VENTILATED FAÇADES
Technical manual
Ventilated façades The term “ventilated façades” refers to an opaque wall with an outer coating composed of discontinuous elements made of Panariagroup ceramic surfaces of large sizes. These elements are installed “dry” with a mechanical or chemical-mechanical bond. Between these ceramic surfaces and the wall behind, a space is created that allows air circulation. Their technical characteristics, combined with their unique beauty, make Panariagroup ceramic surfaces ideal for ventilated wall systems.
THE STRENGTHS OF PANARIAGROUP VENTILATED FAÇADES
Superior mechanical strength
Resistant to thermal shock
≤ 0,1% Minimum water absorption
High frost resistance
Fireproof
Resistance of colours to sunlight and to ageing
Resistant to stains and smog
Resistant to atmospheric agents
Light and easy to install
Easy to restore original appearance in case of vandalism or graffiti
1
Contents Ventilated faรงades with hidden anchors - LUNA SLOT SYSTEM
In partnership with DALLERA
porcelain stoneware
laminated porcelain stoneware
- Formats: up to 60x120 cm - Thickness: from 9 to 20 mm
- Formats: up to 300x100 cm - Type: laminated porcelain stoneware double-layer
Mechanical bonding With slots on the horizontal edge of the tiles where the fixing hooks connected to the supporting structure are inserted
p. 08
- GEOS SYSTEM
In partnership with GEOS ITALY
- Formats: up to 60x120 cm - Thickness: from 9 to 20 mm
Mechanical bonding With slots at the back of the tile, in which metal profiles are inserted which fix the tile to the bearing structure
In partnership with ADERMA
- Formats: up to 60x120 cm - Thickness: from 9 to 20 mm
- LUNA VISTA SYSTEM
In partnership with DALLERA
porcelain stoneware
laminated porcelain stoneware
- Formats: up to 60x120 cm - Thickness: from 9 to 20 mm
- Formats: up to 300x100 cm - Type: laminated porcelain stoneware 3Plus/5Plus
Mechanical bonding With camouflaged hooks on the horizontal edge of the tiles, used to fix the tiles to the supporting structure
p. 16 - Formats: up to 300x100 cm - Type: laminated porcelain stoneware 5Plus
p. 24
- ADERMA SYSTEM
Ventilated faรงades with visible anchors
p. 30
p. 60
- VENERE SORMONTATO SYSTEM In partnership with DALLERA
Mechanical bonding With camouflaged hooks on the horizontal edge of the overlapping tiles, used to fix the tiles to the supporting structure
- SIRIO SYSTEM
In partnership with DALLERA
/
Mechanical bonding With slots on the vertical edge of the tiles where the fixing hooks connected to the supporting structure are inserted
- Formats: up to 60x120 cm - Thickness: from 9 to 20 mm
p. 68 - Formats: up to 300x50 cm - Type: laminated porcelain stoneware 3Plus/5Plus
p. 76 /
p. 84 - Formats: up to 300x100 cm - Type: laminated porcelain stoneware 3Plus/5Plus
Mechanical bonding With holes drilled through the tiles in which camouflaged bolts are inserted and screwed to the bearing structure
p. 36
- PROGEST SYSTEM
In partnership with PROGEST Structurally adhered bonding By structurally binding metal profiles on the back of the tiles, which are then secured mechanically to the bearing structure
- GENIUS LIGHT SYSTEM
In partnership with FISCHER
- Formats: up to 60x120 cm - Thickness: from 9 to 20 mm
p. 92 - Formats: up to 300x100 cm - Type: laminated porcelain stoneware 5Plus
p. 42 - Formats: up to 60x120 cm - Thickness: from 9 to 20 mm
p. 48
- SIMPLE SYSTEM
In partnership with FISCHER
- Formats: up to 60x120 cm - Thickness: from 9 to 20 mm
/
Mechanical bonding With camouflaged hooks on the horizontal edge of the tiles, used to fix the tiles to the supporting structure
p. 100
/
Mechanical bonding With slots at the back of the tile, in which metal profiles are inserted which fix the tile to the bearing structure
p. 54
2
3
Protoshop of Lamborghini Location: Sant’Agata Bolognese (BO) - Italy
Tower 1 “IQ-quarter” Location: Moscow - Russia
4
Modena racetrack Location: Modena - Italy
Panaria Ceramica Headquarters Location: Finale Emilia - Italy
5
Reale Mutua Headquarters Location: Turin - Italy
Residential building Location: Croatia
6
Vertical Forest Location: Milan - Italy
Private house Location: Aversa (CE) - Italy
7
01
Panariagroup > ventilated façades
LUNA SLOT SYSTEM PANARIAGROUP PORCELAIN STONEWARE
DESCRIPTION OF THE SYSTEM:
SYSTEM COMPONENTS
Hidden anchors
The “LUNA SLOT” system consists of the following elements: • Extruded “L1” profile in aluminium alloy EN 6060 T5 (or similar, according to requirements); • Support hooks of the tiles “T6/30 dx” and “T6/30 sx” stainless steel EN 1.4310 (AISI 301); • Standard support brackets “A12” and “B12” made from extruded aluminium EN 6060; • Stainless steel screws, for fixing “L1” profile to the brackets; • Anchoring dowels for fixing brackets to the wall, mechanically or with chemical resin as necessary; • Silicone drops bonding the tiles to hooks and profile.
TYPE OF CLADDING TILES: Panariagroup porcelain stoneware tiles with thickness from 9 to 20 mm OPERATIONS CARRIED OUT ON THE TILE: Slots on the horizontal edge CLADDING TILE SIZES: All sizes of Panariagroup product range In partnership with DALLERA
SYSTEM DESCRIPTION The system consists of a mounted aluminium vertical profile “L1” with a pitch equal to the width of the tile, plus the joint of the project. The vertical profile “L1” is shaped to accommodate without drilling the following accessories: • wall fixing brackets screwed with stainless steel bolts, according to project pitch; • the hooks “T6/30sx” and “T6/30dx” to support the cladding tiles. The cladding tiles are held in place by means of hooks which are inserted into the slots previously machined on the edge of the tiles and which fit into the grooves of the profiles “L1”. Each tile can be assembled or disassembled independently by snapping the hooks “T6/30” into the slots on the front of the profile “L1”. The number of hooks depends on the size of the tile and the load on the wall. Structural adhesive is also applied between the lateral edges of the profile and the back of the tile to improve the mechanical support of the system. As there are no holes, no damage is done to the surface protection (caused by oxidation or electrocoloring) and this increases the lifecycle of the profiles. The supporting structure allows any type of adjustment; it is able to protect from wind loads and allows the thermal expansion of the different components. SYSTEM SIZES: • The standard distance between the wall and the internal face of the tiles is 130 mm, with a standard adjustment range of ± 25 mm. • The standard thickness of Panariagroup porcelain stoneware tiles for this type of system is from 9 to 20 mm.
8
9
01
Panariagroup > ventilated faรงades
LUNA SLOT SYSTEM PANARIAGROUP PORCELAIN STONEWARE Standard solution for mid-section
Components
PROFILE L3
Vertical section - Scale 1:4
STRUCTURAL ADHESIVE
HOOK T6/V3 HORIZONTAL JOINTS
SINGLE BRACKET
HOOK T6/V3
DOUBLE BRACKET PROFILE L3m PROFILE L3
STRUCTURAL ADHESIVE
HOOKS T6/V3 (dx and sx)
N.B: The actual components may be modified in the design phase.
