Manual de serviço tv lg 32ln5650 chassis lb31j

Page 1

Internal Use Only North/Latin America Europe/Africa Asia/Oceania

http://aic.lgservice.com http://eic.lgservice.com http://biz.lgservice.com

LED TV SERVICE MANUAL CHASSIS : LB31J

MODEL : 32LN5650

32LN5650-TA

CAUTION

BEFORE SERVICING THE CHASSIS, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

P/NO : MFL67697801 (1303-REV00)

Printed in Korea


CONTENTS

CONTENTS . ............................................................................................. 2 SAFETY PRECAUTIONS ......................................................................... 3 SERVICING PRECAUTIONS ................................................................... 4 SPECIFICATION ....................................................................................... 6 ADJUSTMENT INSTRUCTION ................................................................ 8 BLOCK DIAGRAM ................................................................................. 14 EXPLODED VIEW .................................................................................. 15 SCHEMATIC CIRCUIT DIAGRAM ..............................................................

Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

-2-

LGE Internal Use Only


SAFETY PRECAUTIONS IMPORTANT SAFETY NOTICE Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Exploded View. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.

General Guidance

Leakage Current Hot Check (See below Figure) Plug the AC cord directly into the AC outlet.

An isolation Transformer should always be used during the servicing of a receiver whose chassis is not isolated from the AC power line. Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal injury from electrical shocks. It will also protect the receiver and it's components from being damaged by accidental shorts of the circuitry that may be inadvertently introduced during the service operation. If any fuse (or Fusible Resistor) in this TV receiver is blown, replace it with the specified. When replacing a high wattage resistor (Oxide Metal Film Resistor, over 1 W), keep the resistor 10 mm away from PCB. Keep wires away from high voltage or high temperature parts.

Do not use a line Isolation Transformer during this check. Connect 1.5 K / 10 watt resistor in parallel with a 0.15 uF capacitor between a known good earth ground (Water Pipe, Conduit, etc.) and the exposed metallic parts. Measure the AC voltage across the resistor using AC voltmeter with 1000 ohms/volt or more sensitivity. Reverse plug the AC cord into the AC outlet and repeat AC voltage measurements for each exposed metallic part. Any voltage measured must not exceed 0.75 volt RMS which is corresponds to 0.5 mA. In case any measurement is out of the limits specified, there is possibility of shock hazard and the set must be checked and repaired before it is returned to the customer.

Leakage Current Hot Check circuit

Before returning the receiver to the customer, always perform an AC leakage current check on the exposed metallic parts of the cabinet, such as antennas, terminals, etc., to be sure the set is safe to operate without damage of electrical shock.

Leakage Current Cold Check(Antenna Cold Check)

With the instrument AC plug removed from AC source, connect an electrical jumper across the two AC plug prongs. Place the AC switch in the on position, connect one lead of ohm-meter to the AC plug prongs tied together and touch other ohm-meter lead in turn to each exposed metallic parts such as antenna terminals, phone jacks, etc. If the exposed metallic part has a return path to the chassis, the measured resistance should be between 1 MΊ and 5.2 MΊ. When the exposed metal has no return path to the chassis the reading must be infinite. An other abnormality exists that must be corrected before the receiver is returned to the customer.

Copyright Š LG Electronics. Inc. All rights reserved. Only for training and service purposes

-3-

LGE Internal Use Only


SERVICING PRECAUTIONS CAUTION: Before servicing receivers covered by this service manual and its supplements and addenda, read and follow the SAFETY PRECAUTIONS on page 3 of this publication. NOTE: If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions on page 3 of this publication, always follow the safety precautions. Remember: Safety First. General Servicing Precautions 1. Always unplug the receiver AC power cord from the AC power source before; a. Removing or reinstalling any component, circuit board module or any other receiver assembly. b. Disconnecting or reconnecting any receiver electrical plug or other electrical connection. c. Connecting a test substitute in parallel with an electrolytic capacitor in the receiver. CAUTION: A wrong part substitution or incorrect polarity installation of electrolytic capacitors may result in an explosion hazard. 2. Test high voltage only by measuring it with an appropriate high voltage meter or other voltage measuring device (DVM, FETVOM, etc) equipped with a suitable high voltage probe. Do not test high voltage by "drawing an arc". 3. Do not spray chemicals on or near this receiver or any of its assemblies. 4. Unless specified otherwise in this service manual, clean electrical contacts only by applying the following mixture to the contacts with a pipe cleaner, cotton-tipped stick or comparable non-abrasive applicator; 10 % (by volume) Acetone and 90 % (by volume) isopropyl alcohol (90 % - 99 % strength) CAUTION: This is a flammable mixture. Unless specified otherwise in this service manual, lubrication of contacts in not required. 5. Do not defeat any plug/socket B+ voltage interlocks with which receivers covered by this service manual might be equipped. 6. Do not apply AC power to this instrument and/or any of its electrical assemblies unless all solid-state device heat sinks are correctly installed. 7. Always connect the test receiver ground lead to the receiver chassis ground before connecting the test receiver positive lead. Always remove the test receiver ground lead last. 8. Use with this receiver only the test fixtures specified in this service manual. CAUTION: Do not connect the test fixture ground strap to any heat sink in this receiver. Electrostatically Sensitive (ES) Devices Some semiconductor (solid-state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor “chip” components. The following techniques should be used to help reduce the incidence of component damage caused by static by static electricity. 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device, which should be removed to prevent potential shock reasons prior to applying power to the unit under test. Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly. 3. Use only a grounded-tip soldering iron to solder or unsolder ES devices. 4. Use only an anti-static type solder removal device. Some solder removal devices not classified as “anti-static” can generate electrical charges sufficient to damage ES devices. 5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices. 6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material). 7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. CAUTION: Be sure no power is applied to the chassis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES device.) General Soldering Guidelines 1. Use a grounded-tip, low-wattage soldering iron and appropriate tip size and shape that will maintain tip temperature within the range or 500 °F to 600 °F. 2. Use an appropriate gauge of RMA resin-core solder composed of 60 parts tin/40 parts lead. 3. Keep the soldering iron tip clean and well tinned. 4. Thoroughly clean the surfaces to be soldered. Use a mall wirebristle (0.5 inch, or 1.25 cm) brush with a metal handle. Do not use freon-propelled spray-on cleaners. 5. Use the following unsoldering technique a. Allow the soldering iron tip to reach normal temperature. (500 °F to 600 °F) b. Heat the component lead until the solder melts. c. Quickly draw the melted solder with an anti-static, suctiontype solder removal device or with solder braid. CAUTION: Work quickly to avoid overheating the circuit board printed foil. 6. Use the following soldering technique. a. Allow the soldering iron tip to reach a normal temperature (500 °F to 600 °F) b. First, hold the soldering iron tip and solder the strand against the component lead until the solder melts. c. Quickly move the soldering iron tip to the junction of the component lead and the printed circuit foil, and hold it there only until the solder flows onto and around both the component lead and the foil. CAUTION: Work quickly to avoid overheating the circuit board printed foil. d. Closely inspect the solder area and remove any excess or splashed solder with a small wire-bristle brush.

-4-

LGE Internal Use Only


IC Remove/Replacement Some chassis circuit boards have slotted holes (oblong) through which the IC leads are inserted and then bent flat against the circuit foil. When holes are the slotted type, the following technique should be used to remove and replace the IC. When working with boards using the familiar round hole, use the standard technique as outlined in paragraphs 5 and 6 above. Removal 1. Desolder and straighten each IC lead in one operation by gently prying up on the lead with the soldering iron tip as the solder melts. 2. Draw away the melted solder with an anti-static suction-type solder removal device (or with solder braid) before removing the IC. Replacement 1. Carefully insert the replacement IC in the circuit board. 2. Carefully bend each IC lead against the circuit foil pad and solder it. 3. Clean the soldered areas with a small wire-bristle brush. (It is not necessary to reapply acrylic coating to the areas). "Small-Signal" Discrete Transistor Removal/Replacement 1. Remove the defective transistor by clipping its leads as close as possible to the component body. 2. Bend into a "U" shape the end of each of three leads remaining on the circuit board. 3. Bend into a "U" shape the replacement transistor leads. 4. Connect the replacement transistor leads to the corresponding leads extending from the circuit board and crimp the "U" with long nose pliers to insure metal to metal contact then solder each connection. Power Output, Transistor Device Removal/Replacement 1. Heat and remove all solder from around the transistor leads. 2. Remove the heat sink mounting screw (if so equipped). 3. Carefully remove the transistor from the heat sink of the circuit board. 4. Insert new transistor in the circuit board. 5. Solder each transistor lead, and clip off excess lead. 6. Replace heat sink. Diode Removal/Replacement 1. Remove defective diode by clipping its leads as close as possible to diode body. 2. Bend the two remaining leads perpendicular y to the circuit board. 3. Observing diode polarity, wrap each lead of the new diode around the corresponding lead on the circuit board. 4. Securely crimp each connection and solder it. 5. Inspect (on the circuit board copper side) the solder joints of the two "original" leads. If they are not shiny, reheat them and if necessary, apply additional solder.

3. Solder the connections. CAUTION: Maintain original spacing between the replaced component and adjacent components and the circuit board to prevent excessive component temperatures. Circuit Board Foil Repair Excessive heat applied to the copper foil of any printed circuit board will weaken the adhesive that bonds the foil to the circuit board causing the foil to separate from or "lift-off" the board. The following guidelines and procedures should be followed whenever this condition is encountered. At IC Connections To repair a defective copper pattern at IC connections use the following procedure to install a jumper wire on the copper pattern side of the circuit board. (Use this technique only on IC connections). 1. Carefully remove the damaged copper pattern with a sharp knife. (Remove only as much copper as absolutely necessary). 2. carefully scratch away the solder resist and acrylic coating (if used) from the end of the remaining copper pattern. 3. Bend a small "U" in one end of a small gauge jumper wire and carefully crimp it around the IC pin. Solder the IC connection. 4. Route the jumper wire along the path of the out-away copper pattern and let it overlap the previously scraped end of the good copper pattern. Solder the overlapped area and clip off any excess jumper wire. At Other Connections Use the following technique to repair the defective copper pattern at connections other than IC Pins. This technique involves the installation of a jumper wire on the component side of the circuit board. 1. Remove the defective copper pattern with a sharp knife. Remove at least 1/4 inch of copper, to ensure that a hazardous condition will not exist if the jumper wire opens. 2. Trace along the copper pattern from both sides of the pattern break and locate the nearest component that is directly connected to the affected copper pattern. 3. Connect insulated 20-gauge jumper wire from the lead of the nearest component on one side of the pattern break to the lead of the nearest component on the other side. Carefully crimp and solder the connections. CAUTION: Be sure the insulated jumper wire is dressed so the it does not touch components or sharp edges.

Fuse and Conventional Resistor Removal/Replacement 1. Clip each fuse or resistor lead at top of the circuit board hollow stake. 2. Securely crimp the leads of replacement component around notch at stake top.

Copyright Š LG Electronics. Inc. All rights reserved. Only for training and service purposes

-5-

LGE Internal Use Only


SPECIFICATION

NOTE : Specifications and others are subject to change without notice for improvement.

1. Application range

This specification is applied to the LED TV used LB31J chassis.

3. Test method

2. Requirement for Test

1) Performance: LGE TV test method followed 2) Demanded other specification - Safety : CE, IEC specification - EMC : CE, IEC

Each part is tested as below without special appointment. 1) Temperature: 25 °C ± 5 °C(77 °F ± 9 °F), CST: 40 °C ± 5 °C 2) Relative Humidity: 65 % ± 10 % 3) Power Voltage : Standard input voltage (AC 100-240 V~, 50/60 Hz) * Standard Voltage of each products is marked by models. 4) Specification and performance of each parts are followed each drawing and specification by part number in accordance with BOM. 5) The receiver must be operated for about5 minutes prior to the adjustment.

4. Model General Specification No.

Item

Specification

Remarks

Market

Asia, Oceania, Africa, Middle East (PAL/DVB Market)

2.

Broadcasting system

1) PAL/SECAM-B/G/D/K 2) PAL-I 3) NTSC-M 4) DVB-T

3.

Channel Storage

ATV - 135EA, DTV - 1000EA

1.

Analog : Upper Heterodyne Digital : COFDM(DVB-T)

4.

Receiving system

5. 6.

Video(Composite Input) PAL, SECAM, NTSC Component Input Y/Cb/Cr, Y/Pb/Pr HDMI1-DTV/DVI HDMI Input HDMI2-DTV/DVI SPDIF out SPDIF out USB Input For My Media(Movie/Photo/Music List) and SVC Headphone

7. 8. 9 10

Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

-6-

► DVB-T - Guard Interval(Bitrate_Mbit/s) 1/4, 1/8, 1/16, 1/32 - Modulation : Code Rate QPSK : 1/2, 2/3, 3/4, 5/6, 7/8 16-QAM : 1/2, 2/3, 3/4, 5/6, 7/8 64-QAM : 1/2, 2/3, 3/4, 5/6, 7/8 4 System : PAL, SECAM, NTSC, PAL60

Only LB31B, LB31F chassis

LGE Internal Use Only


5. Component Video Input (Y, Cb/Pb, Cr/Pr) No.

Resolution

H-freq(kHz)

V-freq(Hz)

Porposed

1

720×480

15.73

60.00

SDTV, DVD 480i

2

720×480

15.63

59.94

SDTV, DVD 480i

3

720×480

31.47

59.94

480p

4

720×480

31.50

60.00

480p

5

720×576

15.625

50.00

SDTV, DVD 625 Line

6

720×576

31.25

50.00

HDTV 576p

7

1280×720

45.00

50.00

HDTV 720p

8

1280×720

44.96

59.94

HDTV 720p

9

1280×720

45.00

60.00

HDTV 720p

10

1920×1080

31.25

50.00

HDTV 1080i

11

1920×1080

33.75

60.00

HDTV 1080i

12

1920×1080

33.72

59.94

HDTV 1080i

13

1920×1080

56.250

50

HDTV 1080p

14

1920×1080

67.5

60

HDTV 1080p

6. HDMI Input : Refer to adjust specification about EDID data. 6.1. DTV mode No.

Resolution

H-freq(kHz)

V-freq.(kHz)

Pixel clock(MHz)

Proposed

1.

720*480

31.469 / 31.5

59.94 / 60

27.00/27.03

SDTV 480P

2.

720*576

31.25

50

54

SDTV 576P

3.

1280*720

37.500

50

74.25

HDTV 720P

4.

1280*720

44.96 / 45

59.94 / 60

74.17/74.25

HDTV 720P

5.

1920*1080

33.72 / 33.75

59.94 / 60

74.17/74.25

HDTV 1080I

6.

1920*1080

28.125

50.00

74.25

HDTV 1080I

7.

1920*1080

26.97 / 27

23.97 / 24

74.17/74.25

HDTV 1080P

8.

1920*1080

33.716/33.75

29.976/30.00

74.25

HDTV 1080P

9.

1920*1080

56.250

50

148.5

HDTV 1080P

10.

1920*1080

67.43 / 67.5

59.94 / 60

148.35/148.50

HDTV 1080P

6.2. PC mode No.

Resolution

H-freq(kHz)

V-freq.(Hz)

Pixel clock(MHz)

Proposed

1.

640*350 @70Hz

31.468

70.09

25.17

EGA

2.

720*400 @70Hz

31.469

70.08

28.321

DOS

3.

640*480 @60Hz

31.469

59.940

25.175

VESA(VGA)

4.

800*600 @60Hz

37.879

60.31

40.000

VESA(SVGA)

5.

1024*768 @60Hz

48.363

60.00

65.000

VESA(XGA)

6

1152*864 @60Hz

54.348

60.053

80.002

VESA

7.

1280*1024 @60Hz

63.981

60.020

108

VESA(SXGA)

8.

1360*768 @60Hz

47.712

60.015

85.5

VESA(WXGA)

9.

1920*1080 @60Hz

67.5

60.0

148.5

WUXGA (Reduced blanking)

Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

-7-

Remark

FHD only(Support to HDMI-PC)

FHD only(Support to HDMI-PC)

LGE Internal Use Only


ADJUSTMENT INSTRUCTION 1. Application Range

(4) Click "Connect" tab. If "Can't" is displayed, check connection between computer, jig, and set.

This specification sheet is applied to all of the LED TV with LB31J chassis.

(2)

(3)

2. Designation

(1) T he adjustment is according to the order which is designated and which must be followed, according to the plan which can be changed only on agreeing. (2) Power adjustment : Free Voltage. (3) Magnetic Field Condition: Nil. (4) Input signal Unit: Product Specification Standard. (5) Reserve after operation: Above 5 Minutes (Heat Run) Temperature : at 25 °C ± 5 °C Relative humidity : 65 ± 10 % Input voltage : 100-220 V~, 60 Hz (6) Adjustment equipments : Color Analyzer(CA-210 or CA-110), Service remote control. (7) Push the “IN STOP" key - For memory initialization.

Please Check the Speed : To use speed between from 200KHz to 400KHz

(5) Click "Auto" tab and set as below. (6) Click "Run". (7) After downloading, check "OK" message.

Case1 : Software version up 1. After downloading S/W by USB , TV set will reboot automatically. 2. Push “In-stop” key. 3. Push “Power on” key. 4. Function inspection 5. After function inspection, Push “In-stop” key. Case2 : Function check at the assembly line 1. When TV set is entering on the assembly line, Push “In-stop” key at first. 2. Push “Power on” key for turning it on. → If you push “Power on” key, TV set will recover channel information by itself. 3. After function inspection, Push “In-stop” key.

(4) filexxx.bin

(5)

(7)...........OK

(6)

* USB DOWNLOAD(*.epk file download)

(1) Put the USB Stick to the USB socket. (2) Automatically detecting update file in USB Stick. - If version of update file in USB Stick is lower, it will not work. But version of update file is higher, USB data will be detected automatically.

3. Main PCB check process ▪ APC - After Manual-Insert, executing APC

* Boot file Download

(1) Execute ISP program "Mstar ISP Utility" and then click "Config" tab. (2) Set as below, and then click "Auto Detect" and check "OK" message. If "Error" is displayed, check connection between computer, jig, and set. (3) Click "Read" tab, and then load download file(XXXX.bin) by clicking "Read" (1) filexxx.bin

Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

-8-

LGE Internal Use Only


4. ADC Process

(3) Show the message "Copying files from memory".

4.1. ADC

- Enter Service Mode by pushing "ADJ" key, - Enter Internal ADC mode by pushing "►" key at "8. ADC Calibration". ADC Calibration

EZ ADJUST 0. Tool Option1

NG

ADC Comp 480i

1. Tool Option2 2. Tool Option3 3. Tool Option4

ADC Comp 1080p

NG

ADC Type

OPT

4. Tool Option5

Start

5. Tool Option Commercial

Reset

6. Country Group 7. Area Option 8. ADC Calibration

(4) Updating is starting.

9. White Balance 10. 10 Point WB 11. Test Pattern 12. EDID D/L 13. Sub B/C 14. Ext. Input Adjust

<Caution> U sing "P-ONLY" key of the Adjustment remote control, power on TV. * ADC Calibration Protocol (RS232)

(5) Updating Completed, The TV will restart automatically. (6) If your TV is turned on, check your updated version and Tool option. (explain the Tool option, next stage) * If updated version is higher than what TV has, the TV can lost all channel data. In this case, you have to channel recover. If all channel data is cleared, you didn’t have a DTV/ATV test on production line.

NO

* RS-232C Connection Method.

CMD 2

Adjust ‘Mode In’

Item

Data 0

A

A

0

0

When transfer the ‘Mode In’, Carry the command.

ADC adjust

ADC Adjust

A

D

1

0

Automatically adjustment (The use of a internal pattern)

Adjust Sequence ▪ aa 00 00 [Enter Adjust Mode] ▪ xb 00 40 [Component1 Input (480i)] ▪ ad 00 10 [Adjust 480i Comp1] ▪ aa 00 90 End Adjust mode * Required equipment : Adjustment remote control.

* After downloading, have to adjust Tool Option again. (1) Push "IN-START" key in service remote control. (2) Select "Tool Option 1" and push "OK" key. (3) Punch in the number. (Each model has their number) (4) Completed selecting Tool option.

