Bondall BondCrete Application Guide

Page 1

APPLICATION GUIDE THE PROVEN PERFORMER THAT NEVER LETS GO REV 1207

www.bondall.com


CONTENTS Concrete Floors Rendering Smooth Surfaces Rendering Rough Surfaces Plaster Setting Rendering Painted Surface Rendering Masonry Blocks Rendering Steel Form Concrete Tiling Concrete Floors Tiling Wall or Floor Sheeting Tiling Clay Brick or Masonry Walls Tile Grouting Bonding Quarry or Ceramic Tiles Clear Proofing Interior Face Sealer to Key Porous Surface Adhesive for Craftwork Dust Proofing Cement Paint Premium Limewash Bedding Mortars Resurfacing Wooden Sills and Steps Non slip Interior Surface

pg. pg. pg. pg. pg. pg. pg. pg. pg. pg. pg. pg. pg. pg. pg. pg. pg. pg. pg. pg. pg.

3 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25

References Test Results

pg. pg.

26 29

www.bondall.com


APPLICATION GUIDE

BONDCRETE pg. 3

BONDCRETE for concrete floor topping over 6mm 1

MATERIALS REQUIRED

SEALING Apply a sealing coat of diluted BONDCRETE (BONDCRETE 1: WATER 4) and allow to dry

BondCrete Water

MIX

H20

Clean Sand or Fine Aggregate

x1 )+(

- (

H20

x4 )

S 2

Cement

C

BONDCOAT Apply a bondcoat of diluted BONDCRETE (BONDCRETE 4: WATER 1), progressively as the toppings are being laid and avoid walking on the bondcoat.

SEALING

MIX

3

H20

x1 )

H20

x1 )

TOPPING MIX

APPLICATION

x4 )+(

- (

x1 )+(

- (

Apply topping while bondcoat is still "tacky�. Suggested mix is (CLEAN SAND OR FINE AGGREGATE 2-3: CEMENT 1) mixed to a workable consistency with BONDCRETE admixture (BONDCRETE 1: WATER 10) in place of normal water.

3 2 1

MIX

- (

+ ADMIX

- (

S

x2 )+( x1 )+(

C

H20

x1 ) x10 )

Notes: Where expansion jointing materials are used in the original floor, provision must be made for these joints to be followed through the new toppings. This should also apply to later areas of tiles.

www.bondall.com


APPLICATION GUIDE

BONDCRETE pg. 4

BONDCRETE for patching or laying up to 6mm topping on concrete floors and driveways. 1

MATERIALS REQUIRED

SEALING Apply a sealing coat of diluted BONDCRETE (BONDCRETE 1: WATER 4) and allow to dry.

BondCrete Water

MIX

H20

Clean Sand

x1 )+(

- (

H20

x4 )

S 2

Cement

C

BONDCOAT Apply a bondcoat of diluted BONDCRETE (BONDCRETE 1: WATER 1) and allow to dry.

APPLICATION

MIX

x1 )+(

- (

H20

x1 )

3 2

3

1

TOPPING While the bondcoat is wet or tacky carry out patching or topping. Mix (CLEAN SAND 2OR3: CEMENT 1) mixed to a workable consistency with BONDCRETE admixture (BONDCRETE 1: WATER 10) in place of normal water. Avoid over troweling, do not over wet the mix.

MIX

- (

+ ADMIX

www.bondall.com

- (

S

x2 )+( x1 )+(

H20

C

x1 ) x10 )


APPLICATION GUIDE

BONDCRETE pg. 5

BONDCRETE for patching concrete floors and driveways. 1

MATERIALS REQUIRED

PREPARATION Damaged areas to be patched should be keyed out to a minimum depth of 6mm.

BondCrete Water

H20

Clean Sand

S

Cement

C PREPARATION

2

COATING Apply coat of diluted BONDCRETE (BONDCRETE 1: WATER 4) and allow to dry.

MIX

x1 )+(

- (

3

H20

x4 )

BONDCOAT Apply a bondcoat of diluted BONDCRETE (BONDCRETE 4: WATER 1) and while wet apply the Patching Mortar.

