Manual de serviço tv led lcd lg 42le5500 chassis lt03e by Portal da Eletrônica

Internal Use Only North/Latin America Europe/Africa Asia/Oceania

http://aic.lgservice.com http://eic.lgservice.com http://biz.lgservice.com

LED LCD TV SERVICE MANUAL CHASSIS : LT03E

MODEL : 42LE5500

42LE5500-DA

CAUTION BEFORE SERVICING THE CHASSIS, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

/I P

P/NO : MFL63283601 (1003-REV00)

INPUT

Printed in Korea

CONTENTS

CONTENTS .............................................................................................. 2 SPECIFICATION ....................................................................................... 3 ADJUSTMENT INSTRUCTION ................................................................ 7 EXPLODED VIEW .................................................................................. 17 SVC. SHEET ...............................................................................................

-2-

LGE Internal Use Only

SAFETY PRECAUTIONS IMPORTANT SAFETY NOTICE Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Exploded View. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.

Leakage Current Hot Check (See below Figure) Plug the AC cord directly into the AC outlet.

General Guidance An isolation Transformer should always be used during the servicing of a receiver whose chassis is not isolated from the AC power line. Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal injury from electrical shocks. It will also protect the receiver and it's components from being damaged by accidental shorts of the circuitry that may be inadvertently introduced during the service operation. If any fuse (or Fusible Resistor) in this TV receiver is blown, replace it with the specified. When replacing a high wattage resistor (Oxide Metal Film Resistor, over 1 W), keep the resistor 10 mm away from PCB.

Do not use a line Isolation Transformer during this check. Connect 1.5 K / 10 watt resistor in parallel with a 0.15 uF capacitor between a known good earth ground (Water Pipe, Conduit, etc.) and the exposed metallic parts. Measure the AC voltage across the resistor using AC voltmeter with 1000 ohms/volt or more sensitivity. Reverse plug the AC cord into the AC outlet and repeat AC voltage measurements for each exposed metallic part. Any voltage measured must not exceed 0.75 volt RMS which is corresponds to 0.5 mA. In case any measurement is out of the limits specified, there is possibility of shock hazard and the set must be checked and repaired before it is returned to the customer.

Leakage Current Hot Check circuit Keep wires away from high voltage or high temperature parts.

AC Volt-meter

Before returning the receiver to the customer, always perform an AC leakage current check on the exposed metallic parts of the cabinet, such as antennas, terminals, etc., to be sure the set is safe to operate without damage of electrical shock.

Leakage Current Cold Check(Antenna Cold Check) With the instrument AC plug removed from AC source, connect an electrical jumper across the two AC plug prongs. Place the AC switch in the on position, connect one lead of ohm-meter to the AC plug prongs tied together and touch other ohm-meter lead in turn to each exposed metallic parts such as antenna terminals, phone jacks, etc. If the exposed metallic part has a return path to the chassis, the measured resistance should be between 1 MΩ and 5.2 MΩ. When the exposed metal has no return path to the chassis the reading must be infinite. An other abnormality exists that must be corrected before the receiver is returned to the customer.

-3-

To Instrument’s exposed METALLIC PARTS

0.15 uF

Good Earth Ground such as WATER PIPE, CONDUIT etc.

1.5 Kohm/10W

When 25A is impressed between Earth and 2nd Ground for 1 second, Resistance must be less than 0.1 Ω *Base on Adjustment standard

LGE Internal Use Only

SPECIFICATION NOTE : Specifications and others are subject to change without notice for improvement.

3. Test method

1. Application range This specification is applied to the LCD TV used LT03B/D/E/N/T/S chassis.

2. Requirement for Test

1) Performance: LGE TV test method followed 2) Demanded other specification - Safety : CE, IEC specification - EMC :CE, IEC

Each part is tested as below without special appointment. 1) Temperature: 25 ºC ± 5 ºC(77 ºF ± 9 ºF), CST: 40 ºC ± 5 ºC 2) Relative Humidity : 65 % ± 10 % 3) Power Voltage : Standard input voltage (AC 100-120 V~ 50 / 60 Hz) * Standard Voltage of each products is marked by models. 4) Specification and performance of each parts are followed each drawing and specification by part number in accordance with BOM. 5) The receiver must be operated for about 20 minutes prior to the adjustment.

4. Module General Specification No.

Item

Specification

Remark

Display Screen Device

105 cm(42 inch) wide color display module

Aspect Ratio

16:9

LCD Module

105 cm(42 inch) TFT WUXGA LCD

Operating Environment Temp. : 0 deg ~ 40 deg Humidity : 0 % ~ 85 %

Storage Environment

Temp. : -20 deg ~ 60 deg Humidity : 0 ~ 85 %

Input Voltage

AC 100-240V~, 50 / 60Hz

Power Consumption

FHD, 120Hz(Edge LED)

LC420EUH-SCA1/2 - LE5500, LE7500

=LCD(Module)+Backlight(LED) 8

Module Size

973.2(H) x 566.2(V) x 10.8 mm(D)

LC420EUH-SCA1/2 - LE5500, LE7500

Pixel Pitch

0.4845 (H) x 0.4845 (V)

LC420EUH-SCA1/2 - LE5500, LE7500

Back Light

CCFL/Edge-LED/IOP-LED

Display Colors

1.06 B(true) colors (10-bit)

Coating

3H(Hard coating), Anti-glare

-4-

LGE Internal Use Only

5. Chroma & Brightness No.

Item

Specification

Viewing Angle<CR>10>

Right/Left/Up/Down

Luminance

Luminance (cd/m2)

Contrast Ratio

CIE Color Coordinates

White

Min.

Typ.

Max.

89/89/89/89

LC420EUH-SCA1/2

360

450

LC420EUH-SCA1/2

1000

1400

Variation

1.3

RED

0.279

0.292

Green Blue

Remark

MAX /MIN All white / All black

0.647

Typ.

0.332

Typ.

-0.03

0.309

+0.03

0.601

0.149

0.059

6. Component Video Input (Y, CB/PB, CR/PR) Specification

No. Resolution

Proposed

H-freq(kHz)

V-freq(Hz)

15.73

59.94

Pixel clock(MHz)

720*480

13.500

SDTV, DVD 480I(525I)

720*480

15.75

60.00

13.514

SDTV, DVD 480I(525I)

3. 720*576

15.625

50.00

13.500

SDTV, DVD 576I(625I) 50Hz

720*480

31.47

59.94

27.000

SDTV 480P

720*480

31.50

60.00

27.027

SDTV 480P

720*576

31.25

50.00

27.000

SDTV 576P 50Hz

1280*720

44.96

59.94

74.176

HDTV 720P

1280*720

45.00

60.00

74.250

HDTV 720P

1280*720

37.50

50.00

74.25

HDTV 720P 50Hz

10.

1920*1080

28.125

50.00

74.250

HDTV 1080I 50Hz,

11.

1920*1080

33.72

59.94

74.176

HDTV 1080I

12.

1920*1080

33.75

60.00

74.25

HDTV 1080I

13.

1920*1080

56.25

148.5

HDTV 1080P

14.

14 1920*1080

67.432

59.94

148.350

HDTV 1080P

15.

1920*1080

67.5

60.00

148.5

HDTV 1080P

7. RGB (PC) Specification

No. Resolution

H-freq(kHz)

V-freq(Hz)

Proposed

Remarks

Pixel Clock(MHz)

640*350

31.468

70.09

25.17

EGA

720*400

31.469

70.09

28.32

DOS

640*480

31.469

59.94

25.17

VESA(VGA)

800*600

37.879

60.317

VESA(SVGA)

1024*768

48.363

60.004

VESA(XGA)

1280*768

47.776

59.87

79.5

VESA(WXGA)

1360*768

47.72

59.799

84.75

VESA(WXGA)

1280*1024

63.668

59.895

109.00

SXGA

Only FHD model

1920*1080

66.587

59.934

138.50

WUXGA (Reduced Blanking)

Only FHD model

-5-

LGE Internal Use Only

8. HDMI Input (1) DTV Mode No.

Resolution

H-freq(kHz)

V-freq.(Hz)

Pixel clock(MHz)

Proposed

720*480

15.73

59.94

13.500

SDTV, DVD 480I(525I)

720*480

15.75

60.00

13.514

SDTV, DVD 480I(525I)

720*576

15.625

50.00

13.500

SDTV, DVD 576I(625I) 50Hz

720*480

31.47

59.94

SDTV 480P

720*480

31.5

60.00

27.027

SDTV 480P

720*576

31.25

50.00

SDTV 576P

1280*720

44.96

59.94

74.176

HDTV 720P

1280*720

60.00

74.25

HDTV 720P

1280*720

37.5

50.00

74.25

HDTV 720P

10.

1920*1080

28.125

50.00

74.25

HDTV 1080I

11.

1920*1080

33.72

59.94

74.176

HDTV 1080I

12.

1920*1080

33.75

60.00

74.25

HDTV 1080I

13.

1920*1080

56.25

50.00

148.5

HDTV 1080P

14.

1920*1080

67.432

59.94

148.350

HDTV 1080P

15.

1920*1080

67.5

60.00

148.5

HDTV 1080P

16.

1920*1080

24.00

74.25

HDTV 1080P

17.

1920*1080

33.75

30.00

74.25

HDTV 1080P

Remark Spec. out but display.

(2) PC Mode No.

V-freq.(Hz)

Pixel clock(MHz)

640 480

Resolution

31.469

H-freq(kHz)

59.94

25.17

VESA(VGA)

Proposed

800 600

37.879

60.317

40.00

VESA(SVGA)

1024 768

48.363

60.004

65.00

VESA(XGA)

1280 768

47.776

59.87

79.5

VESA(WXGA)

1360 768

47.72

59.799

84.62

VESA(WXGA)

1280 1024

63.595

60.00

108.875

SXGA

1920 1080

66.647

59.988

138.625

WUXGA

-6-

Remark

LGE Internal Use Only

ADJUSTMENT INSTRUCTION 1. Application Range

4. PCB assembly adjustment method

This specification sheet is applied to all of the LCD TV with LT03B/D/E/H/R/S chassis.

4.1. MAC Address Download & LAN test 4.1.1. MAC Address D/L A

2. Designation (1) Because this is not a hot chassis, it is not necessary to use an isolation transformer. However, the use of isolation transformer will help protect test instrument. (2) Adjustment must be done in the correct order. (3) The adjustment must be performed in the circumstance of 25 ºC ± 5 ºC of temperature and 65 % ±10 % of relative humidity if there is no specific designation. (4) The input voltage of the receiver must keep AC 100-240 V~ 50 / 60Hz. (5) Before adjustment, execute Heat-Run for 5 minutes at RF no signal.

D/L Program : Serial.exe

4.1.1.1. Method 1) Connect Jig to PCBA.

1) Execute “ Serial.exe” on PC, MAC Address edit : Start / End MAC address input 2) Connect Com-port.(Port connection button click) 3) Load button click(3) for MAC Address write 4) MAC address Write.

3. Adjustment items 3.1. PCB assembly adjustment items 1) Mac Address D/L & LAN Test 2) Main S/W program download : Using USB Memory stick 3) Input Tool - Option 4) Download EDID : EDID data are automatically downloaded when adjusting the Tool Option. 5) ADC Calibration – RGB & Component 6) Check SW Version

3.2. SET assembly adjustment items 1) Input Area option. 2) Adjustment of White Balance : Auto 3) Adjustment of White Balance : Manual 4) Intelligent Sensor Inspection Guide 5) Blue-Tooth Inspection Guide 6) Local Dimming Inspection Guide 7) Preset CH information 8) Internal Press Test 9) Motion Remote controller Inspection 10) 3D Function test 11) Outgoing Condition Configuration 12) Sound spec 13) Factoring Option Data input.

5) Check the OK Or NG

-7-

LGE Internal Use Only

4.1.2. PING Test(LAN Operating Test)

4.2. Main S/W program download

4.1.2.1. Check PCBA 1) Connect LAN to PCBA& Power On. 2) Push ADJ key on Adjust remote-controller. 3) Enter “13. ACAP PING TEST” & check Network.

4.2.1. Using the Memory Stick ** USB DOWNLOAD : Service Mode 1) Insert the USB memory Stick to the USB port 2) Automatically detect the SW Version. -> S/W download process is executed automatically. 3) Show the message “Copy the file from the Memory”

4.1.2.2. Check Set 1) Connect TV-Set & PC with Cross LAN cable.(PC IP : 12.12.2.3) 2) Execute “PINT Test program”, Check setting data of program. (TV-Set IP : 12.12.2.2) 3) Push Power Only key on Adjust remote-controlle. 4) Click “RUN”, Check “OK” or “NG”

4) If the TV IS Turn On, Check the updated SW Version and Tool Option.

4.3. Input tool option. Adjust tool option refer to the BOM. A Tool Option Input : PCBA Check Process A Area Option Input : Set Assembly Process *** Tool Option table 55LE5500

47LE5500

42LE5500

32LE5500

Tool Option1

MODEL

45312

33024

24832

16640

Tool Option2

32279

Tool Option3

64556

Tool Option4

25004

24876

Tool Option5

1851

55LE7500

47LE7500

42LE7500

32LE7500

Tool Option1

45344

33056

24864

16672

Tool Option2

32279

Tool Option3

64556

Tool Option4

25004

24876

MODEL

Tool Option5

1851

55LE8500

47LE8500

42LE8500

32LE8500

Tool Option1

45376

33088

24896

16704

Tool Option2

32279

Tool Option3

64572

Tool Option4

25004

24876

Tool Option5

1851

55LX6500

47LX6500

42LX6500

Tool Option2

32279

Tool Option3

64572

Tool Option4

25004

Tool Option5

1979

MODEL

MODEL Tool Option1

-8-

LGE Internal Use Only

After Input Tool Option and AC off Before PCBA check, you have to change the Tool option and have to AC off/on (Plug out and in) (If missing this process, set can operate abnormally)

4.4.4. EDID data 4.4.4.1. LT03B/D/E M0DEL ** Analog(RGB): 128bytes 0

4.3.1. Profile : Must be changed the option value because being different with some setting value depend on module maker, inch and market

4.3.2. Equipment : adjustment remote control.

4.3.3. Adjustment method

4.4. EDID D/L method Recommend that don’t connect HDMI and RGB(D-SUB) cable when downloading the EDID. If not possible, recommend that connect the MSPG equipment. There are two methods of downloading the edid data

4.4.1. 1st Method

4.4.2. 2nd Method Caution : Must be checked that the tool option is right or not. If tool option is wrong, hdmi edid data could not be downloaded well. 1) Press the ADJ key 2) Move to the 10. EDID D/L and Press the right direction key(G) 3) Press the right direction key(G) at Start. 4) After about a few seconds, appear “Waiting..” => “OK”, then compele.

4.4.3. RS-232C command Method 1) Command : AE 00 10 Caution : Don’t connect HDMI and RGB(D-SUB) cable when downloading the EDID. If the cables are connected, Downloading of edid could be failed.

-9-

** HDMI 1 : 256Bytes 0 1 2

** HDMI 2 : 256Bytes 0 1 2

9E 5A

** HDMI 3 : 256Bytes 0 1 2

EDID datas are automatically downloaded when adjusting the Tool Options. Automatically downloaded when pushing the enter key after adjusting the tool option5. It takes about 2seconds.

- The input methods are same as other chassis.(Use ADJ Key on the Adjust Remocon.) (If not changed the option, the input menu can differ the model spec.) Refer to Job Expression of each main chassis ass’y (EBTxxxxxxxx) for Option value Caution : Don’t Press “IN-STOP” key after completing the function inspection.

0 10

00 8

9E 5A

** HDMI 4 : 256Bytes 0 1 2

26 01

00 00

10 30

LGE Internal Use Only

4.4.4.2. LT03R/S/N M0DEL(3D model)

4.5. ADC Calibration : Comp 480i/Comp 1080p/RGB

** Analog(RGB): 128bytes 1

** HDMI 1 : 256Bytes 0 1 2 0

38 B0

** HDMI 3 : 256Bytes 0 1 2

C9 F

** HDMI 4 : 256Bytes 0 1 2

26 01

10 30

4.5.2.1. Process 1) Connect Component/RGB, and RS-232C cable. 2) Command : aa 00 00 [Enter ADC adj. mode](Automatically done) aa 00 00 [Enter ADC adj. mode] xb 00 04 [Change input source to Component1 (480i&1080p)] ad 00 10 [Adjust 480i&1080p Comp1] xb 00 06 [Change input source to RGB(1920x1080)] ad 00 10 [Adjust 1920x1080 RGB] aa 00 90 End adj.

• Required Equipments A Jig (RS-232C protocol) A MSPG-925F/MSPG-1025/MSPG-3233 Pattern Generator A RS-232C cable

4.5.2. ADC Calibration – Using RS-232C

3) Press ADJ key on R/C for adjustment. 4) Enter Password number. Password is “0 0 0 0”. 5) Move to the “6. ADC calibration” by using D/E(CH +/-) and press ENTER(G). 6) Press the right direction key(G) at Start. 7) Press the enter key on “Start” 8) After about a few seconds, appear “Waiting..” => “OK”, then complete. 9) Change input source component 1080p and Do 3)~8) steps. 10) Change input source RGB 1080p and Do 3)~8) steps.

(MSPG-925F Model: 209 / Pattern: 65 )

4.5.1.1. Process 1) Change the Input to Component1 or 2 mode.. 2) Input the Component 480i@60Hz 100% Color Bar YPbPr signal into Component1 or 2.

01 26

01 99

01 4C

** HDMI 2 : 256Bytes 0 1 2

• Required Equipments A Remote controller for adjustment A MSPG-925F/MSPG-1025/MSPG-3233 Pattern Generator

4.5.1. ADC Calibration - Manual

- 10 -

LGE Internal Use Only

4.6. Check SW Version

5.2. Adjustment of White Balance : (For Automatic Adjustment)

4.6.1. Method 1) Push In-star key on Adjust remote-controller. 2) SW Version check

A A

IN START Model Name : Global-Plat

1.Adjust Check

Serial Number : SKJY1107

Adjust Check

¢”

2.ADC Date

1. Country Group(Press OK to Save)

S/W Version

: 00.00.06.01

3.Power Off Status

Country Group Code

MICOM Version

: 2.00.2

4.System

Country Group

BOOT Version

: 1.01.01

5.Model Number D/L

URSA Version

: 1.00

6.Test Option

IR LED Version

: ff

7.External ADC

Tool Option1

EDID Version(RGB)

: 0.01

8.Bluetooth Test

Tool Option2

EDID Version(HDMI)

: 0.02

9.Bluetooth AV CODEC Config

Tool Option3

Maker

: 99

10.Spread Spectrum

Tool Option4

BT S/W Version

: 1.21

11.Sync Level

BT H/W Version

: 4384

12.Wireless Ready

3. Adjust White Balance :

Wireless Host Version

: 0.00.0

13.Stable Count

4. Adjust ADC :

Wireless B/B Version

: 0.00.0

Country

Purpose : Adjust the color temperature to reduce the deviation of the module color temperature. Principle : To adjust the white balance without the saturation, Fix the one of R/G/B gain to 192 (default data) and decrease the others. Adjustment mode : Three modes – Cool / Medium / Warm

A-CAS -

* Required Equipment A Remote controller for adjustment A Color Analyzer : CA100+ or CA-210 or same product (should be used in the calibrated ch by CS-1000) • LCD TV : CH-9 • PDP TV : CH-10 • White LED TV : CH-14 • RGB LED(MNT) : CH-16 A Auto W/B adjustment instrument(only for Auto adjustment)

2. Tool Option

16672

Tool Option5

480i Component

MAC Address : FF:FF:FF:FF:FF:FF

1080p Component

UTT : 9

RGB

UI Res. Version : 1.06

5.EDID :

APP History Ver. : xxxxx

RGB

OK(0x1C)

HDMI1

OK(0xD6,0xF9)

HDMI2

OK(0xD6,0xF9)

HDMI3

OK(0xD6,0xF9)

HDMI4

OK(0xD6,0xF9)

5.2.1. Adjustment of White Balance : (For Automatic Adjustment) Connecting diagram of equipment for measuring (For Automatic Adjustment) Co lo r Analyzer

5. SET assembly adjustment method

RS -232C

Probe

Co m p ut er RS -232C

5.1. Input Area-Option

RS -232C

Pat t ern Generat o r Signal Source

5.1.1. Profile : Must be changed the Area option value because being different of each Country’s Language and signal Condition. 5.1.2. Equipment : adjustment remote control. 5.1.3. Adjustment method - The input methods are same as other chassis.(Use INSTART Key on the Adjust Remocon.) Refer to Job Expression of each main chassis ass’y (EBTxxxxxxxx) for Option value.

* If TV internal pattern is used, not needed

1) Set TV in adj. mode using POWER ON key 2) Zero calibrate probe then place it on the center of the Display 3) Connect Cable(RS-232C) 4) Select mode in adj. Program and begin adj. 5) When adj. is complete (OK Sing), check adj. status pre mode(Warm, Medium, Cool) 6) Remove probe and RS-232C cable to complete adj. • W/B Adj. must begin as start command “wb 00 00” , and finish as end command “wb 00 ff”, and Adj. offset if need * Luminance min value is 150cd in the Cool/Medium/Warm mode( For LCD)

- 11 -

LGE Internal Use Only

5.3. Adjustment of White Balance (for Manual adjustment)

5.4. Intelligent Sensor Inspection Guide

Color analyzer(CA100+, CA210) should be used in the calibrated ch by CS-1000 A Operate the zero-calibration of the CA100+ or CA-210, then stick sensor to the modul adjusting. A For manual adjustment, it is also possible by the following sequence. 1) Select white pattern of heat-run by pressing “POWER ON” key on remote control for adjustment then operate heat run longer than 15 minutes. (If not executed this step, the condition for W/B may be different.) 2) Push “Exit” key. 3) Change to the AV mode by remote control. 4) Input external pattern (85% white pattern) 5) Push the ADJ key -> Enter “0000” (Password) 6) Select “3. W/B ADJUST” 7) Enter the W/B ADJUST Mode 8) Stick the sensor to the center of the screen and select each items (Red/Green/Blue Gain and Offset) using D/E (CH +/-) key on R/C. 9) Adjust R/ G/ B Gain using F/G(VOL +/-) key on R/C. 10) Adjust three modes all (Cool / Medium / Warm) : Fix the one of R/G/B gain and change the others 11) When adjustment is completed, Enter “COPY ALL” 12) Exit adjustment mode using EXIT key on R/C. A

Step 1. Turn on the TV set. Step 2. Press “EYE” button on the Adjustment remote controller.

Step 3. Block the Intelligent Sensor module on the front C/A about 6 seconds. When the “Sensor Data” is lower than 20, you can see the “OK” message => If it doesn’t show “OK” message, the Sensor Module is defected one. You have to replace that with a good one.

1 CASE First adjust the coordinate far away from the target value(x, y).

1. x, y > target i) Decrease the R, G. 2. x, y < target i) First decrease the B gain, ii) Decrease the one of the others. 3. x > target , y < target i) First decrease B, so make y a little more than the target. ii) Adjust x value by decreasing the R 4. x < target , y > target i) First decrease B, so make x a little more than the target. ii) Adjust x value by decreasing the G

Step 4. After check the “OK” message come out, take out your hand from the Sensor module. => Check “Sensor Data” value change from “0” to “300” or not. If it doesn’t change the value, the sensor is also defected one. You have to replace it.

- 12 -

LGE Internal Use Only

5.5. Blue-Tooth Inspection Guide

5.7. Preset CH information

5.5.1. Test Condition.

5.7.1. Analog CH Table_Ver_1_0

Must located another set in a state of DC ON (without checking set) in closer distance(5M). -On total assembly step, S/W deal with connection (between Set and another Set, other device that be compatible with Bluetooth)

5.5.2. Need device : same set in closer distance, adjustment remote control

Storage

Band

CH Name

Freq(Mhz)

Factory

PAL

System

V/UHF

NZ01

C 01

45.25

Freq/50Khz

905

SECAM

V/UHF

R34

C 34

575.25

11505

V/UHF

PAL

NTSC

PAL

7 8

Initial CH

(Gumi)

EU05

C 05

175.25

3505

Cable

PI11

S 11

231.25

4625

V/UHF

BR48

V/UHF

E04

C 04

62.25

1245

PAL

V/UHF

EU07

C 07

189.25

3785

PAL

675.25

V/UHF

EU50

703.25

14065

PAL

V/UHF

EU52

C 52

719.25

14385

PAL

V/UHF

PI41

C 41

C 50

631.25

12625

PAL

V/UHF

PI63

C 63

807.25

16145

5.5.3. Method

PAL

Cable

S 47

102.25

2045

PAL

V/UHF

C 21

471.25

9425

1) Push “Power on key” on adjustment remote control. change “Bluetooth On” mode 2) Push “EXIT” KEY 3) Push ”B-TOOTH”(NEW) or “PIP”(OLD) Key 4) Check “Searching OK” message 5) Push “Exit” key, finish check.

SECAM

V/UHF

SLB

C 02

55.75

SECAM

Cable

CATVE

S 07

152.75

3055

SECAM

V/UHF

SL36

C 36

591.25

11825

1115

17 18

PAL

V/UHF

C 05

175.25

3505

PAL

V/UHF

E51

C 51

711.25

14225 12625

PAL

V/UHF

I41

C 41

631.25

SECAM

V/UHF

C 05

93.25

PAL

V/UHF

C 04

62.25

1245

PAL

V/UHF

E31

C 31

551.25

11025

PAL

V/UHF

I21

C 21

471.25

9425

(WR)

1865

PAL

V/UHF

I69

C 69

855.25

17105

PAL

V/UHF

E48

C 48

687.25

13745

SECAM

V/UHF

C 08

200.00

4000

SECAM

V/UHF

L45

C 45

663.25

13265

PAL

V/UHF

E25

C 25

503.25

10065

SECAM

V/UHF

C 07

183.25

3665

SECAM

V/UHF

C 07

189.25

32 33 34

NTSC

US-4

C 04

NTSC

V/UHF

J-01

C 01

91.25

1825

NTSC

V/UHF

US-13(J-11)

C 13

211.25

4225

V/UHF

67.25

1345

NTSC

V/UHF

US-14(J-13)

C 14

471.25

9425

NTSC

V/UHF

US-63(J62)

C 63

765.25

15305

NTSC

Cable

CATV-15

S 15

127.25

2545

497(Center Freq)

NTSC

V/UHF

US-18(Digital)

C 18

SECAM

D/K

V/UHF

R-1(CIS)

C 01

49.75

995

PAL

D/K

V/UHF

D-10(China10)

C 10

200.25

4005

PAL

D/K

V/UHF

K-36

C 36

695.25

13905

PAL

B/G

V/UHF

E-5

C 05

175.25

3505

PAL

B/G

V/UHF

G-40

C 40

623.25

12465

PAL

V/UHF

I-28

C 28

527.25

10545

5.6. Local Dimming Inspection (Optional)

48 49

5.6.1. Edge LED models with local dimming

D/K

V/UHF

D-1

C 01

49.75

995

PAL

D/K

V/UHF

D-4

C 04

77.25

1545

PAL

D/K

V/UHF

D-10

C 10

200.25

4005 3505

52 53

1) Press ‘TILT” key of the Adj. R/C and check moving patterns. The black bar patterns moves from left to right. If local dimming function does not work, a whole screen shows full white.

PAL

NT_ PANDA

PAL

B/G

V/UHF

E-5

C 05

175.25

SECAM

D/K

V/UHF

R-12

C 12

223.25

4465

NTSC

V/UHF

US-14

C 14

471.25

9425

SECAM

D/K

V/UHF

R-34

C 34

575.25

11505

PAL

V/UHF

I-41

C 41

631.25

12625

NTSC

V/UHF

US-63

C 63

765.25

15305

58 59

SECAM

B/G

V/UHF

E-04

62.25

1245

SECAM

D/K

V/UHF

R-05

C 05

93.25

1865

PAL

B/G

V/UHF

E-05

C 05

175.25

3505 4465

C 04

SECAM

D/K

V/UHF

R-12

C 12

223.25

PAL

B/G

V/UHF

E-21

C 21

471.25

9425

SECAM

D/K

V/UHF

R-34

C 34

575.25

11505

SECAM

D/K

V/UHF

R-54

C 54

735.25

14705

66 67 68

PAL

B/G

V/UHF

E-2

C 02

48.25

965

PAL

B/G

V/UHF

E-5

C 05

175.25

3505

PAL

B/G

V/UHF

E-11

C 11

217.25

4345

PAL

B/G

V/UHF

E-25

503.25

10065

PAL

B/G

V/UHF

E-36

C 36

591.25

11825

PAL

V/UHF

I-30

C 30

543.25

10865

PAL

Cable

I-11

S 11

231.25

4625

SECAM

D/K

Cable

R-05

S 45

93.25

1865

SECAM

11505

5.6.2. IOP LED models with local dimming

1) Press ‘TILT” key of the Adj. R/C and check moving patterns. The black cross-bar patterns moves from top-left to Bottomright. If local dimming function does not work, a whole screen shows full white.

C 25

D/K

V/UHF

R-34

C 34

575.25

SECAM

V/UHF

F-B

C 47

55.75

NTSC

V/UHF

US-04

67.25

1345

PAL

V/UHF

N-10

C 10

193.25

3865

NTSC

V/UHF

US-11

C 11

199.25

3985

NTSC

V/UHF

US-13

C 13

211.25

4225

NTSC

V/UHF

US-30

C 30

567.25

11345

SECAM

77 IN

1115

V/UHF

F-49

C 49

695.25

13905

PAL

V/UHF

M-69

C 69

801.25

16025

JAPAN

Cable

JA-01

S-95

91.25

JAPAN

V/UHF

JA-04

171.25

3425

JAPAN

V/UHF

JA-36

609.3

12186

PAL

B/G

Cable

Au-5

S-47

102.25

2045

1825

89 90 91

- 13 -

PAL

B/G

V/UHF

E-05

C 05

175.25

3505

NTSC

V/UHF

US-13

C 13

211.25

4225

SECAM

D/K

V/UHF

R-12

C 12

223.25

PAL

D/K

V/UHF

D-01

C 01

49.75

995

SECAM

D/K

V/UHF

R-34

C 34

575.25

11505

PAL

B/G

V/UHF

E-21

C 21

471.25

9425

PAL

D/K

V/UHF

D-04

C 04

77.25

1545

4465

LGE Internal Use Only

5.7.2. Preset CH write condition

5.10. 3D Function test

1) AC on time on only one after assembled automatically 2) In case of PAL model, CH recover on SVC OSD manually In case of NTSC model, default channel : -> After In-Stop / Facotry reset TV : 2,3,4,5,6,7,8,9,10,11,12,13,14,30,51,55,63 CATV : 15,16,17,55,95

5.10.1. Equipment : Pattern Generator MSPG3233, HDMI mode 37, pattern No. 81 5.9.2. Process 1) Connect HDMI (HDMI mode 371, Pattern No. 81)

5.7.3. Preset CH erase condition 1) In-Stop key

5.8. Internal press test No

Item

1. Dielectric Voltage(AC<->FG)

Vallue

Unit

1.5

1.5 2. Dielectric Voltage(Without FG)

3 3

Remark At 100mA for 1sec(Line) At 100mA for 1min(OQC)

At 100mA for 1sec(Line) At 100mA for 1min(OQC)

2) Insert 3D Mode, Select side by side mode. 3) Without 3D-glasses, Like below figure.

