Contents Introduction 3 Product Overview
4
Wall, Floor & Ceiling Fixtures
6
Cabinet Fixtures
82
Canopy Mount & Rail Systems
102
Picture Lights
116
Pendants 122 Linear Systems
136
Desk & Table Fixtures
156
Hardware 160 Accessories 175 Drivers 176 Driver Enclosures
183
Magnetic Low Voltage Transformers
184
Recommended Driver Chart
186
Lamp Index & Isofootcandle Calculation
191
Explanation of Symbols
192
Mounting & Finishing Options
193
Online with MP Lighting
194
Research & Development
195
Terms & Warranty
196
Index 197
Introduction
www.mplighting.com
The realities of LED lighting are clear—with an average product life of 50,000 hours, LEDs are the most energy efficient and cost effective lighting option on the market. They contain no mercury or moving parts that could break, leak or shatter, limiting their impact on the environment. The right LED lighting can instantly enhance any space, while allowing users to conserve energy and save money. At MP Lighting, we are committed to providing you with the most current information and technology related to solid-state lighting. Our LEDs are produced using quality materials and are tested to ensure reliability and performance. We use high output lamps which are 10 to 20 times brighter than standard LEDs to ensure optimal light output and efficacy is achieved in each application. Our LED thermal management system ensures an efficient performance and utmost product life. Our commitment to quality products extends beyond their construction. When our LED products can no longer be used, all product parts are recyclable. The end result of our commitment is a clean, clear, and energy-efficient light guaranteed to complement any design. 2 3
Product Overview
Wall, Floor & Ceiling Fixtures
L01 (p.6-7)
L02 (p.8-9)
L03 (p.10-11)
L04 (p.12-13)
L05 (p.14-15)
L06 (p.16-17)
L07 (p.18-19)
L11 (p.20-21)
L12 (p.22-23)
L13 (p.24-25)
L14 (p.26-27)
L15 (p.28-29)
L16 (p.30-31)
L17 (p.32-33)
L18 (p.34-35)
L19 (p.36-37)
L21 (p.38-39)
L22 (p.40-41)
L31 (p.42-43)
L32 (p.44-45)
L33 (p.46-47)
L34 (p.48-49)
L35 (p.50-51)
L36 (p.52-53)
L37 (p.54-55)
L91 (p.56-57)
L92 (p.58-59)
L97 (p.60-61)
L98 (p.62-63)
L99 (p.64-65)
L130 (p.66-67)
L131 (p.68-69)
L134 (p.70-71)
L135 (p.72-73)
L141 (p.74-75)
L142 (p.76-77)
L151 (p.78-79)
L181 (p.80-81)
L55, 3 x 1W
L56, 3 x 1W
L57, 3 x 1W
L58, 2.5W
L59, 3.7W
L62, 3.2W
Cabinet Fixtures
L51, 1W / 2.5W
L52, 1W / 2.5W
L64, 2.5W
L65, 2.5W (p.100-101)
(p.82-83)
(p.98-99)
(p.84-85)
(p.86-87)
(p.88-89)
(p.90-91)
(p.92-93)
(p.94-95)
(p.96-97)
Canopy Mount & Rail Systems
L72 (p.102-103) L73 (p.104-105) L75 (p.106-107) L76 (p.108-109) L221 (p.110-111) L222 (p.112-113) L223 (p.114-115)
Picture Lights
L81 (p.116-117)
L85 (p.118-119)
Product Overview
www.mplighting.com
L202 (p.120-121)
Pendants
L96 (p.122-123)
L191 (p.124-125) G02L (p.126-127) G03L (p.128-129) P71L (p.130-131) P81L (p.132-133) P82L (p.134-135)
Linear Systems
L101, 1W
(p.136-137)
L102, 0.07W (p.138-139)
L112, 2.5W (p.148-149)
L103, 1W
(p.140-141)
L121, 0.07W (p.150-151)
L104, 1W
(p.142-143)
L106, 1W
(p.144-145)
L161, 1W
(p.152-153)
L111, 1W
(p.146-147)
L171, 1W
(p.154-155)
Desk & Table Fixtures
L200 (p.156-157) L203 (p.158-159) 4 5
Image shows L01-1W30SNC30-S2MA
L01
www.mplighting.com
Wall, Floor & Ceiling Fixtures
L01 1W / 2.5W In-ground Application Outdoor / indoor directional ingrade light for uplighting walls, columns, or architectural features. Source 1W, 350mA or 2.5W, 700mA LED Driver Remote 120V primary, 350mA (1W) or 700mA (2.5W) driver (not included). LED Input Voltage 4V DC Power Consumption 1.5W / 3W Dimming 0~10V dimming with remote dimmable driver (not included). See page 186190 for Recommended Driver Chart. Weight 1.8lbs net. (0.816kg) (base extra). Material Solid anodized aluminum or stainless steel with 1/4” (6mm) thick tempered glass lens, suitable for walk-over and drive-over applications. RoHS compliant.
Ø4-1/8” Ø105mm
Mounting Comes with splice box, aluminum flange and level gauge. Can be buried in earth/gravel or cast into concrete/paving stone with or without mounting base.
Ø2-1/4” Ø57mm
Approval Wet and dry locations. Approved to US and Canadian standards by CSA. Note Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
66
Polar Candela Distribution
4-7/8” 124mm
Base Height
Illuminance at a Distance
Center Beam FC
45°
approx. 700 cd max.
-90°
90°
L01 2.5W, 12° Clear lens 3000K Std 89 lm
8.44
2.2’
2.3’
7.5’
12.15
1.9’
2.0’
6.0’
18.99
1.5’
1.6’
4.5’
33.76
1.1’
1.2’
3.0’
75.95
0.7’
0.8’
1.5’
303.82
0.4’
0.4’
Polar Candela Distribution
90° Spread: 14.9°
Illuminance at a Distance
Splice box with 1/2 NPT I/O ports for connector and wiring.
Shown with standard flange (S) and (optional) mounting base.
Beam Width
9.0’
0° Spread: 14.1°
0°
paving stone
Paving stone flange 3-5/8” (92mm)
sand
180°
Center Beam FC
-45°
Lumen test results provided by MP Lighting integrating sphere (see page 194).
45°
approx. 1300 cd max.
-90°
90°
Wattage
Color
Beam Width
9.0’
16.08
2.2’
2.3’
7.5’
23.16
1.9’
2.0’
6.0’
36.19
1.5’
1.6’
4.5’
64.34
1.1’
1.2’
3.0’
144.76
0.7’
0.8’
1.5’
579.04
0.4’
0.4’
0° Spread: 14.1°
0°
Code L01
Standard flange 7/8” (22mm)
180°
-45°
Concrete pouring line
2-3/4” 70mm
See page 192 for explanation of symbols and IP ratings.
L01 1W, 12° Clear lens 3000K Std 53 lm
1/8” 3mm
Ø1-5/8” Ø41mm
Beam
Shown with paving stone flange (P) with no base.
90° Spread: 14.9°
Lens
Option**
Angle Bracket
-
Flange Height
Base Height
Finish
S = standard flange 5/8” (17mm) P = paving stone flange, 3-3/8” (86mm)
0 = no base 2 = 2” (51mm) 6 = 6” (152mm)
MA = matte clear anodized BA = black anodized BZ = bronze S3 = stainless steel 303 S6 = stainless steel 316
1 = 1W W27S = 2700K, 2 = 2.5W* std CRI W30S = 3000K, std CRI W35S = 3500K, std CRI W41S = 4100K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
S = spot (12°) N = narrow flood (30°) W = wide flood (120°)
C = clear F = frosted
LM = louver, matte anodized LB = louver, black anodized
0 = no angle 30 = 30° angle X = custom (30° max.)
**Louver not available with angle bracket. NOTE: Standard CRI has a value of 75~82 while high CRI has 92. *Only available in W30S & W20H.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
6 7
Image shows L02-1W30SNC30-MA
L02
www.mplighting.com
Wall, Floor & Ceiling Fixtures
L02 1W / 2.5W Walkway Application Indoor wall mounted directional or indicator light for stair, ramp, and aisle illumination. Source 1W, 350mA or 2.5W, 700mA LED Driver Remote 120V primary, 350mA (1W) or 700mA (2.5W) driver (not included). LED Input Voltage 4V DC Power Consumption 1.5W / 3W Dimming 0~10V dimming with remote dimmable driver (not included). See page 186190 for Recommended Driver Chart. Weight 0.35lbs (0.158kg). Material Solid anodized aluminum or stainless steel with 1/4” (6mm) thick tempered glass lens. RoHS compliant.
1” 25mm
3-1/2” 89mm
1/8” (3mm) Face of drywall
Mounting Comes with steel flange which mounts to pre-installed standard 4” (102mm) octagonal box, 1-1/2” (38mm) deep minimum and 1/4” (6mm) setback from face of drywall. Can be wall or ceiling mounted.
Angle Ø2-1/4” Ø57mm
Approval Dry locations. Approved to US and Canadian standards by CSA. Note Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
Ø1-3/4” Ø44mm
Ø4-1/8” Ø105mm
1-3/4” 44mm
1-3/4” 44mm
53 See page 192 for explanation of symbols and IP ratings.
L02 1W, 30° Clear lens 3000K Std 51 lm
Polar Candela Distribution
Isofootcandle Plot
135°
180°
2 4
6 8 10 12 14 16 18
8 6 4 -90°
2 0 2 4 6
90°
-0°
approx. 260 cd max. 0°
L02 2.5W, 30° Clear lens 3000K Std 84 lm
8
-90°
Mount height: 1 ft Total LLF: 1
45°
Polar Candela Distribution 180°
1 0.5 0.2 0.1 fc
Isofootcandle Plot
135°
0
4
8
12
16
20
24
8 4
Lumen test results provided by MP Lighting integrating sphere (see page 194).
-90°
2.5
0
0.5 0.2 0.1 fc
4
-0°
approx. 480 cd max. 0°
Code L02
90°
8
-90°
10
Mount height: 1 ft Total LLF: 1
45°
Wattage
Color
Beam
Lens
Option**
Angle Bracket
-
Finish -
1 = 1W 2 = 2.5W*
W27S = 2700K, std CRI W30S = 3000K, std CRI W35S = 3500K, std CRI W41S = 4100K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
S = spot (12°) N = narrow flood (30°) W = wide flood (120°)
C = clear F = frosted
LM = louver, matte anodized LB = louver, black anodized
0 = no angle 30 = 30° angle 45 = 45° angle X = custom (45° max.)
MA = matte clear anodized BA = black anodized S3 = stainless steel 303 S6 = stainless steel 316
**Max. 30° angle bracket with louver opion.
*Only available in W30S & W20H. NOTE: Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
8 9
Image shows L03-1W30SNC0-B6MA
L03
www.mplighting.com
Wall, Floor & Ceiling Fixtures
L03 1W / 2.5W Submersible Application Submersed fresh water illumination to 12” (305mm) depth. Perfect for core drilling retrofits without back box and flange. Source 1W, 350mA or 2.5W, 700mA LED Driver Remote 120V primary, 350mA (1W) or 700mA (2.5W) driver (not included). LED Input Voltage 4V DC 4-3/8” 111mm
Power Consumption 1.5W / 3W Dimming 0~10V dimming with remote dimmable driver (not included). See page 186-190 for Recommended Driver Chart. Weight 2.45lbs (1.11kg)
Buna rubber gasket sealing, tight to keep Ø1-5/8” in position even when upside down. Ø41mm Angle
Ø4-1/8” Ø105mm
Material Solid anodized aluminum or stainless steel with 1/4” (6mm) thick tempered glass lens and 6’ (1829mm) Captire lead. RoHS compliant.
Mounting box with 1/2 NPT I/O ports for connector and wiring.
Mounting Comes with mounting box, aluminum flange and level gauge. Can be buried in earth/gravel or cast into concrete for submersed applications.
Shown4-3/8” with mounting box 111mm 3” 76mm
Approval Submersible. Approved to US and Canadian standards by CSA.
1/8” Mounting box 3mm with 1/2 NPT Concrete pouring line I/O ports for
Note Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
3-1/2” 89mm
connector and Ø2-1/4” wiring. Ø57mm
68
1-1/8” 29mm
See page 192 for explanation of symbols and IP ratings.
Shown with flange only
L03 1W, 120° Clear lens 3000K Std 50 lm
Polar Candela Distribution 180°
Isofootcandle Plot
135°
1 2 3 4 5 6 7 8 9 8 6 4
-90°
2 0 2 4 6
90°
-0°
approx. 28 cd max. 0°
L03 2.5W, 120° Clear lens 3000K Std 81 lm
Mount height: 1 ft Total LLF: 1
Polar Candela Distribution
Isofootcandle Plot
135°
1 2 3 4 5 6 7 8 9 8 6 4
Lumen test results provided by MP Lighting integrating sphere (see page 194).
-90°
2 0 2 4 6
90°
-0°
approx. 55 cd max. 0°
Code L03
8
-90°
45°
180°
2.5 0.5 0.2 0.1 fc
1
0.2 0.1 fc
8
-90°
Mount height: 1 ft Total LLF: 1
45°
Wattage
10
Color
Beam
Lens
Option**
Angle Bracket
-
Mounting
Lead Length
Finish
B = mounting box F = flange only
6 = 6’ (1829mm) X = custom
MA = matte clear anodized BA = black anodized S3 = stainless steel 303 S6 = stainless steel 316
1 = 1W 2 = 2.5W*
W27S = 2700K, std CRI W30S = 3000K, std CRI W35S = 3500K, std CRI W41S = 4100K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
S = spot (12°) N = narrow flood (30°) W = wide flood (120°)
C = clear F = frosted
LM = louver, matte anodized LB = louver, black anodized
0 = no angle 30 = 30° angle X = custom (30° max.)
**Louver not available with angle bracket.
*Only available in W30S & W20H. NOTE: Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
10 11
Image shows L04-1W30SNC30-S2MA
L04
www.mplighting.com
Wall, Floor & Ceiling Fixtures
L04 1W / 2.5W In-ground Application Outdoor / indoor directional ingrade light for uplighting walls, columns, or architectural features. Source 1W, 350mA or 2.5W, 700mA LED Driver Remote 120V primary, 350mA (1W) or 700mA (2.5W) driver (not included). LED Input Voltage 4V DC Power Consumption 1.5W / 3W Dimming 0~10V dimming with remote dimmable driver (not included). See page 186190 for Recommended Driver Chart. Weight 1.83lbs net. (0.83kg) (base extra) Material Solid anodized aluminum or stainless steel with 1/4” (6mm) thick tempered glass lens, suitable for walk-over and drive-over applications. RoHS compliant.
Ø4-1/8” Ø105mm
Mounting Comes with splice box, aluminum flange and level gauge. Can be buried in earth/gravel or cast into concrete/paving stone with or without mounting base.
Sq.2-1/4” Sq.57mm
Approval Wet and dry locations. Approved to US and Canadian standards by CSA. Note Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
2-3/4” 70mm
66
Polar Candela Distribution
Center Beam FC
-45°
45°
approx. 700 cd max.
-90°
90°
8.44
2.2’
2.3’
7.5’
12.15
1.9’
2.0’
6.0’
18.99
1.5’
1.6’
4.5’
33.76
1.1’
1.2’
3.0’
75.95
0.7’
0.8’
1.5’
303.82
0.4’
0.4’
0° Spread: 14.1°
Polar Candela Distribution
paving stone
90° Spread: 14.9°
Illuminance at a Distance
Paving stone flange 3-5/8” (92mm)
sand
180°
Center Beam FC
-45°
Lumen test results provided by MP Lighting integrating sphere (see page 194).
45°
approx. 1300 cd max.
-90°
90°
Wattage
Beam Width
9.0’
16.08
2.2’
2.3’
7.5’
23.16
1.9’
2.0’
6.0’
36.19
1.5’
1.6’
4.5’
64.34
1.1’
1.2’
3.0’
144.76
0.7’
0.8’
1.5’
579.04
0.4’
0.4’
0° Spread: 14.1°
0°
Code L04
Splice box with 1/2 NPT I/O ports for connector and wiring.
Shown with standard flange (S) and (optional) mounting base.
Beam Width
9.0’
0°
L04 2.5W, 12° Clear lens 3000K Std 89 lm
Base Height
Illuminance at a Distance
180°
Concrete pouring line
Standard flange 7/8” (22mm)
4-7/8” 124mm
See page 192 for explanation of symbols and IP ratings.
L04 1W, 12° Clear lens 3000K Std 53 lm
1/8” 3mm
Ø1-5/8” Ø41mm
Color
Beam
Shown with paving stone flange (P) with no base.
90° Spread: 14.9°
Lens
Option**
Angle Bracket
-
Flange Height
Base Height
Finish
S = standard flange 5/8” (17mm) P = paving stone flange, 3-3/8” (86mm)
0 = no base 2 = 2” (51mm) 6 = 6” (152mm)
MA = matte clear anodized BA = black anodized S6 = stainless steel 316
1 = 1W 2 = 2.5W*
W27S = 2700K, std CRI W30S = 3000K, std CRI W35S = 3500K, std CRI W41S = 4100K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
S = spot (12°) C = clear N = narrow flood F = frosted (30°) W = wide flood (120°)
LM = louver, matte anodized LB = louver, black anodized
0 = no angle 30 = 30° angle X = custom (30° max.)
**Louver not available with angle bracket.
*Only available in W30S & W20H. NOTE: Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
12 13
Image shows L05-3W30SFC0-2MA
L05
www.mplighting.com
Wall, Floor & Ceiling Fixtures
L05 3W / 7.5W In-ground Application Outdoor / indoor directional ingrade light for uplighting walls, columns, or architectural features. Source 3 x 1W, 350mA or 3 x 2.5W, 700mA LEDs Driver Remote 120V primary, 350mA (3W) or 700mA (7.5W) driver, or 12V constant voltage driver (not included). LED Input Voltage 12V DC Power Consumption 4W / 9W Dimming 0~10V dimming with remote dimmable driver (not included). See page 186190 for Recommended Driver Chart.
Ø4-5/8” Ø117mm
Weight 2.56lbs (1.16kg) (base extra). Material Solid anodized aluminum or stainless steel with 3/8” (10mm) thick tempered glass lens, suitable for walk-over and drive-over applications. RoHS compliant.
Ø2-11/16” Ø69mm 3-1/8” 79mm
Mounting Comes with splice box, aluminum flange and level gauge. Can be buried in earth/gravel or cast into concrete with or without mounting base. Approval Wet and dry locations. Approved to US and Canadian standards by CSA. Note Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
Ø3-5/8” Ø92mm
Concrete pouring line
2-1/2” 4-1/2” 65mm 114mm
1/4” 6mm
4-7/8” 124mm
66
Base Height
See page 192 for explanation of symbols and IP ratings.
L05 3 x 1W 30° 3000K Std 177 lm
Polar Candela Distribution
Illuminance at a Distance
Shown with (optional) mounting base.
180°
Center Beam FC
-45°
45°
approx. 650 cd max.
-90°
90°
L05 3 x 2.5W 30° 3000K Std 270 lm
Polar Candela Distribution
4.8’
4.9’
7.5’
11.79
4.0’
4.0’
6.0’
18.42
3.2’
3.2’
4.5’
32.75
2.4’
2.4’
3.0’
73.68
1.6’
1.6’
1.5’
294.71
0.8’
0.8’
90° Spread: 30.2°
Illuminance at a Distance
180°
Center Beam FC
-45°
Lumen test results provided by MP Lighting integrating sphere (see page 194).
45°
approx. 1300 cd max.
-90°
90°
Wattage
Beam Width
9.0’
15.60
4.8’
4.9’
7.5’
22.47
4.0’
4.0’
6.0’
35.10
3.2’
3.2’
4.5’
62.41
2.4’
2.4’
3.0’
140.42
1.6’
1.6’
1.5’
561.68
0.8’
0.8’
0° Spread: 29.9°
0°
Code L05
8.19
0° Spread: 29.9°
0°
Beam Width
9.0’
Color
Beam
90° Spread: 30.2°
Lens
Angle Bracket
-
Base Height
Finish
0 = no height 2 = 2” (51mm) high 6 = 6” (152mm) high
MA = matte clear anodized BA = black anodized S6 = stainless steel 316
3 = 3 x 1W 7 = 3 x 2.5W*
W27S = 2700K, std CRI W30S = 3000K, std CRI W35S = 3500K, std CRI W41S = 4100K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
N = narrow flood (30°) F = flood (60°)
C = clear F = frosted
0 = no angle 30 = 30° angle
*Only available in W30S & W20H. NOTE: Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
14 15
Image shows L06-W27SB4-S6
L06
www.mplighting.com
Wall, Floor & Ceiling Fixtures
L06 0.1W In-ground Application Outdoor / indoor indicator light for driveway and sidewalk. Source 0.1W, 20mA LED Driver Remote 120V primary, 6V constant voltage, 20mA driver (not included). LED Input Voltage 6V DC Power Consumption 0.1W Weight 1.21lbs (0.549kg). Material Stainless steel 316. RoHS compliant. Mounting Can be buried in earth/gravel or cast into concrete with or without mounting base. Ø7/8” Ø22mm
Approval Wet and dry locations. Approved to US and Canadian standards by CSA.
3/8 IPS Nipple Ø7/8” Ø22mm
67
Nipple
3/8 IPS Nipple
See page 192 for explanation of symbols and IP ratings.
Nipple 2-3/8” 60mm
Shown with no base (to 1/2 NPT connector)
2-3/8” 60mm
4-7/8” 124mm
Shown with base 4-7/8” 124mm Ø3/4” Ø19mm
L06 2700K Std 3.2 lm
Polar Candela Distribution
Illuminance at a Distance
Ø3/4” Concrete Ø19mm pouring line
180°
Center Beam FC
-45°
Lumen test results provided by LED chip manufacturer.
45°
approx. 3.3 cd max.
-90°
90°
Beam Width
1.0’
3.31
0.4’
0.4’
0.8’
4.77
0.3’
0.3’
0.7’
7.45
0.3’
0.3’
0.5’
13.25
0.2’
0.2’
0.3’
29.80
0.1’
0.1’
0.2’
119.21
0.1’
0.1’
0° Spread: 23.4°
0°
Concrete pouring line
90° Spread: 23.2°
Ø4-1/2” Ø114mm Ø4-1/2” Ø114mm
Code L06
Color -
Base
Nipple
W27S W27S = 2700K, std CRI
Finish -
B = with base N = no base
2 = 2” (51mm) long 4 = 4” (102mm) long 8 = 8” (203mm) long X = custom length
S6 S6 = stainless steel 316
NOTE: Standard CRI has a value of 75~82.
16 17
Image shows L07-W27S-S6
L07
www.mplighting.com
Wall, Floor & Ceiling Fixtures
L07 0.1W In-floor Application Outdoor / indoor indicator light for deck flooring. Source 0.1W, 20mA LED Driver Remote 120V primary, 6V constant voltage, 20mA (not included). LED Input Voltage 6V DC Power Consumption 0.1W
Ø3/8” Ø8mm
Weight 0.05lbs (0.024kg).
Ø3/4” Ø19mm
Material Stainless steel 316. RoHS compliant. Mounting Mounts directly into deck flooring.
1/8” 3mm
Approval Wet and dry locations. Approved to US and Canadian standards by CSA.
Ø1/2” Ø13mm
1-1/2” 38mm
67 See page 192 for explanation of symbols and IP ratings.
L07 2700K Std 3.2 lm
Polar Candela Distribution
Illuminance at a Distance
180°
Center Beam FC
-45°
Lumen test results provided by LED chip manufacturer.
45°
approx. 3.3 cd max.
-90°
90°
Code L07
Color -
W27S W27S = 2700K, std CRI
3.31
0.4’
0.4’
0.8’
4.77
0.3’
0.3’
0.7’
7.45
0.3’
0.3’
0.5’
13.25
0.2’
0.2’
0.3’
29.80
0.1’
0.1’
0.2’
119.21
0.1’
0.1’
0° Spread: 23.4°
0°
Beam Width
1.0’
90° Spread: 23.2°
Finish -
S6 S6 = stainless steel 316
NOTE: Standard CRI has a value of 75~82 while high CRI has 92.
18 19
Image shows L11-1W30SWV-MC
L11
www.mplighting.com
Application Indoor stair, ramp, aisle, and walkway illumination.
1-1/2” 38mm
Source 1W, 350mA or 2.5W, 700mA LED Driver Integral 120V primary, 3W 350mA (1W) or 9W 700mA (2.5W) non-dimmable driver.
3-1/8” 79mm
7/8” 22mm
4-3/4” 121mm
3-1/4” 83mm
Power Consumption 1.5W / 3W Dimming 0~10V dimming with remote dimmable driver (not included). See page 186190 for Recommended Driver Chart.
1-3/8” 35mm
Ø1-1/2” Ø38mm
Weight 0.59lbs (0.266kg). 3-1/8” Material Plated1-1/2” brass, anodized aluminum. RoHS compliant. 38mm
7/8” horizontally 22mmpositioned
79mm
1-1/2” 38mm gang box
Mounting Vertically or face plate mounts to single included). Optimal mounting distance is 18” - 24” (457mm - 610mm) AFF.
(not
7/8” 22mm
4-3/4” 121mm
3-1/4” 83mm
3-1/4” Approval Dry locations. Approved to US and Canadian standards by CSA. 83mm
4-3/4” 121mm
5/8” 16mm
Note Can be used as emergency backup lighting in conjunction with Bodine emergency 1-3/8” Ø1-1/2” LED driver (sold 35mmseparately). Consult factory. 1-3/8” Ø38mm
Shown as 120° beam Vertical plate
Shown as 120° beam 3-1/8” Horizontal plate 79mm
Wall, Floor & Ceiling Fixtures
Shown as 12° or 30° beam Vertical plate
L11 1W / 2.5W Walkway
5/8” 16mm Ø1-1/2” Ø38mm
35mm
50 See page 192 for explanation of symbols and IP ratings.
L11 1W, 12° 3000K Std 85 lm
Polar Candela Distribution
Isofootcandle Plot
180°
2
-90°
90°
1
0
2
approx. 750 cd max.
45°
3
-0°
4
-90°
5
Polar Candela Distribution
2
-90°
90°
0
-45°
approx. 1500 cd max.
45°
0
2
0.5
3
0.1 fc
-0°
4
-90°
5
1
2
3
Mount height: 1 ft Total LLF: 1
0°
L11
1
20 5
1
Code
3
Isofootcandle Plot
180°
Lumen test results provided by LED chip manufacturer.
2
Mount height: 1 ft Total LLF: 1
0°
L11 2.5W, 12° 3000K Std 162 lm
1
20 1.0 0.2 0.1 fc
1
-45°
0
Wattage
Color
Beam
Plate
-
Finish -
1 = 1W 2 = 2.5W*
W27S = 2700K, std CRI W30S = 3000K, std CRI W35S = 3500K, std CRI W41S = 4100K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
S = spot (12°) N = narrow flood (30°) W = wide flood (120°)
V = vertical H = horizontal
MC = matte chrome BK = powder coated black BN = brushed nickel
*Only available in W30S & W20H. NOTE: Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
20 21
5/8” 16mm
Image shows L12-1W30SSW30SS-MC
L12
www.mplighting.com
1-3/8” 35mm
Application Indoor stair, ramp, aisle, and walkway illumination.
1-1/2” 38mm
3-1/8” 79mm
Source 2 x 1W, 350mA or 2 x 2.5W, 700mA LEDs. 4-3/4” 121mm
3-1/4” 83mm
Driver Integral 120V primary, 3W 350mA (2W) or 9W 700mA (5W) non-dimmable driver. Power Consumption 3W / 6W
7/8” 2-1/8” 22mm 54mm
Dimming 0~10V dimming with remote dimmable driver (not included). See page 186190 for Recommended Driver Chart.
Ø1-1/2” Ø38mm
Weight 0.914lbs (0.415kg). Material Plated brass, anodized aluminum. RoHS compliant. Mounting Vertically positioned face
1-3/8” 1-3/8” 35mm 35mm plate mounts
to a single
Shown as 120° beam 1-1/2” 1-1/2” 38mm 38mm gang box (not
Wall, Floor & Ceiling Fixtures
Shown as 12° or 30° beam
L12 2 x 1W / 2.5W Up and Down Walkway
3-1/8” 3-1/8” 79mm 79mm included).
Approval Dry locations. Approved to US and Canadian standards by CSA. 4-3/4” 4-3/4” 121mm 121mm
3-1/4” 3-1/4”
83mm in conjunction with Bodine emergency Note Can be used as emergency backup83mm lighting LED driver (sold separately). Consult factory. 7/8” 7/8” 2-1/8” 2-1/8” 22mm 22mm 54mm 54mm
1-5/8” 1-5/8” 41mm 41mm
Ø1-1/2” Ø1-1/2” Ø38mm Ø38mm
50 See page 192 for explanation of symbols and IP ratings.
L12 2 x 1W, 30° 3000K Std 170 lm
Polar Candela Distribution
Isofootcandle Plot
180°
2
-90°
90°
1
0
2
approx. 300 cd max.
45°
3
-0°
4
-90°
5
Polar Candela Distribution
2
-90°
90°
1
0
-45°
approx. 550 cd max.
45°
2 3
0.1 fc
-0°
4
-90°
5
1
2
3
Mount height: 1 ft Total LLF: 1
0°
L12
0
20 2.5 0.5
1
Code
3
Isofootcandle Plot
180°
Lumen test results provided by LED chip manufacturer.
2
Mount height: 1 ft Total LLF: 1
0°
L12 2 x 2.5W, 30° 3000K Std 324 lm
1
20 1.0 0.2 0.1 fc
1
-45°
0
Wattage
Color UP
Beam UP
Color Down
Beam Down
-
Finish -
1 = 1W 2 = 2.5W*
W27S = 2700K, std CRI W30S = 3000K, std CRI W35S = 3500K, std CRI W41S = 4100K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
S = spot (12°) N = narrow flood (30°) W = wide flood (120°)
W27S = 2700K, std CRI W30S = 3000K, std CRI W35S = 3500K, std CRI W41S = 4100K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
S = spot (12°) N = narrow flood (30°) W = wide flood (120°)
MC = matte chrome BK = powder coated black BN = brushed nickel
*Only available in W30S & W20H. NOTE: Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
22 23
1-5/ 41m
Image shows L13-1W30SWV-MC
L13
www.mplighting.com
Application Indoor stair, ramp, aisle, and walkway illumination. Source 1W, 350mA or 2.5W, 700mA LED Driver Integral 120V primary, 3W 350mA (1W) or 9W 700mA (2.5W) non-dimmable driver. Power Consumption 1.5W / 3W Dimming 0~10V dimming with remote dimmable driver (not included). See page 186190 for Recommended Driver Chart. Weight 0.78lbs (0.353kg). Material Plated brass, anodized aluminum. RoHS compliant.
Shown as 12° or 30° beam Vertical plate
Mounting Vertically or horizontally positioned face plate mounts to single gang box (not included). Optimal mounting distance is 18” - 24” (457mm - 610mm) AFF.
1-1/4” 32mm
Wall, Floor & Ceiling Fixtures
L13 1W / 2.5W Walkway
3-1/8” 79mm
Approval Dry locations. Approved to US and Canadian standards by CSA. Note Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
1-3/4” 44mm
3-1/4” 83mm
1-3/8” 35mm
50
1-1/2” 38mm
4-3/4” 121mm
Ø1-1/2” Ø38mm
See page 192 for explanation of symbols and IP ratings.
L13 1W, 12° 3000K Std 85 lm
1-1/4”
3-1/8” 79mm
32mm Polar Candela Distribution
32mm
180°
2
-90° 3-1/4” 83mm
1-3/4” 44mm
4-3/4” 0 121mm
90°
1
45°
750 cd max.
-0°
Ø1-1/2” 3 Ø38mm
-90°
1-3/8” 35mm
Ø1-1/2” Ø38mm
Isofootcandle Plot 2
-90°
90°
0
-45°
approx. 1500 cd max.
45°
1
0
2
0.5
3
0.1 fc
-0°
4
-90°
5
1
2
3
20 5
1
Mount height: 1 ft Total LLF: 1
0°
L13
1-1/2” 38mm
Mount height: 1 ft Total LLF: 1
180°
Code
4-3/4” 121mm
5
Polar Candela Distribution
Lumen test results provided by LED chip manufacturer.
3
1-1/2” 38mm 1-3/4” 44mm
4
0°
L13 2.5W, 12° 3000K Std 162 lm
2
0.2 0.1 fc
2
1-3/8” 35mm approx.
1
3-1/4” 20 83mm1.0
1
-45°
0
Shown as 120° beam Vertical plate
Shown as 120° beam 3-1/8” Horizontal plate 79mm
1-1/4” Isofootcandle Plot
Wattage
Color
Beam
Plate
-
Finish -
1 = 1W 2 = 2.5W*
W27S = 2700K, std CRI W30S = 3000K, std CRI W35S = 3500K, std CRI W41S = 4100K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
S = spot (12°) N = narrow flood (30°) W = wide flood (120°)
V = vertical H = horizontal
MC = matte chrome BK = powder coated black BN = brushed nickel
*Only available in W30S & W20H. NOTE: Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
24 25
Image shows L14-1W30SWV-MC
L14
www.mplighting.com
Application Indoor stair, ramp, aisle, and walkway illumination.
1-1/2” 38mm
Source 1W, 350mA or 2.5W, 700mA LED Driver Integral 120V primary, 3W 350mA (1W) or 9W 700mA (2.5W) non-dimmable driver.
3-1/8” 79mm
7/8” 22mm
3-1/4” 83mm
Power Consumption 1.5W / 3W Dimming 0~10V dimming with remote dimmable driver (not included). See page 186190 for Recommended Driver Chart.
4-3/4” 121mm
1-1/2” 38mm
1-3/8” 35mm
Weight 0.65lbs (0.296kg). Material Plated1-1/2” brass, anodized aluminum. RoHS compliant. 3-1/8” 38mm
79mm
1-1/2” 38mm gang box
Mounting Vertically or horizontally positioned face plate mounts to single included). Optimal mounting distance is 18” - 24” (457mm - 610mm) AFF. 7/8”
3-1/4”
Shown as 120° beam Horizontal 3-1/8” plate 79mm
(not
4-3/4”
121mm 83mm 3-1/4” Approval Dry locations. Approved 22mm to US and Canadian standards by CSA.
7/8” 22mm 5/8” 16mm
83mm
Note Can be used as emergency backup lighting in conjunction with Bodine emergency 1-1/2” 1-3/8” LED driver (sold separately). Consult factory.38mm 35mm 1-3/8”
Shown as 120° beam Vertical plate
Wall, Floor & Ceiling Fixtures
Shown as 12° or 30° beam Vertical plate
L14 1W / 2.5W Walkway
4-3/4” 121mm 5/8” 16mm 1-1/2” 38mm
35mm
50 See page 192 for explanation of symbols and IP ratings.
L14 1W, 120° 3000K Std 85 lm
Polar Candela Distribution
Isofootcandle Plot
180°
2
-90°
90°
1
45°
-0°
4
-90°
5
0.1 fc
Mount height: 1 ft Total LLF: 1
Polar Candela Distribution
Isofootcandle Plot
180°
2
-90°
90°
-45°
approx. 70 cd max.
45°
L14
0
1
2
3
20
2
2.5
3
0.5
-0°
4
-90°
5
0.1 fc Mount height: 1 ft Total LLF: 1
0°
Code
1
0 1
Lumen test results provided by LED chip manufacturer.
3
2.5 0.5
3
0°
L14 2.5W, 120° 3000K Std 162 lm
2
20
2
approx. 35 cd max.
1
0 1
-45°
0
Wattage
Color
Beam
Plate
-
Finish -
1 = 1W 2 = 2.5W*
W27S = 2700K, std CRI W30S = 3000K, std CRI W35S = 3500K, std CRI W41S = 4100K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
S = spot (12°) N = narrow flood (30°) W = wide flood (120°)
V = vertical H = horizontal
MC = matte chrome BK = powder coated black BN = brushed nickel
*Only available in W30S & W20H. NOTE: Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
26 27
5/8” 16mm
Image shows L15-1W30SSW30SS-MC
L15
www.mplighting.com
3-1/8” 79mm
1-1/2” 38mm
Application Indoor stair, ramp, aisle, and walkway illumination. Source 2 x 1W, 350mA or 2 x 2.5W, 700mA LEDs.
4-3/4” 121mm
3-1/4” 83mm
Driver Integral 120V primary, 3W 350mA (2W) or 9W 700mA (5W) non-dimmable driver. Power Consumption 3W / 6W
1-3/8” 35mm
Dimming 0~10V dimming with remote dimmable driver (not included). See page 186190 for Recommended Driver Chart.
7/8” 2-1/8” 22mm 54mm
1-1/2” 38mm
Weight 1.03lbs (0.467kg). Material Plated brass, anodized aluminum. RoHS compliant.
3-1/8”
1-1/2”
Wall, Floor & Ceiling Fixtures
Shown as 12° or 30° beam
L15 2 x 1W / 2.5W Up and Down Walkway
Shown as 120° beam
Mounting Vertically positioned face plate mounts to38mm a single gang box (not included).79mm Approval Dry locations. Approved to US and Canadian standards by CSA.
4-3/4” 121mm
3-1/4”
83mm Note Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory. 7/8” 2-1/8” 22mm 54mm
1-3/8” 35mm
1-5/8” 41mm
1-1/2” 38mm
50 See page 192 for explanation of symbols and IP ratings.
L15 2 x 1W, 12° 3000K Std 170 lm
Polar Candela Distribution
Isofootcandle Plot
180°
2
-90°
90°
1
0
2
approx. 750 cd max.
45°
3
-0°
4
-90°
5
Polar Candela Distribution
2
-90°
90°
1
0
2 -45°
approx. 1500 cd max.
45°
4
-90°
5
2
3
Mount height: 1 ft Total LLF: 1
0°
L15
1
0.1 fc
3
-0°
0
20 2.5 0.5
1
Code
3
Isofootcandle Plot
180°
Lumen test results provided by LED chip manufacturer.
2
Mount height: 1 ft Total LLF: 1
0°
L15 2 x 2.5W, 12° 3000K Std 324 lm
1
20 1.0 0.2 0.1 fc
1
-45°
0
Wattage
Color UP
Beam UP
Color Down
Beam Down
-
Finish -
1 = 1W 2 = 2.5W*
W27S = 2700K, std CRI W30S = 3000K, std CRI W35S = 3500K, std CRI W41S = 4100K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
S = spot (12°) N = narrow flood (30°) W = wide flood (120°)
W27S = 2700K, std CRI W30S = 3000K, std CRI W35S = 3500K, std CRI W41S = 4100K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
S = spot (12°) N = narrow flood (30°) W = wide flood (120°)
MC = matte chrome BK = powder coated black BN = brushed nickel
*Only available in W30S & W20H. NOTE: Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
28 29
1-5/8” 41mm
Image shows L16-1W30SWV-S6
L16
www.mplighting.com
Shown as Vertical plate
Application Outdoor / indoor wall, stair, and walkway illumination. 1/8” 3mm
Source 1W, 350mA or 2.5W, 700mA LED
3-3/8” 86mm
1-1/8” 29mm
Driver Integral 120V primary, 3W 350mA (1W) or 9W 700mA (2.5W) non-dimmable driver.
5” 127mm
3-1/4” 83mm
Power Consumption 1.5W / 3W Dimming 0~10V dimming with remote dimmable driver (not included). See page 186190 for Recommended Driver Chart.
2-1/2” 64mm
Weight 1.83lbs (0.832kg). Material 316 stainless steel. RoHS compliant.
1/8” 3mm
Ø2-1/2” Ø64mm
3-3/8” 86mm
1-1/8” 29mm
Mounting Vertically or horizontally positioned face plate mounts to a single gang box (not included). Optimal mounting distance is 18”3-1/4” - 24” (457mm - 610mm) AFF.
Shown as Horizontal plate
Wall, Floor & Ceiling Fixtures
L16 1W / 2.5W Walkway
5” 127mm
83mm
Approval Wet and dry locations. Approved to US and Canadian standards by CSA. Note Can be used as emergency backup lighting in conjunction with Bodine emergency 2-1/2” Ø2-1/2” 64mm Ø64mm LED driver (sold separately). Consult factory.
66 See page 192 for explanation of symbols and IP ratings.
L16 1W, 30° 3000K Std 57 lm
Polar Candela Distribution
Isofootcandle Plot
180°
2
-90°
90°
1
0
2
approx. 275 cd max.
45°
4
-90°
5
2
-90°
90°
1
0
2 -45°
approx. 530 cd max.
45°
0
1
2
3
20 2.5 0.5
1
0.1 fc
3
-0°
4
-90°
5
Mount height: 1 ft Total LLF: 1
0°
L16
0.1 fc
Isofootcandle Plot
180°
Code
3
Mount height: 1 ft Total LLF: 1
Polar Candela Distribution
Lumen test results provided by MP Lighting integrating sphere (see page 194).
2
3
-0°
0°
L16 2.5W, 30° 3000K Std 96 lm
1
20 10 0.5
1
-45°
0
Wattage
Color
Beam
Plate
-
Finish -
1 = 1W 2 = 2.5W*
W27S = 2700K, std CRI W30S = 3000K, std CRI W35S = 3500K, std CRI W41S = 4100K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
S = spot (12°) N = narrow flood (30°) W = wide flood (120°)
V = vertical H = horizontal
S6 S6 = stainless steel 316
*Only available in W30S & W20H. NOTE: Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
30 31
Image shows L17-1W30SNW30SW-S6
L17
www.mplighting.com
Application Outdoor / indoor wall, stair, and walkway illumination. 1/8” 3mm
Source 2 x 1W, 350mA or 2 x 2.5W, 700mA LEDs.
3-3/8” 86mm
2-1/2” 64mm
Driver Integral 120V primary, 3W 350mA (2W) or 9W 700mA (5W) non-dimmable driver. 5” 127mm
3-1/4” 83mm
Power Consumption 3W / 6W Dimming 0~10V dimming with remote dimmable driver (not included). See page 186190 for Recommended Driver Chart.