1

MIX

4 APPLICATION

H20

x1 )

PATCHING Using a Patching Mortar made up of (CEMENT 1: SAND 3) mixed to a workable consistency with BONDCRETE admixture (BONDCRETE 1: WATER 10) in place of normal water.

4 2

x4 )+(

- (

3

MIX

- (

+ ADMIX

www.bondall.com

- (

C

x1 )+( x1 )+(

S

H20

x3 ) x10 )


APPLICATION GUIDE

BONDCRETE pg. 6

BONDCRETE for rendering onto smooth surfaces eg: beams and lintels where no key exists. 1

MATERIALS REQUIRED

SEALING Apply 1 sealing coat of diluted BONDCRETE (BONDCRETE 4: WATER 1).

BondCrete Water

MIX

H20

Clean Sand

S

Cement

C

Fine Metal Screenings

2

x1 )

H20

SPLASH COATING While the previous coat is still “tacky” apply one coat of (CEMENT 1: SAND 1/4, FINE METAL SCREENINGS 2) mixed to a “Splash Coat” consistency with diluted BONDCRETE (BONDCRETE 1: WATER 4).

MS

Render

x4 )+(

- (

RENDER

MIX

- (

SEALING

C

x1 )+( S x 1/4) +( MS x2 )

+ ADMIX

1

- (

3

x1 )+(

x4 )

H20

RENDERING Allow 24 hours before rendering using the specified cement render mixed with BONDCRETE admixture (BONDCRETE 1: WATER 10) in place of normal water.

APPLICATION

1

RENDER

2

+ ADMIX

3

1

- (

x1 )+(

H20

x10 )

Notes: Unless specified the suggested render mix is 2 /2 - 3 parts sand, 1 part cement mix to a workable consistency with diluted Bondcrete Admixture.

www.bondall.com


APPLICATION GUIDE

BONDCRETE pg. 7

BONDCRETE for setting a cement coat to a rendered surface which is rough and requires refinishing. 1

MATERIALS REQUIRED

SEALING Apply 1 sealing coat of diluted BONDCRETE (BONDCRETE 1: WATER 4) and allow to dry.

BondCrete Water

MIX

H20

Clean Sand

S

Cement

2

x1 )+(

- (

H20

x4 )

BONDCOAT a)To large holes and depressions apply a bondcoat of diluted BONDCRETE (BONDCRETE 1: WATER 1)

C

MIX

SEALING

x1 )+(

- (

H20

x1 )

b)Whilst bondcoat is still tacky, fill with a mixture of (SAND 5: CEMENT 2)

1

MIX

- (

S

x5 )+(

C

x2 )

c) Add enough diluted BONDCRETE (BONDCRETE 1: WATER 4) to make a mix workable consistency, fill any big holes and allow to dry.

APPLICATION

3

MIX

2

x1 )+(

- (

H20

x4 )

1 3

TREATING & REFINISHING a) Treat the surface with diluted BONDCRETE (BONDCRETE 1: WATER 4).

MIX

x1 )+(

- (

H20

x4 )

b) Whilst this coat is still tacky apply mixture of (CEMENT 2: SAND 1) with enough diluted BONDCRETE (BONDCRETE 1: WATER 4) to make a mix that can be toweled on 4mm thick.

MIX

- (

+ ADMIX

www.bondall.com

- (

C

x2 )+(

S

x1 )

x1 )+(

H20

x4 )


APPLICATION GUIDE

BONDCRETE pg. 8

BONDCRETE for plaster setting onto concrete ceilings, walls, beams. 1

MATERIALS REQUIRED

SEALING Apply 1 sealing coat of diluted BONDCRETE (BONDCRETE 1: WATER 4) and allow to dry.

BondCrete Water

H20

Plaster

PLASTER

MIX

2

- (

x1 )+(

H20

x4 )

COATING & PLASTERING Add one coat of diluted BONDCRETE (BONDCRETE 1: WATER 1).

