PATTERN BOOK • VOLUME 1
shimmer
. COM
Class In A Box • 1,840 pcs Bead Mat & 3-in-1 Tool Included Makes 2 Necklaces, 2 Bracelets & 2 Sets of Earrings 34706012
only
25
$
13 FREE PATTERNS INSIDE
RECEIVE A FREE GIFT WITH YOUR PURCHASE Your coupon code is located on the back cover
800-366-2218 • WWW.PRIMABEAD.COM • FREE SHIPPING
Bethany necklace
Tools Needed: Needle Nose Pliers #4454 Crimping Pliers #4501 Wire Cutters #4457
Techniques to Know: Opening Jump Rings Crimp Tubes
2
Free Shipping . 10-25% Volume Discounts . Free Patterns
Materials: # 34713130
4mm Bronze Metallic Bicones (1pk)
$4.00 # 37450085
Purple/White Shell Bead Strand (3pks)
$4.00
# 34718104
Copper Small Chain (2pks)
$4.00 # 34719069
Copper Findings Pack (1pk)
$4.00 # 3202001
Gold 7-Strand Beading Wire (1pk)
$2.00
Instructions: 1. Cut the following lengths of beading wire: a 7”, a 9” and an 11” length.
2. Using crimp tubes, attach each wire to its own 4mm jump ring.
3. Thread the following pattern onto
the 7” wire: a bicone, a white oval, a bicone, a purple hexagon, a bicone, a white oval, a bicone, a purple hexagon, a bicone, a white oval and a bicone.
7. Cut (12) 8” lengths of chain. 8. Attach (2) chains to each 4mm jump ring. 9. Gather a set of chains from one end of each beaded section using a 6mm jump ring. Attach a toggle clasp to the jump ring.
10. Repeat the steps for the other set of chains and clasp.
4. Thread the following pattern onto
the 9” wire: a bicone, a white oval, a bicone, a purple hexagon, a bicone, a white oval, a bicone, a purple hexagon, a bicone, a white oval, a bicone, a purple hexagon, a bicone, a white oval and a bicone.
5. Thread the following pattern onto the 11” wire: a bicone, a white oval, a bicone, a purple hexagon, a bicone, a white oval, a bicone, a purple hexagon, a bicone, a white oval, a bicone, a purple hexagon, a bicone, a white oval, a bicone, a purple hexagon, a bicone, a white oval and a bicone.
6. Using crimp tubes, attach each wire to its own 4mm jump ring. Trim the excess wire.
Shop now at www.primabead.com/bethany
3
Blue Ice
coin knot earrings
Makes 16 pairs
Materials: # 34745025
# 34712124
$3.99
$1.99
# 34745020
# 34712100
$3.99
$2.00
Silver Satin Cord (1 pk)
Blue Metallic Cord (1 pk)
4
Silver Cord Ends (1 pk)
Silver Earring Wires (1 pk)
Free Shipping . 10-25% Volume Discounts . Free Patterns
Tools Needed: Needle Nose Pliers #4454 Wire Cutters #4457
Techniques to Know: Opening Jump Rings Cord Ends
Instructions: 1. Cut (2) 16� lengths of metallic blue cord and (1) 16� length of silver cord.
2. Weave the cords as a set, with silver cord
on the inside. Follow the pattern as shown on our website.
3. Shift the cords to make the knot tighter and more even.
4. Bring the ends together and trim the excess.
5. Use a metal cord end to secure the cords
together. Attach the earring wire to the hole of the cord end.
6. Repeat steps 1-5 for the matching earring.
Shop now at www.primabead.com/blueice
5
Gemstone cuff bracelet
Materials: # 34698109
# 3201801
$2.00
$2.69
# 34714124
# 22279001
$2.00
$3.40
Gold Cuff Bracelet (1 pc)
Green Agate Slice (1 pc)
Tools Needed: Round Nose Pliers #6858 Wire Cutters #4457
Techniques to Know: Wire Wrapping
Gold 24 Gauge Wire (1 pk)
E6000® Glue (1 tube)
Instructions: 1. Use E6000
to adhere the accent to the top center of the cuff. Allow the adhesive to dry thoroughly (according to manufacturers instructions) before adding the wire to prevent the agate from sliding on the cuff. ®
2. Cut a 36” length of gold wire. 3. Tuck one end of the wire between the gemstone and the cuff. Wrap the wire multiple times around the base of the gemstone.