5.9. Motion Remote controller Inspection 5.9.1. Equipment : Motion remote controller for test, IR-KEY-CODE remote controller for test Check battery before test. (Recommend : Change battery for every Lot.) 5.9.2. Process 1) Push “Mute” or “ START” key for pairing between TV-set and motion remote controller. 2) Push “OK” or “Enter” key, you can see the Cursor on screen. 3) Push “Vol+” or “STOP” key, Disconnect Pairing.

4) With 3D left-glass, Like below figure. (Center is RED)

5) With 3Dright-glass, Like below figure.(Center is Blue)

- 14 -

LGE Internal Use Only

** Appendix ** D. Bluetooth S/W Upgrade by using USB drive Input

3. USB input Automatically loading menu

1. Preparation Equipment a. USB Memory Stick

b. New Bluetooth Software

* The OSD “USB Device loading” is appealed by automatically…. 4. Selecting Window for Bluetooth Software update

c. Copy New File Copy Bluetooth software MCL389x.bin file to memory stick with out folder. *Caution : Do no t copy the file to the inside folder

• The Pop-up window appears for selecting to update Bluetooth software and information about current Bluetooth software. (Ex : V2.02) • Select “Yes”

2. Connection Plug-in USB Memory stick to the USB input of the set.

- 15 -

LGE Internal Use Only

5. Bluetooth S/W Downloading Process

• Time Process Downloading new Bluetooth software about 10seconds • Please Wait until finish and do not un-plug power cable 6. OSD – Bluetooth software updated successfully

• OSD Information Bluetooth software update success • LCDTV Set will restart by automatically… • Time Process to restart about 5seconds 7. Check S/W Version • Push “ IN-START” button on service remote Controller • Check Information Bluetooth S/W version will appear on OSD Service Menu. Example : Bluetooth SW version 2.05

- 16 -

LGE Internal Use Only

EXPLODED VIEW IMPORTANT SAFETY NOTICE

900

910

840

880

500

300

120

A21

200

A10

800

LV1

530

LV2

540

820

521

830

400

920

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and EXPLODED VIEW. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.

- 17 -

LGE Internal Use Only

EXT IRQ GPIO_00, GPIO_01, GPIO_02, GPIO_11, GPIO_11, GPIO_39

J25

CI_A[6]

F26

CI_A[8]

H28

CI_A[9]

J26

CI_A[13]

H27

CI_A[12]

G26

CI_A[11]

J27

CI_A[10]

J28

CI_A[7] 22 R116

F27

H26

G24

R122 R117

G27

EBI_CS

4.7K

K23

G25 R140

R193

R194

From wireless_I2C to micom I2C

+3.3V_NORMAL

G28

22 R127

EBI_ADDR2

GPIO_02

EBI_ADDR1

GPIO_03

EBI_ADDR0

GPIO_04

EBI_ADDR5

GPIO_05

EBI_ADDR6

GPIO_06

EBI_ADDR8

GPIO_07

EBI_ADDR9

GPIO_08

EBI_ADDR13

GPIO_09

EBI_ADDR12

GPIO_10

EBI_ADDR11

GPIO_11

EBI_ADDR10

GPIO_12

EBI_ADDR7

GPIO_13

EBI_TAB

GPIO_14

EBI_WE1B

GPIO_15

EBI_CLK_IN

GPIO_16

EBI_CLK_OUT

GPIO_17

EBI_RWB

GPIO_18

EBI_CS0B

GPIO_19

NAND_DATA[0]

U24

NAND_DATA[1]

T26

NAND_DATA[2]

T27

NAND_DATA[3]

U26

NAND_DATA[4]

U27

NAND_DATA[5]

V26

NAND_DATA[6]

V27

NAND_DATA[7]

V28

NAND_CEb

T24

NAND_ALE

R23

NAND_REb

T23

NAND_CLE

T25

NAND_WEb

R24

NAND_RBb

U25

GPIO_23

NAND_DATA2

GPIO_24

NAND_DATA3

GPIO_25

NAND_DATA4

GPIO_26

NAND_DATA5

GPIO_27

NAND_DATA6

GPIO_28

NAND_DATA7

GPIO_29

NAND_CS0B

GPIO_30

NAND_ALE

GPIO_31

NAND_REB

GPIO_32

NAND_CLE

GPIO_33

NAND_WEB

GPIO_34

NAND_RBB

GPIO_35

A8â&#x20AC;&#x2122;h

OPT

10K R173

SF_MOSI

GPIO_39

SF_SCK

GPIO_40

SF_CSB

GPIO_41

AA28

R1026

R1028

C171 8pF OPT

C167 8pF OPT

* I2C MAP

N27

AD19

0 WIRELESS

* I2C_1 :

* I2C_2 :

WIRELESS

Y28 Y27

BCM_AVC_DEBUG_RX1

BB Add.

EPHY_ACTIVITY EPHY_LINK M_REMOTE_TX

R107

100

R108

100

L24

DTV_ATV_SELECT 5V_HDMI_2

P25

R1033

R1046

R115

1.8K For CI

AV_CVBS_DET

R1044

C173 22uF 16V

M_REMOTE_TX 17page : Motion Remocon M_REMOTE_RX 17page : Motion Remocon

M_REMOTE_RX VREG_CTRL TUNER_RESET

EMI C180 100pF 50V

For CI

/CI_CD1

CI_OUTCLK /CI_CD2 /CI_IREQ MODEL_OPT_6

K4 K1

MODEL_OPT_3

L27

WIRELESS_DL_RX

M26 N23

R132

R28

R1050

100

R27

R161

R26

R133

WIRELESS_DL_TX FE_TS_VAL_ERR

External Demod.

5V_HDMI_3

100 22

5V_HDMI_4 MODEL_OPT_2 SCART1_DET

P28 P27

SIDE_COMP_DET R103 22

0 R129

100 22

R102

K6 K5 P26

RF_SWITCH_CTL_CHB RGB_DDC_SCL

R160

FRC_RESET

15page : CHB_SUB_TUNER +3.3V_NORMAL

RGB_DDC_SDA NON_EU COMP2_DET

22 R1051 LOCAL DIMMING

SIDE_COMP_DET RF_SWITCH_CTL_CHB

R1052 +3.3V_NORMAL R187-*1 R184-*1 4.7K 2.2K 2.2K

R1049

LG5111_RESET HP_DET

LG5111_RESET

W27

NON_EU

EU SCL0_3.3V

W28

SGPIO_01

SDA0_3.3V

W26

SGPIO_02

SCL1_3.3V

W25

SGPIO_03

SDA1_3.3V

SGPIO_04

SCL2_3.3V

SGPIO_05

SDA2_3.3V

SGPIO_06

SCL3_3.3V

SDA3_3.3V

SGPIO_07

* NAND FLASH MEMORY 4Gbit (512M for BB)

Boot Strap

100

GPIO_57

* I2C_3 :

100

R110

SGPIO_00 R124

R109

BCM_AVC_DEBUG_TX1

A_DIM

R1041

5V_HDMI_1

L23

GPIO_56 R123

12K HDMI_HPD_1 IR_IN

100

R1048

17page : Motion Remocon 56 AUD_MASTER_CLK

R105

HDMI_HPD_2 IR_IN

R106

AE19

DD 1K

R199

M23

GPIO_55

* I2C_0 :

MODEL_OPT_0

P23

GPIO_54

OPT

CI_MOD_RESET

BT_MUTE

AH18

GPIO_53

SCL2_3.3V

R111

N28

GPIO_52

WIRELESS_SCL

SC_RE2

R25

GPIO_51

Q104 FDV301N

BCM_RX BCM_TX SC_RE1

AA25

GPIO_49

OPT

+3.3V_NORMAL

BT_RESET /RST_HUB

M27

GPIO_48

SDA2_3.3V

2.7K

Y26

GPIO_50

WIRELESS_SDA

R1053

MODEL_OPT_1

Y25

GPIO_47 Q103 FDV301N

DEMOD_RESET

DSUB_DET

GPIO_46

SDA3_3.3V

28page : ISDB Demod

DEMOD_RESET PWM_DIM HDMI_HPD_3

GPIO_45 SCL3_3.3V

R1029

For CI

HDMI_HPD_4

R113 R1042 22

GPIO_44

SDA

R114

AA26

GPIO_43

SCL

CI_5V_CTL

1K K25 DEMOD_RESET 22 AA27

GPIO_42

MODEL_OPT_5

K26

VCC

V24

GPIO_38

VSS

V23

U23

4.7K

R1025

R1032 0

C103 0.1uF

IC102 M24M01-HRMN6TP

SF_MISO

PWM0 : GPIO_24 PWM1 : GPIO_09

17page : Motion Remocon

SIDE_AV_DET

K24

GPIO_37

W24

INTERRUPT PIN INTERRUPT PIN INTERRUPT PIN

MODEL_OPT_4

K28

GPIO_36

+3.3V_NORMAL

ERROR_OUT

K27

GPIO_22

NAND_DATA1

POWER_DET DC

R192

L25

GPIO_21 NAND_DATA0

N25

GPIO_20

GPIO_23 GPIO_25 GPIO_29 GPIO_26

OPT R1047

L26

1.2K R171

H23

CI_A[5]

GPIO_01

1.2K R176

CI_A[0]

GPIO_00

EBI_ADDR4

1.2K R177

H24

N26 EBI_ADDR3

1.2K R180

GAS7-*2

MDS62110205

GAS6-*2

7.5T_GAS

MDS62110205

7.5T_GAS

EBI_RW

NAND_DATA[0-7] +3.3V_NORMAL

NVRAM +3.3V_NORMAL

CI_A[1]

33 GAS2-*2

7.5T_GAS

MDS62110205

GAS1-*2

7.5T_GAS

MDS62110205

/CI_WAIT EBI_WE

H25

1.2K R183

EBI_CS

J24

1.2K R184

GAS7-*1

5.5T_GAS

MDS62110204

GAS6-*1

MDS62110204

5.5T_GAS

R1045 4.7K

J23

CI_A[4] CI_A[2]

1.2K R187

+3.3V_NORMAL

CI_A[3]

: : : :

1.2K R170

GAS9

GAS8

MDS62110206 OPT

GAS7

MDS62110206 OPT

GAS6

6.5T_GAS

MDS62110206

GAS5

6.5T_GAS

MDS62110206

GAS4

OPT

GAS3

MDS62110206

GAS2-*1

5.5T_GAS

MDS62110204

SYS_RESETb

GAS1-*1

5.5T_GAS

MDS62110204

R1030

SOC_RESET

IR_INT IR1_IN IR2_IN IR_OUT

IC100 LGE3556C (C0 VERSION) CI_A[0-13]

R1027 10K

+3.3V_NORMAL

OPT

GAS2

MDS62110206 OPT

GAS1

6.5T_GAS

MDS62110206

6.5T_GAS

RESET

MDS62110206

SMD GASKET

Default Res. of all NAND pin is Pull-down +3.3V_NORMAL

+3.3V_NORMAL

2.7K

NAND_DATA[1]

NC_10 CL

NAND_CLE NAND_IO[1] : NAND Block 0 Write (DNS) 0 : Enable Block 0 Write 1 : Disable Block 0 Write

NAND_ALE

NAND_WEb NAND_IO[3:2] : NAND ECC (1, DNS) 00 : No ECC 01 : 1 ECC Bit 10 : 4 ECC Bit 11 : 8 ECC Bit

+3.3V_NORMAL

4.7K

R136

NC_11 NC_12

NAND_IO[4] : CPU Endian (0) 0 : Little Endian 1 : Big Endian

NC_13 NC_14

C NAND_IO[6:5] : Xtal Bias Control (1, DNS) 00 : 1.2mA (Fundmental Recommand) 01 : 1.8mA 10 : 2.4mA (3rd over tune Recommand) 11 : 3.0mA

FLASH_WP

Q101 KRC103S

NC_15

NC_25 NC_24 +3.3V_NORMAL NC_23

C136

10uF 10V

VDD_2 VSS_2

C115 0.1uF

NC_22 NC_21

IF_AGC_SEL LNA2_CTL/BOSTER_CTL RF_SWITCH_CTL BT_ON/OFF

NC_20 NAND_DATA[3]

I/O2

NAND_DATA[2]

I/O1

NAND_DATA[1]

I/O0

NAND_DATA[0]

NC_19 NC_18 NC_17

R1012

100

R1019

100

R1024

100

MODEL_OPT_0

N28

LOW

HIGH URSA3

NON_URSA3

/CI_SEL

R130

MODEL_OPT_1

AA26

MAIN_MINI_LVDS

MAIN_LVDS

MODEL_OPT_2

R26

DDR-256M

DDR-512M

MODEL_OPT_3

FHD

MODEL_OPT_4

L25

FRC

MODEL_OPT_5

K27

GIP

NON-GIP

MODEL_OPT_6

OLED

NON_OLED

HD NON_FRC

MODEL_OPT_1 MODEL_OPT_2

R181 100 BCM BT MODULE

MODEL_OPT_3 17page:M_RFMODULE_RESET MODEL_OPT_4 15page:TW_9910_RESET

I/O3

MODEL_OPT_0 +3.3V_NORMAL

NAND_DATA[4]

FRC R1020

NAND_DATA[5]

I/O4

MINI_LVDS/NO LOCAL_D R1011 1K

I/O5

PIN NO.

PIN NAME

NAND_DATA[6]

DDR_512MB R1022 1K

I/O6

MODEL OPTION

*MODEL_OPT_0 & MODEL_OPT_4 REFER TO THIS OPTION

MODEL_OPT_515page:CHB_RESET

MODEL_OPT_0 MODEL_OPT_4

MODEL_OPT_6

LOW

HIGH

LOW

URSA3 Internal

HIGH

URSA3 External

LOW

HIGH

PWIZ Pannel T-con with LG FRC

NO_FRC R1018 1K

NC_9 NAND_IO[0] : Flash Select (1) 0 : Boot From Serial Flash 1 : Boot From NAND Flash

NAND_DATA[7]

LVDS/LOCAL_D R1014 1K

VSS_1

I/O7

FHD R1017

VDD_1

NAND_DATA[0-7]

NC_26

R1001 2.7K

C114 0.1uF

2.7K

NC_8

NC_27

DDR_256MB R1015 1K

R156 2.7K

R1021

C116 4700pF

2.7K

NC_28

NC_7

EXTERNEL FRC/T_CON FRC R1013 1K

NAND_CEb

NC_29

NO FRC/INTERNER FRC R1010 1K

NAND_REb

R1038 2.7K

NAND_CLE

Open Drain

NAND_RBb OPT R1007 2.7K

NC_6 R1035 2.7K

GIP R1009

R157 OPT

NC_5

NAND FLASH

NON_GIP R1023 1K

R1006OPT 2.7K R158 OPT

NAND_ALE

R1003 2.7K

2.7K

NAND_DATA[6] NAND_DATA[7]

NC_4

R1002 OPT 2.7K R1034

NC_3

OLED R118

NAND_DATA[5]

R1037OPT 2.7K

OPT R1004 2.7K

NC_2

NON_OLED R119 1K

NAND_DATA[3]

NAND_DATA[4]

2.7K

R169 2.7K 2.7K

NAND_DATA[0-7]

NC_1

NAND_DATA[2] R1039

IC101 NAND04GW3B2DN6E

R1005 2.7K

R1040 OPT 2.7K

2.7K

R1036 OPT 2.7K

OPT R1008 2.7K

R191

NAND_DATA[0]

R134

R1000

NAND_DATA[0-7]

NO FRC

FOR ESD 12V Pattern

NC_16 +12V

NAND_IO[7] : MIPS Frequency (DNS) 0 : 405MHz 1 : 378MHz

C178 0.1uF 50V

C179 0.1uF 50V

NAND_ALE : I2C Level (DNS) 0 : 3.3V Switching 1 : 5V Switching NAND_CLE 0 : Enable D2CDIFF AC (DNS) 1 : Disabe D2CDIFF AC

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

BCM (EUROBBTV) BCM3556 & NAND FLASH

2009.06.18

When usding FUNDMENTAl then series R = 0 ohm and CL = 8 pF

IC100 LGE3556C (C0 VERSION) D23

A27 F24 F23 E25

A2.5V

C28

LVDS_TX_1_DATA2_N

POD2CHIP_MIVAL

LVDS_TX_1_DATA3_P

CHIP2POD_MCLKO

LVDS_TX_1_DATA3_N

CHIP2POD_MDO0

LVDS_TX_1_DATA4_P

CHIP2POD_MDO1

LVDS_TX_1_DATA4_N

CHIP2POD_MDO2

LVDS_TX_1_CLK_P

CHIP2POD_MDO3

LVDS_TX_1_CLK_N

CHIP2POD_MDO4

LVDS_PLL_VREG

CHIP2POD_MDO5

LVDS_TX_AVDDC1P2

CHIP2POD_MDO6

LVDS_TX_AVDD2P5_1

CHIP2POD_MDO7

LVDS_TX_AVDD2P5_2

CHIP2POD_MOSTRT

LVDS_TX_AVSS_1

CHIP2POD_MOVAL

LVDS_TX_AVSS_2 LVDS_TX_AVSS_3 LVDS_TX_AVSS_4

AC18 AF20 0.1uF

AG21

LVDS_TX_AVSS_5

VDAC_AVDD1P2

LVDS_TX_AVSS_6

VDAC_AVDD3P3_1

LVDS_TX_AVSS_7

VDAC_AVDD3P3_2

C223

0.1uF

C219

0.1uF

C214

BROAD BAND STUDIO

C212

4.7uF

AG20

VDAC_AVDD2P5

LVDS_TX_AVSS_8 LVDS_TX_AVSS_9 LVDS_TX_AVSS_10

AF19 AD20

R220 : BCM recommened resistor 562 ohm +3.3V_NORMAL R220 P200

C215 0.1uF

TJC2508-4A

AH20

C213 0.01uF

75 R238

R201 1.5K

R200 1.5K

AG19 C2028 4.7uF

AE20 560AH22

VDAC_AVSS_1 VDAC_AVSS_3

CLK54_AVDD1P2

VDAC_1

CLK54_AVDD2P5

VDAC_2

CLK54_AVSS CLK54_XTAL_N

VDAC_VREG

CLK54_XTAL_P CLK54_MONITOR

VCXO_AGND_2

R6 R7 T7

A2.5V

T8 R3 U3 L200 BLM18PG121SN1D

T4 T3 R4

0.1uF

4.7uF

0.1uF

R209 3.9K

C201 100pF

0.1uF

Route INCM between associated left and right signals of same channel

0.1uF

U4 V1

BT_DM

BT_DP

SIDE_USB_DM

U2 T5

C209

C208

C207

R210 120

C203

C202

D3.3V SIDE_USB_DP

The INCM trace ends at the same point where the connector ground connects to the board ground (thru-hole connector pin).

R5 R235

Place test points, resistors near audio connector. Connect the other side of the resistor to GND as close as possible to the ground connection of the associated audio connector.

R266

2.7K

R2 T2

2.7K

USB_AVSS_1

VCXO_AGND_3

USB_AVSS_2

VCXO_AVDD1P2

USB_AVSS_3

VCXO_PLL_AUDIO_TESTOUT

P5 P3

A2.5V

A1.2V BLM18PG121SN1D L209

BLM18PG121SN1D

EPHY_RDN EPHY_RDP

EPHY_TDN EPHY_TDP

N3 P1 P4

BLM18PG121SN1D

N4 N1

C2018 4.7uF

C2020 0.1uF

L210

C2021 4.7uF

C244 0.1uF 16V

C2026 4.7uF

C247 0.1uF

L212

N5 P7

USB_AVDD1P2PLL USB_AVDD2P5

RESET_OUTB RESETB NMIB

USB_AVDD2P5REF

TMODE_0

USB_AVDD3P3

TMODE_1

USB_RREF

TMODE_2

USB_DM1

TMODE_3

USB_DP1

SPI_S_MISO

USB_DM2

POR_OTP_VDD2P5

USB_DP2

POR_VDD1P2

USB_MONCDR

R204

C206

0.015uF

AE6

041:B5

REAR_AV_R_IN

R214

C210

0.015uF

AD7

002:J6 REAR_AV_LR_INCM COMP2_L_IN

R215

C211

0.015uF

AH4

COMP2_R_IN

R228

C232

0.015uF

AG5

R229

C220

0.015uF

AG6

R230

C221

0.015uF

AF7

R231

C224

0.015uF

AH5

R232

C225

0.015uF

AG7

R233

C226

0.015uF

AD8

R234

C227

0.015uF

AF8

002:J6 041:B5 041:B5 002:J7 041:B5

AF6

AG4

COMP2_LR_INCM SC1_L_IN SC1_R_IN

AE7

SC1_LR_INCM SIDE_AV_L_IN

041:B5

SIDE_AV_R_IN 002:J6 SIDE_AV_LR_INCM 009:I3 PC_L_IN 009:I3

PC_R_IN

002:J7

PC_LR_INCM

AH6

AE8 AH7 AH8 AG8 AF5 0.047uF C256

0.047uF

0.047uF C254

C253

C252

0.047uF

0.047uF C299

C298

0.047uF

0.047uF C296

C279

0.047uF C277

C2027 0.047uF

0 R265

R264

AB9 AA10 AB10 AA11 C222 0.1uF

AB11 AC8 AE5

PLACE NEAR BCM CHIP

C1 F3 C4 A5 E5

Near Q1705

C258

0.1uF

C2019

0.1uF

C261

0.1uF

TU_CVBS_INCM 003:A3

Run Along TUNER_CVBS_IF_P Trace

E6 D7 E7 F7 G7

SC1_RGB_INCM 003:A4

Near J1500

A1.2V

Run Along SC1_R,SC_G,SC_B Trace A2.5V

AD28 AD26 AC26 AC27 AE25

54MHz_XTAL_N

002:I1

54MHz_XTAL_P

002:I2

REAR_AV_CVBS_INCM 003:A3

Y23

Near J1603 A1.2V

C262

0.1uF

C2015

0.1uF

C2016

0.1uF

C264

0.1uF

COMP2_VID_INCM

Run Along COMP_Y_IN,COMP_Pr_IN,COMP_Pb_IN Trace

AB24 AC24

L203 BLM18PG121SN1D

AF25 AF24

C235 4.7uF

C233 0.1uF

V25 AH3

R_VID_INCM 003:A5

Run Along DSUB_R Trace A2.5V

J4 J3

Near P1600

R221

J5 J6

SYS_RESETb 001:A6;001:B7

4.7K

N24

L211 BLM18PG121SN1D C231 10uF

G_VID_INCM 003:A5

Run Along DSUB_G Trace A1.2V

C234 0.1uF

Run Along DSUB_B Trace

AB8 +3.3V_NORMAL

B_VID_INCM 003:A5

USB_MONPLL

EJTAG_TCK

USB_PWRFLT_1

EJTAG_TDI

USB_PWRFLT_2

EJTAG_TDO

USB_PWRON_1

EJTAG_TMS

USB_PWRON_2

EJTAG_TRSTB

OPT R224 2.7K

H2 H1

OPT R225 2.7K

1K R249

C2011

Near J1500

0.1uF SC1_CVBS_INCM 003:A3

Run Along SC1_CVBS_IN Trace

EJTAG_CE1 EPHY_VREF EPHY_RDAC

A1.2V L204 BLM18PG121SN1D

AB26

EPHY_RDN

PLL_MAIN_AVDD1P2

EPHY_RDP

PLL_MAIN_AGND

EPHY_TDN

PLL_MAIN_MIPS_EREF_TESTOUT

EPHY_TDP

PLL_RAP_AVD_TESTOUT

EPHY_AVDD1P2

PLL_RAP_AVD_AVDD1P2

EPHY_AVDD2P5

PLL_RAP_AVD_AGND

EPHY_AGND_1 EPHY_AGND_2

2.7K

R227 2.7K

AB27 M6 N6

R240 A1.2V L207 BLM18PG121SN1D

390 OPT

C2023

Near J1501

0.1uF

SIDE_AV_CVBS_INCM 003:A3

Run Along SC2_CVBS_IN Trace

AA24 BYP_CPU_CLK BYP_DS_CLK BYP_SYS175_CLK

AUDMX_LEFT1

R226

AC25

EPHY_PLL_VDD1P2

BYP_SYS216_CLK REAR_AV_L_IN

VIDEO INCM

P24

USB_AVDD1P2

EPHY_AGND_3

041:B5

A1.2V A2.5V

013:E7;035:AK13

+3.3V_NORMAL

USB_AVSS_5

P6 1K R219

LVDS_TX_0_CLK_P

OPT

C228 10uF

USB_AVSS_4

EJTAG_CE0 R218 240

AA23 VCXO_AGND_1

LVDS_TX_0_DATA0_P013:E7;035:AK11 LVDS_TX_0_CLK_N 013:E7;035:AK13

12pF C229

LVDS_TX_0_DATA0_N013:E7;035:AK11

22 R211

LVDS_TX_0_DATA1_P013:E7;035:AK11

BSC_S_SCL BSC_S_SDA

A1.2V

LVDS_TX_0_DATA1_N013:E7;035:AK12

PM_OVERRIDE

A3.3V

LVDS_TX_0_DATA2_P013:F7;035:AK12

AD27

VDAC_RBIAS

M25

LVDS_TX_0_DATA2_N013:F7;035:AK12

VDAC_AVSS_2

AH21

M24

LVDS_TX_0_DATA3_P013:F7;035:AK14

LVDS_TX_AVSS_11

DTV/MNT_V_OUT

LVDS_TX_0_DATA3_N013:F7;035:AK14

LVDS_TX_1_DATA2_P

POD2CHIP_MISTRT

LVDS_TX_1_DATA1_N

POD2CHIP_MDI7

54MHz_XTAL_P

LVDS_TX_0_DATA4_P013:F7;035:AK14

X903 54MHz

POD2CHIP_MDI6

54MHz_XTAL_N

013:E7;035:AK18

LVDS_TX_0_DATA4_N013:F7;035:AK15

LVDS_TX_1_DATA1_P

L202 BLM18PG121SN1D

R237

R236

A28

POD2CHIP_MDI5

LVDS_TX_1_CLK_P

R250 34

B27

LVDS_TX_1_DATA0_N

R251 34

B28

LVDS_TX_1_DATA0_P

POD2CHIP_MDI4

R248 34

C26

POD2CHIP_MDI3

LVDS_TX_1_DATA0_P013:E7;035:AK16 LVDS_TX_1_CLK_N 013:E7;035:AK18

R244 34

C27

LVDS_TX_0_CLK_N

R245 34

F25

POD2CHIP_MDI2

LVDS_TX_1_DATA0_N013:E7;035:AK16

R247 34

E24

LVDS_TX_0_CLK_P

R246 34

E23

CI_OUTVALID

POD2CHIP_MDI1

LVDS_TX_1_DATA1_P013:E7;035:AK16

R260 34

CI_OUTSTART

LVDS_TX_0_DATA4_N

R261 34

CI_OUTDATA[6] D27 CI_OUTDATA[7] D26

POD2CHIP_MDI0

LVDS_TX_1_DATA1_N013:E7;035:AK17

4.7uF

CI_OUTDATA[4] E26 CI_OUTDATA[5] D28

LVDS_TX_0_DATA4_P

0.1uF C240

CI_OUTDATA[2] C25 CI_OUTDATA[3] E27

POD2CHIP_MCLKI

LVDS_TX_1_DATA2_P013:E7;035:AK17

C251

CI_OUTDATA[0] D25 CI_OUTDATA[1] D24

A3.3V A1.2V

LVDS_TX_0_DATA3_N

G23

LVDS_TX_1_DATA2_N013:E7;035:AK17

C257

LVDS_TX_0_DATA2_N LVDS_TX_0_DATA3_P

CI_A[14]

C230 12pF

22 R212

LVDS_TX_1_DATA3_P013:E7;035:AK19

L208

RMX0_SYNC

CI_OUTDATA[0-7],CI_OUTSTART,CI_OUTVALID 045:V14

LVDS_TX_1_DATA3_N013:E7;035:AK19

1008LS-272XJLC 33pF

LVDS_TX_0_DATA2_P

R243 604

RMX0_DATA

LVDS_TX_1_DATA4_P013:E7;035:AK19

0.1uF

LVDS_TX_0_DATA1_N

C237

TP4023

RMX0_CLK

LVDS_TX_1_DATA4_N013:E7;035:AK20

4.7uF

A26

LVDS_TX_0_DATA1_P

C236 0.1uF

TP4022

LVDS_TX_0_DATA0_N

PKT0_SYNC

C239 0.1uF C242 4.7uF C295 0.1uF C2013 4.7uF

B25

LVDS_TX_0_DATA0_P

PKT0_DATA

C2012 0.1uF

A25 TP4021

When usding Dip-type X-tal then series R = 22 ohm and CL = 12 pF

B4 PKT0_CLK

C241

B26

0.1uF

C24

FE_TS_SYNC

C238

FE_TS_DATA_CLK FE_TS_SERIAL

54MHz X-TAL

Y24 AE24

R222

AD25

R262

TP is Necessory

AUDIO INCM

AUDMX_RIGHT1 AUDMX_INCM1

PLACE NEAR BCM CHIP

AUDMX_LEFT2 AUDMX_RIGHT2 AUDMX_INCM2

PLACE NEAR Jacks

AUDMX_LEFT3

5.1

AUDMX_RIGHT3 AUDMX_INCM3

Near J1501

R256

Route Between SC2_L_IN & SC2_R_IN

AUDMX_LEFT4

0.15uF C2014

AUDMX_RIGHT4

SIDE_AV_LR_INCM 002:C6 0.47uF C271

AUDMX_INCM4 5.1

AUDMX_LEFT5 AUDMX_RIGHT5

Near J1600

AUDMX_INCM5

002:C6 REAR_AV_LR_INCM R258

Route Between AV1_L_IN & AV1_R_IN

AUDMX_LEFT6

0.15uF C2024

0.47uF C2017

AUDMX_RIGHT6 AUDMX_INCM6 AUDMX_AVSS_1 5.1

AUDMX_AVSS_2 AUDMX_AVSS_3 AUDMX_AVSS_4

Near J1603

R259

Route Between COMP1_L_IN & COMP1_R_IN

0.15uF C265

Route Between SC1_L_IN & SC1_R_IN

0.15uF C2022

AUDMX_AVSS_5

COMP2_LR_INCM 002:C6 C2025 0.47uF

AUDMX_AVSS_6 AUDMX_LDO_CAP AUDMX_AVDD2P5 5.1

Near J1500

R257

A2.5V

C217 10uF

SC1_LR_INCM 002:C6 0.47uF C270

5.1

Near J1602

R252

Route Between PC_L_IN & PC_R_IN

0.15uF C269

PC_LR_INCM 002:C6 0.47uF C2010

Near Q1704 TU_SIF_INCM

Route Along With TUNER_SIF_IF_N

BCM (EUROBBTV) BCM3556 AUD_IN/LVDS

003:A3

2009.06.18

D1.2V

Place here for common circuit with ATSC +1.8V_AMP

+1.8V_HDMI

+3.3V_NORMAL

L111 BLM18PG121SN1D

D3.3V

D1.2V

A3.3V

L112 CIC21J501NE

C249 4.7uF

C243 0.1uF

C250 1000pF

C382 0.01uF

C380 10uF

C381 0.1uF

C379 10uF

C286 33uF

C287 100uF

C383 1000pF

C246 0.01uF

C376 4.7uF

C378 0.1uF

C259 1000pF

C366 0.1uF

C374 0.01uF

C266 4.7uF

C255 1000pF

C245 4.7uF

C290 0.01uF

C288 1000pF

C377 0.01uF

C375 0.1uF

C373 1000pF

C263 4.7uF

C267 0.01uF

C289 0.1uF

FOR ESD

C2008 0.1uF 16V

C2007 0.1uF 16V

D3.3V

AE26 AE28

TU_IF_P_1

C172 4.7uF

C113 0.1uF L103

A1.2V TU_IF_N_1

C119 0.1uF

BLM18PG121SN1D A1.2V

AE27 AD24

C144 0.1uF

AB19 AB25

C122 4.7uF

I2S_DATA_OUT

EDSAFE_AVSS_3

I2S_LR_IN

EDSAFE_AVSS_4

I2S_LR_OUT

EDSAFE_AVSS_5

AUD_LEFT0_N

EDSAFE_AVDD2P5

AUD_LEFT0_P

EDSAFE_DVDD1P2

AUD_AVDD2P5_0

EDSAFE_IF_N

AUD_AVSS_0_1

EDSAFE_IF_P

AUD_AVSS_0_2

PLL_DS_AGND

AUD_AVSS_0_3

PLL_DS_AVDD1P2

AUD_AVSS_0_4

PLL_DS_TESTOUT

AUD_AVSS_0_5 AUD_RIGHT0_N

A2.5V

AUD_RIGHT0_P

AB18 C112 0.1uF

C111 0.1uF

BLM18PG121SN1D

AC17

L105 C117 1000pF

AB17

C123 0.01uF

L104 C120 1000pF BLM18PG121SN1D

AD14 AD16 AB15 AC15 AD13

C118 0.01uF

AE13 AC13

DSUB

AB14 DSUB_R

AC14

R_VID_INCM DSUB_G

AC12

G_VID_INCM DSUB_B

AB13

AD12 AA14 AC11

B_VID_INCM

AD11

10 C169 47pF

SC1_RGB(EU)/COMPNENT1[NON_EU]