SEALING (a)

MIX

- (

x1 )+(

H20

x1 )

While this coat is still wet, plaster with Hard wall Plaster mixed to required consistency with diluted BONDCRETE (BONDCRETE 1: WATER 4) in place of normal water

1

(b) PLASTER APPLICATION

+

1 1

MIX

2 (a) 2 (b) 2

www.bondall.com

- (

x1 )+(

H20

x4 )


APPLICATION GUIDE

BONDCRETE pg. 9

BONDCRETE for rendering onto painted surface. 1

MATERIALS REQUIRED

To a sound painted surface which has been wire brushed apply one coat of diluted BONDCRETE (BONDCRETE 1: WATER 4) and allow to dry for 24 hours. Note: To ensure surface is sound do a tape test. Cut a cross cut into the painted surface and firmly press a quality masking take over the cross cut area, and pull off. If little or no paint is removed proceed. Do this over several areas to ensure integrity of painted surface.

BondCrete Water

H20

Clean Sand

S

Cement

C

Fine Aggregate

AG

Render

COATING

MIX

x1 )+(

- (

x4 )

H20

RENDER

2

BONDCOAT Apply a bondcoat of diluted BONDCRETE (BONDCRETE 4: WATER 1).

PREPARATION

1

MIX

x4 )+(

- (

H20

x1 )

While this coat is still “tacky” apply one coat (CEMENT 4: SAND 1: FINE AGGREGATE 2) mixed to a “Splash Coat” consistency with diluted BONDCRETE (BONDCRETE 1: WATER 4).

APPLICATION

MIX

1

- (

+

2

MIX

3

- (

C

x4 )+( S x1 ) +( AG x2 ) x1 )+(

H20 2

x4 )

RENDERING

3

Allow to dry for 24 hours before rendering using a specified cement Render with BONDCRETE admixture (BONDCRETE 1: WATER 10) in place of normal water. RENDER

+ ADMIX

- (

x1 )+(

H20

x10 )


APPLICATION GUIDE

BONDCRETE pg. 10

BONDCRETE for rendering onto masonry blocks. 1

MATERIALS REQUIRED

BONDCOAT

(a) Apply bondcoat of diluted BONDCRETE (BONDCRETE 1:WATER 1).

BondCrete Water

MIX

H20

RENDER

Render

- (

x1 )+(

H20

x1 )

(b) While this coat is still tacky apply the Render

using a Render mixed with BONDCRETE admixture (BONDCRETE 1: WATER 10) in place of normal water.

APPLICATION

RENDER

+

1 (a)

ADMIX

APPLICATION

1 (a)

1 (b)

www.bondall.com

- (

x1 )+(

H20

x10 )


APPLICATION GUIDE

BONDCRETE pg. 11

BONDCRETE for rendering onto steel form structural concrete. 1

MATERIALS REQUIRED

PREPARATION It is important to remove all Form Release Agents which have transferred from the Forms to the concrete.

BondCrete Water

H20

2

RENDER

Render

Applying a sealing coat of diluted BONDCRETE (BONDCRETE 4: WATER 1).

PREPARATION

1

SEALING

MIX

- (

3

x4 )+(

H20

x1 )

RENDERING While this coat is still wet or tacky apply the Render in the normal manner. For improved adhesion use a Render mixed with BONDCRETE admixture (BONDCRETE 1: WATER 10) in place of normal water.

APPLICATION

RENDER

+

2

ADMIX

3

www.bondall.com

- (

x1 )+(

H20

x10 )


APPLICATION GUIDE

BONDCRETE pg. 12

BONDCRETE for tiling concrete floors old or new. 1

MATERIALS REQUIRED

If either the Concrete or the back of the Tiles is porous, seal the porous surface with a sealing coat of diluted BONDCRETE (BONDCRETE 1: WATER 4) and allow to dry.

BondCrete Water

H20

Clean Sand

S

Cement

C

SEALING

- (

MIX

2

x1 )+(

H20

x4 )

BONDCOAT Apply a bondcoat of diluted BONDCRETE (BONDCRETE 1: WATER 1) and lay the Bedding while this coat is still sticky.

PREPARATION

1

- (

MIX

x1 )+(

H20

x1 )

TILES

APPLICATION

3 2 1

Beddings up to 6mm

Bedding over 6mm

(CEMENT 1: FINE SAND 2)

(CEMENT 1: FINE SAND 3)

MIX

MIX

( C x1 ) +( S x2 )

( C x1 ) +( S x3 )

mixed to workable consistency with diluter BONDCRETE (BONDCRETE 1: WATER 4) in place of normal water.