4. Bring the wire up over the stone and down to one side and under the cuff, keeping the wire snug against the cuff. Continue wrapping the wire over the stone and under the cuff.
5. Tuck the end of the wire under the lip of
the gemstone but not on the inside of the cuff. Apply additional adhesive to keep the wire in place.
6. Using round nose pliers, gently twist the
wire along the top of the gemstone. The slight twisting tightens the wire on the gemstone.
6
Free Shipping . 10-25% Volume Discounts . Free Patterns
Shop now at www.primabead.com/gemstone
7
Materials:
# 34745033
Kumihimo Round Disc (1 pc)
$2.99
# 34745020
Metallic Blue Cord (1 pk)
# 34745035
$3.99
Kumihimo Beading Needle (1 pc)
$2.99
# 34745001
Metallic Blue Rondelles (1 pk)
# 34750022
$11.99
Silver Kumihimo Findings Pack (1 pk)
$3.99
# 34745036
Kumihimo Bobbins (1 pk)
# 22279001
$6.99
E6000® Glue (1 tube)
$3.40
Tools Needed:
Techniques to Know:
Round Nose Pliers #6858 Needle Nose Pliers #4454 Wire Cutters #4457
Kumihimo Round Braiding w/ Beads
Instructions: 1. Cut (4) 50” lengths of blue metallic cord. 2. Bring the cord ends together and fold in half. Bring the fold down through the center of the round disc.
3.
ut a scrap piece of cord (4+ inches) and C tie it onto the center fold from step 2.
4. Align the cords as explained in the
“Beaded Kumihimo” instruction booklet that came with the round disc.
5. Using the big eye beading needle,
thread (30) metallic beads onto each strand. This makes an 8” bracelet with cord ends. Use less or more beads on each of the eight cords to decrease or increase the overall length.
6. Wind each of the eight cords (with beads) onto a bobbin and close.
7. Follow the beaded instructions that
came with the disc. Braid the cord ½” before adding the beads. This section will be inserted into the clasp.
8. Braid a ¼” tail after all of the beads
have been braided in. Remove the cords from the bobbins and from the disc and tie them into a tight single knot. Remove the scrap cord from the other end.
9. Trim the excess cord. Next apply glue
to the ends of the cords and slide the cord ends on. Allow the glue to dry according to manufacturer instructions (2+ hours).
8
Free Shipping . 10-25% Volume Discounts . Free Patterns
Blue Iris
kumihimo bracelet
Shop now at www.primabead.com/blueiris
9
“DRESS LIKE IT.“ Life’s a party,
~Lilly Pulitzer
Francesca
bracelet
10
Free Shipping . 10-25% Volume Discounts . Free Patterns
Materials: # 34721066
4mm Bicone Mix (2 pks)
$4.00 # 34718096
Silver Large Double Link Chain (1 pk)
$4.00
Tools Needed: Round Nose Pliers #6858 Needle Nose Pliers #4454 Crimping Pliers #4501 Wire Cutters #4457
Techniques to Know: Crimp Tubes Opening Jump Rings Form a Wrapped Loop
# 34719059
Silver Findings Starter Pack (1 pk)
$4.00 # 3202002
Silver 7-Strand Beading Wire (1 pk)
$2.00
Instructions: 1. Cut (or separate using two pairs of pliers) the large double link chain into a 6 ½” section.
2. Attach (2) 6mm jump rings to each end of the chain.
3. Using 6mm jump rings, attach a lobster claw
clasp to one set of jump rings and attach an extender chain to the other set of jump rings.
4. Make a wrapped loop bicone drop and
attach the drop to the end of the extender chain.
5. Cut (2) 10” lengths of beading wire. 6. Using crimp tubes, attach each wire to a
6mm jump ring at one end of the double link chain.