2-1/2” 64mm
Weight 3.06lbs (1.39kg).
1-1/8” 29mm
Ø2-1/2” Ø64mm
Material 316 stainless steel. RoHS compliant.
Wall, Floor & Ceiling Fixtures
L17 2 x 1W / 2.5W Up and Down Walkway
Mounting Vertically positioned face plate mounts to a single gang box (not included). Approval Wet and dry locations. Approved to US and Canadian standards by CSA. Notes Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
66 See page 192 for explanation of symbols and IP ratings.
L17 2 x 1W, 12° 3000K Std 170 lm
Polar Candela Distribution
Isofootcandle Plot
180°
2
-90°
90°
1
0
2
approx. 700 cd max.
45°
4
-90°
5
0.1 fc
Isofootcandle Plot
180°
2
-90°
90°
1
0
2 -45°
approx. 1300 cd max.
45°
1
2
3
0.1 fc
3
-0°
4
-90°
5
Mount height: 1 ft Total LLF: 1
0°
L17
0
20 5 0.5
1
Code
3
Mount height: 1 ft Total LLF: 1
Polar Candela Distribution
Lumen test results provided by LED chip manufacturer.
2
3
-0°
0°
L17 2 x 2.5W, 12° 3000K Std 324 lm
1
20 10 0.5
1
-45°
0
Wattage
Color UP
Beam UP
Color Down
Beam Down
-
Finish -
1 = 1W 2 = 2.5W*
W27S = 2700K, std CRI W30S = 3000K, std CRI W35S = 3500K, std CRI W41S = 4100K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
S = spot (12°) N = narrow flood (30°) W = wide flood (120°)
W27S = 2700K, std CRI W30S = 3000K, std CRI W35S = 3500K, std CRI W41S = 4100K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
S = spot (12°) N = narrow flood (30°) W = wide flood (120°)
S6 S6 = stainless steel 316
*Only available in W30S & W20H. NOTE: Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
32 33
Image shows L18-1W30SNV-S6
L18
www.mplighting.com
Shown as Vertical plate
Application Outdoor / indoor wall, stair, and walkway illumination. Source 1W, 350mA or 2.5W, 700mA LED Driver Integral 120V primary, 3W 350mA (1W) or 9W 700mA (2.5W) non-dimmable driver.
1-1/8” 29mm
Power Consumption 1.5W / 3W
Material 316 stainless steel. RoHS compliant.
1-3/4” 44mm
3-3/8” 86mm
2-1/2” 64mm
5” 127mm
3-1/4” 83mm
Dimming 0~10V dimming with remote dimmable driver (not included). See page 186190 for Recommended Driver Chart. Weight 1.92lbs (0.873kg).
3-3/8” 86mm
2-1/2” 64mm
2-1/8” 54mm
Shown as Horizontal plate
1-1/8” 29mm
Mounting Vertically or horizontally positioned face plate mounts to a single gang box (not included). Optimal mounting distance is 18”3-1/4” - 24” (457mm - 610mm) AFF.
Wall, Floor & Ceiling Fixtures
L18 1W / 2.5W Walkway
5” 127mm
83mm
Approval Wet and dry locations. Approved to US and Canadian standards by CSA. Notes Can be used as emergency backup lighting in conjunction 1-3/4” with Bodine emergency 2-1/8” 44mm 54mm LED driver (sold separately). Consult factory.
66 See page 192 for explanation of symbols and IP ratings.
L18 1W, 30° 3000K Std 57 lm
Polar Candela Distribution
Isofootcandle Plot
180°
2
-90°
90°
1
0
2
approx. 275 cd max.
45°
4
-90°
5
2
-90°
90°
1
0
2 -45°
approx. 530 cd max.
45°
0
1
2
3
20 2.5 0.5
1
0.1 fc
3
-0°
4
-90°
5
Mount height: 1 ft Total LLF: 1
0°
L18
0.1 fc
Isofootcandle Plot
180°
Code
3
Mount height: 1 ft Total LLF: 1
Polar Candela Distribution
Lumen test results provided by MP Lighting integrating sphere (see page 194).
2
3
-0°
0°
L18 2.5W, 30° 3000K Std 96 lm
1
20 10 0.5
1
-45°
0
Wattage
Color
Beam
Plate
-
Finish -
1 = 1W 2 = 2.5W*
W27S = 2700K, std CRI W30S = 3000K, std CRI W35S = 3500K, std CRI W41S = 4100K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
S = spot (12°) N = narrow flood (30°) W = wide flood (120°)
V = vertical H = horizontal
S6 S6 = stainless steel 316
*Only available in W30S & W20H. NOTE: Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
34 35
Image shows L19-1W30SNW30SN-S6
L19
www.mplighting.com
Application Outdoor / indoor wall, stair, and walkway illumination.
3-3/8” 86mm
2-1/2” 64mm
Source 2 x 1W, 350mA or 2 x 2.5W, 700mA LEDs. Driver Integral 120V primary, 3W 350mA (2W) or 9W 700mA (5W) non-dimmable driver.
3-1/4” 83mm
Power Consumption 3W / 6W Dimming 0~10V dimming with remote dimmable driver (not included). See page 186190 for Recommended Driver Chart.
1/8” 3mm
Weight 3.24lbs (1.47kg).
5” 127mm
2-1/2” 64mm
1-1/8” 29mm
2-1/8” 54mm
Material 316 stainless steel. RoHS compliant.
Wall, Floor & Ceiling Fixtures
L19 2 x 1W / 2.5W Up and Down Walkway
Mounting Vertically positioned face plate mounts to a single gang box (not included). Approval Wet and dry locations. Approved to US and Canadian standards by CSA. Notes Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
66 See page 192 for explanation of symbols and IP ratings.
L19 2 x 1W, 120° 3000K Std 170 lm
Polar Candela Distribution
Isofootcandle Plot
180°
2
-90°
90°
1
0
2
approx. 28 cd max.
45°
4
-90°
5
Polar Candela Distribution
Isofootcandle Plot
180°
2
-90°
90°
1
0
approx. 55 cd max.
45°
4
-90°
5
L19
3
Mount height: 1 ft Total LLF: 1
0°
Code
2
0.1 fc
3
-0°
1
1
2 -45°
0
20 5
1
Lumen test results provided by LED chip manufacturer.
3
Mount height: 1 ft Total LLF: 1
0°
L19 2 x 2.5W, 120° 3000K Std 324 lm
2
0.1 fc
3
-0°
1
20 2.5 1
1
-45°
0
Wattage
Color UP
Beam UP
Color Down
Beam Down
-
Finish -
1 = 1W 2 = 2.5W*
W27S = 2700K, std CRI W30S = 3000K, std CRI W35S = 3500K, std CRI W41S = 4100K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
S = spot (12°) N = narrow flood (30°) W = wide flood (120°)
W27S = 2700K, std CRI W30S = 3000K, std CRI W35S = 3500K, std CRI W41S = 4100K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
S = spot (12°) N = narrow flood (30°) W = wide flood (120°)
S6 S = stainless steel 316
*Only available in W30S & W20H. NOTE: Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
36 37
Image shows L21-1W30SF-S3
L21
www.mplighting.com
3/4” 19mm
Application Indoor stair, ramp, aisle, and walkway illumination. Source 1W, 350mA or 2.5W, 700mA LED
3-1/2” 89mm
Driver Integral 120V primary, 3W 350mA (1W) or 3W 700mA (2.5W) non-dimmable driver.
Ø2-1/2” Ø64mm
Power Consumption 1.5W / 3W 1-3/8” 35mm
Dimming 0~10V dimming with remote dimmable driver (not included). See page 186190 for Recommended Driver Chart. Weight 0.99lbs (0.45kg). Material 303 stainless steel and polycarbonate lens. RoHS compliant.
1/4” 6mm
Ø4-5/8” Ø117mm
Wall, Floor & Ceiling Fixtures
L21 1W / 2.5W Walkway
Mounting Mounts to standard 4” (102mm) octagonal box (1-1/2” / 38mm minimum depth). Optimal mounting distance is 18” - 24” (457mm - 610mm) AFF. Approval Dry locations. Approved to US and Canadian standards by CSA. Note Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
50 See page 192 for explanation of symbols and IP ratings.
L21 1W 3000K Std 85 lm
Polar Candela Distribution 180°
Isofootcandle Plot
135°
0 1 2 3 4 4 3 2
-90°
90°
approx. 4 cd max. 0°
L21 2.5W 3000K Std 162 lm
-90°
180°
1
0.1 fc
4
Mount height: 1 ft Total LLF: 1
Isofootcandle Plot 0 1 2 3 4 4 3 2
-90°
90°
approx. 7.5 cd max.
Code
-0° -90°
Color
-
7
8
0.2
1 0 1 2 3
2.5
0.1 fc
0.5
4
Lens F
1 = 1W 2 = 2.5W*
5 6
Mount height: 1 ft Total LLF: 1
45°
Wattage
8
0.5
135°
0°
7
0.2
1 0 1 2 3
45°
Polar Candela Distribution
Lumen test results provided by LED chip manufacturer.
L21
-0°
5 6
W27S = 2700K, std CRI W30S = 3000K, std CRI W35S = 3500K, std CRI W41S = 4100K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
F = frosted
Finish -
S3 S3 = stainless steel 303
*Only available in W30S & W20H. NOTE: Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
38 39
Image shows L22-1W30SF-S3
L22
www.mplighting.com
3/4” 19mm
Application Outdoor / indoor wall, stair, and walkway illumination. Source 1W, 350mA or 2.5W, 700mA LED
3-1/2” 89mm
Driver Integral 120V primary, 3W 350mA (1W) or 3W 700mA (2.5W) non-dimmable driver.
Ø2-1/2” Ø64mm
Power Consumption 1.5W / 3W Dimming 0~10V dimming with remote dimmable driver (not included). See page 186190 for Recommended Driver Chart.
1-3/4” 44mm
Weight 0.99lbs (0.45kg). Material 303 stainless steel and polycarbonate lens. RoHS compliant.
1/4” 6mm
Ø4-5/8” Ø117mm
Wall, Floor & Ceiling Fixtures
L22 1W / 2.5W Walkway
Mounting Mounts to standard 4” (102mm) octagonal box (1-1/2” / 38mm minimum depth). Use outdoor rated box for outdoor applications. Optimal mounting distance is 18”-24” (457mm-610mm) AFF. Approval Wet locations. Approved to US and Canadian standards by CSA. Note Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
66 See page 192 for explanation of symbols and IP ratings.
L22 1W 3000K Std 85 lm
Polar Candela Distribution 180°
Isofootcandle Plot
135°
0 1 2 3 4 4 3 2
-90°
90°
approx. 4 cd max. 0°
L22 2.5W 3000K Std 162 lm
-90°
180°
1
0.1 fc
4
Mount height: 1 ft Total LLF: 1
Isofootcandle Plot 0 1 2 3 4 4 3 2
-90°
90°
approx. 7.5 cd max.
Code
-0° -90°
Color
-
7
8
0.2
1 0 1 2 3
2.5
0.1 fc
0.5
4
Lens F
1 = 1W 2 = 2.5W*
5 6
Mount height: 1 ft Total LLF: 1
45°
Wattage
8
0.5
135°
0°
7
0.2
1 0 1 2 3
45°
Polar Candela Distribution
Lumen test results provided by LED chip manufacturer.
L22
-0°
5 6
W27S = 2700K, std CRI W30S = 3000K, std CRI W35S = 3500K, std CRI W41S = 4100K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
F = frosted
Finish -
S3 S3 = stainless steel 303
*Only available in W30S & W20H. NOTE: Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
40 41
Image shows L31-1W30S-MC
L31
www.mplighting.com
Shown as Vertical plate
Application Indoor stair, ramp, aisle, and walkway illumination. Source 1W, 350mA or 2.5W, 700mA LED Driver Integral 120V primary, 3W 350mA (1W) or 3W 700mA (2.5W) non-dimmable driver. Power Consumption 1.5W / 3W Dimming 0~10V dimming with remote dimmable driver (not included). See page 186190 for Recommended Driver Chart. Weight 0.57lbs (0.258kg). Material Plated brass and polycarbonate cylinder lens. RoHS compliant.
3-1/4” 83mm 3-1/4” 83mm
7/8” 22mm 7/8” 22mm
4-5/8” 117mm 4-5/8” 117mm
3-1/4” 83mm 3-1/4” 83mm 3-1/8” 79mm 3-1/8” 79mm
Ø1” Ø25mm Ø1” Ø25mm
Shown as Horizontal plate
Wall, Floor & Ceiling Fixtures
L31 1W / 2.5W Walkway
Mounting Vertically or horizontally positioned face plate mounts to a single gang box (not included). Approval Dry locations. Approved to US and Canadian standards by CSA. Note Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
50 See page 192 for explanation of symbols and IP ratings.
L31 1W, 30° 3000K Std 85 lm
Polar Candela Distribution 180°
Isofootcandle Plot
135°
0 1 2 3 4 4 3 2
-90°
approx. 25 cd max. 0°
-0°
8
0.2 2.5 0.5 0.1 fc
Mount height: 1 ft Total LLF: 1
Polar Candela Distribution
Lumen test results provided by LED chip manufacturer.
-90°
180°
7
4
-90°
45°
L31 2.5W, 30° 3000K Std 162 lm
Isofootcandle Plot
135°
0 1 2 3 4
5 6
7
8
4 3 2
approx. 48 cd max.
Code
1 0 1 2 3
90°
5
0°
L31
1 0 1 2 3
90°
5
5 6
-0°
0.2 0.1 fc
4
-90°
Mount height: 1 ft Total LLF: 1
45°
Wattage
5 1
Color
-
Finish -
1 = 1W 2 = 2.5W*
W27S = 2700K, std CRI W30S = 3000K, std CRI W35S = 3500K, std CRI W41S = 4100K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
MC = matte chrome S3 = stainless steel 303
*Only available in W30S & W20H. NOTE: Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
42 43
Image shows L32-1W30S-MC
L32
www.mplighting.com
Shown as Vertical plate
Application Indoor stair, ramp, aisle, and walkway illumination. Source 1W, 350mA or 2.5W, 700mA LED Driver Integral 120V primary, 3W 350mA (1W) or 3W 700mA (2.5W) non-dimmable driver. Power Consumption 1.5W / 3W Dimming 0~10V dimming with remote dimmable driver (not included). See page 186190 for Recommended Driver Chart. Weight 0.57lbs (0.258kg). Material Plated brass and polycarbonate cube lens. RoHS compliant.
3-1/4” 83mm 3-1/4” 83mm
7/8” 22mm 7/8” 22mm 3-1/4” 83mm 3-1/4”
4-5/8” 117mm 4-5/8” 117mm
83mm 3-1/8” 79mm 3-1/8”
1” Sq. 25mm 1” Sq. Sq.
79mm
25mm Sq.
Shown as Horizontal plate
Wall, Floor & Ceiling Fixtures
L32 1W / 2.5W Walkway
Mounting Vertically or horizontally positioned face plate mounts to a single gang box (not included). Approval Dry locations. Approved to US and Canadian standards by CSA. Note Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
50 See page 192 for explanation of symbols and IP ratings.
L32 1W, 30° 3000K Std 85 lm
Polar Candela Distribution 180°
Isofootcandle Plot
135°
0 1 2 3 4 4 3 2
-90°
approx. 27 cd max. 0°
-0°
8
0.2 2.5 0.5 0.1 fc
Mount height: 1 ft Total LLF: 1
Polar Candela Distribution
Lumen test results provided by LED chip manufacturer.
-90°
180°
7
4
-90°
45°
L32 2.5W, 30° 3000K Std 162 lm
Isofootcandle Plot
135°
0 1 2 3 4
5 6
7
8
4 3 2
approx. 52 cd max.
Code
1 0 1 2 3
90°
0°
L32
1 0 1 2 3
90°
5 6
-0°
0.2 0.1 fc
4
-90°
Mount height: 1 ft Total LLF: 1
45°
Wattage
5 1
Color
-
Finish -
1 = 1W 2 = 2.5W*
W27S = 2700K, std CRI W30S = 3000K, std CRI W35S = 3500K, std CRI W41S = 4100K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
MC = matte chrome S3 = stainless steel 303
*Only available in W30S & W20H. NOTE: Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
44 45
Image shows L33-1W30S-S6
L33
www.mplighting.com
Shown as Vertical plate
Application Outdoor / indoor wall, stair, and walkway illumination. Source 1W, 350mA or 2.5W, 700mA LED Driver Integral 120V primary, 3W 350mA (1W) or 9W 700mA (2.5W) non-dimmable driver. Power Consumption 1.5W / 3W Dimming 0~10V dimming with remote dimmable driver (not included). See page 186190 for Recommended Driver Chart. Weight 1.34lbs (0.609kg). Material 316 stainless steel and polycarbonate cylinder lens. RoHS compliant.
3-1/4” 83mm 3-1/4” 83mm
7/8” 22mm 7/8” 22mm 3-1/4” 83mm 3-1/4” 83mm 1-3/4” 44mm 1-3/4” 44mm
4-5/8” 117mm 4-5/8” 117mm Ø1” Ø25mm Ø1” Ø25mm
Shown as Horizontal plate
Wall, Floor & Ceiling Fixtures
L33 1W / 2.5W Walkway
Mounting Vertically or horizontally positioned face plate mounts to a single gang box (not included). Approval Wet locations. Approved to US and Canadian standards by CSA. Note Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
66 See page 192 for explanation of symbols and IP ratings.
L33 1W, 30° 3000K Std 85 lm
Polar Candela Distribution 180°
Isofootcandle Plot
135°
0 1 2 3 4 4 3 2
-90°
approx. 25 cd max. 0°
-0°
8
0.2 2.5 0.5 0.1 fc
Mount height: 1 ft Total LLF: 1
Polar Candela Distribution
Lumen test results provided by LED chip manufacturer.
-90°
180°
7
4
-90°
45°
L33 2.5W, 30° 3000K Std 162 lm
Isofootcandle Plot
135°
0 1 2 3 4
5 6
7
8
4 3 2
approx. 48 cd max.
Code
1 0 1 2 3
90°
5
0°
L33
1 0 1 2 3
90°
5
5 6
-0°
Mount height: 1 ft Total LLF: 1
Color
-
Finish -
1 = 1W 2 = 2.5W*
0.2 0.1 fc
4
-90°
45°
Wattage
5 1
W27S = 2700K, std CRI W30S = 3000K, std CRI W35S = 3500K, std CRI W41S = 4100K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
S6 S6 = stainless steel 316
*Only available in W30S & W20H. NOTE: Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
46 47
Image shows L34-1W30S-S6
L34
www.mplighting.com
Shown as Vertical plate
Application Outdoor / indoor wall, stair, and walkway illumination. Source 1W, 350mA or 2.5W, 700mA LED Driver Integral 120V primary, 3W 350mA (1W) or 9W 700mA (2.5W) non-dimmable driver. Power Consumption 1.5W / 3W Dimming 0~10V dimming with remote dimmable driver (not included). See page 186190 for Recommended Driver Chart.
3-1/4” 83mm 3-1/4” 83mm 1-3/4” 44mm 1-3/4” 44mm
Weight 1.34lbs (0.609kg). Material 316 stainless steel and polycarbonate cube lens. RoHS compliant.
3-1/4” 83mm 3-1/4” 83mm
7/8” 22mm 7/8” 22mm
4-5/8” 117mm 4-5/8” 117mm 1” Sq. 25mm 1” Sq. Sq. 25mm Sq.
Shown as Horizontal plate
Wall, Floor & Ceiling Fixtures
L34 1W / 2.5W Walkway
Mounting Vertically or horizontally positioned face plate mounts to a single gang box (not included). Approval Wet locations. Approved to US and Canadian standards by CSA. Note Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
66 See page 192 for explanation of symbols and IP ratings.
L34 1W, 30° 3000K Std 85 lm
Polar Candela Distribution 180°
Isofootcandle Plot
135°
0 1 2 3 4 4 3 2
-90°
approx. 27 cd max. 0°
-0°
8
0.2 2.5 0.5 0.1 fc
Mount height: 1 ft Total LLF: 1
Polar Candela Distribution
Lumen test results provided by LED chip manufacturer.
-90°
180°
7
4
-90°
45°
L34 2.5W, 30° 3000K Std 162 lm
Isofootcandle Plot
135°
0 1 2 3 4
5 6
7
8
4 3 2
approx. 52 cd max.
Code
1 0 1 2 3
90°
0°
L34
1 0 1 2 3
90°
5 6
-0°
Mount height: 1 ft Total LLF: 1
Color
-
Finish -
1 = 1W 2 = 2.5W*
0.2 0.1 fc
4
-90°
45°
Wattage
5 1
W27S = 2700K, std CRI W30S = 3000K, std CRI W35S = 3500K, std CRI W41S = 4100K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
S6 S6 = stainless steel 316
*Only available in W30S & W20H. NOTE: Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
48 49
Image shows L35-3W30S-MA
L35
www.mplighting.com
Shown as Vertical plate
Application Outdoor / indoor wall, stair, and walkway illumination. Source 3.5W, 350mA or 6.5W, 700mA LED Driver Integral 120V primary, 3W 350mA (3.5W) or 9W 700mA (6.5W) non-dimmable driver. Power Consumption 4W / 8W Dimming 0~10V dimming with remote dimmable driver (not included). See page 186190 for Recommended Driver Chart.
3-1/4” 83mm 3-1/4” 83mm
3/8” 10mm 3/8” 10mm 3-1/4” 83mm 3-1/4” 83mm
4-3/4” 121mm 4-3/4” 121mm
2-3/8” 60mm 2-3/8” 60mm
1-3/4” 45mm 1-3/4” 45mm
Weight 1.18lbs (0.537kg). Material Anodized aluminum and polycarbonate lens. RoHS compliant.
Shown as Horizontal plate
Wall, Floor & Ceiling Fixtures
L35 3.5W / 6.5W Walkway
Mounting Face plate mounts vertically or horizontally to a single gang box (not included). Approval Wet and dry locations. Approved to US and Canadian standards by CSA. Notes Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
66 See page 192 for explanation of symbols and IP ratings.
L35 3.5W 3000K Std 250 lm
Polar Candela Distribution 180°
Isofootcandle Plot
135°
0
2
4
6
8
10
4 2 -90°
90°
0°
-0°
4
-90°
6
0.1 fc
Mount height: 1 ft Total LLF: 1
45°
L35 6.5W 3000K Std 475 lm
Polar Candela Distribution
Lumen test results provided by LED chip manufacturer.
-90°
180°
10 2.5 0.5
0 2
approx. 70 cd max.
Isofootcandle Plot
135°
0
2
4
6
8
10
4 2 90°
0°
Code L35
Wattage -
0
-0°
4
-90°
6
1 0.5
0.1 fc
Mount height: 1 ft Total LLF: 1
45°
Color W30S
3 = 3.5W 6 = 6.5W
20 5
2
approx. 140 cd max.
W30S = 3000K, std CRI
Finish MA = matte clear anodized BA = black anodized
NOTE: Standard CRI has a value of 75~82.
50 51
Image shows L36-3W30S-MA
L36
www.mplighting.com
1-7/8” 48mm
Application Outdoor / indoor wall, stair, and walkway illumination. Source 3.5W, 350mA or 6.5W, 700mA LED
1/4” 6mm
Driver Integral 120V primary, 3W 350mA (3.5W) or 9W 700mA (6.5W) non-dimmable driver. Power Consumption 4W / 8W Dimming 0~10V dimming with remote dimmable driver (not included). See page 186190 for Recommended Driver Chart.
5/8” 16mm
3/8” 10mm
45°
3-1/4” 83mm 3-1/4” 83mm
2-3/8” 60mm 4-3/4” 121mm
Weight 1.4lbs (0.636kg). Material Anodized aluminum and polycarbonate lens. RoHS compliant.
Wall, Floor & Ceiling Fixtures
L36 3.5W / 6.5W Walkway
Mounting Face plate mounts horizontally to single gang box (not included). Approval Wet and dry locations. Approved to US and Canadian standards by CSA. Notes Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
66 See page 192 for explanation of symbols and IP ratings.
L36 3.5W 3000K Std 250 lm
Polar Candela Distribution 180°
Isofootcandle Plot
135°
0 1 2 3 4
approx. 33 cd max. -90°
1 0 1 2 3
90°
-0°
Polar Candela Distribution
Lumen test results provided by LED chip manufacturer.
-90°
L36
0 1 2 3 4
1 0 1 2 3
90°
-
8
20 10 0.5 0.1 fc
Mount height: 1 ft Total LLF: 1
45°
Color W30S
3 = 3.5W 6 = 6.5W
7
4
-90°
Wattage
5 6
4 3 2
-0°
Code
10 5 0.5 0.1 fc
Isofootcandle Plot
135°
approx. 65 cd max.
0°
8
Mount height: 1 ft Total LLF: 1
45°
L36 6.5W 3000K Std 475 lm
180°
7
4
-90° 0°
5 6
4 3 2
W30S = 3000K, std CRI
Finish MA = matte clear anodized BA = black anodized
NOTE: Standard CRI has a value of 75~82.
52 53
Image shows L37-3W30S-MA
L37
www.mplighting.com
2” 51mm
Application Outdoor / indoor wall, stair, and walkway illumination. Source 3.5W, 350mA or 6.5W, 700mA LED Driver Integral 120V primary, 3W 350mA (3.5W) or 9W 700mA (6.5W) non-dimmable driver. Power Consumption 4W / 8W Dimming 0~10V dimming with remote dimmable driver (not included). See page 186190 for Recommended Driver Chart. Weight 2.19lbs (0.994kg). Material Anodized aluminum and polycarbonate lens. RoHS compliant.
2-3/4” 70mm
7/8” 22mm
1-1/8” 29mm
Ø4-1/2” Ø114mm
1/4” 6mm
45°
2-3/8” 60mm
Wall, Floor & Ceiling Fixtures
L37 3.5W / 6.5W Walkway
Mounting Mounts to standard 4” (102mm) octagonal box (1-1/2” / 38mm minimum depth). Use outdoor rated box for outdoor applications. Optimal mounting distance is 18”-24” (457mm-610mm) AFF. Approval Wet and dry locations. Approved to US and Canadian standards by CSA. Note Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
66 See page 192 for explanation of symbols and IP ratings.
L37 3.5W 3000K Std 250 lm
Polar Candela Distribution 180°
Isofootcandle Plot
135°
0 1 2 3 4
approx. 33 cd max. -90°
1 0 1 2 3
90°
-0°
Polar Candela Distribution
Lumen test results provided by LED chip manufacturer.
-90°
L37
135°
0 1 2 3 4
1 0 1 2 3
90°
-
8
20 10 0.5 0.1 fc
Mount height: 1 ft Total LLF: 1
45°
Color W30S
3 = 3.5W 6 = 6.5W
7
4
-90°
Wattage
5 6
4 3 2
-0°
Code
10 5 0.5 0.1 fc
Isofootcandle Plot
approx. 65 cd max.
0°
8
Mount height: 1 ft Total LLF: 1
45°
L37 6.5W 3000K Std 475 lm
180°
7
4
-90° 0°
5 6
4 3 2
W30S = 3000K, std CRI
Finish MA = matte clear anodized BA = black anodized
NOTE: Standard CRI has a value of 75~82.
54 55
Image shows L91-2W30SNC0-MA
L91
www.mplighting.com
Wall, Floor & Ceiling Fixtures
L91 2.5W Downlight Application Outdoor / indoor wall mounted for up or down illumination.
3-3/8” 3-3/8” 86mm 86mm
Source 2.5W LED Driver Integral 120V primary, 3W 700mA non-dimmable driver.
4-1/2” 4-1/2” Sq.Sq. 114mm 114mm Sq.Sq.
3-7/8” 3-7/8” 98mm 98mm
Power Consumption 3W Dimming 0~10V dimming with remote dimmable driver (not included). See page 186190 for Recommended Driver Chart.
Ø2-5/8” Ø2-5/8” Ø67mm Ø67mm
3-1/4” 3-1/4” 83mm 83mm
Weight 2.02lbs (0.914kg) Material Anodized aluminum, insert trim with 1/4” (6mm) thick tempered glass lens. RoHS compliant.
Shown with angle bracket
Mounting Mounts to standard 4” (102mm) octagonal box (1-1/2”/ 38mm minimum depth). Can be positioned facing up or down.
Shown with no angle bracket
Approval Wet and dry locations. Approved to US and Canadian standards by CSA. Note Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
66 See page 192 for explanation of symbols and IP ratings.
L91 12°, clear lens 3000K Std 162 lm
Polar Candela Distribution
Isofootcandle Plot
180°
1
-90°
90°
0
1 -45°
approx. 1350 cd max.
45°
-90°
2
Mount height: 6 ft Total LLF: 1
Polar Candela Distribution
Isofootcandle Plot
180°
1
-90°
Lumen test results provided by LED chip manufacturer.
90°
0
-45°
approx. 550 cd max.
45°
-90°
2
Mount height: 6 ft Total LLF: 1
Wattage -
1
-0°
0°
L91
0
10 2.5 0.5 0.1 fc
1
Code
1
-0°
0°
L91 30°, clear lens 3000K Std 162 lm
0
20 5 0.5 0.1 fc
Color
Beam
Lens
Angle Bracket
2 2 = 2.5W
Finish -
W30S = 3000K, std CRI W20H = 2000K, high CRI
S = spot (12°) N = narrow flood (30°) W = wide flood (120°)
C = clear F = frosted
0 = no angle 30 = 30° angle X = custom (30° max.)
MA MA = matte clear anodized
NOTE: Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
56 57
Image shows L92-2W30SNC0-24MA
L92
www.mplighting.com
Wall, Floor & Ceiling Fixtures
L92 2.5W Bollard Shown with angle bracket
Application Outdoor walkway and area illumination.
Shown with no angle bracket
Source 2.5W LED Driver Integral 120V primary, 3W 700mA non-dimmable driver. Power Consumption 3W Dimming 0~10V dimming with remote dimmable driver (not included). See page 186190 for Recommended Driver Chart. Weight 7.15lbs (3.245kg) based on 24” (610mm) post. Material Anodized aluminum, insert trim with 1/4” (6mm) thick tempered glass lens. RoHS compliant. 7-3/8” 187mm
Mounting Mounts to 24” (610mm), 36” (614mm) or 48” (1219mm) anodized aluminum post. Comes with 24” (610mm) Cabtire lead inside post.
3/4” 19mm
Approval Wet and dry locations. Approved to US and Canadian standards by CSA. Note Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
5-1/2” 140mm
Ø2-5/8” Ø67mm
1-3/4” 44mm
3-7/8” 98mm
66 See page 192 for explanation of symbols and IP ratings.
L92 30°, clear lens 3000K Std 162 lm
Polar Candela Distribution
Isofootcandle Plot
180° -90°
1
2
90°
0
1
1
H (post height) 0 -45°
approx. 500 cd max.
45°
-0° -90°
1
0.1 fc Mount height: 3 ft Total LLF: 1
Polar Candela Distribution L92 120°, clear lens 180° 3000K Std approx. 162 lm -90° 55 cd max.
2-3/8” 60mm
Isofootcandle Plot 1
2
90°
0
2-3/8” 60mm
1
1/4” 6mm
1 0
-45°
45°
-0° -90°
Code
Wattage -
20 2.5 1
1
0.5
0.1 fc
2
4-1/2” 114mm
Mount height: 3 ft Total LLF: 1
0°
L92
5
2
0°
Lumen test results provided by LED chip manufacturer.
20 0.5
Color
Beam
Lens
Angle Bracket
2 2 = 2.5W
Post Height (H) -
W30S = 3000K, std CRI W20H = 2000K, high CRI
S = spot (12°) N = narrow flood (30°) W = wide flood (120°)
C = clear F = frosted
0 = no angle 30 = 30° angle X = custom (30° max.)
6” Sq. 152mm Sq.
Finish MA
24 = 24” (610mm) 36 = 36” (914mm) 48 = 48” (1219mm)
MA = matte clear anodized
NOTE: Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
58 59
Image shows L97-1W30SN-36MA
L97
www.mplighting.com
Wall, Floor & Ceiling Fixtures
L97 6W/15W Bollard
8-1/2” 216mm
Application Outdoor walkway and area illumination. Source 6 x 1W, 350mA or 6 x 2.5W, 700mA LEDs Driver L97: Remote 120V primary, 350mA (6W) or 700mA (15W) driver (not included) LED Input Voltage 24V DC
1-5/8” 5-3/8” x 6-3/8” 41mm 137mm x 162mm
Power Consumption L97: 8W / 18W Dimming 0~10V dimming with remote dimmable driver and controller (not included). See page 186-190 for Recommended Driver Chart. Weight 9.59lbs (4.35kg) based on 36” (914mm) post.
Post Height
Material Anodized aluminum. 1/4” (6mm) thick polycarbonate lens and silicone gaskets. RoHS compliant. Mounting Mounts to 36” (914mm) or 48” (1219mm) anodized aluminum post. Comes with 24” (610mm) Cabtire lead inside post. Approval Wet and dry locations. Approved to US and Canadian standards by CSA. Notes An appropriate 24V DC LED driver must be used with fixture. Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
1/4” 6mm
4-1/2” 114mm
67
6” Sq. 152mm Sq.
See page 192 for explanation of symbols and IP ratings.
L97 6 x 1W, 30° 3000K Std 510 lm
Polar Candela Distribution
Isofootcandle Plot
180° -90°
1
2
90°
0
1
1 0 -45°
approx. 1300 cd max.
45°
-0° -90°
1 2
Polar Candela Distribution
0.1 fc
-90°
5-3/8” 137mm
Isofootcandle Plot
180°
2
3
90°
1
0
1
2
Post Height
0 -45°
approx. 520 cd max.
45°
2
-90°
3
L97
Wattage
2.5
20
0.5 0.1 fc
1/4” 6mm
Mount height: 3 ft Total LLF: 1
0°
Code
10
1
-0°
1-5/8” 41mm
2
1
Lumen test results provided by LED chip manufacturer.
6-3/8” 162mm
Mount height: 3 ft Total LLF: 1
0°
L97 6 x 2.5W Elliptical 3000K Std 630 lm
8-1/2” 216mm
20 2.5 0.5 0.2
Color
Beam
-
Post Height (H)
4-1/2” 114mm
Finish
6” 152mm
1 = 6 x 1W 2 = 6 x 2.5W*
W27S = 2700K, std CRI W30S = 3000K, std CRI W35S = 3500K, std CRI W41S = 4100K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
S = spot (12°) N = narrow flood (30°) F = flood (60°) E = elliptical (only available in 2.5W)
36 = 36” (914mm) 48 = 48” (1219mm)
MA = matte clear anodized BA = black anodized
*Only available in W30S & W20H. NOTE: Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
60 61
Image shows L98-1W30SN-6MA
L98
www.mplighting.com
Application Outdoor / indoor wall mounted for up or down illumination.
6” 152mm
Source 6 x 1W, 350mA or 6 x 2.5W, 700mA LEDs
3-1/4” 83mm
Driver Remote 120V primary, 350mA (6W) or 700mA (15W) driver (not included). LED Input Voltage 24V DC
5-3/4” 146mm
Power Consumption 8W / 18W Dimming 0~10V dimming with remote dimmable driver and controller (not included). See page 186-190 for Recommended Driver Chart.
1/8” 3mm
4-3/8” 111mm
1-5/8” 41mm
Weight 2.24lbs (1.54kg).
5-3/8” 137mm
Wall, Floor & Ceiling Fixtures
L98 6W/15W LED Wall Sconce
Material Anodized aluminum or 316 stainless steel. 1/4” (6mm) thick polycarbonate lens and silicone gaskets. RoHS compliant. Mounting Mounts to standard octagonal box (not included) via universal round mounting bracket. Comes with standard 6’ (1829 mm) Cabtire water proof lead (longer leads available). Approval Wet and dry locations. Approved to US and Canadian standards by CSA. Notes An appropriate 24V DC LED driver must be used with fixture. Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
67 See page 192 for explanation of symbols and IP ratings.
L98 6 x 1W, 12° 3000K Std 510 lm
Polar Candela Distribution
Isofootcandle Plot
180°
1
-90°
0
-45°
approx. 2700 cd max.
45°
-0° -90°
Mount height: 9 ft Total LLF: 1
Polar Candela Distribution
Isofootcandle Plot
180°
1
-90°
1 -45°
approx. 6000 cd max.
45°
-0°
1
2
20 1 0.2 0.1 fc
2
-90° Mount height: 9 ft Total LLF: 1
0°
L98
0
90° 0
Code
2
2
0°
Lumen test results provided by LED chip manufacturer.
1
20 5 0.5 0.1 fc
1
L98 6 x 2.5W, 12° 3000K Std 972 lm
0
90°
Wattage
Color
Beam
-
Lead Length
Finish
6 = 6’ (1829mm) X = custom
MA = matte clear anodized BA = black anodized S6 = stainless steel 316
1 = 6 x 1W 2 = 6 x 2.5W*
W27S = 2700K, std CRI W30S = 3000K, std CRI W35S = 3500K, std CRI W41S = 4100K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
S = spot (12°) N = narrow flood (30°) F = flood (60°)
*Only available in W30S & W20H. NOTE: Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
62 63
Image shows L99-1W30SFW30SN-6MA
L99
www.mplighting.com
Application Outdoor / indoor wall mounted for up or down illumination. Source 12 x 1W, 350mA or 12 x 2.5W, 700mA LEDs
1/8” 3mm
6” 152mm 4-3/8” 111mm
3-1/4” 83mm
5-3/8” 137mm
Driver Remote 120V primary, 700mA driver (not included). LED Input Voltage 24V DC
1-5/8” 41mm
Power Consumption 17W / 35W
5-3/4” 146mm
Dimming 0~10V dimming with remote dimmable driver and controller (not included). See page 186-190 for Recommended Driver Chart. Weight 5.64lbs (2.56kg).
Wall, Floor & Ceiling Fixtures
L99 2 x 6W/15W LED Wall Sconce
Material Anodized aluminum or 316 stainless steel. 1/4” (6mm) thick polycarbonate lens and silicone gaskets. RoHS compliant. Mounting Mounts to standard octagonal box (not included) via universal round mounting bracket. Comes with standard 6’ (1829 mm) Cabtire water proof lead (longer leads available). Approval Wet and dry locations. Approved to US and Canadian standards by CSA. Notes An appropriate 24V DC LED driver must be used with fixture. Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
67 See page 192 for explanation of symbols and IP ratings.
L99 12 x 1W, 30° 3000K Std 1020 lm
Polar Candela Distribution
Isofootcandle Plot
180°
1
-90°
0
-45°
approx. 1300 cd max.
45°
-0°
2
Mount height: 9 ft Total LLF: 1
Polar Candela Distribution
Isofootcandle Plot
180°
1
-90°
1
2
20 1 0.2
1 -45°
approx. 2400 cd max.
45°
-0°
0.1 fc
2
-90° Mount height: 9 ft Total LLF: 1
0°
L99
0
90° 0
Code
2
-90°
0°
Lumen test results provided by LED chip manufacturer.
1
20 1 0.2 0.1 fc
1
L99 12 x 2.5W, 30° 3000K Std 1944 lm
0
90°
Wattage
Color UP
Beam UP
Color Down
Beam Down
-
Lead Length
Finish
6 = 6’ (1829mm) X = custom
MA = matte clear anodized BA = black anodized S6 = stainless steel 316
1 = 6 x 1W 2 = 6 x 2.5W*
W27S = 2700K, std CRI W30S = 3000K, std CRI W35S = 3500K, std CRI W41S = 4100K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
S = spot (12°) N = narrow flood (30°) F = flood (60°)
W27S = 2700K, std CRI W30S = 3000K, std CRI W35S = 3500K, std CRI W41S = 4100K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
S = spot (12°) N = narrow flood (30°) F = flood (60°)
*Only available in W30S & W20H. NOTE: Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
64 65
Image shows L130-7W30S30-MA
L130
www.mplighting.com
Wall, Floor & Ceiling Fixtures
L130 7.5W Downlight Application Indoor surface mount downlight. Source 3 x 2.5W, 700mA LEDs Driver Integral 120V primary, 9W 700mA non-dimmable driver. Power Consumption 9W Dimming 0~10V dimming with remote dimmable driver (not included). See page 186190 for Recommended Driver Chart. Weight 0.88lbs (0.39kg). Material Anodized aluminum. RoHS compliant. Mounting Mounts to standard octagonal box (not included). Approval Dry locations. Approved to US and Canadian standards by CSA. Note Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
3/4” 19mm
Ø4-3/4” Ø121mm
40 See page 192 for explanation of symbols and IP ratings.
L130 30° 3000K Std 266 lm
Polar Candela Distribution
Illuminance at a Distance
180° -90°
Center Beam FC
90°
-45°
approx. 1400 cd max.
45°
L130 60° 3000K Std 240 lm
Polar Candela Coefficients OfDistribution Utilization 80
-90° RW %:
50 30 1.12 1.12 1.05 1.03 1.00 .96 .94 .91 .90 .86 .86 .81 .82 .78 .79 .74 .76 .71 .73 0°.68 .70 .66
70 RCR: 0 1.12 1 1.08 2 1.03 3 .99 4 .96 -45° 5 .92 6 .89 7 .86 8 .83 9 .80 10 .77
Lumen test results provided by MP Lighting integrating sphere (see page 194).