ADMIX

3

- (

x1 )+(

H20

x4 )

SCREEDING & TILING Screed Bedding to required level and bed the Tiles immediately.

Notes: Beddings must be fresh. Any Bedding Mix not used within 45 minutes of mixing should be discarded. Any Bedding Mix or grout containing BONDCRETE must be cleaned off the face of the tile before it dries. Floor tiles must be applied on full beddings only.

www.bondall.com


APPLICATION GUIDE

BONDCRETE pg. 13

BONDCRETE for tiling to wall or floor sheeting, old or new compressed F.C Hardiflex, Versilux hard board, Chipboard or plaster board. 1

MATERIALS REQUIRED

PREPARATION Determine that the Sheeting used is suitable (i.e. Showers and Bathrooms should be sheeted in materials for wet areas).

BondCrete Water

H20

Clean Sand

S

Cement

C SEALING

2

SEALING Seal the sheet with a sealing coat of Diluted BONDCRETE (BONDCRETE 1: WATER 4) and allow to dry.

MIX

3

x1 )+(

- (

H20

x4 )

BONDCOAT Apply a bondcoat of diluted BONDCRETE (BONDCRETE 1: WATER 1) to the dry sealed surface

MIX

x1 )+(

- (

H20

x1 )

Whilst tacky apply a Bedding Mix (CEMENT 1: FINE SAND 2) mixed to a workable consistency with diluted BONDCRETE (BONDCRETE 1: WATER 4) in place of normal water.

APPLICATION

4 3

MIX

2 1

- (

+ MIX

- (

4

C

x1 )+(

S

x2 )

x1 )+(

H20

x4 )

TILING If the Tiles have a porous back, coat the back with diluted BONDCRETE (BONDCRETE 1: WATER 4) and bed while both of the Tiles and the Bedding Mix are wet.

MIX

- (

x1 )+(

H20

x4 )

Notes: Beddings must be fresh. Any Bedding Mix not used within 45 minutes of mixing should be discarded. Any Bedding Mix or grout containing BONDCRETE must be cleaned off the face of the tile before it dries. Floor tiles must be applied on full beddings only.

www.bondall.com


APPLICATION GUIDE

BONDCRETE pg. 14

BONDCRETE for tiling clay brick or masonry block walls. 1

MATERIALS REQUIRED

PREPARATION Point up the Mortar Courses to bring them flush with the surface.

BondCrete

2 Water

If either the Concrete or the back of the Tiles or Porous, seal the porous surface with diluted BONDCRETE (BONDCRETE 1: WATER 4).

H20

Clean Sand

S

Cement

C PREPARATION

MIX

- (

3

x1 )+(

H20

x4 )

BONDCOAT Apply a bondcoat of diluted BONDCRETE (BONDCRETE 1: WATER 1) and lay the Bedding while this coat is still tacky.

2

1

SEALING

MIX

APPLICATION

2

- (

x1 )+(

H20

x1 )

Beddings up to 6mm

Bedding over 6mm

(CEMENT 1: FINE SAND 2)

(CEMENT 1: FINE SAND 3)

MIX

MIX

( C x1 ) +( S x2 )

( C x1 ) +( S x3 )

3 4

Mixed to workable consistency with diluted BONDCRETE (BONDCRETE 1: WATER 6) in place of normal water.

MIX

4

- (

x1 )+(

H20

x6 )

SCREEDING & TILING Screened Bedding to require level and bed the

Notes: Beddings must be fresh. Any Bedding Mix not used within 45 minutes of mixing should be discarded. Any Bedding Mix or grout containing BONDCRETE must be cleaned off the face of the tile before it dries. Floor tiles must be applied on full beddings only.

www.bondall.com


APPLICATION GUIDE

BONDCRETE pg. 15

BONDCRETE for tile grouting. 1

MATERIALS REQUIRED

PREPARATION Porous tiles should be thoroughly wet down before grouting to prevent the colouring materials entering the face of the tiles.

