Napkin Decoupage

www.Projects4Crafters.com

Napkin Decoupage

Dish

STEP BY STEP 1. Basecoat the dish all over with white Decoupaint.

3. Use Matt Mod Podge to apply the designs to the dish and leave to dry for approx 30 mins.

4. Trim the excess napkin around the edge with scissors.

5. Apply 2-3 more coats of Mod Podge over the top leaving to dry between coats.

6. For a super smooth finish use wet sandpaper to lightly sand the surface and wipe clean with a soft cloth.

7. Repeat steps 2-6 for the back of the dish.

For photo step-by-steps check out the Papercrafts section on www.TheCraftLibrary.com

Materials

2. Remove the back 2 layers of a napkin and use a wet brush to separate the napkin motifs.

PappArt Dish (26 354 25) Mod Podge - Matt (26 113 01) Roses Napkin (16 616 10) White Decoupaint (93 166 01) Wet & Dry Sandpaper Soft Cloth Scissors Brushes and Water

Mod Podge - Hard Coat (62 112 45) Roses Napkin (16 612 60) Blackboard Foil (10 000 42) Ivory Decoupaint (93 166 06) Scissors or Knife, Ruler & Cutting Mat Brushes and Water Wet & Dry Sandpaper Soft Cloth Blue Card Letter Dies & Die Cutting Machine Narrow Double-sided Tape Wood Glue

Materials

mdf Memo Board (14 343 03)

STEP BY STEP 1. Basecoat the front and edges of the frame and the edges of the back panel with ivory Decoupaint.

2. Remove the back two layers of two napkins and use a wet brush to separate the napkin motifs.

3. Use Hard Coat Mod Podge to apply the designs to the front of the frame, wrapping them around the edges to the back, & leave to dry for approx 30 mins.

4. Apply 2-3 more generous coats of Mod Podge over the top leaving to dry between coats.

5. For a super smooth finish use wet sandpaper to lightly sand the surface and wipe clean with a soft cloth.

6. Stick the blackboard foil to the back panel before sticking the frame on top with wood glue.

7. Punch letters from the card and stick them in the aperture with double-sided tape.

Chalk Board

Mirror

STEP BY STEP 1. Basecoat the front & edges of the frame and the edges of the back panel with a mix of white and ivory Decoupaint.

3. Use Matt Mod Podge to apply the motifs to the front of the frame, wrapping them around the outside edges to the back & leave to dry for approx 30 mins.

4. Use a babywipe to apply a light patchy coat of yellow in between the motifs & leave to dry.

5. Apply 1-2 more coats of Mod Podge over the front & edges leaving to dry between coats.

6. Use wood glue to stick to frame to the backing & mirror adhesive to carefully stick the mirror in the aperture.

7. Use a small brush to stick the star & flower edges to the mirror with more Mod Podge.

Materials

2. Remove the back two layers of a napkin & use a wet brush to ‘cut’ out the flowers. Carefully cut the fairies out with scissors.

mdf Mirror (14 348 01) Mod Podge - Matt (26 113 01) Fairy Napkin (16 617 26) White Decoupaint (93 166 01) Ivory Decoupaint (93 166 06) Golden Yellow Decoupaint (93 164 08) Baby Wipe Scissors Brushes and Water Wood Glue Mirror Adhesive

Paper Mod Podge - Acid Free Gloss (62 112 38) Roses Napkin (16 612 60) Scissors Brush and Water

Materials

Candlelight Deco Bag (16 420 10)

STEP BY STEP 1. Remove the back 2 layers of a napkin.

2. Lay it over one side of the bag and gently apply the Mod Podge.

Use more pressing motions to push the Mod Podge through the napkin rather than brushing strokes.

3. Apply more Mod Podge through the napkin to approximately half way along each side.

4. Use a wet brush to remove the excess napkin at the sides and leave to dry.

5. Trim the excess top & bottom.

6. Repeat steps 1-5 for the other side.

Candle Bag

Note Box

STEP BY STEP 1. Basecoat the outside of the wooden slip box with white Decoupaint.

3. Use Matt Mod Podge to apply the napkin to the sides and back of the box. (You should be able to wrap one napkin around 3 sides.)

4. Leave to dry for approx 30 mins before trimming the excess top and bottom.

5. Use more pieces of napkin to cover the front of the box, trimming where necessary.

6. Apply 2 more coats of Mod Podge over the napkin, leaving to dry after each coat.

Materials

2. Remove the back two layers of a napkin.

Wooden Slip Box (14 326 91) Mod Podge - Matt (26 113 01) Bird Houses Napkin (16 613 06) White Decoupaint (93 166 01) Scissors Brushes and Water

Exterior Mod Podge (62 112 20) Roses Napkin (16 612 60) Pen Scissors Brush and Water

Materials

Metal Planter

STEP BY STEP 1. Lay a napkin over one side of the planter and carefully mark the sides and top of the planter with a pen.

2. Use scissors to trim the napkin and remove the back two layers.

3. Coat one side of the planter with a thin layer of Exterior Mod Podge.

4. Lay the trimmed napkin over the top, gently pressing down to adhere it.

5. Trim the bottom of the napkin to approximately 5 mm excess and wrap it over the edge of the base, using more Mod Podge to stick it in position.