1.7’
1.7’
6.0’
37.24
3.4’
3.4’
9.0’
16.55
5.0’
5.0’
12.0’
9.31
6.7’
6.7’
15.0’
5.96
8.4’
8.4’
18.0’
4.14
10.1’
10.1’
90° Spread: 31.3°
Illuminance at a Distance Effective Floor Cavity Reflectance: 20%
180°
RCC %:
148.95
0° Spread: 31.3°
0°
Beam Width
3.0’
70 0 70 1.12 1.09 1.02 1.05 .94 1.01 .87 .98 .82 .94 .78 approx..91 .74 450 cd.88 .71 max. .85 .68 .82 .65 .79 .63 .77
90° 50
1.09 1.03 .98 .93 .89 45° .85 .81 .78 .75 .72 .70
50
30 1.09 1.02 .95 .90 .85 .81 .77 .74 .71 .68 .66
30
10
Center Beam FC Beam Width 0 50 30 20 50 30 20 50 30 20 34.951.00 1.00 .96 3.5’ .96 2.7’ 3.0’ 1.05 1.05 1.00 .94 1.05 .96 .90 1.00 .98 .97 .96 .95 .94 .93 .96 .91 8.74 5.4’ 7.0’ 6.0’ .86 .95 .93 .91 .92 .90 .89 .90 .88 .87 3.88 .86 .84 .87 10.5’ .85 8.1’ .91 .88 .85 .89 .82 9.0’ .83 .87 .84 .81 .85 .79 12.0’ .79 2.18 .82 .80 .84 14.0’ .8110.7’ .75 .83 .80 .77 .82 .79 .76 .81 .78 .76 1.40 .76 .73 .78 17.5’ .7513.4’ .80 .76 .74 .79 .72 15.0’ .73 .77 .73 .70 .76 .70 18.0’ .70 0.97 .73 .70 .75 21.1’ .7216.1’ .67 .74 .70 .68 .73 .70 .67 .72 .69 .67 0° Spread: Spread: .71 .67 .6590°.70 .68 .6560.7° .64 .72 .67 48.2° .65 .62 .69 .65 .63 .68 .65 .62 .68 .65 .62
0 0 .94 .90 .85 .82 .78 .75 .71 .69 .66 .64 .61
Coefficients Of Utilization Effective Floor Cavity Reflectance: 20%
RCC %:
Code L130
-
80
RW %: 70 50 RCR:Wattage 01.10 1.10 11.05 1.02 2 .99 .94 3 .94 7 .88 4 .89 .82 5 .84 .76 7 = 63 .80 x 2.5W .71 7 .76 .67 8 .72 .63 9 .68 .59 10 .65 .56
30 1.10 .99 .90 .83 .76 .71 .66 .61 .57 .54 .50
70
50
30
10
0 70 50 30 0 50 30 20 50 30 20 50 30 1.08 .93 1.03 1.03 1.03 .98 Beam 1.10 1.08 1.08 .98 .98 .94 .94 Color .97 1.02 1.00 .98 .86 .96 .94 .93 .93 .91 .90 .89 .88 .87 .97 .93 .89 .80 .90 .87 .84 .87 .84 .82 .84 .82 .79 .92 .86 .82 .74 .84 .80 .77 .81 .78 .76 .79 .77 .72 .87 .80 .75 .69 .78 .74 .71 .77 .73 .70 .75 .72 .66 .83 .75 .70 .64 .74 .69 .65 .72 .68 .65 .71 .67 W30S = 3000K, std CRI beam .65 .60 .61 .78 .71 .69 .64 30 .61 = .6830°.64 .60 .67 .63 .61 .56 .57 .75 .66 .57 = .6460°.60 .56 .63 .59 W20H = 2000K, high.65 CRI .60 60 beam .53 .71 .62 .57 .52 .61 .56 .53 .60 .56 .53 .59 .55 .50 .67 .59 .53 .49 .58 .53 .49 .57 .53 .49 .56 .52 .47 .64 .53 .50of 75~82 .46 .54while .49high .46CRI .55 .50 NOTE: Standard CRI.46 has .55 a value has.49 92.
0 20 0 .94 .93 Finish .87 .85 .80 .79 .74 .73 .69 .68 .64 .63 MA = matte clear anodized .60 .59 .55 .56 = BA black anodized .52 .51 .49 .48 .46 .45
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
66 67
Image shows L131-7W30S30-MA
L131
www.mplighting.com
Wall, Floor & Ceiling Fixtures
L131 7.5W Downlight Application Outdoor / indoor surface mount downlight. Source 3 x 2.5W, 700mA LEDs Driver Integral 120V primary, 9W 700mA non-dimmable driver. Power Consumption 9W Dimming 0~10V dimming with remote dimmable driver (not included). See page 186190 for Recommended Driver Chart. Weight 0.84lbs (0.38kg). Material Anodized aluminum. RoHS compliant. Mounting Mounts to standard octagonal box (not included). Approval Damp and dry locations. Approved to US and Canadian standards by CSA. Note Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
3/4” 19mm
Ø4-3/4” Ø121mm
44 See page 192 for explanation of symbols and IP ratings.
L131 30° 3000K Std 266 lm
Polar Candela Distribution
Illuminance at a Distance
180° -90°
Center Beam FC
90°
-45°
approx. 1400 cd max.
45°
L131 60° 3000K Std 240 lm
Polar Candela Coefficients OfDistribution Utilization 80
-90° RW %:
50 30 1.12 1.12 1.05 1.03 1.00 .96 .94 .91 .90 .86 .86 .81 .82 .78 .79 .74 .76 .71 .73 0°.68 .70 .66
70 RCR: 0 1.12 1 1.08 2 1.03 3 .99 4 .96 -45° 5 .92 6 .89 7 .86 8 .83 9 .80 10 .77
Lumen test results provided by MP Lighting integrating sphere (see page 194).
1.7’
1.7’
6.0’
37.24
3.4’
3.4’
9.0’
16.55
5.0’
5.0’
12.0’
9.31
6.7’
6.7’
15.0’
5.96
8.4’
8.4’
18.0’
4.14
10.1’
10.1’
90° Spread: 31.3°
Illuminance at a Distance Effective Floor Cavity Reflectance: 20%
180°
RCC %:
148.95
0° Spread: 31.3°
0°
Beam Width
3.0’
70 0 70 1.12 1.09 1.02 1.05 .94 1.01 .87 .98 .82 .94 .78 approx..91 .74 450 cd.88 .71 max. .85 .68 .82 .65 .79 .63 .77
90° 50
1.09 1.03 .98 .93 .89 45° .85 .81 .78 .75 .72 .70
50
30 1.09 1.02 .95 .90 .85 .81 .77 .74 .71 .68 .66
30
10
Center Beam FC Beam Width 0 50 30 20 50 30 20 50 30 20 34.951.00 1.00 .96 3.5’ .96 2.7’ 3.0’ 1.05 1.05 1.00 .94 1.05 .96 .90 1.00 .98 .97 .96 .95 .94 .93 .96 .91 8.74 5.4’ 7.0’ 6.0’ .86 .95 .93 .91 .92 .90 .89 .90 .88 .87 3.88 .86 .84 .87 10.5’ .85 8.1’ .91 .88 .85 .89 .82 9.0’ .83 .87 .84 .81 .85 .79 12.0’ .79 2.18 .82 .80 .84 14.0’ .8110.7’ .75 .83 .80 .77 .82 .79 .76 .81 .78 .76 1.40 .76 .73 .78 17.5’ .7513.4’ .80 .76 .74 .79 .72 15.0’ .73 .77 .73 .70 .76 .70 18.0’ .70 0.97 .73 .70 .75 21.1’ .7216.1’ .67 .74 .70 .68 .73 .70 .67 .72 .69 .67 0° Spread: Spread: .71 .67 .6590°.70 .68 .6560.7° .64 .72 .67 48.2° .65 .62 .69 .65 .63 .68 .65 .62 .68 .65 .62
0 0 .94 .90 .85 .82 .78 .75 .71 .69 .66 .64 .61
Coefficients Of Utilization Effective Floor Cavity Reflectance: 20%
RCC %:
Code L131
-
80
RW %: 70 50 RCR:Wattage 01.10 1.10 11.05 1.02 2 .99 .94 3 .94 7 .88 4 .89 .82 5 .84 .76 7 = 63 .80 x 2.5W .71 7 .76 .67 8 .72 .63 9 .68 .59 10 .65 .56
30 1.10 .99 .90 .83 .76 .71 .66 .61 .57 .54 .50
70
50
30
10
0 70 50 30 0 50 30 20 50 30 20 50 30 1.08 .93 1.03 1.03 1.03 .98 Beam 1.10 1.08 1.08 .98 .98 .94 .94 Color .97 1.02 1.00 .98 .86 .96 .94 .93 .93 .91 .90 .89 .88 .87 .97 .93 .89 .80 .90 .87 .84 .87 .84 .82 .84 .82 .79 .92 .86 .82 .74 .84 .80 .77 .81 .78 .76 .79 .77 .72 .87 .80 .75 .69 .78 .74 .71 .77 .73 .70 .75 .72 .66 .83 .75 .70 .64 .74 .69 .65 .72 .68 .65 .71 .67 W30S = 3000K, std CRI beam .65 .60 .61 .78 .71 .69 .64 30 .61 = .6830°.64 .60 .67 .63 .61 .56 .57 .75 .66 .57 = .6460°.60 .56 .63 .59 W20H = 2000K, high.65 CRI .60 60 beam .53 .71 .62 .57 .52 .61 .56 .53 .60 .56 .53 .59 .55 .50 .67 .59 .53 .49 .58 .53 .49 .57 .53 .49 .56 .52 .47 .64 .53 .50of 75~82 .46 .54while .49high .46CRI .55 .50 NOTE: Standard CRI.46 has .55 a value has.49 92.
0 20 0 .94 .93 Finish .87 .85 .80 .79 .74 .73 .69 .68 .64 .63 MA = matte clear anodized .60 .59 .55 .56 = BA black anodized .52 .51 .49 .48 .46 .45
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
68 69
Image shows L134-10W30S30NA-MA
L134
www.mplighting.com
Wall, Floor & Ceiling Fixtures
L134 4W / 10W Downlight Application Outdoor / indoor surface mount downlight. Source 4 x 1W, 350mA or 4 x 2.5W, 700mA LEDs Driver Integral 120V primary, 10W 350mA (4W) or 17W 700mA (10W) nondimmable driver. Power Consumption 6W / 12W Dimming 0~10V dimming with remote dimmable driver (not included). See page 186-190 for Recommended Driver Chart. Weight 2.02lbs (0.92kg). Material Anodized aluminum. RoHS compliant.
1-1/8” 29mm
Mounting Mounts to standard octagonal box (not included).
2-1/8” Sq. 54mm Sq.
6-3/4” Sq. 171mm Sq.
3/8” 10mm
Approval Damp and dry locations. Approved to US and Canadian standards by CSA. Note Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
44 Shown with no accessory (NA)
See page 192 for explanation of symbols and IP ratings.
L134 4 x 2.5W, 30° 3000K Std 396 lm
Polar Candela Distribution
Shown with black cross baffle (CB) Used to reduce glare.
Illuminance at a Distance
180° -90°
Center Beam FC
90°
-45°
approx. 1400 cd max.
45°
L134 4 x 2.5W, 60° 3000K Std 370 lm
Polar Candela Coefficients OfDistribution Utilization RCC %:
70 50 RCR: 01.09 1.09 11.04 1.02 2 .99 .95 3 .95 .89 4 .91 .84 -45° 5 .87 .80 6 .83 .76 7 .80 .72 8 .77 .69 9 .74 .66 10 .71 .63
Lumen test results provided by MP Lighting integrating sphere (see page 194).
30 1.09 1.00 .92 .85 .79 .75 .71 .67 .64 0°.61 .59
1.8’
1.8’
6.0’
39.50
3.6’
3.6’
9.0’
17.56
5.4’
5.4’
12.0’
9.88
7.3’
7.2’
15.0’
6.32
9.1’
9.0’
18.0’
4.39
10.9’
18.8’
90° Spread: 33.3°
Illuminance at a Distance Effective Floor Cavity Reflectance: 20%
180°
80
-90° RW %:
158.00
0° Spread: 33.6°
0°
Beam Width
3.0’
70 0 70 1.09 1.07 .98 1.02 .89 .97 .81 .93 .76 .89 .71 approx..85 .67 550 cd.82 .64 max. .79 .61 .76 .58 .73 .55 .70
90° 50 1.07 1.00 .94 .88 .83 45° .79 .75 .72 .68 .66 .63
30 1.07 .98 .90 .84 .79 .74 .70 .67 .64 .61 .58
50
30
10
Center Beam FC Beam Width 0 50 30 20 50 30 20 50 30 20 3.4’ .94 3.4’ 3.0’ 1.02 1.02 61.72 .98 .98 .98 .92 1.02 .94 .94 .93 .91 .90 .86 .96 .95 .93 .90 .89 .88 15.43 6.8’ 6.8’ 6.0’ .88 .86 .84 .81 .91 .88 .86 .85 .84 .82 .83 .81 .78 10.2’ .86 .82 .80 6.86 .77 9.0’ .81 .7910.1’ .77 .79 .76 .74 13.6’ .81 .77 .74 3.86 .72 12.0’ .78 .7513.5’ .73 .76 .72 .70 .69 .77 .73 .70 .74 .71 .69 .72 .69 .66 17.0’ .74 .70 .66 2.47 .65 15.0’ .71 .6816.9’ .66 .69 .66 .63 20.4’ .70 .66 .63 1.71 .62 18.0’ .68 .6520.3’ .62 .67 .63 .60 .60 .67 .63 .60 .66 .62 .60 58.8° .61 .5859.0° .57 .650° Spread: .63 .60 .57 .64 .60 .57 90° Spread: .55 .62 .58 .55 .62 .58 .55 .61 .57 .55
0 0 .92 .86 .81 .76 .71 .68 .64 .61 .59 .56 .54
Coefficients Of Utilization Effective Floor Cavity Reflectance: 20%
RCC %:
Code L134
80
Wattage RW %: 70 50
-
RCR: 01.09 11.03 2 .97 3 .92 4 =4 4.87x 5 .82 10 =6 4.78x 7 .74 8 .70 9 .66 10 .63
30 1.09 1.09 1.00 .98 .93 .88 .86 .81 .79 .74 1W .74 .68 2.5W* .69 .63 .64 .59 .60 .55 .57 .51 .54 .48
70
Color 50 30
50
30
Beam 0 70 0 50 30 20 50 30 20 .97 .97 .97 1.09 1.06 1.06 1.06 .91 1.01 1.01 1.01 .91 .90 .88 .96 1.01 .98 .96 .85 .95 .93 .91 .85 .83 .81 .85 .95 .91 .87 .78 .88 .85 .82 .80 .76 .74 .77 .90 .84 .80 .72 .82 .78 .75 .74 .71 .68 .76 .72 30 .68= 30° .78 .73 std .66 CRI .70 .85 2700K, W27S = beam .70 .66 .62 .64 .81 .73 .68 .62 .71 .67 .63 W30S = beam .65 .61 .58 .67 .62 60 .58= 60° .68 .63 std .57 CRI .59 .76 3000K, .61 .57 .54 .63 .58 .54 .64 .58 std .53 CRI .54 .72 3500K, W35S = .58 .53 .50 .51 .69 .60 .54 .50 .59 .54 .50 W41S = .55 .50 .47 .55 .50 .47 .56 .51 std .47 CRI .47 .65 4100K, .53 .48 high .44 .52 .44 .62 2000K, W20H = CRI .47 .44 .52 .47 .44
10
0
50 30 Accessories 20 0 .91 .93 .93 .93 .84 .88 .87 .86 .77 .83 .81 .79 .71 .77 .75 .72 .65 .73NA = .69 .67no accessory .60 .68 .65 .62 .56baffle, black .64CB .60= .57cross .52 .60 .56 .53 .49 .57 .53 .50 .45 .54 .50 .47 .43 .51 .47 .44
Finish MA = matte clear anodized BA = black anodized
W30H = 3000K, high CRI *Only available in W30S & W20H. NOTE: Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
70 71
Image shows L135-9W30S30-MA
L135
www.mplighting.com
Application Indoor surface mount downlight. Source 1 x 4.5W, 350mA or 1 x 9.5W, 700mA LED. Driver Remote 120V primary, 8W 350mA (4.5W) or 17W 700mA (9.5W) non-dimmable driver (included). Power Consumption 5W / 11W Dimming 0~10V dimming with remote dimmable driver (not included). See page 186190 for Recommended Driver Chart. Weight 1.14lbs (0.52kg). 5/8” 16mm
Material Anodized aluminum. RoHS compliant.
6” Sq. 152mm Sq.
Wall, Floor & Ceiling Fixtures
L135 4.5W / 9.5W Downlight
Mounting Mounts to standard octagonal box (not included). Approval Dry locations. Approved to US and Canadian standards by CSA. Note Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
40 See page 192 for explanation of symbols and IP ratings.
L135 4.5W, 30° 3000K Std 320 lm
Polar Candela Distribution
Illuminance at a Distance
180° -90°
-45°
approx. 850 cd max.
45°
Polar Candela Coefficients OfDistribution Utilization RCC %: -90° RW %:
RCR: 0 1 2 3 4 -45° 5 6 7 8 9 10
Lumen test results provided by LED chip manufacturer.
180°
80
Beam Width
3.0’
93.74
1.7’
1.7’
6.0’
23.44
3.5’
3.4’
9.0’
10.42
5.2’
5.2’
12.0’
5.86
6.9’
6.9’
15.0’
3.75
8.6’
8.6’
18.0’
2.6
10.4’
10.3’
0° Spread: 32.1°
0°
L135 9.5W, 30° 3000K Std 560 lm
Center Beam FC
90°
90° Spread: 32.0°
Illuminance at a Distance Effective Floor Cavity Reflectance: 20%
70
50
70
50
30
10
0
Center Beam FC Beam Width 70 50 30 0 70 90° 50 30 0 50 30 20 50 30 20 50 30 20 0 1.7’ 1.01 1.7’ 1.07 1.07 1.07 1.03 1.12 1.12 1.12 164.05 1.20 1.20 1.20 1.20 1.17 1.17 1.17 1.01 3.0’ 1.03 1.03 .95 1.15 1.12 1.10 1.08 1.12 1.10 1.08 .95 1.06 1.04 1.03 1.02 1.01 1.00 .99 .98 .97 41.01 3.4’ 3.5’ 6.0’ .90 1.10 1.05 1.02 .98 1.08 1.04 1.00 .90 1.00 .98 .95 .97 .95 .93 .95 .93 .91 5.2’.88 5.2’ .93 .90 .88 .91 .95 .92 .89 18.23 .85 1.05 .99 .95 .91 1.03 .98 .94 .86 9.0’ .86 .89 .86 .83 .87 .91 .87 .84 10.25 .81 1.01 .94 .89 .85 .99 .93 .88 .81 12.0’ .84 .82 6.9’ 6.9’ 45° .77 .97 .89 .84 .80 approx..95 .88 .84 .78 .87 .82 .79 .85 .81 .79 .84 .80 .78 6.56 .78 .75 .80 8.6’.77 8.6’ .83 .78 .75 .81 .91 .84 .79 .74 15.0’ .73 .93 .85 .80 .76 .74 1500 cd .79 .75 .72 .78 .70 .89 .81 .76 .72 .71 max. .88 .81 .76 .71 18.0’ 4.56 .74 .71 .77 10.4’.74 10.3’ .67 .86 .78 .72 .69 .85 .77 .72 .68 .76 .72 .69 .75 .71 .68 .74 .71 .68 0° Spread: Spread: 32.0° .64 .72 .68 .6590°.72 .69 .6632.1° .83 .740°.69 .66 .82 .74 .69 .65 .73 .68 .65 .62 .80 .72 .67 .63 .79 .71 .66 .63 .70 .66 .63 .70 .66 .63 .69 .65 .63
Coefficients Of Utilization Effective Floor Cavity Reflectance: 20%
RCC %:
Code L135
-
80
30
RW %: 70 50 30 0 70 50 30 0 50 30 20 50 30 20 Wattage Color Beam RCR: 0 1.20 1.20 1.20 1.20 1.17 1.17 1.17 1.01 1.12 1.12 1.12 1.07 1.07 1.07 1 1.15 1.12 1.10 1.08 1.12 1.10 1.08 .95 1.06 1.04 1.03 1.02 1.01 1.00 2 1.10 1.05 1.02 .98 1.08 1.04 1.00 .90 1.00 .98 .95 .97 .95 .93 W30S 3 1.05 .99 .95 .91 1.03 .98 .94 .86 .95 .92 .89 .93 .90 .88 4 1.01 .94 .89 .85 .99 .93 .88 .81 .91 .87 .84 .89 .86 .83 4 = 51 x.97 4.5W 20° .81 beam .79 .79= .85 .88 .84 std .78CRI.87 .82 20 .89 .84W30S = .80 .95 3000K, 6 .85 .80 .76 .91 .84 .79 .74 .83 .78 .75 .81 .78 .75 9 = 71 x.93 9.5W 30 = 30° beam .89 .81 .76 .72 .88 .81 .76 .71 .79 .75 .72 .78 .74 .71 8 .86 .78 .72 .69 .85 .77 .72 .68 .76 .72 36 .68 .69= .75 36° .71 beam 9 .83 .74 .69 .66 .82 .74 .69 .65 .73 .69 .66 .72 .68 .65 10 .80 .72 .67 .63 .79 .71 .66 .63 .70 .66 .63 .70 .66 .63
10
0
50 30 20 0 Finish 1.03 1.03 1.03 1.01 .95 .99 .98 .97 .90 .95- .93 .91 .85 .91 .88 .86 .81 .87 .84 .82 MA = .77 clear anodized .84 .80 .78 matte .73 .80 .77 .74 BA = black anodized .70 .77 .74 .71 .67 .74 .71 .68 .64 .72 .68 .65 .62 .69 .65 .63
NOTE: Standard CRI has a value of 75~82.
72 73
Image shows L141-NINDW30S30R1-W
L141 13W Recessed Downlight Application Indoor downlight with field replaceable LED lamp. Source 13W, 700mA LED Driver Integral 120V AC or 277V AC, 17W 700mA dimmable or non-dimmable driver (please specify). Power Consumption 15W
6-1/8” 156mm
Dimming 0-10V (120V input only, dimmable driver optional). A control lead is required to connect each dimmable driver to the controlling dimmer switch. See page 186-190 for Recommended Driver Chart. Weight Non-insulated, 5.17lbs (2.35kg). Insulated, 6.21lbs (2.82kg). Retrofit, 5.16 lbs (2.34kg). Material Aluminum. RoHS compliant.
Ø4-7/8” Ø124mm
Wall, Floor & Ceiling Fixtures
Shown as insulated housing (IC), white finish (W) and round trim (R)
L141
www.mplighting.com
7-5/8” 194mm
Mounting Mounts into insulated ceiling box. Recessed mount non-insulated version to ceiling with spring clip. Ceiling Cutout Size 4” (102mm).
9-1/2” 241mm
Approval Dry and damp locations. Approved to US and Canadian standards by CSA.
Up to 24” / 610mm
Note Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
Shown as non-insulated housing (NI), white finish (W) and round trim (R)
44 See page 192 for explanation of symbols and IP ratings.
L141 30° 3000K Std 459 lm
Polar Candela Distribution
-90°
Center Beam FC
90°
-45°
approx. 2700 cd max.
45°
5-3/8” 137mm
Beam Width
3.0’
299.72
1.5’
1.5’
6.0’
74.93
3.1’
3.1’
9.0’
33.30
4.6’
4.6’
12.0’
18.73
6.2’
6.2’
15.0’
11.99
7.7’
7.7’
18.0’
8.33
9.2’
9.2’
0° Spread: 28.8°
0°
la Distribution
Illuminance at a Distance
180°
90° Spread: 28.8°
Ø4-7/8” Shown 7-5/8” as retrofit housing (R), 194mm Ø124mm black finish (B) and square
Illuminance at a Coefficients Distance Of Utilization
trim (S) Effective Floor Cavity Reflectance: 20%
180° 90°
3.0’ 6.0’ 9.0’
approx. 2700 cd max.
45°
12.0’ 15.0’ 18.0’ 0°
0°
80 70 50 30 10 RCC %: Center Beam FC Beam Width RW %: 70 50 30 0 70 50 30 0 50 30 20 50 30 20 50 30 20 299.72 1.5’1.191.5’ 1.19 1.17 1.17 1.17 1.00 1.11 1.11 1.11 1.07 1.07 1.07 1.02 1.02 1.02 RCR: 0 1.19 1.19 1 1.15 1.12 1.10 1.08 1.12 1.10 1.08 .96 1.06 1.05 1.03 1.02 1.01 1.00 .99 .98 .97 74.93 3.1’ 3.1’ 2 1.10 1.06 1.02 .99 1.08 1.04 1.01 .91 1.01 .98 .96 .98 .96 .94 .95 .94 .92 Lumen test 33.30 4.6’ .964.6’ 3 1.06 1.00 .92 1.04 .99 .95 .87 .96 .93 .90 .94 .91 .89 .92 .89 .87 provided 4 1.01 .95 .87 1.00results .94 .89 .83 .92 .88 .85 .90 .87 .84 .88 .85 .83 18.73 6.2’ .906.2’ 5 .97 .90 .85 .82 .96by .89 MP Lighting .85 .79 .88 .84 .80 .86 .82 .80 .84 .82 .79 11.99 7.7’ .817.7’ 6 .93 .86 .77 .92integrating .85 .80 .75 .84 .80 .76 .82 .79 .76 .81 .78 .75 7 .90 .82 .73 .89 .81 .77 .72 .80 .76 .73 .79 .75 .72 .78 .75 .72 8.33 9.2’ .779.2’ sphere (see 8 .86 .78 .73 .70 .85 .78 .73 .69 .77 .73 .69 .76 .72 .69 .75 .72 .69 Spread: 28.8° 90° .75 Spread: 9 .83 .70 28.8° .67 .82page .75194). .70 .66 .74 .69 .66 .73 .69 .66 .72 .69 .66 10 .80 .72 .67 .64 .79 .72 .67 .63 .71 .67 .64 .70 .66 .64 .70 .66 .63
0 0 1.00 .95 .91 .86 .82 .78 .74 .71 .68 .65 .62
9-1/2” 241mm 4-3/4” 121mm
Sq.4-7/8” Sq.124mm
Effective Floor Cavity Reflectance: 20%
50 30 0 1.19 1.19 1.19 1.12 1.10 1.08 1.06 1.02 .99 1.00 .96 .92 .95 .90 .87 .90 .85 .82 .86 .81 .77 .82 .77 .73 .78 .73 .70 .75 .70 .67 .72 .67 .64
70
50
30
10
70 50 30 0 50 30 20 50 30 20 50 30 20 1.17 1.17 1.17 1.00 1.11 1.11 1.11 1.07 1.07 1.07 1.02 1.02 1.02 1.12 1.10 1.08 .96 1.06 1.05 1.03 1.02 1.01 1.00Housing .99 .98 .97 Code 1.08 1.04 1.01 .91 1.01 .98 .96 .98 .96 .94 .95 .94 .92 1.04 .99 .95 .87 .96 .93 .90 .94 .91 .89 .92 .89 .87 L141 1.00 .94 .89 .83 .92 .88 .85 - .90 .87 .84 .88 .85 .83 .96 .89 .85 .79 .88 .84 .80 .86 .82 .80 .84 .82 .79 .92 .85 .80 .75 .84 .80 .76 .82 .79 .76 .81 .78 .75 NI = .89 .81 .77 .72 .80 .76 .73 .79 .75 non-insulated .72 .78 .75 .72 .85 .78 .73 .69 .77 .73 .69 .76 .72 insulated .69 .75 .72 .69 IC = .82 .75 .70 .66 .74 .69 .66 .73 .69 .66 .72 .69 .66 R .66 = retrofit (old.66code: .79 .72 .67 .63 .71 .67 .64 .70 .64 .70 .63
5-3/8” 137mm
11-1/8” 283mm
Of Utilization 80
Up to 24” / 610mm 5/8” 16mm
0 0 1.00 .95 .91 .86 .82 .78 .74 .71 .68 .65 NI).62
Dimming
Color
Reflector
Trim
Input Voltage
Finish -
ND = non-dimmable D = dimmable (not available in 277V)
W30S = 3000K, std CRI W50S = 5000K, std CRI
30 = 30° 45 = 45°
R = round S = square
1 = 120V 2 = 277V*
W = white B = black
*277V only available in non-dimmable driver (ND).
74
NOTE: Standard CRI has a value of 75~82.
75
Image shows L142-ICND9W30S36-WH
L142
www.mplighting.com
Application Indoor adjustable LED downlight. Source 9.5W, 700mA LED Driver Integral 120V primary, 17W 700mA dimmable or non-dimmable driver (please specify). Power Consumption 12W Dimming 0-10V (120V input only, dimmable driver optional). A control lead is required to connect each dimmable driver to the controlling dimmer switch. See page 186-190 for Recommended Driver Chart. Weight Insulated, 3.55lbs (1.6kg). Non-insulated, 2.51lbs (1.14kg). Material Aluminum. RoHS compliant.
Wall, Floor & Ceiling Fixtures
Shown as insulated housing (IC) with white finish (WH).
L142 9.5W Recessed Downlight (0~30°)
<30°
Mounting Mounts into insulated ceiling box with spring clips.
6-1/8” 156mm
Ceiling Cutout Size Ø3.5” (Ø89mm). Approval Dry and damp locations. Approved to US and Canadian standards by CSA. Note Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
Ø4-1/8” Ø105mm
7-5/8” 194mm
44 See page 192 for explanation of symbols and IP ratings. 9-1/2” 241mm Up to 24” (610mm)
L142 36° 3000K Std 176 lm
Polar Candela Distribution
Illuminance at a Distance
180° -90°
Lumen test results provided by MP Lighting integrating sphere (see page 194).
Center Beam FC
90°
-45°
approx. 1100 cd max.
45°
118.14
1.5’
1.5’
6.0’
29.54
3.0’
3.0’
9.0’
13.13
4.4’
4.5’
12.0’
7.38
5.9’
6.0’
15.0’
4.73
7.4’
7.5’
18.0’
3.28
8.9’
9.0’
0° Spread: 27.8°
0°
Beam Width
3.0’
90° Spread: 28°
Coefficients Of Utilization Effective Floor Cavity Reflectance: 20%
RCC %:
Code L142
-
80
RW %: 70 50 30 0 RCR: 0 .63 .63 .63 .63 1 .60 .59 .58 .56 2 .58 .55 .53 .52 3 .55 .52 .50 .48 4 .53 .50 .47 .45 5 .51Housing .48 .45 .43 6 .50 .46 .43 .41 7 .48 .44 .41 .40 8 .46 .42IC.40 .38 9 .45 .41 .38 .37 10 .44 .40 .37 .35
IC = insulated
70 70 .62 .59 .57 .54 .52 .51 .49 .47 .46 .44 .43
50 .62 .58 .54 .52 .49 .47 .45 .44 .42 .41 .39
50 30 .62 .57 .53 .50 .47 .45 .43 .41 .40 .38 .37
0 .52 .49 .47 .45 .43 .41 .40 .38 .37 .36 .35
50 30 20 .59 .59 .59 .55 .54 .54 .53 .51 .50 .50 .48 .47 .48 .46 .45 .46 .44 .42 Dimming .44 .42 .41 .43 .41 .39 .41 .39 .38 .40 .38 .36 .39 .37 .35
ND = non-dimmable D = dimmable
30 50 .56 .53 .51 .49 .47 .45 .44 .42 .41 .40 .38
30 .56 .52 .50 .47 .45 .43 .42 .40 .39 .38 .36
10 20 50 30 .56 .53 .53 .52 .51 .51 .49 .49 .48 .46 .47 .46 .44 .46 .44 .42 .44 .43 Wattage .40 .43 .41 .39 .42 .40 .37 9.40 .39 .36 .39 .37 .35 .38 .36
9 = 9.5W
0 20 .53 .50 .47 .45 .43 .42 .40 .39 .37 .36 .35
0 .52 .49 .47 .44 .43 .41 .39 .38 .37 .35 .34
Color
W30S = 3000K, std CRI W41S = 4100K, std CRI
Beam
Finish -
16 = 16° 22 = 22° 36 = 36°
WH = white BK = black
NOTE: Standard CRI has a value of 75~82.
76 77
Image shows L151-3W30S30-MA
L151
www.mplighting.com
Application Outdoor / indoor wall, stair, and walkway illumination. Source 3 x 1W, 350mA LEDs Driver Remote 120V primary, 350mA constant current or 12V constant voltage driver (not included). LED Input Voltage 12V DC Power Consumption 4W Dimming 0~10V dimming with remote dimmable driver (not included). See page 186190 for Recommended Driver Chart.
3/4” 19mm
4-5/8” 117mm
Wall, Floor & Ceiling Fixtures
L151 3 x 1W Surface Mount Strip Light
Weight 0.30lbs (0.135kg). Material Anodized aluminum. RoHS compliant. Mounting Surface mount with 6” (152mm) wire lead. Approval Wet and dry locations. Approved to US and Canadian standards by CSA.
1-1/4” 32mm
Note Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
5-1/4” 133mm
66 See page 192 for explanation of symbols and IP ratings.
L151 12° 3000K Std 255 lm
Polar Candela Distribution
Isofootcandle Plot
180°
1
-90°
0
-45°
approx. 1100 cd max.
45°
-0° -90°
2
Mount height: 3 ft Total LLF: 1
Polar Candela Distribution
Isofootcandle Plot
180°
1
-90°
-45°
approx. 600 cd max.
2
45°
-0° -90°
2 3
Mount height: 3 ft Total LLF: 1
Wattage -
1
20 1 0.2 0.1 fc
1
0°
L151
0
90° 0
Code
2
3
0°
Lumen test results provided by LED chip manufacturer.
1
20 1 0.2 0.1 fc
1
L151 30° 3000K Std 255 lm
0
90°
Color
Beam
3 3 = 3 x 1W
Finish -
W27S = 2700K, std CRI W30S = 3000K, std CRI W35S = 3500K, std CRI W41S = 4100K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
12 = 12° beam 30 = 30° beam 60 = 60° beam
MA MA = matte clear anodized
NOTE: Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
78 79
Image shows L181M-W30S-BA and RAL181-4-BA
L181
www.mplighting.com 1/4 5/8 2 3/8
9” 229mm
Application Modular bottle rack system for restaurants, bars, and wine cellars with 100% no UV and no heat.
top arm module
1” 25mm
Source 1W, 350mA LED per arm
3/4” 19mm
adjustable**
Driver Remote 120V primary, 350mA driver (not included). LED Input Voltage 4V DC
8” 203mm
adjustable
Power Consumption 1.5W per arm Dimming 0~10V dimming with remote driver (not included). Requires minimum load of LEDs. See page 186-190 for Recommended Driver Chart.
middle arm module
Wall, Floor & Ceiling Fixtures
L181 Modular Wine Rack
Weight 10.8lb (4.898kg) with 3-1/2’ (1.073m) rail. Material Black anodized aluminum. RoHS compliant. Mounting Mounts to wall with 6” (152mm) wire lead per arm.
bottom arm module
Approval Interior rated. Approved to US and Canadian standards by CSA.
custom length rail
40
Note: 9” (229mm) spacing recommended between arm modules.
See page 192 for explanation of symbols and IP ratings.
L181T 3000K Std 85 lm
Polar Candela Distribution
Illuminance at a Distance
180° -90°
Lumen test results provided by LED chip manufacturer.
Center Beam FC
90°
-45°
approx. 30 cd max.
45°
475.78
0.4’
0.4’
0.5’
118.95
0.8’
0.9’
0.8’
52.86
1.3’
1.3’
1.0’
29.74
1.7’
1.7’
1.3’
19.03
2.1’
2.2’
1.5’
13.22
2.5’
2.6’
0° Spread: 79.6°
0°
Top Arm Module has LED and no cross bars. Code L181T
Color -
Top arm
W27S = 2700K, std CRI W30S = 3000K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
L181M
Bottom Arm Module has cross bars and no LED. Code
BA
L181B
BA = black anodized
Bottom arm
Middle arm
W27S = 2700K, std CRI W30S = 3000K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
Finish -
BA BA = black anodized
Bottom arm
Color -
90° Spread: 81.9°
Finish
Middle Arm Module has LED and cross bars. Code
Beam Width
0.3’
Rail comes with rubber cover. Finish
Code
BA
RAL181
BA = black anodized
Rail
Length -
Finish -
X = custom by foot
BA BA = black anodized
NOTE: Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
80 81
Image shows L51-1W30S120-MA
L51
www.mplighting.com
Application Showcases, kitchen cabinets, restaurant millwork, or wine cellars. Source 1W, 350mA or 2.5W, 700mA LED Driver Remote 120V primary, 350mA (1W) or 700mA (2.5W) driver (not included). 1” 25mm
LED Input Voltage 4V DC Power Consumption 1.5W / 3W
Cabinet Fixtures
L51 1W / 2.5W Puck Light
1/2” 13mm
Dimming 0~10V dimming with remote dimmable driver (not included). See page 186190 for Recommended Driver Chart. Weight 0.06lbs (0.029kg).
Ø1-1/2” Ø38mm
Material Aluminum. RoHS compliant. Mounting Surface mount to cabinet millwork. Comes with 6’ (1829mm) wire lead. Optimal spacing is 18” - 24” (457mm - 610mm). Approval Dry locations. Approved to US and Canadian standards by CSA.
40 See page 192 for explanation of symbols and IP ratings.
L51 1W, 120° 3000K Std 62 lm
Polar Candela Distribution
Illuminance at a Distance
180° -90°
Center Beam FC
90°
-45°
approx. 30 cd max.
45°
123.49
1.2’
1.2’
1.0’
30.87
2.5’
2.4’
1.5’
13.72
3.7’
3.7’
2.0’
7.72
5.0’
4.9’
2.5’
4.94
6.2’
6.1
3.0’
3.43
7.5’
7.3’
0° Spread: 102.4°
0°
L51 2.5W, 120° 3000K Std 104 lm
Polar Candela Distribution
90° Spread: 101.5°
Illuminance at a Distance
180° -90°
Lumen test results provided by MP Lighting integrating sphere (see page 194).
Center Beam FC
90°
-45°
approx. 55 cd max.
45°
Code
218.25
1.3’
1.3’
1.0’
54.56
2.5’
2.5’
1.5’
24.25
3.8’
3.8’
2.0’
13.64
5.0’
5.0’
2.5’
8.73
6.3’
6.3
3.0’
6.06
7.6’
7.5’
0° Spread: 103.2°
Wattage
Color
W27S = 2700K, std CRI W30S = 3000K, std CRI W35S = 3500K, std CRI W41S = 4100K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
90° Spread: 102.8°
Beam 120
1 = 1W 2 = 2.5W*
Beam Width
0.5’
0°
L51
Beam Width
0.5’
120 = 120° beam
Finish MA = matte clear anodized BA = black anodized BN = brushed nickel
*Only available in W30S & W20H. NOTE: Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
82 83
Image shows L52-1W30S120-MA
L52
www.mplighting.com
Application Showcases, kitchen cabinets, restaurant millwork, or wine cellars. Source 1W, 350mA or 2.5W, 700mA LED Driver Remote 120V primary, 350mA (1W) or 700mA (2.5W) driver (not included). LED Input Voltage 4V DC
120°
Cabinet Fixtures
Ø1-5/8” Ø41mm
L52 1W / 2.5W Puck Light
Power Consumption 1.5W / 3W 1/2” 13mm
Dimming 0~10V dimming with remote dimmable driver (not included). See page 186190 for Recommended Driver Chart.
Ø1-3/8” Ø35mm
1/8” 3mm
Weight 0.07lbs (0.03kg). Ø2” Ø51mm
Material Anodized aluminum. RoHS compliant. Mounting Recessed mount to cabinet millwork. Comes with 6’ (1829mm) wire lead. Optimal spacing is 18” - 24” (457mm - 610mm). Cutout Size Ø1-3/8” (Ø35mm) Approval Dry locations. Approved to US and Canadian standards by CSA.
40 See page 192 for explanation of symbols and IP ratings.
L52 1W, 120° 3000K Std 59 lm
Polar Candela Distribution
Illuminance at a Distance
180° -90°
Center Beam FC
90°
-45°
approx. 30 cd max.
45°
123.00
1.5’
1.5’
1.0’
30.75
3.1’
3.0’
1.5’
13.67
4.6’
4.5’
2.0’
7.69
6.2’
6.0’
2.5’
4.92
7.7’
7.5’
3.0’
3.42
9.2’
9.0’
0° Spread: 113.9°
0°
L52 2.5W, 120° 3000K Std 97 lm
Polar Candela Distribution
90° Spread: 112.4°
Illuminance at a Distance
180° -90°
Lumen test results provided by MP Lighting integrating sphere (see page 194).
Center Beam FC
90°
-45°
approx. 55 cd max.
45°
Code
217.51
1.5’
1.5’
1.0’
54.38
3.0’
3.1’
1.5’
24.17
4.5’
4.6’
2.0’
13.59
6.0’
6.2’
2.5’
8.70
7.5’
7.7’
3.0’
6.04
9.0’
9.3’
0° Spread: 112.4°
Wattage
Color
W27S = 2700K, std CRI W30S = 3000K, std CRI W35S = 3500K, std CRI W41S = 4100K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
90° Spread: 114.1°
Beam 120
1 = 1W 2 = 2.5W*
Beam Width
0.5’
0°
L52
Beam Width
0.5’
120 = 120° beam
Finish MA = matte clear anodized BA = black anodized BN = brushed nickel
*Only available in W30S & W20H. NOTE: Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
84 85
Image shows L55-3W27S120-MA
L55
www.mplighting.com
1-1/2” 38mm
Application Showcases, kitchen cabinets, restaurant millwork, or wine cellars. Source 3 x 1W, 350mA LEDs Driver Remote 120V or 277V primary, 350mA driver (not included). LED Input Voltage 12V DC Power Consumption 4W
Cabinet Fixtures
L55 3W Puck Light
1/2” 13mm
Dimming 0~10V dimming with remote dimmable driver (not included). See page 186190 for Recommended Driver Chart. Ø2-3/8” Ø60mm
Weight 0.19lbs (0.087kg). Material Anodized aluminum. RoHS compliant. Mounting Surface mount to cabinet millwork. Comes with 6’ (1829mm) wire lead. Optimal spacing is 18” - 24” (457mm - 610mm). Approval Dry locations. Approved to US and Canadian standards by CSA.
