Goltens
instruction manual and sparepart list
Oslo AS
goltens MultiPurpose high pressure pump g1700 MP
Technical Information Weight: 14 Kg Dimension: 420 x 280 x 220 Max oil pressure rating (2 minutes): 1700 bar Max continuous working (pressure/automatic): 1050 bar Max air drive pressure: 8,62 bar / 125 PSI Working ratio air: oil 1:220 Output flow against 0 bar (kp/cm2): 0,5 litre/min.
Strømsveien 195-197, 0668 Oslo, Norway Tel: +47 22 88 39 30 • Fax: +47 22 88 39 31 E-mail: oslo@goltens.com • www.goltens.no Side 1
G1700 MP Parallell krets / Parallel Circuit
A
Pos. 54. High pressure man.
Parallell krets Åpne stengeventil (A) på fordelingsstykket. Oljetrykksmanometeret (pos. 54) vil vise trykk ut fra pumpen.
Parallel Circuit Open valve (A) on manifold completely. Oil pressure gauge (pos. 54) indicates pressure from the pump.
A
Fordelingsstykke er montert på baksiden av pumpen.
Serie krets / Serial Circuit
Manifold is reacheable from backside of the pump.
A
Pos. 54. High pressure man.
Seriell krets Lukk stengeventil (A) på fordelingstykket. Oljetrykksmanometret (pos. 54) vil vise trykk etter at hele kretsen er trykksatt. Retur trykket tilbake til pumpa, etter kretsen, aktiverer manometeret. OBS! Alle koblinger i kretsen MÅ være tilkoblet for at oljetrykkmanometeret skal gi utslag OBS! Side 2
Serial Circuit Close Valve (A) on manifold completely. Oil Pressure gauge indicates pressure AFTER the tool circuit only. Caution! All couplings MUST be connected making a full circuit before increasing the pressure. Caution!
Instruction manual 1. Fill oiltank with approx. 4l. pure hydraulic
7. Close bleeding screw on hydraulic tool and
oil through pos. no. 22.
pressure will rice. Watch oil pressure manometer pos. 54 and make final adjustments with air pressure regulator pos. 31 to obtain the desired oil pressure. The G- pump will now automatically keep the pressure even with a minor leakage in the hydraulic system.
2. Connect air hose to pos. 39. Max. air pressure 8 bar or 115 PSI.
3. Circulate oil in pump unit by opening air stop valve pos 44 and oil release valve pos 01.
4. Preset desired oil pressure with air pressure r足 egulator pos 31 according to corresponding scale on air manometer pos 52. Always preset this lower than the actual needed pressure.
5. Connect high pressure hose from hyd足raulic tool
8. If not sufficent air pressure is available to obtain the desired oil pressure, use the hand pump in addition.
9. The safety valve is adjusted in accordance with the release pressure shown on the label attached to the back side of G-pump.
to pos. 14, then close oil release valve pos. 01.
6. If bleeding is necessary, circulate oil through
10. Pos. 12 is a high pressure outlet for eventual extra manometer or extra high pressure hose. Thread in bore M 16 x 1,5 with a 5 mm diam. seat 600.
hydraulic tool and back to oil tank via transparent plastic hose connected to pos. 20 on pump unit.
Oiltype: Hydraulic oil Rando 32. Your G-pump is a precision tool and we advice you to use and store it accordingly. Pos. 31. Air regulator. Pos. 54. High pressure man. Hand pump.
Pos. 39. Air connection.
Pos. 01. Oil release valve Pos. 44. Air stop valve.
Pos. 20. Return oil connection.
Pos. 52. Air pressure man.
Pos. 14. High pressure outlet.
Pos. 70. High pres. pump.
Pos. 12. Extra high pressure outlet.
Hand pump lever
Pos. 22. filler breather filter
Serial number
Side 3
Part list G1700 MP Ordering code: 72-11XX (XX=pos.no.) Example pos. 16: 72-1116
11B
Side 4
ITEM
DESCRIPTION
72-1101 Valve 120A 72-1101A Nut 72-1101B Washer 72-1101C Adapter 72-1101D HP tube 72-1102 Adapter 72-1103 Ring 72-1105 Plate 72-1106 Adapter 72-1107 Tube 72-1109 Washer 72-1110 Screw 72-1111B Manifold 1700 MP 72-1112 Screw 72-1113 HP tube 72-2414 Quick coupling oil male G1700 MP 72-1115 Adapter 72-2416 HP tube 72-1117 Lock-nut 72-1118 Suction pipe 72-1119 Washer 72-1120 Sounding rod 72-1121 Gasket 72-1122 Filter 72-1122B Screws (2 pcs) 72-1124 Gasket 72-1125 Handle 72-1126 Screw 72-1127 Clips 72-1127A Screw 72-1127B Screw 72-1127C Nut 72-1128 Screw 72-1129 Screw 72-1130 Air pressure plate 72-1130A Plate push/pull 72-1131 Air pressure regulator 72-1132 Nipple 72-1133 Elbow 72-1137 Screw 72-1138 Bracket 72-1139 Quick coupling air male 72-1140 Quick coupling air female 72-1141 Elbow 72-1142 Tube 72-1143 Elbow 72-1144 Valve air 150A 72-1145 Plate air stop valve 72-1147 Tube 72-1149 Elbow
ITEM
DESCRIPTION
72-1150 Tube 72-1151 Elbow 72-2452 Manometer 0-10 bar 72-1152A Screws (3 pcs) 72-2453 Plate air pressure 72-2454 Manometer 0-2000 bar MP1700 72-1154A Screws (3 pcs) 72-1160 Air pressure regulator complete 72-1162 Lable 72-1163 Plate max working pressure 72-1164 Plate pure hydraulic oil 72-2466 Quick coupling female G1700 MP 72-1167 Hose 2 m 72-1168 Hose clip 72-1170 Air/hydraulic pump M188 72-1172 Cabinet 72-1173 Oil tank 72-2475 Nipple G1700 72-2476 Pump complete G1700 MP 72-2481 HP hose 3,0 M* G1700 RED 72-1185 HP distributor 72-1197 Screw 1,9x5 UBS Rivets 72-1198 Screw 2,5x3 UBS Rivets * Other hose lengths can be delivered on demand.