7. Thread (44) bicones onto each wire. 8. Weave the bicone strands through the chain links.
9. Using crimp tubes, attach the beading wire
strands to the 6mm jump rings at the end of the chain. If it’s too difficult to weave the loose strands of beads, try crimping the wire, leaving a small loop for the jump ring to fit though. Then weave the strands through the double link chain.
Shop now at www.primabead.com/francesca
11
“CREATIVITY “ is an act of defiance.
~Twyla Tharp
12
Free Shipping . 10-25% Volume Discounts . Free Patterns
Caprise bracelet
Materials: # 34718010
Tools Needed: Needle Nose Pliers #4454 Wire Cutters #4457
Gold Small Curb Chain (2 pks)
$4.00
Techniques to Know:
# 34713033
Tying a Knot Opening Jump Rings
8mm Turquoise Round Beads (1 pk)
$4.00 # 3202302
.8mm Stretch Cord (1 pk)
$2.00
Instructions:
1. Using pliers, separate the chain into (28) 10-link lengths, each approximately 1 ½” long. 2. Cut (4) 14” lengths of stretch cord. Lay the (4) cords flat in a row, approximately ½” from each other.
3. Thread each cord through a single chain and thread a turquoise round onto cords 1 and 3. 4. Thread each cord through a single chain and thread a turquoise round onto cords 2 and 4. 5. Repeat steps 3-4 14 more times. Increase the overall length by repeating steps 3-4 again. 6. Tie each cord together into a double knot. Trim the excess cords. The tension of the stretch cord will move the chain so it surrounds the beads and forms a woven pattern.
Shop now at www.primabead.com/caprise
13
Triple Cabochon Bracelet Instructions: 1. Apply dabs of Quick Hold
7. Coil the wire up to the bezel of the center
2. Allow the glue to dry completely before
8. Repeat steps 5-7 to secure the second
glue to a set of round bezels and attach them to the back of an oval cabochon. Do not let the glue seep through the opening for the flat memory wire, otherwise, once the glue dries it won’t allow the wire to fit. Repeat this step for the remaining two cabochons. ®
continuing the bracelet.
cabochon. The sample has 1/2” of coil between each bezel. Bring the wire over the back side of the bezel and continue the coil. Repeat this step until the wire is coiled into (5) loops after the last cabochon. memory wire section.
3. Cut (2) single coils of bracelet memory wire. 9. Size the bracelet and trim 1/2” off the total size needed for each memory wire 4. Slide each cabochon onto the set of wires length. and position them at the center.
5. 6. Coil the wire onto the memory wire to the Cut a 48” length of gauge wire.
inner side of the end cabochon bezel. Coil the wire approximately (5) loops and press the coil snug. Bring the wire over the back side of the bezel and continue to coil it onto the memory wire.
Tools Needed: Round Nose Pliers #6858 Parrot Beak Pliers #4477 Wire Cutters #4457
10. Using E6000 , adhere the wire ends ®
to the memory wire and allow the adhesive to dry thoroughly.
Additional Patterns Available Online @ www.primabead.com/crackle
Techniques to Know: Wire Wrapping
Materials: # 74100073
# 9161
$3.99
$8.00
# 74100061
# 3201801
Gold Flat Bracelet Memory Wire (1 pk)
Gold Flat Memory Wire Ends (1 pk)
Gold 24 Gauge Wire (1 pk)
$2.99
$2.69
# 74100068
# 22279004
Gold Flat Memory Wire Round Bezels (1 pk)
$2.99 14
Gemocite Cabochon Mix (1 pk)
Quick Hold® & E6000® Mini Tubes (1pk)
$4.00
Free Shipping . 10-25% Volume Discounts . Free Patterns
Crackle Cabochon
jewelry
Shop now at www.primabead.com/crackle
15
Makes 2 bracelets
“CURIOSITY.“ The constant happiness is
~Alice Munro
16
Free Shipping . 10-25% Volume Discounts . Free Patterns
Materials: # 74100073
Gold Flat Memory Wire (1 pk)
$3.99 # 72099305
Gold Flower Cluster Pendant (1 pc)
$5.99
Tools Needed: Round Nose Pliers #6858 P arrot Beak Pliers #4477 *Used for Memory Wire
Techniques to Know: Form a Loop
Large Flower Bracelet Instructions: 1. Remove the chains, jump rings and
charms from the large flower. *These pieces will be used in the adjustable bracelet.
