Manual de serviço mini system sony hcd ne3 by Portal da Eletrônica

HCD-NE3 SERVICE MANUAL

US Model Canadian Model AEP Model UK Model E Model Australian Model

Ver. 1.1 2005.07

• HCD-NE3 is the amplifier, CD player, tape deck and tuner section in CMT-NE3.

CD Section

TAPE Section

Model Name Using Similar Mechanism

NEW

Base Unit Name

BU-K7BD80B

Optical Pick-up Name

KSM-213EDP/C2NP

Model Name Using Similar Mechanism

NEW

Tape Transport Mechanism Type

CMAL5Z220A

SPECIFICATIONS AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION: (US model)

With 6 ohm loads, both channels driven, from 120-10,000 Hz; rated 13 watts per channel minimum RMS power, with no more than 10% total harmonic distortion from 250 milliwatts to rated output.

Inputs MD (phono jacks): Outputs PHONES:

SPEAKER:

Sensitivity 450 mV, impedance 47 kilohms Accepts headphones with an impedance of 8 ohms or more Accepts impedance of 6 to 16 ohms.

CD player section Main unit

Laser

Amplifier section North American model: Continuous RMS power output (reference): 15 + 15 W (6 ohms at 1 kHz, 10% THD) European model: DIN power output (rated): 11 + 11 W (6 ohms at 1 kHz, DIN) Continuous RMS power output (reference): 15 + 15W (6 ohms at 1 kHz, 10% THD) Music power output (reference): 25 + 25 W Other models: The following measured at AC 230 V or AC 120 V, 50/ 60 Hz DIN power output (rated): 11 + 11 W (6 ohms at 1 kHz, DIN) Continuous RMS power output (reference): 15 + 15 W (6 ohms at 1 kHz, 10% THD)

Frequency response Wavelength

Semiconductor laser (λ=780 nm) Emission duration: continuous 20 Hz – 20 kHz 780 – 790 nm

Tape deck section Recording system Frequency response

4-track 2-channel, stereo 50 – 13,000 Hz (±3 dB), using Sony TYPE I cassettes

Tuner section

General

FM stereo, FM/AM superheterodyne tuner

Power requirements US, Canadian and Mexican models: 120 V AC, 60 Hz AEP and UK models: 230 V AC, 50/60 Hz Australian model: 230 – 240 V AC, 50/60 Hz Argentina and Korean models: 220 V AC, 60 Hz Taiwanese model: 120 V AC, 50/60 Hz Saudi Arabian model: 120 – 127/220 V AC, 50/ 60 Hz Other models: 110 – 120 V or 220 – 240 V AC, 50/60 Hz Adjustable with voltage selector

FM tuner section Tuning range Antenna Antenna terminals Intermediate frequency

87.5 – 108.0 MHz FM lead antenna 75 ohms unbalanced 10.7 MHz

AM tuner section US, Canadian, Mexican and Argentina models: 530 – 1,710 kHz (with the tuning interval set at 10 kHz) 531 – 1,710 kHz (with the tuning interval set at 9 kHz) AEP and UK models: 531 – 1,602 kHz (with the tuning interval set at 9 kHz) Other models: 530 – 1,710 kHz (with the tuning interval set at 10 kHz) 531 – 1,602 kHz (with the tuning interval set at 9 kHz) Antenna AM loop antenna, external antenna terminal Intermediate frequency 450 kHz

Power consumption

45 W

Dimensions (w/h/d)

Approx. 164 × 230.5 × 263 mm incl. projecting parts and controls

Mass

Approx. 3.7 kg

Supplied accessories

Remote Commander (1) R6 (size AA) batteries (2) AM loop antenna (1) FM lead antenna (1)

Design and specifications are subject to change without notice.

COMPACT DISC DECK RECEIVER 9-877-693-02

Sony Corporation

Personal Audio Group Published by Sony Engineering Corporation

HCD-NE3

Notes on chip component replacement • Never reuse a disconnected chip component. • Notice that the minus side of a tantalum capacitor may be damaged by heat. Flexible Circuit Board Repairing • Keep the temperature of the soldering iron around 270 ˚C during repairing. • Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). • Be careful not to apply force on the conductor when soldering or unsoldering. CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

The following caution label is located inside the unit.

CLASS 1 LASER PRODUCT LUOKAN 1 LASER LAITE KLASS 1 LASER APPARAT

This appliance is classified as a CLASS 1 LASER product.

SAFETY CHECK-OUT After correcting the original service problem, perform the following safety check before releasing the set to the customer: Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. LEAKAGE TEST The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes.). Leakage current can be measured by any one of three methods. 1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers’ instructions to use these instruments. 2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The “limit” indication is 0.75 V, so analog meters must have an accurate lowvoltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2 V AC range are suitable. (See Fig. A)

This label is located on the rear exterior.

UNLEADED SOLDER Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size)

To Exposed Metal Parts on Set

0.15 µF

1.5 k Ω

AC voltmeter (0.75 V)

Earth Ground

: LEAD FREE MARK Unleaded solder has the following characteristics. • Unleaded solder melts at a temperature about 40 ˚C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350 ˚C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! • Strong viscosity Unleaded solder is more viscou-s (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. • Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder.

Fig. A. Using an AC voltmeter to check AC leakage.

SAFETY-RELATED COMPONENT WARNING!!

ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.

HCD-NE3

TABLE OF CONTENTS 1.

SERVICING NOTES ................................................ 4

GENERAL Location of Controls ....................................................... 6

DISASSEMBLY

3-1. 3-2. 3-3. 3-4. 3-5. 3-6. 3-7. 3-8.

Disassembly Flow ........................................................... Rear Cabinet .................................................................... Top Panel Assy ................................................................ Front Panel Assy ............................................................. Base Unit (BU-K7BD80B) ............................................. Mechanical Deck ............................................................. MAIN Board ................................................................... AMP Board .....................................................................

TEST MODE .............................................................. 12

ELECTRICAL CHECK .......................................... 14

DIAGRAMS

6-1. Block Diagram – CD SERVO Section – ....................... 6-2. Block Diagram – MAIN Section – ................................ 6-3. Note for Printed Wiring Boards and Schematic Diagrams ................................................ 6-4. Printed Wiring Board – BD Board – ............................. 6-5. Schematic Diagram – BD Board – ................................ 6-6. Printed Wiring Boards – MAIN Section – .................... 6-7. Schematic Diagram – MAIN Section – ......................... 6-8. Printed Wiring Boards – AMP Section – ....................... 6-9. Schematic Diagram – AMP Section – ........................... 6-10. Printed Wiring Boards – PANEL Section – .................. 6-11. Schematic Diagram – PANEL Section – ....................... 6-12. Printed Wiring Board – POWER Board – ..................... 6-13. Schematic Diagram – POWER Board – ........................

8 8 9 9 10 10 11 11

15 16 17 18 19 20 21 22 23 24 25 26 27

EXPLODED VIEWS

7-1. 7-2. 7-3. 7-4.

Panel Section ................................................................... Front Panel Assy-1 .......................................................... Front Panel Assy-2 .......................................................... Top Panel Assy ................................................................

ELECTRICAL PARTS LIST ............................... 36

32 33 34 35

HCD-NE3 SECTION 1 SERVICING NOTES NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT

• MODEL IDENTIFICATION – Rear Cabinet –

The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. NOTES ON LASER DIODE EMISSION CHECK The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pick-up block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens. Power Voltage Indication

MODEL

Power Voltage Incdication

US, Canadian, Mexican and models

AC: 120 V 60 Hz 45 W

AEP and UK models

AC: 230 V - 50/60 Hz 45 W

Australian model

AC: 230 – 240 - 50/60 Hz 45 W

Argentina and Korean models

AC: 220 V - 60 Hz 45 W

Taiwan model

AC: 120 V 50/60 Hz 45 W

Saudi Arabia model

AC: 120 – 127/220 V 50/60 Hz 45 W

Other models

AC: 110 – 120/220 – 240 V 50/60 Hz 45 W

NOTE ON LEADING THE WIRE (FLAT TYPE) • In order to separate wire (flat type) from no shield portion of TC wire, stick filament tapes, as shown in a figure. TC wire (no shield portion)

main board

filament tape wire (flat type)

HCD-NE3

SERVICE POSITION – BD board –

BD board

– TCM block –

TCM block

– AMP board –

AMP board

HCD-NE3 SECTION 2 GENERAL • LOCATION OF CONTROLS

Main unit BUTTON DESCRIPTIONS

ALPHABETICAL ORDER

?/1 (power) 1 .m/M> (skip back/ skip forward,rewind/fast forward) 4 x (stop) 3 z RECPAUSE/START qh CD/NX(play/pause) ql TAPE/N(play) w; Z PUSHOPEN/CLOSE (CD open/close) 6 Z PUSHOPEN (tape open/close) qd

P–Z

A–O

PHONES jack qk PLAY MODE qj Remote sensor 2 TUNER/BAND qs TUNING +/− 4 TUNING MODE qj VOLUME qa

BASS/TREBLE 8 Cassette compartment qf CD SYNCHRO qg DISPLAY 0 Displaywindow 5 DSGX 9

1 2 34 5

8 9 0 qa qs

w; ql qk qj

qd qf

qh qg

This section is extracted from instruction manual.

HCD-NE3

Setting the clock

Remote control BUTTON DESCRIPTIONS

ALPHABETICAL ORDER A–O

?/1 (power) 1 m/M (rewind/fast forward) 7 ./> (go back/go forward) qf x (stop) 8 X (pause) 8 N (play) 8 +/− (tuning) qf

P– Z

CD qh CLEAR qd CLOCK/TIMER SELECT 2 CLOCK/TIMERS ET 3 DISPLAY ql ENTER 9 EQ qs FM MODE 4 FUNCTION 6

PLAY MODE qk REPEAT 4 SLEEP w; TAPE qg TUNER/BAND 5 TUNER MEMORY qj TUNING MODE qk VOLUME +/− 0

Use buttons on the remote for the operation.

1 2 3 4 5 6

Press ?/1 to turn on the system. Press CLOCK/TIMER SET. Press ./> repeatedly to set the hour. Press ENTER. Press ./> repeatedly to set the minute. Press ENTER.

The clock starts working.

To adjust the clock

1 Press CLOCK/TIMER SET. 2 Press ./> until “CLOCK” appears, then press ENTER.

3 Do the same procedures as step 3 to 6

CMT-NE3

above. Note

ql qk qj qh qg qf

The clock is not displayed in Power Saving Mode.

2 3 4 5 6 7 8

qd qs

* 0

* Button does not function with this model.

HCD-NE3 SECTION 3 DISASSEMBLY • This set can be disassembled in the order shown below.

3-1.

DISASSEMBLY FLOW SET

3-2. REAR CABINET (Page 8)

3-3. TOP PANEL ASSY (Page 9)

3-4. FRONT PANEL ASSY (Page 9)

3-5. BASE UNIT (BU-K7BD80B) (Page 10)

3-6. MECHANICAL DECK (Page 10)

3-7. MAIN BOARD (Page 11)

3-8. AMP BOARD (Page 11)

Note: Follow the disassembly procedure in the numerical order given.

3-2.

REAR CABINET

1 four screws (BVTP3 × 8)

4 five screws (BVTP3 × 10) 3 two screws (BVTP3 × 10)

7 rear cabinet

6 two screws (BVTP3 × 10)

5 two screws (BVTP3 × 10)

2 four screws (BVTP3 × 8)

HCD-NE3

3-3.

TOP PANEL ASSY 6 top panel assy

5 connector (S820)

4 wire (flat type) (17 core) (CN305)

2 claw

1 claw

3-4.

FRONT PANEL ASSY 2 wire (flat type) (8 core) (CN303) q; wire (flat type) (11 core) 3 connector (CN309) 5 connector (CN301) 4 connector (CN501)

1 wire (flat type) (19 core) (CN302) qa screw (2.6 × 10) qs harness

9 8

7 qd flont panel assy

6 two screws (BVTP3 × 10)

HCD-NE3

3-5.

BASE UNIT (BU-K7BD80B)

6 base unit (BU-K7BD80B)

4 two screws (2.6 × 10) 5 two screws (2.6 × 10)

3 wire (flat type) (17core) (CN201)

2 CD cover

1 three screws (BVTP2.6 × 8)

3-6.

MECHANICAL DECK 2 screw (BVTT2.6 × 6)

1 three screws (2.6 × 10)

3 shield (TC)

4 mechanical deck

HCD-NE3

3-7.

MAIN BOARD

5 main board

1 connector (CNB308)

3 connector (CNB307)

4 two screws (BVTP3 × 10)

6 tuner (FM/AM)

2 connector (CN902)

3-8.

AMP BOARD

4 AMP board

3 two screws (BVTP3 × 10)

1 connector (CNB308) 2 connector (CNB307)

HCD-NE3 SECTION 4 TEST MODE COLD RESET *

The cold reset clears all data including preset data stored in the RAM to initial conditions. Execute this mode when returning the set to the customer. Procedure: 1. Press the I/1 button to turn the power on. 2. While pressing the x button, press the I/1 button and turn the [VOLUME] knob in the counter-clock wise. 3. The message “RESET” is displayed and the set is reset.

PANEL TEST All segments of liquid crystal display are tested, and the version and released date of the micro computer are displayed. Procedure: 1. Press the I/1 button to turn the power on. 2. While pressing the [DISPLAY] button, press the I/1 button and turn the [VOLUME] knob in the counter-clock wise. Then all segments of liquid crystal display are turned on. 3. Press the [DSGX] button, the version and released date of the micro computer are displayed. example of display:

The third and 4th digit from the left indicates: (Error status display) The third and 4th digit from the left indicates which error status is indicated. Display

Not focused (TOC read without a disc)

0 2

GFS NG (TOC read with a disc chucked)

0 3

Start operation time-over

0 4

Defocused continuously (Defocused during TOC reading)

0 5

Q code not entered for specified time

0 6

Tracking not turned ON

0 7

Blank disc (Blank disc TOC read)

1209 V100

Status

0 1

The 5th and 6th digit from the left indicates: (Error step display) The 5th and 6th digit from the left indicates which processing when a trouble occurred Display

Contents

0 1

SHIP in progress

0 2

Power OFF in progress

released date of micro computer (In this case, released of December 9)

0 3

Power ON in progress

0 4

Initialize in progress

4. Press the [BASS/TREBLE] button, the model name and destination are displayed. example of display:

0 5

Oscillation stopping

0 6

From oscillation stop, oscillation starting

0 7

Stopping

0 8

Stop operation is under way

Version of micro computer (In this case, version 100)

N3 NA

0 9

Start operation in progress

destination (In this case, North-American model)

0 A

TOC read in progress

0 B

Search operation is under way

model name (In this case, HCD-NE3)

0 C

Playback operation is under way

0 D

Pause operation is under way

0 E

Playback manual search operation is under way

0 F

Pause manual search operation is under way

To exit from this mode, perform the “COLD RESET”.

