Mnual de serviço televisor PHILIPS modelo 32PFL1508/F7, 32PFL3508/F7 e 32PFL3508/F8 chassis PL13.8. by Portal da Eletrônica

32â&#x20AC;? LCD TV chassis PL13.8

Service Manual Contents TYPE A 32PFL3508/F7

PHILIPS

(Serial No.: ME1)

32PFL3508/F8

PHILIPS

(Serial No.: XA1, XA2)

32PFL1508/F8

PHILIPS

(Serial No.: XA1)

PHILIPS

(Serial No.: DS1)

TYPE B 32PFL1508/F8

Thisservice service manual contains information of different types of types models.of models. This manual contains information of different Makesure sure to thethe section describing your model. Make torefer refertoto section describing yourTmodel. ÂŠ 2013 Funai Electric Co., Ltd. All rights reserved. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed, downloaded or stored in any storage medium, in any form or for any purpose without the express prior written consent of Funai. Furthermore, any unauthorized commercial distribution of this manual or any revision hereto is strictly prohibited. Information in this document is subject to change without notice. Funai reserves the right to change the content herein without the obligation to notify any person or organization of such changes. with the design is a registered trademark of Funai Electric Co., Ltd and may not be used in any way without the express written consent of Funai. All other trademarks used herein remain the exclusive property of their respective owners. Nothing contained in this manual should be construed as granting, by implication or otherwise, any license or right to use any of the trademarks displayed herein. Misuse of any trademarks or any other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property rights to the fullest extent of the law. 130926

IMPORTANT SAFETY NOTICE Proper service and repair is important to the safe, reliable operation of all P&F Equipment. The service procedures recommended by P&F and described in this service manual are effective methods of performing service operations. Some of these service special tools should be used when and as recommended. It is important to note that this service manual contains various CAUTIONS and NOTICES which should be carefully read in order to minimize the risk of personal injury to service personnel. The possibility exists that improper service methods may damage the equipment. It also is important to understand that these CAUTIONS and NOTICES ARE NOT EXHAUSTIVE. P&F could not possibly know, evaluate and advice the service trade of all conceivable ways in which service might be done or of the possible hazardous consequences of each way. Consequently, P&F has not undertaken any such broad evaluation. Accordingly, a servicer who uses a service procedure or tool which is not recommended by P&F must first use all precautions thoroughly so that neither his safety nor the safe operation of the equipment will be jeopardized by the service method selected.

The LCD panel is manufactured to provide many years of useful life. Occasionally a few non active pixels may appear as a tiny spec of color. This is not to be considered a defect in the LCD screen.

TABLE OF CONTENTS Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Important Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 Standard Notes for Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 Cabinet Disassembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 Electrical Adjustment Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 How to Initialize the LCD TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1 Firmware Renewal Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1 Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1 Block Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1 Schematic Diagrams / CBA and Test Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1 Wiring Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1 Exploded Views . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1 Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-1 Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-1

SPECIFICATIONS < TUNER / NTSC > Description

Condition

Unit

Nominal

Limit

---

MHz

±2.3

±2.1

TV.ch.4 CA.ch.31 CA.ch.87

dBμ dBμ dBμ

18 18 18

20 20 23

Condition

Unit

Nominal

Limit

---

kHz

---

±100

ch.4 ch.10 ch.41

dBm dBm dBm

-------

-76/0 -76/0 -76/+4

Description

Condition

Unit

Nominal

Limit

1. Native Pixel Resolution

Horizontal Vertical

pixels pixels

1366 768

-----

---

cd/m2

250 (TYPE A) 230 (TYPE B)

---

Horizontal Vertical

° °

-88 to 88 -88 to 88

-----

Condition

Unit

Nominal

Limit

Horizontal Vertical

% %

5 5

5±5 5±5

--x y

°K

12000 0.272 0.278

--±3% ±3%

1. AFT Pull-In Range 2. Synchronizing Sens.

< TUNER / ATSC > Description 1. Received Freq. Range (-28dBm) 2. ATSC Dynamic Range (min / max)

< LCD PANEL >

2. Brightness (w / filter) 3. Viewing Angle

< VIDEO > Description 1. Over Scan

2. Color Temperature

<Measurement Condition> Input signal: HDMI1 Raster (40/80IRE) 1080i@60 Measurement point: Screen Center Measuring instrument: Made of KONICA MINOLTA Luminance meter CA-310

Aging Time:

60min. (Retail MODE/100IRE Raster HDMI 1080i@60) MODE setting of TV: Shipment setting/Retail MODE Ambient temperature:25°C ± 5°C

3. Resolution (composite video)

Horizontal Vertical

line line

400 350

-----

< AUDIO > All items are measured across 8 Ω load at speaker output terminal with L.P.F. Description

Condition

Unit

Nominal

Limit

1. Audio MAX Output (ATSC 0dBfs)

Lch/Rch

8.0/8.0

7.0/7.0

500mW: Lch/Rch

0.5/0.5

2.0/2.0

-6dB: Lch -6dB: Rch

Hz Hz

70 to 10 k 70 to 10 k

100 to 8 k 100 to 8 k

2. Audio Distortion (NTSC) 3. Audio Freq. Response (NTSC)

1-1

PL13.9SP

IMPORTANT SAFETY PRECAUTIONS Prior to shipment from the factory, our products are strictly inspected for recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced.

Safety Precautions for LCD TV Circuit

d. Leakage Current Hot Check - With the instrument completely reassembled, plug the AC line cord directly into a 120 V AC outlet. (Do not use an isolation transformer during this test.) Use a leakage current tester or a metering system that complies with American National Standards Institute (ANSI) C101.1 Leakage Current for Appliances and Underwriters Laboratories (UL) 1410, (50.7). With the instrument AC switch first in the on position and then in the off position, measure from a known earth ground (metal water pipe, conduit, etc.) to all exposed metal parts of the instrument (antennas, handle brackets, metal cabinet, screw heads, metallic overlays, control shafts, etc.), especially any exposed metal parts that offer an electrical return path to the chassis. Any current measured must not exceed 0.5 milli-ampere. Reverse the instrument power cord plug in the outlet and repeat the test.

1. Before returning an instrument to the customer, always make a safety check of the entire instrument, including, but not limited to, the following items: a. Be sure that no built-in protective devices are defective and have been defeated during servicing. (1) Protective shields are provided on this chassis to protect both the technician and the customer. Correctly replace all missing protective shields, including any removed for servicing convenience. (2) When reinstalling the chassis and/or other assembly in the cabinet, be sure to put back in place all protective devices, including but not limited to, nonmetallic control knobs, insulating fishpapers, adjustment and compartment covers/shields, and isolation resistor/capacitor networks. Do not operate this instrument or permit it to be operated without all protective devices correctly installed and functioning. Servicers who defeat safety features or fail to perform safety checks may be liable for any resulting damage.

READING SHOULD NOT BE ABOVE 0.5 mA DEVICE BEING TESTED

b. Be sure that there are no cabinet openings through which an adult or child might be able to insert their fingers and contact a hazardous voltage. Such openings include, but are not limited to, (1) spacing between the Liquid Crystal Panel and the cabinet mask, (2) excessively wide cabinet ventilation slots, and (3) an improperly fitted and/or incorrectly secured cabinet back cover.

LEAKAGE CURRENT TESTER

TEST ALL EXPOSED METAL SURFACES

ALSO TEST WITH PLUG REVERSED USING AC ADAPTER PLUG AS REQUIRED

c. Antenna Cold Check - With the instrument AC plug removed from any AC source, connect an electrical jumper across the two AC plug prongs. Place the instrument AC switch in the on position. Connect one lead of an ohmmeter to the AC plug prongs tied together and touch the other ohmmeter lead in turn to each tuner antenna input exposed terminal screw and, if applicable, to the coaxial connector. If the measured resistance is less than 1.0 megohm or greater than 5.2 megohm, an abnormality exists that must be corrected before the instrument is returned to the customer. Repeat this test with the instrument AC switch in the off position.

EARTH GROUND

ANY MEASUREMENTS NOT WITHIN THE LIMITS SPECIFIED HEREIN INDICATE A POTENTIAL SHOCK HAZARD THAT MUST BE ELIMINATED BEFORE RETURNING THE INSTRUMENT TO THE CUSTOMER OR BEFORE CONNECTING THE ANTENNA OR ACCESSORIES. 2. Read and comply with all caution and safetyrelated notes on or inside the receiver cabinet, on the receiver chassis, or on the Liquid Crystal Panel.

2-1

LTVN_ISP

7. Product Safety Notice - Some electrical and mechanical parts have special safety-related characteristics which are often not evident from visual inspection, nor can the protection they give necessarily be obtained by replacing them with components rated for higher voltage, wattage, etc. Parts that have special safety characteristics are identified by a # on schematics and in parts lists. Use of a substitute replacement that does not have the same safety characteristics as the recommended replacement part might create shock, fire, and/or other hazards. The product's safety is under review continuously and new instructions are issued whenever appropriate. Prior to shipment from the factory, our products are strictly inspected to confirm they comply with the recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced.

3. Design Alteration Warning - Do not alter or add to the mechanical or electrical design of this TV receiver. Design alterations and additions, including, but not limited to circuit modifications and the addition of items such as auxiliary audio and/or video output connections, might alter the safety characteristics of this receiver and create a hazard to the user. Any design alterations or additions will void the manufacturer's warranty and may make you, the servicer, responsible for personal injury or property damage resulting therefrom. 4. Hot Chassis Warning a. Some TV receiver chassis are electrically connected directly to one conductor of the AC power cord and maybe safety-serviced without an isolation transformer only if the AC power plug is inserted so that the chassis is connected to the ground side of the AC power source. To confirm that the AC power plug is inserted correctly, with an AC voltmeter, measure between the chassis and a known earth ground. If a voltage reading in excess of 1.0 V is obtained, remove and reinsert the AC power plug in the opposite polarity and again measure the voltage potential between the chassis and a known earth ground. b. Some TV receiver chassis normally have 85V AC(RMS) between chassis and earth ground regardless of the AC plug polarity. This chassis can be safety-serviced only with an isolation transformer inserted in the power line between the receiver and the AC power source, for both personnel and test equipment protection. c. Some TV receiver chassis have a secondary ground system in addition to the main chassis ground. This secondary ground system is not isolated from the AC power line. The two ground systems are electrically separated by insulation material that must not be defeated or altered. 5. Observe original lead dress. Take extra care to assure correct lead dress in the following areas: a. near sharp edges, b. near thermally hot parts-be sure that leads and components do not touch thermally hot parts, c. the AC supply, d. high voltage, and, e. antenna wiring. Always inspect in all areas for pinched, out of place, or frayed wiring. Check AC power cord for damage. 6. Components, parts, and/or wiring that appear to have overheated or are otherwise damaged should be replaced with components, parts, or wiring that meet original specifications. Additionally, determine the cause of overheating and/or damage and, if necessary, take corrective action to remove any potential safety hazard.

2-2

LTVN_ISP

Precautions during Servicing A. Parts identified by the # symbol are critical for safety. Replace only with part number specified. B. In addition to safety, other parts and assemblies are specified for conformance with regulations applying to spurious radiation. These must also be replaced only with specified replacements. Examples: RF converters, RF cables, noise blocking capacitors, and noise blocking filters, etc. C. Use specified internal wiring. Note especially: 1) Wires covered with PVC tubing 2) Double insulated wires 3) High voltage leads D. Use specified insulating materials for hazardous live parts. Note especially: 1) Insulation Tape 2) PVC tubing 3) Spacers 4) Insulators for transistors. E. When replacing AC primary side components (transformers, power cord, etc.), wrap ends of wires securely about the terminals before soldering. F. Observe that the wires do not contact heat producing parts (heat sinks, oxide metal film resistors, fusible resistors, etc.) G. Check that replaced wires do not contact sharp edged or pointed parts. H. When a power cord has been replaced, check that 11~13 lb (5~6 kg) of force in any direction will not loosen it. I.

Also check areas surrounding repaired locations.

J. Use care that foreign objects (screws, solder droplets, etc.) do not remain inside the set. K. When connecting or disconnecting the internal connectors, first, disconnect the AC plug from the AC supply outlet. L. When installing parts or assembling the cabinet parts, be sure to use the proper screws and tighten certainly.

2-3

LTVN_ISP

Safety Check after Servicing Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and wires have been returned to original positions. Afterwards, perform the following tests and confirm the specified values in order to verify compliance with safety standards.

1. Clearance Distance When replacing primary circuit components, confirm specified clearance distance (d) and (d') between soldered terminals, and between terminals and surrounding metallic parts. (See Fig. 1)

Chassis or Secondary Conductor Primary Circuit

Table 1: Ratings for selected area AC Line Voltage

Region

Clearance Distance (d), (d’)

110 to 130 V

U.S.A. or Canada

≥ 3.2 mm (0.126 inches)

Note: This table is unofficial and for reference only. Be sure to confirm the precise values.

Fig. 1

2. Leakage Current Test Confirm the specified (or lower) leakage current between B (earth ground, power cord plug prongs) and externally exposed accessible parts (RF terminals, antenna terminals, video and audio input and output terminals, microphone jacks, earphone jacks, etc.) is lower than or equal to the specified value in the table below.

Exposed Accessible Part Z AC Voltmeter (High Impedance)

Measuring Method: (Power ON) Insert load Z between B (earth ground, power cord plug prongs) and exposed accessible parts. Use an AC voltmeter to measure across both terminals of load Z. See Fig. 2 and following table.

Earth Ground Power Cord Plug Prongs Fig. 2

Table 2: Leakage current ratings for selected areas AC Line Voltage

Region

Load Z

Leakage Current (i)

Earth Ground (B) to:

110 to 130 V

U.S.A. or Canada

0.15 μF CAP. & 1.5 kΩ RES. Connected in parallel

i ≤ 0.5 mA rms

Exposed accessible parts

Note: This table is unofficial and for reference only. Be sure to confirm the precise values.

2-4

LTVN_ISP

STANDARD NOTES FOR SERVICING Circuit Board Indications

How to Remove / Install Flat Pack-IC

1. The output pin of the 3 pin Regulator ICs is indicated as shown.

1. Removal With Hot-Air Flat Pack-IC Desoldering Machine:

Top View Out

1. Prepare the hot-air flat pack-IC desoldering machine, then apply hot air to the Flat Pack-IC (about 5 to 6 seconds). (Fig. S-1-1)

Bottom View In

Input

2. For other ICs, pin 1 and every fifth pin are indicated as shown.

5 Pin 1

10 3. The 1st pin of every male connector is indicated as shown.

Fig. S-1-1 2. Remove the flat pack-IC with tweezers while applying the hot air.

Pin 1

3. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6)

Pb (Lead) Free Solder

4. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6)

Pb free mark will be found on PCBs which use Pb free solder. (Refer to figure.) For PCBs with Pb free mark, be sure to use Pb free solder. For PCBs without Pb free mark, use standard solder.

CAUTION: 1. The Flat Pack-IC shape may differ by models. Use an appropriate hot-air flat pack-IC desoldering machine, whose shape matches that of the Flat Pack-IC. 2. Do not supply hot air to the chip parts around the flat pack-IC for over 6 seconds because damage to the chip parts may occur. Put masking tape around the flat pack-IC to protect other parts from damage. (Fig. S-1-2)

Pb free mark

3-1

TVN_SN

With Soldering Iron:

3. The flat pack-IC on the CBA is affixed with glue, so be careful not to break or damage the foil of each pin or the solder lands under the IC when removing it.

CBA

1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3)

Hot-air Flat Pack-IC Desoldering Machine

Flat Pack-IC

Desoldering Braid

Soldering Iron Masking Tape Tweezers

Flat Pack-IC

Fig. S-1-3 2. Lift each lead of the flat pack-IC upward one by one, using a sharp pin or wire to which solder will not adhere (iron wire). When heating the pins, use a fine tip soldering iron or a hot air desoldering machine. (Fig. S-1-4)

Fig. S-1-2

Sharp Pin Fine Tip Soldering Iron

Fig. S-1-4

3-2

TVN_SN

With Iron Wire:

2. Installation

1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3)

1. Using desoldering braid, remove the solder from the foil of each pin of the flat pack-IC on the CBA so you can install a replacement flat pack-IC more easily.

2. Affix the wire to a workbench or solid mounting point, as shown in Fig. S-1-5.

2. The â&#x20AC;&#x153; I â&#x20AC;? mark on the flat pack-IC indicates pin 1. (See Fig. S-1-7.) Be sure this mark matches the pin 1 on the PCB when positioning for installation. Then presolder the four corners of the flat pack-IC. (See Fig. S-1-8.)

3. While heating the pins using a fine tip soldering iron or hot air blower, pull up the wire as the solder melts so as to lift the IC leads from the CBA contact pads as shown in Fig. S-1-5.

3. Solder all pins of the flat pack-IC. Be sure that none of the pins have solder bridges.

4. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6)

Example :

5. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6) Note: When using a soldering iron, care must be taken to ensure that the flat pack-IC is not being held by glue. When the flat pack-IC is removed from the CBA, handle it gently because it may be damaged if force is applied.

Pin 1 of the Flat Pack-IC is indicated by a " " mark.

Hot Air Blower

Fig. S-1-7

Presolder

Iron Wire

Soldering Iron To Solid Mounting Point Fig. S-1-5 Flat Pack-IC CBA CBA

Fig. S-1-8

Fine Tip Soldering Iron

Flat Pack-IC Tweezers Fig. S-1-6

3-3

TVN_SN

Instructions for Handling Semiconductors Electrostatic breakdown of the semi-conductors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work.

1. Ground for Human Body Be sure to wear a grounding band (1 M立) that is properly grounded to remove any static electricity that may be charged on the body.

2. Ground for Workbench Be sure to place a conductive sheet or copper plate with proper grounding (1 M立) on the workbench or other surface, where the semi-conductors are to be placed. Because the static electricity charge on clothing will not escape through the body grounding band, be careful to avoid contacting semi-conductors with your clothing.

CBA

Grounding Band

1M立

CBA

1M立 Conductive Sheet or Copper Plate

3-4

TVN_SN

CABINET DISASSEMBLY INSTRUCTIONS Screw Torque Specification Ref. No.

Part Number

Step/ Loc. No.

Tightening Torque

Part Name

SCREW P-TIGHT L4 GBHP3080 (M3X8 BIND HEAD+ BLK) S-TIGHT L23 GBJS3060 SCREW (M3X6 BIND HEAD+) 5.2±0.9lb·in S-TIGHT SCREW L24 GBHS3060 (M3X6 BIND HEAD+ BLACK) STAND SCREW KIT P-TIGHT (approx. SSK1 1ESA34670 (SCREW M4X14 BIND 8.7±0.9lb·in)* HEAD+BLK)

[2] Stand Assembly

[6]

4(S-6), CN3013*1, Digital Main D3 CN3006*2 CN3101, CBA Unit D5 Jack Holder

---

[7]

LCD Panel Assembly

D3 ----------------

---

[8]

Front Cabinet

8(S-7), Decoration Plate*3

[9]

Function CBA Unit

Sensor Lens, Shield Plate, Control Plate

↓ (2)

D3 4(S-5), CN501, D5 CN601, CN1001

↓ (3)

---

↓ (4)

↓ (5)

*2: TYPE B models *3: 32PFL3508 models

[4] Bottom Cover

[5] Power Supply CBA

Note

*1: TYPE A models

[3] Speaker

[1] Rear Cover

Removal

Power Supply CBA

↓ (1)

This flowchart indicates the disassembly steps for the cabinet parts and the CBA in order to gain access to items to be serviced. When reassembling, follow the steps in reverse order. Bend, route and dress the cables as they were.

Fig. No.

[5]

* For reference

1. Disassembly Flowchart

Part

Note: (1) Order of steps in procedure. When reassembling, follow the steps in reverse order. These numbers are also used as the Identification (location) No. of parts in figures.

[6] Digital Main CBA Unit

[7] LCD Panel Assembly

(2) Parts to be removed or installed. (3) Fig. No. showing procedure of part location

[8] Front Cabinet

(4) Identification of parts to be removed, unhooked, unlocked, released, unplugged, unclamped, or desoldered. P = Spring, L = Locking Tab, S = Screw, H = Hex Screw, CN = Connector e.g. 2(S-2) = two Screws of (S-2), 2(L-2) = two Locking Tabs of (L-2)

[9] Function CBA Unit

2. Disassembly Method Step/ Loc. No.

Part

Fig. No.

Removal

(5) Refer to the following "Reference Notes in the Table."

Note

[1]

Rear Cover D1 7(S-1), 5(S-2)

---

[2]

Stand Assembly

D1 3(S-3)

---

[3]

Speaker

D2 CN3801 D5

---

[4]

Bottom Cover

D2 4(S-4)

Important Precautions concerning the LCD Panel Assembly: 1. When you disassemble/re-assemble the Bottom Cover for 32PFL3508/F8 (Serial No.: XA2) model. • The CBA which is connected to the Digital Main CBA Unit with CL3006 cannot be replaced alone. This CBA can only be supplied as LCD Panel

4-1

PL13.8_DC

2. When you disassemble/re-assemble the Front Cabinet or Function CBA Unit

• The Function CBA Unit and Sensor Lens are fixed in place by the hooks. Make sure these hooks are not damaged. Make sure the Function CBA Unit and Sensor Lens are securely in place when reassembling.

• Be careful not to break the hooks. If you pull with too much force, the hooks may be damaged.

• The screw tightening torque must be 5.2lb·in (6kgf·cm).

• Be careful not to scratch the display panel when assembling.

• Make sure the tact switches operate normally after replacing the Front Cabinet, Function CBA Unit, Sensor Lens, or Shield Plate.

Assembly. Be careful not to touch this CBA unnecessarily.

• Be careful not to scratch the rear frame when disassembling/re-assembling or when tightening the screws.

• Make sure to replace the Control Plate and Decoration Plate to a new one when replacing the Front Cabinet.

• Make sure the Shield Plate is placed properly.

[1] Rear Cover

(S-1)

[2] Stand Assembly (S-2)

(S-3)

Fig. D1

4-2

PL13.8_DC

[4] Bottom Cover*1

(S-4)

[3] Speaker

(S-4)

Fig. D2 *1: For 32PFL3508/F8 (Serial No.:XA2) model, make sure to read the precautions on pages 4-1 and 4-2 when you disassemble/re-assemble the Bottom Cover.