C101 47pF

C127

0.1uF

AE9 AH9

C130

0.1uF

AG15

C131

0.1uF

AE15

C132

0.1uF

AF15 AH15

OPT 75 R135

C105 OPT NON_EU 75 R315

SC1_RGB_INCM

SIDE COMPONENT

NON_EU

COMP1_Pr ==> SC1_R COMP1_Pb ==> SC1_B

0.1uF

C129

R138

C128

AG9

EU 0

1% NON_EU R313

SC1_G

AD10

AF9

NON_EU COMP1_Y ==>

0.1uF

AC10

R312 75

1% R120 82

R138-*1

C104 OPT

COMP2_VID_INCM

R131 75

COMP2_Pb

AB12 C17047pF

R195

COMP2_Pr

ONLY USE NON_EU FOR COMP 1

R135-*1

0.1uF

C134

0.1uF

AF16

C135

0.1uF

AH17

82 1%

C174

0.1uF

AG14

C175

0.1uF

AE14

C176

0.1uF

AH10 AG10

R166 75

R167 75

1% R165 82

SIDE_COMP_Y

C177 OPT

SIDE_COMP_Pb SIDE_COMP_INCM

R100 R142 R143 R141

SIDE_COMP_Pb SIDE_COMP_INCM EU_CN R2112

TU_CVBS 1% 18

REAR_AV_CVBS

AF11 AH13 AE12 AF12 C110

0.1uF

AD9

C124

0.1uF

AG11

C125 R2115

AH11

62 OPT 62 75 1% EU_CN

R2114

SIDE_AV_CVBS

AE11

R2113

SC1_CVBS_IN

AE10

NON_EU_CN NON_EU_CN R141-*1 R2112-*1 5% 12

SIDE_COMP_Pr

CVBS

C100

0.1uF 0.1uF

AG12 AF13 AC9

TU_CVBS_INCM REAR_AV_CVBS_INCM

AF10 A2.5V

SC1_CVBS_INCM

AH12

A2.5V

AG13 R137 10K

R4020 10K

0.1uF C106

R128 0

AG17 AD15 A1.2V

SC1_ID

OPT

L106 BLM18PG121SN1D R3055 240

R139 12K

C121 0.1uF

C140 4.7uF

AE16 AE17 AB16 AA15 AC16 AG3

12K R4021

120 R3056

TU_SIF_INCM OPT

AUD_LEFT1_N

SD_V5_AVDD2P5

AUD_LEFT1_P AUD_RIGHT1_N

SD_V5_AVSS SD_V1_AVDD1P2

AUD_RIGHT1_P

SD_V1_AVDD2P5

AUD_AVDD2P5_1

SD_V1_AVSS_1

AUD_AVSS_1_1

SD_V1_AVSS_2

AUD_AVSS_1_2

SD_V2_AVDD1P2

AUD_AVSS_1_3

SD_V2_AVDD2P5

C4020 0.1uF

AF4

AUD_LEFT2_N

SD_V2_AVSS_1

AUD_LEFT2_P

SD_V2_AVSS_2

AUD_RIGHT2_N

SD_V2_AVSS_3

AUD_RIGHT2_P

SD_V3_AVDD1P2

AUD_AVDD2P5_2

SD_V3_AVDD2P5

AUD_AVSS_2_1

SD_V3_AVSS_1

AUD_AVSS_2_2

SD_V3_AVSS_2

AUD_SPDIF

SD_V4_AVDD1P2

SPDIF_AVDD2P5

SD_V4_AVDD2P5

SPDIF_AVSS

SD_V4_AVSS

SPDIF_IN_N

SD_R

SPDIF_IN_P

SD_G HDMI_RX_0_HTPLG_IN

SD_B

HDMI_RX_0_HTPLG_OUT

SD_INCM_B SD_Y1

HDMI_RX_0_DDC_SCL

SD_PR1

HDMI_RX_0_DDC_SDA

SD_PB1

HDMI_RX_0_RESREF

SD_INCM_COMP1

HDMI_RX_0_CLK_N

SD_Y2

HDMI_RX_0_CLK_P

SD_PR2

HDMI_RX_0_DATA0_N

SD_PB2

HDMI_RX_0_DATA0_P

SD_INCM_COMP2

HDMI_RX_0_DATA1_N

SD_Y3

HDMI_RX_0_DATA1_P

SD_PR3

HDMI_RX_0_DATA2_N

SD_PB3

HDMI_RX_0_DATA2_P

SD_INCM_COMP3

HDMI_RX_0_VDD3P3

SD_L1

HDMI_RX_0_VDD1P2

SD_C1

HDMI_RX_0_VDD2P5

SD_INCM_LC1

HDMI_RX_0_AVSS_1

SD_L2

HDMI_RX_0_AVSS_2

SD_C2

HDMI_RX_0_AVSS_3

SD_INCM_LC2

HDMI_RX_0_AVSS_4

SD_L3

HDMI_RX_0_AVSS_5

SD_C3

HDMI_RX_0_AVSS_6

SD_INCM_LC3

HDMI_RX_0_PLL_AVSS

SD_CVBS1

HDMI_RX_0_PLL_DVDD1P2

SD_CVBS2

HDMI_RX_0_PLL_DVSS

SD_CVBS4 SD_INCM_CVBS1

HDMI_RX_1_CEC_DAT

SD_INCM_CVBS2 HDMI_RX_1_HTPLG_IN SD_INCM_CVBS3 HDMI_RX_1_HTPLG_OUT HDMI_RX_1_DDC_SCL

SD_SIF1

HDMI_RX_1_DDC_SDA

SD_INCM_SIF1

HDMI_RX_1_RESREF

SD_FB

HDMI_RX_1_CLK_N

SD_FS

HDMI_RX_1_CLK_P

SD_FS2

HDMI_RX_1_DATA0_N HDMI_RX_1_DATA0_P PLL_VAFE_AVDD1P2 PLL_VAFE_AVSS HDMI_RX_1_DATA1_N HDMI_RX_1_DATA1_P PLL_VAFE_TESTOUT RGB_HSYNC HDMI_RX_1_DATA2_N HDMI_RX_1_DATA2_P HDMI_RX_1_VDD1P2 HDMI_RX_1_VDD2P5 HDMI_RX_1_AVSS_1

RGB_HSYNC

HDMI_RX_1_AVSS_2

RGB_VSYNC

HDMI_RX_1_AVSS_3 HDMI_RX_1_AVSS_4 HDMI_RX_1_AVSS_5

SC1_FB

HDMI_RX_1_AVSS_6 HDMI_RX_1_AVSS_7

OPT

HDMI_RX_1_AVSS_8 0 R2116

AH26

HDMI_RX_1_AVSS_9 HDMI_RX_1_PLL_AVSS HDMI_RX_1_PLL_DVDD1P2 HDMI_RX_1_PLL_DVSS

C370 0.1uF

C292 1000pF

C293 0.01uF

C294 0.1uF

C272 0.1uF

C274 0.1uF

C275 0.1uF

C278 4.7uF

C276 0.1uF

C280 4.7uF

C297 4.7uF

C2004 33uF

A2.5V

HP_LOUT_P

AA20

C147 0.01uF

AB21

C155 0.1uF

C162 10uF

AC22

D1.8V

AC23 AD23 AH25

D1.8V

HP_ROUT_N

AG25

HP_ROUT_P

AH23 BT_LOUT_N

AG23

BT_LOUT_P

AG24

C248 1000pF

BT_ROUT_N

AH24

C281 1000pF

C282 1000pF

C283 1000pF

C284 0.01uF

C285 0.01uF

C2005 0.01uF

BT_ROUT_P

AE22 AB20

C148 0.01uF

AC21

C2006 0.01uF

C365 0.1uF 16V

C364 0.1uF 16V

C357 10uF 10V

C363 0.1uF 16V

C356 0.1uF 16V

C348 0.1uF 16V

C320 0.1uF 16V

C318 0.1uF 16V

C319 0.1uF 16V

C304 0.1uF 16V

C163 10uF

C156 0.1uF

AE23 AF21

SCART1_Lout_N

AE21

SCART1_Lout_P

AF22

SCART1_Rout_N

AG22

SCART1_Rout_P

AD21 AC20

C149 0.01uF

AD22

C164 10uF

C157 0.1uF

AH2 SPDIF_OUT

AC6 AE4

C150 0.1uF

AF3

+5V_NORMAL

IC100 LGE3556C (C0 VERSION)

AH1

R2036 1K

D1.2V

AA6 AA5

R309

10K

AB3

R307

R308

AC4

499

IC100 LGE3556C (C0 VERSION)

HDMI_CLK+

AD1

C3006 0.1uF 16V

HDMI_CLK-

AC2

L8 M8

HDMI_RX0-

AD2

N8 A3.3V

HDMI_RX0+

AE1

HDMI_RX1-

AE2

HDMI_RX1+

AF1

HDMI_RX2-

AF2

HDMI_RX2+

AD3

BLM18PG121SN1D L109

AA8

A1.2V

H10

A2.5V

H11

AE3

H12

AC3 C145 4.7uF

H13

C160 0.1uF

C153 0.1uF

H14 BLM18PG121SN1D L107

AB6

H15

AG2

H16

AB4

H17

AA7

H18

H19 C151 0.01uF

C158 1000pF

AC5

C165 10uF

H21 J21

K21

V4 U6 V5

D3.3V

L21 M21 N21 P21 R21 T21

V3 W4 W2

499

A3.3V

R153

U21 V21

OPT

W21

W3 R205 20

Y1 Y2

Y21

VDDC_2

VDDC_3

AB7

VDDC_4

AC7

VDDC_5

VDDC_6

VDDC_7

AA9

VDDC_8

G10

VDDC_9

A11

VDDC_10

L11

VDDC_11

M11

VDDC_12

N11

VDDC_13

P11

VDDC_14

R11

VDDC_15

T11

VDDC_16

U11

VDDC_17

V11

VDDC_18

D12

VDDC_19

G12

VDDC_20

L12

VDDC_21

M12

VDDC_22

N12

VDDC_23

P12

VDDC_24

R12

VDDC_25

T12

VDDC_26

U12

VDDC_27

V12

VDDC_28

L13

VDDC_29

M13

VDDC_30

N13

VDDC_31

P13

VDDC_32

R13

VDDC_33

T13 V13

AH27

AB1

A1.2V

A2.5V

C2003 0.1uF

L14

AA13

AA18

AA19 C154 0.1uF

E28

C161 0.1uF

L28 U28

FOR ESD

AB28

V7 BLM18PG121SN1D L108

W7 U8 V8

C384 33uF 10V

VDDO_2

P14

VDDO_3

R14

VDDO_4

T14

VDDO_5

U14

VDDO_6

V14

VDDO_7

L15

VDDO_8

M15 P15

G11

AA4

G13 C166 10uF

N14

N15

C152 0.01uF

VDDO_1

D1.8V

C159 1000pF

M14

AA12

C146 4.7uF

G14

AGC_VDDO

D3.3V

BLM18PG121SN1D L110

AB2

U13

AA1

VDDC_1

A3.3V

AA2

HDMI_SDA

R152

AB5

AD6 J7

HDMI_SCL

AC1

AD4

AD5

A2.5V

A14 G15 G17 A19 G19

C369 4.7uF

AF23

AA3

HDMI_RX_1_VDD3P3

R2117 0

AUD_LRCK HP_LOUT_N

AG26

SD_CVBS3

RGB_VSYNC

CONNECT NEAR BCM CHIP

AG18

AG1 HDMI_RX_0_CEC_DAT

SD_INCM_G

C371 0.01uF

AUD_LRCH

AD18

SD_INCM_R

SD_INCM_CVBS4 AF17

SIDE_AV_CVBS_INCM

TU_SIF

AF14 AH14

SIDE_COMP_Pr

AG16

AH16

R196 10 SIDE_COMP_Y

C133

SD_V5_AVDD1P2

AH19

R2035 0

AG27

TU_IF_N_1 TU_IF_P_1

EDSAFE_AVSS_2

C268 1000pF

AUD_SCK

AD17

10K

AF28

AF18

R2039

AF27

I2S_DATA_IN

10K

AF26 A1.2V BLM18PG121SN1D L102

I2S_CLK_OUT

EDSAFE_AVSS_1

10K

TU_IF_AGC_1 TU_IF_AGC_2

I2S_CLK_IN

DS_AGCT_CTL

R310

AB22

A2.5V

DS_AGCI_CTL

R2038

AA21

R2037 OPT 10K

AH28

TU_IF_AGC_2

C216 0.1uF

AE18

AG28

TU_IF_AGC_1

COMP2_Y

D1.8V

IC100 LGE3556C (C0 VERSION)

26page : TUNER(HALF NIM)

COMPONENT

C291 10uF

DDRV_1

R15

DDRV_2

T15

DDRV_3

U15

DDRV_4

V15

DDRV_5

A16

DDRV_6

G16

DDRV_7

L16

DDRV_8

M16

DDRV_9

N16

P16 DVSS_1

DVSS_62

DVSS_2

DVSS_63

DVSS_3

DVSS_64

DVSS_4

DVSS_65

DVSS_5

DVSS_66

DVSS_6

DVSS_67

DVSS_7

DVSS_68

DVSS_8

DVSS_69

DVSS_9

DVSS_70

DVSS_10

DVSS_71

DVSS_11

DVSS_72

DVSS_12

DVSS_73

DVSS_13

DVSS_74

DVSS_14

DVSS_75

DVSS_15

DVSS_76

DVSS_16

DVSS_77

DVSS_17

DVSS_78

DVSS_18

DVSS_79

DVSS_19

DVSS_80

DVSS_20

DVSS_81

DVSS_21

DVSS_82

DVSS_22

DVSS_83

DVSS_23

DVSS_84

DVSS_24

DVSS_85

DVSS_25

DVSS_86

DVSS_26

DVSS_87

DVSS_27

DVSS_88

DVSS_28

DVSS_89

DVSS_29

DVSS_90

DVSS_30

DVSS_91

DVSS_31

DVSS_92

DVSS_32

DVSS_93

DVSS_33

DVSS_94

DVSS_34

DVSS_95

DVSS_35

DVSS_96

DVSS_36

DVSS_97

DVSS_37

DVSS_98

DVSS_38

DVSS_99

DVSS_39

DVSS_100

DVSS_40

DVSS_101

DVSS_41

DVSS_102

DVSS_42

DVSS_103

DVSS_43

DVSS_104

DVSS_44

DVSS_105

DVSS_45

DVSS_106

DVSS_46

DVSS_107

DVSS_47

DVSS_108

DVSS_48

DVSS_109

DVSS_49

DVSS_110

DVSS_50

DVSS_111

DVSS_51

DVSS_112

DVSS_52

DVSS_113

DVSS_53

DVSS_114

DVSS_54

DVSS_115

DVSS_55

DVSS_116

DVSS_56

DVSS_117

R16 T16 U16 V16 AA16 D17 L17 M17 N17 P17 R17 T17 U17 V17 AA17 AC19 G18 L18 M18 N18 P18 R18 T18 U18 V18 D20 G20 H20 A21 E21 F21 G21 E22 F22 G22 H22 J22 K22 L22 M22 N22 P22 R22 T22 U22 V22 W22 Y22 AA22 W23 AB23 F28 M28 T28 AC28

DVSS_57 DVSS_58 DVSS_59 DVSS_60 DVSS_61

EUROBBTV BCM3556 VIDEO IN

2009.06.18

D1.8V A1.2V

IC100 LGE3556C (C0 VERSION)

DDR0_A04 DDR0_A05 DDR0_A06 DDR01_A07 DDR01_A08 DDR01_A09 DDR01_A10 DDR01_A11 DDR01_A12 DDR01_A13 DDR1_A04 DDR1_A05 DDR1_A06 DDR01_BA0 DDR01_BA1 DDR01_BA2 DDR01_CASB DDR0_DQ00 DDR0_DQ01 DDR0_DQ02 DDR0_DQ03 DDR0_DQ04 DDR0_DQ05 DDR0_DQ06 DDR0_DQ07 DDR0_DQ08 DDR0_DQ09 DDR0_DQ10 DDR0_DQ11 DDR0_DQ12 DDR0_DQ13 DDR0_DQ14 DDR0_DQ15 DDR1_DQ00 DDR1_DQ01 DDR1_DQ02 DDR1_DQ03 DDR1_DQ04 DDR1_DQ05 DDR1_DQ06 DDR1_DQ07 DDR1_DQ08 DDR1_DQ09 DDR1_DQ10 DDR1_DQ11 DDR1_DQ12 DDR1_DQ13 DDR1_DQ14 DDR1_DQ15 DDR0_DM0 DDR0_DM1 DDR1_DM0 DDR1_DM1 DDR0_DQS0 DDR0_DQS0B DDR0_DQS1 DDR0_DQS1B DDR1_DQS0 DDR1_DQS0B DDR1_DQS1 DDR1_DQS1B DDR01_RASB DDR_VREF0 DDR_VREF1 DDR01_WEB DDR_VDDP1P8_1

A12

004:A7;004:C4

DDR1_CLKb 004:F7;004:F4 DDR01_A[1]

A15

DDR01_A[2]

D15

DDR01_A[3]

E13

DDR0_A[4]

F13

DDR0_A[6]

C14

DDR01_A[7] DDR01_A[9]

D14

DDR01_A[10]

C13

DDR01_A[11]

D13

DDR01_A[12]

B13

DDR01_A[13]

C15

DDR1_A[5]

D16

DDR1_A[6]

DDR01_RASb

DDR01_CASb

DDR01_WEb

F3 G8

G3 G1

DDR01_BA2

CAS WE

DQ6

DDR0_A[4-6] DDR1_A[4-6]

DDR01_A[0] DDR01_A[1]

DDR01_A[2]

H7 J2

DDR0_A[5]

DDR01_BA2

A17

DDR01_CASb

DDR0_A[6]

DDR01_A[7]

DDR01_A[8]

DDR01_A[9]

DDR0_DQ[0]

B11

DDR0_DQ[1]

DDR0_DQ[2]

DDR01_A[10]

D11

DDR0_DQ[3] DDR0_DQ[4]

DDR01_A[11] DDR01_A[12]

E11 C8

DDR0_DQ[5]

DDR01_A[13]

DDR01_CKE

DDR0_DQ[3]

DQ0

DQ1

CKE

DQ2 DQ3

DDR0_DQ[4]

DDR0_DQ[5]

DDR01_RASb

DDR0_DQ[6]

DDR01_CASb

DDR0_DQ[7]

DDR01_WEb

DQ7

DQ4 RAS CAS WE

DQ5 DQ6

DDR1_DQ[0]

DDR1_DQ[1]

DDR1_DQ[5]

DDR1_DQ[3]

DDR1_A[4-6]

DDR1_A[6]

DQS BA0

DQS

BA1

DM/RDQS

NC_1/BA2

NU/RDQS

DDR0_DQS0

DDR0_DQS0b

DDR0_DM0

DDR1_DQ[4]

DDR1_DQ[2]

R408

DDR1_DQ[6]

DDR01_A[12] R409

DDR1_DQ[7]

DDR01_A[9]

DQ7

DDR0_A[4-6]

DDR01_CASb

DDR01_BA1

004:A4 004:A4

G2 G3 G1

DDR01_BA2

DDR0_DQ[0-7]

DQS BA0

DQS

BA1

DM/RDQS

NC_1/BA2

NU/RDQS

DDR1_DQS0

DDR1_DQS0b

DDR1_A[4]

004:A4

DDR1_DM0

004:A3

DDR01_A[11] DDR01_A[8]

VDDQ_1

VDDQ_2

VDDQ_3

VDDQ_4

VDDQ_5

VDD_1

VDD_2

VDD_3

VSSQ_1

A11

VSSQ_2 VSSQ_3 VSSQ_4 VSSQ_5 VSS_1

DDR01_A[2]

DDR01_A[3] DDR1_A[4]

C9 A1

DDR1_A[5]

004:B6;004:F3;004:I7 DDR1_A[4-6]

VSS_2

DDR1_A[6]

DDR01_A[7]

DDR01_A[8]

DDR01_A[9]

DDR01_A[10]

DDR01_A[11]

DDR01_A[12]

DDR01_A[13]

A10/AP

DDR0_DQ[8-15]

DDR01_A[1]

VDD_4

A12

DDR01_A[0]

A9 A0

VDDQ_1

VDDQ_2

VDDQ_3

VDDQ_4

VDDQ_5

VDD_1

VDD_2

VDD_3

VSSQ_1

A11

VSSQ_2

A12

VSSQ_3

A13

VSSQ_4 VSS_1

DDR01_WEb

DDR01_CKE DDR01_ODT

L1 E9

R410

DDR_VTT

VSS_2

DDR01_RASb DDR01_A[2]

A3 E3

DDR0_DQ[15] DDR1_DQ[0] DDR1_DQ[1]

DDR0_A[5]

A18

DDR1_DQ[2]

DDR0_A[4]

DDR1_DQ[3] DDR1_DQ[5]

B20

DDR1_DQ[6]

D18 E18

DDR1_DQ[7] DDR1_DQ[8]

D21

DDR1_DQ[9]

VREF VDDL

DDR1_DQ[13]

B22

DDR1_DQ[14]

E17

DDR01_A[3]

VSS_4

DDR1_DQ[15]

ODT

C452

VREF VDDL

C463

75 DDR01_BA1 DDR01_A[12] AR406

C466

VSSDL

470pF 0.1uF

DDR01_A[9]

Close to IC

C492 0.1uF

DDR01_A[8] DDR01_A[13]

DDR01_CKE DDR01_ODT

75 AR408 C493 0.1uF 75 AR409 R404

F19 B10

IC401 NT5TU128M8DE_BD 004:A7;004:C7

DDR0_DQS0 004:E6 DDR0_DQS0b 004:E6 DDR0_DQS1 004:E3

B9 F10 F9

E8 F8

004:A7;004:C7 DDR01_CKE 004:A7;004:C7;004:F7;004:F4

DDR1_DQS0b 004:H6

DDR01_RASb

DDR1_DQS1 004:H3 DDR1_DQS1b 004:H3 DDR01_RASb

DDR01_CASb

DDR01_WEb

DDR0_VREF0 DDR1_VREF0

A7 A23

DQ1

CKE

DQ2

DQ4 RAS

DQ5

CAS

DQ6

DQ7

DDR01_WEb

C7 D22 C424 0.1uF

C427 0.1uF

0.1uF

G3 G1

BA0

DQS

BA1

DM/RDQS

NC_1/BA2

NU/RDQS

DDR01_A[1]

DDR01_A[2]

DDR01_A[3]

DDR0_A[4]

DDR0_A[5]

DDR0_A[6]

DDR01_A[7]

K2 K8

DDR01_A[9]

DDR01_A[10]

DDR01_A[11]

DDR01_A[12]

DDR01_A[13]

VDDQ_1

VDDQ_2

VDDQ_3

VDDQ_4

VDDQ_5

VDD_1

VDD_2

VDD_3

VDD_4

A9 VSSQ_1

A11

VSSQ_2

A12

VSSQ_3

A13

VSSQ_4

10K

R418

L3 NC_2/A14 NC_3/A15

VTTS

DDR0_VREF0 VREF

DQ0

DQ1

CKE

DQ2 DQ3

DDR0_DQ[11]

DDR01_RASb

DDR0_DQ[10]

DDR01_CASb

DDR01_WEb

DDR0_DQ[14]

DQ4 RAS

DQ5

CAS

DQ6

DQ7

DDR1_DQ[9]

DDR1_DQ[8]

DDR1_DQ[12]

DDR1_DQ[13]

DDR1_DQ[15]

DDR1_DQ[14]

DDR1_DQ[10]

DDR1_DQ[11]

C497 0.1uF C498 0.1uF

DDR0_DQS1

004:A4

DDR0_DQS1b

004:A4

DDR0_DM1

DDR01_BA1

VSS_2 VSS_3

DQS

G2 G3

004:A4

DDR01_BA2

BA0

DQS

BA1

DM/RDQS

NC_1/BA2

NU/RDQS

DDR1_DQS1

DDR1_DQS1b

DDR1_A[4-6] 004:B6;004:F6;004:I7

H8 H3

DDR01_A[2]

DDR01_A[3]

DDR1_A[4]

DDR1_A[5]

DDR1_A[6]

DDR01_A[7]

DDR01_A[8]

DDR01_A[9]

DDR01_A[10]

DDR01_A[11]

DDR01_A[12]

DDR01_A[13]

A9 A0

VDDQ_1

VDDQ_2

VDDQ_3

VDDQ_4

VDDQ_5

VDD_1

VDD_2

VDD_3

VDD_4

A9 VSSQ_1

A11

VSSQ_2

A12

VSSQ_3

A13

VSSQ_4 VSSQ_5 VSS_1

DDR0_VREF0

NC_2/A14 NC_3/A15

VSS_4

C1 C3 C7 C9 A1 L1 E9 H9 A7

A10/AP

A3 E3

004:A3 004:A4

D1.8V DDR01_A[0] DDR01_A[1]

004:A3

DDR1_DM1

DDR01_A[0-3,7-13]

VSS_2 VSS_3

B2 B8 D2 D8 A3 E3 J1 K9

DDR1_VREF0

VSS_4

VTT DDR01_ODT

F9 ODT

VREF VDDL

VTT_IN

VSSDL

E1 E7

DDR01_ODT C450

C453

0.1uF 470pF

F9 ODT

VREF VDDL VSSDL

C464

C467

E7 470pF 0.1uF

VCC

VDDQ

C422 1uF 10V

R417 220

C416 10uF 10V

C420 0.1uF 16V

Close to IC

C418 1uF 10V

Close to IC

0.1uF

DDR0_DQ[15]

A10/AP

VSS_1

D1.8V

DDR01_CKE

DDR0_DQ[13]

VSSQ_5

DDR1_VREF0

DDR0_DQ[12]

D1.8V DDR01_A[0]

D3.3V

DDR01_A[0-3,7-13]

DDR01_A[8]

CS DQS

* DDR_VTT

GND

DDR1_CLKb

DDR01_BA0

DDR01_BA2

IC404 BD35331F-E2

DDR0_DQ[8]

DDR0_A[4-6]

DDR_VTT

DDR0_DQ[9]

C494 0.1uF

004:B5

DDR01_BA0 DDR01_BA1

C17 D1.8V

DQ0

DQ3

E19 C16

C496 0.1uF

DDR1_DQ[8-15]

DDR1_CLK

C19 D19

IC403 NT5TU128M8DE_BD

DDR0_DQ[8-15]

DDR0_CLK

DDR0_CLKb

DDR0_DQS1b 004:E3 DDR1_DQS0 004:H6

B19

16V

DDR01_A[11]

DDR01_WEb

DDR0_DM0 004:E6

C414

C484 0.1uF 75 AR407

DDR01_BA2

DDR0_DM1 004:E3 DDR1_DM0 004:H6 DDR1_DM1 004:H3

C413 0.1uF 16V

C483 0.1uF

DDR01_A[10]

DDR01_BA0

A20

C415

75 AR405

DDR01_A[1] E2

0.1uF 470pF

DDR1_DQ[8-15]

C10

C423 10uF 10V

DDR0_A[6]

DDR1_VREF0

DDR01_A[7]

A10

VSSDL

DDR1_DQ[0-7]

C449

DDR1_DQ[11] DDR1_DQ[12]

F17

R415

004:A7;004:C5;004:C2;004:F2;004:I4;004:I6 DDR01_ODT

VSS_3

DDR1_DQ[10]

A22

NC_3/A15

E2 ODT

NC_2/A14

C491 0.1uF

DDR01_A[0]

C20

DDR0_VREF0

VSS_4

DDR01_ODT

C18

VSS_3

C421 0.1uF

NC_3/A15

C499 0.1uF 75

DDR0_DQ[14]

NC_2/A14

75 AR404

D10

R414

C495 470pF

DDR01_BA2

DDR0_DQ[13]

C490 0.1uF

75 AR403

A10/AP

VSSQ_5

DDR01_BA0

VDD_4

DDR01_BA1

DDR0_DQ[12]

DDR1_DQ[4]

C489 0.1uF

DDR01_A[10]

DDR0_DQ[11]

B18

C488 0.1uF

DDR01_A[13] DDR01_A[3] AR402

D1.8V H8

C21

C487 0.1uF 75 AR401

004:A4

DDR01_A[0-3,7-13]

A13

DDR0_DQ[6]

B21

C486 0.1uF

DDR01_A[7] DDR1_A[5]

004:A4

75 AR400

CS B7

C485 0.1uF

DDR01_A[0]

F12

C419 10uF 10V

C482 0.047uF

DDR01_A[2]

F11

C425 C417 10uF 10uF 16V 10V

C481 0.1uF

DDR01_RASb

DDR0_DQ[9]

E20

C480 10uF

DDR01_A[0-3,7-13]

DDR0_DQ[10]

F18

C479 470pF

C478 0.047uF

C477 0.1uF

C476 10uF

C475 22uF

C474 10uF

C473 10uF

C472 0.1uF

C471 0.047uF

C469 10uF

C470 470pF

C468 0.1uF

C465 0.047uF

C462 470pF

C461 470pF

C460 0.047uF

C459 0.1uF

C458 10uF

C457 470pF

C456 0.047uF

C455 0.1uF

C454 10uF

C451 22uF

C448 10uF

C447 10uF

C446 0.1uF

C445 0.047uF

DDR0_DQ[2]