CD ERROR CODE DISPLAY MODE • When this mode is entered, optical pick-up error code is displayed with the 8-character format on the liquid crystal display. Procedure: 1. Press the I/1 button to turn the power ON. 2. Press the CD N X button to select “CD”. 3. While pressing the [DISPLAY] button, press the [PLAY/MODE/ TUNING MODE] and turn the [VOLUME] knob in the counterclockwise. 4. When this mode is activated, CD error code is displayed on the liquid crystal display. 5. Press the TUNING + M > and TUNING – . m buttons, error history No. is changed. The first digit from the left indicates: The first digit from the left indicates which mode the error history is. “D” is displayed on the liquid crystal display. The second digit from the left indicates: (Error history No. display) The second digit from the left indicates which order the error history is. “0” indicates the latest error history, and each time the number increases by one, the error history goes back to one-previous error.

The 7th and 8th digit from the left indicates: The 7th and 8th digit from the left indicates which operation in progress when a trouble occurred. (Step of each processing of the 5th and 6th digits is indicated)

5 REPEAT LIMIT CANCEL MODE • Number of repeat for CD playback is 5 times when the repeat mode is “REPEAT”. This mode is used to enables CD to repeat playback for limitless times. Procedure: 1. Press the I/1 button to turn the power ON. 2. Press the CD N X button to select “CD”. 3. While pressing the x button, press the [PLAY MODE/TUNING MODE] and turn the [VOLUME] knob in the counterclockwise. 4. The message “NO LIMIT” is displayed on the liquid crystal display momentarily, CD repeat 5 limit is cancelled.

HCD-NE3

TUNER STEP CHANGE-OVER *

Either the 9 kHz step or 10 kHz step can be selected for the AM channel step. Procedure: 1. Set the FUNCTION to AM, and press the I/1 button to turn the power off. 2. While depressing the TUNING + M > button, press the I/1 button. 3. The message “9K STEP” or “10K STEP” is displayed on the liquid crystal display, and thus the channel step is changed over.

HCD-NE3 SECTION 5 ELECTRICAL CHECK Note: 1. CD Block is basically constructed to operate without adjustment. 2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated. 3. Use an oscilloscope with more than 10 MΩ impedance. 4. Clean the object lens by an applicator with neutral detergent when the signal level is low than specified value with the following checks. 5. Check the focus bias check when optical block is replaced. FOCUS BIAS CHECK oscilloscope (DC range) BD board TP012 (RFACO) TP013 (VC)

+ –

Procedure : 1. Connect the oscilloscope to TP012 (RFACO) and TP013 (VC) on the BD board. 2. Insert the disc (YEDS-18). (Part No. : 3-702-101-01) 3. Press the CD N X button. 4. Confirm that the oscilloscope waveform is as shown in the figure below. (eye pattern) A good eye pattern means that the diamond shape (◊) in the center of the waveform can be clearly distinguished. • RF signal reference waveform (eye pattern) VOLT/DIV: 0.2 V (with the 10: 1 probe in use.) TIME/DIV: 500 ns

1.1

0.2 Vp-p

When observing the eye pattern, set the oscilloscope for AC range and raise vertical sensitivity.

Checking Location: – BD BOARD (Conductor Side) –

TP012 (RFACO)

TP013 (VC)

HCD-NE3 SECTION 6 DIAGRAMS BLOCK DIAGRAM – CD SERVO Section – 110

CD DSP IC101 (1/2)

XTAO

B 26 C 27 D I-V AMP

RF SUMMING AMP

B C

EQ_ IN

RFAC VCA

RFACO

39 42

FOCUS ERROR AMP

AC_ SUM

FEO

RFACI

ASYMMETRY CORRECTOR

XTAI XTACN

EFM DEMODULATOR

DIGITAL PLL

ASYI ASYO

AOUT1 INTERNAL BUS

FILO PCO CLTV FILI

CLOCK GENERATOR

48 50 47 49 105

D +3.3V

XTSL

XPCK

DETECTOR

C4M

FILTER

32K RAM ERROR CORRECTOR

D/A CONVERTER

AOUT2

D/A DIGITAL INTERFACE

X171 16.9344MHz

73 88

CD 76 81

R-CH

SELECTOR TO SERVO AUTO SEQUENCER

DIGITAL CLV PROCESSOR

95 98 97 100 108 91 92 89 90

103 104 106 64

59 62 61

LRCKI BCKI PCMDI

WFCK XUGF GFS EMPH

OPTICAL PICK-UP BLOCK (KSM-213EDP)

CPU INTERFACE SBSO EXCK SQSO SQCK

SCOR

TEO

SENS

TRACKING ERROR AMP

MDP

DATA CLOK XLAT

19 E

SUBCODE PROCESSOR

XRST

LRCK BCK PCMD

6-1.

58 56 57

LASER DIODE PD

APC LD AMP

6 8 9

27 CD SCOR

CD SENS

CD DATA CD CLK CD XLT

AUTOMATIC POWER CONTROL Q10

CD XTXCN 3 MOTOR/COIL DRIVE IC251

M101 (SPINDLE)

16 15

CH4OUTF CH4OUTR

MOTOR DRIVE

CH4IN

OPOUT

OPIN+

CH3FIN

MOTOR CH3OUTR DRIVE 18

CH3RIN

SYSTEM CONTROLLER IC801 (1/2)

A/D CONVERTER

9 10

2-AXIS DEVICE (FOCUS) (TRACKING)

14 13

CH1OUTF CH1OUTR

CH1FIN COIL DRIVE

CH1RIN

12 13 14

12 11

CH2OUTF CH2OUTR

CH2FIN COIL DRIVE

CH2RIN

SFDR SRDR TFDR TRDR FFDR FRDR

FOCUS/ TRACKING/SLED SERVO DSP

MIRR, DFCT, FOK DETECTOR

FOK MIRR DFCT

COUT SERVO INTERFACE

SCLK

3 1 2

112 101

SERVO AUTO SEQUENCER

6 7

MUTE

• R-ch is omitted due to same as L-ch. • SIGNAL PATH

CD XRST

CH3OUTF

SSTP

FOCUS/TRACKING/SLED PWM GENERATOR

M102 (SLED)

TEI FEI

20 22 CD DSP IC101 (2/2)

TO CPU INTERFACE

: CD PLAY

7 S101 (LIMIT)

(Page 16)

HCD-NE3

6-2.

BLOCK DIAGRAM – MAIN Section – J303

19 AUX-L

MD R

(Page 15)

R-CH

OUT-L 18

POWER AMP IC501

21 CD-L

J301 PHONES

R-CH FM/AM TUNER PACK FM 75Ω COAXIAL

FM ANT

TU-LCH

23 TU-L

TU-DI AM ANT TU-DO TU-CL ANT GND TU-CE TUNED STEREO MUTE

: TUNER

R-CH

ANT GND TU-RCH ANTENNA

• R-ch is omitted due to same as L-ch. • SIGNAL PATH

DO DI CLK CE TUNED STEREO TU-MUTING

INPUT SELECT, ELECTRICAL VOLUME IC302

+ –

: CD PLAY

J302 SPEAKER IMPEDANCE USE 6 – 16Ω

: TAPE PLAY : REC : AUX IN

REC-O-L 28

2 TA-L

CONT 13

L-CH

R-CH HRPE301 (REC/PB/ERASE)

DC DETECT Q342, 343

REC BIAS SWITCH Q346 – 348

R-CH

B +10V

MAIN POWER TRANSFORMER T902

D307 D920, 921

ERASE REC/PB SWITCH Q326 – 332

BIAS OSC T301

BIAS OSC Q344, 345

AC DETECT Q333, 338

AMP B+

RECT D918, 919

AMP B–

RECT D916, 917

DO DI CLK CE TU-MUTING TUNED STEREO

TO POWER AMP

98 99

F DATA

XT2

XT1

CF2

CF1

AMP STBY

I POWER MONITOR

SYSTEM CONTROLLER IC801 (2/2)

LED DRIVE Q808

LED DRIVE Q806

+3.3V REGULATOR Q317 +7V REGULATOR IC306

M +7V

+3.3V REGULATOR Q339

D810

D806 (STANDBY)

VOLTAGE DETECT IC803

I POWER DOWN 23

LCD COM0 – 3

29 RMC

RESET 11 22 VOL ENCODER PWR ON 1

S801 – 813 (FRONT PANEL KEYS)

(E, E51, EA, SP) SUB POWER TRANSFORMER T901

SYS +3.1V SYS +3.2V

ROTARY ENCODER RV801

RECT D913, 914

D809

S820 (CD LID OPEN/CLOSE DETECT)

VOLUME

(EXCEPT E, E51, EA, SP)

+10V REGULATOR IC305

VM +10V

4 CD OPEN D701 – 703 (LCD BACK LIGHT)

B+ SWITCH Q319, 320

CD ON 2

SEG1 – 33

FL801 FLUORESCENT INDICATOR TUBE

REMOTE CONTROL RECEIVER IC802

D +3.3V

SYS +3.3V

25, 26

79 – 56, 53 – 45

24 TA-SW 91 TA PLAY SW 92 TA END SW

AMP MUTE

96 TA SOL

PACK REC PLAY SW FWD SW

ST/BY

(DECK-A)

PLUNGER DRIVE Q802, 803

94 95

TA REC/PLAY TA BIAS

SOL 9V

93 TA MOTOR

32 30 34 35 33 36 37

BACK LIGHT ON

(CAPSTAN/REEL)

CAPSTAN/REEL MOTOR DRIVE Q804, 805

83 – 86

MOTOR 9V

X802 10MHz

TU DO TU DI TU CLK TU CE TU MUTE TU TUNED TU STEREO

TAPE MECHANISM DECK BLOCK

X801 32.768kHz

KEY0, KEY1

+3.9V REGULATOR Q312 – 314

RECT D907 – 910 D922

D923, 924

RY901 VOLTAGE SELECTOR S901 (AC IN)

(EXCEPT E, E51, EA, SP)

RESET SWITCH Q801 MAIN POWER RELAY DRIVE Q311, 315

HCD-NE3

6-3.

• Circuit Boards Location

NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

Note on Printed Wiring Board: • X : parts extracted from the component side. • Y : parts extracted from the conductor side. f • : internal component. : Pattern from the side which enables seeing. • (The other layers' patterns are not indicated.) Caution: Pattern face side: (Conductor Side) Parts face side: (Component Side)

Parts on the pattern face side seen from the pattern face are indicated. Parts on the parts face side seen from the parts face are indicated.

• Indication of transistor.

C Q

These are omitted.

B E

Q B

E These are omitted.

Q B

E These are omitted.

Note on Schematic Diagram: • All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums. • All resistors are in Ω and 1/4 W or less unless otherwise specified. f • : internal component. • 2 : nonflammable resistor. • 5 : fusible resistor. • C : panel designation. Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.

MAIN board

BD board AMP board

CONTROL board

Note: Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce por tant le numéro spécifié.

• A : B+ Line. • B : B– Line. • Voltages and waveforms are dc with respect to ground under no-signal conditions. – CD Board – no mark : CD PLAY – Other Sections – no mark : TUNER ( ) : CD PLAY 〈〈 〉〉 : TAPE PLAY { } : REC • Voltages are taken with a VOM (Input impedance 10 MΩ). Voltage variations may be noted due to normal production tolerances. • Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances. • Circled numbers refer to waveforms. • Signal path. F : TUNER J : CD PLAY E : TAPE PLAY j : REC f : AUX IN • Abbreviation AR : Argentina model AUS : Australian model CND : Canadian model E51 : Chiliean and Peruvian models EA : Saudi Arabia model KR : Korean model MX : Mexican model SP : Singapore model TW : Taiwan model

HP board

BACK LIGHT board POWER board TUNER unit

HCD-NE3 • See page 17 for Circuit Boards Location.

PRINTED WIRING BOARD – BD Board –

:Uses unleaded solder.

BD BOARD

R121

C131

JW114

C132

C111 R113

TP013 (VC)

JW111 JW110

JR106 JW108

CN101

JW120

JW117

IC101 56

JW119

JW123

C161

M101 (SPINDLE)

C15

112

C160

JW107

R151

JW109

JW116

C141

R143

R141

C195

C143

OPTICAL PICK-UP BLOCK (KSM-213EDP)

JW112

C114 JR107

C204 R142

R202

JR111

C115

C142

C11

C113 R114

C124

Q10

C112

C133 R132

C10

R10

JR105

R111 R112

C125

TP012 (RFACO)

R133

C17 R11

R131

JR108

JW115

C122

C117

R13

C14

JR109

C16

R12

JW113

C116

C123

C18

JW118

R251 JW106

C162 C251

R161

C171

JW105

R171 C164

X101 C183

C172

R181

R173

C194

C184

C182

JR104

R182

R252

C212

C259

JW125

C186 JW126 JR110

C201

R162

R407

C202

JW134 JR101 R410

JW103

R406

C252

R408 C170 M102 (SLED)

C213

CN201

MAIN BOARD CN305

(Page 20)

R411

JW101

C203

JW127

R412

C258

C257

R204 R201

JW133

C163

S101 (LIMIT)

IC251

JW132

C211

C210

JR102

JW131 R409 JW128

JW104 1

JR103

C181

C151

C174

C185

R172

JW124

6-4.

1-861-620-

JW102

(12)

HCD-NE3 • See page 28 for IC Block Diagrams.

SCHEMATIC DIAGRAM – BD Board –

• See page 28 for Waveforms.