Standard solution for roof finishing
Standard solution for floor end
Vertical section - Scale 1:4
Vertical section - Scale 1:4
PROFILE L3
CLOSING ELEMENT
HOOK T6/V3
PROFILE L3
STRUCTURAL ADHESIVE
STRUCTURAL ADHESIVE
HOOK T6/V3
ANTI-INSECT CLOSING ELEMENT
10
DISTANCE ACCORDING TO PROJECT SPECIFICATIONS
11
01
Panariagroup > ventilated façades
LUNA SLOT SYSTEM PANARIAGROUP PORCELAIN STONEWARE Cotto d’Este Standard solution porcelain for window tile head
Cotto d’Este Standard closing porcelain solution tile
Horizontal section - Scale 1:4
Horizontal section - Scale 1:4
BRACKET A13
INSULATION
PROFILE L3
DOWEL TO BE DECIDED ACCORDING TO PROJECT SPECIFICATIONS
STRUCTURAL ADHESIVE HOOK T6/V3
INSULATION
HOOK T6/V3
WINDOW
PROFILE L3m
Cotto d’Este Standard solution porcelain for mid-section tile
Vertical section - Scale 1:4
Vertical section - Scale 1:4
WINDOW
Cotto d’Este Standard solution porcelain below tilewindowsill
HORIZONTAL JOINT
PROFILE L3
WINDOWSILL
INSULATION
PROFILE L3m
HOOK T6/V3 HOOK T6/V3 sx
HOOK T6/V3 dx
STRUCTURAL ADHESIVE DOWEL TO BE DECIDED ACCORDING TO PROJECT SPECIFICATIONS
12
STANDARD VERTICAL JOINT
13
01
Panariagroup > ventilated façades
Cotto Tile mounting d’Este porcelain operation tile
Horizontal section - Scale 1:4
Vertical section - Scale 1:4
INSULATION
PROFILE L3m
Cotto d’Este Standard solution porcelain for internal tile angle
PROFILE L3
LUNA SLOT SYSTEM PANARIAGROUP PORCELAIN STONEWARE
HOOK T6/V3
HOOK T6/V3
PROFILE L3m
INSULATION PANNELLO ISOLANTE
STRUCTURAL ADHESIVE
14
15
02
Panariagroup > ventilated façades
LUNA SLOT SYSTEM PANARIAGROUP LAMINATED PORCELAIN STONEWARE
DESCRIPTION OF THE SYSTEM:
SYSTEM COMPONENTS
Hidden anchors
The “LUNA SLOT” system consists of the following elements: • Extruded “L3” profile in aluminium alloy EN 6060 T5 (or similar, according to requirements); • Support hooks of the slabs “T6/V3 dx” and “T6/V3 sx” stainless steel EN 1.4310 (AISI 301); • Standard support brackets “A13” and “B13” made from extruded aluminium EN 6060; • Stainless steel screws, for fixing “L3” profile to the brackets; • Anchoring dowels for fixing brackets to the wall, mechanically or with chemical resin as necessary; • Silicone drops bonding the slabs to hooks and profile.
TYPE OF CLADDING SLABS: Double-layer Panariagroup laminated porcelain stoneware slabs with a thickness of approximately 8 mm (5mm + 3mm) OPERATIONS CARRIED OUT ON THE SLAB: Slots on the horizontal edge CLADDING SLAB SIZES: Maximum size 300x100 cm In partnership with DALLERA
SYSTEM DESCRIPTION The system consists of a mounted aluminium vertical profile “L3” with a pitch equal to the width of the slab, plus the joint of the project. The vertical profile “L31” is shaped to accommodate without drilling the following accessories: • wall fixing brackets screwed with stainless steel bolts, according to project pitch; • the hooks “T6/V3sx” and “T6/V3dx” to support the cladding slabs. The cladding slabs are held in place by means of hooks which are inserted into the slots previously machined on the edge of the slabs and which fit into the groves of the profiles “L3”. Each slab can be assembled or disassembled independently by snapping the hooks “T6/V3” into the slots on the front of the profile “L3”. The number of hooks depends on the size of the slab and the load on the wall. Structural adhesive is also applied between the lateral edges of the profile and the back of the slab to improve the mechanical support of the system. Once the slabs are correctly assembled, each slab can be set-up or dismantled separately on the aluminium structure by putting hooks in the appropriate channel on the rail. This arrangement of the components protects the solution from corrosion and assures a longer lifetime to the structure. The supporting structure allows any type of adjustment; it is able to protect from wind loads and allows the thermal expansion of the different components. SYSTEM SIZES: • The standard distance between the wall and the internal face of the slabs is 111 mm, with a standard adjustment range of ± 25 mm. • The standard thickness of double-layer Panariagroup laminated porcelain stoneware slabs for this type of system is 8 mm.
16
17
02
Panariagroup > ventilated faรงades
LUNA SLOT SYSTEM PANARIAGROUP LAMINATED PORCELAIN STONEWARE Components
Standard solution for mid-section
PROFILE L3
Vertical section - Scale 1:4
SINGLE BRACKET
STRUCTURAL ADHESIVE
HORIZONTAL JOINTS
HOOK T6/V3
HOOK T6/V3
DOUBLE BRACKET PROFILE L3m
STRUCTURAL ADHESIVE
PROFILE L3
HOOKS T6/V3 (dx and sx)
Standard solution for roof finishing
Standard solution for floor end
Vertical section - Scale 1:4
Vertical section - Scale 1:4
PROFILE L3
CLOSING ELEMENT
HOOK T6/V3
PROFILE L3
STRUCTURAL ADHESIVE
STRUCTURAL ADHESIVE
HOOK T6/V3
ANTI-INSECT CLOSING ELEMENT
18
DISTANCE ACCORDING TO PROJECT SPECIFICATIONS
19
02
Panariagroup > ventilated faรงades
LUNA SLOT SYSTEM PANARIAGROUP LAMINATED PORCELAIN STONEWARE Standard solution below windowsill
Horizontal section - Scale 1:4
Vertical section - Scale 1:4
PROFILE L3m
WINDOW
Standard solution for internal angle
WINDOWSILL
PROFILE L3
HORIZONTAL JOINT
HOOK T6/V3
PROFILE L3m
HOOK T6/V3 STRUCTURAL ADHESIVE
INSULATION PANNELLO ISOLANTE DOWEL TO BE DECIDED ACCORDING TO PROJECT SPECIFICATIONS
Standard solution for window head
Standard closing solution
Vertical section - Scale 1:4
Horizontal section - Scale 1:4
INSULATION
DOWEL TO BE DECIDED ACCORDING TO PROJECT SPECIFICATIONS
PROFILE L3
BRACKET A13
STRUCTURAL ADHESIVE
HOOK T6/V3 INSULATION
HOOK T6/V3 sx
WINDOW
PROFILE L3m
20
21
02
Panariagroup > ventilated faรงades
LUNA SLOT SYSTEM PANARIAGROUP LAMINATED PORCELAIN STONEWARE Slab mounting operation
PROFILE L3
INSULATION
Vertical section - Scale 1:4
HOOK T6/V3
STRUCTURAL ADHESIVE ADESIVO STRUTTURALE
22
23
03
Panariagroup > ventilated façades
GEOS SYSTEM PANARIAGROUP PORCELAIN STONEWARE
DESCRIPTION OF THE SYSTEM:
SYSTEM COMPONENTS
Hidden anchors
The “GEOS” system consists of the following elements: • Aluminium profiles EN AW - 6060 manufactured by Geos Italy and pre-assembled on the cladding tiles; • Bolts in galvanized steel; • Mounting bracket for wall fixing GEOS ITALY.