C406

C412 0.1uF 16V

E10

0.1uF

C411 0.1uF 16V

004:A7;004:F4 DDR1_CLKb

004:B5 R407 100 1%

DDR01_A[1]

DDR01_A[3] DDR0_A[4]

DDR_VDDP1P8_2

C426 10uF 16V

C444 470pF

C443 10uF

C442 0.1uF

DQ5

DDR0_DQ[1]

D1.8V H8

DDR01_BA0

DDR0_DQ[7]

DQ4 RAS

DDR01_A[0-3,7-13]

DDR01_BA1

DDR0_DQ[8]

DQ2

E15

DQ1

DDR01_BA1 DDR01_A[7-13]

B16

CK CKE

DDR0_DQ[0]

DDR01_BA0

F16

C11

DQ0

DDR1_A[4]

F15

C8 CK

DDR01_BA0

DDR01_A[8]

B14

DDR01_A[0-3]

DDR0_A[5]

E12

DDR0_CLKb

DDR1_DQ[0-7]

DDR0_DQ[0-7] 004:B6 004:A7;004:F4 DDR1_CLK R406 100 1%

DQ3

DDR0_A[4-6]

IC402 NT5TU128M8DE_BD

DDR0_CLK

DDR01_CKE

DDR01_A[0]

E14

F14

C441 0.047uF

C440 470pF

A13 B15

004:A7;004:C4

DDR0_CLK 004:C7;004:C4 DDR0_CLKb 004:C7;004:C4 DDR1_CLK 004:F7;004:F4

C12

C410

DDR01_A03

B12

C400

DDR01_A02

IC400 NT5TU128M8DE_BD

DDR01_ODT

1uF

DDR01_A01

DDR_VTT

240 1%

C23

C401

DDR01_A00

DDR01_CKE

E16

C409

DDR1_CLKB

0 R412

1uF

DDR1_CLK

R411 OPT

C22

470pF

DDR0_CLK DDR0_CLKB

B17

470pF

DDR_EXT_CLK

B23

C408

DDR_COMP DDR01_ODT

F20

C407

DDR01_CKE

1uF

DDR_PLL_LDO

C404

B24

470pF

DDR_PLL_TEST

C403

0.1uF

C405

DDR_BVSS1

0.1uF

A24

C402

DDR_BVSS0

1uF

DDR_BVDD1

470pF

DDR_BVDD0

D1.8V

BCM (EUROBBTV)

HONG YEON HYUK DDR Memory

2009.06.18

COMPONENT1 COMPONENT2 AV1 JK1100 PPJ237-01

+3.3V_NORMAL

[RD1]E-LUG R1101 10K

5C 4C

[RD1]O-SPRING D1100 5.6V

[RD1]CONTACT

[WH1]O-SPRING

[YL1]CONTACT

C1100 100pF 50V

NON_SCART

R1104 AV_CVBS_DET 9:G3

C1101 1uF 25V R1105 D1101 R1102 0 470K 5.6V

C1103 100pF 50V

R1112 10K

REAR_AV_R_IN 10:B5;AF24

SCART1_DET ==> COMP1_DET

DTV/MNT_V_OUT

TP1100

C1112R1116 100pF 50V

D1115 5.6V

TP1101

SC1_FB

TP1102

SC1_ID

TP1103

DTV_ATV_SELECT

TP1104

SCART1_Rout_P

TP1105

SCART1_Rout_N

C1102 1uF

[YL1]O-SPRING

[YL1]E-LUG

D1102 5.6V

D1103 5.1V

[RD2]E-LUG

[RD2]O-SPRING_2

D1116

C1105 47pF 50V

C1114 25V 1uF

REAR_AV_CVBS 11:C4;AL18

SC1_R_IN ==> COMP1_R_IN D1105 5.6V

OPT

D1104 5.6V

[BL2]O-SPRING

[BL2]E-LUG-S

[GN2]CONTACT

[GN2]O-SPRING

6D 6N

[RD3]E-LUG

[RD3]O-SPRING_2

4N 5M 5L

R1113 0

R1108 470K

==> COMP1_L_IN

C1124 100pF

D1106 5.5V

C1108 27pF 50V L1100 270nH

C1120 27pF 50V

D1107 5.5V

C1106 27pF 50V

C1118 27pF 50V

TP1107

SC1_CVBS_IN

TP1108

SC_RE1

TP1109

SC_RE2

TP1110

SCART1_Lout_N

SC1_R

==> COMP1_Pr

TP1111

SCART1_Lout_P

SC1_B

==> COMP1_Pb

SC1_G

==> COMP1_Y

L1101 270nH D1108 5.1V

[GN2]E-LUG

C1125 100pF

L1102 270nH

[RD2]O-SPRING_1 [RD2]E-LUG-S

R1109 470K

SC1_L_IN

[WH2]O-SPRING

R1114 0

D1117 5.1V

C1107 27pF 50V

C1119 27pF 50V

New Item Development EARPHONE BLOCK HP_LOUT OPT C1130 1000pF 50V

[RD3]CONTACT

C OPT Q1100 MMBT3904-(F)

R1121 1K

[RD3]O-SPRING_1

[RD3]E-LUG-S

[BL3]O-SPRING

[GN3]CONTACT

[GN3]O-SPRING

[GN3]E-LUG

COMPONENT2 <Practically COMP1>

JK1101 KJA-PH-0-0177

+3.3V_NORMAL

GND

DETECT

HP_DET

HP_ROUT

+3.3V_NORMAL OPT C1131 1000pF 50V

R1115 10K

OPT Q1101 MMBT3904-(F)

R1122 1K

B B

E OPT MMBT3904-(F) Q1102

+3.5V_ST

COMP2_DET

C1115 100pF 50V

D1109 5.6V

R1124 10K SIDE_HP_MUTE

C1117 25V 1uF +3.3V_NORMAL

D1114 5.6V

R1118 0

R1111 470K

EARPHONE AMP

COMP2_R_IN C1127 100pF

L1106 10uH

C1137 10uF 10V

C1116 25V 1uF

COMP2_L_IN

COMP2_Pb C1122 27pF 50V

COMP2_Y

D1118 5.1V

C1111 27pF 50V

HP_ROUT_N

C1135 1uF 10V

INR-

HP_ROUT_P

L1105 270nH D1113 5.1V

INR+

R1120 4.7K

C1110 27pF 50V

INL+

C1134 1uF 10V

HP_LOUT_P

L1104 270nH D1112 5.5V

INL-

C1133 1uF 10V

C1123 27pF 50V

1/16W

13 12

2 IC1100 TPA6132A2

EAN60724701 5

L1107 BG2012B080TF HP_LOUT C1142 0.22uF 16V +3.3V_NORMAL

VDD 14

R1131 0

HPVDD

C1140 2.2uF 10V

R1129 100K OPT

R1132 OPT 4.7K R1133 0 C

CPP

PGND

Q1104 2SC3052

C1141 2.2uF 10V

R1134 1K SIDE_HP_MUTE

CPN

8 HPVSS

HP_LOUT_N

C1121 27pF 50V

R1126 OPT

C1109 27pF 50V

COMP2_Pr D1111 5.5V

SGND

OUTL C1132 1uF 10V

OUTR

L1103 270nH

C1139 0.1uF 16V

C1136 1uF 10V

Close to the IC

C1126 100pF

R1127 4.7K

R1110 470K

R1117 0

R1128 OPT

D1110 5.6V

E OPT MMBT3904-(F) Q1103

OPT

[BL3]E-LUG-S

R1123 1K

R1119 1K

[WH3]O-SPRING

OPT

[RD2]CONTACT

R1107 0

C1104 100pF 50V

C1113 25V 1uF

R1100

5.1V

25V R1106 R1103 0 470K

OPT

REAR_AV_L_IN 10:B5;AF22

R1125 10K

COMPONENT1 <Practically COMP2>

R1130 0

L1108 BG2012B080TF HP_ROUT

C1138 2.2uF 10V

1/16W

GP2_BCM HP/COMP/REAR AV(NON_EU_CN)

C1143 0.22uF 16V

09/10/19 11

CAN H-NIM/NIM TUNER for TAIWAN TU2600-*1 TDVJ-H031F

TU2600-*5 TDTR-T035F

TU2600-*2 TDVJ-H001F

+5V_TU

Taiwan/Brazil_H Latin_Tuner_H

Latin_Tuner_V 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

ANT_PWR[OPT] 1 BST_CNTL 2 +B 3 NC[RF_AGC] 4 AS 5 SCL 6 SDA 7 NC(IF_TP) 8 SIF 9 NC 10 VIDEO 11 GND 12 1.2V 13 3.3V 14 RESET 15 IF_AGC_CNTL 16 DIF_1 17 DIF_2 18

ANT_PWR[OPT]

BST_CNTL

NC[RF_AGC]

SCL

SDA

NC(IF_TP)

SIF

VIDEO

GND

1.2V

3.3V

RESET

IF_AGC_CNTL

DIF_1

DIF_2

RF_S/W_CTL L2600 BST_CTL

BLM18PG121SN1D

+B1[5V] R2615

NC_1[RF_AGC]

0 NC_2 R2602 SCLT

TU2600 TDTR-T055F

SDAT NC_3 SIF

Taiwan/Brazil_V NC_4

VIDEO GND

+B2[1.2V]

+B3[3.3V] RESET

IF/AGC

DIF_1[N] DIF_2[P]

19 SHIELD

SHIELD

8 9 10

TU2600-*4 TDTJ-S001D

TU2600-*3 TDTJ-S031D

AU_Asia_Tuner_H

AU_Asia_Tuner_V 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

ANT_PWR[OPT]

BST_CNTL

NC[RF_AGC]

SCL

SDA

NC(IF_TP)

SIF

VIDEO

GND

1.2V

3.3V

RESET

IF_AGC_CNTL

DIF_1

DIF_2

ANT_PWR[OPT]

BST_CNTL +B

NC[RF_AGC]

AS SCL

SDA

NC[IF_TP] SIF

VIDEO

R2621

ISA1530AC1 R2618 2.2K

10K

C R2605

+B[5V] R2600

Q2604 2SC3052 C2613 0.01uF 25V

+5V_TU

C2636 22uF 10V

LNA2_CTL/BOSTER_CTL

OPTION : RF AGC

C2604 100pF 50V

C2609 10uF 10V OPT

C2608 0.1uF 16V OPT

C2606 0.1uF 16V

C Q2600 2SC3052 OPT

+5V_TU R2608 10K

R2625 470

IF_AGC_SEL

OPT

L2609-*1 33 NON_TUNER_I2C_LPF L2610-*1 33 NON_TUNER_I2C_LPF

E OPT

R2623 10K

close to TUNER

C2601 0.1uF 16V

NC[RF_AGC]

Q2601

close to TUNER ANT_PWR[OPT] BST_CNTL

RF_SWITCH_CTL

SCL

R2626 82 TU_SIF

B R2622 4.7K

+5V_TU

L2609 270nH TUNER_I2C_LPF

ISA1530AC1 C

Q2605

SCL0_3.3V

SDA

L2610 270nH TUNER_I2C_LPF

TUNER_I2C_LPF

SDA0_3.3V

SIF NC

C2602 0.1uF

close to TUNER

C2639 20pF 50V

C2638 20pF 50V

TUNER_I2C_LPF

close to TUNER

+B3[3.3V] RESET

C2634 10uF 10V

C2603 0.1uF 16V

R2619 200

0 B C

Q2602 ISA1530AC1

+3.3V_TU +3.3V_TU

BLM18PG121SN1D C2600 100pF 50V

R2644

R2614 1K OPT

+1.2V_TU

+B2[1.2V]

R2616 200

TU_CVBS

TUNER_I2C_LPF R2613

L2605

R2643 1K OPT

OPT TUNER_I2C_LPF

16V

VIDEO GND

C2612 62pF 50V

C2611 62pF 50V

C2612-*1 C2611-*1 18pF 18pF 50V 50V NON_TUNER_I2C_LPF NON_TUNER_I2C_LPF

NC(IF_TP)

C2605 100pF 50V

C2607 0.1uF 16V

R2607 100K

R2606 100

C2635 10uF 10V

TUNER_RESET

C2610 0.1uF 16V

IF_AGC_CNTL DIF_1[N]

R2601

IF_AGC

R2611

100

IF_N_EXT

NIM

DIF_2[P] R2612

100 NIM

IF_P_EXT

GND

1.2V 3.3V

SHIELD

INT_DEMOD R2603

INT_DEMOD R2604

TU_IF_N_BCM TU_IF_P_BCM

RESET IF_AGC_CNTL DIF_1 DIF_2

SHIELD

CAUTION : Closed BCM IC(IC100)

IF AGC FILTER

3.9K R2624

1/16W 5%

510

R2638 220

R2641

C2627 0.01uF

3.9K R2632

5% 1/16W

R2633 2K

R2642 510 READY

+5V_NORMAL

TU_IF_AGC_BCM

C2629 0.01uF

5% 1/16W

A3.3V

+3.3V_TU

IC2600

+3.3V_NORMAL

AZ1117H-ADJTRE1(EH11A)

+3.3V_TU L2604 CIC21J501NE

+1.2V_TU

INPUT TU_IF_AGC_1

OUTPUT

60mA

R2628 10

ADJ/GND

C2621 0.1uF 16V

TU_IF_AGC_2 C2614 0.1uF 16V

C2622 0.1uF 16V

C2625 22uF 10V

C2633 0.1uF 16V

GND

R2627 1.2K

For ESD +5V_NORMAL

+5V_TU

IF FILTER OPTION V_OUT=V_REF(1+R2/R1)

R2629 1

C2615 10uF 10V

TU_IF_N_BCM TU_IF_P_BCM

0.01uF 0.01uF

C2631 C2632

L2603

200mA

BLM18PG121SN1D C2616 0.1uF 16V

C2620 0.1uF 16V

C2637 0.1uF 16V

C2623 0.1uF 16V

C2624 10uF 16V

C2626 22uF 10V

TU_IF_N_1 TU_IF_P_1

GP2_BCM Tuner (Half Nim)

Ver. 1.0 28

PANASONIC (ISDB-T) MN884433

+1.2V_DE

ISDB_DEMOD R2807 22

+3.3V_DE

FE_TS_VAL_ERR ISDB_DEMOD R2808 22

ISDB_DEMOD ISDB_DEMOD ISDB_DEMOD ISDB_DEMOD ISDB_DEMOD C2812 C2815 C2816 C2819 C2821 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 16V 16V 16V 16V 16V

FE_TS_SYNC ISDB_DEMOD R2809 22

FE_TS_SERIAL ISDB_DEMOD C2810 0.1uF

ISDB_DEMOD R2810 22

(FE_TS_SERIAL) FE_TS_DATA_CLK

16V

C2802 0.1uF ISDB_DEMOD

C2804

0.1uF

ISDB_DEMOD

TEST2

SCKA

GPI2

SDOA

PCKA

DENA

VDDH_4

VSS_10

HDVPP

RON

NC_3

HDVDDH

NC_4

HDVDDL1

VSS_11

VDDL_7

SCKB

TEST0

SDOB

PCKB

DENB

GPO2

VDDH_5

TEST1 76

VSS_9

INTB

AII_S

INTA

SADR

VDDH_3

VRT_S

SCL

SDA

R2813

VSS_8

R2814

HDVDDL0

SADR_S

NC_2

SADR_T

VDDL_6

VSS_7

VRB_S

TCPO_S

VDDL_1

PSEL

IC2800 MN884433

10 11 12 13

ISDB_DEMOD

AMP_I2C HAVE PULL-UP

2.2K

ISDB_DEMOD C2825

0.1uF SCL1_3.3V SDA1_3.3V

ISDB_DEMOD C2826 0.1uF

ISDB_DEMOD C2827 0.1uF

ISDB_DEMOD C2824

0.1uF

TEST3

NRST

TDI

TCK

VDDL_4

VSS_5

NC_1

SHVDDH

SHVPP

TEST4

GPI0

GPI1

VDDH_2

VSS_4

VDDL_3

GPO0

AGCR_T

AGCI_T

GPO1

VDDH_1

26 VSS_3

MSDA_T

MSCL_T

ISDB_DEMOD R2804 2.2K ISDB_DEMOD R2805 2.2K

OPT R2812

VSS_6

51 48

25 47

AVSS_T

VDDL_5

C2801 0.1uF ISDB_DEMOD

24 45

AIP_T

C2800

ISDB_DEMOD

TRST

0.1uF

TMS

AIN_T

C2808

CSEL0

AVDD_T

ISDB_DEMOD

ISDB_DEMOD ISDB_DEMOD

0.1uF 0.1uF

CSEL1

VRB_T

C2806 C2807

TDO

VRT_T

SYNCA

IR_T

ERRA

SYNCB

VDDL_2

ZSEL

ACKI

ISDB_DEMOD

2.2K

AIQ_S

TCPO_T

0.1uF

ISDB_DEMOD R2800 10K 1%

OPT R2811

AVSS_S

ERRB

C2805

IF_N_EXT IF_P_EXT

VSS_1 AVDD_S

MSCL_S ISDB_DEMOD R2801 2.2K MSDA_S R2802 2.2K VSS_2 ISDB_DEMOD VSSH

C2803 0.1uF ISDB_DEMOD

100

AGC_S

+3.3V_DE

DEMOD_RESET

ISDB_DEMOD C2811 0.1uF 16V

ISDB_DEMOD C2813

ISDB_DEMOD C2823 0.1uF 16V

0.1uF 16V

C2820 C2822 C2817 0.1uF 0.1uF 0.1uF 16V 16V 16V ISDB_DEMOD ISDB_DEMOD ISDB_DEMOD

IF_AGC_ISDB

10K R2803 ISDB_DEMOD ISDB_DEMOD C2809 0.1uF

ISDB_OPT R2806 1M

ISDB_DEMOD C2814 15pF 50V

ISDB_DEMOD X2800 ISDB_DEMOD 25MHz C2818 15pF 50V

GP2_Saturn7M ISDB-T Demodulator

Ver. 1.0 28

Panasonic Demodulator Power(3.3V,1.2V) ISDB_POWER

IC2900 SC4215ISTRT +3.3V_DE

+3.3V_DE

NC_1

GND

+1.2V_DE ISDB_POWER

ISDB_POWER EN

L2900 BLM18PG121SN1D

5.1K C2901 0.1uF

ISDB_POWER C2903 10uF NC_2 10V

NC_3

10K

C2900 0.1uF

C2902 0.1uF 16V

ISDB_POWER

VIN ISDB_POWER

ISDB_POWER

R2903

ADJ

R2902

+3.3V_NORMAL

ISDB_POWER C2904 0.1uF 16V

ISDB_POWER C2905 22uF 16V

IF AGC SELECTION IF_AGC_ISDB

TP2901

IF_AGC_SEL

R2900 0 ISDB_DEMOD IF_AGC R2901 0 INT_DEMOD

TU_IF_AGC_BCM

GP2_Saturn7M Demodulator

Ver. 1.0 29

USB2 OPTION USB / DVR Ready

+3.3V_NORMAL

IC2202

+5V_USB

AP2191SG-13

120-ohm C2218

SIDE_USB_DM

C2206 1uF 10V

SIDE_USB_DP

L2202 MLB-201209-0120P-N2

NC 8 OUT_2 7

2 IN_1

OUT_1 6

3 IN_2

FLG 5

100uF 16V

C2203 0.1uF

C2204 0.1uF

C2205 0.1uF

RESET_N

0.1uF R2209 100K OPT R2210 100K

USBDN2_DP

SCL/SMBCLK/CFG_SEL0

VDDA33_1

VDD33

SDA/SMBDATA/NON_REM1

NC_2

NC_8

C2213

USB IC2203

R2211

100K OPT

R2213

100K OPT

L2203 MLB-201209-0120P-N2 120-ohm C2219

R2207 OPT R2208

OPT

SCL2_3.3V SDA2_3.3V

KJA-UB-4-0004 JK2202

100uF 16V

NC 8

1 GND

+5V_USB

OUT_2 7

2 IN_1

OUT_1 6

3 IN_2

FLG 5

R2221 4.7K OPT

4 EN

R2223 2.7K

EAN60921001

C2221 10uF 10V

C2223 0.1uF

USB_CTL2 +3.3V_USB

C2214 4.7uF

R2227

/USB_OCD2 040:J6

USB_DM2

USB_DP2

D2202 CDS3C05HDMI1 5.6V

D2204 CDS3C05HDMI1 5.6V

/USB_OCD2

USB_CTL2

1uF 10V

C2209 /USB_OCD1

USB_CTL1

+3.3V_NORMAL

100K OPT

0.1uF

R2206 100K

0 R2205 100K

18 NC_5

17 OCS2_N

16 PRTPWR2

VDD33CR

C2211 0.1uF

VDD18

OCS1_N

12 PRTPWR1

11 TEST

D2203 CDS3C05HDMI1 5.6V

+3.3V_USB

USB DOWN STREAM

VDDA33_2

NC_6 R2204 100K

/RST_HUB

NC_7 0

NC_4

D2201 CDS3C05HDMI1 5.6V

AP2191SG-13

R2214 0 C2215 0.1uF OPT R2212

NC_1

NC_3

2 4 5

100K

R2203

VBUS_DET

HS_IND/CFG_SEL1

IC2201

USB_DP1

C2212 27

USB2512A_AEZG

1 VDDA33_3 29

USBUP_DM 30

USBUP_DP 31

XTAL2

XTAL1/CLKIN 33

SUSP_IND/LOCAL_PWR/NON_REM0

1/10W 1% VDD18PLL

RBIAS

VDD33PLL

THERMAL 37

USB_DM1

C2202 0.1uF

C2222 0.1uF

/USB_OCD1

C2201 1uF 10V

C2220 10uF 10V

USB_CTL1

USB_DP2

1 2

R2226 2.7K

+3.3V_USB

USBDN2_DM

USB_DM2

X2201 24MHz

C2208 15pF C2210 15pF

0.1uF

C2207 USB_DP1

R2202 1M 1%

R2201 12K

USBDN1_DP

VSS +3.3V_USB

USBDN1_DM

USB_DM1

4 EN

KJA-UB-4-0004 JK2201

USB DOWN STREAM

+3.3V_USB

R2220 4.7K OPT

EAN60921001

R2225

+3.3V_NORMAL L2201 BLM18PG121SN1D

1 GND

+3.3V_NORMAL

BLUETOOTH

C1898 1uF BCM BT MODULER1886 BCM BT MODULE R1887 47K 47K

R1888 4.7K B

BT_ON/OFF

BCM BT MODULE

C 500 L1899 OPT

D BCM BT MODULE Q1801 RTR030P02

BLUETOOTH FOR BCM

10 R1889

BCM BT MODULE

2SC3052 Q1800 BCM BT MODULE

11 10 BCM BT MODULE C1899 22uF 10V R1896 27

BT_DM

D1899 CDS3C05HDMI1 5.6V BCM BT MODULE

BCM BT MODULE

R1897 27 BT_DP

D1898 CDS3C05HDMI1BCM BT MODULE 5.6V BCM BT MODULE R1898 0 BT_RESET

4 BCM BT MODULE 3 R1899 0

VREG_CTRL

2 BCM BT MODULE 1

12507WR-10L P1895 BCM BT MODULE

CI POWER ENABLE CONTROL

CI CONTROL BUFFER /CI_SEL

CI_A[0] CI_A[1]

EBI_CS

CI_A[2] CI_A[3]

EBI_WE

CI_A[4] CI_5V_CTL

CI_A[5]

007:H7

CI_A[6]

[GP27]

CI_A[7]

CI_A[8] CI_A[9] CI_A[10] CI_A[11]

CI_A[12] CI_A[13]

CI_A[0-13]

007:E6

EBI_RW

CI_A[14]

/CI_CD1

CI_OUTCLK,CI_OUTDATA[0-7],CI_OUTSTART,CI_OUTVALID

CI_OUTDATA[4] CI_OUTDATA[5]

DVB-CI PULL-DOWN (Near CI Slot)

CI_OUTDATA[6] CI_OUTDATA[7]

CI_OUTCLK CI_OUTVALID CI_OUTSTART

/CI_IREQ [GP39] 007:H5;016:AJ3

CI_OUTDATA[0] CI_OUTDATA[1] CI_OUTDATA[2] CI_OUTDATA[3]

DVB-CI PULL-UP (Near CI Slot)

CI_MOD_RESET [GP49] /CI_WAIT

/CI_WAIT CI_OUTCLK /CI_CD1 /CI_CD2 [GP38] /CI_CD2 CI_MOD_RESET

FE_TS_SYNC FE_TS_VAL_ERR FE_TS_DATA_CLK

High_Common(BCM3556)

Non_CI

2009.10.19 46

G5111 120Hz MINI_LVDS

GMA6

GMA7

GMA9

GMA10

0 NON_GIP

GND

GMA1

Z_OUT

GMA3

CLK1

GMA4

CLK2

GMA6

CLK3

R7512

GMA7

CLK4

R7513

GMA9

CLK5

GMA10

CLK6

0 MINI_LVDS

R7511

VGI_N

VGI_P

VGH_ODD

VDD_ODD

VGH_EVEN

VSS

VST

GND

VCOM_FB

VCOMRFB

GVST_I/GSP

VCOM_IN

VCOMR

POL

GND

SOE

VDD

LLV0P

HALF_VDD

LLV0N

HALF_VDD

GND

VCC

GND

RV0+

RV0-

RV1+

RRXB3+/RLV1P

RV1-

RRXB3-/RLV1N

RV2+

RV2-

RRXBCK-/RLV2N

RVCLK+

RRXB0+/RLCLKP

RVCLK-

RV3+

RRXA4+/RLV3P

RV3-

RRXA4-/RLV3N

GMA12 GMA13

GMA13

GMA15

GMA16

GMA18

GND

OPT_N

H_CONV

VST_IN

POL

SOE

GND

LV0+

LV0-

LV1+

LLV1P

LV1-

LLV1N

LV2+

LLV2P

LV2-

LLV2N

LVCLK+

LLCLKP

LVCLK-

LLCLKN

LV3+

LLV3P

LV3-

LLV3N

LV4+

LV4-

LLV4N

LV5+

LLV5P

LV5-

GND

VCC

GMA12

VCC_LCM

R7518 510 OPT

R7519 0 OPT_N

MINI_LVDS

H_CONV

VCC_LCM

C7502 0.01uF 50V MINI_LVDS

C7500 0.1uF 16V MINI_LVDS

VDD_LCM To reduce Audible noise (2012) HVDD

LLV4P

C7503 1uF 50V C7501 10uF 16V MINI_LVDS

LLV5N

C7504 0.1uF 50V MINI_LVDS

MINI_LVDS

RRXB4-/RLV0N

RRXACK+/RLV4P RRXACK-/RLV4N

HALF_VDD

RV5+

RRXA2+/RLV5P

HALF_VDD

RV5-

RRXA2-/RLV5N

VDD

GND

VDD

SOE

GND

POL

VCOM_IN

VCOML

VST_IN

GVST_I/GSP

VCOM_FB

VCOMLFB

H_CONV

GND

OPT_N

VST

GND

VSS

GMA18

VGH_EVEN

VDD_EVEN

GMA16

VGH_ODD

VDD_ODD

GMA15

VGI_P

GMA13

VGI_N

GMA12

CLK6

GMA10

CLK5

GMA9

CLK4

GMA7

CLK3

GMA6

CLK2

GMA4

CLK1

GMA3

Z_OUT

GMA1

GND

CLK3 CLK2

R7503

0 NON_GIP

OPT_N

C7505 0.1uF 16V MINI_LVDS

C7507 0.01uF 50V MINI_LVDS

RRXA0RRXA1+ RRXA1RRXA3+ RRXA3RRXB1+ RRXB1RRXB2+

RRXB0-/RLCLKN

RV4-

0 GIP

C7509 10uF 16V MINI_LVDS

RRXBCK+/RLV2P

RV4+

R7500

C7508 0.1uF 50V MINI_LVDS HVDD

RRXA0+ RRXB4+/RLV0P

0 GIP

VDD_LCM

VCC_LCM

0 NON_GIP

VGL (-5V)

MINI_LVDS

GND

R7502

To reduce Audible noise (2012) C7506 1uF 50V

VCC

VST

GVDD_ODD_I/GSC GVDD_EVEN_I/GOE

0 NON_GIP 0 NON_GIP

R7516 R7517

VST

VGL_I

0 NON_GIP 0 NON_GIP

R7515

0 GIP

VGL (-5V)

0 NON_GIP 0 NON_GIP

VGL_I

VDD_EVEN R7508

VGH_M (+25V)

Z_OUT

R7514

9 10

R7501

GCLK4/OPT_P

R7509

GMA4

R7507

GMA3

R7506

GMA1

R7505

R7510 R7504

GND

RRXB2OPC_EN OPC_OUT

VCC_LCM

R7520 510 OPT

R7521 0 OPT_N

MINI_LVDS

GMA15

GMA6

0 NON_GIP

TM240Hz

0 NON_GIP

P7501 104060-6017

TM240Hz

0 NON_GIP

P7500 104060-6017

0 NON_GIP

[Right FFC Connector] (60Pin Mini-LVDS)

[LEFT FFC Connector] (60Pin Mini-LVDS)

[To MASTER LED DRIVER] P7900 12507WR-10L IOP

L_VS

M0_MOSI

M0_SCLK +3.3V_NORMAL

M1_MOSI

M1_SCLK R7907 3.3K Edge

R7908 3.3K Edge

R7909 3.3K Edge

R7904 22 IOP

S_CS_N

R7905 22 IOP

S_MOSI

R7906 22 IOP

S_SCLK C7903 100pF 50V

C7901 100pF 50V

C7907 100pF 50V

OPT

C7905 100pF 50V

C7909 100pF 50V

C7911 100pF 50V

OPT

C7913 100pF 50V OPT

OPT

C7914 100pF 50V OPT

[To SLAVE LED DRIVER] P7901 12507WR-08L Except Edge(42/47")

1 R7900 2

R7901 22 Edge(55") R7902

R7910

IOP

R7911

IOP

R7912

22 Edge(55")

R7913

R7914

22 Edge(55")

R7918

IOP

R_VS

22 OPT

22 IOP

IOP

R7916 22 Edge(55")

R7919

R7917 22 Edge(55")

R7915

22 Edge(55")

M2_MOSI M2_SCLK M2_SCLK

M2_MOSI

M3_MOSI

M3_SCLK

R_VS

9 R7903 22 IOP

C7900 100pF 50V OPT

C7902 100pF 50V OPT

C7904 100pF 50V OPT

C7906 100pF 50V OPT

C7908 100pF 50V OPT

C7910 100pF 50V OPT

C7912 100pF 50V OPT

GP2_Saturn7M Interface for LG5111

Ver. 1.0 72

FROM LIPS & POWER B/D

3.5V

GND

GND/V-sync

12V

INV ON

12V

A.DIM

12V

P.DIM1

GND/P.DIM2

Err OUT

C8028 10uF 25V

COMP

C8047 22uF 10V

C8066 10uF 16V

NON_PD_+3.5V R8064 5.1K

R8067 14K

PD_+3.5V 1%

OPT R8075 10K R8081 100

RESET

POWER_DET

GND ESD C8065 0.1uF 16V

R8079 100K

+24V

+3.5V_ST

C8049 0.1uF 16V

not to RESET at 8kV ESD

IC8008 OPT R8080 14K 1%

OPT C8046 100pF 50V

Vout=0.8*(1+R1/R2)

