Stx 6600 manual by Polaris Controls

The STX 6600 is a straight column Line Array featuring six high power 6.5â&#x20AC;? custom designed neodymium woofers and six advanced design planar magnetic Ribbon drivers in a coax configuration with a unique waveguide for wide 110 degrees horizontal coverage. Ultra-fast transient response and higher instantaneous peak level for faithful signal reproduction and improved dynamic range. The highly controlled vertical dispersion of the array and excellent coupling of the ribbon drivers at high frequency yields the ultimate hi fidelity long throw system. True line array performance provides dramatically increased intelligibility in highly reverberant spaces. Single box construction with integrated fly points and internal passive crossover for lower cost installation. Improved front to back SPL over the entire audience area, typically +/- 2db

Stix and Drums LLC 1990 N. McCulloch Blvd. Ste. D222 Lake Havasu City, AZ Voice: 928.733.6002 Fax: 928.453.5550 info@stixanddrums.com www.stixanddrums.com

Introduction Thank you for choosing Stix & Drums. When your speakers are installed and used properly, you can expect exceptional aural performance and years of trouble free service. Please read this manual thoroughly prior to installation.

Safety Responsibilities and Liability Information in this guide is meant only for the purpose of using the AmbiSonic Systems supplied mounting equipment. All other rigging and/or structure support including wall securing hardware is considered part of the venue and/or end-user supplied equipment and is not addressed in this guide. AmbiSonic Systems assumes that a working knowledge of accepted rigging practices and safety will be applied to all rigging materials and practices employed. All rigging or wall mounting should be performed by a professional installer or installation company and should follow all state and local building codes. All fasteners should be rated at a minimum of 3-5 times the actual determined load. All walls are not created equal (drywall, masonry, wood, etc.) In some instances it will be necessary to install “Backing” plates or other reinforcement to assure proper mounting. Remember that the weakest component determines the safety of the entire rigging assembly. Prior to securing the array, always inspect all hardware components for wear, deformations, corrosion and missing or damaged parts. Also confirm that the venue attachment points are suitably load rated for the array. No information contained in this guide is intended as a warranty on the part of AmbiSonic Systems. Users assume all responsibility for the appropriate use of AmbiSonic Systems supplied rigging hardware and follow at a minimum all applicable laws and regulations in force for each venue. Anyone using this information assumes all liability arising from it’s use. Product abuse, use of the product not in accordance with AmbiSonic Systems instructions or use in an application which the product has not been designed for is not covered under any AmbiSonic Systems warranty nor is AmbiSonic Systems liable for any loss or damage.

Stix and Drums LLC 1990 N. McCulloch Blvd. Ste. D222 Lake Havasu City, AZ Voice: 928.733.6002 Fax: 928.453.5550 info@stixanddrums.com www.stixanddrums.com

Attaching Coupling Brackets (BKT-CP66) For multiple stacked arrays

Remove the M10 Flathead Screws (4 places each side)

Coupling Brackets (BKT-CP66) (2)

Attach the coupling plates with the removed M10 flathead screws

All attachment points for coupling brackets are reinforced with internal steel brackets for maximum strength and reliability.

Wall Mounting Kit (BKT-WM66) For multiple stacked arrays

Upper Bracket Assembly

Upper Bracket

Pivot Right Pin

Pivot Left Pin

Down-angle adjustment holes

Rotation Locking Fastener Wall Mounting Bracket

Lower Bracket Assembly

Pivot Right Pin Lower Bracket

Pivot Hole Pivot Left Pin

Rotation Locking Fastener Wall Mounting Bracket

Attaching Upper and Lower Wall Mounting Brackets Upper Bracket Install the upper bracket to the STX6600 by first removing the top rear M10 flathead screws from the enclosure, then place the upper bracket in the predetermined down angle position (see Fig.1), insert the supplied M10 button head screws through the appropriate hole in the bracket and secure the screws.

Down-angle Adjustment Upper holes labeled “BOX 2” are for down-angle adjustment of 0 - 2.5 degrees for a column stack of two (2) STX6600 Lower holes labeled “BOX 3” are for down-angle adjustment of 0 - 2.5 degrees for a column stack of three (3) STX6600

Fig. 1

BOX 2 BOX 3 0

0.5

1.0

1.5

2.0

2.5

Lower Bracket Install the bottom bracket to the STX6600 by removing the bottom rear M10 flathead screws, then place the bottom bracket in position as shown, insert the supplied M10 button head screws through the bracket and tighten. If the column will have any down angle, the screws should not be tightened completely as they are the pivot point for rotation. Once the column has been mounted and adjusted for angle, you can then tighten the pivot screws.