2. Cut a single coil of bracelet memory wire. 3. Form a loop to one side of the wire. Attach the smaller of the flower loops to the wire.
4. Form a partial loop at the other end of the wire, this should fit into the large loop of the flower. If the bracelet is too large, trim off a small section and form another loop.
Adjustable Flower Bracelet Instructions: 1. Cut a 1 1/2 coil of bracelet memory wire, approximately 12� in length.
2. Form a loop at each end of the wire. 3. Bend each loop inwards and overlap the
loops over the opposite ends of the wire, making the bracelets adjustable.
4. Using the jump rings from the accent,
attach the three charms to the bracelet.
Golden Flower Charm bracelets
Shop now at www.primabead.com/goldenflower
17
Materials: # 34722034
# 34708262
$4.00
$4.00
# 34741058
# 34719057
$4.00
$4.00
# 34719059
# 3202002
$4.00
$2.00
6mm Blue Pearl/Crystal Mix (1 pk)
6mm Dark Blue Mirror Beads (1 pk)
Silver Findings Starter Pack (1 pk)
Silver & Crystal Rondelle Spacer (3 pks)
Silver 8mm Jump Rings (1 pk)
Silver 7-Strand Beading Wire (1 pk)
Tools Needed: Needle Nose Pliers # 4454 Wire Cutters # 4457 Crimping Pliers # 4501
Techniques to Know: Opening Jump Rings Crimp Tubes
Instructions: 1. Cut (3) 10� lengths of beading wire. 2. Use a crimp tube to gather the (3)
wires together and attach them to an 8mm jump ring. Connect a toggle clasp end to the same jump ring.
3. Thread each beading wire strand through the holes of a 3-strand rondelle.
4. Thread (3) blue bicones onto one
of the end strands. Thread (2) blue bicones onto the middle strand. Thread (1) blue bicone onto the other end strand.
6. Thread (1) mirror bead onto the strand
containing (3) bicones. Thread (2) blue bicones onto the middle strand. Thread (3) mirror beads onto the strand containing (1) bicone.
7. Thread (1) 3-strand spacer onto the beading wire strands.
8. Thread (3) blue pearls onto the strand with
the single mirror bead and (3) crystals. Thread (2) blue pearls onto the strand with the (2) mirror beads and (2) crystals. Thread (1) blue pearl onto the strand with the (3) mirror beads and (1) crystal.
9. Thread (1) 3-strand spacer onto the beading wire strands.
10. Continue the pattern of beads until the bracelet is at the desired length.
11. Use a crimp tube to gather the (3) wires
together and attach them to an 8mm jump ring. Connect the other toggle clasp end to the same jump ring.
5. Thread (1) 3-strand spacer onto the beading wire strands.
18
Free Shipping . 10-25% Volume Discounts . Free Patterns
Molly
bracelet
Pattern Variations Available Online @ www.primabead.com/molly
Shop now at www.primabead.com/molly
19
Shared Hearts
bracelet & earrings
Tools Needed: Needle Nose Pliers #4454 Round Nose Pliers #6858 Crimping Pliers #4501
Techniques to Know: Forming a Loop Opening Jump Rings Cutting Chains
20
Free Shipping . 10-25% Volume Discounts . Free Patterns
Materials:
# 34718092
100 in/254cm Silver Small Curb Chain (1 pk)
# 34719059
$4.00
145pc Starter Pack Silver (1 pk)
$4.00
# 34722035
101 pc 6mm Pearl/Crystal Mix Red (1 pk)
# 34708289
$4.00
5pc Silver Deco Heart (1 pk)
$4.00
# 3202002
40’ .3mm 7-Strand Bead Wire- Silver (1 pk)
Instructions for Bracelet:
$2.00
1. Cut (10) 2 1/8” lengths of silver chain. Approx. 27 links each
2. Take (5) lengths of the chain and
connect each group of ends with a 2mm jump ring, then repeat with the other (5) lengths of chain.