Side 5
Part list air driven hydraulic pump Seal kit hydraulic comprises Seal kit pheumatic comprises Inlet valve assy comprises Outlet valve assy comprises
pos no: 28, 29, 30, 44, 45, 48, 49, 50, 51, 52 pos no: 4, 5, 6, 8, 10, 14, 16, 17, 19, 23 pos no: 33, 45, 47, 48, 49, 50, 52 pos no: 32, 45, 47, 48, 49, 50, 51, 52
ITEM DESCRIPTION 722301 Top cap 722303 Plunger 722307 Tube 722309 Pilot valve 722311 Plug 722313 Sleeve 722315 Spool 722318 Air piston 722320 Spring support 722321 Spring 722322 Cylinder tube 722334 Exhaust cap 722325 Silencer
1 1 1 1 1 1 1 1 1 1 1 1 2
Side 6
PCS.
ITEM DESCRIPTION PART NO. 722326 Screw 2 722327 Bottom cap 1 722331 Spacer 1 722353 Diaphgram 1 722354 Bolt 4 722355 Washer 4 722357 Cover 1 722360 Seal kit hydraulic 1 722361 Seal kit pneumatic 1 722397 Inlet valve assy 722398 Outlet valve assy
PCS.
Contact information: Strømsveien 195-197, 0668 Oslo, Norway Tel: +47 22 88 39 30 • Fax: +47 22 88 39 31 E-mail: oslo@goltens.com • www.goltens.no
Goltens Oslo AS kan vise til mer enn 60-års erfaring i verkstedsbransjen. Med et utgangspunkt i skipsindustrien har kvalitet, punktlighet og høy grad av fleksibilitet vært vårt varemerke. Dette er selvsagt videreført i alle våre tjenester mot den landbaserte industri og en høyt kvalifisert og dyktig arbeidstokk på ca 30 mann med During the last 60 years, Goltens moderne verktøymaskiner står til Oslo AS has been a major supplier enhver tid rede til å ta fatt på and service provider both to the oppgaver som måtte komme shipping and land based industry. opp. Lyse og romslige lokaler, Goltens Oslo AS, founded on the beliggende sentralt rett utenbase of the shipping industry, has for Oslo sentrum, gir oss become a business trade mark in anledning til å betjene quality, punctuality, and flexibility. våre kunder på en This is has also been implemented into rask og effektiv our on-shore business, employing 40 måte. dedicated colleagues offering high quality and standards to this industry also. Located in Oslo we are able to serve our customers in a swift and efficient way.
Side 7
Menu
The services listed below are all carried out by in house equipment and expertise. Our management is capable and experienced in tying these services together in small and large projects to suit the owners needs. For other services not listed, we co-operate with specialized companies so the owner can select to have one main contractor to tie the project together.
specialized services
• Crankshaft Grinding • in Situ • in Workshop • Line Boring of Engine Bed Plates
• Landing Surfaces in Situ • Alignment and Chocking • Laser based alignment • Broken Stud Removal
in Situ or in Workshop reconditioning services
• Centrifugal Casting of White Metal Bearings • Fuel Injectors and Pumps • Connecting Rods • Exhaust Valves / Seats
• Cylinder Heads • Pistons • Turbochargers • Governors
trading/supply
repair services (including voyage repairs) • Diesel Engines • Steam Turbines • Shaft Lines • Propellers & Rudders • Winches • Valves, Pumps, COW Machines • Hatch covers • Ro/Ro Equipment
• Hydraulic Pumps • Fuel equipment • Miscellaneous parts • Spare parts for Aker cranes • Automation Systems • Electrical Systems • Hydraulic Systems • Steel Structures • Pipelines • Blasting & Painting • Cleaning • Staging • Service on Aker cranes (and others)
Goltens UK
Goltens Greece
(Mumbai) Goltens India (Chennai)
Side 8
300588. Bl. 916-4. 10.09. HA Grafisk a.s / PRINFO Kolbotn. 100.
• MKK and Alfa Laval Separator Spares • Bearings • Diesel engine parts • Piston Rings