Q8005 2SC3052

POWER 18.5V R8061-*2 22K 1%

POWER 24V R8061-*1 24K 1%

POWER 20V R8061 24K 1%

NCP803SN293 VCC

R8074 100

RESET

BCM core 1.2V volt

A_DIM

LGD_IOP A_DIM_LGD

R8044 10K ESD D8000 5.6V

PGND_1

ERROR_OUT

R8045

0 NON_ESD R8043

EN/SYNC

PGND_2

L8009 2uH

IC8001 SW_1

C8069 0.1uF NON_LED_MODEL

SW_2

MAX 2.3A

A1.2V

D1.2V

R8060 R8046

R8048

POWER_ON/OFF2_2 L8013

30K 1%

470K 1%

910K 1%

L8011 BLM18PG121SN1D

L8006 C8027 0.1uF

MLB-201209-0120P-N2

PANEL_POWER

IN_2

C8036 0.1uF

POK

R8040

VCC

100K R8041

C8037 22uF 10V

R8042 0

MP2208DL-LF-Z

C8043 10uF 16V

C8041 22uF 10V

C8045 0.1uF 16V

C8051 0.1uF

50V

C8052 22uF 25V

COMP

C8032 0.1uF

C8033 1uF 10V

IC8005

AOZ1024DI 5

R8058 20K C8054 2200pF 50V

C8029 22uF 16V

D3.3V

L8016 CIC21J501NE

L8015 3.6uH

VIN IN_1

+3.3V_NORMAL

10K

CIC21J501NE

R8069 27K

NON_LED_MODEL R8037 4.7K

C8026 0.1uF

AGND

OPC_OUT

+3.3V_NORMAL +12V

ESD R8045-*1 100K

R8070 4.7K

R8034 0 HD_OPC

MAX 3.1A POWER_ON/OFF2_1

PWM_DIM

R8033 0 SCAN_BLK1/OPC_OUT SCAN/FHD_OPC

C8021 1uF 25V OPT

R8071 10K

R8027 0 PWM_NON_OPC

OPT

C8017 0.1uF OPT

GND

R8031 0

R8022 0

POWER 20V R8062 5.1K 5%

3.9K R8066

CMO_PSU

POWER 24V R8062-*1 4.3K 1%

R8039 10K OPT

R8029 0

AUO_PSU R8030

POWER 18.5V R8062-*2 4.7K 1%

+12V

C8057 C8059 22uF 22uF 10V 10V

C8067 10uF 10V

C8064 0.1uF 16V

C8063 0.1uF 16V

C8035 22uF

Vout=0.8*(1+R1/R2) D

Q8004 AO3407A

S R8010 10K

INV_CTL

+3.5V_ST

C8013 4.7uF 50V

PANEL_VCC G

R8011 1.8K

OPT C8015 1uF 25V

C Q8003 2SC3052

B C R8008 22K

Q8001 2SC3052

C8022 0.1uF 50V

BCM DDR 1.8V

Max 1100 mA

A2.5V

+3.3V_NORMAL

1:AK10 E

+3.5V_ST

A2.5V

D1.8V IC8004 SC4215ISTRT

BST

+12V

+5V_USB

L8001 500

IC8000 MP8706EN-C247-LF-Z

LX Placed on SMD-TOP PGND C IN

C8002 10uF 25V

SW_2 C8007 0.1uF

BST

R8006 22

OPT C8016 100pF 50V

C8014 1uF 50V

VCC

R8012 10K

EN/SYNC

POWER_ON/OFF2_1 R8013 10K

R8016 33K

OPT C8019 100pF 50V

C8020 22uF 10V

C8023 0.1uF 16V

C8025 0.1uF 16V

C8031 22uF 10V

SGND

500 L8014

R8059 10K

RUN

10K R8052

NC_1

VOUT : 2.533V

GND

R8073 18K R2 1%

ADJ

R8072 39K R1 1%

POWER_ON/OFF1 VREF C8042 0.01uF 25V

COMP

FB C8039 3300pF 50V

C8038 0.01uF 25V

R8051 6.8K

OPT 50V 100pF C8044 R2 R8056 10K 1/10W 1%

C8053 10uF 16V R1 R8057

VIN C8055 0.1uF

4 OPT C8056 0.1uF

NC_2

NC_3

C8058 10uF 16V

C8061 10uF 16V

Placed on SMD-TOP

10K 1% C8048 22uF 10V

C8050 0.1uF

Vout=0.8*(1+R1/R2)

SW_1

GND

R8017 6.2K

NR8040T3R6N

IC8002 MP2108DQ

VIN

MAX 1500mA

L8012 3.6uH

Replaced Part

C8034 0.01uF 25V

L8008

+5V_USB

CIC21J501NE

Vout=0.9*(1+R1/R2)

500 L8017

PANEL_CTL

2 1

OPT

R8025 0 NON_LED_MODEL

R8001 47K B

POWER_ON/OFF2_2

R8050 10K

C8030 10uF 25V

12K 2200pF R8049 C8040

R8032 10K

6.8K

L8000 CIC21J501NE

LX_1

0 C8012 1uF 25V OPT

SCAN_BLK2

C R8023

CMO_PSU

R8021 AUO_PSU/SHARP_PSU_60 0

VIN C8068 0.1uF 16V AGND

R8035 0 +3.3V_NORMAL

OPT R8002 10K

R8024 0 AUO_PSU/SHARP_PSU_52_60

R8003 22K

LX_2

NCP803SN293 VCC

PGND

P8001

C8010 10uF 25V OPT

+3.5V_ST

R8068 100K IC8007

400Hz_MO_SCLK/42_47_LOCAL DIMMING R8077 0 M2_SCLK R8028 0 MO_SCLK 400Hz_MO_SCLK V_SYNC

+3.3V_NORMAL R8026 1K

R8018 100

R8020 NON_SCAN_PSU 0

C8009 0.1uF 50V

L8010 3.6uH

R8053 47K

NON_CMO R8019 100

SCAN_PSU

C8008 0.01uF 25V

PGND

Power_DET

AGND

C8011 0.1uF 16V OPT

R8085 0

SCAN_LIPS

SCAN

R8009 0

0 R8007

L8007 CIC21J501NE

+5V_NORMAL

+3.5V_ST

NR8040T3R6N R8082

400Hz_VSYNC

SMAW200-H24S2

R8084 0

R_VS 400Hz_VSYNC R8036 L_VS 0

SLIM_32~52 NON_SCAN_LIPS

400Hz_MD_MDSI/42_47_LOCAL DIMMING R8076 0 M2_MOSI

MO_MOSI

C8005 0.1uF 50V

400Hz_MD_MDSI R8005 0

C8003 0.1uF 50V

GND

+12V

C8001 100uF 25V

C8018 0.1uF 50V

3.5V

GND GND

IC8003 AOZ1072AI

R8054 5.6K

6 8

MAX 350mA

5 7

C8024 68uF 35V

+12V

ST_3.5V-->3.5V

R8055 10K

GND

3.5V C8006 0.1uF 16V

L8002 MLB-201209-0120P-N2

24V

C8004 0.1uF 16V

GND 3.5V

C8000 100uF 16V

24V

400Hz_VSYNC/42_47_LOCAL DIMMING R8078 0

3.9K

L8003 MLB-201209-0120P-N2

R8083

+3.5V_ST

PWR ON 1 24V 3

L8005 MLB-201209-0120P-N2

OPT R8047

+5V_NORMAL

2 Q8000 2SC3052

SCAN_PSU

LD R8015 0

R8000 10K

+12V

12V-->3.58V

+24V

NORMAL_26~52 P8000 FW20020-24S

R8014

RL_ON

SHARP_PSU_26_32_52

R8004 4.7K

15V-->3.6V 20V-->3.5V 24V-->3.48V

R8063 12K

Q8002

PD_+12V 1%

RT1P141C-T112

1/16W 5%

L_VS R_VS MO_SCLK M2_SCLK MO_MOSI M2_MOSI

THERMAL

+3.5V_ST

R2 L8004 3.6uH

+5V_USB

NR8040T3R6N

Vout=(1+R1/R2)*0.8

BCM (EUROBBTV) POWER

C8062 0.1uF

FLMD0 GND

10K

OPT

50V 15pF C8102

10MHz X8100

R8143

47K

MICOM_DOWNLOAD

R8146

50V 15pF C8106 X8101 32.768KHz

OPT

MICOM_XTAL_DAISHINKU R8175

P123/XT1

P124/XT2/EXCLKS

RESET

P40

P41

P120/INTP0/EXLVI

OCD1B

R8104 10K

+3.5V_ST

R8105

10K

R8107

10K

P61/SDA0

P00/TI000

R8188

P62/EXSCL0

P01/TI010/TO00

R8189

10K

P63

P130

R8192

P20/ANI0

R8194

ANI1/P21

R8195

ANI2/P22

R8196

ANI3/P23

R8190

R8193

NEC_EEPROM_SDA

OPT R8126

NEC_ISP_Rx

R8129

P33/TI51/TO51/INTP4

R8130

P75

R8131

P74

HDMI_CEC

OCD1A

OCD1B

AMP_MUTE

+3.5V_ST

P73/KR3

P72/KR2

ANI4/P24

P71/KR1

ANI5/P25

P70/KR0

ANI6/P26

ANI7/P27

R8191

SIDE_HP_MUTE KEY2 KEY1

LCD/PDP R8124 10K

PWM_LED R8121 10K

TACT_KEY R8112 10K

LCD/OLED R8110 10K

MODEL1_OPT_3

MODEL_OPT_2

TOUCH_KEY

MODEL_OPT_3

PDP/3D

LCD/OLED

LCD

PDP

OLED

MODEL_OPT_0

MODEL_OPT_3

LOW

LOW_SMALL

TBD

HIGH

MODEL_OPT_1

MODEL_OPT_2

AVSS

C8107 1uF

P10/SCK10/TXD0 22 R8179

AVREF

P11/SL10/RXD0 22 R8177

P12/SO10

P13/TXD6

P14/RXD6

P15/TOH0

P16/TOH1/INTP5

P30/INTP1

TACT_KEY

+3.5V_ST

FOR ATSC Assy SCART1_MUTE

TP8100

+3.5V_ST

R8181

10K OPT

R8182

10K OPT

R8183

10K OPT

NEC_TXD

PWM_LED

NEC_RXD

LOGO_BUZZ

POWER_ON/OFF2_2

MODEL1_OPT_2

R8176

MODEL_OPT_1

MODEL1_OPT_1

OPC

NEC_ISP_Tx

LCD/PDP

NEC_ISP_Rx

LOW

OLED/3D

HIGH

R8145

PIN NO.

PIN NAME MODEL_OPT_0

TACT_KEY

OLED/3D R8123 10K

MODEL1_OPT_0

LED_R/BUZZ

100 100

LED_B/LG_LOGO

OPC_EN

100

R8103 R8101

MODEL OPTION

OCD1A

PANEL_CTL

R8102

LOGO_BUZZ R8120 10K

PDP/3D R8109 10K AMP_RESET_N

TOUCH_KEY R8111 10K

+3.5V_ST

MICOM MODEL OPTION

NEC_EEPROM_SDA 22

R8144

R8114

POWER_DET

SDA

P17/TI50/TO50

P31/INTP2/OCD1A

NEC_EEPROM_SCL

22 NON_M-REMOTE

R8117 22

VSS

MODEL1_OPT_3 MODEL1_OPT_2

NON_M-REMOTE

R8142

SCL

0.1uF

C8100

R8122 4.7K

FLASH_WP

POWER_ON/OFF1

R8135

P32/INTP3/OCD1B

22 22

MICOM_DOWNLOAD

R8134

RL_ON

VCC R8125 4.7K

R8100 47K

NEC_MICOM

R8136 OCD1B

UPD78F0513AGA-GAM-AX

WIRELESS_SW_CTRL

R8133

MODEL1_OPT_1

IC8100 M24C16-WMN6T

IC8101

R8187

SCART1_MUTE

R8132

INV_CTL

NC/E2

R8178

NEC_EEPROM_SCL

EEPROM for Micom

NC/E1

Q8100 2SC3052 E

SOC_RESET

EDID_WP C B

R8128

MODEL1_OPT_0

20K

1/16W 1%

R8127

POWER_ON/OFF2_1

NC/E0

R8186

P140/PCL/INTP6

NEC_ISP_Tx

10K R8106

+3.5V_ST 10K

P60/SCL0

SCL1_3.3V SDA1_3.3V R8108

FLMD0

R8119

R8118

OCD1A

C8108 0.1uF

1/16W 1%

FLMD0 43

R8116

NEC_ISP_Tx

NEC_ISP_Rx

SW8100 JTP-1127WEM

R8185 20K

P122/X2/EXCLK/OCD0B 44

R8115

47K

P121/X1/OCD0A 45

0.1uF

MICOM_RESET

R8113

C8104

R8184

REGC 46

+3.5V_ST

VSS 47

12505WS-12A00

C8103 0.1uF

VDD 48

GND

for Debugger +3.5V_ST

R8180

4.7M

+3.5V_ST

P8100

+3.5V_ST

50V 15pF C8105

R8139 10K

WIRELESS_DETECT

0 R8138

WIRELESS_PWR_EN

MICOM_XTAL_EPSON X8101-*1 32.768KHz

MICOM_RESET

50V 15pF C8101

R8140

10Mhz Crystal Ready

+3.5V_ST

GP2_Saturn7M MICOM

Ver. 1.4 5

+3.5V_ST

IR & KEY

EYEQ R8225 100

NEC_EEPROM_SCL

D8204 CDS3C05HDMI1 5.6V

R8213 10K 1%

R8211 10K 1%

L8200 BLM18PG121SN1D

R8209 100

1 EYEQ R8226 100

KEY1 L8201 BLM18PG121SN1D

R8210 100

P8200 12507WR-12L

C8213 1000pF 50V OPT

D8201 5.6V AMOTECH

KEY2 C8206 0.1uF

NEC_EEPROM_SDA D8205 CDS3C05HDMI1 5.6V

C8214 1000pF 50V OPT

C8207 0.1uF D8200 5.6V AMOTECH

+3.5V_ST +3.5V_ST

5 L8202 BLM18PG121SN1D +3.5V_ST

R8202 47K R8200 22

+3.5V_ST

R8204 47K

IR Q8200 2SC3052

C8208 0.1uF 16V

C8209 1000pF 50V

R8227 LED_B/LG_LOGO

B E

R8205 47K

TACT_KEY

R8203 10K

1.5K R8287

10K LD650/LD750

R8206 3.3K OPT

R8224 100

B Q8201 2SC3052

E +3.5V_ST

COMMERCIAL R8201 0

L8203 BLM18PG121SN1D

R8276 R8218 47K R8216 COMMERCIAL 10K

IR_OUT COMMERCIAL C

Q8202 2SC3052 COMMERCIAL_EU

+3.5V_ST

R8214 47K R8207 COMMERCIAL_EU 22

OPT

D8206 5.6V AMOTECH

C8212 100pF 50V

+3.3V_NORMAL

C8210 0.1uF 16V

LED_R/BUZZ C8211 1000pF 50V

1.5K

B E COMMERCIAL_EU

12 OPT R8280 10K

R8220 47K

ETHERNET CONNECT

B Q8204 2SC3052 COMMERCIAL

COMMERCIAL

A2.5V

L8204 JK8200

CIC21J501NE

XRJV-01V-D12-180

R8212 0 COMMERCIAL_US

R8283 0

Zener Diode is close to wafer

R8284 0

Q8203 2SC3052 WIRELESS

R8217 10K

WIRELESS

5.6V

D8212

OPT C8222 10pF 50V

B E

EPHY_RDN

R8221 47K

C Q8205 2SC3052 WIRELESS

C8216 1000pF 50V

R8286 0

B E

OPT C8221 10pF 50V

R8219 47K WIRELESS

WIRELESS

5.6V

WIRELESS

OPT C8220 10pF 50V

D8209

IR_PASS

R8285 0

D8208

R8208 22

EPHY_RDP

5.6V

EPHY_TDN +3.5V_ST

R8215 47K WIRELESS

5.6V D8207

OPT C8218 10pF 50V

+3.5V_ST

WIRELESS

EPHY_TDP

C8217

1000pF 8 D3.3V R8281

510

R8282

510

D2 5.6V

5.6V

D4 D8211

D8210

EPHY_LINK

EPHY_ACTIVITY

RS232C 10 +3.5V_ST

5 9

OPT IR_OUT

R8279 0 R8277 100

8 3

C8200 0.33uF IC8200

C1+ C8201 0.1uF C8202 0.1uF

V+

C2-

VC8204 0.1uF

2 D8202 CDS3C30GTH 30V

VCC

D8203 CDS3C30GTH 30V

GND +3.5V_ST

C1-

C2+ C8203 0.1uF

R8278 100

C8205 0.1uF

MAX3232CDR

DOUT2

SPG09-DB-009

DOUT1

RIN1

JK8201 R8222 4.7K OPT

R8223 4.7K OPT

ROUT1

R8273 0

DIN1

R8274 0

BCM_RXD1 NEC_RXD

DIN2 R8272 0 BCM_TXD1

RIN2

ROUT2 R8275 0 NEC_TXD

EAN41348201

Trace impedance : 100 ohm differenctial impedance to GND plane 5 mils trace width with 7 mils air gap on P/N pair. Adjacent TX/RX differential pairs should be separated by more than 15 mils to each other

* HDMI CEC E

2 1

14 CEC_REMOTE

CKCK-_HDMI1 CK_GND CK+ CK+_HDMI1 D0D0-_HDMI1 D0_GND

12 11 JK830310 9 8

D0+

D0+_HDMI1 D1-

D1-_HDMI1 D1_GND

D1+

D1+_HDMI1 D2-

D2-_HDMI1 D2_GND

D2+

D2+_HDMI1

CE_REMOTE

R8318 0

R8326 22K

DDC_SDA_4 DDC_SCL_4 GND

JP8307

D8312 CEC_REMOTE

MMBD301LT1G

CK-_HDMI4 CK_GND CEC_REMOTE

HDMI_CEC

GND

CK+

CK+_HDMI4 D0D0-_HDMI4 D0_GND D0+ D0+_HDMI4 D1D1-_HDMI4 D1_GND D1+ D1+_HDMI4 D2-

+3.3V_HDMI

D2-_HDMI4 D2_GND D2+ D2+_HDMI4

GND

UI_HW_PORT1

GND

D8311 5.5V ESD

JP8306

CK-

KJA-ET-0-0032

YKF45-7058V

R8317 0

SIDE_HDMI_PORT4

C8311

4 3

GND

DDC_CLK

C8310 0.1uF

JP8305

CE_REMOTE

GND DDC_DATA

C8309 0.1uF

C8324 0.1uF

+3.5V_ST

C8308 0.1uF

DDC_SCL_1

R8308 0

5V_HDMI_4

100K R8349

DDC_CLK

5V_HPD4

C8307 0.1uF

JP8304

+3.3V_HDMI

L8300 BLM18PG121SN1D

C8305 0.1uF

B R8321 4.7K

0.1uF

EAG59023302

12 11 JK830210

D8305 5.5V OPT

DDC_SDA_1

HDMI_HPD_4

KRC104S Q8307

D B S Q8308 BSS83

18 R8307 0

KRC104S Q8306

R8316

HP_DET

GND DDC_DATA

GND

5V_HDMI_1

GND

5V_HPD1

C B

EAG42463001

KRC104S Q8302

R8302

HP_DET 19 18

GND

D8308 5.5V ESD

5.6V ESD

GND

+3.3V_NORMAL

JACK_GND HDMI_HPD_1 B R8311 4.7K

5.6V D8314 CDS3C05HDMI1

SHIELD

KRC104S Q8305

ESD D8313 CDS3C05HDMI1

D8302 5.5V OPT

CE_REMOTE

R8331

R8332

R8333

R8334

5V_HDMI_1

D1_GND

47K C8302 0.1uF 16V

DDC_SDA_4 DDC_SCL_4

OPT R8328

DDC_SCL_3 D2+_HDMI2

VSS_2

VDDDC[1V8]_1

RXA_HPD

DDC_SDA_4

HDMI_HPD_4

CK+_HDMI4

CK-_HDMI4

DDC_SCL_4

D0+_HDMI4 D0-_HDMI4

0 OPT

RXD_HPD

RXD_5V

RXD_DDC_DAT

RXD_DDC_CLK

RXD_C-

RXD_C+

VDDH[3V3]_7

RXD_D0-

RXD_D0+

VSS_10

RXD_D1-

RXD_D1+

VDDH[3V3]_8

RXD_D2-

RXD_D2+

VDDDC[1V8]_3

VSS_11

OUT_D2+

OUT_D2-

RXC_D0-

VDDH[3V3]_5

DDC_SCL_1 CK-_HDMI1

RXA_C-

RXC_C+

RXA_C+

RXC_C-

VDDH[3V3]_1

RXC_DDC_CLK

RXA_D0D0-_HDMI1

RXC_DDC_DAT

RXA_D0+

RXC_5V

D0+_HDMI1

VSS_3

RXC_HPD

RXA_D1D1-_HDMI1

CEC

RXA_D1+

VSS_7

D1+_HDMI1

VDDH[3V3]_2

VDDS[3V3]

50 I2C_SCL

I2C_SDA

R8336 0 TEST2

VDDDC[1V8]_4

VSS_6

RXB_D2+

CDEC_DDC

RXB_D2-

RXB_D1+

VSS_5

RXB_D1-

RXB_D0+

RXB_D0-

VDDH[3V3]_4

VDDDC[1V8]_2

DDC_CLK

RXB_C+

R8327 C8300 0.1uF

VDDH[3V3]_3

DDC_SDA_3

RXB_C-

D8304 5.5V OPT

JP8302

RXB_DDC_CLK

R8305 0

D0+_HDMI3 D0-_HDMI3 CK+_HDMI3 CK-_HDMI3 DDC_SCL_3 DDC_SDA_3 HDMI_HPD_3 Ready for TDA19997 +3.3V_HDMI R8346

OPT

OPT R8347 4.7K OPT

C8315 0.1uF

RXE_DDC_CLK

51 48

25 47

AUX_5V

5V_HDMI_3

RXE_DDC_DAT

INT_N/MUTE

52 44

24 43

RXA_D2+ VDDH[1V8]_1

D2-_HDMI1 D2+_HDMI1

D1+_HDMI3 D1-_HDMI3

R8345 0 OPT

CDEC_STBY

4.7K R8348

0 OPT R8343

DDC_SCL_3 R8306 0

JP8303

GND

C8313 0.1uF 16V

CE_REMOTE CEC_REMOTE CKCK-_HDMI3 CK_GND

5V_HDMI_2

+1.8V_HDMI

CK+

C8314 0.1uF 16V

CK+_HDMI3 C8301 0.1uF 16V

C8303 0.1uF 16V

C8304 0.1uF 16V

D0+ D0+_HDMI3

R8340 22

D0-_HDMI3 D0_GND

R8338 22

C8306 0.1uF 16V

D0-

R8337 0

D1D1-_HDMI3 D1_GND D1+ D1+_HDMI3 D2D2-_HDMI3 D2_GND D2+

HDMI2 D2+_HDMI3

SDA2_3.3V

VDDO[1V8]

D2+_HDMI3 D2-_HDMI3

SCL2_3.3V

RXC_D0+

RXA_D2-

C8317 0.1uF 16V

D2-_HDMI2 D2+_HDMI2

4 3

D1+_HDMI2

TDA19997

RXA_5V

D1-_HDMI2

VSS_8

D0+_HDMI2

RXC_D1-

D0-_HDMI2

RXC_D1+

CK+_HDMI2

IC8300

RXA_DDC_CLK

DDC_SCL_2 CK-_HDMI2

11 JK830110

VDDH[3V3]_6

DDC_SDA_2

EAG59023302

RXC_D2-

HDMI_HPD_2

OUT_D1+

+5V_NORMAL

OUT_D1-

OUT_DDC_DAT

GND DDC_DATA

OUT_DDC_CLK

5V_HDMI_3

12K

RXA_DDC_DAT

5V_HPD3

RXC_D2+

KRC104S Q8301

R8301

HP_DET

B R8310 4.7K

DDC_SDA_1

CK+_HDMI1

HDMI_HPD_3

KRC104S Q8304

GND

VSS_9

VDDO[3V3]

VSS_4

SHIELD

GND

VDDH[1V8]_2 R8344 R12K

D8301 5.5V OPT

EDID Pull-up

UI_HW_PORT3

D2+

DDC_SDA_3

VSS_1 OUT_C-

47K

C8323 0.1uF 16V HDMI3

Place close to TDA9996

OUT_C+

D2-_HDMI2

R8323

D2D2_GND

R8320 47K

R8315

D1+_HDMI2

R8313 47K

D1+

C8318 0.1uF 16V

C8316 0.1uF 16V

HDMI1

D8310

D1-_HDMI2

5V_HPD4

5V_HPD3 D8307

D0+_HDMI2 D1-

D0+

VSS_12

D0-_HDMI2 D0_GND

OUT_D0+

OUT_D0-

+5V_NORMAL 5V_HDMI_4

CK+_HDMI2 D0-

+5V_NORMAL 5V_HDMI_3

100

CK+

D1+_HDMI4 D1-_HDMI4

CK-_HDMI2 CK_GND

GND

D2-_HDMI4

CK-

D2+_HDMI4

+1.8V_HDMI CEC_REMOTE

HDMI_3 YKF45-7058V

HDMI_RX2+

HDMI_RX2-

HDMI_RX1+

HDMI_RX1-

HDMI_RX0+

R8329

DDC_SCL_2

GND

HDMI_HPD_1

HDMI_RX0-

HDMI_CLK-

HDMI_CLK+

HDMI_SCL

DDC_SDA_2

DDC_SCL_1

R8339

JP8301

RXB_DDC_DAT

R8304 0 HDMI_3

RXB_5V

DDC_SCL_2

0.1uF

OPT

DDC_SDA_1

DDC_CLK

R8324 1.8K

47K HDMI_3

DDC_SDA_2

R8322

R8319 47K HDMI_3

47K

TEST1

8 7

DDC_DATA

R8314

R8312 47K

D8303 5.5V OPT

JP8300

RXB_HPD

HDMI_3 R8303 0

C8312 0.1uF 16V

R8335 0

11 JK830010

0.1uF C8322

EAG59023302

GND

0.1uF C8321

5V_HDMI_4

R8325 1.8K

+5V_NORMAL

HDMI_3 D8309

5V_HPD2

5V_HPD1 D8306

5V_HDMI_2

16 15

HDMI_HPD_2 B R8309 HDMI_3 5V_HPD2 4.7K

R8330

HP_DET 19

HDMI_3 KRC104S Q8303

C8319 0.1uF C8320

HDMI_3 GND R8300

GND E HDMI_3 KRC104S Q8300

D8300 5.5V OPT

SHIELD

+5V_NORMAL 5V_HDMI_2

+5V_NORMAL 5V_HDMI_1

HDMI_SDA

HDMI4

YKF45-7058V GND

UI_HW_PORT2

BCM (EUROBBTV)

LEE GI YOUNG HDMI

2009.06.18

RGB PC

D2B D2A

E0 1

8 VCC

E1 2

7 WC

E2 3

6 SCL

Q2 R8406 22

R8405 22

BCM Reference

RGB_EDID_ST

R8420 10K R8422 100

EDID_WP

R8416 RGB_DDC_SCL R8415

5 SDA

4 0IMMR00014A

D8403 ADUC30S03010L_AMODIODE 30V

2.7K

IC8401 M24C02-RMN6T

D8401 ADUC30S03010L_AMODIODE 30V

RGB_EDID_RENESAS

VSS

GND

SDA

22 RGB_DDC_SDA

22 R8421 0

R8417 0

D1B

SCL

DEV VSS

2.7K

R8402 22

D8409 ENKMC2838-T112 A1

R8414

D1A

RGB_VSYNC

D3A

R8413

RGB_HSYNC

C8401 0.1uF

+5V_NORMAL

VCC

C8406 18pF 50V

R8401 22

D3B

C8404 0.1uF 16V

C8405 18pF 50V

D0B

OPT D8410 CDS3C05HDMI1 5.6V OPT

C8403 22pF 50V

VCC

C8402 22pF 50V

D0A

IC8401-*1 R1EX24002ASAS0A

+5V_NORMAL

IC8400 74F08D

+3.3V_NORMAL

OPT D8408 CDS3C05HDMI1 5.6V

OPT

R8424 10K 1K R8425

L8408 60-ohm DSUB_B

DSUB_DET RGB_BEAD L8409 60-ohm

OPT 0 R8423

DSUB_G

+3.3V_NORMAL

Fiber Optic

GND JP8402

VCC

VINPUT D8400 30V OPT

C8400 0.1uF 16V

JP8400

SPDIF_OUT

SHILED

DDC_CLOCK

V_SYNC

DDC_GND 15

SYNC_GND

BLUE

GND_1

13 9 3

H_SYNC

DDC_DATA

BLUE_GND

GREEN_GND

GREEN

SPG09-DB-010 JK8402

FIX_POLE

RGB AUDIO IN JK8401 PEJ027-01 3

E_SPRING

T_TERMINAL1

B_TERMINAL1

T_SPRING

C8407 PC_R_IN

R_SPRING

RGB IN

JK8400 JST1223-001

JP8401

R8400 1K

RED 1

RGB_0OHM L8409-*1 0 RGB_0OHM L8410-*1 0

RGB_0OHM L8408-*1 0

D8402 D8404 D8405 30V 30V 30V

BCM Reference

R8407 75

R8404 75

GND_2

RGB_BEAD R8403 75

RED_GND

RGB_BEAD L8410 60-ohm

DSUB_R

OPT C8409 D8411 100pF 5.6V 50V ADMC5M03200L_AMODIODE

D8406 AMOTECH 5.6V

R8411 470K

1uF 25V

R8418 0

C8408

B_TERMINAL2

PC_L_IN T_TERMINAL2

D8407 AMOTECH 5.6V

R8412 470K

1uF 25V

R8419 0

EUROBBTV ETC SUB BOARD I/F

2009.06.18

ALL for SIDE_GENDER option

SIDE CVBS PHONE JACK (New Item Developmen)

JK8600 KJA-PH-1-0177 5

M5_GND

M3_DETECT

SIDE_AV_CVBS

R8603 0

D8608 5.1V

C8605 47pF 50V

D8609 5.1V +3.3V_NORMAL R8605 10K SIDE_AV_DET D8601 5.6V

R8608 1K C8600 100pF 50V

C8607 25V

R8606 0 SIDE_AV_L_IN

1uF D8602 5.6V

C8611 100pF 50V

R8601 470K

C8606 25V

R8607 0 SIDE_AV_R_IN

1uF D8603 5.6V

R8602 470K

C8612 100pF 50V

SIDE COMPONENT PHONE JACK (New Item Developmen) L8600 270nH SIDE_COMP_Y D8610 5.1V