40 See page 192 for explanation of symbols and IP ratings.
L55 120° 3000K Std 94 lm
Polar Candela Distribution
Illuminance at a Distance
180° -90°
Lumen test results provided by MP Lighting integrating sphere (see page 194).
Center Beam FC
90°
-45°
approx. 90 cd max.
45°
376.89
0.8’
0.8’
1.0’
94.22
1.6’
1.5’
1.5’
41.88
2.4’
2.3’
2.0’
23.56
3.2’
3.1’
2.5’
15.08
4.0’
3.9’
3.0’
10.47
4.8’
4.6’
0° Spread: 77.4°
0°
Code L55
Wattage -
Color
3 3 = 3 x 1W
Beam Width
0.5’
Beam 120
W27S = 2700K, std CRI W30S = 3000K, std CRI W35S = 3500K, std CRI W41S = 4100K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
90° Spread: 75.2°
120 = 120° beam
Finish MA = matte clear anodized BA = black anodized BN = brushed nickel
NOTE: Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
86 87
Image shows L56-3W30S120-MA
L56
www.mplighting.com
1-1/2” 38mm
Application Showcases, kitchen cabinets, restaurant millwork, or wine cellars. Source 3 x 1W, 350mA LEDs Driver Remote 120V or 277V primary, 350mA driver (not included).
integral friction fit spring for easy mounting
LED Input Voltage 12V DC
Cabinet Fixtures
L56 3W Puck Light
Power Consumption 4W Dimming 0~10V dimming with remote dimmable driver (not included). See page 186190 for Recommended Driver Chart.
1/8” 3mm
Ø2-1/2” Ø64mm
3/8” 10mm
Weight 0.37lbs (0.167kg). Material Anodized aluminum. RoHS compliant.
Ø3” Ø76mm
Mounting Recessed mount to cabinet millwork with friction fit spring clip. Comes with 6’ (1829mm) wire lead. Optimal spacing is 18” - 24” (457mm - 610mm). Cutout Size Ø2-1/2” (Ø64mm) Approval Dry locations. Approved to US and Canadian standards by CSA.
40 See page 192 for explanation of symbols and IP ratings.
L56 120° 3000K Std 63 lm
Polar Candela Distribution
Illuminance at a Distance
180° -90°
Lumen test results provided by MP Lighting integrating sphere (see page 194).
Center Beam FC
90°
-45°
approx. 90 cd max.
45°
371.99
0.6’
0.6’
1.0’
93.00
1.2’
1.1’
1.5’
41.33
1.8’
1.7’
2.0’
23.25
2.4’
2.3’
2.5’
14.88
3.0’
2.8’
3.0’
10.33
3.6’
3.4’
0° Spread: 61.5°
0°
Code L56
Wattage -
Color
3 3 = 3 x 1W
Beam Width
0.5’
Beam 120
W27S = 2700K, std CRI W30S = 3000K, std CRI W35S = 3500K, std CRI W41S = 4100K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
90° Spread: 58.9°
120 = 120° beam
Finish MA = matte clear anodized BA = black anodized BN = brushed nickel
NOTE: Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
88 89
Image shows L57F-3W30S60NA-MA
L57
www.mplighting.com
Application Showcases, kitchen cabinets, restaurant millwork, or wine cellars. Source 3 x 1W, 350mA LEDs integral friction fit spring for easy mounting
Driver Remote 120V primary, 350mA constant current or 12V constant voltage driver (not included). Shown as semi-recessed (S) mount with no accessory (NA).
LED Input Voltage 12V DC
3/8” 10mm
Ø2-1/2” Ø64mm
1/2” 13mm
Cabinet Fixtures
L57 3W Recessed Puck Light
Power Consumption 4W Dimming 0~10V dimming with remote dimmable driver (not included). See page 186-190 for Recommended Driver Chart.
Ø3” Ø76mm
Weight 0.37lbs (0.167kg). Material Anodized aluminum. RoHS compliant.
integral friction fit spring for easy mounting
Ø2-1/2” Ø64mm
Mounting Semi-recessed or fully-recessed fixture body mounts to millwork with friction fit spring clip. Comes with 6’ (1829mm) wire lead. Fullyrecessed mount requires minimum of 7/8” (22mm) depth. 7/8” 22mm
Cutout Size Ø2-1/2” (Ø64mm)
7/8” 22mm
Approval Dry locations. Approved to US and Canadian standards by CSA.
Ø3” Ø76mm
Shown as fully-recessed (F) mount with silver metal shroud (SH).
40 See page 192 for explanation of symbols and IP ratings.
L57 30°, NA 3000K Std 186 lm
Polar Candela Distribution
Illuminance at a Distance
180° -90°
Center Beam FC
90°
-45°
45°
approx. 650 cd max.
L57 60°, NA 3000K Std 184 lm Lumen test results provided by MP Lighting integrating sphere (see page 194).
Polar Candela Distribution
0.5’
0.5’
2.0’
145.90
1.1’
1.0’
3.0’
64.84
1.6’
1.5’
4.0’
36.47
2.1’
2.0’
5.0’
23.34
2.6’
2.5’
6.0’
16.21
3.2’
3.0’
90° Spread: 28.1°
Illuminance at a Distance
180° -90°
Center Beam FC
90°
-45°
approx. 230 cd max.
45°
Mount
L57 S = semi-recessed F = fully-recessed
97.32
1.0’
1.0’
2.0’
24.33
1.9’
2.0’
3.0’
10.81
2.9’
3.0’
4.0’
6.08
3.9’
4.0’
5.0’
3.89
4.8’
5.0’
6.0’
2.70
5.8’
6.0’
Wattage -
Beam Width
1.0’
0° Spread: 51.6°
0°
Code
583.60
0° Spread: 29.7°
0°
Beam Width
1.0’
90° Spread: 53.3°
Color
Beam
Accessories
3 3 = 3 x 1W
Finish -
W27S = 2700K, std CRI W30S = 3000K, std CRI W35S = 3500K, std CRI W41S = 4100K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
30 = 30° beam 60 = 60° beam
NA = no accessory SH = metal shroud, silver SHB = metal shroud, black
MA = matte clear anodized BA = black anodized BN = brushed nickel
NOTE: Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
90 91
Image shows L58R-2W30S120-MA
L58
www.mplighting.com
Shown as round cover (R)
Application Showcases, kitchen cabinets, restaurant millwork, or wine cellars. Source 2.5W, 700mA LED
integral friction fit spring for easy mounting
Driver Remote 120V primary, 700mA driver (not included). LED Input Voltage 4V DC
Ø2-1/2” Ø64mm
1/8” 3mm
1/2” 13mm
Cabinet Fixtures
L58 2.5W Recessed Puck Light
Power Consumption 3W Dimming 0~10V dimming with remote dimmable driver (not included). See page 186190 for Recommended Driver Chart.
Ø3” Ø76mm
Weight 0.074lbs (0.034kg).
Shown as square cover (S)
Material Anodized aluminum. RoHS compliant. Mounting Recessed mount to millwork with friction fit spring clip. Comes with 6’ (1829mm) wire lead. Optimal spacing is 18” - 24” (457mm - 610mm). Cutout Size Ø2-1/2” (Ø64mm) Approval Dry locations. Approved to US and Canadian standards by CSA.
integral friction fit spring for easy mounting 1/8” 3mm
20
Ø2-1/2” Ø64mm
1/2” 13mm
See page 192 for explanation of symbols and IP ratings. 3” Sq. 76mm Sq.
L58 120° 3000K Std 93 lm Lumen test results provided by MP Lighting integrating sphere (see page 194).
Polar Candela Distribution
Illuminance at a Distance
180° -90°
Center Beam FC
90°
-45°
approx. 60 cd max.
45°
Code
Cover
L58
Wattage -
R = round cover S = square cover
242.86
1.1’
1.2’
1.0’
60.72
2.3’
2.5’
1.5’
26.98
3.4’
3.7’
2.0’
15.18
4.5’
4.9’
2.5’
9.71
5.7’
6.2’
3.0’
6.75
6.8’
7.4’
0° Spread: 97.0°
0°
Color
2 2 = 2.5W
Beam Width
0.5’
90° Spread: 102.1°
Beam 120
W30S = 3000K, std CRI W20H = 2000K, high CRI
120 = 120° beam
Finish -
MA MA = matte clear anodized
NOTE: Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
92 93
Image shows L59R-4W30S120-MA
L59
www.mplighting.com
Shown as round cover (R)
Application Showcases, kitchen cabinets, restaurant millwork, or wine cellars. Source 3.7W, 350mA LED
integral friction fit spring for easy mounting
Transformer Remote 120V primary. 12V low voltage magnetic transformer (not included). LED Input Voltage 10V DC
Ø2-1/2” Ø64mm
1/8” 3mm
1/2” 13mm
Cabinet Fixtures
L59 3.7W Recessed Puck Light
Power Consumption 4W Dimming Low voltage magnetic dimer. Please consult factory.
Ø3” Ø76mm
Weight 0.074lbs (0.034kg). Material Anodized aluminum. RoHS compliant.
Shown as square cover (S)
Mounting Recessed mount to millwork with friction fit spring clip. Comes with 6’ (1829mm) wire lead. Optimal spacing is 18” - 24” (457mm - 610mm). Cutout Size Ø2-1/2” (Ø64mm) Approval Dry locations. Approved to US and Canadian standards by CSA. integral friction fit spring for easy mounting
20
1/8” 3mm
See page 192 for explanation of symbols and IP ratings.
Ø2-1/2” Ø64mm
1/2” 13mm
3” Sq. 76mm Sq.
L59 120° 3000K Std 240 lm
Lumen test results provided by LED chip manufacturer.
Polar Candela Distribution
Illuminance at a Distance
180° -90°
-45°
approx. 90 cd max.
45°
Cover
L59
R = round cover S = square cover
Beam Width
0.5’
362.00
1.1’
1.2’
1.0’
90.50
2.3’
2.3’
1.5’
40.22
3.4’
3.4’
2.0’
22.62
4.5’
4.6’
2.5’
14.48
5.7’
5.7’
3.0’
10.06
6.8’
6.9’
0° Spread: 97.2°
0°
Code
Center Beam FC
90°
90° Spread: 97.6°
Wattage
Color
Beam
4
W30S
120
4 = 3.7W
W30S = 3000K, std CRI
120 = 120° beam
Finish -
MA MA = matte clear anodized
NOTE: Standard CRI has a value of 75~82.
94 95
Image shows L62-3W30S120-MA
L62
www.mplighting.com
Cabinet Fixtures
L62 3.2W Recessed Puck Light Application Showcases, kitchen cabinets, restaurant millwork, or wine cellars. Source 3.2W, 350mA LED Driver Remote 120V primary, 350mA driver (not included). LED Input Voltage 9.3V DC Power Consumption 4W Dimming 0~10V dimming with remote dimmable driver (not included). See page 186190 for Recommended Driver Chart. Weight 0.072lbs (0.032kg).
integral friction fit spring for easy mounting
Material Anodized aluminum. RoHS compliant. Mounting Recessed mount to millwork with friction fit spring clip. Comes with 6’ (1829mm) wire lead. Optimal spacing is 18” - 24” (457mm - 610mm).
1/8” 3mm
Ø2-1/2” Ø64mm
1/2” 13mm
Cutout Size Ø2-1/2” (Ø64mm) Approval Dry locations. Approved to US and Canadian standards by CSA.
Ø3” Ø76mm
20 See page 192 for explanation of symbols and IP ratings.
L62 120° 3000K Std 310 lm
Polar Candela Distribution
Illuminance at a Distance
180° -90°
Lumen test results provided by LED chip manufacturer.
-45°
approx. 100 cd max.
45°
L62
-
418.67
1.5’
1.6’
1.0’
104.67
3.1’
3.2’
1.5’
46.67
4.6’
4.8’
2.0’
26.17
6.1’
6.3’
2.5’
16.75
7.7’
7.9’
3.0’
11.63
9.2’
9.5’
Wattage
Color
Beam
3
W30S
120
3 = 3.2W
W30S = 3000K, std CRI
Beam Width
0.5’
0° Spread: 113.9°
0°
Code
Center Beam FC
90°
120 = 120° beam
90° Spread: 115.5°
Finish MA = matte clear anodized S3 = stainless steel 303
NOTE: Standard CRI has a value of 75~82.
96 97
Image shows L64-2W30S120NA-MA
L64
www.mplighting.com
Shown as 12° & 30° beam
Cabinet Fixtures
L64 2.5W Surface Mount Puck Light 1-3/4” 45mm
Application Showcases, kitchen cabinets, restaurant millwork, or wine cellars. Source 2.5W, 700mA LED
Shown as 12° beam with half shroud (HS).
Driver Remote 120V or 277V primary, 700mA driver (not included). Ø3” Ø76mm
LED Input Voltage 4V DC
7/8” 22mm
Power Consumption 3W Dimming 0~10V dimming with remote dimmable driver (not included). See page 186-190 for Recommended Driver Chart.
1-1/4” 32mm
Ø1” Ø26mm
Ø7/8” Ø22mm
3/8” 10mm
Weight 0.17lbs (0.079kg). Material Anodized aluminum. RoHS compliant. 1-3/4” 45mm
Mounting Surface mount to cabinet millwork. Comes with 6’ (1829mm) wire lead.
NA
HS
FS
Approval Dry locations. Approved to US and Canadian standards by CSA. Shown as 120° beam
Ø3” Ø76mm
40
1/2” 13mm
See page 192 for explanation of symbols and IP ratings.
1” 26mm
1/2” 13mm
NA
L64 120°, NA 3000K Std 190 lm
Polar Candela Distribution
FS
Illuminance at a Distance
180° -90°
Lumen test results provided by LED chip manufacturer.
-45°
Code -
Center Beam FC
90°
approx. 75 cd max.
45°
0°
L64
HS
Ø1” Ø26mm
Color
2
W30S
2 = 2.5W
72.45
2.3’
2.3’
2.0’
18.11
4.6’
4.5’
3.0’
8.05
6.8’
6.8’
4.0’
4.53
9.1’
9.0’
5.0’
2.90
6.0’
2.01
0° Spread: 97.4°
Wattage
W30S = 3000K, std CRI
Beam Width
1.0’
11.4’ 11.3’ 13.7’ 13.5’ 90° Spread: 96.8°
Beam
Accessories
Finish -
12 = 12° beam 30 = 30° beam 120 = 120° beam
NA = no accessory HS = half shroud FS = full shroud
MA = matte clear anodized WH = white BA = black anodized
NOTE: Standard CRI has a value of 75~82.
98 99
Image shows L65-2W30S12NA-MA
L65
www.mplighting.com
Shown as 12° & 30° beam
Cabinet Fixtures
L65 2.5W Recessed Mount Puck Light Application Showcases, kitchen cabinets, restaurant millwork, or wine cellars. Source 2.5W, 700mA LED
integral friction fit spring for easy mounting
Driver Remote 120V or 277V primary, 700mA driver (not included).
Ø2-3/8” Ø60mm
7/8” 22mm
LED Input Voltage 4V DC
Shown as 12° beam with half shroud (HS).
1/2” 13mm
Power Consumption 3W Dimming 0~10V dimming with remote dimmable driver (not included). See page 186-190 for Recommended Driver Chart.
1-1/4” 32mm
1” 26mm
Ø3” Ø76mm
Ø7/8” Ø22mm
3/8” 10mm
Weight 0.28lbs (0.125kg). Material Anodized aluminum. RoHS compliant. Mounting Recessed mount to cabinet millwork. Comes with 6’ (1829mm) wire lead.
NA
Cutout Size Ø2-1/2” (Ø64mm) Shown as 120° beam
Approval Dry locations. Approved to US and Canadian standards by CSA.
Ø2-3/8” Ø60mm
HS
FS
integral friction fit spring for easy mounting 1/2” 13mm
40 See page 192 for explanation of symbols and IP ratings.
1/2” 13mm
Ø3” Ø76mm
NA
L65 30°, HS 3000K Std 190 lm
Polar Candela Distribution
FS
Illuminance at a Distance
180° -90°
Lumen test results provided by LED chip manufacturer.
-45°
Code -
Center Beam FC
90°
approx. 600 cd max.
45°
Wattage
Color
2
W30S
2 = 2.5W
W30S = 3000K, std CRI
Beam Width
1.0’
596.88
0.5’
0.5’
2.0’
149.22
1.0’
1.0’
3.0’
66.32
1.4’
1.5’
4.0’
37.30
1.9’
2.0’
5.0’
23.88
2.4’
2.5’
6.0’
16.58
2.9’
3.0’
0° Spread: 26.9°
0°
L65
HS
Ø1” Ø26mm
90° Spread: 27.7°
Beam
Accessories
Finish -
12 = 12° beam 30 = 30° beam 120 = 120° beam
NA = no accessory HS = half shroud FS = full shroud
MA = matte clear anodized WH = white BA = black anodized
NOTE: Standard CRI has a value of 75~82.
100 101
Image shows L723CT-W30SF2D-1MA
L72
www.mplighting.com
Application Indoor directional light for wall, picture, or signage illumination. Source 12 x 1W, 350mA LEDs Driver Remote 120V primary, 700mA 12V AC or 24V DC driver (not included). LED Input Voltage 12V AC or 24V DC Power Consumption 17W Dimming Dimming available. Please consult factory. See page 186-190 for Recommended Driver Chart. Weight 0.925lbs (0.42kg). Material Anodized aluminum. RoHS compliant.
Ø2-3/8” Ø60mm
1/4” 6mm
Canopy Mount & Rail Systems
L72 12W Spotlight
stem
Mounting C1C & C2C mount to custom 2” x 2” octagonal box (included). C1M & C2M retrofit to existing standard octagonal box using custom mounting plate (included). C3 & C4 mount to standard octagonal box (not included). Can mount to 12V AC or 24V DC MP Lighting SR, DC, and SF rail systems as well as the MP Lighting 3-Circuit Track (sold separately). See pages 160-167 for rail system hardware and pages 171-174 for 3CT hardware.
5-3/4” 146mm max. 4-1/8” 105mm
Approval Dry locations. Approved to US and Canadian standards by CSA. 5-1/8” 130mm
20
Shown as DC rail mount (dual circuit). See page 193 for mounting options.
See page 192 for explanation of symbols and IP ratings.
L72 30° 3000K Std 641 lm Lumen test results provided by MP Lighting integrating sphere (see page 194).
Polar Candela Distribution
Illuminance at a Distance
180° -90°
Center Beam FC
90°
-45°
approx. 2700 cd max.
45°
Code
Mount
L72
1,248.89
0.8’
0.8’
3.0’
312.22
1.7’
1.7’
4.5’
138.77
2.5’
2.5’
6.0’
78.06
3.3’
3.3’
7.5’
49.96
4.2’
4.2’
9.0’
34.69
5.0’
5.0’
0° Spread: 31.0°
0°
Beam Width
1.5’
Color
90° Spread: 31.0°
Beam
Input Voltage
C1C = Ø2-3/8” x 1/4” canopy w/ custom octagonal box C1M = Ø2-3/8” x 1/4” canopy w/ retrofit mounting plate C2C = 2-5/8” Sq. x 3/8” canopy w/ custom octagonal box C2M = 2-5/8” Sq. x 3/8” canopy w/ retrofit mounting plate C3 = Ø4-5/8” x 1/4” canopy C4 = 4-5/8” Sq. x 1/4” canopy DC = dual circuit SR = single rail SF = single rail flush wall 3CT = 3 circuit track (silver adaptor finish)
Stem -
W27S = 2700K, std CRI W30S = 3000K, std CRI W35S = 3500K, std CRI W41S = 4100K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
S = spot (12°) N = narrow flood (30°) F = flood (60°)
1A = 12V AC 2D = 24V DC
Fixture Finish MA
1 = 1” (25mm) X = custom length
MA = matte clear anodized
NOTE: Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
102 103
Image shows L73DC-W30SF2D-1MA
L73
www.mplighting.com
Canopy Mount & Rail Systems
L73 6W Spotlight Application Indoor directional light for wall, picture, or signage illumination. stem
Source 6 x 1W, 350mA LEDs Driver Remote 120V primary, 350mA 12V AC or 24V DC driver (not included). Please specify. LED Input Voltage 12V AC or 24V DC
6” 152mm max.
Power Consumption 8W Dimming Dimming available. Please consult factory. See page 186-190 for Recommended Driver Chart.
3-7/8” 98mm
3” 76mm
Weight 0.71lbs (0.321kg). Material Anodized aluminum. RoHS compliant.
Shown as SR rail mount (single rail). See page 193 for mounting options.
Mounting C1C & C2C mount to custom 2” x 2” octagonal box (included). C1M & C2M retrofit to existing standard octagonal box using custom mounting plate (included). C3 & C4 mount to standard octagonal box (not included). Can mount to 12V AC or 24V MP Lighting DC, SR and SF rail systems as well as the MP Lighting 3-Circuit Track (sold separately). Also available with 1-Circuit Track adaptor. See pages 160-167 for rail system hardware and pages 171-174 for 3CT hardware. Approval Dry locations. Approved to US and Canadian standards by CSA.
20 See page 192 for explanation of symbols and IP ratings.
L73 30° 3000K Std 334 lm Lumen test results provided by MP Lighting integrating sphere (see page 194).
Polar Candela Distribution
Illuminance at a Distance
180° -90°
-45°
approx. 1400 cd max.
45°
0°
Code
Center Beam FC
90°
Mount
Beam Width
1.5’
620.28
0.8’
0.8’
3.0’
155.07
1.7’
1.7’
4.5’
68.92
2.5’
2.5’
6.0’
38.77
3.4’
3.3’
7.5’
24.81
4.2’
4.2’
9.0’
17.23
5.1’
5.0’
0° Spread: 31.4°
90° Spread: 31.2°
Track type (1Ct only)
L73
Color
Beam
Input Voltage
C1C = Ø2-3/8” x 1/4” canopy w/ custom octagonal box C1M = Ø2-3/8” x 1/4” canopy w/ retrofit mounting plate C2C = 2-5/8” Sq. x 3/8” canopy w/ custom octagonal box C2M = 2-5/8” Sq. x 3/8” canopy w/ retrofit mounting plate C3 = Ø4-5/8” x 1/4” canopy C4 = 4-5/8” Sq. x 1/4” canopy DC = dual circuit SR = single rail SF = single rail flush wall 1CT = 1 circuit track 3CT = 3 circuit track (silver adaptor finish)
L = Lightolier H = Halo J = Juno 2 = 2-wire
Stem -
W27S = 2700K, std CRI W30S = 3000K, std CRI W35S = 3500K, std CRI W41S = 4100K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
S = spot (12°) N = narrow flood (30°) F = flood (60°)
1A = 12V AC 2D = 24V DC
Fixture Finish
Adaptor finish (1CT only)
MA 1 = 1” stem (25mm) X = custom length
MA = matte clear anodized
W = white B = black
NOTE: 1-Circuit track by others.
Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
104 105
Image shows L75C3-W30SN-1MA
L75
www.mplighting.com
Application Indoor directional light for wall, picture, or signage illumination.
Ø4-5/8” Ø117mm
Source 4 x 2.5W, 700mA LEDs
3-1/2” 89mm
Driver Remote 120V primary, 700mA driver (not included).
stem
1/4” 6mm
LED Input Voltage 12V DC
5/8” 16mm
Power Consumption 12W Dimming 0~10V dimming with remote dimmable driver and controller (not included). See page 186-190 for Recommended Driver Chart.
4-5/8” 117mm max.
6” 152mm
Weight 0.57lbs (0.258kg). Material Anodized aluminum. RoHS compliant.
3” 76mm
Canopy Mount & Rail Systems
L75 10W Spotlight
Shown as C3 canopy mount. See page 193 for mounting options.
Mounting C1C & C2C mount to custom 2” x 2” octagonal box (included). C1M & C2M retrofit to existing standard octagonal box using custom mounting plate (included). C3 & C4 mount to standard octagonal box (not included). Can mount to 24V MP Lighting DC and SR rail systems as well as the MP Lighting 3-Circuit Track (sold separately). See pages 160-167 for rail system hardware and pages 171-174 for 3CT hardware. Approval Dry locations. Approved to US and Canadian standards by CSA.
20 See page 192 for explanation of symbols and IP ratings.
L75 30° 3000K Std 648 lm
Polar Candela Distribution
Illuminance at a Distance
180° -90°
Center Beam FC
90°
-45°
approx. 1800 cd max.
45°
L75 60° 3000K Std 648 lm
Lumen test results provided by LED chip manufacturer.
Polar Candela Distribution
0.8’
0.8’
3.0’
198.44
1.7’
1.7’
4.5’
88.20
2.5’
2.5’
6.0’
49.61
3.3’
3.4’
7.5’
31.75
4.1’
4.2’
9.0’
22.05
5.0’
5.1’
90° Spread: 31.4°
Illuminance at a Distance
180° -90°
Center Beam FC
90°
-45°
approx. 600 cd max.
45°
Mount
L75
Beam Width
1.5’
265.80
1.5’
1.7’
3.0’
66.45
2.9’
3.5’
4.5’
29.53
4.4’
5.2’
6.0’
16.61
5.9’
7.0’
7.5’
10.63
7.3’
8.7’
9.0’
7.38
8.8’
10.5’
0° Spread: 52.1°
0°
Code
793.77
0° Spread: 30.9°
0°
Beam Width
1.5’
Color
90° Spread: 60.4°
Beam
C1C = Ø2-3/8” x 1/4” canopy w/ custom octagonal box C1M = Ø2-3/8” x 1/4” canopy w/ retrofit mounting plate C2C = 2-5/8” Sq. x 3/8” canopy w/ custom octagonal box C2M = 2-5/8” Sq. x 3/8” canopy w/ retrofit mounting plate C3 = Ø4-5/8” x 1/4” canopy C4 = 4-5/8” Sq. x 1/4” canopy DC = dual circuit SR = single rail 3CT = 3 circuit track (silver adaptor finish)
Stem -
W30S = 3000K, std CRI W20H = 2000K, high CRI
S = spot (12°) N = narrow flood (30°) F = flood (60°)
Fixture Finish MA
1 = 1” (25mm) X = custom length
MA = matte clear anodized
NOTE: Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
106 107
Image shows L76DC-W30SN2D-1MA
L76
www.mplighting.com
Canopy Mount & Rail Systems
L76 6W Spotlight Application Indoor directional light for wall, picture, or signage illumination. Source 6 x 1W, 350mA LEDs stem
Driver Remote 120V primary, 350mA 12V AC or 24V DC driver (not included). LED Input Voltage 12V AC or 24V DC
5/8” 16mm
Power Consumption 8W Dimming Dimming available. Please consult factory. See page 186-190 for Recommended Driver Chart.
8” 203mm
Weight 0.57lbs (0.258kg). Material Anodized aluminum. RoHS compliant.
4-5/8” 117mm max.
3” 76mm
Shown as DC rail mount (dual circuit). See page 193 for mounting options.
Mounting C1C & C2C mount to custom 2” x 2” octagonal box (included). C1M & C2M retrofit to existing standard octagonal box using custom mounting plate (included). C3 & C4 mount to standard octagonal box (not included). Can mount to 12V AC or 24V DC MP Lighting DC, SR and SF rail systems as well as the MP Lighting 3-Circuit Track (sold separately). Also available with 1-Circuit Track adaptor. See pages 160-167 for rail system hardware and pages 171-174 for 3CT hardware. Approval Dry locations. Approved to US and Canadian standards by CSA.
20 See page 192 for explanation of symbols and IP ratings.
L76 30° 3000K Std 435 lm
Polar Candela Distribution
Illuminance at a Distance
180° -90°
-45°
approx. 1400 cd max.
45°
Lumen test results provided by MP Lighting integrating sphere (see page 194).
Polar Candela Distribution
623.81
0.8’
0.8’
3.0’
155.95
1.7’
1.7’
4.5’
69.31
2.5’
2.5’
6.0’
38.99
3.3’
3.3’
7.5’
24.95
4.2’
4.2’
9.0’
17.33
5.0’
5.0’
90° Spread: 31.1°
Illuminance at a Distance
180° -90°
Center Beam FC
90°
-45°
approx. 470 cd max.
45°
0°
Code
Beam Width
1.5’
0° Spread: 31.1°
0°
L76 60° 3000K Std 403 lm
Center Beam FC
90°
Mount
Beam Width
1.5’
201.86
1.7’
1.8’
3.0’
50.46
3.3’
3.5’
4.5’
22.43
5.0’
5.3’
6.0’
12.62
6.6’
7.1’
7.5’
8.07
8.3’
8.8’
9.0’
5.61
9.9’
10.6’
0° Spread: 57.8°
90° Spread: 61.0°
Track type (1Ct only)
L76
Color
Beam
Input Voltage
C1C = Ø2-3/8” x 1/4” canopy w/ custom octagonal box C1M = Ø2-3/8” x 1/4” canopy w/ retrofit mounting plate C2C = 2-5/8” Sq. x 3/8” canopy w/ custom octagonal box C2M = 2-5/8” Sq. x 3/8” canopy w/ retrofit mounting plate C3 = Ø4-5/8” x 1/4” canopy C4 = 4-5/8” Sq. x 1/4” canopy DC = dual circuit SR = single rail SF = single rail flush wall 1CT = 1 circuit track 3CT = 3 circuit track (silver adaptor finish)
L = Lightolier H = Halo J = Juno 2 = 2-wire
Stem -
W27S = 2700K, std CRI W30S = 3000K, std CRI W35S = 3500K, std CRI W41S = 4100K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
S = spot (12°) N = narrow flood (30°) F = flood (60°)
1A = 12V AC 2D = 24V DC
Fixture Finish
Adaptor finish (1CT only)
MA 1 = 1” stem (25mm) X = custom length
MA = matte clear anodized
W = white B = black
NOTE: 1-Circuit track by others.
Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
108 109
Image shows L221C3-4W30SS2NA-M
L221
www.mplighting.com
Canopy Mount & Rail Systems
Ø4-5/8” Ø117mm
L221 4W / 10W Spotlight
3-1/2” 89mm
Application Indoor directional light for wall, picture, or signage illumination. Source 4 x 1W, 350mA or 4 x 2.5W, 700mA LEDs 1/4” 6mm
Driver Remote 120V primary, 350mA (4W) or 700mA (10W) driver (not included).
stem
LED Input Voltage 12V DC
3-1/4” 83mm
Power Consumption 6W /12W Dimming 0~10V dimming with remote dimmable driver and controller (not included). See page 186-190 for Recommended Driver Chart.
3-5/8” 92mm
Weight 0.77lbs (0.351kg).
Ø2-1/4” Ø57mm
Shown as C3 canopy mount with no accessory (NA). See page 193 for mounting options.
Material Anodized aluminum. RoHS compliant. Mounting C1C & C2C mount to custom 2” x 2” octagonal box (included). C1M & C2M retrofit to existing standard octagonal box using custom mounting plate (included). C3 & C4 mount to standard octagonal box (not included). Can mount to 12V MP Lighting DC and SR rail systems as well as the MP Lighting 3-Circuit Track (sold separately). Also available with 1-Circuit Track adaptor. See pages 160-167 for rail system hardware and pages 171174 for 3CT hardware. Accessories Multiple accessories can be selected, up to two lenses and a shroud (sold separately). See page 175 for details. Approval Dry locations. Approved to US and Canadian standards by CSA. CAUTION Using a traditional low voltage 12V transformer to power the system will not work and will damage LEDs.
20 See page 192 for explanation of symbols and IP ratings.
L221 4 x 1W, 20° 3000K Std 340 lm Lumen test results provided by MP Lighting integrating sphere (see page 194).
Polar Candela Distribution
Illuminance at a Distance
180° -90°
-45°
approx. 1100 cd max.
45°
0°
Code
Center Beam FC
90°
Mount
Beam Width
1.5’
368.97
0.8’
0.8’
3.0’
92.24
1.5’
1.6’
4.5’
41.00
2.3’
2.4’
6.0’
23.06
3.1’
3.2’
7.5’
14.76
3.9’
4.0’
9.0’
10.25
4.6’
4.8’
0° Spread: 29.0°
Track type (1C only)
L221
90° Spread: 29.8°
Wattage
Color
Beam
Stem
C1C = Ø2-3/8” x 1/4” canopy w/ custom octagonal box C1M = Ø2-3/8” x 1/4” canopy w/ retrofit mounting plate C2C = 2-5/8” Sq. x 3/8” canopy w/ custom octagonal box C2M = 2-5/8” Sq. x 3/8” canopy w/ retrofit mounting plate C3 = Ø4-5/8” x 1/4” canopy C4 = 4-5/8” Sq. x 1/4” canopy DC = dual circuit SR = single rail 1C = 1 circuit track (4W only) 3CT = 3 circuit track (silver adaptor finish)
L = Lightolier H = Halo J = Juno 2 = 2-wire
Fixture Finish
Access0ries** -
4 = 4W W27S = 2700K, 1 = 10W* std CRI W30S = 3000K, std CRI W35S = 3500K, std CRI W41S = 4100K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
S = spot (20°) N = narrow flood (40°)
2 = 2” (51mm) X = custom length
NA = no accessory BE = beam elongator CS = crystal spreader MS = mistlite spreader ELB = eggcrate louver, black SH = metal shroud SHB = metal shroud, black
Adaptor finish (1c only)
M M = matte clear anodized
W = white B = black
(Custom finished available upon request. Please contact factory).
*10W only available in W30S & W20H. **Multiple accessories can be selected. Please specify. NOTE: 1-Circuit track by others.
Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
110 111
Image shows L222SR-30S2SH2D-M
L222
www.mplighting.com
Canopy Mount & Rail Systems
L222 6W Spotlight Application Indoor directional light for wall, picture, or signage illumination. stem
Source 6 x 1W, 350mA LEDs Driver Remote 120V primary, 350mA 12V AC or 24V DC driver (not included).
3-1/4” 83mm
LED Input Voltage 12V AC or 24V DC 3-5/8” 92mm
Power Consumption 8W Dimming Dimming available. Please consult factory. See page 186-190 for Recommended Driver Chart.
4-3/8” 110mm
Weight 0.77lbs (0.351kg).
Ø2-1/4” Ø57mm
Shown as SR (single rail) mount with metal shroud (SH) accessory. See page 193 for mounting options.
Material Anodized aluminum. RoHS compliant. Mounting C1C & C2C mount to custom 2” x 2” octagonal box (included). C1M & C2M retrofit to existing standard octagonal box using custom mounting plate (included). C3 & C4 mount to standard octagonal box (not included). Can mount to 12V AC or 24V DC MP Lighting DC, SR and SF rail systems as well as the MP Lighting 3-Circuit Track (sold separately). Also available with 1-Circuit Track adaptor. See pages 160-167 for rail system hardware and pages 171-174 for 3CT hardware. Accessories Multiple accessories can be selected, up to two lenses and a shroud (sold separately). See page 175 for details. Approval Dry locations. Approved to US and Canadian standards by CSA.
20 See page 192 for explanation of symbols and IP ratings.
L222 25° 3000K Std 299 lm Lumen test results provided by MP Lighting integrating sphere (see page 194).
Polar Candela Distribution
Illuminance at a Distance
180° -90°
-45°
approx. 900 cd max.
45°
0°
Code
Center Beam FC
90°
Mount
Beam Width
1.5’
411.79
0.9’
09’
3.0’
102.95
1.9’
1.9’
4.5’
45.75
2.8’
2.8’
6.0’
25.74
3.7’
3.7’
7.5’
16.47
4.7’
4.6’
9.0’
11.44
5.6’
5.6’
0° Spread: 34.5°
Track type (1C only)
L222
90° Spread: 34.4°
Color
Stem
Accessories*
C1C = Ø2-3/8” x 1/4” canopy w/ custom octagonal box C1M = Ø2-3/8” x 1/4” canopy w/ retrofit mounting plate C2C = 2-5/8” Sq. x 3/8” canopy w/ custom octagonal box C2M = 2-5/8” Sq. x 3/8” canopy w/ retrofit mounting plate C3 = Ø4-5/8” x 1/4” canopy C4 = 4-5/8” Sq. x 1/4” canopy DC = dual circuit SR = single rail SF = single rail flush wall 1C = 1 circuit track 3CT = 3 circuit track (silver adaptor finish)
L = Lightolier H = Halo J = Juno 2 = 2-wire
Fixture Finish
Input Voltage -
27S = 2700K, std CRI 30S = 3000K, std CRI 35S = 3500K, std CRI 41S = 4100K, std CRI 20H = 2000K, high CRI 30H = 3000K, high CRI
2 = 2” stem (51mm) X = custom length
NA = no accessory BE = beam elongator CS = crystal spreader MS = mistlite spreader ELB = eggcrate louver, black SH = metal shroud SHB = metal shroud, black
1A = 12V AC 2D = 24V DC
Adaptor finish (1c only)
M M = matte clear anodized
W = white B = black
(Custom finished available upon request. Please contact factory).
*Multiple accessories can be selected. Please specify. NOTE: 1-Circuit track by others.
Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
112 113
Image shows L2233CT-W30SN2SHB2D-M
L223
www.mplighting.com
Canopy Mount & Rail Systems
L223 18W Spotlight with Active Cooling System (ACS)1 Application Indoor directional light for wall, picture, or signage illumination. Source 7 x 2.5W, 700mA LEDs Driver Remote 120V primary, 700mA 12V AC or 24V DC driver (not included). LED Input Voltage 12V AC or 24V DC Power Consumption 21W Dimming Dimming available. Please consult factory. See page 186-190 for Recommended Driver Chart. Weight 1lb (0.5kg). Material Anodized aluminum. RoHS compliant. Mounting C1C & C2C mount to custom 2” x 2” octagonal box (included). C1M & C2M retrofit to existing standard octagonal box using custom mounting plate (included). C3 & C4 mount to standard octagonal box (not included). Can mount to 12V AC or 24V DC MP Lighting DC, SR and SF rail systems as well as the MP Lighting 3-Circuit Track (sold separately). See pages 160-167 for rail system hardware and pages 171-174 for 3CT hardware.
stem
Accessories Multiple accessories can be selected, up to two lenses and a shroud (sold separately). See page 175 for details.
Ø3” Ø76mm
Approval Dry locations. Approved to US and Canadian standards by CSA. Active Cooling System (ACS) detects temperature changes and control speeds of a cooling fan. Visit www.mplighting.com/support/resource for more info. Patent Application # (US): 8070324 Patent Application # (Germany): 11 2009 001 839 Patent Application # (Japan): 2011-520291
1
4-1/8” 105mm
2-3/4” 70mm
Shown as DC (dual circuit rail) mount with no accessory (NA). See page 193 for mounting options.
20 See page 192 for explanation of symbols and IP ratings.
L223 7 x 2.5W, 25° 3000K Std 591 lm Lumen test results provided by MP Lighting integrating sphere (see page 194).
Polar Candela Distribution
Illuminance at a Distance
180° -90°
Center Beam FC
90°
-45°
approx. 3800 cd max.
45°
Code
Mount
L223
C1C = Ø2-3/8” x 1/4” canopy w/ custom octagonal box C1M = Ø2-3/8” x 1/4” canopy w/ retrofit mounting plate C2C = 2-5/8” Sq. x 3/8” canopy w/ custom octagonal box C2M = 2-5/8” Sq. x 3/8” canopy w/ retrofit mounting plate C3 = Ø4-5/8” x 1/4” canopy C4 = 4-5/8” Sq. x 1/4” canopy DC = dual circuit SR = single rail SF = single rail flush wall 3CT = 3 circuit track (silver adaptor finish)
1,678.61
0.6’
0.6’
3.0’
419.65
1.2’
1.2’
4.5’
186.51
2.4’
2.4’
6.0’
104.91
3.0’
3.0’
7.5’
67.14
3.0’
3.0’
9.0’
46.63
3.6’
3.6’
0° Spread: 22.6°
0°
Beam Width
1.5’
90° Spread: 22.7°
Color
Beam
W30S
N
W30S = 3000K, std CRI
N = narrow flood (25°)
NOTE: Standard CRI has a value of 75~82.
Stem
Accessories*
Fixture Finish
Input Voltage -
2 = 2” stem (51mm) X = custom length
NA = no accessory BE = beam elongator CS = crystal spreader MS = mistlite spreader ELB = eggcrate louver, black SH = metal shroud SHB = metal shroud, black
1A = 12V AC 2D = 24V DC
M M = matte clear anodized (Custom finished available upon request. Please contact factory).
*Multiple accessories can be selected. Please specify.
114 115
Image shows L81CB-1W30SN-C10MC
1/4” 6mm
Ø1-1/2” Ø38mm
1/4” 6mm 2-5/8” 67mm
Ø1-1/2” Ø38mm
J-box (not included)
L81 1W / 2.5W Picture Light
1” 25mm
Application Indoor picture or millwork illumination. Source 1W, 350mA or 2.5W, 700mA LED
Surface level
Driver Remote 120V or 277V primary, 350mA (1W) or 700mA (2.5W) driver (not included).
Power Consumption 1.5W / 3W
Material Plated brass. RoHS compliant. Mounting Ceiling or wall mount to custom 2” x 2” octagonal box (CB) (included) or retrofit to existing standard octagonal box using custom mounting plate (MP) (included).
3-1/4” 83mm
Approval Dry locations. Approved to US and Canadian standards by CSA.
Ø2-3/8” Ø60mm
40
Polar Candela Distribution
10” 254mm
10” 254mm
180°
Center Beam FC
90°
45°
2,632.25
0.2’
0.2’
0.7’
658.06
0.3’
0.3’
1.0’
292.47
0.5’
0.5’
1.3’
164.52
0.6’
0.7’
1.7’
105.29
0.8’
0.8’
2.0’
73.12
0.9’
1.0’
0° Spread: 25.5°
Polar Candela Distribution
Beam Width
0.3’
5/8” 16mm
10” 254mm
90° Spread: 27.5°
Illuminance at a Distance
180° -90°
Center Beam FC
90°
-45°
45°
approx. 550 cd max.
