Model 60000-0000 60000-0024 Full 8-way Control Pad On/Off; Spot/Flood Switching
FEATURES
• Adds wireless control to existing searchlight installations for both console and remote control operation.
• Can be installed for wireless-only operation.
Grip Strip
• 12/24 volt operation (60000-0000/60000-0024).
LED Signal Transmission Indicator (Battery Check)
• True 8-way directional control with instant response for precise targeting. • “On/off” and “spot/flood” selection (for applicable models) plus LED battery check. • Long life lithium battery for hand-held remote control. • Meets all applicable regulatory requirements for FCC, Industry Canada, Australian and European compliance. • “First-on” learning mode syncs transmitter and receiver codes for no cross-talking with other remote control devices. • Up to four wireless remote units can be used per light • Power saving "sleep mode" when not in use.
SPECIFICATIONS Transmitter: 3VDC (CR2032 Battery) Reverse polarity protected 433.92MHz transmitting frequency Receiver:
12VDC or 24VDC 10 amp or 5 amp AGC Quick Blow Fuse Input power short circuit protection
Long Life Lithium Battery
INSTALLATION The Jabsco 60000-0000/0024 Remote adds wireless control to new or existing Jabsco searchlight installations. It works in conjunction with a standard hard wired Jabsco panel mount controller, thereby adding a second controller for wireless remote operation of the searchlight at a distance of up to 100' (30 Meters). In applications where a panel mounted controller is not desired, the 60000-0000/0024 Wireless Remote Control System can be set up for wireless-only operation.
r ! r ! r !
!
!
Range:
100 Ft. (30 Meters)
Temperature Range:
(-30° C to 70° C)
Regulatory Compliance: FCC, Australia, Industry Canada and Europe (For Radiated Emissions)
Model 60000-Series
WIRELESS REMOTE CONTROL
WARNING
Disconnect battery before proceeding. Connecting cables to the wireless receiver with power "on" to the receiver can damage the unit.
CAUTION
Do not cut or trim the black receiver antenna wire (so marked) nor connect it to battery ground (-).
CAUTION
Do not immerse the hand-held wireless fob in water.
The Jabsco wireless receiver is installed inline between the searchlight and the hard wired panel controller. (see Fig. 1, 2). For installations where wireless-only operation is preferred, the receiver's (female) connector cable is connected to the searchlight cable. The receiver's (male) connector cable is not connected in this instance. In installations where the wireless remote will be used as a second controller, (in addition to the hard wired panel controller), the receiver's (male) connector cable is connected directly to the the back of the panel controller or to the wire pigtail coming from the back of the panel controller.
Transmitter Cable Connectors
To Wired Controller
To Searchlight
In instances where the pigtail from the panel controller is not terminated with a Molex connector for connection directly to the receiver cable, use the butt connectors supplied to make wire to wire connections between the controller panel and the receiver. See Fig. 1, 2 below for the wire to wire color coding. Note that the blue wire from the receiver will, for example, connect to the blue wire from the panel controller pigtail, the yellow to yellow, etc.
Black to Controller Brown to Controller Green to Light Green to Controller Blue to Controller Yellow to Light Yellow to Controller (+) Power to Battery
Black to Light Brown to Light Orange to Light Orange to Controller Blue to Light Gray to Light Gray to Controller (-) Ground to Battery
JABSCO WIRELESS RECEIVER CONTROLLER & LIGHT CABLE WIRE COLOR CODING
Panel Controller
Black to Controller Brown to Controller Green to Light Green to Controller Blue to Controller Yellow to Light Yellow to Controller (+) Power to Battery
Black to Light Brown to Light Orange to Light Orange to Controller Blue to Light Not Used Not Used (-) Ground to Battery
Wireless Receiver
5” Searchlight
Fig. 2 (Lights with 43670-1003 Controller)
Mount the receiver in a suitable location using the two screws supplied. LEARNING MODE PROCEDURE Note: The transmitter included with this product was initialized at the factory. It is not necessary to conduct this procedure unless adding or replacing a transmitter. Disconnect battery power to the receiver. Press and hold the “on/off” transmitter button while reconnecting power to the receiver. The searchlight will turn “on” within (2) seconds. Code synchronization is complete.