[7] LCD Panel Assembly

[6] Digital Main CBA Unit Jack Holder

(S-6)

[5] Power Supply CBA (S-5)

Fig. D3

4-3

PL13.8_DC

[8] Front Cabinet*2

Hook*2 Shield Plate*2 Decoration Plate*2 (for 32PFL3508 models)

(S-7)

Sensor Lens*2

Control Plate*2

[9] Function CBA Unit*2 (S-7)

Fig. D4 *2: Make sure to read all the precautions on page 4-2 when you disassemble/re-assemble the Front Cabinet or Function CBA Unit.

4-4

PL13.8_DC

TV Cable Wiring Diagram

To LCD Panel Assembly

Digital Main CBA Unit Power Supply CBA *1 CN3013 CN1001

*2 CN3006

CN3701

CN501

CN601

CN3101 CN3801

To AC Cord

Function CBA Unit

To Speaker

CN4052

*1: TYPE A *2: TYPE B

Fig. D5

4-5

PL13.8_DC

ELECTRICAL ADJUSTMENT INSTRUCTIONS How to set up the service mode: General Note: “CBA” is abbreviation for “Circuit Board Assembly.”

Service mode:

Note: Electrical adjustments are required after replacing circuit components and certain mechanical parts. It is important to perform these adjustments only after all repairs and replacements have been completed. Also, do not attempt these adjustments unless the proper equipment is available.

2. Press [MENU] button to display Setup menu.

1. Turn the power on. 3. Select “Features”. 4. Select “Software Upgrade”. 5. Select “Current Software Info”. 6. Press [0], [6], [2], [5], [9], [6] and [INFO] buttons on the remote control unit in this order. The following screen appears.

Test Equipment Required

"*" differs depending on the models.

1. Remote control unit

Code: Pic code: Panel-Option code: MIPS:

2. Color Analyzer, CA-310 (KONICA MINOLTA Luminance meter) or measuring instrument as good as CA-310.

*******-**-**-****-** ***-*****-***-***-*-** **-***-***-***-*** Push 0 key

Press "POWER" key to exit. Safety: HDMI EDID: HDMI UART: Touch Sensor Ver:

5-1

Safety_Non ** OFF -.-- / ---

Total Watch Time: ***** Lightsensor: **

PL13.8EA

1. Purity Check Mode

The VCOM Adjustment should be performed when replacing the Digital Main CBA for 32PFL1508/F8 (Serial No.: DS1).

This mode cycles through full-screen displays of red, green, blue, and white to check for non-active pixels. 1. Enter the service mode.

2. VCOM Adjustment

2. Each time the [7] button on the remote control unit is pressed, the display changes as follows.

Test Point

Adj. Point

Screen

[CHANNEL UP/DOWN] buttons

M. EQ.

Spec.

Color analyzer

See below

Purity Check Mode White mode [7] button

Figure

To avoid interference from ambient light, this adjustment should be performed in a dark room.

[7] button Black mode

Perpendicularity

[7] button White 50% mode

Color Analyzer 1. Operate the unit for more than 60 minutes. 2. Set the color analyzer at the zero point calibration and bring the optical receptor pointing at the center of the LCD-Panel. Note: The optical receptor must be set perpendicular to the LCD Panel surface. 3. Enter the service mode. 4. Press [2] button on the remote control unit. 5. Press [CHANNEL UP/DOWN] buttons on the remote control unit so that the color analyzer value becomes minimum. 6. To cancel or to exit from the VCOM Adjustment, press [CH RETURN] or [PREV CH] button.

[7] button Red, Green, Blue mode

[7] button V-ramp mode

[7] button White 20% mode

Note: When entering this mode, the default setting is White mode.

3. To cancel or to exit from the Purity Check Mode, press [CH RETURN] or [PREV CH] button.

5-2

PL13.8EA

The White Balance Adjustment should be performed when replacing the LCD Panel or Digital Main CBA.

6. Press [MENU] button. The internal Raster signal appears in the screen. (“Internal (Single)” appears in the upper right of the screen as shown below.)

3. White Balance Adjustment Internal (Single)

Purpose: To mix red and blue beams correctly for pure white. Symptom of Misadjustment: White becomes bluish or reddish. ITEM

HDB

SPECIFICATION

Color temperature

x= 0.272 ± 0.003 y= 0.278 ± 0.003

Input Signal

Internal pattern (40/80% raster)

7. Press [CHANNEL UP/DOWN] buttons to adjust the color temperature becomes 12000°K (x= 0.272 / y= 0.278 ± 0.003).

Measurement point Screen center M. EQ.

CA-310 (KONICA MINOLTA Luminance meter) or measuring instrument as good as CA-310.

Aging time

60min. (Retail MODE/100IRE Raster HDMI 1080i@60)

MODE setting of TV

Shipment setting/ Retail MODE

Ambient temperature

25°C ± 5°C

8. Press [1] button to select the “HDR” for High Drive Red adjustment (“HDR” appears in the screen.) and press [CHANNEL UP/DOWN] buttons to adjust the color temperature. 9. If necessary, adjust the “HDB” or “HDR” again. 10. Press [6] button to select the “LDB” for Low Drive Blue adjustment (“LDB” appears in the screen.) and press [CHANNEL UP/DOWN] buttons to adjust the color temperature.

Internal (Single)

1. Operate the unit for more than 60 minutes. 2. Enter the service mode. 3. Press [VOLUME DOWN] button three times on the remote control unit to select “Drive setting” mode. “Drive” appears in the screen.

LDB

4. Set the color analyzer at the CHROMA mode and zero point calibration. Bring the optical receptor pointing at the center of the LCD-Panel.

11. Press [4] button to select the “LDR” for Low Drive Red adjustment (“LDR” appears in the screen.) and press [CHANNEL UP/DOWN] buttons to adjust the color temperature.

To avoid interference from ambient light, this adjustment should be performed in a dark room.

12. If necessary, adjust the “LDB” or “LDR” again.

Perpendicularity

13. Press [VOLUME DOWN] button to shift to the “Debugging Message” mode. If there is no message under “[WB]” section, this adjustment completes. If “Drive settings are NG. Retry again.” is displayed, repeat above steps from 5. to 12. Then check “Debugging Message” again. If “Drive settings are NG. Retry again.” is displayed, replace the LCD Panel or Digital Main CBA.

Color Analyzer

Note: The optical receptor must be set perpendicularly to the LCD Panel surface.

14. To cancel or to exit from the White Balance Adjustment, press [CH RETURN] or [PREV CH] button.

5. Press [3] button to select the “HDB” for High Drive Blue adjustment. (“HDB” appears in the screen.)

5-3

PL13.8EA

HOW TO INITIALIZE THE LCD TV The purpose of initialization is to place the set in a new out of box condition. The customer will be prompted to select a language and program channels after the set has been initialized. To put the program back at the factory-default, initialize the LCD TV using the following procedure. NOTE: Disconnect any device from the USB Port before you conduct on this procedure.

1. Turn the power on. 2. Enter the service mode. - To cancel the service mode, press [ ] button on the remote control unit. 3. Press [BACK] button to enter the Panel Key Confirmation Menu. 4. Press any button on the control panel. 5. Press [INFO] button to proceed with the self check mode. 6. Make sure to confirm the â&#x20AC;&#x153;INITIALIZED FINISHâ&#x20AC;? appears in the green screen. 7. Unplug the AC Cord and plug it back on again.

6-1

PL13.8_INT

FIRMWARE RENEWAL MODE Equipment Required a. USB storage device b. Remote Control Unit

Firmware Update Procedure User Upgrade (Filename example: TVNB012_00_PF_XX91_AC.ecc) Upgrade the firmware only. The setting values will not be initialized. The User Upgrade and the Firmware Upgrade (Factory Upgrade) will be done by the same file. If you want to upgrade the firmware and initialize the setting values also, add “FACT_” at the beginning of the filename. If you want to upgrade the firmware only and leave the setting values as they are, eliminate the “FACT_” from the filename. Update procedure 1. Turn the power on. 2. Press [MENU] button to display Menu. 3. Select “Features”. 4. Select “Software Upgrade”. 5. Select “Upgrade” to display Upgrade screen. 6. Press [OK] button to display Software Upgrade screen. 7. Select “USB” and press [OK] button. 8. Insert the USB storage device to the USB port as shown below.

11. The update will start and the following will appear in the screen. "*" differs depending on the models.

Software Upgrade

Software upgrade in progress. Please wait. Do not remove the USB storage device or turn the TV off while upgrade is in progress. Current Version: *******-***-*-***-**** New Version: *******-***-*-***-****

Downloading... 0%

Rear Cabinet

Note: If the above screen isn’t displayed, repeat from step 1. The appearance shown in *1 is described as follows.

USB port

Appearance

State

Downloading...

Downloading the firmware from the USB storage device.

Writing...

Writing the downloaded firmware in flash memory.

Checking...

Checking the new firmware.

USB storage device

12. When the firmware update is completed, the following will appear in the screen. Software Upgrade

9. Select “Check” and press [OK] button. 10. Select “Upgrade” and press [OK] button to start software upgrade.

The software upgrade is completed. Remove USB storage device, turn TV off then on again.

Remove the USB storage device from the USB port. Turn the power off and turn the power on again.

7-1

PL13.8FW

Factory Upgrade (Firmware Upgrade/Flash Upgrade) Firmware Upgrade (Filename example: FACT_TVNB012_00_PF_XX91_AC.ecc) Upgrade the firmware and initialize the setting values. The User Upgrade and the Firmware Upgrade (Factory Upgrade) will be done by the same file. If you want to upgrade the firmware and initialize the setting values also, add “FACT_” at the beginning of the filename. If you want to upgrade the firmware only and leave the setting values as they are, eliminate the “FACT_” from the filename. Flash Upgrade (Filename example: ALL_TVNB012_00_PF_XX91_AC.ecc) Upgrade the firmware and initialize the setting values along with the factory default such as White Balance, etc. Before the upgrade, you will need to make a note of all the factory default so you will be able to set it back on the TV after the initialization. The Flash Upgrade will be done by it's unique file. The User Upgrade/Firmware Upgrade (Factory Upgrade) file cannot be used for this upgrade. Update procedure 1. Turn the power off. 2. Insert the USB storage device to the USB port as shown below.

The appearance shown in *1 is described as follows. Appearance

Rear Cabinet

State

Downloading...

Downloading the firmware from the USB storage device.

Writing...

Writing the downloaded firmware in flash memory.

Checking...

Checking the new firmware.

USB port

5. When the firmware update is completed, the following will appear in the screen. USB storage device

Software Upgrade

The software upgrade is completed. Remove USB storage device, turn TV off then on again.

3. Turn the power on. 4. The update will start and the following will appear in the screen.

Remove the USB storage device from the USB port. Turn the power off and turn the power on again. Service mode initial screen with a word “INITIALIZED” will appear in the screen. The color of the word “INITIALIZED” will change from red to green when initialization is completed.

"*" differs depending on the models.

Software Upgrade

Downloading... 0%

Note: If the above screen isn’t displayed, repeat from step 1.

7-2

PL13.8FW

TROUBLESHOOTING Note: This Troubleshooting section covers the entire PL13.8 chassis models. Thus some Reference number of parts shown below may not be used depending on the model. Please refer to the parts list for each model.

[Power Supply Section] FLOW CHART NO.1 The power cannot be turned on. No

Is the fuse (F602) normal?

See FLOW CHART No.2 <The fuse blows out.>

Yes

Is normal state restored when once unplugged power cord is plugged again after several seconds?

Yes Is the P-ON+21V line voltage normal?

Check if there is any leak or short-circuit on the primary circuit component and repair it if defective. (C607, D601, D602, D603, D604, D605, D607A, D608, D609A, D621, D623, Q601, Q602, Q621, R611, T601)

Yes

Check each rectifying circuit of the secondary circuit and repair it if defective. FLOW CHART NO.2 The fuse blows out.

Check if there is any leak or short-circuit on the primary circuit component and repair it if defective.

Check if there is any leak or short-circuit on the each rectifying circuit component of secondary side and repair it if defective.

Make sure to repair the primary circuit component before replacing the fuse (F602). FLOW CHART NO.3 When the output voltage fluctuates.

Does the photocoupler circuit on the secondary side operate normally?

Check IC602, D660, D661, Q653 and their periphery circuit. Repair it if defective.

Yes

Check IC602, D605, D607A, D608, D609A, D610, D621, D623, Q601, Q602, Q621 and their periphery circuit. Repair it if defective. FLOW CHART NO.4 When buzz sound can be heard in the periphery of power circuit.

Check if there is any short-circuit on the rectifying diode and the circuit in each rectifying circuit of the secondary side. Repair it if defective. (D650, D651, D653, D655, Q656, Q658)

8-1

PL13.8ATR

FLOW CHART NO.5 P-ON+21V is not output.

Is approximately +21V voltage supplied to the cathode of D650(D651)?

Check D650, D651, C651, C652, C653 and their periphery circuit. Repair it if defective.

Yes

Check if there is any leak or short-circuit on the load circuit. Repair it if defective.

FLOW CHART NO.6 AMP+13V is not output. No

Is approximately +13V voltage supplied to the cathode of D653(D655)?

Check D653, D654, D655, C654, C655 and their periphery circuit. Repair it if defective.

Yes

Check if there is any leak or short-circuit on the load circuit. Repair it if defective.

FLOW CHART NO.7 AL+3.3V is not output.

Is approximately +13V voltage supplied to the collector of Q656?

Is approximately +13V voltage supplied to the emitter of Q658?

Yes

Replace Q658.

Is approximately +4V voltage supplied to the base of Q656?

Check D653, D654, D655, C654, C655 and their periphery circuit. Repair it if defective.

Check D662 and their periphery circuit. Repair it if defective.

Yes

Replace Q656.

8-2

PL13.8ATR

[Video Signal Section] FLOW CHART NO.1 The key operation is not functioning.

When touching each buttons, does the Pin(6) voltage of CN4052 decrease?

Replace the Function CBA Unit.

Yes Replace the Digital Main CBA Unit.

FLOW CHART NO.2 No operation is possible from the remote control unit. (Operation is possible from the unit.)

Is approximately +3.3V voltage supplied to Pin(1) of CN4052? Yes Is the "L" pulse supplied to Pin(5) of CN4052?

Check AL+3.3V line and repair it if defective.

Replace the Function CBA Unit.

Yes Replace the Digital Main CBA Unit.

FLOW CHART NO.3 Picture does not appear normally.

Is approximately +21V voltage supplied to Pin(20, 21, 22, 23) of CN501? Yes Is approximately +3.3V voltage supplied to Pin(8) of CN501? Yes

See FLOW CHART NO.5 <P-ON+21V is not output. [Power Supply Section]>

See FLOW CHART NO.7 <AL+3.3V is not output. [Power Supply Section]>

Digital Main CBA Unit or LCD Panel Assembly may be defective. Check and replace these parts.

8-3

PL13.8ATR

[Audio Signal Section] FLOW CHART NO.1 Audio is not output normally.

Is approximately +13V voltage supplied to Pin(15, 16, 17, 18) of CN501? Yes Is approximately +3.3V voltage supplied to Pin(8) of CN501? Yes Are the audio signals output to Pin(1, 2, 3, 4) of CN3801?

See FLOW CHART NO.6 <AMP+13V is not output. [Power Supply Section]>

See FLOW CHART NO.7 <AL+3.3V is not output. [Power Supply Section]>

No Replace the Digital Main CBA Unit.

Yes

SP3801, SP3802 or CL3801 may be defective. Check and replace these parts.

8-4

PL13.8ATR

USB JACK

9-1

SCK SI SO CS

6 5 2 1

AUDIO-MUTE COMP-DET HP-MUTE HP-DET

IC3006 (MEMORY)

TO VIDEO/AUDIO BLOCK DIAGRAM

CN3009 USBDP USBDN

X3001 25MHz OSC

SCK SIN SOUT CS

RESET J15

P-ON-H2 B16

SCL R12 SDA T12

VCOM-PWM F2

KEY-IN1 A15 REMOTE C14 LED1 D14

DIGITAL MAIN CBA UNIT

PROTECT3 B13 BACKLIGHT-SW E2 BACKLIGHT-ADJ F3

AUDIO-MUTE COMP-DET HP-MUTE HP-DET

H15 XIN25 H16 XOUT25

T11 P11 R11 P12

C1 N12 G13 K16

R10 USBDP T10 USBDN

IC3005 (MAIN MICRO CONTROLLER)

Q3005

RESET IC3009

BACKLIGHT-SW

Q3006

AL+3.3V

TO VIDEO/AUDIO BLOCK DIAGRAM

TU3901 (TUNER UNIT) 4 SCL 3 SDA

Q3007 VCOM DRIVE

LED DRIVE Q3501, Q3502

FUNCTION CBA UNIT

P-ON+5V

KEY SWITCH

D4051 POWER

PROTECT3 BACKLIGHT-SW BACKLIGHT-ADJ

CN501 3 5 7 CN3701 3 PROTECT3 5 BACKLIGHT-SW 7 BACKLIGHT-ADJ

TO LED BACKLIGHT DRIVE BLOCK DIAGRAM

TO POWER SUPPLY BLOCK DIAGRAM

POWER SUPPLY CBA

P-ON-H2 RESET

CN501 6 4

[TYPE B]

LCD PANEL ASSEMBLY

CN4052 6 5 4

CN3701 6 P-ON-H2 4 RESET

CN3006 27 VCOM-PWM

CN3101 4 KEY-IN1 5 REMOTE 6 LED1

REMOTE SENSOR

RS4051

1. System Control Block Diagram

BLOCK DIAGRAMS

PL13.8BLS

9-2

SP3802 SPEAKER R-CH

SP3801 SPEAKER L-CH

JK3703 HEADPHONE JACK

DIGITAL AUDIO-OUT (COAXIAL)

AUDIO(R)-IN

AUDIO(L)-IN

COMPONENT -Pr-IN

COMPONENT -Pb-IN

COMPONENT -Y/VIDEO-IN

JK3001 PC-RGB -IN

JK3701

JK3702

Q3302

Q3301

IC3014

IC3013

BUFFER

SP(L)+ SP(L)SP(R)SP(R)+

BUFFER GATE

CN3801 1 2 3 4

Q3701 BUFFER

20,21 17,18

25,26 22,23

1 7

6dB

DRIVE

3 5

MUTE 2

CONTROL LOGIC

PWM LOGIC

IC3801 (AUDIO AMP)

6dB

IC3851 (HEADPHONE AMP)

DIF-OUT1 6 DIF-OUT2 7 IF-AGC 5

TU3901 (TUNER UNIT)

1 2

DIGITAL MAIN CBA UNIT

Q3861

Q3803 P-ON+5V Q3802

Q3801

BACKLIGHT-SW

HP-DET AUDIO-MUTE COMP-DET HP-MUTE

AMP(R)-OUT

AMP(L)-OUT

SPDIF

AUDIO(L)-IN AUDIO(R)-IN

COM-VIDEO-Y/VIDEO-IN COM-VIDEO-Pb-IN COM-VIDEO-Pr-IN

DIF-OUT1 DIF-OUT2 IF-AGC

VGA-R-IN VGA-G-IN VGA-B-IN VGA-HSYNC VGA-VSYNC VGA-SCL VGA-SDA

AUDIO SIGNAL

TO SYSTEM CONTROL BLOCK DIAGRAM

TO DIGITAL SIGNAL PROCESS BLOCK DIAGRAM

VIDEO SIGNAL

2. Video/Audio Block Diagram

PL13.8BLVA

9-3

TMDS-D0(+) TMDS-D0(-) TMDS-D1(+) TMDS-D1(-) TMDS-D2(+) TMDS-D2(-) TMDS-CLOCK(+) TMDS-CLOCK(-) HDMI-DATA HDMI-CLOCK

7 9 4 6 1 3 10 12 16 15

TO VIDEO/AUDIO BLOCK DIAGRAM

TMDS-D0(+) TMDS-D0(-) TMDS-D1(+) TMDS-D1(-) TMDS-D2(+) TMDS-D2(-) TMDS-CLOCK(+) TMDS-CLOCK(-) HDMI-DATA HDMI-CLOCK

JK3002 HDMI-IN2

7 9 4 6 1 3 10 12 16 15

JK3004 HDMI-IN1

TO VIDEO/AUDIO BLOCK DIAGRAM

57 56 60 59 63 62 54 53 51 52

26 27 23 24 20 21 17 18

SCL1 SDA1 SCL3 SDA3

SCL2 SDA2 SCL0 SDA0 15 14 7 6

IC3011 (HDMI SERIAL EEPROM)

HDMI SW

IC3018 (HDMI SW)

VGA-SCL VGA-SDA

2 3 10 11

8 7 11 10 14 13 5 4 1 2

42 41 45 44 48 47 39 38 36 37

AUDIO(L)-IN AUDIO(R)-IN SPDIF AMP(L)-OUT AMP(R)-OUT

IF-AGC

DIF-OUT1 DIF-OUT2

VGA-R-IN VGA-G-IN VGA-B-IN COM-VIDEO-Y/VIDEO-IN COM-VIDEO-Pb-IN COM-VIDEO-Pr-IN

VGA-HSYNC VGA-VSYNC

VIDEO DECODER

HDMI I/F

AUDIO DECODER

AUDIO I/F

G14 HDMI-SCL F14 HDMI-SDA

JK3003 HDMI-IN3 TMDS-D0(+) 7 TMDS-D0(-) 9 TMDS-D1(+) 4 TMDS-D1(-) 6 TMDS-D2(+) 1 TMDS-D2(-) 3 TMDS-CLOCK(+) 10 TMDS-CLOCK(-) 12 HDMI-DATA 16 HDMI-CLOCK 15

B4 A4 B3 A3 B2 A2 B1 A1

A8 B8 N10 B7 A7

A/D CONVERTER

DEMODULATOR /MPEG DECODER

A16 IF-AGC

A12 B12

C11 A9 C7 C9 D8 B11 C10

A14 HSYNC B14 VSYNC

IC3005 (DIGITAL SIGNAL PROCESS)