CMD 1

Enter Adjust MODE

4.2. Function Check

Connection : PCBA (USB Port) → USB to Serial Adapter (UC-232A) → RS-232C cable → PC(RS-232C port) ● Product name of USB to Serial Adapter is UC-232A.

4.2.1. Check display and sound

■ Check Input and Signal items. (1) TV (2) AV (CVBS) (3) COMPONENT (480i) (4) HDMI * Display and Sound check is executed by Remote control. <Caution> Not to push the "INSTOP" key after completion if the function inspection.

Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

-9-

LGE Internal Use Only


5. Total Assembly line process

* Connecting picture of the measuring instrument (On Automatic control) Inside Pattern is used when W/B is controlled. Connect to auto controller or push Adjustment Remote control POWER ON → Enter the mode of White-Balance, the pattern will come out.

5.1. Adjustment Preparation

▪ W/B Equipment condition CA210: CH14, Test signal: Inner pattern(80IRE)-LED Module ▪ Above 5 minutes H/run in the inner pattern. ("power on" key of Adjustment remote control) * The spec of color temperature and coordinate. Mode

Color Temp

Cool (C50)

13,000 K

Medium(0)

9,300 K

Warm(W50)

6,500 K

Color coordinate X=0.271 (±0.002) Y=0.270 (±0.002) X=0.285 (±0.002) Y=0.293 (±0.002) X=0.313 (±0.002) Y=0.329 (±0.002)

Full White Pattern

Remark <Test Signal> - Inner pattern for W/B adjust - External white pattern (80IRE, 204gray)

COLOR ANALYZER TYPE : CA-210

RS-232C Communication

▪ W/B Table in process of aging time - LGD / CMI Module

* Auto-control interface and directions

Aging time color coordinate Target 1 0-2 2 3-5 3 6-9 4 10-19 5 20-35 6 36-49 7 50-79 8 80-119 9 Over 120

Normal Line Cool Medium x y x y 271 270 285 293 281 287 295 310 280 285 294 308 278 284 292 307 276 281 290 304 275 277 289 300 274 274 288 297 273 272 287 295 272 271 286 294 271 270 285 293

x 313 320 319 317 315 314 313 312 311 310

Aging time color coordinate Target 1 0-5 2 6-10 3 11-20 4 21-30 5 31-40 6 41-50 7 51-80 8 81-119 9 Over 120

aging chamber Cool Medium x y x y 271 270 285 293 280 285 294 308 276 280 290 303 272 275 286 298 269 272 283 295 267 268 281 291 266 265 280 288 265 263 279 286 264 261 278 284 264 260 278 283

Warm x y 313 329 319 340 315 335 311 330 308 327 306 323 305 320 304 318 303 316 303 315

(1) Adjust in the place where the influx of light like floodlight around is blocked. (Illumination is less than 10 lux). (2) Adhere closely the Color analyzer(CA210) to the module less than 10 cm distance, keep it with the surface of the Module and Color analyzer's prove vertically.(80° ~ 100°). (3) Aging time - After aging start, keep the power on (no suspension of power supply) and heat-run over 5 minutes. - Using 'no signal' or 'POWER ONLY' or the others, check the back light on.

Warm y 329 342 340 339 336 332 329 327 326 325

▪ Auto adjustment Map(RS-232C) RS-232C COMMAND [CMD ID DATA] Wb 00 00 White Balance Start Wb 00 ff White Balance End RS-232C COMMAND [CMD ID DATA] Cool

Mid

R Gain

jg

Ja

jd

G Gain

jh

Jb

je

B Gain

ji

Jc

jf

cool spec target

med y 270 289

x 285 299

y 293 317

Warm

00

172

192

192

192

00

172

192

192

192

00

192

192

172

192

R Cut

64

64

64

128

G Cut

64

64

64

128

B Cut

64

64

64

128

- 10 -

Warm

MAX

Mid

Warm x y 313 329 335 340

Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

CENTER (DEFAULT)

MIN

Cool

- AUO/ COST/ SHARP/ BOE Module which cool spec is 13000K x 271 276

CA-210

<Caution> Color Temperature : COOL, Medium, Warm. One of R Gain/G Gain/ B Gain should be kept on 0xC0, and adjust other two lower than C0.(When R/G/B Gain are all C0, it is the FULL Dynamic Range of Module)

LGE Internal Use Only


* Manual W/B process using adjust Remote control.

* CASE Cool First adjust the coordinate far away from the target value(x, y). 1) x, y > target i) Decrease the R, G. 2) x, y < target i) First decrease the B gain, ii) Decrease the one of the others. 3) x > target, y < target i) First decrease B, so make y a little more than the target. ii) Adjust x value by decreasing the R. 4) x < target, y > target i) First decrease B, so make x a little more than the target. ii) Adjust x value by decreasing the G. * After You finish all adjustments, Press “In-start” button and compare Tool option and Area option value with its BOM, if it is correctly same then unplug the AC cable. If it is not same, then correct it same with BOM and unplug AC cable. For correct it to the model’s module from factory JIG model. * Push the “IN STOP" key after completing the function inspection.

■ Color analyzer(CA100+, CA210) should be used in the calibrated ch by CS-1000. ■ Operate the zero-calibration of the CA100+ or CA-210, then stick sensor to the module when adjusting. ■ After enter Service Mode by pushing “ADJ” key, ■ Enter White Balance by pushing “►” key at “9. White Balance”. EZ ADJUST 0. Tool Option1

Whit Balance

1. Tool Option2

◄ Cool

2. Tool Option3

Color Temp.

3. Tool Option4

R-Gain

172

4. Tool Option5

G-Gain

192

5. Tool Option Commercial

B-Gain

192

6. Country Group

R-Cut

64

7. Area Option

G-Cut

8. ADC Calibration

B-Cut

64

9. White Balance

Test-Pattern

ON

10. 10 Point WB

Backlight

100

11. Test Pattern

Reset

64

To Set

12 EDID D/L 13. Sub B/C 14. Ext. Input Adjust

■ For manual adjustment, it is also possible by the following sequence. (1) Set TV in Adj. mode using “P-ONLY” key on remote controller and then operate heat run longer than 15 minutes.(If not executed this step, the condition for W/B may be different.) (2) Push “Exit” key. (3) Enter White Balance mode by pushing the ADJ key and select “9. White Balance”. When KEY (►) is pressed, 206 Gray internal pattern will be displayed. (4) Zero Calibrate the probe of Color Analyzer, then place it on the center of LCD module within 10 cm of the surface (5) S elect each items (Red/Green/Blue Gain) using ▲/▼(CH +/-) key on Remote control. (6) Adjust R/ G/ B Gain using ◄/►(VOL +/-) key on R/C. (7) Adjust three modes all (Cool / Medium / Warm) - For All model w/o LS345 Fix the one of R/G/B gain and change the others - For G-FIX model Cool Mode 1) Fix the one of R/G/B gain to 192 (default data) and decrease the others. (If G gain is adjusted over 172 and R and B gain less than 192 , Adjust is O.K.) 2) If G gain is less than 172, Increase G gain by up to 172, and then increase R gain and G gain same amount of increasing G gain. 3) If R gain or B gain is over 255, readjust G gain less than 172, Conform to R gain is 255 or B gain is 255 Medium / Warm Mode - Fix the one of R/G/B gain to 192 (default data) and decrease the others. (8) When adjustment is completed, exit adjustment mode using EXIT key on Remote control.

5.2. DDC EDID Write (HDMI 256Byte)

■ Connect HDMI Signal Cable to HDMI Jack. ■ Write EDID DATA to EEPROM(24C02) by using DDC2B protocol. ■ Check whether written EDID data is correct or not. * For SVC main Assembly, EDID have to be downloaded to Insert Process in advance.

5.3. EDID DATA

1) All Data : HEXA Value 2) Changeable Data : *: Serial No : Controlled / Data:01 **: Month : Controlled / Data:00 ***: Year : Controlled ****: Check sum

- Auto Download

■ After enter Service Mode by pushing “ADJ” key, ■ Enter EDID D/L mode. ■ Enter “START” by pushing “OK” key. EDID D/L

EZ ADJUST 0. Tool Option1

HDMI1

1. Tool Option2

HDMI2

2. Tool Option3

NG NG

Start

3. Tool Option4

Reset

4. Tool Option5 5. Tool Option Commercial

EDID D/L

6. Country Group

HDMI1

7. Area Option

HDMI2

8. ADC Calibration 9. White Balance

Start

OK OK Reset

10. 10 Point WB 11. Test Pattern 12. EDID D/L

13. Sub B/C 14. Ext. Input Adjust

Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

- 11 -

LGE Internal Use Only


5.4. Outgoing condition Configuration

[Caution] * Use the proper signal cable for EDID Download - Analog EDID : Pin3 exists - Digital EDID : Pin3 exists

■ When pressing IN-STOP key by Service remote control, Red LED are blinked alternatively. And then automatically turn off. (Must not AC power OFF during blinking)

* Edid data and Model option download (RS232) NO

Item

CMD 1 CMD 2

Enter download Download Mode ‘Mode In’ EDID data and Model option ADC Adjust download

A

A

A

00

When transfer the ‘Mode In’, Carry the command.

10

Automatically adjustment (The use of a internal pattern)

No.

Item

Condition

Hex Data

1

Manufacturer ID

GSM

1E6D

2

Version

Digital : 1

01

3

Revision

Digital : 3

03

(1) 2D HD HDMI EDID DATA 0 10 20 30 40 50 60 70 80 90 A0 B0 C0 D0 E0 F0

0 0

0F 01 36 18 3E 02 22 80 00 20 96 58 00

c

1 ff

50 01 00 88 1E

2 ff 01 54 01 40 03 53

3 ff 03 A1 01 84 06 10

4 ff 80 08 01 63 40 00

5 ff A0 00 01 00 84 0A

6 ff 5A 31 66 00 63 20

03 15 1E 00 C2 00 2C 00

22 01 01 00 31 A0 45 00

F1 26 1D 9E 00 5A 00 00

4E 15 80 01 00 00 A0 00

10 07 18 1d 1E 00 5A 00

1F 50 71 00 8C 00 00 00

d

7 00 78 40 21 1E 00 20

8 1E 0A 45 50 64 00 20

9 6D EE 40 B0 19 18 20

04 09 1C 72 0A 18 00 00

93 57 16 51 D0 02 00 00

05 07 20 D0 8A 3A 1E 00

(2) Detail EDID Options are below a. Product ID Model Name HEX EDID Table HD/FHD Model

0001

01 00

5.5.1. GND & HI-POT auto-check preparation

0

0

E

5.5. GND and HI-POT Test

Data 0

A 91 61 51 00 00 20

a

58 1E 20 80 00 00

5.5.2. GND & HI-POT auto-check

B

C

D

A3 40 00 40 00 20

54 71 1B 40 00

4C 40 30 00 FD

14 03 2C 20 E0 18 00 00

- Check the POWER CABLE and SIGNAL CABE insertion condition.

b

d

E

F

99 01 40 26 00

26 01 70 30 3A

(1) Pallet moves in the station.(POWER CORD / AV CORD is tightly inserted) (2) Connect the AV JACK Tester. (3) Controller (GWS103-4) on. (4) GND Test (Auto) - If Test is failed, Buzzer operates. - If Test is passed, execute next process(Hi-pot test). (Remove A/V CORD from A/V JACK BOX) (5) HI-POT test (Auto) - If Test is failed, Buzzer operates. - If Test is passed, GOOD Lamp on and move to next process automatically.

5.5.3. Checkpoint

01 e 02 12 20 21 f 25 00 A0 5A 6E 28 55 00 2D 10 10 3E 71 38 2D 40 00 00 00 00 00 00 00 e

(1) Test voltage 1) 3 Poles - GND: 1.5KV/min at 100 mA - SIGNAL: 3KV/min at 100 mA 2) 2 Poles - SIGNAL: 3 KV/min at 100 mA (2) TEST time: 1 second (3) TEST POINT 1) 3 Poles - GND Test = POWER CORD GND and SIGNAL CABLE GND. - Hi-pot Test = POWER CORD GND and LIVE & NEUTRAL. 2) 2 Poles - Hi-pot Test = Accessible Metal and LIVE & NEUTRAL. (4) LEAKAGE CURRENT: At 0.5mArms

DDC Function Analog/Digital

b. Serial No: Controlled on production line. c. Month, Year: Controlled on production line: ex) Week : '01' -> '01' Year : '2012' -> '16' fix d. Model Name(Hex): cf) TV set’s model name in EDID data is below.

6. Local Dimming Function Check

MODEL NAME

MODEL NAME(HEX)

LG TV

00 00 00 FC 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 (LG TV)

e. Checksum: Changeable by total EDID data. EDID C/S data Check Sum (Hex)

Block 0 Block 1

HD(Non DTS) HDMI A3 52 (HDMI1) 42 (HDMI2)

HD(DTS) HDMI A3 52 (HDMI1) 42 (HDMI2)

Step1) Turn on TV. Step2) Press “P-only” key, enter to power only mode and escape the “P-only” Mode by pressing “Exit” key. Step3) Press “Tilt” key, entrance to Local Dimming mode. Step4) At the Local Dimming mode, module Edge Backlight moving Top to bottom Back light of module moving. Step5) confirm the Local Dimming mode. Step6) Press “Exit” key.

f. Vendor Specific Input HDMI1 HDMI2

Model name(HEX) 67030C001000 67030C002000

Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

- 12 -

LGE Internal Use Only


7. 3D function test

(Pattern Generator MSHG-600, MSPG-6100[Support HDMI1.4]) * HDMI mode No. 872 , pattern No.83 (1) Please input 3D test pattern like below.

(2) When 3D OSD appear automatically, then select OK button.

(3) Don't wear a 3D Glasses, check the picture like below.

8. EYE-Q function check

Step1) Turn on TV Step 2) Press EYE key of Adj. R/C. Step 3) Cover the Eye Q sensor on the front of the using your hand and wait for 6 seconds. Step 4) Confirm that R/G/B value is lower than 10 of the “Raw Data(Sensor data, Back light)”. If after 6 seconds, R/ G/ B value is not lower than 10, replace Eye Q sensor Step 5) Remove your hand from the Eye Q sensor and wait for 6 seconds. Step 6) Confirm that “ok” pop up. If change is not seen, replace Eye Q sensor.

Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

- 13 -

LGE Internal Use Only


USB (JK1500)

Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

- 14 -

AV (JK1701)

AV Component (JK1701)

REAR

System EEPROM (256Kbit)

IC104

Serial Flash (8Mbit)

IC1300

Tuner (TU3702)

HDMI1 (JK801)

HDMI_SIDE (MHL) (JK803)

SIDE

USB (JK700)

DDC_SCL/SDA_2

CK+/-, D0+/-, D1+/-, D2+/-_HDMI2

MHL_CD_SENSE

DDC_SCL/SDA_4

CK+/-, D0+/-, D1+/-, D2+/-_HDMI4

DCDC + OCP IC (IC401)

USB1_OCD/CTL

I2C_SCL/SDA

SPI_SCK/SDI/SDO/CS

TU_SCL / SDA

IF_P/N_MSTAR, TU_CVBS, TU_SIF

AV2_CVBS_IN

AV2_R/L_IN

COMP2_Y+, AV_CVBS_IN

COMP2_R/L_IN, COMP2_Pr+/Pb+, AV_CVBS_DET

+5V_USB

SIDE_USB1_DM/DP

S7LR_M1 (LGE2121-MS)

IC102

OCP IC

IC802

P600

Woofer_R

Woofer_L

SPK_R

(P1101)

30P HD LVDS wafer

8P connector

STA380 (IC3404)

STA380 (IC3403)

STA380 (IC3402)

SPK_L

DDR3 SDRAM (2Gbit)

IC1201

NAND FLASH (1Gbit)

STA380 (IC3401)

RXA0+/-~RXA4+/-, RXACK+/RXB0+/-~RXB4+/-, RXBCK+/-

, KEY1/2, LED_R/BUZZ, IR

AMP_SCL/SDA

AUD_MASTER_CLK, AUD_LRCH, AUD_LRCK, AUD_SCK

AMP_SCL/SDA

AUD_MASTER_CLK, AUD_LRCH, AUD_LRCK, AUD_SCK

AMP_SCL/SDA

(IC101)

AUD_MASTER_CLK, AUD_LRCH, AUD_LRCK, AUD_SCK

Main SOC

AMP_SCL/SDA

AUD_MASTER_CLK, AUD_LRCH, AUD_LRCK, AUD_SCK

A-MDQL[0-7], A-MDQU[0-7],… B-MDQL[0-7], B-MDQU[0-7],…

PCM_A[0-7],…

MHL_CD_SENSE, AVDD5V_MHL, VBUS_EN

BLOCK DIAGRAM

LGE Internal Use Only


EXPLODED VIEW IMPORTANT SAFETY NOTICE

A10

Set + Stand

A9

Stand Base + Stand Body

301

A2

300

501

500

200

900

910

510

122

530

LV1

125

123

125

120

540

521

400

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and EXPLODED VIEW. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.

Copyright Š LG Electronics. Inc. All rights reserved. Only for training and service purposes

- 15 -

LGE Internal Use Only


TP for NON-EU models(except EU and China) TP for CI slot /PCM_REG

PCM_D[0]

TP for SCART PCM_A[8]

CI_TS_CLK

SCART1_MUTE

TP for Headphone HP_LOUT

/PCM_OE

PCM_D[1]

PCM_A[9]

CI_TS_VAL

SC1_ID

HP_ROUT

/PCM_WE

PCM_D[2]

PCM_A[10]

CI_TS_SYNC

SC1_FB

SIDE_HP_MUTE

/PCM_IORD

PCM_D[3]

PCM_A[11]

CI_TS_DATA[0]

SC1_SOG_IN

HP_DET

/PCM_IOWR

PCM_D[4]

PCM_A[12]

CI_TS_DATA[1]

DTV/MNT_VOUT

/PCM_CE

PCM_D[5]

PCM_A[13]

CI_TS_DATA[2]

SCART1_Lout

/PCM_IRQA

PCM_D[6]

PCM_A[14]

CI_TS_DATA[3]

SCART1_Rout

/PCM_CD

PCM_D[7]

CI_TS_DATA[4]

SC1_CVBS_IN

/PCM_WAIT

CI_TS_DATA[5]

SC1_R+/COMP1_Pr+

PCM_RST

CI_TS_DATA[6]

SC1_G+/COMP1_Y+

PCM_5V_CTL

CI_TS_DATA[7]

SC1_B+/COMP1_Pb+

CI_DET

SC1/COMP1_DET

SC1/COMP1_L_IN

SC1/COMP1_R_IN

TP for FE_TS_DATA

TP for S2 S2_RESET

FE_TS_DATA[1]

FE_TS_DATA[2]

FE_TS_DATA[3]

FE_TS_DATA[4]

FE_TS_DATA[5]

FE_TS_DATA[6]

FE_TS_DATA[7]

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

NC4_S7LRM TP_NON_EN

2012.07.02 3

LGE Internal Use Only


L13 POWER BLOCK (POWER DETECT 2) PANEL_POWER

FROM LIPS & POWER B/D

+3.5V_ST --> 3.375V --> 3.46V +24V --> 3.78V --> 3.92V (3.79V) +12V --> 3.58V --> 3.82V (3.68V)

Power_DET

R402-*1 100

+12V BEAD_CSG L412-*1 UBW2012-121F

+3.5V_SOC_RESET +12V

BEAD_SAMSUNG L412 120 CIS21J121

Q402

+3.3V_Normal

+3.5V_ST 3

R461 10K

2

R415 100

R426 10K

R401 10K

E

E

POWER_DET_RESET

Q405 MMBT3904(NXP)

C406

0.1uF

1

2

DRV ON

3.5V

3

4

PDIM#1

3.5V

CIC21J501NE

16V

PWR ON

L407

+24V C418

0.1uF

MLB-201209-0120P-N2

50V

L405 MLB-201209-0120P-N2

BEAD_SAMSUNG CIC21J501NE L421

6

PDIM#2

GND

7

8

GND

24V

9

10

24V

5

R408

100

+3.5V_ST

11

12

13

14

12V

L420

12V

15

16

N.C

BLM18PG121SN1D

GND

17

18

GND

[EP]

IN

1

8

19 .