Panel Controller
Wireless Receiver
135 Searchlight
Fig. 1 (Lights with 60020-0000 Controller)
The Jabsco Wireless Remote Control Sytem can support (4) separate transmitters. Each time a transmitter is added to the system or is replaced, all transmitters require re-initialization using the above procedure. Power to the receiver must be disconnected then reconnected while pressing the transmitter’s “on/off” button for each transmitter added in turn.
OPERATING INSTRUCTIONS
FCC GUIDELINES
With the wireless receiver installed and connected to the searchlight cable and to the panel mounted controller (if used), follow the following procedure.
This device complies with part 15 of the FCC Rules. (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation.
Connect battery power to the receiver, searchlight and hard wired panel mounted controller (if installed). Press and hold the “on/off” button on the wireless tranmitter for approximately (1) second. The searchlight will turn “on”. Note: The red LED Signal Transmission Indicator should be blinking while the button is depressed. If not, replace the transmitter battery, accessed by removing the (4) screws on the rear of the case. With the light “on”, switching from spot to flood beam (for 5” chrome/stainless and older 7” chrome models), is accomplished by pressing and releasing the “on/off” button quickly with no hold time. To turn the light “off”, press and hold the “on/off” button for (1) second or until the searchlight turns “off”. The Jabsco 60000-0000/0024 Wireless Remote Control features a true 8-way directional touch pad. The light’s movement can be directed in the horizontal and vertical simultaneously for quicker times-to-target. Searchlight movement is instantaneous with no rotation “run-by” when the pad is released. This provides precise pointing control. The wired panel controller and the wireless transmitter share command of the light equally. Command input from either will be executed by the searchlight. Note: In cases when the 43670-1003 Controller toggle switch is set to “F” for “flood” or “S” for “spot”, the beam can still be switched using the wireless transmitter. The wireless transmitter command will then override the 43670-1003 switch setting. In this instance the toggle switch will indicate a flood beam, for example, when the light is actually in spot mode, having been switched to “spot” using the wireless transmitter. Control is returned to the wired controller with any movement of its joystick. The searchlight beam angle will then change to match that indicated by the toggle switch. When the searchlight has been turned “on” using thehard wired panel controller’s “on/off” toggle switch, thelight can be turned “off” using the wireless transmitter without the need to return to the helm station to deactivate the light. Although the toggle switch then indicates “on”, the searchlight will be “off”. With any movment of the wired controller’s joystick the light will turn “on” and the beam angle (spot vs. flood) will be as indicated by the toggle switch. CIRCUIT PROTECTION An AGC 10 amp (for 12VDC) or 5 amp (for 24VDC) quick blow fuse is included with the wireless receiver cable assembly. In the event that it should be necessary to replace the fuse, the inline fuse holder is located on the receiver’s power lead.
Section 15.105 Information to the user Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequencey energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1. Reorient or relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment into an outlet on a circuit dif ferent from that to which the receiver is connected. 4. Consult the dealer or an experienced radio/TV technician for help. ITT Marine and Leisure declares that this device is in compliance with the essential requirements and adheres to relevant provisions of Directive 1999/5/EC.
1
2
3
4
Qty.
Part Number
1 1 1 1
1000616-01K 1000617-01K 1000618-01K 1000626-01K
PARTS LIST Key
1 2 3 4
Description
Wireless Reciever Receiver Cable Assembly Wireless Transmitter Lanyard
ONE YEAR LIMITED WARRANTY SPECIAL OR CONSEQUENTIAL DAMAGE OF ANY KIND, WHETHER BASED UPON WARRANTY, CONTRACT, NEGLIGENCE, OR STRICT LIABILITY ARISING IN CONNECTION WITH THE SALE, USE, OR REPAIR OF THE PRODUCT.
A. LIMITED WARRANTY: Jabsco warrants that at the time of shipment, the products manufactured by Jabsco and sold hereunder shall be in conformity with applicable written specifications and descriptions referred to or set forth herein, free from defects in material and workmanship, merchantable, and suitable for a particular purpose, provided such is implied by State law under the circumstances of this sale.