DIGITAL SIGNAL PROCESS

LVDS TX

H1,H2,J1,J2,J4,K1, K3,L1,L2,M1-M3,N1

N4,N7,N8,P3,P4, P6-P8,R3,R4,R6, R8,T2-T5

N16 N15 P16 P15 R16 R15 R14 T14 T16 T15

DIGITAL MAIN CBA UNIT

B1,B9,C2,C8, D1,D3,D7,D9, F1,F9,G2,G8, DATA(0-15) H1,H3,H7,H9 M2,M3,M7,M8, N2,N3,N7,N8, ADDRESS(0-12) P2,P3,P7,P8,R2

CN3013 12 13 15 16 18 19 24 25 21 22

AUDIO SIGNAL

IC3002 (DDR2 SDRAM)

VIDEO SIGNAL

RX0(-) RX0(+) RX1(-) RX1(+) RX2(-) RX2(+) RX3(-) RX3(+) RXCLK(-) RXCLK(+)

LCD PANEL ASSEMBLY

3. Digital Signal Process Block Diagram [TYPE A]

PL13.8ABLD

9-4

TMDS-D0(+) TMDS-D0(-) TMDS-D1(+) TMDS-D1(-) TMDS-D2(+) TMDS-D2(-) TMDS-CLOCK(+) TMDS-CLOCK(-) HDMI-DATA HDMI-CLOCK

TO VIDEO/AUDIO BLOCK DIAGRAM

TMDS-D0(+) 7 TMDS-D0(-) 9 TMDS-D1(+) 4 TMDS-D1(-) 6 TMDS-D2(+) 1 TMDS-D2(-) 3 TMDS-CLOCK(+) 10 TMDS-CLOCK(-) 12 HDMI-DATA 16 HDMI-CLOCK 15

JK3002 HDMI-IN2

7 9 4 6 1 3 10 12 16 15

JK3004 HDMI-IN1

TO VIDEO/AUDIO BLOCK DIAGRAM

57 56 60 59 63 62 54 53 51 52

26 27 23 24 20 21 17 18

SCL1 SDA1 SCL3 SDA3

SCL2 SDA2 SCL0 SDA0 15 14 7 6

IC3011 (HDMI SERIAL EEPROM)

HDMI SW

IC3018 (HDMI SW)

VGA-SCL VGA-SDA

2 3 10 11

8 7 11 10 14 13 5 4 1 2

42 41 45 44 48 47 39 38 36 37

AUDIO(L)-IN AUDIO(R)-IN SPDIF AMP(L)-OUT AMP(R)-OUT

IF-AGC

DIF-OUT1 DIF-OUT2

VGA-R-IN VGA-G-IN VGA-B-IN COM-VIDEO-Y/VIDEO-IN COM-VIDEO-Pb-IN COM-VIDEO-Pr-IN

VGA-HSYNC VGA-VSYNC

VIDEO DECODER

HDMI I/F

AUDIO DECODER

AUDIO I/F

G14 HDMI-SCL F14 HDMI-SDA

JK3003 HDMI-IN3 TMDS-D0(+) 7 TMDS-D0(-) 9 TMDS-D1(+) 4 TMDS-D1(-) 6 TMDS-D2(+) 1 TMDS-D2(-) 3 TMDS-CLOCK(+) 10 TMDS-CLOCK(-) 12 HDMI-DATA 16 HDMI-CLOCK 15

B4 A4 B3 A3 B2 A2 B1 A1

A8 B8 N10 B7 A7

A/D CONVERTER

DEMODULATOR /MPEG DECODER

A16 IF-AGC

A12 B12

C11 A9 C7 C9 D8 B11 C10

A14 HSYNC B14 VSYNC

IC3005 (DIGITAL SIGNAL PROCESS)

DIGITAL SIGNAL PROCESS

LVDS TX

H1,H2,J1,J2,J4,K1, K3,L1,L2,M1-M3,N1

N4,N7,N8,P3,P4, P6-P8,R3,R4,R6, R8,T2-T5

N16 N15 P16 P15 R14 T14 T16 T15 R16 R15

DIGITAL MAIN CBA UNIT

B1,B9,C2,C8, D1,D3,D7,D9, F1,F9,G2,G8, DATA(0-15) H1,H3,H7,H9 M2,M3,M7,M8, N2,N3,N7,N8, ADDRESS(0-12) P2,P3,P7,P8,R2

CN3006 21 20 19 18 11 10 13 12 16 15

AUDIO SIGNAL

IC3002 (DDR2 SDRAM)

VIDEO SIGNAL

ML1(+) ML1(-) ML2(+) ML2(-) ML4(+) ML4(-) ML3(+) ML3(-) MLCLK(+) MLCLK(-)

LCD PANEL ASSEMBLY

3. Digital Signal Process Block Diagram [TYPE B]

PL13.8BBLD

TO SYSTEM CONTROL BLOCK DIAGRAM

P-ON+21V

BACKLIGHT-SW BACKLIGHT-ADJ PROTECT3

9-5 7

13 5 6

CONTROL LOGIC

POWER SUPPLY CBA

FAIL DETECT

VREG

IC1001 (LED BACKLIGHT DRIVER)

DRIVE

OVP

Q1001

Q1003

CN1001 1 VLED 2 ILED

LCD PANEL ASSEMBLY

4. LED Backlight Drive Block Diagram

PL13.8BLBD

AC601 AC CORD

2.5A 250V

L601 F602 2.5A/250V LINE FILTER

9-6

Q602 SWITCHING CONTROL

Q601 SWITCHING

CN601 B W

HOT CIRCUIT. BE CAREFUL.

BRIDGE RECTIFIER

D601- D604

Q621 OVER VOLTAGE PROTECT

LINE FILTER

L602

2.5A 250V

COLD

HOT

IC602 ERROR VOLTAGE DET

T601

CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F602) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail.

Q653

Q650 RESET

Q656, Q658 +3.3V REG.

POWER SUPPLY CBA

AMP+13V AL+3.3V P-ON+21V

TO SYSTEM CONTROL BLOCKDIAGRAM

P-ON+21V

DIGITAL MAIN CBA UNIT

RESET P-ON-H2

CN3701 15-18 8 20-23

NOTE: The voltage for parts in hot circuit is measured using hot GND as a common terminal.

CN501 15-18 AMP+13V 8 AL+3.3V 20-23 P-ON+21V

CAUTION ! : For continued protection against risk of fire, replace only with same type 2.5A, 250V fuse. ATTENTION : Utiliser un fusible de rechange de mĂŞme type de 2.5A, 250V.

5. Power Supply Block Diagram

PL13.8BLP

SCHEMATIC DIAGRAMS / CBA AND TEST POINTS Standard Notes WARNING Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts that have these special safety characteristics are identified in this manual and its supplements; electrical components having such features are identified by the mark “#” in the schematic diagram and the parts list. Before replacing any of these components, read the parts list in this manual carefully. The use of substitute replacement parts that do not have the same safety characteristics as specified in the parts list may create shock, fire, or other hazards.

Notes: 1. Do not use the part number shown on these drawings for ordering. The correct part number is shown in the parts list, and may be slightly different or amended since these drawings were prepared. 2. All resistance values are indicated in ohms (K = 103, M = 106). 3. Resistor wattages are 1/4W or 1/6W unless otherwise specified. 4. All capacitance values are indicated in μF (P = 10-6 μF). 5. All voltages are DC voltages unless otherwise specified. 6. This schematic diagrams are masterized version that should cover the entire PL13.8 chassis models. Thus some parts in detail illustrated on this schematic diagrams may vary depend on the model within the PL13.8 chassis. Please refer to the parts lists for each models. 7. The Circuit Board layout illustrated on this service manual is the latest version for this chassis at the moment of making this service manual. Depend on the mass production date of each model, the actual layout of each Board may differ slightly from this version.

10-1

PL13.8SC

LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWING PAGES: 1. CAUTION: CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE_A,_V FUSE. ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MĂ&#x160;ME TYPE DE_A,_V.

2. CAUTION: Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F602) is blown, first check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail.

3. Note: 1. Do not use the part number shown on the drawings for ordering. The correct part number is shown in the parts list, and may be slightly different or amended since the drawings were prepared. 2. To maintain original function and reliability of repaired units, use only original replacement parts which are listed with their part numbers in the parts list section of the service manual.

4. Voltage indications on the schematics are as shown below: Plug the TV power cord into a standard AC outlet.:

1 (Unit: Volt)

5.0

Voltage

5.0

Power on mode

Indicates that the voltage is not consistent here.

5. How to read converged lines 1-D3 Distinction Area Line Number (1 to 3 digits)

3 AREA D3

2 Examples: 1. "1-D3" means that line number "1" goes to the line number "1" of the area "D3". 1 2. "1-B1" means that line number "1" goes to the line number "1" of the area "B1".

1-B1

AREA B1 1-D3 A

6. Test Point Information : Indicates a test point with a jumper wire across a hole in the PCB. : Used to indicate a test point with a component lead on foil side. : Used to indicate a test point with no test pin. : Used to indicate a test point with a test pin.

The reference number of parts on Schematic Diagrams/CBA can be retrieved by application search function.

10-2

PL13.8SC

Power Supply Schematic Diagram [TYPE A] CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F602) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail.

2.5A 250V

C1003 1

C1002 470/25V

C1009 1/100V

CN601 W B C603 1000P/250V

SA601 VARISTOR C602 1000P/250V C604 0.22/275V C616 1000P/250V L601 LINE FILTER

R1027 22K JS602 OPEN

JS601 OPEN

SA602 GT601 OPEN OPEN

JS603 C614 0.22/275V

D601 1N5406BH

L602 LINE FILTER

JS605 OPEN

JS606 OPEN

D602 1N5406BH

R1023 3.9K

R1021 0

R1024 1.5K

R1022 10K

C1014 OPEN

D655A OPEN D653 SB3A0BH

D1005 HSC119

D653A OPEN

D603 1N5406BH C617 100P/250V

C654 470/16V

C655 470/16V D654 1ZB20BB

D654A OPEN

R663 OPEN

R664 OPEN

R665 OPEN

R651 D656 1 RS1BJTD

0.1 S

C607 1800P

C608 0.022

2.6

Q602 2SC5344SY SWITCHING CONTROL 0.4

R608 1.5K

R606 330

R607 330

D605 MM5Z4V3B

C651 470/25V

C622 10

C621 OPEN

IC602 TLP781F ERROR VOLTAGE DET

0.4 3

D608 1ZB36BB

R615 OPEN

C609 0.068

20.4

R655 180

19.0

R657 3.9K

12 8.1 11 12.6

R658 2.7K

19.0 2.5 0 D660 SL431A-AT

R659 27K R660 3.9K

12.8 12.8 3.9

R666 0

R675 68K R674 0

R667 8.2K

GP002 EARTH PLATE

GP003 EARTH PLATE

R1005 R1004 100K 10K

R685 R686 R687 OPEN OPEN OPEN

D661 HSC119

R670 270

0.6

D405 OPEN D406 OPEN

C664 OPEN

C633 OPEN C630 OPEN 3.4 Q656 KTC3875S-Y-RTK/P (+3.3V REG.)

C665 R682 0.1 0

R661 3.3K

4 3

0 Q653 KTC3875S-Y-RTK/P (SWITCHING) 0

R619 OPEN

GP001 EARTH PLATE

R1025 1K

Q658 2SA950-O (+3.3V REG.) 13.4 3.4

R671 270

C663 100/10V

R662 3.3K R680 100

C661 OPEN

D664 TFZVTR4.7B

C632 OPEN

C631 OPEN

D663 OPEN R677 10K

R672 270 3.9 2.5 0 D662 SL431A-AT

R618 OPEN

D1007 MM5Z11B

D 0.7 Q1003 12.5 G AP18T10AGH-HF (SWITCHING) R1026 51 S 0.7 R1009 1 C1020 2200P R1010 1

IC651 OPEN

C662 OPEN

R673 OPEN

C660 0.22

IC601 OPEN

HOT

C1012 1

R683 R684 OPEN OPEN

R654 180

C666 0.22

R617 OPEN

BC603 BEAD

14 12.6 13 2.9

Q657A OPEN

R690 1.5

R612 5.6K

R616 OPEN

BC602 BEAD

Q657 OPEN

D652A OPEN

D652 OPEN

D608A OPEN

R611 0.36 /2W

C653 470/25V

R676 R678 R679 OPEN OPEN OPEN

13.0 C610 100P

R1001 470

TO LCD PANEL CN1001 ASSEMBLY 56.6 1 VLED 0.7 2 ILED

R1006 10K

Q658A OPEN C624 OPEN

R1030 C1017 1K 0.022 C1016 2200P

16 3.9 15 0.7

D610 HSC119

R623 10K

C652 470/25V

D623 MM5Z30B C623 4.7

R1018 OPEN

C1019 1

18 5.4 17 0

GND 10 0

R688 R689 OPEN OPEN

R613 180 R621 560

C1013 R1015 0.18/1W 1000P

Q659 OPEN

C606 820P /2KV

D607 OPEN

R1031 10

R692 OPEN

D607A TFZVTR27B

D1004 HSC119

R1017 OPEN

IC1001 BD9488F-GE2 LED BACKLIGHT DRIVER

R1007 100K

D650 SB3150BH D650A OPEN

D621 HSC119

R609 D609A RB520SM-30 100

Q1001 AP18T10AGH-HF 18.8 D (SWITCHING) G 8.2 R1019 200 0.1 S R1016 OPEN

Q650 KTC3875S -Y-RTK/P (RESET)

R691 OPEN R653 33K

0 Q621 KTC3875S -Y-RTK/P OVER VOLTAGE 0.4 PROTECT 0 R622 0 0

3.3 -3.1

C1018 100P/1KV

0 D658 OPEN

C650 OPEN D651 SB3150BH D651A OPEN

Q601 TK7P60W G (SWITCHING) 2.6

D657 R652 MM5Z11B 56K C656 R693 1/50V OPEN

BC601 BEAD 4

192.0 D

C1007 47/100V

6 C605 330 /200V BC604 BEAD

C1006 47/100V

D1002 OPEN

5.4 9 ADIM-P R1014 3K R1011 33K

T601 POWER TRANS

R614 470K R603 470K R604 470K

C1011 1/100V

C1010 1/100V

2.2 1 OVP 3.5 2 UVLO C1015 0.047 4.1 3 SS CONTROL R1012 LOGIC 56K 1.3 4 RT 2.7 5 VCC 2.7 6 VREG R1003 1K 3.3 7 FAIL DRIVE DETECT R1013 240K 0.7 8 ADIM DRIVE

R1028 9.1K R1029 9.1K

D655 SB3A0BH

JS604 R602 OPEN

D604 1N5406BH

R1020 240K

D1001 SK210TD

2.5A250V

D1006 TFZVTR30B

L1001 100uH

C1005 OPEN

GND

R601 1.2M/1/2W

F602 2.5A/250V

C611 OPEN

C1004 1

OUT

AC601 AC CORD

C1001 470/25V

POWER SUPPLY CBA

HOT CIRCUIT. BE CAREFUL.

NOTE: The voltage for parts in hot circuit is measured using hot GND as a common terminal.

CAUTION ! : For continued protection against risk of fire, replace only with same type 2.5A, 250V fuse. ATTENTION : Utiliser un fusible de rechange de même type de 2.5A, 250V.

C635 OPEN

R681 10K

C638 OPEN

R669 10K R668 47K

C639 OPEN

COLD

CN501 0 1 0 2 3.3 3 3.3 4 3.3 5 3.3 6 3.3 7 3.4 8 0 9 0 10 0 11 0 12 0 13 0 14 13.4 15 13.4 16 13.4 17 13.4 18 0 19 20.7 20 20.7 21 20.7 22 20.7 23

TO DIGITAL MAIN CBA UNIT CN3701 LED-CONT PROTECT1 PROTECT3 RESET BACKLIGHT-SW P-ON-H2 BACKLIGHT-ADJ AL+3.3V GND GND GND GND GND GND AMP+13V AMP+13V AMP+13V AMP+13V GND P-ON+21V P-ON+21V P-ON+21V P-ON+21V

UNLESS OTHERWISE SPECIFIED: DIODES ARE HSS4148TE-E.

D 10-3

G PL13.8ASCP

Power Supply Schematic Diagram [TYPE B] CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F602) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail.

2.5A 250V

C1002 470/25V

C1003 1

C1009 1/100V

CN601 W B C603 1000P/250V

SA601 VARISTOR C602 1000P/250V C604 0.22/275V C616 1000P/250V L601 LINE FILTER

R1027 22K JS602 OPEN

JS601 OPEN

SA602 GT601 OPEN OPEN

JS603 C614 0.22/275V

D601 1N5406BH

L602 LINE FILTER

JS605 OPEN

JS606 OPEN

D602 1N5406BH

D604 1N5406BH

R1023 3.9K

R1021 0

R1024 1.5K

R1022 10K

D655A OPEN D653 SB3A0BH

D1005 HSC119

D653A OPEN

D603 1N5406BH

C654 470/16V

C617 100P/250V

C655 470/16V D654 1ZB20BB

R663 OPEN

D654A OPEN

R664 OPEN

R665 OPEN

BC604 BEAD

R651 D656 RS1BJTD 1

8 9

0.1 S

C607 1800P

C608 0.022

2.6

Q602 2SC5344SY SWITCHING CONTROL 0.4

R608 1.5K

R606 330

R607 330

C651 470/25V

C623 4.7 C622 10

C624 OPEN

C621 OPEN

IC602 TLP781F ERROR VOLTAGE DET 13.0

C610 100P

C666 0.22 IC601 OPEN

C660 0.22 19.0 2.5 0 D660 SL431A-AT

R658 2.7K

4 3

HOT

12.8 12.8

R659 27K R660 3.9K

3.9

R666 0

R675 68K R674 0

R667 8.2K

GP003 EARTH PLATE

R1005 R1004 100K 10K

R685 R686 R687 OPEN OPEN OPEN

R670 270

R661 3.3K

0.6

D405 OPEN D406 OPEN

C664 OPEN

C633 OPEN C630 OPEN 3.4 Q656 KTC3875S-Y-RTK/P (+3.3V REG.)

C665 R682 0.1 0

D661 HSC119

0 Q653 KTC3875S-Y-RTK/P (SWITCHING) 0

R619 OPEN

GP002 EARTH PLATE

R1025 1K

Q658 2SA950-O (+3.3V REG.) 13.4 3.4

R671 270

C663 100/10V

R662 3.3K R680 100

C661 OPEN

D664 TFZVTR4.7B

C632 OPEN

C631 OPEN

D663 OPEN R677 10K

R672 270 3.9

2.5 0 D662 SL431A-AT

R618 OPEN

GP001 EARTH PLATE

IC651 OPEN

C662 OPEN

R673 OPEN

R657 3.9K

19.0

D1007 MM5Z11B

R683 R684 OPEN OPEN

R654 180

R655 180

R612 5.6K

R617 OPEN

BC603 BEAD

12 8.1 11 12.6

Q657A OPEN

R690 1.5 20.4

0.4

R616 OPEN

BC602 BEAD

Q657 OPEN

D652A OPEN

C609 0.068

C1012 1

D 0.7 Q1003 12.5 G AP18T10AGH-HF (SWITCHING) R1026 51 S 0.7 R1009 C1020 1 2200P R1010 1

R1006 10K

Q658A OPEN

R615 OPEN

D652 OPEN

R676 R678 R679 OPEN OPEN OPEN

3 D608 1ZB36BB

D608A OPEN

C653 470/25V

D623 MM5Z30B

D609A R609 RB520SM-30 100 R611 0.36 /2W

C652 470/25V

R613 180 R621 560

14 12.6 13 2.9

D610 HSC119

D607 OPEN

R1001 470

TO LCD PANEL CN1001 ASSEMBLY 56.6 1 VLED 0.7 2 ILED

Q659 OPEN

C606 820P /2KV

D621 HSC119

C1013 R1015 0.12/1W 1000P

GND 10 0

R688 R689 OPEN OPEN

D650A OPEN

R1031 10

R692 OPEN

D607A TFZVTR27B

Q621 KTC3875S -Y-RTK/P OVER VOLTAGE 0.4 PROTECT 0 R622 0 0

R1030 C1017 1K 0.022 C1016 2200P

16 3.9 15 0.7

R1007 100K

D650 SB3150BH

D605 MM5Z4V3B

D1004 HSC119

R1018 OPEN

C1019 1

18 5.4 17 0

Q650 KTC3875S -Y-RTK/P (RESET)

R691 OPEN R653 33K

R623 10K

Q1001 AP18T10AGH-HF 18.8 D (SWITCHING) G 8.2 R1019 0.1 S 200

0 D658 OPEN

C650 OPEN D651 SB3150BH D651A OPEN

Q601 TK7P60W G (SWITCHING) 2.6

3.3 -3.1

C656 R693 1/50V OPEN

BC601 BEAD 4

192.0 D

D657 R652 MM5Z11B 56K

C1018 100P/1KV

R1017 OPEN

IC1001 BD9488F-GE2 LED BACKLIGHT DRIVER

C605 330 /200V

R614 470K R603 470K R604 470K

C1007 47/100V

R1016 OPEN

5.4 9 ADIM-P R1014 5.6K R1011 33K

T601 POWER TRANS

C1006 47/100V

D1002 OPEN

2.2 1 OVP 3.5 2 UVLO C1015 0.047 4.1 3 SS CONTROL R1012 LOGIC 56K 1.3 4 RT 2.7 5 VCC 2.7 6 VREG R1003 1K 3.3 7 FAIL DRIVE DETECT R1013 240K 0.7 8 ADIM DRIVE

C1014 OPEN R1028 9.1K R1029 9.1K

D655 SB3A0BH

JS604 R602 OPEN

R1020 240K

D1001 SK210TD C1011 1/100V

C1010 1/100V

2.5A250V

D1006 TFZVTR30B

L1001 100uH

C1005 OPEN

OUT

R601 1.2M/1/2W

F602 2.5A/250V

C611 OPEN

C1004 1

GND

AC601 AC CORD

C1001 470/25V

POWER SUPPLY CBA

HOT CIRCUIT. BE CAREFUL.