5,017
0.2’
0.2’
0.7’
1,254
0.3’
0.3’
1.0’
557.42
0.5’
0.5’
1.3’
313.55
0.6’
0.7’
1.7’
200.67
0.8’
0.8’
2.0’
139.35
0.9’
1.0’
0° Spread: 25.5°
Mount
L81
Beam Width
0.3’
0°
Code
Surface level
3-1/4” 83mm
Illuminance at a Distance
0°
Lumen test results provided by LED chip manufacturer.
Ø1-1/2” 5/8” Ø38mm 16mm
3-1/4” 83mm Shown as MP mount, 120° beam, C10” (254mm) curved stem. 5/8” See page 193 for mounting options. 16mm
See page 192 for explanation of symbols and IP ratings.
approx. 300 cd max.
Ø38mm
1/4” 6mm
Ø2-3/8” Ø2-3/8” Ø60mm Ø60mm
-45°
1” 25mm Ø1-1/2”
Stem Ø2-3/8” Shown as CB mount, 12° or 30° beam, S5” (127mm) straight stem. Ø60mmJ-box See page 193 for mounting options. (not included) Ø1-1/2” 1/4” Ø38mm 6mm
Weight 0.86lbs (0.392kg) with S5 straight stem.
-90°
1” 25mm
1/4” 1-3/8” 6mm 35mm Stem
Ø2-3/8” Ø60mm
Dimming 0~10V dimming with remote dimmable driver (not included). See page 186190 for Recommended Driver Chart.
L81 2.5W, 30° 3000K Std 162 lm
Stem 2-5/8” 67mm 1-3/8” 35mm 2-5/8” 67mm
LED Input Voltage 4V DC
L81 1W, 30° 3000K Std 85 lm
1” 25mm Ø1-1/2” Ø38mm
1/4” 1-3/8” 6mm 35mm
Picture Lights
Ø2-3/8” 1” Ø60mm 25mm
L81
www.mplighting.com
Wattage
90° Spread: 27.5°
Color
Beam
CB = custom octagonal box MP = retrofit mounting plate
Stem
Finish
1 = 1W 2 = 2.5W*
W27S = 2700K, std CRI W30S = 3000K, std CRI W35S = 3500K, std CRI W41S = 4100K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
S = spot (12°) N = narrow flood (30°) W = wide flood (120°)
S5 = 5” (127mm) straight stem S10 = 10” (254mm) straight stem SX = custom straight stem C10 = 10” (254mm) curved stem CX = custom curved stem
MC = matte chrome BN = brushed nickel
*Only available in W30S & W20H. NOTE: Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
116 117
Image shows L85W2CB-W30S-C10MA
3/8” 10mm 2-5/8” 67mm J-box (not included)
3/8” 10mm
Application Indoor picture or millwork illumination.
2-3/8” Stem 60mm
2-3/8” Sq. Surface 60mm Sq. level
Source 3.5W, 350mA LED
1-1/8” 29mm
2” 51mm
Picture Lights
L85 3.5W Picture Light
2-5/8” 67mm 1/2” 13mm
2-3/8” 60mm
2-3/8” Sq. 60mm Sq. 1-3/4” 44mm
L85
www.mplighting.com
1/2” 13mm
1-1/8” 29mm
Driver Remote 120V primary, 350mA driver (not included). LED Input Voltage 12V DC
3/8”Stem 10mm
Power Consumption 4W
2-5/8” Shown as W2CB mount with 6” (152mm) straight stem. 67mm 10-1/8” See page 193 for mounting options. 257mm
Dimming 0~10V dimming with remote dimmable driver (not included). See page 186190 for Recommended Driver Chart.
J-box (not included)
Weight 0.71lbs (0.322kg) with S6 stem.
3/8” 10mm
Material Anodized aluminum. RoHS compliant. Mounting Wall mount. W1CB & W2CB mount to custom 2” x 2” octagonal box (included). W1MP & W2MP retrofit to existing standard octagonal box using custom mounting plate (included). W3 mounts to standard octagonal box (not included). Approval Dry locations. Approved to US and Canadian standards by CSA.
3-1/4” 83mm 1-3/4” 44mm
2-3/8” Sq. 60mm Sq. 3-1/4” 83mm
2-5/8” 67mm 1/2” 13mm
2” 51mm
Surface level
9-5/8” 244mm
Shown as W2MP mount with 10” (254mm) curved stem. See page 193 for mounting options. 9-5/8” 244mm 2-3/8” Sq. 60mm Sq.
40 See page 192 for explanation of symbols and IP ratings.
1/2” 13mm
7-3/4” 197mm
L85 3000K Std 122 lm
Polar Candela Distribution 180° -90°
Lumen test results provided by MP Lighting integrating sphere (see page 194).
6-7/8” 175mm
Illuminance at a Distance
Center Beam FC
90°
-45°
approx. 55 cd max.
45°
498.79
0.4’
0.9’
0.7’
124.70
0.8’
1.8’
1.0’
55.42
1.3’
2.7’
1.3’
31.17
1.7’
3.6’
1.7’
19.95
2.1’
4.5’
2.0’
13.86
2.5’
5.4’
0° Spread: 65°
0°
Beam Width
0.3’
standard vertical stem length
1/2” 13mm
2-5/8” 67mm
1-1/8” 29mm
Ø2” Ø51m
slot for hook 3/4” 19mm picture frame
90° Spread: 107.4°
Shown as wall hook WK...S6, 6” (152mm) straight stem. See page 193 for mounting options.
Code
Mount
L85
Color -
W1CB = Ø2-3/8” x 1/4” canopy w/ custom octagonal box W1MP = Ø2-3/8” x 1/4” canopy w/ retrofit mounting plate W2CB = 2-5/8” Sq. x 3/8” canopy w/ custom octagonal box W2MP = 2-5/8” Sq. x 3/8” canopy w/ retrofit mounting plate W3 = Ø4-5/8” x 1/4” canopy WK = wall hook*
W30S W30S = 3000K, std CRI
Horizontal Stem
Finish
S6 = 6” (152mm) straight stem SX = custom straight stem C10 = 10” (254mm) curved stem CX = custom curved stem
MA = matte clear anodized BA = black anodized
*Wall hook is not available in curved stem. NOTE: Standard CRI has a value of 75~82.
118 119
Image shows L202WK-6W30SF-23MA
L202
www.mplighting.com
22-7/8” 581mm
L202 6W Picture Light Application Picture or millwork illumination.
90°
Source 6 x 1W, 350mA LEDs
12-1/4” 311mm
Driver Remote 120V primary, 350mA or 24V DC driver (not included). Can also be hard-wired.
3” 76mm
R14-1/8” R359mm
LED Input Voltage 24V DC
slot for hook
Power Consumption 8W Dimming 0~10V dimming with remote dimmable driver (not included). See page 186-190 for Recommended Driver Chart.
Ø2” 51mm
3/4” 19mm
Ø2” Ø51mm
Picture Lights
3-7/8” 98mm
picture frame
Weight 0.82lbs (0.37kg). Material Anodized aluminum. RoHS compliant. Mounting Wall mount. W1CB & W2CB mount to custom 2” x 2” octagonal box (included). W1MP & W2MP retrofit to existing standard octagonal box using custom mounting plate (included). W3 mounts to standard octagonal box (not included).
Shown as wall hook (WK). See page 193 for mounting options.
stem
Approval Dry locations. Approved to US and Canadian standards by CSA. Ø2-3/8” Ø60mm
20
1/4” 6mm
See page 192 for explanation of symbols and IP ratings.
Shown as W1CB mount. See page 193 for mounting options.
L202 60° 3000K Std 510 lm
Lumen test results provided by LED chip manufacturer.
Polar Candela Distribution
Illuminance at a Distance
180° -90°
Center Beam FC
90°
-45°
approx. 470 cd max.
45°
Code
Mount
L202
1.8’
1.7’
3.0’
50.45
3.5’
3.3’
4.5’
22.42
5.3’
5.0’
6.0’
12.61
7.1’
6.6’
7.5’
8.07
8.8’
8.3’
9.0’
5.61
10.6’
10.0’
90° Spread: 57.9°
Wattage -
W1CB = Ø2-3/8” x 1/4” canopy w/ custom octagonal box W1MP = Ø2-3/8” x 1/4” canopy w/ retrofit mounting plate W2CB = 2-5/8” Sq. x 3/8” canopy w/ custom octagonal box W2MP = 2-5/8” Sq. x 3/8” canopy w/ retrofit mounting plate W3 = Ø4-5/8” x 1/4” canopy WK = wall hook
201.81
0° Spread: 60.9°
0°
Beam Width
1.5’
Color
6 6 = 6 x 1W
Beam F
W27S = 2700K, std CRI W30S = 3000K, std CRI W35S = 3500K, std CRI W41S = 4100K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
F = flood (60°)
Stem -
Finish MA
23 = 23” (584mm) X = custom stem
MA = matte clear anodized
NOTE: Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
120 121
Image shows L96DC-W30SN2D-S6M
L96
www.mplighting.com
Pendants
L96 6W Pendant Application Indoor pendant downlight illumination. Source 6 x 1W, 350mA LEDs stem/ cord
Driver Remote 120V primary, 350mA 12V AC or 24V DC driver (not included). LED Input Voltage 12V AC or 24V DC Power Consumption 8W Dimming Dimming available. Please consult factory. See page 186-190 for Recommended Driver Chart.
6-3/8” 162mm
Weight 1.81lbs (0.821kg). Material Anodized aluminum. RoHS compliant. Mounting C1C & C2C mount to custom 2” x 2” octagonal box (included). C1M & C2M retrofit to existing standard octagonal box using custom mounting plate (included). C3 & C4 mount to standard octagonal box (not included). Can mount to 12V AC or 24V DC MP Lighting DC and SR rail systems as well as the MP Lighting 3-Circuit Track (sold separately). Also available with 1-Circuit Track adaptor. See pages 160-167 for rail system hardware.
Ø3” Ø76mm
Shown as DC rail mount (dual circuit). See page 193 for mounting options.
Approval Dry locations. Approved to US and Canadian standards by CSA.
See page 192 for explanation of symbols.
L96 25° 3000K Std 254 lm Lumen test results provided by MP Lighting integrating sphere (see page 194).
Polar Candela Distribution
Illuminance at a Distance
180° -90°
-45°
approx. 2200 cd max.
45°
0°
Code
Center Beam FC
90°
Mount
Beam Width
1.5’
965.19
0.5’
0.5’
3.0’
241.30
1.1’
1.1’
4.5’
107.24
1.6’
1.6’
6.0’
60.32
2.2’
2.2’
7.5’
38.61
2.7’
2.7’
9.0’
26.81
3.3’
3.3’
0° Spread: 20.5°
Track type (1Ct only)
L96
90° Spread: 20.7°
Color -
C1C = Ø2-3/8” x 1/4” canopy w/ custom octagonal box C1M = Ø2-3/8” x 1/4” canopy w/ retrofit mounting plate C2C = 2-5/8” Sq. x 3/8” canopy w/ custom octagonal box C2M = 2-5/8” Sq. x 3/8” canopy w/ retrofit mounting plate C3 = Ø4-5/8” x 1/4” canopy C4 = 4-5/8” Sq. x 1/4” canopy DC = dual circuit SR = single rail 1C = 1 circuit track 3CT = 3 circuit track (silver adaptor finish)
L = Lightolier H = Halo J = Juno 2 = 2-wire
Beam
Input Voltage
N W27S = 2700K, std CRI N = narrow W30S = 3000K, std CRI flood W35S = 3500K, std CRI (25°) W41S = 4100K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
Stem/Cord
Fixture Finish
Adaptor finish (1CT only)
1A = 12V AC 2D = 24V DC
S6 = 6” (152mm) M = matte clear stem anodized SX = custom stem B = black C72 = 72” (1829mm) anodized coaxial cord CX = custom cord
W = white B = black
NOTE: 1-Circuit track by others.
Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
122 123
Image shows L191C1C-4W30S-C72MA
L191
www.mplighting.com
Ø2-3/8” Ø60mm
1-3/4” 44mm
Pendants
1/4” 6mm
L191 LED Pendant Application Indoor pendant. Source 0.07W, 700mA LEDs
stem/ cord
Driver Remote 120V primary, 700mA driver (not included). LED Input Voltage 24V DC Power Consumption 2’ = 9W 4’ = 17W Dimming 0~10V dimming with remote dimmable driver (not included). See page 186190 for Recommended Driver Chart. Length
Weight 1.6lbs (0.74kg). Material PMMA. Mounting C1C & C2C mount to custom 2” x 2” octagonal box (included). C1M & C2M retrofit to existing standard octagonal box using custom mounting plate (included). C3 & C4 mount to standard octagonal box (not included). Approval Dry locations. Approved to US and Canadian standards by CSA. CAUTION Using a traditional low voltage 12V transformer to power the system will not work and will damage LEDs.
Ø2” Ø51mm
Shown as C1C mount. See page 193 for mounting options.
See page 192 for explanation of symbols.
L191 2’ Length 3000K Std 1472 lm
Lumen test results provided by LED chip manufacturer.
Polar Candela Distribution
Illuminance at a Distance
180° -90°
Center Beam FC
90°
-45°
approx. 220 cd max.
45°
Code
Mount
L191
1.54
1.7’
3.0’
0.38
3.4’
9.6’
4.5’
0.17
5.0’
14.4’
6.0’
0.10
6.7’
19.2’
7.5’
0.06
8.3’
23.9’
9.0’
0.04
10.0’
28.7’
0° Spread: 58.0°
0°
Beam Width
1.5’
Length
4.8’
90° Spread: 115.9°
Color
C1C = Ø2-3/8” x 1/4” canopy w/ custom octagonal box C1M = Ø2-3/8” x 1/4” canopy w/ retrofit mounting plate C2C = 2-5/8” Sq. x 3/8” canopy w/ custom octagonal box C2M = 2-5/8” Sq. x 3/8” canopy w/ retrofit mounting plate C3 = Ø4-5/8” x 1/4” canopy C4 = 4-5/8” Sq. x 1/4” canopy
Stem/Cord
Canopy Finish
S6 = 6” (152mm) stem SX = custom stem C72 = 72” (1829mm) cord CX = custom cord
MA = matte clear anodized BN = brushed nickel
2 = 2’ (320 LEDs) 4 = 4’ (640 LEDs)
W27S = 2700K, std CRI W30S = 3000K, std CRI
NOTE: Standard CRI has a value of 75~82.
124 125
Image shows G02LC9-6W30SLC72-MC
G02L
www.mplighting.com
Ø4-13/16” Ø122mm
Pendants
11/16” 18mm
G02L 6W Glass Pendant
11/16” 18mm
Application Indoor pendant. Glass Cylinder shaped opalescent cased hand blown glass.
stem/cord
Source 6 x 1W, 350mA LEDs Driver Remote 120V primary, 350mA constant current or 24V DC constant voltage driver (not included). LED Input Voltage 24V DC Power Consumption 8W
13-3/4” 349mm
Dimming Canopy mount only. Dimmable with remote 24V constant voltage driver and dimming controller, 0~10V dimming (not included). See page 186-190 for Recommended Driver Chart.
21-5/8” 549mm
Mounting Material Anodized aluminum. Mounting C9 canopy mounts to standard octagonal box (not included). Can also mount to MP Lighting 3-Circuit Track system (sold separately). See pages 171-174 for 3CT hardware. Field adjustable 72” (1829mm) Ø1/4” (Ø6mm) clear cord. Or 6” (152mm) rigid stem. Longer lengths available, please specify.
6-1/2” 165mm
Approval Dry locations. Approved to US and Canadian standards by CSA.
Ø4-3/4” Ø121mm
Ø2-1/8” Ø54mm
See page 192 for explanation of symbols.
Shown as C9 canopy mount. See page 193 for mounting options.
G02L 3000K Std 510 lm
Polar Candela Distribution
-90°
Lumen test results provided by LED chip manufacturer.
Illuminance at a Distance
180°
Center Beam FC
90°
-45°
approx. 190 cd max.
45°
186.83
0.3’
0.3’
2.0’
46.71
0.5’
0.5’
3.0’
20.76
0.8’
0.8’
4.0’
11.68
1.0’
1.0’
5.0’
7.47
1.3’
1.3’
6.0’
5.19
1.6’
1.5’
0° Spread: 14.8°
0°
Beam Width
1.0’
90° Spread: 14.6°
Coefficients Of Utilization Effective Floor Cavity Reflectance: 20%
RCC %:
Code G02L
80
70
RW %: 70 50 30 0 70 50 RCR: 0 .29 .29 .29 .29 .27 .27 1 .25 .24 .22 .21 .23 .22 2 .23Mount .20 .18 .16 .21 .18 3 .20 .17 .15 .13 .19 .16 4 .19 .15 .13 .11 .17 .14 5 .17 .14 .11 .10 .16 .13 6 .16 .12 .10 .08 .15 .12 7 .15 .11 .09 .07 .14 .11 C9 = Ø4-13/16” 11/16” 8 .14 .10 x.08 .07 canopy .13 .10 9 .13 .10 .08 .06 .12 .09 3CT = 3-circuit track 10 .12adaptor .09 .07finish) .06 .11 .08 (silver
50 30 .27 .20 .17 .14 .12 .11 .09 .08 .08 .07 .07
0 50 30 .14 .23 .23 .10 .18 .17 .08 .15 .14 Wattage .06 .13 .12 .05 .12 .10 .05 6 .11 .09 .04 .10 .08 .04 .09 .07 6.04= 6.08x 1W .07 .03 .08 .06 .03 .07 .06
30
10
20 50 30 20 50 30 20 .23 .19 .19 .19 .16 .16 .16 .16 .15 .14 .14 .12 .12 .11 .13 .13 .12 Color .11 .10 .09 .09 .10 .11 .10 .09 .09 .08 .07 .09 .10 .09 .07 .08 .07 .06 .08 .09 .08 .06 .07 .06 .05 .07 .08 .07 .06 .07 .06 .05 .06 .08 .06 .05 .06 .05 .04 W27S = std .05 CRI .04 .06 .07 .062700K, .05 .06 .05 .07 .053000K, .04 .05 W30S = std .04 CRI .04 .05 .06 .05 .04 .05 .04 .04
W35S = 3500K, std CRI W41S = 4100K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
0 0 .14 .10 .07 .06 .05 .04 .04 .04 L= .03 .03 .03
Glass Size
Stem/Cord
L 21-5/8”H (549mm)
Mounting Finish -
S6 = 6” (152mm) stem SX = custom stem C72 = 72” (1829mm) cord CX = custom cord
MC = matte chrome BA = black anodized BN = brushed nickel
NOTE: Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
126 127
Image shows G03LC9-6W30SLC72-MC
G03L
www.mplighting.com
Ø4-13/16” Ø122mm
11/16” 18mm
Application Indoor pendant.
Pendants
G03L 6W Glass Pendant
11/16” 18mm stem/cord
Glass Open top and bottom, cylinder shaped hand blown opalescent cased glass. Source 6 x 1W, 350mA LEDs Driver Remote 120V primary, 350mA constant current or 24V DC constant voltage driver (not included). LED Input Voltage 24V DC Power Consumption 8W 15-3/4” 400mm
Dimming Canopy mount only. Dimmable with remote 24V constant voltage driver and dimming controller, 0~10V dimming (not included). See page 186-190 for Recommended Driver Chart.
23-5/8” 600mm
Mounting Material Anodized aluminum. Mounting C9 canopy mounts to standard octagonal box (not included). Can also mount to MP Lighting 3-Circuit Track system (sold separately). See pages 171-174 for 3CT hardware. Field adjustable 72” (1829mm) Ø1/4” (Ø6mm) clear cord. Or 6” (152mm) rigid stem. Longer lengths available, please specify. 6-1/2” 165mm
Approval Dry locations. Approved to US and Canadian standards by CSA.
Ø2-1/8” Ø54mm
See page 192 for explanation of symbols.
Ø3-15/16” Ø100mm
Shown as C9 canopy mount. See page 193 for mounting options.
G03L 3000K Std 510 lm
Polar Candela Distribution
-90°
Lumen test results provided by LED chip manufacturer.
Illuminance at a Distance
180°
Center Beam FC
90°
-45°
approx. 190 cd max.
45°
183.64
0.2’
0.2’
2.0’
45.91
0.4’
0.5’
3.0’
20.40
0.7’
0.7’
4.0’
11.48
0.9’
1.0’
5.0’
7.35
1.1’
1.2’
6.0’
5.10
1.3’
1.5’
0° Spread: 12.5°
0°
Beam Width
1.0’
90° Spread: 14.1°
Coefficients Of Utilization Effective Floor Cavity Reflectance: 20%
RCC %:
Code G03L
80
70
RW %: 70 50 30 0 70 50 RCR: 0 .55 .55 .55 .55 .51 .51 1 .47 .44 .41 .38 .43 .41 2 .42Mount .37 .33 .30 .39 .34 3 .38 .32 .27 .24 .35 .29 4 .35 .28 .23 .20 .31 .26 5 .32 .25 .20 .17 .29 .23 6 .29 .22 .18 .14 .27 .20 7 .27 .20 .16 .12 .25 .18 C9 = Ø4-13/16” 11/16” 8 .25 .18 x.14 .11 canopy .23 .17 9 .23 .17 .13 .10 .21 .15 3CT = 3-circuit track 10 .22adaptor .15 .11finish) .09 .20 .14 (silver
50 30 .51 .38 .30 .25 .21 .19 .16 .14 .13 .12 .11
0 50 30 .27 .43 .43 .18 .34 .32 .13 .28 .26 Wattage .10 .24 .21 .09 .21 .18 .07 6 .19 .16 .06 .17 .14 .06 .15 .12 6.05= 6.14x 1W .11 .05 .13 .10 .04 .12 .09
30
10
20 50 30 20 50 30 20 .43 .36 .36 .36 .30 .30 .30 .30 .28 .26 .25 .22 .21 .20 .23 .23 .21 Color .19 .18 .16 .15 .18 .20 .17 .15 .15 .14 .12 .15 .17 .15 .13 .14 .12 .10 .13 .15 .13 .11 .12 .10 .08 .11 .14 .11 .09 .11 .09 .07 .10 .13 .10 .08 .10 .08 .06 W27S = std .07 CRI .06 .09 .12 .092700K, .07 .09 .08 .11 .083000K, .07 .09 W30S = std .07 CRI .05 .07 .10 .08 .06 .08 .06 .05
W35S = 3500K, std CRI W41S = 4100K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
0 0 .27 .17 .13 .10 .08 .07 .06 .05 L= .05 .04 .04
Glass Size
Stem/Cord
L 23-5/8”H (600mm)
Mounting Finish -
S6 = 6” (152mm) stem SX = custom stem C72 = 72” (1829mm) cord CX = custom cord
MC = matte chrome BA = black anodized BN = brushed nickel
NOTE: Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
128 129
Image shows P71LSR-WHW30S2D-M
P71L
www.mplighting.com
Pendants
P71L 6W Glass Pendant Application Indoor pendant. Glass Open top and bottom, cylinder shaped hand blown opalescent cased glass. Source 6 x 1W, 350mA LEDs Driver Remote 120V primary, 350mA 12V AC or 24V DC driver (not included). LED Input Voltage 12V AC or 24V DC Power Consumption 8W
17-7/8” 454mm
Dimming Please consult factory. Mounting Material Anodized aluminum. Mounting C1C & C2C mount to custom 2” x 2” octagonal box (included). C1M & C2M retrofit to existing standard octagonal box using custom mounting plate (included). C3 & C4 mount to standard octagonal box (not included). Can mount to 12V AC or 24V DC MP Lighting DC and SR rail systems as well as the MP Lighting 3-Circuit Track (sold separately). Also available with 1-Circuit Track adaptor. See pages 160-167 for rail system hardware.
Ø4-3/4” Ø121mm
Approval Dry locations. Approved to US and Canadian standards by CSA.
Shown as single rail mount. See page 193 for mounting options.
See page 192 for explanation of symbols.
P71L 3000K Std 510 lm
Polar Candela Distribution
Center Beam FC -90°
Lumen test results provided by LED chip manufacturer.
Illuminance at a Distance
180° 90°
-45°
approx. 190 cd max.
45°
0°
Code
Mount
Beam Width
1.0’
195.3
0.5’
0.5’
2.0’
48.8
1.0’
1.0’
3.0’
21.7
1.5’
1.5’
4.0’
12.2
2.0’
1.9’
5.0’
7.8
2.5’
2.4’
6.0’
5.4
3.0’
2.9’
0° Spread: 27.9°
Track type (1Ct only)
P71L
90° Spread: 27.3°
Shade
Color
C1C = Ø2-3/8” x 1/4” canopy w/ custom octagonal box C1M = Ø2-3/8” x 1/4” canopy w/ retrofit mounting plate C2C = 2-5/8” Sq. x 3/8” canopy w/ custom octagonal box C2M = 2-5/8” Sq. x 3/8” canopy w/ retrofit mounting plate C3 = Ø4-5/8” x 1/4” canopy C4 = 4-5/8” Sq. x 1/4” canopy DC = dual circuit SR = single rail 1CT = 1 circuit track 3CT = 3 circuit track (silver adaptor finish)
L = Lightolier H = Halo J = Juno 2 = 2-wire
Mounting Finish
Input Voltage
Adaptor finish (1CT only)
SP = black stripe pattern WH = white opalescent
W27S = 2700K, std CRI 1A = 12V AC W30S = 3000K, std CRI 2D = 24V DC W35S = 3500K, std CRI W41S = 4100K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
M = matte clear W = white B = black anodized B = black anodized
NOTE: 1-Circuit track by others.
Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
Standard 72" coaxial cable, field adjustable. Longer custom length available.
130 131
Image shows P81LDC-WHW30S2D-M
P81L
www.mplighting.com
Pendants
P81L 6W Glass Pendant Application Indoor pendant. Glass Open top and bottom, cylinder shaped hand blown opalescent cased glass. Source 6 x 1W, 350mA LEDs Driver Remote 120V primary, 350mA 12V AC or 24V DC driver (not included). LED Input Voltage 12V AC or 24V DC Power Consumption 8W Dimming Please consult factory.
11-1/8” 283mm
Mounting Material Anodized aluminum. Mounting C1C & C2C mount to custom 2” x 2” octagonal box (included). C1M & C2M retrofit to existing standard octagonal box using custom mounting plate (included). C3 & C4 mount to standard octagonal box (not included). Can mount to 12V AC or 24V DC MP Lighting DC and SR rail systems as well as the MP Lighting 3-Circuit Track (sold separately). Also available with 1-Circuit Track adaptor. See pages 160-167 for rail system hardware.
Ø3” Ø76mm
Approval Dry locations. Approved to US and Canadian standards by CSA.
Shown as dual circuit rail mount. See page 193 for mounting options.
See page 192 for explanation of symbols.
P81L 3000K Std 510 lm
Polar Candela Distribution
Center Beam FC -90°
Lumen test results provided by LED chip manufacturer.
Illuminance at a Distance
180° 90°
-45°
approx. 190 cd max.
45°
0°
Code
Mount
185.2
0.5’
0.5’
2.0’
46.3
0.9’
1.0’
3.0’
20.6
1.4’
1.5’
4.0’
11.6
1.9’
2.0’
5.0’
7.4
2.4’
2.5’
6.0’
5.2
2.8’
2.9’
0° Spread: 26.5°
Track type (1Ct only)
P81L L = Lightolier H = Halo J = Juno 2 = 2-wire
90° Spread: 27.6°
Shade -
C1C = Ø2-3/8” x 1/4” canopy w/ custom octagonal box C1M = Ø2-3/8” x 1/4” canopy w/ retrofit mounting plate C2C = 2-5/8” Sq. x 3/8” canopy w/ custom octagonal box C2M = 2-5/8” Sq. x 3/8” canopy w/ retrofit mounting plate C3 = Ø4-5/8” x 1/4” canopy C4 = 4-5/8” Sq. x 1/4” canopy DC = dual circuit SR = single rail 1CT = 1 circuit track 3CT = 3 circuit track (silver adaptor finish)
Beam Width
1.0’
Color
WH WH = white opalescent
Mounting Finish
Input Voltage
Adaptor finish (1CT only)
W27S = 2700K, std CRI 1A = 12V AC W30S = 3000K, std CRI 2D = 24V DC W35S = 3500K, std CRI W41S = 4100K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
M = matte clear W = white B = black anodized B = black anodized
NOTE: 1-Circuit track by others.
Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
Standard 72" coaxial cable, field adjustable. Longer custom length available.
132 133
Image shows P82LSR-ABW30S2D-M
P82L
www.mplighting.com
Pendants
P82L 6W Glass Pendant Application Indoor pendant. Glass Open top and bottom, cylinder shaped alabaster. Source 6 x 1W, 350mA LEDs Driver Remote 120V primary, 350mA 12V AC or 24V DC driver (not included). LED Input Voltage 12V AC or 24V DC Power Consumption 8W Dimming Please consult factory.
11” 279mm
Mounting Material Anodized aluminum. Mounting C1C & C2C mount to custom 2” x 2” octagonal box (included). C1M & C2M retrofit to existing standard octagonal box using custom mounting plate (included). C3 & C4 mount to standard octagonal box (not included). Can mount to 12V AC or 24V DC MP Lighting DC and SR rail systems as well as the MP Lighting 3-Circuit Track (sold separately). Also available with 1-Circuit Track adaptor. See pages 160-167 for rail system hardware.
Ø3-5/8” Ø92mm
Approval Dry locations. Approved to US and Canadian standards by CSA.
Shown as single rail mount. See page 193 for mounting options.
See page 192 for explanation of symbols.
P82L 3000K Std 510 lm
Polar Candela Distribution
Center Beam FC -90°
Lumen test results provided by LED chip manufacturer.
Illuminance at a Distance
180° 90°
-45°
approx. 190 cd max.
45°
0°
Code
Mount
185.2
0.5’
0.5’
2.0’
46.3
0.9’
1.0’
3.0’
20.6
1.4’
1.5’
4.0’
11.6
1.9’
2.0’
5.0’
7.4
2.4’
2.5’
6.0’
5.2
2.8’
2.9’
0° Spread: 26.5°
Track type (1Ct only)
P82L L = Lightolier H = Halo J = Juno 2 = 2-wire
90° Spread: 27.6°
Shade -
C1C = Ø2-3/8” x 1/4” canopy w/ custom octagonal box C1M = Ø2-3/8” x 1/4” canopy w/ retrofit mounting plate C2C = 2-5/8” Sq. x 3/8” canopy w/ custom octagonal box C2M = 2-5/8” Sq. x 3/8” canopy w/ retrofit mounting plate C3 = Ø4-5/8” x 1/4” canopy C4 = 4-5/8” Sq. x 1/4” canopy DC = dual circuit SR = single rail 1CT = 1 circuit track 3CT = 3 circuit track (silver adaptor finish)
Beam Width
1.0’
Color
AB AB = alabaster
Mounting Finish
Input Voltage
Adaptor finish (1CT only)
W27S = 2700K, std CRI 1A = 12V AC W30S = 3000K, std CRI 2D = 24V DC W35S = 3500K, std CRI W41S = 4100K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
M = matte clear W = white B = black anodized B = black anodized
NOTE: 1-Circuit track by others.
Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
Standard 72" coaxial cable, field adjustable. Longer custom length available.
134 135
Image shows L102N-XS3W20HWT-MA
L101
www.mplighting.com
Linear Systems
L101 Linear Strip Light Application Indoor linear cove, wall slot, shelf, and cabinet illumination. Source 1W, 350mA LEDs (4W/Ft or 6W/Ft) Input Current S2 = 350mA/foot. S3 = 230mA/foot. Driver Remote 120V primary, constant voltage driver (not included). LED Input Voltage 24V DC S (LED spacing)
Power Consumption S2 = 8W/foot S3 = 6W/foot Dimming 0~10V dimming with remote dimmable driver (not included). See page 186-190 for Recommended Driver Chart.
1-1/4” 32mm
Weight 0.56lb (0.25kg)/foot.
1/8” 3mm
Material Aluminum and polycarbonate. RoHS compliant.
End feed only.
L (circuit board length)
Mounting Surface mount. Includes aluminum mounting channel with wiring compartment. Comes with 3’ (914mm) wire lead. 0°
Approval Dry locations. Approved to US and Canadian standards by CSA. 1” 25mm
45 .
1-3/8” 35mm
50 See page 192 for explanation of symbols and IP ratings. Shown with 45° angle mount, Flat lens
L101 4’ Length S2 Spacing 120° Flat Frosted 3000K Std 1000 lm
Polar Candela Distribution
Convex clear lens
Illuminance at a Distance
180°
45 .
0°
4.8’
4.4’
42.42
9.5’
8.9’
4.5’
18.86
14.3’
13.3’
6.0’
10.61
19.0’
17.7’
7.5’
6.79
23.8’
22.1’
9.0’
4.71
28.5’
26.6’
1-3/8” 1.5’ 1-3/8” 35mm 3.0’ 35mm -45°
approx. 380 cd max.
45°
L101 4’ Length S3 Spacing 120° Flat Frosted 3000K Std 782 lm
Polar Candela Coefficients OfDistribution Utilization
-90° RW %:
Lumen test results provided by MP Lighting integrating sphere (see page 194).
RCR: 0 1 2 3 4 -45° 5 6 7 8 9 10
80
70 .64 .58 .53 .48 .44 .41 .38 .35 .32 .30 .28
1” 25mm
1” 25mm
1-1/4” 32mm
Shown with no angle mount, Flat lens
1-1/4” 32mm
Convex clear lens
90° Spread: 111.7°
’
Illuminance at a Distance Effective Floor Cavity Reflectance: 20%
180°
RCC %:
169.70
0° Spread: 115.5°
0°
Beam Width
0°
Center Beam FC
90°
45 .
-90°
70
50 30 .64 .64 .56 .54 .49 .45 .43 .38 .38 .33 .34 .29 .30 .26 .28 .23 .25 .21 .230° .19 .21 .17
0 70 .64 .62 .52 .57 .42 .52 .35 .47 .30 .43 .25 approx..40 .22 250 cd.37 .20 max. .34 .17 .32 .16 .29 .14 .28
90° 50
.62 .55 .48 .42 .37 45° .33 .30 .27 .25 .23 .21
50
30 .62 .53 .44 .38 .33 .29 .25 .23 .20 .18 .17
0 .53 .45 .38 .32 .28 .24 .21 .19 .17 .15 .14
50 1.5’ .60 .52 3.0’ .46 4.5’ .40 .36 6.0’ .32 7.5’ .29 .26 9.0’ .24 0° .22 .20
30 10 0 Center Beam FC Beam Width 0 30 20 50 30 20 50 30 20 4.7’ .55 4.5’ .57 .57 .57 .55 .60 .60 108.97 .55 .53 .51 .49 .50 .49 .48 .48 .47 .46 .45 27.24 9.0’ 9.3’ .43 .41 .44 .42 .40 .42 .40 .39 .37 .39 .36 .33 14.0’ .37 .34 12.11 .37 .3513.5’ .33 .32 .32 .29 .35 .31 .29 .33 .30 .28 .27 6.81 18.7’ 18.0’ .28 .25 .31 .27 .25 .30 .27 .24 .23 .28 .24 .22 23.4’ .25 .22 4.36 .27 .2422.5’ .21 .20 .25 .22 .19 28.0’ .22 .19 3.03 .25 .2127.0’ .19 .18 .20 .17 .23 .20 .17 .23 .19 .17 .16 Spread: Spread: .21 .18 .1590° .21 .18 .16114.6° .18 112.6° .15 .14 .17 .14 .20 .16 .14 .19 .16 .14 .13
Coefficients Of Utilization
Code L101
Mount RCC %: RW %: 70 RCR: 0 .61 1 .56 2 .51 N = no3angle .47 .43 A = 45°45 angle .39 6 .36 7 .33 8 .31 9 .29 10 .27
80
Length70 (L)
50 30 0 70 50 30 .61- .61 .61 .60 .60 .60 .54 .52 .50 .55 .52 .51 .47 .43 .40 .50 .46 .43 = 1’ .45 (305mm) .40 .36 .41 .371 .34 .36 .32 .28 .41 .36 .31 2 = 2’ (610mm) .33 .28 .24 .38 .32 .28 = 3’ .35 (914mm) .29 .24 .29 .253 .21 .26 .22 .19 .33 .26 .22 4 = 4’ (1219mm) .24 .20 .17 .30 .24 .20 .22 .18 .22 .188 .15 = 8’ .28 (2438mm) .20 .16 .14 .27 .20 .16
X = custom
Effective Floor Cavity Reflectance: 20%
Spacing (s) 50
10 Color0
30
50 50 30 20 0 .51 .57 .57 .57 .55 .44 .50 .49 .47 .48 .37 .44 .41 .39 .42 = 2” .35(51mm) .33 .37 .31S2 .39 .27 .34 .31 .28 .33 S3 = 3” (76mm) .23 .31 .27 .24 .30 between LEDs.27 .24 .21 .20 .28 .18 .25 .21 .19 .24 .16 .23 .19 .17 .22 .15 .21 .18 .15 .21 .13 .20 .16 .14 .19
30 20 0 50 30 20 .55 .55 .52 .52 .52 .51 .47 .46 .46 .45 .44 .43 .40 .38 .41 .39 .37 .36 W27S = 2700K, std CRI .34 .32 .36 .30 .34 .31 .30 .27 .32 .29 .27 .26 W30S = 3000K, std CRI .26 .24 .29 .26 .23 .22 W35S = 3500K, std CRI .23 .21 .26 .20 .23 .21 .21 .18 .24 .21 .18 .17 W41S = 4100K, std CRI .19 .16 .22 .19 .16 .15 .17 .15 .17 .15 .20 W20H = 2000K, high.14 CRI .16 .13 .19 .16 .13 .12
Beam
Lens
W W = wide flood (120°)
Finish -
T = flat clear F = flat frosted C = convex clear
MA MA = matte clear anodized
W30H = 3000K, high CRI NOTE: S2 = 12’ (3658mm) max. S3 = 18’ (5486mm) max
Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
136 137
Image shows L102A-XS56W30SWT-MA
L102
www.mplighting.com
Linear Systems
L102 Linear Strip Light Application Indoor linear cove, wall slot, shelf, and cabinet illumination. Source 0.07W, 20mA LEDs (1.9W/Ft or 3.9W/Ft) Input Current S28 = 80mA/foot. S56 = 160mA/foot. Driver Remote 120V primary, constant voltage driver (not included). LED Input Voltage 24V DC
S (LED spacing)
Power Consumption S28 = 2.3W/foot S56 = 4.6W/foot Dimming 0~10V dimming with remote dimmable driver (not included). See page 186-190 for Recommended Driver Chart.
1-1/4” 32mm
Weight 0.56lbs (0.25kg)/foot. 1/8” 3mm
Material Aluminum and polycarbonate. RoHS compliant.
End feed only.
L (circuit board length)
Mounting Surface mount. Includes aluminum mounting channel with wiring compartment. Comes with 3’ (914mm) wire lead.
45 .
0°
Approval Dry locations. Approved to US and Canadian standards by CSA. 1-3/8” 35mm
50 See page 192 for explanation of symbols and IP ratings. Shown with 45° angle mount, Flat lens
L102N 4’ Length S28 Spacing 120° Flat Frosted 3000K Std 285 lm
Polar Candela Distribution
Convex clear lens
Illuminance at a Distance
180° -90°
Center Beam FC
90°
-45°
approx. 100 cd max.
45°
Polar Candela Coefficients OfDistribution Utilization
-90° RW %:
Lumen test results provided by MP Lighting integrating sphere (see page 194).
RCR: 0 1 2 3 4 -45° 5 6 7 8 9 10
80
70 .73 .66 .60 .55 .50 .46 .43 .40 .37 .34 .32
4.4’
4.8’
3.0’
11.71
8.7’
9.7’
4.5’
5.20
13.1’
14.5’
6.0’
2.93
17.5’
19.4’
7.5’
1.87
21.8’
24.2’
9.0’
1.30
26.2’
29.1’
1” 1” 25mm 25mm
1-1/4” 1-1/4” 32mm 32mm
Shown with no angle mount, Flat lens
Convex clear lens
90° Spread: 116.5°
Illuminance at a Distance Effective Floor Cavity Reflectance: 20%
180°
RCC %:
46.84
0° Spread: 111.0°
0°
L102N 4’ Length S56 Spacing 120° Flat Frosted 3000K Std 565 lm
Beam Width
1.5’
70
50 30 .73 .73 .64 .61 .55 .51 .49 .44 .43 .38 .38 .33 .35 .29 .31 .26 .29 .23 .260° .21 .24 .19
0 70 .73 .71 .59 .65 .48 .59 .40 .54 .34 .49 .29 approx..45 .25 210 cd.42 .22 max. .39 .20 .36 .18 .34 .16 .31
90° 50
.71 .62 .54 .48 .42 45° .38 .34 .31 .28 .26 .24
50
30 .71 .60 .50 .43 .37 .33 .29 .26 .23 .21 .19
0 .61 .51 .43 .37 .32 .28 .24 .21 .19 .17 .16
50 1.5’ .68 .59 3.0’ .52 4.5’ .46 .41 6.0’ .36 7.5’ .33 .30 9.0’ .27 0° .25 .23
30 10 0 Center Beam FC Beam Width 0 30 20 50 30 20 50 30 20 4.4’ .62 4.9’ .65 .65 .65 .62 .68 .68 93.51 .62 .61 .57 .56 .57 .55 .54 .55 .53 .52 .51 23.38 9.7’ 8.8’ .49 .46 .50 .47 .45 .48 .46 .44 .43 .44 .41 .38 13.2’ .42 .39 10.39 .42 .4014.6’ .37 .36 .36 .33 .39 .35 .32 .38 .35 .32 .31 5.84 17.5’ 19.5’ .32 .28 .35 .31 .28 .34 .31 .28 .26 .32 .28 .25 21.9’ .28 .25 3.74 .31 .2724.3’ .24 .23 .29 .25 .22 26.3’ .25 .22 2.60 .28 .2429.2’ .22 .20 .23 .20 .26 .22 .19 .26 .22 .19 .18 Spread: Spread: .24 .20 .1790° .24 .21 .18111.3° .20 116.7° .17 .16 .19 .16 .23 .19 .16 .22 .18 .16 .15
Coefficients Of Utilization
Code L102
Mount RCC %: RW %: 70 RCR: 0 .73 1 .66 2 .60 N = no3angle .55 4 .50 A = 45° angle 5 .46 6 .43 7 .40 8 .37 9 .34 10 .32
80
Length70 (L)
50 30 0 70 50 30 .73- .73 .73 .71 .71 .71 .64 .61 .59 .65 .62 .60 .55 .51 .48 .59 .54 .50 = 1’ .54 (305mm) .48 .43 .49 .441 .40 .43 .38 .34 .49 .42 .37 2 = 2’ (610mm) .38 .33 .29 .45 .38 .33 = 3’ .42 (914mm) .34 .29 .35 .293 .25 .31 .26 .22 .39 .31 .26 4 = 4’ (1219mm) .29 .23 .20 .36 .28 .23 .26 .21 .26 .218 .18 = 8’ .34 (2438mm) .24 .19 .16 .31 .24 .19
X = custom
Effective Floor Cavity Reflectance: 20%
Spacing 50
(s) 30
0 50 30 20 50 30 .61 .68 .68 .68 .65 .65 .52 .59 .58 .56 .57 .55 .43 .52 .49 .46 .50 .47 28 .39 LEDs.44 per .41 1’ .46=.42 .37S28 .32 .41 .36 .33 .39 .35 S56 = 56 LEDs per 1’ .28 .36 .32 .28 .35 .31 .24 .33 .28 .25 .32 .28 .21 .30 .25 .22 .29 .25 .19 .27 .23 .20 .26 .22 .17 .25 .21 .18 .24 .20 .16 .23 .19 .16 .23 .19
10
Color 0
Beam
0 20 50 30 20 .65 .62 .62 .62 .61 W .54 .55 .53 .52 .51 .45 .48 .46 .44 .43 W22S = std CRI W = wide flood .38 .42 .402200K, .37 .36 .32 .38 .35 .32 .31 W27S = 2700K, std CRI (120°) .28 .34 .31 .28 .26 W30S = std CRI .25 .31 .273000K, .24 .23 .22 .28 .24 .22 .20 .19 .26 .22 .19 .18 .16 .24S28 .20=.17 .17 NOTE: 32’ (9754mm) max. .15 .18=.16 .16 .22S56 18’ (5486mm) max.