Wall Mounting Wall Mount Bracket Spacing

Wall Mount Hole Spacing 10.945

STX6600

7.000

71.91

69.70

2.277

1.462

0.3

2.462

STX6600

Wall Mount Bracket Right & Left Hand Left Rotation

STX6600

Pivot

Dimensions shown are from the top of each wall mount bracket.

Right Rotation

Pivot

STX6600

111.20

STX6620

Typical Column Examples

STX6600 & STX6620

(2) STX6600

(3) STX6600

Attaching MM-120 Wall Mounting Brackets 3.44 2.75 2.00

5.27 3.75

2.50

.41 4X

.39 6X 4.25

9.00 4.00

7.75

6.88

5.00 4.25

.406 2X

2.00

.38 4X .41 X .50 SLOT

MM-120 WITH WP-16 OPTIONAL STUD PLATE

Wall Mount Plate

.41X.72 SLOT 2X

Speaker Mounting Plate

13.52 10.88

14.38 50° MAX.

9.00

FULLY EXTENDED ARM AT MAX. DOWN TILT ANGLE

Fully Extended - Max. Down Tilt

2.76 70

15° MAX. FULLY STOWED ARM AT MAX. UP TILT ANGLE

5.00 127

16.64

Fully Stowed - Max. Up Tilt

MM-120 ATTACHED TO STX6600

All wall mounting should be performed by a professional installer or installation company and should follow all state and local building codes. All fasteners should be rated at a minimum of 3-5 times the actual determined load. All walls are not created equal (drywall, masonry, wood, etc.) In some instances it will be necessary to install “Backing” plates or other reinforcement to assure proper mounting. WARNING: Mounting and/or suspension of loudspeakers requires experienced professionals. Improperly installed loudspeakers can result in property damage, personal injury and/or liability to the installing contractor. Always install safety cables.

REAR MOUNTED ILLUSTRATION (8" ARM TUBE) 2-7090 SPEAKER ADAPTER PLATE 1/8" THICK STEEL PLATE

2-7086 PIVOT BRACKET 1.75 SQ X .12 TUBE

2-7097 TRUSS HEAD BINDING POST SCREW 3/8" DIA. BARREL X 2.063" LONG X 1/4-20 THREAD 2-7088 PIVOT U-BRACKET SCREWED TO TUBE

Attaching MM-060 Wall Mounting Brackets 2-7095 THREADED ROD FOR REAR AND BOTTOM MOUNTED

60 lbs. maximum load C

3.75 2.75

DIMENSIONS

12.00

2.00

7.25

NYLON WASHER 3/8 ID X 1.25 OD (2X)

5.00

45°

4.00

6.00

4.25

3.75 2.75 2.00 1.56

8.00 6.00

45° MAX

4.25 5.00

2.25

.88

.50

@45 DEGREE TILT

45 degrees Max. Down Tilt

2.50

3.58

1.88

Speaker Mounting2.25 Plate

45 degress Max. Up Tilt A

Wall Mount Plate

PROPRIETARY AND CONFIDENTIAL

REVISIONS

Notes: Unless Otherwise Specified

ZONE REV.

DESCRIPTION

DRAWN

DATE

REVISED CABLE PAS THRU HOLE LOCATIONS. ADDED BOTTOM MOUNTED ILLUSTRATIONS. ADDED WALL PLATE COVER

TBA

04/30/13

REVISED WALL PLATE ASSY AND COVER

TBA

05/08/13

APPROVED

THIS DRAWING IS THE PROPERTY OF ALLEN PRODUCTS CO. AND EMBODIES A PROPRIETY DESIGN ORIGINATED BY ALLEN PRODUCTS CO. ALL DESIGN, MANUFACTURE, REPRODUCTION, USE AND SALE RIGHTS REGARDING THE SAME ARE EXPRESSLY RESERVED. THIS DRAWING MAY NOT BE REPRODUCED OR INFORMATION HEREIN TRANSMITTED IN ANY WAY WITHOUT WRITTEN CONSENT FROM ALLEN PRODUCTS CO. ALL PATENT RIGHTS HERETO ARE EXPRESSLY RESERVED BY ALLEN PRODUCTS CO. SIGNAL HILL, CALIFORNIA

UNLESS OTHERWISE S

DIMENSIONS ARE IN IN TOLERANCES: FRACTIONAL ANGULAR: MACH TWO PLACE DECIMAL THREE PLACE DECIMA INTERPRET GEOMETRIC TOLERANCING PER: MATERIAL FINISH

THIRD ANGLE PROJECTION

DO NOT SCALE DRA

FILE LOCATION: E:\ENGINEERING\PROJECTS-PRELIMINARY DRAWINGS\PROJ-301-UP\PROJ-502 M

5.00 127

2.75 70

MM-060 ATTACHED TO STX6600 All wall mounting should be performed by a professional installer or installation company and should follow all state and local building codes. All fasteners should be rated at a minimum of 3-5 times the actual determined load. All walls are not created equal (drywall, masonry, wood, etc.) In some instances it will be necessary to install “Backing” plates or other reinforcement to assure proper mounting. WARNING: Mounting and/or suspension of loudspeakers requires experienced professionals. Improperly installed loudspeakers can result in property damage, personal injury and/or liability to the installing contractor. Always install safety cables.