NOTE: The voltage for parts in hot circuit is measured using hot GND as a common terminal.

CAUTION ! : For continued protection against risk of fire, replace only with same type 2.5A, 250V fuse. ATTENTION : Utiliser un fusible de rechange de même type de 2.5A, 250V.

C635 OPEN

R681 10K

C638 OPEN

R669 10K R668 47K

C639 OPEN

COLD

CN501 0 1 0 2 3.3 3 3.3 4 3.3 5 3.3 6 3.3 7 3.4 8 0 9 0 10 0 11 0 12 0 13 0 14 13.4 15 13.4 16 13.4 17 13.4 18 0 19 20.7 20 20.7 21 20.7 22 20.7 23

TO DIGITAL MAIN CBA UNIT CN3701 LED-CONT(NU) PROTECT1 PROTECT3 RESET BACKLIGHT-SW P-ON-H2 BACKLIGHT-ADJ AL+3.3V GND GND GND GND GND GND AMP+13V AMP+13V AMP+13V AMP+13V GND P-ON+21V P-ON+21V P-ON+21V P-ON+21V

UNLESS OTHERWISE SPECIFIED: DIODES ARE HSS4148TE-E.

D 10-4

G PL13.8BSCP

Function Schematic Diagram

FUNCTION CBA UNIT R4052 6.8K

C4054 0.1

R4060 OPEN R4053 1K

D4051 SMLE12WBC7W1HR POWER

2 GND

NU 5

3 VCC

NU 4

C4057 OPEN

VCC GND VOUT

R4059 OPEN

R4058 OPEN

R4056 OPEN

IC4051 OPEN NU 6 1 OUT R4057 OPEN

RS4051 RS-272 (REMOTE SENSOR)

R4055 OPEN

3 2 1 C4053 0.1

R4051 56 R4054 1K C4051 10

C4056 10

C4052 1000P

R4001 18K D4002 OPEN

SW4001 VOL DOWN

C4055 OPEN

R4002 8.2K SW4002 VOL UP

R4003 4.7K SW4003 CH DOWN

R4004 2.7K SW4004 CH UP

R4005 2.2K SW4005 MENU

CN4052 1 2 3 4 5 6 7 8 9

TO DIGITAL MAIN CBA UNIT CN3101 AL+3.3V P-ON+5V LIGHT LED1 REMOTE KEY-IN1 GND SCL(NU) SDA(NU)

CN4053 1 2 3 4 5 6 7 8 9

(NO CONNECTION) AL+3.3V P-ON+5V LIGHT LED1 REMOTE KEY-IN1 GND SCL(NU) SDA(NU)

R4006 2.2K SW4006 SOURCE

SW4007 POWER

D4001 MM5Z5V6B

C4002 0.1

UNLESS OTHERWISE SPECIFIED: SWITCHES ARE SKRMABE010.

C 10-5

FL13.8SCF

Digital Main 1 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section. R3085 OPEN

DIGITAL MAIN CBA UNIT

CN3601 1 2 3 4

(NO CONNECTION) GND NU NU NU

CN3602 1 2 3 4

R3047 OPEN

R3044 OPEN

R3046 OPEN

C3057 OPEN

C3058 R3039 OPEN OPEN

D3008 OPEN

R3048 OPEN

Q3007 OPEN

R3632 OPEN

C3000 OPEN D3624 OPEN R3037 OPEN

R3135 0

R3622 100 R3621 10K

C3628 OPEN

C3627 0.047 C3629 R3623 1000P 24K

D3623 IC3621 OPEN MP1472GJC452Z (SW+12V) 1 SS

BST 8

2 EN

IN 7

R3625 120K

R3631 OPEN

R3629 10K

R3624 1K

GND 5

R3626 10K

D3622 OPEN

D3621 OPEN

C3636 OPEN

C3635 4.7

C3624 0.1

C3623 OPEN

C3622 OPEN

C3621 4.7

R3035 OPEN R3524 OPEN

C3625 R3627 OPEN OPEN C3626 0.1 C3630 OPEN L3621 33uH R3628 OPEN

SW 6

3 COMP 4 FB

C3634 4.7

C3633 4.7

C3632 4.7

C3512 OPEN

R3028 OPEN

C3631 OPEN

R3162 OPEN R3161 OPEN R3129 OPEN

TO DIGITAL MAIN 2 IC3005(2/6)

C3161 OPEN

NU NU NU NU TP POL CPV OE OE2 STV NU

M16 M13 N14 N13 L13 M15 L16 L15 L14 M14 K15

3P 3P OPEN OPEN 3P 3P 3P 3P 3P 3P 3P 3P OPEN OPEN C3654 C3655 C3648 C3649 C3650 C3651 C3652 C3653 C3656 C3657 C3658 C3659 C3660 C3661

C3647 OPEN

C3646 OPEN

C3645 OPEN

R3644 R3645 R3641 R3642 R3643 R3646

R3038 OPEN

C3514 OPEN

CONTINUE DIGITAL 3 CELL-PWR-CTRL VCOM-PWM CN3006 (NO CONNECTION) 30 LCD+21V 29 LCD+21V 28 GND 27 VCOM-PWM 26 PWR-CTRL 25 P-ON+3.3V 24 GND 23 ML0(+) 22 ML0(-) 21 ML1(+) 20 ML1(-) 19 ML2(+) 18 ML2(-) 17 GND 16 MLCLK(+) 15 MLCLK(-) 14 GND 13 ML3(+) 12 ML3(-) 11 ML4(+) 10 ML4(-) 9 ML5(+) 8 ML5(-) 7 GND 6 TP 5 POL 4 CPV 3 OE1 2 OE2 1 STV

CN3001 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

R16 R15 P14 P13 N16 N15 P16 P15 T16 T15 R14 T14 R13 T13

LVDS TX

R3131 0

C3644 OPEN

*1 IC3005(1/6) R8A05011BG-U0 DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER

C3643 OPEN

R3130 OPEN

(NO CONNECTION) CN3014 LCD+12V 30 LCD+12V 29 LCD+12V 28 LCD+12V 27 GND 26 GND 25 GND 24 NU 23 SELLVDS 22 NU 21 GND 20 RX0(-) 19 RX0(+) 18 GND 17 RX1(-) 16 RX1(+) 15 GND 14 RX2(-) 13 RX2(+) 12 GND 11 RXCLK(-) 10 RXCLK(+) 9 GND 8 RX3(-) 7 RX3(+) 6 GND 5 BIST 4 NU 3 NU 2 GND 1 (NO CONNECTION) GND NU NU NU

R3045 OPEN

C3167 OPEN

OPEN OPEN OPEN OPEN OPEN OPEN

(NO CONNECTION) LCD+21V LCD+21V LCD+21V GND VCOM-PWM PWR-CTRL P-ON+3.3V GND ML0(+) ML0(-) ML1(+) ML1(-) ML2(+) ML2(-) GND MLCLK(+) MLCLK(-) GND ML3(+) ML3(-) ML4(+) ML4(-) ML5(+) ML5(-) GND TP POL CPV OE1 OE2 STV

OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN

C3166 OPEN

R3088 9.1K

C3666 C3662 C3663 C3664 C3665 C3667 R3041 R3117 R3118 R3119 R3120 R3132

R3630 OPEN

C3642 OPEN

CN3013 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

C3641 OPEN

TO LCD PANEL ASSEMBLY LCD+12V LCD+12V LCD+12V LCD+12V GND GND GND NU SELLVDS NU GND RX0(-) RX0(+) GND RX1(-) RX1(+) GND RX2(-) RX2(+) GND RXCLK(-) RXCLK(+) GND RX3(-) RX3(+) GND BIST NU NU GND

CONTINUE DIGITAL 4 P-ON+5V P-ON+21V P-ON+3.3V PROTECT3

D 10-6

F PL13.8SCD1

Digital Main 2 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section.

DIGITAL MAIN CBA UNIT

+3.3V

GND

SDA

SCL

IF-AGC

DIF-OUT1

DIF-OUT2

TU3901 (TUNER UNIT) IC3013 74LVC1G126GW (BUFFER GATE) 1 VCC 5

C3214 0.1

3 GND

Q3301 RU1L002SNTL (BUFFER)

C3903 0.1 C3902 0.1

C3905 10

C3901 220/6.3V

IC3014 74LVC1G126GW (BUFFER GATE) 1 VCC 5

L3913 2.2uH D3901 MM5Z5V6B

C3934 OPEN

C3909 OPEN

C3910 1000P

C3175 33P

C3176 33P

R3204 2.7K

D3902 MM5Z5V6B

3 GND

R3203 2.7K R3331 10

D3904 MM5Z5V6B

R3332 10

*1 IC3005(2/6) R8A05011BG-U0 DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER

SCL R12 SDA T12 B12

R3206 47 R3207 47

DEMODULATOR /MPEG DECODER

C3173 33P

R3251 10

C3172 33P

R3250 10

R3333 10

A12

IF-AGC A16

R3194 1K

R3202 2.7K R3205 18K

HSYNC A14 VSYNC B14 A9 C7 C11 SW

A/D CONVERTER

2 DIGITAL SIGNAL PROCESS

NU NU NU NU

C10 C9 D8 B11 A10 C8 B9 D9

C3178 0.1

C3177 1

R3339 OPEN

D3041 OPEN

D3054 OPEN

C3291 33P

0.01 0.1 0.1 0.1

C3292 33P

C3293 33P

JK3001 PC-RGB-IN

R3358 10K

D3050 OPEN

R3347 10K

D3045 OPEN

15 10

D3049 OPEN D3053 OPEN R3356 75

R3377 75

R3364 75

R3298 OPEN

R3296 OPEN

D3055 OPEN

R3327 10 R3328 10 R3329 10 C3289 33P

C3288 33P

C3287 33P

CONTINUE DIGITAL 3 COMP-DET R3302 75

R3303 75

R3301 75 JK3702

TO DIGITAL MAIN 3 IC3005(3/6)

C3708 0.1

R3711 10K

TO DIGITAL MAIN 3 IC3005(3/6)

NU B10 NU A11 NU D10

R3321 4.7K

R3285 47 R3286 47 R3284 47

R3701 OPEN R3702 OPEN

R3710 100 C3707 1

TO DIGITAL TO DIGITAL MAIN 6 MAIN 1 IC3005(6/6) IC3005(1/6)

R3326 4.7K

R3343 OPEN

R3334 10

C3194 0.1 C3195 0.1 C3196 0.1 C3198 C3199 C3200 C3201

CONTINUE DIGITAL 6 VGA-SDA VGA-SCL

CONTINUE DIGITAL 4 P-ON+3.3V P-ON+5V

D3903 MM5Z5V6B

TO DIGITAL MAIN 5 IC3005(5/6)

Q3302 RU1L002SNTL (BUFFER)

C3335 2.2

R3712 10K

R3703 OPEN

Q3701 2SC4081UBTLQ (BUFFER) R3709 220

C3285 0.1 C3286 0.1 C3336 1

C3706 1 R3708 110

COMPONENT -Y/VIDEO-IN COMPONENT -Pb-IN COMPONENT -Pr-IN JK3701 DIGITAL AUDIO-OUT (COAXIAL)

C3709 100P R3704 100K R3705 100K

AUDIO(L)-IN

AUDIO(R)-IN CONTINUE DIGITAL 5 SCL SDA AUDIO(L)-IN AUDIO(R)-IN CONTINUE DIGITAL 5 SPDIF

J 10-7

L PL13.8SCD2

Digital Main 3 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section.

C3009 OPEN

4 IC3002 K4T51163QJ-BCE7 (DDR2 SDRAM) C3029 C3030 C3031 C3032 C3033 C3034 C3035 C3037 C3038 C3039 C3040 C3041 C3140

0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1

*A VDD VREF J2 C3010 0.1

1-O3 2-O3 3-O3 SD-DQ15 SD-DQ12 SD-DQ10 SD-DQ9 SD-DQ14 SD-DQ13 SD-DQ11 SD-DQ8

3 4-O3 5-O3 6-O3

SD-DQ3 SD-DQ2 SD-DQ7 SD-DQ6 SD-DQ4 SD-DQ1 SD-DQ5 SD-DQ0

E2 A2 R8 R7 R3

NU NU NU NU NU

B7 A8 B3 B9 B1 D9 D1 D3 D7 C2 C8 F7 E8 F3 F9 F1 H9 H1 H3 H7 G2 G8

UDQS UDQS/NU UDM DQ15 DQ12 DQ10 DQ9 DQ14 DQ13 DQ11 DQ8 LDQS LDQS/NU LDM DQ3 DQ2 DQ7 DQ6 DQ4 DQ1 DQ5 DQ0

CKE CK CK CS RAS CAS WE BA2/NU BA1 BA0 A12 A11 A10/AP A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 ODT

K2 J8 K8 L8 K7 L7 K3 L1 L3 L2 R2 P7 M2 P3 P8 P2 N7 N3 N8 N2 M7 M3 M8 K9

R3083 100

R3049 150

IC3006 W25Q32FVSSIG (MEMORY) 1 CS

VCC 8

2 SO

NU 7

3 WP

SCK 6

4 GND

SI 5

CN3009 1 2 3 4

C3246 1

L3025 EXC24CG900U

R3065 100

C3051 0.1

SD-DQ15 SD-DQ14 SD-DQ13 SD-DQ12 SD-DQ11 SD-DQ10 SD-DQ9 SD-DQ8 SD-DQ7 SD-DQ6 SD-DQ5 SD-DQ4 SD-DQ3 SD-DQ2 SD-DQ1 SD-DQ0

33x4

R3031

33x4

R3032

33x4

VSS *B

R3033

R3034

C3073 0.1

R3479 10K

(USB JACK) BUS-POWER USBDN USBDP GND

C3050 0.1

R3030

R3102 10K R3107 10K

R3064 100

3-M3 6-M3 2-M3 1-M3 5-M3 4-M3

*A:A1,A9,C1,C3,C7,C9,E1,E9, G1,G3,G7,G9,J1,J9,M9,R1 *B:A3,A7,B2,B8,D2,D8,E3,E7, F2,F8,H2,H8,J3,J7,N1,P9

*1 IC3005(3/6) R8A05011BG-U0 DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER

R3082 100

C3348 220/6.3V

33x4

R3016 R3084 R3087 R3070

33 10 10 150

R3089 R3092 R3093 R3094 R3095

47 47 47 47 22

R3099 5.6K

C3184 18P

M5 SD-VREF0 N3 GND XIN25 H15 XOUT25 H16 R8 N8 P7 R6 P6 N7 T5 P8 P4 T3 R4 T2 P3 T4 R3 N4 T6 R5 T7 R7 N5 P5

SD-DQ15 SD-DQ14 SD-DQ13 SD-DQ12 SD-DQ11 SD-DQ10 SD-DQ9 SD-DQ8 SD-DQ7 SD-DQ6 SD-DQ5 SD-DQ4 SD-DQ3 SD-DQ2 SD-DQ1 SD-DQ0 SD-UDM SD-LDM SD-UDQSN SD-UDQS SD-LDQSN SD-LDQS

H1 H3 J2 J1 J4 L1 K4 L2 L4 N2 P1 M3 M1 M2 L3 N1 J3 K3 K1 K2 H2 R2 R1 H4

SD-A4 SD-CAS SD-A11 SD-A0 SD-A10 SD-A1 SD-BA1 SD-A9 SD-WE SD-BA0 SD-BA2 SD-A3 SD-A5 SD-A12 SD-CKE SD-A7 SD-RAS SD-A6 SD-A2 SD-ODT SD-A8 SD-CLK SD-CLKN NU

P12 R11 P11 T11 T9 R9 R10 T10 P10

CS SOUT SIN SCK VBUS-EN VBUS-ST USBDP USBDN NU

ASEBRKAK-N ASEMD0 TRST-N TCK TDI TDO TMS TO DIGITAL MAIN 2 IC3005(2/6)

F15 F16 E16 E15 D16 D15 E14

R3223 1K

X3001 25MHz

C3183 20P

R3527 OPEN R3525 OPEN R3526 OPEN

R3522 10K R3395 4.7K

TXD0 G15 RXD0 G16

R3468 100 R3469 100 C3254 OPEN

BACKLIGHT-ADJ F3 VCOM-PWM F2 GND J14

CELL-PWR-CTRL D1 GPY10 E13 P-ON-H2 B16 HP-MUTE G13 BACKLIGHT-SW E2

C3255 OPEN

CN3010 1 2 3 C3253 4 OPEN

(NO CONNECTION) P-ON+5V UART0-TX UART0-RX GND

CONTINUE DIGITAL 5 CPU-RESET-N

R3511 22

CONTINUE DIGITAL 4 GPY10 CPU-RESET-N P-ON-H2 BACKLIGHT-ADJ BACKLIGHT-SW

100 22 22

R3503 10K TO DIGITAL MAIN 2 IC3005(2/6)

(NO CONNECTION) AL+3.3V GND ASEBRKAK-N ASEMD0 TRST-N TCK TDI TDO TMS CPU-RESET-N

CONTINUE DIGITAL 2 COMP-DET

R3516 100 R3517 OPEN

R3211 R3233 R3188

R3396 4.7K

CN3012 1 2 3 4 5 6 7 8 9 10

CONTINUE DIGITAL 1 CELL-PWR-CTRL VCOM-PWM

R3510 22K

LED1 D14 REMOTE C14 AUDIO-MUTE C1

CONTINUE DIGITAL 5 LED1 REMOTE

R3515 4.7K R3213 22 R3217 22 R3234 OPEN

COMP-DET N12

NU H14

R3215

R3201 33K

CONTINUE DIGITAL 4 P-ON+1.8V P-ON+3.3V AL+3.3V P-ON+5V

CONTINUE DIGITAL 5 HP-MUTE AUDIO-MUTE BACKLIGHT-SW

C3072 10

IC3019 AP2151WG-7 (HIGH SIDE SW) 1 OUT IN 5 2 GND

C3327 1

3 /FLAG RN 4 R3480 10K

DIGITAL MAIN CBA UNIT

P 10-8

R PL13.8SCD3

Digital Main 4 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section.

*1 IC3005(4/6) R8A05011BG-U0 DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER

R3222 10K

L3027 BEAD R3106 47K

G L3030 0 C3181 0.1

Q3013 SSM3K309T (SW+12V)

C3127 1

C3124 1 C3128 1

C3125 1 C3129 1

C3126 1 C3130 1

C3132 10

C3133 10

C3134 1

R3228 OPEN

C3118 10

C3136 1

C3114 10

C3115 10

C3139 0.1

AVDD33 AVDD33 AVDD33 AVDD33

H5 J5 M4 T1 M6 N6 M7 M8

C3609 1

R3608 4.7K

VDDCLK G11

VCCQ18 VCCQ18 VCCQ18 VCCQ18 VCCQ18 VCCQ18 VCCQ18 VCCQ18

3 CE

C3326 10

C3325 OPEN

C3324 OPEN

C3343 10

C3264 OPEN

C3322 10

C3321 OPEN

C3320 10

C3319 10

C3318 10

C3141 1

C3142 1

C3143 1

C3144 1

C3145 1

C3080 4.7

C3103 OPEN

C3148 1

C3149 10

C3150 1

C3007 0.1

R3133 10K C3090 1

C3088 R3137 4700P 2.7K

L3026 BEAD

C3151 1

C3152 1

C3154 1

VCCQ33 VCCQ33 VCCQ33 VCCQ33 VCCQ33 AVDD33

G4 F5 L12 K13 J12 N11

C3156 1

C3157 1

C3158 1

C3099 OPEN

R3142 OPEN

D3006 PTZTE255.1B

C3022 4.7

C3028 0.047 R3098 0 C3121 OPEN

C3043 R3005 4700P 4.3K

IN 7

3 COMP

SW 6

R3149 3.9K R3145 1.2K

C3094 330/4V

L3003 OPEN

C3075 0.022 R3103 1.8K C3087 10

C3102 4.7

C3002 OPEN

C3003 0.1

R3091 0

C3085 0.1

C3119 OPEN

C3017 R3001 2200P 8.2K

GND 5 C3096 10

C3097 OPEN

C3001 0.1

1 SS

3 GND

NU 6

4 NU

EN 5

C3069 10

CONTINUE DIGITAL 5 P-ON+3.3V CHECK+1.8V AL+3.3V P-ON+5V P-ON+3.3V(1) AMP+13V

IC3001 MP1472GJC452Z (+3.3V REG.) BST 8

1 SS 2 EN

IN 7

3 COMP

C3092 OPEN R3057 OPEN

2 EN

IN 7

3 COMP

SW 6

R3602 OPEN C3606 OPEN

D3005 PTZTE255.1B

R3004 33K R3003 6.2K

SW 6 GND 5

C3020 330/4V

C3021 10

C3059 R3014 10 270

C3056 10

C3074 10

C3053 OPEN

R3601 OPEN C3605 OPEN

D3994 OPEN D3995 OPEN D3107 HSC119 R3140 18K

R3112 10K C3042 0.1

R3115 Q3103 OPEN 2SA1576UBTLQ (SWITCHING)

Q3102 2SC4081UBTLQ (SWITCHING)

L3005 22uH

GND 5

CONTINUE DIGITAL 3 GPY10 CPU-RESET-N P-ON-H2 BACKLIGHT-ADJ BACKLIGHT-SW

C3014 0.1

L3002 33uH

D3112 MM5Z12B

R3108 47K

C3095 OPEN R3054 OPEN

C3068 OPEN

R3002 15K

C3105 OPEN

BST 8

CONTINUE DIGITAL 5 RESET PROTECT1 PROTECT3

VCC 8 NU 7

4 FB

C3065 10

R3113 10K

R3101 1K

R3603 OPEN C3607 OPEN

C3238 R3139 OPEN 1K

Q3009 2SC4081UBTLQ (SWITCHING)

C3107 R3104 1 1K

R3114 47K

C3063 OPEN

C3994 OPEN

C3604 10

C3603 1

D3602 MM5Z5V6B

R3051 100

D3007 OPEN

R3006 10K

C3995 OPEN

C3996 OPEN

DIGITAL MAIN CBA UNIT

V 10-9

CONTINUE DIGITAL 6 P-ON+3.3V AL+3.3V P-ON+3.3V(1) P-ON+5V CONTINUE DIGITAL 2 P-ON+3.3V P-ON+5V CONTINUE DIGITAL 1 P-ON+5V P-ON+21V P-ON+3.3V PROTECT3

IC3007 BD00IC0WEFJ (+1.8V REG.)