3. Connect a 4mm jump ring to one
side of each grouping of chains (this will be where you connect the toggle clasps).
4. Using the 4mm jump rings you
just attached to the chain groups, connect the two ends of your toggle clasps.
5.
oving onto the center of the M bracelet. Begin by cutting a 4” strand of beading wire.
6. Crimp a small loop into one end of the wire, leaving about 1” on one side and 3 inches on the other.
7. Thread the beads in this order onto
the wire: bicone, heart, pearl, heart, bicone.
8.
lose the other end of the wire into C a loop using a crimp bead. (If you leave enough extra wire to feed back through the heart it will be easier to pull the wire and form a tighter loop).
9. Finally, connect either end of your
hearts to the 2mm jump rings on the ends of your pieces from steps 1-4.
Instructions for Earrings: 1. Cut (10) 1 ¼” lengths of chain. Approx. 19 links each
2. Thread (5) lengths of chain onto a 2mm jump ring
3. Now connect the 2mm jump ring to the loop on an eye pin.
4. Thread a pearl and then a bicone onto the eye pin and create a loop on the end.
5. To make sure that your earrings hang correctly, you’ll need to connect a 2mm jump ring on the end of your eye pin before you connect the earring wires.
6. Now repeat steps 1-5 to make the matching earring.
Shop now at www.primabead.com/sharedhearts
21
“Success
is liking yourself, liking what you do, and liking how you do it.
“
~Maya Angelou 22
Free Shipping . 10-25% Volume Discounts . Free Patterns
Turquoise Dream Materials:
bracelet
# 34719178
# 3202302
$3.00
$2.00
# 34741016
# 34712131
$4.00
$1.99
Cabochon Toggle (1 set)
Turquoise Bicone Mirror Beads (3 pks)
.8mm Stretch Cord (1 pk)
Silver Crimp Tubes (1 pk)
Tools Needed: Crimping Pliers #4501 Wire Cutters #4457
Techniques to Know: Crimp Tubes
Instructions: 1. Cut (5) 12� lengths of stretch cord. 2. Using crimp tubes, attach each length of stretch cord to one end of the toggle. Use separate crimp tubes for each length of cord.
3. Thread (35) beads onto each length of stretch cord. Use less or more depending on the overall length needed.
4. Use crimp tubes to attach each length of cord to the other end of the toggle. Use separate crimp tubes for each length of cord.
5. Trim the excess cords. Shop now at www.primabead.com/turquoise
23
$
25
CURRENTRESIDENT RESIDENT(OCCUPANT) (OCCUPANT)OR OR CURRENT
Casual
230+ pieces! Makes 2 Necklaces, 2 Bracelets & 2 sets of Earrings Bead Mat & 3-in-1 Tool Included
Makes 2 Necklaces, 2 Bracelets & 2 sets of Earrings
Bead Mat & 3-in-1 Tool Included
#34706-010
155+ pieces!
25
$
$
25
CLASS IN A BOX
#34706-009
Classic
*Coupon can only be redeemed once per customer.
Enter code above at checkout for a FREE GIFT with purchase!
12333ENTERPRISE ENTERPRISEBLVD. BLVD. 12333 LARGO,FL FL33773 33773 LARGO,
PRESORTED PRESORTED STANDARD STANDARD U.S.POSTAGE POSTAGE U.S. PAID PAID PRIMA BEAD PRIMA BEAD
Bead Mat & 3-in-1 Tool Included
Makes 2 Necklaces, 2 Bracelets & 2 sets of Earrings
255+ pieces!
#34706-011
Natural
Our friendly customer service team is here to assist you with placing your order. You can reach us at 800-366-2218 between 9:00am–4:30pm EST, Monday–Friday.
OVER THE PHONE
Our quick and easy checkout process makes ordering a breeze. Place an order at www.primabead.com 24 hours a day, 7 days a week.
ORDER ONLINE
JEWELRY
CREATE BEAUTIFUL
Let us help you