TYPE OF CLADDING TILES: Panariagroup porcelain stoneware tiles with thickness from 9 to 20 mm OPERATIONS CARRIED OUT ON THE TILE: Slots on the back of the tiles CLADDING TILE SIZES: All sizes of Panariagroup product range In partnership with GEOS ITALY
SYSTEM DESCRIPTION The new wall cladding concept by GEOS ITALY consists of an aluminium EN AW- 6060 substructure, formed by aluminium profiles that are processed and pre-assembled on the tile according to the orthogonal lines of project. This substructure is equipped with special interconnecting elements which are protected by an international patent duly granted to GEOS ITALY, which oversees their commercial use. These elements greatly facilitate the installation of the tiles and allow for adjustments when the on-site dimensions are different from those on the architectural plan. The substructure profiles possess special guides that fit the anchoring system (bracket and hook) precisely onto the wall (brick, concrete or structural load bearing element). The bracket and hook allow each element to be precisely secured and fixed (230 kg normal traction resistance at the surface of the cladding. This resistance corresponds to the stress along the elements due to wind loads). Perfect alignment and planarity between each tile can be obtained through micrometric adjustments on the four main axes, regardless of any unevenness of the support (whether wall or structure). The installation of the GEOS ITALY ventilated wall does not require any preparation of the support on which it will be fixed. Since each pre-assembled substructure and tile overlaps and connects the element before it, the GEOS ITALY ventilated wall is closedjointed and can therefore be supported by a reduced air circulation chamber. SYSTEM SIZES: • The standard thickness of Panariagroup porcelain stoneware tiles for this type of system is from 9 to 20 mm.
24
25
03
Panariagroup > ventilated faรงades
GEOS SYSTEM PANARIAGROUP PORCELAIN STONEWARE Standard solution for floor end
Standard solution for mid-section
Vertical section - Scale 1:4
Vertical section - Scale 1:4
GROUND
Standard solution for floor end
Standard solution for external angle
Vertical section - Scale 1:4
Horizontal section - Scale 1:4
GROUND
26
27
03
Panariagroup > ventilated faรงades
GEOS SYSTEM PANARIAGROUP PORCELAIN STONEWARE Standard solution for window head Vertical section - Scale 1:4
Standard solution for windowsills Vertical section - Scale 1:4
28
29
04
Panariagroup > ventilated façades
GEOS SYSTEM PANARIAGROUP LAMINATED PORCELAIN STONEWARE
DESCRIPTION OF THE SYSTEM:
SYSTEM COMPONENTS
Hidden anchors
The “GEOS” system consists of the following elements: • Aluminium profiles EN AW - 6060 manufactured by Geos Italy and pre-assembled on the cladding slabs; • Bolts in galvanized steel; • Mounting bracket for wall fixing GEOS ITALY.
TYPE OF CLADDING SLABS: Panariagroup laminated porcelain stoneware 5Plus slabs OPERATIONS CARRIED OUT ON THE SLAB: Slots on the back of the slabs CLADDING SLAB SIZES: Maximum size 300x100 cm In partnership with GEOS ITALY
SYSTEM DESCRIPTION The new wall cladding concept by GEOS ITALY consists of an aluminium EN AW- 6060 substructure, formed by aluminium profiles that are processed and pre-assembled on the slab according to orthogonal lines of the project. This substructure is equipped with special interconnecting elements which are protected by an international patent duly granted to GEOS ITALY, which oversees their commercial use. These elements greatly facilitate the installation of the slabs and allow for adjustments when the on-site dimensions are different from those on the architectural plan. The substructure profiles possess special guides that fit the anchoring system (bracket and hook) precisely onto the wall (brick, concrete or structural load bearing element). The bracket and hook allow each element to be precisely secured and fixed (230 kg normal traction resistance at the surface of the cladding. This resistance corresponds to the stress along the elements due to wind loads). Perfect alignment and planarity between each slab can be obtained through micrometric adjustments on the four main axes, regardless of any unevenness of the support (whether wall or structure). The installation of the GEOS ITALY ventilated wall does not require any preparation of the support on which it will be fixed. Since each pre-assembled substructure and slab overlaps and connects the element before it, the GEOS ITALY ventilated wall is closedjointed and can therefore be supported by a reduced air circulation chamber. SYSTEM SIZES: • The standard thickness of Panariagroup laminated porcelain stoneware slabs for this type of system is 5.5 mm.
30
31
04
Panariagroup > ventilated faรงades
GEOS SYSTEM PANARIAGROUP LAMINATED PORCELAIN STONEWARE Standard solution for floor end
Standard solution for mid-section
Vertical section - Scale 1:4
Vertical section - Scale 1:4
GROUND
Standard solution for floor end
Standard solution for external angle
Vertical section - Scale 1:4
Horizontal section - Scale 1:4
GROUND
32
33
04
Panariagroup > ventilated faรงades
GEOS SYSTEM PANARIAGROUP LAMINATED PORCELAIN STONEWARE Standard solution for window head Vertical section - Scale 1:4
Standard solution for windowsills Vertical section - Scale 1:4
34
35
05
Panariagroup > ventilated façades
ADERMA OVERLAPPING SYSTEM PANARIAGROUP PORCELAIN STONEWARE
DESCRIPTION OF THE SYSTEM:
SYSTEM DESCRIPTION
Hidden anchors
The “ADERMA OVERLAPPING” system consists of vertical profiles “type K” in stainless steel or galvanized steel positioned at a predetermined distance and fixed to the reinforced concrete beams edge through special spacer brackets “omega” (stainless steel or galvanized steel). Their function is to support the weight of the cladding tiles. These are fixed to the wall through mechanical wind load resistant anchoring dowels. The horizontal profile Type “S series” in aluminium 6060 is fixed by screws and spacers that facilitate adjustment and connection to the vertical profiles. These horizontal profiles support the tile and protect against wind load with special hooks “omega fix” in stainless steel AISI 304 that are inserted in the slots on the edge of the tiles.
TYPE OF CLADDING TILES: Panariagroup porcelain stoneware tiles with thickness from 9 to 20 mm OPERATIONS CARRIED OUT ON THE TILE: Slots on the horizontal edge CLADDING TILE SIZES: All sizes of Panariagroup product range
The anchoring system allows any kind of adjustment. It is designed to protect from wind loads and to allow the thermal expansion of the different components. The anchoring system allows any adjustment of the alignment of ± 20 mm, (bigger adjustments are obtained by special spacers) and allows, with some elementary precautions, the dismantling of each tile for maintenance and wall inspection. The anchoring system is CE certified to UNI 1090 standards.
In partnership with ADERMA
36
37
05
Panariagroup > ventilated façades
ADERMA OVERLAPPING SYSTEM PANARIAGROUP PORCELAIN STONEWARE Standard solution for roof finishing
Standard solution for floor end
Vertical section - Scale 1:4
Vertical section - Scale 1:4 CLADDING CERAMIC TILES CLOSING ELEMENT IN MICROPERFORATED METAL SHEET
INSULATION
OMEGA WEIGHT BEARING SPACER BRACKETS
CLADDING CERAMIC TILES
VERTICAL K2 PROFILE AGS1 ANGLE BRACKET “OMEGA FIX” HOOK
TILE HOLDING ANGLE BRACKET S
Standard solution for mid-section
CLOSING ELEMENT IN MICRO-PERFORATED METAL SHEET
Vertical section - Scale 1:4 INSULATION
OMEGA WEIGHT BEARING SPACER BRACKETS
VERTICAL K2 PROFILE
AGS1 ANGLE BRACKET
“OMEGA FIX” HOOK
TILE HOLDING ANGLE BRACKET S
38
39
05
Panariagroup > ventilated façades
ADERMA OVERLAPPING SYSTEM PANARIAGROUP PORCELAIN STONEWARE Standard solution for mid-section
Standard solution for external angle
Horizontal section - Scale 1:4
Horizontal section - Scale 1:4
INSULATION
40
CLADDING CERAMIC TILES
OMEGA WEIGHT BEARING SPACER BRACKETS
“OMEGA FIX” HOOK
VERTICAL K2 PROFILE
TILE HOLDING ANGLE BRACKET S
41
06
Panariagroup > ventilated façades
PROGEST SYSTEM PANARIAGROUP PORCELAIN STONEWARE
DESCRIPTION OF THE SYSTEM:
SYSTEM COMPONENTS
Hidden anchors
The “PROGEST” system consists of vertical elements in extruded aluminium profile (6060 alloy UNI 9006/1) installed on site with a predetermined spacing, according to architectural requirements and the static calculations. All weight bearing components of the structure are in accordance with the UNI 11018.