CN201 17P XTACN C201 220 10V

JR110 0

C174 0.1

C161 0.1

C151 220 10V

C171

MGND(7V)

22p

X101 16.9344MHz R172 1M R171 470

M+7V

JR103 0

PCMDI

LRCKI

VSS

LRCK

BCK

PCMD

VDD

EMPH

EMPHI

IOVDD2

XTAI

XTAO

XVDD

VREFL

AOUT1

AVDD1

AVSS1

AVSS2

0.1 C163

C212 22p

VREFR

100 R406

C211 220p

AOUT2

100 R407

IOVDD0

100

LMUT

JR104 0

100

C210 0.1

AVDD2

C143 0.1 RMUT 100

R151 0

BCKI

XTSL

DDCR

IOVSS0

AVSS5

R202 0

XTACN

DDVRSEN

SQSO

DDVROUT

SQCK

AVDD5

SBSO

PCO

EXCK

FILI

XRST

FILO

SYSM

CLTV

DATA

AVSS3

VSS

VCTL

XLAT

VPCO

CLOK

ASYO

R141 4.7k

R142 1k

C141 0.1 R143 3.3k

C125 0.1 C142 1500p C117 0.1

R132 10k

R133 180k

C133 0.01

TP46 IOP1 C132

VDD

CD DSP

ASYI

SENS

IC101 CXD3058AR

BIAS R131

SCLK

AVDD3

ATSK

RFACI

C131

TP012 WFCK

RFACO

XUGF

AVSS4

XPCK

RFC PD

GFS

C2PO

0.47

C17 220 10V

R13 1 TP45 IOP2

100p

C124 330p

RFACO

R121

15k

C123

0.1

R12 100k

EQ_IN

SCOR

C164 0.1

VDD

AC_SUM

C4M

PDSENS

C122 0.1

R11 0

AUTOMATIC POWER CONTROL

FEI

AVDD4 F

FFDR

TRDR

TFDR

SRDR

SFDR

IOVSS1

SSTP

MDP

LOCK

VSS

MIRR

FOK

DFCT

COUT

Q10 2SB1690K C18 1000p

JR109 0

RFDCO

WDCK

R10 3.3

C16 1

JPO001

JR102 0

JR105 0

CN101 16P

C15 0.1

TP27

JR111 0

FFDR

TRDR

TFDR

SRDR

SFDR

C195 0.1

C11 10 TP016 C251 6800p

0.1

R252 22k

C14 0.1 JPO003

T-

T+

F+

FRDR

FFDR

TRDR

TFDR

F-

C258 0.1

C114 470p JR107 0

R113 1k

R111 1k

R114 15k

R112 15k C113 3300p

C111 3300p

C10 10

C116 220 10V

VCC E

TP014

TP17

TP18

TP19

TP20

TP015 JR106 0

R251 10k

TOP1

C115 0.1

JPO002

C259

SSTP

TP013

C160 0.1

D A B JR108 F

C F AGND

TP28

TP21

AGND

TP22

F+

TP23

F+

T+

TP24

T+

T-

TP25

T-

F-

TP26

F-

C112 470p

MOTOR/COIL DRIVE

IC251 BA5947FM S101 (LIMIT)

C252 0.1

M101

JPO004

SRDR

(SPINDLE) SFDR

TP43 TP44

R408

M+7V

R173 0

C183 220 10V

TEI

SCOR

C185 470p

C184 220 10V

C172

SENS

TP42

C186 470p

C194 0.1

R182

TP41

SCOR MGND(7V)

R162 47k

CLK

SENS

R409

TP40

R412 100

XLT

100

CLK

TP39

TEST

DATA

XLT

R410

(Page 21)

DOUT

XRST

TP38

TP37

DATA

XRST

C162 0.1

R204

TES1

DVDD

AVSS0

TP36

C203 220 10V

C202 0.1

22p

DVDD

C213

XVSS

DGND

IOVSS2

ROUT

TP35

AVDD0

TP34

DGND

AVDD

IOVDD1

ROUT

TP32

R201

FRDR

AGND

FRDR

LOUT

TP30

C181 0.1

100

TP33

AGND

AVDD

C182 0.1

100

R181

LOUT

R161

27p

DOUT

100

TP31

DOUT

FEO

TP29

AGND

TEO

XTACN

R411

6-5.

M102

C170 220 16V

(SLED)

C257 0.1

JR101 0

The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.

Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.

HCD-NE3

AMP BOARD CN502

:Uses unleaded solder.

R320 R303

R301

C207

C204

C104

C107

D302

C331

JW313

C329

JW347 C101

C209

JW349

C109 JW344

R100

R114

R113

C211

C354

R218

R319

C312 C102

R102

C202

C206

R107 R202

R217

R117

R219

R119

C330

D303

B Q348

(Page 24)

C328

C355

C362

R368

C356

JW363

JW322 8

JW366

R362

R332

C323

Q344

JW365

JW384

Q339

JW382

JW369

JW370

R360

Q345

JW371

D304

JW381

C358

CONTROL BOARD CNB302

R367

JW364

JW362

JW319

C357 JW367

C335

JW351

JW361

CNB301

R366 R353

JW360 CNB307

Q347

JW358

T301 3 2

C361

JW357

JW323

C346

C353

R115

R365

C320

C219

R364

JW377

L201

R-CH

R201

C360

CN302

R318

JW380

E Q319

–

JW350

C201

JW352

JW341

JW353 JW378

JW318

JW356

JW379

JW316

C121

R208

L-CH

Q326

C314

Q346

JW354

Q320 R317

JW311

R348

JW315

HRPE301 (REC/PB/ERASE) 1

JW359

Q317

C309

JW310

C112

C212 R226

JW355 C221

Q342

JW321

C333

Q343

–

J302 SPEAKER IMPEDANCE USE 8 – 16Ω

R214 R215

C217

C351

C332 C352

C236

C115

C119

C216 C117

JW340

JW338

JW314 L101

R111

R358 C136

D CN301 D

C111

R359 JW339

JW309 +

C110

R213

C116 R225

Q332

Q331

Q328

R112

R212

R118

R216

R125

C215

D305

D306 R220

R116

R132 C135

JW343

JW320

R228

R124

R221

R126

D321

R109

R211 R120 R121

Q327

R209

C210

JW337

D322

R143

JW335

HP BOARD CNB501

(Page 22)

C114

Q330

JW345 E JW346 JW348

R122

JW333

R371

R231

C118

R370

R131 C218

R372

R128

CNB308

R203

JW336

R243 C133

C113

C213

JW334

C106 R103

R222

C233

FB302

R232

JW332

C103

Q329

R108

C235 C234

JW331

R136

JW329

C126

C203

IC302

R123 JW327

R137 R

R105

R223

JW328

J303 MD

C132

R106

JW324

JW325

FB317

C127

C208

R304

C232

C322

JW326

C227

R224

C308

C370

C214

CN305

JW304

(CHASSIS)

JW301

C305

R236

JW342

C226

R206 R205

C108

C302

R207

CN303

R101

R302

R200

R204

D318

R305

R104

C313 C315

C310

JW308

C301

C316

R237

R363

C345

POWER BOARD CN902

JW368

R361

(Page 26)

D317

C336

(11)

IC306

Q333

Q313

Q312

R321 Q315

JW372

R322

JW373

R325

R315 D310

D308 Q311

D301

Q338 E

R336 R350

11 1-861-724-

R351

Q314

D307

JW375

R327 3

JW376

IC305 REG BOARD

R324

C350

R326

R323

C306

C307 1

CN306

C326

1-861-729-

CN307

R349

C324

(Page 24)

FB301

CONTROL BOARD CNB303

R352

C318

JW383

C319

JW307

MAIN BOARD

(Page 22)

C134

M-11 L-10 L-10 L-9 K-13 F-8 G-7 F-7 C-14 C-13 B-14 B-13 B-13 B-14 B-15 K-12 K-14 I-9 F-10 E-9 H-13 I-13 E-12 G-12 G-12

BD BOARD CN201

(Page 18)

R373

Q311 Q312 Q313 Q314 Q315 Q317 Q319 Q320 Q326 Q327 Q328 Q329 Q330 Q331 Q332 Q333 Q338 Q339 Q342 Q343 Q344 Q345 Q346 Q347 Q348

C-12 K-6 K-7

JW302

IC302 IC305 IC306

A A

C321

K-14 B-13 G-8 I-9 C-11 C-10 K-13 M-10 L-10 K-12 B-10 E-5 D-5

JW312

D301 D302 D303 D304 D305 D306 D307 D308 D310 D317 D318 D321 D322

CN309

Location

JW120

Ref. No.

C311

• Semiconductor Location

PRINTED WIRING BOARDS – MAIN Section – • See page 17 for Circuit Boards Location.

C317

6-6.

(11)

ERASE

HCD-NE3 • See page 28 for IC Block Diagram.

SCHEMATIC DIAGRAM – MAIN Section –

• See page 28 for Waveforms.

J302 4P R225

22k

C232

4.7

50V

R125

22k

C132

4.7

50V

C119 0.01

L SPEAKER

10k

IMPEDANCE

470p

220p

J303 2P

4.7k

R136

C127

C126

R137

FB317

USE 8-16

C117

0.0012

R126

22k

C136

50V

TU LCH

C217

0.0012

R226

22k

C236

50V

TU RCH

C219 0.01

C121 0.1

LP221

C211 0.0033

C116 470p

(CHASSIS)

R221

C213 0.22 50V

15k

R108

CN301 7P

R208

HRPE301

10k

SP OUT(R) GND L101

C214 0.47 50V R222 68k

SP OUT(L)

(Page 23)

CN309 3P C115 4.7 50V

C133 0.047

CNB308 9P

C235 10 50V

R143 8.2k

R R124 15k

R209 2.2k

JW120 0.1

L201

R223 2.2k

C114 0.47 50V R122 68k

R121

C113 0.22 50V

R120

10k R220

R123 2.2k

2.2k

1.8k

6.8k R118

R119

R219

R117 R218

R116

6.8k

8.2k

8.2k R216

1.8k

2.2k

C221 0.1

R217

C370 0.1

(CHASSIS)

C212 0.0047

R214 560 R212 33k

R211 2.2k

R111 2.2k

C210 180p

R109 2.2k

C216 470p

R213 470

C111 0.0033 R113 470

R112 33k

R236 10k

(REC/PB/ERASE)

R114 560

470p

R115 3.3k

C110 180p

C109

R215 3.3k

C209

470p

470p C227

220p C226

4.7k

C112 0.0047

R MD

R237

AGND

C215 4.7 50V

L R132 1k R224 15k

AMP-MUTE

C135 10 50V

R232 1k

AMP-STBY

(Page 23)

PROTECT BASS-R

OUT-R

BASS-L

OUT-L

AUX-L

AUX-R

CD-L

TU-L

CD-R

TU-R

RECO-R

NF-R

RECO-L

NF-L

-B L-CH

C233 0.047

INPUT SELECT,

R243 8.2k

GND +B R370 10k R371 10k

VEE

IC302 BD3881FV

1800p

39k R202

C202

39k R102

1800p

R105

390k

R106 5.6k R104 47 C104 100 10V

R107 150k

C352 2200 35V

C309 1000 16V

D318 1SS133T-77 R352 470

REG07-IN

C333 220 50V

+10V REGULATOR

R206 5.6k

C204 100 10V

C302 470 6.3V

R207 150k

D305 MTZJ-T-77 -4.3C

IC305 TA7810S O

R303 10k

R204 47

C306 0.1

REG07-GND

R302 15k

C208 0.0033

R301 47k

CN306 3P

CNB307 6P

REG07-OUT

R372 82k

C206 0.022

I G

C118 0.033

C218 0.033

R128 1.2k C134 0.0022

R131 1.2k

R359 1.5k C108 0.0033

C207

C106 0.022

C107 2.2 50V

R203 470

R228 1.2k

2.2

R205 390k

C103 100p

C203 100p

R103 470

IC306 BA07T +7V REGULATOR

R231 1.2k

50V

ERASE

C234 0.0022

VDD

CONT

VOLUME

TRE-R

GND

TRE-L

VOLI-R

PBO-L

VOLI-L

PB0-R

NF-R

TA-R

NF-L

R-CH

TA-L

ELECTRICAL

C102

C305 470 6.3V

C301 10p

C313 100 16V

I G

C323 2200 25V

C351 100 25V

D306 MTZJ-T-77 -4.3C

CN307 3P

R358 56k

C307 0.1

Q326-332 REC/PB SWITCH

Q330 2SK2158 -T2B

CN302 19P TU RCH

C101 68p

C201 68p

R101 12k

R201 12k

R100 180

R200 180

Q329 2SK2158 -T2B

R320 4.7k

Q332 KRA303 -RTK

DC DETECT

TU LCH

SUB +B

R373 10k

PROTECT RELAY ON AC-DET

TU-RCH TU GND

GND

14V

D302 1SS133T -77

C312 220p

TU 10V TU 10V

D308 1SS133T-77

M+7V M+7V

Q326 KTA1504

TA 10V

(Page 27)

CNB301 8P

TU-LCH

Q311,315

TA GND

Q311 KTA1271Y-AT

MAIN POWER

JW323 10UH

TA GND

MGND(7V)

Q314 KTA1271Y-AT

SCOR C310 0.1

RELAY DRIVE

TA BIAS

F DATA

C317

100p

SCOR SENS SENS

C311

AC DETECT

R323 1k

REGULATOR

C326 0.0022

C316

100p

C315

100p

XLT DATA XRST

+3.9V

AMP-STBY

CLK

100p DATA

R324 2.2k

Q312-314 R315 1k

Q333,338

100p XLT

R351 10k

P-CONT

100p

C319

D310 MTZJ-T-77 -4.3C

R321 100k

A-MUTE

C318

CLOK

R336 4.7k

REC/PB

XRST

R325 100k

DVDD C322 0.001

AMP-MUTE

DGND

Q338 KRC402-RTK

I POWER MONITOR AC-DET

ROUT

AC-DET

Q333 KRC402-RTK

3.3V(MAIN)

LOUT Q312 KTC3203Y

GND C336 22 50V

GND

(Page 19)

AGND

Q315 KRC402-RTK

C324 220 16V

R350 10k

Q313 KTC3203Y

C321 0.001

C346 2200 16V

R322 1.5k

AVDD FB301

DOUT

3.9V(SUB)

AGND XTACN

D301 1SS133T-77

XTACN C329 1000 6.3V

Q346 2SD1387-34 -TP

Q347 KTA1266-GR -AT

R349 56k

R327 10k

CN305 17P

C308 0.1

CN303 8P

R326 100k

SCOR SCOR

BIAS OSC

1k XLT

DATA XRST XRST XTACN

0.01

470

16V

D304 MTZJ-T-77 -3.9B

XTACN CD ON

TU 10V

TA 10V

REG07-GND

Q345 2SC2001TP-LK

FB302

The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.

(Page 25)

CD ON

C335 0.01

TA GND

R361 5.6

C345 10 50V

CD ON

R360 5.6

M+7V

C362 10 50V

100

R304

DATA

R332 1k

REG07-IN

C361 47 16V

R305

XLT

CLOK

REGULATOR

B+ SWITCH

REG07-OUT

C360 10 50V

Q319,320

Q320 KRC402 -RTK

CLOK

+3.3V

C328

Q344,345

R348 1k

10V

R363 18k

Q348 KRC102M-AT R364 6.8k

R318 470

2200

R365 2.2k

SENS Q339 KTC3203Y R353 10

0.01

Q344 2SC2001TP -LK

R317 47k

REGULATOR

C332

R367 2.2k

C357 0.0068

C331

R362 18k

C354 2.2 50V

Q319 KTA1273Y -AT

+3.3V

BIAS OSC

C314 0.01

SENS

Q317 KTC3205Y

C358 0.018

R368 10k

C330 100 10V

R366 22k

SWITCH

C320

C356 0.0068

Q346-348 REC BIAS T301

D303 MTZJ-T-77-3.9B

(Page 25)

AC-DET

Q327 KTA1504

Q328 2SK2158-T2B

D317 1SS133T-77

TA 10V

-B

D321 1SS133T -77

D307 1SS133T -77

Q342,343

R319 1M

D322 1SS133T -77

Q342 2SC1623-T1 -L5L6

Q331 KRA303 -RTK

C353 2200 35V

Q343 2SC1623-T1 -L5L6

C355 0.015

6-7.

Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.

HCD-NE3

PRINTED WIRING BOARDS – AMP Section – • See page 17 for Circuit Boards Location. MAIN BOARD CNB308 (Page 20)

D AMP BOARD

HP BOARD

R518 9

MAIN BOARD CN309 (Page 20)

CNB501

1 CN502

CN501

J301 PHONES

C520

R517

:Uses unleaded solder.

C521

6-8.

C512

R520

R519

R515

R516 C511

1-861-728-

C514

JW508

JW509

C513 C510

JW510

C509

EP903 JW513 C507

R511

R507

R506

R502

R505

JW502

JW511

JW506 JW512

IC501

JW501

C501

C506

R508

C505

R504

R509

R512

C516

JW503

JW507

(CHASSIS)

R514

JW505 JW504

R503

C503

R501

11 1-861-726-

(11)

11 (11)

HCD-NE3

6-9.