PG

VCC BEAD_SAMWHA L402-*1 CB2012PK501T

BEAD_SAMWHA L410-*1 CB2012PK501T

IC407 AP7173-SPG-13 HF(DIODES)

2

16V BEAD_SAMWHA L421-*1 CB2012PK501T

VCC

3

PD_+24V R403 1.5K 1%

2

GND PD_+24V R480 100

RESET

PWR_DET_ON_DIODES IC409-*1 APX803D29

1 GND RESET

2

3

VCC

1 GND

PWM1

PWM2_2CH_POWER

12V

CIC21J501NE

3 1

PD_+24V_PWR_DET_DIODES

GND

BEAD_SAMSUNG L402

0.1uF

2

PWM_DIM

GND

+12V C404

PWM_DIM_PULL_DOWN *For 55LN54 Power ON Noise

+1.5V_DDR

RESET

PD_+24V_PWR_DET_ON_SEMI IC409 NCP803SN293

3

1.5A6

4

5

+3.3V_Normal R433 10K

EN

7

+1.5V_DDR

L410 CIC21J501NE BEAD_SAMSUNG

OUT

+3.3V_Normal

R1 R457

FB

4.3K 1/16W 1%

SS

C472 22uF 10V

R2 C467 560pF 50V

GND

R456 4.7K 1/16W 1%

C476 0.1uF 16V

+3.5V_ST

D403 5V OPT

+3.3V_Normal

FET_2.5V_AOS AO3435 Q403 S

BEAD_SAMSUNG L404

3.9K

9

BEAD_SAMSUNG CIC21J501NE L408

+3.5V_ST

R412

PD_+24V C412 0.1uF 16V

THERMAL

BEAD_SAMWHA L404-*1 CB2012PK501T

IC408-*1

PD_+24V R404 100K

+24V

+3.5V_POWER

P401 SMAW200-H18S1

POWER_DET

C474 0.1uF

GND

PD_+24V R482 8.2K 1%

MLB-201209-0120P-N2 L409

3.5V_DIODE D401 5V

RESET

1

VCC

BEAD_SAMWHA L408-*1 CB2012PK501T

2

RESET_IC_SOC_RESET

RESET_IC_SOC_RESET R402 300

APX803D29

E

INV_CTL

3

PD_+12V R447 1.2K 1%

R407 5.6K

R489 10K

Q401 MMBT3904(NXP)

R462 10K

R405 5.6K

Q407 MMBT3904(NXP)

B

001:AL22

R421 10K

B

C B

C411 0.1uF 16V

C

R430 10K

PANEL_CTL C

RL_ON

R440 5.6K

R419 1K

OPT R411 33K

PWR_DET_ON_SEMI IC408 NCP803SN293

5%

VCC

+3.5V_ST

R406 4.7K

OPT

R463 10K

PD_+3.5V R450 0

C461 10uF 10V R434 10K

C423 2.2uF 10V

R438 22K

L403 BLM18PG121SN1D

D

R416 10K

PD_+12V R448 2.7K 1%

PANEL_VCC G

C437 22uF 10V

C425 0.1uF 16V

G

1

C443 10uF 16V

R439 33K

C438 0.1uF 25V OPT

MMBT3906(NXP)

+3.5V_ST R488 100K

D

S +3.5V_ST

+3.5V_ST

Q409 AO3407A

D405 5V

R445

Vout=0.8*(1+R1/R2)=1.5319

2.2K

G

E

+2.5V_Normal IC402 +3.3V_Normal

2

OUT

S7LR core 1.15V volt

GND

+5V_Normal

C403 10uF 10V 85C

CAP_10uF_X5R

R1

C422 0.1uF 16V OPT

+3.5V_ST

BEAD_SAMSUNG L413 CIC21J501NE

SW_IN 9

+5V_USB C430 10uF 10V

8 SW_OUT

+5V_Normal +3.3V_Normal

VIN_1

1

VIN_2

2

GND_1

3

C453 22uF 10V

SS/TR

C444 0.1uF 16V

C456 22uF 10V

RT/CLK

+3.3V_TU

D404 5V OPT

C488

8

6

7 COMP

+3.5V_ST -> 3.3V_TU

R432 1/16W 330K 5% R436 15K

R1

C448 3300pF

R442 30K 1/16W 1%

C439 50V 100pF

V0 = 0.8*(1+(R1/R2)) IC410 MP20051

[EP]GND

IN_2

C489 10uF 6.3V

NC

8

7

1 THERMAL

IN_1

9

R413 16K

10uF 10V CAP_10uF_X7R

CIS21J121 L3703

4

50V +3.5V_POWER

C417-*1

C410 3300pF 50V

2

6

3

C490 0.1uF 16V

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

EN

5

4

R2

3A

OUT_2

R495 1

FB

GND

R441 75K 1/16W 1%

Vout=0.827*(1+R1/R2)

OUT_1

C3723 22uF 6.3V

C3725 0.1uF 16V

R1 1%

R492 10K POWER_ON/OFF_1

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

PH_1

5 USB1_CTL

RLIM

2

3 ROSC

COMP

1 SS

C426 100pF 50V OPT

PH_2

L415 3.6uH

3300pF USB1_OCD

EN_SW

R409 2K

4

11

IC403 10 TPS54319TRE 9

THERMAL 17

AGND

R417 4.7K OPT

FAULT

EN [EP]

R414 10K

5

16

V7V

AGND 6

IC401 TPS65281RGV

VIN 15

C419 4.7uF 10V

PH_3

7

14

GND_2

12

VSENSE

10

11

LX

BST 12 PGND

THERMAL 17

C405 10uF 16V

C417 CAP_10uF_X5R 10uF CHANGE TO 10V 10UF/10V/X5R 85C

13

L401 CIC21J501NE BEAD_SAMSAUNG

FB

11K 1% CHANGE TO 16V/X5R

+1.10V_VDDC

C441 0.1uF 16V

C403-*1 10uF 10V CAP_10uF_X7R

BOOT

R2

PWRGD

R454

13

C424 330pF 50V

0.33uF 16V

R428 10K

EN

R453 27K 1%

C447

+3.3V_Normal

CHANGE TO 10UF/10V/X5R

14

R452 33K 1%

15

C421 22uF 16V OPT

BEAD_SAMWHA L413-*1 CB2012PK501T

EP[GND]

C420 22uF 16V

D402 5V OPT

VIN_3

L406 3.6uH C413 0.047uF 25V

C440 0.1uF 16V

16

Vout=0.8*(1+R1/R2)

+12V

R410 100K

3 1

R491 0

BEAD_SAMWHA L401-*1 CB2012PK501T

+2.5V_Normal

TJ1118S-2.5 IN

+5V_Normal & +5V_USB

D

Q400 MMBT3904(NXP)

B

S

R443 10K

POWER_ON/OFF_1

FET_2.5V_DIODE DMP2130L Q403-*1

C

R2 1%

R493 1.5K

R494 4.7K

C491 10uF 6.3V

CHANGE TO 6.3V 2012 X5R

NC4_S7LRM Power_PD2

2012/09/19 4

LGE Internal Use Only


USB (SIDE)

+5V_USB

C700 22uF 10V

3

1 2

SIDE_USB1_DM

SIDE_USB1_DP

5

4

USB DOWN STREAM

3AU04S-305-ZC-(LG)

JK700

D700 RCLAMP0502BA OPT

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

NC4_S7LRM USB

12/06/20 7

LGE Internal Use Only


HDMI (REAR 1 / SIDE 1 MHL) HDMI_1

SIDE_HDMI (MHL) 5V_HDMI_4

GND HDMI-2 BODY_SHIELD

5V_DET_HDMI_2 R807

20 19

HP_DET

C

19

R803

R832

100

R833

100

R805

0

HDMI_ARC

14

HDMI1_ARC

HDMI_CEC

EAG59023302

13

1

D826 RCLAMP0524PA 10

CK-_HDMI2

2

9

CK+_HDMI2

3

8

4

7

D0-_HDMI2

5

6

D0+_HDMI2

12 11 10

CK+ D0-

9

D0_GND

8

4 3

DDC_CLK

14

NC

D1-_HDMI2

D1+

2

9

D1+_HDMI2

D2-

3

8

4

7

D2-_HDMI2

5

6

D2+_HDMI2

VA806 ESD_HDMI

VA807 ESD_HDMI

CE_REMOTE CK-

11

CK_GND

D828 RCLAMP0524PA 1 10

CK+

2

9

D0-

3

8

4

7

5

6

8

6

3 2 1

DDC_SDA_4

R835

100 HDMI-2

DDC_SCL_4

HDMI_CEC

D0_GND D0+

CK-_HDMI4 CK+_HDMI4 D0-_HDMI4 D0+_HDMI4

ESD_HDMI_SEMTECH

D1D1_GND

1

D829 RCLAMP0524PA 10

D1+

2

9

3

8

D2-

4

7

D2_GND

5

6

D1-_HDMI4 D1+_HDMI4 D2-_HDMI4 D2+_HDMI4

ESD_HDMI_SEMTECH

D2+

OPT D811

JK803

VA801-*1 1uF 10V ESD_HDMI1_CAP

JK801

100 HDMI-2

+3.5V_ST

ESD_HDMI_SEMTECH D801 ESD_HDMI1_VARISTOR

R834

VA808 ESD_HDMI

13

7

D827 RCLAMP0524PA 10

VA805 ESD_HDMI

HPD4

12

9

1

D2+

1

15

4

D2_GND

2

DDC_DATA

ESD_HDMI_SEMTECH

D1_GND

5

16

10

D1-

6

1.8K

5

D0+

7

GND

DDC_SDA_2

VA803 ESD_HDMI

15

17

DDC_SCL_2

VA804 ESD_HDMI

ESD_HDMI1_VARISTOR

16

HPD2

VA802 ESD_HDMI

3.3K

1.8K VA801

17

R817 10K

E R801

18

B

Q801 MMBT3904(NXP)

5V

100

HDMI-2

R810 0

D801-*1 1uF 10V ESD_HDMI1_CAP

D812 5.6V

C801 0.047uF 25V HDMI-2

E

R812 10K

HDMI-2 OPT

1K

EAG62611204

20

18

R819

OPT R811 10K

R826

R830

HDMI-2

3.3K

10K SHIELD

HDMI-2 R818

5V_HDMI_2

5V_DET_HDMI_4

OPT

C

Q803 OPT

B C

B Q802 OPT

MHL_CD_SENSE

E

GND_1

TMDS_CH2-

R820 100

TMDS_CH2+

HDMI_CEC

CEC_REMOTE_S7

1

10

2

9

3

8

4

7

5

6

NC_4

TMDS_CH1-

NC_3

TMDS_CH1+

GND_2

GND_1

NC_2

TMDS_CH2-

NC_1

TMDS_CH2+

1

10

2

9

3

8

4

7

5

6

NC_4

NC_3

GND_2

NC_2

NC_1

ESD_HDMI_NXP

ESD_HDMI_NXP

D828-*1 IP4283CZ10-TBA

D829-*1 IP4283CZ10-TBA

MHL OCP AVDD5V_MHL

TMDS_CH1-

TMDS_CH1+

GND_1

5V_HDMI_2

5V_HDMI_4

+5V_Normal

+5V_Normal

+3.5V_ST

TMDS_CH2-

C

C

MMBD6100 D822

MMBD6100 D824 HDMI-2

10

2

9

3

8

4

7

5

6

NC_4

TMDS_CH1-

NC_3

TMDS_CH1+

GND_2

TMDS_CH2-

NC_1

TMDS_CH2+

1

10

2

9

3

8

4

7

5

6

5V_HDMI_4

OCP_DIODE_ONSEMI D800 MBR230LSFT1G

NC_4

NC_3

GND_2

NC_2

R809 10 HDMI-2

NC_1

ESD_HDMI_NXP

MMBD6100 D825 HDMI-2

2.7K

R823

R824

2.7K

R825

100K OPT R808

OUT_3

OUT_2

OUT_1

OC

+3.3V_Normal

/MHL_OCP_DET

2.7K 2.7K HDMI-2 HDMI-2 DDC_SDA_2

+5V_Normal

8

1

7

2

6

3

5

4

+3.3V_Normal

GND

30V C809 10uF 10V HDMI-2

R806 R822

HDMI-2 IC802 BD82020FVJ

30V

A2

A1

GND_1

NC_2

ESD_HDMI_NXP

C

A2

A1

A2

A1

TMDS_CH2+

1

OCP_DIODE_TSC D800-*1 SS23L

R804 0 HDMI-2

10K HDMI-2

IN_1

IN_2

EN

C802 0.1uF HDMI-2

R821 10K HDMI-2

R814 2.7K HDMI-2

E

TMDS_CH1+

HDMI-2

C

TMDS_CH1-

CEC

R802 0

D827-*1 IP4283CZ10-TBA

Q804 HDMI-2 R827 20K HDMI-2

C B

D826-*1 IP4283CZ10-TBA

R831 300K

B R813 10K HDMI-2

E

B DDC_SCL_4

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

R816 10K HDMI-2

E

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

/VBUS_EN (Active Low)

Q806 HDMI-2

DDC_SDA_4 C

DDC_SCL_2

R815 10K HDMI-2

Q805 HDMI-2

NC4_S7LRM HDMI_R1_S1

MHL_OCP_EN (Active High)

2012/11/07 8 LGE Internal Use Only


Headphone *Option : HEAD_PHONE HEAD_PHONE HP_LOUT

+3.5V_ST

R1505 1K SIDE_HP_MUTE

B

B C R1500 3.3K HEAD_PHONE_POP

OPT C1502 1000pF 50V

C HEAD_PHONE R1501 Q1502 1K MMBT3904(NXP) HEAD_PHONE_POP E

E B B

Q1504 MMBT3904(NXP) HEAD_PHONE_POP

HEAD_PHONE

E HEAD_PHONE_POP Q1501 MMBT3906(NXP)

R1504 10K R1503 1K

C HP_DET

Q1500 MMBT3904(NXP) E HEAD_PHONE_POP

HEAD_PHONE_POP

JK1500 KJA-PH-0-0177

+3.3V_Normal

C

HEAD_PHONE

C1500 10uF 16V

GND

5

L

4

DETECT

3

R

1

HEAD_PHONE

HEAD_PHONE HP_ROUT C1501 10uF 16V

OPT C1503 1000pF 50V

C HEAD_PHONE R1502 Q1503 1K MMBT3904(NXP) HEAD_PHONE_POP E

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

E B

Q1505 MMBT3904(NXP) HEAD_PHONE_POP

B C

NC4_S7LRM

2012/06/20

HEADPHONE

15

LGE Internal Use Only


GLOBAL tuner block except EU and China

BR_RESET_DEMOD

LNA_CTRL_1

FE_TS_SYNC

FE_AGC_SPEED_CTL IF_AGC_SEL

FE_TS_VAL_ERR

FE_BOOSTER_CTL LNA2_CTL

FE_TS_CLK

DEMOD_SCL

LNA_CTRL_2

RF_SWITCH_CTL Pull-up can’t be applied because of MODEL_OPT_2

TU3700 TDSS-G201D

TU3702 TDSH-G501D(B) TUNER_ISOLATOR_DVB_1INPUT_H

DEMOD_SDA

FE_TS_DATA[0]

TUNER_OPT +3.3V_TU R3740-*1 1K TU_IIC_NON_ATSC_1K

+3.3V_TU

R3733 100K

close to TUNER

1 2 3 4 5 6 7 8 9 10 11

R3705

NC

C3701 0.1uF 16V

RESET

0

1

OPT

2 3

SCL

4

SDA +B1[3.3V]

5

SIF

6 7

CVBS

8

IF_AGC

9

DIF[P]

10

DIF[N]

11

B1

A1

C3710 0.1uF 16V

RESET

R3740 1.8K TU_IIC_ATSC_1.8K

R3741 1.8K TU_IIC_ATSC_1.8K

SCL SDA +B1[3.3V]

C3711 18pF 50V

NC_2 C3702

R3735

33

R3736

33

TU_SCL TU_SDA OPT C3742 20pF 50V

C3713 18pF 50V

OPT C3743 20pF 50V

close to TUNER

R3758 82 TU_SIF

16V

OPT

+B2[1.8V] OPT

R3784 0

NC_3

TU_CVBS

IF_AGC

OPT

HALF_NIM/IF_FILTER HALF_NIM/IF_FILTER R3761-*1 R3760-*1 10 10

DIF[P] R3761

DIF[N]

0

HALF_NIM/IF_NON_FILTER R3760

0

HALF_NIM/IF_NON_FILTER

B1 B1

TUNER_RESET

0.1uF

+B2[1.8V]

R3741-*1 1K TU_IIC_NON_ATSC_1K

R3732 100

NC_1

A1

B1

A1

A1 Close to the tuner

IF_P_MSTAR

SHIELD

A2

B2

A2

TU_GND_A

12 B2

IF_N_MSTAR 1. should be guarded by ground 2. No via on both of them 3. Signal Width >= 12mils Signal to Signal Width = 12mils Ground Width >= 24mils

TU_GND_A

+3.3V_TU

+1.8V_TU

C3737 100pF 50V

NON_ASIA

0 R3715

NON_ASIA 0 R3714

TU_GND_A

GND seperation for ASIS tuner

C3708 0.1uF 16V

C3707 100pF 50V

C3738 0.1uF 16V

close to the tuner pin, add,09029

R3704

C3716 0.1uF 16V

100

IF_AGC_MAIN

should be guarded by ground

+3.3V_TU IC3703

+1.8V_TU

AP1117E18G-13

TUNER MULTI-OPTION TU3700-*1 TDSS-H501F(B)

3

TW_FE_LNA FILTER_SETTING CTRL_1

CTRL_2

54MHz~350MHz

1

0

LPF

350Hz~450MHz

0

0

Through

450Hz~870MHz

0

1

HPF

Frequence

Filter_Type

C3717 0.1uF 16V

IN ADJ/GND

1

OUT 2

TUNER_ATSC

1 2 3 4 5 6 7 8 9 10 11 X

B1

A1

NC_1 RESET

R3766 1

C3740 0.1uF 16V

SCL SDA

C3741 10uF 10V 85C

CAP_10uF_X5R CHANGE TO 10UF 10V X5R

+B1[3.3V] NC_2 +B2[1.8] NC_3 IF_AGC

C3741-*1 DIF[P]

