55

Motor Power Voltage

Warranty and Servicing 1 year warranty on all parts and labour. It is recommended that a Preventative Maintenance Program be adapted by the user to ensure consistent operational functioning of this Magnetic Product. Magnetic Automation offers a comprehensive Service and Preventative Maintenance Program for all it products.

STG,001_EN_02/02.2015 | Subject to change without prior written notice. Page 3 of 3

Diagram provided for information purposes only (based on typical 3 metre opening)

National Sales & Service 1300 364 864

Melbourne Head Office +61 3 9339 2900 info@magnetic-oz.com

Sydney +61 2 9421 8800 nswsales@magnetic-oz.com

Brisbane +61 7 3801 2100 qldsales@magnetic-oz.com

Perth +61 8 9205 9900 wasales@magnetic-oz.com

www.ac-magnetic.com/australia


Turn static files into dynamic content formats.

Create a flipbook
Issuu converts static files into: digital portfolios, online yearbooks, online catalogs, digital photo albums and more. Sign up and create your flipbook.