BondCrete Water

H20

Clean Sand

S

Cement

C

2

GROUTING Prepare a Grouting Mix (Cement 1: Sand 3) with BONDCRETE admixture (BONDCRETE 1: WATER 10). This mix can be coloured with iron oxides if required.

MIX

PREPARATION

- (

C

x1 )+(

S

x3 )

+

1

ADMIX

H20

APPLICATION

2

www.bondall.com

- (

x1 )+(

H20

x10 )


APPLICATION GUIDE

BONDCRETE pg. 16

BONDCRETE for bonding quarry or ceramic tiles to timber floors. 1

MATERIALS REQUIRED

PREPARATION Ensure boards are securely nailed.

BondCrete

2

Water

Sheet the floor with compressed F.C Sheeting. If a waterproof deck is required all sheet joints should be sealed with a flexible Caulking compound. Use sufficient nails to prevent any flexing in the sheet.

H20

Clean Sand

S

Cement

SHEETING

3

SEALING Apply a sealing coat of diluted BONDCRETE (BONDCRETE 1: WATER 4) to the sheeted floor and allow to dry.

C APPLICATION

MIX

1 - Preparation 5

4

H20

x4 )

BONDCOAT & BEDDING Apply a bondcoat of diluted BONDCRETE (BONDCRETE 1: WATER 1) to the surface.

4 2

x1 )+(

- (

3

MIX

x1 )+(

- (

H20

x1 )

While this coat is still “tacky” lay a Bedding Mix (CEMENT 1: CLEAN SAND 2) mixed to the workable consistency with diluted BONDCRETE (BONDCRETE 1: WATER 6) in place of normal water. Screen the Bedding Mix to the required level.

MIX Notes: Tile joints should be placed to correspond with the joints in the sheets so that any movement in the floor will be on the grout lines rather than cracking the tiles. Beddings must be fresh. Any Bedding Mix not used within 45 minutes of mixing should be discarded. Any Bedding Mix or grout containing BONDCRETE must be cleaned off the face of the tile before it dries.

- (

C

x1 )+(

S

x2 )

x1 )+(

H20

x6 )

+ MIX

- (

5

TILING If the tiles have porous back, coat the back with diluted BONDCRETE (BONDCRETE 1: WATER 1) and bed while both the Tiles and the Bedding Mix are still wet.

MIX

Floor tiles must be applied on full beddings only.

www.bondall.com

- (

x1 )+(

H20

x1 )


APPLICATION GUIDE

BONDCRETE pg. 17

BONDCRETE for clear proofing to interior face brickwork, stonework, decorative render etc. 1

MATERIALS REQUIRED

Surface should be cleaned by the appropriate method to remove any staining that will be visible through the transparent coating such as cement residue, efflorescence, timber stains, rust marks, mould, fungus, oil and grease.

BondCrete Water

H20

Clean Sand

S

Cement

PREPARATION

2

POINTING If desired point up holes in mortar lines using a mix (CEMENT 1: SAND 3) and enough BONDCRETE admixture (BONDCRETE 1: WATER 10) to make required consistency.

C PREPARATION

MIX

1

- (

C

x1 )+(

S

x3 )

+ ADMIX

- (

3

x1 )+(

H20

x10 )

SEALING While surface is damp but not wet, apply a sealing coat of diluted BONDCRETE (BONDCRETE 1: WATER 6). Allow to dry for at least 24 hours.

APPLICATION

2

MIX

3

- (

4

x1 )+(

H20

x6 )

SEALING Apply a second sealing coat of diluted BONDCRETE (BONDCRETE 1: WATER 4) to the DRY surface. If considered necessary a third coat may be applied the following day.

4

MIX

www.bondall.com

- (

x1 )+(

H20

x4 )


APPLICATION GUIDE

BONDCRETE pg. 18

BONDCRETE as a sealer and key to porous surfaces before applying water borne decorative paints. 1

MATERIALS REQUIRED

One sealing coat of diluted BONDCRETE (BONDCRETE 1: WATER 4) will provide an excellent Sealer or Key when applied to new or old Cement Rendered Walls, Plaster etc, before using water borne Decorative Paints (see paint manufacturers instructions). This Sealer is inexpensive and you will use less Paint. Allow 24 hours to dry. Do not attempt to apply oil based paints over BONDCRETE.