10uF 10V CAP_X7R_MP

DIF[N] A1

12 SHIELD

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

NC4_S7LRM TUNER_NON_EU

2012.06.21 14

LGE Internal Use Only


COMPONENT1 & AV(COMMON), AV2 COMP_AV1/2 JK1701 PPJ248-01 7C

[RD3]E-LUG

R1716 10K AV2_R_IN AV2

6C

[RD3]C-SPRING

4C

[RD3]CONTACT

D1700 5.6V AV2_LR_ZENER

R1700 470K AV2

R1718 12K AV2

C1701 1000pF 50V OPT

R1717 10K AV2_L_IN AV2

AV2

5B

D1701 5.6V AV2_LR_ZENER

[WH2]C-SPRING

R1701 470K AV2

R1719 12K AV2

C1702 1000pF 50V OPT

+3.3V_Normal

4A

R1708 10K AV2

[YL]CONTACT

R1711

6A

1K

AV2_CVBS_DET

AV2

D1702 5.6V OPT

[YL]C-SPRING AV2_CVBS_IN

COMP_AV1 JK1702 PPJ245-01

D1713 AV2_CVBS_ZENER_ROHM

7E

[RD2]E-LUG

7A

[YL]E-LUG

7H

[RD2]E-LUG

D1714 AV2_CVBS_ZENER_ROHM

D1713-*1 AV2_CVBS_ZENER_KEC

C1703 47pF 50V AV2

R1702 75 AV2

D1714-*1 AV2_CVBS_ZENER_KEC

R1714 10K COMP2_R_IN

6E

[RD2]C-SPRING

4E

[RD2]CONTACT

6H

D1704 5.6V COMP_LR_ZENER

[RD2]C-SPRING

C1704 1000pF 50V OPT

R1703 470K

R1720 12K

R1715 10K

4H

COMP2_L_IN

[RD2]CONTACT

D1705 5.6V COMP_LR_ZENER

C1705 1000pF 50V OPT

R1704 470K

R1721 12K

+3.3V_Normal

COMPONENT & AV1

5G

[WH1]C-SPRING

[RD1]CONTACT

4F

[RD1]CONTACT

[RD1]C-SPRING

6F

[RD1]C-SPRING

5D

[WH]C-SPRING

4C 6C

R1709 10K

COMP2_DET

R1712 1K

D1706 5.6V OPT

COMP2_Pr+ D1703 COMP_Pr_ZENER_ROHM

8C

[RD1]E-LUG-S

8F

[RD1]E-LUG-S

5B

[BL]C-SPRING

5E

[BL]C-SPRING

D1707 COMP_Pr_ZENER_ROHM

D1703-*1 COMP_Pr_ZENER_KEC

R1705 75

D1707-*1 COMP_Pr_ZENER_KEC

COMP2_Pb+ D1708 COMP_Pb_ZENER_ROHM

4A

[GN]CONTACT

6A

[GN]C-SPRING

4D

[GN]CONTACT

6D

[GN]C-SPRING

D1708-*1 COMP_Pb_ZENER_KEC R1706 75

D1710 COMP_Pb_ZENER_ROHM

D1710-*1 COMP_Pb_ZENER_KEC +3.3V_Normal

R1710 10K AV_CVBS_DET

R1713 1K

7A

[GN]E-LUG

7D

D1709 5.6V OPT

[GN]E-LUG

R1722 0 COMP2_Y+/AV_CVBS_IN D1711 COMP_Y_ZENER_ROHM D1712 COMP_Y_ZENER_ROHM

D1711-*1 COMP_Y_ZENER_KEC

R1707 D1712-*1 COMP_Y_ZENER_KEC

75

CVBS_TEST IC1700 MM1756DURE

VCC

PS

OUT

6

1

5

2

4

3

IN

DTV/MNT_VOUT

GND

BIAS

4.7uF

CVBS_TEST R1723 75

CVBS_TEST C1706 0.1uF

CVBS_TEST C1707 0.1uF

+3.3V_Normal

C1708

CVBS_TEST

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

NC4_S7LRM REAR_NON_EU_L

2012.08.14 17

LGE Internal Use Only


AUDIO 4 AMP(NTP7513)

+3.3V_Normal +3.3V_Normal AMP_RESET

AMP_MUTE

B

50V 22000pF

C3421

3 4

DGND

C3491

0.1uF 50V

10uF

C R3401 AMP_MUTE

35V

C3478

B

100

PVDD1A

PVDD1B 31

32

33

OUT1A

PGND1A

BST1A

RESET

AD

CLK_I

23

BST2A

BCK

9

22

PGND2A

21

OUT2A

15

16

17

18

19

20

BST2B

PGND2B

OUT2B

PVDD2B

PVDD2A

C3403 33pF 50V

C3407 33pF 50V

R3424 5.1K

WOOFER_R C3456 0.1uF 50V

SP-7850_10 R3420 12

R3425 5.1K

C3439 22000pF 50V

C3443 1uF 10V

C3445 1uF 10V

C3447 1uF 10V +24V_AMP_4

+24V

C3440 22000pF 50V

L3417 CIS21J121

C3520 0.1uF 50V

C3519 0.1uF 50V

+24V_AMP_4

C3427

C3431

C3435

0.1uF 50V

0.1uF 50V

10uF 35V

C3422 22000pF 50V

E

22000pF

35

36

GND_IO

VDR2

8

C3405 1000pF 50V

Q3401 MMBT3904(NXP)

10K

37

VDD_IO

AGND

WCK

10

R3417 12

C3455 0.1uF 50V C3453 0.47uF 50V

L3405 10uH

WOOFER_R-

VCC5

R3405 C3487

0.1uF 50V

VDR1

24

MONITOR_2

R3403 10K

C3483

BST1B

27 25

0x56

L3404 10uH SP-7850_10

100

POWER_DET

+24V_AMP_2

PGND1B

28 26

+3.5V_ST

C3516 0.1uF 50V

29

IC3404

14

R3408

URSA_SCL

L3415 CIS21J121

C3515 0.1uF 50V

OUT1B

NTP7513

MONITOR_1

URSA_SDA

THERMAL 41

R3421 12

C3450 390pF 50V

30

7

+24V_AMP_2

+24V

WOOFER_R+

6

SDA

OPT C3437 0.01uF 50V

C3449 390pF 50V

5

100

C3433 10uF 35V

R3416 12

DVDD

AUD_SCK R3407

C3429 0.1uF 50V

SDATA

C3412 1uF 10V

AUD_LRCK

C3496 22000pF 50V

38

[EP]GND 2

GND

13

C3503 1uF 10V

VDD_PLL DGND_PLL

39

40 C3409 0.1uF 16V

AUD_LRCH C3501 1uF 10V

1

MONITOR_0

20 PVDD2A

OPT

C3499 1uF 10V

AGND_PLL

5.1K

12

19 PVDD2B

R3456

11

18

OUT2A

OUT2B

21 17

10

PGND2B

SDA

16

PGND2A

BST2B

22 15

9 14

SPEAKER_R C3512 0.1uF 50V

C3495 22000pF 50V

BST2A

BCK

13

5.1K

C3509 0.47uF 50V

L3411 10uH SP-7850_10 R3451 12

C3411 0.1uF 16V

R3455

SCL

23

R3448 12

C3511 0.1uF 50V

OPT R3414 3.3

FAULT

VDR2

C3463 33pF 50V

L3410 10uH SP-7850_10

+24V_AMP_4

C3425 0.1uF 50V

OPT

PVDD1A

PVDD1B 31

32

PGND1A

BST1A

RESET

OUT1A 33

34

24

C3461 1000pF 50V

Q3403 MMBT3904(NXP)

10K

AD

7

R3435 100

35

SDATA

OPT

100

R3438

R3430 10K

C

CLK_I

AGND

+3.5V_ST

R3428

36

VCC5

25

MONITOR_2

C3459 33pF 50V

37

VDR1

26

0x56

R3452 12

SPK_R-

27

MONITOR_1

100

POWER_DET

BST1B

IC3402

MONITOR_0

R3441

PGND1B

28

NTP7513

12

100

OUT1B

29

6

11 AMP_SCL

R3440

30

5

8

16V

C3506 390pF 50V

4

AUD_SCK AMP_SDA

THERMAL 41

C3417 10uF 10V

SPK_R+

GND

WCK

C3415 0.1uF

R3447 12

DVDD

AUD_LRCK

C3489 10uF 35V

C3505 390pF 50V

DGND C3468 1uF 10V

AUD_LRCH

C3485 0.1uF 50V

OPT C3493 0.01uF 50V

100

3

38

[EP]GND

40 2

SCL

C3465 0.1uF 16V

1

VDD_PLL DGND_PLL

FAULT

OPT

AGND_PLL

GND_IO

16V

C3467 0.1uF 16V

AUD_MASTER_CLK

OPT R3445 3.3 C3481 0.1uF 50V

VDD_IO

C3473 10uF 10V

10K

+24V_AMP_2

R3411

C3477

AUD_MASTER_CLK

39

C3471 0.1uF

22000pF

R3444 10K

R3413

50V

C3475 1000pF 50V

L3408 BLM18PG121SN1D

C3419 1000pF 50V

L3402 BLM18PG121SN1D

34

AMP_RESET

50V

E

P3402 WAFER-ANGLE P3401 WAFER-ANGLE WOOFER_L+ SPK_L+

4

4 WOOFER_L-

SPK_L-

3

3 WOOFER_R+

SPK_R+

2

2 WOOFER_R-

SPK_R-

AMP_MUTE

B

Q3404 MMBT3904(NXP)

10K

AMP_MUTE

35V

B

100 Q3402 MMBT3904(NXP)

10K E

22000pF

C3423

AD

RESET

BST1A

PGND1A

OUT1A

PVDD1A

PVDD1B

36

35

34

33

32

31 28

BST1B

GND

4

27

VDR1

5

IC3403

26

VCC5

DVDD

6

NTP7513

25

AGND

SDATA

7

24

VDR2

WCK

8

23

BST2A

BCK

9

22

PGND2A

SDA

10

21

OUT2A

17

18

19

20

PGND2B

OUT2B

PVDD2B

PVDD2A

100 C R3402

37

PVDD1B 31

R3406

10uF

3

R3419 12

C3457 0.1uF 50V

R3426 5.1K

C3454 0.47uF 50V

L3407 10uH

WOOFER_L C3458 0.1uF 50V

SP-7850_10 R3422 12

R3427 5.1K

C3441 22000pF 50V

C3444 1uF 10V C3442 22000pF 50V

C3446 1uF 10V

C3448 1uF 10V

+24V_AMP_3

+24V

L3416 CIS21J121

100

POWER_DET

R3404 10K

C3492

L3406 10uH SP-7850_10

WOOFER_L-

DGND

16

R3410

C3402 0.1uF 50V

+24V_AMP_1

C3488

DGND_PLL

BST2B

100

+3.5V_ST

0.1uF 50V

PGND1B

15

URSA_SDA

URSA_SCL

C3484

29

MONITOR_2

R3409

L3414 CIS21J121

0.1uF 50V

2

14

C3498 22000pF 50V

C3401 0.1uF 50V

VDD_PLL

0x54

R3423 12

C3452 390pF 50V

OUT1B

MONITOR_1

AUD_SCK

+24V_AMP_1

+24V

CLK_I

PVDD1A 32

PVDD2A

PVDD2B

OUT2B

PGND2B

BST2B

MONITOR_2

MONITOR_1

AUD_LRCK

20

19

C3504 1uF 10V

38

OUT1A 33 18

C3502 1uF 10V

39

PGND1A 34 17

C3500 1uF 10V

C3414 1uF 10V

WOOFER_L+

30 THERMAL 41

OPT C3438 0.01uF 50V

C3451 390pF 50V

1

13

BST1A 35 16

AUD_LRCH

C3410 0.1uF 16V

GND_IO

RESET 36

OUT2A

OPT

C3434 10uF 35V

R3418 12

AGND_PLL

5.1K

C3497 22000pF 50V

VDD_IO

AD 37

21

C3480

[EP]GND

CLK_I 38

10 15

SDA

14

PGND2A

MONITOR_0

R3458

40

GND_IO

SPEAKER_L C3514 0.1uF 50V

12

23

BST2A

22

E

5.1K

C3510 0.47uF 50V

L3413 10uH SP-7850_10

MONITOR_0

VDR2

9

C3462 1000pF 50V

SP-7850_10

R3453 12

C3413 0.1uF 16V

R3457

OPT R3415 3.3 C3430 0.1uF 50V

C3426 0.1uF 50V

11

24

BCK

C3464 33pF 50V

C3513 0.1uF 50V

+24V_AMP_3

SCL

VDR1 AGND

OPT

R3439

100 R3429

BST1B

27 25

R3436 100

PGND1B

28

NTP7513

SCL

C3460 33pF 50V

L3412 10uH

SPK_L-

6

+3.5V_ST

R3431 10K

29

R3450 12

100

POWER_DET

C

OUT1B

DVDD

FAULT

R3443

AMP_SCL

30

26

11

100

R3454 12

C3507 390pF 50V

IC3401

8

16V

C3508 390pF 50V

5

0x54

C3418 10uF 10V

SPK_L+

VCC5

7

0.1uF

R3449 12

DGND

13

AUD_SCK

THERMAL 41

C3416

FAULT

4

OPT C3494 0.01uF 50V

OPT

3

WCK

AUD_LRCK

R3442

C3470 1uF 10V

2

GND

SDATA

AUD_LRCH

AMP_SDA

C3466 0.1uF 16V

VDD_PLL DGND_PLL

12

OPT

1

C3490 10uF 35V

C3486 0.1uF 50V

R3412

AGND_PLL

VDD_IO

[EP]GND

C3469 0.1uF 16V

AUD_MASTER_CLK OPT R3446 3.3

C3482 0.1uF 50V

39

16V

+24V_AMP_1

40

C3474 10uF 10V

22000pF

AUD_MASTER_CLK

0.1uF

L3403 BLM18PG121SN1D

50V C3479

L3409 BLM18PG121SN1D

50V

C3420 1000pF 50V

C3476 1000pF 50V

C3472

AMP_RESET

AMP_RESET

22000pF

+3.3V_Normal +3.3V_Normal

1

1

C3406 1000pF 50V

C3404 33pF 50V

C3408 33pF 50V

C3424

C3517 0.1uF 50V

C3518 0.1uF 50V

+24V_AMP_3

C3428

C3432

C3436

0.1uF 50V

0.1uF 50V

10uF 35V

22000pF 50V

50V

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. NC4_S7LRM AMP_STA380BWEF

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

2012/08/29 34

LGE Internal Use Only


MSTART DEBUG_4PIN

JP_GND4

JP_GND3

JP_GND1

P3900 12505WS-04A00

JP_GND2

MSTAR_DEBUG_4P

1

2

3

RGB_DDC_SCL

4

RGB_DDC_SDA

5

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

NC4_S7LRM MSTAR DEBUG_4PIN

2012/06/20 39

LGE Internal Use Only


RS-232C

RS232C_DEBUG_4P +3.5V_ST

P4000 12507WS-04L

R4001 100

VCC

R4000 100

PM_RXD

PM_TXD

PM_RXD GND

RM_TXD

1

2

3

4 5 GND

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

NC4_S7LRM RS232C_4P_OS

2012/06/20 40

LGE Internal Use Only


IR/LED and Control

+3.5V_ST

R602 10K 1%

R603 10K 1%

CONTROL_NO_FILTER R611 0 CONTROL_FILTER L601 BLM18PG121SN1D

R600 100 KEY1

CONTROL_FILTER C608 0.1uF 16V

CONTROL_FILTER L602 BLM18PG121SN1D

R601 100

IR_8PIN P600 12507WR-08L

IR_10PIN P601 12507WR-10L

KEY2 CONTROL_NO_FILTER R612 0

CONTROL_FILTER C609 0.1uF 16V

1

1

2

+3.5V_ST

2

3

3

L600 BLM18PG121SN1D 4

+3.5V_ST

C602 0.1uF 16V

C603 1000pF 50V

R610 1.8K

4

5

LED_R/BUZZ D601 LED_R_Zener

5

6

6

R607 3.3K 7

IR C604 100pF 50V

7

8

8 9 9

10 +3.3V_Normal

DIGITAL_EYE R608 1K

11

DIGITAL_EYE R609 1K R604

SENSOR_SCL

DIGITAL_EYE R605

SENSOR_SDA

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

100

OPT C605 18pF 50V

100

DIGITAL_EYE

OPT C606 18pF 50V

NC4_S7LRM IR/CONTROL

2012/07/18 6

LGE Internal Use Only


IC102 H27U1G8F2CTR-BC +3.3V_Normal

NC_10 CLE ALE

/PF_CE1 PF_ALE

WE

/PF_WE WP

/PF_WP AR104 22 OS

OS R106 1K

OS R102 3.3K

NC_11 NC_12 NC_13 NC_14 NC_15

34

16

33

17

32

18

31

19

30

20

29

21

28

22

27

23

26

24

25

C103 0.1uF OS

VSS_2 NC_22

1K

15

PCM_D[3]

AE20

PCM_D[4]

AA15

PCM_D[5] PCM_D[6]

AE21 AB21 Y15

LED_R/BUZZ NC_21

OS AR102

NC_20

AUD_MASTER_CLK

I/O3

PCM_A[3]

I/O2

PCM_A[2]

I/O1

PCM_A[1]

I/O0

OPT C112 100pF 50V

NC_18

W22

PCM_A[3]

AB18

PCM_A[4]

AA20

PCM_A[5]

AA21

PCM_A[6]

Y19

PCM_A[7]

AB17

PCM_A[8]

Y16

AUD_MASTER_CLK_0

PCM_A[9]

AB19

PCM_A[10]

AB20

PWM1

PCM_A[11]

AA16

PWM0

PCM_A[12]

AA19

PCM_A[13]

AC21

PCM_A[14]

AA17

56

PCM_A[0]

22

NC_19

V20

PCM_A[2]

AUD_SCK R148

SYM.D PCMDATA[0]/GPIO129 PCMDATA[1]/GPIO130 PCMDATA[2]/GPIO131 PCMDATA[3]/GPIO123 PCMDATA[4]/GPIO122 PCMDATA[5]/GPIO121

AE18

PCMDATA[6]/GPIO120

NF_CE1Z/GPIO141

PCMDATA[7]/GPIO119

NF_WPZ/GPIO196 NF_CEZ/GPIO140

W20

PCM_A[1] OPT

35

10uF 10V CAP_10uF_X7R_OS

CHANGE TO 10UF 10V X5R

VCC_2

1K

36

14

AB22

PCM_A[0]

OPT

13

C102-*1

C102 10uF 10V 85C

R152

37

CAP_10uF_X5R_OS

NC_23

R123

NC_9

38

12

W21 AA18

PCM_D[2]

PCM_A[0-14] NC_24

1K

VSS_1

11

PCM_D[0] PCM_D[1]

PCM_D[7]