TYPE OF CLADDING TILES: Panariagroup porcelain stoneware tiles with thickness from 9 to 20 mm OPERATIONS CARRIED OUT ON THE TILE: Metal profiles are inserted on the back of the tile by the means of structural adhesion CLADDING TILE SIZES: All sizes of Panariagroup product range In partnership with PROGEST
SYSTEM DESCRIPTION The “PROGEST” system is designed to create a building envelope with a substructure consisting of extruded aluminium sections and external ceramic cladding. The versions available can satisfy multiple requirements, both from a static and an architectural point of view. It is also very interesting to note that it is possible to use this system on existing buildings to improve their energy efficiency. The vertical elements are anchored to the substructure with adjustable brackets that allow for thermal expansion and contraction. To fix the brackets to the existing walls, following pull-out tests, high resistance mechanical and chemical fixing are used. The anchoring of the cladding tiles to the load-bearing structure is done with “L” shaped profiles placed on the back of the tiles themselves, with certified structural bonding. The “L” shaped profiles have special slots that are hooked to the adjustable supporting element placed on the vertical profiles. The tiles, once installed, will be supported by two elements that will be placed on the vertical profiles so that the sealants are not subject to tear, thus maintaining their elastic and mechanical characteristics. SYSTEM SIZES: • The standard thickness of Panariagroup porcelain stoneware tiles for this type of system is from 9 to 20 mm.
42
43
06
Panariagroup > ventilated faรงades
PROGEST SYSTEM PANARIAGROUP PORCELAIN STONEWARE Standard components
Standard solution for mid-section Vertical section - Scale 1:4
N.B: The actual components may be modified in the design phase.
44
Standard solution for roof finishing
Standard solution for floor end
Vertical section - Scale 1:4
Vertical section - Scale 1:4
45
06
Panariagroup > ventilated faรงades
PROGEST SYSTEM PANARIAGROUP PORCELAIN STONEWARE Standard solution for mid-section
Vertical section - Scale 1:4
Horizontal section - Scale 1:4
L. MODULE
L. MODULE 30/10 ALUMINIUM METAL SHEET
Standard solution for windowsills
STRUCTURAL SILICONE L. MODULE SEE DATA SHEET
VARIABLE
VARIABLE
VARIABLE
VARIABLE
Standard solution for window frame
L. MODULE SEE DATA SHEET
H. MODULE
Vertical section - Scale 1:4
46
47
07
Panariagroup > ventilated façades
PROGEST SYSTEM PANARIAGROUP LAMINATED PORCELAIN STONEWARE
DESCRIPTION OF THE SYSTEM:
SYSTEM COMPONENTS
Hidden anchors
The “PROGEST” system consists of vertical elements in extruded aluminium profile (6060 alloy UNI 9006/1) installed on site with a predetermined spacing, according to architectural requirements and the static calculations. All weight bearing components of the structure are in accordance with the UNI 11018.
TYPE OF CLADDING SLABS: Panariagroup laminated porcelain stoneware 5Plus slabs OPERATIONS CARRIED OUT ON THE SLAB: Metal profiles are inserted on the back of the slab by the means of structural bonding CLADDING SLAB SIZES: Maximum size 300x100 cm In partnership with PROGEST
SYSTEM DESCRIPTION The “PROGEST” system is designed to create a building envelope with a substructure consisting of extruded aluminium sections and external ceramic cladding. The versions available can satisfy multiple requirements, both from a static and an architectural point of view. It is also very interesting to note that it is possible to use this system on existing buildings to improve their energy efficiency. The vertical elements are anchored to the substructure with adjustable brackets that allow for thermal expansion and contraction. To fix the brackets to the existing walls, following pull-out tests, high resistance mechanical and chemical fixing are used. The anchoring of the cladding slabs to the load-bearing structure is done with “L” shaped profiles placed on the back of the slabs themselves, with certified structural bonding. The “L” shaped profiles have special slots that are hooked to the adjustable supporting element placed on the vertical profiles. The slabs, once installed, will be supported by two elements that will be placed on the vertical profiles so that the sealants are not subject to tear, thus maintaining their elastic and mechanical characteristics. SYSTEM SIZES: • The standard thickness of Panariagroup laminated porcelain stoneware slabs for this type of system is 5.5 mm.
48
49
07
Panariagroup > ventilated faรงades
PROGEST SYSTEM PANARIAGROUP LAMINATED PORCELAIN STONEWARE Standard components
Standard solution for mid-section Vertical section - Scale 1:4
N.B: The actual components may be modified in the design phase.
50
Standard solution for roof finishing
Standard solution for floor end
Vertical section - Scale 1:4
Vertical section - Scale 1:4
51
07
Panariagroup > ventilated faรงades
PROGEST SYSTEM PANARIAGROUP LAMINATED PORCELAIN STONEWARE Standard solution for mid-section
Vertical section - Scale 1:4
Horizontal section - Scale 1:4
VARIABLE
VARIABLE
VARIABLE
VARIABLE
Standard solution for window frame
L. MODULE
L. MODULE
30/10 ALUMINIUM METAL SHEET
Standard solution for windowsills
STRUCTURAL SILICONE L. MODULE SEE DATA SHEET
L. MODULE SEE DATA SHEET
H. MODULE
Vertical section - Scale 1:4
52
53
08
Panariagroup > ventilated façades
GENIUS LIGHT SYSTEM PANARIAGROUP PORCELAIN STONEWARE
DESCRIPTION OF THE SYSTEM:
SYSTEM COMPONENTS
Hidden anchors
The “GENIUS LIGHT” system consists of the following elements: • Extruded vertical profile “ VP LT / VP L” made in aluminum alloy EN 6063 T66; • Extruded horizontal profile “ HP LC” made in aluminum alloy EN 6063 T66; • Fixing-point holder “LFH” made in aluminum alloy EN 6063 T66; • Sliding-point holder “LSH” made in aluminum alloy EN 6063 T66; • Adjustable fixed hanger support “BR-AFH” made in aluminum alloy EN 6063 T66; • Adjustable sliding hanger support “BR-ASH” made in aluminum alloy EN 6063 T66; • Sliding support “BR-SH” made in aluminum alloy EN 6063 T66; • Rivets made in stainless steel AISI 304 for connection of wall holder “LFH / LSH” to profile “VP LT / VP L”; • Preassembled screw made in stainless steel AISI 304 for hanger “ BR-AFH / BR-ASH”; • Insulating barrier pad “THERMO-PAD” made in PA; • Tile anchor “FZP II-T” made in stainless steel AISI 316 with CE marking; • Mechanical or chemical anchors with CE marking made in stainless steel AISI 316 to fix “LFH / LSH “ on support.
TYPE OF CLADDING TILES: Panariagroup porcelain stoneware tiles with thickness from 9 to 20 mm OPERATIONS CARRIED OUT ON THE TILE: Undercut hole on the back of the tiles CLADDING TILE SIZES: All sizes of Panariagroup product range In partnership with FISCHER
SYSTEM DESCRIPTION The system provide the use of vertical profile VP, spaced according to the design, and fastened to the support by means of wall holders LFH/LSH through stainless steel A2 rivets. The wall holders are designed according to UNI 11018 and allow the thermal expansion of vertical profile. The fixing to the support is assured by fischer mechanical or chemical anchors. The vertical profile is equipped with a guide for maximum excursion when inserted in the LFH and LSH wall holders. The substructure is completed with a horizontal profile “HP-LC”, suitable to accommodate hangers BR-AFH / BR-ASH / BR-SH. The horizontal profile, with spacing equal to the height of the tiles, is fastened to the vertical profile by means of stainless steel A2 rivets through the slotted hole of the horizontal profile. The slotted holes permit the thermal expansion of the profile. The tiles are anchored to the horizontal profile by means pre-assemble hanger on the back of the panel. The hangers fastened with the undercut anchor fischer FZP II T. The system is suitable to realize a facade with regular pattern of tiles or vertical staggered joint. The anchor FZP II T is installed into pre-drilled undercut hole made with a special fischer diamond drill bit FZP B. The special undercut geometric expansion does not create stress inside the tile. This technology offers several times higher ultimate loads than conventional fixings. This allows reduced panel thickness and larger panel sizes. SYSTEM SIZES: • With the different wall holders (LFH /LSH) the standard distance between the wall and the internal face of the tiles can vary between 100 mm and 255 mm. • The standard thickness of Panariagroup porcelain stoneware tiles for this type of system is from 9 to 20 mm.