SCHEMATIC DIAGRAM – AMP Section –

CN502 9P +B GND -B PROTECT R514

10k

R507

10k

AMP-STBY R512 33k

AMP-MUTE

(Page 21)

L AGND C506 47 25V

R R501 1k

R502 47k

R505 47k

C503 47 25V

R506 1k

C516 100 16V

R508 680

R515 2.2

R516 2.2

C512 1

C514 1

C511 1

C513 1

R517 56k

R519 330

CN501 4P SP OUT(R) HP OUT(R) HP OUT(L)

R518 47k

SP OUT(L)

C507 0.1 R511 33k

R520 330

R503 680 C509 220 35V

C510 220 35V EP903

(CHASSIS GND) C505 100p C501 100p

R509 47k

R504 47k

J301 PHONES

CNB501 7P SP OUT(R) HP OUT(R) HP OUT(L) SP OUT(L) SP OUT(R)

C520 10000p

C521 10000p

GND SP OUT(L) POWER AMP IC501 LM1876TF

(Page 21)

The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.

Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.

HCD-NE3

• See page 17 for Circuit Boards Location.

6-10. PRINTED WIRING BOARDS – PANEL Section –

BACK LIGHT BOARD

JR102

JR103

JR106

R833

JW803 JW806

80 JW855

JW863

CNB806

D701

JW805 1 JW868

IC801

JR109 R881

JW857

JW858

JW832

JW860

JR101

R810

R818

R815

JW812

D809

D812

D810

JW833

D811

(Page 20) S809

TUNE +

TUNE –

JW846 JW862 R858

D806 (STANDBY)

JW829 JW824

R853

TAPE

JW865 JW848

R851

S802

S801

S803

1-861-725-

JW866

R891

R855

JW818

R890

JW822

JW844

JW853

JW843

R885 R886

D801

JW831

Q803

Q806

R883

JW870

JW817

JW845

Q804 E

E R884

C834

JW823

R871

JW815

Q805

R803

R852

R869 C832 JW816

D808

JW830 TUNER BAND

1 3

JW826

JW821

R870

R874

Q802

R854

S804

C828

C829

JW820

R879

JW850

R887

R804 C811

C813

R805

R895

RV801 ROTALY ENCODER VOLUME

JW819

IC803

R816

JW849

C816

JW814

R878

D807

JW828

JW813

F MAIN BOARD CN303

R860 S810

L801

JW811

R859

JR105

R814

R813

JW861 JW869

JW847

JW810

C810

S808

JW836

C827

R861

SUPPLIED WITH THE ASSEMBLED BLOCK

C815

R820 R875 (EXCEPT SP, TW, KR, AUS)

R862

JW871

JW809

R806

Q801

R823 R831

JW825

S811 DISPLAY

C823

R897

R822

(EXCEPT US, CND)

C812

R809

R706

(US, CND) R701

R863

R705

R812

C805

BASS/TREBLE

(EXCEPT AEP, UK) R876

S813 DSGX

R811

R840

JW842

R898

R824

S812

C824

S801 – 813

R857

R856 CNB801

S806 S805 CD SYNCHRO

REC PAUSE/START

J TAPE MECHANISM DECK BLOCK SUPPLIED WITH THE ASSEMBLED BLOCK

FM/AM TUNER PACK

R836

R825

JW840

JW838

R702

X802

JW867

JW835

R882

(Page 20) C831

C809

R826

C802

C801

X801

R832

R837

IC802

CNB303

R827

JW837

JW807

JW839

JR104

JW859

C830

CNB802

JW808

R801

MAIN BOARD CN302

JW864

R703

R704

CNB804

JW856

JW834

S820 CD LID OPEN/CLOSE DETECT

C814

C803

100

JW827

JW802

(11)

R834

JW801

Q808

R708 R707

R835

C826

G-4 H-10 H-10 H-11 H-10 H-13 C-4

LCD801 LIQUID CRYSTAL DISPLAY

R710 R709

1-861-730-

Q801 Q802 Q803 Q804 Q805 Q806 Q808

JW804

D701 – 703 LCD BACK LIGHT

JR107

R894

D-7 D-13 H-4

CNB302

R893

IC801 IC802 IC803

CONTROL BOARD

D702

R711

C804

R712

R838

C825

C-1 B-1 B-1 H-9 G-13 G-3 I-3 F-12 F-11 F-11 F-11

R892

D701 D702 D703 D801 D806 D807 D808 D809 D810 D811 D812

CNB807

Location

D703

Ref. No.

R839

• Semiconductor Location

:Uses unleaded solder.

S807 PLAY MODE

(11)

FM 75Ω (COAXIAL) ANTENNA AM

HCD-NE3

6-11. SCHEMATIC DIAGRAM – PANEL Section –

• See page 28 for Waveforms.

• See page 30 for IC Pin Function Description.

LCD801

COM0

COM1

COM2

COM3

SEG32

SEG31

SEG30

SEG29

SEG28

SEG27

SEG26

SEG25

SEG24

SEG23

SEG22

SEG21

SEG20

SEG19

SEG18

SEG17

SEG16

SEG15

SEG14

SEG13

SEG12

SEG11

SEG10

SEG9

SEG8

SEG7

SEG6

SEG5

SEG4

SEG3

SEG2

SEG1

SEG33

LIQUID CRYSTAL DISPLAY

D701-703

R707 120

(LCD BACK LIGHT)

CNB806 2P

COM0

COM1

COM2

COM3

SEG33

SEG32

SEG31

SEG30

SEG28

SEG27

SEG26

SEG25

SEG24

SEG23

SEG22

SEG21

SEG20

SEG19

SEG18

SEG17

SEG16

SEG15

SEG14

SEG13

SEG12

SEG11

SEG10

SEG9

SEG8

SEG7

SEG6

SEG5

SEG4

SEG3

SEG2

SEG1

SEG29

D701 SELS6B14CS-TP5

CNB807 2P

BLTC803

R708 120

R709 120 D702 SELS6B14CS-TP5

0.01

R710 120

BLT+ R832 47k SEG26

SEG25

SEG24

SEG23

SEG22

SEG21

SEG20

SEG19

SEG18

SEG17

SEG16

SEG15

SEG14

SEG13

SEG12

SEG11

SEG10

SEG27

R711 120

SEG9

SEG8

SEG7

SEG6

SEG5

SEG4

R833 47k

SEG3

SEG2

R851 3.3k

SEG1

R858 3.3k

D703 SELS6B14CS-TP5

R703 10k

S808

R704 100k

CNB302 19P

SEG27

SEG26

SEG25

VDD2

VSS2

SEG24

SEG23

SEG22

SEG21

SEG20

SEG19

SEG18

SEG17

SEG16

SEG15

SEG14

SEG12

SEG11

SEG10

SEG9

SEG8

SEG7

SEG6

SEG5

SEG4

SEG3

SEG2

SEG1

BIAS3

S801

SEG13

LED DRIVE

TU RCH

LCD BIAS2

SEG28

LCD BIAS1

SEG29

LCD COM0

SEG30

TU GND TU LCH

SEG31

LCD COM1

TU RCH TU-RCH TU GND TU GND

S803

TU LCH

TU 10V 35 TU-CE 32

VSS3

TU LED

100

VDD3

TA LED

R838

100

POWER ON TA PLAY SW

SYSTEM CONTROLLER

TA END SW

IC801 LC877456C-53K5-E

92 93

R839

100

TUNE +

S804

98 39

TA BIAS TA SOL

AMP STBY I POWER MONITOR

100

R831

100

R824

100

R823

100

R840

47k

3.3V(MAIN) GND

R898 100k

C814 0.1

3.9V(SUB)

CNB804 2P

TU DI

RMC

F DATA

CD SCOR

KEY0

KEY1

GND

R897 100k

NC TA-SW

VOL ENCODER

AREA

I POWER DOWN

TU DO

VDD1

CF2

CF1

PWR ON

XT2

CD ON

CD SYNCHRO

VSS1

AU MUTE

S805

R825

TU MUTE

AMP MUTE 100

XT1

DISPLAY

I POWER MONITOR AC-DET R836 4.7k

TU CLK

R855 680

TU CE

BACK LIGHT ON 98

R861 470

100

AC DET

S811

100

R826 TU TUNED

BAND

R827

4 OPEN/CLOSE GND

R882 100k

D810 L801 10µH 1SS133T-77

R822 30

100

R820 29

56k

100 R818 27

100 R810 26

100 R811 25

100 R815 24

R814 23

47k

R813 22

20p C827 10 16V

R816 22k

AC DET

RV801 ROTALY ENCODER

R875 *

R895 10k

R879 10k R701 33k

(US,CND)

R705 27k

D809 1SS133T-77

(EXCEPT SP,TW,KR,AUS)

R706 3.3k

(EXCEPT US,CND)

18 C801

R812

R809

C812 0.01

27 SCOR

220k

X802 10MHz

100

390k 22p C802

32.768KHz

0.1 C830

X801

R857 1.5k

R806

100 R805 8

S807 PLAY MODE

100

S813 DSGX

R804

7 SENS

R801

8 CLOK

100

R863 1k

9 XLT

R803

100

REC PAUSE/START

22k

S806

3 XTACN XRST DATA

DETECT

R856 1k

S812 BASS/TREBLE

R702

2 CD ON

REMOTE CONTROL RECEIVER IC802 RPM7240-H9

VOLUME R878 10k

C832 0.01

C813 0.1

R881 100

V G

CNB801 7P

R869 10k

R870 10k

R874 10k

R876 *

C834 0.1

C828 0.01

(EXCEPT AEP,UK)

C829 0.01

C810 22 6.3V

C831 220p

C809 0.01

PLAY SW

SUPPLIED WITH THE ASSEMBLED

REC PACK

R871 10k

* R875

MOTOR 9V

R887 470

SOL9V

Q804 KTA1271Y-AT

BLOCK COM GND

2.2k (US,CND)

Q802 KTA1271Y-AT

END SW

D811 1SS133T-77

R894 22k 11

R891 4.7k

0 (SP,TW,KR,AUS) R886 1k

Q802,803

D801 1SS133T-77

D812 1SS133T-77

D808 1SS133T-77

* R876 R883 47k

4.7k (US,CND,E,E51,EA,MX,AR)

R885 47k

D806 SLR-342VRT32

PLUNGER DRIVE

R890 220

0 (AEP,UK) 1k (E,E51,EA,MX,AR)

(STANDBY)

R884 1k

VOLTAGE DETECT IC803 M62703SL-TP

C811 22 16V

Q803 KRC402-RTK

Q805 KRC402-RTK

Q804,805 CAPSTAN/REEL

LED DRIVE

C826 0.1

MOTOR DRIVE

Q801 KTC3875

O G

Q806 KRC402-RTK

TA GND

C824 47 6.3V

DECK BLOCK

TA 10V

TAPE MECHANISM

S820 CD LID OPEN/CLOSE

R862 680

CNB303 8P

(Page 21)

AMP-MUTE 18

TU STEREO

TA REC/PLAY

R837 4.7k

TU-CL

AMP-STBY

ST/BY

R854 470

TUNER

TU-DO

(Page 21)

MD LED

TA MOTOR

S810

TU-DI

REC/PB

AU-MUTE 91

RESET

BLOCK AM

THE ASSEMBLED

CD LED

F DATA

R853 330

R860 330

TU 10V

TA BIAS

C805 0.01

CD XLT

TUNED

TA GND 95

CD CLK

STEREO

TA 10V TA GND

CD SENS

TUNER PACK SUPPLIED WITH

R835 47k

SEG33

CD DATA

TU-LCH

LCD COM3

CD XRST

FM/AM

SEG32

CD OPEN

COAXIAL

LCD COM2

CD XTXCN

FM 75Ω

ANTENNA

C804 0.01

TU 10V TA 10V

SEG33

S809 TUNE -

TU 10V

SEG32

COM3

TAPE

0.1

33 MUTE

C815

CNB802 11P

C823 470 6.3V

SEG31

COM2

R852 220

TU-LCH

SEG30

COM1 S802

TU GND

SEG29 COM0

R859 220

TU-RCH

SEG28 R834 47k

R712 120

Q808 KTC3875

C816 0.1

C825 0.1

RESET

R892 47k

D807 1SS133T-77

SWITCH

R893 47k

HCD-NE3 6-12. PRINTED WIRING BOARD – POWER Board – • Semiconductor Location

:Uses unleaded solder.

Location

POWER BOARD (EXCEPT E, E51, EA, SP) (E, E51, EA, SP)

S901

JW909

JW906

-2 -1

VOLTAGE SELECTOR 220 – 240V 220 – 240V

JW904

110 – 120V (E, E51, SP) 120 – 127V (EA)

JW907 (EXCEPT E, E51, EA, SP)

B ∗

∗ NOT REPLACEABLE: BUILT IN TRANSFORMER

T902 MAIN POWER TRANSFORMER

C JW908

C908

D919 JW903

R910 T901 SUB POWER TRANSFORMER

D917

C909

C903

C910

R901

D911

R902

C901

C902

R904

C915

D916

D920

D921

C912

C913

C906 C905

D913

D914

D918

C911 D912

C907

D909

D907 D908

D910

LF901

JW910

R905

D923

RY901

D906

F-4 E-5 E-5 E-4 E-4 D-4 E-5 D-5 E-5 E-5 D-5 E-6 D-6 E-5 E-5 F-5 E-4 F-5

JW912

D906 D907 D908 D909 D910 D911 D912 D913 D914 D916 D917 D918 D919 D920 D921 D922 D923 D924

JW901

Ref. No.

• See page 17 for Circuit Boards Location.

JW911

8 1

D924 R903 (US, CND)

CN902

C914

CN901

R906

D922

11 1-861-727-

E (AC IN)

MAIN BOARD CNB301

(Page 20)

(11)

HCD-NE3

6-13. SCHEMATIC DIAGRAM – POWER Board –

T902

D921 1SS133T-77

R902 47k

D916 1N5401M

C908 0.022

D919 1N5401M

D917 1N5401M

C902 0.1

C910 0.022

D913 1N4002B

D911 1N4002B

TRANSFORMER

C901 0.1

C909 0.022 C903 0.1

C912 0.022

D914 1N4002B

D912 1N4002B

-1

-2

C911 0.022

JW909

R910 0.15 S901 VOLTAGE SELECTOR

* NOT REPLACEABLE: BUILT IN TRANSFORMER

R903 3.3M

110-120V

220-240V (E,E51,SP)

120-127V

220-240V (EA)

(E,E51,EA,SP)

CN902 8P

(US,CND)

-B

C913 0.01

GND +B

LF901 SUB +B

RELAY ON

RY901

D906 1SS133T-77

AC-DET

C914 47 25V

R906 *

D909 1SS133T-77

D907 1SS133T-77

D910 1SS133T-77

D908 1SS133T-77

R904 2.2k

R905 2.2k

D923 1SS133T-77

D924 1SS133T-77

JW907

PROTECT

(EXCEPT E,E51,EA,SP)

14V

(Page 21)

(EXCEPT E,E51,EA,SP)

R901 47k

D918 1N5401M

C906 0.022

D920 1SS133T-77

C907 0.022

C905 0.022

MAIN POWER

CN901 2P

(AC IN)

C915 0.1

T901 SUB POWER TRANSFORMER

D922 RB441Q-40T-77

* R906 1k (US,CND,AEP,UK,KR) 1.2k (EXCEPT US,CND,AEP,UK,KR)

The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.

Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.

HCD-NE3

• Waveforms – BD Board –

– MAIN Board –

– CONTROL Board –

• IC Block Diagrams – BD Board –

1 IC101 w; (TEI) (CD Play mode)

qa T301 4 (REC mode)

wa IC801 qd (XT2)

IC101

XRST

XTACN

IOVSS0

XTSL

LMUT

94 93

92 91 90 89

SYSM

DATA

VSS

98 97 96 95

EXCK SBSO SQCK SQSO

100 99

CLOK XLAT

VDD

SENS

ATCK SCLK

WFCK

XUGF

XPCK

C2PO

108 107 106 105 104 103 102 101

112 111 110 109

Approx. 400 mVp-p

GFS

SCOR

VDD

C4M

WDCK

COUT

CXD3058AR

3 Vp-p

150 Vp-p

CPU INTERFACE

SERVO INTERFACE

13 µs

30.5 µs

84 RMUT 83 IOVDD0

2 IC101 ws (FEI) (CD Play mode)

qs Q344 (Collector) (REC mode)

ws IC801 qh (CF2) 82 AVDD2 D/A COVERTER

Approx. 200 mVp-p

2.9 Vp-p

15 Vp-p

MIRR 1 DFCT 2 FOK 3

81 AOUT2 80 VREFR

LPF

MIRR DFCT FOK

79 AVSS2 78 AVSS1

VSS 4

77 VREFL 76 AOUT1

LPF

LOCK 5 MDP 6

75 AVDD1

SSTP 7

74 XVDD

IOVSS1 8

13 µs

SFDR SRDR TFDR TRDR FFDR FRDR

100 ns

3 IC101 ek (RFACO) (CD Play mode)

73 XTAI 72 XTAO

CLOCK GENERATOR

9 10 11 12 13 14

71 XVSS

PWM GENERATOR SERVO AUTO SEQUENCER

DIGITAL CLV

70 IOVSS2 69 TES1 68 TEST

IOVDD1 15 AVDD0 16

SERVO DSP

AVSS0 17

67 DOUT

DIGITAL OUT

0.6 Vp-p

66 IOVDD2 A/D CONVERTER

65 EMPHI 64 EMPH

E F TEI TEO

4 IC101 us (XTAO) (CD Play mode)

63 VDD

18 19 20 21

D/A INTERFACE

SELECTOR ERROR CORRECTOR

FEI 22 FEO 23 VC 24

62 BCK 61 PCMD 60 VSS

32k RAM

59 LRCK

EFM DEMODULATOR A B C D

3.4 Vp-p

25 26 27 28

SUM

SUB CODE PROCESSOR

ASYNMMETRY CORRECTOR

59 ns

ATT

DIGITAL PLL

AMP

DC/DC CONVERTER

58 LRCKI 57 PCMDI

DDVROUT DDVRSEN

BCKI

DDCR

AVDD5

AVSS5

CLTV FILO FILI PCO

AVSS3

VPCO VCTL

52 53 54 55

BIAS ASYI ASYO

RFC

AVDD3

39 40 41 42 43 44 45 46 47 48 49 50

RFACI

36 37 38

AVSS4

RFACO

33 34

AC_SUM

RFDCO

PDSENS

AVDD4

29 30 31 32

EQ_IN

APC

PB1N

PB1P

PB2P

PB2N

PB2O

PB1O

VOLIN1

VOLIN2

GND

TRE1

TRE2

VDD

CONT

VEE

REC1O

REC1N

REC2N

REC2O

INC2 INC1 INB2 INB1 INA2 INA1

OUT1 BAS1

OUT2 BAS2

IC302 6 7 10

VOLUME

28 27 26 25 24 23 22 21 20 19 18 17 16 15

BASS

VOLUME

TREBLE

CH1OUTF

VREF

CH1OUTR

MUTING

CH2OUTF

CH2OUTR

POWVCC

VREFIN

GND

CH2RIN

CH2FIN

CH1RIN

1 2

CH1FIN

OPOUT

OUTVREF

CH4CAPA

CH4IN

CH3FIN

CH3RIN

GND

MUTE

POWVCC

CH3OUTF

CH3OUTR

CH4OUTF

CH4OUTR

IC251

OPIN– OPIN+

PREVCC

HCD-NE3

BA5947FM

28 27 26 25 24 23 22 21 20 19 18 17 16 15

D D D D

+ – INTERFACE LEVEL SHIFT

INTERFACE INTERFACE

D D D D

11 12 13 14

– MAIN Board –

BD3881FV

BASS

TREBLE

LOGIC CONTROL

+ –

HCD-NE3

• IC Pin Function Description

CONTROL BOARD IC801 LC877456C-53K5-E (SYSTEM CONTROLLER) Pin No.

Pin Name

I/O

PWR ON

Power relay drive signal output terminal

CD ON

Power on/off control signal output for the CD mechanism section

CD XTXCN

Oscillation circuit control signal output to the CD DSP “H”: auto oscillation, “L”: oscillation off

CD OPEN

CD lid open/close detection switch input terminal

CD XRST

Reset signal output to the CD DSP

CD DATA

Serial data output to the CD DSP

CD SENS

Internal status (SENSE) signal input from the CD DSP

CD CLK

Serial data transfer clock signal output to the CD DSP

CD XLT

Serial data latch pulse output to the CD DSP

—

Not used

RESET

Reset signal input from the reset switch “L”: reset For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”

XT1

Sub system clock input terminal (32.768 kHz)

XT2

Sub system clock output terminal (32.768 kHz)

VSS1

—

Ground terminal

CF1

Main system clock input terminal (10 MHz)

CF2

Main system clock output terminal (10 MHz)

VDD1

—

Power supply terminal (+3.2V)

I POWER MONITOR

19, 20

—

AREA

Model destination setting terminal

VOL ENCODER

Dial pulse input of the rotary encoder (for VOLUME control)

I POWER DOWN

Power down detection signal input terminal

TA-SW

Cassette in/out detect switch signal input from the tape mechanism deck

25, 26

KEY1, KEY0

Front panel key input terminal (A/D input)

CD SCOR

Subcode sync (S0+S1) detection signal input from the CD DSP

F DATA

Serial data output to the electrical volume

RMC

Remote control signal input from the remote control receiver

TU DI

Serial data input from the FM/AM tuner unit

—

Not used

TU DO

Serial data output to the FM/AM tuner unit

TU MUTE

Tuner muting on/off control signal output to the FM/AM tuner unit

TU CLK

serial data transfer clock signal output to the FM/AM tuner unit

TU CE

Chip enable signal output to the FM/AM tuner unit

TU TUNED

Tuning detection signal input from the FM/AM tuner unit

TU STEREO

FM stereo detection signal input from the FM/AM tuner unit

—

Not used

ST/BY

LED drive signal output terminal

MD LED

LED drive signal output terminal

Description “H”: on

Power monitor input terminal Not used

“L”: power down, normally : “H” “L”: cassette in

HCD-NE3

Pin No.

Pin Name

I/O

TA LED

LED drive signal output terminal

TU LED

LED drive signal output terminal

CD LED

LED drive signal output terminal

—

Not used

Segment drive signal output to the fluorescent indicator tube

45 to 53 SEG33 to SEG25

Description

VDD2

—

Power supply terminal (+3.1V)

VSS2

—

Ground terminal

56 to 79

SEG24 to SEG1

Segment drive signal output to the fluorescent indicator tube

BIAS3

Power supply output for the liquid crystal display bias

LCD BIAS2

Power supply output for the liquid crystal display bias

LCD BIAS1

Power supply output for the liquid crystal display bias

83 to 86

LCD COM0 to LCD COM3

Common drive signal output to the liquid crystal display (D621)

87, 88

—

Not used

VSS3

—

Ground terminal

VDD3

—

Power supply terminal (+3.1V)

TA PLAY SW

PLAY switch signal input from the tape mechanism deck

TA END SW

END switch signal input from the tape mechanism deck

TA MOTOR

Capstan/reel motor on/off control signal output terminal

TA REC/PLAY

Recording/playback selection signal output terminal

TA BIAS

Recording bias on/off selection signal output terminal “H”: bias on, “L”: bias off

TA SOL

Trigger plunger on/off control signal output terminal

BACK LIGHT ON

LED drive signal output terminal for the LCD back light

AMP STBY

Standby control signal output to the power amplifier

AMP MUTE

Tuner muting on/off control signal output to the power amplifier

100

AU MUTE

Line muting on/off control signal output terminal

“H”: motor on

“H”: playback mode, “L”: recording mode

“H”: plunger on

Not used

HCD-NE3 SECTION 7 EXPLODED VIEWS NOTE: • Items marked “*” are not stocked since they • -XX and -X mean standardized parts, so they are seldom required for routine service. Some may have some difference from the original delay should be anticipated when ordering one. these items. • Color Indication of Appearance Parts • The mechanical parts with no reference numExample: ber in the exploded views are not supplied. KNOB, BALANCE (WHITE) . . . (RED) • Accessories are given in the last of the elec↑ ↑ trical parts list. Parts Color Cabinet's Color • Abbreviation AR : Argentina model E51 : Chilean and Peruvian model MX : Mexican model AUS : Australian model EA : Saudi Arabia model SP : Singapore model CND : Canadian model KR : Korea model TW : Taiwan model

The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiquens pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.

7-1. PANEL SECTION

not supplied

3 #1 #1

top panel assy #8 not supplied (REG board) (1/2)

8 #8

#8 #1

not supplied #1

#1 #8

front panel assy-1 #1

4 #1

7 #1

#1 not supplied not supplied (REG board) (2/2) Ref. No.

Part No.

Description

1 1 1 1 1

A-1055-614-A A-1056-003-A A-1056-266-A A-1056-495-A A-1056-526-A

POWER BOARD, COMLETE (E, E51, SP) POWER BOARD, COMLETE (AR, AUS) POWER BOARD, COMLETE (MX, TW) POWER BOARD, COMLETE (EA) POWER BOARD, COMLETE (KR)

1 1 2 3 4

A-4750-273-A A-4751-335-A A-4750-277-A A-4750-275-A 3-703-244-00

POWER BOARD, COMLETE (AEP, UK) POWER BOARD, COMLETE (US, CND) AMP BOARD, COMPLETE MAIN BOARD, COMPLETE BUSHING (2104), CORD

05 05 05 05 05

1-775-790-12 1-769-079-23 1-769-744-52 1-696-570-21 1-783-531-22

CORD, POWER (AUS) CORD, POWER (KR) CORD, POWER (AEP, UK, E51, SP) CORD, POWER (EA) CORD, POWER (US, CND)

05 05 05

1-829-387-11 CORD, POWER (AR) 1-827-226-11 CORD, POWER (E, MX) 1-827-597-31 CORD, POWER (TW)

Remark

T902 Ref. No. 6 6 6 7 8 9 10 0 T902

Part No.

Description

Remark

1-693-625-11 TUNER (FM/AM) (US, CND) 1-693-628-11 TUNER (FM/AM) (E, E51, EA, MX, SP, TW, AR, AUS) 1-693-629-11 TUNER (FM/AM) (AEP, UK, KR) 4-246-784-01 FOOT RUBBER 4-253-221-01 CABINET, REAR

0 T902 0 T902

3-701-748-00 CLAMP 1-500-386-11 FILTER, CLAMP (FERRITE CORE) 1-443-246-11 TRANSFORMER, POWER (E, E51, MX, SP, TW, AR, AUS) 1-443-245-11 TRANSFORMER, POWER (AEP, UK) 1-443-244-11 TRANSFORMER, POWER (US, CND)

0 T902 0 T902 #1 #8 #5

1-443-396-11 1-443-397-11 7-685-647-79 7-685-646-79 7-685-661-14

TRANSFORMER, POWER (EA) TRANSFORMER, POWER (KR) SCREW +BVTP 3X10 TYPE2 N-S SCREW +BVTP 3X8 TYPE2 N-S SCREW +BVTP 4X12 TYPE2 N-S

HCD-NE3

7-2. FRONT PANEL ASSY-1

57 not supplied

54 57

not supplied

not supplied (back light board)

not supplied not supplied

55 not supplied

not supplied (HP board)

not supplied

front panel assy-2

Ref. No.

Part No.

Description

Remark

51 54 54 54 54

4-253-222-01 A-1055-611-A A-1056-204-A A-1056-001-A A-1056-250-A

KNOB, VOLUME CONTROL BOARD, COMPLETE (SP) CONTROL BOARD, COMPLETE (E, E51, AR) CONTROL BOARD, COMPLETE (TW, AUS) CONTROL BOARD, COMPLETE (MX)

A-1056-496-A CONTROL BOARD, COMPLETE (EA)

Ref. No. 54 54 54 55 57

Part No.

Description

Remark

A-1056-524-A A-4750-270-A A-4751-333-A 3-921-725-01 4-951-620-11

CONTROL BOARD, COMPLETE (KR) CONTROL BOARD, COMPLETE (AEP, UK) CONTROL BOARD, COMPLETE (US, CND) SCREW (2.6X10), +PWH SCREW (2.6X10), +BVTP

HCD-NE3

7-3. FRONT PANEL ASSY-2

106

107 108

not supplied

104 109

103

105 #6 not supplied

112 111

101

102

111 111 not supplied

110

Ref. No.

Part No.

Description

101 102 103 104 105

X-4956-276-1 4-245-034-01 4-245-018-01 4-238-631-01 4-246-784-01

LID, CASS ASSY (X) SPRING (CASSETTE) HOLDER (CASSETTE) TAPE SPRING FOOT RUBBER

106

X-2022-201-1 PANEL ASSY, FRONT (E, E51, EA, MX, SP, TW, AR, AUS) X-4956-274-1 PANEL ASSY, FRONT (AEP, UK, KR)

106

Remark

Ref. No.

Part No.

Description

106 107 108 109 110

X-4956-277-1 4-231-841-01 4-231-825-01 4-224-104-41 1-796-352-41

PANEL ASSY, FRONT (US, CND) SPRING (HEART CAM-B) CAM (B), HEART DAMPER DECK, MECHANICAL (CMAL5Z220A)

111 112 #6

4-951-620-11 SCREW (2.6X10), +BVTP 3-701-748-00 CLAMP 7-685-862-09 SCREW +BVTT 2.6X6 (S)

Remark

HCD-NE3 Ver. 1.1 159

7-4. TOP PANEL ASSY

156 160 157 158 168

155 161

S820

170 154 167 153 154

153 151 not supplied

163

151

S101

166 not supplied

169

not supplied The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Ref. No.

Part No.

Description

151 153 154 155 156

3-921-725-01 3-931-379-31 3-931-379-21 4-242-171-01 4-246-193-01

SCREW (2.6X10), +PWH RUBBER, VIBRATION PROOF (GREEN) RUBBER, VIBRATION PROOF (RED) DAMPER 150 N HOLDER, CHUCK A

157 158 159 160 161

4-249-238-01 4-246-192-01 X-4956-278-1 4-246-191-11 4-245-015-21

MAGNET (18-30-5) BASE, CHUCK N CD ASSY, LID PLATE, MAGNET CABINET (TOP) (US, CND)

Remark

Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.