1K

VCC_1

39

10

+3.3V_Normal

NC_25

PCMADR[0]/GPIO128

NF_CLE/GPIO139

PCMADR[1]/GPIO127

NF_REZ/GPIO142

PCMADR[2]/GPIO125

NF_WEZ/GPIO143

PCMADR[3]/GPIO124

NF_ALE/GPIO144

PCMADR[4]/GPIO102

NF_RBZ/GPIO145

/PCM_OE

PCMADR[8]/GPIO111

NC_16

/PCM_IORD

/PCM_WE

AD22 AD20

/PCM_IOWR

GPIO_PM[0]/GPIO6

PCMADR[10]/GPIO117

PM_UART_TX/GPIO_PM[1]/GPIO7

PCMADR[11]/GPIO115

GPIO_PM[2]/GPIO8

PCMADR[12]/GPIO107

GPIO_PM[3]/GPIO9

PCMADR[13]/GPIO110

GPIO_PM[4]/GPIO10 PM_UART_RX/GPIO_PM[5]/GPIO11 PM_SPI_SCZ1/GPIO_PM[6]/GPIO12 GPIO_PM[7]/GPIO13 GPIO_PM[8]/GPIO14

PCMOE_N/GPIO116

GPIO_PM[9]/GPIO15

PCMWE_N/GPIO195

PM_SPI_SCZ2/GPIO_PM[10]/GPIO16

PCMIORD_N/GPIO114 PCMIOWR_N/GPIO112

/PCM_CE

AC20 Y18

/PCM_CD

Y21

/PCM_WAIT

Y22

PCM_RST NAND_FLASH_2G_HYNIX

NAND_FLASH_1G_TOSHIBA

EAN60708702 IC102-*1 H27U2G8F2CTR

IC102-*2 TC58NVG0S3ETA0BBBH

NC_2 NC_3 NC_4 NC_5 NC_6 R/B RE CE NC_7 NC_8 VCC_1 VSS_1 NC_9 NC_10 CLE ALE WE WP NC_11 NC_12 NC_13 NC_14 NC_15

1

48

2

47

3

46

4

45

5

44

6

43

7

42

8

41

9

40

10

39

11

38

12

37

13

36

14

35

15

34

16

33

17

32

18

31 30

19 20

29

21

28

22

27

23

26

24

25

NC_29 NC_28 NC_27 NC_26 I/O7

NC_2 NC_3 NC_4 NC_5

I/O6

NC_6

I/O5

RY/BY

I/O4

RE

NC_25 NC_24 NC_23 VCC_2 VSS_2 NC_22 NC_21

CE NC_7 NC_8 VCC_1 VSS_1 NC_9 NC_10

NC_20

CLE

I/O3

ALE

I/O2

WE

I/O1

WP

I/O0

NC_11

NC_19 NC_18 NC_17 NC_16

NC_12 NC_13 NC_14 NC_15

1

48

2

47

3

46

4

45

5

44

6

43

7

42

8

41

9

40

10

39

11

38

12

37

13

36

14

35

15

34

16

33

17

32

18

31

19

30

20

29

21

28

22

27

23

26

24

25

NC_29

NC_1

NC_28

NC_2

NC_27

NC_3

NC_26

NC_4

I/O8

NC_5

I/O7

NC_6

I/O6

RY/BY

I/O5

RE

NC_25

CE

NC_24

NC_7

NC_23

NC_8

VCC_2

VCC_1

VSS_2

VSS_1

NC_22

NC_9

NC_21

NC_10

NC_20

CLE

I/O4

ALE WE

I/O3

WP

I/O2 I/O1

NC_11

NC_19

NC_12

NC_18

NC_13

NC_17

NC_14

NC_16

NC_15

1

48

2

47

3

46

4

45

5

44

6

43

7

42

8

41

9

40

10

39

11

38

12

37

13

36

14

35

15

34

16

33

17

32

18

31

19

30

21

28

22

27

23

26

24

25

NC_1

NC_28

NC_2

NC_27

NC_3

NC_26

NC_4

I/O8

NC_5

I/O7

NC_6

I/O6

R/B

I/O5

RE

NC_25

CE

NC_24

NC_7

NC_23

NC_8

VCC_2

VCC_1

VSS_2

VSS_1

NC_22

NC_9

NC_21

NC_10

NC_20

CLE

I/O4

ALE

I/O3

WE

I/O2

29

20

NC_29

WP

I/O1

NC_11

NC_19

NC_12

V21

USB1_CTL

NC_18

NC_13

NC_17

NC_14

NC_16

NC_15

1

48

2

47

3

46

4

45

5

44

6

43

7

42

8

41

9

40

10

39

11

38

12

37

13

36

14

35

15

34

16

33

17

32

18

31

19

30 29

20

/F_RB

POWER_DET

K6

PM_TXD

K5

INV_CTL

J6

RL_ON

K4

POWER_ON/OFF_1

L6 C2

R146

PM_RXD

33

/SPI_CS

L5

/FLASH_WP

M6

SIDE_HP_MUTE

M5

PM_SPI_CZ0/GPIO_PM[12]/GPIO0

PCMIRQA_N/GPIO108

PM_SPI_SDI/GPIO2

PCMCD_N/GPIO133

PM_SPI_SDO/GPIO3

R20

21

28

22

27

23

26

24

25

U22

NC_29 NC_28

PM_MODEL_OPT_0

M4

AMP_MUTE R147

R180 4.7K

33

SPI_SCK

D3 B2 B1

R151

SPI_SDI

33

SPI_SDO

for SERIAL FLASH

PCMWAIT_N/GPIO103

TS0CLK/GPIO90

E4

MHL_OCP_EN

N25

PM_TXD

NC_26

N24

PM_RXD I/O7

for SYSTEM EEPROM (IC104)

I/O6 I/O5

I2C_SCL

I/O4

I2C_SDA

NC_25

PCM2_CE_N/GPIO134 PCM2_IRQA_N/GPIO135

S7LR-M Multi Package

B8

MODEL_OPT_6

A8

MODEL_OPT_7

CI_TS_CLK CI_TS_VAL CI_TS_SYNC

R136

22

P23

R137

22

P24

TS0DATA_[0]/GPIO80

PCM2_RESET/GPIO137

TS0DATA_[1]/GPIO81 TS0DATA_[2]/GPIO82

UART1_TX/GPIO46

TS0DATA_[3]/GPIO83

UART1_RX/GPIO47

TS0DATA_[4]/GPIO84

UART2_TX/GPIO68

TS0DATA_[5]/GPIO85

UART2_RX/GPIO67

TS0DATA_[6]/GPIO86

UART3_TX/GPIO50

TS0DATA_[7]/GPIO87

I2C_SCKM2/DDCR_CK/GPIO75

TS1VALID/GPI99

I2C_SDAM2/DDCR_DA/GPIO74

TS1SYNC/GPIO100

D2 D1

RGB_DDC_SCL

NC_23 VCC_2

DDCA_DA/UART0_TX

TS1DATA_[0]/GPIO91

DDCA_CK/UART0_RX

TS1DATA_[1]/GPIO92 TS1DATA_[2]/GPIO93

IC101-*1 LGE2121-MS (M1_L13_MS10)

N23

PWM1 VSS_2 NC_22 NC_21

E6 F5

NC_20

B6

I/O3

E5 D5

I/O2 I/O1

B7 E7 F7

I/O0

AB5

NC_19

AB3 A9

NC_18

F4

NC_17

AB1 N6

NC_16

P22

PWM2 C7

AB2 AC2

R21

AB25 GPIO39

LVA0P

GPIO40

LVA0N

GPIO41

LVA1P

GPIO42

LVA1N

GPIO43

LVA2P

GPIO44

LVA2N

GPIO45

LVA3P

GPIO48

LVA3N

GPIO49

LVA4P

GPIO52

LVA4N

GPIO53

P20

AB23

F6 LED_R/BUZZ

AC25

LVB0P

GPIO55

LVB0N

I2C_SCKM0/GPIO56

LVB1P

I2C_SDAM0/GPIO57

LVB1N

GPIO76

LVB2P

GPIO77

LVB2N LVB3P LVB3N LVB4P

CI_TS_DATA[0-7]

Y13

CI_TS_DATA[0]

Y11

CI_TS_DATA[1]

AA12

CI_TS_DATA[2]

AB12

CI_TS_DATA[3]

from CI SLOT

CI_TS_DATA[4]

AA14 AB14

CI_TS_DATA[5]

AA13

CI_TS_DATA[6]

AB11

CI_TS_DATA[7] FE_TS_CLK FE_TS_VAL_ERR FE_TS_SYNC FE_TS_DATA[0-7]

PWM0/GPIO69

TS1DATA_[4]/GPIO95

PWM1/GPIO70

TS1DATA_[5]/GPIO96

PWM2/GPIO71

TS1DATA_[6]/GPIO97

PWM3/GPIO72

TS1DATA_[7]/GPIO98

AD15 AC16 AD16

FE_TS_DATA[0]

AE15

FE_TS_DATA[1]

AE14

FE_TS_DATA[2]

AC13

FE_TS_DATA[3]

AC14

FE_TS_DATA[4]

AD12

FE_TS_DATA[5]

AD13

FE_TS_DATA[6]

AD14

FE_TS_DATA[7]

Internal demod out FE_TS_DATA[0] FE_TS_DATA[0]

PWM4/GPIO73 PWM_PM/GPIO197

AB24 AD25

H6 KEY1

AC24

G5

KEY2

AE23

G4

AC23

J5

AC22

J4

AD23

SCART1_MUTE

SCART1_MUTE

SAR0/GPIO34 SAR1/GPIO35 SAR2/GPIO36 SAR3/GPIO37 SAR4/GPIO38

V23

GPIO54

TS1DATA_[3]/GPIO94

P21 PWM0

Y12

AC15 TS1CLK/GPIO101

S7LR-M_MS10

AA10

TS0SYNC/GPIO89

PCM2_WAIT_N/GPIO136

UART3_RX/GPIO51

RGB_DDC_SDA

NC_24

TS0VALID/GPIO88

PCM2_CD_N/GPIO138

D4 /MHL_OCP_DET

NC_27

+3.5V_ST

PANEL_CTL

C1

Y14 USB1_OCD

PCM_5V_CTL NC_1

PF_ALE

AD19

PCM_RESET/GPIO132

T20 NC_1

PCMCE_N/GPIO118

U21

EAN61857001 IC102-*4 K9F1G08U0D-SCB0

EAN60991001 IC102-*3 TC58NVG1S3ETA00

/PF_WE

AE17

A2 PM_SPI_SCK/GPIO1

NAND_FLASH_1G_SS

NAND_FLASH_2G_TOSHIBA

EAN61508001

/PF_OE

AD17

GPIO_PM[11]/GPIO17

AD21 /PCM_IRQA

/PF_CE1

AC19

H5

PCMADR[9]/GPIO113

PCMREG_N/GPIO126

AA22

/PF_CE0

AC18

PCMADR[7]/GPIO106

AB15 NC_17

/PF_WP

AD18

PCMADR[6]/GPIO105

Y20 /PCM_REG

AC17

PCMADR[5]/GPIO104

PCMADR[14]/GPIO109 R153

OPT R105 1K

NC_8

PCM_A[4]

R124

+3.3V_Normal

OS C101 0.1uF

PCM_A[5]

I/O4

PCM_D[0-7]

Boot from 8051 with SPI flash Secure B51 without scramble Secure B51 with scramble Boot from MIPS with SPI flash Boot from MIPS with SPI flash Boot from MIPS with SPI flash Secure MIPS without scramble Scerur MIPS with SCRAMBLE

1K

OPT R108 1K

40

9

I/O5

4’b0000 4’b0001 4’b0010 4’b0100 4’b0101 4’b0110 4’b1001 4’b1010

OS

NC_7

41

8

PCM_A[6]

: : : : : : : :

NON_OS

/PF_CE0

42

I/O6

B51_no_EJ SB51_WOS SB51_WS MIPS_SPE_NO_EJ MIPS_SPI_EJ_1 MIPS_SPI_EJ_2 MIPS_WOS MIPS_WS

1K

CE

43

7

PCM_A[7]

OPT

/PF_OE

6

I/O7

R165

RE

S7LR-M_NON_MS10 IC101 MSD804KKX

<CHIP Config> (I2S_OUT_BCK,I2S_OUT_MCK,PAD_PWM1PAD_PWM0)

R117

R/B

/F_RB

44

5

NC_26

1K

NC_6

45

4

PCM_A[0-7]

OS 22 AR101

NC_27

1K

OS AR103 22

NC_5

46

3

1’b0 1’b1

NC_28

R121

OS R109 3.9K

47

R118

OS R107 1K

EAN35669103

2

1K

NC_4

NAND_FLASH_1G_HYNIX

NC_29

OPT

NC_3

48

R115

NC_2

<CHIP Config(LED_R/BUZZ)> Boot from SPI CS1N(EXT_FLASH) Boot from SPI_CS0N(INT_FLASH)

+3.3V_Normal 1

1K

NC_1

R116

NAND FLASH MEMORY

R23 VSYNC_LIKE/GPIO146

U24 V25

R24 V-COM_SCL

V24 W25 W23 AA23

V-COM_SCL

V-COM_SDA

V-COM_SDA

SENSOR_SCL

SENSOR_SCL

SENSOR_SDA

SENSOR_SDA

R25 T21 T22

SPI1_CK/GPIO199 SPI1_DI/GPIO200 SPI2_CK/GPIO201 SPI2_DI/GPIO202

Y24 AA25 AA24

LVB4N AE24

DIMMING

LVACLKP

I2C

+3.3V_Normal

LVACLKN LVBCLKP

AD24 Y23 W24

S7LR-M_NON_MS10 IC101 MSD804KKX

LVBCLKN OPT R156

T25

10K

R157

PWM0

GPIO194 R140 1K

100

R141 1K

GPIO191

R145 2.2K

R144 2.2K

GPIO192

PWM2

PWM_DIM

U23 T24 T23

OPT C111 2.2uF

AMP_RESET FRC_RESET

AMP_SDA AMP_SCL

FRC_RESET 5V_DET_HDMI_2 5V_DET_HDMI_4

I2C_SDA

AV_CVBS_DET

I2C_SCL

AV2_CVBS_DET SC1/COMP1_DET HP_DET S2_RESET TUNER_RESET

PM MODEL OPTION EEPROM

MODEL_OPT_0 +3.5V_ST

5V_DET_HDMI_1

5V_DET_HDMI_1 MODEL_OPT_1

+3.3V_Normal

LNA_CTRL_1 LNA_CTRL_2

NVRAM_RENESAS

NVRAM_ST

IC104 M24256-BRMN6TP

C105 0.1uF

IC104-*1 R1EX24256BSAS0A

NON_OS_512k_ST

NON_OS_512k_ATMEL

IC104-*2 M24512-RMN6TP

IC104-*3 AT24C512C-SSHD-T

R174 10K S/W_TW

R177 10K HD_LVDS_NON_EU PM_MODEL_OPT_0 PM_MODEL_OPT_1

E0

E1

8

1

2

7

VCC A0

VSS

3

4

6

5

8

VCC

E0

1

8

VCC

A0

1

8

VCC

WC A1

A0’h E2

1

SCL

R111

SDA

R112 C104 8pF OPT

22 22

I2C_SCL I2C_SDA

C106 8pF OPT

A2

VSS

2

7

3

6

4

5

WP

E1

SCL

E2

SDA

7

3

6

4

5

A1

SCL

A2

SDA

GND

2

7

3

6

4

5

WP

SCL

SDA

R175 10K S/W_EU/AJ

R176 10K HD_LVDS_EU

MODEL_OPT_2

PM_MODEL_OPT_0 HIGH : HD_NON_EU LOW : HD_EU HD_LVDS_pattern is different. Between EU and NON_EU PM_MODEL_OPT_1 HIGH : S/W_NON_EU LOW : S/W_EU/AJ S/W is different. Between TW

BR_RESET_DEMOD

E6 F5 B6 E5 D5 B7 E7 F7 AB5 AB3 A9 F4 AB1 N6 AB2 AC2

GPIO39

LVA0P

GPIO40

LVA0N

GPIO41

LVA1P

GPIO42

LVA1N

GPIO43

LVA2P

GPIO44

LVA2N

GPIO45

LVA3P

GPIO48

LVA3N

GPIO49

LVA4P

GPIO52

LVA4N

GPIO53

EAN43349003

AB25 AB23 AC25 AB24 AD25 AC24 AE23 AC23 AC22 AD23 V23

GPIO54

LVB0P

GPIO55

LVB0N

I2C_SCKM0/GPIO56

LVB1P

I2C_SDAM0/GPIO57

LVB1N

GPIO76

LVB2P

GPIO77

LVB2N LVB3P LVB3N LVB4P

U24 V25 V24 W25 W23 AA23 Y24 AA25 AA24

LVB4N AE24 LVACLKP LVACLKN LVBCLKP

AD24 Y23 W24

LVBCLKN

RXA0+ RXA0RXA1+ RXA1RXA2+ RXA2RXA3+ RXA3RXA4+ RXA4RXB0+ RXB0RXB1+ RXB1RXB2+ RXB2RXB3+ RXB3RXB4+ RXB4RXACK+ RXACKRXBCK+ RXBCK-