BondCrete Water

SEALING

H20

APPLICATION

1 MIX

www.bondall.com

- (

x1 )+(

H20

x4 )


APPLICATION GUIDE

BONDCRETE pg. 19

BONDCRETE as an adhesive for carpentry, joinery and general craftwork. MATERIALS REQUIRED

1

ADHESIVE Apply direct from container to one surface only. Press surfaces together and lightly clamp. BONDCRETE sets in approximately 30 minutes. Maximum strength is attained in 12 hours.

BondCrete

APPLICATION

1

www.bondall.com


APPLICATION GUIDE

BONDCRETE pg. 20

BONDCRETE for dust proofing and/or retarding oil penetration of interior concrete floors. 1

MATERIALS REQUIRED

To a thoroughly clean floor apply with a Broom, Brush or Roller, a sealing coat of diluted BONDCRETE (BONDCRETE 1: WATER 6). Leave to dry for approximately 12 hours.

BondCrete Water

SEALING

H20

MIX SEALING

- (

2

x1 )+(

H20

x6 )

SEALING Apply another sealing coat of diluted BONDCRETE (BONDCRETE 1: WATER 4) and allow to dry.

1

MIX APPLICATION

2

3

- (

x1 )+(

H20

x4 )

SEALING A third coat maybe added for better oil retardation. BONDCRETE will dry clear; binding surface particles together and produce a very pleasing smooth hard surface.

3

1

Notes: Do not seal floor with BONDCRETE if you intend to utilize an oil based paving paint or similar floor coating system.

www.bondall.com


APPLICATION GUIDE

BONDCRETE pg. 21

BONDCRETE cement paint. 1

MATERIALS REQUIRED

Oil, grease, mould and loose material should be removed prior to application. Mix only sufficient material that can be used in 40 minutes and allow to dry over night. Seal surface with diluted BONDCRETE (BONDCRETE 1: WATER 4).

BondCrete Water

H20

Cement

PREPARATION

C

MIX

- (

x1 )+(

H20

x4 )

PREPARATION CEMENT PAINTING

2 1

Mix diluted BONDCRETE (BONDCRETE 1: WATER 2) with 3 parts fresh Cement and apply by Roller to a lightly dampened surface to clean up old discoloured Concrete. Add oxide for coloured finishes.

MIX

APPLICATION

- (

x1 )+(

-

(

+ MIX

2

www.bondall.com

C

H20

x3 )

x2 )


APPLICATION GUIDE

BONDCRETE pg. 22

BONDCRETE as a premium limewash. 1

MATERIALS REQUIRED

SEALING Surfaces to be coated with limewash should be sealed with diluted BONDCRETE (BONDCRETE 1: WATER 4).

BondCrete Water

H20

MIX Lime

- (

x1 )+(

H20

x4 )

This should be allowed to dry properly before limewash is applied.

Mineral Turpentine

2

APPLICATION

LIMEWASH For approximately 20 litres of limewash: To 13L water in 20L plastic pail, add 4L Bondcrete and mix well. Slowly add 6kg lime, which has been sieved through a fine mesh and mix well to a smooth paste with a broad blade. Next add 200mL mineral turpentine and stir well to obtain a smooth consistency.

1

Next add 1L of water and stir thoroughly to give a smooth easily mixed light gel, which gives better brush penetration. Pastel colours can be obtained by the addition of oxide pigments at about 25 grams per litre of mix depending on shade required. The pigment should be well mixed to a smooth paste consistency in a small quantity of limewash prior to addition.

APPLICATION

1

2

Limewash should be allowed to stand preferably overnight and remixed prior to use. Some settlement is to be expected but this is easily remixed. Easier application of the second or subsequent coats and reduced cracking is achieved by damping down the surface with clean water. Coverage 8-10 square metres per litre, depending upon surface.

www.bondall.com


APPLICATION GUIDE

BONDCRETE pg. 23

BONDCRETE for bedding mortars for roofing tiles, ridge caps and other glazed masonry, terracotta and earthenware type surfaces. 1

MATERIALS REQUIRED

Using diluted BONDCRETE (BONDCRETE 1: WATER 6) prepare a Sand and Cement Mortar and use for Bedding, Pointing, Patching and Jointing. Colour with Oxides if required.