Ref. No.

Part No.

Description

161 163 166 0 167 168

4-245-015-31 1-827-991-11 A-4751-032-A 8-820-221-01 4-248-711-11

CABINET (TOP) (EXCEPT US, CND) WIRE (FLAT TYPE) (16 CORE) BD BOARD, COMPLETE OPTICAL PICK-UP KSM-213EDP/C2NP SPRING (CD)

4-951-620-01 4-247-493-01 1-771-853-11 1-692-960-11

SCREW (2.6X8), +BVTP COVER, CD SWITCH, DETECTION (LIMIT) SWITCH, PUSH (1KEY) (CD LID OPEN/CLOSE DETECT)

169 170 S101 S820

Remark

HCD-NE3 BACK LIGHT

AMP

SECTION 8 ELECTRICAL PARTS LIST

NOTE: • Items marked “*” are not stocked since they • Due to standardization, replacements in the are seldom required for routine service. parts list may be different from the parts speciSome delay should be anticipated when orderfied in the diagrams or the components used ing these items. on the set. • SEMICONDUCTORS • -XX and -X mean standardized parts, so they In each case, u: µ, for example: may have some difference from the original uA. . : µA. . uPA. . : µPA. . one. uPB. . : µPB. . uPC. . : µPC. . • RESISTORS uPD. . : µPD. . All resistors are in ohms. • CAPACITORS METAL: Metal-film resistor. uF: µF METAL OXIDE: Metal oxide-film resistor. • COILS F: nonflammable uH: µH • Abbreviation AR : Argentina model E51 : Chilean and Peruvian model MX : Mexican model AUS : Australian model EA : Saudi Arabia model SP : Singapore model CND : Canadian model KR : Korea model TW : Taiwan model Ref. No.

Part No.

Description

Remark

Ref. No.

Part No.

Description

Remark

R518 1-216-841-11 METAL CHIP 47K 5% 1/10W 0 R519 1-215-889-00 METAL OXIDE 330 5% 2W F 0 R520 1-215-889-00 METAL OXIDE 330 5% 2W F ************************************************************

A-4750-277-A AMP BOARD, COMPLETE ******************** < CAPACITOR > C501 C503 C505 C506 C507

1-162-927-11 1-126-947-11 1-162-927-11 1-126-947-11 1-107-826-11

CERAMIC CHIP ELECT CERAMIC CHIP ELECT CERAMIC CHIP

100PF 47uF 100PF 47uF 0.1uF

5% 20% 5% 20% 10%

50V 35V 50V 35V 16V

C509 C510 C511 C512 C513

1-126-949-11 1-126-949-11 1-136-177-00 1-136-177-00 1-136-177-00

ELECT ELECT FILM FILM FILM

220uF 220uF 1uF 1uF 1uF

20% 20% 5% 5% 5%

35V 35V 50V 50V 50V

C514 C516

1-136-177-00 FILM 1-126-933-11 ELECT

1uF 100uF

5% 20%

50V 16V

BACK LIGHT BOARD **************** < LED > D701

8-719-075-50 LED SELS6B14C-TP5 (LCD BACK LIGHT)

D702

8-719-075-50 LED SELS6B14C-TP5 (LCD BACK LIGHT)

D703

8-719-075-50 LED SELS6B14C-TP5 (LCD BACK LIGHT) < RESISTOR >

< CONNECTOR > CN501

1-564-507-11 PLUG, CONNECTOR 4P

120 120 120 120 120

5% 5% 5% 5% 5%

1/10W 1/10W 1/10W 1/10W 1/10W

A-4751-032-A BD BOARD, COMPLETE ****************** < CAPACITOR >

8-759-333-24 IC LM1876TF < RESISTOR >

R501 R502 R503 R504 R505

1-216-821-11 1-216-841-11 1-216-819-11 1-249-437-11 1-216-841-11

METAL CHIP METAL CHIP METAL CHIP CARBON METAL CHIP

1K 47K 680 47K 47K

5% 5% 5% 5% 5%

1/10W 1/10W 1/10W 1/4W 1/10W

R506 R507 R508 R509 R511

1-216-821-11 1-216-833-11 1-216-819-11 1-249-437-11 1-216-839-11

METAL CHIP METAL CHIP METAL CHIP CARBON METAL CHIP

1K 10K 680 47K 33K

5% 5% 5% 5% 5%

1/10W 1/10W 1/10W 1/4W 1/10W

R512 R514 0 R515 0 R516 R517

1-216-839-11 1-216-833-11 1-216-373-81 1-216-373-81 1-216-842-11

METAL CHIP METAL CHIP METAL OXIDE METAL OXIDE METAL CHIP

33K 10K 2.2 2.2 56K

5% 5% 5% 5% 5%

1/10W 1/10W 2W F 2W F 1/10W

METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP

1-537-770-21 TERMINAL BOARD, GROUND < IC >

IC501

1-216-810-11 1-216-810-11 1-216-810-11 1-216-810-11 1-216-810-11

R712 1-216-810-11 METAL CHIP 120 5% 1/10W ************************************************************

< EARTH TERMINAL > EP903

R707 R708 R709 R710 R711

C10 C11 C14 C15 C16

1-165-989-11 1-165-989-11 1-164-360-11 1-164-360-11 1-115-156-11

CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP

10uF 10uF 0.1uF 0.1uF 1uF

10% 10%

6.3V 6.3V 16V 16V 10V

C17 C18 C111 C112 C113

1-126-923-11 1-162-964-11 1-162-967-11 1-164-315-11 1-162-967-11

ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP

220uF 0.001uF 0.0033uF 470PF 0.0033uF

20% 10% 10% 5% 10%

16V 50V 50V 50V 50V

C114 C115 C116 C117 C122

1-164-315-11 1-164-360-11 1-126-923-11 1-164-360-11 1-107-826-11

CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP

470PF 0.1uF 220uF 0.1uF 0.1uF

5% 20% 10%

50V 16V 16V 16V 16V

C123 C124

1-107-826-11 CERAMIC CHIP 1-162-959-11 CERAMIC CHIP

0.1uF 330PF

10% 5%

16V 50V

HCD-NE3 BD Ref. No.

Part No.

Description

Remark

JR111

25V 16V 50V 16V 16V

Q10

1-164-360-11 CERAMIC CHIP 1-162-927-11 CERAMIC CHIP 1-125-891-11 CERAMIC CHIP

0.1uF 100PF 0.47uF

C133 C141 C142 C143 C151

1-162-970-11 1-107-826-11 1-162-965-11 1-164-360-11 1-126-923-11

CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT

0.01uF 0.1uF 0.0015uF 0.1uF 220uF

C160 C161 C162 C163 C164

1-164-360-11 1-164-360-11 1-164-360-11 1-164-360-11 1-164-360-11

CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP

0.1uF 0.1uF 0.1uF 0.1uF 0.1uF

C170 C171 C172 C174 C181

1-126-934-11 1-162-919-11 1-162-920-11 1-164-360-11 1-164-360-11

ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP

220uF 22PF 27PF 0.1uF 0.1uF

C182 C183 C184 C185 C186

1-164-360-11 1-126-923-11 1-126-923-11 1-164-315-11 1-164-315-11

CERAMIC CHIP ELECT ELECT CERAMIC CHIP CERAMIC CHIP

0.1uF 220uF 220uF 470PF 470PF

C194 C195 C201 C202 C203

1-164-360-11 1-164-360-11 1-126-923-11 1-164-360-11 1-126-923-11

CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP ELECT

0.1uF 0.1uF 220uF 0.1uF 220uF

20% 20%

16V 16V 16V 16V 16V

C210 C211 C212 C213 C251

1-107-826-11 1-164-230-11 1-162-919-11 1-162-919-11 1-162-969-11

CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP

0.1uF 220PF 22PF 22PF 0.0068uF

10% 5% 5% 5% 10%

16V 50V 50V 50V 25V

C252 C257 C258 C259

1-164-360-11 1-164-360-11 1-164-360-11 1-164-360-11

CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP

0.1uF 0.1uF 0.1uF 0.1uF

< CONNECTOR > CN101 CN201

1-793-907-11 CONNECTOR, FFC/FPC 16P 1-568-860-11 SOCKET, CONNECTOR 17P

5% 10% 10% 10% 10% 20%

16V 16V 16V 16V 16V 20% 5% 5%

20% 20% 5% 5%

Ref. No.

16V 50V 10V

C125 C131 C132

16V 50V 50V 16V 16V 16V 16V 16V 50V 50V

16V 16V 16V 16V

Part No.

CONTROL

Description

1-216-296-11 SHORT CHIP

Remark 0

< TRANSISTOR > 6-550-363-01 TRANSISTOR

2SB1690KT146

< RESISTOR/FERRITE BEAD >

R10 R11 R12 R13 R111

1-216-791-11 1-216-864-11 1-216-845-11 1-218-446-11 1-216-821-11

METAL CHIP SHORT CHIP METAL CHIP METAL CHIP METAL CHIP

3.3 0 100K 1 1K

1/10W

5% 5% 5%

1/10W 1/10W 1/10W

R112 R113 R114 R121 R131

1-216-835-11 1-216-821-11 1-216-835-11 1-216-835-11 1-216-857-11

METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP

15K 1K 15K 15K 1M

5% 5% 5% 5% 5%

1/10W 1/10W 1/10W 1/10W 1/10W

R132 R133 R141 R142 R143

1-216-833-11 1-216-848-11 1-216-829-11 1-216-821-11 1-216-827-11

METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP

10K 180K 4.7K 1K 3.3K

5% 5% 5% 5% 5%

1/10W 1/10W 1/10W 1/10W 1/10W

R151 R161 R162 R171 R172

1-216-864-11 1-216-809-11 1-216-841-11 1-216-817-11 1-216-857-11

SHORT CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP

0 100 47K 470 1M

5% 5% 5% 5%

1/10W 1/10W 1/10W 1/10W

R173 R181 R182 R201 R202

1-216-295-00 1-216-809-11 1-216-809-11 1-500-445-21 1-216-864-11

SHORT CHIP 0 METAL CHIP 100 5% METAL CHIP 100 5% FERRITE, EMI (SMD) (2012) SHORT CHIP 0

R204 R251 R252 R406 R407

1-500-445-21 1-216-833-11 1-216-837-11 1-216-809-11 1-216-809-11

FERRITE, EMI (SMD) (2012) METAL CHIP 10K METAL CHIP 22K METAL CHIP 100 METAL CHIP 100

5% 5% 5% 5%

1/10W 1/10W 1/10W 1/10W

R408 R409 R410 R411 R412

1-216-809-11 1-216-809-11 1-216-809-11 1-216-809-11 1-216-809-11

METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP

5% 5% 5% 5% 5%

1/10W 1/10W 1/10W 1/10W 1/10W

100 100 100 100 100

1/10W 1/10W

< IC > < VIBRATOR > IC101 IC251

8-752-425-11 IC CXD3058AR 6-705-808-01 IC BA5947FM

X101 1-579-280-11 VIBRATOR, CRYSTAL (16.9344MHz) ************************************************************

< SHORT > JR101 JR102 JR103 JR104 JR105

1-216-296-11 1-216-296-11 1-216-296-11 1-216-296-11 1-216-296-11

SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP

0 0 0 0 0

JR106 JR107 JR108 JR109 JR110

1-216-296-11 1-216-296-11 1-216-864-11 1-216-296-11 1-216-296-11

SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP

0 0 0 0 0

A-1055-611-A A-1056-001-A A-1056-204-A A-1056-250-A A-1056-496-A

CONTROL BOARD, COMPLETE (SP) CONTROL BOARD, COMPLETE (TW, AUS) CONTROL BOARD, COMPLETE (E, E51, AR) CONTROL BOARD, COMPLETE (MX) CONTROL BOARD, COMPLETE (EA)

A-1056-524-A CONTROL BOARD, COMPLETE (KR) A-4750-270-A CONTROL BOARD, COMPLETE (AEP, UK) A-4751-333-A CONTROL BOARD, COMPLETE (US, CND) ************************ 4-245-030-01 HOLDER (LCD) 4-245-801-01 SHEET (LCD)

HCD-NE3 CONTROL Ref. No.

Part No.

Description

Remark

Ref. No. JR109

4-248-365-01 SHEET (PLATE) 4-248-366-01 SHEET (LIGHT)

Part No.

Description

1-216-864-11 SHORT CHIP

Remark 0

< COIL > < CAPACITOR > L801 C801 C802 C803 C804 C805

1-164-160-11 1-162-919-11 1-107-726-91 1-107-726-91 1-107-726-91

CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP

20PF 22PF 0.01uF 0.01uF 0.01uF

5% 5% 10% 10% 10%

50V 50V 16V 16V 16V

C809 C810 C811 C812 C813

1-107-726-91 1-124-222-91 1-124-234-00 1-107-726-91 1-107-826-11

CERAMIC CHIP ELECT ELECT CERAMIC CHIP CERAMIC CHIP

0.01uF 22uF 22uF 0.01uF 0.1uF

10% 20% 20% 10% 10%

16V 6.3V 16V 16V 16V

C814 C815 C816 C823 C824

1-107-826-11 1-107-826-11 1-107-826-11 1-104-655-91 1-124-589-11

CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT ELECT

0.1uF 0.1uF 0.1uF 470uF 47uF

10% 10% 10% 20% 20%

16V 16V 16V 6.3V 16V

C825 C826 C827 C828 C829

1-107-826-11 1-107-826-11 1-126-157-11 1-107-726-91 1-107-726-91

CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP

0.1uF 0.1uF 10uF 0.01uF 0.01uF

10% 10% 20% 10% 10%

16V 16V 16V 16V 16V

C830 C831 C832 C834

1-107-826-11 1-164-230-11 1-107-726-91 1-107-826-11

CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP

0.1uF 220PF 0.01uF 0.1uF

10% 5% 10% 10%

16V 50V 16V 16V

1-410-509-11 INDUCTOR

10uH

< LIQUID CRYSTAL DISPLAY > LCD801 1-805-530-11 DISPLAY PANEL, LIQUID CRYSTAL < TRANSISTOR >

< CONNECTOR > CNB302 CNB303 CNB801 CNB802

1-784-780-11 1-691-040-31 1-568-826-11 1-568-830-11

CONNECTOR, FFC 19P CONNECTOR, FFC 8P CONNECTOR, FFC 7P CONNECTOR, FFC 11P < DIODE >

D801 D806 D807 D808 D809

8-719-991-33 8-719-060-44 8-719-991-33 8-719-991-33 8-719-991-33

DIODE DIODE DIODE DIODE DIODE

1SS133T-77 SLR-342VRT32 1SS133T-77 1SS133T-77 1SS133T-77

D810 D811 D812

8-719-991-33 DIODE 1SS133T-77 8-719-991-33 DIODE 1SS133T-77 8-719-991-33 DIODE 1SS133T-77 < IC >

IC801 IC802 IC803

6-804-383-01 IC LC877456C-53K5-E 6-600-309-01 IC RPM7240-H9 8-759-532-64 IC M62703SL-TP < SHORT >

JR101 JR102 JR103 JR104 JR105

1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11

SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP

0 0 0 0 0

JR106 JR107

1-216-864-11 SHORT CHIP 1-216-864-11 SHORT CHIP

0 0

Q801 Q802 Q803 Q804 Q805

8-729-034-51 8-729-037-13 8-729-054-16 8-729-037-13 8-729-054-16

TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR

KTC3875 KTA1271Y KRC402-RTK KTA1271Y KRC402-RTK

Q806 Q808

8-729-054-16 TRANSISTOR 8-729-034-51 TRANSISTOR

KRC402-RTK KTC3875

< RESISTOR > R701

1-216-839-11 METAL CHIP

33K

1/10W (US, CND) 5% 1/10W 5% 1/10W 5% 1/10W 5% 1/10W (EXCEPT US, CND)