54
55
08
Panariagroup > ventilated faรงades
GENIUS LIGHT SYSTEM PANARIAGROUP PORCELAIN STONEWARE Standard components
Standard solution for mid-section Vertical section - Scale 1:5
N.B: The actual components may be modified in the design phase.
56
Standard solution for roof finishing
Standard solution for floor end
Vertical section - Scale 1:5
Vertical section - Scale 1:5
57
08
Panariagroup > ventilated façades
GENIUS LIGHT SYSTEM PANARIAGROUP PORCELAIN STONEWARE
58
Cotto d’Este Standard solution porcelain for window tile head
Cotto d’Este Standard solution porcelain for internal tile angle
Vertical section - Scale 1:5
Vertical section - Scale 1:5
Cotto d’Este Standard solution porcelain below tilewindowsill
Cotto d’Este Standard solution porcelain for external tile angle
Vertical section - Scale 1:5
Vertical section - Scale 1:5
59
09
Panariagroup > ventilated façades
LUNA VISTA SYSTEM PANARIAGROUP PORCELAIN STONEWARE
SYSTEM TYPE:
SYSTEM COMPONENTS
Visible hooks
The “LUNA VISTA” system consists of the following elements: • Extruded “L8” profile in aluminium alloy EN 6060 T5 (or similar, according to requirements); • Extruded “L1” profile in aluminium alloy EN 6060 T5 (or similar, according to requirements); • Support hooks of the tiles “T6/V3 dx” and “T6/V3 sx” stainless steel EN 1.4310 (AISI 304); • Standard support brackets “A13” and “B13” made from extruded aluminium EN 6060; • Stainless steel screws, for fixing “L8” profiles to the brackets; • Anchoring dowels for fixing brackets to the wall, mechanically or with chemical resin as necessary; • Silicone drops bonding the tiles to hooks and profile.
TYPE OF CLADDING TILES: Panariagroup porcelain stoneware tiles with thickness from 9 to 20 mm OPERATIONS CARRIED OUT ON THE TILE: None CLADDING TILE SIZES: All sizes of Panariagroup product range In partnership with DALLERA
SYSTEM DESCRIPTION The system consists of a vertical aluminium profile “L8” with a spacing depending on the width of the tiles, plus the joint and the vertical aluminium “L1” profile where required by the project in case of big size tiles. The vertical profiles “L8” and “L1” are shaped to accommodate without drilling the following accessories: • wall fixing brackets screwed with stainless steel bolts, according to project pitch; • the glazed hooks “T6/V3sx” and “T6/V3dx” to support the cladding tiles. The cladding tiles are held in position by means of hooks that fit into the grooves of the profiles “L8” or “L1”. If needed, the hooks can be painted the same colour of the tiles surface so that they are not visible not even from a small distance from the cladding itself. Each tile can be assembled or disassembled independently, by snapping the hooks “T6/V3” into the slots on the front of the vertical profile. The number of hooks depends on the size of the tiles and the loads on the wall. Structural adhesive is also applied between the lateral edges of the profile and the back of the tile to improve the mechanical support of the system. As there are no holes, no damage is done to the surface protection (caused by oxidation or electrocoloring) and this increases the life-cycle of the profiles. The supporting structure allows any type of adjustment; it is able to protect from wind loads and allows the thermal expansion of the different components. SYSTEM SIZES: • The standard distance between the wall and the internal face of the tiles is 111 mm, with a standard adjustment range of ± 25 mm. • The standard thickness of Panariagroup porcelain stoneware tiles for this type of system is from 9 to 20 mm.
60
61
09
Panariagroup > ventilated faรงades
LUNA VISTA SYSTEM PANARIAGROUP PORCELAIN STONEWARE Components
Standard solution for mid-section
PROFILE L8
Vertical section - Scale 1:4
STRUCTURAL ADHESIVE
HOOK T6/V3
HORIZONTAL JOINTS
SINGLE BRACKET
HOOK T6/V3
HOOKS T6/V3 (dx and sx)
STRUCTURAL ADHESIVE
DOUBLE BRACKET
L1 PROFILE
N.B: The actual components may be modified in the design phase.
Standard solution for roof finishing
Standard solution for floor end
Vertical section - Scale 1:4
Vertical section - Scale 1:4
PROFILE L8
CLOSING ELEMENT
HOOK T6/V3
PROFILE L8
STRUCTURAL ADHESIVE
STRUCTURAL ADHESIVE
HOOK T6/V3
ANTI-INSECT CLOSING ELEMENT
62
DISTANCE ACCORDING TO PROJECT SPECIFICATIONS
63
09
Panariagroup > ventilated faรงades
LUNA VISTA SYSTEM PANARIAGROUP PORCELAIN STONEWARE
Horizontal section - Scale 1:4
Vertical section - Scale 1:4
HOOK T6/V3
WINDOW
Standard solution below windowsill
PROFILE L1
Standard solution for internal angle
WINDOWSILL
PROFILE L1
HORIZONTAL JOINT
PROFILE L8
HOOK T6/V3
HOOK T6/V3
STRUCTURAL ADHESIVE
INSULATION DOWEL TO BE DECIDED ACCORDING TO PROJECT SPECIFICATIONS
Standard solution for window head
Standard solution for mid-section
Vertical section - Scale 1:4
Horizontal section - Scale 1:4
INSULATION
DOWEL TO BE DECIDED ACCORDING TO PROJECT SPECIFICATIONS
PROFILE L8
BRACKET A13
STRUCTURAL ADHESIVE
HOOK T6/V3
INSULATION
PROFILE L1
WINDOW
HOOK T6/V3 sx
64
HOOK T6/V3 dx
STANDARD HORIZONTAL JOINT
65
09
Panariagroup > ventilated faรงades
Tile mounting operation
Horizontal section - Scale 1:4
Vertical section - Scale 1:4
INSULATION
Standard horizontal closing solution
PROFILE L8
LUNA VISTA SYSTEM PANARIAGROUP PORCELAIN STONEWARE
HOOK T6/V3
INSULATION
PROFILE L1
HOOK T6/V3 sx
12.8
66
STRUCTURAL ADHESIVE ADESIVO STRUTTURALE
67
10
Panariagroup > ventilated façades
LUNA VISTA SYSTEM PANARIAGROUP LAMINATED PORCELAIN STONEWARE
SYSTEM TYPE:
SYSTEM COMPONENTS
Visible hooks
The “LUNA VISTA” system consists of the following elements: • Extruded “L8” profile in aluminium alloy EN 6060 T5 (or similar, according to requirements); • Extruded “L1” profile in aluminium alloy EN 6060 T5 (or similar, according to requirements); • Support hooks of the slabs “T6/V3 dx” and “T6/V3 sx” stainless steel EN 1.4310 (AISI 304); • Standard support brackets “A13” and “B13” made from extruded aluminium EN 6060; • Stainless steel screws, for fixing “L8” profiles to the brackets; • Anchoring dowels for fixing brackets to the wall, mechanically or with chemical resin as necessary; • Silicone drops bonding the slabs to hooks and profile.