6. Apply a generous coat over the top of the napkin & leave to dry.

7. Repeat Steps 1-6 for the other side.

8. When dry, apply 1-2 more coats and leave to dry for a week.

Planter

Family

STEP BY STEP 1. Basecoat the letters all over with two coats of white Decoupaint.

3. Use Matt Mod Podge to apply the designs to the letters and leave to dry for approx 30 mins.

4. Trim any excess napkin along the bottom edges with scissors.

5. Apply 2-3 more coats of Mod Podge over the top leaving to dry between coats.

Materials

2. Remove the back 2 layers of the napkins and use a wet brush to separate the napkin motifs.

PappArt Letter F (26 309 06) PappArt Letter A (26 309 01) PappArt Letter M (26 309 13) PappArt Letter I (26 309 09) PappArt Letter L (26 309 12) PappArt Letter Y (26 309 25) Mod Podge - Matt (62 113 01) Roses Napkin (16 616 10) White Decoupaint (93 166 01) Scissors Brushes and Water

Matt Mod Podge (62 112 38) Sparkle Mod Podge (62 112 38) Fairy Napkin (16 617 26) Ivory Decoupaint (93 166 06) Orange 4mm Acrylic Stones (14 960 16) Bright Pink 4mm Acrylic Stones (14 960 35) Light Blue 4mm Acrylic Stones (14 960 47) Dekofix Glue (91 211 05) Scissors Brush and Water Strong Tape

Materials

PappArt Suitcase (16 420 10)

STEP BY STEP 1. For extra strength stick a piece of strong tape down the spine of the case lid.

2. Basecoat the case with 2 coats of ivory Decoupaint.

3. Remove the back two layers from a napkin and carefully cut out the two fairies.

4. Use a wet brush to ‘cut’ out the flowers from a couple of napkins, leaving fluffy edges.

5. Use Matt Mod Podge to stick the flowers along the spine to hide the raised edge of the tape. Use more Mod Podge to stick the fairies above.

6. When dry, coat the whole case with Sparkle Mod Podge. Leave for 20 mins before coating with another layer of Matt Mod Podge.

7. When dry, stick acrylic stones on the fairy wands and on some of the flowers on the lid with Dekofix glue.

Small Case

Memo Board

STEP BY STEP 1. Lay the frame on the backing & mark the apertures with a pencil.

2. Basecoat the frame, backing apertures and all the edges with white Decoupaint.

4. Apply 3 coats of Mod Podge, leaving to dry between coats.

5. Use a babywipe to apply yellow and salmon Decoupaint to the frame. When dry, coat it with Mod Podge for protection.

6. Use wet sandpaper to lightly sand the backing smooth and dry with a soft cloth.

7. Trim the whiteboard foil to fit the bottom area of the backing and stick it in position.

8. Use wood glue to stick the frame to the backing.

mdf Memo Board (14 343 04)

Materials

3. Use Matt Mod Podge to apply the top layer of a napkin to the upper aperture area of the backing. When dry, trim the excess before repeating the process for the bottom area.

Mod Podge - Hard Coat (62 112 45) Roses Napkin (16 616 10) Whiteboard Foil (10 000 43) White Decoupaint (93 166 01) Golden Yellow Decoupaint (93 164 08) Salmon Decoupaint (93 164 18) Wet & Dry Sandpaper Soft Cloth Scissors and Pencil Brushes and Water Babywipes Wood Glue

Matt Mod Podge (62 112 38) Bird Houses Napkin (16 613 06) White Decoupaint (93 166 01) Computer & Printer for Titles Matt Varnish Spray (19 650 02) Brush and Water Optional:

Whiteboard Foil (10 000 43) Sticky Backed Ribbons

Materials for pages and binding: 4 Book Rings or Ribbons 17cm Paper/Card 2

Hole Punch Use a PappArt panel as a guide for punching holes in the pages. Use book rings or ribbons to bind the book.

Materials

Register PappArt Scrapbook (15 079 02)

STEP BY STEP 1. Basecoat all 4 book panels with white Decoupaint.

2. Remove the back 2 layers of a couple of napkins.

3. Use Matt Mod Podge to apply the napkins to the outside of the front and back panels.

4. When dry, trim the excess and use a wet brush to open up the binding holes.

5. Print the titles from a computer. Spray them with Matt Varnish and, when dry, cut them out. Use Mod Podge to stick them in position.

6. Apply a coat of Mod Podge over all the surfaces for protection.

7. Apply 2 more coats of Mod Podge over the outside covers, leaving to dry between coats.

Optional: Cut a square of whiteboard foil and stick it inside the cover. Use sticky backed ribbons to cover the edges.

Recipe Book

For more detailed instructions on how to decorate objects using napkin decoupage go to: www.TheCraftLibrary.com For step by step instructions with photos covering a variety of craft techniques and projects go to: www.Projects4Crafters.com To see the extensive range of products available from Efco Hobbygross gmbh go to: www.efco.sinotexuk.com

Š www.Projects4Crafters.com