Fly Points Fly points (4) are positioned on the top of each enclosure and (1) located at the bottom center.

Top fly points (4)

Bottom rear fly point (1) (Pull back adjustment)

All fly points are reinforced with internal steel brackets for maximum strength and reliability

Remove the appropriate M10 flathead screws. Replace M10 flathead screws with M10 Forged Steel Eye-bolts.

Top fly points for hanging.

Bottom rear fly point for down-angle adjustment (Pull back adjustment)

(Use only M10 Forged Steel Eye-bolts)

STX 6600 Specifications 7.165 182

1.693 43

M10 (17 Plc's.) Loop Output

Input

4.724 120

1.693 43

Input 4ohms

NL4 Speakon Connectors +

Loop Output

Screw terminal barrier strip

Subwoofer Model STX 6600 Made in Phillppines

10.000 255

TOP VIEW

INPUT PLATE

1.693 43

3.94 100

1.693 43

10.550 268

4.724 120

FRONT VIEW

1.693 43

SIDE VIEW

5.276 134

1.693 43

38.00 966

5.00 127

2.76 70

BACK VIEW SPECIFICATIONS

System Type

Coaxial, ribbon driver, line array, two-way, single sealed enclosure

Driver Components

(6) 6” ribbon drivers + (6) 6.5” paper/Kevlar composite mid-bass drivers

Crossover

Passive, custom

Frequency Response¹

70Hz - 20kHz @ -6db

Maximum SPL

128db continuous, 138db peak

System Coverage

110 degree horizontal, 20 degrees vertical (asymmetrical)

Sensitivity, 1m/2.83V

101db

Power Handling

720W AES, 1100W IEC long term, 1400W IEC short term

Recomended Amplifier Power @ 4ohms

500W-2000W (FTC) @ 4 ohms

Rated Impedance

6 ohms

Input Connectors

Screw terminal barrier strip and dual NL4 speakon connectors

Enclosure

Closed box alignment, 18mm marine plywood, heavily damped and braced

Mounting Options

(17) M10 fly points, (4) M8 points for wall mount option

Accessories (optional)

Wall Mounting Kit(BKT-WM66) for multiple stacked arrays L Bracket Kit(BKT-L66) for flying arrays under DRM215 subwoofer(s) Coupling Brackets(BKT-CP66) Allen Products MM-060 / MM-120 for single box wall mounting

Dimensions, (H x W x D) inches (mm)

Height 38.03” (966 mm) Width 10.550” (268 mm) Depth 10.04” (255 mm)

Weight, net

60.0 lbs. (27kgs)

Warranty

Limited 5-year warranty

ISOMETRIC VIEW

Warranty Ambisonic Systems LLC (Ambisonic) Warranty on Stix & Drums ‘Products’ is in effect for a period of 5 years from the date of first consumer purchase. Except as outlined below, your Stix & Drums Warranty covers all defects in material and workmanship as long as the product is properly used and maintained. If the Product is deemed defective by Ambisonic, Ambisonic will at its option, repair or replace the Product. If the defective Product cannot be repaired or is no longer available for replacement, Ambisonic may replace the Product with a current equivalent model of equal or greater value. Under terms of this Warranty, the Product must be returned to an authorized Stix & Drums dealer or Ambisonic. Return shipping and associated costs for exchanges or repairs is the sole responsibility of the original purchaser. Limitations: This limited Warranty does not cover failure of the Product resulting from improper installation, misuse, abuse, accident, neglect, mishandling, or wear and tear from ordinary use or environmental deterioration. This limited Warranty does not cover cosmetic damage, including paint damage, or consequential damage to the other components or premises which may result for any reason from the failure of the Product. This limited Warranty is null and void for Products not used in accordance with Ambisonic’s instructions. This limited Warranty is null and void for Products with altered or missing serial numbers and for Products not purchased from an authorized Stix & Drums dealer. This limited Warranty terminates if you sell or otherwise transfer this Product to another party.

Stix and Drums LLC 1990 N. McCulloch Blvd. Ste. D222 Lake Havasu City, AZ Voice: 928.733.6002 Fax: 928.453.5550 info@stixanddrums.com www.stixanddrums.com