BondCrete Water

BEDDING

H20

Clean Sand

MIX

Cement

APPLICATION

1 1

www.bondall.com

- (

x1 )+(

H20

x6 )


APPLICATION GUIDE

BONDCRETE pg. 24

BONDCRETE to resurface old wooden sills and step treads affected by weathering etc. 1

MATERIALS REQUIRED

SEALING Apply a sealing coat of diluted BONDCRETE (BONDCRETE 1: WATER 4) and allow to dry.

BondCrete Water

MIX

H20

Clean Sand or Fine Aggregate

x1 )+(

- (

H20

x4 )

S 2

Cement

C

Sandpaper Sawdust

SS

BONDCOAT Apply a bondcoat of diluted BONDCRETE (BONDCRETE 4: WATER 1)

MIX APPLICATION

- (

x4 )+(

H20

x1 )

While this coat is still wet, prepare a mixture (SANDPAPER SAWDUST 3: CEMENT 1 ½ : SAND 1) mixed to rendering consistency with diluted BONDCRETE (BONDCRETE 1: WATER 4). Apply it with a Steel Trowl. Finish off with a Wooden Float and lightly trowel to a smooth finish. Allow to dry.

3 2 1

RENDER

- (

SS

+ MIX

3

- (

x3 )+( C x11/2 ) +( S x1 ) x1 )+(

H20 2

x4 )

BRUSHCOAT Apply a brushcoat of diluted BONDCRETE (BONDCRETE 1:WATER 4).

MIX

www.bondall.com

- (

x1 )+(

H20

x6 )


APPLICATION GUIDE

BONDCRETE pg. 25

BONDCRETE for a non slip interior surface. 1

MATERIALS REQUIRED

SEALING Brush on a sealing coat of diluted BONDCRETE (BONDCRETE1: WATER 4) and allow to dry.

BondCrete Water

MIX

H20

Sand, Carborundum chippings or similar

2

3

- Repeat

x1 )+(

H20

x4 )

BONDCOAT Apply a bondcoat of diluted BONDCRETE (BONDCRETE 4: WATER 1) and while this coat is still “tacky” distribute sand, Carborundum chippings or similar material over surface. Allow to dry.

APPLICATION

2

- (

4

MIX

1

- (

x4 )+(

H20

x1 )

Sweep away loose material.

3

REPEAT For greater thickness repeat step (2) allowing each coat to dry thoroughly before the next application.

4

BRUSHCOAT Finally apply brushcoat of diluted BONDCRETE (BONDCRETE 1: WATER 4). Add oxide for coloured finishes.

MIX

www.bondall.com

- (

x1 )+(

H20

x4 )


APPLICATION GUIDE

BONDCRETE pg. 26

Job References New Housing Authority Headquarters Building, Main Contractor: Hsin Chong Construction Co., Ltd. Quantity: 810 drums. China Overseas Building, Hennessy Road, Hong Kong Main Contractor: China Overseas Building Construction Ltd. Quantity: 70 drums. VTC HK Technical College, Tsing YI Island. Main Contractor: Shui On Contractors Ltd. Quantity: 1,195 drums Ko Chiu Road, Phase 1, Kowloon, Main Contractor: Chee Cheung Hing & Co., Ltd. Quantity: 383 drums HKUST Graduate Residences & Senior Staff Quarters, Sai Kung, N.T Main Contractor: Gammon Construction Ltd. Quantity: 460 drums Tung Chung Area 10, Phase 1 & 2, Lantau Island. Main contractor: Shui On Building Contractors Ltd. Quantity: 680 drums Tin Shui Wai Area 30, Phase 2, N.T. Main Contractor: Paul Y - ITC General Contractors Ltd. Quantity: 346 drums Tseung Kwan O Area 34/44, Phase 4, Kowloon, Main Contractor: Paul Y - ITC General Contractors Ltd. Quantity: 417 drums Tsz On Estate, Pahse 2, Kowloon, Main Contractor: Paul Y - ITC General Contractors Ltd. Quantity: 568 drums Marriot Hotel & One Pacific Place Office Building, Queensway, Hong Kong Main Contractor: Shui On Construction Co., Ltd. Quantity: 565 drums