3.
THE MAXIMUM LIABILITY OF ITT IN CONNECTION WITH THIS WARRANTY SHALL NOT IN ANY CASE EXCEED THE CONTRACT PRICE FOR THE PRODUCT CLAIMED TO BE DEFECTIVE OR UNSUITABLE.
4.
This warranty does not extend to any product manufactured by Jabsco which has been subjected to misuse, neglect, accident, improper installation, or use in violation of instructions furnished by Jabsco.
5.
This warranty does not extend to or apply to any unit which has been repaired or altered at any place other than Jabsco’s factory, or by persons not expressly approved by Jabsco, nor to any unit the serial number, model number, or identification of which has been removed, defaced or changed.
6.
Components manufactured by any supplier other than Jabsco shall bear only that warranty made by the manufacturer of that product.
7.
This warranty applies to products defined as “consumer products” by the Consumer Product Warranties Act as from time to time amended.
B. WARRANTY ADJUSTMENT: 1.
Jabsco agrees to repair or furnish a replacement for, but not to remove or install, any product or component thereof which, within one (1) year from date of purchase, shall upon test and examination by Jabsco prove defective within the above warranty. Receipt verifying purchase date is required to obtain adjustment.
2.
Buyer shall notify Jabsco of any defect within this warranty no later than ninety (90) days after the defect is discovered.
3.
No product will be accepted for return or replacement without the prior written authorization of Jabsco. Upon such authorization, and in accordance with instructions from Jabsco, the product will be returned to Jabsco, shipping charges prepaid by Buyer. Products returned to Jabsco will be addressed as follows: JABSCO Cape Ann Industrial Park Gloucester, MA 01930
D. CONSUMER RIGHTS:
Or to such alternate locations as may be designated on the product, its container, or this sheet. Repair or replacement made under this warranty will be shipped prepaid to Buyer.
C. EXCLUSIONS FROM WARRANTY AND LIMITATION OF LIABILITY: 1.
The foregoing warranty is limited solely as set forth herein and applies only for the period designated above.
2.
ITT SHALL NOT BE LIABLE FOR ANY LOSS, DAMAGE,
This warranty gives you specific legal rights, and you may have other rights which vary from state to state. Some states do not allow exclusion or limitation of damages. STANDARD WARRANTY: If the products manufactured and sold hereunder are not Consumer Products, the warranty extended to Buyer shall be as set forth in subparagraphs (A), (B), and (C), EXCEPT THAT ALL EXPRESS OR IMPLIED WARRANTIES OR MERCHANTABILITY OR SUITABILITY FOR ANY PARTICULAR PURPOSE ARE EXCLUDED.
www.jabsco.com USA Jabsco 1 Kondelin Road Gloucester, MA 01930 Tel: 978 281 0440 Fax: 978 281 2619
UK Jabsco Bingley Road, Hoddesdon Hertfordshire EN11 OBU Tel: +44 (0) 1992 450145 Fax: +44 (0) 1992 467132
CANADA Fluid Products Canada 55 Royal Road Guelph, Ontario N1H 1T1 Tel: 519 821 1900 Fax: 519 821 2569
JAPAN NHK Jabsco Company Ltd. 3-21-10, Shin-Yokohama Kohoku-Ku, Yokohama, 222 Tel: 045 475 8906 Fax: 045 475 8908
GERMANY Jabsco GmbH Oststrasse 28 22840 Norderstedt Tel: +49-40-53 43 73 -0 Fax: +49-40-53 53 73 -11
ITALY Jabsco Marine Italia S.r.l., Via Tomasseo, 6, 20059 Vimercate, Milano Tel: +39 039 6852323 Fax: +39 039 666307
Warranty: All products of the company are sole and all services of the company are offered subject to the company’s warranty and terms and conditions of sale, copies of which will be furnished upon request. The information provided herein is for guidance only, it does not constitute a guarantee of performance or specification of any individual product or component.
© Copyright 2007, ITT Corporation
Printed in U.S.A.
All Rights Reserved
Form: 950-0235
Rev. C 05/2007