Sup r stud

Page 1

Mechanical Anchoring Systems

Sup-R-Stud® + Sup-R-Stud® + Available Materials • Carbon steel, zinc plated • Carbon steel, mechanically galvanized Class 65 • Grade 5, yellow di-chromated • 303/304 stainless steel • 316 stainless steel Features/Advantages • Required hole diameter equals anchor diameter • Excellent for setting immediately • Can be loaded immediately • Can be set in a bottomless hole • Simple installation • Nut and washer supplied in package • ROHS compliant except for Grade 5 Concerns • Do not use in brick or block • Not advised for use where vibratory loads are high • Oversize holes are detrimental and will reduce load performance

Anchor Spacing / Edge Distance Anchor Diameter

Approvals/Listings • G.S.A. Spec FF-S-325C, Group II, Type 4, Class 1 • ICC ESR-3235 3/8, 1/2, 5/8, C-STL, ZP • Contact customer service for approvals / listings for state D.O.T.’s • Metro Dade NCA No: 10-0928.01

Min. Anchor Spacing *

1/4”

2-1/2”

1-1/4”

3/8”

3-3/4”

1-7/8”

1/2”

5”

2-1/2”

5/8”

6-1/4”

3-1/8”

3/4”

7-1/2”

3-3/8”

7/8”

8-3/4”

4-3/8”

1”

10”

5”

1-1/4”

12-1/2”

6-1/4”

* To obtain 100% load

Made in USA

Step 1: Select the correct diameter drill bit, drill a hole to minimum required hole depth or deeper.

Step 2: Remove drilling debris from the bottom of the drill hole using a blowout bulb, compressed air or vacuum.

Step 3: Assemble the nut & washer past the impact end of the SRS+. Use a hammer to tap the anchor through the part being fastened into the drilled hole until the washer is in contact with the part

Step 4: Using a torque wrench, apply the specified installation torque.

12

Min. Edge Distance *


Mechanical Anchoring Systems

Sup-R-Stud® + Sup-R-Stud® +

Made in USA Order Detail *Sizes made to order. Carbon Steel Anchor Diameter & Length

Order Code

1/4” x 1-1/2” 1/4” x 1-3/4” 1/4” x 2-1/4” 1/4 “x 3-1/4”

2614TIE 2614134 2614214 2614314

3/8” x 2-1/4” 3/8” x 2-3/4” 3/8” x 3” 3/8” x 3-3/4” 3/8” x 5”

Galvanized

Thread Length

303/304 Stainless

316 Stainless

Grade 5 Steel Hole Diameter

Length ID

Max Thk Mat to be Anchored

— 7/8" 1-3/8" 2-1/4"

1/4" 1/4" 1/4" 1/4"

— A B D

— 3/8" 7/8" 1-7/8"

— 8-10 8-10 8-10

100 100 100 100

800 800 800 800

2538214 2538234* 2538300 2538334 2538500

1-3/16" 1-5/8" 1-7/8" 2-5/8" 4"

3/8" 3/8" 3/8" 3/8" 3/8"

B C D E H

1/4" 3/4" 1" 1-3/4" 3"

15-30 15-30 15-30 15-30 15-30

50 50 50 50 50

400 400 400 400 250

1-1/2" 2-1/2" 3" 4" 1-1/4" 1-1/4"

2512234 2512334* 2512414 2512512 2512700 2512812

1-1/2" 2-1/2" 3" 4" 1-1/4" 1-1/4"

1/2" 1/2" 1/2" 1/2" 1/2" 1/2"

C E F I L O

1/8" 1" 1-1/2" 2-3/4" 4-1/4" 5-3/4”

25-50 25-50 25-50 25-50 25-50 25-50

50 50 50 50 25 25

150 150 150 150 75 75

275831S* 275841S* 275850S 275860S* 275870S* 275881S* 275810S*

1-5/8" 2-5/8" 3-1/4" 4-1/8" 1-1/2" 1-1/2" 1-1/2"

2558312 2558412 2558500 2558600 2558700 2558812 2558100*

1-5/8" 2-5/8" 3-1/4" 4-1/8" 1-1/2" 1-1/2" 1-1/2"

5/8" 5/8" 5/8" 5/8" 5/8" 5/8" 5/8"

E G H J L O R

1/8" 1-1/8" 1-5/8" 2-5/8" 3-5/8" 5-1/8" 6 5/8"

40-75 40-75 40-75 40-75 40-75 40-75 40-75

25 25 25 25 20 20 25

75 75 75 75 60 60 50

2-3/8" 2-7/8" 3-5/8" 4-1/4" 2" 2" 2" 2"

273441S* 273443S 273451S 273461S* 273470S* 273481S* 273410S* 273412S*

2-3/8" 2-7/8" 3-5/8" 4-1/4" 2" 2" 2" 2"

2534414 2534434 2534512 2534614* 2534700 2534812* 2534100 2534120*

2-3/8" 2-7/8" 3-5/8" 4-1/4" 2" 2" 2" 2"

3/4" 3/4" 3/4" 3/4" 3/4" 3/4" 3/4" 3/4"

F G I J L O R T

1/8" 5/8" 1-3/8" 2-1/8" 2-7/8" 4-3/8" 5-7/8" 7-7/8"

100-200 100-200 100-200 100-200 100-200 100-200 100-200 100-200

25 25 20 20 15 15 15 15

75 75 60 60 45 45 30 30

2778600* 2778800* 2778100*

2-1/4" 2-1/4" 2-1/4"