TYPE OF CLADDING SLABS: Panariagroup laminated porcelain stoneware 3Plus or 5Plus slabs OPERATIONS CARRIED OUT ON THE SLAB: None CLADDING SLAB SIZES: Maximum size 300x100 cm In partnership with DALLERA
SYSTEM DESCRIPTION The system consists of a vertical aluminium profile “L8” with a spacing depending on the width of the slabs, plus the joint and the vertical aluminium “L1” profile where required by the project in case of big size slabs. The vertical profiles “L8” and “L1” are shaped to accommodate without drilling the following accessories: • wall fixing brackets screwed with stainless steel bolts, according to project pitch; • the glazed hooks “T6/V3sx” and “T6/V3dx” to support the cladding slabs. The cladding slabs are held in position by means of hooks that fit into the grooves of the profiles “L8” or “L1”. If needed, the hooks can be painted the same colour of the slabs surface so that they are not visible not even from a small distance from the cladding itself. Each slab can be assembled or disassembled independently, by snapping the hooks “T6/V3” into the slots on the front of the vertical profile. The number of hooks depends on the size of the slab and the load on the wall. Structural adhesive is also applied between the lateral edges of the profile and the back of the slab to improve the mechanical support of the system. As there are no holes, no damage is done to the surface protection (caused by oxidation or electrocoloring) and this increases the life-cycle of the profiles. The supporting structure allows any type of adjustment; it is able to protect from wind loads and allows the thermal expansion of the different components. SYSTEM SIZES: • The standard distance between the wall and the internal face of the slabs is 111 mm, with a standard adjustment range of ± 25 mm. • The standard thickness of Panariagroup laminated porcelain stoneware slabs for this type of system is 3.5 or 5.5 mm.
68
69
10
Panariagroup > ventilated faรงades
LUNA VISTA SYSTEM PANARIAGROUP LAMINATED PORCELAIN STONEWARE Components
Standard solution for mid-section
PROFILE L8
Vertical section - Scale 1:4
STRUCTURAL ADHESIVE
HOOK T6/V3
HORIZONTAL JOINTS
SINGLE BRACKET
HOOK T6/V3
HOOKS T6/V3 (dx and sx)
STRUCTURAL ADHESIVE
DOUBLE BRACKET
L1 PROFILE
N.B: The actual components may be modified in the design phase.
Standard solution for roof finishing
Standard solution for floor end
Vertical section - Scale 1:4
Vertical section - Scale 1:4
PROFILE L8
CLOSING ELEMENT
HOOK T6/V3
PROFILE L8
STRUCTURAL ADHESIVE
STRUCTURAL ADHESIVE
HOOK T6/V3
ANTI-INSECT CLOSING ELEMENT
70
DISTANCE ACCORDING TO PROJECT SPECIFICATIONS
71
10
Panariagroup > ventilated faรงades
LUNA VISTA SYSTEM PANARIAGROUP LAMINATED PORCELAIN STONEWARE
Horizontal section - Scale 1:4
Vertical section - Scale 1:4
HOOK T6/V3
WINDOW
Standard solution below windowsill
WINDOWSILL
HOOK T6/V3
PROFILE L8
PROFILE L1
HORIZONTAL JOINT
PROFILE L1
Standard solution for internal angle
HOOK T6/V3
STRUCTURAL ADHESIVE INSULATION PANNELLO ISOLANTE DOWEL TO BE DECIDED ACCORDING TO PROJECT SPECIFICATIONS
Standard solution for window head
Standard solution for mid-section
Vertical section - Scale 1:4
Horizontal section - Scale 1:4
INSULATION
DOWEL TO BE DECIDED ACCORDING TO PROJECT SPECIFICATIONS
PROFILE L8
BRACKET A13
STRUCTURAL ADHESIVE
HOOK T6/V3 INSULATION
PROFILE L1
WINDOW
HOOK T6/V3 sx
72
HOOK T6/V3 dx
STANDARD HORIZONTAL JOINT
73
10
Panariagroup > ventilated faรงades
Slab mounting operation
Horizontal section - Scale 1:4
Vertical section - Scale 1:4
INSULATION
Standard horizontal closing solution
PROFILE L8
LUNA VISTA SYSTEM PANARIAGROUP LAMINATED PORCELAIN STONEWARE
HOOK T6/V3
INSULATION
HOOK T6/V3 sx PROFILE L1
12.8
74
STRUCTURAL ADHESIVE ADESIVO STRUTTURALE
75
11
Panariagroup > ventilated façades
VENERE SORMONTATO SYSTEM PANARIAGROUP PORCELAIN STONEWARE
SYSTEM TYPE:
SYSTEM COMPONENTS
Visible hooks
The “VENERE SORMONTATO” system consists of the following elements: • Extruded “CV1” profile in aluminium alloy EN 6060 T5 (or similar, according to requirements); • Support hooks of the tiles “V3et” and “V3” stainless steel EN 1.4310 (AISI 301); • Fixing springs of the hooks to the profile “CV1” type “V2” in stainless steel EN 1.4310 (AISI 301) treated; • Standard support brackets “A12” and “B12” made from extruded aluminium EN 6060; • Stainless steel screws, for fixing “CV1” profile to the brackets; • Anchoring dowels for fixing brackets to the wall, mechanically or with chemical resin as necessary; • Neoprene sealing strip to improve the bonding between the tiles and the hooks and profiles, of a different thickness as required; • “Lana” springs in hardened and tempered stainless steel, to support the insulation panels applied to the wall, when required.
TYPE OF CLADDING TILES: Panariagroup porcelain stoneware tiles with thickness from 9 to 20 mm OPERATIONS CARRIED OUT ON THE TILE: None CLADDING TILE SIZES:
SYSTEM DESCRIPTION
All sizes of Panariagroup product range
The system consists of a mounted aluminium vertical profile “CV1” according to the width of the tile, plus the joint of the project. The vertical profile “CV1” is shaped to accommodate without drilling the following accessories: • wall fixing brackets screwed with stainless steel bolts, according to project pitch; • the hooks “V3et” and “V3” for the support of the tile and the corresponding fixing springs “V2” should be inserted with an appropriate tool in the slot of the vertical profile, according to the height of the cladding tiles plus the project joints (which are not visible); • the supporting springs of the insulating panel, when necessary, snapped in. As there are no holes, no damage is done to the surface protection (caused by oxidation or electrocoloring) and this increases the life-cycle of the profiles.
In partnership with DALLERA
The main characteristic of this “Venere Sormontato” system is that each tile is installed in an almost-vertical position, so that the upper tile overlaps the inferior tile by about 1 cm. The tiles can be installed on the cladding very simply, without any further work on their surfaces or edges, by the supporting hooks which are visible from outside the façade. If needed, the hooks can be painted the same colour of the tiles so that they are not visible not even from a small distance from the cladding itself. Each tile is bonded with the hooks and the vertical profile using neoprene gasket strips of adequate thickness and silicone drops, when needed. When all the components are put in place, each tile can be installed or dismantled one at a time. The supporting structure allows any type of adjustment; it is able to protect from wind loads and allows the thermal expansion of the different components. SYSTEM SIZES: • The standard distance between the wall and the internal face of the tiles is 110 mm, with a standard adjustment range of ± 25 mm. • The standard thickness of Panariagroup porcelain stoneware tiles for this type of system is from 9 to 20 mm.
76
77
11
Panariagroup > ventilated faรงades
VENERE SORMONTATO SYSTEM PANARIAGROUP PORCELAIN STONEWARE Standard components
Standard solution for mid-section
PROFILE CV1
Vertical section - Scale 1:4
SINGLE BRACKET
DOUBLE BRACKET
SPRING V2
HOOK V3ET GANCIO V3ET
HOOK V3
N.B: The actual components may be modified in the design phase.