C3079 220/6.3V

R3143 15K

IC3003 MP1472GJC452Z (+5V REG.)

4 FB R3012 33K R3007 12K

EN 5

C3159 1

VSS *D *C:G5,G6,H6,J7,J11,J13,K6,K7, K11,L8,L9,M9,M11,N9,P9. *D:D2~D5,D12,E3~E5,E7,E9,F4,F6, F7,F10,F11,G7~G10,H7~H13,J6, J8~J10,K5,K8~K10,K12,L5~L7, L10,L11,P2,T8

NU 6

4 NU

R3008 1

2 FB R3110 10K R3109 3.3K

C3024 10

NU 7

C3131 1

Q3004 2SC4081UBTLQ (SWITCHING)

R3111 10K

VCC 8

3 GND

L3009 10uH

D3114 MM5Z5V6B

AVDD33 E6 C3155 1

C3086 10

1 VOUT D3106 HSC119

C3091 OPEN R3141 OPEN

AVDD33 D6 L3006 BEAD

R3043 180

C3013 0.047

BST 8

2 EN

4 FB

C3019 0.022 R3062 1.8K

C3610 1

IC3008 MP1472GJC452Z (+1.2V REG.) 1 SS

Q3003 2SC4081UBTLQ (SWITCHING)

R3060 2.7K R3059 2.7K

NU 4 R3607 OPEN

C3083 0.015

D3113 MM5Z5V6B

R3079 10K R3606 OPEN

2 GND

C3611 R3609 OPEN OPEN

L3019 OPEN

E10 C2 C3 E11

D3104 HSC119

IC3601 AP2121AK-3.3TRE1 (+3.3V REG.) 1 VIN VOUT 5

R3605 0

1 VOUT

D3115 HSC119

R3086 4.7K R3077 10K

L3021 BEAD

IC3004 BD00IA5WEFJ-E2 (+1.2V REG.)

R3061 10K

C3237 R3227 OPEN OPEN

C3135 0.1

R3036 100

D3103 HSC119 R3424 100

2 FB

Q3011 OPEN

AVDD12 M10

AVDD12 E8 AVDD12 F8 AVDD12 F9

C3265 R3138 10 OPEN R3423 R3097 47K 1.5K

Q3005 2SC4081UBTLQ (SWITCHING) D3101 HSC119 D3102 HSC119

VDD12 *C C3123 1

Q3101 2SC4081UBTLQ (SWITCHING)

R3105 10K

Q3006 2SA1576UBTLQ (SWITCHING)

D3105 OPEN

R3013 R3011 R3009 R3072 R3068

VDD12STB E12

R3100 22K

220 OPEN 100 100 100

C3160 0.1

OPEN OPEN OPEN OPEN OPEN OPEN

VCC33STB F12 VCC33STB G12

C3062 C3008 C3006 C3004 C3055 C3048

CONTINUE DIGITAL 3 P-ON+1.8V P-ON+3.3V AL+3.3V P-ON+5V

R3221 100

CN3701 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23

TO POWER SUPPLY CBA CN501 NU PROTECT1 PROTECT3 RESET BACKLIGHT-SW P-ON-H2 BACKLIGHT-ADJ AL+3.3V GND GND GND GND GND GND AMP+13V AMP+13V AMP+13V AMP+13V GND P-ON+21V P-ON+21V P-ON+21V P-ON+21V

X PL13.8SCD4

Digital Main 5 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section. CONTINUE DIGITAL 4 P-ON+3.3V CHECK+1.8V AL+3.3V P-ON+5V P-ON+3.3V(1) AMP+13V CONTINUE DIGITAL 3 LED1 REMOTE CN3101 1 2 3 4 5 6 7 8 9

C3559 OPEN

C3553 OPEN

R3320 OPEN

C3555 OPEN R3551 100

R3555 OPEN

R3183 OPEN

C3556 OPEN

Q3010 OPEN

C3558 OPEN

R3553 100

R3401 0

D3201 MM5Z5V6B

R3184 OPEN

D3501 MM5Z5V6B

R3314 R3315 R3316 C3231

A15 B13 A13 C13 C12

22 OPEN 22 0.22

C3328 OPEN

C3217 C3218 C3223 C3224

2.2 2.2 1 1

D3111 MM5Z5V6B

KEY-IN1 PROTECT3 LIGHT-SENS PROTECT1 LPF TO DIGITAL TO DIGITAL MAIN 2 MAIN 6 IC3005(2/6) IC3005(6/6)

A8 B8 B7 A7

CONTINUE DIGITAL 3 CPU-RESET-N

R3191 100

RESET J15

R3186 OPEN

R3862 10K

R3995 10K

R3216 100

CONTINUE DIGITAL 6 HPD-SINK PWR

R3219 22

HP-DET K16

C3329 0.01

R3335 18K R3336 18K

CONTINUE DIGITAL 3 HP-MUTE AUDIO-MUTE BACKLIGHT-SW

R3402 0

R3185 OPEN

R3557 10

SCL SDA AUDIO(L)-IN AUDIO(R)-IN

R3210 100

R3220 33K

OPEN OPEN OPEN OPEN 1000P 1000P

R3556 10

HPD-SINK K14 PWR J16

Q3501 2SC4081UBTLQ (LED DRIVE)

CONTINUE DIGITAL 4 RESET PROTECT1 PROTECT3 CONTINUE DIGITAL 2

NU G1 NU E1 NU G2

D13 CHECK+1.8V

R3560 100K

C3554 C3560 220 1 /6.3V C3551 33P C3552 33P

R3312 10K

R3318 22K R3317 10K R3319 10K

TO FUNCTION CBA UNIT CN4052 SDA(NU) SCL(NU) GND KEY-IN1 REMOTE LED1 LIGHT P-ON+5V AL+3.3V

R3558 OPEN

R3552 100

Q3502 2SA1576UBTLQ (LED DRIVE) R3559 10K

C3229 R3502 C3227 R3501 C3233 C3232

*1 IC3005(5/6) R8A05011BG-U0 DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER

R3178 220

NU NU NU NU NU NU

AUDIO I/F

D11 D7 C6 C5 B6 A6 N10

R3340 C3219 C3220 C3216

10K 10 10 10

IC3009 PST8429UR (RESET) 1 GND OUT 4 2 VDD

D3108 OPEN

R3182 56K C3116 1000P

CD 3

C3106 1

C3113 0.033

CONTINUE DIGITAL 2 SPDIF

R3209 100 R3865 10K

R3561 10 R3809 OPEN

R3810 OPEN

R3864 1K

C3825 1

R3814 OPEN

R3870 220

Q3803 2SA1576UBTLQ (SWITCHING)

R3818 10K

R3813 OPEN

R3817 10K C3870 2200P

R3816 1.8K

R3819 100K C3808 1

C3992 1

R3815 47K

Q3802 2SC4081UBTLQ (SWITCHING)

POWER LIMIT

4 5

R3806 0

C3815 R3807 OPEN 1 C3816 1 C3817 1 Q3804 OPEN

PWM LOGIC

C3819 1 R3871 220

C3809 1 C3871 2200P

R3823 OPEN

22 21

9 GVDD

C3861 0.1

BIAS VCC 6 7 8

C3852 1

C3854 220/6.3V C3855 1000P

R3854 OPEN C3828 1

C3859 0.1

L3801 10uH

C3802 0.22 C3803 0.22

20 GND 19 POWER LIMIT

2 1 MUTE

JK3703 HEADPHONE JACK

R3856 10K

C3857 47/25V

R3855 10K

C3858 100/16V

5 R3852 15K

C3801 0.22

DRIVE

C3856 1000P IC3851 BH3547F (HEADPHONE AMP)

Q3862 OPEN

C3832 10

C3862 OPEN

C3853 220/6.3V 4 GND

25 GND 24

GAIN CONTROL

R3866 100K

R3853 OPEN

DRIVE

8 GND R3808 10K

C3851 1

Q3861 2SC4081UBTLQ (SWITCHING)

PVCCL 27

DRIVE

Q3801 2SC4081UBTLQ (SWITCHING)

R3851 15K

C3860 0.1

R3863 OPEN

PVCCL 28

7 AVCC R3812 10K

R3868 OPEN

R3869 OPEN

CONTROL LOGIC

R3811 0

R3805 10K

C3824 1000P

IC3801 TPA3110D2PWPR (AUDIO AMP)

R3822 10 1

C3993 0.1

R3861 10K

R3867 0

PWM LOGIC

C3827 1000P

C3833 OPEN

18 DRIVE 17

13 NU

PVCCR 16

14 PBTL

PVCCR 15

C3804 0.22

C3831 100/16V

C3826 100/16V

C3829 100/16V

R3801 OPEN C3807 OPEN L3802 10uH

C3811 1000P

C3820 D3801 1 OPEN

R3802 OPEN C3805 OPEN L3803 10uH

C3812 1000P

C3821 D3802 1 OPEN

R3803 OPEN C3806 OPEN L3804 10uH

C3813 1000P

C3822 D3803 1 OPEN

R3804 OPEN C3810 OPEN

C3814 1000P

C3823 D3804 1 OPEN

CN3801 1 2 3 4

SP(L)+ SP(L)SP(R)SP(R)+

SP3801 SPEAKER L-CH

SP3802 SPEAKER R-CH

DIGITAL MAIN CBA UNIT

BB 10-10

DD PL13.8SCD5

Digital Main 6 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section.

CONTINUE DIGITAL 4 P-ON+3.3V AL+3.3V P-ON+3.3V(1) P-ON+5V

C3316 10 D3993 OPEN

C3424 OPEN

C3427 OPEN

R3405 100 R3415 82K

R3486 3.9K

D3057 RB751S-40 R3237 27K

HDMI-CEC B15

HDMI I/F

C3987 OPEN

C3988 OPEN

R3489 10K

VCC 61

VCC 55

28 GND

SCL-SINK C16

29 SCL-SINK

SDA-SINK C15

30 SDA-SINK

33 HDMI-SEL1 F1

C3204 OPEN

R3212 47K

R3236 560

R3010 1K

C3185 0.01

R3270 2.2K

C3187 2.2

R3991 10K

C3188 2200P

PWR M12 R3193 4.7K

HDMI-SCL G14 HDMI-SDA F14

D3003 RB751S-40

R3192 4.7K C3206 OPEN

CONTINUE DIGITAL 5 HPD-SINK PWR

C3207 OPEN

CONTINUE DIGITAL 2 VGA-SDA VGA-SCL R3451 10K

R3453 1.5K

1 VCC1

VCC2 16

2 SCL1

SCL2 15

3 SDA1

SDA2 14

4 WPB C3192 0.1

R3452 10K

R3281 100

Q3451 2SC4081UBTLQ (SWITCHING)

R3282 100

DIGITAL MAIN CBA UNIT

5 VCC-OUT

D3001 RB751S-40

D3002 RB751S-40 R3022 10K

SDA3 11 SCL3 10

8 VCC0

VCC3 9

R3276 47K C3018 R3040 0.1 2.7K

R3029 1K

JK3004 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19

HDMICONNECTOR-1 TMDS-D2(+) D-SHIELD0 TMDS-D2(-) TMDS-D1(+) D-SHIELD1 TMDS-D1(-) TMDS-D0(+) D-SHIELD2 TMDS-D0(-) TMDS-CLOCK(+) C-SHIELD0 TMDS-CLOCK(-) HDMI-CEC NU HDMI-CLOCK HDMI-DATA GND +5V HOT PLUG DETECT

R3025 1K

Q3002 2SC4081UBTLQ (SWITCHING) R3027 10K

R3073 0 R3074 0 R3075 0 R3076 0 R3081 0

NU 13

7 SCL0

R3273 47K

R3024 10K

GND 12

6 SDA0

C3208 OPEN

R3023 22K

IC3011 BU9883FV-WE2 (HDMI SERIAL EEPROM)

HDMICONNECTOR-3 TMDS-D2(+) D-SHIELD0 TMDS-D2(-) TMDS-D1(+) D-SHIELD1 TMDS-D1(-) TMDS-D0(+) D-SHIELD2 TMDS-D0(-) TMDS-CLOCK(+) C-SHIELD0 TMDS-CLOCK(-) HDMI-CEC NU HDMI-CLOCK HDMI-DATA GND +5V HOT PLUG DETECT

R3017 10K

R3992 0

C3186 4700P R3271 3K

JK3003 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19

Q3001 2SC4081UBTLQ (SWITCHING)

R3018 1K

R3509 22

R3990 OPEN

R3214 47K

C3005 R3019 0.1 2.7K

R3497 4.7K

EXT-RES C4 PLL-XFC-A B5 PLL-XFC-P A5

C3205 OPEN

VCC

R3496 4.7K

HOT-PLUG- 50 DETECT2 NU 49

GND

R3994 OPEN

31 HOT-PLUGDETECT-SINK 32 HDMISEL0

VCC

HDMI-SEL0 G3

R3514 100 R3508 22

HOT-PLUGDETECT1

HPD-SINK F13

R3487 4.7K

HDMISEL1 NU

R3488 4.7K

HDMICONNECTOR-2 TMDS-D2(+) D-SHIELD0 TMDS-D2(-) TMDS-D1(+) D-SHIELD1 TMDS-D1(-) TMDS-D0(+) D-SHIELD2 TMDS-D0(-) TMDS-CLOCK(+) C-SHIELD0 TMDS-CLOCK(-) HDMI-CEC NU HDMI-CLOCK HDMI-DATA GND +5V HOT PLUG DETECT

R3058 10K

JK3002 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19

Q3008 2SC4081UBTLQ (SWITCHING)

R3063 1K

HDMI SW

25 VCC

C3990 1P

R3055 1K

GND 58

24 C3984 OPEN

R3278 47K

22 GND 23

C3985 OPEN

R3275 47K

C3203 OPEN

19 VCC

C3986 OPEN

C3202 OPEN

C3023 R3066 0.1 2.7K

18 C3989 OPEN

IC3018 TMDS351PAGR (HDMI SW)

HOT-PLUG- 64 DETECT3 63

B1 A1 B2 A2 B3 A3 B4 A4

GND

AUDIO DECODER

C3422 OPEN

VCC

VIDEO DECODER

C3420 OPEN

GND

TO DIGITAL MAIN 5 IC3005(5/6)

C3426 1

VCC

TO DIGITAL MAIN 2 IC3005(2/6)

Q3014 RU1L002SNTL (BUFFER)

C3425 1

*1 IC3005(6/6) R8A05011BG-U0 DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER

C3423 1

GND

C3421 1

R3078 OPEN R3080 OPEN

C3191 0.1

HH 10-11

JJ FL13.8SACD6

Digital Main 1 Schematic Diagram [TYPE B] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section.

(NO CONNECTION) GND NU NU NU

CN3602 1 2 3 4

R3046 12K

C3057 47/25V

C3058 R3039 OPEN 0.1

R3048 1K C3000 OPEN

D3624 OPEN R3037 OPEN

R3135 OPEN

R3622 OPEN R3621 OPEN

C3628 OPEN

C3627 OPEN C3629 R3623 OPEN OPEN

D3623 OPEN

IC3621 OPEN 1 SS

BST 8

2 EN

IN 7

3 COMP

R3625 OPEN

R3631 OPEN

R3629 OPEN

R3624 OPEN

GND 5

R3626 OPEN

D3622 OPEN

D3621 OPEN

C3636 OPEN

C3635 OPEN

C3623 OPEN

C3622 OPEN

C3621 OPEN

R3035 0 R3524 10K

C3625 R3627 OPEN OPEN C3626 OPEN C3630 L3621 OPEN OPEN R3628 OPEN

SW 6

4 FB

C3624 OPEN

C3634 OPEN

C3633 4.7

C3632 4.7

C3512 OPEN

R3028 0

C3631 OPEN

R3162 OPEN R3161 OPEN R3129 OPEN

TO DIGITAL MAIN 2 IC3005(2/6)

C3161 OPEN

NU NU NU NU TP POL CPV OE OE2 STV NU

M16 M13 N14 N13 L13 M15 L16 L15 L14 M14 K15

C3654 C3655 C3648 C3649 C3650 C3651 C3652 C3653 C3656 C3657 C3658 C3659 C3660 C3661

OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN

C3647 OPEN

C3646 OPEN

C3645 OPEN

R3644 R3645 R3641 R3642 R3643 R3646

C3514 1000P

CN3001 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

R16 R15 P14 P13 N16 N15 P16 P15 T16 T15 R14 T14 R13 T13

LVDS TX

R3131 OPEN

C3644 OPEN

*1 IC3005(1/6) R8A05011BG-U0 DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER

C3643 OPEN

R3130 OPEN

R3038 OPEN

100 100 100 100 100 100

OPEN 100P OPEN OPEN OPEN OPEN 100K 100K 100K 100K 100K 100K

CN3601 1 2 3 4

R3047 3.9K

R3044 11K

Q3007 2SC4081UBTLQ (SWITCHING)

R3632 OPEN

R3045 18K

C3167 OPEN

R3088 4.3K

C3666 C3662 C3663 C3664 C3665 C3667 R3041 R3117 R3118 R3119 R3120 R3132

C3166 OPEN

C3642 OPEN

R3630 7.5

C3641 OPEN

(NO CONNECTION) CN3013 LCD+12V 1 LCD+12V 2 LCD+12V 3 LCD+12V 4 GND 5 GND 6 GND 7 NU 8 SELLVDS 9 NU 10 GND 11 RX0(-) 12 RX0(+) 13 GND 14 RX1(-) 15 RX1(+) 16 GND 17 RX2(-) 18 RX2(+) 19 GND 20 RXCLK(-) 21 RXCLK(+) 22 GND 23 RX3(-) 24 RX3(+) 25 GND 26 BIST 27 NU 28 NU 29 GND 30

CONTINUE DIGITAL 4 P-ON+5V P-ON+21V P-ON+3.3V PROTECT3 D3008 CONTINUE OPEN DIGITAL 3 CELL-PWR-CTRL VCOM-PWM TO LCD PANEL CN3006 ASSEMBLY 30 LCD+21V 29 LCD+21V 28 GND 27 VCOM-PWM 26 PWR-CTRL 25 P-ON+3.3V 24 GND 23 ML0(+) 22 ML0(-) 21 ML1(+) 20 ML1(-) 19 ML2(+) 18 ML2(-) 17 GND 16 MLCLK(+) 15 MLCLK(-) 14 GND 13 ML3(+) 12 ML3(-) 11 ML4(+) 10 ML4(-) 9 ML5(+) 8 ML5(-) 7 GND 6 TP 5 POL 4 CPV 3 OE1 2 OE2 1 STV

R3085 OPEN

DIGITAL MAIN CBA UNIT

D 10-12

F PL13.8BSCD1

Digital Main 2 Schematic Diagram [TYPE B] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section.

DIGITAL MAIN CBA UNIT

+3.3V

GND

SDA

SCL

IF-AGC

DIF-OUT1

DIF-OUT2

TU3901 (TUNER UNIT) IC3013 74LVC1G126GW (BUFFER GATE) 1 VCC 5

C3214 0.1

3 GND

Q3301 RU1L002SNTL (BUFFER)

C3905 10

C3901 220/6.3V

IC3014 74LVC1G126GW (BUFFER GATE) 1 VCC 5

L3913 2.2uH D3901 MM5Z5V6B

C3909 OPEN

C3934 OPEN

C3910 1000P

C3175 33P

C3176 33P

R3204 2.7K

D3902 MM5Z5V6B

3 GND

R3203 2.7K R3331 10

D3904 MM5Z5V6B

R3332 10

*1 IC3005(2/6) R8A05011BG-U0 DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER SCL R12 SDA T12 B12

TO DIGITAL MAIN 5 IC3005(5/6)

R3206 47 R3207 47

DEMODULATOR /MPEG DECODER

C3173 33P

R3251 10

C3172 33P

R3250 10

R3333 10

A12

IF-AGC A16

R3194 1K

R3202 2.7K R3205 18K

HSYNC A14 VSYNC B14 A9 C7 C11 SW

A/D CONVERTER

2 DIGITAL SIGNAL PROCESS

NU NU NU NU

C10 C9 D8 B11 A10 C8 B9 D9

C3178 0.1

C3177 1

R3339 OPEN

D3041 OPEN

D3054 OPEN

C3291 33P

0.01 0.1 0.1 0.1

C3292 33P

C3293 33P

JK3001 PC-RGB-IN

R3358 10K

D3050 OPEN

R3347 10K

D3045 OPEN

15 10

D3049 OPEN D3053 OPEN R3356 75

R3377 75

R3364 75

R3298 OPEN

R3296 OPEN

D3055 OPEN

R3327 10 R3328 10 R3329 10 C3289 33P

C3288 33P

C3287 33P

CONTINUE DIGITAL 3 COMP-DET R3302 75

R3303 75

R3301 75 JK3702

TO DIGITAL MAIN 3 IC3005(3/6)

C3708 0.1

R3711 10K

TO DIGITAL MAIN 3 IC3005(3/6)

NU B10 NU A11 NU D10

R3321 4.7K

R3285 47 R3286 47 R3284 47

R3701 OPEN R3702 OPEN

R3710 100 C3707 1

TO DIGITAL TO DIGITAL MAIN 6 MAIN 1 IC3005(6/6) IC3005(1/6)

R3326 4.7K

R3343 OPEN

R3334 10

C3194 0.1 C3195 0.1 C3196 0.1 C3198 C3199 C3200 C3201

CONTINUE DIGITAL 6 VGA-SDA VGA-SCL

CONTINUE DIGITAL 4 P-ON+3.3V P-ON+5V

D3903 MM5Z5V6B

Q3302 RU1L002SNTL (BUFFER)

C3903 0.1 C3902 0.1

C3335 2.2

R3712 10K

R3703 OPEN

Q3701 2SC4081UBTLQ (BUFFER) R3709 220

C3285 0.1 C3286 0.1 C3336 1

C3706 1 R3708 110

COMPONENT -Y/VIDEO-IN COMPONENT -Pb-IN COMPONENT -Pr-IN JK3701 DIGITAL AUDIO-OUT (COAXIAL)

C3709 100P R3704 100K R3705 100K

AUDIO(L)-IN

AUDIO(R)-IN CONTINUE DIGITAL 5 SCL SDA AUDIO(L)-IN AUDIO(R)-IN CONTINUE DIGITAL 5 SPDIF

J 10-13

L PL13.8BSCD2

Digital Main 3 Schematic Diagram [TYPE B] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section.

