ARDEN PRO GU10 DOWNLIGHTER INSTRUCTIONS
Issue 01 18th May 2023
THANK YOUfor buying this product. To helpensure it gives complete satisfaction pleaseinstall it according totheseinstructions and then pass the instructions to theappropriateperson for retention and futurereference.
SAFETY This is amains powered product. It is designedto beinstalled by suitably qualifiedpersonnel only and in accordance with theapplicable buildingand electrical regulations. Beforeinstallation ormaintenance, the electrical supply to the product must beisolated.
INSTALLATIONSUPPORT If installation advice or accessories are required, pleasecontact us at theaboveaddress. We will do our best to help. When reporting asuspectedfault, orseekinginstallationsupport theproblem is likely tobe resolved most quickly if you have full product details to-hand, as well as details of when and where it was purchased.
DIMENSIONS
INSTALLATION–TORSIONSPRINGS AS STANDARD
1. Decide mounting position inceiling & cut thehole. Care shouldbe taken when cuttingthe holeto avoid structures & to not exceedthe specifiedcutting diametersoas not toexposethecut edge.
2. Providemains cable(s) downthrough the mounting hole& route to the luminaire.
3. Unclipthe terminal cover to expose theterminal block. Terminate the mains supply ensuringcorrect polarity is observed.
4. Ratchet down thecableclamps torestrainthe mains supply cable(s). Note: Theclamps should belocated on the outer insulation. Then refit theterminal cover by snapping into place.
5. Torsionsprings are fittedas standard to thelowerstep of the metalplates (3 positions are available).
6. If adjustment tothecorrect mounting height positionis required tosuit theceilingthickness thetorsionsprings canbe removed and relocated to the other positions:
a. Compress thesprings tounhook them and remove
b. Then Locateto the required position
c. Pushtheside of thecoiledspringwith thesmallleg ontothechosennotch position, locatingthesmall leg behind the notch below. Then pushtocompress the coiled part of the spring toallow the opposingsideto locateonto the notch.
d. Repeat for opposite side.
7. Locate intoceilingby pushing up& holding bothsprings upwards, locate through themountinghole, then releaseto allow the canto be pulled up tothemountingsurface.
ALTERNATIVE FIXING USINGTHE SWING OUT SUSPENSION ARMS
1. Removethe torsionsprings as 6a. above.
2. Removethe front bezel by pulling it away fromthemainbody can. This will exposethelampholder& swing out suspension arms securingscrews.
3. Select thecorrect format of suspension arm tosuit theceilingthickness:
For 0-30mm thickness leavethe Z brackets inposition.
For 30-60mm thickness, removethe Z bracket part by undoing thesmall pozi drivescrew onboth arms.
4. Insert theconnectionbox upthrough the holeintothe ceilingvoid.
5. Insert themain body can upthrough the hole, thensecure by:
Locatingthescrew head of one ofthe twoswingout suspensionarms
Insert a Torx 10driver& rotate clockwiseto get the armtoswing out from the side of thebody
Keep rotating thescrew headto lower it & clamptothetop of theceiling surface. Care shouldbetakennot toovertighten& causedamageto theceiling material
Repeat forsecondsuspension arm.
INSERT YOUR CHOSENGU10LED LAMP BY:
1. Removethe front bezel by pulling it away fromthemainbody can
2. Insertingthepins of the GU10 LED lamp intotheflying lampholder& rotateclockwisetosecure.
3. Clip thefront of the lamp intothe front bezel using thespringclip provided.
4. Carefully relocatefront bezel& push to back into to main body canto secure. Makesurethespringclips onthe front bezel align withthe moulded teeth insidethe body.
5. Tilt thelamp headto required direction.
6. Withthe down lighter installed, reconnect powersupply &check forcorrect operation. Notethat insulation resistance tests may cause irreparable damage tothe lamp.
NOTES
1. If mountingtheluminaire externally then theExternalversion shouldbe used. This will have /EXT inthe product code.
2. The IP44 ratingis totherear of the product. Thefront is IP20 rated.
3. This product canbe installed ininsulation providedthelamp usedismax. 7.5WLED