www.bondall.com


APPLICATION GUIDE

BONDCRETE pg. 27

Job References No. 2 Queen's Road Central, Hong Kong, Main Contractor: Paul Y - ITC General Contractors Ltd. Quantity: 447 drums No. 9 May Road, Hong Kong, Main Contractor: Win House Industries Ltd. Quantity: 569 drums Kwai Chung Lot No. 452 & 455, Kowloon, Main Contractor: Win House Industries Ltd. Quantity: 1,240 drums Beacon Hill, Lung Ping Street, Kowloon, Contact A, B & C, Main Contractor: Tat Lee Construction Co., Ltd. Quantity: 1,005 drums Tin Shui Wai Area 31, Phase 2, N.T Main Contractor: Shui On Building Contractors Ltd. Quantity: 1,385 drums Ho Man Tin South, Phase 3, Kowloon, Main Contractor: Shui On Building Contractors Ltd. Quantity: 945 drums Tseung Kwan O Area 34/44, Phase 3, Kowloon, Main Contractor: Shui On Building Contractors Ltd. Quantity: 315 drums Mongkok West, Phase 1 & 2, Mongkok, Kowloon, Main Contractor: Hsin Chong Construction Co., Ltd. Quantity: 769 drums Citibank Plaza, Garden Road, Hong Kong, Main Contractor: Sung Foo Kee, Ltd. Quantity: 912 drums 'Park View' Tytam, Hong Kong, Main Contractor: Fudo Construction Co., Ltd./Hip Hing Construction Co., Ltd. Quantity: 600 drums Museum of Art, Tsimshatsui, Kowloon, Main Contractor: Paul Y Construction Co., Ltd. Quantity: 400 drums

www.bondall.com


APPLICATION GUIDE

BONDCRETE pg. 28

Job References Shatin Jocky Club, Grandstand II, Shatin, N.T Main Contractor: Shui On Construction Co., Ltd. Quantity: 720 drums Proposed Industrial Building, N.K.I.L 5851, Kowloon Bay, Kowloon, Main Contractor: Hsin Chong Construction Co., Ltd. Quantity: 600 drums Redhill Gardens, Tytam, Hong Kong, Main Contractor: Pilecon (HK) Ltd. Quantity: 750 drums New Tech Centre, Tsuen Wan, Kowloon, Main Contractor: Chevalier (Construction) Co,. Ltd. Quantity: 420 drums Hong Kong University of Science & Technology, Contract B2 Staff Housing, Phase 1, Sai Kung, Kowloon, Main Contractor: Sung Foo Kee, Ltd. Quantity: 380 drums Eaton Hotel, Nathan Road, Kowloon, Main Contractor: Sung Foo Kee, Ltd. Quantity: 285 drums Wah Ming Estate, Phase 1, Fanling, N.T. Main Contractor: Sung Foo Kee, Ltd. Quantity: 205 drums Tsuen Wan Central Public Libruary, Government Office Complex, Tsuen Wan, N.T. Main Contractor: Sung Foo Kee, Ltd. Quantity: 120 drums

www.bondall.com


APPLICATION GUIDE

BONDCRETE pg. 29

Test Results

www.bondall.com


APPLICATION GUIDE

BONDCRETE pg. 30

Test Results

www.bondall.com


APPLICATION GUIDE

BONDCRETE pg. 31

Test Results

www.bondall.com


113 Belmont Ave, Belmont 6104 Western Australia Phone: (08) 6272 3800 Fax: (08) 9277 4068 TOLL FREE: 1800 810 123

www.bondall.com


Turn static files into dynamic content formats.

Create a flipbook
Issuu converts static files into: digital portfolios, online yearbooks, online catalogs, digital photo albums and more. Sign up and create your flipbook.