T25 GPIO194 GPIO191

EAN62389501

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

VSS

2

WC

SYM.A

C7

GPIO193

GPIO192

EAN43349004

MODEL_OPT_3

U23

MODEL_OPT_4

T24

MODEL_OPT_5

T23

MODEL_OPT_8

GPIO193

NC4_S7LRM MAIN1_NON_EU

2012/09/19 51

LGE Internal Use Only


Memory OPTION

MODEL OPTION

MODEL_OPT_1

R225 R228

OPT

100

MODEL_OPT_5

R230

OPT

100

MODEL_OPT_6

R229

OPT

100

MODEL_OPT_7

R213

OPT

100

MODEL_OPT_8

MODEL_OPT_3

MODEL_OPT_6

PIN NO. U23

PIN NO. B8

0

0

0

1

256M

1

0

MODEL_OPT_4

U23

MIU0-128M

MIU0-256M

MODEL_OPT_5

T24

NON_DVB_S

DVB_S

MODEL_OPT_6

B8

MIU1-NO_DDR

MIU1-128M

256M+128M

1

1

MODEL_OPT_7

A8

NON_DUALSTREAM

DUALSTREAM

CK-_HDMI1

D0+_HDMI1

D0+_HDMI1

D0-_HDMI1 D1+_HDMI1

D0-_HDMI1 D1+_HDMI1

D1-_HDMI1

D1-_HDMI1

D2+_HDMI1

D2+_HDMI1

D2-_HDMI1

D2-_HDMI1

DDC_SDA_1

DDC_SDA_1

DDC_SCL_1

DDC_SCL_1

HPD1

HPD1

+1.10V_VDDC

Ginga

Normal Power 3.3V

IF_P_MSTAR

H9 L204 BLM18PG121SN1D

J3 K3 J1 K2 K1 L2 L3 T5 T4 V5

RXACKP RXACKN

47

C251

0.1uF R218

47 C264 1000pF OPT 50V

AC4 NC_8

ANALOG SIF Close to MSTAR

AD3

NC_9

RXA0P IP

RXA1P

IM

RXA1N SIFP

RXA2N

SIFM

M13

C204-*1

N12 P14

10uF 10V CAP_10uF_X7R

P15

CHANGE TO 10UF 10V X5R

R10 R14

FB_CORE

R15 T10

L208 BLM18PG121SN1D

L227 BLM18PG121SN1D HALF_NIM/EU_NON_T2

DDCDA_CK/GPIO26

P19

FB_CORE

HALF_NIM/EU_NON_T2 R220 10K HALF_NIM/EU_NON_T2 R219 0

AD2

GND_33 GND_34

VDDC_2

GND_35

VDDC_3

GND_36

VDDC_4

GND_37

VDDC_5

GND_38

VDDC_6

GND_39

VDDC_7

GND_40

VDDC_8

GND_41

VDDC_9

GND_42

VDDC_10

GND_43

VDDC_11

GND_44

VDDC_12

GND_45

VDDC_13

GND_46

VDDC_14

GND_47 GND_49

P10

C241 0.1uF

C240 0.1uF

HOTPLUGA/GPIO22

GND_32

VDDC_1

GND_48

AC5 HALF_NIM/EU_NON_T2 C282 0.1uF

R16 L11 M14

MIUVDDC

NC_2

GND_50

FB_CORE

GND_51

AVDDL_MOD

GND_52

NC_1

GND_53

DVDD_DDR

GND_54

IF_AGC_MAIN

AE2

TUNER_I2C AE6

X201-*1 24.0MHz X-TAL_LIHOM

TU_SCL

AD6

TU_SDA

I2C_SDAM1/GPIO79

GND_55

C285 0.047uF 25V HALF_NIM/EU_NON_T2

RF_AGC

I2C_SCKM1/GPIO78

M12

+3.3V_Normal

AE3

DDCDA_DA/GPIO27

IF_AGC

L10

10uF 10V CAP_10uF_X7R

AVDD_AU33

AD4

RXA2P

K11

0.1uF

0.1uF

CHANGE TO 10UF 10V X5R

AC3

RXA0N

HDMI FOR LN52

TU_SIF

C259

0.1uF R216

C255

SYM.C

C250

0.1uF

HALF_NIM/IF_FILTER C289 33pF

CAP_10uF_X5R C284

HALF_NIM/EU_NON_T2 HALF_NIM/EU_NON_T2

K10

C284-*1 0.1uF

IF_N_MSTAR

C245

0.1uF

C235

C258

0.1uF

100

G10 AVDDLV_USB

G9

C209

R289

K12

VDD33

+3.3V_Normal

HALF_NIM/IF_FILTER C288 33pF

10V 85C

OPT

10uF

C287

C204

0.1uF

10V85C

C257

100

HALF_NIM/EU_NON_T2 HALF_NIM/EU_NON_T2

10uF

R288

MODEL_OPT_6 MODEL_OPT_4

GND_56

W9

AVDD2P5

W10 W11 W12

AVDD2P5_ADC_1

GND_57

AVDD2P5_ADC_2

GND_58

AVDD2P5_ADC_3

GND_59

AVDD2P5_ADC_4

GND_60

Close to MSTAR XTAL_LOAD_27pF C261 27pF

AD1

AE9 CK+_HDMI4

AC9

CK-_HDMI4 R214

D0+_HDMI4

R215

D0-_HDMI4 D1+_HDMI4

2.2 HDMI-2

AC10

2.2 HDMI-2

AD9 AC11 AD10

D1-_HDMI4

AE11

D2+_HDMI4

AD11

D2-_HDMI4

AE8

DDC_SDA_4

AD8

DDC_SCL_4

AC8

HPD4

SPDIF_IN/GPIO150

RXCCKN

SPDIF_OUT/GPIO151

F3 G3

D0+_HDMI2

F1

D0-_HDMI2 D1+_HDMI2

G2 G1

D1-_HDMI2

H2

D2+_HDMI2

H3

D2-_HDMI2

R6

DDC_SDA_2

U6

DDC_SCL_2

P5

HPD2

R4

CEC_REMOTE_S7

RXC1P

USB0_DM

RXC1N

USB0_DP

RXC2P RXC2N

USB1_DM

DDCDC_DA/GPIO31

USB1_DP

N3 N1 M3

SC1_ID

M2

SC1_FB

M1

SC1_R+/COMP1_Pr+

D6

R296

100

I2S_IN_SD/GPIO149

RXBCKN

I2S_IN_WS/GPIO147

RXB0P

SPDIF_OUT

AVDD25_PGA

SPDIF_OPTIC

Normal 2.5V

I2S_OUT_BCK/GPIO154

RXB1P

I2S_OUT_MCK/GPIO152

RXB1N

I2S_OUT_SD/GPIO155

+2.5V_Normal

NC_3

GND_68

NC_4

GND_69 GND_70

AVDD_NODIE

GND_71 GND_72

L7 M7

AVDD2P5:172mA

L211 BLM18PG121SN1D

SIDE_USB1_DM

AE12

P7

SIDE_USB1_DP

CAP_10uF_X5R

AMP_SCL

D8

AMP_SDA

D9

CHANGE TO 10UF 10V X5R

COMP2_DET

R7

10uF 10V 85C

C273 0.1uF

C260 1uF

C274 0.1uF

AVDD_AU33

AUD_SCK

AVDD25_PGA:13mA

AUD_MASTER_CLK_0

B9

VDD33

L229 BLM18PG121SN1D

AUD_LRCH

I2S_I/F C10

AUD_LRCK

I2S_OUT_WS/GPIO153

HOTPLUGB/GPIO23

AVDD_DVI_USB_2

GND_74

AVDD3P3_MPLL

GND_75

AVDD_DMPLL

GND_76 GND_77 GND_78 GND_79

V7 AVDD_AU33

GND_80

AVDD_EAR33

GND_81 GND_82

R19 T19

C291 0.1uF 16V

GND_73

DVDD_NODIE

AVDD2P5_MOD

C9

AVDD_DVI_USB_1

M19

W7

RXB2N DDCDB_CK/GPIO28

GND_67

AVDD2P5

RXB2P DDCDB_DA/GPIO29

GND_65

U7

AVDD_NODIE

E2

W15

AVSS_PGA

SIDE USB

B10

RXB0N

AVDD_MOD_2

W14

C8

RXBCKP

GND_64 GND_66

AVDD_DMPLL

I2S_IN_BCK/GPIO148

GND_63 AVDD_MOD_1

XTAL_LOAD_27pF

DDCDC_CK/GPIO30

VDDP_1

GND_83

VDDP_2

GND_84 GND_85

W18

C269-*1

W19

10uF 10V CAP_10uF_X7R

VDD33

AVDD_LPLL_1

GND_86

AVDD_LPLL_2

GND_87 GND_88

V19 VDDP_NAND

GND_89 GND_90

AB9 AUR0

P2

P3

U19

AC12

AUL0

N2

27pF

GND_62

V18

AVDD2P5_MOD

XTAL_LOAD_30pF C262-*1 30pF

E3

CEC/GPIO5

R3

AVDD25_LAN

SPDIF_OUT

RXC0N

F2 CK+_HDMI2

C262

GND_61

Y17

CI_DET

RXC0P

HOTPLUGC/GPIO24

CK-_HDMI2

X-TAL_SUNNY

D7 RXCCKP

1M

HOTPLUGD/GPIO25

X201 24MHz

XTAL_LOAD_30pF C261-*1 30pF

C269

HDMI

R5 PM_MODEL_OPT_1

AC1

R287

XIN XOUT

HSYNC0

AUL1

VSYNC0

AUR1

RIN0P

AUL2

RIN0M

AUR2

GIN0P

AUL3

GIN0M

AUR3

BIN0P

AUL4

BIN0M

AUR4

AA11

+1.5V_DDR

K15

AA9

K16

AA7

C238

2.2uF

AV2

AB8

C239

2.2uF

AV2

C242

2.2uF

C243

2.2uF

Y8 Y10

L15

AV2_L_IN AV2_R_IN

AVDD_DDR0_D_1

GND_92

AVDD_DDR0_D_2

GND_93

AVDD_DDR0_D_3

GND_94

AVDD_DDR0_C

GND_95 GND_96

K17

COMP2_L_IN

L17

COMP2_R_IN

AC7

GND_91

J17

Y9

M17 L16

AD7

AVDD_DDR1_D_1

GND_97

AVDD_DDR1_D_2

GND_98

AVDD_DDR1_D_3

GND_99

AVDD_DDR1_C

SOGIN0

GND_100 GND_101

AUDIO IN

CHANGE TO X5R

SC1_G+/COMP1_Y+

GND_102

E9

SC1_B+/COMP1_Pb+

GND_EFUSE

V2

SC1_SOG_IN

V3

SC1_CVBS_IN

U3

SC1/COMP1_L_IN

U2

SC1/COMP1_R_IN

T1

DEMOD_SCL

T2

DEMOD_SDA

R2 R1 T3

HSYNC1 VSYNC1

W6 GPIO_PM[13]/GPIO19

RIN1P

AUOUTL2

RIN1M

AVDD5V_MHL

GIN1P

GPIO_PM[14]/GPIO20

GIN1M

AUOUTR2

BIN1P

GPIO_PM[15]/GPIO21

AUDIO OUT

MHL_CD_SENSE

V6

B17

AVDD5V_MHL

Y7

DDR3 1.5V

/VBUS_EN

W5

C23 A5

SCART1_Rout

U5

C11

TP209

C19

BIN1M

C22 D14

AVDD_DDR0:55mA +1.5V_DDR

D18 D19

AA2

0.047uF

W3

C224

1000pF

W1

BIN2P

AUVAG

BIN2M

AUVRP

SOGIN2

CVBS In/OUT R244

TU_CVBS

33

C225

Y4

COMP2_Y+/AV_CVBS_IN AV2_CVBS_IN

R246

33

C227

0.047uF

R249

33

C230

0.047uF AA5

AV2

Y5

AV2

W4

AA4 Y6 AA1

DTV/MNT_VOUT

50V

R252

68

C233

0.047uF

CVBS1

L205

5.6uH

H/P OUT

HEAD_PHONE

RP/GPIO63

CVBS3

TP/GPIO60

NC_5

HEAD_PHONE

C5

EPHY_RP

EPHY_RP

EPHY_TP

EPHY_TP

F18

C268 4.7uF 10V HEAD_PHONE

G8

AVDD_DDR1:55mA

H8

C272 4.7uF 10V HEAD_PHONE

N22 N21 N20 M22 M21

RN/GPIO66

NC_6

LED1/GPIO59

EPHY_RN

C4

EPHY_RN

SOC_RESET

TN/GPIO62 GPIO61 GPIO64 GPIO65

EPHY_TN

C3 A3 B3 B4

EPHY_TN

URSA_SDA

URSA_SDA

URSA_SCL

URSA_SCL

POWER_DET_RESET

+3.5V_ST

1 IRIN/GPIO4 ARC0 HWRESET

T6 N5

R210

0

HDMI1_ARC

C231

1uF

HDMI1_ARC

IR HDMI_ARC

F10 V15 W16

SWITCH_NAMAE SW200 JTP-1127WEM

RESET_IC_SOC_RESET R266 470 C202 4.7uF 10V RESET_IC_SOC_RESET

M20

SWITCH_POSTEC SW200-*1 TMSV153BRA

B5

N4

C200 4.7uF 10V

V8

+3.5V_SOC_RESET C201 0.1uF

GND_1

GND_106

GND_2

GND_107

GND_3

GND_108

GND_4

GND_109

GND_5

GND_110

GND_6

GND_111

GND_7

GND_112

GND_8

GND_113

GND_9

GND_114

GND_10

GND_115

GND_11

GND_116

GND_12

GND_117

GND_13

GND_118

GND_14

GND_119

GND_15

GND_120

GND_16

GND_121

GND_17

GND_122

GND_18

GND_123

GND_19

GND_124

GND_20

GND_125

GND_21

GND_126

GND_22

GND_127

GND_23

GND_128

GND_24

GND_129

GND_25

GND_130

GND_26

GND_131

GND_27

GND_132

GND_28

GND_133

GND_29

GND_134

GND_30

GND_135

GND_31

GND_136

G11 G12 G13 G14 G17 G18 G19 G24 H11 H12 H13 H14 H15 H16 H17 H18 H19 J9 J10 J11 J12 J13 J14 J15 J16 J18 J19 J25 K9 K13 K14 H10 K18 K19 K22 L8 L9 J8 L12 L13 L18 L19 M8 K8 M10 M11 L14 M15 M16 M18 M25 N10 N11 N13 N14 N15 N16 N17 N19 K7 P8 P9 M9 P11 P13 P16 P17 P18 P12 R8 R9 R11 R12 R13 R17 T8 T9 N7 T11 T12 T13 T14 T15 T16 T17 U8 U9 U10 U11 U12 U13 U14 U15 U16 U17 R18 V9 V10 V11 V12 V14 V17 T7 E8

+1.10V_VDDC AVDD_NODIE

MIUVDDC

L206 BLM18PG121SN1D

L228 BLM18PG121SN1D

AVDD_DMPLL SOC_RESET

SOC_RESET

T18

STby 3.5V +3.5V_ST

SWITCH R205 100 R217 0

R200 62K

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

F17 F19

HP_ROUT

LED0/GPIO58

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

F8

A6

NC_7

VCOM

E22

HP_LOUT

C6

CVBS2

AB4

Close to MSTAR

AB6

5.6uH

CVBS0

CVBSOUT1 C203 1000pF OPT

L203

EARPHONE_OUTR

0.047uF AA8

C263 10uF

AC6 AA6

EARPHONE_OUTL

C256 0.1uF

1uF

C223

AE5

C253 1uF

C254

68

GIN2M

C249 4.7uF

C207

R242

V1

E19

AD5 AUVRM

0.1uF

0.047uF 0.047uF

GIN2P

C248

C221 C222

Y3

R241

68 33

RIN2M

0.1uF

W2

10uF 10V

0.047uF

C278

C220

0.1uF

33

C266

R239

E18

2

0.047uF AA3

4

C219

3

68

E17 L202 BLM18SG121TN1D

RIN2P

1

Y2

2

0.047uF

R238 R240

COMP2_Pb+

C218

4

COMP2_Y+/AV_CVBS_IN

33

HSYNC2

3

R237

COMP2_Pr+

GND_105

A23

SCART1_Lout

V4

GND_103 GND_104

SOGIN1

COMP2

SYM.E

S7LR-M_NON_MS10

DTV_IF

CAP_10uF_X5R

Close to MSTAR FHD

1K

+1.10V_VDDC

1K

S/W_NON_AJ

R212

IC101 MSD804KKX

* Dual Stream is only Korea 3D spec

R227

NON_DVB_T2

1K

1K

NON_M120

R207

R209

MIU0-128M

1K

NON_DVB_S

R223

1K

1K

MIU1-NO_DDR

R224

1K OPT

R293

R297 CK-_HDMI1

0.1uF

128M+128M

M120

C283

NON_M120

1uF

T25

1uF

MODEL_OPT_3

C280

S/W_AJ DVB_T2

C277

NON_DVB_T2

S/W_NON_AJ

10V

AB2

10V

F4

MODEL_OPT_2

J2 CK+_HDMI1

VDDC 1.05V VDDC : 2026mA

128M

S7LR-M_NON_MS10 IC101 MSD804KKX

CK+_HDMI1

+1.10V_VDDC

Note

MODEL_OPT_4

1K

R204

MODEL_OPT_4

HD

FHD

MODEL_OPT_1

MODEL_OPT_2

OPT 100 OPT 100

AB3

Memory

C275

1K HD

1K S/W_AJ

R211

R226

1K DVB_T2

1K M120

R208

R206

1K

MIU0-256M

DVB_S R221

1K

1K

MIU1-128M

R291

MODEL_OPT_0

R294

RF_SWITCH_CTL

OPT 100 R201 R202 BOOSTER_OPT100 R203 RF_SW_OPT 0

NON_DUALSTREAM

LNA2_CTL

R222

1K

1K OPT

R290

R298 IF_AGC_SEL

DUALSTREAM

MODEL_OPT_0

HIGH

LOW

10uF

MODEL OPTION

PIN NO.

C228

PIN NAME

+3.3V_Normal

+2.5V_Normal

10uF

+2.5V_Normal +3.3V_Normal

C286 0.1uF

C252 0.1uF C296 10uF 10V

L207 BLM18PG121SN1D

C279 0.1uF

C205 0.1uF

NC4_S7LRM

MAIN2_NON_EU

2012.09.19 52

LGE Internal Use Only


+1.5V_DDR

+1.5V_DDR

1uF

1uF

C1241

1uF

C1238

1uF

C1219

1uF

C1218

C1217

0.1uF

0.1uF

C1239

C1206

C1251

A-MVREFCA

10uF10V

1000pF

0.1uF C1204

1%

R1204 R1205

1K

C1203

C1202

1K 1%

A-MVREFDQ

1000pF

0.1uF

1K 1% 1% 1K

C1201

R1202

R1201

+1.5V_DDR

CLose to Saturn7M IC

CLose to DDR3

DDR_1600_2G_HYNIX IC101 MSD804KKX

IC1201 H5TQ2G63DFR-PBC EAN61829203 N3

M8 A0 A1 A2 A3 A4 R1203

A5

L8 ZQ

+1.5V_DDR

240 1%

A7 A8

B2 10V 10uF

C1205

D9

10V 10uF

C1227

G7

C1207

0.1uF

K2

C1208

0.1uF

K8

C1210

0.1uF

N1

C1211

0.1uF

N9

C1212

0.1uF

R1

C1213

0.1uF

R9

C1214

0.1uF

C1215

0.1uF

VDD_1

A9

VDD_2

A10/AP

VDD_3

A11

VDD_4

A12/BC

VDD_5

A13

VDD_6 VDD_7 VDD_9

C1 C9 D2 E9 F1 H2 H9

L1 L9 T7

R8 R2 T8 R3 L7 R7 N7 T3

M2 BA0

N8 M3

BA2 VDDQ_1 CK

VDDQ_3

CK

VDDQ_4

K9

CS

VDDQ_7

ODT

VDDQ_8

RAS

VDDQ_9

CAS

K1 J3 K3 L3

WE NC_1

T2 RESET

NC_4

F3 DQSL

G3 C7

A9

G8 J2 J8 M1 M9 P1 P9 T1 T9

VSS_1

DQSU

VSS_2

DQSU

VSS_3 VSS_4

DML

VSS_5

DMU

VSS_6

D8 E2 DDR_1600_2G_SS

DDR_1600_2G_NANYA

DDR_1600_1G_HYNIX

IC1201-*1 K4B2G1646E-BCK0

IC1201-*2 NT5CB128M16FP-DI

IC1201-*3 H5TQ1G63EFR-PBC

EAN61848802

EAN61859702

N3 P7 P3 N2 P8 P2 R8 R2 T8 R3 L7 R7 N7 T3

M8 A0

A3

L8

K7

T8

A9

VDD_1

A10/AP

VDD_2

A11

VDD_3

A12/BC

VDD_4

A13

VDD_5

NC_5

VDD_7

BA0

VDD_9

VDD_6 VDD_8

K3 L3

R7 N7

K8

T3

N1 N9 R9

CK

VDDQ_3 VDDQ_4 VDDQ_5

CS

VDDQ_6

ODT

VDDQ_7

RAS

VDDQ_8

CAS

VDDQ_9

RESET

NC_2 NC_3 NC_4

F3 DQSL

C1

K7 K9

K1 J3

H9

K3 L3

J9

DQSU DQSU

F7 F2 F8 H3 H8 G2 H7

DML

VSS_4 VSS_5 VSS_6

DQL0

VSS_7

DQL1

VSS_8

DQL2

VSS_9

DQL3

VSS_10

DQL4

VSS_11

DQL5

VSS_12

C3 C8 C2 A7 A2 B8 A3

VDD_5

NC_6

VDD_7

BA0

VDD_9

VDD_6 VDD_8

R3 L7

G7

R7

K2

N7

K8

T3

N1 N9 R9

VDDQ_2

CK

VDDQ_3 VDDQ_4 VDDQ_5

CS

VDDQ_6

ODT

VDDQ_7

RAS

VDDQ_8

CAS

VDDQ_9

A9

C7 B7

NC_2 NC_4

DQSL

G8

E7

J2

D3

J8 M1

C1

K7 K9

K1 J3

H9

K3 L3

M9

F7 F2

P9

F8

T1

H3 H8 G2 H7

VSSQ_2

DQU1

VSSQ_3

DQU2

VSSQ_4

DQU3

VSSQ_5

DQU4

VSSQ_6

DQU5

VSSQ_7

DQU6

VSSQ_8

DQU7

VSSQ_9

B9

DML

VSS_4

DMU

VSS_5 VSS_6

DQL0

VSS_7

DQL1

VSS_8

DQL2

VSS_9

DQL3

VSS_10

DQL4

VSS_11

DQL5

VSS_12

D1

C3

D8

C8

E2

C2

E8

A7

F9

A2

G1

B8

G9

A3

VDD_1 VDD_2

A11

VDD_3

A12/BC

VDD_4

NC_7

VDD_5

NC_5

VDD_7

BA0

VDD_9

VDD_6 VDD_8

R3 L7

G7

R7

K2

N7

K8

T3

N1 N9

EAN61836301

EAN61859501

R9

VDDQ_2

CK

VDDQ_3 VDDQ_4 VDDQ_5

CS

VDDQ_6

ODT

VDDQ_7

RAS

VDDQ_8

CAS

VDDQ_9

NC_2 NC_4

DQSL

C1

K7 K9

K1 J3

H9

K3 L3

A9

C7 B7

G8

E7

J2

D3

J8 M1 M9

F7 F2

P9

F8

T1

H3 H8 G2 H7

VSSQ_2

DQU1

VSSQ_3

DQU2

VSSQ_4

DQU3

VSSQ_5

DQU4

VSSQ_6

DQU5

VSSQ_7

DQU6

VSSQ_8

DQU7

VSSQ_9

B9

DML

VSS_4

DMU

VSS_5 VSS_6

DQL0

VSS_7

DQL1

VSS_8

DQL2

VSS_9

DQL3

VSS_10

DQL4

VSS_11

DQL5

VSS_12

D1

C3

D8

C8

E2

C2

E8

A7

F9

A2

G1

B8

G9

A3

VDD_3

A12/BC

VDD_4

A13

VDD_5

NC_5

VDD_7

BA0

VDD_9

VDD_6 VDD_8

R3 L7

G7

R7

K2

N7

K8

T3

N1 N9 R9

VDDQ_2

CK

VDDQ_3 VDDQ_4 VDDQ_5

CS

VDDQ_6

ODT

VDDQ_7

RAS

VDDQ_8

CAS

VDDQ_9

NC_2 NC_4

DQSL

C1

K7

C9

K9

K1 J3

H9

K3 L3

J9

A9

C7 B7

G8

E7

J2

D3

J8 M1 M9

F7 F2

P9

F8

T1

H3 H8 G2 H7

VSSQ_2

DQU1

VSSQ_3

DQU2

VSSQ_4

DQU3

VSSQ_5

DQU4

VSSQ_6

DQU5

VSSQ_7

DQU6

VSSQ_8

DQU7

VSSQ_9

B9

DML

VSS_4

DMU

VSS_5 VSS_6

DQL0

VSS_7

DQL1

VSS_8

DQL2

VSS_9

DQL3

VSS_10

DQL4

VSS_11

DQL5

VSS_12

D1

C3

D8

C8

E2

C2

E8

A7

F9

A2

G1

B8

G9

A3

VDD_3

A12

VDD_4

NC_6

VDD_5

NC_5

VDD_7

BA0

VDD_9

VDD_6 VDD_8

A-MA10

A-MA11

A-MA11

A-MA12

A-MA12

A-MA13

A-MA13 A-MA14

C16 C13 A15 E11 B13

B_DDR3_A[5]