277860S* 277880S* 277810S*

2-1/4" 2-1/4" 2-1/4"

2578600 2578800 2578100

2-1/4" 2-1/4" 2-1/4"

7/8" 7/8" 7/8"

J N R

1-1/8" 3-1/8" 5-1/8"

125-225 125-225 125-225

10 10 10

30 30 20

3-1/2" 4" 4"

2716000 2719000 2711200

2-1/4" 2-1/4" 2-1/4"

271600S* 271900S* 271120S*

2-1/4" 2-1/4" 2-1/4"

2516000 2519000 2511200*

2-1/4" 2-1/4" 2-1/4"

1" 1" 1"

J P T

1/2" 3-1/2" 6-1/2"

150-250 150-250 150-250

10 10 10

30 20 20

3-1/4" 3-1/4"

2711490* 2711412*

3-1/4" 3-1/4"

271149S* 271141S*

3-1/4" 3-1/4"

2511490 2511412

3-1/4" 3-1/4"

1-1/4" 1-1/4"

P T

1-1/4" 4-1/4"

200-350 200-350

5 5

15 10

Order Code

Thread Length

Order Code

Thread Length

Order Code

Thread Length

Order Code

— 7/8" 1-3/8" 2-1/4"

— 2814134 2814214 2814314

— 7/8" 1-3/8" 2-1/4"

— 2714134 2714214 2714314

— 7/8" 1-3/8" 2-1/4"

— 271413S 271421S 271431S*

— 7/8" 1-3/8" 2-1/4"

— 2514134 2514214 2514314

2638214 2638234 2638300 2638334 2638500

1-3/16" 1-5/8" 1-7/8" 2-5/8" 4"

2838214 2838234 2838300 2838334 2838500

1-3/16" 1-5/8" 1-7/8" 2-5/8" 4"

2738214 2738234 2738300 2738334 2738500

1-3/16" 1-5/8" 1-7/8" 2-5/8" 4"

273821S* 273823S* 273830S 273833S 273850S*

1-3/16" 1-5/8" 1-7/8" 2-5/8" 4"

1/2” x 2-3/4” 1/2” x 3-3/4” 1/2” x 4-1/4” 1/2” x 5-1/2” 1/2” x 7” 1/2” x 8-1/2”

2612234 2612334 2612414 2612512 2612700 2612812

1-1/2" 2-1/2" 3" 4" 4" 4"

2812234 2812334 2812414 2812512 2812700 2812812

1-1/2" 2-1/2" 3" 4" 4" 4"

2712234 2712334 2712414 2712512 2712700 2712812*

1-1/2" 2-1/2" 3" 4" 1-1/4" 1-1/4"

271223S 271233S* 271241S 271251S* 271270S* 271281S*

5/”8 x 3-1/2” 5/8” x 4-1/2” 5/8” x 5” 5/8” x 6” 5/8” x 7” 5/8” x 8-1/2” 5/8” x 10”

2658312 2658412 2658500 2658600 2658700 2658812 2658100

1-5/8" 2-5/8" 3-1/4" 4-1/8" 4" 4" 4"

2858312 2858412 2858500 2858600 2858700 2858812 2858100

1-5/8" 2-5/8" 3-1/4" 4-1/8" 4" 4" 4"

2758312 2758412* 2758500 2758600 2758700* 2758812* 2758100*

1-5/8" 2-5/8" 3-1/4" 4-1/8" 1-1/2" 1-1/2" 1-1/2"

3/4” x 4-1/4” 3/4” x 4-3/4” 3/4” x 5-1/2” 3/4” x 6-1/4” 3/4” x 7” 3/4” x 8-1/2” 3/4” x 10” 3/4” x 12”

2634414 2634434 2634512 2634614 2634700 2634812 2634100 263412T

2-3/8" 2-7/8" 3-5/8" 4-1/4" 4" 4" 4" 4"

2834414 2834434 2834512 2834614 2834700 2834812 2834100 283412T

2-3/8" 2-7/8" 3-5/8" 4-1/4" 4" 4" 4" 4"

2734414 2734434 2734512 2734614* 2734700 2734812 2734100 2734120*

7/8” x 6” 7/8” x 8” 7/8” x 10”

2678600 2678800 2678100

3-1/2" 4" 4"

2878600 2878800 2878100

3-1/2" 4" 4"

1” x 6” 1” x 9” 1” x 12”

2616000 2619000 2611200

3-1/2" 4" 4"

2816000 2819000 2811200

1-1/4” x 9” 1-1/4 x 12”

2611490 2611412

3-1/4" 3-1/4"

2811490 2811412

Step 1: Select the correct diameter drill bit, drill a hole to minimum required hole depth or deeper.

Thread Length

Required Torque to Set (ft. lbs.)

Step 2: Remove drilling debris from the bottom of the drill hole using a blowout bulb, compressed air or vacuum.

Step 3: Assemble the nut & washer past the impact end of the SRS+. Use a hammer to tap the anchor through the part being fastened into the drilled hole until the washer is in contact with the part

Step 4: Using a torque wrench, apply the specified installation torque.

13

Box Quantity.

Master Quantity.


Turn static files into dynamic content formats.

Create a flipbook
Issuu converts static files into: digital portfolios, online yearbooks, online catalogs, digital photo albums and more. Sign up and create your flipbook.