Lens
Finish -
T = flat clear F = flat frosted C = convex clear
MA MA = matte clear anodized
Standard CRI has a value of 75~82.
138 139
Image shows L103-XS3W30SWT-EMA
drop drop
Linear Systems
2-3/4” 70mm
L103 Linear Strip Light Application Suspended or wall mounted linear LED strip light. Source 1W, 350mA LEDs (4W/Ft or 6W/Ft)
2-1/8” 54mm
Input Current S2 = 350mA/foot S3 = 230mA/foot
1-7/8” 48mm
3-1/8” 79mm
3-7/8” 98mm
4-1/4” 108mm
Driver Remote 120V primary, constant voltage driver (not included).
S (LED spacing)
2-1/8” 54mm
LED Input Voltage 24V DC Power Consumption S2 = 8W/foot S3 = 6W/foot
1-1/4” 32mm
Dimming 0~10V dimming with remote dimmable driver (not included). See page 186-190 for Recommended Driver Chart.
1/8” 3mm
L103
www.mplighting.com
1-7/8” 48mm
1:3
L (circuit board length)
Weight 0.90lb (0.41kg)/foot. Material Aluminum and polycarbonate. RoHS compliant. 2-3/4” 70mm
Mounting Mounts directly to surface or by wall bracket, rod or cable suspension set (sold separately, see pages 168-169). Comes with 6’ (1829mm) wire lead. Power feed is 12” (305mm) from the end.
drop drop
Approval Dry locations. Approved to US and Canadian standards by CSA.
3-1/8” 79mm
Note Recommended suspension points should be 4’ (1219mm) on center maximum. 2-1/8” 54mm
3-1/8” 79mm
4-1/4” 108mm
2-1/8” 54mm
1-7/8” 1-7/8” 48mm 48mm
3-7/8” 98mm
50 See page 192 for explanation of symbols and IP ratings.
L103 4’ Length S2 Spacing 120° Flat Frosted 3000K Std 1000 lm
Shown as wall mount (SDF070) Convex clear lens
Polar Candela Distribution
Shown as rod suspension (SDF061) Flat frosted lens
Illuminance at a Distance
180° -90°
Center Beam FC
90°
-45°
45°
approx. 380 cd max.
L103 4’ Length S3 Spacing 120° Flat Frosted 3000K Std 782 lm
Polar Candela Coefficients OfDistribution Utilization
-90° RW %:
Lumen test results provided by MP Lighting integrating sphere (see page 194).
RCR: 0 1 2 3 4 -45° 5 6 7 8 9 10
80
70 .64 .58 .53 .48 .44 .41 .38 .35 .32 .30 .28
50 30 .64 .64 .56 .54 .49 .45 .43 .38 .38 .33 .34 .29 .30 .26 .28 .23 .25 .21 .230° .19 .21 .17
4.8’
3.0’
42.42
9.5’
4.4’ 8.9’
4.5’
18.86
14.3’
13.3’
6.0’
10.61
19.0’
17.7’
7.5’
6.79
23.8’
22.1’
9.0’
4.71
28.5’
26.6’
90° Spread: 111.7°
Illuminance at a Distance Effective Floor Cavity Reflectance: 20%
180°
RCC %:
169.70
0° Spread: 115.5°
0°
Beam Width
1.5’
70
0 70 .64 .62 .52 .57 .42 .52 .35 .47 .30 .43 .25 approx..40 .22 250 cd.37 .20 max. .34 .17 .32 .16 .29 .14 .28
90° 50
.62 .55 .48 .42 .37 45° .33 .30 .27 .25 .23 .21
50
30 .62 .53 .44 .38 .33 .29 .25 .23 .20 .18 .17
0 .53 .45 .38 .32 .28 .24 .21 .19 .17 .15 .14
50 1.5’ .60 .52 3.0’ .46 4.5’ .40 .36 6.0’ .32 7.5’ .29 .26 9.0’ .24 0° .22 .20
30 10 0 Center Beam FC Beam Width 0 30 20 50 30 20 50 30 20 4.7’ .55 4.5’ .57 .57 .57 .55 .60 .60 108.97 .55 .53 .51 .49 .50 .49 .48 .48 .47 .46 .45 27.24 9.0’ 9.3’ .43 .41 .44 .42 .40 .42 .40 .39 .37 .39 .36 .33 14.0’ .37 .34 12.11 .37 .3513.5’ .33 .32 .32 .29 .35 .31 .29 .33 .30 .28 .27 6.81 18.7’ 18.0’ .28 .25 .31 .27 .25 .30 .27 .24 .23 .28 .24 .22 23.4’ .25 .22 4.36 .27 .2422.5’ .21 .20 .25 .22 .19 28.0’ .22 .19 3.03 .25 .2127.0’ .19 .18 .20 .17 .23 .20 .17 .23 .19 .17 .16 Spread: Spread: .21 .18 .1590° .21 .18 .16114.6° .18 112.6° .15 .14 .17 .14 .20 .16 .14 .19 .16 .14 .13
Coefficients Of Utilization
Code L103
Length (L)80
RCC %:
-
RW %: 70 50 30 RCR: 0 .61 .61 .61 1 .56 .54 .52 2 .51 .47 .43 4 = 4’ .47 .41 .37 3 (1219mm) .43 .36 .32 4 (2438mm) 8 = 8’ 5 .39 .33 .28 X = 6custom .36 .29 .25 7 .33 .26 .22 8 .31 .24 .20 9 .29 .22 .18 10 .27 .20 .16
Spacing (s) 70
Effective Floor Cavity Reflectance: 20%
50
Color
30
50 30 50 30 20 0 70 50 30 0 .61 .60 .60 .60 .51 .57 .57 .57 .55 .55 .50 .55 .52 .51 .44 .50 .49 .47 .48 .47 .40 .50 .46 .43 .37 .44 .41 .39 .42 .40 2700K, S2 = (51mm) .34 .35 .33 .37 .452”.40 .36 .31 .39 W27S = .34 .30 .31 .28 .33 .413”.36 .31 .27 .34 W30S = .28 3000K, S3 = (76mm) .24 .38 .32 .28 .23 .31 .27 .24 .30 .26 3500K, .35between .23 .24 .21 .27 .29 .24 LEDs .20 .28 W35S = .21 .21 .21 .19 .24 .19 .33 .26 .22 .18 .25 W41S = 4100K, .17 .30 .24 .20 .16 .23 .19 .17 .22 .19 2000K, .18 .15 .21 .15 .28 .22 .18 .15 .21 W20H = .17 .16 .14 .19 .14 .27 .20 .16 .13 .20 W30H = .16 3000K,
10
20 50 .55 .52 .46 .46 .38 .41 std .32 CRI .36 .27 CRI .32 std .24 .29 std .21 CRI .26 .18 CRI .24 std .16 .22 high .20 .15 CRI .19 .13 CRI high
0
Beam
0 30 20 .52 .52 .51W .45 .44 .43 .39 .37 .36 .30 flood .34 W .31= wide .29 (120°) .27 .26 .26 .23 .22 .23 .21 .20 .21 .18 .17 .19 .16 .15 .17 .15 .14 .16 .13 .12
Lens
Power Feed -
T = flat clear F = flat frosted C = convex clear
Finish MA
E = end feed T = top feed
MA = matte clear anodized
NOTE: S2 = 12’ (3658mm) max. S3 = 18’ (5486mm) max
Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
140 141
Image shows L104-XS3W30SSF-TMA. Using SDF060 mountings
Ø1” Ø25mm
L104
www.mplighting.com
drop
L104 Linear Strip Light
drop
Application Suspended or wall mounted linear LED strip light. Source 1W, 350mA LEDs (4W/Ft or 6W/Ft) 3-1/8” 79mm
Input Current S2 = 350mA/foot S3 = 230mA/foot Driver Remote 120V primary, constant voltage driver (not included).
4-1/2” 114mm 2-3/8” S (LED spacing) 60mm
2-3/8” 60mm
LED Input Voltage 24V DC
Linear Systems
2-3/4” 70mm
2-3/8” 60mm
Power Consumption S2 = 8W/foot S3 = 6W/foot
1-1/4” 32mm
Dimming 0~10V dimming with remote dimmable driver (not included). See page 186-190 for Recommended Driver Chart.
1/8” 3mm
L (circuit board length)
Weight 0.90lb (0.41kg)/foot. Material Aluminum and polycarbonate. RoHS compliant. 2-3/4” 70mm
Mounting Mounts directly to surface or by wall bracket, rod or cable suspension set (sold separately, see pages 168-169). Wall brackets for tiltable wall mount are included. Comes with 6’ (1829mm) wire lead. Power feed is 12” (305mm) from the end.
drop 3-1/8” 79mm
Approval Dry locations. Approved to US and Canadian standards by CSA. Note Recommended suspension points should be 4’ (1219mm) on center maximum.
4-1/2” 114mm
2-3/8” 60mm
2-3/8” 60mm
50 See page 192 for explanation of symbols and IP ratings.
L104 4’ Length S2 Spacing 12° Flat Frosted 3000K Std 1060 lm
Shown as wall mount (SDF070)
Polar Candela Distribution
Illuminance at a Distance
180° -90°
Center Beam FC
90°
-45°
approx. 3000 cd max.
45°
1,351.38
0.6’
0.6’
3.0’
337.84
1.3’
1.3’
4.5’
150.15
1.9’
1.9’
6.0’
84.46
2.6’
2.6’
7.5’
54.06
3.2’
3.2’
9.0’
37.54
3.9’
3.9’
0° Spread: 24.2°
Polar Candela Coefficients OfDistribution Utilization
-90° RW %:
RCR: 0 1 2 3 4 -45° 5 6 7 8 9 10
80
70 .73 .66 .60 .55 .50 .46 .43 .40 .37 .34 .32
50 30 .73 .73 .64 .61 .55 .51 .49 .44 .43 .38 .38 .33 .35 .29 .31 .26 .29 .23 .260° .21 .24 .19
3” 76mm
2” 51mm
90° Spread: 24.2°
4-1/4” 108mm
3-5/8” 92mm
Illuminance at a Distance Effective Floor Cavity Reflectance: 20%
180°
RCC %:
Beam Width
1.5’
0°
L104 4’ Length S3 Spacing 12° Flat Frosted 3000K Std 713 lm
Shown as cable suspension (SDF061)
70
0 70 .73 .71 .59 .65 .48 .59 .40 .54 .34 .49 .29 approx..45 .42 .25 2000 cd .22 max. .39 .20 .36 .18 .34 .16 .31
90° 50
.71 .62 .54 .48 .42 45° .38 .34 .31 .28 .26 .24
50
30 .71 .60 .50 .43 .37 .33 .29 .26 .23 .21 .19
0 .61 .52 .43 .37 .32 .28 .24 .21 .19 .17 .16
50 .68 1.5’ .59 3.0’ .52 .46 4.5’ .41 6.0’ .36 7.5’ .33 .30 9.0’ .27 0° .25 .23
30 10 0 Center Beam FC Beam Width 30 20 50 30 20 50 30 20 .65 .65 .65 .62 .68 .68 901.27 .62 0.6’ .62 0.6’ .58 .56 .57 .55 .54 .55 .53 .52 225.32 1.3’ 1.3’ .49 .46 .50 .47 .45 .48 .46 .44 .44 .41 .38 .42 .42 .39 100.14 1.9’ .40 1.9’ .37 .36 .33 .39 .35 .32 .38 .35 .32 56.33 2.6’ 2.6’ .32 .28 .35 .31 .28 .34 .31 .28 3.2’ .27 3.2’ .32 .28 .25 .31 .28 .25 36.05 .24 .29 .25 .22 .28 .25 .22 25.04 .22 3.9’ .24 3.9’ .23 .20 .26 .22 .19 .26 .22 .19 Spread: Spread: .24 .20 .1790° .24 .21 .1824.2° .20 24.2° .17 .19 .16 .23 .19 .16 .22 .18 .16
0 .61 .51 .43 .36Lumen test .31results provided .26by MP Lighting .23 integrating sphere .20 .18(see page 194). .16 .15
Shown as tiltable wall mount (L104T)
3” 76mm
Coefficients Of Utilization Suspended or Wall Mount: (hardware sold separately)
Code L104 Tiltable Wall L104T
Length (L)
RCC %:
Spacing (s)
80
70
%: 70 50 30 0 70 50 30 0 - RW RCR: 0 .71 .71 .71 .71 .69 .69 .69 .60 1 .67 .64 .63 .61 .65 .63 .61 .54 2 .62 .59 .56 .53 .61 .58 .55 .48 Mount: (wall brackets included) 3 .59 .54 .50 .47 .57 .53 .50 .44 4 .55 .50 .46 .43 .54 .49 .45 .41 5 .52 .46 .42 .39 .51 .46 .42 .38 6 .50 .44 .39 .37 .49 .43 .39 .35 7 .47 .41 .37 .34 .46 .41 .37 .33 .442” .38 .35 .32 .45 .39 .35 .32 S2 = (51mm) 4 = 84’ (1219mm) 9 .43 .37 .33 .31 .42 .37 .33 .30 S3 = (76mm) 8 =108’ (2438mm) .413” .35 .31 .29 .41 .35 .32 .29
X = custom
between LEDs
Effective Floor Cavity Reflectance: 20%
50
Color
30
50 30 20 50 30 .66 .66 .66 .63 .63 .61 .59 .58 .58 .57 .56 .53 .51 .54 .52 .51 .48 .46 .50 .47 .48 .45 .42 .46 .44 .45 .41 .39 .44 .41 .42 .39 .36 .41 .38 .40 .36 .34 .39 .36 .37 .34 .38 W27S = .34 .32 2700K, .36 .33 .30 .35 .32 .34 .31 .34 W30S = .31 .29 3000K,
10
20 50 .63 .61 .56 .56 .50 .52 .45 .48 .42 .45 .38 .43 .36 .40 .34 .38 .32 CRI .36 std .30 .35 std .29 CRI .33
W35S = 3500K, std CRI W41S = 4100K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
0
Beam
0 30 20 .61 .61 .60 .55 .54 .53 .50 .49 .48 .46 .45 .43 .43 .41 .40 .40 .38 .37 .38 .36 .35 .36 .33 .33 .31 (12°) .34 S.32 = spot .32 .30 .29 = narrow .28 .31 N.29
Lens
Power Feed
51mm
-
MA 4-1/4”
3-5/8” 92mm
108mm
T = flat clear F = flat frosted
Finish 2”
MA E = end feed T = top feed
MA = matte clear anodized
flood (30°) NOTE: S2 = 12’ (3658mm) max. & S3 = 18’ (5486mm) max
Standard CRI has a value of 75~82 while high CRI has 92.
142
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
143
Image shows L106S-XS3W30SNT-MA
L106
www.mplighting.com
Linear Systems
L106 Linear LED Downlight
3” 76mm
Application Indoor linear cove, shelf, and cabinet illumination. Source 1W, 350mA LEDs (4W/Ft or 6W/Ft) Input Current S2 = 350mA/foot S3 = 230mA/foot
2” 51mm
Driver Remote 120V primary, constant voltage driver (not included).
2-5/8” 67mm
LED Input Voltage 24V DC Power Consumption S2 = 8W/foot S3 = 6W/foot
3-3/8” 86mm
S (LED spacing)
1-1/4” 32mm
Dimming 0~10V dimming with remote dimmable driver (not included). See page 186-190 for Recommended Driver Chart.
1-1/2” 38mm 1/8” 3mm
Weight 0.90lb (0.41kg)/foot.
End feed only.
L (circuit board length) 3” 76mm
Material Aluminum and polycarbonate. RoHS compliant. Mounting Surface or tiltable wall mount. Includes aluminum mounting channel with wiring compartment. Comes with 3’ (914mm) wire lead. Approval Dry locations. Approved to US and Canadian standards by CSA. 1-1/2” 38mm
50 See page 192 for explanation of symbols and IP ratings.
L106 4’ Length S2 Spacing 12° Flat Frosted 3000K Std 1060 lm
3-3/8” 86mm
Shown as tiltable wall mount (L106T)
Shown as surface mount (L106S)
Polar Candela Distribution
2” 51mm
2-5/8” 67mm
Illuminance at a Distance
180° -90°
Center Beam FC
90°
-45°
approx. 3000 cd max.
45°
L106 4’ Length S3 Spacing 12° Flat Frosted 3000K Std 713 lm
Polar Candela Coefficients OfDistribution Utilization
-90° RW %:
Lumen test results provided by MP Lighting integrating sphere (see page 194).
RCR: 0 1 2 3 4 -45° 5 6 7 8 9 10
80
70 .73 .66 .60 .55 .50 .46 .43 .40 .37 .34 .32
50 30 .73 .73 .64 .61 .55 .51 .49 .44 .43 .38 .38 .33 .35 .29 .31 .26 .29 .23 .260° .21 .24 .19
0.6’
0.6’
3.0’
337.84
1.3’
1.3’
4.5’
150.15
1.9’
1.9’
6.0’
84.46
2.6’
2.6’
7.5’
54.06
3.2’
3.2’
9.0’
37.54
3.9’
3.9’
90° Spread: 24.2°
Illuminance at a Distance Effective Floor Cavity Reflectance: 20%
180°
RCC %:
1,351.38
0° Spread: 24.2°
0°
Beam Width
1.5’
70
0 70 .73 .71 .59 .65 .48 .59 .40 .54 .34 .49 .29 approx..45 .42 .25 2000 cd .22 max. .39 .20 .36 .18 .34 .16 .31
90° 50
.71 .62 .54 .48 .42 45° .38 .34 .31 .28 .26 .24
50
30 .71 .60 .50 .43 .37 .33 .29 .26 .23 .21 .19
0 .61 .52 .43 .37 .32 .28 .24 .21 .19 .17 .16
50 1.5’ .68 .59 3.0’ .52 4.5’ .46 .41 6.0’ .36 7.5’ .33 .30 9.0’ .27 0° .25 .23
30 10 0 Center Beam FC Beam Width 30 20 50 30 20 50 30 20 0.6’ .62 0.6’ .65 .65 .65 .62 .68 .68 901.27 .62 .58 .56 .57 .55 .54 .55 .53 .52 225.32 1.3’ 1.3’ .49 .46 .50 .47 .45 .48 .46 .44 1.9’ .40 1.9’ .44 .41 .38 .42 .42 .39 100.14 .37 .36 .33 .39 .35 .32 .38 .35 .32 56.33 2.6’ 2.6’ .32 .28 .35 .31 .28 .34 .31 .28 3.2’ .27 3.2’ .32 .28 .25 .31 .28 .25 36.05 .24 .29 .25 .22 .28 .25 .22 25.04 .22 3.9’ .24 3.9’ .23 .20 .26 .22 .19 .26 .22 .19 Spread: Spread: .24 .20 .1790° .24 .21 .1824.2° .20 24.2° .17 .19 .16 .23 .19 .16 .22 .18 .16
0 .61 .51 .43 .36 .31 .26 .23 .20 .18 .16 .15
Coefficients Of Utilization Effective Floor Cavity Reflectance: 20%
Code L106
RCC Mount %:
80
RW %: 70 50 30 RCR: 0 .71 .71 .711 .67 .64 .63 2 .62 .59 .56 3 .59mount .54 .50 S = surface 4 .55 .50 .46 T = tiltable wall.46 .42 5 .52 6 .50 .44 .39 mount 7 .47 .41 .37 8 .45 .39 .35 9 .43 .37 .33 10 .41 .35 .32
70 (L) Length
0 70 50 30 0 .71 .69 .69 .69 .60 .61 .65 .63 .61 .54 .53 .61 .58 .55 .48 .53 .50 .44 .474 =.57 4’ (1219mm) .43 .54 .49 .45 .41 8’ (2438mm) .46 .42 .38 .398 =.51 .43 .39 .35 .37X =.49 custom .34 .46 .41 .37 .33 .32 .44 .38 .35 .32 .31 .42 .37 .33 .30 .29 .41 .35 .31 .29
50
30(s) Spacing
50 30 .66 .66 .61 .59 .56 .53 .51 .48 S2 = .48 .45 S3 = .45 .41 .42 .39 .40 .36 .38 .34 .36 .33 .34 .31
20 50 30 20 .66 .63 .63 .63 .58 .58 .57 .56 .51 .54 .52 .50 .50 .47 .45 .46(51mm) 2” .42 .46 .44 .42 3” .44 .41 .38 .39(76mm) .38 .36 .36 .41 LEDs between .34 .39 .36 .34 .32 .37 .34 .32 .30 .35 .32 .30 .29 .34 .31 .29
10
0
Color
0 50 30 20 .61 .61 .61 .60 .56 .55 .54 .53 .52 .50 .49 .48 .43 .48 .46 .452700K, W27S = .45 .43 .41 .40 W30S = .37 .43 .40 .383000K, .40 .38 .36 .35 W35S = 3500K, .38 .36 .33 .33 W41S = .31 .36 .34 .324100K, .35 .32 .30 .29 W20H = 2000K, .33 .31 .29 .28
std CRI std CRI std CRI std CRI high CRI W30H = 3000K, high CRI
Beam
Lens
Finish -
S = spot (12°) N = narrow flood (30°)
T = flat clear F = flat frosted
MA MA = matte clear anodized
NOTE: S2 = 12’ (3658mm) max. S3 = 18’ (5486mm) max
Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
144 145
Image shows L111C-8S1W30SS-XMA
L (length) 10-7/8” 276mm
1-3/4” 44mm
2-5/8” 67mm
5-7/8” 149mm 5-7/8” 149mm
2-5/8” 67mm 2-5/8” 67mm
Application Indoor linear downlight.
5-7/8” 149mm 5-7/8” 149mm
1-3/4” 44mm 1-3/4” 44mm
Linear Systems
10-7/8” 276mm 10-7/8” 276mm
stem
L111 Linear Downlight
5-7/8” 149mm
L (length) 5-7/8” 149mm
L111
www.mplighting.com
70mm 2-3/4” 70mm 1/4” 6mm 1/4” 6mm
drop drop
Source 1W, 350mA LEDs (6W/Ft or 12W/Ft).
2-3/4” 70mm
Input Current S1 = 350mA/foot S2 = 230mA/foot Driver Remote 120V primary. Canopy mount is powered by surface L (length) mounted driver with optional dimming controller (included). Please specify. Tiltable wall mount is powered by remote driver (not included). Power Consumption S1 = 12W/foot S2 = 6W/foot
10-7/8” 276mm
5-7/8” Dimming 0~10V dimming with remote dimmable driver for tiltable wall 149mm mount option (not included). See page 186-190 for Recommended Driver Chart. 2-5/8”
1/4” 6mm
S (LED spacing)
2-3/4” 70mm 2-3/4” 70mm
1/4” 6mm 1/4” 6mm
L (length)
S (LED spacing)
L (length)
5-7/8” 149mm
1-3/4” 44mm
Shown as canopy mount (L111C)
67mm
Weight 14lbs (6.28kg) with 4’ (1219mm) length fixture.
drop
Material Anodized aluminum. RoHS compliant. Mounting Mounts to ceiling using power canopy (included). 8’ (2438mm) fixture comes with 2 stem supports, 6’ (1829mm) maximum drop. Or mounts to wall using tiltable wall bracket. See pages S (LED spacing) 168-170 for more2-3/4” mounting options. 70mm
4-1/2” 114mm
5/8” 16mm 1/4” 6mm
L (length)
4-1/2”
5/8” 16mm
Approval Dry locations. Approved 114mm to US and Canadian standards by CSA.
50
2-3/4” 70mm
See page 192 for explanation of symbols and IP ratings.
L111 4’ Length S1 Spacing 12° 3000K Std 2410 lm
Polar Candela Distribution
2-3/4” 70mm
approx. 17500 cd max.
45°
-90° RW %:
Lumen test results provided by MP Lighting integrating sphere (see page 194).
RCR: 0 1 2 3 4 -45° 5 6 7 8 9 10
180°
80
2-1/2” 64mm
Beam Width
1,091.02
1.6’
1.6’
8.0’
272.76
3.3’
3.3’
12.0’
121.22
4.9’
4.9’
16.0’
68.19
6.5’
6.6’
20.0’
43.64
8.2’
8.2’
24.0’
30.31
9.8’
9.8’
90° Spread: 23.2°
Illuminance at a Distance Effective Floor Cavity Reflectance: 20%
70
50
30 10 0 Center Beam FC Beam Width 70 50 30 0 70 90° 50 30 0 50 30 20 50 30 20 50 30 20 0 2.4’1.03 2.4’ 1.03 1.01 1.08 1.08 1.08 1.03 1.12 1.12 1.12 301.76 1.20 1.20 1.20 1.20 1.18 1.18 1.18 1.01 4.0’ 1.15 1.13 1.10 1.08 1.13 1.10 1.08 .96 1.06 1.05 1.03 1.03 1.01 1.00 .99 .98 .97 .95 75.44 4.8’ 4.8’ 8.0’ 1.10 1.06 1.02 .99 1.08 1.04 1.01 .91 1.01 .98 .96 .98 .96 .94 .95 .94 .92 .90 7.2’ .89 7.2’ .88 .86 .94 .91 .89 .92 .96 .93 .90 33.53 1.06 1.00 .96 .92 1.04 .99 .95 .87 12.0’ 1.02 .95 .91 .87 1.00 .94 .90 .83 .92 .89 .86 .90 .87 .85 .89 .86 .84 .82 18.86 9.6’ 9.6’ 16.0’ 45° .98 .91 .86 .83 approx..97 .90 .86 .80 .89 .85 .82 .87 .84 .81 .86 .83 .80 .79 .84 .80 .78 12.0’ .85 .81 .78 12.07 .94 .87 .82 .77 20.0’ .95 .87 .82 .79 .83 .8012.0’ .77 .76 5000 cd .81 .77 .75 14.5’ .82 .78 .75 8.38 .92 .84 .79 .76 .80 .7714.4’ .74 .73 max. .91 .83 .79 .74 24.0’ .89 .81 .76 .73 .88 .81 .76 .72 .80 .75 .72 .79 .75 .72 .78 .74 .72 .71 0° Spread: Spread: .76 .72 .7090°.75 .73 .7033.5° .86 .780°.74 .70 .85 .78 .73 .69 .77 .72 33.4° .70 .68 .84 .76 .71 .68 .83 .75 .71 .67 .75 .71 .68 .74 .70 .68 .73 .70 .67 .66
70
Length 50 (L)
Coefficients Of Utilization
Code L111
RCC %:
1/4” 6mm
1/4” 6mm
4.0’
0° Spread: 23.1°
Polar Candela Coefficients OfDistribution Utilization RCC %:
Center Beam FC
90°
0°
L111 4’ Length S2 Spacing 30° 3000K Std 1250 lm
L (length)
S (LED spacing) Illuminance at a Distance
180°
-45°
Shown as canopy mount (L111T) S (LED spacing)
L (length)
-90°
2-1/2” 64mm
Mount 80
Effective Floor Cavity Reflectance: 20%
Spacing 30
(s)10
0
RW %: 70 50 30 0 70 50 30 0 50 30 20 50 30 20 50 30 20 0 RCR: 0 1.21 1.21 1.21 1.21 1.18 1.18 1.18 1.01 1.13 1.13 1.13 1.08 1.08 1.08 1.03 1.03 1.03 1.01 1 1.15 1.12 1.09 1.07 1.12 1.10 1.07 .95 1.05 1.04 1.02 1.02 1.00 .99 .98 .97 .96 .94 2 1.09 1.04 1.00 .97 1.07 1.02 .99 .89 .99 .96 .93 .96 .94 .91 .93 .91 .90 .88 S1 = 1” (25mm) C = canopy (non-dimmable) W27S = 4 = 4’ (1219mm) 3 1.04 .98 .93 .89 1.02 .96 .92 .83 .94 .90 .87 .91 .88 .85 .89 .86 .84 .82 .87 .832”.80 .89 .84 .81 S2 = .92 .87 .83 .98 .91 6.86 4 .99 (dimmable) .85 .82 .79 .78 (51mm) CD = canopy W30S = = .79 6’ (1829mm) 5 .95 .87 .81 .77 .93 .86 .81 .75 .84 .80 .76 .83 .79 .76 .81 .78 .75 .74 T = tiltable wall mount W35S = = .71 8’ (2438mm)* .75 .72 LEDs .80 .76 .72 .79 between 6 .91 .83 .77 .73 .90 .82 8.77 .78 .74 .71 .70 7 .87 .79 .73 .69 .86 .78 .73 .68 .77 .72 .69 .76 .71 .68 .75 .71 .68 .67 W41S = 8 .84 .75 .70 .66 .83 .75 .69 .65 .74 .69 .65 .73 .68 .65 .72 .68 .65 .64 W20H = only .62 .70 .65 .62 .69 .65 .62 .71 .66 .66length .62 fixture 9 .81 .72 .66 .63 .80 .71 *8’ .61 .68spacing. .63 .60 .67 .63 .60 .66 .62 .60 .63 .59 in S2 10 .78 .69 .64 .60 .77 .69 available .58 W30H =
Color
Drop (Canopy Mount Only)
Beam -
2700K, std CRI 3000K, std CRI 3500K, std CRI 4100K, std CRI 2000K, high CRI 3000K, high CRI
S = spot (12°) N = narrow flood (30°)
Finish MA
6 = 6” (152mm) min. X = custom length, 6’ (1829mm) max.
MA = matte clear anodized
NOTE: Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
146 147
Image shows L112-4S3W30S1-MA
3-3/8” 86mm
L112
www.mplighting.com 2-5/8” 67mm
Application Indoor linear downlight. Source 2.5W, 700mA LEDs (36 x 2.5W or 72 x 2.5W).
6-5/8” 168mm
Driver Integral 120V or 277V primary, constant voltage driver (please specify). Power Consumption 106W (4’) / 212W (8’)
Linear Systems
L112 Dual Linear Downlight
2-3/8” 60mm
Dimming 0~10V dimming with remote dimmable driver (not included). See page 186-190 for Recommended Driver Chart. Weight 10lbs (4.73kg) with 4’ (1219mm) length fixture.
L (circuit board length)
Material Anodized aluminum with white reflectors. RoHS compliant.
1/8” 3mm
3-3/8” 86mm
Mounting Can be mounted by rod & cable suspension sets (sold separately, see pages 168 &170). Approval Dry locations. Approved to US and Canadian standards by CSA.
2-5/8” 67mm
2-5/8” 67mm
20 See page 192 for explanation of symbols and IP ratings.
6-5/8” 168mm
2-3/8” 60mm
L112 4’ Length S3 Spacing 90° 3000K Std 4309 lm
Polar Candela Distribution
Illuminance at a Distance
1/8” 3mm
L (circuit board length) 180° -90°
Lumen test results provided by LSI.
Center Beam FC
90°
-45°
approx. 1900 cd max.
45°
Beam Width
1.5’
879.60
3.0’
2.5’
3.0’
219.90
6.0’
4.9’
4.5’
97.73
9.1’
7.4’
6.0’
54.98
12.1’
9.8’
7.5’
35.18
15.1’
12.3’
9.0’
24.43
18.1’
14.7’
0° Spread: 90.3°
0°
Shown with SDF065 and CPY52 configuration. Standoffs are 1’ (305mm) from the end for 4’ model & 1’-6” (457mm) from the end for 8’ model.
90° Spread: 78.5°
Coefficients Of Utilization Effective Floor Cavity Reflectance: 20%
RCC %:
Code L112
-
80
70
50
30
10
0
RW %: 70 50 30 0 70 50 30 0 50 30 20 50 30 20 50 30 20 0 RCR: 0 1.19 1.19 1.19 1.19 1.16 1.16 1.16 1.00 1.11 1.11 1.11 1.06 1.06 1.06 1.02 1.02 1.02 1.00 1Length .89 Voltage 1.11 1.07 1.05 1.02 (s) .89 1.01 .98 .96 .97 Color .95 .93 .94 .92 .91 Input (L) 1.04 1.01 1.09 Spacing 2 1.03 .96 .91 .86 1.00 .94 .89 .79 .91 .87 .83 .88 .84 .81 .85 .82 .79 .77 3 .68 .95 .86 .80 .74 .93 .85 .79 .69 .82 .77 .72 .79 .75 .71 .77 .73 .70 4 .60 .88 .78 .70 .65 .86 .77 S3 .70 .61 .74 .68 .63 .72 W30S .67 .63 .70 .66 .62 5 .53 .82 .71 .63 .57 .80 .70 .62 .55 .68 .61 .56 .66 .60 .56 .64 .59 .55 6 .76 .64 .56 .51 .74 .63 .56 .49 .62 .55 .50 .60 .54 .50 .59 .53 .49 4 = 4’7 (1219mm) S3 = 2.66” (68mm) W30S = 3000K, std CRI 1 =.47 120V .43 .71 .59 .51 .45 .69 .58 .51 .44 .57 .50 .45 .55 .49 .45 .54 .49 .44 .66 .54 .46 .41 .65 .53 .46 .40 8 = 8’8 (2438mm) between LEDs.52 .45 .41 .51 .45 .40 .50 .44 .40 2 =.38277V 9 .35 .62 .50 .42 .37 .61 .49 .42 .37 .48 .42 .37 .47 .41 .37 .46 .41 .37 10 .32 .58 .46 .39 .34 .57 .46 .39 .33 .45 .38 .34 .44 .38 .34 .43 .37 .34
Finish -
MA MA = matte clear anodized
NOTE: Standard CRI has a value of 75~82.
148 149
Image shows L121-XS112W30SW-MA
L121
www.mplighting.com
Linear Systems
L121 Recessed Strip Light Application Indoor recessed linear LED light for vanity, wall and ceiling downlight illumination. Source 0.07W, 20mA LEDs (1.9W/Ft, 3.9W/Ft, or 7.8W/Ft). Input Current S28 = 80mA/foot S56 = 160mA/foot S112 = 320mA/foot Driver Remote 120V or 277V primary, constant voltage driver (not included). LED Input Voltage 24V DC 4-3/8” 111mm
1/8” 3mm
Power Consumption S28 = 2.3W/foot S56 = 4.6W/foot S112 = 9.2W/foot Dimming 0~10V dimming with remote dimmable driver (not included). See page 186-190 for Recommended Driver Chart.
S (LED spacing)
Weight 16.08lbs (7.3kg) with 4’ (1219mm) length fixture. Material Anodized aluminum with flat opal white lens. RoHS compliant. 3/4” 19mm
Mounting Recessed into wall with surface mount trim. Comes with 3’ (914mm) wire lead.
L (circuit board length)
Approval Damp and dry locations. Approved to US and Canadian standards by CSA.
2-3/4” 70mm
54
4-3/8” 111mm
1/8” See page 192 for explanation of symbols 3mm and IP ratings.
L121 2’ Length S56 Spacing 120° 3000K Std 72 lm
180° -90°
-45°
Center Beam FC
90°
66.94
2.0’
3.0’
2.0’
16.73
4.0’
6.0’
7.44
6.0’
9.1’
4.18
8.1’
12.1’
5.0’
2.68
10.1’
15.1’
6.0’
1.86
12.1’
18.1’
3.0’
3/4” 19mm
approx. 70 cd max.
45°
L121 2’ Length S112 Spacing 120° 3000K Std 140 lm
4.0’
L (circuit board length)
0° Spread: 90.4°
Polar Candela Distribution
Beam Width
1.0’
0°
90° Spread: 112.9°
Illuminance at a Distance
180° -90°
Lumen test results provided by MP Lighting integrating sphere (see page 194).
Code L121
4” 102mm
S Distance (LED spacing) Illuminance at a
Polar Candela Distribution
Center Beam FC
90°
-45°
approx. 140 cd max.
45°
135.76
2.0’
3.0’
2.0’
33.94
4.0’
5.9’
3.0’
15.08
6.0’
8.9’
4.0’
8.48
8.1’
11.9’
5.0’
5.43
10.1’
14.9’
6.0’
3.77
12.1’
17.8’
0° Spread: 90.4°
0°
Length (L)
Beam Width
1.0’
Spacing (s)
90° Spread: 112.2°
Color
Beam
-
W 2 = 2’ (610mm) 4 = 4’ (1219mm) 6 = 6’ (1829mm) 8 = 8’ (2438mm)
S28 = 28 LEDs per 1’ S56 = 56 LEDs per 1’ S112 = 112 LEDs per 1’
W27S = 2700K, std CRI W30S = 3000K, std CRI
W = wide flood (120°)
Finish -
MA MA = matte clear anodized
NOTE: Standard CRI has a value of 75~82.
150 151
Image shows L161MB-48W30S12-MA
L161
www.mplighting.com
Ø2-3/8” Ø60mm
2” 51mm
Application Display case, wall wash, or picture illumination. Source 1W, 350mA LEDs (6W/Ft)
1/4” 6mm
Driver Remote 120V primary, 350mA driver (not included) LED Input Voltage 4V DC
stem 1-1/8” 29mm min.
2” 51mm
Power Consumption 7W/Ft 1” 25mm
Dimming 0~10V dimming with remote dimmable driver (not included). See page 186-190 for Recommended Driver Chart.
1” 25mm
Weight 1.82lbs (0.827kg).
Linear Systems
L161 Display Case / Artwork / Task Lighting
1” 25mm
length
Shown as C1C (canopy) ceiling mount.
Material Anodized aluminum. RoHS compliant. 1” 25mm
Mounting Ceiling or wall mount. C1C mounts to custom 2” x 2” octagonal box (included). C1M retrofits to existing standard octagonal box using custom mounting plate (included). Also available with mounting bracket for millwork installations. Comes with 6’ (1829mm) wire lead. Approval Dry locations. Approved to US and Canadian standards by CSA.
1” 25mm
1” 25mm
length
2” 51mm
1-3/8” 35mm min.
stem
40
Ø1-5/8” Ø41mm
See page 192 for explanation of symbols and IP ratings.
Shown as MB (mounting bracket) mount.
L161 12” length 85° 3000K Std 280 lm
Polar Candela Distribution
Isofootcandle Plot
180°
2
-90°
90°
1
0
1
2
2 1
Lumen test results provided by MP Lighting integrating sphere (see page 194).
approx. 230 cd max.
1
45°
-0°
2
-90°
3
Mount height: 1 ft Total LLF: 1
0°
Code
70 30 5 fc 10
0 -45°
Mount
L161
Length
Color
Stem
C1C = Ø2-3/8” x 1/4” canopy w/ custom octagonal box C1M = Ø2-3/8” x 1/4” canopy w/ retrofit mounting plate MB = Ø1-5/8” mounting bracket
Finish -
12 = 12” (305mm) W27S = 2700K, std CRI 18 = 18” (457mm) W30S = 3000K, std CRI 24 = 24” (610mm) W35S = 3500K, std CRI X = custom up to 48” W41S = 4100K, std CRI (1219mm) W20H = 2000K, high CRI W30H = 3000K, high CRI
0 = no stem 6 = 6” (152mm) 12 = 12” (305mm) X = custom up to 24” (610mm)
MA = matte clear anodized BA = black anodized
NOTE: Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
152 153
Image shows L171S-4S3W30SN6-MP
L171
www.mplighting.com
Linear Systems
L171 Linear Rail Light Application Outdoor / indoor wall grazing illumination. Source 1W, 350mA LEDs (4W/Ft or 6W/Ft). Input Current S2 = 350mA/foot S3 = 230mA/foot Driver Remote 120V primary, constant voltage driver (not included). LED Input Voltage 24V DC 2-1/4” 57mm
Power Consumption S2 = 8W/foot S3 = 7W/foot
L (length)
Dimming 0~10V dimming with remote dimmable driver (not included). See page 186-190 for Recommended Driver Chart. Weight 0.26lbs (0.12kg)/foot.
S (LED spacing)
180° max.