C3009 OPEN

R3064 100 R3065 100

4 IC3002 K4T51163QJ-BCE7 (DDR2 SDRAM) C3029 C3030 C3031 C3032 C3033 C3034 C3035 C3037 C3038 C3039 C3040 C3041 C3140

0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1

*A VDD VREF J2 C3010 0.1

1-O3 2-O3 3-O3 SD-DQ15 SD-DQ12 SD-DQ10 SD-DQ9 SD-DQ14 SD-DQ13 SD-DQ11 SD-DQ8

3 4-O3 5-O3 6-O3

SD-DQ3 SD-DQ2 SD-DQ7 SD-DQ6 SD-DQ4 SD-DQ1 SD-DQ5 SD-DQ0

E2 A2 R8 R7 R3

NU NU NU NU NU

B7 A8 B3 B9 B1 D9 D1 D3 D7 C2 C8 F7 E8 F3 F9 F1 H9 H1 H3 H7 G2 G8

UDQS UDQS/NU UDM DQ15 DQ12 DQ10 DQ9 DQ14 DQ13 DQ11 DQ8 LDQS LDQS/NU LDM DQ3 DQ2 DQ7 DQ6 DQ4 DQ1 DQ5 DQ0

CKE CK CK CS RAS CAS WE BA2/NU BA1 BA0 A12 A11 A10/AP A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 ODT

K2 J8 K8 L8 K7 L7 K3 L1 L3 L2 R2 P7 M2 P3 P8 P2 N7 N3 N8 N2 M7 M3 M8 K9

R3083 100

R3049 150

IC3006 F25L32QA-1009AG2S (MEMORY) 1 CS

VCC 8

2 SO

NU 7

3 WP

SCK 6

4 GND

SI 5

CN3009 1 2 3 4

C3246 1

L3025 EXC24CG900U

33x4

R3031

33x4

R3032

33x4

VSS *B

R3033

R3034

C3073 0.1

R3479 10K

(USB JACK) BUS-POWER USBDN USBDP GND

C3051 0.1

SD-DQ15 SD-DQ14 SD-DQ13 SD-DQ12 SD-DQ11 SD-DQ10 SD-DQ9 SD-DQ8 SD-DQ7 SD-DQ6 SD-DQ5 SD-DQ4 SD-DQ3 SD-DQ2 SD-DQ1 SD-DQ0

R3030

R3102 10K R3107 10K

C3050 0.1

3-M3 6-M3 2-M3 1-M3 5-M3 4-M3

*A:A1,A9,C1,C3,C7,C9,E1,E9, G1,G3,G7,G9,J1,J9,M9,R1 *B:A3,A7,B2,B8,D2,D8,E3,E7, F2,F8,H2,H8,J3,J7,N1,P9

*1 IC3005(3/6) R8A05011BG-U0 DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER

R3082 100

C3348 220/6.3V

33x4

R3016 R3084 R3087 R3070

33 10 10 150

R3089 R3092 R3093 R3094 R3095

47 47 47 47 22

R3099 5.6K

C3184 18P

M5 SD-VREF0 N3 GND XIN25 H15 XOUT25 H16 R8 N8 P7 R6 P6 N7 T5 P8 P4 T3 R4 T2 P3 T4 R3 N4 T6 R5 T7 R7 N5 P5

SD-DQ15 SD-DQ14 SD-DQ13 SD-DQ12 SD-DQ11 SD-DQ10 SD-DQ9 SD-DQ8 SD-DQ7 SD-DQ6 SD-DQ5 SD-DQ4 SD-DQ3 SD-DQ2 SD-DQ1 SD-DQ0 SD-UDM SD-LDM SD-UDQSN SD-UDQS SD-LDQSN SD-LDQS

H1 H3 J2 J1 J4 L1 K4 L2 L4 N2 P1 M3 M1 M2 L3 N1 J3 K3 K1 K2 H2 R2 R1 H4

SD-A4 SD-CAS SD-A11 SD-A0 SD-A10 SD-A1 SD-BA1 SD-A9 SD-WE SD-BA0 SD-BA2 SD-A3 SD-A5 SD-A12 SD-CKE SD-A7 SD-RAS SD-A6 SD-A2 SD-ODT SD-A8 SD-CLK SD-CLKN NU

P12 R11 P11 T11 T9 R9 R10 T10 P10

CS SOUT SIN SCK VBUS-EN VBUS-ST USBDP USBDN NU

ASEBRKAK-N ASEMD0 TRST-N TCK TDI TDO TMS TO DIGITAL MAIN 2 IC3005(2/6)

F15 F16 E16 E15 D16 D15 E14

R3223 1K

X3001 25MHz

C3183 20P

R3527 OPEN R3525 OPEN R3526 OPEN

R3522 10K R3395 4.7K

TXD0 G15 RXD0 G16

R3468 100 R3469 100 C3254 OPEN

BACKLIGHT-ADJ F3 VCOM-PWM F2 GND J14

CELL-PWR-CTRL D1 GPY10 E13 P-ON-H2 B16 HP-MUTE G13 BACKLIGHT-SW E2

C3255 OPEN

CN3010 1 2 3 C3253 4 OPEN

(NO CONNECTION) P-ON+5V UART0-TX UART0-RX GND

CONTINUE DIGITAL 5 CPU-RESET-N

R3511 22

CONTINUE DIGITAL 4 GPY10 CPU-RESET-N P-ON-H2 BACKLIGHT-ADJ BACKLIGHT-SW

100 22 22

R3503 10K TO DIGITAL MAIN 2 IC3005(2/6)

(NO CONNECTION) AL+3.3V GND ASEBRKAK-N ASEMD0 TRST-N TCK TDI TDO TMS CPU-RESET-N

CONTINUE DIGITAL 2 COMP-DET

R3516 100 R3517 100

R3211 R3233 R3188

R3396 4.7K

CN3012 1 2 3 4 5 6 7 8 9 10

CONTINUE DIGITAL 1 CELL-PWR-CTRL VCOM-PWM

R3510 22K

LED1 D14 REMOTE C14 AUDIO-MUTE C1

CONTINUE DIGITAL 5 LED1 REMOTE

R3515 4.7K R3213 22 R3217 22 R3234 OPEN

COMP-DET N12

NU H14

R3215

R3201 33K

CONTINUE DIGITAL 4 P-ON+1.8V P-ON+3.3V AL+3.3V P-ON+5V

CONTINUE DIGITAL 5 HP-MUTE AUDIO-MUTE BACKLIGHT-SW

C3072 10

IC3019 AP2151WG-7 (HIGH SIDE SW) 1 OUT IN 5 2 GND

C3327 1

3 /FLAG RN 4 R3480 10K

DIGITAL MAIN CBA UNIT

P 10-14

R PL13.8BSCD3

Digital Main 4 Schematic Diagram [TYPE B] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section.

*1 IC3005(4/6) R8A05011BG-U0 DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER

R3222 10K

L3027 BEAD R3106 47K

G L3030 0 C3181 0.1

Q3013 SSM3K309T (SW+12V)

C3127 1

C3124 1 C3128 1

C3125 1 C3129 1

C3126 1 C3130 1

C3132 10

C3133 10

C3134 1

R3228 OPEN

C3118 10

C3136 1

C3114 10

C3115 10

AVDD33 AVDD33 AVDD33 AVDD33

C3609 1

R3608 4.7K

C3139 0.1

H5 J5 M4 T1 M6 N6 M7 M8

3 CE

C3326 10

C3325 OPEN

C3324 OPEN

C3343 10

C3264 OPEN

C3322 10

C3321 OPEN

C3320 10

C3319 10

C3318 10

C3141 1

C3142 1

C3143 1

C3144 1

C3145 1

C3080 4.7

C3103 OPEN

C3148 1

C3149 10

C3150 1

C3007 0.1

R3133 10K C3090 1

C3088 R3137 4700P 2.7K

L3026 BEAD

C3151 1

C3152 1

C3154 1

VCCQ33 VCCQ33 VCCQ33 VCCQ33 VCCQ33 AVDD33

G4 F5 L12 K13 J12 N11

C3156 1

C3157 1

C3158 1

D3114 MM5Z5V6B

C3099 OPEN

R3142 OPEN

D3006 PTZTE255.1B

C3022 4.7

C3028 0.047 R3098 0 C3121 OPEN

C3043 R3005 4700P 4.3K

1 SS

BST 8

2 EN

IN 7

3 COMP

SW 6

R3149 3.9K R3145 1.2K

C3094 330/4V

C3086 10

3 GND

NU 6

4 NU

EN 5

R3110 10K R3109 3.3K

R3111 10K

L3003 OPEN IC3007 BD00IC0WEFJ (+1.8V REG.)

C3075 0.022 R3103 1.8K

C3079 220/6.3V

C3087 10

C3102 4.7

C3002 OPEN

C3003 0.1

C3091 OPEN R3141 OPEN

R3091 0

C3085 0.1

C3119 OPEN

C3017 R3001 2200P 8.2K

C3065 10

C3097 OPEN

C3001 0.1

1 SS

NU 7

3 GND

NU 6

4 NU

EN 5

C3069 10

CONTINUE DIGITAL 5 P-ON+3.3V CHECK+1.8V AL+3.3V P-ON+5V P-ON+3.3V(1) AMP+13V

IC3001 MP1472GJC452Z (+3.3V REG.) 1 SS

BST 8

2 EN

IN 7

3 COMP

SW 6

C3092 OPEN R3057 OPEN

2 EN

IN 7

3 COMP

SW 6

D3005 PTZTE255.1B

R3602 OPEN C3606 OPEN

R3004 33K R3003 6.2K

C3056 10

C3074 10

C3053 OPEN

C3014 0.1

GND 5

C3020 330/4V

C3021 10

C3059 R3014 10 270

R3601 OPEN C3605 OPEN

D3994 OPEN D3995 OPEN D3107 HSC119 R3140 18K

R3112 10K C3042 0.1

R3115 Q3103 OPEN 2SA1576UBTLQ (SWITCHING)

Q3102 2SC4081UBTLQ (SWITCHING)

R3113 10K

R3101 1K

C3238 R3139 OPEN 1K

Q3009 2SC4081UBTLQ (SWITCHING)

C3107 R3104 1 1K

R3114 47K

L3005 22uH

GND 5

CONTINUE DIGITAL 3 GPY10 CPU-RESET-N P-ON-H2 BACKLIGHT-ADJ BACKLIGHT-SW

L3002 33uH

D3112 MM5Z12B

R3108 47K

C3095 OPEN R3054 OPEN

C3068 OPEN

R3002 15K

C3105 OPEN

BST 8

CONTINUE DIGITAL 5 RESET PROTECT1 PROTECT3

VCC 8

2 FB

4 FB

GND 5 C3096 10

C3063 OPEN

C3994 OPEN

C3604 10

C3603 1

D3602 MM5Z5V6B

R3051 100

D3007 OPEN

R3603 OPEN C3607 OPEN

R3006 10K

C3995 OPEN

C3996 OPEN

DIGITAL MAIN CBA UNIT

V 10-15

CONTINUE DIGITAL 6 P-ON+3.3V AL+3.3V P-ON+3.3V(1) P-ON+5V CONTINUE DIGITAL 2 P-ON+3.3V P-ON+5V CONTINUE DIGITAL 1 P-ON+5V P-ON+21V P-ON+3.3V PROTECT3

R3008 1

1 VOUT D3106 HSC119

C3024 10

C3131 1

Q3004 2SC4081UBTLQ (SWITCHING)

R3143 15K

IC3003 MP1472GJC452Z (+5V REG.)

4 FB R3012 33K R3007 12K

R3043 180

NU 7

C3159 1

VSS *D *C:G5,G6,H6,J7,J11,J13,K6,K7, K11,L8,L9,M9,M11,N9,P9. *D:D2~D5,D12,E3~E5,E7,E9,F4,F6, F7,F10,F11,G7~G10,H7~H13,J6, J8~J10,K5,K8~K10,K12,L5~L7, L10,L11,P2,T8

C3019 0.022 R3062 1.8K

VCC 8

2 FB

L3009 10uH

AVDD33 E6 C3155 1

Q3003 2SC4081UBTLQ (SWITCHING)

R3060 2.7K R3059 2.7K

C3013 0.047

AVDD33 D6 L3006 BEAD

1 VOUT

C3610 1

IC3008 MP1472GJC452Z (+1.2V REG.)

4 FB

D3115 HSC119

NU 4 R3607 OPEN

C3083 0.015

D3113 MM5Z5V6B

R3079 10K R3606 OPEN

2 GND

C3611 R3609 OPEN OPEN

L3019 OPEN

E10 C2 C3 E11

IC3601 AP2121AK-3.3TRE1 (+3.3V REG.) 1 VIN VOUT 5

R3605 0

VDDCLK G11

VCCQ18 VCCQ18 VCCQ18 VCCQ18 VCCQ18 VCCQ18 VCCQ18 VCCQ18

D3104 HSC119 R3077 10K

L3021 BEAD

IC3004 BD00IA5WEFJ-E2 (+1.2V REG.)

R3086 4.7K

C3237 R3227 OPEN OPEN

C3135 0.1

R3036 100

D3103 HSC119 R3424 100

R3061 10K

Q3011 OPEN

AVDD12 M10

AVDD12 E8 AVDD12 F8 AVDD12 F9

C3265 R3138 10 OPEN R3423 R3097 47K 1.5K

Q3005 2SC4081UBTLQ (SWITCHING) D3101 HSC119 D3102 HSC119

VDD12 *C C3123 1

Q3101 2SC4081UBTLQ (SWITCHING)

R3105 10K

Q3006 2SA1576UBTLQ (SWITCHING)

D3105 OPEN

R3013 R3011 R3009 R3072 R3068

VDD12STB E12

R3100 22K

220 OPEN 100 100 100

C3160 0.1

OPEN OPEN OPEN OPEN OPEN OPEN

VCC33STB F12 VCC33STB G12

C3062 C3008 C3006 C3004 C3055 C3048

CONTINUE DIGITAL 3 P-ON+1.8V P-ON+3.3V AL+3.3V P-ON+5V

R3221 100

CN3701 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23

TO POWER SUPPLY CBA CN501 LED-CONT(NU) PROTECT1 PROTECT3 RESET BACKLIGHT-SW P-ON-H2 BACKLIGHT-ADJ AL+3.3V GND GND GND GND GND GND AMP+13V AMP+13V AMP+13V AMP+13V GND P-ON+21V P-ON+21V P-ON+21V P-ON+21V

X PL13.8BSCD4

Digital Main 5 Schematic Diagram [TYPE B] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section. CONTINUE DIGITAL 4 P-ON+3.3V CHECK+1.8V AL+3.3V P-ON+5V P-ON+3.3V(1) AMP+13V CONTINUE DIGITAL 3 LED1 REMOTE CN3101 1 2 3 4 5 6 7 8 9

C3559 OPEN

C3553 OPEN

R3183 OPEN

Q3010 OPEN

C3558 OPEN

C3556 OPEN

R3553 100

D3201 MM5Z5V6B

R3184 OPEN

D3501 MM5Z5V6B

R3186 OPEN R3314 R3315 R3316 C3231

R3995 10K

A15 B13 A13 C13 C12

22 OPEN 22 0.22

C3328 OPEN

C3217 C3218 C3223 C3224

R3862 10K

2.2 2.2 1 1

D3111 MM5Z5V6B

KEY-IN1 PROTECT3 LIGHT-SENS PROTECT1 LPF TO DIGITAL TO DIGITAL MAIN 6 MAIN 2 IC3005(2/6) IC3005(6/6)

A8 B8 B7 A7

CONTINUE DIGITAL 3 CPU-RESET-N

R3191 100

RESET J15

C3329 0.01

R3335 18K R3336 18K

CONTINUE DIGITAL 3 HP-MUTE AUDIO-MUTE BACKLIGHT-SW

R3219 22

HP-DET K16

R3185 OPEN

R3557 10

SCL SDA AUDIO(L)-IN AUDIO(R)-IN

R3401 0 R3220 33K

OPEN OPEN OPEN OPEN 1000P 1000P

R3556 10

R3555 OPEN

CONTINUE DIGITAL 6 HPD-SINK PWR

R3402 0

R3216 100

R3320 OPEN

C3555 OPEN R3551 100

R3210 100

HPD-SINK K14 PWR J16

Q3501 2SC4081UBTLQ (LED DRIVE)

CONTINUE DIGITAL 4 RESET PROTECT1 PROTECT3 CONTINUE DIGITAL 2

NU G1 NU E1 NU G2

D13 CHECK+1.8V

R3560 100K

C3554 C3560 OPEN 1 C3551 33P C3552 33P

R3312 10K

R3318 22K R3317 10K R3319 10K

TO FUNCTION CBA UNIT CN4052 SDA(NU) SCL(NU) GND KEY-IN1 REMOTE LED1 LIGHT P-ON+5V AL+3.3V

R3558 OPEN

R3552 100

Q3502 2SA1576UBTLQ (LED DRIVE) R3559 10K

C3229 R3502 C3227 R3501 C3233 C3232

*1 IC3005(5/6) R8A05011BG-U0 DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER

R3178 220

NU NU NU NU NU NU

AUDIO I/F

D11 D7 C6 C5 B6 A6 N10

R3340 C3219 C3220 C3216

10K 10 10 10

IC3009 PST8429UR (RESET) 1 GND OUT 4 2 VDD

D3108 OPEN

R3182 56K C3116 1000P

CD 3

C3106 1

C3113 0.033

CONTINUE DIGITAL 2 SPDIF

R3209 100 R3865 10K

R3561 10 R3809 OPEN

R3810 OPEN

R3864 1K

C3825 1

R3814 OPEN

R3870 220

Q3803 2SA1576UBTLQ (SWITCHING)

R3818 10K

R3813 OPEN

R3817 10K C3870 2200P

R3816 1.8K

R3819 100K C3808 1

C3992 1

R3815 47K

Q3802 2SC4081UBTLQ (SWITCHING)

POWER LIMIT

4 5

R3806 0

C3815 R3807 OPEN 1 C3816 1 C3817 1 Q3804 OPEN

PWM LOGIC

C3819 1 R3871 220

C3809 1 C3871 2200P

R3823 OPEN

9 GVDD

C3861 0.1

R3852 15K

BIAS VCC 6 7 8

C3852 1

C3854 220/6.3V C3855 1000P

R3854 OPEN C3828 1

C3859 0.1

L3801 10uH

C3802 0.22 C3803 0.22

2 1 MUTE

JK3703 HEADPHONE JACK

R3856 10K

C3857 47/25V

R3855 10K

C3858 100/16V

23 22

GND 19 POWER LIMIT

C3801 0.22

DRIVE

C3856 1000P IC3851 BH3547F (HEADPHONE AMP)

Q3862 OPEN

C3832 10

C3862 OPEN

C3853 220/6.3V 4 GND

25 GND 24

GAIN CONTROL

R3866 100K

R3853 OPEN

DRIVE

8 GND R3808 10K

C3851 1

Q3861 2SC4081UBTLQ (SWITCHING)

PVCCL 27

DRIVE

Q3801 2SC4081UBTLQ (SWITCHING)

R3851 15K

C3860 0.1

R3863 OPEN

PVCCL 28

7 AVCC R3812 10K

R3868 OPEN

R3869 OPEN

CONTROL LOGIC

R3811 0

R3805 10K

C3824 1000P

IC3801 TPA3110D2PWPR (AUDIO AMP)

R3822 10 1

C3993 0.1

R3861 10K

R3867 0

PWM LOGIC

C3827 1000P

C3833 OPEN

18 DRIVE 17

13 NU

PVCCR 16

14 PBTL

PVCCR 15

C3804 0.22

C3831 100/16V

C3826 100/16V

C3829 100/16V

R3801 OPEN C3807 OPEN L3802 10uH

C3811 1000P

C3820 D3801 1 OPEN

R3802 OPEN C3805 OPEN L3803 10uH

C3812 1000P

C3821 D3802 1 OPEN

R3803 OPEN C3806 OPEN L3804 10uH

C3813 1000P

C3822 D3803 1 OPEN

R3804 OPEN C3810 OPEN

C3814 1000P

C3823 D3804 OPEN 1

CN3801 1 2 3 4

SP(L)+ SP(L)SP(R)SP(R)+

SP3801 SPEAKER L-CH

SP3802 SPEAKER R-CH

DIGITAL MAIN CBA UNIT

BB 10-16

DD PL13.8BSCD5

Digital Main 6 Schematic Diagram [TYPE B] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section.