R702 R703 R704 R705

1-216-852-11 1-216-833-11 1-216-845-11 1-216-838-11

METAL CHIP METAL CHIP METAL CHIP METAL CHIP

390K 10K 100K 27K

R706

1-216-827-11 METAL CHIP

3.3K

R801 R803 R804 R805

1-216-809-11 1-216-809-11 1-216-809-11 1-216-809-11

METAL CHIP METAL CHIP METAL CHIP METAL CHIP

100 100 100 100

R806 R809 R810 R811 R812

1-216-821-11 1-216-849-11 1-216-809-11 1-216-809-11 1-216-809-11

METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP

1K 220K 100 100 100

5% 5% 5% 5% 5%

1/10W 1/10W 1/10W 1/10W 1/10W

R813 R814 R815 R816 R818

1-216-837-11 1-216-841-11 1-216-809-11 1-216-837-11 1-216-809-11

METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP

22K 47K 100 22K 100

5% 5% 5% 5% 5%

1/10W 1/10W 1/10W 1/10W 1/10W

R820 R822 R823 R824 R825

1-216-842-11 1-216-809-11 1-216-809-11 1-216-809-11 1-216-809-11

METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP

56K 100 100 100 100

5% 5% 5% 5% 5%

1/10W 1/10W 1/10W 1/10W 1/10W

R826 R827 R831 R832 R833

1-216-809-11 1-216-809-11 1-216-809-11 1-216-833-11 1-216-841-11

METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP

100 100 100 10K 47K

5% 5% 5% 5% 5%

1/10W 1/10W 1/10W 1/10W 1/10W

R834 R835 R836 R837 R838

1-216-841-11 1-216-841-11 1-216-829-11 1-216-829-11 1-216-809-11

METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP

47K 47K 4.7K 4.7K 100

5% 5% 5% 5% 5%

1/10W 1/10W 1/10W 1/10W 1/10W

R839

1-216-809-11 METAL CHIP

100

1/10W

5% 1/10W (EXCEPT US, CND) 5% 1/10W 5% 1/10W 5% 1/10W 5% 1/10W

HCD-NE3 CONTROL Ref. No.

Part No.

Description

R840 R851 R852 R853

1-216-841-11 1-216-827-11 1-216-813-11 1-216-815-11

METAL CHIP METAL CHIP METAL CHIP METAL CHIP

47K 3.3K 220 330

5% 5% 5% 5%

1/10W 1/10W 1/10W 1/10W

Remark

R854 R855 R856 R857 R858

1-216-817-11 1-216-819-11 1-216-821-11 1-216-823-11 1-216-827-11

METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP

470 680 1K 1.5K 3.3K

5% 5% 5% 5% 5%

1/10W 1/10W 1/10W 1/10W 1/10W

R859 R860 R861 R862 R863

1-216-813-11 1-216-815-11 1-216-817-11 1-216-819-11 1-216-821-11

METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP

220 330 470 680 1K

5% 5% 5% 5% 5%

1/10W 1/10W 1/10W 1/10W 1/10W

R869 R870 R871 R874 R875

1-216-833-11 1-216-833-11 1-216-833-11 1-216-833-11 1-216-821-11

METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP

10K 10K 10K 10K 1K

Ref. No.

Part No.

MAIN

Description

Remark

S808 S809 S810

1-786-050-21 SWITCH, KEY BOARD (x) 1-786-050-21 SWITCH, KEY BOARD (TUNE – . m) 1-786-050-21 SWITCH, KEY BOARD (TUNE + M >)

S811 S812

1-786-050-21 SWITCH, KEY BOARD (DISPLAY) 1-786-050-21 SWITCH, KEY BOARD (BASS/TREBLE)

S813

1-786-050-21 SWITCH, KEY BOARD (DSGX)

< VIBRATOR >

2.2K

5% 1/10W 5% 1/10W 5% 1/10W 5% 1/10W 5% 1/10W (E, E51, EA, MX, AR)

R875

1-216-825-11 METAL CHIP

R875 R876

1-216-864-11 SHORT CHIP 1-216-829-11 METAL CHIP

R876

1-216-864-11 SHORT CHIP

0 (SP, TW, KR, AUS)

R878

1-216-833-11 METAL CHIP

10K

1/10W

R879 R881 R882 R883 R884

1-216-833-11 1-247-807-31 1-216-845-11 1-216-841-11 1-216-821-11

METAL CHIP CARBON METAL CHIP METAL CHIP METAL CHIP

10K 100 100K 47K 1K

5% 5% 5% 5% 5%

1/10W 1/4W 1/10W 1/10W 1/10W

R885 R886 R887 R890 R891

1-216-841-11 1-216-821-11 1-216-817-11 1-216-813-11 1-216-829-11

METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP

47K 1K 470 220 4.7K

5% 5% 5% 5% 5%

1/10W 1/10W 1/10W 1/10W 1/10W

R892 R893 R894 R895 R897

1-216-841-11 1-216-841-11 1-216-837-11 1-216-833-11 1-216-845-11

METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP

47K 47K 22K 10K 100K

5% 5% 5% 5% 5%

1/10W 1/10W 1/10W 1/10W 1/10W

R898

1-216-845-11 METAL CHIP

100K

1/10W

X801

1-760-252-12 VIBRATOR, CRYSTAL (32.768kHz)

X802 1-795-004-21 VIBRATOR, CERAMIC (10MHz) ************************************************************ HP BOARD ********* < CAPACITOR > C520 C521

1-127-876-21 CERAMIC 1-127-876-21 CERAMIC

1/10W (US, CND)

0 (AEP, UK) 4.7K 5% 1/10W (US, CND, E, E51, EA, MX, AR)

0.01uF 0.01uF

10% 10%

50V 50V

< JACK > J301 1-793-829-11 JACK, HEADPHONE (PHONES) ************************************************************ A-4750-275-A MAIN BOARD, COMPLETE ********************* < CAPACITOR >

< ROTARY ENCODER > RV801

1-418-632-11 ENCODER, ROTARY (12 TYPE) (VOLUME)

< SWITCH > S801 S802 S803 S804 S805

1-786-050-21 1-786-050-21 1-786-050-21 1-786-050-21 1-786-050-21

SWITCH, KEY BOARD (I/1) SWITCH, KEY BOARD (TAPE N) SWITCH, KEY BOARD (CD NX) SWITCH, KEY BOARD (TUNER, BAND) SWITCH, KEY BOARD (CD SYNCHRO)

S806 S807

1-786-050-21 SWITCH, KEY BOARD (z REC PAUSE/START) 1-786-050-21 SWITCH, KEY BOARD (PLAY MODE)

C101 C102 C103 C104 C106

1-162-925-11 1-162-977-11 1-162-927-11 1-104-665-11 1-164-227-11

CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP

68PF 0.0018uF 100PF 100uF 0.022uF

5% 10% 5% 20% 10%

50V 50V 50V 25V 25V

C107 C108 C109 C110 C111

1-126-961-11 1-162-967-11 1-162-962-11 1-164-218-11 1-162-967-11

ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP

2.2uF 0.0033uF 470PF 180PF 0.0033uF

20% 10% 10% 5% 10%

50V 50V 50V 50V 50V

C112 C113 C114 C115 C116

1-162-968-11 1-126-957-11 1-126-959-11 1-126-963-11 1-162-962-11

CERAMIC CHIP ELECT ELECT ELECT CERAMIC CHIP

0.0047uF 0.22uF 0.47uF 4.7uF 470PF

10% 20% 20% 20% 10%

50V 50V 50V 50V 50V

C117 C118 C119 C121 C126

1-164-730-11 1-164-677-11 1-107-726-91 1-107-826-11 1-162-960-11

CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP

0.0012uF 0.033uF 0.01uF 0.1uF 220PF

10% 10% 10% 10% 10%

50V 16V 16V 16V 50V

C127 C132 C133 C134 C135

1-162-962-11 1-126-963-11 1-130-491-00 1-162-966-11 1-126-964-11

CERAMIC CHIP ELECT MYLAR CERAMIC CHIP ELECT

470PF 4.7uF 0.047uF 0.0022uF 10uF

10% 20% 5% 10% 20%

50V 50V 50V 50V 50V

C136 C201 C202 C203

1-126-964-11 1-162-925-11 1-162-977-11 1-162-927-11

ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP

10uF 68PF 0.0018uF 100PF

20% 5% 10% 5%

50V 50V 50V 50V

HCD-NE3 MAIN Ref. No.

Part No.

Description

Remark

C204

1-104-665-11 ELECT

100uF

20%

25V

C206 C207 C208 C209 C210

1-164-227-11 1-126-961-11 1-162-967-11 1-162-962-11 1-164-218-11

CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP

0.022uF 2.2uF 0.0033uF 470PF 180PF

10% 20% 10% 10% 5%

25V 50V 50V 50V 50V

C211 C212 C213 C214 C215

1-162-967-11 1-162-968-11 1-126-957-11 1-126-959-11 1-126-963-11

CERAMIC CHIP CERAMIC CHIP ELECT ELECT ELECT

0.0033uF 0.0047uF 0.22uF 0.47uF 4.7uF

10% 10% 20% 20% 20%

50V 50V 50V 50V 50V

C216 C217 C218 C219 C221

1-162-962-11 1-164-730-11 1-164-677-11 1-107-726-91 1-107-826-11

CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP

470PF 0.0012uF 0.033uF 0.01uF 0.1uF

10% 10% 10% 10% 10%

50V 50V 16V 16V 16V

C226 C227 C232 C233 C234

1-162-960-11 1-162-962-11 1-126-963-11 1-130-491-00 1-162-966-11

CERAMIC CHIP CERAMIC CHIP ELECT MYLAR CERAMIC CHIP

220PF 470PF 4.7uF 0.047uF 0.0022uF

10% 10% 20% 5% 10%

50V 50V 50V 50V 50V

C235 C236 C301 C302 C305

1-126-964-11 1-126-964-11 1-162-915-11 1-104-655-91 1-104-655-91

ELECT ELECT CERAMIC CHIP ELECT ELECT

10uF 10uF 10PF 470uF 470uF

20% 20% 0.5PF 20% 20%

50V 50V 50V 6.3V 6.3V

C308 C309 C310 C311 C312

1-107-826-11 1-126-767-11 1-127-888-21 1-128-809-11 1-162-960-11

CERAMIC CHIP ELECT CERAMIC CERAMIC CERAMIC CHIP

0.1uF 1000uF 0.1uF 100PF 220PF

10% 20% 10% 5% 10%

16V 16V 50V 50V 50V

C313 C314 C315 C316 C317

1-126-933-11 1-137-150-11 1-128-809-11 1-162-927-11 1-128-809-11

ELECT FILM CERAMIC CERAMIC CHIP CERAMIC

100uF 0.01uF 100PF 100PF 100PF

20% 5% 5% 5% 5%

16V 100V 50V 50V 50V

C318 C319 C320 C321 C322

1-162-927-11 1-162-927-11 1-107-726-91 1-115-416-11 1-115-416-11

CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP

100PF 100PF 0.01uF 0.001uF 0.001uF

5% 5% 10% 5% 5%

50V 50V 16V 25V 25V

C323 C324 C326 C328 C329

1-126-943-11 1-126-934-11 1-162-966-11 1-126-935-11 1-126-916-11

ELECT ELECT CERAMIC CHIP ELECT ELECT

2200uF 220uF 0.0022uF 470uF 1000uF

20% 20% 10% 20% 20%

25V 16V 50V 16V 6.3V

C330 C331 C332 C333 C335

1-104-665-11 1-107-726-91 1-126-927-11 1-126-969-11 1-107-726-91

ELECT CERAMIC CHIP ELECT ELECT CERAMIC CHIP

100uF 0.01uF 2200uF 220uF 0.01uF

20% 10% 20% 20% 10%

25V 16V 10V 50V 16V

C336 C345 C346 C351 C352

1-126-965-11 1-126-964-11 1-126-768-11 1-104-665-11 1-126-953-11

ELECT ELECT ELECT ELECT ELECT

22uF 10uF 2200uF 100uF 2200uF

20% 20% 20% 20% 20%

50V 50V 16V 25V 35V

C353

1-126-953-11 ELECT

2200uF

20%

35V

Ref. No.

Part No.

Description

C354 C355 C356 C357

1-126-961-11 1-130-485-00 1-130-481-00 1-130-481-00

ELECT MYLAR MYLAR MYLAR

2.2uF 0.015uF 0.0068uF 0.0068uF

20% 5% 5% 5%

50V 50V 50V 50V

Remark

C358 C360 C361 C362 C370

1-130-486-00 1-126-964-11 1-126-947-11 1-126-964-11 1-107-826-11

MYLAR ELECT ELECT ELECT CERAMIC CHIP

0.018uF 10uF 47uF 10uF 0.1uF

5% 20% 20% 20% 10%

50V 50V 35V 50V 16V

< CONNECTOR > CN302 CN303 CN305 CN309 CNB307

1-784-780-11 1-691-040-31 1-784-778-11 1-564-506-11 1-564-509-11

CONNECTOR, FFC 19P CONNECTOR, FFC 8P CONNECTOR, FFC 17P PLUG, CONNECTOR 3P PLUG, CONNECTOR 6P

* CNB308 1-564-512-11 PLUG, CONNECTOR 9P < DIODE > D301 D302 D303 D304 D305

8-719-991-33 8-719-991-33 8-719-109-72 8-719-109-72 8-719-983-20

DIODE DIODE DIODE DIODE DIODE

1SS133T-77 1SS133T-77 RD3.9ESB2 RD3.9ESB2 MTZJ-T-77-4.3C

D306 D307 D308 D310 D317

8-719-983-20 8-719-991-33 8-719-991-33 8-719-983-20 8-719-991-33

DIODE DIODE DIODE DIODE DIODE

MTZJ-T-77-4.3C 1SS133T-77 1SS133T-77 MTZJ-T-77-4.3C 1SS133T-77

D318 D321 D322

8-719-991-33 DIODE 1SS133T-77 8-719-991-33 DIODE 1SS133T-77 8-719-991-33 DIODE 1SS133T-77 < FERRITE BEAD >

FB301 FB302 FB317

1-412-473-21 INDUCTOR (SMALL TYPE) 1-412-473-21 INDUCTOR (SMALL TYPE) 1-500-445-21 FERRITE, EMI (SMD) (2012) < IC >

IC302

6-702-895-01 IC BD3881FV < JACK >

J302 J303

1-536-708-81 TERMINAL BOARD, PUSH (4P) (SPEAKER IMPEDANCE USE 8-16тДж) 1-778-940-11 JACK 2P (MD) < CAPACITOR/COIL >

JW120 JW323

1-107-826-11 CERAMIC CHIP 1-410-509-11 INDUCTOR

0.1uF 10uH

10%

< COIL > L101 L201

1-422-009-13 COIL, AIR-CORE 1-422-009-13 COIL, AIR-CORE < TRANSISTOR >

Q311 Q312

8-729-037-13 TRANSISTOR 8-729-036-86 TRANSISTOR

KTA1271Y KTC3203Y-AT

16V

HCD-NE3 MAIN Ref. No.