C8608 27pF 50V

C8601 27pF 50V

D8611 5.1V

+3.3V_NORMAL

Near J

M5_GND

M3_DETECT

R8600 10K

Run Along SIDE_COMP_Y_IN,SIDE_COMP_Pr_IN,SIDE_COMP_Pb_IN Trace

R8604 1K

0.1uF

SIDE_COMP_INCM

R8609 36

C8613 JK8601 KJA-PH-1-0177

SIDE_COMP_DET C8604 100pF 50V

D8606 5.6V

L8602 270nH SIDE_COMP_Pb D8607 5.5V

C8603 27pF 50V

D8605 5.5V

C8602 27pF 50V

C8610 27pF 50V L8601 270nH SIDE_COMP_Pr

C8609 27pF 50V

WIRELESS READY MODEL

JK8700 KJA-PH-3-0168

Wireless power

VCC[24V/20V/17V]_1 VCC[24V/20V/17V]_2 VCC[24V/20V/17V]_3 VCC[24V/20V/17V]_4 VCC[24V/20V/17V]_5

+24V VCC[24V/20V/17V]_6 DETECT

+3.3V_NORMAL R8704 22K

C8700 0.1uF 50V

INTERRUPT

C8701 2.2uF

TP8700 GND_1

R8714 10K

RESET

G R8705 2.2K

Q8701

R8713

AO3407A

TP8701

GND_2

WIRELESS_DETECT

L8700

I2C_SCL R8702 10K

WIRELESS_PWR_EN

MLB-201209-0120P-N2

WIRELESS_SCL I2C_SDA WIRELESS_SDA

Q8700

GND_3 C8702 0.01uF 50V

C8704 10uF 35V

C8705 10uF WIRELESS_RX 35V

UART_RX UART_TX

WIRELESS_TX GND_4 IR IR_PASS GND_5 GND_6

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 SHIELD

+3.5V_ST

NON_WIRELESS 0 R8703

WIRELESS R8707 0

IC8700 MC14053BDR2G

WIRELESS R8700 WIRELESS_DL_RX 0

Y1 WIRELESS_TX

WIRELESS

VDD

RS232C & Wireless

C8703 15

BCM_TXD1

BCM_RXD1 R8708

INH

R8701

VEE

0.1uF

WIRELESS

WIRELESS_DL_TX

WIRELESS_SW_CTRL

SELECT PIN

STATUS

WIRELESS_RX X0

R8706 0 NON_WIRELESS

+3.5V_ST

HIGH

X1/Y1/Z1

WIRELESS Dongle connect --> WIRELESS RS232

LOW

X0/Y0/Z0

WIRELESS Dongle Dis_con --> S7 RS232

BCM_RX A

OPT

4.7K R8711

Y0 BCM_TX

47K R8712

VSS

OPT

WIRELESS WIRELESS_SW_CTRL

+24V_AMP

+24V

L8803 MLB-201209-0120P-N2

C8827 0.1uF 50V

+1.8V_AMP +3.3V_NORMAL

CCFL = 20V

IC8800

3 Vd=1.4V 1

R8800 1

AP1117E18G-13 ADJ/GND

Edge_LED 32~47 Inch = 20V

120 mA

2 C8800 0.1uF 16V

OUT

55 Inch & IOP Module = 24V

C8803 0.1uF 16V

C8802 10uF 10V

+24V_AMP

SPK_L+ D8800 1N4148W 100V OPT

EMI R8809 3.3

C8819 22000pF 50V

BST1A

VDR1A 25V /RESET

C8816

C8811 0.1uF

CLK_I

AUD_LRCK AUD_SCK SDA1_3.3V SCL1_3.3V

100

R8802

100

R8803

100

R8804

100

R8805

100

VDR2A

BST2A

R8813 12

4.7K

SPEAKER_L

C8839 0.47uF 50V C8842 0.1uF 50V

15uH R8817 12

R8821 4.7K

PVDD1B_2

PVDD1B_1

OUT1B_2

OUT1B_1

PGND1B_2

PGND1B_1

BST1B

VDR1B

PVDD1A_1

PVDD1A_2

OUT1A_1

OUT1A_2

PGND1A_1

51 50

PGND1A_2

OUT2A_2

OUT2A_1

PVDD2A_2

9 10 11

AVDD_PLL

EAN60969601

PVDD2A_1

PVDD2B_2

PVDD2B_1

OUT2B_2

DVDD_PLL

OUT2B_1

GND

PGND2B_2

D8802 1N4148W 100V OPT

50V

R8814 12

R8818 12

L8804 AD-9060 2S

1S C8838 390pF 50V

D8803 1N4148W 100V OPT

R8815 12

1F 15uH

R8816 12

C8840 0.47uF 50V

C8843

R8822

0.1uF 50V

4.7K

C8844

R8823

0.1uF 50V

4.7K

SPEAKER_R

SPK_R-

+24V_AMP

PGND2B_1

27 BST2B

VDR2B

/FAULT

24 MONITOR2

23 MONITOR1

22 MONITOR0

21 SCL

20 SDA

19 BCK

18 WCK

C8818 0.1uF 16V

C8830 22000pF

C8837 390pF 50V

NTP-7000

SPK_R+

C8828 25V1uF

PGND2A_1

OPT C8815 10uF 10V

R8801

PGND2A_2

AGND_PLL

+1.8V_AMP

AUD_LRCH

DGND_PLL

C8807 0.1uF 16V

R8820

C8825 1uF 25V

R8806

VDD_IO

1S C8836 390pF 50V

D8801 1N4148W 100V OPT

39 IC8801

OPT C8805 10uF 10V

C8810 1000pF 50V 3.3K

C8804 0.1uF 16V

100pF 50V

GND_IO

SDATA

C8806

AD DGND_1

DGND_2

OPT C8801 10uF 10V

BLM18PG121SN1D

L8800

L8801

THERMAL 57

1uF +1.8V_AMP

EP_PAD

C8808 1000pF 50V AUD_MASTER_CLK

C8841 0.1uF 50V

SPK_L-

AMP_RESET_N

L8805 AD-9060

C8823 22000pF 50V

L8802

DVDD

BLM18PG121SN1D

+3.3V_NORMAL

+1.8V_AMP

C8824 0.1uF 50V

C8820 0.1uF 50V

C8835 390pF 50V

EMI C8832 0.01uF 50V

C8826 10uF 35V

R8819 12

R8812 12

C8822 1uF 25V

C8831

C8833

0.1uF 50V

C8834 10uF 35V

C8829 22000pF 50V

R8807 0 POWER_DET C8821 1000pF 50V

OPT

+3.5V_ST C8809 33pF 50V

C8812 33pF 50V

C8813 47pF 50V EMI

C8814 47pF 50V EMI

C8817 47pF 50V EMI

R8808

100

WAFER-ANGLE

R8810 10K R8824 0

C B

Q8800 2SC3052

R8811

SPK_L+

AMP_MUTE R8825 0

10K E

SPK_L-

3 R8826 0

SPK_R+

2 R8827 0

SPK_R-

1 P8800

BCM (EUROBBTV)

KIM JONG HYUN NTP7000

2009.06.18

+1.5V_MEMC

D1.5V_DDR3

DDR3 1.5V By CAP - Place these Caps near Memory

0.1uF

C8930

0.1uF

C8929

0.1uF

C8928

0.1uF

C8927

0.1uF

C8926

0.1uF

C8925

0.1uF

C8924

0.1uF C8923

0.1uF C8922

0.1uF

C8921

+3.3V_MEMC

Close to DDR Power Pin

+12V

PGND

L8902

L8905 3.6uH

LX_2

1000pF

C8910

0.1uF

MVREFCA

COMP

R8933 27K POWER_ON/OFF2_2

R8928 10K

C8934 10uF 25V

C8944 0.1uF 16V

OPT C8940 100pF 50V

9.1K 2200pF R8925 C8937

OPT

Vout=0.8*(1+R1/R2)

C8942 22uF 10V

LX_1

R8935 10K

R8919

1K 1% 1%

R8920

0.1uF

1000pF

C8903

AGND C8932 10uF 25V

MVREFDQ

C8909

R8900

1K 1% 1%

R8904

C8901

NR8040T3R6N VIN

OPT

CIC21J501NE

D1.5V_DDR3

R8934 4.7K

D1.5V_DDR3

+3.3V_MEMC

IC8903 AOZ1072AI

0.1uF

C8920

C8919

0.1uF

C8918

0.1uF

C8917

0.1uF

C8916

0.1uF

C8915

0.1uF

C8914

C8913

C8904 0.1uF 16V

10uF

C8902 10uF 10V

C8908

L8900

AR8900 FRC_DQL[5]

DDR3_DQL[5]

FRC_DQL[7]

DDR3_DQL[7] DDR3_DQL[3]

FRC_DQL[3] FRC_DQL[1]

DDR3_DQL[1] 10

IC8900 H5TQ1G63BFR-12C

AR8901 FRC_A[9]

DDR3_A[9]

FRC_A[2]

DDR3_A[2]

FRC_A[0]

DDR3_A[0-12]

DDR3_A[0] A1

A4 ZQ 240 1%

10 AR8903 FRC_DQU[7] FRC_DQU[1]

DDR3_DQU[1]

DDR3_DQU[5]

FRC_DQU[3]

DDR3_DQU[3]

R8909

N9 DDR3_DMU

10 R8910 FRC_DQSL

VDD_1

VDD_2

A10/AP

VDD_3

A11

VDD_4

A12/BC

VDD_5

A13

VDD_6 VDD_7 VDD_9

R8914

DDR3_DML

FRC_DML 10

D2 D1.5V_DDR3

R8911 FRC_DQSU

DDR3_DQSU

F1 H2

10 R8912 FRC_DQSUB

H9 DDR3_DQSUB

VDDQ_2

DDR3_DQU[2]

FRC_DQU[6]

DDR3_DQU[6]

FRC_DQU[0]

DDR3_DQU[0]

FRC_DQU[4]

DDR3_DQU[4]

J9 L1 L9 T7

CK CK

VDDQ_4

CKE

VDDQ_5 CS

VDDQ_7

ODT

VDDQ_8

RAS

VDDQ_9

CAS

NC_1 NC_2

B3 DDR3_A[3]

DDR3_A[5]

FRC_A[7]

DDR3_A[7]

DDR3_RESETB

M1 M9 P1

AR8905

P9 DDR3_CASB

DDR3_ODT

FRC_WEB

DDR3_WEB

FRC_BA0

DDR3_BA0 10

D1 D8 E2 E8

R8916

F9 DDR3_MCLK

FRC_MCLK

DDR3_A[11]

DDR3_A[12]

10 R8917

G1 G9

DDR3_MCLKB

N8 M3

ADJ/GND DDR3_BA1 DDR3_MCLK

K1 J3 K3 L3

C8938 16V 10uF R8929 56

C8935 10uF 16V

DDR3_BA2

DDR3_MCLKB

C8946 0.1uF 16V

DDR3_CKE DDR3_ODT DDR3_RASB DDR3_CASB DDR3_WEB

D1.5V_DDR3 R8923 10K

DDR3_RESETB F3 DQSL

G3 C7

VSS_1

DQSU

VSS_2

DQSU

VSS_3

B7 E7

VSS_4

DML

VSS_5

DMU

VSS_6 VSS_7

DQL0

VSS_8

DQL1

VSS_9

DQL2

VSS_10

DQL3

VSS_11

DQL4

VSS_12

DQL5

DDR3_DQSL DDR3_DQSLB DDR3_DQSU DDR3_DQSUB DDR3_DML DDR3_DMU

DDR3_DQL[0]

DDR3_DQL[1]

DDR3_DQL[2]

DDR3_DQL[3]

DDR3_DQL[4]

DDR3_DQL[5]

DDR3_DQL[6]

DDR3_DQL[7]

DDR3_DQU[0]

DDR3_DQU[1]

DDR3_DQU[2]

DDR3_DQU[3]

DDR3_DQU[4]

DDR3_DQU[5]

DDR3_DQU[6]

DDR3_DQU[7]

DDR3_DQL[0-7]

URSA3 CORE 1.26V

DQL7 +12V

VSSQ_1 VSSQ_2

DQU0

VSSQ_3

DQU1

VSSQ_4

DQU2

VSSQ_5

DQU3

VSSQ_6

DQU4

VSSQ_7

DQU5

VSSQ_8

DQU6

VSSQ_9

DQU7

+1.26V_MEMC

IC8902 AOZ1072AI PGND

L8904 3.6uH

LX_2

NR8040T3R6N VIN

AGND

DDR3_DQU[0-7]

R8918

OUT

DDR3_BA0

10 C8931 10uF 25V

C8933 10uF 25V

LX_1

POWER_ON/OFF2_1 R8926 10K

DDR3_CKE

FRC_CKE

1074 mA

RESET

DQL6

B9 DDR3_RASB

FRC_MCLKB

IC8901 AP1117EG-13

NC_4

R8915 FRC_RASB

DDR3_A[10]

NC_3 NC_6

FRC_A[5]

FRC_ODT

DDR3_A[9]

+1.5V_MEMC

+3.3V_MEMC

DDR3_A[8]

DQSL

AR8906

FRC_CASB

FRC_DDR3_RESETB

DDR3_A[7]

VDDQ_6

FRC_A[3]

DDR3_A[6]

VDDQ_3

AR8904

DDR3_A[5]

M2 BA0

VDDQ_1

FRC_DQU[2]

DDR3_A[4]

BA2

A1 DDR3_DQSLB

URSA3 DDR3 1.5V

BA1

R8913

DDR3_A[3]

A15

VDD_8

DDR3_DQSL 10

FRC_DQSLB

A6 A7

B2 DDR3_DQU[7]

FRC_DQU[5]

FRC_DMU

DDR3_A[2]

R8936 1

R8921

DDR3_A[1]

COMP

C8941 22uF 10V

C8943 0.1uF 16V

OPT C8939 100pF 50V

6.2K 3300pF R8924 C8936

DDR3_DQL[4]

R8930 3.3K

DDR3_DQL[6]

DDR3_DQL[2]

FRC_DQL[6]

VREFDQ

DDR3_A[0]

R8931 3.9K

FRC_DQL[2] FRC_DQL[4]

10 AR8902 FRC_DQL[0]

270 R8927

MVREFDQ

VREFCA

L8903 CIC21J501NE

DDR3_DQL[0]

L8901

MVREFCA

150

DDR3_BA2

OPT R8922

FRC_BA2

DDR3_A[8]

FRC_A[6]

DDR3_A[6]

FRC_A[4]

DDR3_A[4]

FRC_BA1

Vout=0.8*(1+R1/R2)

R8932 12K

AR8908 FRC_A[8]

DDR3_BA1 10 AR8907 DDR3_A[10]

FRC_A[10]

DDR3_A[12]

FRC_A[12] FRC_A[1]

DDR3_A[1] DDR3_A[11]

FRC_A[11] 10

COMMON URSA3 DDR & Power

2009.09.11 89

IC9301 LG5111

+1.8V_PLL

+1.8V_RXVDD

IC9301 LG5111 +1.8V_RXVDD

RXA0+

RXA0-

Close to LG5111 LVDS Input PIN

RXA1+

RXA1-

RXA2+ RXA0+

R9304

100

RXA1+

R9305

100

RXA2+

R9306

100

RXACK+

R9307

100

RXA3+

R9308

100

RXA4+

R9309

100

RXA0-

RXA2-

RXA1-

RXACK+

RXA2-

RXACK-

B2 C2 C1 C3

RXA3+

RXACKRXA3-

RXA3-

RXA4-

RXA4+

D3 D1 D2

RXA4-

RXB0+

100

RXB1+

R9311

100

RXB2+

R9312

100

RXBCK+

R9313

100

RXB3+

R9314

100

RXB4+

R9315

100

RXB0-

RXB1-

RXB1+

RXB2-

RXB1-

RXBCK-

RXB2+

RXB3-

RXB2-

RXB4-

RXBCK+

E1 E3 F3 F1 F2 G1 G2

RXBCK-

RXB3+

RXB3-

RXB4+ RXC0+

R9316

100

RXC1+

R9317

100

RXC2+

R9318

100

RXCCK+

R9319

100

RXC3+

R9320

100

RXC4+

R9321

100

RXB4-

RXC0-

RXCCK-

RXC0+

RXC3-

RXC0-

K2 L1

RXC1+

RXC4-

L2 M1 M2 N2

RXCCK+ RXD1+

R9323

100

RXD2+

R9324

100

RXDCK+

R9325

100

RXD3+

R9326

100

RXD4+

R9327

100

T1B1P

R1B1M

T1B1N

R1C1P

T1C1P/RLV0N

R1C1M

T1C1N/RLV0P

R1CLK1P

T1CLK1P/RLV1N

R1CLK1M

T1CLK1N/RLV1P

R1D1P

T1D1P

R1D1M

T1D1N

R1E1P

T1E1P/RLV2N

R1E1M

T1E1N/RLV2P

R1A2P

T1A2P/RCLKN

R1A2M

T1A2N/RCLKP

R1B2P

T1B2P

R1B2M

T1B2N

R1C2P

T1C2P

RRXA0-

B16

R1C2M

T1C2N

R1CLK2P

T1CLK2P/RLV3N

R1CLK2M

T1CLK2N/RLV3P

R1D2P

T1D2P/RLV4N

R1D2M

T1D2N/RLV4P

R1E2P

T1E2P/RLV5N

R1E2M

T1E2N/RLV5P

C9307 27pF 50V

RXD0-

RXCCK-

RXD1-

RXC3+

RXD2-

RXC3-

RXDCK-

RXC4+

RXD3-

RXC4-

N1 N3 P3 P1 P2

T2A1P

R2A1M

T2A1N

R2B1P

T2B1P/LLV0N

R2B1M

T2B1N/LLV0P

R2C1P

T2C1P/LLV1N

R2C1M

T2C1N/LLV1P

R2CLK1P

T2CLK1P/LLV2N

R2CLK1M

T2CLK1N/LLV2P

R2D1P

T2D1P

R2D1M

T2D1N

R2E1P

T2E1P/LCLKN

R2E1M

T2E1N/LCLKP

RRXA2+/RLV5P

B18

RRXA2-/RLV5N

C18

RXD0+

R1 R3 T3

RXD1-

RXD2+

RXD2-

RXDCK+

RXDCK-

RXD3+

RXD3-

RXD4+

RXD4-

R2A2P

T2A2P

R2A2M

T2A2N

R2B2P

T2B2P

R2B2M

T2B2N

R2C2P

T2C2P/LLV3N

R2C2M

T2C2N/LLV3P

R2CLK2P

T2CLK2P/LLV4N

R2CLK2M

T2CLK2N/LLV4P

R2D2P

T2D2P

R2D2M

T2D2N

R2E2P

T2E2P/LLV5N

R2E2M

T2E2N/LLV5P

L3 M3

C17

RRXACK-/RLV4N

D16

RRXA3+

C16

RRXA3-

D17

P4 CLK25_XOUT

TMODE3

CLK25_XIN

TMODE2 TMODE1

RRXA4+/RLV3P

D18

RRXA4-/RLV3N

RRXB0+/RLCLKP

E17

RRXB0-/RLCLKN

F16

RRXB1+

E16

RRXB1-

F17

RRXB2+

F18

M0_SCLK

R9342

M0_MOSI

R9343

M1_SCLK

R9344

M1_MOSI

R9345

M2_SCLK

R9346

M2_MOSI

R9347

M3_SCLK

R9348

M3_MOSI

R9349

RRXB2-

G18

RRXB3+/RLV1P

H17

S_SCLK

RRXB3-/RLV1N

J18

S_MOSI

J17

GPIO0

M1_MOSI

GPIO1

M2_SCLK

GPIO2

M2_MOSI

GPIO3

M3_SCLK

GPIO4

M3_MOSI

GPIO5

K17 L18

R9350

LLV5N

M18

LLV4P

M17

V_SYNC L_VS

LLV4N

N18

LLV3P

N17

S_SCLK EEPROM_WP

P17

P18

LLCLKN

A10 A11 A12 A13 B4

LG5111_RESET OPT_N

LLCLKP

K16 L16

M15

R10

M16

R11

N15

R12

P15

R13

T8 R9359 U8

C4 22

EEPROM_WP

+1.8V_VDD

EEPROM_NA

EEPROM_A1

C14 D6

TCON_EN R_VS

M_SDA

DUAL_LVDS

M_SCL

B10 B11

POL_A

B12

VS_IN

S_SDA

L_VS

S_SCL

U7 R9360 V7 R9361

D13 22

M_SDA

M_SCL

G12

U9 R9362 V9 R9363

H12 22

SDA3_3.3V

SCL3_3.3V

J12 K7

H_CONV DPM

K12

V10

SOE

UARTRXD

PORES_N

UARTTXD

U10R9364

UART_RXD UART_TXD

L7 L12 M7

OPT_N POL

T11

FLK

TMS TCK

R17

TDI

T16

TDO

R16

TMS

U11 V12 U12R9365 V11

TRST_N

TCK

M10

TDI TDO

M11

TRST_N

M12

GCLK1[GSP_R]

LLV1N

V15

B13 GVDD_EVEN/GOE GVST/GSP

B14 B15

LLV0P

V17

GCLK2

A14

GVDD_ODD/GSC

U16 V16

V13

LLV1P

U17

LLV0N

VDD_ODD[GSC]

GCLK3

VDD_EVEN[GOE] GCLK4[OPT_P] VST[GSP]

GCLK5

RMLVDS

GCLK6

U13

GCLK1/GSP_R

GCLK2

T13 T14 V14 U14

GCLK3

C10

GCLK4/OPT_P

C11

GCLK5 GCLK6

C12 C13 D7

Mini-LVDS Signal Strength!!

R9339 11K

D8 D9 D10 D11 D12 G8 G9 G10 G11

+3.3V_NORMAL

RX_GND_5

RXVDD_18_6

RX_GND_6

C9324 0.1uF 16V

C9331 0.1uF 16V

C9338 0.1uF 16V

C9345 0.1uF 16V

C9319 0.1uF 16V

C9325 0.1uF 16V

C9332 0.1uF 16V

C9339 0.1uF 16V

C9346 0.1uF 16V

C9351 0.1uF 16V

C9357 0.1uF 16V

C9364 0.1uF 16V

C9369 0.1uF 16V

C9320 0.1uF 16V

C9326 0.1uF 16V

C9333 0.1uF 16V

C9340 0.1uF 16V

C9347 0.1uF 16V

C9352 0.1uF 16V

C9358 0.1uF 16V

C9365 0.1uF 16V

C9370 0.1uF 16V

C9321 0.1uF 16V

C9327 0.1uF 16V

C9334 0.1uF 16V

C9341 0.1uF 16V

C9348 0.1uF 16V

C9353 0.1uF 16V

C9359 0.1uF 16V

C9366 0.1uF 16V

C9371 0.1uF 16V

C9322 0.1uF 16V

C9328 0.1uF 16V

C9335 0.1uF 16V

C9342 0.1uF 16V

C9349 0.1uF 16V

C9354 0.1uF 16V

C9360 0.1uF 16V

C9367 0.1uF 16V

C9372 0.1uF 16V

C9323 0.1uF 16V

C9329 0.1uF 16V

C9336 0.1uF 16V

C9343 0.1uF 16V

C9350 0.1uF 16V

C9355 0.1uF 16V

C9361 0.1uF 16V

C9362 0.1uF 16V

C9368 0.1uF 16V

J4 K4 L4 M4 +1.8V_TXVDD

F14 TXVDD_18_1

TX_GND_1

TXVDD_18_2

TX_GND_2

TXVDD_18_3

TX_GND_3

TXVDD_18_4

TX_GND_4

TXVDD_18_5

TX_GND_5

TXVDD_18_6

TX_GND_6

TXVDD_18_7

TX_GND_7

TXVDD_18_8

TX_GND_8

TXVDD_18_9

TX_GND_9

TXVDD_18_10

TX_GND_10

TXVDD_18_11

TX_GND_11

TXVDD_18_12

TX_GND_12

G14

C9313 0.1uF 16V

H14

C9373 0.1uF 16V

C9375 0.1uF 16V

H15 J14 J15 K14 K15 L14

+1.8V_VDD

L15 M14 N14

C9314 0.1uF 16V

C15 PLL_AVDD

GND_1

PLL2_AVDD

GND_2 GND_3

VDD_18_1

GND_4

VDD_18_2

GND_5

VDD_18_3

GND_6

VDD_18_4

GND_7

VDD_18_5

GND_8

VDD_18_6

GND_9

VDD_18_7

GND_10

VDD_18_8

GND_11

VDD_18_9

GND_12

VDD_18_10

GND_13

VDD_18_11

GND_14

VDD_18_12

GND_15

VDD_18_13

GND_16

VDD_18_14

GND_17

VDD_18_15

GND_18

VDD_18_16

GND_19

VDD_18_17

GND_20

VDD_18_18

GND_21

VDD_18_19

GND_22

VDD_18_20

GND_23 GND_24

LLV2N

U18

RXVDD_18_5

+3.3V_VDD

LLV2P

T18

RX_GND_4

VS_SLAVE_MODE

R18

T17

RX_GND_3

RXVDD_18_4

C9318 0.1uF 16V

+1.8V_PLL

R14

EEPROM_A1

R9351

SOE_A

N16

J16

R9337 3.3K TM240Hz

H_CONV DPM_A

LLV3N

P16

G16

S_CS

DUAL_LVDS +3.3V_NORMAL

LLV5P

L17

RXVDD_18_3

EEPROM_NA

/TCON_EN R_VS

RX_GND_2

GPIO7

RRXB4-/RLV0N T5

G15

M1_SCLK

S_MOSI

RRXB4+/RLV0P

F15

H16

M0_MOSI

S_CS_N

M0_SCLK

GPIO6

RRXBCK-/RLV2N

H18

RX_GND_1

RXVDD_18_2

E15

TMODE0

RRXBCK+/RLV2P

G17

C9312 0.1uF 16V

G4 RXVDD_18_1

+1.8V_TXVDD

RRXACK+/RLV4P

FLK_A

RXD1+

IC9301 LG5111

R9341

RXD4-

RXD0-

RRXA1-

B17

K18 R2A1P

X9300 25MHz

RRXA1+

A15

E18

RXC2+

100

R1B1P

C9304 27pF 50V

RRXA0+

A16

VS_SLAVE_MODE

RXC2R9322

T1A1N

RXC1RXC2-

RXC1-

RXD0+

T1A1P

R1A1M

RXB0+ R9310

A17 R1A1P

VDD_33_1

GND_25

VDD_33_2

GND_26

VDD_33_3

GND_27

VDD_33_4

GND_28

VDD_33_5

GND_29

VDD_33_6

GND_30

VDD_33_7

GND_31

VDD_33_8

GND_32

VDD_33_9

GND_33

VDD_33_10

GND_34

VDD_33_11

GND_35

VDD_33_12

GND_36

VDD_33_13

GND_37

VDD_33_14

GND_38

VDD_33_15

GND_39

VDD_33_16

GND_40

VDD_33_17

GND_41

VDD_33_18

GND_42

D4 D5 D14 D15

+1.8V_VDD

E5 E14 F4

C9315 0.1uF 16V

F5 G5 H5 H8 H9 H10 H11

+3.3V_VDD

J5 J8 J9

C9316 0.1uF 16V

J10 J11 K5 K8 K9 K10 K11

+3.3V_VDD

L5 L8 L9

C9317 0.1uF 16V

L10 L11 M5 N4 N5

+1.8V_L/DIMMING

+1.8V_RXVDD +1.8V_TXVDD +1.8V_PLL

+1.8V_VDD

+3.3V_NORMAL

+3.3V_VDD

P5 P14 R15 T7

L9302

120-ohm

L9303

120-ohm

L9304

120-ohm

L9305

120-ohm

L9306

120-ohm

T9 T10

C9374 10uF 10V

T12 T15 U15

+3.3V_NORMAL

[+1.8V for LG5111] R9300 3.3K TM480Hz

+12V

R9329 3.3K TM480Hz

C9330 10uF 10V

IC9302 AOZ1072AI Vout = 0.8*(1+R1/R2)

/TCON_EN

C9337 10uF 10V

C9344 10uF 10V

C9356 10uF 10V

+1.8V_L/DIMMING

DUAL_LVDS L9300

R9301 10K TM240Hz

120-ohm

R9330 10K TM240Hz

PGND

Dual/Quad-Link LVDS Input Selection - High : Dual-Link LVDS(TM480Hz,LE9500) - LOW : Quad-Link LVDS (TM240Hz, LE5500/7500/8500)

C9302 10uF 25V

AGND

C9303 10uF 25V

+3.3V_NORMAL

LX_2

R1 VIN

TX Output Mode Selection - High : LVDS(TM480Hz, LE9500) - LOW : Mini-LVDS (TM240Hz, LE5500/7500/8500)

L9301 3.6uH

LX_1

C9309 22uF 10V

C9310 0.1uF 16V

R9355 2K 1%

COMP R9338 9.1K

+3.3V_NORMAL

C9308 2200pF

[JTAG for LG5111] P9101

R9331 3.3K OPT

R9302 3.3K TM480Hz

R9354 10.5K 1%

+3.3V_NORMAL R9340 10K

EEPROM_NA

VS_SLAVE_MODE

12505WS-09A00

C9305 1000pF 50V

+3.3V_NORMAL

R9356 10K 1% R2 1

R9303 10K TM240Hz

R9332 10K 2

Master/Slave Mode Selection - High : Slave Mode(TM480Hz,LE9500) - LOW : Master Mode (TM240Hz,LE5500/7500/8500)

External Serial EEPROM Avalibility - High : Not Available - LOW : Use EEPROM

C9163 0.1uF 16V

R9183

[UART for LG5111] 22

P9301

TDO

1 5

R9184

[EEPROM for LG5111]

R9328

R9377 330

KIA7027AF I

OPT 2

10K OPT

R9376

UART_RXD

TX UART_TXD

5 9

VCC

R9187 22 OPT

LG5111_RESET

IC9303 M24512-WMW6G(REV.B)

R9333

OPT

TRST_N

C9363 0.1uF 16V

8 C9306 0.1uF 16V

+3.3V_NORMAL

IC9300

TMS

GND

R9352 3.3K OPT

R9357 2K

R9358 2K

R9188

R9189

R9190

R9191

10K

R9192 1K

1K OPT

R9186

+3.3V_NORMAL

OPT SW9300 JTP-1127WEM

R9185

Write Protection Low : Normal Operation High : Write Protection

[RESET for LG5111]

R9335 3.3K

I2C Slave Address : 0xA4 +3.3V_NORMAL

+3.3V

TCK 2

+3.3V_NORMAL

12505WS-04A00 TDI

R9334

2 C9300 0.1uF 16V OPT

E1 LG5111_RESET

EEPROM_A1

WC EEPROM_WP

OPT G

C9301 4.7uF 10V OPT

R9336 10K OPT

VSS

SCL M_SCL SDA M_SDA R9353 10K

LOCAL_DIMMING_EEPROM

COMMON LG5111 (L.D.) from URSA3

09/10/13

C9039

22pF X9000

22pF

HIGH FRC OPTION LOW NON_MIRROR MIRROR K14 LVDS

NON_GIP

NON_LD

C9009 0.1uF C9019 10uF

C9032 0.1uF

FRC_A[4]

FRC_A[5]

FRC_A[6]

FRC_A[7]

FRC_A[8]

FRC_A[9]

FRC_A[10]

FRC_A[11]

FRC_A[12]

FRC_BA1

FRC_BA2 C9005 0.1uF

C9020 10uF

C9025 10uF

C9030 0.1uF

C9033 0.1uF

C9034 0.1uF

C9035 0.1uF

U2 T4

FRC_CKE

J1 H3

FRC_CASB

FRC_WEB

L9001 CIC21J501NE C9016 0.1uF

C9021 0.1uF

AVDD_DDR L9002 CIC21J501NE C9022 0.1uF

URSA3_SCANNING_OFF URSA3_SCANNING_ON R9055 R9054 4.7K 4.7K

URSA3_NON_GIP R9052 4.7K URSA3_GIP R9053 4.7K

URSA3_LOCAL_DIMMING R9057 4.7K

C13 REXT

N13

M14

RESET

SPI_DO

N14

P13

U13

T12

N12

SPI_DI

SPI_CZ

SPI_CK

SOFT_RST_R

SOFT_RST_L

PLL_LOCK_R

PLL_LOCK_L

R12 OP_SYNC_R

OP_SYNC_L

U10

U12

U11

R10

R11 LTD_DE_R

LTD_DE_L

LTD_DA1_R

LTD_DA1_L

E13

E4 GPIO[9]