CONTINUE DIGITAL 4 P-ON+3.3V AL+3.3V P-ON+3.3V(1) P-ON+5V

C3316 10 D3993 OPEN

C3424 OPEN

C3427 OPEN

R3405 100 R3415 82K

R3486 3.9K

D3057 RB751S-40 R3237 27K

HDMI-CEC B15

B1 A1 B2 A2 B3 A3 B4 A4

HDMI I/F

C3987 OPEN

R3489 10K

VCC 61

VCC 55

28 GND

SCL-SINK C16

29 SCL-SINK

SDA-SINK C15

30 SDA-SINK

33 HDMI-SEL1 F1

C3204 OPEN

R3212 47K

R3509 22

R3236 560

R3010 1K

C3185 0.01

R3270 2.2K

C3187 2.2

R3991 10K

C3188 2200P

PWR M12 R3193 4.7K

HDMI-SCL G14 HDMI-SDA F14

D3003 RB751S-40

R3192 4.7K C3206 OPEN

CONTINUE DIGITAL 5 HPD-SINK PWR

C3207 OPEN

CONTINUE DIGITAL 2 VGA-SDA VGA-SCL R3451 10K

R3453 1.5K

1 VCC1

VCC2 16

2 SCL1

SCL2 15

3 SDA1

SDA2 14

4 WPB C3192 0.1

R3452 10K

R3281 100

Q3451 2SC4081UBTLQ (SWITCHING)

R3282 100

DIGITAL MAIN CBA UNIT

5 VCC-OUT

D3001 RB751S-40

D3002 RB751S-40 R3022 10K

SDA3 11 SCL3 10

8 VCC0

VCC3 9

R3276 47K C3018 R3040 2.7K 0.1

R3029 1K

JK3004 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19

R3025 1K

Q3002 2SC4081UBTLQ (SWITCHING) R3027 10K

R3073 0 R3074 0 R3075 0 R3076 0 R3081 0

NU 13

7 SCL0

R3273 47K

R3024 10K

GND 12

6 SDA0

C3208 OPEN

R3023 22K

IC3011 BU9883FV-WE2 (HDMI SERIAL EEPROM)

R3017 10K

R3992 0

C3186 4700P R3271 3K

JK3003 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19

Q3001 2SC4081UBTLQ (SWITCHING)

R3018 1K

R3990 OPEN

EXT-RES C4 PLL-XFC-A B5 PLL-XFC-P A5

R3214 47K

C3005 R3019 2.7K 0.1 47

R3497 4.7K

C3205 OPEN

VCC

R3496 4.7K

HOT-PLUG- 50 DETECT2 NU 49

GND

R3994 OPEN

31 HOT-PLUGDETECT-SINK 32 HDMISEL0

VCC

HDMI-SEL0 G3

R3514 100 R3508 22

HOT-PLUGDETECT1

HPD-SINK F13

R3487 4.7K

HDMISEL1 NU

R3488 4.7K

R3058 10K

JK3002 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19

Q3008 2SC4081UBTLQ (SWITCHING)

R3063 1K

HDMI SW

25 VCC

C3990 1P

R3055 1K

GND 58

24 C3984 OPEN

R3278 47K

22 GND 23

C3985 OPEN

R3275 47K

19 VCC

C3986 OPEN

C3203 OPEN

C3023 R3066 2.7K 0.1

18 C3988 OPEN

C3202 OPEN

IC3018 TMDS351PAGR (HDMI SW)

HOT-PLUG- 64 DETECT3 63

17 C3989 OPEN

GND

AUDIO DECODER

C3422 OPEN

VCC

VIDEO DECODER

C3420 OPEN

GND

TO DIGITAL MAIN 5 IC3005(5/6)

C3426 1

VCC

TO DIGITAL MAIN 2 IC3005(2/6)

Q3014 2SK3018 RU1L002SNTL (BUFFER)

C3425 1

*1 IC3005(6/6) R8A05011BG-U0 DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER

C3423 1

GND

C3421 1

R3078 OPEN R3080 OPEN

C3191 0.1

HH 10-17

JJ PL13.8BSCD6

Power Supply CBA Top View [TYPE A] CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F602) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail.

2.5A 250V

CAUTION ! : For continued protection against risk of fire, replace only with same type 2.5A, 250V fuse. ATTENTION : Utiliser un fusible de rechange de mĂŞme type de 2.5A, 250V.

C1006

GP002 J136

R67

J142 FG

J134

P-ON+21V

GND

CN501

J170

R67

ALL+3.3V J180

Q657

Q658

J185

PROTECT1

R679

D650

J137 P-ON+21V

C662

C603

C602

C654

AMP+13V

GND

J179

J177

AMP+13V J178

J162 GND

D602

BC604

JS604

C614

+B JS606

RISK OF FIREREPLACE FUSE AS MARKED 04

L601

WHITE NEUTRAL

JS602

R601

CN601

BLACK LIVE

D601

T 2.5A L/250V F602

SA601

C605

No.2

D604 BC603

TOOL NO. A B C D E F G H I J

GND

D662

AMP+13v

J186

GND

BC601 DRAIN

DRAIN

D603

J164

DRAIN

J156

C617 JS605

R602

JS603

BC602

D654

L602

HOT

J165

DRAIN

C663

BA3AF0F0102 3

06 C6 J182 GATE

J166

D608

D607

J183 SOURCE

J141

SA602

COLD

P-ON+21V J187

J181 AMP+13V

J184 FG

R611

C1018

C656

IC601 IC602

GND

J163

J195

GT601

D651

C655

BL-SW

J169

P-ON+21V

J171

GND J152

J190 J153 CS

J174 GND

PROTECT3

L1001

C653

D655

J176 ADIM-P

OVP

J140

C65

GND

J194

J173

J175 CS

J172 P-ON+21V

C1007

R1015

J154 PROTECT3

P-ON+21V J135

J139

P-ON+21V

C652 D653

D660

J196

D652

J143 P-ON+21V

P-ON+21V

C1001 C651

GND

J147 GND

J188 GND C1002

J150

RESET AMP+13V

J144 J146

J189 ILED

P-ON-H2

OVP

J191 GND

J151 ALL+3.3V

GP001

NOTE: The voltage for parts in hot circuit is measured using hot GND as a common terminal.

CN1001 2

J138 LED-CONT

J145

Because a hot chassis ground is present in the power supply circuit, an isolation transformer must be used when repairing. Also, in order to have the ability to increase the input slowly, when troubleshooting this type of power supply circuit, a variable isolation transformer is required.

JS601 GP003

10-18

BA3AF0F01023

Power Supply CBA Bottom View [TYPE A] CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F602) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail.

CAUTION ! : For continued protection against risk of fire, replace only with same type 2.5A, 250V fuse. ATTENTION : Utiliser un fusible de rechange de mĂŞme type de 2.5A, 250V.

2.5A 250V

2 CN1001 Q1003

C1001

J145 J144 GND J146

C651

C652

J147 R668 GND

D653

R669 R677

C65

D663 R653

R691

J169

J171

R1014 C635

R1007

R1011

D1002

D650

R693

C607

Q602

SA602

J186

C609

C624

GND

J141

P-ON+21V J187

FG J184 R606

C608

C622 C621 R616 R617

D607A

R619 R611

D608

R603

R615

D608A R604

R614

R623

D607

+B JS603

Q621 R608

R618

J166

J165

C614

R612

R622 J183

JS604

Q601

J164

GATE J182

R602 D603

J156

JS605

DRAIN

BC604

C617

DRAIN

L602

SOURCE

BC601

GND J162

R609 D605 D609A

C623 D623 R621

JS606

GND

FG J142

C610

R613

D621

BA3AF0F0102 3

GT601

J195

R607

D654A

D602

IC601 IC602

C602

D610

D406 J181 AMP+13V

R655 J163

R654

J134 AMP+13V

R657

R659

D655A C603

R672

AMP+13v

GND

J179

J177

C665 R682 R680 R681

AMP+13V J178

GND

IC651

D662

C663

GND

D656

C654

C656

R651

R663

C660

R660

D658

D405 R670

D654

R665

D657

R690

R673 R671

R662

D664

D650A

J185

R67

C661

C638 C639

PROTECT1

R687 Q656

R658 C666

R675

R683

R67

R679

J170

CN501

R684

R686

Q658A

C662 C664

Q658

R688

R689

J137 P-ON+21V

Q657A

Q657

J180 ALL+3.3V

P-ON+21V

BL-SW

PROTECT3

C631

C633

Q1001

R1019

D1005 R685

R674

C655

C1018

D651

R1031

R661

Q650 R667 R666

R652

R1020

R1001

D661

R692

D653A

D1004

D660

D651A

R664 C630

GP001

J143 Q653 P-ON+21V

D652

J196

J135

P-ON+21V

R1016

RESET AMP+13V

D652A

D655

J140

R1017

P-ON+21V

J139

C653

D1001

D1007

R1013

P-ON+21V

C1017

J190 J153 CS

IC1001

R1005 GND J152

J172 P-ON+21V

J194

GND

R1006

C632

R1003

C1011 L1001

C1019

P-ON+21V

C1014 J174 GND

P-ON-H2

J150

GND J188 C1002

R1027

R1015

OVP

ADIM-P J176 C1015 R1012 R1004

Q659

ALL+3.3V J151

C1003

J154

J136 J175 CS J173 C1013 C1020 OVP C1016 R1030 C1012

GND

C1007

R1028 R1029

GP002

C1006

C1009 C1010

R1022 R1021

R1023 R1024 R1018

D1006

J138

LED-CONT

C1005 C1004

R1009 R1010 R1025 R1026

NOTE: The voltage for parts in hot circuit is measured using hot GND as a common terminal.

GND J191

J189 ILED

D604 BC603

C605

D601

JS602

SA601

L601

T 2.5A L/250V F602 CN601

R601

JS601

BC602

GP003

10-19

BA3AF0F01023

Power Supply CBA Top View [TYPE B] CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F602) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail.

2.5A 250V

CAUTION ! : For continued protection against risk of fire, replace only with same type 2.5A, 250V fuse. ATTENTION : Utiliser un fusible de rechange de mĂŞme type de 2.5A, 250V.

C1006

J176 ADIM-P

OVP

D603

J162 GND

JS605

D602

+B C614

JS603 +B JS606

RISK OF FIREREPLACE FUSE AS MARKED 04

L601

WHITE NEUTRAL

JS602

R601

CN601

BLACK LIVE

SA601

T 2.5A L/250V F602

D601

C605

No.1

D604 BC603

GND

J179 GND

GND J177

AMP+13V J178

D662

C617

R602 JS604

PROTECT3 J171

P-ON+21V CN501

J170

R 6 R67 AMP+13v

J186

P-ON+21V J187

GND

C6 BC604

DRAIN

J156 DRAIN DRAIN J164

DRAIN

D654

L602

HOT

J165

J166

C663

BA3AFCF0102 3

BC601

06 C6 J182 GATE D607

J183 SOURCE

J141

SA602

COLD

D608

R679

678

C603

J142 FG

J181 AMP+13V

BC602

ALL+3.3V J180

Q658

PROTECT1

C662

J134 AMP+13V

J184 FG

R611

C1018

J185

C654

Q657

J137 P-ON+21V

D650

C656

GND

IC601 IC602

GND

J195

J163

C602

GT601

D651

C655

BL-SW J169

GND J152

P-ON+21V

J194

J174 GND

J190 J153 CS

L1001

C653 J140

GND

J172 P-ON+21V

C1007

GP002 J136 J175 CS J173

OVP

R1015

J154 PROTECT3

P-ON+21V J135

D655 J139

C652

J196

D653

D660

P-ON+21V

C1001 C651

D652

J143 P-ON+21V

J188 GND C1002

J150

J145 RESET J144 AMP+13V

J147 GND

J189 ILED

P-ON+21V

J191 GND

J151 ALL+3.3V P-ON-H2

J146 GND

NOTE: The voltage for parts in hot circuit is measured using hot GND as a common terminal.

CN1001 2

J138 LED-CONT

GP001

JS601 GP003

10-20

BA3AFCF01023

Power Supply CBA Bottom View [TYPE B] CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F602) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail.

2.5A 250V

CAUTION ! : For continued protection against risk of fire, replace only with same type 2.5A, 250V fuse. ATTENTION : Utiliser un fusible de rechange de mĂŞme type de 2.5A, 250V.

2 CN1001 Q1003

C1001

D652

D651A D653

D663 R653

R691

D650

D651

D650A R665

R693

FG J184

J186

C607

SA602

R606 Q602 C609

GND

J141

C624 C608

D603 +B

JS604

+B JS603 R603

R622 R615

R623 C622 C621 R616 R617

D608A

D607A

R619 R611

R614

R608

R618

R604

D604

Q621

D608

J165

C614

R612

D607

R602

GATE J182

BC604

C617

Q601 J166

DRAIN J156 DRAIN J164

L602

SOURCE J183

BC601

GND J162

R609 D605 D609A

C623 D623 R621

JS606

GT601

D621 D654A

D602

GND

FG J142

R607 R613

D406

BA3AFCF0102 3 JS605

IC601 IC602

C610

D610

R655 J163

R654

C602

J134 AMP+13V J181 AMP+13V

P-ON+21V J187

AMP+13v

D662

R672

R659

J195

D405

C660 R657

R660

D655A C603

R67

J177

J179 GND

AMP+13V J178

IC651

GND

C665 R682 R680 R681

GND

J185

Q658A

D656

R67

R679

J170

CN501

C663

C656

Q658

C654

R658 C666

D658

R651

R663

R661 R674

Q650 R667 R666 R675

D657

R673 R690 R671 R670

D654

J137 P-ON+21V

Q1001

R662

D664

D661

R692

C655

C1018

PROTECT1

Q657A

Q657

J180 ALL+3.3V

P-ON+21V

BL-SW

R686

R669 R677

D660

J196

J135

J139 D655

J169

J171 PROTECT3

R683

R687 Q656

J147 R668 GND

R652

R688

R689

GP001

J143 Q653 P-ON+21V

D652A

D653A D1002 R1019

D1005 R685

GND J146

C651

C652

P-ON+21V

RESET J145 AMP+13V J144

R1020

R1001 R1031

C661

C638 C639

C653 J140

R1016

P-ON+21V

C1017 D1007

R1007

R1011

C633

R684

R1017

D1004

R1014

C631

D1001

P-ON-H2

J150

R664

C635

C662 C664

GND J188 C1002

R1006 R1013

C630

J190 J153 CS

IC1001

R1005 GND J152

J172 P-ON+21V

J194

GND

C632

R1003

L1001

C1019

J154

C1014 J174 GND

C1011

Q659

ALL+3.3V J151

C1003

R1015

OVP

ADIM-P J176 R1027 C1015 R1012 R1004

J136 J175 CS J173 C1013 C1020 OVP C1016 R1030 C1012

GND

C1007

R1028 R1029

GP002

R1023 R1024 R1018

D1006 C1006

C1009 C1010

R1022 R1021

C1005 C1004

R1009 R1010 R1025 R1026

NOTE: The voltage for parts in hot circuit is measured using hot GND as a common terminal.

LED-CONT J138 GND J191

J189 ILED

BC603

C605 D601 JS602

SA601

L601

T 2.5A L/250V F602 CN601

R601

JS601

BC602

GP003

10-21

BA3AFCF01023

SIDE

REAR

11-1

HEADPHONE JACK

USB JACK

PC-RGB-IN

HDMICONNECTOR-3

HDMICONNECTOR-2

HDMICONNECTOR-1

DIGITAL AUDIO-OUT (COAXIAL)

AUDIO(R)-IN

AUDIO(L)-IN

COMPONENT -Pr-IN

COMPONENT -Pb-IN

COMPONENT -Y/VIDEO-IN

TUNER UNIT CN3801

SP3802 SPEAKER R-CH

DIGITAL MAIN CBA UNIT

CL3801

SP3801 SPEAKER L-CH

[TYPE B] CN3006

[TYPE A] CN3013

CN3701

CN3101

CL3006

CL3701

CL3101

CN501

CN4052

CN1001 2

LCD PANEL ASSEMBLY

POWER SUPPLY CBA

FUNCTION CBA UNIT

B CN601

AC CORD

WIRING DIAGRAM

PL13.8WI

EXPLODED VIEWS

A16

LCD1

CL3006 L4

del 8 mo

L350

32PF [All A5

W01

A17

A13

B12 A9 A6

[32PFL3508/F7(Serial No.:ME1)]

B23 CL3701 GP002

L23

B23

GP001

Digital Main CBA Unit

[32PFL1508/F8(Serial No.:DS1)] Function CBA Unit

L23

CL3801

GP003

B18

CL3101

Power Supply CBA L23

B17

B18 B17

AC601 SP3801

L24

W02 L4

CL3006

L24

SP3802

[32PFL3508/F8(Serial No.:XA2), 32PFL1508/F8(Serial No.:XA1)]

SA1 L24 X6 L24

See Electrical Parts List for parts with this mark.

A15 SSK1

12-1

PL13.8_A CEX

Packing

[32PFL3508/F7 (Serial No.:ME1)] X7

SSK1 X2 X3

X4 Tape

Tape SA1

Tape

S3 S6

[All models except for 32PFL3508/F7 (Serial No.:ME1)] S12

Packing Tape

FRO

FR ON

Some Ref. Numbers are not in sequence.

Packing Tape

12-2

PL13.8PEX

TYPE A PARTS LIST [32PFL3508/F8 (Serial No.: XA1)] Mechanical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.

LCD PANEL ASSEMBLY

NOTE: Parts that are not assigned part numbers (---------) are not available.

CONTROL PLATE A3UFZZT

2EMH00096

SENSOR LENS A3UFZZT

2EMM00095

B12

SHIELD PLATE A3UFZZT

2EMS00072

CL3006

FFC WIRE ASSEMBLY 30PIN(W/SHIELD) 30P/ WX1A3AF0P401 FFC/SHIELD/500MM

SCREW P-TIGHT M3X8 BIND HEAD+ BLK

GBHP3080

LCD MODULE

----------

Ref. No.

Description

Ref. No.

REAR COVER A3AF0UT

1EM030166

BOTTOM COVER A3AF0UT

1EM030167A

A13

JACK HOLDER A31M0UT

1EM334000

A15#

RATING LABEL A3AFEMA

----------

A16

LOGO LABEL A3AFEMA

----------

AC601#

AC CORD UL/CSA/1680/NO/BLACK

WAC162LTE002

B17

WALL MOUNT BRACKET A11N0UH

1EM434637

B18

WALL MOUNT COVER A2170UT

1EM332137

B23

WIRE LABEL A3AF0UT

----------

CL3101

FFC WIRE ASSEMBLY 9PIN 9PIN/WHITE/ 184MM

WX1A3AF0S102

CL3701

FFC WIRE ASSEMBLY 23PIN 23PIN/WHITE/ 130MM

WX1A3AF0S121

CL3801

WIRE ASSEMBLY 4PIN 4PIN/320MM&30MM

WX1A3AF0C311

SCREW P-TIGHT M3X8 BIND HEAD+ BLK

GBHP3080

L23

SCREW S-TIGHT M3X6 BIND HEAD+

GBJS3060

L24

S-TIGHT SCREW M3X6 BIND HEAD+BLACK

GBHS3060

SA1

STAND ASSEMBLY A20F0PT

1ESA32345

SP3801

SPEAKER MAGNETIC 8立/8W S0310F14

DS08110XQ002

SP3802

SPEAKER MAGNETIC 8立/8W S0310F14

DS08110XQ002

SSK1

STAND SCREW KIT A31M0UT(SCREW PTIGHT M4X14 BIND HEAD+BLK)

1ESA34004

CARTON A3AFEMA

STYROFOAM TOP A3AF0UT

1EM030285

STYROFOAM BOTTOM A3AF0UT

1EM030286

Part No.

LCD PANEL ASSEMBLY

U3FF2PA

FRONT CABINET A3AFEMA

2EMM00125

DECORATION PLATE A3UFZZT

2EMH00095

Consists of the following

Part No.

Description

LCD1#

W01

WIRE ASSEMBLY 2PIN 2PIN/70MM/1PIN-RED WX1U3FF2-W01

PACKING 2EMC00096

SET BAG A31F0UT

2EMC00088

SERIAL NO. LABEL A01PBUH

----------

S12

CARTON LABEL A3AFEMA

----------

ACCESSORIES X1

POLYETHYLENE BAG HDPE 180X340XT0.03

1EM435579

X2#

OWNERS MANUAL A3AFEMA

2EMN00031A

REMOTE CONTROL UNIT YKF335-001

URMT39JHG001

BATTERY R03-B500/01S

XB0M451CZB01

QUICK START GUIDE A3AFEMA

2EMN00032A

2013/06/12

13-1

A3AFECA.fm

Ref. No.

NOTES: 1. Parts that are not assigned part numbers (---------) are not available. 2. Tolerance of Capacitors and Resistors are noted with the following symbols. C.....±0.25%

D.....±0.5%

F.....±1%

G.....±2%

J......±5%

K.....±10%

M.....±20%

N.....±30%

Z.....+80/-20%

DIGITAL MAIN CBA UNIT Ref. No.

Description

Part No.

Description

Part No.