Material Heavy duty powder coated aluminum housing with tempered glass. Replaceable internal potted circuit boards and LEDs mounted to extruded aluminum heat sink. RoHS compliant.
5” 2-1/4” 127mm57mm
1-3/4” 45mm
Mounting Wall, ceiling or surface mounted via adjustable and lockable mounting bracket (2 mounting brackets included). 1-3/4” 44mm
1-3/8” 35mm
Approval Wet and dry locations. Approved to US and Canadian standards by CSA.
1-5/8” 41mm
1” 25mm
Ø3/8” Ø10mm
7/8” 22mm
2-3/4” 70mm
Shown as standard wall mount (W).
Note Standard 6’ (1829mm) 18 AWG water proof electrical lead is rear mounted to enable continuous row mounting.
4-1/4” 108mm Ø4-5/8” Ø117mm
65 See page 192 for explanation of symbols and IP ratings. offset
L171 4’ Length S2 Spacing 12° 3000K Std 1113 lm
Polar Candela Distribution
Shown as extended wall mount (E).
180° -90°
Center Beam FC
90°
-45°
approx. 7500 cd max.
45°
Coefficients Of Utilization Polar Candela Distribution RCC %:
Lumen test results provided by MP Lighting integrating sphere (see page 194).
80
861.68
1.2’
1.2’
6.0’
215.42
2.5’
2.5’
9.0’
95.74
3.7’
3.7’
12.0’
53.86
4.9’
4.9’
15.0’
34.47
6.1’
6.1’
18.0’
23.94
7.4’
7.4’
90° Spread: 23.1°
IlluminanceEffective at a Distance Floor Cavity Reflectance: 20% 70
180°
Beam Width
3.0’
0° Spread: 23.1°
0°
L171 4’ Length S3 Spacing 12° 3000K Std 738 lm
RW %: 70 50 30 0 70 50 30 RCR: 0 1.04 1.04 1.04 1.04 1.0290° 1.02 1.02 -90° 1 1.00 .98 .96 .95 .98 .96 .95 2 .96 .93 .90 .87 .95 .91 .89 3 .93 .88 .84 .82 .91 .87 .84 4 .89 .84 .80 .77 .88 .83 .79 5 .86 .80 .76 .73 .85 .79 .76 -45° 6 .83 .77 .73approx. .70 .8245°.76 .72 7 .81 .74 .705000 .67cd.80 .74 .70 8 .78 .71 .67max. .65 .77 .71 .67 9 .76 .69 .65 .62 .75 .69 .65 10 .73 .67 0° .63 .60 .73 .67 .63
50
30
0 50 Center 30 20 Beam 50 FC 30 .88 .97 .97 .97 .93 .93 561.93.90 .89 .843.0’ .93 .92 .90 .806.0’ .89 .86 .84 140.48.86 .84 .77 .85 .82 .80 .83 .80 62.44.80 .77 .749.0’ .81 .78 .76 .71 35.12.77 .74 12.0’ .78 .75 .72 .68 .75 .72 .69 .74 .71 15.0’ .73 .69 .6722.48.72 .69 .66 .64 15.61.69 .66 18.0’ .70 .67 .64 .62 .68 .64 .62 .67 .64 Spread: 23.2° .65 .62 .60 0° .66 .62 .60
10 20 Beam 50 Width 30 20 .93 .90 .90 .90 1.2’.85 .88 1.2’ .87 .86 .83 2.5’ .84 .82 2.5’.81 .78 .81 .79 .77 3.7’.74 .75 3.7’ .78 .76 .72 4.9’ .75 .73 4.9’.71 .69 .73 .70 .68 6.1’ .66 6.1’ .71 .68 .66 .64 7.4’ .69 .66 7.4’.64 .62 .67 .64 .62 90° Spread: 23.1° .60 .65 .62 .60
0 0 .88 .84 .80 .76 .73 .70 .67 .65 .63 .61 .59
Coefficients Of Utilization
Code L171
RCCMount %:
80
1-3/4” 44mm
Illuminance at a Distance
Length (L) 70
Effective Floor Cavity Reflectance: 20%
Spacing (s) 50
30
Color 10
0
RW %: 70 50 30 0 70 50 30 0 50 30 20 50 30 20 50 30 20 0 RCR: 0 1.02 1.02 -1.02 1.02 1.00 1.00 1.00 .86 .95 .95 .95 .91 .91 .91 .88 .88 .88 .86 1 .98 .96 .94 .93 .96 .94 .93 .82 .91 .89 .88 .88 .87 .86 .85 .84 .83 .82 2 .94 .91 .88 .85 .92 .89 .87 .78 .872”.84 .83 .84 W27S = .82 .81 .82 .80 .79 .78 S2 = (51mm) 2 = 2’ 2700K, std CRI W = standard 3 .91 .86 .83 .80 .89 .85 .82 .75 .83 .80 .78 .81 .79 .77 .79 .77 .75 .74 (76mm) (23-13/16”/605mm) 3000K, std CRI wall4 bracket .87 .82 .78 .75 .86 .81 .78 .72S3 = .793”.76 .74 .78 W30S = .75 .73 .76 .74 .72 .71 5 .84 .78 .74 .71 .83 .78 .74 .69 .76 .73 .71 .75 .72 .70 .74 .71 .69 .68 between LEDs 4 = 4’ W35S = 3500K, std CRI E = extended 6 .81 .75 .71 .68 .80 .75 .71 .67 .73 .70 .68 .72 .69 .67 .71 .69 .67 .66 (47-5/8”/1210mm) 4100K, std CRI wall7 bracket .79 .72 .68 .66 .78 .72 .68 .64 .71 .68 .65 .70 W41S = .67 .65 .69 .66 .64 .63 .69 .65 .63 .68 .65 .63 .67 .64 .62 .61 8 .76 .70 .66 .63 .75 .69 .66 .62 W20H =.65 2000K, high.59 CRI 9 .74 .68 .64 .61 .73 .67 .63 .60 .66 .63 .61 .66 .63 .60 .62 .60 10 .72 .65 .62 .59 .71 .65 .61 .58 W30H = 3000K, high.58 CRI .64 .61 .59 .64 .61 .59 .63 .61 .58
Beam
S = spot (12°) N = narrow flood (30°)
6 = 6’ (1829mm) standard X = custom
NOTE: Standard CRI has a value of 75~82 while high CRI has 92.
Offset (Extended wall bracket only)
Lead Length
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
Finish MP
6 = 6” (152mm) 12 = 12” (305mm) 18 = 18” (457mm) 24 = 24” (610mm)
MP = matte pewter
154 155
3 8
Image shows L200-6W30S-MA
L200
www.mplighting.com
3-7/8” 98mm
Application Desk or table illumination. Source 6 x 1W, 350mA LEDs Driver Remote 120V primary, plug-in driver (included).
9”-16” 229-406mm max.
Power Consumption 8W Dimming Dimmer switch mounted on base.
3” 76mm
Desk & Table Fixtures
1-3/4” 44mm
L200 6W Desk Lamp
Weight 3.71lbs (1.68kg). Material Anodized aluminum. RoHS compliant. 2-5/8” 67mm
Approval Dry locations. Approved to US and Canadian standards by CSA.
20
1-1/8” 29mm
See page 192 for explanation of symbols and IP ratings.
L200 120° 3000K Std 510 lm
Polar Candela Distribution
Isofootcandle Plot
180°
1
-90°
0
approx. 290 cd max.
45°
-0° -90°
40
2
Color
6 6 = 6 x 1W
70
Mount height: 1 ft Total LLF: 1
Wattage -
10 20
1
0°
L200
2
5 fc
0 -45°
Code
1
90° 1
Lumen test results provided by LED chip manufacturer.
3-7/8” Sq. 98mm Sq.
Finish -
W27S = 2700K, std CRI W30S = 3000K, std CRI W35S = 3500K, std CRI W41S = 4100K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
MA MA = matte clear anodized
NOTE: Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
156 157
Image shows L203-6W30S-MA
L203
www.mplighting.com
Application Desk or table illumination. Source 6 x 1W, 350mA LEDs Driver Remote 120V primary, plug-in driver (included).
2-1/8” 54mm
3” 76mm
Power Consumption 8W Dimming Dimmer switch mounted on base.
Desk & Table Fixtures
3-7/8” 98mm
3-3/8” 86mm
L203 6W Desk Lamp
Weight 3.71lbs (1.68kg). 16” 406mm
Material Anodized aluminum. RoHS compliant. Approval Dry locations. Approved to US and Canadian standards by CSA.
20 See page 192 for explanation of symbols and IP ratings.
29mm 1-1/8”
3-7/8” 98mm
L203 120° 3000K Std 510 lm
Polar Candela Distribution
Isofootcandle Plot
180°
1
-90°
0
approx. 290 cd max.
45°
-0° -90°
40
2
Color
6 6 = 6 x 1W
70
Mount height: 1 ft Total LLF: 1
Wattage -
10 20
1
0°
L203
2
5 fc
0 -45°
Code
1
90° 1
Lumen test results provided by LED chip manufacturer.
3-7/8” 98mm
Finish -
W27S = 2700K, std CRI W30S = 3000K, std CRI W35S = 3500K, std CRI W41S = 4100K, std CRI W20H = 2000K, high CRI W30H = 3000K, high CRI
MA MA = matte clear anodized
NOTE: Standard CRI has a value of 75~82 while high CRI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
158 159
Hardware
Code RAL001
Length
Option
-
Low-Voltage Single Rail System - SR & SF
Single rail
4 = 4’ (1219mm) 8 = 8’ (2438mm)
S = straight C1 = curved 1
Code END001
5/8” 16mm
MC MC = matte chrome
-
Please specify.
5/8” 16mm
MC MC = matte chrome
Code
Stand-off
Used to cap end of rail.
1” 25mm
Finish -
Joined with joiners on page 162.
3/8” 10mm
Finish
End cap
SDF010
Finish
Ø1” Ø25mm
MC
1’ from end and spacing 3’ on center suggested.
MC = matte chrome 2-1/8” 54mm
Code SDF011
Offset -
Stand-off
Stand-off
Option
S1 = swivel 1
Offset
For sloped ceiling applications.
1’ from end and spacing 3’ on center suggested. Field adjustable drop.
drop
Finish -
S1 = swivel
Ø1” Ø25mm
MC = matte chrome
Option
1
MC
For sloped ceiling applications.
4 = 4” (101mm) 7 = 7” (178mm) X = custom
1’ from end and spacing 3’ on center suggested.
offset
Finish -
24 = 24” (610mm) X = custom
Ø1” Ø25mm
For sloped ceiling applications.
-
Code SDF013
1
MC MC = matte chrome
S1 = swivel
Drop
Stand-off
Finish -
4 = 4” (101mm) 7 = 7” (178mm) X = custom
Code SDF012
Option
MC MC = matte chrome
Ø1” Ø25mm offset
Ø1-3/8” Ø35mm
Used to support cross-connected single rail system.
Code SDF014
Drop
Option
-
24 = 24” (610mm) X = custom
S = swivel 1
1
Ø1” Ø25mm
MC
Used to support cross-connected single rail system. Field adjustable drop.
MC = matte chrome drop
For sloped ceiling applications.
Ø1-3/8” Ø35mm
Code SDF015
Offset -
Stand-off
1’ from end and spacing 3’ on center suggested.
Finish MC
12 = 12” (305mm) X = custom
MC = matte chrome
Ø1” Ø25mm
Low-Voltage Single Rail System - SR & SF
Stand-off
Finish
Hardware
www.mplighting.com
1-78” 48mm
offset
Code SDF016 Stand-off
Finish -
MC
Wall flush Stand-off. 1’ from end and spacing 3’ on center suggested.
Ø1” Ø25mm
MC = matte chrome 1-3/8” 35mm
160 161
X = custom
Code
Code
Finish -
Conductive Joiner
-
MC MC = matte chrome
Code
Sold in pairs.
1-1/8” 29mm
Sold in pairs.
1-1/4” 32mm
Finish -
Sold in pairs.
2-1/4” 57mm
Finish
Conductive Joiner
Conductive Joiner
Ø1/8” Ø3mm
MC MC = matte chrome
Code
JON004
1-3/8” 35mm
C = conductive I = insulated
JON003
MC = matte chrome
Finish
Joiner
JON002
MC
°
JON001
-
Ø1/4” Ø6mm
15
Low-Voltage Single Rail System - SR & SF
End feed
Sold in pairs.
Finish
°-3
END011
Lead Length
45
Hardware
Code
1” 25mm
MC MC = matte chrome
1-7/8” 48mm
Sold in pairs.
Code CPY010
Finish -
MC MC = matte chrome
2-3/8” 60mm
Code CPY011
Offset -
Canopy
4 = 4” (101mm) 7 = 7” (178mm) X = custom
Code CPY012
Finish
Canopy
MC MC = matte chrome
offset
Stem can be used as a support.
Used with remote transformer to power system. Mounts to standard octagonal box. Stem can be used as a support.
Offset -
Ø4-5/8” Ø117mm
Used with remote transformer to power system. Mounts to standard octagonal box.
Finish -
4 = 4” (101mm) 7 = 7” (178mm) X = custom
Ø4-5/8” Ø117mm
MC MC = matte chrome
offset
Used with 2 remote transformers to power 2 sections of system. A JON001-I joiner must be used between the 2 feeds to isolate and join rails together. Mounts to standard octagonal box.
Low-Voltage Single Rail System - SR & SF
Canopy
Ø4-5/8” Ø117mm
Hardware
www.mplighting.com
Stem cannot be used as a support.
Code CPY013 Canopy
Offset -
Finish -
15 = 15” (381mm) X = custom
Ø4-5/8” Ø117mm
MC MC = matte chrome cord
offset
Used with remote transformer to power system. Mounts to standard octagonal box. Also can be used as a power feed for wall mount or sloped ceiling applications. Cord cannot be used as a support
162 163
Hardware
Code CPY015
Offset -
Low-Voltage Single Rail System - SR & SF
Canopy
12 = 12” (305mm) X = custom
Used with remote transformer to power system. Mounts to standard octagonal box.
Finish MC MC = matte chrome
Stem can be used as a support.
Ø4-5/8” Ø117mm
2-1/8” 54mm
offset
Code CPY016
Finish -
Canopy
MC
4-3/4” 121mm
MC = matte chrome
1-1/4” 32mm
Code CPY018
Wall Flush canopy. Used with remote transformer to power system. Mounts to single gang box.
3-1/8” 79mm
1-1/2” 38mm
This can be used as a support.
1-1/4” 32mm
Used with remote transformer to power system. Mounts to standard octagonal box.
Finish -
Canopy
MC
Ø4-5/8” Ø117mm
MC = matte chrome
Feed cannot be used as a support.
Code SLD Surface Mount LED Driver
-
Mount
Wattage
SR
100W
SR = single rail
100W = 100 watts
10-7/8” 276mm
offset
Dimming
OFFSET
Finish -
D = dimmable N = non-dimmable
1-3/4” 44mm
5-7/8” 149mm
S4 = 4” (101mm) stem S7 = 7” (178mm) stem SX = custom stem length F151 = 15” (381mm) flexible cord FX1 = custom flexible cord 1
MC MC = matte chrome
For sloped ceiling applications.
Surface Mounts to standard octagonal box. Used to power single circuit of system. 100% duty cycle. Integral push button circuit breaker. 120V-277V input. Comes with 24V LED driver power system (please specify). Also can be used as a power feed for wall mount or sloped ceiling applications, if flexible cord option is chosen1. Cord cannot be used as a support. Dry locations. Approved to US and Canadian standards by CSA.
Code RAL004
Length
Option
-
6 = 6’ (1829mm) 12 = 12’ (3658mm)
S = straight C1 = curved 1
Code END004
-
Code
Lead Length -
Joiner
Finish
MC = matte chrome 5/8” 16mm
Code
Finish -
C = conductive I = insulated
Stand-off
1-5/8” 41mm
4” 102mm
MC
1-5/8” 41mm
5/8” 16mm
MC = matte chrome
Finish -
1-5/8” 41mm
2-3/4” 70mm
MC
Lead Length
Joiner
SDF040
1/2” 13mm
-
-
Used to cap end of rail.
1” 25mm
C = conductive I = insulated
Code JON006
Please specify.
MC MC = matte chrome
Joined with joiners on page 165.
1/4” 6mm
Finish
End cap
JON005
MC MC = matte chrome
Aluminum, hand bendable, cuttable, separate neutral.
1-1/4” 32mm
Low-Voltage Dual Circuit Rail System - DC
Dual circuit rail
Finish
Hardware
www.mplighting.com
1’ from end and spacing 3’ on center suggested.
Ø1” Ø25mm
MC MC = matte chrome
2-3/4” 70mm
Code SDF041
Offset -
Stand-off
Stand-off
Finish -
4 = 4” (101mm) 7 = 7” (178mm) X = custom
Code SDF042
Option
S = swivel 1
Option
-
Finish -
S = swivel 1
1
1’ from end and spacing 3’ on center suggested.
offset
For sloped ceiling applications.
Drop
24 = 24” (610mm) X = custom
MC MC = matte chrome
1
Ø1” Ø25mm
For sloped ceiling applications.
MC
Ø1” Ø25mm
1’ from end and spacing 3’ on center suggested. Field adjustable drop.
MC = matte chrome drop
164 165
Hardware
Code SDF045
Offset -
Low-Voltage Dual Circuit Rail System - DC
Stand-off
1’ from end and spacing 3’ on center suggested.
Finish -
12 = 12” (305mm) X = custom
MC MC = matte chrome
Ø1” Ø25mm
2-1/2” 64mm
offset
Code CPY041
Offset -
Canopy
Finish -
4 = 4” (101mm) 7 = 7” (178mm) X = custom
Ø4-5/8” Ø117mm
MC
offset
MC = matte chrome
Ø1-1/4” Ø32mm
Used with 1 remote transformer to power single circuit or 2 remote transformers to power 2 circuits of the dual circuit system. Mounts to standard octagonal box. Stem can be used as a support.
Code CPY043
Offset -
Canopy
Finish -
15 = 15” (381mm) X = custom
Ø4-5/8” Ø117mm
MC MC = matte chrome cord
offset
Used with remote transformer to power single circuit when a traditional solid power feed is not feasible. Mounts to standard octagonal box. Also can be used as a power feed for wall mount or sloped ceiling applications. Cord cannot be used as a support.
Code CPY044 Canopy
Offset -
Finish -
15 = 15” (381mm) X = custom
MC
Ø4-5/8” Ø117mm
MC = matte chrome cord
offset
Used with remote transformer to power 2 circuits of the dual circuit system when a traditional solid power feed is not feasible. Mounts to standard octagonal box. Also can be used as a power feed for wall mount or sloped ceiling applications. Cord cannot be used as a support.
Code SLD
Wattage
DC
100W
DC = dual circuit rail
100W = 100 watts
10-7/8” 276mm
offset
Dimming
OFFSET
Option
Finish -
D = dimmable N = non-dimmable
S4 = 4” (101mm) stem S7 = 7” (178mm) stem SX = custom stem length F151 = 15” (381mm) flexible cord FX1 = custom flexible cord
1-3/4” 44mm
1
5-7/8” 149mm
S = swivel 1
MC MC = matte chrome
For sloped ceiling applications.
Surface Mounts to standard octagonal box. Used to power single circuit of system. 100% duty cycle. Integral push button circuit breaker. 120V-277V input. Comes with 24V LED driver power system (please specify). Also can be used as a power feed for wall mount or sloped ceiling applications, if flexible cord option is chosen. Only feeds one circuit of dual circuit track. Cord cannot be used as a support. Dry locations. Approved to US and Canadian standards by CSA.
Low-Voltage Dual Circuit Rail System - DC
Surface Mount LED Driver
-
Mount
Hardware
www.mplighting.com
166 167
Hardware
Code SDF070
Finish -
Linear System
Wall Mount Bracket
Fixed angle wall mount bracket for use with L103, L104, and 3CT.
2-7/8” 73mm
Adjustable angle wall stand-off for use with L104, L106 and L111.
MC = matte chrome 3-1/8” 79mm
Code SDF071
MC
2-3/4” 70mm
Finish -
MC
Maximum angle ±100° from horizontal.
MC = matte chrome
Stand-off
2-1/2” 64mm
Code SLD
Wattage -
Surface Mount LED Driver
Dimming
OFFSET
100W
Finish -
100W = 100 watts
D = dimmable N = non-dimmable
S12 = 12” (305mm) stem SX = custom stem length F151 = 15” (381mm) flexible cord FX1 = custom flexible cord 1
10-7/8” 276mm
offset
For sloped ceiling applications. 1-3/4” 44mm
5-7/8” 149mm
MC MC = matte chrome
Sold in pairs.
Surface Mounts to standard octagonal box. For use with L103, L104, and L112. Used to power single circuit of system. 100% duty cycle. Integral push button circuit breaker. 120V-277V input. Comes with 24V LED driver. Also can be used as a power feed for wall mount or sloped ceiling applications, if flexible cord option is chosen. Stem or cord cannot be used as a support. Dry locations. Approved to US and Canadian standards by CSA.
Code CPY052
Drop -
Canopy
Finish -
12 = 12” (305mm) X = custom
MC
Ø4-5/8” Ø117mm
For use with L112.
MC = matte chrome
drop
Code CPY053 Canopy
Drop -
Finish -
12 = 12” (305mm) X = custom
MC
4-5/8” Sq. 117mm Sq.
MC = matte chrome
drop
For use with L112.
Code CPY054
Offset -
-
Ø4-5/8” Ø117mm
MC
15 = 15” (381mm) X = custom
MC = matte chrome cord
offset
For use with L103, L104, and L111. Used with remote driver to power system. Mounts to standard octagonal box. Also can be used as a power feed for wall mount or sloped ceiling applications.
Linear System
Canopy
Finish
Hardware
www.mplighting.com
Cord cannot be used as a support Code CPY055
Offset -
Canopy
Finish -
Sq.4-5/8” Sq.117mm
MC
15 = 15” (381mm) X = custom
MC = matte chrome cord
Code SDF060
Drop -
Stand-off
SDF061
ø1” ø25mm
MC
drop
Option
Finish -
1
1
Drop
For sloped ceiling applications.
Ø1/4” rod suspension set for use with L103, L104, and 3CT.
offset
Finish -
24 = 24” (610mm) X = custom
MC
ø1” ø25mm
MC = matte chrome
S = swivel
12 = 12” (305mm) X = custom
-
Cable suspension set for use with L103, L104, and 3CT.
MC = matte chrome
-
Code
Stand-off
-
Offset
Stand-off
SDF062
Finish
24 = 24” (610mm) X = custom
Code
offset
MC
ø1-1/8” ø29mm
Cable suspension set for use with L111.
MC = matte chrome drop
168 169
Hardware
Code SDF063
Offset
Linear System & LED Driver Enclosures
S = swivel For sloped ceiling applications.
Option
Finish -
S1 = swivel
12 = 12” (305mm) X = custom
Ø7/16” rod suspension set for use with L111.
MC = matte chrome
For sloped ceiling applications.
Finish -
24 = 24” (610mm) X = custom
MC
ø1-1/8” ø29mm
offset 1
Drop -
Ø1/4” rod suspension set for use with L111.
offset 1
-
Code
MC
ø1-1/8” ø29mm
MC = matte chrome
1
Offset
Stand-off
Stand-off
12 = 12” (305mm) X = custom
Code
SDF065
Finish
-
Stand-off
SDF064
Option
MC
Ø1-1/8” Ø29mm
MC = matte chrome drop
Cable suspension set for use with L112.
Code 3CT
Length -
1-3/8” 35mm
04 = 4’ (1219mm) 08 = 8’ (2438mm) 12 = 12’ (3658mm)
BK = black S = silver
1-1/4” 32mm
3CTPWB Power Wire Bending Tool
Code
Finish -
End Cap
Finish -
Live End Feed
Finish -
Live End Feed Reverse Polarity
Finish
BK = black S = silver
Code
Live Middle Feed
2” 51mm
-
Straight Line Coupler
3CT401
2” 51mm
BK = black S = silver
Code 3CT301
1/8” 3mm
BK = black S = silver
Code 3CT202
1-1/4” 32mm
BK = black S = silver
Code 3CT201
Joined with connectors on page 172-173.
After the track has been cut to the desired length, the conductors have to be bent at a 90° angle using 3CTPWB tool.
Code
3CT101
Tracks can be field cut and joined together.
3 Circuit Track - 3CT
3CT Track
Finish
Hardware
www.mplighting.com
Finish BK = black S = silver
3-7/8” 98mm
Note: Red line shows polarity.
170 171
Hardware
Code 3CT501
Finish -
3 Circuit Track - 3CT
BK = black S = silver
Feedable L-Connector Outside
Code 3CT502
BK = black S = silver
Finish
BK = black S = silver
Code
BK = black S = silver
2-5/8” 67mm
1-3/8” 35mm
Finish -
Feedable T-Connector Inside Right
BK = black S = silver
Code
1-3/8” 35mm
2-5/8” 67mm 3-7/8” 98mm
Finish -
Feedable T-Connector Inside Left
BK = black S = silver
1-3/8” 35mm
2-5/8” 67mm 3-7/8” 98mm
Code
Feedable X-Connector
1-3/8” 35mm
3-7/8” 98mm
-
Code
3CT701
2-5/8” 67mm
Finish
Feedable T-Connector Outside Left
3CT604
3-7/8” 98mm
-
Feedable T-Connector Outside Right
3CT603
2-5/8” 67mm
2-5/8” 67mm
Code
3CT602
2-5/8” 67mm
Finish
Feedable L-Connector Inside
3CT601
2-5/8” 67mm
Finish -
1-3/8” 35mm
BK = black S = silver
Note: Red line shows polarity.
3-7/8” 98mm
Code 3CT801
-
Code -
BK = black S = silver
Code
1-1/8” 29mm
BK = black S = silver
1/2” 13mm 1-1/4” 32mm
Finish 3/4” 19mm
-
T-Bar Ceiling Clamp
BK = black S = silver
Code
Option
-
Finish -
12 = 12” (305mm) X = custom
Code
S1 = swivel 1
MC = matte chrome
S = swivel 1
For sloped ceiling applications.
offset
Finish -
1
Ø7/16” rod. For use with 3CT.
ø7/16” ø12mm
Option
-
ø4-5/8” ø117mm
MC
For sloped ceiling applications.
Offset
12 = 12” (305mm) X = custom
1/2” 13mm 1-1/4” 32mm
Offset
Canopy
Canopy
1-1/4” 32mm
Finish
Code
CPY051
1/2” 13mm
BK = black S = silver
Recessed T-Bar Ceiling Clamp
CPY050
1” 25mm
-
Code
3CT1202
2” 51mm
Finish
Ceiling Clamp
3CT1201
Cannot be used to feed track.
Finish
Flexible Connector
3CT1001
2” 51mm
BK = black S = silver
3 Circuit Track - 3CT
Adjustable Connector
3CT901
Cannot be used to feed track.
Finish
Hardware
www.mplighting.com
4-5/8” Sq. 117mm Sq.
MC MC = matte chrome
Ø7/16” rod. For use with 3CT.
offset ø7/16” ø12mm
Note: Red line shows polarity.
172 173
Hardware
Code SDF070
Finish -
3 Circuit Track - 3CT
Wall Mount Bracket
MC = matte chrome BK = black
Code 3CT3001
BK = black S = silver
Drop -
Stand-off
Finish -
ø1” ø25mm
MC
drop
Offset
Option
-
Finish -
12 = 12” (305mm) X = custom
Cable suspension set for use with L103, L104, and 3CT.
MC = matte chrome
24 = 24” (610mm) X = custom
Code
Stand-off
Track adapter will come automatically with fixture.
-
Code
SDF061
Fixed angle wall mount bracket.
3-1/8” 79mm
Finish
Replacement Track Adapter
SDF060
2-3/4” 70mm
S = swivel 1
MC
ø1” ø25mm
MC = matte chrome offset
1
For sloped ceiling applications.
Ø1/4” rod suspension set for use with L103, L104, and 3CT.
ACCS-SH Metal Shroud
3/4” 19mm
For use with L221 & L222. Can use Shroud with up to two lenses.
Accessories
www.mplighting.com
Ø1-31/32 Ø50mm
ACCS-SHB Metal Shroud, Black
ACCS-BE Beam Elongator Ø1-31/32 Ø50mm
For use with L221 & L222. Can use up to two lenses plus shroud.
ACCS-CS Crystal Spreader
ACCS-MS Mistlite Spreader
ACCS-ELB Eggcrate Louver, Black
Holder is extra.
ACCS-LH Lens Holder
ACCS-LM Louver, matte anodized ACCS-LB Louver, black anodized
1/4” 6mm
For use with L01~L04.
Ø1-3/8” Ø35mm
174 175
Drivers
LED8W350i DIMMABLE Code
Features Class 2, limited output and current with isolation for safe operation. Tight regulated output (1% line, 5% load) to maximize LED performance. AC Input Voltage 120V ~ 240V, 60Hz DC Output Voltage 3 ~ 24V DC
Dimmable
DC Output Current 350mA Constant Current Output Wattage 8W Max Dimming Function Yes (0~10V Dimming) Operating Temperature -20 ~ 50°C (-4 ~ 122°F) Weight 200g (0.41 lbs)
Constant Current
Dimensions L 2-3/8” (60mm), W 2-3/8” (60mm), H 1-1/4” (32mm) L 3-1/8” (79mm), W 1-1/2” (38mm). 7/8” (22mm)
Recommended Use 1-6 x 1W LEDs
Approval Dry locations. Approved to US and Canadian standards by CSA.
LED20W700i DIMMABLE Code
Features UL Class 2, limited output and current with isolation for safe operation. Tight regulated output (1% line, 5% load) to maximize LED performance. AC Input Voltage 120V, 60Hz DC Output Voltage 5.6 ~ 24V DC DC Output Current 700mA Constant Current Output Wattage 20W Max Dimming Function Yes (0~10V Dimming) Operating Temperature -40 ~ 60°C (-40 ~ 140°F) Weight 272g (0.60 lbs) Dimensions L 3” (76mm), W 3-1/4” (83mm), H 1-3/8” (35mm)
Constant Current
Approval Damp and dry locations. Approved to US and Canadian standards by CSA.
Recommended Use 2-6 x 2.5W LEDs
LED25W1050i DIMMABLE Code
Features UL Class 2, limited output and current with isolation for safe operation. Tight regulated output (1% line, 5% load) to maximize LED performance. AC Input Voltage 120V, 60Hz DC Output Voltage 5.6 ~ 24V DC DC Output Current 1.05A Constant Current Output Wattage 25.2W Max Dimming Function Yes (0~10V Dimming) Operating Temperature -40 ~ 60°C (-40 ~ 140°F) Weight 159g (0.35 lbs)
Constant Current
Dimensions L 3” (76mm), W 3-1/4” (83mm), H 1-3/8” (35mm)
Recommended Use 12, 15, or 18 x 1W LEDs
Approval Dry locations. Approved to US and Canadian standards by CSA.
Note: All drivers must be de-rated by 30%. For other configurations consult Recommended Drivers for LED Fixtures Tool online. http://mplighting.com/tools/FixtureToDriver/FixtureRecomDrivers.aspx
TLDDLV60W5000 DIMMABLE with TLC010i Code
Features UL Class 2, limited output and current with isolation for safe operation. Multiple voltage from 120 to 277 volts. Tight regulated output (1% line, 5% load) to maximize LED performance.
Drivers
www.mplighting.com
AC Input Voltage 120 ~ 277V, 50/60Hz DC Output Voltage 12V Constant Voltage
Output Wattage 60W Max Dimming Function With TLC010i Dimming Controller (sold separately) Operating Temperature -40 ~ 60°C (-40 ~ 140°F)
Dimmable
DC Output Current 0.1 ~ 5.00A Max
Weight 635g (1.40 lbs) Dimensions L 9-3/8” (238mm), W 1-3/4” (44mm), H 1-1/4” (32mm)
Constant Voltage
Approval Outdoor Rated. Approved to US and Canadian standards by CSA.
Recommended Use 2-12 x 3W fixtures 66
TLDDLV100W4100 DIMMABLE with TLC010i Code
Features UL Class 2, limited output and current with isolation for safe operation. Multiple voltage from 120 to 277 volts. Tight regulated output (1% line, 5% load) to maximize LED performance. AC Input Voltage 120 ~ 277V, 50/60Hz DC Output Voltage 24V Constant Voltage DC Output Current 0.1 ~ 4.10A Max Output Wattage 100W Max Dimming Function With TLC010i Dimming Controller (sold separately) Operating Temperature -40 ~ 60°C (-40 ~ 140°F) Weight 635g (1.40 lbs)
Constant Voltage
Dimensions L 9-3/8” (238mm), W 1-3/4” (44mm), H 1-1/4” (32mm)
Recommended Use 2-6 L72 or linear fixtures
Approval Outdoor Rated. Approved to US and Canadian standards by CSA. 66
TLDAV60W9 DIMMABLE with TLC010i Code
Features UL Class 2, limited output and current with isolation for safe operation. 9V (factory set) constant voltage output to maximize LED performance and life. AC Input Voltage 100V ~ 240V, 47~63Hz DC Output Voltage 8.7V ~ 10.5V Constant Voltage DC Output Current 0 ~ 5A Output Wattage 60W Max Dimming Function With TLC010i Dimming Controller (sold separately) Operating Temperature -20 ~ 60°C (-4 ~ 140°F)
Constant Voltage
Weight 400g (0.88 lbs)
Recommended Use 2-12 x 3W fixtures and 1-6 x 7W fixtures
Dimensions L 7-1/8” (181mm), W 2-3/8” (61mm), H 1-3/8” (35mm) Approval Outdoor Rated. Approved to US and Canadian standards by CSA. 64 Note: All drivers must be de-rated by 30%. For other configurations consult Recommended Drivers for LED Fixtures Tool online. http://mplighting.com/tools/FixtureToDriver/FixtureRecomDrivers.aspx
176 177
Drivers
TLDAV60W12 DIMMABLE with TLC010i Code
Features UL Class 2, limited output and current with isolation for safe operation. 12V (factory set) constant voltage output to maximize LED performance and life. AC Input Voltage 100V ~ 240V, 47~63Hz DC Output Voltage 10.8V ~ 13.2V Constant Voltage
Dimmable
DC Output Current 0 ~ 5A Output Wattage 60W Max Dimming Function With TLC010i Dimming Controller (sold separately) Operating Temperature -20 ~ 60°C (-4 ~ 140°F)
Constant Voltage
Weight 400g (0.88 lbs)
Recommended Use 2-12 x 3W fixtures and 2-6 x 7W fixtures
Dimensions L 7-1/8” (181mm), W 2-3/8” (61mm), H 1-3/8” (35mm) Approval Outdoor Rated. Approved to US and Canadian standards by CSA. 64
TLDAV100W12 DIMMABLE with TLC010i Code
Features UL Class 2, limited output and current with isolation for safe operation. 12V (factory set) constant voltage output to maximize LED performance and life. AC Input Voltage 100V ~ 240V, 47~63Hz DC Output Voltage 10.2V ~ 12V Constant Voltage DC Output Current 3.75A ~ 5A Output Wattage 60W Max Dimming Function With TLC010i Dimming Controller (sold separately) Operating Temperature -30 ~ 50°C (-22 ~ 122°F) Weight 520g (1.15 lbs)
Constant Voltage
Dimensions L 7-7/8” (200mm), W 2-3/4” (70mm), H 1-3/8” (35mm)
Recommended Use 2-8 x 7W fixtures
Approval Outdoor Rated. Approved to US and Canadian standards by CSA. 64
TLDAV100W15 DIMMABLE with TLC010i Code
Features UL Class 2, limited output and current with isolation for safe operation. 15V (factory set) constant voltage output to maximize LED performance and life. AC Input Voltage 100V ~ 277V, 47~63Hz DC Output Voltage 12.8V ~ 15V Constant Voltage DC Output Current 3.75A ~ 5A Output Wattage 75W Max Dimming Function With TLC010i Dimming Controller (sold separately) Operating Temperature -30 ~ 50°C (-22 ~ 122°F) Weight 520g (1.15 lbs)
Constant Voltage
Dimensions L 7-7/8” (200mm), W 2-3/4” (70mm), H 1-3/8” (35mm)
Recommended Use 1-6 x 10W fixtures and 1-18 x 4W fixtures
Approval Outdoor Rated. Approved to US and Canadian standards by CSA. 64 Note: All drivers must be de-rated by 30%. For other configurations consult Recommended Drivers for LED Fixtures Tool online. http://mplighting.com/tools/FixtureToDriver/FixtureRecomDrivers.aspx
TLDAV100W20 DIMMABLE with TLC010i Code
Features UL Class 2, limited output and current with isolation for safe operation. 20V (factory set) constant voltage output to maximize LED performance and life.
Drivers
www.mplighting.com
AC Input Voltage 100V ~ 277V, 47~63Hz DC Output Voltage 17V ~ 20V Constant Voltage
Output Wattage 96W Max Dimming Function With TLC010i Dimming Controller (sold separately) Operating Temperature -30 ~ 50°C (-22 ~ 122°F)
Constant Voltage
Weight 520g (1.15 lbs)
Recommended Use L72, L73, L76, L96, L98, L99, and linear systems
Dimensions L 7-7/8” (200mm), W 2-3/4” (70mm), H 1-3/8” (35mm)
Dimmable
DC Output Current 3.6A ~ 4.8A
Approval Outdoor Rated. Approved to US and Canadian standards by CSA. 64
TLDAV100W24 DIMMABLE with TLC010i Code
Features UL Class 2, limited output and current with isolation for safe operation. 24V (factory set) constant voltage output to maximize LED performance and life. AC Input Voltage 100V ~ 277V, 47~63Hz DC Output Voltage 20.4V ~ 24V Constant Voltage DC Output Current 3A ~ 4A Output Wattage 96W Max Dimming Function With TLC010i Dimming Controller (sold separately) Operating Temperature -30 ~ 50°C (-22 ~ 122°F) Weight 520g (1.15 lbs)
Constant Voltage
Dimensions L 7-7/8” (200mm), W 2-3/4” (70mm), H 1-3/8” (35mm)
Recommended Use L72, L73, L76, L96, L98, L99, and linear systems
Approval Outdoor Rated. Approved to US and Canadian standards by CSA. 64
TLC010i Dimming
Features UL Class 2, designed for dimmable drivers. Pulse Width Modulation (PWM) Dimming. Provides 0-10V Dimming control. UL Outdoor Damp location rated, IP66. Fully potted for moisture resistance.
Controller
Input Voltage Range 12 ~ 24 V DC
Code
DC Output Voltage 12 ~ 24 V DC DC Output Current 5000mA Max at 12V. 4100mA Max at 24V Dimming Control 0-10V Operating Temperature -40 ~ 60°C (-40 ~ 140°F) Weight 136g (0.30 lbs) Dimensions L 5-1/8” (130mm), W 1-3/8” (35mm), H 1” (25mm) Recommended Use Dimming module for use with 12V or 24V constant voltage drivers.
Approval Outdoor Rated. Approved to US and Canadian standards by CSA. 66
Note: All drivers must be de-rated by 30%. For other configurations consult Recommended Drivers for LED Fixtures Tool online. http://mplighting.com/tools/FixtureToDriver/FixtureRecomDrivers.aspx
178 179
Drivers
LED3W350L Code
Features Compact size that maximizes design flexibility. 110, 220, 240 full range AC input. Tight regulated constant current output to maximize LED performance. AC Input Voltage 100 ~ 240V, 50/60Hz DC Output Voltage 3 ~ 12V DC
Non-Dimmable
DC Output Current 350mA Constant Current Output Wattage 3.5W Max Dimming Function No Operating Temperature -20 ~ 60°C (-4 ~ 140°F) Weight 89.5g (0.20 lbs)
Constant Current
Dimensions L 2-5/8” (67mm), W 1-3/8” (35mm), H 7/8” (22mm)
Recommended Use 1-2 x 1W LEDs
Approval Dry locations. Approved to US and Canadian standards by CSA.
LED8W350L Code
Features Compact size that maximizes design flexibility. 110, 220, 240 full range AC input. Tight regulated constant current output to maximize LED performance. AC Input Voltage 100 ~ 240V, 50/60Hz DC Output Voltage 3 ~ 36V DC DC Output Current 350mA Constant Current Output Wattage 12W Max Dimming Function No Operating Temperature -20 ~ 60°C (-4 ~ 140°F) Weight 89.5g (0.20 lbs)
Constant Current
Dimensions L 2-5/8” (67mm), W 1-3/8” (35mm), H 7/8” (22mm)
Recommended Use 2-7 x 1W LEDs
Approval Dry locations. Approved to US and Canadian standards by CSA.
LED9W700L Code
Features Compact size that maximizes design flexibility. 110, 220, 240 full range AC input. Tight regulated constant current output to maximize LED performance. AC Input Voltage 100 ~ 240V, 50/60Hz DC Output Voltage 3 ~ 21V DC DC Output Current 700mA Constant Current Output Wattage 9W Max Dimming Function No Operating Temperature -10 ~ 40°C (14 ~ 104°F) Weight 89.5g (0.20 lbs)
Constant Current
Dimensions L 2-5/8” (67mm), W 1-3/8” (35mm), H 7/8” (22mm)
Recommended Use 1-3 x 2.5W LEDs
Approval Dry locations. Approved to US and Canadian standards by CSA.
Note: All drivers must be de-rated by 30%. For other configurations consult Recommended Drivers for LED Fixtures Tool online. http://mplighting.com/tools/FixtureToDriver/FixtureRecomDrivers.aspx
LED10W350D Code
Features UL Class 2, limited output and current with isolation for safe operation. Tight regulated output (1% line, 5% load) to maximize LED performance.