GPIO[10]

GPIO[8]

GPIO[5]

GPIO[4]

G13

H14

J13

K14

F14 GPIO[3]

GPIO[2]

GPIO[1]

B9 XTALI

GPIO[0]

XTALO

A5 RO4N

RO4P

B5 RO3N

RO3P

RO2N

A7 RO2P

RO1N

C8 RO1P

RO0N

RO0P

ROCKN

ROCKP

A1 RE4N

RE4P

RE3N

C2 RE3P

RE2N

A3 RE2P

RE1N

RE1P

C3 RE0N

DDR3_A9/DDR2_A9

A3M/RV4-

DDR3_A10/DDR2_A11

A4P/RV5+

DDR3_A11/DDR2_A4

A4M/RV5-

C9027 0.1uF

C9031 0.1uF

FRC_DQL[0]

FRC_DQL[1]

FRC_DQL[2]

FRC_DQL[3]

FRC_DQL[4]

FRC_DQL[5]

FRC_DQL[6]

FRC_DQL[7]

FRC_DQU[0]

FRC_DQU[1]

VDDC

L9003 CIC21J501NE

B0M/RV6-

DDR3_BA1/DDR2_ODT

B1P/RV7+

DDR3_BA2/DDR2_A12

B1M/RV7B2P/RV8+

DDR3_MCLK/DDR2_MCLK

B2M/RV8-

DDR3_MCLKZ/DDR2_MCLKZ

BCKP/WPWM BCKM/OPT_P B3P/OPT_N

DDR3_ODT/DDR2_BA1

B3M/FLK

DDR3_RASZ/DDR2_WEZ

B4P/GCLK6

DDR3_CASZ/DDR2_CKE

FRC_DQU[3]

FRC_DQU[4]

FRC_DQU[5]

FRC_DQU[6]

FRC_DQU[7]

C0M/LV0-

LGE7378A[FRC_TCON_URSA3]

DDR2_DQS0/DDR3_DQS0

C1P/LV1+ C1M/LV1C2P/LV2+ C2M/LV2-

DDR2_DQSB0/DDR3_DQSB0

CCKP/LV3+

DDR2_DQSB1/DDR3_DQSB1

CCKM/LV3C3P/LV4+

DDR2_DQ7/DDR3_DQM0

C3M/LV4-

DDR2_DQ11/DDR3_DQM1

C4P/LV5+

DDR2_DQ6/DDR3_DQ0 DDR2_DQ0/DDR3_DQ1

D0P/LV6+

DDR2_DQ1/DDR3_DQ2

D0M/LV6-

DDR2_DQ2/DDR3_DQ3

D1P/LV7+

DDR2_DQ4/DDR3_DQ4

D1M/LV7-

DDR2_NC/DDR3_DQ5

D2P/LV8+

DDR2_DQ3/DDR3_DQ6

D2M/LV8DCKP/GOE DCKM/GSC/GCLK3

DDR2_DQ8/DDR3_DQ8

D3P/GSP_R

DDR2_DQ14/DDR3_DQ9

D3M/GSP

DDR2_DQ13/DDR3_DQ10

D4P/SOE

DDR2_DQ12/DDR3_DQ11

D4M/POL

DDR2_DQ15/DDR3_DQ12 GCLK4

DDR2_DQ10/DDR3_DQ14

GCLK2

RXA3+

B17

RXA3-

C16

RXA4+

C17

RXA4RXB0+

D17

RXB0-

D15

RXB1+

E15

RXB1-

F16

RXB2+

F17

RXBCK+

G15

RXBCK-

G17

RXB3+

G16

RXB3-

H16

RXB4+

H17

RXB4RXC0+

J15

RXC0-

J17

RXC1+

J16

RXC1-

K16

RXC2+

K17

RXC2-

K15

RXCCK+

L15

RXCCK-

L17

RXC3+

L16

RXC3-

M16

RXC4+

M17

RXC4RXD0+

N15

RXD0-

N17

RXD1+

N16

RXD1-

P15

RXD2+

R15

RXD2-

R17

RXDCK+

R16

RXDCK-

T16

RXD3+

T17

RXD3-

T15

RXD4+

U17

RXD4-

P17

URSA3_SDA

I2CS_SCL

URSA3_SCL P14 R14 B13

DVDD_DDR[1.26V]

LPLL_FBCLK LPLL_OUTCLK

FRC_PWM1

U16

R9043

V_SYNC

OPT

A13

VB1_TEST

+3.3V_MEMC

F10

TESTPIN

D11 L13

D11

C11

B12 C11

B12

B11

B10 B11

A12 B10

A11 A12

A11

A10

VSS_27 A10

VSS_26 P6

VSS_24

VSS_25 N4

VSS_23 L11

VSS_22

VSS_21 L9

L10

VSS_20 K11

K10

VSS_19

VSS_17

VSS_16

VSS_18 K9

VSS_15 J11

VSS_14

VSS_13 J9

VSS_12 J8

J10

VSS_11

VSS_9

VSS_10 J4

H11

H10

VSS_8

VSS_7 H9

VSS_5

VSS_4

VSS_6 H8

G10

VSS_2

VSS_3 G9

C12

VSS_1

VDDP_5 C10

M11

VDDP_4

VDDP_3 M10

VDDP_1

VDDP_2 K6

VDDC_8 G11

VDDC_7

VDDC_6 H6

VDDC_5

VDDC_3

VDDC_4 G7

VDDC_2 G5

VDDC_1

VDD_ODD F6

E17

VDD_EVEN

LPLL_REFIN

E16

AVDD_PLL_2

F12

F11

AVDD_PLL_1

AVDD_MEMPLL

AVDD_LVDS_4 M6

K12

AVDD_LVDS_3

AVDD_LVDS_2 J12

H12

AVDD_LVDS_1

P9000 12505WS-04A00

G12

I2CM_SCL2_R

AVDD_DDR_6

I2CM_SDA2_R

N10

AVDD_DDR_5

R9016

100

I2CM_SCL2_L AVDD_DDR_4

I2CM_SDA2_L AVDD_DDR_3

100 100

FRC_PWM0

PWM1

I2CM_SCL

R9014 R9015

I2CM_SDA

AVDD_DDR_2

100

AVDD_DDR_1

100

R9013

100

R9012

PWM0

R9011

RXB2-

F15

D1 I2CS_SDA

C9023 0.1uF

AVDD_2

C9018 0.1uF

AVDD_1

1 22

R9003

URSA3_SDA R9040

2 22

R9004

AVDD

URSA3_SCL 22

R9007

AVDD_DDR

AVDD_LVDS

AVDD_PLL

VDDC

VDDP

SCL3_3.3V

FRC_CONF1

AVDD_MEMPLL 22

R9008

FRC_CONF0

R9048

C9015 0.1uF

RXACK-

A17

P16

DDR2_DQ9/DDR3_DQ13

C9012 0.1uF

RXACK+

A16

M15

DDR2_DQM0/DDR3_NC C9008 10uF

RXA2-

B16

C4M/LV5-

M2 C9003 10uF

RXA2+

B15

H15 C0P/LV0+

DDR2_DQM1/DDR3_DQ15

FRC_DQU[0-7]

RXA1-

A15

B4M/GLCK5

IC9001

DDR2_DQ5/DDR3_DQ7

FRC_DQU[2]

RXA1+

C15

D16 B0P/RV6+

DDR3_BA0/DDR2_BA2

FRC_DQL[0-7]

+1.26V_MEMC

A3P/RV4+

DDR2_DQS1/DDR3_DQS1

FRC_DMU

C9017 0.1uF

ACKM/RV3-

DDR3_A8/DDR2_A2

FRC_DML

C9014 0.1uF

ACKP/R3+

DDR3_A7/DDR2_A5

DDR3_RESET/DDR2_A3

FRC_DQSUB

C9011 0.1uF

DDR3_A6/DDR2_A0

FRC_DQSL

C9007 10uF

A2M/RV2-

FRC_DDR3_RESETB

C9026 0.1uF

FRC_DQSU

C9002 10uF

A2P/RV2+

DDR3_A5/DDR2_A10

DDR3_WEZ/DDR2_BA0

FRC_DQSLB

+1.5V_MEMC

DDR3_A4/DDR2_CASZ

RXA0-

C14

R9050

C9013 0.1uF

A1M/RLV1-

RXA0+

A14

R9049 OPT 1K

C9010 0.1uF

DDR3_A3/DDR2_A1

FRC_RASB

C9006 10uF

A1P/RV1+

DDR3_CKE/DDR2_RASZ

FRC_ODT VDDP

C9001 10uF

A0M/RV0-

FRC_MCLK FRC_MCLKB

+3.3V_MEMC

B14 A0P/RV0+

FRC_BA0 L9006 CIC21J501NE C9000 10uF

DDR3_A2/DDR2_A7

DDR3_A12/DDR2_A8

AVDD_LVDS

+3.3V_MEMC

L9000 CIC21J501NE

DDR3_A1/DDR2_A6

CHANNEL CHECK!

R9051 OPT 1K

AVDD_MEMPLL

C9029 0.1uF

FRC_A[3]

DDR3_A0/DDR2_NC

820

R9044 OPT R9046

+3.3V_MEMC

C9024 10uF

R9047 OPT1K

C9004 10uF

FRC_A[2]

L9005 CIC21J501NE

FRC_A[1]

L9004 CIC21J501NE

FRC_A[0]

SW9000 JTP-1127WEM

AVDD

+3.3V_MEMC

RE0P

A2 AVDD_PLL

+3.3V_MEMC

RECKN

RECKP

FRC_A[0-12]

+3.3V_MEMC

R9041

LTD_DA0_L

DIO

LTD_CLK_R

5 EAN35097301

T11

URSA3_FLASH_WINBOND_OLD

T10

GND

URSA3_MINI_LVDS R9035 4.7K

URSA3_MIRROR R9033 4.7K

100

CLK

LTD_CLK_L

100

HOLD

FRC_CONF1

T14

URSA3_FLASH_MACRONIX

S_M_PIF_FC

R9028

T13

EAN61009401 DO

100

100 R9022

VCC

R13

U15

S_M_PIF_DA1

U14

FRC_SPI_CK FRC_SPI_DI

S_M_PIF_CS

S_M_PIF_DA0

R9006

S_M_PIF_CLK

URSA3_LVDS R9036 4.7K

GND 4

R9027

R9021 IC9000-*2 W25X40VSSIG

M_S_PIF_FC

R9005

SCLK

M_S_PIF_CS

HOLD#

M_S_PIF_DA1

WP# 3

M_S_PIF_CLK_2

100

URSA3_NON_MIRROR R9034 4.7K

SO 2

R9026

R9020

10K

VCC

100

R9002

100

R9001

FRC_SPI_DO

CS# 1

R9032

100

R9031

DI[IO0]

R9025

M_S_PIF_CLK_1

R9019

URSA3_FLASH_WINBOND_NEW

R9000

FRC_SPI_CZ

100

CLK

R9024

R9018

HOLD

100

+3.3V_MEMC

R9023

100

GPIO[14]

GND

R9017 VCC

GPIO[13]

GPIO[12]

IC9000 MX25L4005CM2I-12G

0.1uF

C9028

DO[IO1]

FRC_CONF0

IC9000-*1 W25X40BVSSIG CS

100 R9042

+3.3V_MEMC

FRC_RESET

SCAN_ON

FRC_SPI_DO

SCAN_OFF

FRC_SPI_CK

MINI_LVDS

GIP

FRC_SPI_CZ FRC_SPI_DI

R9029

URSA3_NON_LOCAL_DIMMING R9056 4.7K

T10 R10 R9 U10

12MHz

LTD_DA0_R

LVDS_TX_0_DATA4_N

LVDS_TX_0_DATA4_P

LVDS_TX_0_DATA3_N

LVDS_TX_0_DATA3_P

LVDS_TX_0_DATA2_N

LVDS_TX_0_DATA2_P

LVDS_TX_0_DATA1_N

LVDS_TX_0_DATA1_P

LVDS_TX_0_DATA0_N

LVDS_TX_0_DATA0_P

LVDS_TX_0_CLK_N

LVDS_TX_0_CLK_P

LVDS_TX_1_DATA4_P

LVDS_TX_1_DATA4_N

LVDS_TX_1_DATA3_N

LVDS_TX_1_DATA3_P

LVDS_TX_1_DATA2_N

LVDS_TX_1_DATA2_P

LVDS_TX_1_DATA1_N

LVDS_TX_1_DATA1_P

LVDS_TX_1_DATA0_N

LVDS_TX_1_DATA0_P

LVDS_TX_1_CLK_N

LVDS_TX_1_CLK_P

Serial Flash

C9038

SDA3_3.3V

FRC_PWM1

FRC_PWM0 OPT

URSA3_SDA

22 R9009 OPT 22

R9010

SCL1_3.3V

SDA1_3.3V

SCAN_BLK2

VDDC L9007 CIC21J501NE

LD_SCAN R9038 100

FRC_PWM1

LD_SCAN R9039 100

FRC_PWM0

R9045

URSA3_SCL

SCAN_BLK1/OPC_OUT C9037 0.1uF

COMMON URSA3 (L.D.)

Separate DVDD_DDR Power

I2C ADR: GPIO1: HI:B8 LOW:B4 CHIP_CONF: {GPIO8, PWM1, PWM0} CHIP_CONF= 3 d5: boot from internal SRAM CHIP_CONF= 3 d6: boot from EEPROM CHIP_CONF= 3 d7: boot from SPI Flash

C9036 10uF

2009.09.11 94

[LEVEL Shift Block]

D9103 MMSD4148T1G

[POWER Block]

VCC_LCM (+3.3V)

R9108 100 GIP

CHECK Value!!

TCON_42_FHD

R9165 18K 1% OPT

R9156 150K 1%

TCON_42_FHD

C9134 OPT

0.1uF 50V

33K NON_GIP

To reduce Audible noise

C9126 0.047uF VGH_FB

AGND

CRST

PGOOD

COMP

FB1

SW0

SW1

LX1

PGND

DEL2

NON_GIP

FBP GPGND

R9148-*1

R9133-*1 R9134-*1 200 200 NON_GIP NON_GIP

GCLK2_I

0 GIP R9155-*1

GCLK1_I

R9158 0 GIP

0 GIP

CLK2

IC9103

MAX17113ETL+ MINI_LVDS

FSEL

VIN

DEV

IN2

EAN60924401

OUT

7 8 9 10

VGL (-5V)

C9123 1uF 10V

R9115 R9116 10 10 GIP GIP

VCC_LCM (+3.3V)

REF R9135 3.6K

VGH (+25V)

TCON_42_FHD R9144 1%

C9118 10uF 16V

27K

VGL (-5V)

VGL_FB R9145

R9171

PANEL_VCC (+12V)

R9194 360 OPT

0 C9147 1uF 50V

R9173 1K

C9152 1uF 10V

C9155 22uF 25V

C9162 22uF 25V

R9174 OPT

C9124 1uF 50V

D9102 KDS226

TCON_42_FHD

C9164 0.47uF 16V

C9151 0.1uF 50V

C9149 22uF 10V

C9146 150pF 50V

D9105 MBRA340T3G 40V

C9154 OPT

R9181 5.1K

OPT

C9137-*1 1uF 10V NON_GIP

C9127

150K

2.8A

0.1uF 50V

C9137 0.1uF 50V GIP

OPT R9151 0

R9149 0

L9101 22UH

C9140

REF

VGL_FB

R9114 OPT OPT

C9107 1uF 50V GIP

R9180 360

VCC_LCM (+3.3V)

FLK R9111 10 GIP

PANEL_VCC (+12V)

C9143 0.1uF 50V

R9167 0 NON_GIP

R9110 22 GIP C9104 1uF 50V GIP

560pF 50V NON_GIP

1000pF 50V GIP

C9144 0.1uF 50V

CLK1 R9105 22 GIP

1/8W

C9145-*1

C9145

EN2

EN1

R9148 510 NON_GIP C9125 68pF

VDD_LCM (+16V)

R9131 11K 1% TCON_42_FHD

C9101 VGH 0.22uF (+25V) 50V GIP

EN2

LX2

220K 1% TCON_42_FHD Value should be checked VGH_FB

R9133 R9134 10 10 GIP GIP

GND2

LX2

56K 1% TCON_42_FHD R9130

DRVP

SRC 0 GIP GON 0 GIP R9155 DRN 510 NON_GIP MODE NON_GIP DLP

R9154 R9150

BST

0.47uF 25V

FB2

C9117 1uF 50V

DEL1

CLK3

C9122

C9116 1uF 50V

PGND

CLK4

GON2

GOFF

GON1

GCLK3_I

18K

EAN60987201 11

DEV

A4 GCLK4_I

18K

CLK5

R9129

REF

MINI_LVDS C9112 4.7uF 50V

R9124 R9125

THR

R9153 0 NON_GIP

FBN

GIP

VST CLK6

D9101 KDS226

R9132

100V OPT

4.7uF/50V(3216)

9.1K

C9148 22uF 25V

2.8A

2.2

EN2

VDD_EVEN

R9182

L9102 22UH

R9169

10K GIP

IC9101 MAX17119DS

VDD_ODD

1000pF 50V GIP

CTL

GND

YDCHG 22

FLK2

FLK1

FLK3

MBRA340T3G MBRA340T3G

R9168

C9128

VGH R9147 2.7K NON_GIP (+25V) VGH_M R9152 0 (+25V) NON_GIP

D9106 D9104

AGND

A5 GCLK5_I

TH9000

47k-ohm

A6 GCLK6_I

THERMAL 29

R9147-*1 0 GIP

D9100 MMSD4148T1G

GIP NCP18WB473F10RB

A7 GVST_I/GSP

EP[VGOFF]

VSENSE 28

A9 GVDD_ODD_I/GSC

C9136 27pF 50V NON_GIP

R9146 33K NON_GIP

VGH (+25V)

C9142 1uF 50V

25V 47uF C9141

1uF 50V

C9150 1uF 50V

TCON_42_FHD

C9128-*1 470pF 50V NON_GIP

R9113 10K GIP

C9135 OPT

R9166 15K 1%

DRVN

FLK

DISCHG

VDD_LCM (+16V)

GVDD_EVEN_I/GOE

R9157 75K 1%

R9168-*1

To reduce Audible noise C9153 100uF 25V

C9138

C9139 R9109 3K GIP

C9102 OPT OPT

VDD_LCM (+16V)

EN2 100V

* Voltage Target VDD_LCM = 16.25V VGH = 28.50V VGL = -5.35V

1uF 50V

R9170 DPM

EN2 10

[P-GAMMA Block]

R9172

GMA16

VDD_LCM (+16V)

VCOMLFB

SW_1

SW_2

PGND_2

R9123 1M NON_GIP

VCOM_FB0

12505WS-03A00

VIN_2

16 1

VIN_1

DEV IC9102

GND_2

GND_1

TPS62110RSAR 10 MINI_LVDS 9

R9126 510K

C9113 22pF 50V

C9114 22uF 16V

C9115 10uF 16V

R9193

SDA3_3.3V

R9102 1K 1% TCON_42_FHD

R9106 VCOMR 0 R9107

GCLK5_I

GCLK5 GIP

VGH (+25V)

C9158 15pF 50V OPT

R9140 GIP

FB AGND

VGI_N R9162 0

EAN60985901

R9127 150K TCON_42_FHD

GCLK3_I

GCLK3

VGL (-5V)

R9128 200K TCON_42_FHD 1%

R9178 0

GCLK6_I

GCLK6

C9131 15pF 50V NON_GIP

R9141

GIP

C9159 15pF 50V OPT

R9142 VGL_I 0 OPT GVDD_ODD/GSC

R9163 0

GVDD_ODD_I/GSC

DPM_A

R9179 DPM 0

100V

C9132 15pF 50V

C9111 1uF 50V POL_A

C9157 15pF 50V

R9177 0

R9195

2.2K 2.2K MINI_LVDSMINI_LVDS

PANEL_VCC SCL3_3.3V

GCLK4_I GIP

GCLK1_I C9130 15pF 50V NON_GIP

VGI_P

GIP

R9122 10

MMSD4148T1G

R9176 0

OPT R9139

Vo = 1.153*(1+R1/R2)

24K

EN2 D9108

OPT

GCLK4/OPT_P

C9110 1uF 25V

For P-Gamma Data Download P9100

R9160 0

C9156 15pF 50V

R9161 0

LG5111 SWAP

DISCHG R9196

GIP C9129 15pF 50V NON_GIP

NON_GIP

VINA

R9118

PGND_1

R9117 47K OPT

GCLK1/GSP_R

TCON_42_FHD

LBI

C9105 0.1uF 50V

10K OPT VCOMRFB

C9109 10uF 25V

MINI_LVDS

C9103 0.1uF 50V

HVDD

C9108 10uF 25V

C9119 15pF 50V NON_GIP

GCLK2_I

GCLK2

GIP R9121 0 GIP

10uF/25V(3216) MINI_LVDS VDD_LCM (+16V)

GVST_I/GSP GIP

VGL (-5V)

GMA6 GMA4

R9175 0

R9159 0

MINI_LVDS

LBO

AVDD_AMP

GMA2

GMA3

R9104 1K TCON_42_FHD

VCOM_FB

GMA3

GMA7

SYNC

DEV

L9103 BLM18PG121SN1D

NC_2

AVDD_2 16

GMA7

GMA8

MINI_LVDS

R9101 1K OPT

VCOM_FB0

GMA4

GMA12 OPT

IC9100 13 MAX9668ETP+

GMA13

6.8uH/1.8A (6x6x2mm) L9100 6.8uH

PANEL_VCC (+12V)

VDD_LCM (+16V)

VCOM

GMA5

AGND_AMP

GMA6

GVST/GSP

FLK 10 NON_GIP

MINI_LVDS

VCOM

R9136

FLK_A

GMA1

C9100 0.1uF 50V

R9143 3.3K GIP

10 1/8W

C9106 1uF 50V

15 THERMAL 21

NC_1

DVDD

SDA

AVDD_1

VCC_LCM (+3.3V)

1uF/50V(2012) R9112

R9103 R9100

SCL

EP[GND] SDA3_3.3V

VCC_LCM (+3.3V)

Signal Name Change

[HVDD Block]

To reduce Audible noise

L9104 BLM18PG121SN1D

SCL3_3.3V

GMA15

Slave Address : 0xE8h (AO Pin - GND)

OPT

R9137 POL 0

R9119 20K

C9160 15pF 50V

C9120 15pF 50V

GVDD_EVEN/GOE

R9164 0

GVDD_EVEN_I/GOE C9133 15pF 50V

R9120 7.5K SOE_A

OPT

R9138 SOE 0 C9121 15pF 50V

VCOML

VCOM 0

COMMON T-Con (L.D.)

09/09/10 95

32_FHD VGH R9129-*1 22K 1% TCON_32_FHD

VGL R9130-*1 220K 1% TCON_32_FHD

R9131-*1 11K 1% TCON_32_FHD

VDD R9156-*1 150K 1% TCON_32_FHD

R9157-*1 27K 1% TCON_32_FHD

R9129-*2 47K 1% TCON_37_FHD

R9145-*1 270K 1% TCON_32_FHD

R9131-*2 12K 1% TCON_37_FHD

R9166-*1 24K 1% TCON_32_FHD

R9126-*1 510K 1% TCON_32_FHD

R9127-*1 150K 1% TCON_32_FHD

R9128-*1 200K 1% TCON_32_FHD

91 or 95 Sheet

VDD

HVDD R9165-*2 470K 1% TCON_37_FHD

R9157-*2 56K 1% TCON_37_FHD

R9166-*2 56K 1% TCON_37_FHD

R9126-*2 470K 1% TCON_37_FHD R9128 OPEN R9127-*2 91K 1% TCON_37_FHD

91 or 95 Sheet

HVDD

91 or 95 Sheet

VCOM FEED BACK

R9104-*2 1K 1% TCON_37_FHD

91 or 95 Sheet

55_FHD VGL R9130-*3 220K 1% TCON_47_FHD

R9131-*3 11K 1% TCON_47_FHD

VDD

R9129-*4 510K 1% TCON_55_FHD

R9145-*3 270K 1% TCON_47_FHD

R9131-*4 27K 1% TCON_55_FHD

HVDD R9165 OPEN

R9166-*3 20K 1% TCON_47_FHD

R9130-*4 68K 1% TCON_55_FHD

R9156-*4 150K 1% TCON_55_FHD R9128-*3 220K 1% TCON_47_FHD

R9104-*3 1K 1% TCON_47_FHD

R9102-*3 1K 1% TCON_47_FHD

R9157-*4 75K 1% TCON_55_FHD

R9144-*4 27K 1% TCON_55_FHD R9145-*4 150K 1% TCON_55_FHD

HVDD

VDD

R9126-*3 510K 1% TCON_47_FHD

R9127-*3 150K 1% TCON_47_FHD

VGL

VGH

R9144-*3 51K 1% TCON_47_FHD

VCOM FEED BACK R9101-*3 1K 1% TCON_47_FHD

VGL

TCON_37_FHD

R9102-*2 1.5K 5% TCON_37_FHD

VGH

R9157-*3 75K 1% TCON_47_FHD

R9145-*2 150K 1%

R9156-*2 910K 1% TCON_37_FHD

R9101-*2 1K 1% TCON_37_FHD

47_FHD

R9156-*3 180K 1% TCON_47_FHD

91 or 95 Sheet

R9144-*2 20K 1% TCON_37_FHD

VCOM FEED BACK

R9104-*1 1K 1% TCON_32_FHD

R9102-*1 1K 1% TCON_32_FHD

R9129-*3 51K 1% TCON_47_FHD

R9130-*2 220K 1% TCON_37_FHD

VDD

HVDD R9165 OPEN

VGH

VGL

VGH

R9144-*1 51K 1% TCON_32_FHD

VCOM FEED BACK R9101-*1 1K 1% TCON_32_FHD

42_FHD

37_FHD

R9165 OPEN

R9166-*4 15K 1% TCON_55_FHD

R9126-*4 180K 1% TCON_55_FHD

R9127-*4 68K 1% TCON_55_FHD

R9128-*4 56K 1% TCON_55_FHD

VCOM FEED BACK R9101 OPEN

R9104 OPEN

R9102-*4 0 5% TCON_55_FHD

Common T-Con Power Option

09/12/15 98

LCD TV Repair Guide `10 years New Models

< Applicable Model > xxLE5500,xxLE7500, xxLE8500

LGE Internal Use Only

Overview for â&#x20AC;&#x2122;10 Broadband Model (Hardware)

LGE Internal Use Only

Features LED LCD TV Key Features LE5300 LE5300

LE5500 LE5500

LE7500 LE7500

LE8500 LE8500

LE9500 LE9500

Channel Browser

Limitless LimitlessJoy Joy by Contents by Contents

THX Broadband TV DLNA

Seamless Seamless Freedom Freedom by byConnectivity Connectivity

Wireless Ready Bluetooth USB (DivX HD, MP3, Jpeg play)

Borderless BorderlessVision Vision By Design By Design

Borderless Light

Borderless Slim Bezel & Depth Local Dimming (without 32/37”)

Cutting-Edge Cutting-Edge Picture PictureQuality Quality LED / Hz LED / Hz

LED (Edge)

Full LED Slim (IOP)

100Hz

200Hz

400Hz

FHD

LGE Internal Use Only

2 types of LED - IOP Benefit: More Clear More Real Feature Model

IOP Type

LE8500

Slim Not only Direct LED’s Picture Full LED quality, but Edge LED’s thin thickness Local Local Dimming depicts more Dimming deep Black color

Local Dimming LED Chip

inch

Local Dimming Block quantity

8 row * 24(3 ass’y*8) = 192EA

9 row * 24 = 216EA

10 row * 24 = 240EA

LED Package Upper Metal Cover LED BLU LGP Reflector Sheet Structure Array Lower Metal Cover Module Bezel 폭: 47LE9500 7mm 47LE8500

27 BLU A’ssy (864 LED Packages)

14mm

LED Package inch

Local Dimming Full LED

LED package quantity

192 * 4 packages/block = 768EA

216 * 4 packages/block = 864EA

240 * 5 packages/block = 1200EA

216 Local Dimming Blocks

LGE Internal Use Only

2 types of LED - Edge Benefit: More Clear More Real

Edge Type w/ Local Dimming Feature Edge LED Best picture quality + thin TV

LED Array

BLU structure

LED Packages

Upper Metal Cover

Local dimming depicts more Local Dimming deep black.

- 47” 264 - 42” 228

Model LED Array is on the Top & Bottom of Module

LE7500, LE5500

Local Dimming

12 Local Dimming Blocks

LGE Internal Use Only

Main PCB for Broadband

Main + TCON all in one

42”/47”/55”LE5500/7500, 42”/47LE8500 (with Local dimming) To LCD Module

32”LE5500/7500 (no Local dimming) 3

To PSU

LG5111 is not applied.