Part No.

Description

Remark

Q313 Q314 Q315

8-729-036-86 TRANSISTOR 8-729-037-13 TRANSISTOR 8-729-054-16 TRANSISTOR

KTC3203Y-AT KTA1271Y KRC402-RTK

Q317 Q319 Q320 Q326 Q327

8-729-028-54 8-729-040-76 8-729-054-16 8-729-034-50 8-729-034-50

TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR

KTC3205 KTA1273-Y-AT KRC402-RTK KTA1504 KTA1504

Q328 Q329 Q330 Q331 Q332

8-729-045-62 8-729-045-62 8-729-045-62 8-729-054-03 8-729-054-03

FET FET FET TRANSISTOR TRANSISTOR

2SK2158-T2B 2SK2158-T2B 2SK2158-T2B KRA303-RTK KRA303-RTK

Q333 Q338 Q339 Q342 Q343

8-729-054-16 8-729-054-16 8-729-036-86 8-729-120-28 8-729-120-28

TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR

KRC402-RTK KRC402-RTK KTC3203Y-AT 2SC1623-L5L6 2SC1623-L5L6

Q344 Q345 Q346 Q347 Q348

8-729-142-46 8-729-142-46 8-729-801-93 8-729-037-03 8-729-036-58

TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR

2SC2001-LK 2SC2001-LK 2SD1387-3 KTA1266GR-AT KRC102M-AT

< RESISTOR > R100 R101 R102 R103 R104

1-216-812-11 1-216-834-11 1-216-840-11 1-216-817-11 1-216-805-11

METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP

180 12K 39K 470 47

5% 5% 5% 5% 5%

1/10W 1/10W 1/10W 1/10W 1/10W

R105 R106 R107 R108 R109

1-216-852-11 1-216-830-11 1-216-847-11 1-216-835-11 1-216-825-11

METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP

390K 5.6K 150K 15K 2.2K

5% 5% 5% 5% 5%

1/10W 1/10W 1/10W 1/10W 1/10W

R111 R112 R113 R114 R115

1-216-825-11 1-216-839-11 1-216-817-11 1-216-818-11 1-216-827-11

METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP

2.2K 33K 470 560 3.3K

5% 5% 5% 5% 5%

1/10W 1/10W 1/10W 1/10W 1/10W

R116 R117 R118 R119 R120

1-216-832-11 1-216-825-11 1-218-867-11 1-216-824-11 1-216-833-11

METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP

8.2K 2.2K 6.8K 1.8K 10K

5% 5% 0.5% 5% 5%

1/10W 1/10W 1/10W 1/10W 1/10W

R121 R122 R123 R124 R125

1-216-825-11 1-216-843-11 1-216-825-11 1-216-835-11 1-216-837-11

METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP

2.2K 68K 2.2K 15K 22K

5% 5% 5% 5% 5%

1/10W 1/10W 1/10W 1/10W 1/10W

R126 R128 R131 R132 R136

1-216-837-11 1-216-822-11 1-216-822-11 1-216-821-11 1-216-833-11

METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP

22K 1.2K 1.2K 1K 10K

5% 5% 5% 5% 5%

1/10W 1/10W 1/10W 1/10W 1/10W

R137 R143 R200

1-216-829-11 METAL CHIP 1-216-832-11 METAL CHIP 1-216-812-11 METAL CHIP

4.7K 8.2K 180

5% 5% 5%

1/10W 1/10W 1/10W

The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.

Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.

Ref. No.

Part No.

Description

Remark

R201 R202

1-216-834-11 METAL CHIP 1-216-840-11 METAL CHIP

12K 39K

5% 5%

1/10W 1/10W

R203 R204 R205 R206 R207

1-216-817-11 1-216-805-11 1-216-852-11 1-216-830-11 1-216-847-11

METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP

470 47 390K 5.6K 150K

5% 5% 5% 5% 5%

1/10W 1/10W 1/10W 1/10W 1/10W

R208 R209 R211 R212 R213

1-216-835-11 1-216-825-11 1-216-825-11 1-216-839-11 1-216-817-11

METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP

15K 2.2K 2.2K 33K 470

5% 5% 5% 5% 5%

1/10W 1/10W 1/10W 1/10W 1/10W

R214 R215 R216 R217 R218

1-216-818-11 1-216-827-11 1-216-832-11 1-216-825-11 1-218-867-11

METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP

560 3.3K 8.2K 2.2K 6.8K

5% 5% 5% 5% 0.5%

1/10W 1/10W 1/10W 1/10W 1/10W

R219 R220 R221 R222 R223

1-216-824-11 1-216-833-11 1-216-825-11 1-216-843-11 1-216-825-11

METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP

1.8K 10K 2.2K 68K 2.2K

5% 5% 5% 5% 5%

1/10W 1/10W 1/10W 1/10W 1/10W

R224 R225 R226 R228 R231

1-216-835-11 1-216-837-11 1-216-837-11 1-216-822-11 1-216-822-11

METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP

15K 22K 22K 1.2K 1.2K

5% 5% 5% 5% 5%

1/10W 1/10W 1/10W 1/10W 1/10W

R232 R236 R237 R243 R301

1-216-821-11 1-216-833-11 1-216-829-11 1-216-832-11 1-216-841-11

METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP

1K 10K 4.7K 8.2K 47K

5% 5% 5% 5% 5%

1/10W 1/10W 1/10W 1/10W 1/10W

R302 R303 R304 R305 R315

1-216-835-11 1-216-833-11 1-216-821-11 1-216-809-11 1-216-821-11

METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP

15K 10K 1K 100 1K

5% 5% 5% 5% 5%

1/10W 1/10W 1/10W 1/10W 1/10W

R317 R318 R319 R320 R321

1-216-841-11 1-216-817-11 1-216-857-11 1-216-829-11 1-216-845-11

METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP

47K 470 1M 4.7K 100K

5% 5% 5% 5% 5%

1/10W 1/10W 1/10W 1/10W 1/10W

R322 R323 R324 R325 R326

1-216-823-11 1-216-821-11 1-216-825-11 1-216-845-11 1-216-845-11

METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP

1.5K 1K 2.2K 100K 100K

5% 5% 5% 5% 5%

1/10W 1/10W 1/10W 1/10W 1/10W

R327 R332 R336 R348 R349

1-216-833-11 1-216-821-11 1-216-829-11 1-216-821-11 1-216-842-11

METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP

10K 1K 4.7K 1K 56K

5% 5% 5% 5% 5%

1/10W 1/10W 1/10W 1/10W 1/10W

R350 R351 R352 0 R353 R358

1-216-833-11 1-216-833-11 1-249-413-11 1-212-958-00 1-216-842-11

METAL CHIP METAL CHIP CARBON FUSIBLE METAL CHIP

10K 10K 470 10 56K

5% 5% 5% 5% 5%

1/10W 1/10W 1/4W 1/2W F 1/10W

HCD-NE3 MAIN

POWER

REG

Ref. No.

Part No.

Description

Part No.

Description

R359 0 R360 0 R361 R362 R363

1-260-330-11 1-219-787-17 1-219-787-17 1-216-836-11 1-216-836-11

CARBON FUSIBLE FUSIBLE METAL CHIP METAL CHIP

1.5K 5.6 5.6 18K 18K

5% 5% 5% 5% 5%

1/2W 1/4W F 1/4W F 1/10W 1/10W

D911 D912 D913 D914 D916

8-719-063-79 8-719-063-79 8-719-063-79 8-719-063-79 8-719-046-47

DIODE DIODE DIODE DIODE DIODE

1N4002B 1N4002B 1N4002B 1N4002B 1N5401TM

R364 R365 R366 R367 R368

1-218-867-11 1-216-825-11 1-216-837-11 1-216-825-11 1-216-833-11

METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP

6.8K 2.2K 22K 2.2K 10K

0.5% 5% 5% 5% 5%

1/10W 1/10W 1/10W 1/10W 1/10W

D917 D918 D919 D920 D921

8-719-046-47 8-719-046-47 8-719-046-47 8-719-991-33 8-719-991-33

DIODE DIODE DIODE DIODE DIODE

1N5401TM 1N5401TM 1N5401TM 1SS133T-77 1SS133T-77

R370 R371 R372 R373

1-216-833-11 1-216-833-11 1-216-844-11 1-216-833-11

METAL CHIP METAL CHIP METAL CHIP METAL CHIP

10K 10K 82K 10K

5% 5% 5% 5%

1/10W 1/10W 1/10W 1/10W

D922 D923 D924

8-719-050-84 DIODE RB441Q-40T-77 8-719-991-33 DIODE 1SS133T-77 8-719-991-33 DIODE 1SS133T-77

Remark

Ref. No.

Remark

< LINE FILTER > < TRANSFORMER > 0 LF901 T301 1-423-980-11 TRANSFORMER, BIAS OSCILLATION ************************************************************ A-1055-614-A A-1056-003-A A-1056-266-A A-1056-495-A A-1056-526-A

POWER BOARD, COMPLETE (E, E51, SP) POWER BOARD, COMPLETE (AR, AUS) POWER BOARD, COMPLETE (MX, TW) POWER BOARD, COMPLETE (EA) POWER BOARD, COMPLETE (KR)

A-4750-273-A POWER BOARD, COMPLETE (AEP, UK) A-4751-335-A POWER BOARD, COMPLETE (US, CND) ***********************

1-402-663-11 TRANSFORMER, LINE FILTER (LFT) < RESISTOR >

R901 R902 0 R903

1-249-437-11 CARBON 1-249-437-11 CARBON 1-219-237-51 CARBON

47K 47K 3.3M

5% 5% 5%

R904 R905

1-249-421-11 CARBON 1-249-421-11 CARBON

2.2K 2.2K

5% 5%

R906

1-249-417-11 CARBON

R906

1-249-418-11 CARBON

R910

1-219-120-11 FUSIBLE

5% 1/4W (US, CND, AEP, UK, KR) 1.2K 5% 1/4W (EXCEPT US, CND, AEP, UK, KR) 0.15 5% 1/4W

< CAPACITOR > C901 C902 C903 C905 C906

1-136-165-00 1-136-165-00 1-136-165-00 1-161-055-00 1-161-055-00

FILM FILM FILM CERAMIC CERAMIC

0.1uF 0.1uF 0.1uF 0.022uF 0.022uF

5% 5% 5% 10% 10%

50V 50V 50V 50V 50V

C907 C908 C909 C910 C911

1-161-055-00 1-161-055-00 1-161-055-00 1-161-055-00 1-161-055-00

CERAMIC CERAMIC CERAMIC CERAMIC CERAMIC

0.022uF 0.022uF 0.022uF 0.022uF 0.022uF

10% 10% 10% 10% 10%

50V 50V 50V 50V 50V

C912 0 C913 C914 C915

1-161-055-00 1-113-925-11 1-126-947-11 1-136-497-81

CERAMIC CERAMIC ELECT FILM

0.022uF 0.01uF 47uF 0.1uF

1/4W 1/4W 1/2W F (US, CND) 1/4W 1/4W

< RELAY > 0 RY901

1-755-276-11 RELAY, POWER < SWITCH >

0 S901

1-571-309-11 SWITCH (VOLTAGE DETECT) (E, E51, EA, SP) < TRANSFORMER >

0 T901

C915

1-136-165-00 FILM

10% 50V 20% 250V 20% 35V 5% 50V (EA, MX, TW) 0.1uF 5% 50V (EXCEPT EA, MX, TW)

1-439-772-11 TRANSFORMER, POWER (EXCEPT US, CND, AEP, UK, KR) 0 T901 1-439-779-11 TRANSFORMER, POWER (AEP, UK, KR) 0 T901 1-439-781-11 TRANSFORMER, POWER (US, CND) ************************************************************ REG BOARD ********* < CAPACITOR >

< CONNECTOR > * CN901 * CN902 * CN902

1-793-660-11 PIN, CONNECTOR (PC BOARD) 3P 1-564-511-11 PLUG, CONNECTOR 8P (EXCEPT EA, MX, TW, KR) 1-564-710-11 PIN, CONNECTOR (SMALL TYPE) 8P (EA, MX, TW, KR) < DIODE >

D906 D907 D908 D909 D910

8-719-991-33 8-719-991-33 8-719-991-33 8-719-991-33 8-719-991-33

DIODE DIODE DIODE DIODE DIODE

C306 C307

1-164-156-11 CERAMIC CHIP 1-164-156-11 CERAMIC CHIP

0.1uF 0.1uF

25V 25V

< IC > IC305 8-759-231-57 IC TA7810S IC306 8-759-450-49 IC BA07T ************************************************************

1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.

Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.

HCD-NE3

Ref. No.

Part No.

Description

Remark

Ref. No.

Part No.

Description

Remark

MISCELLANEOUS ************** 05 05 05 05 05

1-696-570-21 1-775-790-12 1-769-079-23 1-769-744-52 1-783-531-22

CORD, POWER (EA) CORD, POWER (AUS) CORD, POWER (KR) CORD, POWER (AEP, UK, E51, SP) CORD, POWER (US, CND)

05 05 05 6 6

1-829-387-11 1-827-226-11 1-827-597-31 1-693-625-11 1-693-628-11

CORD, POWER (AR) CORD, POWER (E, MX) CORD, POWER (TW) TUNER (FM/AM) (US, CND) TUNER (FM/AM) (E, E51, EA, MX, SP, TW, AR, AUS)

6 10 110 163 0 167

1-693-629-11 1-500-386-11 1-796-352-41 1-827-991-11 8-820-221-01

TUNER (FM/AM) (AEP, UK, KR) FILTER, CLAMP (FERRITE CORE) DECK, MECHANICAL (CMAL5Z220A) WIRE (FLAT TYPE) (16 CORE) OPTICAL PICK-UP KSM-213EDP/C2NP

0 T902 0 T902 0 T902 0 T902 0 T902

1-443-245-11 1-443-244-11 1-443-396-11 1-443-397-11 1-443-246-11

TRANSFORMER, POWER (AEP, UK) TRANSFORMER, POWER (US, CND) TRANSFORMER, POWER (EA) TRANSFORMER, POWER (KR) TRANSFORMER, POWER (E, E51, SP, TW, AR, AUS)

S101 S820

1-771-853-11 SWITCH, DETECTION (LIMIT) 1-692-960-11 SWITCH, PUSH (1KEY) (CD LID OPEN/CLOSE DETECT) ************************************************************ ACCESSORIES ************ 0 0

1-569-008-32 ADAPTOR, CONVERSION (E51, SP) 1-770-019-11 ADAPTOR, CONVERSION PLUG 3P (UK)

The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.

Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.