Standard solution for roof finishing
Standard solution for floor end
Vertical section - Scale 1:4
Vertical section - Scale 1:4
PROFILE CV1
PROFILE CV1
CLOSING ELEMENT
ANTI-INSECT CLOSING ELEMENT
78
DISTANCE ACCORDING TO PROJECT SPECIFICATIONS
79
11
Panariagroup > ventilated faรงades
VENERE SORMONTATO SYSTEM PANARIAGROUP PORCELAIN STONEWARE Standard solution for window head
Standard solution for windows head
Vertical section - Scale 1:4
Horizontal section - Scale 1:4
PROFILE CV1
WINDOW FRAME
PROFILE CV1
WINDOW
WINDOW
HEAD
NEOPRENE GASKET
Standard solution for mid-section
Vertical section - Scale 1:4
Horizontal section - Scale 1:4
WINDOW
Standard solution below windowsill
PROFILE CV1
WINDOWSILL
PROFILE CV1
NEOPRENE GASKET
80
NEOPRENE GASKET VERTICAL JOINT
81
11
Panariagroup > ventilated faรงades
VENERE SORMONTATO SYSTEM PANARIAGROUP PORCELAIN STONEWARE Tile mounting operation
Horizontal section - Scale 1:4
Vertical section - Scale 1:4
PROFILE CV1
PROFILE CV1
NEOPRENE GASKET
Standard solution for external angle
X PROFILES FOR ANGLES NEOPRENE GASKET
Standard solution for internal angle
PROFILE CV1
NEOPRENE GASKET
Horizontal section - Scale 1:4
PROFILE CV1
NEOPRENE GASKET
82
83
12
Panariagroup > ventilated façades
VENERE SORMONTATO SYSTEM PANARIAGROUP LAMINATED PORCELAIN STONEWARE
SYSTEM TYPE:
SYSTEM COMPONENTS
Visible hooks
The “VENERE SORMONTATO” system consists of the following elements: • Extruded “CV1” profile in aluminium alloy EN 6060 T5 (or similar, according to requirements); • Support hooks of the slabs “V3et” and “V3” stainless steel EN 1.4310 (AISI 301); • Fixing springs of the hooks to the profile “CV1” type “V2” in stainless steel EN 1.4310 (AISI 301) treated; • Standard support brackets “A12” and “B12” made from extruded aluminium EN 6060; • Stainless steel screws, for fixing “CV1” profile to the brackets; • Anchoring dowels for fixing brackets to the wall, mechanically or with chemical resin as necessary; • Neoprene sealing strip to improve the bonding between the slabs and the hooks and profiles, of a different thickness as required; • “Lana” springs in hardened and tempered stainless steel, to support the insulation panels applied to the wall, when required.
TYPE OF CLADDING SLABS: Panariagroup laminated porcelain stoneware 3Plus or 5Plus slabs OPERATIONS CARRIED OUT ON THE SLAB: None CLADDING SLAB SIZES:
SYSTEM DESCRIPTION
Maximum size 300x50 cm
The system consists of a vertical aluminium profile “CV1” according to the width of the slab, plus the joint of the project. The vertical profile “CV1” is shaped to accommodate without drilling the following accessories: • wall fixing brackets screwed with stainless steel bolts, according to project pitch; • the hooks “V3et” and “V3” for the support of the slab and the corresponding fixing springs “V2” should be inserted with an appropriate tool in the slot of the vertical element, according to the height of the cladding slab and joint of the project (which is not visible); • the supporting springs of the insulating panel, if necessary, snapped in. As there are no holes, no damage is done to the surface protection (caused by oxidation or electrocoloring) and this increases the life-cycle of the profiles.
In partnership with DALLERA
The main characteristic of this “Venere Sormontato” system is that each slab is installed in an almost-vertical position, so that the upper slab overlaps the inferior slab by about 1 cm. The slabs can be installed on the cladding very simply, without any further work on their surfaces or edges, by the supporting hooks which are visible from outside the façade. If needed, the hooks can be painted the same colour of the slabs so that they are not visible not even from a small distance from the cladding itself. Each slab is bonded with the hooks and the vertical profile using neoprene gasket strips of adequate thickness and silicone drops, when needed. When all the components are put in place, each slab can be installed or dismantled one at a time. The supporting structure allows any type of adjustment; it is able to protect from wind loads and allows the thermal expansion of the different components. SYSTEM SIZES: • The standard distance between the wall and the internal face of the slabs is 110 mm, with a standard adjustment range of ± 25 mm. • The standard thickness of Panariagroup laminated porcelain stoneware slabs for this type of system is 3.5 or 5.5 mm.
84
85
12
Panariagroup > ventilated faรงades
VENERE SORMONTATO SYSTEM PANARIAGROUP LAMINATED PORCELAIN STONEWARE Components
Standard solution for mid-section Vertical section - Scale 1:4 SPRING V2
CV1 Profile
PROFILE CV1
SPRING V2 HOOK V4 HOOK V4 DOWEL
BRACKET
SPRING V2 V2+V3et
BOLTS
BOLTS
12.5 11.0
SPRING V2 HOOK V4 HOOK V4
Standard solution for floor end
Vertical section - Scale 1:4
Vertical section - Scale 1:4
PROFILE CV1
CV1 Profile
Standard solution for roof finishing
11.0 12.5
ANTI-INSECT CLOSING ELEMENT
86
DISTANCE ACCORDING TO PROJECT SPECIFICATIONS
X
V2+V3et
Insect blocking element
According to project
87
12
Panariagroup > ventilated faรงades
VENERE SORMONTATO SYSTEM PANARIAGROUP LAMINATED PORCELAIN STONEWARE Standard solution for window head
Standard solution for window head
Vertical section - Scale 1:4
Horizontal section - Scale 1:4 11.0 12.5
Side
CV1 Profile
Window
Window
V2+V3et
12.5
head
CV1m profile
V2+V3et
Gasket neoprene
Standard solution for mid-section
Vertical section - Scale 1:4
Horizontal section - Scale 1:4
Window
Standard solution below windowsill
11.0
V2+V3
12.5
CV1 Profile
Windowsill
CV1 Profile V2+V3et
V2+V3et
V2+V3et
11.0 Gasket neoprene
88
X Vertical joint: according to project
Gasket neoprene
89
12
Panariagroup > ventilated faรงades
VENERE SORMONTATO SYSTEM PANARIAGROUP LAMINATED PORCELAIN STONEWARE Standard solution for external angle
Slab mounting operation
Horizontal section - Scale 1:4
Vertical section - Scale 1:4
12.5
V2+V3et
CV1m profile
V2+V3et
CV1m profile
11.0
12.5
Gasket neoprene
neoprene
V2+V3et
Profile X for angles
Gasket neoprene
Standard solution for internal angle Horizontal section - Scale 1:4 11.0
90
12.5
11.0
V2+V3et
CV1m profile
Gasket neoprene
V2+V3et
CV1m profile
Gasket neoprene
12.5
91
13
Panariagroup > ventilated façades
SIRIO SYSTEM PANARIAGROUP LAMINATED PORCELAIN STONEWARE
SYSTEM TYPE:
SYSTEM COMPONENTS
Visible hooks
The “SIRIO” system consists of the following elements: • Extruded “ET1” and “ET1m” profiles in aluminium alloy EN 6060 T5 (or similar, according to requirements); • Aluminium rivets EN 6060 T5 with large head to fix the slab to the profile (or other fasteners, according to project); • Standard support brackets “A12” and “B12” made from extruded aluminium EN 6060; • Screws for fixing “ET1” and “ET1m” profiles to the brackets, stainless steel class A2; • Anchoring dowels for fixing brackets to the wall, mechanically or with chemical resin as necessary; • Neoprene sealing strip to improve the bonding between the slabs and the profiles, of a different thickness as required;
TYPE OF CLADDING SLABS: Panariagroup laminated porcelain stoneware 3Plus or 5Plus slabs OPERATIONS CARRIED OUT ON THE SLAB: Through drilling CLADDING SLAB SIZES: Maximum size 300x100 cm In partnership with DALLERA
SYSTEM DESCRIPTION The system consists of a vertical profile of aluminium “ET1” placed according to the width of the slab and the joint of project, and a profile “ET1m” in intermediary points. Their pitch is determined by the width of the slabs and installation requirements. The vertical profiles “ET1” and “ET1m” are shaped in such a way as to: • be attached to the wall fixing brackets with stainless steel bolts, according to project pitch; • provide an adequate surface to support the slabs, and a solid element for the application of the rivets (or other fasteners) for the fixing of the slabs. Profiles can be supplied plain or electro-coloured, on request. Each slab is bonded with the hooks and the vertical profile using neoprene gasket strips of adequate thickness and silicone drops, when needed. The main characteristic of the “Sirio” system is that the slabs are mounted by means of rivets that are visible from outside; therefore slabs must be drilled before laying. The drilling diagram of the slabs with the sizes of holes and their positions is made in line with the technical instructions given by the manufacturer of the slabs to guarantee their optimal utilization and their longest life. Depending on the architect’s instructions, rivets (or the other fixing materials) can be plain or painted in the same colour of the slabs to appear almost invisible from very close. SYSTEM SIZES: • The standard distance between the wall and the internal face of the slabs is 110 mm, with a standard adjustment range of ± 25 mm. • The standard thickness of Panariagroup laminated porcelain stoneware slabs for this type of system is 3.5 or 5.5 mm.