4 3 2

1 5

6 7

Main processor, DDR Memory Flash Memory LGE7378, Frame rate Converter (FRC) for 100Hz

Micom for Key/IR sensing

HDMI switch (4:1)

LG5111(Local Dimming Processor +LCD Timing Controller one Chip) Gamma, Vcom, Voltage generater For LCD Module

Audio AMP (10W+10W)

LGE Internal Use Only

BCM High Block Diagram (Input/Interface) RX MAX3232CDR IC8200

RS232 (P8201)

CVBS,L,R

AV1

YPbPr,L,R

COMP1

YPbPr,L,R

COMP2

WIRELESS_SCL/SDA=>AMP_SCL/SDA WIRELESS JK8700

Wireless_RX

EPHY_TDP/RDP

BCM_TXD1

Wireless_TX MC14053BDR2G IC8700

BCM_RXD1 BCM_TX

ETHERNET (JK8200)

EPHY_RDP/RDN

BCM_RX Wireless_DL_TX

DSUB_R/G/B, H/V_Sync

Wireless_DL_RX

IR_PASS

RGB_DDC_SCL/SDA

NEC_EEPROM _SCL/SDA

LED_B/LG LOGO IR

PC AUDIO IN (JK8401)

NEC_RXD

KEY2 LED_R/BUZZ

RGB-PC (P8400)

BCM3556

KEY1 CONTROL IR & KEY P8200

M24C02(EEPROM) IC8401

NEC_TXD

IC100

M_REMOTE_RX

MICOM UPD78F0513AGA -GAM-AX IC8101

M_REMOTE_TX

MOTION REMOCON P1700

BT_DM, BT_DP MICOM EEPROM M24C16-WMN6T 16Kbit IC8100

HDMI 1 HDMI 2 HDMI 3 HDMI 4

NEC_EEPROM _SCL/SDA

VREG_CTRL

BLUETOOTH P1895

CEC_REMOTE

HDMI0_ SCL/SDA, TMDS[0-2,CLK] HDMI1_ SCL/SDA, TMDS[0-2,CLK] HDMI2_ SCL/SDA, TMDS[0-2,CLK] HDMI3_ SCL/SDA, TMDS[0-2,CLK]

Brazil(ISDB) AUS/TW(DVB-T) TUNER HNIM/FNIM (TU2701)

Cable

BT_RESET

SUB_SCL/SDA

ATV/DTV TUNER (HNIM) TU2600

USB_DM1/2

TDA19997 4x1 HDMI Switch IC8300

TU_CVBS/TU_SIF

Internal Demod DVB-T

SIDE_USB _DP/DM

USB2512 IC2201

USB_DP1/2

USB P2201/2

FE_TS_SERIAL/SYNC/VAL_ERR/DATA_CLK

SCL1/SDA1 IF_AGC

IF_N / P

ISDB DEMOD MN884433 IC2800

Brazil OPT

LGE Internal Use Only

BCM High Block Diagram (Output/Audio) DPM_A => EN2

FRC_SPI

LVDS_TX_E/O[0-4]

I2C_SCL/SDA

DDR0 Data[0:15] DDR0 Address[0:13]

DDR1 Address[0:13] DDR1 Data[0:15]

IC100 NAND Flash (4Gbit) NAND04G_B2DN IC101

MINI_LVDS_POWER MAX17113 IC603

DDR0 Data[0:15] DDR0 Address[0:13]

DDR1 Data[0:15] SCL2/SDA2

AMP_SCL/SDA I2S

LLV[0-5]±, LCLK±

RLV[0-5]±, RCLK±

DDR2 SDRAM MT47H128M8HQ (1GBit) IC400/401 DDR2 SDRAM MT47H128M8HQ (1GBit) IC402/403

SCL1/SDA1

DDR2 SDRAM MT47H128M8HQ (1GBit) IC400/401

P-GAMMA for MINI-LVDS MAX9668ETP IC601

GMA[8 bit]

MINI_LVDS_POWER TPS62110 IC600

HVDD

DDR2 SDRAM MT47H128M8HQ (1GBit) IC402/403

Digital AMP (NTP7000) IC8801

PWM

LPF

SPDIF_OUT HP_L/R_+/-

Mini-LVDS P7400/1

SOE/POL/GSP/H_CONV/OPT_N, …

NAND_DATA[0:7]

DDR1 Address[0:13]

NVM M24M01-HRMN6TP 1Mbit IC102

VDD_LCM VCC_LCM

LEVEL SHIFT MAX17119ETI+ IC602

MST7378P (URSA3) IC9001

LVDS_E/O_CLK

BCM3556

DDR3 SDRAM H5TQ1G63BFR-12C (1GBit) IC8900 DDR3 Data[0:15]

DDR3 Address[0:12]

Serial Flash W25X40VSSIG IC9000

AMP KA4558D IC1100

P8800 (4pin)

JK8400 AUDIO OUT [SPDIF]

AUDIO OUT

HP_L/ROUT JK1101 AUDIO OUT [EARPHONE]

LGE Internal Use Only

BCM High Block Diagram (Memory)

FRC_SPI

LVDS_TX_E/O[0-4]

SCL1/SDA1

LVDS_E/O_CLK SCL1/SDA1

DDR3 SDRAM H5TQ1G63BFR-12C (1GBit) IC8900 DDR3 Data[0:15]

MICOM UPD78F0513AGA -GAM-AX IC8101

DDR3 Address[0:12]

Serial Flash W25L4005CM2I IC9000

LGE7378A (URSA3) IC9001

Mini-LVDS P7400/1

LLV[0-5]±, LCLK± SOE/POL/GSP/H_CONV/OPT_N, … RLV[0-5]±, RCLK±

NEC_EEPROM_SCL/SDA DDR0 Data[0:15] MICOM EEPROM M24C16-WMN6T 16Kbit IC8100

DDR0 Address[0:13]

BCM3556

DDR1 Address[0:13] DDR1 Data[0:15]

IC100 NAND Flash (4Gbit) NAND04G_B2DN IC101

DDR2 SDRAM MT47H128M8HQ (1GBit) IC402/403

NAND_DATA[0:7] DDR0 Data[0:15] DDR0 Address[0:13]

DDR1 Address[0:13] DDR1 Data[0:15] NVM M24M01-HRMN6TP 1Mbit IC102

DDR2 SDRAM MT47H128M8HQ (1GBit) IC400/401

SCL3/SDA3

DDR2 SDRAM MT47H128M8HQ (1GBit) IC400/401 DDR2 SDRAM MT47H128M8HQ (1GBit) IC402/403

LGE Internal Use Only

I2C Map

CH0 CH0 Tuner Tuner HNIM HNIM (TU2701) (TU2701)

CH1 CH1 MICOM MICOM NEC NEC (IC1002) (IC1002)

Audio Audio Amp. Amp. NTP7000 NTP7000 (IC501) (IC501)

FRC(URSA3) FRC(URSA3)

ISDB_DEMOD

MST7378 MST7378 (IC1300) (IC1300)

MN884433 (IC3701) 0xd8 (Brazil Only)

CH2 CH2 HDMI HDMI SW SW

USB2

TDA9996HL TDA9996HL (IC800) (IC800) 0xc0 0xc0

USB2512 (IC2201)

CH3 CH3

NVRAM NVRAM

P-Gamma P-Gamma

M24M01 M24M01 (IC102) (IC102)

MAX9668ETP MAX9668ETP (IC601) (IC601) 0xe8 0xe8

LGE Internal Use Only

I2C Map

CH0 CH0 Tuner Tuner HNIM HNIM (TU2701) (TU2701)

CH1 CH1 P-Gamma P-Gamma

HDMI HDMI SW SW

ISDB_DEMOD

MAX9668ETP MAX9668ETP (IC601) (IC601) 0xe8 0xe8

TDA9996HL TDA9996HL (IC800) (IC800) 0xc0 0xc0

MN884433 (IC3701) 0xd8

MICOM MICOM

Audio Audio Amp. Amp.

CH2 CH2 NEC NEC (IC1002) (IC1002)

NTP7000 NTP7000 (IC501) (IC501)

NVRAM NVRAM

FRC(URSA3) FRC(URSA3)

USB2 USB2512 (IC2201)

CH3 CH3 M24M01 M24M01 (IC102) (IC102)

MST7378 MST7378 (IC1300) (IC1300)

LGE Internal Use Only

Appendix. Block Diagram for Edge/IOP Backlight

Backlight Interface Signals (120Hz), To LED driver

Main Main SoC SoC

FRC FRC 50Hz

100Hz

LG5111 LG5111 (1920x1080P (1920x1080P @100Hz) @100Hz)

LCD LCD Panel Panel 100Hz 100Hz 100Hz

[ All in one main PCB for LE55 & LE75 edge & LE85 IOP LED Backlight] * LE85 series have TM240Hz function in LED Driver board of module.

LGE Internal Use Only

Interconnection - 1 [PCBs]

32/42/47/55LE7500, 32/42/47/55LE5500 LED driver

1 1 2

Main PCB

PSU + LED driver

Bluetooth PCB

LOGO PCB

Soft Touch Key PCB

IR/Sensor PCB

[Cables] 5

Main / PSU cable

Main / Module LVDS cable

LED driver / Module cable

BT shield cable

SPK cable

LOGO/Touch/IR cable

LCD Module

LGE Internal Use Only

Interconnection - 2 [PCBs]

55LE7500, 55LE5500 3

Main PCB

PSU

Bluetooth PCB

LOGO PCB

Soft Touch Key PCB

IR/Sensor PCB

LED driver

2 4

[Cables] 5

6 Main / PSU cable

Main / Module LVDS cable

LED driver / PSU cable

BT shield cable(not in picture)

SPK cable

LOGO/Touch/IR cable

Local dimming signal cable

3 LCD Module

LGE Internal Use Only

Interconnection - 4 [PCBs] 42/47LE8500 Col. 1

Col. 2

Col. 3

3 8

Main PCB

PSU

Bluetooth PCB

LOGO PCB

Soft Touch Key PCB

IR/Sensor PCB

LED driver master

LED driver slave

1 8 1

[Cables] 7 5

6 4

8 connection cables for each BLU Ass’y

Main / PSU cable

Main / Module LVDS cable

LED driver / PSU cable Master 14P, slave 12P

BT shield cable

SPK cable

LOGO/Touch/IR cable

Local dimming signal cable (Main / LED driver master)

Local dimming signal cable (Main / LED driver slave)

LGE Internal Use Only

Interconnection – sub PCB

IR/Sensor

SPK unit

S/T

Logo

To Main

LOGO/Touch/IR cable

LGE Internal Use Only

Contents of LCD TV Standard Repair Process No.

Error symptom (High category)

Error symptom (Mid category)

Page

No video/Normal audio

No video/No audio

Video error, video lag/stop

Color error

Vertical/Horizontal bar, residual image, light spot, external device color error

No power

Off when on, off while viewing, power auto on/off

No audio/Normal video

Wrecked audio/discontinuation/noise

No response in remote controller, key error, recording error, memory error

External device recognition error

A. Video error

B. Power error

Remarks

C. Audio error

D. Function error 11 12

E. Noise

Circuit noise, mechanical noise

F. Exterior error

Exterior defect

LGE Internal Use Only

Standard Repair Process

Error symptom

LCD TV

A. Video error

Established date

No video/ Normal audio

Revised date

2010. 2 .19 1/13

First of all, Check whether all of cables between board is inserted properly or not. (Main B/D↔ Power B/D, LVDS Cable,Speaker Cable,IR B/D Cable,,,) ☞A1 No video Normal audio

Normal audio

☞A4

Check Back Light On with naked eye

N Move to No video/No audio

Check Power Board 12v,5v etc.

☞A2

Check Power Board 20V /12V or 24v output

Normal voltage

Replace T-con Board or module And Adjust VCOM

☞A28

Repair Power Board or parts

Replace Inverter or module End

N Repair Power Board or parts

※Precaution

☞A7 & A3

Always check & record S/W Version and White Balance value before replacing the Main Board

Replace Main Board

Re-enter White Balance value

LGE Internal Use Only

Standard Repair Process

LCD TV

Error symptom

A. Video error

Established date

No video/ No audio

Revised date

2010. 2 .19 2/13

☞A4 No Video/ No audio

Check various voltages of Power Board ( 5V,12V,20V or 24V…)

Normal voltage?

Check and replace MAIN B/D End

Replace Power Board and repair parts

LGE Internal Use Only

Standard Repair Process

Error symptom

LCD TV

☞ A6 Check RF Signal level

Normal Signal?

A. Picture Problem

Established date

Picture broken/ Freezing

Revised date

3/13

. By using Digital signal level meter . By using Diagnostics menu on OSD ( Menu→Red key→Signal test) - Signal strength (Normal : over 50%) - Signal Quality (Normal: over 50%)

Check whether other equipments have problem or not. (By connecting RF Cable at other equipment) → DVD Player ,Set-Top-Box, Different maker TV etc`

■ Menu→Setup →Booster

☞ A7 Check RF Cable Connection 1. Reconnection 2. Install Booster

Normal Picture?

Check S/W Version

SVC Bulletin?

N Normal Picture?

2010. 2 .19

S/W Upgrade

Normal Picture?

N Check Tuner soldering

Contact with signal distributor or broadcaster (Cable or Air) Normal Picture?

Booster menu On→Off: Check Off→On: Check

N Replace Main B/D

Y Close Close

LGE Internal Use Only

Standard Repair Process

LCD TV

Error symptom

☞A8 Check color by input -External Input -COMPONENT -RGB -HDMI/DVI

A. Video error

Established date

Color error

Revised date

Check Test pattern

4/13

☞ A10/ A11

Color error? N

※ Check and replace Link Cable (LVDS) and contact condition

Y Color error?

Color error?

Replace Main B/D

Replace module

N End

Check error color input mode

☞A12

2010. 2 .19

External Input/ Component error

Check external device and cable

External device Y /Cable normal

Replace Main B/D

N Request repair for external device/cable N RGB/ HDMI/DVI error

Check external device and cable

External device Y /Cable normal

Replace Main B/D

LGE Internal Use Only

Standard Repair Process

LCD TV

Error symptom

A. Video error

Established date

Vertical / Horizontal bar, residual image, light spot, external device color error

Revised date

2010. 2 .19 5/13

Vertical/Horizontal bar, residual image, light spot ☞A8

Replace Module

☞ A10/ A11

Check color condition by input -External Input -Component -RGB -HDMI/DVI

Screen Y normal?

Check external device connection condition

Y Normal? N

☞ A28 Screen N normal?

Request repair for external device

Replace module

☞A12

Check and replace Link Cable

End

Screen normal?

Replace Main B/D (adjust VCOM)

For LGD panel

Replace Main B/D

End

For other panel

Check Test pattern

External device screen error-Color error Check S/W Version

Check N version Y

External Input error Component error

S/W Upgrade

Normal screen?

Check screen condition by input -External Input -Component -RGB -HDMI/DVI

RGB error

HDMI/ DVI

Connect other external device and cable (Check normal operation of External Input, Component, RGB and HDMI/DVI by connecting Jig, pattern Generator ,Set-top Box etc.

N Screen normal?

Replace Main B/D

Y Request repair for external device Y Screen normal?

Replace Main B/D

5 LGE Internal Use Only

Standard Repair Process

LCD TV

Error symptom

B. Power error

Established date

No power

Revised date

☞A17 Check Power LED

. Stand-By: Red . Operating: white

2010. 2 .19 6/13

☞A19 DC Power on by pressing Power Key On Remote control

Power LED On? N

Normal N operation?

Check Power On ‘”High”

OK?

Replace Power B/D

Check Power cord was inserted properly

Replace Main B/D

☞A4 Measure voltage of each output of Power B/D

N Normal?

※ Check ST-BY 5V

Normal Y voltage?

☞A18

Normal voltage?

Replace Main B/D

N Replace Power B/D

Replace Power B/D

LGE Internal Use Only

Standard Repair Process

LCD TV

Error symptom

B. Power error

Established date

Off when on, off while viewing, power auto on/off

Revised date

2010. 2 .19 7/13

Check outlet

☞A22 Error?

Check A/C cord

Check Power Off Mode

CPU Abnormal

Normal?

Replace Main B/D

End

N Check for all 3- phase power out

Abnormal 1

☞A19

Fix A/C cord & Outlet and check each 3 phase out

(If Power Off mode is not displayed) Check Power B/D voltage ※ Caution Check and fix exterior of Power B/D Part

* Please refer to the all cases which can be displayed on power off mode.

Replace Power B/D

Status

Normal voltage?

Replace Main B/D

N Replace Power B/D

Power off List "POWEROFF_REMOTEKEY" "POWEROFF_OFFTIMER" "POWEROFF_SLEEPTIMER" "POWEROFF_INSTOP" "POWEROFF_AUTOOFF" Normal "POWEROFF_ONTIMER" "POWEROFF_RS232C" "POWEROFF_RESREC" "POWEROFF_RECEND" "POWEROFF_SWDOWN" "POWEROFF_UNKNOWN" "POWEROFF_ABNORMAL1" Abnormal "POWEROFF_CPUABNORMAL"

Explanation Power off by REMOTE CONTROL Power off by OFF TIMER Power off by SLEEP TIMER Power off by INSTOP KEY Power off by AUTO OFF Power off by ON TIMER Power off by RS232C Power off by Reservated Record Power off by End of Recording Power off by S/W Download Power off by unknown status except listed case Power off by abnormal status except CPU trouble Power off by CPU Abnormal

LGE Internal Use Only

Standard Repair Process

LCD TV

Error symptom

C. Audio error

Established date

No audio/ Normal video

Revised date

☞A24 No audio Screen normal

Check user menu > Speaker off

2010. 2 .19 8/13

☞A25 N Off

Check audio B+ 20V or 24V of Power Board

Normal voltage

Cancel OFF

Check Speaker disconnection

Replace Power Board and repair parts

N Disconnection

Replace MAIN Board

End

Y Replace Speaker

LGE Internal Use Only

Standard Repair Process

LCD TV

Error symptom

C. Audio error

Established date

Wrecked audio/ discontinuation/noise

Revised date

2010. 2 .19 9/13

→ abnormal audio/discontinuation/noise is same after “Check input signal” compared to No audio ☞A25

Check input signal -RF -External Input signal

Wrecked audio/ Discontinuation/ Noise for all audio Signal normal?

Check and replace speaker and connector

Check audio B+ Voltage (20V or 24V)

Y Wrecked audio/ Discontinuation/ Noise only for D-TV

Normal voltage?

Replace Main B/D N

Wrecked audio/ Discontinuation/ Noise only for Analog (When RF signal is not received) Request repair to external cable/ANT provider (In case of External Input signal error) Check and fix external device

Replace Power B/D

Replace Main B/D

Wrecked audio/ Discontinuation/ Noise only for External Input Connect and check other external device

Normal audio?

End

Y Check and fix external device

LGE Internal Use Only

Standard Repair Process

Error symptom

LCD TV

D. General Function Problem

Established date

Remote control & Local switch checking

Revised date

2010. 2 .19 10/13

1. Remote control(R/C) operating error

Replace Main B/D

☞A27 Check R/C itself Operation

Normal Y operating? N

Normal operating?

Check R/C Operating When turn off light in room

Check & Replace Baterry of R/C

If R/C operate, Explain the customer cause is interference from light in room.

Normal operating?

☞A27

Check & Repair Cable connection Connector solder

Check B+ 5V On Main B/D

☞A4

Normal Voltage?

Check IR Output signal

Check 5v on Power B/D Replace Power B/D or Replace Main B/D (Power B/D don’t have problem)

Normal Signal? N Repair/Replace IR B/D

N Replace R/C

LGE Internal Use Only

Standard Repair Process

LCD TV

Check input signal

Error symptom

Y Signal input? N

D. Function error

Established date

External device recognition error

Revised date

Check technical information - Fix information - S/W Version

Check and fix external device/cable

Technical information?

External Input and Component Recognition error

2010. 2 .19 11/13

Replace Main B/D

Fix in accordance with technical information

RGB,HDMI/ DVI, Optical Recognition error

Replace Main B/D

LGE Internal Use Only

Standard Repair Process

LCD TV

Identify nose type

Error symptom

E. Noise

Established date

Circuit noise, mechanical noise

Revised date

Circuit noise

Check location of noise

Mechanical noise

Check location of noise

2010. 2 .19 12/13

Replace PSU(with LED driver) OR Replace LED driver

※ When the nose is severe, replace the module (For models with fix information, upgrade the S/W or provide the description)

※ Mechanical noise is a natural phenomenon, and apply the 1st level description. When the customer does not agree, apply the process by stage. ※ Describe the basis of the description in “Part related to nose” in the Owner’s Manual.

※ If there is a “Tak Tak” noise from the cabinet, refer to the KMS fix information and then proceed as shown in the solution manual (For models without any fix information, provide the description)

LGE Internal Use Only

Standard Repair Process

LCD TV

F. Exterior defect

Error symptom

Zoom part with exterior damage

Exterior defect

Module damage

Replace module

Established date Revised date

2010. 2 .19 13/13

Adjust VCOM

â&#x2DC;&#x17E;A28 Cabinet damage Remote controller damage

Stand dent

Replace cabinet

Replace remote controller

Replace stand

LGE Internal Use Only

Contents of LCD TV Standard Repair Process Detail Technical Manual No.

Error symptom

Content

Page

Check LCD back light with naked eye

LED driver B+ 24V measuring method

Check White Balance value

Power Board voltage measuring method

TUNER input signal strength checking method

LCD-TV Version checking method

LCD TV connection diagram

Tuner Checking Part

Check Link Cable (LVDS) reconnection condition

A10

Adjustment Test pattern - ADJ Key

A12

LCD TV connection diagram

Check Link Cable (LVDS) reconnection condition

A10

Adjustment Test pattern - ADJ Key

A12

Exchange T-Con Board (1)

A-1/5

Exchange T-Con Board (2)

A-2/5

Exchange LED driver Board (PSU)

A-3/5

Exchange Module itself (1)

A-4/5

Exchange Module itself (2)

A-5/5

Remarks

A. Video error_ No video/Normal audio

6 A. Video error_ No video/Video lag/stop

A. Video error_Color error

A. Video error_Vertical/Horizontal bar, residual image, light spot

17 18

<Appendix> Defected Type caused by T-Con/ Inverter/ Module

A10 : 32/42/47/55

55â&#x20AC;? : driver board Other : PSU

LGE Internal Use Only

Contents of LCD TV Standard Repair Process Detail Technical Manual Continued from previous page No.

Error symptom

Content

Page

Check front display LED

A17

Check power input Voltage & ST-BY 5V

A18

Checking method when power is ON

A19

POWER BOARD voltage measuring method

B. Power error_No power

Remarks

25 26

B. Power error_Off when on, off while viewing

POWER OFF MODE checking method

A22

B. Power error_Off when on, off while viewing

POWER BOARD PIN voltage checking method

A19

Checking method in menu when there is no audio

A24

Voltage and speaker checking method when there is no audio

A25

28 C. Audio error_No audio/Normal video 29 30

C. Audio error_Wrecked audio/discontinuation

Voltage and speaker checking method in case of audio error

A25

D. Function error_ No response in remote controller, key error

Remote controller operation checking method

A27

D. VCOM Adjustment

Sequence of the Vcom adjustment

A28

LGE Internal Use Only

Standard Repair Process Detail Technical Manual LCD TV

Error symptom Content

A. Video error_No video/Normal audio Check LCD back light with naked eye

Established date Revised date

2010. 2 .19 A1

After turning on the power and disassembling the case, check with the naked eye, whether you can see light from 4 locations. A1 Copyright â&#x201C;&#x2019; 2010 LG Electronics. Inc. All right reserved. Only for training and service purposes

LGE Internal Use Only

Standard Repair Process Detail Technical Manual LCD TV

Error symptom

A. Video error_No video/Normal audio

Content

LED driver B+ 24V measuring method

Established date Revised date

2010. 2 .19 A2

Check the DC 20V/24V, 12V, 3.5V and Inverter on

P204

IOP 42”/47”, Edge LED 55” P205 1~5

24V

6~10

GND

PWM Dim #1

Inverter ON

1~5

24V

6~10

GND

PWM Dim #1 (Edge LED : NC)

Inverter ON

NC (Edge LED:PWM Dim#1)

Error

* 14

Edge LED 32/42/47”

: For LE85 GND

LGE Internal Use Only

Standard Repair Process Detail Technical Manual LCD TV

Error symptom

A. Video error_No video/Normal audio

Content

Check White Balance value

Established date Revised date

2010. 2 .19 A4

Entry method method Entry 1. 1. Press Press the the ADJ ADJ button button on on the the remote remote controller controller for for adjustment. adjustment. 2. Enter Enter into into White White Balance Balance of of item item 7. 6. 2. 3. 3. After After recording recording the the R, R, G, G, B B (GAIN, (GAIN, Cut) Cut) value value of of Color Color Temp Temp (Cool/Medium/Warm), (Cool/Medium/Warm), rereenter the the value value after after replacing replacing the the MAIN MAIN BOARD. BOARD. enter

LGE Internal Use Only

Standard Repair Process Detail Technical Manual LCD TV

Error symptom

A. Video error_No video/ Audio

Content

Power Board voltage measuring method

Established date Revised date

2010. 2 .19 A5

Check the DC 20V/24V, 12V, 3.5V.

IOP 47”/Edge LED 55”

3 5 7 9 11 13 15 17 19

Edge LED 32/42/47” 21 23

Pin layout (24P) 24V (IOP & Edge 55”) Power 2 on 20V (Edge 42/47) 24V 4 24V GND 6 GND GND 8 GND 3.5V 10 3.5V 3.5V 12 3.5V GND 14 GND GND 16 NC 12V 18 Inverter ON LE : NC 12V 20 IOP : PWM Dim #1 LE : PWM Dim #1 12V 22 IOP : NC NC 24 Error-out

LGE Internal Use Only

Standard Repair Process Detail Technical Manual LCD TV

Error symptom Content

A. Video error_Video error, video lag/stop TUNER input signal strength checking method

Established date Revised date

2010. 2 .19 A6

MENU -Æ red key(customer support -Æ signal test -Æ select channel

When the signal is strong, use the attenuator (-10dB, -15dB, -20dB etc.)

LGE Internal Use Only

Standard Repair Process Detail Technical Manual LCD TV

Error symptom Content

A. Video error_Video error, video lag/stop LCD-TV Version checking method

Established date Revised date

2010. 2 .19 A7

1. Checking method for remote controller for adjustment

Version

Press the IN-START with the remote controller for adjustment

LGE Internal Use Only

Standard Repair Process Detail Technical Manual LCD TV

Error symptom Content

A. Video error _Vertical/Horizontal bar, residual image, light spot LCD TV connection diagram (1)

Established date Revised date

2010. 2 .19 A8

8 2

1 3 9

4 As the part connecting to the external input, check the screen condition by signal 7

5 6

LGE Internal Use Only

Standard Repair Process Detail Technical Manual LCD TV

Error symptom Content

A. Video error_Video error, video lag/stop TUNER checking part

Established date Revised date

2010. 2 .19 A9

Checking method: 1. Check the signal strength or check whether the screen is normal when the external device is connected. 2. After measuring each voltage from power supply, finally replace the MAIN BOARD.

LGE Internal Use Only

Standard Repair Process Detail Technical Manual LCD TV

Error symptom Content

A. Video error_Color error Check Link Cable (LVDS) reconnection condition

Established date Revised date

2010. 2 .19 A10

<32/42/47/55LE7500_LE5500>

LGE Internal Use Only

Standard Repair Process Detail Technical Manual LCD TV

Error symptom Content

A. Video error_Color error Adjustment Test pattern - ADJ Key

Established date Revised date

2010. 2 .19 A12

You can view 6 types of patterns using the ADJ Key Checking item : 1. Defective pixel 2. Residual image 3. MODULE error (ADD-BAR,SCAN BAR..) 4.Video error (Classification of MODULE or Main-B/D!) A12 Copyright â&#x201C;&#x2019; 2010 LG Electronics. Inc. All right reserved. Only for training and service purposes

LGE Internal Use Only

Appendix : Exchange T-Con Board (1)

Solder defect, CNT Broken

T-Con T-Con Defect, Defect, CNT CNT Broken Broken Solder defect,CNT CNTBroken Broken T-Con Defect,

Abnormal Power Section

Solder defect, Short/Crack

Abnormal Power Section

Solder defect, Short/Crack

LGE Internal Use Only

Appendix : Exchange T-Con Board (2)

Abnormal Power Section

Solder defect, Short/Crack

GRADATION

Abnormal Power Section

Solder defect, Short/Crack

Fuse Open, Abnormal power section

Abnormal Display

Noise

GRADATION

LGE Internal Use Only

Appendix : Exchange PSU(LED driver)

No Light

Dim Light

LGE Internal Use Only

Appendix : Exchange the Module (1)

Panel Mura, Light leakage

Crosstalk

Panel Mura, Light leakage

Press damage

Crosstalk

Un-repairable Cases In this case please exchange the module.

LGE Internal Use Only

Appendix : Exchange the Module (2)

Vertical Block Source TAB IC Defect

Horizontal Block Gate TAB IC Defect

Vertical Line Source TAB IC Defect

Horizontal Gate TAB ICBlock Defect Gate TAB IC Defect

Vertical Block Source TAB IC Defect

Horizontal line Gate TAB IC Defect Gate TAB IC Defect

Un-repairable Cases In this case please exchange the module. Horizontal Block Gate TAB IC Defect Gate TAB IC Defect A - 5/5 Copyright â&#x201C;&#x2019; 2010 LG Electronics. Inc. All right reserved. Only for training and service purposes

LGE Internal Use Only

Standard Repair Process Detail Technical Manual LCD TV

Error symptom

B. Power error _No power

Content

Check front display LED

Established date Revised date

2010. 2 .19 A17

Front LED control : Menu Æ Option Æ Power Indicator Æ Standby light ON

ST-BY condition: Red Power ON condition: white

LGE Internal Use Only

Standard Repair Process Detail Technical Manual LCD TV

Error symptom Content

B. Power error _No power Check power input voltage and ST-BY 5V

Established date Revised date

2010. 2 .19 A18

For ’10 models, there is no voltage out for st-by purpose. When st-by, only 3.5V is normally on.

Check the 3.5V when st-by

IOP 47”/Edge LED 55”

3 5 7 9 11 13 15 17 19

Edge LED 32/42/47”

21 23

A18 LGE Internal Use Only

Standard Repair Process Detail Technical Manual LCD TV

Error symptom Content

B. Power error _No power Checking method when power is ON

Established date Revised date

2010. 2 .19 A19

Check “power on” pin is high

IOP 47”/Edge LED 55” 1 3 5 7 9 11 13 15 17

Edge LED 32/42/47”

19 21 23

LGE Internal Use Only

Standard Repair Process Detail Technical Manual LCD TV

Error symptom Content

B. Power error _Off when on, off whiling viewing POWER OFF MODE checking method

Established date Revised date

2010. 2 .19 A22

Entry method 1. Press the IN-START button of the remote controller for adjustment 2. Check the entry into adjustment item 3

LGE Internal Use Only

Standard Repair Process Detail Technical Manual LCD TV

Error symptom Content

C. Audio error_No audio/Normal video Checking method in menu when there is no audio

Established date Revised date

2010. 2 .19 A24

Checking method 1. Press the MENU button on the remote controller 2. Select the AUDIO function of the Menu 3. Select TV Speaker from Off to On

LGE Internal Use Only

Standard Repair Process Detail Technical Manual LCD TV

Error symptom

C. Audio error_No audio/Normal video

Content

Voltage and speaker checking method when there is no audio

Established date Revised date

2010. 2 .19 A25

②

1 3 5 7 9 11 13 15 17

Edge LED 32/42/47”

19 21 23

①

③

Checking order when there is no audio ① Check the contact condition of 20V or 24V connector of Main Board ② Measure the 24V input voltage supplied from Power Board (If there is no input voltage, remove and check the connector) ③ Connect the tester RX1 to the speaker terminal and if you hear the Chik Chik sound when you touch the GND and output terminal, the speaker is normal.

LGE Internal Use Only

Standard Repair Process Detail Technical Manual LCD TV

Error D. Function error_ No response in remote controller, symptom key error Content

Remote controller operation checking method

Established date Revised date

2010. 2 .19 A27

1 2 3 4 5 6 7 8 9

P8200 SCL SDA GND KEY1 KEY2 St 3.3V GND LED_B IR

GND

Normal 3.3V

LED_R

Checking order 1, 2. Check IR cable condition between IR & Main board. 3. Check the st-by 3.3V on the terminal 6. 4. When checking the Pre-Amp when the power is in ON condition, it is normal when the Analog Tester needle moves slowly, and defective when it does not move at all.

LGE Internal Use Only

Standard Repair Process Detail Technical Manual LCD TV

Error symptom

D. VCOM Adjustment

Content

Sequence of the Vcom adjustment

Established date Revised date

2010. 2 .19 A28

1. Case ■ LCD module change ■ T-Con board change

2. Equipment ■ Service Remote controller

3. Adjust sequence ■ Press the ‘adj’ key ■ select V-COM ■ As pushing the right or the left button on the remote controller, And find the V-COM value Which is no or minimized the Flicker. (If there is no flicker at default value, Press the exit key and finish the VCOM adjustment.) ■ Push the OK key to store the value. Then the message “Saving OK” is pop. ■ Press the exit key to finish V-COM adjustment.

LGE Internal Use Only