A_DDR3_A[6]

B_DDR3_A[6]

A_DDR3_A[7]

B_DDR3_A[7]

A_DDR3_A[8]

B_DDR3_A[8]

A_DDR3_A[9]

B_DDR3_A[9]

A_DDR3_A[10]

B_DDR3_A[10]

A_DDR3_A[11]

B_DDR3_A[11]

A_DDR3_A[12]

B_DDR3_A[12]

A_DDR3_A[13]

B_DDR3_A[13]

A_DDR3_A[14]

B_DDR3_A[14]

A_DDR3_BA[0]

B_DDR3_BA[0]

A_DDR3_BA[1]

B_DDR3_BA[1]

A_DDR3_BA[2]

B_DDR3_BA[2]

E24 F21 E23 D22 D24 D21 C24 C25 F23 E21 D23

A-MBA0 A-MBA1 A-MBA2

A-MCK

A-MBA0 A-MBA1

C1209 0.01uF 50V

A-MCKE

A-MBA2 A-MCK A-MCKB A-MCKE

F13 B15 E13

G20

C17 A17 B16

F24 F20 G25

A_DDR3_MCLK

B_DDR3_MCLK

A_DDR3_MCLKZ

B_DDR3_MCLKZ

A_DDR3_MCLKE

B_DDR3_MCLKE

G23 F25

A-MCKB A-MODT A-MRASB

+1.5V_DDR

A-MCASB R1231 A-MWEB 10K A-MRESETB

A-MODT A-MRASB A-MCASB A-MWEB A-MRESETB

E14 B12 A12 C12

D20 A_DDR3_ODT

B_DDR3_ODT

A_DDR3_RASZ

B_DDR3_RASZ

A_DDR3_CASZ

B_DDR3_CASZ

A_DDR3_WEZ

B25 B24 A24

B_DDR3_WEZ

F11

E20 A_DDR3_RESET

B_DDR3_RESET

DQL0

VSS_8

DQL1

VSS_9

DQL2

VSS_10

DQL3

VSS_11

DQL4

VSS_12

DQL5

F7 F2 F8 H3 H8 G2 H7

DQL7 VSSQ_1

D7

VSSQ_2

DQU0

VSSQ_3

DQU1

VSSQ_4

DQU2

VSSQ_5

DQU3

VSSQ_6

DQU4

VSSQ_7

DQU5

VSSQ_8

DQU6

VSSQ_9

DQU7

C3 C8 C2 A7 A2 B8 A3

A-MDQSL A-MDQSLB A-MDQSU A-MDQSUB

A-MDQSL A-MDQSLB A-MDQSU A-MDQSUB

A-MDML

A-MDML

A-MDMU

A-MDMU

A-MDQL0 A-MDQL1

A-MDQL0 A-MDQL1

A-MDQL2

A-MDQL2

A-MDQL3

A-MDQL3

A-MDQL4

A-MDQL4

A-MDQL5

A-MDQL5

A-MDQL6

A-MDQL6

A-MDQL7

A-MDQL7

A-MDQU0

A-MDQU0

A-MDQU1

A-MDQU1

A-MDQU2

A-MDQU2

A-MDQU3

A-MDQU3

A-MDQU4

A-MDQU4

A-MDQU5

A-MDQU5

A-MDQU6

A-MDQU6

A-MDQU7

A-MDQU7

B19 C18

K24 A_DDR3_DQSL A_DDR3_DQSLB

B_DDR3_DQSL

B18 A18

J21 A_DDR3_DQSU A_DDR3_DQSUB

B_DDR3_DQSU

H24 A_DDR3_DQML

B_DDR3_DQML

A_DDR3_DQMU

B_DDR3_DQMU

D17 G15 B21 F15 B22 F14 A22 D15

F16 C21 E16 A20 D16 C20

L20 L23

A_DDR3_DQL[0]

B_DDR3_DQL[0]

A_DDR3_DQL[1]

B_DDR3_DQL[1]

A_DDR3_DQL[2]

B_DDR3_DQL[2]

A_DDR3_DQL[3]

B_DDR3_DQL[3]

A_DDR3_DQL[4]

B_DDR3_DQL[4]

A_DDR3_DQL[5]

B_DDR3_DQL[5]

A_DDR3_DQL[6]

B_DDR3_DQL[6]

A_DDR3_DQL[7]

B_DDR3_DQL[7]

A_DDR3_DQU[0]

B_DDR3_DQU[0]

A_DDR3_DQU[1]

B_DDR3_DQU[1]

A_DDR3_DQU[2]

B_DDR3_DQU[2]

A_DDR3_DQU[3]

B_DDR3_DQU[3]

A_DDR3_DQU[4]

B_DDR3_DQU[4]

A_DDR3_DQU[5]

B_DDR3_DQU[5]

A_DDR3_DQU[6]

B_DDR3_DQU[6]

A_DDR3_DQU[7]

B_DDR3_DQU[7]

G16 B20

J20

B_DDR3_DQSUB

E15 A21

K25

B_DDR3_DQSLB

J24 L24 J23 M24 H23 M23 K23 G21 L22 H22 K20 H20 L21 H21 K21

D9 G7 K2 K8 N1 N9 R1 R9

BA1 A1 VDDQ_1 CK

VDDQ_2

CK

VDDQ_3 VDDQ_4 VDDQ_5

CS

VDDQ_6

ODT

VDDQ_7

RAS

VDDQ_8

CAS

VDDQ_9

NC_2 NC_4

F3 DQSL

A8 C1 C9 D2 E9 F1 H2 H9 J1

NC_1 NC_3

A9

C7 B7

G8

E7

J2

D3

J8 M1

J9 L1 L9 T7

NC_7

M9

F7 F2

P9

F8

T1

H3 H8 G2

VSSQ_2

DQU1

VSSQ_3

DQU2

VSSQ_4

DQU3

VSSQ_5

DQU4

VSSQ_6

DQU5

VSSQ_7

DQU6

VSSQ_8

DQU7

VSSQ_9

B9

VSS_2

DML

VSS_4

DMU

VSS_5 VSS_6

DQL0

VSS_7

DQL1

VSS_8

DQL2

VSS_9

DQL3

VSS_10

DQL4

VSS_11

DQL5

VSS_12

D1

C3 C8

E2

C2

E8

A7

F9

A2

G1

B8

G9

A3

E1 G8 J2 J8 M1 M9 P1 P9 T1 T9

B1 VSSQ_1

D7

D8

B3

DQL6 DQL7

B1 VSSQ_1

DQU0

VSS_1 VSS_3

E3

P1

T9

A9 DQSU DQSU

E1

H7

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

VDD_1 VDD_2

A11

RESET

B3

DQL6

D7

A-MA10

D12

A_DDR3_A[5]

G22

DQSL

VSS_2

DQL7

B1 VSSQ_1

DQU0

A-MA9

B14

B_DDR3_A[4]

F22

B2

A9

T2

G3

A-MA9

D11

A_DDR3_A[4]

D25

L8

A10/AP

L9 T7

NC_6

VSS_1 VSS_3

E3

P1

T9

DQSU DQSU

E1

A-MA8

A14

B_DDR3_A[3]

ZQ

WE

L1

A-MA7

A-MA8

E12

B_DDR3_A[2]

A_DDR3_A[3]

A7

L2

F1 H2

A-MA7

C15

A_DDR3_A[2]

B23

H1

A8

CKE

D2 E9

A-MA5 A-MA6

F12

S7LR-M_NON_MS10 A_DDR3_A[0] SYMBOL.B B_DDR3_A[0] A_DDR3_A[1] B_DDR3_A[1]

VREFDQ

A5 A6

J7

J1 NC_1

F3

A8

A3

G9

A-MA5 A-MA6

B11

A4

BA2

A1 VDDQ_1

CK

A2

M2 N8

VREFCA

A1

M7

R1

M3

NC_3

G3

B2 D9

BA1

RESET

B3

DQL6

D7

VDD_1 VDD_2

A11

DQSL

VSS_2

DQL7

B1 VSSQ_1

DQU0

T8

A9 A10/AP

T2

R8 R2

A7

L9 T7

NC_6

VSS_1 VSS_3

E3

P1

T9

DQSU DQSU

E1

L8

WE

L1

P8

ZQ

A8

L2

F1 H2

N2 P2

A5

CKE

D2

J9

P3 H1 VREFDQ

A6

J7

C9 E9

A3

F9 M8

A0

E8 G1

N3 P7

A4

BA2

J1 NC_1

F3

A8

VREFCA

A2

M2 N8

A1 VDDQ_1

CK

M8 A0 A1

M7

R1

M3

NC_3

G3

B2 D9

BA1

RESET

B3

DQL6

D7

T8

A9 A10/AP

T2

R8 R2

DQSL

VSS_2

DQL7

B1 VSSQ_1

DQU0

L8

A7

L9 T7

P8

ZQ

WE

L1

N2 P2

A8

L2

F1 H2

J9

P3 H1 VREFDQ

A5 A6

CKE

D2 E9

A3

J7

C9

NC_5

VSS_1 VSS_3

E3

P1

T9

DQSU DQSU

E1

IC1201-*5 NT5CB64M16DP-DH

N3 P7

A4

BA2

J1 NC_1

F3

A8

VREFCA

A2

M2 N8

A1 VDDQ_1

CK

M8 A0 A1

M7

R1

M3

NC_3

G3

B2 D9

BA1

RESET

B3

DQL6 DQL7

D7

VDD_4

A13

DQSL

VSS_2

DMU E3

VDD_3

A12/BC

L9 T7

NC_6

VSS_1 VSS_3

E7 D3

VDD_1 VDD_2

A11

T2

L1

R8 R2 T8

A9 A10/AP

WE

DQSL C7 B7

L8

A7

L2

F1 H2

P8

ZQ

A8

CKE

D2

N2 P2

A5 A6

J7

C9 E9

P3 H1 VREFDQ

BA2

J1 NC_1

T2

A8

A3

N3 P7

A4

M2 N8

VREFCA

A2

M7

R1

A1 VDDQ_1 VDDQ_2

WE

G3

R3 L7

G7 K2

M3

CK CKE

K1 J3

B2 D9

BA1

L2

R8 R2

A7

BA2

K9

P8

ZQ

A8

J7

N2 P2

A5 A6

M2 M3

H1 VREFDQ

A4

M8 A0 A1

DDR_1600_1G_NANYA

IC1201-*4 K4B1G1646G-BCK0

EAN61829003

N3 P7 P3

A2

M7

N8

VREFCA

A1

DDR_1600_1G_SS

D3 E3

VSS_7

B1 D1

B7 E7

DQL6

B9

A-MA4

C14

NC_3

DQSL

E1

A-MA4

L2

VDDQ_6

NC_6

B3

A-MA3

K7

CKE

VDDQ_5

NC_2

A-MA2

A-MA3

J7

VDDQ_2

J1 J9

P2

A-MA2

A11

NC_5

BA1

A8

P8

A-MA0 A-MA1

M7

VDD_8

A1

A-MA14

A6

N2

A-MA0 A-MA1

1%

VREFDQ

P3

1%

H1

A-MVREFDQ

P7

R1235 56

VREFCA

R1236 56

A-MVREFCA

DQU0

VSSQ_2

DQU1

VSSQ_3

DQU2

VSSQ_4

DQU3

VSSQ_5

DQU4

VSSQ_6

DQU5

VSSQ_7

DQU6

VSSQ_8

DQU7

VSSQ_9

B9 D1 D8 E2 E8 F9 G1 G9

NC4_S7LRM M1_DDR (1DDR)

2012/06/21 54

LGE Internal Use Only


Serial Flash for SPI boot_NON_OS

+3.5V_ST

+3.5V_ST

OPT R5503 4.7K +3.5V_ST

SFLASH_NON_OS_WINBOND IC1300 W25Q64FVSSIG CS

/SPI_CS OPT R5501 10K SPI_SDO R5502 0

WP[IO2]

/FLASH_WP GND

SFLASH_NON_OS_MX

CS

SO/SIO1

WP

GND

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

8

0.1uF

VCC

1

8

2

7

3

6

4

5

2

7

3

6

4

5

%HOLD[IO3]

CLK SPI_SCK DI[IO0]

VCC

CS

DO[IO1]

SCLK

%WP[IO2]

SI/SIO0

SFLASH_OS_MACRONIX

IC1300-*2 W25Q80BVSSIG

HOLD

GND

1

8

2

7

3

6

4

5

R5504 33 SPI_SDI

SFLASH_OS_WINBOND

IC1300-*1 MX25L6406EM2I-12G

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

1

C5501 DO[IO1]

IC1300-*3 MX25L8006EM2I-12G VCC

HOLD[IO3]

CS#

SO/SIO1

CLK

WP#

DI[IO0]

GND

1

8

2

7

3

6

4

5

VCC

HOLD#

SCLK

SI/SIO0

NC4_S7LRM S_FLASH_NON_OS

2012.06.21 55

LGE Internal Use Only


LVDS (EU)

[51Pin LVDS Connector] (For FHD 60Hz)

FOR FHD REVERSE(10bit)

[30Pin LVDS Connector] (For HD 60Hz_Normal)

Change in S7LR

HD

FHD

MIRROR

P1100

Pol-change

P1101 FF10001-30

FI-RE51S-HF-J-R1500 RXA4+

RXA0+

RXA0-

RXA4-

RXA0-

RXA0+

RXA3+

RXA1+

RXA1-

RXA3-

RXA1-

RXA1+

RXACK+

RXA2+

RXA2-

RXACK-

RXA2-

RXA2+

RXA2+

RXACK+

RXACK-

1

1

2

2 LVDS_SEL

3

3 +3.3V_Normal

4

4 5

5 OPT R1100 3.3K

6

RXA2-

RXACK-

RXACK+

RXA1+

RXA3+

RXA3-

RXA1-

RXA3-

RXA3+

RXA0+

RXA4+

RXA4-

RXA0-

RXA4-

RXA4+

7 OPT R1101 10K

8 9

6

RXA3+

7

RXA3-

8

10

9

RXACK+

10

RXACK-

11

11 12

RXA4+

13

RXA4-

14

RXA3+

15

RXA3-

16

RXACK+

17

RXACK-

18 19

RXA2+

20

RXA2-

12

RXA2+

RXB4+

RXB0+

RXB0-

13

RXA2-

RXB4-

RXB0-

RXB0+

14

RXB3+

RXB1+

RXB1-

15

RXA1+

RXB3-

RXB1-

RXB1+

16

RXA1-

RXBCK+

RXB2+

RXB2-

17

RXB2-

RXB2+

18

RXA0+

RXB2+

RXBCK+

RXBCK-

19

RXA0-

RXB2-

RXBCK-

RXBCK+

20

21

RXB1+

RXB3+

RXB3-

21

22

RXA1+

RXB1-

RXB3-

RXB3+

22

23

RXA1-

RXB0+

RXB4+

RXB4-

23

RXB0-

RXB4-

RXB4+

24

24

RXA0+

25

RXA0-

+3.3V_Normal

OPT R1103 3.3K PANEL_VCC OPT R1104 10K HD_BEAD_SAMSUNG L1101 120 CIS21J121

25 R1105

26

LVDS_SEL

RXBCK-

0

26

NON_AUO/NON_HD 27

27 28

RXB4+

28

29

RXB4-

29

30

RXB3+

31

RXB3-

32

RXBCK+

33

RXBCK-

FOR FHD REVERSE(8bit)

MIRROR

36

HD C1101 0.1uF 16V

30 31

Change in S7LR

34 35

HD_BEAD_CSG L1101-*1 UBW2012-121F

Pol-change

Shift

RXA4+

RXA4+

RXA4-

RXA0-

RXA4-

RXA4-

RXA4+

RXA0+ RXA1-

RXB2+ RXB2RXA3+

RXA0+

RXA0-

RXA3-

RXA0-

RXA0+

RXA1+

RXACK+

RXA1+

RXA1-

RXA2-

RXACK-

RXA1-

RXA1+

RXA2+

RXA2+

RXA2+

RXA2-

RXACKRXACK+

37 38

RXB1+

39

RXB1-

40

RXB0+

41

RXB0-

42

R1106

43

NON_AUO/NON_HD R1107 0

0

RXA2-

RXA2-

RXA2+

RXA1+

RXACK+

RXACK-

RXA3-

RXA1-

RXACK-

RXACK+

RXA3+

RXA0+

RXA3+

RXA3-

RXA4-

RXA0-

RXA3-

RXA3+

RXA4+

RXB4+

RXB4+

RXB4-

RXB0-

RXB4-

RXB4-

RXB4+

RXB0+

RXB3+

RXB0+

RXB0-

RXB1-

RXB3-

RXB0-

RXB0+

RXB1+

PANEL_VCC

NON_AUO/NON_HD 44 45 46 47

FHD_BEAD_SAMSUNG L1100 120 CIS21J121

48 49 50 51

FHD C1100 0.1uF 16V

FHD_BEAD_CSG L1100-*1 UBW2012-121F

RXBCK+

RXB1+

RXB1-

RXB2-

RXBCK-

RXB1-

RXB1+

RXB2+

EU pin assign is different from NON EU. Because of position of HD wafer.

52

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

RXB2+

RXB2+

RXB2-

RXBCK-

RXB2-

RXB2-

RXB2+

RXBCK+

RXB1+

RXBCK+

RXBCK-

RXB3-

RXB1-

RXBCK-

RXBCK+

RXB3+

RXB0+

RXB3+

RXB3-

RXB4-

RXB0-

RXB3-

RXB3+

RXB4+

NC4_S7LRM LVDS_EU

2013/01/24 57

LGE Internal Use Only



Contents of LCD TV Standard Repair Process Detail Technical Manual No.

Error symptom

1

Content

Page

Check LCD back light with naked eye

A1

LED driver B+ measuring method

A2

Check White Balance value

A3

Power Board voltage measuring method

A4

TUNER input signal strength checking method

A5

LCD-TV Version checking method

A6

LCD TV connection diagram

A7

Check Link Cable (LVDS) reconnection condition

A8 A9

12

Adjustment Test pattern - ADJ Key

A10

13

LCD TV connection diagram

A8

Check Link Cable (LVDS) reconnection condition

A8 A9

15

Adjustment Test pattern - ADJ Key

A10

16

Exchange T-Con Board (1)

A-1/5

17

Exchange T-Con Board (2)

A-2/5

Exchange LED driver Board (PSU)

A-3/5

19

Exchange Module itself (1)

A-4/5

20

Exchange Module itself (2)

A-5/5

2 3

A. Video error_ No video/Normal audio

4 6 7

A. Video error_ No video/Video lag/stop

9 10 11

14

18

A. Video error_Color error

A. Video error_Vertical/Horizontal bar, residual image, light spot

<Appendix> Defected Type caused by T-Con/ Inverter/ Module

Remarks

Continue to the next page 1 Copyright Š 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only


Standard Repair Process

Error symptom

LCD TV

A. Video error

Established date

No video/ Normal audio

Revised date

2013. 01 .09

1/14

First of all, Check whether all of cables between board is inserted properly or not. (Main B/D↔ Power B/D, LVDS Cable,Speaker Cable,IR B/D Cable,,,) ☞A1 No video Normal audio

Normal audio

Y

Check Back Light On with naked eye

N Move to No video/No audio

☞A4 Y

On

Check Power Board 24v, 12v,3.5v etc.

N

☞A2

Y

Replace T-con Board or module

N

Check Power Board 93.2~118.5V v output

Normal voltage

Normal voltage

Y

Repair Power Board or parts

Replace Inverter or module

End

N Repair Power Board or parts

※Precaution

☞A6 & A3

Always check & record S/W Version and White Balance value before replacing the Main Board

Replace Main Board

Re-enter White Balance value

2 Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only


Standard Repair Process

LCD TV

Error symptom

A. Video error

Established date

No video/ No audio

Revised date

2013. 01 .09

2/14

☞A4 No Video/ No audio

Check various voltages of Power Board ( 3.5V,12V,20V or 24V…)

Normal voltage?