92
93
13
Panariagroup > ventilated faรงades
SIRIO SYSTEM PANARIAGROUP LAMINATED PORCELAIN STONEWARE Components
Standard solution for mid-section Vertical section - Scale 1:4 PROFILE ET1 DOWEL
BRACKET
GASKET Wall slab Neoprene tape
BOLTS
Rivets or other suitable fasteners
BOLTS
According to project
~4,0
X
~4,0
RIVETS
B
LA
S ING
RIVETS
Horizontal joint: according to project
According to project
Rivets or other suitable fasteners
D AD
Neoprene tape Wall slab
ET1m Profile
CL
11.0
0.5
11.5
Standard solution for roof finishing
Standard solution for floor end
Vertical section - Scale 1:4
Vertical section - Scale 1:4
~4,0
roof flashing
According to project
Rivets or other suitable fasteners Neoprene tape
ET1m Profile
Wall slab
Wall slab Neoprene tape
0.5
Insect blocking element
~4,0
11.0
According to project
X
ET1m Profile
Rivets or other suitable fasteners
According to project
11.5
94
95
13
Panariagroup > ventilated faรงades
SIRIO SYSTEM PANARIAGROUP LAMINATED PORCELAIN STONEWARE Standard solution for window head
Standard solution for window head
Vertical section - Scale 1:4
Horizontal section - Scale 1:4 0.5
11.0 11.5
Rivets or other suitable fasteners Side
ET1m Profile
Window
Wall slab Neoprene tape
~4,0
Rivets or other suitable fasteners
Rivets or other suitable fasteners
Window
head
According to project
~3,4
Wall slab Neoprene tape Rivets or other suitable fasteners
According to project
Standard solution for mid-section
Vertical section - Scale 1:4
Horizontal section - Scale 1:4
Window
Standard solution below windowsill
~4,0
Windowsill
According to project
Rivets or other suitable fasteners Neoprene tape
11.0 11.5
96
0.5
Wall slab Neoprene tape Rivets or other suitable fasteners
~4,0
11.0 ~4,0
ET1m Profile
0.5
ET1m Profile
ET1 Profile
11.5
Wall slab
X Vertical joint: according to project
97
13
Panariagroup > ventilated faรงades
SIRIO SYSTEM PANARIAGROUP LAMINATED PORCELAIN STONEWARE Standard solution for external angle
Slab mounting operation
Horizontal section - Scale 1:4
Vertical section - Scale 1:4
Rivet 11.5 11.0
Neoprene
ET1m Profile
~4,0
ET1a Profile
According to project
0.5
~4,0 According to project
Rivet
Standard solution for internal angle
Neoprene
11.5 11.0
11.0 11.5
0.5
According to project
Rivets or other suitable fasteners Neoprene tape Wall slab
Rivets or other suitable fasteners Neoprene tape Wall slab 0.5
ET1m Profile
0.5
Wall slab Neoprene tape Rivets or other suitable fasteners
~4,0
Horizontal section - Scale 1:4
11.5 11.0
ET1m Profile
98
99
14
Panariagroup > ventilated façades
SIMPLE SYSTEM PANARIAGROUP PORCELAIN STONEWARE
SYSTEM TYPE:
SYSTEM COMPONENTS
Visible hooks
The “Simple” system consists of the following elements: • Extruded vertical profile “ VP LT / VP L” made in aluminum alloy EN 6063 T66; • Fixing point holder “LFH” made in aluminum alloy EN 6063 T66; • Sliding point holder “LSH” made in aluminum alloy EN 6063 T66; • Visible hanger “ BRV / BRV-C / BRV-R / BRV-L” made in stainless steel AISI 304; • Rivets made in stainless steel AISI 304 for connection of hanger “BRV / BRV-C/BRV-R / BRV-L” to profile “VP LT/VP L”; • Insulating barrier pad “THERMO-PAD” made in PA.
TYPE OF CLADDING TILES: Panariagroup porcelain stoneware tiles with thickness from 9 to 20 mm OPERATIONS CARRIED OUT ON THE TILE: None CLADDING TILE SIZES: All sizes of Panariagroup product range In partnership with FISCHER
SYSTEM DESCRIPTION The system provide the use of vertical profile VP, placed according to the width of the tile, and fastened to the support by means of wall holders LFH/LSH with stainless steel A2 rivets. The wall holders are designed according to UNI 11018 and allow the thermal expansion of vertical profile. The fixing to the support is assured by fischer mechanical or chemical anchors. The vertical profile is equipped with a guide for maximum excursion when inserted in the LFH and LSH wall holder. The tiles are anchored to the vertical profile by means of visible hanger fastened with rivets. The visible hangers can be painted with the same color of the tile to camouflage them in the facade. The system is suitable to realize a facade with a regular pattern of tiles. SYSTEM SIZES: • With the different wall holders (LFH /LSH) the standard distance between the wall and the internal face of the tiles can vary between 70 mm and 225 mm. • The standard thickness of Panariagroup porcelain stoneware tiles for this type of system is from 9 to 20 mm.
100
101
14
Panariagroup > ventilated faรงades
SIMPLE SYSTEM PANARIAGROUP PORCELAIN STONEWARE Components
Standard solution for mid-section Vertical section - Scale 1:5
N.B: The actual components may be modified in the design phase.
102
Standard solution for roof finishing
Standard solution for floor end
Vertical section - Scale 1:5
Vertical section - Scale 1:5
103
14 SIMPLE SYSTEM PANARIAGROUP PORCELAIN STONEWARE Follow us on:
Cotto d’Este Standard solution porcelain for internal tile angle Vertical section - Scale 1:5
Quality management system
Environmental management systems of production sites
GESTIONE AMBIENTALE VERIFICATA reg. n. I-000309
GESTIONE AMBIENTALE VERIFICATA reg. n. I-000401
GESTIONE AMBIENTALE VERIFICATA reg. n. I-000239
Plant of Finale Emilia (MO)
Plant of Fiorano Modenese (MO)
Plant of Toano (RE)
Panariagroup Industrie Ceramiche S.p.A. is a member of the U.S. Green Building Council and Green Building Council Italia
Cotto d’Este Standard solution porcelain for external tile angle Vertical section - Scale 1:5
The instructions in this document are fruit of the research and the direct experience of Panariagroup Industrie Ceramiche S.p.A. and are to be considered purely indicative, as it is impossible to predict all the environmental and application variables. Non-contractual document. Panariagroup Industrie Ceramiche S.p.A. reserves the right to change the characteristics and range of products and application systems listed in this publication at any time without notice.
January 2018 104
panariagroup.it