Drivers
www.mplighting.com
AC Input Voltage 120V, 60Hz DC Output Voltage 2.8 ~ 28V DC
Output Wattage 10W Max Dimming Function No Operating Temperature -40 ~ 60°C (-40 ~ 140°F) Weight 136g (0.30 lbs)
Constant Current
Dimensions L 5-1/8” (130mm), W 1-3/8” (35mm), H 1” (25mm)
Recommended Use 2-7 x 1W LEDs
Approval Outdoor Rated. Approved to US and Canadian standards by CSA.
Non-Dimmable
DC Output Current 350mA Constant Current
66
LED12W350 Code
Features UL Class 2, limited output and current with isolation for safe operation. Tight regulated output (1% line, 5% load) to maximize LED performance. AC Input Voltage 120V, 60Hz DC Output Voltage 2.6 ~ 32.8V DC DC Output Current 350mA Constant Current Output Wattage 12W Max Dimming Function No Operating Temperature -40 ~ 60°C (-40 ~ 140°F) Weight 68g (0.15 lbs)
Constant Current
Dimensions L 5-1/4” (133mm), W 1-1/8” (29mm), H 7/8” (22mm)
Recommended Use 2-8 x 1W LEDs
Approval Dry locations. Approved to US and Canadian standards by CSA.
LED17W700D
Features UL Class 2, limited output and current with isolation for safe operation. Tight regulated output (1% line, 5% load) to maximize LED Code performance. AC Input Voltage 120V, 60Hz DC Output Voltage 7.8 ~ 24.6V DC DC Output Current 700mA Constant Current Output Wattage 17W Max Dimming Function No Operating Temperature -40 ~ 60°C (-40 ~ 140°F) Weight 136g (0.30 lbs)
Constant Current
Dimensions L 5-1/8” (130mm), W 1-3/8” (35mm), H 1” (25mm)
Recommended Use 2-6 x 2.5W LEDs
Approval Outdoor rated. Approved to US and Canadian standards by CSA. 66 Note: All drivers must be de-rated by 30%. For other configurations consult Recommended Drivers for LED Fixtures Tool online. http://mplighting.com/tools/FixtureToDriver/FixtureRecomDrivers.aspx
180 181
Drivers
LED25W1050 Code
Features UL Class 2, limited output and current with isolation for safe operation. Tight regulated output (1% line, 5% load) to maximize LED performance. AC Input Voltage 120V, 60Hz DC Output Voltage 5.6 ~ 24V DC
Non-Dimmable
DC Output Current 1.05A Constant Current Output Wattage 25.2W Max Dimming Function No Operating Temperature -40 ~ 60°C (-40 ~ 140°F) Weight 159g (0.35 lbs)
Constant Current
Dimensions L 3” (76mm), W 3-1/4” (83mm), H 1-3/8” (35mm)
Recommended Use 9, 12, 15, or 18 x 1W LEDs
Approval Dry locations. Approved to US and Canadian standards by CSA.
LED40W1750 Code
Features UL Class 2, limited output and current with isolation for safe operation. Tight regulated output (1% line, 5% load) to maximize LED performance. AC Input Voltage 120V, 60Hz DC Output Voltage 5.6 ~ 24V DC DC Output Current 1.75A Constant Current Output Wattage 40W Max Dimming Function No Operating Temperature -40 ~ 60°C (-40 ~ 140°F) Weight 272g (0.60 lbs)
Constant Current
Dimensions L 3” (76mm), W 3-1/4” (83mm), H 1-3/8” (35mm)
Recommended Use 15, 20, 25 or 30 x 1W LEDs
Approval Dry locations. Approved to US and Canadian standards by CSA.
TLDDLV6V6W1 Code
Features Compact size that maximizes design flexibility. 110, 220, 240 full range AC input. Tight regulated constant current output to maximize LED performance. AC Input Voltage 100 ~ 240V, 50/60Hz DC Output Voltage 6V Constant Voltage DC Output Current 0.02 ~ 1.00A Max Output Wattage 6W Max Dimming Function No Operating Temperature -20 ~ 60°C (-4 ~ 140°F) Weight 89.5g (0.20 lbs)
Constant Voltage
Dimensions L 2-5/8” (67mm), W 1-3/8” (35mm), H 7/8” (22mm)
Recommended Use L06 and L07 only
Approval Dry locations. Approved to US and Canadian standards by CSA.
Note: All drivers must be de-rated by 30%. For other configurations consult Recommended Drivers for LED Fixtures Tool online. http://mplighting.com/tools/FixtureToDriver/FixtureRecomDrivers.aspx
TLD12012V12W1 Code
Features UL Class 2, limited output and current with isolation for safe operation. Tight regulated output (1% line, 5% load) to maximize LED performance.
Drivers
www.mplighting.com
AC Input Voltage 120V, 50/60Hz DC Output Voltage 12V Constant Voltage
Non-Dimmable
DC Output Current 0.35 ~ 1.00A Max Output Wattage 12W Max Dimming Function No Operating Temperature -40 ~ 60°C (-40 ~ 140°F) Weight 136g (0.30 lbs)
Constant Voltage
Dimensions L 5-1/8” (130mm), W 1-3/8” (35mm), H 1” (25mm)
Recommended Use 2 x 3W fixtures
Approval Outdoor Rated. Approved to US and Canadian standards by CSA. 66
Code
Usage LED driver enclosures Finish Zinc plated Dimensions L 6-1/4” (160mm), W 5” (130mm), H 2” (51mm) Approval Dry locations.
5” 130mm
6-1/4” 160mm
EBX-260-ZP Code
Driver Enclosures
EBX-160-ZP
2” 51mm
Usage LED driver enclosures Finish Zinc plated Dimensions L 10-1/4” (260mm), W 5” (130mm), H 2-3/4” (71mm) Approval Dry locations.
5” 130mm
10-1/4” 260mm
2-3/4” 71mm
Note: All drivers must be de-rated by 30%. For other configurations consult Recommended Drivers for LED Fixtures Tool online. http://mplighting.com/tools/FixtureToDriver/FixtureRecomDrivers.aspx
182 183
Magnetic Low Voltage Transformers
TLW120M10 Code
Features Hard wired remote transformer. Dimmable with Magnetic Low Voltage Dimmers (ie. Lutron Diva). AC Input Voltage 120V, 60Hz AC Output Voltage 12V Output Wattage 10W Max Power Factor 95% Typical Efficiency 95% Dimming Function Yes (with Magnetic Low Voltage Dimmers) Operating Temperature -10 ~ 50°C (14 ~ 122°F) Weight 1.8kg (4 lbs) Dimensions Ø2-1/2” x 1-1/4” Approval Dry locations.
TLW120M300 Code
Features Comes with 6’ plug-in cord that can be field cut and hard wired. Dimmable with Magnetic Low Voltage Dimmers (ie. Lutron Diva). Integral push button circuit breaker. AC Input Voltage 120V, 60Hz AC Output Voltage 12V Output Wattage 300W Max Power Factor 95% Typical Efficiency 80% Dimming Function Yes (with Magnetic Low Voltage Dimmers) Operating Temperature -10 ~ 50°C (14 ~ 122°F) Weight 3.6kg (8 lbs) Dimensions L 5-1/4” (133mm), W 3-1/2” (89mm), H 3-1/4” (83mm) Approval Dry locations. Approved to UL by CSA/CUS.
TLW120MT150 TLW120MT300 Code
TLW277MT300 Code
Features Hard wired remote transformer. Dimmable with Magnetic Low Voltage Dimmers (ie. Lutron Diva). Integral push button circuit breaker. AC Input Voltage 277V, 60Hz AC Output Voltage 12V Output Wattage 300W Max Power Factor 95% Typical Efficiency 93% Dimming Function Yes (with Magnetic Low Voltage Dimmers) Operating Temperature -10 ~ 50°C (14 ~ 122°F) Weight 3.2kg (7 lbs) Dimensions L 3-1/8” (79mm), W 3-3/8” (86mm), H 7-1/8” (181mm) Approval Dry locations. UL Listed.
TLW120MT600 TLW277MT600 Code
Features Hard wired remote transformer. Dimmable with Magnetic Low Voltage Dimmers (ie. Lutron Diva). Integral push button circuit breaker. AC Input Voltage 120V / 277V, 60Hz
Magnetic Low Voltage Transformers
www.mplighting.com
AC Output Voltage 12V or 24V Output Wattage 600W Max Power Factor 98% Typical Efficiency 95% Dimming Function Yes (with Magnetic Low Voltage Dimmers) Operating Temperature -10 ~ 50°C (14 ~ 122°F) Weight 5.9kg (13 lbs) Dimensions L 4” (102mm), W 4-3/4” (121mm), H 7-7/8” (200mm) Approval Dry locations. UL Listed.
184
Recommended Driver Chart The following chart lists the recommended LED driver and fixture configurations to ensure optimal product performance and longevity. Simply locate the MP Lighting product from the left hand side of the chart to determine the recommended driver and fixture configuration. For example, the dimmable driver LED8W350i will perform best when used with 1-6 x 1W LED fixtures. Please note that the chart represents the most common applications; consult the online Recommended Drivers for LED Fixtures Tool for all other options. Drivers • All drivers must be de-rated by 30% • 350mA drivers must be used with 1W LEDs • 700mA drivers must be used with 2.5W LEDs Dimmable Drivers • Products are dimmable when a dimmable driver is specified • Dimmable drivers work on 0-10V dimming systems • Constant voltage drivers require dimming module #TLC010i
Constant Current
Constant Voltage
LED8W350i
LED20W700i
TLDAV60W9 + TLC010i
TLDAV60W12 + TLC010i
TLDAV100W15 + TLC010i
TLDAV100W20 + TLC010i
TLDAV100W24 + TLC010i
TLDAV100W4100 + TLC010i
L01 / L04
1W (1-6 fixtures)
2.5W (2-6 fixtures)
-
-
-
-
-
-
L02
1W (1-6 fixtures)
2.5W (2-6 fixtures)
-
-
-
-
-
-
L03
1W (1-6 fixtures)
2.5W (2-6 fixtures)
-
-
-
-
-
-
-
-
-
-
3 x 1W (1-2 fixtures)
3 x 2.5W (1-2 fixtures)
-
3 x 1W (1-12 fixtures), 3 x 2.5W (1-6 fixtures)
1W (1-6 fixtures)
2.5W (2-6 fixtures)
-
-
-
-
-
-
2 x 1W (1-3 fixtures)
2 x 2.5W (1-3 fixtures)
-
-
-
-
-
-
L21 / L22
1W (1-6 fixtures)
2.5W (2-6 fixtures)
-
-
-
-
-
-
L31 / L32 / L33 / L34
1W (1-6 fixtures)
2.5W (2-6 fixtures)
-
-
-
-
-
-
-
-
3.5W (2-12 fixtures), 6.5W (1-6 fixtures)
-
-
-
-
-
L05 L11 / L13/ L14 / L16 /L18 L12 / L15 / L17 / L19
L35 / L36 / L37 L51 / L52
1W (1-6 fixtures)
2.5W (2-6 fixtures)
-
-
-
-
-
-
L55 / L56 / L57
3 x 1W (1-2 fixtures)
-
-
3 x 1W (1-12 fixtures)
-
-
-
-
L58 / L64 / L65
-
2.5W (2-6 fixtures)
-
-
-
-
-
-
-
3.2W (2-10 fixtures)
-
-
-
-
-
-
12 x 1W (1 fixture ONLY)
-
-
-
-
12 x 1W (1-6 fixtures)
-
L73 (24V DC)
6 x 1W (1 fixture ONLY)
-
-
-
-
-
6 x 1W (1-12 fixtures)
-
-
4 x 2.5W (1 fixture ONLY)
-
-
4 x 2.5W (1-6 fixtures)
-
-
-
6 x 1W (1 fixture ONLY)
-
-
-
-
-
6 x 1W (1-12 fixtures)
-
L81
1W (1-6 fixtures)
2.5W (2-6 fixtures)
-
-
-
-
-
-
L85
-
-
3.5W (2-12 fixtures)
-
-
-
-
-
L75 L76 (24V DC)
L91 / L92
-
2.5W (2-6 fixtures)
-
-
-
-
-
-
L96
6 x 1W (1 fixture ONLY)
-
-
-
-
-
6 x 1W (1-12 fixtures)
-
L97 / L98
6 x 1W (1 fixture ONLY)
6 x 2.5W (1 fixture ONLY)
-
-
-
-
6 x 1W (1-12 fixtures), 6 x 2.5W (1-5 fixtures)
-
L99
-
12 x 1W (1 fixture ONLY)
-
-
-
-
12 x 1W (1-6 fixtures), 12 x 2.5W (1-2 fixtures)
-
L101 / L103 / L104 / L106
-
-
-
-
-
-
1W, S2 (12ft max.), S3 (18ft max.)
-
L102
-
-
-
-
-
-
0.07W, S28 (32ft max.), S56 (18ft max.)
-
L111
-
-
-
-
-
-
1W, S1 (6ft max.), S2 (8ft max.)
-
L112
-
-
-
-
-
-
-
2.5W, 4ft (1 driver needed) 2.5W, 8ft (2 drivers needed)
L121
-
-
-
-
-
-
0.07W, S1 (32ft max.), S2 (18ft max.), S3 (9ft max.)
-
L130 / L131
-
-
-
3 x 2.5 (1-6 fixtures)
-
-
-
-
-
-
-
L134
4 x 1W (1 fixture ONLY)
-
-
-
4 x 1W (1-18 fixtures), 4 x 2.5W (1-6 fixtures)
L135
4.5W (1 fixture ONLY)
-
-
9W (1-4 fixtures)
-
-
-
-
L141
-
-
-
-
-
13W (1-4 fixtures)
-
-
L142
-
-
-
9W (1-4 fixtures)
-
-
-
-
L151
3 x 1W (1-2 fixtures)
-
-
3 x 1W (1-12 fixtures)
-
-
-
-
L161
-
-
-
-
-
-
1W, 2" Spacing, 12ft max.
-
L171
-
-
-
-
-
-
1W, S2 (12ft max.), S3 (18ft max.)
-
L181
1W per arm (1-6 arms)
-
-
-
-
-
-
-
L191
0.07W, 2' (1 fixture ONLY)
0.07W, 4' (1 fixture ONLY)
-
-
-
-
0.07W, 2' (2-8 fixtures)
0.07W, 4' (2-4 fixtures)
L202
-
-
-
-
-
-
6 x 1W (1-12 fixtures)
-
-
-
-
4 x 2.5W (1 fixture ONLY)
-
-
4 x 1W (1-18 fixtures), 4 x 2.5W (1-6 fixtures)
6 x 1W (1 fixture ONLY)
-
-
-
-
-
6 x 1W (1-12 fixtures)
-
-
7 x 2.5W (1 fixture ONLY)
-
-
-
-
7 x 2.5W (1-4 fixtures)
-
G02L / G03L
6 x 1W (1 fixture ONLY)
-
-
-
-
-
6 x 1W (1-12 fixtures)
-
P71L / P81L / P82L (24V DC)
6 x 1W (1 fixture ONLY)
-
-
-
-
-
6 x 1W (1-12 fixtures)
-
L221
4 x 1W (1 fixture ONLY)
L222 (24V DC) L223 (24V DC)
Dimmable
3.2W (1 fixture ONLY)
L72 (24V DC)
L62
Recommended Driver Chart
www.mplighting.com
186 Note: All drivers must be de-rated by 30%. For other configurations consult Recommended Drivers for LED Fixtures Tool online. http://mplighting.com/tools/FixtureToDriver/FixtureRecomDrivers.aspx
188
Recommended Driver Chart
www.mplighting.com
Constant Current
Constant Voltage
LED3W350L
LED8W350L
LED9W700L
LED10W350D
LED17W700D
LED20W700i
TLDDLV6V6W1
TLDAV60W9
TLDAV60W12
TLDAV100W15
TLDAV100W24
TLDAV100W4100
L01 / L04
1W (1-2 fixtures)
-
2.5W (1-3 fixtures)
1W (2-7 fixtures)
2.5W (2-6 fixtures)
-
-
-
-
-
-
-
L02
1W (1-2 fixtures)
1W (2-7 fixtures)
2.5W (1-3 fixtures)
-
2.5W (2-6 fixtures)
-
-
-
-
-
-
-
L03
1W (1-2 fixtures)
-
2.5W (1-3 fixtures)
1W (2-7 fixtures)
2.5W (2-6 fixtures)
-
-
-
-
-
-
-
-
-
-
Non-Dimmable
L05
-
-
-
3W (1-2 fixtures)
3 x 2.5W (1-2 fixtures)
-
-
-
3.5W (2-12 fixtures), 7.5W (1-6 fixtures)
L06 / L07
-
-
-
-
-
-
0.1W (1-50 fixtures)
-
-
-
-
-
L51 / L52
1W (1-2 fixtures)
1W (2-7 fixtures)
2.5W (1-3 fixtures)
-
2.5W (2-6 fixtures)
-
-
-
-
-
-
-
L55 / L56 / L57
-
3 x 1W (1-2 fixtures)
-
-
-
-
-
-
3 x 1W (2-12 fixtures)
-
-
-
L58 / L64 / L65
-
-
2.5W (1-3 fixtures)
-
2.5W (2-6 fixtures)
-
-
-
-
-
-
-
L72 (24V DC)
-
-
-
-
12 x 1W (1 fixture ONLY)
-
-
-
-
-
12 x 1W (1-6 fixtures)
-
L73 (24V DC)
-
6 x 1W (1 fixture ONLY)
-
-
-
-
-
-
-
-
6 x 1W (1-12 fixtures)
-
L75
-
-
-
-
4 x 2.5W (1 fixture ONLY)
-
-
-
-
4 x 2.5W (1-6 fixtures)
-
-
L76 (24V DC)
-
6 x 1W (1 fixture ONLY)
-
-
-
-
-
-
-
-
6 x 1W (1-12 fixtures)
-
L81
1W (1-2 fixtures)
1W (2-7 fixtures)
2.5W (1-3 fixtures)
-
2.5W (2-6 fixtures)
-
-
-
-
-
-
-
L85
-
3.5W (1 fixture ONLY)
-
-
-
-
-
3.5W (2-12 fixtures)
-
-
-
-
L96 (24V DC)
-
6 x 1W (1 fixture ONLY)
-
-
-
-
-
-
-
-
6 x 1W (1-12 fixtures)
-
L97 / L98
-
6 x 1W (1 fixture ONLY)
-
-
6 x 2.5W (1 fixture ONLY)
-
-
-
-
-
6 x 1W (1-12 fixtures), 6 x 2.5W (1-5 fixtures)
-
L99
-
-
-
-
12 x 1W (1 fixture ONLY)
-
-
-
-
-
12 x 1W (1-6 fixture), 12 x 2.5W (1-2 fixture)
-
L101 / L103 / L104 / L106
-
-
-
-
-
-
-
-
-
-
1W, S2 (12ft max.), S3 (18ft max.)
-
L102
-
-
-
-
-
-
-
-
-
-
0.07W, S28 (32ft max.) S56 (18ft max.)
-
L121
-
-
-
-
-
-
-
-
-
-
0.07W, S28 (32ft max.), S56 (18ft max.), S112 (9ft max.)
-
L151
-
-
-
3 x 1W (1-2 fixtures)
-
-
-
-
3 x 1W (2-12 fixtures)
-
-
-
L161
-
-
-
-
-
-
-
-
-
-
1W, 2" Spacing, 12ft max.
-
L171
-
-
-
-
-
-
-
-
-
-
1W, S2 (12ft max.), S3 (18ft max.)
-
L181
-
1W per arm (2-7 fixtures)
-
-
-
-
-
-
-
-
-
-
L191
-
-
-
0.07W, 2' (1 fixture ONLY)
0.07W, 4' (1 fixture ONLY)
-
-
-
-
-
-
0.07W, 2' (2-8 fixtures), 0.07W, 4' (2-4 fixtures)
L202
-
6 x 1W (1 fixture ONLY)
-
-
-
-
-
-
-
-
6 x 1W (1-12 fixtures)
-
L221
-
4 x 1W (1 fixture ONLY)
-
-
4 x 2.5W (1 fixture ONLY)
-
-
-
-
4 x 1W (1-18 fixtures), 4 x 2.5W (1-6 fixtures)
-
-
L222 (24V DC)
-
6 x 1W (1 fixture ONLY)
-
-
-
-
-
-
-
6 x 1W (1-12 fixtures)
-
L223 (24V DC)
-
-
-
-
-
7 x 2.5W (1 fixture ONLY)
-
-
-
-
7 x 2.5W (1-4 fixtures)
-
G02L / G03L
-
6 x 1W (1 fixture ONLY)
-
-
-
-
-
-
-
-
6 x 1W (1-12 fixtures)
-
P71L / P81L / P82L (24V DC)
-
6 x 1W (1 fixture ONLY)
-
-
-
-
-
-
-
-
6 x 1W (1-12 fixtures)
-
189 191
Note: All drivers must be de-rated by 30%. For other configurations consult Recommended Drivers for LED Fixtures Tool online. http://mplighting.com/tools/FixtureToDriver/FixtureRecomDrivers.aspx
Lamp Index - LED The following technical data illustrates the attributes of our various LED sources. For more details refer to the IES files available through our website.
Source (W)
Current (mA)
0.07
20
0.1
20
0.5
CRI
Color Temp. (K)
Luminous Flux (lm)
75
2200
4.3
2700
4.6
3000
4.6
2700
1.3~3.8
2700
21.4~36
3000
21.4~36
3500
21.4~36
4100
21.4~36
2700
70~100
3000
70~100
3500
80~110
4100
80~110
2000
28.4~46.2
3000
60~100
2700
110~185
3000
125~200
3500
140~215
4100
140~215
2000
42.5
3000
95~170
3000
232
85
150
75
75 1
350 85
75 2.5
700 85
3.2
350
85
4100
255
3.5
350
85
3000
250
3.7
350
75
3000
200~280
4.5
350
80
3000
280~320
6.5
700
65
5000
720
85
3000
475
75
4100
560~648
80
3000
490~560
3000
960
5000
1110
9.5
700
13
700
85
Lamp Index & Isofootcandle Calculation
www.mplighting.com
Note: Due to the variation in LED manufacturing processes, the listed values of LED parameters are provided for guidance only.
Height Conversion Formula Polar Candela Distribution L18 1W, 30° 180° 3000K Std Height² Step57 1 lm Existing Mounting -90° 90° = Correction Factor New Mounting Height²
Isofootcandle Plot 2 0 1
Step 2
Correction Factor x Footcandle = New Mounting Height FC -45°
approx. 45° Note: Information is based on the most current data available; however, various operating -0° 275 cd factors such as reflectances and application type may cause differences between lab and max. -90° field results. Due to continuous improvements, specifications may change without notice. Consult www.mplighting.com for the most current information. 0°
2
1
0
1
2
3
20 10 0.5 0.1 fc
3 4 5
Mount height: 1 ft Total LLF: 1
190 191
Explanation of Symbols
Legend
Ingress Protection (IP) Rating System
Indoor/Dry Rated A dry rated location is an area, generally indoors, which is protected from exposure to excessive moisture and water.
This system provides a means of classifying the degrees of protection from dust and water afforded by electrical equipment and enclosures.
Outdoor - Damp Rated Damp rated locations are sheltered, outdoor areas that are protected from direct contact with rain, etc.
First Digit indicates the level of protection against solid objects. Level Protected Against
Effective Against
Outdoor - Wet Rated Wet rated locations are unsheltered, outdoor areas that are exposed to direct contact with rain, etc.
0
—
No protection against contact and ingress of objects.
Ceiling Fixture Suitable for ceiling applications.
1
>2” (50mm) object size
Any large surface of the body, such as the back of a hand, but no protection against deliberate contact with a body part.
2
>1/2 ” (12.5mm) object size Fingers or similar objects.
3
>3/32” (2.5mm) object size Tools, thick wires, etc.
4
>1/32” (1mm) object size
Most wires, screws, etc.
5
Dust protected
Ingress of dust is not entirely prevented, but it must not enter in sufficient quantity to interfere with the satisfactory operation of the equipment; complete protection against contact.
6
Dust tight
No ingress of dust; complete protection against contact.
Floor Fixture Suitable for floor applications.
Wall Fixture Suitable for wall applications.
Insulated Ceiling Fixture
Non-Insulated Ceiling Fixture
Submersible Fixture Suitable for underwater applications.
Second Digit indicates the level of protection against liquids.
Rail System Fixture can be mounted to MP rail systems. (See pages 136-143 for hardware options).
Level Protected Against
Details
Linear System Fixture can be ceiling or wall mounted as part of a linear system application. (See pages 144-146 for hardware options).
0
Not protected
—
1
Dripping water
Dripping water (vertically falling drops) shall have no harmful effect.
Cabinet Mounted Fixture Suitable for showcase, kitchen cabinet and millwork applications.
2
Dripping water when tilted up to 15°
Vertically dripping water shall have no harmful effect when the enclosure is tilted at an angle up to 15° from its normal position.
3
Spraying water
Water falling as a spray at any angle up to 60° from the vertical shall have no harmful effect.
4
Splashing water
Water splashing against the enclosure from any direction shall have no harmful effect.
5
Water jets
Water projected by a nozzle against enclosure from any direction shall have no harmful effects.
6
Powerful water jets
Water projected in powerful jets against the enclosure from any direction shall have no harmful effects.
7
Immersion up to 3’-15/16” (1m)
Ingress of water in harmful quantity shall not be possible when the enclosure is immersed in water under defined conditions of pressure and time (up to 3’-15/16” (1m) of submersion).
8
Immersion beyond 3’-15/16” The equipment is suitable for (1m) continuous immersion in water under conditions which shall be specified by the manufacturer.*
Dimmable from 0~10V
Non-Dimmable
IP Rating (See opposite column for further details). 66 Constant Current Driver
Constant Voltage Driver
MP Integrating Sphere Tested
*Normally, this will mean that the equipment is hermetically sealed. However, with certain types of equipment, it can mean that water can enter but only in such a manner that produces no harmful effects.
Canopy Mounts
Low-Voltage Rails Systems
C1C Ø2-3/8” x 1/4” (Ø60mm x 6mm) canopy Mounts to custom 2” x 2” octagonal box (included) with screws.
DC Dual circuit rail 12V/24V MP Lighting rail system (See pages 165-167 for hardware options).
C1M Ø2-3/8” x 1/4” (Ø60mm x 6mm) canopy Retrofit to existing standard octagonal box using custom mounting plate (included) with screws.
SR Single rail 12V/24V MP Lighting rail system (See pages 160-164 for hardware options).
C2C 2-5/8” Sq. x 3/8” (67mm Sq. x 10mm) canopy Mounts to custom 2” x 2” octagonal box (included) with screws.
SF Single rail flush wall 12V/24V MP Lighting rail system (See pages 160-164 for hardware options).
C2M 2-5/8” Sq. x 3/8” (67mm Sq. x 10mm) canopy Retrofit to existing standard octagonal box using custom mounting plate (included) with screws.
Caution A 24V LED driver must be used as the power supply. Using a traditional low-voltage 12V transformer to power the system will not work and will damage the LEDs.
C3 Ø4-5/8” x 1/4” (Ø117mm x 6mm) canopy Mounts to standard octagonal box (not included).
120V Track System
C4 4-5/8” Sq. x 1/4” (117mm Sq. x 6mm) canopy Mounts to standard J-box (not included).
3CT 3-circuit track Easy to position and tighten. Installs on MP Lighting 3-circuit track (sold separately). 3-circuit switch selectable (circuit 1,2,3 or off). Low profile. Positive locking.
Mounting & Finishing Options
www.mplighting.com
C7 Ø6-5/16” x 2-3/8” (Ø160mm x 60mm) canopy Mounts to standard octagonal box (not included).
C9 Ø4-13/16” x 11/16” (Ø122mm x 17mm) canopy Mounts to standard octagonal box (not included).
1CT 1-circuit track Easy to position and tighten. Installs on most 1-circuit track systems including Lightolier, Halo, Juno and 2-Wire.
Others Wall Mounts W1CB Ø2-3/8” x 1/4” (Ø60mm x 6mm) canopy Mounts to custom 2” x 2” octagonal box (included) with screws.
MB Ø1-5/8” (Ø41mm) mounting bracket Bracket mounts to ceiling or wall.
Finishing Options
(not all options are available for every product) W1MP Ø2-3/8” x 1/4” (Ø60mm x 6mm) canopy Retrofit to existing standard octagonal box using custom mounting plate (included) with screws.
BA = black anodized BK = powder coated black BN = brushed nickel
W2CB 2-5/8” Sq. x 3/8” (67mm Sq. x 10mm) canopy Mounts to custom 2” x 2” octagonal box (included) with screws.
BZ = bronze MA/MC = matte chrome MP = matte pewter
W2MP 2-5/8” Sq. x 3/8” (67mm Sq. x 10mm) canopy Retrofit to existing standard octagonal box using custom mounting plate (included) with screws. W3 Ø4-5/8” x 1/4” (Ø117mm x 6mm) canopy Mounts to standard octagonal box (not included).
S = silver S3 = 303 stainless steel S6 = 316 stainless steel WH = white ZP = zinc plated
WK Ø2” x 3/4” (Ø51mm) wall hook Comes with 6-7/8” (175mm) standard vertical stem.
Custom finishes are available for some fixtures. Please contact factory for custom finish inquiries or requests.
192 193
Online with MP Lighting
Our Website MP Lighting’s website is designed to simplify the specification, sales, and order process for our valued agents and customers. It features an easy-to-use navigation menu and an extensive range of tools to allow users to quickly browse the site and obtain useful product information. Agents and customers can view product lines and application images, download specification sheets and literature, or access price lists and marketing materials. Available tools include a wire length calculator, recommended driver tool, downloadable Revit files, online order tracking, and online payment options. Visit us at www.mplighting.com to learn more about the features we have to offer.
Useful Tools MP Lighting’s website features a Wire Length Calculator tool and Recommended Driver for LED Fixtures tool as a value-added benefit to our customers: Wire Length Calculator – The Wire Length Calculator for LED products allows users to calculate the maximum wire length (voltage drop) by entering a few specifications about the product and wire type. To determine the overall length of wire that can be used, follow these instructions:
Recommended Driver for LED Fixtures – The Recommended Drivers for LED Fixtures tool is a simple, step-by-step tool that allows users to choose the correct driver based on fixture(s), driver type, and connection. To determine the recommended driver(s), follow these instructions:
Instructions 1) Enter the Load Current (mA) and the Voltage (V) of the fixture in the appropriate text box. Instructions about how to find and/or calculate the Load Current and Voltage are available with the Wire Length Calculator tool.
Instructions 1) Select a fixture from the drop down list.
2) Choose the appropriate Gauge, Maximum Voltage Drop, and System from the drop down list.
3) Select Non-Dimmable or Dimmable Driver Type and the recommended driver(s), output current/ voltage, AC input voltage, description, and driver image will be displayed.
2) Select the correct current for the fixture (if applicable).
3) Click ”Get Length” button and the wire length will be displayed. Please note that the length of wire calculated is the overall wire length that can be used for that specific fixture(s). The actual length of wire can be adjusted depending on the situation or application.
Revit MP Lighting's website now features a library of Revit Family Files for several LED fixtures. Users will be able to download a 3D Revit File and insert it into their architectural or mechanical documents. Each Revit Family File will include photometric data and related specifications, allowing architects and designers to view the MP product, along with its projected light levels, in their architectural renderings or BIM projects. To access the Revit Family Files, visit our website and choose “Support - REVIT Library” from the home page menu for a list of products. You can also choose the appropriate fixture from the “Products” menu (example L98) and then choose “Revit Modeling Download” from the “Downloads” menu on the right hand side of the page.
For fixtures connected in series, a diagram showing the minimum and maximum amount of fixtures is also shown. For additional product information, users can click on the driver product code, LED driver image, or LED Dimming Control to be directed to the web page or specification sheet.
Research & Development MP Lighting has recently expanded our Research & Development Lab to include new equipment for LED product testing and CSA Certification. With the recent push by government agencies for buildings to meet strict energy codes, it is even more important to ensure that MP products are tested for reliability and performance. The new equipment will ensure that product specifications are accurate and up-to-date. 1) The new LED Tester, produced by a leading German manufacturer of integrating spheres, measures the color temperature, color rendering index, and light flux in lumens for LED fixtures. The unique spherical shape and diffuse reflecting surface allow the light to reflect completely and evenly, measuring the fixture's light output in all directions. 2) The Konica Minolta CL-200A Incident Color Meter measures the color temperature and amount of light hitting a surface. This light meter is highly reliable in measuring the color temperature of white LEDs as it has the ability to measure the chromaticity and quality of light output from an assembled product. The addition of this equipment to our R&D Lab will also ensure that new products and product modifications meet or exceed industry standards, such as Energy Star and CSA Certification.
Research & Development
www.mplighting.com
LED luminaire testing for MP Lighting products is performed according to LM-79 Standards, based on the Electrical and Photometric Measurements of Solid State Lighting Products. The standards illustrate approved methods in describing procedures and precautions when performing reproducible measurements of LED products. The actual light of the luminaire of interest is measured directly from the complete luminaire using an integrating sphere system. Test results include total flux, electrical power, efficacy (lm/W), and chromaticity. Tests are performed at the environment temperature. Measurement conditions and techniques are subject to change.
194 195
Terms & Warranty
Terms for Sales
Warranty
Net 30 days with prior approved credit otherwise a 50% deposit with order and the balance in full prior to shipping. A service charge of 2% per month, compounded monthly, will be added to all past due amounts, except where prohibited by law. For credit applications, contact Accounts Receivable.
One year limited warranty - Low Voltage and Line Voltage Systems. Three year limited warranty - LED products and drivers. Note: Lamps are not covered by warranty.
Pricing See separate price list. All prices are retail prices and do not include shipping, handling, taxes, or installation. Prices are subject to change without notice and we reserve the right to correct errors. Please contact MP Lighting for details. Minimum Order Charge A Service Charge of $25.00 will be added to all original customer orders less than $100.00 net. Freight Freight is not included. Prepaid and charge shipping costs are Freight Company’s quoted estimates PLUS 15% administration fee to cover any shipping charge overruns, brokerage, customs charges and handling fees. This is non-negotiable and non-refundable. To avoid this fee, customers may provide their own courier or freight account number and will be responsible for additional charges from US customs. Shipping raw materials or replacement parts outside Canada may incur duty charges and/or taxes. Duty charges are calculated as $25.00 (fixed) plus 12% of the valued of the parts purchased. Cancellations Cancellation of orders must be made by fax or email without delay and may be subject to restocking, service and other fees. All orders that are in progress or completed, and are cancelled by the customer will be subject to a minimum 25% restocking charge. Quote Assistance MP Lighting does not guarantee the availability of any item listed and reserves the right to discontinue or change the technical or design specifications of its products at any time without notice. To ensure accuracy and expedite your order, please order by part#. Quote requests may be faxed to 604-708-1179 but will not be accepted over the phone. If you do not see what you’re looking for, please inquire. Our representatives and in-house design team can assist you with your specifications. Allow longer lead time for custom quoted items. Quotes are valid for 3 months from date of issue. Return Policy Return requests must be made within 60 days of the receipt of goods and require an RGA (Return Goods Authorization) number. Returns without an RGA will be refused and returned at your expense. MP Lighting will only accept the return of uninstalled products that are in saleable condition and are free of damages, scratches, and alterations. RGA numbers can be obtained by fax request at 604-708-1185 Attention: Customer Service, or by email request at rga@mplighting.com. All returns are subject to a minimum 25% restocking fee. We will not accept returns on custom orders* or purchase overruns. Goods must be returned prepaid with RGA numbers clearly marked on returning packages. RGA’s are valid for 30 days from issue date to the time products are received at our factory. Expired RGA’s will be refused and returned at your expense. Credit will be issued at the sole discretion of MP Lighting. No credit will be issued on defective products due to improper installation or misuse. *Custom Orders Custom Orders are defined as any product or products which are not included in our literature or are defined as ‘X’ in our literature. Custom orders may include, but are not limited to, irregular track lengths and off-site work, such as metal fabrications or custom colors. A 50% non-refundable deposit is required for all custom orders. Custom orders cannot be cancelled after Release of Order. Custom material cannot be returned except for defects proven to be the manufacturer’s responsibility.
MP DESIGN INC. (hereinafter referred to as “MP Lighting”) gives the following warranty for each new MP Lighting product distributed in Canada and the United States by MP Lighting and sold through an authorized MP Lighting Distributor. MP Lighting warrants that all products manufactured by MP Lighting to be free from defects in materials and workmanship under normal use subject to the following terms and conditions: Conditions 1. Parts and Labor: One year from date of original purchase from distributor for low voltage and line voltage systems. Three years from date of original purchase from distributor for LED products. 2. Limitation: MP Lighting systems are approved to CSA & UL standards when used as a complete system. Substituting another manufacture’s product will void all approvals and will remove MP Lighting from any liability. Malfunction and damage to product due to improper installation or misuse will not be covered under warranty. 3. Receipt of Goods: All products are assembled, tested and double checked for accuracy before being shipped to customer. It is the responsibility of the consignee receiving the goods to inspect the goods to ensure accuracy of order and to check for any damages that could have occurred from shipping. Claims for missing parts must be made within 5 business days from receipt of goods. Claims for missing parts after 5 days will not be accepted. Damaged to product due to shipping should be claimed immediately with freight carrier. MP Lighting is not responsible for product damaged in transit by freight carrier. 4. Proof of Purchase: This warranty applies to the product from original date of purchase from distributor. The customer must furnish proof of original invoice, packing slip or payment. 5. Subject Product: This warranty covers the following products– • Monospot Fixtures • Cable Systems • Single Rail Systems • Single Rail Flush Wall Systems • Horizontal Double Rail Systems • Vertical Double Rail Systems • Dual Circuit Rail Systems • 1-Circuit Track Systems • 3-Circuit Track Systems • Line Voltage Systems • LED Products 6. Disclaimer or Consequential Damage: This warranty covers only the product itself, we assume no liability for labor costs, installation costs, improper fixture selections or other losses. Product returned for Warranty inspection must be given an RGA (Return Goods Authorization) from MP Lighting. Products must be returned freight prepaid with the RGA number clearly marked on the outside of the box. Upon confirmation of a defect or failure, at our discretion, we will repair or replace the item. If product is deemed to be in good working condition or if any of the above mentioned conditions are not met, the product will be returned and no warranty will be given. RGA numbers may be obtained by fax request at 604-708-1185 Attention: Customer Service, or by email request at rga@ mplighting.com. Approval MP Lighting systems are Approved to US and Canadian standards by CSA.
Code Page
Code Page
Code Page
Code Page
Code Page
3CT 171
CPY052 168
L37 55
L181B 81
SDF063 170
3CT101 171
CPY053 168
L51 83
L181M 81
SDF064 170
3CT201 171
CPY054 169
L52 85
L181T 81
SDF065 170
3CT202 171
CPY055 169
L55 87
L191 125
SDF070
3CT301 171
EBX-160-ZP 183
L56 89
L200 157
SDF071 168
3CT401 171
EBX-260-ZP 183
L57 91
L202 121
SLD-100W 168
3CT501 172
END001 160
L58 93
L203 159
SLD-DC 167
3CT502 172
END004 165
L59 95
L221 111
SLD-SR 164
3CT601 172
END011 162
L62 97
L222 113
TLC010i 179
3CT602 172
G02L 127
L64 99
L223 115
TLD12012V12W1 183
3CT603 172
G03L 129
L65 101
LED3W350L 180
TLDAV60W9 177
3CT604 172
JON001 162
L72 103
LED8W350i 176
TLDAV60W12 178
3CT701 172
JON002 162
L73 105
LED8W350L 180
TLDAV100W12 178
3CT801 173
JON003 162
L75 107
LED9W700L 180
TLDAV100W15 178
3CT901 173
JON004 162
L76 109
LED10W350D 181
TLDAV100W20 179
3CT1001 173
JON005 165
L81 117
LED12W350 181
TLDAV100W24 179
3CT1201 173
JON006 165
L85 119
LED17W700D 181
TLDDLV6V6W1 182
3CT1202 173
L01 7
L91 57
LED20W700i 176
TLDDLV60W5000 177
3CT3001 174
L02 9
L92 59
LED25W1050 182
TLDDLV100W4100 177
3CTPWB 171
L03 11
L96 123
LED25W1050i 176
TLW120M10 184
ACCS-BE
175
L04 13
L97 61
LED40W1750 182
TLW120M300 184
ACCS-CS
175
L05 15
L98 63
P71L 131
TLW120MT150 184
ACCS-ELB
175
L06 17
L99 65
P81L 133
TLW120MT300 184
ACCS-LB
175
L07 19
L101 137
P82 L
135
TLW120MT600 185
ACCS-LH
175
L11 21
L102 139
RAL001 160
TLW277MT300 185
ACCS-LM
175
L12 23
L103 141
RAL004 165
TLW277MT600 185
ACCS-MS
175
L13 25
L104 143
RAL181 81
ACCS-SH
175
L14 27
L106 145
SDF010 160
ACCS-SHB
175
L15 29
L111 147
SDF011 160
CPY010 163
L16 31
L112 149
SDF012 160
CPY011 163
L17 33
L121 151
SDF013 160
CPY012 163
L18 35
L130 67
SDF014 161
CPY013 163
L19 37
L131 69
SDF015 161
CPY015 164
L21 39
L134 71
SDF016 161
CPY016 164
L22 41
L135 73
SDF040 165
CPY018 164
L31 43
L141 75
SDF041 165
CPY041 166
L32 45
L142 77
SDF042 165
CPY043 166
L33 47
L151 79
SDF045 166
CPY044 166
L34 49
L161 153
SDF060
169 & 174
CPY050 173
L35 51
L171 155
SDF061
169 & 174
CPY051 173
L36 53
L181 81
SDF062 169
Index
www.mplighting.com
168 & 174
196 Please Recycle
197
16 West 4th Avenue Vancouver BC V5Y 1G3 Canada t 1 877 708 1184 (toll free) t 604 708 1184 f 604 708 1185 sales@mplighting.com www.mplighting.com Copyright 2012 Š MP Lighting. The information in this book is subject to change without notice. Printed in Canada.
01-2012