Y

N

Check and replace MAIN B/D End

Replace Power Board and repair parts

3 Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only


Standard Repair Process

Error symptom

LCD TV

☞ A5 Check RF Signal level

Normal Signal?

Y

A. Video error

Established date

Picture broken/ Freezing

Revised date

2013. 01 .09 3/14

. By using Digital signal level meter . By using Diagnostics menu on OSD ( Menu→ Set up→ Support → Signal Test ) - Signal strength (Normal : over 50%) - Signal Quality (Normal: over 50%)

Check whether other equipments have problem or not. (By connecting RF Cable at other equipment) → DVD Player ,Set-Top-Box, Different maker TV etc`

N

☞ A6

Check RF Cable Connection 1. Reconnection 2. Install Booster

Normal Picture?

Y

Check S/W Version

SVC Bulletin?

N

Y

N

Check Tuner soldering

Normal Picture?

Y

Close

N

S/W Upgrade Normal Picture?

N

Replace Main B/D

Contact with signal distributor or broadcaster (Cable or Air) Normal Picture?

Y

N

Y Close Close

4 Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only


Standard Repair Process

Error symptom

LCD TV ☞ A5 Check RF Signal level

Normal Signal?

Y

N

A. Video error

Established date

Tuning fail, Picture broken/ Freezing

Revised date

2013. 01 .09 4/14

Check RF signal cable (DVB satellite signal or not) Check whether other equipments have problem or not. (By connecting RF Cable at other equipment) → Set-Top-Box, Different maker TV etc

Check satellite setting. - Check LNB frequency. - Check satellite - Check Satellite connection (DiSEqC, motor, etc…)

☞ A6 Y

Normal setting?

Check S/W Version

N

SVC Bulletin?

Check Tuner soldering

Replace Main B/D

Y

N

S/W Upgrade Contact with signal distributor or broadcaster (Cable or Air)

Change satellite setting (match with installed ANT)

Normal Picture?

N

Y Normal Picture?

N Close

Close Y

Close

5 Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only


Standard Repair Process

LCD TV

Error symptom

☞A7

A. Video error

Established date

Color error

Revised date

2013. 01 .09 5/14

☞ A8/ A9

Check color by input -External Input -COMPONENT -RGB -HDMI/DVI

Color error?

Y

N

※ Check and replace Link Cable (LVDS) and contact condition

Y Color error?

Y

Color error?

Replace Main B/D

N

N

Check error color input mode

☞A10 Check Test pattern

Replace module

End

External Input/ Component error

Check external device and cable

External device Y /Cable normal

Replace Main B/D

N Request repair for external device/cable

N RGB/ HDMI/DVI error

Check external device and cable

External device Y /Cable normal

Replace Main B/D

6 Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only


Standard Repair Process

LCD TV

Established date

A. Video error

Error symptom

Vertical / Horizontal bar, residual image, light spot, external device color error

2013. 01 .09

Revised date

6/14

Vertical/Horizontal bar, residual image, light spot

Replace Module

☞A7 Check color condition by input -External Input -Component -HDMI

Screen Y normal?

☞ A8/ A9

Check external device connection condition

Y Normal?

Screen normal?

N

N

Check Test pattern

N

Replace Main B/D

Screen normal? Y

Y

Request repair for external device

Replace module

☞A10

Check and replace Link Cable

N

End

End

External device screen error-Color error Check S/W Version

Check version

N

Y

Check screen condition by input -External Input -Component -HDMI/DVI

External Input error Component error

S/W Upgrade

Connect other external device and cable

(Check normal operation of External Input, Component, and HDMI by connecting Jig, pattern Generator ,Set-top Box etc. Connect other external device and cable

Normal screen?

N

HDMI

Y

(Check normal operation of External Input, Component, and HDMI by connecting Jig, pattern Generator ,Set-top Box etc.

N Replace Main B/D

Screen normal? Y Request repair for external device Y Screen normal?

N

Replace Main B/D

End

7 Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only


Standard Repair Process

LCD TV

Error symptom

B. Power error

Established date

No power

Revised date

☞A11 Check Power LED

. Stand-By: Red

2013. 01 .09 7/14

☞A13 DC Power on by pressing Power Key On Remote control

Y

Power LED On? N

Normal operation?

N

Check Power On ‘”High”

OK?

Y

Replace Power B/D

Y

Check Power cord was inserted properly

Replace Main B/D

☞A4 N

Measure voltage of each output of Power B/D

Normal? Y

Y

※ Close

Check ST-BY 3.5V

Normal Y voltage?

☞A12

Normal voltage?

Y

Replace Main B/D

N Replace Power B/D

N

Replace Power B/D

8 Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only


Standard Repair Process

LCD TV

Established date

B. Power error

Error symptom

Off when on, off while viewing, power auto on/off

2013. 01 .09

Revised date

8/14

Check outlet

☞A14 Check A/C cord

Check for all 3- phase power out

Error?

N

Check Power Off Mode

CPU Abnormal

Replace Main B/D

Normal?

Y

End

N Y

☞A13

Fix A/C cord & Outlet and check each 3 phase out

(If Power Off mode is not displayed) Check Power B/D voltage ※ Caution Check and fix exterior of Power B/D Part

* Please refer to the all cases which can be displayed on power off mode.

Replace Power B/D

Abnormal 1

Normal voltage?

Y

Replace Main B/D

N Replace Power B/D

Status

Power off List "POWEROFF_REMOTEKEY" "POWEROFF_OFFTIMER" "POWEROFF_SLEEPTIMER" "POWEROFF_INSTOP" Normal "POWEROFF_AUTOOFF" "POWEROFF_ONTIMER" "POWEROFF_RS232C" "POWEROFF_SWDOWN" "POWEROFF_UNKNOWN" "POWEROFF_ABNORMAL1" Abnormal "POWEROFF_CPUABNORMAL"

Power Power Power Power Power Power Power Power Power Power Power

off off off off off off off off off off off

Explanation by REMOTE CONTROL by OFF TIMER by SLEEP TIMER by INSTOP KEY by AUTO OFF by ON TIMER by RS232C by S/W Download by unknown status except listed case by abnormal status except CPU trouble by CPU Abnormal

9 Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only


Standard Repair Process

LCD TV

Error symptom

C. Audio error

Established date

No audio/ Normal video

Revised date

☞A15 No audio Screen normal

Check user menu > Speaker off

2013. 01 .09 9/14

☞A16 N

Off

Check audio B+ 24V of Power Board

Normal voltage

Y

N

Cancel OFF

Check Speaker disconnection

Y

Replace Power Board and repair parts

Disconnection

N

Replace MAIN Board

End

Y Replace Speaker

10 Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only


Standard Repair Process

LCD TV

C. Audio error

Error symptom

Wrecked audio/ discontinuation/noise

Established date

2013. 01 .09

Revised date

10/14

→ abnormal audio/discontinuation/noise is same after “Check input signal” compared to No audio ☞A16

Check input signal -RF -External Input signal

Wrecked audio/ Discontinuation/ Noise for all audio Signal normal?

Check and replace speaker and connector

Check audio B+ Voltage (24V)

Y

Y Wrecked audio/ Discontinuation/ Noise only for D-TV

N

N

Wrecked audio/ Discontinuation/ Noise only for Analog (When RF signal is not received) Request repair to external cable/ANT provider (In case of External Input signal error) Check and fix external device

Normal voltage?

Replace Main B/D

Replace Power B/D

Replace Main B/D

Wrecked audio/ Discontinuation/ Noise only for External Input Connect and check other external device

Normal audio?

End

N

Y Check and fix external device

11 Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only


Standard Repair Process

Error symptom

LCD TV

D. Function error

Established date

Remote control & Local switch checking

Revised date

2013. 01 .09 11/14

1. Remote control(R/C) operating error ☞A17 Check R/C itself Operation

☞A17

Check & Repair Cable connection Connector solder

Normal Y operating? N

Normal operating?

N

Y

Check R/C Operating When turn off light in room

Check & Replace Baterry of R/C

If R/C operate, Explain the customer cause is interference from light in room.

Normal operating?

Replace Main B/D

☞A17

Check B+ 3.5V On Main B/D

☞A4

Close

Normal Voltage?

Y

Check IR Output signal

N

Check 3.5v on Power B/D Replace Power B/D or Replace Main B/D (Power B/D don’t have problem)

Normal Signal?

Y

N Repair/Replace IR B/D

Close

N Replace R/C

12 Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only


Standard Repair Process

LCD TV

Check input signal

Signal input?

Established date

D. Function error

Error symptom

External device recognition error

Y

N

Check and fix external device/cable

Check technical information - Fix information - S/W Version

Technical information?

2013. 01 .09

Revised date

N

External Input and Component Recognition error

12/14

Replace Main B/D

Y

Fix in accordance with technical information

RGB,HDMI/ DVI, Optical Recognition error

Replace Main B/D

13 Copyright Š 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only


Standard Repair Process

LCD TV

Identify nose type

Error symptom

Circuit noise

Mechanical noise

E. Noise

Established date

Circuit noise, mechanical noise

Revised date

Check location of noise

2013. 01 .09 13/14

Replace PSU(with LED driver) OR

Replace LED driver

Check location of noise

※ When the nose is severe, replace the module (For models with fix information, upgrade the S/W or provide the description)

※ Mechanical noise is a natural phenomenon, and apply the 1st level description. When the customer does not agree, apply the process by stage. ※ Describe the basis of the description in “Part related to nose” in the Owner’s Manual.

OR

※ If there is a “Tak Tak” noise from the cabinet, refer to the KMS fix information and then proceed as shown in the solution manual (For models without any fix information, provide the description)

14 Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only


Standard Repair Process

LCD TV

F. Exterior defect

Error symptom

Zoom part with exterior damage

Exterior defect

Revised date

Module damage

Replace module

Cabinet damage

Replace cabinet

Remote controller damage

Stand dent

Established date

2013. 01 .09 14/14

Replace remote controller

Replace stand

15 Copyright Š 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only


Contents of LCD TV Standard Repair Process Detail Technical Manual Continued from previous page No.

Error symptom

Content

Page

21

Check front display LED

A11

22

Check power input Voltage & ST-BY 3.5V

A12

Checking method when power is ON

A13

POWER BOARD voltage measuring method

A4

POWER OFF MODE checking method

A14

Checking method in menu when there is no audio

A15

Voltage and speaker checking method when there is no audio

A16

23

B. Power error_No power

24

Remarks

25 26

B. Power error_Off when on, off while viewing

28 C. Audio error_No audio/Normal video 29 30

C. Audio error_Wrecked audio/discontinuation

Voltage and speaker checking method in case of audio error

A16

31

D. Function error_ No response in remote controller, key error

Remote controller operation checking method

A17

16 Copyright Š 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only


Standard Repair Process Detail Technical Manual LCD TV

Error symptom Content

A. Video error_No video/Normal audio Check Back Light On with naked eye

Established date Revised date

2013. 01 .09 A1

<ALL MODELS>

Power On -> disjoint back case -> check lighting at 2 points.

17 Copyright Š 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only


Standard Repair Process Detail Technical Manual LCD TV

Error symptom Content

A. Video error_No video/Normal audio Inverter B+ 24V measuring method

Established date Revised date

2013. 01 .09 A2

<ALL MODELS>

Measure DC 93.2~118.5V applying to Module from Power Board. Output 93.2~118.5V from Power Board -> supply to Module. Check Pin contacting statement and connection statement.

18 Copyright Š 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only


Standard Repair Process Detail Technical Manual LCD TV

Error symptom

A. Video error_No video/Normal audio

Content

Check White Balance value

Established date Revised date

2013. 01 .09 A3

<ALL MODELS>

Entry Entry method method 1. Press Press the the ADJ ADJ button button on on the the remote remote controller controller for for adjustment. adjustment. 1. 2. Enter Enter into into White White Balance Balance of of item item 7. 6. 2. 3. 3. After After recording recording the the R, R, G, G, B B (GAIN, (GAIN, Cut) Cut) value value of of Color Color Temp Temp (Cool/Medium/Warm), (Cool/Medium/Warm), rereenter the the value value after after replacing replacing the the MAIN MAIN BOARD. BOARD. enter

19 Copyright Š 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only


Standard Repair Process Detail Technical Manual LCD TV

Error symptom

A. Video error_No video/ Audio

Content

Power Board voltage measuring method

Established date Revised date

2013. 01 .09 A4

Edge LED Check the DC 24V, 12V, 3.5V. 18 Pin (Power Board ↔ Main Board) - Common

1

Power on

2

DRV ON

3

3.5V

4

PDIM#1

5

3.5V

6

PDIM#2

7

GND

8

GND

9

24V

10

24V

11

GND

12

GND

13

12V

14

12V

15

12V

16

N.C

17

GND

18

GND

20 Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only


Standard Repair Process Detail Technical Manual LCD TV

Error symptom

A. Video error_Video error, video lag/stop

Content

TUNER input signal strength checking method

Established date Revised date

2013. 01 .09 A5

<ALL MODELS>

MENU => Press red key Remote controller=>signal test => Select channel

When the signal is strong, use the attenuator (-10dB, -15dB, -20dB etc.)

21 Copyright Š 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only


Standard Repair Process Detail Technical Manual LCD TV

Error symptom Content

<ALL MODELS>

A. Video error_Video error, video lag/stop LCD-TV Version checking method

Established date Revised date

2013. 01 .09 A6

1. Checking method for remote controller for adjustment

Version

Press the IN-START with the remote controller for adjustment

22 Copyright Š 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only


Standard Repair Process Detail Technical Manual LCD TV

Error symptom Content

A. Video error _Vertical/Horizontal bar, residual image, light spot LCD TV connection diagram (1)

Established date Revised date

2013. 01 .09 A7

<ALL MODELS>

As the part connecting to the external input(AV, COMP, HDMI), check the screen condition by signal 23 Copyright Š 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only


Standard Repair Process Detail Technical Manual LCD TV

Error symptom Content

A. Video error_Color error Check and replace Link Cable(LVDS) and contact condition

Established date Revised date

2013. 01 .09 A8/A9

<ALL MODELS>

1. Check and replace LVDS Cable 2. Check LVDS connection condition

24 Copyright Š 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only


Standard Repair Process Detail Technical Manual LCD TV

Error symptom

A. Video error_Color error

Content

Adjustment Test pattern - ADJ Key

Established date Revised date

2013. 01 .09 A10

You can view 6 types of patterns using the ADJ Key Checking item : 1. Defective pixel 2. Residual image 3. MODULE error (ADD-BAR,SCAN BAR..) 4.Video error (Classification of MODULE or Main-B/D!) 25 Copyright Š 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only


Appendix : Exchange T-Con Board (1)

Solder defect, CNT Broken

Solder defect, CNT Broken

Solder defect, CNT Broken

Solder defect, CNT Broken

T-Con T-Con Defect, Defect, CNT CNT Broken Broken Solder defect, CNT Broken T-Con Defect, CNT Broken

Abnormal Power Section

Solder defect, Short/Crack

Abnormal Power Section

Solder defect, Short/Crack

26 Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only


Appendix : Exchange T-Con Board (2)

Abnormal Power Section

Solder defect, Short/Crack

GRADATION

Abnormal Power Section

Solder defect, Short/Crack

Fuse Open, Abnormal power section

Abnormal Display

Noise

GRADATION

27 Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only


Appendix : Exchange PSU(LED driver)

No Light

Dim Light

Dim Light

Dim Light

No picture/Sound Ok 28 Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only


Appendix : Exchange the Module (1)

Panel Mura, Light leakage

Crosstalk

Panel Mura, Light leakage

Press damage

Press damage

Crosstalk

Un-repairable Cases In this case please exchange the module.

Press damage 29 Copyright Š 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only


Appendix : Exchange the Module (2)

Vertical Block Source TAB IC Defect

Horizontal Block Gate TAB IC Defect

Vertical Line Source TAB IC Defect

Horizontal Block Gate TAB IC Defect Gate TAB IC Defect

Vertical Block Source TAB IC Defect

Horizontal line Gate TAB IC Defect Gate TAB IC Defect

Un-repairable Cases In this case please exchange the module. Horizontal Block Gate TAB IC Defect Gate TAB IC Defect 30 Copyright Š 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only


Standard Repair Process Detail Technical Manual LCD TV

Error symptom

B. Power error _No power

Content

Check front display LED

Established date Revised date

2013. 01 .09 A11

Front LED control : Menu  Option  Standby light ON

ST-BY condition: Red

31 Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only


Standard Repair Process Detail Technical Manual LCD TV

Error symptom

B. Power error _No power

Content

Check power input voltage and ST-BY 3.5V

Established date Revised date

2013. 01 .09 A12

Edge LED Check the DC 24V, 12V, 3.5V. 18 Pin (Power Board ↔ Main Board) - Common

1

Power on

2

DRV ON

3

3.5V

4

PDIM#1

5

3.5V

6

PDIM#2

7

GND

8

GND

9

24V

10

24V

11

GND

12

GND

13

12V

14

12V

15

12V

16

N.C

17

GND

18

GND

32 Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only


Standard Repair Process Detail Technical Manual LCD TV

Error symptom

B. Power error _No power

Content

Checking method when power is ON

Established date Revised date

2013. 01 .09 A13

Edge LED Check the DC 24V, 12V, 3.5V. 18 Pin (Power Board ↔ Main Board) - Common

1

Power on

2

DRV ON

3

3.5V

4

PDIM#1

5

3.5V

6

PDIM#2

7

GND

8

GND

9

24V

10

24V

11

GND

12

GND

13

12V

14

12V

15

12V

16

N.C

17

GND

18

GND

33 Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only


Standard Repair Process Detail Technical Manual LCD TV

Error symptom Content

B. Power error _Off when on, off whiling viewing POWER OFF MODE checking method

Established date Revised date

2013. 01 .09 A14

<ALL MODELS>

Entry method 1. Press the IN-START button of the remote controller for adjustment 2. Check the entry into adjustment item 3 34 Copyright Š 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only


Standard Repair Process Detail Technical Manual Error symptom

LCD TV

Content

C. Audio error_No audio/Normal video Checking method in menu when there is no audio

Established date Revised date

2013. 01 .09 A15

<ALL MODELS>

Checking method 1. Press the MENU button on the remote controller 2. Select the AUDIO function of the Menu 3. Select Sound Out – TV Speaker *If you set Sound-Out menu as External Speaker/LG Sound Sync, TV Speaker will not work.

35 Copyright Š 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only


Standard Repair Process Detail Technical Manual LCD TV

Error symptom

C. Audio error_No audio/Normal video

Content

Voltage and speaker checking method when there is no audio

<ALL MODELS>

Established date Revised date

Check the DC 24V, 12V, 3.5V.

2013. 01 .09 A16

18②Pin (Power Board ↔ Main Board) - Common

1

Power on

2

DRV ON

3

3.5V

4

PDIM#1

5

3.5V

6

PDIM#2

7

GND

8

GND

9

24V

10

24V

11

GND

12

GND

13

12V

14

12V

15

12V

16

N.C

17

GND

18

GND

③ Checking order when there is no audio ① Check the contact condition of or 24V connector of Main Board ② Measure the 24V input voltage supplied from Power Board (If there is no input voltage, remove and check the connector) ③ Connect the tester RX1 to the speaker terminal and if you hear the Chik Chik sound when you touch the GND and output terminal, the speaker is normal. 36 Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only


Standard Repair Process Detail Technical Manual LCD TV

Error symptom

D. Function error_ No response in remote controller, key error

Content

Remote controller operation checking method

Established date Revised date

2013. 01 .09 A17

<ALL MODELS>

② P600

③ ①

1 2 3 4 5 6 7 8 9

GND KEY1 KEY2 3.5V_ST GND LED_R/BUZZ IR GND GND

Checking order 1, 2. Check IR cable condition between IR & Main board. 3. Check the st-by 3.5V on the terminal 4. 4. When checking the Pre-Amp when the power is in ON condition, it is normal when the Analog Tester needle moves slowly, and defective when it does not move at all.

37 Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only


Turn static files into dynamic content formats.

Create a flipbook
Issuu converts static files into: digital portfolios, online yearbooks, online catalogs, digital photo albums and more. Sign up and create your flipbook.