C605

CAP ELE 330µF/200V/M/87

CEB3310S6016

C606

CERAMIC CAP. 820pF/2kV

CA3D821PAN04

C607

CHIP CERAMIC CAP. B K 1800pF/50V

CHD1JK30B182

C608

CHIP CERAMIC CAP.(1608) B K 0.022µF/50V

CHD1JK30B223

C609

CHIP CERAMIC CAP. B K 0.068µF/50V

CHD1JK30B683

C610

CHIP CERAMIC CAP.(1608) CH J 100pF/50V

CHD1JJ3CH101

C614#

CAP METALLIZED FILM 0.22µF/275V/K

CTA224PKR001

C616#

SAFTY CAP. 1000pF/250V KX

CA2E102MR101

C617#

CAP CERAMIC 100pF/250V KX

CA2E101MR100

C622

CHIP CERAMIC CAP.(2125) B K 10µF/6.3V

CHE0KK30B106

C623

CHIP CERAMIC CAP.(1608) B K 4.7µF/6.3V

CHD0KK30B475

C651

CAP ELE 470µF/25V/M/85

CED4710V8006

C652

CAP ELE 470µF/25V/M/85

CED4710V8006

C653

CAP ELE 470µF/25V/M/85

CED4710V8006

C654

CAP ELE 470µF/16V/M/85

CEC4710V8006

C655

CAP ELE 470µF/16V/M/85

CEC4710V8006

C656

CAP ELE 1µF/50V/M/85

CEF1R00V8006

C660

CHIP CERAMIC CAP.(1608) B K 0.22µF/25V

CHD1EK30B224

C663

CAP ELE 100µF/10V/M/85

CEB1010V8006

C665

CHIP CERAMIC CAP.(1608) B K 0.1µF/50V

CHD1JK30B104

C666

CHIP CERAMIC CAP.(1608) B K 0.22µF/25V

CHD1EK30B224

C1001

CAP ELE 470µF/25V/M/85

CED4710V8006

DIGITAL MAIN CBA UNIT

A3AFEMMA-001

C1002

CAP ELE 470µF/25V/M/85

CED4710V8006

IC3001

IC DC-DC CONVERTER MP1472GJC452Z

NSCA0T09M021

C1003

CHIP CERAMIC CAP.(1608) B K 1µF/25V

CHD1EK30B105

IC3002

IC 512MB DDR2 SDRAM K4T51163QJ-BCE7

NSCA0R0SM048

C1004

CHIP CERAMIC CAP.(1608) B K 1µF/25V

CHD1EK30B105

IC3003

IC DC-DC CONVERTER MP1472GJC452Z

NSCA0T09M021

C1006

CAP ELE 47µF/100V/M/85

CEH4700V8006

IC3004

IC REGULATOR BD00IA5WEFJ-E2

QSCA0T0RM233

C1007

CAP ELE 47µF/100V/M/85

CEH4700V8006

IC3005

IC DTV-C7V R8A05011BG-U0/256FHP

QSAA0R0HT057

C1009

CHIP CERAMIC CAP.(3216) X7R K 1.0µF/100V

CA2A105MR080

IC3006

IC 32M-BIT SERIAL FLASH MEMORY W25Q32FVSSIG

NSCA0R0ZM018

C1010

CHIP CERAMIC CAP.(3216) X7R K 1.0µF/100V

CA2A105MR080

C1011

CHIP CERAMIC CAP.(3216) X7R K 1.0µF/100V

CA2A105MR080

C1012

CHIP CERAMIC CAP.(1608) B K 1µF/25V

CHD1EK30B105

IC3007

IC LDO REGULATOR BD00IC0WEFJ/HTSOP-J8 QSCA0T0RM397

IC3008

IC DC-DC CONVERTER MP1472GJC452Z

NSCA0T09M021

IC3009

IC RESET IC-PST8429UR

QSCA0T0MM075

IC3011

IC EEPROM BU9883FV-WE2

QSCA0T0RM105

IC3013

IC SINGLE BUS BUFFER 74LVC1G126GW

NSCA0TNXP004

IC3014

IC SINGLE BUS BUFFER 74LVC1G126GW

NSCA0TNXP004

C1013

CHIP CERAMIC CAP.(1608) B K 1000pF/50V

CHD1JK30B102

C1015

CHIP CERAMIC CAP.(1608) B K 0.047µF/25V

CHD1EK30B473

C1016

CHIP CERAMIC CAP. B K 2200pF/50V

CHD1JK30B222

C1017

CHIP CERAMIC CAP.(1608) B K 0.022µF/50V

CHD1JK30B223

C1018

CERAMIC CAP. B K 100pF/1kV

CCD3AKN0B101

C1019

CHIP CERAMIC CAP.(1608) B K 1µF/25V

CHD1EK30B105

C1020

CHIP CERAMIC CAP. B K 2200pF/50V

CHD1JK30B222

IC3018

IC HDMI SW TMDS351PAGR /PAG-64

NSCA0T0TY068

IC3019

IC USB HIGH-SIDE SW AP2151WG-7/SOT25/ 5PI

NSCA0TDES015

IC3601

IC REGULATOR AP2121AK-3.3TRE1

NSCA0TBCD026

IC3621

IC DC-DC CONVERTER MP1472GJC452Z

NSCA0T09M021

CN501

FFC CONNECTOR IMSA-9615S-23A-PP-A

JC96J23ER007

IC3801

IC D-CLASS AUDIO POWER AMPLIFI TPA3110D2PWPR

NSCA0T0TY073

CN601#

CONNECTOR S2P3-VH (LF)(SN)

JCVHC02JG002

CN1001

IC HEADPHONE AMP BH3547F SOP 8PIN

QSZBA0TRM119

PH CONNECTOR TOP 2P B2B-PH-K-S (LF)(SN)

J3PHC02JG029

IC3851 TU3901

TUNER UNIT U9001UT

U9001UT D601

DIODE 1N5406BH

NDL1001N5406

D602

DIODE 1N5406BH

NDL1001N5406

D603

DIODE 1N5406BH

NDL1001N5406

D604

DIODE 1N5406BH

NDL1001N5406

D605

ZENER DIODE MM5Z4V3B

ND1BMM5Z4V3B

D607A#

ZENER DIODE SMD TFZVTR27B

QD1B00TFZV27

D608#

DIODE ZENER 1ZB36BB

NDWZ0001ZB36

D609A#

DIODE SCHOTTKY SMD RB520SM-30 T2R

QD1ZRB520SM3

D610

DIODE SWITCHING HSC119 TRF -E

QD1Z00HSC119

D621

DIODE SWITCHING HSC119 TRF -E

QD1Z00HSC119

D623

ZENER DIODE MM5Z30B

ND1B0MM5Z30B

D650

DIODE SCHOTTKY SB3150BH

NDWZ00SB3150

CONNECTORS

DIODES

FUNCTION CBA UNIT Ref. No.

Description FUNCTION CBA UNIT

Part No. A3AFEMSW-001

POWER SUPPLY CBA Ref. No.

Description POWER SUPPLY CBA Consists fo the following

Part No. A3AF0MPW-001

CAPACITORS C602#

SAFTY CAP. 1000pF/250V KX

CA2E102MR101

D651

DIODE SCHOTTKY SB3150BH

NDWZ00SB3150

C603#

SAFTY CAP. 1000pF/250V KX

CA2E102MR101

D653

DIODE SCHOTTKY SB3A0BH

NDWZ000SB3A0

C604#

CAP METALLIZED FILM 0.22µF/275V/K

CTA224PKR001

D654#

DIODE ZENER 1ZB20BB

NDWZ0001ZB20

D655

DIODE SCHOTTKY SB3A0BH

NDWZ000SB3A0

2013/06/12

13-2

A3AFEEL.fm

Ref. No.

Description

Part No.

Ref. No.

Description

Part No.

RES CHIP 1608 1/10W 0 Ω

RRXA000HH014

R675

RES CHIP 1608 1/10W F 68.0k Ω

RTW6802HH008

R677

RES CHIP 1608 1/10W J 10k Ω

RRXA103HH013

QD1Z00HSC119

R680

RES CHIP 1608 1/10W J 100 Ω

RRXA101HH013

IC SHUNT REGULATOR SL431A-AT

NSZBA0TAUK01

R681

RES CHIP 1608 1/10W F 10.0k Ω

RTW1002HH008

D664

ZENER DIODE SMD TFZVTR4.7B

QD1B0TFZV4R7

R682

RES CHIP 1608 1/10W 0 Ω

RRXA000HH014

D1001

DIODE SCHOTTKY SMD SK210TD

ND1Z0SK210TD

R690#

RES CHIP 1608 1/10W J 1.5 Ω

RRXA1R5HH013

D1004

DIODE SWITCHING HSC119 TRF -E

QD1Z00HSC119

R1001

RES CHIP 1608 1/10W J 470 Ω

RRXA471HH013

D1005

DIODE SWITCHING HSC119 TRF -E

QD1Z00HSC119

R1003

RES CHIP 1608 1/10W J 1.0k Ω

RRXA102HH013

D1006

ZENER DIODE SMD TFZVTR30B

QD1B00TFZV30

R1004

RES CHIP 1608 1/10W J 10k Ω

RRXA103HH013

D1007

ZENER DIODE MM5Z11B

ND1B0MM5Z11B

R1005

RES CHIP 1608 1/10W J 100k Ω

RRXA104HH013

R1006

RES CHIP 1608 1/10W J 10k Ω

RRXA103HH013

D656

DIODE FAST RECOVERY RS1BJTD

ND1Z0RS1BJTD

R674

D657

ZENER DIODE MM5Z11B

ND1B0MM5Z11B

D660

IC SHUNT REGULATOR SL431A-AT

NSZBA0TAUK01

D661

DIODE SWITCHING HSC119 TRF -E

D662

ICS IC602#

IC PHOTOCOUPLER TLP781F(D4-FUNBLL F)

QPEL781FBLLF

R1007

RES CHIP 1608 1/10W J 100k Ω

RRXA104HH013

IC1001

IC LED BACKLIGHT CONTROLLER BD9488FGE2/SOP/18P

QSCA0T0RM418

R1009

RES CHIP 3216 1/4W F 1.00 Ω

RT1R00RYL007

R1010

RES CHIP 3216 1/4W F 1.00 Ω

RT1R00RYL007

R1011

RES CHIP 1608 1/10W F 33.0k Ω

RTW3302HH008

COILS L601#

COIL LINE FILTER JLB20154/18MH

LLEG0Z0XB022

R1012

RES CHIP 1608 1/10W F 56.0k Ω

RTW5602HH008

L602#

COIL LINE FILTER JLB20154/18MH

LLEG0Z0XB022

R1013

RES CHIP 1608 1/10W F 240k Ω

RTW2403HH008

L1001

COIL POWER INDUCTORS DIP RP1315BNP101M/100µH

LLF1010SF013

R1014

RES CHIP 1608 1/10W F 3.00k Ω

RTW3001HH008

R1015

METAL OXIDE RES. 1W J 0.18 Ω

RN01R18ZU001

R1019

RES CHIP 1608 1/10W J 200 Ω

RRXA201HH013

R1020

RES CHIP 1608 1/10W F 240k Ω

RTW2403HH008

R1021

RES CHIP 1608 1/10W 0 Ω

RRXA000HH014

R1022

RES CHIP 1608 1/10W F 10.0k Ω

RTW1002HH008

R1023

RES CHIP 3216 1/4W J 3.9k Ω

RRX4392HH034

R1024

RES CHIP 3216 1/4W J 1.5k Ω

RRX4152HH034

R1025

RES CHIP 1608 1/10W J 1.0k Ω

RRXA102HH013

R1026

RES CHIP 1608 1/10W J 51 Ω

RRXA510HH013

R1027

RES CHIP 1608 1/10W F 22.0k Ω

RTW2202HH008

R1028

RES CHIP 1608 1/10W F 9.10k Ω

RTW9101HH008

R1029

RES CHIP 1608 1/10W F 9.10k Ω

RTW9101HH008

R1030

RES CHIP 1608 1/10W J 1.0k Ω

RRXA102HH013

R1031

RES CHIP 1608 1/10W J 10 Ω

RRXA100HH013

TRANSISTORS Q601#

FET MOS TK7P60W.RVQ(S

QF2Z0TK7P60W

Q602#

NPN TRANSISTOR SMD 2SC5344SY

NQZY2SC5344S

Q621

CHIP TRANSISTOR KTC3875S-Y-RTK/P

NQ1YKTC3875S

Q650

CHIP TRANSISTOR KTC3875S-Y-RTK/P

NQ1YKTC3875S

Q653

CHIP TRANSISTOR KTC3875S-Y-RTK/P

NQ1YKTC3875S

Q656

CHIP TRANSISTOR KTC3875S-Y-RTK/P

NQ1YKTC3875S

Q658

TRANSISTOR 2SA950-O (TE2 F T)

QQS002SA950F

Q1001

FET MOS SMD AP18T10AGH-HF

NF2Z18T10AGH

Q1003

FET MOS SMD AP18T10AGH-HF

NF2Z18T10AGH

RESISTORS R601#

RES. CARBON FILM J 1/2W J 1.2M Ω

RCX2125T1003

R603

RES CHIP 3216 1/4W J 470k Ω

RRX4474HH034

R604

RES CHIP 3216 1/4W J 470k Ω

RRX4474HH034

R606

RES CHIP 3216 1/4W J 330 Ω

RRX4331HH034

R607

RES CHIP 3216 1/4W J 330 Ω

RRX4331HH034

R608

RES CHIP 3216 1/4W J 1.5k Ω

RRX4152HH034

R609

RES CHIP 1608 1/10W J 100 Ω

RRXA101HH013

R611#

METAL OXIDE RES. 2W J 0.36 Ω

RN02R36ZU001

R612

RES CHIP 3216 1/4W J 5.6k Ω

RRX4562HH034

R613

RES CHIP 3216 1/4W J 180 Ω

RRX4181HH034

R614

RES CHIP 3216 1/4W J 470k Ω

RRX4474HH034

R621

RES CHIP 1608 1/10W J 560 Ω

RRXA561HH013

R622

RES CHIP 1608 1/10W 0 Ω

RRXA000HH014

R623

RES CHIP 1608 1/10W J 10k Ω

RRXA103HH013

R651#

RES CHIP 1608 1/10W J 1.0 Ω

RRXA1R0HH013

R652

RES CHIP 1608 1/10W F 56.0k Ω

RTW5602HH008

R653

RES CHIP 1608 1/10W F 33.0k Ω

RTW3302HH008

R654

RES CHIP 3216 1/4W J 180 Ω

RRX4181HH034

R655

RES CHIP 3216 1/4W J 180 Ω

RRX4181HH034

R657

RES CHIP 3216 1/4W J 3.9k Ω

RRX4392HH034

R658

RES CHIP 1608 1/10W J 2.7k Ω

RRXA272HH013

R659

RES CHIP 1608 1/10W F 27.0k Ω

RTW2702HH008

R660

RES CHIP 1608 1/10W F 3.90k Ω

RTW3901HH008

R661

RES CHIP 1608 1/10W F 3.30k Ω

RTW3301HH008

R662

RES CHIP 1608 1/10W F 3.30k Ω

RTW3301HH008

R666

RES CHIP 1608 1/10W 0 Ω

RRXA000HH014

R667

RES CHIP 1608 1/10W J 8.2k Ω

RRXA822HH013

R668

RES CHIP 1608 1/10W J 47k Ω

RRXA473HH013

R669

RES CHIP 1608 1/10W J 10k Ω

RRXA103HH013

R670

RES CHIP 1608 1/10W J 270 Ω

RRXA271HH013

R671

RES CHIP 1608 1/10W J 270 Ω

RRXA271HH013

R672

RES CHIP 1608 1/10W J 270 Ω

RRXA271HH013

2013/06/12

MISCELLANEOUS

13-3

BC601

BEADS INDUCTOR FBR07HA121SB-00

LLBF00STU030

BC602

BEADS INDUCTOR FBR07HA121SB-00

LLBF00STU030

BC603

BEADS INDUCTOR FBR07HA121SB-00

LLBF00STU030

BC604

BEADS INDUCTOR FBR07HA121SB-00

LLBF00STU030

F602#

FUSE TIME RAG SLT250V2.5A

PDGSLB0NG252

GP001

EARTH PLATE A31FBUT

1EM440258

GP002

EARTH PLATE A31FBUT

1EM440258

GP003

EARTH PLATE A31FBUT

1EM440258

JS603

WIRE CP STP-S-0.50

XZ40F0REN001

JS604

WIRE CP STP-S-0.50

XZ40F0REN001

SA601#

VARISTOR 10D 471K SVR

NVQZVR10D471

T601#

TRANS POWER SRW26LEC-T11H016

LTT2PC0TE005

A3AFEEL.fm

TYPE A PARTS LIST [32PFL3508/F8 (Serial No.: XA2)] Mechanical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTE: Parts that are not assigned part numbers (---------) are not available.

Different parts from the original model 32PFL3508/F8 (Serial No. : XA1) Ref. No.

Description

Part No.

LCD1#

LCD PANEL ASSEMBLY

CL3006

FFC WIRE ASSEMBLY 30PIN(W/SHIELD) 30P/ WX1A3AFBP401 FFC/SHIELD/415MM

L23

SCREW S-TIGHT M3X6 BIND HEAD+

GBJS3060

W02

WIRE ASSEMBLY 50PIN FFC SF2500080XWY00

WX1U3DF0-F01

2013/06/28

U3DF0PA

13-4

A3AFLCA.fm

Electrical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTES: 1. Parts that are not assigned part numbers (---------) are not available. 2. Tolerance of Capacitors and Resistors are noted with the following symbols. C.....±0.25%

D.....±0.5%

F.....±1%

G.....±2%

J......±5%

K.....±10%

M.....±20%

N.....±30%

Z.....+80/-20%

Different parts from the original model 32PFL3508/F8 (Serial No. : XA1) Ref. No.

R1015

Description

Part No.

DIGITAL MAIN CBA UNIT

A3AFLMMA-001

POWER SUPPLY CBA

A3AFBMPW-001

METALOXIDE RES 2W J 0.12Ω

RNJR12PAK002

2013/06/28

13-5

A3AFLEL.fm

TYPE A PARTS LIST [32PFL3508/F7 (Serial No.: ME1)] Mechanical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTE: Parts that are not assigned part numbers (---------) are not available.

Different parts from the original model 32PFL3508/F8 (Serial No. : XA1) Ref. No. A15#

Description RATING LABEL A3AF2UT

Part No. ----------

A16

LOGO LABEL A3AF2UT

----------

A17

ENERGY GUIDE LABEL A3AF2UT

----------

CARTON A3AF2UT

2EMC00230

S12

Not used

X2#

OWNERS MANUAL A31M2UT

2EMN00083A

QUICK START GUIDE A3AF2UT

2EMN00111

REGISTRATION CARD (PHILIPS) A2176UT

1EMN29339

2013/09/12

13-6

A3AF2CA.fm

D.....±0.5%

F.....±1%

G.....±2%

J......±5%

K.....±10%

M.....±20%

N.....±30%

Z.....+80/-20%

Different parts from the original model 32PFL3508/F8 (Serial No. : XA1) Ref. No.

Description DIGITAL MAIN CBA UNIT

2013/09/12

Part No. A3AF2MMA-002

13-7

A3AF2EL.fm

TYPE A PARTS LIST [32PFL1508/F8 (Serial No.: XA1)] Mechanical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTE: Parts that are not assigned part numbers (---------) are not available.

Different parts from the original model 32PFL3508/F8 (Serial No. : XA1) Ref. No.

Description

Part No.

A15#

RATING LABEL A3AFRMA

----------

A16

LOGO LABEL A3AQZUH

----------

CARTON A3AFRMA

2EMC00204

S12

CARTON LABEL A3AFRMA

----------

LCD1#

LCD PANEL ASSEMBLY

U3DF0PB

FRONT CABINET A3AFRMA

2EMM00211

Not used

CONTROL PLATE A31F0UT

SENSOR LENS A3AF0UT

1EM334258

B12

SHIELD PLATE A3AF0UT

1EM334260

CL3006

FFC WIRE ASSEMBLY 30PIN(W/SHIELD) 30P/ WX1A3AFBP401 FFC/SHIELD/415MM

L23

SCREW S-TIGHT M3X6 BIND HEAD+

GBJS3060

W02

WIRE ASSEMBLY 50PIN FFC SF2500080XWY00

WX1U3DF0-F01

2013/08/19

1EM334317

13-8

A3AFRCA.fm

D.....±0.5%

F.....±1%

G.....±2%

J......±5%

K.....±10%

M.....±20%

N.....±30%

Z.....+80/-20%

Different parts from the original model 32PFL3508/F8 (Serial No. : XA1) Ref. No.

R1015

Description

Part No.

DIGITAL MAIN CBA UNIT

A3AFRMMA-001

POWER SUPPLY CBA

A3AFBMPW-001

METALOXIDE RES 2W J 0.12Ω

RNJR12PAK002

2013/08/19

13-9

A3AFREL.fm

TYPE B PARTS LIST [32PFL1508/F8 (Serial No.: DS1)] Mechanical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTE: Parts that are not assigned part numbers (---------) are not available.

Different parts from the original model 32PFL3508/F8 (Serial No. : XA1) Ref. No. A4

Description BOTTOM COVER A3AFCUH

Part No. 1EM031005

A15#

RATING LABEL A3AFVMH

----------

A16

LOGO LABEL A3AQZUH

----------

SA1

STAND ASSEMBLY A21F0UH

1EM029048A

SSK1

STAND SCREW KIT A3AFCUH(SCREW PTIGHT M4X14 BIND HEAD+BLK)

1ESA35205

CARTON A3AFVMH

2EMC00248

SET BAG A21F0UH

1EM335137

S12

CARTON LABEL A3AFVMH

----------

X2#

OWNERS MANUAL A3ATAMA

2EMN00033A

QUICK START GUIDE A3ATAMA

2EMN00034A

LCD1#

LCD PANEL ASSEMBLY

U34F7P0

FRONT CABINET A3AFVMH

2EMM00224

Not used

CONTROL PLATE A31F0UT

SENSOR LENS A3AF0UT

1EM334258

B12

SHIELD PLATE A3AF0UT

1EM334260

CL3006

FFC WIRE ASSEMBLY 30PIN(W/SHIELD) 30P/ WX1A3AFCP411 FFC/SHIELD/600MM

2013/08/19

1EM334317

13-10

A3AFVCA.fm

D.....±0.5%

F.....±1%

G.....±2%

J......±5%

K.....±10%

M.....±20%

N.....±30%

Z.....+80/-20%

Different parts from the original model 32PFL3508/F8 (Serial No. : XA1) Ref. No. IC3006

Description

Part No.

DIGITAL MAIN CBA UNIT

A3AFVMMA-001

32MBIT C-MOS SERIAL FLASH F25L32QA100PAG2S

NSCA0R0E1019

IC3621

Not used

TU3901

TUNER UNIT U9001UH

U9001UH

FUNCTION CBA UNIT

A3AFVMSW-001

POWER SUPPLY CBA

A3AFNMPW-001

R1014

RES CHIP 1608 1/10W F 5.60k Ω

RTW5601HH008

R1015

RES METAL OXIDE 1W J 0.12 Ω

RNJR120HH013

2013/08/19

13-11

A3AFVEL.fm

REVISION HISTORY

Chassis PL13.8 • 2013/6/18

32PFL3508/F8 (Serial No.: XA1) Added

• 2013/7/9

32PFL3508/F8 (Serial No.: XA2) Added

• 2013/8/22

32PFL1508/F8 (Serial No.: XA1) Added

• 2013/8/22

32PFL1508/F8 (Serial No.: DS1) Added

• 2013/9/26

32PFL3508/F7 (Serial No.: ME1) 1st draft added

14-1

PL13.8REV

COMPARISON LIST OF MODEL NAMES

Chassis PL13.8 32PFL3508/F7

(ME1)

A3AF2UT

TYPE A

32PFL3508/F8

(XA1)

A3AFEMA

TYPE A

(XA2)

A3AFLMA

TYPE A

(XA1)

A3AFRMA

TYPE A

(DS1)

A3AFVMH

TYPE B

32PFL1508/F8

PL13.8COM